Toshiba TV DVD Combo 26LV67 User Manual

Integrated High Definition  
LCD TV/DVD Combination  
HIGH-DEFINITION TELEVISION  
26LV67  
32LV67  
32LV67U  
Owner’s Record  
The model number and serial number are on the back of  
your TV. Record these numbers in the spaces below.  
Refer to these numbers whenever you communicate  
with your Toshiba dealer about this TV.  
For an overview of steps for setting up your new TV, see page 12.  
Note: To display a High Definition picture, the TV must be receiving a  
High Definition signal (such as an over-the-air High Definition TV  
broadcast, a High Definition digital cable program, or a High Definition  
digital satellite program). For details, please contact your TV antenna  
installer, cable provider, or satellite provider.  
Model number:  
Serial number:  
© 2007 TOSHIBA CORPORATION  
All Rights Reserved  
YC/M  
VX1A000360A0  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
15) CAUTION:  
• To reduce the risk of electric shock, do not use the  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
polarized plug with an extension cord, receptacle, or  
other outlet unless the blades can be inserted  
completely to prevent blade exposure.  
• To prevent electric shock, match wide blade of plug to  
wide slot; fully insert.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
16) WARNING:  
6) Clean only with dry cloth.  
To prevent the spread of fire, keep candles or other open  
flames away from this product at all times.  
7) Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8) Do not install near any heat sources such as radiators,  
heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
Installation, Care, and Service  
Installation  
Follow these recommendations and precautions and heed all  
warnings when installing your TV:  
9) Do not defeat the safety purpose of  
Wide blade  
the polarized or grounding type  
plug. A polarized plug has two blades  
with one wider than the other.  
A grounding type plug has two blades  
and a third grounding prong. The wide blade or the third  
prong are provided for your safety. If the provided plug  
does not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
17) Never modify this equipment. Changes or modifications  
may void: a) the warranty, and b) the user’s authority to  
operate this equipment under the rules of the Federal  
Communications Commission.  
18)  
DANGER: RISK OF  
SERIOUS PERSONAL  
INJURY, DEATH, OR  
10) Protect the power cord from being walked  
on or pinched, particularly at plugs,  
EQUIPMENT DAMAGE!  
Never place the TV on an unstable cart,  
stand, or table. The TV may fall, causing  
serious personal injury, death, or serious  
damage to the TV.  
convenience receptacles, and the point  
where they exit from the apparatus.  
11) Only use attachments/accessories specified by the  
manufacturer.  
19) To avoid damage to this product, never place or store the  
TV in direct sunlight; hot, humid areas; or areas subject to  
excessive dust or vibration.  
12) Use only with the cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the  
20) Always place the TV on the floor or a sturdy, level, stable  
surface that can support the weight of the unit. To secure  
the TV, use a sturdy tie from the hooks on the rear of the  
TV pedestal to a wall, pillar, or other immovable structure.  
Make sure the tie is tight, secure, and parallel to the floor.  
apparatus. When a cart is used, use  
caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or  
when unused for long periods of time.  
Sturdy tie (as short as possible)  
4"  
14) Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or plug  
is damaged, liquid has been spilled or objects have fallen  
into the apparatus, the apparatus has been exposed to  
rain or moisture, does not operate normally, or has been  
dropped.  
min.  
Hooks  
Clip  
Clip  
TV side  
TV top  
21) The apparatus shall not be exposed to dripping or  
splashing and that no objects filled with liquids, such as  
vases, shall be placed on the apparatus.  
Additional Safety Precautions  
14a) CAUTION: If the TV is dropped and the cabinet or  
enclosure surface has been damaged or the TV does not  
operate normally, take the following precautions:  
22) Never block or cover the slots or openings in the TV  
cabinet back, bottom, and sides. Never place the TV:  
• on a bed, sofa, rug, or similar  
surface;  
• too close to drapes, curtains, or  
walls; or  
• in a confined space such as a  
bookcase, built-in cabinet, or  
any other place with poor  
ventilation.  
The slots and openings are provided to protect the TV from  
overheating and to help maintain reliable operation of the  
TV. Leave a space of at least 4 (four) inches around the TV.  
• ALWAYS turn off the TV and unplug the power cord to  
avoid possible electric shock or fire.  
• NEVER allow your body to come in contact with any  
broken glass or liquid from the damaged television. The  
LCD panel inside the TV contains glass and a toxic  
liquid. If the liquid comes in contact with your mouth or  
eyes, or your skin is cut by broken glass, rinse the  
affected area thoroughly with water and consult your  
doctor.  
• ALWAYS contact a service technician to inspect the TV  
any time it has been damaged or dropped.  
(5 inches away from the TV slot side).  
(continued)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
23) Always place the back of the television at least four (4)  
inches away from any vertical surface (such as a wall) to  
allow proper ventilation.  
31)  
WARNING:  
RISK OF ELECTRIC SHOCK!  
Never spill liquids or push objects of any kind into the TV  
cabinet slots.  
24) Never allow anything to rest on or roll over the power cord,  
and never place the TV where the power cord is subject to  
wear or abuse.  
32) While it is thundering, do not touch the connecting cables  
or apparatus.  
25) Never overload wall outlets and extension cords.  
33) For added protection of your TV from lightning and power  
surges, always unplug the power cord and disconnect the  
antenna from the TV if you leave the TV unattended or  
unused for long periods of time.  
26) Always operate this equipment from a 120 VAC, 60 Hz  
power source only.  
27) Always make sure the antenna system is properly  
grounded to provide adequate protection against voltage  
surges and built-up static charges (see Section 810 of the  
National Electric Code).  
34) During normal use, the TV may make occasional snapping  
or popping sounds. This is normal, especially when the  
unit is being turned on or off. If these sounds become  
frequent or continuous, unplug the power cord and contact  
a Toshiba Authorized Service Center.  
Antenna lead-in wire  
Antenna discharge unit  
35)  
WARNING: RISK OF  
SERIOUS PERSONAL  
INJURY OR EQUIPMENT  
DAMAGE!  
(NEC Section 810-20)  
Ground clamp  
Grounding conductors  
(NEC Section 810-21)  
Never strike the screen with a sharp  
or heavy object.  
Electric service equipment  
36) • The LCD screen of this product can be damaged by  
ultraviolet radiation from the sun. When selecting a  
location for the television, avoid locations where the  
screen may be exposed to direct sunlight, such as in  
front of a window.  
Power service grounding  
electrode system (NEC Art 250 Part-H)  
Ground clamps  
28)  
DANGER: RISK OF SERIOUS  
PERSONAL INJURY OR DEATH!  
• Never touch, press, or place anything on the LCD  
screen. These actions will damage the LCD screen. If  
you need to clean the LCD screen, follow the  
instructions in item 30 on this page.  
• Use extreme care to make sure you are never in a  
position where your body (or any item you are in contact  
with, such as a ladder or screwdriver) can accidentally  
touch overhead power lines. Never locate the antenna  
near overhead power lines or other electrical circuits.  
• Never attempt to install any of the following during  
lightning activity: a) an antenna system; or b) cables,  
wires, or any home theater component connected to an  
antenna or phone system.  
Service  
37)  
WARNING:  
RISK OF ELECTRIC SHOCK!  
Never attempt to service the TV yourself. Opening and  
removing the covers may expose you to dangerous  
voltage or other hazards. Failure to follow this WARNING  
may result in death or serious injury. Refer all servicing not  
specified in this manual to a Toshiba Authorized Service  
Center.  
Care  
For better performance and safer operation of your TOSHIBA  
TV, follow these recommendations and precautions:  
29) If you use the TV in a room whose temperature is 32 ºF  
(0 ºC) or below, the picture brightness may vary until the  
LCD warms up. This is not a sign of malfunction.  
38) If you have the TV serviced:  
• Ask the service technician to use only replacement  
parts specified by the manufacturer.  
30) Always unplug the TV before  
cleaning. Gently wipe the  
display panel surface (the TV  
screen) using a dry, soft cloth  
only (cotton, flannel, etc.). A  
hard cloth may damage the  
surface of the panel. Avoid  
• Upon completion of service, ask the service technician  
to perform routine safety checks to determine that the  
TV is in safe operating condition.  
39) The cold cathode fluorescent lamp in the LCD panel  
contains a small amount of mercury.  
contact with alcohol, thinner, benzene, acidic or alkaline  
solvent cleaners, abrasive cleaners, or chemical cloths,  
which may damage the surface. Never spray volatile  
compounds such as insecticide on the cabinet. Such  
products may damage or discolor the cabinet.  
When the TV reaches the end of its useful life, dispose of  
the used TV by the approved method for your area, or ask  
a qualified service technician to properly dispose of the  
TV.  
Note: The lamp(s) inside this product contain  
mercury. Disposal may be regulated due to  
environmental considerations. For disposal or  
recycling information, contact your local authorities or the  
Electronics Industries Alliance (www.eiae.org).  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Choosing a location for your LCD TV  
Safety and Care Information for  
TV/DVD Combination Models  
To Display your LCD TV on the included Pedestal  
Stand:  
DISC SLOT  
Observe the following safety precautions:  
• Keep your fingers well clear of the disc slot when the disc is  
loading or unloading. Neglecting to do so may cause personal  
injury.  
1) Read and Follow the pedestal assembly instructions included  
with the pedestal.  
CAUTION: Before beginning pedestal assembly, carefully lay  
the front of the LCD Panel face down on a flat, cushioned  
surface such as a quilt or blanket. Leave the bottom of the unit  
protruding over the edge of the surface and assemble the  
pedestal as indicated below.  
LASER BEAM  
• Never look into the opening of the disc slot or ventilation  
opening of the product to see the source of the laser beam.  
Staring directly at the beam may cause permanent damage to  
your eyesight.  
Note: Extreme care should always be used when attaching  
the pedestal stand to avoid damage to the LCD panel.  
2) Place the TV on a sturdy, level surface that can support the  
weight of the TV.  
3) Be sure to secure the TV to a wall, pillar, surface, or other  
immovable structure. To secure the TV in this manner, use the  
included strap located at the rear of pedestal stand. (-item 20,  
page 3).  
DISC  
• Do not use a cracked, deformed, or repaired disc. These discs  
are easily broken and may cause serious personal injury and  
product malfunction.  
Precautions  
To Display your LCD TV using a Wall Bracket:  
If you decide to wall mount your LCD TV, always use a UL-  
listed wall bracket appropriate for the size and weight of the  
LCD TV (- page 2) :  
VIBRATION  
• Vibration or shock may disrupt DVD playback or cause  
scratches on the disc. Do not move or tilt or otherwise jolt the  
TV when a disc is loaded. The playback sound may skip if the  
TV is dropped from a height of 1.58 inch (4 cm) or more or if  
the TV is installed at a greater angle than recommended.  
1) CAUTION: Two people are required for installation.  
2) Unplug and remove any cables and/or other component  
connectors from the rear of the TV.  
3) Follow the instructions provided with your wall bracket.  
Before proceeding, make sure the appropriate bracket(s) are  
attached to the wall and the back of the TV as described in the  
instructions provided with the wall bracket.  
4) After attaching the appropriate bracket(s) to the wall and the  
back of the TV, remove the pedestal stand from the TV as  
described below.  
Notes on moisture condensation  
Moisture condensation occurs, for example, when you pour a  
cold drink into a glass on a warm day. Drops of water form on  
the outside of the glass. In the same way, moisture may  
condense on the optical pick-up lens inside the DVD player,  
one of the most crucial internal parts of the DVD player.  
Removing the Pedestal Stand  
1) Carefully lay the front of the unit face down on a flat,  
cushioned surface such as a quilt or blanket. Leave the stand  
protruding over the edge of the surface.  
o
f
n
s
Optical pick-up  
lens  
Note: Extreme care should always be used when removing  
the pedestal stand to avoid damage to the LCD panel.  
2) Remove the jack pack cover on the back of the TV to expose  
the pedestal stand screws. The jack pack cover can be removed  
without tools.  
3) Remove the five screws shown in the diagram below. This will  
allow removal of the pedestal stand.  
4) Once you have removed all five screws holding the pedestal  
stand in place, remove the pedestal stand from the TV by  
sliding the pedestal stand away from the TV.  
Moisture condensation can occur in the following  
conditions:  
• When the TV is moved directly from a cold or air conditioned  
area to a warm or humid area.  
• When the TV is placed in an area in which the heat has just  
been turned on, or where cold air from an air conditioner falls  
directly on the TV.  
Five screws  
(continued)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not use the DVD player when moisture condensation  
may be present.  
On storing discs  
• Never store discs near heat sources or in an area subject to  
direct sunlight.  
• Never store discs in places subject to moisture and dust (such  
as near a humidifier or in a bathroom).  
• Store discs vertically in a case. Stacking or placing objects on  
discs outside of their case may cause warping.  
If you use the DVD player in such a situation, the DVD player  
and/or discs may become damaged. Connect the power cord of  
the TV to the wall outlet, turn on the TV, remove the disc, and  
leave the TV on for two or three hours. After two or three hours,  
the TV will have warmed up and evaporated any moisture.  
Leaving the TV connected to the wall outlet will help prevent  
moisture condensation in the TV or DVD player.  
Structure of disc contents  
Normally, DVD video discs are divided into titles, and the titles  
are sub-divided into chapters. Video CDs and Audio CDs are  
divided into tracks.  
Wall outlet  
DVD video disc  
DVD video disc  
Title 1  
Title 2  
Chapter 1 Chapter 2  
Chapter 1 Chapter 2 Chapter 3  
Notes on discs  
On handling discs  
• Do not touch the playback side of the disc.  
For example, handle the disc as shown below.  
Video CD/Audio CD  
Video CD/Audio CD  
Track 2 Track 3 Track 4  
Track 1  
Track 5  
DO  
Each title, chapter or track is assigned a number (the “title  
number,” “chapter number,” and “track number,” respectively).  
Playback side  
Some discs do not have these numbers.  
• Do not attach paper or tape to discs.  
Notes on copyright  
DO NOT  
The unauthorized recording, use, distribution, or  
revision of television programs, videotapes, DVDs, and  
other materials is prohibited under the Copyright Laws  
of the United States and other countries, and may  
subject you to civil and criminal liability.  
On cleaning discs  
• Fingerprints and dust on discs cause picture and sound  
deterioration. Wipe discs from the center outward with a soft  
cloth. Always keep discs clean.  
This product incorporates copyright protection technology that  
is protected by U.S. patents and other intellectual property  
rights. Use of this copyright protection technology must be  
authorized by Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise authorized by  
Macrovision. Reverse engineering or disassembly is prohibited.  
DO  
DO NOT  
• Never use any type of solvent (such as thinner, benzine,  
commercially available cleaners or antistatic spray for vinyl  
LPs). Using such solvents may damage the discs.  
Notes on region numbers  
The region number of this DVD player of the TV is 1. If region  
numbers, which stand for their playable area, are printed on  
1
ALL  
your DVD video disc and you do not find  
or  
, disc  
playback will not be allowed by the DVD player. (In this case,  
the TV will display a message on-screen.)  
Some DVDs that have no region code label may still be subject  
to area restrictions and are therefore not playable.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Playable discs  
This DVD player can play the following discs with the  
corresponding logo.  
CAUTION:  
THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER  
SYSTEM.  
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE  
READ THIS OWNER’S MANUAL CAREFULLY AND  
RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT  
REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED  
SERVICE LOCATION.  
USE OF CONTROLS OR ADJUSTMENTS, OR THE  
PERFORMANCE OF PROCEDURES OTHER THAN  
THOSE SPECIFIED HEREIN, MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
TO PREVENT DIRECT EXPOSURE TO THE LASER  
BEAM, NEVER TRY TO OPEN THE ENCLOSURE.  
VISIBLE LASER RADIATION MAY BE PRESENT WHEN  
THE ENCLOSURE IS OPENED. NEVER STARE INTO THE  
BEAM.  
Maximum  
Disc  
Size  
Disc Mark Contents  
playback time  
Approx. 4 hours  
(single-sided disc)  
12 cm  
8 cm  
Audio  
+
Video  
(moving  
pictures)  
Approx. 8 hours  
(double-sided disc)  
DVD  
video  
discs  
Approx. 30 minutes  
(single-sided disc)  
Approx. 60 minutes  
(double-sided disc)  
Audio  
+
Video  
Video  
CDs  
12 cm  
Approx. 74 minutes  
(moving  
pictures)  
DIGITAL VIDEO  
Location of required label  
12 cm  
8 cm  
Approx. 74 minutes  
Approx. 22 minutes  
HONG KONG TOHEI E.M.C. CO.,LTD.  
Audio  
CDs  
Unit No.D,9th Floor, Spectrum Tower,  
53 Hung To Road,Kwun Tong,Kowloon,  
Hong Kong  
CLASS 1 LASER PRODUCT  
Audio  
CAUTION:VISIBLE AND INVISIBLE  
LASER RADIATION WHEN OPEN  
AVOID EXPOSURE TO BEAM  
COMPLIES WITH 21 CFR  
1040.10 AND 1040.11  
EXCEPT FOR DEVIATIONS  
PURSUANT TO LASER  
NOTICE NO.50, DATED  
(JULY 26, 2001 ).  
The following discs may also be compatible:  
DVD-R/RW discs in DVD video format.  
CD-R/CD-RW discs in CD-DA, Video CD, MP3,  
or JPEG format.  
Kodak Picture CD and FUJICOLOR CD format.  
• You cannot play discs other than those listed above. You  
cannot play discs in formats such as DVD-RAM, DVD-ROM,  
Photo CD, Super Audio CD (SACD™), etc., or non  
standardized discs even if they may be labeled as above. The  
damage depending on the use of those discs is NOT covered  
under your Toshiba warranty.  
Slot - in DVD / CD player  
module DVC - 303S - TO  
No.XXXXX  
• Some CD-R/RWs cannot be played back depending on the  
recording conditions.  
• This TV uses the NTSC color system, and cannot play DVD  
video discs recorded in any other color system (for example,  
PAL or SECAM).  
• Do not use the CD single adapter since it may not play  
properly.  
Because of problems and errors that can occur during the  
creation of DVD and CD software and/or the manufacture of  
DVD and CD discs, Toshiba cannot assure that the DVD  
player contained in your TV/DVD Combination will  
successfully play every disc bearing the DVD and CD logos.  
If you happen to experience any difficulty playing a DVD  
and/or CD disc on the DVD player contained in your TV/DVD  
Combination, please contact Toshiba Customer Service.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Declaration of Conformity Important notes about your LCD  
Compliance Statement  
(Part 15):  
TV/DVD combination  
The following symptoms are technical limitations of LCD  
Display technology and are not an indication of malfunction;  
therefore, Toshiba is not responsible for perceived issues  
resulting from these symptoms.  
The Toshiba 26LV67, 32LV67 and 32LV67U Televisions  
comply with Part 15 of the FCC rules.  
1) An afterimage (ghost) may appear on the screen if a fixed, non-  
moving image is displayed for a long period of time. The  
afterimage is not permanent and will disappear in a short period  
of time.  
2) The LCD panel contained in this TV is manufactured using an  
extremely high level of precision technology; however, there  
may be an occasional pixel (dot of light) that does not operate  
properly (does not light, remains constantly lit, etc.). This is a  
structural property of LCD technology, is not a sign of  
malfunction, and is not covered under your warranty. Such  
pixels are not visible when the picture is viewed from a normal  
viewing distance.  
Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that  
may cause undesired operation.  
The party responsible for compliance to these rules is:  
Toshiba America Consumer Products, L.L.C.  
82 Totowa Rd. Wayne, NJ 07470.  
Ph: 1-800-631-3811  
Note: This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to Part 15  
of the FCC rules. These limits are designed to provide  
reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses, and  
can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is  
no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by  
removing and applying power to the equipment, the user is  
encouraged to try to correct the interference by one or more of  
the following measures:  
Note: Interactive video games that involve shooting a “gun”  
type of joystick at an on-screen target may not work with this  
TV.  
About this owner’s manual (DVD  
player section)  
This owner’s manual explains the basic instructions for using the  
internal DVD player. Some DVDs are produced in a manner that  
allows specific or limited operation during playback. As such, the  
DVD player may not respond to all operating commands. This is  
not a defect in the DVD player.  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and the  
receiver.  
• Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Refer to the instructions provided with your DVDs.  
• Consult the dealer or an experienced radio/TV technician for  
help.  
If the symbol “ ” appears on-screen during DVD operation, it  
means that the operation or feature is not permitted or available for  
the DVD player or disc.  
Caution: Changes or modifications to this equipment not  
expressly approved by Toshiba could void the user’s authority  
to operate this equipment.  
For example, sometimes the DVD player is unable to stop  
playback of the DVD’s copyright message when the D button is  
pressed.  
Trademark Information  
• WOW, SRS and l symbol are trademarks of SRS Labs, Inc.  
WOW technology is incorporated under license from SRS Labs, Inc.  
• Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are registered trademarks of Dolby  
Laboratories.  
• HDMI, the HDMI logo and High-Definition Multimedia Interface are  
trademarks or registered trademarks of HDMI Licensing LLC.  
is a trademark of DVD Format/Logo Licensing Corporation.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Switching between two channels using SurfLock. . . . 41  
Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
Scrolling the TheaterWide® picture  
Important Safety Instructions .......................................... 3  
Installation, Care, and Service ........................................ 3  
(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 43  
Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 44  
Selecting the cinema mode (480i and 1080i signals) . . . . . . 44  
Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Selecting the picture mode. . . . . . . . . . . . . . . . . . . . . . . 45  
Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 45  
Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 46  
Base closed captions . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
Digital CC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
CC Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Adjusting the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
Using the digital audio selector . . . . . . . . . . . . . . . . . . . 47  
Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 48  
Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 48  
Using the StableSound® feature. . . . . . . . . . . . . . . . . . . 49  
Selecting the optical audio output format . . . . . . . . . . . 49  
Using the Dolby® Digital Dynamic Range  
Safety and Care Information for  
TV/DVD Combination Models .......................................... 5  
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Overview of steps for installing, setting up, and using  
your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
TV front and side panel controls and connections . . . . . . . . 13  
TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Chapter 2: Connecting your TV . . . . . . . . . . . . . . . . . . . . . . .15  
Overview of cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
About the connection illustrations . . . . . . . . . . . . . . . . . . . . 15  
Connecting a VCR and antenna or Cable TV  
(no Cable box) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Connecting a VCR with S-video and a cable box . . . . . . . . 17  
Connecting a DVD player with ColorStream®  
(component video), a VCR, and a satellite receiver. . . . 18  
Connecting a camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Connecting an HDMIor DVI device to the HDMI  
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Connecting a digital audio system . . . . . . . . . . . . . . . . . . . . 21  
Connecting an audio system . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Connecting a personal computer (PC) . . . . . . . . . . . . . . . . . 22  
Control feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49  
Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 50  
If you cannot remember your PIN code. . . . . . . . . . . . . 50  
Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 50  
Blocking TV programs and movies by rating  
(V-Chip) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51  
Downloading an additional rating system for blocking  
TV programs and movies . . . . . . . . . . . . . . . . . . . . 51  
Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52  
Unlocking programs temporarily . . . . . . . . . . . . . . . . . . 53  
Using the input lock feature . . . . . . . . . . . . . . . . . . . . . . 53  
Using the control panel lock feature . . . . . . . . . . . . . . . 54  
Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . . . 54  
Setting the PC Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Displaying TV status information. . . . . . . . . . . . . . . . . . . . . 56  
Understanding the auto power off feature . . . . . . . . . . . . . . 56  
Understanding the last mode memory feature . . . . . . . . . . . 56  
Chapter 3: Using the remote control . . . . . . . . . . . . . . . . . . .23  
Preparing the remote control for use. . . . . . . . . . . . . . . . . . . 23  
Installing the remote control batteries . . . . . . . . . . . . . . . . . 23  
Remote control effective range. . . . . . . . . . . . . . . . . . . . . . . 23  
Learning about the remote control . . . . . . . . . . . . . . . . . . . . 24  
Using the remote control to control your other devices . . . . 25  
Remote Control functional key chart . . . . . . . . . . . . . . . . . . 26  
Programming the remote control to control your other  
devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Remote control codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Chapter 4: Menu layout and navigation . . . . . . . . . . . . . . . . .30  
Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 31  
Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 31  
Chapter 7: Using the TV’s advanced features . . . . . . . . . . . . .57  
Using the advanced picture settings features . . . . . . . . . . . . 57  
Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 57  
Using the static gamma feature . . . . . . . . . . . . . . . . . . . 57  
Selecting the color temperature . . . . . . . . . . . . . . . . . . . 58  
Using CableClear® digital noise reduction . . . . . . . . . . 58  
Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 59  
Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 59  
Using the advanced audio settings features . . . . . . . . . . . . . 60  
Using the SRS WOWsurround sound feature . . . . . . 60  
Chapter 5: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .32  
Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 32  
Configuring the antenna input source for the ANT  
terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Programming channels into the TV’s channel memory . . . . 33  
Programming channels automatically . . . . . . . . . . . . . . 33  
Manually adding and deleting channels in the channel  
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Labeling channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
Setting the HDMIaudio mode. . . . . . . . . . . . . . . . . . . . . . 35  
Viewing the digital signal meter. . . . . . . . . . . . . . . . . . . . . . 36  
Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Chapter 8: DVD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . .61  
Playing a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
Basic playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
Using the DVD aspect ratio feature . . . . . . . . . . . . . . . . . . . 63  
Playing in fast reverse or fast forward . . . . . . . . . . . . . . . . . 63  
To pause playback (still playback) . . . . . . . . . . . . . . . . . . . 63  
Playing frame by frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Playing in slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Locating a chapter or track . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Changing angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Title selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64  
Changing soundtrack language . . . . . . . . . . . . . . . . . . . . . . 65  
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65  
Disc status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66  
(continued)  
Chapter 6: Using the TV’s features . . . . . . . . . . . . . . . . . . . .38  
Selecting the video input source to view . . . . . . . . . . . . . . . 38  
Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 38  
Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Tuning channels using the Channel Browser. . . . . . . 39  
Tuning to the next programmed channel . . . . . . . . . . . . 41  
Tuning to a specific channel (programmed or  
unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Switching between two channels using Channel  
Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
MP3/JPEG CD operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 66  
MP3/JPEG CD information . . . . . . . . . . . . . . . . . . . . . 66  
MP3 CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67  
JPEG CD playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68  
Chapter 9: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .69  
General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69  
DVD Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70  
LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71  
Chapter 10: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72  
Limited United States Warranty  
for LCD TV/DVD Combinations 26” and Larger . . . . . 73  
Limited Canadian Warranty  
for Toshiba Brand Flat Panel Televisions . . . . . . . . . . . 74  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Introduction  
Welcome to Toshiba  
Features of your new TV  
Thank you for purchasing this Toshiba LCD TV/DVD  
combination, one of the most innovative LCD TVs on the  
market. This digital television is capable of receiving analog  
basic, digital basic and digital premium cable television  
programming by direct connection to a cable system providing  
such programming. A security card provided by your cable  
operator is required to view encrypted digital programming.  
Certain advanced and interactive digital cable services such as  
video-on-demand, a cable operator's enhanced program guide  
and data-enhanced television services may require the use of a  
set-top box. For more information call your local cable  
operator.  
The following are just a few of the many exciting features of  
your new Toshiba widescreen, integrated HD, LCD TV:  
Integrated digital tuning (8VSB ATSC and QAM)  
eliminates the need for a separate digital converter set-top  
box (in most cases).  
Three HDMIdigital, high-definition multimedia  
interfaces 1080p input support (- page 20).  
Two sets of ColorStream® HD high-resolution component  
video inputs (- page 18).  
SRS WOWaudio technologies (- page 60).  
Digital Audio Out optical audio connection with Dolby®  
Digital optical output format (- page 49).  
CableClear® digital picture noise reduction  
(- page 58).  
PC IN (Analog RGB) computer terminal (- page 22).  
DVD video (and Video CD, Audio CD) player  
(- page 61).  
Channel Labeling allows you to put the Call Letters (e.g.  
ABC, HBO, etc.) on the screen along with the station  
numbers, so you always know what you’re watching  
(- page 34).  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Introduction  
10 See “Menu layout and navigation” for a quick overview of  
Overview of steps for installing,  
setting up, and using your new TV  
navigating the TV’s menu system (- page 30).  
11 Program channels into the TV’s channel memory  
(- page 33).  
12 For details on using the TV’s features, see Chapters 6  
Follow these steps to set up your TV and begin using its many  
exciting features.  
and 7.  
13 For details on using the DVD’s features, see Chapter 8.  
14 For help, refer to the Troubleshooting Guide, Chapter 9.  
1
2
Carefully read the important safety, installation, care, and  
service information. Keep this manual for future  
reference.  
15 For technical specifications and warranty information, see  
Chapter 10.  
Observe the following when choosing a location for the  
TV:  
Read “Important notes about your LCD TV/DVD  
16 Enjoy your new TV/DVD!  
combination” (- page 8).  
Place the TV on the floor or a sturdy, level, stable  
surface that can support the weight of the unit. Secure  
the TV to a wall, pillar, or other immovable structure  
(- page 3).  
Place the TV in a location where light does not reflect  
on the screen.  
Place the TV far enough from walls and other objects to  
allow proper ventilation. Inadequate ventilation may  
cause overheating, which will damage the TV. THIS  
TYPE OF DAMAGE IS NOT COVERED UNDER  
THE TOSHIBA WARRANTY.  
3
4
Do not plug in any power cords until AFTER you have  
connected all cables and devices to your TV.  
BEFORE connecting cables or devices to the TV, learn  
the functions of the TV’s connections and controls  
(- pages 13–14).  
5
Connect your other electronic device(s) to the TV  
(- pages 15–22).  
6
7
Install the batteries in the remote control (- page 23).  
See “Learning about the remote control” (- page 24) for  
an overview of the buttons on the remote control.  
8
9
Program the remote control to operate your other  
device(s) (- pages 25–29).  
AFTER connecting all cables and devices, plug in the  
power cords for your TV and other devices. The yellow  
LED will blink until the TV goes into standby mode.  
When the TV is in standby mode, press POWER on the  
TV control panel or remote control to turn on the TV.  
If the TV stops responding to the controls on the remote  
control or TV control panel and you cannot turn the TV  
off or on, press and hold the POWER button for 5  
seconds to reset the TV.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Introduction  
TV front and side panel controls and connections  
Left side panel  
Right side panel  
TV front  
4
11  
12  
8
9
5
13  
14  
15  
6
7
10  
TV top  
Control panel  
3
DISC  
POWER  
1
2
1
Green and Yellow LEDs  
Green = Power indicator  
Yellow = Disc indicator  
8
CHANNEL Bb — When no menu is on-screen, these  
buttons change the channel (programmed channels only;  
- page 33).  
9
VOLUME C c — These buttons adjust the volume level.  
See “LED indications” on page 71 for additional  
information.  
10 INPUT — Repeatedly press to change the source you are  
viewing (ANT, Built-In DVD, VIDEO 1, VIDEO 2,  
ColorStream HD1, ColorStream HD2, HDMI 1,  
HDMI 2, HDMI 3, PC).  
2
3
4
Remote sensor — Point the remote control toward this  
remote sensor (- “Remote control effective range” on  
page 23).  
11 PLAY — Press to play a DVD video disc, or other  
VIDEO-2 IN — The side panel A/V connections are  
referred to as “VIDEO 2” and include standard A/V  
connections.  
playable disc.  
12 STOP — Press to stop a DVD video disc, or other  
playable disc.  
POWER — Press to turn the TV on and off.  
If the TV stops responding to the controls on the remote  
control or TV control panel and you cannot turn off the  
TV, press and hold the POWER button on the TV control  
panel for 5 or more seconds to reset the TV.  
13 SKIP — Press to skip DVD chapter, or CD track.  
14 OPEN/CLOSE — Press to eject a disc.  
15 DVD disc slot — Insert a playable disc to play.  
5
6
ARROWS BbC c — When a menu is on-screen, these  
buttons function as up/down/left/right menu navigation  
buttons.  
MENU (ENTER) — Press to access the menu system  
(- pages 30–31). When a menu is on-screen, the MENU  
button on the TV’s control panel functions as the ENTER  
button.  
7
EXIT — Press to instantly close an on-screen menu.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1: Introduction  
TV back panel connections  
For an explanation of cable types and connections, see pages 15–22.  
1
2
TV back  
Power cord  
Cable Clamper  
3
4
8
9
5
6 7  
1
2
ColorStream® HD-1 and ColorStream® HD-2 —  
Two sets of ColorStream® high-definition component  
video inputs (with standard stereo audio inputs) for  
connecting devices with component video output, such as  
a Toshiba DVD player with ColorStream®.  
7
8
9
Digital Audio OUT — Optical audio output in Dolby  
Digital or PCM (pulse-code modulation) format for  
connecting an external Dolby Digital decoder, amplifier,  
A/V receiver, or home theater system with optical audio  
input.  
HDMIIN — High-Definition Multimedia Interface  
input receives digital audio and uncompressed digital  
video from an HDMI device or uncompressed digital  
video from a DVI device. Also see item 4. HDMI  
connection is necessary to receive 1080p signals.  
Note: Component video cables carry only video  
information; separate audio cables are required for a  
complete connection.  
VIDEO-1 IN — Standard (composite) video and standard  
audio inputs plus optional S-video inputs for connecting  
devices with composite video or S-video output.  
Service port — For service use only. Used for updating  
the television’s firmware.  
Note: Standard (composite) video and S-video cables  
carry only video information; separate audio cables are  
required for a complete connection.  
HDMI, the HDMI logo and High-Definition Multimedia Interface are  
trademarks or registered trademarks of HDMI Licensing LLC.  
Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are registered trademarks of Dolby  
Laboratories.  
3
4
Fixed Audio OUT — Analog audio outputs for  
connecting an audio amplifier.  
PC/HDMI-1 (AUDIO) IN — PC audio input terminals  
are shared with HDMI-1 analog audio input terminals, and  
their use can be configured in the Audio Setup menu  
(- page 55).  
5
6
PC IN — For use when connecting a personal computer.  
ANT — Antenna input that supports analog (NTSC) and  
digital (ATSC) off-air antenna signals and analog and  
digital Cable TV (QAM) signals.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
HDMIcable cable (with HDMI Logo “  
”)  
Overview of cable types  
Cables can be purchased from most stores that sell audio/video  
devices. Before purchasing any cables, be sure of connector  
types required by your devices and the length of each cable.  
HDMI (High-Definition Multimedia Interface) cable is for use  
with devices with an HDMI output. An HDMI cable delivers  
digital audio and video in its native format. This cable carries  
both video and audio information; therefore, separate audio  
cables are not required for a complete HDMI device  
connection (- page 20 and page 22).  
Coaxial (F-type) cable  
Note: HDMI cable provides better picture performance than a  
standard (composite) video or S-video cable.  
Coaxial (F-type) cable is used for connecting your antenna,  
cable TV service, and/or cable converter box to the ANT input  
on your TV.  
Optical audio cable  
Standard A/V cables (red/white/yellow)  
Optical audio cable is for connecting receivers with Dolby  
Digital or PCM (pulse-code modulation) optical audio input to  
the TV’s DIGITAL AUDIO OUT terminal (- page 21).  
Standard A/V cables (composite video) usually come in sets of  
three, and are for use with video devices with analog audio and  
composite video output. These cables (and the related inputs  
on your TV) are typically color-coded according to use: yellow  
for video, red for stereo right audio, and white for stereo left  
(or mono) audio.  
Analog RGB (15-pin) computer cable  
Analog RGB (15-pin) computer cable is for connecting a PC to  
the TV’s PC IN terminal (- page 22).  
S-video cable  
S-video cable is for use with video devices with S-video  
output. Separate audio cables are required for a complete  
connection.  
About the connection illustrations  
You can connect different types and brands of devices to your  
TV in several different configurations. The connection  
illustrations in this manual are representative of typical device  
connections only. The input/output terminals on your devices  
may differ from those illustrated herein. For details on  
connecting and using your specific devices, refer to each  
device’s owner’s manual.  
Note: An S-video cable provides better picture performance  
than a composite video cable. If you connect an S-video cable,  
be sure to disconnect the standard (composite) video cable or  
the picture performance will be unacceptable.  
Component video cables (red/green/blue)  
Component video cables come in sets of three and are for use  
with video devices with component video output.  
(ColorStream® is Toshiba’s brand of component video.) These  
cables are typically color-coded red, green, and blue. Separate  
audio cables are required for a complete connection.  
Note: Component video cables provide better picture  
performance than a standard (composite) video or S-video  
cable.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
Connecting a VCR and antenna or Cable TV (no Cable box)  
TV upper back panel  
From Cable TV or antenna  
Stereo VCR  
VIDEO  
AUDIO  
L
R
IN  
IN from ANT  
OUT to TV  
CH 3  
CH 4  
OUT  
R
L
TV lower back panel  
You will need:  
To view the antenna or Cable signal:  
Select the ANT video input source on the TV.*  
coaxial cables  
standard A/V cables  
To view the VCR:  
Turn ON the VCR. Select the VIDEO 1 video input source on  
the TV.*  
– For better picture performance, if your VCR has S-video,  
use an S-video cable (plus the audio cables) instead of  
the standard video cable. Do not connect both types of  
video cable to VIDEO 1 at the same time or the picture  
performance will be unacceptable.  
– If you have a mono VCR, connect L/MONO on the TV to  
your VCR’s audio out terminal using the white audio cable  
only.  
* To select the video input source, press INPUT on the remote control  
(- page 24). To program the TV remote control to operate other  
devices, see Chapter 3.  
The unauthorized recording, use, distribution, or revision of  
television programs, videotapes, DVDs, and other materials is  
prohibited under the Copyright Laws of the United States and  
other countries, and may subject you to civil and criminal  
liability.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
Connecting a VCR with S-video and a cable box  
An S-video connection will provide better picture performance than a standard (composite) video cable.  
From Cable TV  
TV upper back panel  
Cable box  
IN  
CH 3  
CH 4  
OUT  
stereo VCR  
VIDEO  
AUDIO  
L
R
IN  
IN from ANT  
OUT to TV  
CH 3  
CH 4  
OUT  
R
L
TV lower back panel  
You will need:  
To view basic and premium Cable channels:  
Turn OFF the VCR. Select the ANT video input source on the  
TV.* Tune the TV to channel 3 or 4 (whichever channel the  
Cable box output is set to). Use the Cable box controls to  
change channels.  
coaxial cables  
S-video cable  
– Do not connect both types of video cable to VIDEO 1 at  
the same time or the picture performance will be  
unacceptable.  
To view the VCR:  
Turn ON the VCR. Select the VIDEO 1 video input source on  
the TV.*  
standard audio cables  
– If you have a mono VCR, connect L/MONO on the TV to  
your VCR’s audio out terminal using the white audio cable  
only.  
* To select the video input source, press INPUT on the remote control  
(- page 24). To program the TV remote control to operate other  
devices, see Chapter 3.  
Note: When you use a Cable box, you may not be able to use  
the remote control to program or access certain features on the  
TV.  
The unauthorized recording, use, distribution, or revision of  
television programs, videotapes, DVDs, and other materials is  
prohibited under the Copyright Laws of the United States and  
other countries, and may subject you to civil and criminal  
liability.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
Connecting a DVD player with ColorStream® (component video), a VCR,  
and a satellite receiver  
Your TV has two sets of ColorStream® (component video) inputs.  
TV upper back panel  
From antenna  
Stereo VCR  
AUDIO  
OUT  
L
VIDEO  
AUDIO  
Y
PB  
PR  
L
R
IN  
IN from ANT  
OUT to TV  
R
COMPONENT VIDEO  
VIDEO  
OUT  
CH 3  
CH 4  
S-VIDEO  
OUT  
OUT  
DVD player with component video  
R
L
From satellite dish  
AUDIO  
OUT  
L
Y
PB  
PR  
R
VIDEO  
OUT  
COMPONENT VIDEO  
Satellite  
IN  
S-VIDEO  
OUT  
TV lower back panel  
Satellite receiver with component video  
You will need:  
coaxial cables  
To view satellite programs using the component video  
connections:  
Turn on the satellite receiver. Select the ColorStream HD-2  
standard A/V cables  
video input source on the TV.*  
– For better picture performance, if your VCR has S-video,  
use an S-video cable (plus the audio cables) instead of  
the standard video cable. Do not connect both types of  
video cable to VIDEO 1 at the same time or the picture  
performance will be unacceptable.  
To view the VCR or view and record antenna  
channels:  
Turn ON the VCR. Tune the VCR to the channel you want to  
watch. Select the VIDEO 1 video input source on the TV.*  
– If you have a mono VCR, connect L/MONO on the TV to  
your VCR’s audio out terminal using the white audio cable  
only.  
To record a TV program while watching a DVD:  
Turn ON the VCR. Tune the VCR to the channel to record.  
Select the ColorStream HD-1 video input source on the TV*  
to view the DVD.  
standard audio cables  
component video cables  
– You can connect the component video cables (plus audio  
cables) from the DVD player or satellite receiver to either  
set of ColorStream terminals on the TV (HD-1 or HD-2).  
The ColorStream HD-1 and HD-2 terminals can be used  
with Progressive (480p, 720p) and Interlaced (480i, 1080i)  
scan systems. A 1080i signal will provide the best picture  
performance (1080p is not supported).  
– If your DVD player or satellite receiver does not have  
component video, connect a standard A/V cable to  
VIDEO 2 on the side panel. If your DVD player has HDMI  
video, see page 20.  
* To select the video input source, press INPUT on the remote control  
(- page 24). To program the TV remote control to operate other  
devices, see Chapter 3.  
The unauthorized recording, use, distribution, or revision of  
television programs, videotapes, DVDs, and other materials is  
prohibited under the Copyright Laws of the United States and  
other countries, and may subject you to civil and criminal  
liability.  
To view antenna or Cable channels:  
Select the ANT video input source on the TV.*  
To view the DVD player:  
Turn ON the DVD player. Select the ColorStream HD-1  
video input source on the TV.*  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
Connecting a camcorder  
You will need:  
standard A/V cables  
– For better picture performance, if your camcorder has  
S-video, connect an S-video cable (plus the audio cables)  
to VIDEO 1 on the TV back instead of the VIDEO 2 on the  
TV right side panel.  
Camcorder  
VIDEO AUDIO  
OUT  
L
R
VIDEO 2 inputs on TV right side panel  
To view the camcorder video:  
Select the VIDEO 2 video input source on the TV.*  
* To select the video input source, press INPUT on the remote control  
(- page 24). To program the TV remote control to operate other  
devices, see Chapter 3.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
To connect a DVI device, you will need:  
one HDMI-to-DVI adapter cable (HDMI type A connector)  
per DVI device  
– For proper operation, the length of an HDMI-to-DVI  
adapter cable should not exceed 9.8 ft (3m). The  
recommended length is 6.6 ft (2m).  
Connecting an HDMIor DVI device  
to the HDMI input  
The HDMI input on your TV receives digital audio and  
uncompressed digital video from an HDMI source device, or  
uncompressed digital video from a DVI (Digital Visual  
Interface) source device.  
This input is designed to accept HDCP (High-Bandwidth  
Digital-Content Protection) program material in digital form  
from EIA/CEA-861-861B–compliant[1] consumer electronic  
devices (such as a set-top box or DVD player with HDMI or  
DVI output).  
one pair of standard analog audio cables per DVI device  
– An HDMI-to-DVI adapter cable transfers video only.  
Separate analog audio cables are required (see  
illustration).  
– See “Setting the HDMIaudio mode” (- page 35).  
TV lower back panel  
TV upper back panel  
The HDMI input can accept and display VGA, 480i (60Hz),  
480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/  
60Hz) signal formats. For detailed signal specifications, see  
page 72.  
Supported Audio format: Linear PCM, sampling rate 32/44.1/  
48 kHz  
Note: To connect a PC to the HDMI input, see page 22.  
To connect an HDMI device, you will need:  
one HDMI cable (type A connector) per HDMI device  
DVI device  
DVI/HDCP  
OUT  
VIDEO  
AUDIO  
– For proper operation, it is recommended that you use an  
L
L
R
IN  
HDMI cable with the HDMI Logo (  
).  
– To display an 1080p/60Hz signal format, you will need a  
Category 2 cable. Conventional HDMI/DVI cable may not  
work properly.  
– HDMI cable transfers both video and audio. Separate  
analog audio cables are not required (see illustration).  
– See “Setting the HDMIaudio mode” (- page 35).  
OUT  
R
Note: To ensure that the HDMI or DVI device is reset properly,  
it is recommended that you follow these procedures:  
When turning on your electronic components, turn on the  
TV first, and then the HDMI or DVI device.  
TV lower back panel  
When turning off your electronic components, turn off the  
HDMI or DVI device first, and then the TV.  
[1] EIA/CEA-861-861B compliance covers the transmission of  
uncompressed digital video with high-bandwidth digital content  
protection, which is being standardized for reception of high-  
definition video signals. Because this is an evolving technology, it  
is possible that some devices may not operate properly with the TV.  
HDMI device  
VIDEO  
AUDIO  
HDMI OUT  
L
R
IN  
OUT  
HDMI, the HDMI logo and High-Definition Multimedia Interface are  
trademarks or registered trademarks of HDMI Licensing LLC.  
R
L
To view the HDMI device video:  
Select the HDMI 1, HDMI 2, or HDMI 3 video input source on  
the TV.*  
* To select the video input source, press INPUT on the remote control  
(- page 24). To program the TV remote control to operate other  
devices, see Chapter 3.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
Note:  
Some audio systems may not be compatible with Dolby  
Connecting a digital audio system  
Digital bitstream signals. Older audio systems that are not  
compatible with standard optical out signals may not work  
properly, creating a high noise level that may damage  
speakers or headphones. THIS DAMAGE IS NOT COVERED  
BY YOUR WARRANTY.  
The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby®*  
Digital g or 2-channel down-mixed PCM (pulse-code  
modulation) signal for use with an external Dolby® Digital  
decoder or other external audio system with optical audio  
input.  
The DIGITAL AUDIO OUT terminal may not output some  
digital audio sources because of copy restrictions.  
You will need:  
* Manufactured under license from Dolby Laboratories.  
Dolby, and the double-D symbol are registered trademarks of Dolby  
Laboratories.  
optical audio cable (Use an optical audio cable that has the  
larger “TosLink” connector and not the smaller “mini-  
optical” connector.)  
Dolby Digital decoder or  
other digital audio system  
Connecting an audio system  
Optical  
Audio IN  
LINE IN  
This connection allows you to use external speakers with an  
external analog audio amplifier to adjust the sound level.  
L
R
TV lower back panel  
You will need:  
standard audio cables  
Analog audio amplifier  
LINE IN  
L
R
To control the audio:  
1
2
Turn on the TV and the digital audio device.  
TV upper back panel  
Press Y on the TV’s remote control and open the Audio  
menu.  
3
Highlight Audio Setup and press T.  
Audio  
Digital Audio Selector  
Audio Settings  
Advanced Audio Settings  
Audio Setup  
To control the audio:  
4
In the Optical Output Format field, select either  
Dolby Digital/Surround or PCM, depending on your  
device  
(- “Selecting the optical audio output format” on  
page 49).  
1
2
Turn on the TV and the stereo amplifier.  
Minimize the sound volume from the TV’s built-in  
speakers and control the volume level using the  
amplifier’s remote control.  
Audio Setup  
PC Audio  
No  
Auto  
HDMI 1 Audio  
MTS  
Stereo  
Language  
English  
Optical Output Format  
Dolby Digital/Surround  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
DVD Audio  
Reset  
Done  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2: Connecting your TV  
Depending on the DVD’s title and the specifications of the  
PC on which you are playing the DVD-Video, some scenes  
may be skipped or you may not be able to pause during  
multi-angle scenes.  
Connecting a personal computer  
(PC)  
Signal names for mini D-sub 15-pin connector  
With either the PC IN or HDMI connection, you can watch  
your computer’s display on the TV and hear the sound from the  
TV’s speakers.  
Signal  
name  
R
Signal  
name  
Ground 11  
Ground 12  
Ground 13  
Signal  
name  
NC  
Pin No.  
Pin No.  
Pin No.  
1
2
3
4
5
6
G
7
NC  
To connect a PC to the PC IN terminal on the TV:  
When connecting a PC to the PC IN terminal on the TV, use an  
analog RGB (15-pin) computer cable and a PC audio cable.  
B
8
H-sync  
V-sync  
NC  
NC *  
NC  
9
NC  
14  
TV lower back panel  
10  
Ground 15  
TV upper back panel  
*NC=Not connected  
To connect a PC to the HDMI terminal on the TV:  
When connecting a PC to the HDMI terminal on the TV, use  
an HDMI-to DVI adapter cable and analog audio cables.  
If connecting a PC with an HDMI terminal, use an HDMI cable  
(type A connector). Separate analog cables are not necessary  
(- page 20).  
TV upper back panel  
PC audio  
cable  
TV lower back panel  
Computer  
PC audio  
output  
PC audio  
cable  
Conversion adapter  
(if necessary)  
Computer  
To use a PC, set the monitor output resolution on the PC  
before connecting it to the TV. The following signals can be  
displayed:  
PC audio  
output  
Format  
VGA  
Resolution  
640 × 480  
800 × 600  
1024 × 768  
V. Frequency  
60Hz  
SVGA  
XGA  
60Hz  
60Hz  
The HDMI input can accept and display VGA, 480i (60Hz),  
480p (60Hz), 720p (60Hz), 1080i (60Hz), and 1080p (24Hz/  
60Hz) signal formats. For detailed signal specifications, see  
page 72.  
Other formats or non-standard signals will not be displayed  
correctly.  
To display the optimum picture, use the PC setting feature  
(- “Using the PC settings feature” on page 54).  
Note:  
Note:  
The edges of the images may be hidden.  
The PC audio input terminals on the TV are shared with the  
HDMI-1 analog audio input terminals (- page 55).  
Some PC models cannot be connected to this TV.  
If receiving a 720p, 1080i, or 1080p signal program, Native  
mode scales the video to display the entire picture within the  
borders of the screen (i.e. no overscanning).  
An adapter is not needed for computers with a compatible  
mini D-sub15-pin terminal.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
Always remove batteries from the remote control if they are  
dead or if the remote control is not to be used for an  
extended period of time. This will prevent battery acid from  
leaking into the battery compartment.  
Preparing the remote control  
for use  
Your TV remote control can operate your TV and many other  
devices such as cable converter boxes, satellite receivers,  
VCRs, DVD players, and HTIBs (home theater in a box), even  
if they are different brands.  
Remote control effective range  
For optimum performance, aim the remote control directly at  
the TV and make sure there is no obstruction between the  
remote control and the TV.  
If you have a Toshiba device:  
Your TV remote control is preprogrammed to operate most  
Toshiba devices (- page 27).  
If you have a non-Toshiba device or a Toshiba device  
that the remote control is not preprogrammed to  
operate:  
Point remote control  
toward remote sensor  
on front of TV.  
You can program the TV remote control so it will operate the  
other device (- pages 25–29).  
Installing the remote control  
batteries  
16.4 ft (5m)  
1
Remove the battery cover from the back of the remote  
control.  
Squeeze tab  
and lift cover.  
2
Install two “AAA” size batteries, making sure to match  
the + and – signs on the batteries to the signs on the battery  
compartment.  
3
Reinsert the battery cover in the remote control until the  
tab snaps.  
Caution: Never throw batteries into a fire.  
Note:  
Be sure to use AAA size batteries.  
Dispose of batteries in a designated disposal area.  
Batteries should always be disposed of with the  
environment in mind. Always dispose of batteries in  
accordance with applicable laws and regulations.  
If the remote control does not operate correctly, or if the  
operating range becomes reduced, replace batteries with  
new ones.  
When necessary to replace batteries in the remote control,  
always replace both batteries with new ones. Never mix  
battery types or use new and used batteries in combination.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
1
POWER turns the TV on and off. When the TV is on, the  
Learning about the remote control  
green LED indicator on the TV front will be illuminated.  
PIC MODE selects the picture mode (- page 45).  
SLEEP accesses the sleep timer (- page 55).  
2
3
4
The buttons used for operating the TV only are described here.  
For a complete list of the remote control’s functions, see the  
remote control functional key chart (- page 26).  
PIC SIZE cycles through the picture sizes: Natural,  
TheaterWide 1/2/3, Full, 4:3 HD, and Native (-  
page 42).  
5
Channel Numbers (0–9, –/100) directly tune  
channels. The = button is used to tune digital channels  
(- page 41) or to edit the Favorites List (- page 39).  
6
7
INPUT selects the video input source (- page 38).  
CH Bb cycles through programmed channels when no  
menu is on-screen (- page 33).  
8
VOL + – adjusts the volume level.  
9
FAV BROWSER accesses the Favorites List in the  
Channel Brower(- page 39).  
10 RECALL displays TV status information (- page 56).  
11 CH RTN returns to the last viewed channel or source  
(- page 41).  
12 MUTE reduces or turns off the sound (- page 47).  
13 INFO displays TV status information as well as program  
details, when available. (- page 56).  
14 3 C / # c While watching TV, these buttons open the  
Channel Browserand tune to the previous/next channel  
in the channel history (- page 40). (Also see “Arrow  
buttons.”)  
15 Arrow buttons (BbC c) When a menu is on-screen,  
these buttons select or adjust programming menus. (Also  
see 3 C / # c.)  
16 ENTER activates highlighted items in the main menu  
system.  
17 MENU accesses the main TV menu system (- pages 30  
and 31).  
18 EXIT closes on-screen menus.  
19 MODE SELECT switch switches between TV,  
CABLE/SAT, AUX 1, and AUX 2 modes (- page 25).  
Set to “TV” to control the TV.  
You can also control the built-in DVD when the MODE  
SELECT switch on the remote control is in TV mode. For  
DVD operation the following buttons are used:  
TOP MENU, DVD RTN, SET UP, DVD CLEAR,  
PAUSE, PLAY, STOP, SKIP, REW, FF, SEARCH,  
SLOW, ANGLE, SUB TITLE, AUDIO, and EJECT  
(- Chapter 8).  
Note: The error message “Not Available” may appear if you  
press a key for a function that is not available.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
1
2
POWER Turns the selected device on and off.  
Using the remote control to control  
your other devices  
Channel Numbers (0-9) Press to directly access  
channels (as opposed to < ,).  
3
4
5
+10 Press to directly access DVD chapters higher than 10.  
If you have a non-Toshiba device or a Toshiba device that the  
remote control is not preprogrammed to operate, you must first  
program the remote control to recognize the device (if you  
have not already done so) (- pages 27–29).  
TOP MENU Accesses a DVD’s top menu.  
CH Bb For channels programmed into the channel  
memory (- page 41):  
B selects the next higher channel.  
b selects the next lower channel.  
To use your TV remote control to operate a:  
Cable converter box or satellite receiver, set the MODE  
6
GUIDE Displays the channel guide in the CABLE/SAT  
SELECT switch to CABLE/SAT.  
mode.  
VCR, set the MODE SELECT switch to AUX 1.  
DVD player or HTIB, set the MODE SELECT switch to  
AUX 2.  
SET UP Accesses a DVD’s setup menu in the AUX  
mode.  
7
INFO Displays TV status information on-screen.  
Note: Even after the TV remote control is programmed, it may  
not operate certain features on any other devices. If this  
happens and you wish to use those features, you will need to  
use the device’s original remote control.  
8
BbC c Press to navigate DVD menus (may not work on  
some DVD players).  
9
ENTER Required by some satellite receivers and DVD  
players to activate certain functions.  
Point the remote control  
directly at the device.  
10 DVD CLEAR Press to reset the title and chapter number.  
11 PLAY Begins playback of a tape or DVD.  
12 PAUSE Press during play or record mode to pause the  
picture; press again to restart.  
13 STOP Stops the tape or DVD.  
14 SKIP z Skips forward to locate later DVD chapters.  
15 FF Fast-forwards the tape or DVD. (Press during play  
mode to view the picture moving rapidly forward.)  
16 SKIP Z Skips back to beginning of current DVD  
chapter, or locates previous chapters.  
17 REW Rewinds/reverses the tape or DVD. (Press during  
play mode to view the picture moving rapidly backward.)  
18 TV/VCR To view one program while recording another,  
press to select TV mode.  
SEARCH selects a specific DVD chapter, title or time.  
19 REC Starts tape recording.  
16  
17  
18  
19  
20 SLOW X Slow-forwards the DVD.  
21 SLOW x Slow-reverses the DVD.  
22 MODE SELECT switch Set to “TV” to control the TV;  
“CABLE/SAT” to control a cable converter box or  
satellite receiver; “AUX 1” to control a VCR; “AUX 2” to  
control a DVD player or HTIB.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
Remote Control functional key chart  
Note:  
“---” = key does not send a signal in that remote control mode.  
sTV” = key will affect the TV, even though the remote control is in another mode.  
* Not available for your TV.  
Toshiba TV/  
REMOTE CONTROL KEY  
CABLE  
SAT (satellite) AUX 1 (VCR)  
AUX 2 (DVD or HTIB)  
Built-in DVD  
Power  
POWER  
SLEEP  
PIC SIZE  
PIC MODE  
1-9  
Power  
s TV  
s TV  
s TV  
Digit 1-9  
Digit 0  
---  
Power  
Power  
s TV  
s TV  
s TV  
Digit 1-9  
Digit 0  
100  
Power  
s TV  
s TV  
s TV  
Digit 1-9  
Digit 0  
+10  
Sleep timer  
Picture size  
PIC MODE  
Digit 1-9  
s TV  
s TV  
s TV  
Digit 1-9  
Digit 0  
– (sub CH)  
s TV  
0
Digit 0  
100/–/+10  
INPUT  
– (sub CH)  
TV/Video select  
s TV  
s TV  
s TV  
FAV BROWSER/  
TOP MENU  
FAV BROWSER  
DVD TOP Menu  
---  
---  
---  
Top Menu  
MUTE  
Sound mute  
s TV  
---  
s TV  
s TV  
---  
s TV  
Setup  
SET UP/GUIDE  
VOL + –  
DVD setup  
SAT Guide  
s TV  
Volume up/down  
s TV  
s TV  
s TV  
Channel  
up/down  
Channel  
up/down  
Channel  
up/down  
Channel  
up/down  
CHBb  
---  
RECALL  
RECALL  
s TV  
s TV  
s TV  
s TV  
DVD Return  
Previous channel  
DVD previous menu  
CH RTN/DVD RTN  
---  
---  
---  
INFO  
Info  
---  
---  
Info  
---  
---  
Display  
Enter  
ENTER  
Enter  
Select, Enter  
Menu  
Bb  
Menu up/down  
---  
---  
---  
---  
Menu up/down  
Menu left  
up/down  
Menu left/  
C 3  
Menu left  
Channel Browser™  
Menu right/  
c #  
---  
---  
---  
Menu right  
Action Menu  
Exit  
---  
---  
---  
Menu right  
DVD Menu  
DVD Clear  
Channel Browser™  
MENU  
Menu  
Exit  
DVD clear  
EXIT/DVD CLEAR  
PAUSE/STEP  
PLAY  
Pause  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
Pause  
Play  
Pause  
Play  
Play  
STOP  
Stop  
Stop  
Stop  
SKIP Z  
SKIP z  
REW  
Skip REV  
Skip FWD  
Rewind  
Fast FWD  
---  
Skip REV  
Skip FWD  
Rewind  
Fast FWD  
---  
Rewind  
Fast FWD  
FF  
TV/VCR/  
SEARCH  
DVD search  
---  
---  
TV/VCR  
DVD search  
REC  
REC MENU*  
SLOW REW  
SLOW FWD  
Angle  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
---  
Record (2 click) ---  
SLOW –  
SLOW +  
ANGLE  
SUB TITLE  
AUDIO  
EJECT  
---  
---  
---  
---  
---  
---  
---  
---  
DVD Angle  
DVD Sub title  
DVD Audio  
DVD Eject  
Sub title  
Audio  
Eject  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
Programming the remote control  
to control your other devices  
Your Toshiba TV remote control is preprogrammed to operate  
most Toshiba devices. To program your TV remote control to  
operate a non-Toshiba device (or a Toshiba device that it is not  
preprogrammed to operate), follow the steps below. For details  
on using the remote control to operate the device, see page 25.  
1
2
In the remote control code table (- page 28), find the  
code for your device. If more than one code is listed, try  
each one separately until you find one that works.  
Set the MODE SELECT switch to the type of device  
you are programming the remote control to operate —  
CABLE/SAT (for a cable converter box or satellite  
receiver), AUX 1 (for a VCR or TV/VCR combo), or  
AUX 2 (for a DVD player or HTIB [home theater in a  
box]).  
3
4
While holding down E, press the Channel Number  
buttons to enter the 3-digit code for your device.  
To test the code, turn on the device, point the remote  
control at it, and press p. See notes below.  
If the correct code was entered, the device will turn off.  
If the device does not respond, repeat steps 1–4 using  
another code.  
If the device does not respond to another code, you will  
need to use the remote control that came with the  
device.  
5
6
Remember to set the MODE SELECT switch back to  
“TV” to control the TV.  
For future reference, write down the code(s) you used:  
DEVICE  
CODE  
DEVICE  
CODE  
Note:  
In addition to POWER, confirm that all necessary keys on the  
TV remote control operate your device. If some keys are not  
operational, repeat the device code setup using another  
code (if other codes are listed for your device). If, after trying  
all listed codes, the necessary keys do not operate your  
device, use the device’s original remote control.  
Every time you change the batteries, you will need to  
reprogram the remote control.  
Some newer VCRs respond to either of two codes. These  
VCRs have a switch labeled “VCR1/VCR2.” If your VCR has  
this kind of switch and does not respond to the codes for  
your VCR brand, set the switch to the other position (“VCR1”  
or “VCR2”) and reprogram the remote control.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
Drake  
020, 040, 044, 046,  
050, 053  
018, 041, 051  
057  
Clarion  
Classic  
Daewoo  
Denon  
Emerson  
Fisher  
Funai  
GE  
Go Video  
GPX  
019  
020  
021  
Remote control codes  
Echostar  
Express Vu  
Fujitsu  
022, 023, 024, 025  
026, 027  
028  
027  
001, 029, 030  
087  
031  
027  
In some cases you may not be able to  
operate your device with the TV  
remote control. Your other device may  
use a code that is not recognized by the  
TV remote control. If this happens, use  
the device’s remote control.  
GE  
008, 009, 013  
010, 011, 012, 022,  
023, 031, 049  
033  
General Instruments  
Hitachi  
Hughes  
033  
Hughes Network  
Systems  
Intersat  
Janeil  
JVC  
Hitachi  
005, 032, 033, 034,  
035  
003, 007, 036, 042,  
088  
037  
008, 009  
004, 038  
039  
040  
026  
041  
043  
044  
058  
010, 045, 046, 047,  
048, 049, 050  
004, 051  
052, 053, 054, 055  
001, 056  
057, 058  
001, 002, 059, 089  
060  
061, 062, 086, 090  
073  
063, 091  
064, 067  
074  
019  
048  
027  
017, 057  
029  
060  
058  
036, 052  
JVC  
Cable converter box  
Kenwood  
Konka  
Magnavox  
Memorex  
Mintek  
ABC  
061, 062, 063, 082,  
084, 087, 092, 096,  
098  
Kenwood  
Magnavox  
Optimus  
Pansat  
Primestar  
Proscan  
Radio Shack  
RCA  
Realistic  
Samsung  
Sony  
Star Choice  
Star Trak  
STS  
Archer  
065, 092, 097, 099  
064, 094  
092  
090, 092, 097  
083, 085, 086, 088,  
093, 098  
Cableview  
Century  
Citizen  
015, 042  
NAD  
008, 009, 013  
022, 023, 030  
008, 009, 013, 016  
030  
059  
014, 055  
057, 106  
025, 026, 037, 054  
024  
000, 001, 002, 003,  
004, 005, 006, 007,  
020, 031, 056  
021, 028, 030, 032,  
035, 039, 043, 045,  
047, 058  
Nakamichi  
Norcent  
Onkyo  
Oritron  
Panasonic  
Contec  
Diamond  
GE  
093  
061, 062  
Gemini  
Hamlin  
069, 070, 094  
093  
Philips  
Pioneer  
Proscan  
Qwestar  
RCA  
Sampo  
Samsung  
Sansui  
Sanyo  
Hitachi  
Jasco  
062, 095, 096  
097  
Toshiba  
Motorola/GI/Jerrold  
062, 069, 071, 082,  
086, 089, 096, 107  
072, 096  
092, 104  
090  
101  
081, 083, 085  
087  
Magnavox  
Memorex  
Multi Canal  
Novavision  
Panasonic  
Philco  
Uniden  
Zenith  
027  
Sharp  
Sherwood  
Sony  
011, 012, 065, 066,  
068, 069, 070  
027  
071  
072  
Philips  
066, 067, 068, 070,  
072, 073, 074, 075,  
092  
TV/VCR Combo  
Action  
Sylvania  
Teac  
Technics  
Techwood  
Toshiba  
078  
059, 062  
065  
065  
078  
065  
079  
074  
057  
GE  
Pioneer  
076, 077  
Goldstar  
Panasonic  
Precision  
Quasar  
Realistic  
Sony  
Toshiba  
Zenith  
Totevision  
Proscan  
061, 062  
075  
Radio Shack  
RCA  
092, 097, 099  
064, 081  
000, 013, 076, 077,  
078  
079, 080, 081  
014, 082, 092  
Realistic  
065  
Yamaha  
Zenith  
Recoton  
102  
Samsung  
Scientific Atlanta  
077, 090  
063, 078, 079, 080,  
088, 098, 101, 105  
095  
065  
009, 010, 065  
Portable DVD player  
Aiwa  
Audiovox  
Panasonic  
RCA  
Sears  
093  
Signature  
Signature 2000  
Sprucer  
062  
096  
081, 085  
094, 095  
024, 096, 099  
098  
DVD/VCR Combo  
Go Video  
DVD=087,  
VCR=081  
DVD=088,  
VCR=082  
DVD=089,  
VCR=083  
DVD=090,  
VCR=084  
DVD=091,  
VCR=085  
DVD=092,  
VCR=086  
Starcom  
069, 082, 087, 096,  
103, 104  
JVC  
Stargate  
069, 090  
VCR  
Admiral  
Aiko  
Aiwa  
Akai  
Sylvania  
095, 100  
RCA  
049  
019  
018  
TeleView  
Texscan  
090  
100  
Samsung  
Sanyo  
Zenith  
Tocom  
071, 084, 085  
087, 096, 098  
082  
065, 092, 097, 099,  
102, 103  
003, 004, 037, 038,  
039, 058, 069  
010  
007, 068  
008, 017  
U. S. Electronics  
United Cable  
Universal  
Audiovox  
Bell & Howell  
Broksonic  
Calix  
Wards  
096  
010  
Carver  
CCE  
Citizen  
026  
019  
DVD player  
Aiwa  
Apex  
BOSE  
Broksonic  
Satellite receiver  
Alphastar  
Chaparral  
DISH Network  
009, 010, 011, 012,  
013, 014, 015, 019,  
057, 073  
006, 015  
016, 017  
097  
038, 059  
034  
057  
Colortyme  
005  
018  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3: Using the remote control  
Video Concepts  
Wards  
005, 006, 011, 012,  
039, 053  
Orion  
054, 057, 062, 065,  
068, 072  
Craig  
009, 010, 016, 061,  
065, 079  
001, 005, 009, 012,  
014, 040, 048, 053,  
056, 057  
011, 013, 015, 017,  
018, 019, 057, 078  
078  
009, 010, 011, 016,  
018, 020, 024, 025,  
031, 035, 049, 051,  
056, 057, 060, 065,  
066, 079  
Panasonic  
Pentax  
036, 045, 046, 057,  
061, 072, 079  
012, 024, 025, 035,  
042, 053, 063  
014  
026, 027, 063  
026, 031, 044, 057  
006, 024, 043, 055  
012, 013, 015  
001, 002, 048  
061  
Curtis Mathes  
Daewoo  
Pentex Research  
Philco  
Philips  
Pioneer  
Portland  
Proscan  
Proton  
Quasar  
Radio Shack  
Radio Shack/Realistic  
White Westinghouse  
XR-1000  
Yamaha  
073  
018  
Daytron  
Denon  
Dimensia  
Electrohome  
Emerson  
063  
001, 048  
005, 006, 007, 014,  
037, 053  
004, 032, 034, 041,  
047, 069, 086  
010, 020, 065  
003, 008, 010, 011,  
017, 018, 020, 028,  
039, 054, 057, 062,  
065, 068, 072  
007, 016, 021, 022,  
023, 057, 064, 068,  
070, 071, 079  
004, 041  
Zenith  
045  
010, 031, 065  
007, 009, 010, 016,  
018, 020, 021, 022,  
031, 049  
HTIB  
Lasonic  
Panasonic  
Venturer  
Fisher  
083  
084  
085  
Radix  
RCA  
010  
Fuji  
001, 002, 003, 009,  
024, 025, 029, 035,  
040, 042, 045, 048,  
055, 056, 063, 071,  
083  
007, 009, 010, 011,  
016, 018, 020, 021,  
022, 031, 049, 051,  
056, 060, 065, 075,  
079  
Funai  
Garrard  
GE  
018, 073  
018  
001, 002, 009, 040,  
042, 048, 056  
056, 059, 061, 081  
005, 010, 014, 054,  
056, 065, 067  
018, 065  
Go Video  
Goldstar  
Realistic  
Gradiente  
Harman Kardon  
Hitachi  
005  
024, 025, 035, 037,  
042, 063, 070, 080  
076  
Ricoh  
Runco  
047  
034  
JBL  
Samsung  
009, 011, 038, 056,  
073, 084  
006, 037, 043, 061  
007, 009, 016, 054,  
064, 068, 071, 075,  
079, 085  
008, 011, 017, 028,  
030, 057, 065, 072  
007, 010, 016, 021,  
022, 023, 024, 025,  
035, 053, 057, 063,  
064, 065, 068, 071,  
075, 079  
JC Penney  
005, 006, 007, 008,  
009, 010, 023, 024,  
025, 026, 035, 056,  
061, 063, 065  
024, 025, 037, 050  
005, 006, 007, 014,  
037, 043, 055, 062,  
063, 068, 082  
005, 006, 007, 012,  
014, 037, 043, 050,  
053, 068, 071  
010  
Sansui  
Sanyo  
Jensen  
JVC  
Scott  
Sears  
Kenwood  
Kodak  
LG  
010  
Sharp  
013, 020, 031, 049,  
051, 060, 066  
004, 025, 032, 061  
049  
075  
047, 061  
004, 032, 033, 041,  
052, 058, 070, 074,  
076, 077, 080  
035  
018, 026, 027, 028,  
044, 072  
Lloyds  
Logik  
LXI  
Magnasonic  
Magnavox  
053, 073, 079  
061  
010  
Shintom  
Signature  
Signature 2000  
Singer  
061, 065, 078  
026, 027, 034, 044,  
057, 061, 072  
005, 006, 007, 012,  
014, 026, 053, 067  
007, 009, 010, 016,  
018, 034, 049, 063,  
065, 066, 068, 075,  
079  
Sony  
Marantz  
Memorex  
STS  
Sylvania  
Symphonic  
018, 050, 051, 053,  
073, 079  
MGA  
MGN  
020, 028, 039  
056  
Tandy  
007  
010  
037  
018, 029, 037  
036  
010, 018, 065  
000, 011, 021, 023,  
024, 028, 030, 039,  
057, 074, 078, 079  
009, 010, 065  
073  
Minolta  
Mitsubishi  
024, 025, 035, 063  
020, 024, 025, 028,  
039, 043, 065  
049  
Tashiko  
Tatung  
Teac  
Technics  
Teknika  
Toshiba  
Montgomery Ward  
Motorola  
MTC  
Multitech  
NEC  
049  
009, 046, 061  
009, 012, 018  
005, 006, 007, 012,  
014, 037, 043, 053,  
054, 067, 070  
010  
Totevision  
Unitec  
Nikko  
Unitech  
Vector Research  
009  
Noblex  
Optimus  
Optonica  
009  
010, 049, 065  
031  
005, 006, 011, 012,  
053  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Menu layout and navigation  
Main menu layout  
The tables below and on the next page provide a quick overview of your TV’s menu system.  
To open the main menus (illustrated below), press Y on the remote control or TV control panel.  
Icon  
Item  
Option  
Mode  
S Sports/Standard/Movie/Preference  
S [Opens the Picture Settings menu]  
S [Opens the Noise Reduction menu]  
S On/Off  
Video  
Picture Settings  
Noise Reduction  
Game Mode  
Theater Settings  
Digital Audio Selector  
Audio Settings  
Advanced Audio Settings  
Audio Setup  
S [Opens the Theater Settings menu]  
S [Launches the temporary Audio Selector]  
S [Opens the Audio Settings menu]  
S [Opens the Advanced Audio Settings menu]  
S [Opens the Audio Setup menu]  
S [Launches the temporary CC Selector]  
S Off/CC1/CC2/CC3/CC4/T1/T2/T3/T4  
S [Opens the Digital CC Setup menu]  
S [Opens the Input Labeling menu]  
S [Opens the Channel Labeling menu]  
S English/French/Spanish  
Audio  
CC Selector  
Preferences  
Base CC Mode  
Digital CC Settings  
Input Labeling  
Channel Labeling  
Menu Language  
Channel Browser Setup  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
S [Opens the Channel Browser Setup menu]  
S Off/On  
Locks  
S [Opens the Edit Rating Limits menu]  
S [Opens the Channels block menu]  
S Off/Video/Video+  
Front Panel Lock  
New PIN Code  
Installation  
S Off/On  
S [Opens the New PIN Code entry screen]  
S [Opens the Installation menu (- page 31)]  
S [Opens the Sleep Timer menu]  
S [Opens the PC Settings menu]  
Setup  
Sleep Timer  
PC Settings  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4: Menu layout and navigation  
Setup/Installation menu layout  
The Installation menu contains the Terrestrial and System Status menus.  
To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu,  
select Installation, and press T.  
Icon  
Item  
Option  
Press Y,  
open the  
Setup menu,  
and then  
Input Configuration  
Channel Program  
Channel Add/Delete  
Signal Meter  
S [Opens the Input Configuration menu]  
S [Start] S [Scans for new channels on ANT]  
S [Opens the Channel Add/Delete menu]  
S [Opens the Signal Meter menu]  
Terrestrial  
open the  
Installation  
sub-menu.  
System Status  
System Information  
S [Opens the System Information screen]  
Note:  
The menu background may sometimes appear black,  
depending on the signal the TV is receiving. This is not a  
sign of malfunction.  
Navigating the menu system  
You can use the buttons on the remote control or TV control  
panel to access and navigate your TV’s on-screen menu  
system.  
Video  
Press Y to open the menu system.  
Mode  
Sports  
Off  
Picture Settings  
Noise Reduction  
Game Mode  
When a menu is open, use the up/down/left/right arrow  
buttons (BbC c) on the remote control or TV control panel  
to move in the corresponding direction in the menu.  
Theater Settings  
Press T to save your menu settings or select a highlighted  
item. (A highlighted menu item appears in a different color  
in the menu.)  
All menus close automatically if you do not make a selection  
within 60 seconds, except the signal meter menu, which  
closes automatically after about 5 minutes.  
Navigate  
ENTER  
CH RTN  
Back  
EXIT Exit  
Select  
The Video sub-menu appears with a black background,  
which looks different from other menus.  
Picture Settings  
Mode: Sports  
Contrast  
Back Light  
DynaLight  
Brightness  
Color  
100  
100  
To close a menu instantly, press O.  
On  
50  
50  
0
Tint  
Sharpness  
50  
Advanced Picture Settings  
Reset  
Done  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Setting up your TV  
Selecting the menu language  
Configuring the antenna input  
source for the ANT terminal  
You can choose from three different languages (English,  
French and Spanish) for the on-screen display of menus and  
messages.  
To configure the ANT input source:  
To select the menu language:  
1
2
Press Y and open the Setup menu.  
Highlight Installation and press T.  
1
2
3
Press Y and open the Preferences menu.  
Highlight Menu Language and press c.  
Press B or b to select your preferred menu language and  
press T.  
Setup  
Installation  
Sleep Timer  
PC Settings  
Preferences  
3
(A new set of Installation menu icons will appear, as  
shown below.) Open the Terrestrial menu, highlight  
Input Configuration, and press T.  
CC Selector  
Base CC Mode  
Off  
Digital CC Settings  
Input Labeling  
Channel Labeling  
Menu Language  
Channel Browser Setup  
Installation  
English  
Français  
Español  
English  
Terrestrial  
Input Configuration  
Channel Program  
Channel Add/Delete  
Signal Meter  
4
Press O to close the Preferences menu.  
4
5
Press C or c to select the input source (Cable or  
Antenna) for the ANT input on the TV.  
Input Configuration  
Antenna In  
Cable  
Done  
Cancel  
To save your new settings, highlight Done and press T.  
To revert to your original settings, highlight Cancel and  
press T.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Setting up your TV  
4
(A new set of Installation menu icons will appear, as  
Programming channels into the  
TV’s channel memory  
shown below.) Open the Terrestrial menu, highlight  
Channel Program to bring up the Start, and press T  
again to begin channel programming.  
When you press < or , on the remote control or TV control  
panel, your TV will stop only on the channels you programmed  
into the TV’s channel memory.  
Follow the steps below to program channels into the TV’s  
channel memory.  
Installation  
Terrestrial  
Input Configuration  
Start  
Channel Program  
Channel Add/Delete  
Signal Meter  
Programming channels automatically  
ANT  
Cable  
Your TV can automatically detect all active channels in your  
area and store them in its memory. After the channels are  
programmed automatically, you can manually add or erase  
individual channels in the channel memory.  
Scanning channels, please wait ...  
52%  
Number of Channels Found - 73  
Scanning Digital Channels  
Found Channel - 118  
Abort  
Note:  
You must configure the antenna input source before  
The TV will automatically cycle through all the antenna  
channels, and store all active channels in the channel  
memory. While the TV is cycling through the channels,  
the message “Scanning channels, please wait” appears (as  
shown above).  
programming channels (- page 32).  
If the Antenna input signal type is set to Cable, the automatic  
channel programming process erases channels that were  
previously programmed into the TV’s memory.  
If the Antenna input signal type is set to Antenna, the  
automatic channel programming process adds newly found  
channels to the existing set of programmed channels (and  
does NOT erase channels that were previously  
programmed into the TV’s memory.) To remove an Antenna  
source channel from the memory, you must manually delete  
it.  
5
To cancel channel programming, press O on the remote  
control (or highlight Abort in the on-screen display and  
press T).  
When channel programming is finished, press < or , to  
view the programmed channels.  
To tune the TV to a channel not programmed in the channel  
memory, you must use the Channel Number buttons on the  
remote control.  
Programming channels when the antenna input is  
configured for Cable will take substantially longer than when  
the antenna input is configured for Antenna. This is normal;  
however, once channel programming is finished, you should  
not have to repeat the programming process again unless  
your Cable TV service lineup changes significantly.  
Manually adding and deleting channels  
in the channel memory  
After automatically programming channels into the channel  
memory, you can manually add or delete individual channels.  
To add or delete channels in the channel memory:  
1
2
3
Press Y and open the Setup menu.  
To program channels automatically:  
Highlight Installation and press T.  
(A new set of Installation menu icons will appear, as  
shown below.) Open the Terrestrial menu, highlight  
Channel Add/Delete, and then press T.  
1
Configure the antenna input source, if you have not  
already done so (- page 32).  
2
3
Press Y and open the Setup menu.  
Highlight Installation and press T.  
Installation  
Terrestrial  
Input Configuration  
Channel Program  
Channel Add/Delete  
Signal Meter  
Setup  
Installation  
Sleep Timer  
PC Settings  
(continued)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Setting up your TV  
To add a channel to the channel memory:  
Highlight the unchecked box next to the channel number you  
want to add, and then press T to check the box.  
Labeling channels  
A list of common channel labels (logos) for various channels  
(ABC, CBS, etc.) will be programmed into the TV. You will  
be able to view and assign these logos from the Channel  
Labeling window. If the desired channel label is not provided  
in the list, you will be able to manually enter/edit labels using  
the software keyboard.  
To manually add digital subchannels on a physical  
channel:  
Use the Channel Numbers and the Dash (=) on the remote  
control to enter the channel number (for example, 56–1).  
If the channel is found, the number will be added to the list and  
the box will be checked.  
To assign channel labels:  
If the channel is not found, a message will appear.  
1
2
Press Y and open the Preferences menu.  
To remove a channel from the channel memory:  
Highlight the checked box next to the channel number you  
want to remove, and then press T to uncheck the box.  
Highlight Channel Labeling and press T.  
The Channel Labeling window opens.  
To save your new settings:  
Highlight Done and press T.  
Preferences  
CC Selector  
Base CC Mode  
Off  
To revert to your original settings:  
Highlight Cancel and press T before saving.  
Digital CC Settings  
Input Labeling  
Channel Labeling  
Menu Language  
Channel Browser Setup  
English  
To remove all channels from the channel memory:  
Highlight Reset and press T, and then highlight Done and  
press T.  
Channel Labeling  
{No Label}  
ANT  
Channel Add/Delete  
A&E  
24  
A&E  
Press CH UP/DOWN to  
change channels.  
Analog  
Digital  
Digital  
Analog  
Analog  
Digital  
Analog  
Analog  
Digital  
Analog  
2
2 - 1  
2 - 2  
3
ABC  
ABCFAM  
ABCHD  
AMAX  
AMAXW  
AMC  
Custom  
Clear All  
Done  
4
5
ANIMAL  
6
7
Reset  
Cancel  
Done  
3
4
Press < or , to select the channel you want to label.  
7 - 1  
8
Press BbC c to highlight the desired channel label and  
press T.  
To remove encrypted channels from the channel  
memory:  
If an encrypted channel is accidentally added to the channel list  
by programming channels, you can remove the unwanted  
encrypted (non-viewable) channel while you are channel  
surfing. When you tune to an encrypted channel, the following  
message will appear.  
5
6
Repeat steps 3 and 4 for other channels.  
To save your settings, highlight Done and press T.  
Channel Labeling  
{No Label}  
ANT  
A&E  
24  
A&E  
Press CH UP/DOWN to  
change channels.  
ABC  
ABCFAM  
ABCHD  
AMAX  
Digital Channel Is Encrypted - Press 1 on remote to remove channel  
AMAXW  
AMC  
Custom  
Clear All  
Done  
ANIMAL  
Press “1” button while the message is on the screen to  
remove the unnecessary channel from the channel list.  
The maximum number of labels that can be stored is 128.  
To remove channel labels:  
1
2
Open the Channel Labeling window.  
Press < or , to select the channel for which you want to  
remove the label.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Setting up your TV  
3
Press BbC c to highlight No Label and press T.  
3
Highlight Yes from the deletion confirmation window  
and press T.  
Channel Labeling  
{No Label}  
Channel Labeling  
ANT  
A&E  
24  
TIMES  
TLC  
ANT  
ABC  
ABCFAM  
ABCHD  
AMAX  
24  
Press CH UP/DOWN to  
change channels.  
TMC  
TMCX  
TMCXw  
TMCw  
Delete the selected custom label?  
No  
Yes  
AMAXW  
AMC  
Custom  
Clear All  
Done  
TNT  
Custom  
Clear All  
Done  
ANIMAL  
TNTHD  
TOCDEFG  
4
5
Repeat steps 2 and 3 for other channels.  
4
Highlight Done and press T to save changes, and go  
back to the Channel Labeling window.  
To save your settings, highlight Done and press T.  
If the desired channel label is not available from the list of  
presets, you can create a custom label.  
Setting the HDMIaudio mode  
To create and assign a custom label:  
To set the HDMI audio mode:  
1
2
3
Open the Channel Labeling window.  
Press < or , to select a channel you want to label.  
1
2
3
Press Y and open the Audio menu.  
Press Bb c to highlight Custom and press T.  
The software keyboard will appear.  
Highlight Audio Setup and press T.  
Press B or b to select HDMI 1 Audio and then press C  
or c to select the HDMI 1 audio mode (Auto, Digital, or  
Analog). (Auto is the recommended mode.) See  
“Connecting an HDMI or DVI device to the HDMI input”  
(- page 20).  
Channel Labeling  
{No Label}  
ANT  
A&E  
24  
2
3
6
9
AB
1
4
5
ABC
7
8
0
ABC
_
INPUT
100  
AM
Audio Setup  
AMAXW  
AMC  
PC Audio  
No  
Auto  
Clear All  
Done  
ANIMAL  
HDMI 1 Audio  
MTS  
Stereo  
4
Repeatedly press the corresponding key on the remote  
control to highlight the desired character on the on-screen  
software keyboard.  
Language  
English  
Optical Output Format  
Dolby Digital/Surround  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
5
6
The highlighted character is entered after you either press  
a different key, press c key, or after a two-second pause.  
DVD Audio  
Reset  
Done  
Repeat steps 4 and 5 until you have entered all desired  
text.  
Note: Because the PC and HDMI-1 inputs share the same set  
of analog audio inputs, the PC Audio menu setting influences  
the HDMI 1 Audio menu setting. If PC Audio is set to “No,” the  
HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to  
Yes,” the HDMI 1 Audio setting is set to “Digital” and is  
grayed out in the menu. (Also see item 4 on page 14 and  
“Setting the PC Audio” on page 55.)  
7
8
When finished, press T.  
(New labels will be added to the list in alphabetical order  
and marked with an icon to indicate that they are  
custom.) Highlight the new custom label and press T to  
assign. Assigned channel labels will be displayed in the  
banner, Channel Add/Delete window, and Channels  
Block window.  
To delete the custom label:  
1
2
Open the Channel Labeling window.  
Highlight the label to be deleted and press =.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Setting up your TV  
Viewing the digital signal meter  
Viewing the system status  
You can view the digital signal meter in the ANT digital TV  
input source only.  
To view the system status:  
1
2
3
Press Y and open the Setup menu.  
To view the digital signal meter:  
Highlight Installation and press T.  
1
2
3
Press Y and open the Setup menu.  
A new set of Installation menu icons will appear, as shown  
below. Open the System Status menu, highlight  
System Information, and press T.  
Highlight Installation and press T.  
A new set of Installation menu icons will appear, as shown  
below. Open the Terrestrial menu, highlight Signal  
Meter, and press T.  
Installation  
System Status  
System Information  
Installation  
Terrestrial  
4
Press C c to scroll through the menu bar to select the  
Software Version and view the related information.  
Input Configuration  
Channel Program  
Channel Add/Delete  
Signal Meter  
System Information  
Software Version  
LV07  
3.2.21.0  
Nov 17 2006 - 01:52:20  
FW: 0B  
4
Press BbC c to select the antenna input and digital  
channel whose signal you want to check.  
Note: The physical digital channel number listed in the  
Signal Meter screen may not correspond to a virtual TV  
channel number. Contact your local broadcasters to  
obtain the RF channel numbers for your local digital  
stations.  
Done  
To close the screen and return to the Installation  
menu:  
Highlight Done and press T.  
Signal Meter  
To return to normal viewing:  
Signal Locked  
Press O.  
0
Peak  
0
Physical Digital Channel  
Virtual Digital Channel  
4
4-1  
Advanced  
Done  
To close the screen and return to the Terrestrial  
menu:  
Highlight Done and press T.  
To return to normal viewing:  
Press O.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5: Setting up your TV  
Reset Factory Defaults  
To reset all settings and channels to their factory  
default values:  
1
2
Press Y and open the Setup menu.  
Highlight Installation and press T. A new set of  
Installation menu icons will appear.  
3
4
Open the System Status menu, highlight System  
Information, and press T.  
Press C c to scroll through the menu bar to select  
Factory Defaults.  
System Information  
Factory Defaults  
This window provides the ability to reset the TV  
settings.Type in your PIN now (or "0000" if no  
PIN has been set) to restore settings to their  
factory default values.  
Done  
5
6
Enter your PIN code (or 0000 if no PIN code has been set).  
Highlight Yes and press T. The TV will turn off  
automatically after a few seconds. After the TV turns off,  
unplug the TV power cord and then plug it in again to  
complete the reset process.  
System Information  
Press YES to confirm. After the TV  
turns off, unplug it and plug it back  
in to complete the reset.  
No  
Yes  
To cancel the reset:  
Highlight No and press T.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Selecting the video input source  
Labeling the video input sources  
to view  
You can label each video input source according to the type of  
device you connected to each source, from the following preset  
list of labels:  
To select the video input source to view:  
– – (default label)  
Audio Receiver  
Cable  
Compact Disc  
DTV  
DVD  
Game Console  
HD DVD  
1
2
Press + on the remote control or TV control panel.  
And then either:  
a) Press 0–9; or  
b) Repeatedly press Bb on the remote control and then  
press T to change the input; or  
c) Repeatedly press + on the remote control or TV  
control panel to change the input.  
The current signal source displays in the top right corner  
of the Input Selection screen.  
Laser Disk  
Satellite/DSS  
VCR  
Input Selection  
ANT  
0
1
2
3
4
5
6
7
8
9
ANT  
Video Recorder  
Built-In DVD  
Video 1  
Hide (to hide an unused input in the Input Selection screen)  
Video 2  
ColorStream HD1  
ColorStream HD2  
HDMI 1  
Note: If you select Built-In DVD or PC in the Input Selection  
screen, you can choose only “– –” or “Hide” as the label.  
HDMI 2  
HDMI 3  
To label the video input sources:  
PC  
0
9
INPUT  
to Select  
Navigate  
-
/
1
2
3
Press Y and open the Preferences menu.  
Note:  
Highlight Input Labeling and press T.  
You can label the video input sources according to the  
specific devices you have connected to the TV  
(- “Labeling the video input sources” at right).  
Press B or b to highlight the video source you want to  
label.  
Sources can also be “hidden” (- “Labeling the video input  
sources” at right).  
Preferences  
CC Selector  
“No Video Signal” will appear randomly on the screen if no  
signal is received in video input mode.  
Base CC Mode  
Off  
Digital CC Settings  
Input Labeling  
Channel Labeling  
Menu Language  
Channel Browser Setup  
English  
Input Labeling  
Built-In DVD  
Video 1  
--  
VCR  
Video 2  
Cable  
ColorStream HD 1  
ColorStream HD 2  
HDMI 1  
Video Recorder  
Hide  
DTV  
HDMI 2  
Satellite/DSS  
HDMI 3  
DVD  
PC  
--  
Reset  
Done  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
4
5
Press C or c to select the desired label for that input  
Tuning channels  
source. If a particular input is not used, you can select  
Hide as the label, which will cause that input to be  
“grayed out” in the Input Selection screen and skipped  
over when you press + on the remote control.  
Tuning channels using the  
Channel Browser™  
To save the new input labels, highlight Done and press  
T.  
To revert to the factory default labels, highlight Reset  
and press T.  
The Channel Browserprovides an easy navigation interface  
for all your channels and inputs. This feature allows you to:  
Navigate the contents of all of your inputs.  
Input labeling example:  
Keep a list of your favorite channels (see “Favorites  
Browser,” below).  
Keep a history of the last 32 channels or inputs viewed.  
Quickly surf and tune your recently viewed channels/inputs  
from the Channel BrowserHistory List (illustrated on the  
next page).  
Surf via Browse mode (to immediately tune channels as you  
highlight them in the Channel Browser) or Select mode (to  
surf over channels in the Channel Browserbefore you  
select one to tune).  
The screen below left shows the default Input Selection  
screen (with none of the inputs labeled as a specific device).  
The screen below right is an example of how you could label  
the inputs if you connected a VCR to VIDEO 1, Cable TV to  
VIDEO 2, a video recorder to ColorStream HD1, a DTV set-  
top box to HDMI 1, a satellite/DSS set-top box to HDMI 2, and  
a DVD player to HDMI 3. Also note that the ColorStream HD2  
input is labeled “Hidden,” which means that input will be  
skipped over when + is pressed.  
Input Selection  
ANT  
Input Selection  
ANT  
Quickly change inputs from the Inputs List.  
0
1
2
3
4
5
6
7
8
9
ANT  
0
1
2
3
4
5
6
7
8
9
ANT  
Built-In DVD  
Video 1  
Built-In DVD  
VCR  
Favorites Browser  
Video 2  
Cable  
ColorStream HD1  
ColorStream HD2  
HDMI 1  
Video Recorder  
The Favorites Browser allows you to quickly set up a favorite  
ColorStream HD2 (Hidden)  
channels/inputs list that is integrated into the Channel Browser.  
DTV  
HDMI 2  
Satellite/DSS  
DVD  
HDMI 3  
To add a favorite channel/input:  
PC  
PC  
0
9
INPUT to Select  
Navigate  
0
9
INPUT  
to Select  
Navigate  
-
/
-
/
1
2
Tune to the channel or input.  
Input Selection screen with  
no inputs labeled.  
Input Selection screen with  
all inputs labeled except input 5,  
which has been hidden.  
Press and hold n for 3 seconds.  
Note: Additions are added to the beginning of the Favorites list  
on the left side of the Channel Browser.  
To clear the input labels:  
To delete a favorite channel/input:  
1
2
3
Press Y and open the Preferences menu.  
Highlight Input Labeling and press T.  
1
2
Press n to open the Favorites browser list.  
Highlight Reset and press T.  
Highlight the channel or input to delete by pressing  
3 C or # c.  
3
Press and hold = for 3 seconds. The channel/input will  
be removed from the Favorites list.  
To set up the Channel Browser:  
1
2
3
Press Y and open the Preferences menu.  
Highlight Channel Browser Setup and press T.  
Press B to highlight Navigation, and then press C or c  
to select either Browse Mode or Select Mode.  
Channel Browser Setup  
Navigation  
History List  
ANT List  
Select Mode  
Power Off Clear (On)  
On  
On  
On  
Inputs List  
Favorites List  
Reset  
Done  
(continued)  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Note:  
4
Press b to highlight History List, and then press C or c  
The Channel Browseropens in History List by default.  
Once another list has been selected, the Channel Browser™  
will open in the last selected list.  
to select the setting you prefer: either Power Off Clear  
(On), On, or Off.  
Note: When History List is set to On, the channels and  
inputs stored in the list will be saved every power on/off  
cycle. When History List is set to Power Off Clear (On),  
the channels and inputs stored in the list will be cleared  
with every power on/off cycle of the TV.  
If all lists are turned off, pressing 3 C, # c, or n will  
not display the Channel Browser. If Favorites List is  
turned off, n will have no effect.  
Pressing n will bring up the Channel Browser™  
Favorites list regardless of the last selected list in the  
Channel Browser.  
5
6
7
8
Press b to highlight ANT List, and then press C or c to  
select On or Off.  
To tune to a channel or input in Browse mode:  
Press b to highlight Inputs List, and then press C or c  
to select On or Off.  
1
While watching TV, press 3 C or # c to open the  
Channel Browserand surf back to a previous item or  
surf forward to the next item in the list.  
Press bto highlight Favorites List, then press C or cto  
select On or Off.  
To save your entries, highlight Done and press T.  
To return to factory defaults, highlight Reset and  
press T.  
In Browse mode, when you stop on an item in the  
Channel Browser, it will be highlighted and the TV will  
automatically tune to the channel or input.  
2
Press O to close the Channel Browser.  
To open the Channel Browser:  
To tune to a channel or input in Select mode:  
Press 3 C or # c on the remote control.  
Press 3 C to surf backward through the previously tuned 32  
channels in the History list, the channels in the ANT channel  
list, the inputs in the Inputs list, or the favorite channels/  
inputs in Favorites list.  
Press # c to surf forward through the channel History, the  
ANT channel list, the Inputs list, or the favorite channels/  
inputs in Favorites list.  
1
While watching TV, press 3 C or # c to open the  
Channel Browserand surf back to a previous item or  
forward to the next item in the list.  
In Select mode, when you stop on an item in the Channel  
Browser, it will be highlighted but you must press T to  
tune the TV to the highlighted item.  
2
3
Press T to tune the TV to the highlighted item.  
Press O to close the Channel Browser.  
Note: To access the Channel Browser™ while on the Built-In  
DVD input, first press E then press 3 C, # c or n.  
Elements of the Channel Browser™  
Adding and clearing channels and inputs in the  
History List  
1
2
3
4
History  
Adding channels and inputs to the History List:  
88  
10  
2
11  
3
8
As a channel or input is tuned, the Channel Browseradds it  
to the History List and displays it on the “right side” of the  
Channel Browser. Previously tuned channels/inputs are  
“shifted” to the left, eventually moving off the left side. Press  
3 C to surf backward through the previously tuned channels/  
inputs. Any channel or input that is tuned repeatedly will not  
be repeated in the History List, but instead is moved to the end  
of the list on the right side of the Channel Browser.  
The Channel Browserwill store the following channels:  
All channels that are tuned using the numeric buttons on the  
remote control.  
TVLAND  
ABCHD  
WEATHER  
5
6
1
2
3
4
Current list (History, ANT, Inputs, or Favorites)  
Input type  
Channel or input currently being viewed  
Channel or input that is currently highlighted in the  
browser  
All channels that are tuned using < or , on the remote  
5
6
Channels stored in the History List  
Channel labels  
control.  
Note: Whenever an item is selected that cannot be tuned (for  
various reasons), the TV will automatically tune to the  
previously viewed channel or input.  
To toggle among the available lists:  
After opening the Channel Browser, press B or b to toggle  
among History, ANT, Inputs, and Favorites.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Clearing channels from the History List:  
Reconfiguring the ANT input will clear the History List.  
Switching between two channels using  
SurfLock™  
Note: See page 32 for details on configuring the antenna  
input.  
The SurfLockfeature temporarily “memorizes” one channel  
to the R button, so you can return to that channel quickly  
from any other channel by pressing R. To memorize a  
channel to the R button:  
Once 32 channels or inputs are stored in the History List, the  
oldest item will be removed from the list when a new  
channel or input is tuned.  
1
2
Tune the TV to the channel you want to program into the  
R button.  
If History List in the Channel Browser Setup is set to  
Power Off Clear (On),” turning off the TV will clear the  
History List.  
Press and hold R for about 2 seconds until the message  
“Channel Memorized” appears on-screen. The channel  
has been programmed to the R button.  
Tuning to the next programmed channel  
3
You can then change channels repeatedly, and when you  
press R, the memorized channel will be tuned.  
To tune to the next programmed channel:  
Press < or , on the remote control or TV control panel.  
The TV will return to the memorized channel one time only.  
Once you press R and then change channels again, the CH  
RTN memory will be cleared and the button will function as  
Channel Return, by switching back and forth between the last  
two channels that are tuned. This feature also works for  
external inputs.  
Note:This feature will not work unless you program channels  
into the TV’s channel memory (- page 33).  
Tuning to a specific channel (programmed  
or unprogrammed)  
Tuning analog channels:  
Press the Channel Number (0–9) on the remote control. For  
example, to select channel 125, press 1, 2, 5.  
Tuning digital channels:  
Press the Channel Number (0–9) on the remote control,  
followed by the dash (=) button and then the sub-channel  
number. For example, to select digital channel 125-1, press 1,  
2, 5, –, 1.  
Note: If a digital channel is not programmed—either through  
the automatic channel scan (- page 33) or the channel add/  
delete function (- page 33)—you will have to tune the RF  
channel using the Channel Number and dash (=) on the  
remote control.  
Switching between two channels using  
Channel Return  
The Channel Return feature allows you to switch between two  
channels without entering an actual channel number each time.  
1
2
Select the first channel you want to view.  
Select a second channel using the Channel Number  
buttons (and the dash (=) button if selecting a digital  
channel).  
3
Press R on the remote control. The previous channel  
will display. Each time you press R, the TV will switch  
back and forth between the last two channels that were  
tuned.  
Note: If you press R from a non-antenna input, the TV  
will return to the last-viewed input.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Note: If you select one of the TheaterWide® picture sizes, the  
top and bottom edges of the picture (including subtitles or  
captions) may be hidden. To view the hidden edges, either  
scroll the picture (TheaterWide 2 and 3 only) or try viewing the  
program in Full or Natural picture size.  
Selecting the picture size  
You can view many program formats in a variety of picture  
sizes—Natural, TheaterWide 1, TheaterWide 2,  
TheaterWide 3, Full, 4:3 HD and Native.  
Natural picture size  
The image is displayed close to its originally formatted  
proportion. Some program formats will display with  
sidebars and/or bars at the top and bottom.  
Note: The “picture size” illustrations are examples only. The  
format of the image (in any of the picture sizes) will vary  
depending on the format of the signal you are currently  
watching. Select the picture size that displays the current  
program the way that looks best to you.  
You can save separate picture size preferences for each input  
on your TV.  
To select the picture size using the remote control:  
1
2
Press I on the remote control.  
Natural picture size example  
While the Picture Size screen is open, you can do one of  
the following to select the desired picture size:  
TheaterWide 1 picture size (for 4:3 format programs)  
Repeatedly press I.  
Press the corresponding Number button (0–6) while the  
Picture Size screen is open.  
The center of the picture remains close to its original  
proportion, but the left and right edges are stretched wider to  
fill the screen.  
Press B or b while the Picture Size screen is open.  
Picture Size  
0
1
2
3
4
5
6
Natural  
TheaterWide 1  
TheaterWide 2  
TheaterWide 3  
Full  
TheaterWide 1 picture size example  
4:3 HD  
Native  
TheaterWide 2 picture size (for letter box programs)  
0
6
PIC SIZE  
to Select  
-
/
The picture is stretched wider to fill the width of the screen,  
but only slightly stretched taller.  
The top and bottom edges of the picture may be hidden. To  
view the hidden areas, see “Scrolling the TheaterWide®  
picture” (- page 43).  
To select the picture size using the menus:  
1
2
3
Select Picture Size in the Theater Settings menu.  
Press C or c to select the desired picture size setting.  
Highlight Done and press T.  
Theater Settings  
Mode: Sports  
Picture Size  
Full  
Picture Scroll  
--  
A B C D E F G - - - - - - - - - - - - - - - -  
Cinema Mode  
Auto Aspect Ratio  
DVD Aspect Ratio  
Film  
On  
TheaterWide 2 picture size example  
16:9 Wide  
Reset  
Done  
Note: Some of the picture sizes may not be available  
depending on the receiving signal format (those will be  
“grayed out” in the Picture Size screen).  
Using these functions to change the picture size (i.e.,  
changing the height/ width ratio) for any purpose other than  
your private viewing may be prohibited under the Copyright  
Laws of the United States and other countries, and may  
subject you to civil and criminal liability.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Note:  
TheaterWide 3 picture size (for letter box programs  
Native picture size is available for 720p, 1080i, and 1080p  
signals only. If the signal being received is other than 1080i,  
1080p, or 720p, “Native” will be grayed out in the Picture  
Size screen.  
with subtitles)  
The picture is stretched wider to fill the width of the screen,  
but only slightly stretched taller.  
The top and bottom edges are hidden. To view the hidden  
areas (such as subtitles or captions), see “Scrolling the  
TheaterWide® picture.”  
This mode is supported only for HDMI and ColorStream  
inputs.  
Depending on the input signals, the border of the picture  
may be hidden, displayed in black, or noisy.  
A B C D E F G - - - - - - - - - - - - - - - -  
A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -  
TheaterWide 3 picture size example  
Native picture size example  
Full picture size (for 16:9 [480i, 480p] source  
programs only)  
Scrolling the TheaterWide® picture  
(TheaterWide 2 and 3 only)  
If receiving a squeezed 4:3 format program, the picture is  
stretched wider to fill the width of the screen, but not  
stretched taller.  
None of the picture is hidden.  
You can set separate scroll settings for the TheaterWide 2 and  
TheaterWide 3 modes for each input.  
To set the scroll settings:  
1
2
Press Y and open the Video menu.  
Highlight Theater Settings and press T.  
Full picture size example  
4:3 HD picture size (for 720p, 1080i, and 1080p  
program sources only)  
Sidebars fill the empty vertical spaces.  
Picture is not distorted from original size.  
Video  
Mode  
Sports  
Off  
Picture Settings  
Noise Reduction  
Game Mode  
Theater Settings  
3
In the Picture Size field, select either TheaterWide 2  
or TheaterWide 3 (you cannot scroll in any other mode).  
4
5
Press b to highlight the Picture Scroll field.  
Press C or c to scroll the picture up and down as needed,  
from –10 to +20.  
4:3 HD picture size example  
Native picture size (for 720p, 1080i, and 1080p signal  
programs)  
If receiving a 720p, 1080i, or 1080p signal program, Native  
mode scales the video to display the entire picture within the  
borders of the screen (i.e. no overscanning).  
Mode: Sports  
TheaterWide 2  
Theater Settings  
Picture Size  
Picture Scroll  
Cinema Mode  
-5  
Film  
On  
Auto Aspect Ratio  
DVD Aspect Ratio  
16:9 Wide  
This is especially useful for external HD sources such as  
HD-DVD, DVHS movies, or PC graphics.  
Reset  
Done  
6
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Using the auto aspect ratio feature Selecting the cinema mode  
(480i and 1080i signals)  
When the auto aspect ratio feature is set to On, the TV will  
automatically select the picture size when one of the following  
When you view a DVD (3:2 pulldown processed) from a DVD  
input sources is received:  
player connected to the VIDEO 1, VIDEO 2, ColorStream  
A 480i signal from the VIDEO 1, VIDEO 2, ColorStream  
HD-1, or ColorStream HD-2 input.  
A 480i, 480p, 720p, 1080i, 1080p, or VGA signal from the  
HDMI input.  
HD-1, ColorStream HD-2 (component video), or HDMI  
inputs on the TV, smoother motion can be obtained by setting  
the Cinema Mode to Film.  
To set the Cinema Mode to Film:  
Aspect ratio of Automatic aspect size (automatically  
signal source selected when Auto Aspect is On)  
1
2
3
Press Y and open the Video menu.  
Highlight Theater Settings and press T.  
In the Cinema Mode field, select Film.  
4:3 normal  
Natural (with sidebars)  
4:3 letter box TheaterWide 2  
16:9 full  
Full  
Mode: Sports  
Theater Settings  
Not defined  
Picture Size  
Natural  
(no ID-1 data The current picture size you set under  
Picture Scroll  
--  
or HDMI  
aspect data)  
“Selecting the picture size” on page 42.  
Cinema Mode  
Auto Aspect Ratio  
DVD Aspect Ratio  
Film  
On  
16:9 Wide  
Note: The auto aspect ratio feature is not applicable to  
antenna or cable input sources.  
Reset  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
To turn on the auto aspect ratio feature:  
1
2
3
Press Y and open the Video menu.  
To set the Cinema Mode to Video:  
Select Video in step 3 above.  
Highlight Theater Settings and press T.  
In the Auto Aspect Ratio field, select On.  
Mode: Sports  
Theater Settings  
Picture Size  
Natural  
Picture Scroll  
--  
Cinema Mode  
Film  
Auto Aspect Ratio  
DVD Aspect Ratio  
On  
16:9 Wide  
Reset  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
To turn off the auto aspect ratio feature:  
Select Off in step 3 above.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Adjusting the picture quality  
You can adjust the picture quality (Contrast, Back Light,  
DynaLight™, Brightness, Color, Tint, and Sharpness) to your  
personal preferences.  
Adjusting the picture  
Selecting the picture mode  
You can select your desired picture settings from four different  
modes, as described below.  
Selection  
Contrast  
Back Light*  
DynaLight**  
Brightness  
Color  
Pressing C  
lower  
Pressing c  
higher  
darker  
On/Off  
darker  
paler  
lighter  
Mode  
Picture Quality  
On/Off  
lighter  
Sports  
Standard  
Bright and dynamic picture (factory setting)  
Standard picture settings (factory setting)  
deeper  
Lower contrast for darkened room (factory  
setting)  
Movie  
Tint  
reddish  
softer  
greenish  
sharper  
Preference  
Your personal preferences  
Sharpness  
To select the picture mode:  
Press u on the remote control.  
The following popup menu appears on-screen.  
* Back Light  
This feature adjusts the brightness of the entire screen. When in  
video mode and no signal is input, this will automatically be set to 0.  
(Settings are stored in memory.)  
**DynaLight  
This function automatically strengthens the black coloring of dark  
areas in the video according to the level of darkness.  
Sports  
Standard  
Movie  
To adjust the picture quality:  
Preference  
1
2
3
Press Y and open the Video menu.  
Press B or b to select the picture mode you prefer and  
press T.  
Highlight Picture Settings and press T.  
Press B or b to select the picture quality you want to  
adjust (Contrast, Back Light, DynaLight,  
Brightness, Color, Tint, or Sharpness), and then  
press C or c to adjust the setting, as described in the table  
above.  
To select the picture mode using the menu system:  
1
2
Press Y and open the Video menu.  
Highlight Mode and press T.  
Picture Settings  
Mode: Sports  
Contrast  
100  
Back Light  
DynaLight  
Brightness  
Color  
100  
Video  
Mode  
On  
Sports  
50  
50  
0
Picture Settings  
Noise Reduction  
Tint  
Off  
Game Mode  
Sharpness  
Advanced Picture Settings  
50  
Theater Settings  
Reset  
Done  
3
Press B or b to select the picture mode you prefer and  
press T.  
Picture Settings  
Mode: Preference  
Contrast  
70  
Sports  
4
To save the new settings, highlight Done and press T.  
Standard  
Movie  
You can use any of the picture modes (- “Selecting the  
picture mode,” above left) as a starting point for adjusting  
the picture settings.  
Preference  
Note: The picture mode you select affects the current  
input only. You can select a different picture mode for  
each input.  
To revert back to the base mode that you began adjusting  
the picture settings from, highlight Reset and press T.  
The picture qualities you adjusted are automatically saved in  
the Preference mode (- “Selecting the picture mode,”  
above left) until Reset is selected.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Note: A closed caption signal may not display in the following  
situations:  
When a videotape has been dubbed  
When the signal reception is weak  
When the signal reception is non-standard  
Using the closed caption mode  
Base closed captions  
The closed caption mode has two options:  
Captions—An on-screen display of the dialogue, narration,  
and sound effects of TV programs and videos that are closed  
captioned (usually marked “CC” in program guides).  
Text—An on-screen display of information not related to  
the current program, such as weather or stock data (when  
provided by individual stations).  
Digital CC Settings  
You can customize the closed caption display characteristics  
by changing the background color, opacity, text size, type,  
edge, and color.  
Note:  
This feature is available for digital channels only.  
You cannot set the Caption Text and Background as the  
same color.  
To view captions or text:  
1
2
3
Press Y and open the Preferences menu.  
To customize the closed captions:  
Highlight Base CC Mode and press c.  
1
2
3
Press Y and open the Preferences menu.  
Press Bor bto select the desired closed caption mode and  
press T.  
Highlight Digital CC Settings and press T.  
Press B or b to highlight the characteristic you want to  
change, and then press C or c to select the format for that  
characteristic (see table below).  
Preferences  
CC Selector  
Off  
CC1  
CC2  
CC3  
CC4  
T1  
Base CC Mode  
Off  
Digital CC Settings  
Digital CC Settings  
Input Labeling  
Caption Size  
Auto  
Auto  
Channel Labeling  
Menu Language  
Caption Text Type  
Caption Text Edge  
Caption Text Color  
Text Foreground Opacity  
Background Color  
English  
Auto  
Channel Browser Setup  
Auto  
T2  
Auto  
T3  
Auto  
T4  
Text Background Opacity  
Caption Text Edge Color  
Auto  
To view captions:  
Highlight CC1, CC2, CC3, or CC4. (CC1 displays  
translation of the primary language in your area.)  
Auto  
ABC123  
Preview  
window  
Reset  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Caption Size  
Auto, Small, Standard, Large  
Giant pandas eat leaves.  
Auto, Default, Mono w. Serif, Prop. w.  
Serif, Mono w/o Serif, Prop. w/o Serif,  
Casual, Cursive, Small Capitals  
Note: If the program or video you selected is not closed  
captioned, no captions will display on-screen.  
Caption Text  
Type  
To view text:  
Highlight T1, T2, T3, or T4.  
Caption Text  
Edge  
Auto, None, Raised, Depressed, Uniform,  
Left Drop Shadow, Right Drop shadow  
Caption Text  
Color  
Auto, Black, White, Red, Green, Blue,  
Yellow, Magenta, Cyan  
WORLD WEATHER  
Temps  
Current  
Weather  
Clear  
F
C
LONDON  
MOSCOW  
PARIS  
51  
57  
53  
66  
65  
11  
14  
12  
19  
18  
Text Foreground Auto, Transparent, Translucent  
Opacity  
Cloudy  
Clear  
Cloudy  
Rain  
ROME  
Flashing, Solid  
TOKYO  
Background  
Color  
Auto, Black, White, Red, Green, Blue,  
Yellow, Magenta, Cyan  
Note: If text is not available in your area, a black rectangle  
may appear on screen. If this happens, set the Base CC  
Mode to Off.  
Text Background Auto, Transparent, Translucent  
Opacity  
To turn off the closed caption mode:  
Select Off in step 3 above.  
Flashing, Solid  
Caption Text  
Edge Color  
Auto, Black, White, Red, Green, Blue,  
Yellow, Magenta, Cyan  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
CC Selector  
Adjusting the audio  
You can use the CC Selector to temporarily override the  
default analog caption mode (set in Base CC Mode) for a  
particular channel. However, once you change to another  
analog channel, the closed caption setting will automatically  
change back to the current Base CC Mode setting.  
Muting the sound  
Press W to partially reduce (1/2 MUTE) or turn off (MUTE)  
the sound. Each time you press W, the mute mode will change  
in the following order:  
You can also use the CC Selector to select digital closed  
caption services (if available). When such services are not  
available, the CC Selector presents a default list of services.  
If the selected service is not available, the next best service will  
be used instead.  
1/2 Mute  
Mute  
Volume  
If the closed caption mode is set to Off when you select  
“MUTE” mode, the closed caption feature is automatically  
activated. To mute the audio without automatically activating  
the closed caption feature, use Z to set the volume to 0. See  
“Using the closed caption mode” (- page 46) for more  
information on closed caption modes.  
To select closed captions:  
1
2
Press Y and open the Preferences menu.  
Highlight CC Selector and press T.  
Using the digital audio selector  
Preferences  
CC Selector  
You can use the Digital Audio Selector to conveniently  
switch between audio tracks on a digital channel (for those  
channels that have multiple audio tracks). This temporarily  
overrides the audio track chosen by the language option under  
Audio Setup (- “Selecting stereo/SAP broadcasts” on  
page 48).  
Base CC Mode  
Off  
Digital CC Settings  
Input Labeling  
Channel Labeling  
Menu Language  
English  
Channel Browser Setup  
3
4
Press B or b to select Closed Caption, and then press  
To use the digital audio selector:  
C or c to select the desired service.  
1
2
Press Y and open the Audio menu.  
Closed Caption  
CC 1  
None  
Audio  
Highlight Digital Audio Selector and press T.  
Press O.  
Audio  
Digital Audio Selector  
Audio Settings  
Advanced Audio Settings  
Audio Setup  
3
4
Press B or b to select Audio, and then press C or c to  
select the desired service.  
Closed Caption  
CC 1  
None  
Audio  
Press O.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
To listen to a second audio program on an analog  
station (if available):  
Select SAP in step 3 above.  
Selecting stereo/SAP broadcasts  
The multi-channel TV sound (MTS) feature allows you to  
output high-fidelity stereo sound. MTS also can transmit a  
second audio program (SAP) containing a second language,  
music, or other audio information (when provided by  
individual stations).  
Note:  
A second audio program (SAP) can be heard only on those  
TV stations that offer it. For example, a station might  
broadcast another language as a second audio program. If  
you have SAP on, you will see the current program on the  
screen but hear the other language instead of the program’s  
normal audio.  
When the TV receives a stereo or SAP broadcast, the word  
“STEREO” or “SAP” appears on-screen when E is pressed.  
The MTS feature is not available when the TV is in VIDEO  
mode.  
If you have SAP on and the station you are watching is not  
broadcasting a second audio program, the station’s normal  
audio will be output. However, occasionally there is no  
sound at all in SAP mode. If this happens, set the MTS  
feature to Stereo mode.  
To listen to stereo sound:  
1
2
Press Y and open the Audio menu.  
Highlight Audio Setup and press T.  
Adjusting the audio quality  
You can adjust the audio quality by adjusting the bass, treble,  
and balance.  
Audio  
Digital Audio Selector  
Audio Settings  
Advanced Audio Settings  
To adjust the audio quality:  
Audio Setup  
1
2
3
Press Y and open the Audio menu.  
3
4
In the MTS field, select Stereo.  
Highlight Audio Settings and press T.  
Audio Setup  
PC Audio  
No  
Auto  
Press b or B to highlight the item you want to adjust  
(Bass, Treble, or Balance).  
HDMI 1 Audio  
MTS  
Stereo  
Audio Settings  
Language  
English  
Bass  
100  
100  
0
Optical Output Format  
Dolby Digital/Surround  
Treble  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
Balance  
StableSound  
DVD Audio  
Reset  
Off  
Done  
Done  
Reset  
4
5
Press C or c to adjust the level.  
To save the new settings, highlight Done and press T.  
To reset the settings to the factory defaults, highlight  
Reset and press T.  
C makes the bass or treble weaker or increases the  
balance in the left channel (depending on the item  
selected).  
c makes the bass or treble stronger or increases the  
balance in the right channel (depending on the item  
selected).  
Note:  
You can typically leave the TV in Stereo mode because  
it will automatically output the type of sound being  
broadcast (stereo or monaural).  
If the stereo sound is noisy, select Mono to reduce the  
noise.  
To save the new settings, highlight Done and press T.  
To reset the settings to the factory defaults, highlight  
Reset and press T.  
To listen to an alternate language on an ATSC digital  
station (if available):  
Highlight the Language field in step 3 above, and then press  
C or c to select the language you prefer.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Using the StableSound® feature  
3
In the Optical Output Format field, select either  
Dolby Digital/Surround or PCM, depending on your  
The StableSound® feature limits the highest volume level to  
prevent extreme changes in volume when the signal source  
changes (for example, to prevent the sudden increase in  
volume that often happens when a TV program switches to a  
commercial).  
device.  
Audio Setup  
PC Audio  
No  
Auto  
HDMI 1 Audio  
MTS  
Stereo  
Language  
English  
®
To turn on the StableSound feature:  
Optical Output Format  
Dolby Digital/Surround  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
1
2
3
Press Y and open the Audio menu.  
Highlight Audio Settings and press T.  
In the StableSound field, select On.  
Audio Settings  
DVD Audio  
Reset  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Bass  
100  
100  
0
Treble  
Balance  
StableSound  
Note: You cannot change the optical audio output format while  
you are viewing a DVD. (You must be in FULL-STOP mode, not  
RESUME-STOP mode.)  
On  
Done  
Reset  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Using the Dolby® Digital Dynamic Range  
Control feature  
This dynamic range control feature causes the ATSC dynamic  
range to be further compressed, allowing you to switch from  
ATSC to analog broadcasts at the same dynamic range.  
Note: The RESET function returns your audio adjustments  
to the following factory settings:  
Bass . . . . . . . . center (50)  
Treble . . . . . . . center (50)  
Balance . . . . . . center (0)  
StableSound . . Off  
To use the Dolby Digital Dynamic Range Control:  
1
2
3
Press Y and open the Audio menu.  
To turn off the StableSound feature:  
Select Off in step 3 above.  
Highlight Audio Setup and press T.  
In the Dolby Digital Dynamic Range Control field,  
select Compressed. When Standard is selected, the  
audio is output with minimal compression.  
Selecting the optical audio output format  
You can use this feature to select the optical audio output  
format when you connect a Dolby Digital decoder or other  
digital audio system to the Optical Audio Out terminal on  
the TV (see “Connecting a digital audio system” on page 21).  
Audio Setup  
PC Audio  
No  
Auto  
HDMI 1 Audio  
MTS  
Stereo  
Language  
English  
To select the optical audio output format:  
Optical Output Format  
Dolby Digital/Surround  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
1
2
Press Y and open the Audio menu.  
DVD Audio  
Reset  
Highlight Audio Setup and press T.  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Note:  
This item will be grayed out for NTSC signals, Video,  
ColorStream, and PC inputs.  
The Dolby Digital Dynamic Range Control will function in  
relation to Optical Output Format (PCM mode).  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
When the correct PIN code is entered, the Locks menu opens.  
Using the Locks menu  
The Locks menu includes the Enable Rating Blocking, Edit  
Rating Limits, Channels Block, Input Lock, Front (control)  
Panel Lock, and New PIN Code features. You can use these  
features after entering the correct PIN code.  
Locks  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
Off  
Off  
Front Panel Lock  
New PIN Code  
Entering the PIN code  
1
Press Y and highlight the Locks menu icon.  
If you cannot remember your PIN code  
While the PIN code entering screen is displayed, press E  
four times within five seconds. The PIN code will be cleared  
and you can enter a new PIN code.  
Locks  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
Off  
Off  
Changing your PIN code  
Front Panel Lock  
New PIN Code  
1
2
3
4
Press Y and highlight the Locks menu icon.  
Press b to display the PIN code entering screen.  
Enter your four-digit PIN code and press T.  
Press b to highlight New PIN Code and press T.  
2
Press b, which displays the PIN code entry screen.  
The Lock System screen (below) appears if a PIN  
code has not been stored. Press the Channel Number  
buttons to enter a new four-digit code, enter the code a  
second time to confirm, and press T.  
Lock System  
Locks  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
Please enter a 4 digit PIN code  
Off  
Off  
Confirm PIN code  
Front Panel Lock  
New PIN Code  
Cancel  
Done  
5
6
Press the Number buttons to enter a new four-digit code.  
Reenter the PIN code to confirm it.  
The Locks/Active screen (below) appears if the PIN  
code is already stored. Use the Number buttons to enter  
your four-digit code and press T.  
Press T. The new PIN code is now active.  
New PIN Code  
Locks  
Active  
Please enter a 4 digit PIN code  
Please enter the 4 digit PIN code  
*
*
*
*
*
*
*
*
Confirm PIN code  
*
*
*
*
Cancel  
Done  
Cancel  
Done  
If the wrong PIN code is entered, the message “Incorrect PIN  
code, please try again!” appears. Highlight Retry and press  
T. Enter the code again and press T.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Blocking TV programs and movies  
by rating (V-Chip)  
Some TV programs and movies include signals that classify  
the content of the program (violence, sex, dialog, language).  
The V-Chip feature in this TV detects the signals and blocks  
the programs according to the ratings you select. (For rating  
descriptions, see the tables on the next page.)  
Downloading an additional rating system  
for blocking TV programs and movies  
In the future, an additional rating system may become  
available for use in selectively blocking programs.  
Note: The currently tuned station must be receiving a digital  
signal before an additional rating system can be downloaded.  
To download the additional rating system  
(if available):  
Note: Rating blocking is a function of the V-Chip feature in this  
TV, which supports the U.S. V-Chip system only.  
To block and unblock TV programs and movies:  
1
2
3
4
5
6
Press Y and highlight the Locks menu icon.  
Press b to display the PIN code entering screen.  
Enter your four-digit PIN code and press T.  
Press b to highlight Enable Rating Blocking.  
Press c and b to select On, and press T.  
1
2
3
4
5
Press Y and highlight the Locks menu icon.  
Press b to display the PIN code entering screen.  
Enter your four-digit PIN code and press T.  
Press b to highlight Enable Rating Blocking.  
Press c and b to select On, and then press T.  
Press b to highlight Edit Rating Limits and press T.  
The Edit Rating Limits screen appears.  
7
Highlight Alt RS and press T. The Edit Alternate  
Ratings screen will appear.  
Locks  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
Off  
Note:  
On  
The Alt RS button will only be available if an additional  
rating system is currently available.  
It may take several minutes for the TV to download the  
Off  
Off  
Front Panel Lock  
New PIN Code  
additional rating system.  
6
7
Press b to highlight Edit Rating Limits and press T.  
The Edit Rating Limits screen (below) appears.  
The information displayed in the Alternate Ratings  
screen will depend on the configuration of the  
additional rating system available at the time of  
download.  
Press BbC c and then press T to select the level of  
blocking you prefer. A box with an “5” is a rating that will  
be blocked. As you highlight a rating, a definition for the  
rating appears at the bottom of the screen.  
8
9
Press B b C c and then press T to select the level of  
blocking you prefer. A box with an “5” is a rating that will  
be blocked.  
8
When done selecting the ratings you want to block,  
highlight Done and press T.  
When you are finished selecting the ratings you want to  
block, highlight Done and press T.  
Edit Rating Limits  
Movies  
G
TV (V-CHIP) FV  
TV-Y  
D
L
S
V
10 In the Edit Rating Limits screen, highlight Done and  
Children  
Youth  
press T.  
TV-Y7  
TV-G  
PG  
PG-13  
R
Note:  
TV-PG  
TV-14  
TV-MA  
NC-17  
X
Alt RS  
Cancel  
Done  
The additional rating system can only be downloaded one  
time. You will not be able to download any updates to the  
rating system should such updates become available.  
"None" Rated  
The additional rating system is not designed, transmitted, or  
controlled by the TV or Toshiba, nor is the availability of an  
additional rating system determined or controlled by  
Toshiba. Similarly, the rating of programs in an additional  
rating system is not determined, transmitted, or controlled  
by the TV or Toshiba.  
The additional rating system is an evolving technology;  
therefore, availability, content, and format may vary.  
(continued)  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Blocking channels  
With the Channels Block feature, you can block specific  
channels. You will not be able to tune blocked channels unless  
you unlock them.  
Independent rating system for broadcasters  
Ratings  
Description and Content themes  
Mature Audience Only (This program is specifically  
designed to be viewed by adults and therefore may  
be unsuitable for children under 17.)  
L) Crude or indecent language S) Explicit sexual  
activity V) Graphic violence  
TV-MA  
To block channels:  
Parents Strongly Cautioned (This program contains  
some material that many parents would find  
unsuitable for children under 14 years of age.)  
D) Intensely suggestive dialog L) Strong, coarse  
language S) Intense sexual situations V) Intense  
violence  
1
2
3
Press Y and highlight the Locks menu icon.  
Press b to display the PIN code entering screen.  
TV-14  
Enter your four-digit PIN code and press T  
(- page 50).  
4
Press b to highlight Channels Block and then press T.  
Parental Guidance Suggested (This program  
contains material parents may find unsuitable for  
younger children.)  
D) Some suggestive dialog L) Infrequent coarse  
language S) Some sexual situations V) Moderate  
violence  
A list of the channels available for that input will be  
displayed along with the call letters for each channel, if  
available.  
TV-PG  
TV-G  
General Audience (Most parents would find this  
program suitable for all ages.)  
Locks  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
Directed to Older Children (This program is designed  
for children age 7 and above. Note: Programs in  
which fantasy violence may be more intense or more  
combative than other programs in this category are  
designated TV-Y7FV.)  
TV-Y7,  
TV-Y7FV  
Off  
Off  
Front Panel Lock  
New PIN Code  
All Children (This program is designed to be  
appropriate for all children.)  
TV-Y  
5
Press Bb to highlight the channel you want to block and  
press T, which puts an “5” in the box next to that  
channel.  
Independent rating system for movies  
Ratings  
X
NC-17  
Description and Content themes  
X-rated (For adults only)  
Channels Block  
1
2
3
4
5
6
Not intended for anyone 17 and under  
Restricted (Under 17 requires accompanying parent  
or adult)  
R
Parents Strongly Cautioned (Some material may be  
inappropriate for children under 13)  
7
Allow All  
PG-13  
8
9
Block All  
Cancel  
Done  
Parental Guidance Suggested (Some material may  
not be suitable for children)  
10  
PG  
G
General Audience (Appropriate for all ages)  
6
7
Repeat step 5 for other channels you want to block.  
Highlight Done and press T.  
Note:  
If you place an “5” in the box next to “ ‘None’ Rated,”  
programs rated “None” will be blocked; however, programs  
that do not provide any rating information will not be  
blocked.  
To display the rating of the program you are watching, press  
E on the remote control. If it is rated “None,” the word  
NONE” appears in the RECALL screen (as shown below  
right). If rating information is not provided, no rating will  
appear in the RECALL screen.  
To unblock individual channels:  
In step 5 above, press Bb to highlight the channel you want to  
unblock, press T to remove the “5” from the box, highlight  
Done and press T.  
TV - PG  
L
V
NONE  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
To block all channels at once:  
Highlight Block All in step 5 on previous page and then  
highlight Done and press T.  
Using the input lock feature  
You can use the Input Lock feature to lock the video inputs  
(Built-In DVD, VIDEO 1, VIDEO 2, ColorStream HD-1,  
ColorStream HD-2, HDMI 1, HDMI 2, HDMI 3 and PC)  
and channels 3 and 4. You will not be able to view the input  
sources or channels until you unlock the inputs.  
To unblock all locked channels at once:  
Highlight Allow All in step 5 on previous page and then  
highlight Done and press T.  
To lock/unlock the video inputs:  
Channels Block  
1
2
3
4
5
6
1
2
3
4
5
Press Y and highlight the Locks menu icon.  
Press b to display the PIN code entering screen.  
Enter your four-digit PIN code and press T.  
Press b to highlight Input Lock and press c.  
7
8
Allow All  
Block All  
Cancel  
Done  
9
Press B or b to select the level of video input locking you  
prefer, as described below.  
10  
Video: Locks Built-In DVD, VIDEO 1, VIDEO 2,  
ColorStream HD1/HD2, HDMI 1, HDMI 2, HDMI 3, and  
PC.  
Video+: Locks Built-In DVD, VIDEO 1, VIDEO 2,  
ColorStream HD1/HD2, HDMI 1, HDMI 2, HDMI 3, PC  
and channels 3 and 4.  
Unlocking programs temporarily  
If you try to tune the TV to a program that exceeds the rating  
limits you set, the TV will enter program lock mode and the  
following message will appear on-screen:  
Select Video+ if you play video tapes via an ANT  
input.  
This program exceeds the rating limit you set.  
Push 'mute' to enter PIN.  
You can either temporarily unlock the program or select an  
unlocked program to watch.  
Locks  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
To temporarily unlock the program:  
Off  
Off  
1
2
Press W.  
Front Panel Lock  
New PIN Code  
Video  
Video +  
Off  
Enter your four-digit PIN code and press T. If the correct  
code is entered, the program lock mode is released and the  
normal picture appears. All locking is disabled until the  
TV is turned off, and will be enabled when the TV is  
turned on again.  
Off: Unlocks all video inputs and channels 3 and 4.  
6
Press T.  
Locks  
Active  
Enter PIN code to temporarily unblock.  
*
*
*
*
Cancel  
Done  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Using the control panel lock feature  
Using the PC settings feature  
You can lock the control panel to prevent your settings from  
being changed accidentally (by children, for example). When  
the control panel lock is On, none of the controls on the TV  
control panel will operate except POWER.  
You can view an image from a PC on the TV screen.  
When a PC is connected to the TV's PC IN terminal, you can  
use the PC Settings feature to make adjustments to the image.  
If the edges of the picture are cut off, readjust the Horizontal  
Position and Vertical Position. If the picture is affected by  
interference, readjust the Clock Phase and Sampling  
Clock.  
To lock the control panel:  
1
2
3
4
5
Press Y and highlight the Locks menu icon.  
Press b to display the PIN code entering screen.  
Enter your four-digit PIN code and press T.  
Press b to highlight Front Panel Lock.  
To adjust the PC settings:  
1
Repeatedly press + to select PC input mode  
(- “Selecting the video input source to view” page 38).  
Press c and C or c to highlight On and press T. When  
the control panel is locked and any button on the control  
panel (except POWER) is pressed, the message “Not  
Available” appears.  
2
3
Press Y and open the Setup menu.  
Highlight PC Settings and press T.  
Locks  
Setup  
Enable Rating Blocking  
Edit Rating Limits  
Channels Block  
Input Lock  
Off  
Installation  
Sleep Timer  
PC Settings  
Off  
Front Panel Lock  
New PIN Code  
Off  
Off  
Note: If a PC is not connected or there is no pc input  
On  
signal, this feature will be grayed out in the Setup menu.  
4
5
Press B or b to highlight the item you want to adjust.  
Press C or c to make the appropriate adjustments.  
PC Settings  
To unlock the control panel:  
Highlight Off in step 5 above, or press and hold the  
VOLUME – button on the TV control panel for about 10  
seconds until the volume icon appears.  
Horizontal Position  
Vertical Position  
Clock Phase  
0
0
0
0
Sampling Clock  
Reset  
Done  
Note: The screen is disrupted momentarily when  
adjusting the PC settings. This is not a sign of malfunction.  
Horizontal Position:  
Moves the picture left/right.  
The adjustment range is within 10 from center.*  
Vertical Position:  
Moves the picture up/down.  
The adjustment range is within 10 from center.*  
Clock Phase:  
Helps to reduce noise and sharpen the picture.  
The adjustment range is within 4 from center.*  
Sampling Clock:  
Helps to reduce noise and minimize periodic vertical stripes  
on the screen.  
The adjustment range is within 5 from center.*  
* The default settings may vary depending on the input signal format.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Setting the PC Audio  
Setting the sleep timer  
This function allows you to output the sound from your PC (if  
connected) or mute the sound from your PC and output the  
sound from your HDMI (DVI) connection. (- page 20)  
You can set the sleep timer to turn off the TV after a set length  
of time (maximum of 180 minutes).  
To set the sleep timer using the remote control:  
To set the PC Audio:  
Press [ on the remote control to set the length of time until  
the TV turns off. Repeatedly press [ to increase the time in  
10-minute increments, or press B or b to increase or decrease  
the time in 10-minute increments, to a maximum of 180  
minutes.  
1
2
3
Press Y and open the Audio menu.  
Highlight Audio Setup and press T.  
Press B or b to select PC Audio and then press C or c  
to select No or Yes.  
To set the sleep timer using the on-screen menus:  
Yes: Outputs the sound from your PC.  
No: Mutes the sound from your PC, and outputs the  
sound from the HDMI-1 connection.  
1
2
Press Y and open the Setup menu.  
Highlight Sleep Timer and press T.  
Audio Setup  
PC Audio  
No  
Auto  
HDMI 1 Audio  
MTS  
Setup  
Stereo  
Installation  
Sleep Timer  
PC Settings  
Language  
English  
Optical Output Format  
Dolby Digital/Surround  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
3
Press the Number buttons to enter the length of time in  
10-minute increments.  
DVD Audio  
Reset  
Done  
Sleep Timer  
Note: Because the PC and HDMI-1 inputs share the same  
set of analog audio inputs, the PC Audio menu setting  
influences the HDMI 1 Audio menu setting. If PC Audio is  
set to “No,” the HDMI 1 Audio setting changes to “Auto.”  
If PC Audio is set to “Yes,” the HDMI 1 Audio setting is  
set to “Digital” and is grayed out in the menu. (Also see  
item 4 on page 14 and “Setting the HDMIAudio mode”  
on page 35.)  
Enter total minutes until the TV  
turns off automatically (Maximum  
180 minutes)  
1 2 0  
Cancel  
Done  
4
Highlight Done and press T.  
Note: When a power failure occurs, the sleep timer setting  
may be cleared.  
To display the remaining sleep time:  
Press [.  
Sleep Timer  
120 minutes  
Note: A message will display on-screen when there is one  
minute remaining on the sleep timer.  
To cancel the sleep timer:  
Repeatedly press [ until it is set to 0 minute.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 6: Using the TV’s features  
Displaying TV status information  
Understanding the auto power off  
feature  
To display TV status information using RECALL:  
Press E on the remote control.  
The following information will display (if applicable):  
Current input (ANT, VIDEO 1, etc.)  
If ANT is the current input, either “CABLE” (for cable TV)  
or “ANT” (for over-the-air broadcasts).  
The TV will automatically turn itself off after approximately  
15 minutes if it is tuned to a vacant channel or a station that  
completes its broadcast for the day. This feature functions in  
ANT mode and Built-In DVD mode (No disc) only.  
Channel number (if in ANT mode)  
Channel label (if set)  
Digital signal strength indicator (bar graph in lower right  
corner of box; for ATSC signal only)  
Understanding the last mode  
memory feature  
Stereo, Mono or SAP audio status (when HDMI input mode,  
Dolby Digital or PCM)  
Video resolution  
If the power is cut off while you are viewing the TV, the  
Last Mode Memory feature automatically turns on the TV  
when the power is resupplied.  
Aspect ratio of incoming video signal (4:3 or 16:9)  
V-Chip rating status  
Note: You should unplug the TV’s power cord if it is possible  
that you will be away from the TV for an extended period of time  
after the power is restored.  
12A3N-T456  
16:9  
Stereo SAP  
1080i  
TV-PG  
L
V
.
9:00pm  
ABCHD  
To close the RECALL screen:  
Press E again.  
To display TV status information using INFO:  
Press Q on the remote control.  
The following additional information will display for off air  
digital channels (if applicable):  
Title  
Duration  
Detailed description  
12A3N-T456  
16:9  
Stereo SAP  
1080i  
TV-PG  
L
V
,
East  
MLB Young s XXX...  
,
9:00pm -11:00pm  
ABCHD  
Today s Major League Baseball.  
Note: The location of the banner can be moved to the top or  
bottom of the screen by pressing B or b while the RECALL or  
INFO display is on-screen. (The last position will be stored to  
memory.)  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Using the TV’s advanced features  
Using the static gamma feature  
The static gamma feature allows you to adjust the levels of  
black in the picture.  
Using the advanced picture settings  
features  
To adjust the static gamma settings:  
Using dynamic contrast  
1
2
Press Y and open the Video menu.  
When dynamic contrast is set to Low, Middle, or High, the  
TV will detect changes in the picture quality that affect the  
appearance of your contrast settings and then automatically  
adjust the video.  
Highlight Picture Settings and press T.  
Video  
Mode  
Sports  
Off  
To select dynamic contrast preferences:  
Picture Settings  
Noise Reduction  
1
2
Press Y and open the Video menu.  
Game Mode  
Theater Settings  
Highlight Picture Settings and press T.  
3
4
Highlight Advanced Picture Settings and press T.  
Picture Settings  
Mode: Sports  
Video  
Contrast  
Back Light  
DynaLight  
Brightness  
Color  
100  
100  
Mode  
Sports  
Off  
Picture Settings  
Noise Reduction  
On  
50  
50  
0
Game Mode  
Theater Settings  
Tint  
Sharpness  
50  
Advanced Picture Settings  
3
Highlight Advanced Picture Settings and press T.  
Reset  
Done  
Picture Settings  
Mode: Sports  
In the Static Gamma field, press C or c to adjust the  
static gamma.  
The adjustment range is within 5 from center.  
Contrast  
Back Light  
DynaLight  
Brightness  
Color  
100  
100  
On  
50  
50  
0
Advanced Picture Settings  
Mode: Preference  
Tint  
Dynamic Contrast  
Sharpness  
50  
High  
Static Gamma  
0
Advanced Picture Settings  
Color Temperature  
Cool  
Reset  
Done  
Reset  
Done  
4
In the Dynamic Contrast field, select either Off, Low,  
If the setting is moved in the minus direction, the detail  
of black colors will be decreased.  
If the setting is moved in the plus direction, the detail of  
black colors will be increased.  
Middle or High.  
\
Advanced Picture Settings  
Dynamic Contrast  
Mode: Preference  
Off  
Static Gamma  
0
Color Temperature  
Cool  
5
To save the new settings, highlight Done and press T.  
To revert the factory defaults, highlight Reset and  
press T.  
Reset  
Done  
5
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Note: If you select one of the factory-set picture modes  
(Sports, Standard or Movie) and then change the static  
gamma setting, the picture mode automatically changes  
to Preference.  
Note: If you select one of the factory-set picture modes  
(Sports, Standard, or Movie) and then change the  
dynamic contrast setting, the picture mode automatically  
changes to Preference.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Using the TV’s advanced features  
Selecting the color temperature  
You can change the quality of the picture by selecting from  
three preset color temperatures (Cool, Medium, and Warm), as  
described below.  
Using CableClear® digital noise reduction  
The CableClear® digital noise reduction feature allows you to  
reduce visible interference in your TV picture. This may be  
useful when receiving a broadcast with a weak signal  
(especially a Cable channel) or playing a noisy video cassette  
or disc.  
Mode  
Picture Quality  
blueish  
Cool  
To change the CableClear settings:  
Medium  
Warm  
neutral  
1
2
Press Y and open the Video menu.  
reddish  
Highlight Noise Reduction and press T.  
To select the color temperature:  
1
2
3
4
Press Y and open the Video menu.  
Video  
Mode  
Highlight Picture Settings and press T.  
Highlight Advanced Picture Settings and press T.  
Highlight Color Temperature and press T.  
Sports  
Picture Settings  
Noise Reduction  
Off  
Game Mode  
Theater Settings  
Advanced Picture Settings  
Mode: Preference  
3
In the CableClear field, select your desired setting.  
Dynamic Contrast  
High  
Static Gamma  
0
Noise Reduction  
ANT  
Color Temperature  
Cool  
CableClear  
Auto  
Reset  
Done  
Low  
MPEG Noise Reduction  
Reset  
Done  
5
6
In the Color Temperature field, select the mode you  
prefer (Cool, Medium, or Warm).  
Note:  
Color Temperature  
Mode: Preference  
Cool  
If the current input is ANT, VIDEO 1, or VIDEO 2, the  
menu will display the text “CableClear.” The available  
selections are Off, Auto, Low, Middle, and High.  
If the current input is ColorStream HD1, ColorStream  
HD2, HDMI 1, HDMI 2, or HDMI 3 the menu will display  
the text “DNR.” The available selections are Off, Auto,  
Low, Middle, and High. Auto will react proportionally  
to the strength of the noise. Low, Middle, and High will  
reduce the noise in varying degrees, from lowest to  
highest, respectively.  
Color Temperature  
B Drive  
0
0
G Drive  
Reset  
Done  
Press B or b to select either B Drive or G Drive, and  
then press C or c to adjust the settings.  
B Drive  
G Drive  
1
1
B Drive: c makes the picture blueish.  
G Drive: c makes the picture greenish.  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Note: The B Drive and G Drive settings are connected to  
the Color Temperature settings and will change based  
on which setting is selected in step 5 above.  
7
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Note: If you select one of the factory-set picture modes  
(Sports, Standard, or Movie) and then change the color  
temperature mode, the picture mode automatically  
changes to Preference.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Using the TV’s advanced features  
Using MPEG noise reduction  
Using the Game Mode feature  
The MPEG noise reduction feature allows you to reduce  
visible interference caused by MPEG compression. Choices  
for MPEG noise reduction are Off, Low, Middle, and High.  
Off is automatically selected when this feature is disabled  
(“grayed out”).  
You can use the Game Mode feature for shorter frame delays  
when playing a video game requiring split-second timing  
between the on-screen display and input from the controller  
(such as music creation and high-action games).  
This feature is more effective for 480i and 1080i input signals.  
Note: To use the Game Mode feature, the current video input  
must be Video 1, Video 2, ColorStream HD1,  
ColorStream HD2, HDMI 1, HDMI 2, or HDMI 3. The Game  
Mode cannot be turned on when any other video input is  
selected.  
To select the MPEG noise reduction level:  
1
2
3
Press Y and open the Video menu.  
Highlight Noise Reduction and press T.  
Press B or b to highlight the MPEG Noise Reduction  
field, and then press C or c to select either Off, Low,  
Middle or High.  
To turn on Game Mode:  
1
2
Press Y and open the Video menu.  
Noise Reduction  
ANT  
Press Bor bto highlight the Game Mode field, and then  
press C or c to select On.  
CableClear  
Auto  
Low  
MPEG Noise Reduction  
Reset  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Video  
Mode  
Sports  
Picture Settings  
Noise Reduction  
Off  
Off  
Game Mode  
Theater Settings  
On  
To turn off Game Mode:  
Select Off in step 2 above, change the video input, or turn the  
TV off and then on again.  
Note: You can change the video input by pressing + on the  
remote control (- page 38).  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7: Using the TV’s advanced features  
Using the advanced audio settings  
features  
Using the SRS WOWsurround sound  
feature  
SRS WOWis a special combination of SRS Labs audio  
technologies (SRS 3D, SRS Focus, and SRS TruBass) that  
creates a thrilling surround sound experience with deep, rich  
bass from stereo sound sources. Your TV’s audio will sound  
fuller, richer, and wider.  
To adjust the WOWsettings:  
1
Put the TV in STEREO mode (-“Selecting stereo/SAP  
broadcasts” on page 48).  
2
3
4
Press Y and open the Audio menu.  
Highlight Advanced Audio Settings and press T.  
Press b or B to highlight the WOW feature you want to  
adjust, and then press C or c to adjust the item.  
Advanced Audio Settings  
WOW: SRS 3D  
Off  
Off  
WOW: SRS Focus  
WOW: SRS TruBass  
Low  
Reset  
Done  
WOW: SRS 3D — To turn the surround sound effect  
On or Off.  
Note: If the broadcast is monaural, the SRS 3D effect  
will not work.  
WOW: SRS Focus — To turn the vocal emphasis effect  
On or Off.  
WOW: SRS TruBass — To select the desired bass  
expansion level (Off, Low, or High).  
5
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
WOW, SRS and l symbol are trademarks of SRS Labs, Inc.  
WOW technology is incorporated under license from SRS Labs, Inc.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
Resume feature  
Depending on the disc you are playing, when you press D  
one time, the TV memorizes the location where playback is  
stopped. Press S to resume the playback from the stopped  
location.  
Playing a disc  
Be sure to set the MODE SELECT switch on the remote  
control to TV mode when using the Built-In DVD input.  
If you press D again or eject the disc, the TV will clear the  
stopped location.  
DVD VCD  
CD  
Basic playback  
Auto Play feature  
If you load a disc when the TV is off, the TV will power on and  
playback will commence automatically. However, loading the  
disc may take 1-2 seconds.  
1
Press p on the TV or on the remote control to turn on  
the TV.  
Press + on the remote control or INPUT on the TV to  
select the Built-In DVD mode.  
2
The DVD startup screen will appear on the screen.  
About the Parental Lock screen  
NO DISC  
If the Parental Lock YES/NO screen appears after loading a  
disc and you want to temporarily unlock the Parental Lock,  
select “YES” and then input the PIN CODE following the on-  
screen menu. (The Parental Lock YES/NO screen may be  
repeated two times depending on the disc.)  
Welcome  
3
Load the disc in the disc slot with the label side facing  
forward. (If the disc has a label.) Hold the disc without  
touching either of its surfaces, align it with the guides, and  
place it in position.  
THE PARENTAL LEVEL OF THE  
PLAYER HAS BEEN SET.  
PRESS "YES" TO CONTINUE.  
YES  
STOP  
Note:  
Some unlocked discs may not resume playback after the  
input source has been changed.  
If you stop and restart playback, a message may appear on  
the screen. In this case, please eject the disc and reload it.  
If you are unable to proceed from the Parental Lock screen,  
please eject the disc and reload it.  
Note: When inserting a disc into the DVD disc slot, do not  
jam or force it strongly, otherwise the TV may malfunction  
or the disc might be damaged. If left with half the disc  
inserted, the disc will be loaded automatically.  
CAUTION  
4
“READING” appears on the screen, then playback starts.  
Never insert your finger into the disc hole when loading a  
disc into the disc slot.  
READING  
Keep your fingers well clear of the disc slot when a disc is  
loading or unloading. Neglecting to do so may cause  
personal injury.  
Welcome  
Because of problems and errors that can occur during the  
creation of DVD and CD software and/or the manufacture  
of DVD and CD discs, Toshiba cannot assure that the DVD  
player contained in this television will successfully play  
every disc bearing the DVD and CD logos. If you happen to  
experience any difficulty playing a DVD and/or CD disc on  
the DVD player contained in this television, please contact  
Toshiba Customer Service.  
A menu screen will appear on the TV screen, if the disc  
has a title menu. Press BbCcto select title, then press  
T. Title is selected and play commences.  
5
6
Press z Z to adjust the volume.  
Volume  
16  
Note: When using an amplifier, adjust the volume with the  
amplifier.  
Press D to end playback.  
(continued)  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
Note:  
Note: You cannot adjust the following items while a DVD is  
playing:  
If a non-compatible disc is loaded, “DISK REGION  
INCORRECT” will appear on the TV screen. In this case,  
check your disc again (- page 7).  
Optical Output Format (- page 49)  
Audio Language (- page 48)  
DVD Audio (- page 65)  
Menu Language (- page 32)  
V-Chip (parental control) setting (- page 51)  
DVD Aspect Ratio (- page 63)  
Some discs may take a minute or so to start playback.  
If you insert a single-sided disc the wrong way, “READING”  
will appear on the display for about 30-60 seconds and then  
“BAD DISC” will display until you remove the disc.  
Some discs may not resume playing the same scene after  
stopping.  
Some DVD playback operation may be intentionally fixed by  
the software producers. Since this TV plays DVDs according  
to the disc contents as designed by the software producers,  
some playback features may not be available. Also refer to  
the instructions supplied with the DVDs.  
Do not move the TV during playback. Doing so may damage  
the disc. If you want to move the TV to another place or  
room, be sure to eject the disc and turn off the power  
beforehand.  
If you want to adjust any of the above, stop the DVD by  
pressing D twice, and then adjust (- “Resume feature”).  
Note: Strong static electricity may affect the DVD player’s  
operation and cause it to work improperly. If this happens, turn  
OFF the POWER, disconnect and then reconnect the AC  
power cord, and turn ON the TV again.  
DVD VCD  
CD  
About  
The  
DVD VCD  
CD  
icons on the heading bar show the playable  
If the disc does not load when it is first inserted into the DVD  
disc slot, remove the disc once and try to load the disc  
again.  
Do not put any objects other than discs in the disc slot.  
Doing so may cause the TV to malfunction.  
discs for the function described under that heading.  
DVD  
: You can use this function with DVD video discs.  
VCD  
: You can use this function with Video CDs.  
CD  
: You can use this function with Audio CDs and CD-R/  
RW discs.  
When you press a button, there may be a slight delay before  
the function activates.  
To start playback from stop mode:  
Press S.  
To pause playback (still mode):  
Press A during playback.  
To resume normal playback, press S.  
Note: The sound is muted during still mode.  
To stop playback:  
Press D.  
To remove the disc:  
1
2
Press d on the remote control or OPEN/CLOSE on the  
TV. The disc will come out halfway.  
Press d again to remove the disc or press S to play  
again.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
Using the DVD aspect ratio feature  
When you view a DVD from the Built-In DVD input, you can  
select the DVD aspect ratio, as described below.  
4:3 Pan Scan: Black bars are visible on right and left sides  
of the screen.  
Playing in fast reverse or fast  
DVD VCD CD  
forward  
Press H or J during playback.  
H: Fast reverse playback (DVD/VCD: 2X-64X, CD/MP3:  
2X-16X)  
J: Fast forward playback (DVD/VCD: 2X-64X, CD/MP3:  
2X-16X)  
Each time you press H or J , the playback speed changes.  
Picture where both sides of  
the original wide screen  
image are cropped.  
4:3 Letter Box: The picture is stretched wider and taller to  
fill the screen.  
DVD VCD  
CD  
To resume normal playback:  
Press S.  
Note:  
The TV mutes sound and subtitles during reverse and  
forward scan of DVD video discs. However, the TV plays  
sound during fast forward or fast reverse play of audio CDs.  
A B C D E F G - - - - - - - - - - - - - - - -  
Letter box picture  
The playback speed may differ depending on the disc.  
16:9 Wide: The picture is stretched wider to fill the width  
of the screen.  
To pause playback (still playback)  
DVD VCD  
CD  
Press A during playback.  
Squeezed picture  
To select the DVD aspect ratio:  
1
2
3
Press Y and open the Video menu.  
Highlight Theater Settings and press T.  
To resume normal playback:  
Press S.  
In the DVD Aspect Ratio field, select the mode you  
prefer (4:3 Pan Scan, 4:3 Letter Box, or 16:9 Wide).  
Note: The sound is muted during still playback.  
Theater Settings  
Picture Size  
Natural  
Picture Scroll  
--  
Cinema Mode  
Film  
On  
Auto Aspect Ratio  
DVD Aspect Ratio  
16:9 Wide  
Reset  
Done  
4
To save the new settings, highlight Done and press T.  
To revert to the factory defaults, highlight Reset and  
press T.  
Note: You cannot change the DVD aspect ratio while you are  
viewing a DVD. (You must be in FULL-STOP mode, not  
RESUME-STOP mode.)  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
DVD  
DVD VCD  
Playing frame by frame  
Changing angles  
Press A during still playback.  
Each time you press A, the picture advances one frame.  
You can change the viewing angle of the scene during  
playback if the disc is recorded with multi-angle facility.  
1
2
Press a during playback.  
The current angle will appear.  
To resume normal playback:  
Press S.  
Press a repeatedly until the desired angle is selected.  
Note: The sound is muted during frame by frame playback.  
Note: Depending on the DVD, you may not be able to change  
the angles even if multi-angles are recorded on the DVD.  
DVD VCD  
Playing in slow motion  
DVD  
Title selection  
Press v or V during playback.  
Each time you press the button, the slow-motion speed  
changes (DVD/VCD: 1/32-1/2).  
Two or more titles are recorded on some discs. If the title menu  
is recorded on the disc, you can select the desired title.  
1
Press N during playback.  
Title menu appears on the screen.  
2
3
Press B b C c to select the desired title.  
Press T or S.  
The playback of the selected title will start.  
To resume normal playback:  
Press S.  
Note:  
Depending on the DVD, you may not be able to select the  
title.  
Depending on the DVD, a “title menu” may simply be called  
a “menu” or “title” in the instructions supplied with the disc.  
Note:  
The sound is muted during slow-motion playback.  
V is not available for the VCD disc.  
Depending on the DVD, the title menu may be displayed  
automatically when the disc is loaded.  
Depending on the DVD, a chapter menu may be displayed  
after you select a title.  
DVD VCD  
CD  
Locating a chapter or track  
Press F or G repeatedly to select the chapter or track you  
want.  
Playback starts from beginning of the selected chapter or track.  
Note: A “Prohibition” symbol  
may appear at the upper right  
of the screen. This symbol means either the feature you tried is  
not available on the disc, or the TV cannot access the feature  
at this time. This does not indicate a problem with the TV.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
Note:  
If the desired language is not heard after pressing the button  
several times, the language is not recorded on the disc.  
Changing soundtrack language  
DVD VCD  
Changing soundtrack language is cancelled when you eject  
the disc. The initial default language or available language  
will be heard if the disc is played back again.  
You can select the language when you play a multilingual disc.  
If you select DTS in playing DTS-encoded disc, no sound  
1
2
Press c during playback.  
The current soundtrack language will appear.  
will be heard from the TV’s speakers.  
AUDIO 1 / 4 : ENG  
D 5 . 1  
DVD  
Subtitles  
When playing back a disc recorded with subtitles, you can  
select the subtitle language or turn the subtitle off.  
Press c repeatedly until the desired language is selected.  
The on-screen display will disappear after a few  
seconds.  
1
Press b repeatedly during playback until your desired  
language appears.  
SUBTITLE 02 / 02 : FRE  
AUDIO 2 / 4 : FRE  
D 5 . 1  
2
To turn off the subtitle, press b until “SUBTITLE OFF”  
appears.  
In case of Video CD playback  
The “SUBTITLE OFF” on-screen display will  
disappear after a few seconds.  
1
2
3
Stop the disc playback.  
SUBTITLE OFF  
Press Y and open the Audio menu.  
Highlight Audio Setup and press T.  
Audio  
Digital Audio Selector  
Note:  
Depending on the DVD, you may not be able to change  
subtitles, or to turn subtitles on or off.  
While playing a DVD, the subtitles may turn on or off when  
Audio Settings  
Advanced Audio Settings  
Audio Setup  
you load or eject the disc.  
In some cases, a selected subtitle language may not be  
changed immediately.  
4
Press B or b to highlight DVD Audio, and then press C  
or cto select the desired audio mode (Stereo, L-Mono,  
R-Mono, or MIX-Mono).  
Note: This item may not be selectable depending on the  
disc.  
Audio Setup  
PC Audio  
No  
Auto  
HDMI 1 Audio  
MTS  
Stereo  
Language  
English  
Optical Output Format  
Dolby Digital/Surround  
Dolby Digital  
Dynamic Range Control  
Compressed  
Stereo  
DVD Audio  
Reset  
Done  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
DVD VCD  
CD  
Disc status  
MP3/JPEG CD operation  
With each press of E, the status of the disc will appear on  
the screen and change as follows:  
This TV can play MP3/JPEG-data which has been recorded on  
CD-R or CD-RW.  
To produce MP3/JPEG-data, you need a Windows-PC with  
CD-R/RW drive and MP3/JPEG-encoding Software (not  
supplied).  
Files recorded on an Apple® HFS (hierarchical file system)  
volume cannot be played.  
Display example  
DVD  
MP3 Files  
TITLE / CHAPTER  
CHAPTER ELAPSED  
FILE ELAPSED  
Apple is a registered trademark of Apple Computer, Inc.  
FILE REMAIN  
OFF  
CHAPTER REMAIN  
TITLE ELAPSED  
TITLE REMAIN  
OFF  
VCD  
MP3/JPEG CD information  
Limitations on MP3/JPEG CD playback  
MP3/JPEG CDs must meet ISO9660 standards. Files must  
have one of the following extensions: .mp3, or .jpg.  
MP3/JPEG CDs cannot be used for the purpose of  
recording.  
If the CD has both audio tracks and MP3/JPEG files, only  
audio tracks are played.  
CD  
TRACK **/**  
TRACK ELAPSED  
VCD  
TRACK REMAIN  
DISC ELAPSED  
DISC REMAIN  
OFF  
TRACK **/**  
TRACK ELAPSED  
TRACK REMAIN  
OFF  
It may take more than 1 minute for this TV to read MP3/  
JPEG files depending on its structure.  
Note:  
Some MP3/JPEG CDs cannot be played back depending on  
the recording conditions.  
The CD-R/RWs that has no music data or non MP3/JPEG  
files cannot be played back.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
Note:  
CD  
MP3 CD playback  
The DIGITAL AUDIO OUT terminal on the TV outputs MP3  
sounds in the linear PCM format regardless of the current  
“Optical Output Format” selection.  
1
2
Load a disc on which MP3 files have been recorded in the  
disc slot.  
The DVD player contained in this television requires discs/  
recordings to meet certain technical standards in order to  
achieve optimal playback quality. There are many different  
types of recordable disc formats (including CD-R containing  
MP3/WMA files). Not all recordable discs will operate or  
produce optimal playback quality. The technical criteria set  
forth in this owner's manual are meant only as a guide. Use  
of CD-RW for MP3 files is not recommended.  
A file menu screen will appear on the screen. Press B or  
b to select a folder and then press T to open the folder.  
F i l e E l a p s e d 0 0 : 0 0 : 0 0  
CD-ROM  
ROOT  
100TOSHIBA  
101TOSHIBA  
You must obtain any required permission from copyright  
owners to download or use copyrighted content. Toshiba  
cannot and does not grant such permission.  
About the menu icons  
3
4
Press BbC c to highlight the desired file. The selected  
file is highlighted in blue.  
: Indicates MP3 file  
: Indicates JPEG file  
Note: To return to the previous menu, press {.  
Note:  
F i l e E l a p s e d 0 0 : 0 0 : 0 0  
The slide show will start automatically when the FUJICOLOR  
CD or the Kodak Picture CD is played. Pressing D displays  
thumbnail view.  
However, depending on the recording conditions, those  
discs may not operate properly.  
MP3 files on the Kodak Picture CD are not recognized on  
this TV.  
CD-ROM  
ROOT/100TOSHIBA  
001 TDCFILE....  
002 TDCFILE  
003 TDCFILE  
004 TDCFILE  
005 TDCFILE  
006 TDCFILE  
007 TDCFILE  
ROOT  
001 TDCFILE....  
When displaying the MP3/JPEG files, use the Natural or Full  
picture size (- page 42).  
Press S (the file is highlighted in yellow).  
F i l e E l a p s e d 0 0 : 0 1 : 3 8  
CD-ROM  
ROOT/100TOSHIBA  
001 TDCFILE....  
002 TDCFILE  
003 TDCFILE  
004 TDCFILE  
005 TDCFILE  
006 TDCFILE  
007 TDCFILE  
ROOT  
001 TDCFILE....  
The selected file starts playing back.  
To advance to the next MP3 file, press G.  
To return to the previous MP3 file, press F.  
To restart the playing MP3 file, press T.  
For fast reverse playback, press H.  
For fast forward playback, press J.  
5
Press D to end playback (the file is highlighted in  
yellow).  
The TV records the stopped point where playback  
ended. Press S to resume playback (from the same  
point).  
If you press D again (the file is highlighted in blue) or  
unload the disc, the TV will clear the stopped point.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 8: DVD Playback  
CD  
JPEG CD playback  
You can select your desired JPEG file from the file menu. The  
slide show enables you to view pictures (files) one after  
another automatically.  
1
2
Load a disc on which JPEG files have been recorded in the  
disc slot.  
A file menu screen will appear. Press B or b to select a  
folder and then press T to open the folder.  
F i l e E l a p s e d 0 0 : 0 0 : 0 0  
CD-ROM  
ROOT  
100TOSHIBA  
101TOSHIBA  
3
Press BbC c to select the desired file.  
F i l e E l a p s e d 0 0 : 0 0 : 0 0  
CD-ROM  
ROOT/101TOSHIBA  
001 TDCFILE....  
002 TDCFILE  
003 TDCFILE  
004 TDCFILE  
005 TDCFILE  
006 TDCFILE  
007 TDCFILE  
4
5
Press S to start the slide show from the selected file.  
If you playback the selected file only, press T. While the  
picture is on-screen, you can rotate the picture by 90°  
using BbC c buttons.  
Press D to end playback. The file menu will appear on  
the screen. If you want to view another file, repeat  
steps 3–4.  
If you press A during the slide show, the slide  
show stops temporarily. “PAUSE” appears on the  
screen. Press S again to resume the slide show.  
To display the next file, press G.  
To display the previous file, press F.  
When slide show playback has finished, the file list  
appears.  
To stop the slide show, press D. The file list will  
appear.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: Troubleshooting  
Cannot view external signals or channel 3 or 4  
General troubleshooting  
If you cannot view signals from external devices  
connected to VIDEO 1, VIDEO 2, ColorStream®,  
HDMI 1, HDMI 2, PCor from channels 3 or 4, make sure  
the Input Lock is set to Off (- page 53).  
Before calling a service technician, please check this chapter  
for a possible cause of the problem and some solutions you can  
try.  
Poor color or no color  
The station may have broadcast difficulties. Try another  
channel.  
Black box on-screen  
Adjust the Tint and/or Color (- page 45).  
The closed caption feature is set to one of the Text modes  
(T1, T2, T3, or T4). Set the closed caption feature to Off  
(- page 46).  
Poor composite or S-video picture  
If the TV is connected to an external A/V device (e.g.,  
DVD player, video game system, set-top box, etc.) try  
using a ColorStream or HDMI video connection  
instead.  
TV stops responding to controls  
If the TV stops responding to the controls on the remote  
control or TV control panel and you cannot turn off the  
TV, press and hold the POWERbutton on the TV control  
panel for 5 or more seconds to reset the TV.  
Picture and sound are out of sync  
As with all products that contain a digital display, in rare  
instances, when viewing certain content (e.g.. television  
broadcasts, video games, DVDs), you may notice that the  
sound and picture are slightly out of sync. This  
phenomenon can be caused by various factors including,  
without limitation, video processing within the TV, video  
processing in an attached gaming system, and video  
processing or different compression rates used by  
broadcasters in their programming. You may want to try  
one or more of the following suggestions, which may  
help to reduce the effect of this phenomenon:  
Other problems  
If your TV’s problem is not addressed in this  
Troubleshooting section or the recommended solution  
has not worked, use the Restore Factory Defaults  
procedure (- page 37).  
TV will not turn on  
Make sure the power cord is plugged in, and then press  
p.  
The remote control batteries may be dead. Replace the  
– If the TV is connected to an A/V receiver that has a  
programmable audio delay feature, use this feature to  
help synchronize the sound to the picture.  
batteries or try the control panel buttons.  
– If you notice this phenomenon only on certain TV  
channels, please contact your local broadcast, cable, or  
satellite provider to inform them of this issue.  
Picture problems  
General picture problems  
Check the antenna/cable connections (- Chapter 2).  
Press + on the remote control or TV and select a valid  
video input source (- page 38). If no device is  
connected to a particular input on the TV, no picture will  
display when you select that particular input source. For  
device connection details, see Chapter 2.  
Antenna reception may be poor. Use a highly directional  
outdoor antenna (if applicable).  
The station may have broadcast difficulties. Try another  
channel.  
Adjust the picture qualities (- page 45).  
If you are using a VCR, make sure l on the remote  
control is set correctly (- page 25).  
LED indications while in reboot from standby  
When you plug the power cord in, the yellow LED will  
blink until the TV enters standby mode, (plugged in but  
not powered on). This is normal and is not a sign of  
malfunction.  
Sound problems  
Check the antenna/cable connections (- Chapter 2).  
The station may have broadcast difficulties. Try another  
channel.  
The sound may be muted. Press VOLUME.  
If you hear no sound, try setting the MTS feature to  
Stereo mode (- page 48).  
If you are not receiving a second audio program from a  
known SAP source, make sure the MTS feature is set to  
SAP mode (- page 48).  
Do not connect both a standard video cable and an  
S-video cable to the VIDEO 1 input at the same time  
(- page 17).  
Noisy picture  
If you hear audio that seems “incorrect” for the program  
you are watching (such as music or a foreign language),  
the SAP mode may be on. Set the MTS feature to Stereo  
mode (- page 48).  
If you are watching an analog channel (off-air broadcast  
or Cable TV), you can set the CableClear®/DNR  
feature to AUTO to reduce visible interference in the TV  
picture (- page 58).  
Video Input Selection problems  
Remote control problems  
If the Input Selection window does not appear when  
you press + on the remote control or TV, press + a  
second time, which will change to the next video input  
source and display the Input Selection window.  
Make sure the remote control is set to the correct device  
mode (- page 24).  
Remove all obstructions between the remote control and  
the TV.  
The remote control batteries may be dead. Replace the  
batteries (- page 23).  
(continued)  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: Troubleshooting  
Your TV remote control may not operate certain features  
on your external device. Refer to the owner’s manual for  
your other device to determine its available features. If  
your TV remote control does not operate a specific  
feature on another device, use the remote control that  
came with the device (- pages 25–29).  
If the TV still does not act as expected, use the Reset  
Factory Defaults procedure (- page 37).  
DVD Troubleshooting  
Playback doesn’t start  
The disc is reversed. Load the disc with the playback side  
facing backward.  
No disc is loaded. Load the playable disc.  
The disc may be dirty. Clean the disc.  
The TV cannot play CD-ROMs, etc. Load a playable  
disc.  
Channel tuning problems  
Make sure the remote control is set to the correct device  
mode (- page 24).  
No picture  
TV selector is not set correctly.  
The channel may have been erased from the channel  
memory by the Channel Add/Delete feature. Add the  
channel to the channel memory (- page 33).  
The channel may be blocked by the Channels Block  
feature. Unblock the channel (- page 52).  
If you are unable to tune digital channels, check the  
antenna configuration (- page 32). If you are still  
unable to tune digital channels, clear all channels from  
the channel list (- page 34) and reprogram channels  
into the channel memory (- page 33). If you are still  
unable to tune digital channels, use the Reset Factory  
Defaults procedure (- page 37). Also see “TV stops  
responding to controls” and “Other problems”  
(- page 69).  
No sound  
The analog audio output terminals on the TV do not  
output the sounds from the disc. Connect your digital  
audio system to the DIGITAL AUDIO OUT terminal on  
the TV.  
Make sure the input selector of the amplifier is set  
properly.  
The TV is in the special playback mode.  
Picture is distorted during fast reverse/forward playback  
The picture will be distorted occasionally.  
Stopping playback, search, slow-motion play, or  
changing angles, etc. cannot be performed  
Some discs may not perform certain functions.  
Closed caption problems  
No surround sound  
If the program or video you selected is not closed-  
captioned, no captions will display (- page 46).  
If text is not available, a black rectangle may appear.  
If this happens, turn off the closed caption feature (-  
page 46).  
A closed-caption signal may not display correctly in the  
following situations: a) when a videotape has been  
dubbed; b) when the signal reception is weak; or c) when  
the signal reception is nonstandard (- page 46).  
The setup may not match your stereo system.  
The TV or remote operation key is not functioning  
Turn off the TV and unplug the AC power cord for  
several minutes, then replug it.  
Audio soundtrack and/or subtitle language is not  
changed when you play back a DVD  
Multilingual language is not recorded on the DVD disc.  
No subtitle  
Some discs have no subtitles.  
Subtitles are cleared. Press b.  
Rating blocking (V-Chip) problems  
If you forget your PIN code: While the PIN code entering  
screen is displayed, press E four times within 5  
seconds. The PIN code you previously stored will be  
cleared (- page 50).  
Angle cannot be changed  
Multi-angles are not recorded on the DVD discs.  
appears on the screen  
The function is prohibited with the TV or the disc.  
The V-Chip feature is available for the U.S. V-Chip  
system only (- page 51).  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9: Troubleshooting  
LED indications  
The green and yellow LED lights on the TV front indicate the TV’s status, as described below.  
Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow  
LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction.  
TV front  
DISC  
POWER  
Yellow LED Green LED  
LED Indication  
Condition  
Solution  
1) Green is ON (solid).  
2) Yellow is ON (solid).  
The TV is operating properly.  
A disc is in the disc slot.  
TV is powering up.  
3) Yellow blinks three  
times.  
Wait several seconds until the yellow LED stops  
blinking.  
4) Green blinks slowly.  
Abnormal operation of BUS line.  
Power protect detection.  
Turn OFF the TV and unplug the power cord.  
Plug the power cord in again and turn ON the TV.  
5) Green blinks  
quickly.  
If, after trying the solutions, the problem still exists:  
In the U.S., call TACP Consumer Solutions at 1-800-575-5469.  
In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click  
“Home Entertainment,” and then click “Support.”  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10: Appendix  
HDMI™ INPUT:  
HDMI compliant (type A connector)  
HDCP compliant  
Specifications  
Note:  
Audio Lip Sync supported  
This model complies with the specifications listed  
below.  
Suggested formats: See table below  
HDMI Audio: 2-channel L-PCM; 32/44.1/48 kHz  
sampling frequency; 16/20/24 bits per sample  
Designs and specifications are subject to change  
without notice.  
FIXED AUDIO OUTPUT:  
150 mv (rms) (30% modulation equivalent, 2.2 k ohm  
or less)  
This model may not be compatible with features and/or  
specifications that may be added in the future.  
DIGITAL AUDIO OUTPUT:  
Television System  
Optical type  
NTSC standard  
PC INPUT:  
ATSC standard (8VSB)  
Digital Cable (64 QAM, 256 QAM; in-the-clear,  
unencrypted)  
15-Pin D-sub Analog RGB  
DVD/CD Player  
DVD signal system NTSC  
DVD region number 1  
Applicable disc 1. DVD (12cm, 8cm [with Disc adapter])  
Channel Coverage  
VHF: 2 through 13  
UHF: 14 through 69  
Cable TV: Mid band (A-8 through A-1, A through I)  
Super band (J through W)  
2. CD (12cm, 8cm [with Disc adapter])  
1-Lens, 2-Beams system  
Pickup  
Hyper band (AA through ZZ, AAA, BBB)  
Ultra band (65 through 94, 100 through 135)  
Dimensions  
26LV67: Width: 26-1/4 inches (666 mm)  
Height: 20-1/4 inches (514 mm)  
Depth: 9-1/2 inches (241 mm)  
32LV67/32LV67U:  
Power Source: 120 V AC, 60 Hz  
Power Consumption  
26LV67: 80 W (average)  
16.0 W in standby mode  
32LV67/32LV67U:  
Width: 31-1/2 inches (800 mm)  
Height: 23-3/8 inches (592 mm)  
Depth: 11-1/4 inches (285 mm)  
105 W (average)  
16.0 W in standby mode  
Mass (weight)  
26LV67: 30.0 lbs (13.6 kg)  
32LV67: 40.3 lbs (18.3 kg)  
32LV67U: 40.3 lbs (18.3 kg)  
Audio Power: 10 W + 10 W  
Speaker Type: Two 2-3/8 × 4-3/4 inches (6 × 12 cm)  
Video/Audio Terminals  
Operating conditions  
S-VIDEO INPUT:  
Y: 1 V(p-p), 75 ohm, negative sync.  
C: 0.286 V(p-p) (burst signal), 75 ohm  
Temperature: 32ºF - 95ºF (0ºC - 35ºC)  
Humidity: 20 - 80% (no moisture condensation)  
Supplied Accessories  
VIDEO/AUDIO INPUT:  
VIDEO: 1 V(p-p), 75 ohm, negative sync.  
AUDIO: 150 mV(rms) (30% modulation equivalent, 22 k  
ohm or greater)  
• Remote control with two size “AAA” batteries  
• Owner’s manual (this book)  
• Lead clip  
ColorStream® (component video) HD INPUT:  
VIDEO:Y: 1V(p-p), 75 ohm  
Use this clip to attach the TV to a wall, pillar, or other  
immovable structure. See item 20 on page 3.  
PR: 0.7 V(p-p), 75 ohm  
PB: 0.7 V(p-p), 75 ohm  
Suggested formats: 1080i, 720p, 480p, 480i  
AUDIO: 150 mV(rms), 22 k ohm or greater  
HDMI input supports the following signal formats:  
p
Format  
VGA  
480i  
Resolution  
640 x 480p  
720 x 480i  
V. Frequency  
59.940/60Hz  
59.940/60Hz  
59.940/60Hz  
59.940/60Hz  
59.940/60Hs  
23.976/24Hz  
59.940/60Hz  
H. Frequency  
Pixel Clock Frequency  
25.175/25.200MHz  
27.000/27.027MHz  
27.000/27.027MHz  
74.176/74.250MHz  
74.176/74.250MHz  
74.176/74.250MHz  
148.352/148.500MHz  
31.469/31.500kHz  
15.734/15.750kHz  
31.469/31.500kHz  
44.955/45.000kHz  
33.716/33.750kHz  
26.973/27.000kHz  
67.433/67.500kHz  
480p  
720 x 480p  
720 x 480p  
1920 × 1080i  
1920 × 1080p  
1920 × 1080p  
720p  
1080i  
1080p  
1080p  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10: Appendix  
not covered by this warranty. Reception problems caused by  
inadequate antenna systems, misaligned satellite dishes, cable  
television distribution, VCRs, DVD players/recorders, personal  
computer level IEEE-1394 devices, and any other connected signal  
source device are your responsibility.  
Limited United States Warranty  
for LCD TV/DVD Combinations 26” and Larger  
(5) Warranties extend only to defects in materials or workmanship as  
limited above, and do not extend to any LCD TV/DVD Combination or  
parts that have been lost or discarded by you or to damage to the  
LCD TV/DVD Combination or parts caused by fires, misuse, accident,  
Acts of God (such as lightning or fluctuations in electric power),  
improper installation, improper maintenance, or use in violation of  
instructions furnished by TACP; use or malfunction through  
simultaneous use of this LCD TV/DVD Combination and connected  
equipment; or to units that have been modified or had the serial  
number removed, altered, defaced, or rendered illegible.  
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the  
following limited warranties to original consumers in the United States.  
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL  
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD  
TV/DVD COMBINATION AS A GIFT FROM THE ORIGINAL CONSUMER  
PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.  
LCD TV/DVD COMBINATIONS PURCHASED IN THE U.S.A. AND USED  
ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT  
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE  
WARRANTIES.  
LCD TV/DVD COMBINATIONS PURCHASED ANYWHERE OUTSIDE  
OF THE U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND  
MEXICO, AND USED IN THE U.S.A., ARE NOT COVERED BY THESE  
WARRANTIES.  
How to Obtain Warranty Service  
If, after following all of the operating instructions in this manual and  
reviewing the section entitled “Troubleshooting,” you find that service is  
needed:  
(1) To find the nearest TACP Authorized Service Station, visit TACP’s  
website at www.tacp.toshiba.com/service or contact TACP’s  
Consumer Solution Center toll free at 1-800-575-5469.  
(2) You must present your original bill of sale or other proof of purchase  
to the TACP Authorized Service Station.  
Limited One (1) Year Warranty on Parts and Labor  
TACP warrants this LCD TV/DVD Combination and its parts against  
defects in materials or workmanship for a period of one (1) year after the  
date of original retail purchase. DURING THIS PERIOD, TACP WILL, AT  
TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A  
NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU FOR  
PARTS OR LABOR. During this period, TACP Authorized Service Station  
personnel will come to your home when warranty service is required.  
Depending on the type of repair required, the service will either be  
performed in your home or the LCD TV/DVD Combination will be taken to  
a TACP Authorized Service Station for repair and returned to your home at  
no cost to you.  
For additional information, visit TACP’s website:  
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE  
U.S.A., INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,  
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED  
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY  
WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.  
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE  
AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,  
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH  
RESPECT TOTHE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO  
EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR  
INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST  
PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR  
ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR  
INABILITY TO USE THIS LCD TV/DVD COMBINATION).  
Rental Units  
The warranty for LCD TV/DVD Combination rental units begins on the date  
of the first rental or thirty (30) days after the date of shipment to the rental  
firm, whichever comes first.  
Limited Warranty for Commercial Units  
TACP warrants LCD TV/DVD Combinations that are sold and used for  
commercial purposes as follows: all parts are warranted against defects  
in materials or workmanship for a period of ninety (90) days after the date  
of original retail purchase. DURING THIS PERIOD, TACP WILL, AT  
TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A  
NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU.  
No person, agent, distributor, dealer, or company is authorized to change,  
modify, or extend the terms of these warranties in any manner whatsoever.  
The time within which an action must be commenced to enforce any  
obligation of TACP arising under the warranty or under any statute or law  
of the United States or any state thereof is hereby limited to ninety (90)  
days from the date you discover, or should have discovered, the defect.  
This limitation does not apply to implied warranties arising under the law  
of any state of the U.S.A.  
Owner’s Manual and Product Registration Card  
Read this owner’s manual thoroughly before operating this LCD TV/DVD  
Combination.  
Complete and mail the enclosed product registration card or register your  
LCD TV/DVD Combination online at www.tacp.toshiba.com/service  
as soon as possible. By registering your LCD TV/DVD Combination you  
will enable TACP to bring you new products specifically designed to meet  
your needs and help us to contact you in the unlikely event a safety  
notification is required under the U.S. Consumer Product Safety Act.  
Failure to complete and return the product registration card  
does not diminish your warranty rights.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU  
MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE  
TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT  
ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED  
WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE  
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY  
TO YOU UNDER SUCH CIRCUMSTANCES.  
Your Responsibility  
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING  
CONDITIONS:  
(1) You must retain your original bill of sale or provide other proof of  
purchase.  
(2) All warranty servicing of this LCD TV/DVD Combination must be  
performed by an Authorized TACP Service Station.  
(3) The warranties from TACP are effective only if this LCD TV/DVD  
Combination is purchased and operated in the Continental U.S.A. or  
Puerto Rico.  
(4) Labor service charges for set installation, setup, adjustment of  
customer controls, and installation or repair of antenna systems are  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10: Appendix  
(d) FOR TELEVISIONS OVER OVER 32 INCHES: During this period, ASP  
personnel will come on-site when warranty service is required.  
Depending on the type of repair required, the service will either be  
performed on-site or the Television will be taken to an ASP for repair  
and returned at no cost to you. ON-SITE SERVICE ONLY APPLIES  
WITHIN 100 KILOMETERS OF AN ASP. IF YOU ARE NOT WITHIN  
100 KILOMETERS OF AN ASP, YOU MUST DELIVER THE ENTIRE  
TELEVISION TO AN ASP. YOU MUST PAY FOR ALL  
Limited Canadian Warranty  
for Toshiba Brand Flat Panel Televisions  
Toshiba of Canada Limited (“TCL”) makes the following limited warranties  
to original consumers in Canada. THESE LIMITED WARRANTIES  
EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY  
PERSON RECEIVING THIS TOSHIBA BRAND FLAT PANEL  
TELEVISION (the “TELEVISION(S)” or “Television(s)”) AS A GIFT FROM  
THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER  
PURCHASER OR TRANSFEREE.  
TRANSPORTATION AND INSURANCE CHARGES FOR THE  
TELEVISION TO AND FROM THE ASP.  
Rental Units  
The warranty for Television rental units begins with the date of first rental  
or thirty (30) days from the date of shipment to the rental firm, whichever  
comes first.  
TELEVISIONS PURCHASED IN CANADA, AND USED ANYWHERE  
OUTSIDE OF CANADA INCLUDING, WITHOUT LIMITATION, THE  
UNITED STATES AND MEXICO, ARE NOT COVERED BY THESE  
WARRANTIES.  
Your Responsibility  
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING  
CONDITIONS:  
TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF CANADA,  
INCLUDING, WITHOUT LIMITATION, THE UNITED STATES AND  
MEXICO, AND USED IN CANADA, ARE NOT COVERED BY THESE  
WARRANTIES.  
(1) You must provide your bill of sale or other proof of purchase.  
(2) All warranty servicing of this Television must be performed by an ASP.  
(3) The warranties from TCL are effective only if the Television is (i)  
purchased as new and unopened from TCL or from TCL’s authorized  
distributors, dealers or resellers (“ADR’s”) and (ii) located/operated in  
Canada.  
(4) Labour charges for set installation, setup, adjustment of customer  
controls, and installation or repair of antenna systems are not covered  
by these warranties. Reception problems caused by inadequate  
antenna systems are your responsibility.  
(5) Warranties extend only to material defects in materials or  
workmanship as limited above, and do not extend to:  
a. Service, repairs or replacement made necessary by accident,  
misuse, abuse, moisture, liquids, dust, dirt, neglect, accident,  
damage, 24/7 applications, improper installation, improper  
operation, improper cleaning, improper maintenance, normal  
wear and tear, screen burn or image retention caused by  
prolonged display of static images and/or phosphor aging, or any  
other external cause or event, act or omission outside the control  
of TCL, including fire, theft, acts of God, alteration, power failures,  
power surges or power shortages, lightning, other electrical  
faults, or repairs, modifications or replacements by persons other  
than those authorized by TCL to service the Television;  
b. Replacement of missing, discarded or lost parts, the provision of  
retrofits, or preventive maintenance;  
Limited One (1) Year Warranty on Parts and Labour  
Subject to the more limited warranty if the Television is used for any  
commercial or business purposes as set out below, TCL warrants the  
Television and its parts against material defects in materials or  
workmanship that result in the Television failing for a period of one (1) year  
after the date of original retail purchase. DURING THIS PERIOD, TCL  
WILL, AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART  
WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU  
FOR PARTS OR LABOUR.  
(a) FOR TELEVISIONS 32 INCHES OR LESS: YOU MUST DELIVER THE  
ENTIRE TELEVISION TO A TCL TELEVISION AUTHORIZED  
SERVICE PROVIDER (“ASP”). YOU MUST PAY FOR ALL  
TRANSPORTATION AND INSURANCE CHARGES FOR THE  
TELEVISION TO AND FROM THE ASP.  
(b) FOR TELEVISIONS OVER 32 INCHES: During this period, ASP  
personnel will come to your home when warranty service is required.  
Depending on the type of repair required, the service will either be  
performed in your home or the Television will be taken to an ASP for  
repair and returned to your home at no cost to you. IN-HOME  
SERVICE ONLY APPLIES WITHIN 100 KILOMETERS OF AN ASP.  
IF YOU ARE NOT WITHIN 100 KILOMETERS OF AN ASP, YOU  
MUST DELIVER THE ENTIRE TELEVISION TO AN ASP. YOU MUST  
PAY FOR ALL TRANSPORTATION AND INSURANCE CHARGES  
FOR THE TELEVISION TO AND FROM THE ASP.  
c. Repair of damage that is cosmetic only or does not affect the  
Television functionality, such as wear and tear, scratches and  
dents;  
d. Service on Toshiba-branded accessory items (such accessory  
items may be covered by their own warranty);  
e. Service on third party products or service made necessary by  
use of incompatible third party products;  
f. Service made necessary by the simultaneous use of this  
Television and connected equipment;  
g. Modifications to the Television not approved in writing by TCL,  
and service made necessary by the use or installation of non-  
Toshiba modifications to the Television;  
Limited Warranty for Commercial Units  
TCL warrants Televisions that are used for any commercial or business  
purposes as follows: all parts are warranted against material defects in  
materials or workmanship that result in the Television failing for a period of  
ninety (90) days after the date of original retail purchase. DURING THIS  
PERIOD, TCL WILL, AT TCL’S OPTION, REPAIR OR REPLACE THE  
DEFECTIVE PART WITH A NEW OR REFURBISHED PART WITHOUT  
CHARGE TO YOU.  
(c) FOR TELEVISIONS 32 INCHES OR LESS: YOU MUST DELIVER THE  
ENTIRE TELEVISION TO AN ASP. YOU MUST PAY FOR ALL  
TRANSPORTATION AND INSURANCE CHARGES FOR THE  
TELEVISION TO AND FROM THE ASP.  
h. Service of a Television on which the TOSHIBA label or logo, rating  
label or serial number have been defaced or removed;  
i. On-site service and repair of the Television; and  
j. Damage to the Television caused by failure to follow the  
specifications, User manuals or guides as to usage and/or  
storage.  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10: Appendix  
Disclaimer and Limitation of Remedy  
agree to opt out of any such representative or class proceedings.  
Arbitration of any Dispute will be conducted in the forum and in the  
manner as agreed to between you and TCL. Failing such agreement, the  
arbitration will be conducted by one arbitrator pursuant to the laws and  
rules relating to arbitration generally in force in the jurisdiction in which you  
reside at the time that the Dispute arises. To the extent not precluded by  
law, no claim, dispute, controversy or disagreement of any other person  
may be joined or combined with any Dispute by you, without the prior  
written consent of TCL.  
TO THE EXTENT NOT PRECLUDED BY LAW, ALL OTHER EXPRESS  
AND IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS  
FOR THIS TELEVISION, INCLUDING THE IMPLIED WARRANTIES,  
CONDITIONS AND REPRESENTATIONS OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED  
AND EXCLUDED. IF THE APPLICABLE LAW, STATUTORY OR  
OTHERWISE, PRECLUDES THE EXCLUSION OF ANY IMPLIED  
WARRANTIES, CONDITIONS AND REPRESENTATIONS THEN SUCH  
IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS ARE  
OTHERWISE LIMITED IN DURATION TO THE TERM OF THIS  
EXPRESS WRITTEN LIMITED WARRANTY. TO THE EXTENT NOT  
PRECLUDED BY LAW, STATUTORY OR OTHERWISE, THIS WRITTEN  
WARRANTY SUPERCEDES AND SPECIFICALLY DISCLAIMS ANY  
OTHER WARRANTY, CONDITION OR REPRESENTATION NOT  
STATED IN THIS WARRANTY, WHETHER MADE BY TCL, TOSHIBA  
CORPORATION, THEIR AFFILIATES, ADRs AND ASPs AND WHETHER  
MADE ORALLY OR IN WRITING (INCLUDING ANY STATEMENT IN  
ANY BROCHURE, PRESS RELEASE, ANNOUNCEMENT,  
Critical Applications  
The Television you have purchased is not designed for any “critical  
applications.” “Critical applications” means life support systems, medical  
applications, connections to implanted medical devices, commercial  
transportation, nuclear facilities or systems or any other applications  
where Television failure could lead to injury to persons or loss of life or  
catastrophic property damage.  
IF THE CUSTOMER USES THE TELEVISION IN ANY CRITICAL  
APPLICATION, THE CUSTOMER - AND NOT TCL, ITS AFFILIATES, ADRs  
OR ASPs - ASSUME SOLE AND FULL RESPONSIBILITY FOR SUCH USE.  
TCL RESERVES THE RIGHT TO REFUSE TO SERVICE ANY TELEVISION  
USED IN A CRITICAL APPLICATION. TCL, ITS AFFILIATES, ADRs AND  
ASPs HEREBY DISCLAIM ANY AND ALL LIABILITY, DAMAGES AND  
CONSEQUENCES ARISING OUT OF THE SERVICE OR REFUSAL TO  
SERVICE SUCH TELEVISION AND FURTHER DISCLAIM ANY AND ALL  
LIABILITY, CONSEQUENCES AND DAMAGES THAT MAY ARISE OR  
RESULT FROM THE USE OF THE TELEVISION IN ANY CRITICAL  
APPLICATIONS.  
ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.).  
YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE  
INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR  
MANUALS. IF YOU FAIL TO DO SO, THIS TELEVISION MAY NOT  
FUNCTION PROPERLY AND YOU MAY SUFFER DAMAGE. THIS  
WARRANTY WILL NOT COVER ANY SERVICE THAT IS REQUIRED, IN  
PART OR IN WHOLE, AS A RESULT OF ANY FAILURE TO FOLLOW THE  
SET-UP AND USAGE INSTRUCTIONS. THIS WARRANTY DOES NOT  
APPLY AND SHALL BE VOID AND UNENFORCEABLE IF THE  
TELEVISION IS OPENED, SERVICED, OR REPAIRED BY PERSONS  
OTHER THAN THOSE AUTHORIZED BY TCL TO SERVICE OR REPAIR  
THE TELEVISION.  
General Provisions  
If and to the extent that any provision of this limited warranty should  
generally be found to be unenforceable, the unenforceable provision shall  
be severed from the warranty and deemed not to form part of the warranty.  
The remaining provisions of this warranty shall be and remain valid and  
enforceable. If and to the extent that any provision of this limited warranty  
as it relates to any of the Related Parties is found to be invalid or  
unenforceable in respect of that party (the “Excluded Party”), the  
Excluded Party shall be deemed to be severed or excluded from the  
provision, and the provision shall remain valid, enforceable and  
applicable in respect of the other or remaining Related Parties.  
IF THE TELEVISION FAILS TO WORK AS WARRANTED ABOVE, YOUR  
SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT  
OF THE DEFECTIVE PART. IN NO EVENT WILL TCL, TOSHIBA  
CORPORATION, THEIR AFFILIATES, ADRs OR ASPs (THE “RELATED  
PARTIES”) BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY  
DAMAGES, MONEY, REIMBURSEMENT, COSTS OR EXPENSES. THIS  
LIMITATION APPLIES TO DAMAGES, MONEY, REIMBURSEMENT,  
COSTS OR EXPENSES OF ANY KIND WHATSOEVER INCLUDING ANY  
DIRECT OR INDIRECT DAMAGES, DAMAGE TO PROPERTY OR  
PERSON, LOST PROFITS, LOST SAVINGS, INCONVENIENCE OR  
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL  
DAMAGES, WHETHER FOR BREACH OF WARRANTY, BREACH OF  
CONTRACT, TORT (INCLUDING NEGLIGENCE), UNDER A STATUTE OR  
UNDER ANY OTHER LAW OR FORM OR ACTION, OR WHETHER  
ARISING OUT OF THE USE OF OR INABILITY TO USE THE TELEVISION,  
EVEN IF ANY OF THE RELATED PARTIES HAS BEEN ADVISED OF THE  
POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER  
PARTY.  
To the extent permitted by law, this limited warranty shall be governed and  
construed in accordance with the laws of Ontario.  
If there is any inconsistency between this limited warranty, on the one  
hand, and any statement in the packaging of the Television or in any other  
document enclosed with, or used in the context of the promotion or sale  
of, the Television, on the other hand, the provisions of this limited warranty  
shall prevail.  
How to Obtain Warranty Services  
If, after following all of the operating instructions in this manual and  
checking the “Troubleshooting” section, you find that service is needed:  
No person, agent, distributor, dealer or company is authorized to change,  
modify or extend the terms of these warranties in any manner whatsoever.  
(1) To find the nearest ASP, visit TCL’s web site at www.toshiba.ca, or  
call toll free 1-800-268-3404  
(2) Present your bill of sale or other proof of purchase to the ASP.  
Arbitration and Dispute Resolution  
To the extent not precluded by law, any claim, dispute, controversy or  
disagreement (whether for breach of warranty, breach of contract, tort  
(including negligence), under a statute or under any other law or form of  
action) against any of the Related Parties arising out of, or otherwise  
relating to: (i) this warranty; (ii) the Television; (iii) any oral or written  
representations, statements, brochures, press releases, advertising,  
announcement, point of sale display, or promotional material relating to  
the Television; (iv) the relationships that result from this warranty, (the  
foregoing claims, disputes controversies and disagreements are  
collectively referred to as the “Dispute”), shall be referred to and resolved  
by final and binding arbitration (to the exclusion of the courts). To the  
extent not precluded by law, you agree to waive any right that you may  
have to commence or participate in any representative or class  
proceeding against the Related Parties relating to any Dispute. If and  
where applicable and to the extent not precluded by law, you further  
For additional information, visit TCL’s website at www.toshiba.ca  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 10: Appendix  
A copy of the GPL source code in this product may be obtained by  
contacting Toshiba Consumer Solutions at (800)631-3811. There will be  
a charge to cover the costs of providing the source code.  
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”  
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE  
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR  
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL  
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF  
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR  
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND  
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT  
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)  
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN  
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product  
includes cryptographic software written by Eric Young  
A copy of the LGPL source code in this product may be obtained by  
contacting Toshiba Consumer Solutions at (800)631-3811. There will be  
a charge to cover the costs of providing the source code.  
USB Protocol Copyright © 2005 The NetBSD Foundation, Inc. All rights  
reserved.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are met:  
(1) Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
(2) Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
(3) Neither the name of The NetBSD Foundation nor the names of its  
contributors may be used to endorse or promote products derived  
from this software without specified prior written permission.  
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC.  
AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED  
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL  
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY  
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE.  
([email protected]). This product includes software written by Tim  
Hudson ([email protected]).  
Copyright © 1995-1998 Eric Young ([email protected]). All Rights  
reserved. This package is an SSL implementation written by Eric Young  
([email protected]). The implementation was written so as to conform  
with Netscapes SSL. This library is free for commercial and non-  
commercial use so long as the following conditions are adhered to. The  
following conditions apply to all code found in this distribution, be it the  
RC4, RSA, Ihash, DES, etc., code; not just the SSL code. The SSL  
documentation included with this distribution is covered by the same  
copyright terms except that the holder is Tim Hudson ([email protected]).  
Copyright remains Eric Young’s, and as such any Copyright notices in  
the code are not to be removed. If this package is used in a product, Eric  
Young should be given attribution as the author of the parts of the library  
used. This can be in the form of a textual message at program startup  
or in documentation (online or textual) provided with the package.  
Redistribution and use in source and binary forms, with or without  
modification, are permitted provided that the following conditions are met:  
(1) Redistributions of source code must retain the copyright notice, this  
list of conditions and the following disclaimer.  
(2) Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
(3) All advertising materials mentioning features or use of this software  
must display the following acknowledgement: “This product includes  
cryptographic software written by Eric Young ([email protected]).”  
The word ‘cryptographic’ can be left out if the routines from the library  
being used are not cryptographic related.  
This product includes software developed by the OpenSSL Project for use  
in the OpenSSL Toolkit (http://www.openssl.org).  
This product includes cryptographic software written by Eric Young  
OpenSSL 0.9.7d Copyright © 1998-2000 the OpenSSL Project. All Rights  
reserved. Redistribution and use in source and binary forms, with or  
without modification, are permitted provided that the following conditions  
are met:  
(4) If you include any Windows specific code (or derivative thereof) from  
the apps directory (application code) you must include an  
(1) Redistributions of source code must retain the above copyright  
notice, this list of conditions and the following disclaimer.  
(2) Redistributions in binary form must reproduce the above copyright  
notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
(3) All advertising materials mentioning features or use of this software  
must display the following acknowledgement: This product includes  
software developed by the OpenSSL Project for use in the OpenSSL  
Toolkit (http://openssl.org).  
(4) The names “OpenSSL Toolkit” and “Open SSL Project” must not be  
used to endorse or promote products derived from this software  
without prior written permission. For written permission, please  
contact [email protected].  
(5) Products derived from this software may not be called “OpenSSL” nor  
may “Open SSL” appear in their names without prior written  
permission of the OpenSSL Project.  
(6) Redistributions of any form whatsoever must retain the following  
acknowledgement: “This product includes software developed by the  
OpenSSL Project for use in the OpenSSL Toolkit (http://  
www.openssl.org).”  
acknowledgement: “This product includes software written by Tim  
Hudson ([email protected]).”  
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY  
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED  
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO  
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR  
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR  
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,  
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF  
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER  
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE  
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGE. The license and distribution terms for any publicly available  
version or derivative of this code cannot be changed, i.e. this code cannot  
simply be copied and put under another distribution license (including the  
GNU Public License).  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
POWER button ........................ 13, 24  
A
F
Antenna cable ................................ 15  
Antenna input configuration ............ 32  
Audio quality adjustments ............... 48  
Audio system connection................ 21  
Auto aspect.................................... 44  
Auto power off................................ 56  
Features, TV ..................................11  
Front of the TV ...............................13  
R
RECALL button...............................56  
Remote control  
G
Battery installation....................23  
Device code table.....................28  
Effective range.........................23  
Functional key chart .................26  
Learning about the buttons .......24  
Programming ...........................27  
Game Mode feature........................59  
H
HDMI audio mode...........................35  
HDMI cable ....................................15  
HDMIconnection..........................20  
B
Back of the TV................................ 14  
Base closed captions...................... 46  
Blocking channels .......................... 52  
Reset Factory Defaults....................37  
I
S
INFO button....................................56  
INPUT button..................................38  
Installation, care, and service............3  
Installation, setup............................12  
Integrated digital tuning...................11  
Safety...............................................2  
SAP sound .....................................48  
Satellite receiver connection............18  
Scroll settings .................................43  
Selecting Menu Language...............32  
Service .............................................4  
Side panel control ...........................13  
Sleep timer .....................................55  
Specifications .................................72  
StableSound®................................... 49  
Stereo sound ..................................48  
SurfLock........................................ 41  
S-video cable..................................15  
System status .................................36  
C
Cable box connection ..................... 17  
CableClear® ..................................... 58  
Camcorder connection.................... 19  
CH Bb buttons ........................24, 41  
CH RTN button.........................24, 41  
Channel Browser Setup.................. 39  
Channel Browser........................... 39  
Channel labeling ............................ 34  
Channel Number buttons..........24, 41  
J
JPEG .............................................68  
L
Labeling video input........................38  
Language selection.........................32  
Last mode memory feature .............56  
LED indications.........................13, 71  
Channel programming  
Automatic programming........... 33  
Manually adding and deleting... 33  
LOCKS menu  
Cinema mode................................. 44  
Closed captions.............................. 46  
Color temperature .......................... 58  
ColorStream®................................... 18  
Component video ........................... 18  
Component video cables ................ 15  
Connecting cables.......................... 15  
Channels, blocking...................52  
Enable rating blocking..............51  
New PIN code..........................50  
Panel lock................................54  
Unlocking programs  
temporarily.................53  
Video inputs, locking ................53  
T
TheaterWide® picture size ...............42  
Troubleshooting..............................69  
TV status information ......................56  
V
Locks menu....................................50  
V-Chip blocking (Locks menu).........50  
VCR connection................. 16, 17, 18  
Video cables...................................15  
Video input label .............................38  
Video input lock ..............................53  
D
M
Digital Audio Out ............................ 21  
Digital audio selector ...................... 47  
Digital CC Settings ......................... 46  
Digital signal meter......................... 36  
Dolby Digital................................... 21  
MP3 ...............................................67  
MPEG noise reduction....................59  
MTS feature ...................................48  
MUTE button..................................47  
W
Warranty  
O
Dolby Digital Dynamic Range  
Control........................................ 49  
Canada....................................74  
U.S..........................................73  
Optical audio cable .........................15  
Optical audio output format .............49  
DVD  
DVD aspect ratio ..................... 63  
Fast forward ............................ 63  
Fast reverse ............................ 63  
Frame by frame....................... 64  
MP3/JPEG CD operation ......... 66  
Playback ................................. 61  
WOW:SRS 3D ................................60  
WOW:SRS Focus ...........................60  
WOW:SRS TruBass........................60  
P
PC Audio........................................55  
PC connection................................22  
PC settings.....................................54  
Picture adjustment..........................45  
Picture mode..................................45  
Picture quality.................................45  
Picture scroll...................................43  
Picture size selection ......................42  
DVD player connection................... 18  
DVI connection............................... 20  
DynaLight...................................... 45  
Dynamic contrast............................ 57  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.  
NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.  
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400  
SERVICE CENTERS:  
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400  
MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766  
VANCOUVER: 13551 COMMERCE PARKWAY, SUITE 110, RICHMOND, B.C., V6V 2L1, CANADA – TEL: (604) 303-2500  
MANUFACTURED BY  
CableClear, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.  
Channel Browser, SurfLock, DynaLight, and LCDVD logo are trademarks of Toshiba America Consumer Products, L.L.C.  
REGZA is a trademark of Toshiba Corporation.  
PRINTED IN USA  
(07-05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Tiffen Camera Accessories PILOT AA User Manual
Timex Heart Rate Monitor W270 EU 103 095001 User Manual
Toro Sprinkler TR50 User Manual
Toshiba Telephone CT User Manual
Toshiba TV DVD Combo MD14F12 User Manual
Tricity Bendix Clothes Dryer TM 551 User Manual
Uniden Cordless Telephone D3580 User Manual
Vector Video Games VEC401 User Manual
Vertical Communications Telephone 7714s User Manual
Vizio Car Video System E320i A2 User Manual