Battery installation and Make, answer and end a call Outgoing announcement
charging
The telephone is preset with a greeting that
answers calls with “Hello, please leave a
message after the tone.” You can use this
preset announcement, or replace it with
your own.
Make a call
Install the battery as shown below. After
installing the battery, you might be able
to make and receive short calls. For best
performance, charge the handset battery for
at least 16 hours before use.
1. Press
/FLASH or
.
2. Dial the number.
-OR-
1. Dial the number.
Quick start guide
for models CS6128-31/CS6129/
CS6129-2/CS6129-3/CS6129-4/
CS6129-31/CS6129-32/CS6129-41/
CS6129-52/CS6129-54
To record your own announcement:
2. Press
/FLASH or
.
1. Press ANNC while the telephone is not
in use and the system will announce
“Announcement. Press PLAY or press
RECORD.”
2. Press RECORD and the system
announces, “Record after the tone. Press
STOP when you are done.”
1
2
Plug the battery securely
into the plug inside
the handset battery
compartment, matching
the color-coded label.
If the battery
compartment cover is on
the handset, press the
indentation and slide the
cover to remove.
Install the telephone base and
charger(s)
Install the telephone base and charger(s) as
shown below.
3. After the tone, speak towards the
microphone at the bottom front of
the telephone base from about nine
inches away.
Answer a call
Telephone
• Press
/FLASH,
or any of the dialing
wall jack
Charger
adapter
(small)
Telephone base
power adapter
(large)
keys (0-9, #, ).
*
4. Press /PLAY/STOP when finished.
DSL filter (not
included) required
if you have DSL
high-speed
5. The answering system will automatically
play the newly recorded announcement.
Press /PLAY/STOP to stop the playback
at anytime.
End a call
• Press OFF/CLEAR or put the handset in
the telephone base or charger.
Internet service
4
3
Place the battery with
the label THIS SIDE
UP facing up and the
wires inside the battery
compartment.
Align the cover flat
against the battery
compartment, then slide
it upwards until it clicks
into place.
Electrical outlet
Telephone line cord
To play messages:
not controlled
Activate the answering system
by a wall switch
• Press /PLAY/STOP to play messages
The answering system must be turned on
to answer and record messages. Press
ANS ON/OFF to turn the answering system
on or off. When the answering system is
turned on, it will announce “Calls will be
answered,” and the ANS ON/OFF light will be
on. When the answering system is turned off,
it will announce “Calls will not be answered,”
and the ANS ON/OFF light will be off.
and stop playback.
• Press X/DELETE while a message is
playing to delete it.
• Press /SKIP to skip to the next
message.
• Press /REPEAT to repeat the current
message.
• Press VOL / to raise or lower playback
Charger
volume.
5
Telephone base
CHARGE light
Charge the handset by
placing it in the telephone
base or charger. The
CHARGE light will be
on when the handset is
charging.
IMPORTANT!
If your product is not working properly:
• Refer to the Troubleshooting section of
the user’s manual.
NOTES:
1. Use only the power adapter(s) and
battery(ies) supplied with your VTech
telephone.
•
com or call 1 (800) 595-9511. In Canada,
1 (800) 267-7377.
2. For complete feature instructions,
please refer to your user’s manual.
96-006860-030-100
Download from Www.Somanuals.com. All Manuals Search And Download.
|