|
Toshiba Personal Computer
Satellite M500/M505/M507
Maintenance Manual
TOSHIBA CORPORATION
File Number
[CONFIDENTIAL]
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This maintenance manual describes how to perform hardware service maintenance for the
Toshiba Personal Computer Satellite M500/M505/M507.
The procedures described in this manual are intended to help service technicians isolate
faulty Field Replaceable Units (FRUs) and replace them in the field.
SAFETY PRECAUTIONS
Four types of messages are used in this manual to bring important information to your
attention. Each of these messages will be italicized and identified as shown below.
DANGER: “Danger” indicates the existence of a hazard that could result in death or
serious bodily injury, if the safety instruction is not observed.
WARNING: “Warning” indicates the existence of a hazard that could result in bodily
injury, if the safety instruction is not observed.
CAUTION: “Caution” indicates the existence of a hazard that could result in property
damage, if the safety instruction is not observed.
NOTE: “Note” contains general information that relates to your safe maintenance
service.
Improper repair of the computer may result in safety hazards. Toshiba requires service
technicians and authorized dealers or service providers to ensure the following safety
precautions are adhered to strictly.
Be sure to fasten screws securely with the right screwdriver. If a screw is not fully
fastened, it could come loose, creating a danger of a short circuit, which could cause
overheating, smoke or fire.
If you replace the battery pack or RTC battery, be sure to use only the same model
battery or an equivalent battery recommended by Toshiba. Installation of the wrong
battery can cause the battery to explode.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
The manual is divided into the following parts:
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Hardware Overview describes the Satellite M500/M505/M507 system
unit and each FRU.
Troubleshooting Procedures explains how to diagnose and resolve
FRU problems.
Test and Diagnostics describes how to perform test and diagnostic
operations for maintenance service.
Replacement Procedures describes the removal and replacement of the
FRUs.
Appendices The appendices describe the following:
Handling the LCD module
Board layout
Pin assignments
Keyboard scan/character codes
Key layout
BIOS rewrite procedures
EC/KBC rewrite procedures
iv
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
This manual uses the following formats to describe, identify, and highlight terms and
operating procedures.
Acronyms
On the first appearance and whenever necessary for clarification acronyms are enclosed in
parentheses following their definition. For example:
Read Only Memory (ROM)
Keys
Keys are used in the text to describe many operations. The key top symbol as it appears on
the keyboard is printed in boldface type.
Key operation
Some operations require you to simultaneously use two or more keys. We identify such
operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause
(Break) means you must hold down Ctrl and at the same time press Pause (Break). If
three keys are used, hold down the first two and at the same time press the third.
User input
Text that you are instructed to type in is shown in the boldface type below:
DISKCOPY A: B:
The display
Text generated by the computer that appears on its display is presented in the type face
below:
Format complete
System transferred
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 Hardware Overview
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
Features.................................................................... 1-Error! Bookmark not defined.
System Unit Block Diagram.................................... 1-Error! Bookmark not defined.
HDD/SSD ................................................................ 1-Error! Bookmark not defined.
DVD Super Multi Drive........................................... 1-Error! Bookmark not defined.
Keyboard.................................................................. 1-Error! Bookmark not defined.
TFT Color Display................................................... 1-Error! Bookmark not defined.
Power Supply........................................................... 1-Error! Bookmark not defined.
Batteries ................................................................... 1-Error! Bookmark not defined.
AC Adaptor.............................................................. 1-Error! Bookmark not defined.
Chapter 2 Troubleshooting Procedures
Troubleshooting Procedures ........................................... 2-Error! Bookmark not defined.
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
Troubleshooting....................................................... 2-Error! Bookmark not defined.
Troubleshooting Flowchart...................................... 2-Error! Bookmark not defined.
Power Supply Troubleshooting................................ 2-Error! Bookmark not defined.
Main Board Troubleshooting................................... 2-Error! Bookmark not defined.
HDD/SSD Troubleshooting..................................... 2-Error! Bookmark not defined.
Keyboard and Touch pad Troubleshooting.............. 2-Error! Bookmark not defined.
Display Troubleshooting.......................................... 2-Error! Bookmark not defined.
Optical Drive Troubleshooting ................................ 2-Error! Bookmark not defined.
Modem Troubleshooting.......................................... 2-Error! Bookmark not defined.
2.10 LAN Troubleshooting.............................................. 2-Error! Bookmark not defined.
2.11 Wireless LAN Troubleshooting............................... 2-Error! Bookmark not defined.
2.12 Sound Troubleshooting............................................ 2-Error! Bookmark not defined.
2.13 Card Reader Slot Troubleshooting .......................... 2-Error! Bookmark not defined.
2.14 PCI Express Card Slot Troubleshooting.................. 2-Error! Bookmark not defined.
2.15 Fingerprint Board(BTO) Troubleshooting............... 2-Error! Bookmark not defined.
vi
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.16 Bluetooth(BTO) Troubleshooting............................ 2-Error! Bookmark not defined.
2.17 3G(BTO) Troubleshooting....................................... 2-Error! Bookmark not defined.
2.18 Camera(BTO) Troubleshooting............................... 2-Error! Bookmark not defined.
Chapter 3 Tests and Diagnostics
Tests and Diagnostics .......................................................... 3-Error! Bookmark not defined.
3.1
Model,BIOS and CPU Test...................................... 3-Error! Bookmark not defined.
3.1.1 CPU Test.................................................................. 3-Error! Bookmark not defined.
3.1.2 Memory Test............................................................ 3-Error! Bookmark not defined.
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Check MAC Test ..................................................... 3-Error! Bookmark not defined.
ACIN Test................................................................ 3-Error! Bookmark not defined.
Temperature Test ..................................................... 3-Error! Bookmark not defined.
USB TEST ............................................................... 3-Error! Bookmark not defined.
USBCCD Test.......................................................... 3-Error! Bookmark not defined.
PAD Test.................................................................. 3-Error! Bookmark not defined.
LCDRGB Test ......................................................... 3-Error! Bookmark not defined.
VGA Test................................................................. 3-Error! Bookmark not defined.
3.10 Audio Test................................................................ 3-Error! Bookmark not defined.
3.11 Keyboard Test.......................................................... 3-Error! Bookmark not defined.
3.12 Function TEST......................................................... 3-Error! Bookmark not defined.
3.13 LEDALL Test .......................................................... 3-Error! Bookmark not defined.
3.14 STORE Test [CD/DVD-ROM TEST]..................... 3-Error! Bookmark not defined.
3.15 LID Switch Test....................................................... 3-Error! Bookmark not defined.
3.16 MS CARD Test........................................................ 3-Error! Bookmark not defined.
3.17 SD CARD Test ........................................................ 3-Error! Bookmark not defined.
3.18 HDD Test................................................................. 3-Error! Bookmark not defined.
3.19 BATTERY Test ....................................................... 3-Error! Bookmark not defined.
3.20 Touch LED Test....................................................... 3-Error! Bookmark not defined.
3.21 HDD 3D Protection.................................................. 3-Error! Bookmark not defined.
3.22 Speaker Test............................................................. 3-Error! Bookmark not defined.
3.23 Auto Run.................................................................. 3-Error! Bookmark not defined.
3.0
Appendix:................................................................. 3-Error! Bookmark not defined.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Replacement Procedures
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
General...................................................................Error! Bookmark not defined.
Battery pack ...........................................................Error! Bookmark not defined.
Express card...........................................................Error! Bookmark not defined.
HDD module..........................................................Error! Bookmark not defined.
Memory module.....................................................Error! Bookmark not defined.
Wireless LAN card ................................................Error! Bookmark not defined.
Keyboard................................................................Error! Bookmark not defined.
Top cover ...............................................................Error! Bookmark not defined.
Bluetooth................................................................Error! Bookmark not defined.
4.10 Power Button Board...............................................Error! Bookmark not defined.
4.11 Fingerprint module.................................................Error! Bookmark not defined.
4.12 Touchpad on-off board ..........................................Error! Bookmark not defined.
4.13 Main PCB...............................................................Error! Bookmark not defined.
4.14 LAN Board.............................................................Error! Bookmark not defined.
4.15 D/C IN Cable .........................................................Error! Bookmark not defined.
4.16 Speaker...................................................................Error! Bookmark not defined.
4.17 Remove LCD Module............................................Error! Bookmark not defined.
4.18 CPU Heat sink/CPU...............................................Error! Bookmark not defined.
4.19 VGA Card ..............................................................Error! Bookmark not defined.
4.20 FAN Error! Bookmark not defined.
4.21 LCD unit/Camera...................................................Error! Bookmark not defined.
viii
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix A Handling the LCD Module ........................................................................... A-1
Appendix B Board Layout ................................................................................................ B-1
Appendix C Pin Assignments............................................................................................ C-1
Appendix D Keyboard Scan/Character Codes .................................................................. D-1
Appendix E Key Layout.....................................................................................................E-1
Appendix F BIOS rewrite Procedures ...............................................................................F-1
Appendix G EC/KBC rewrite Procedures......................................................................... G-1
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Chapter 1
Hardware Overview
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Chapter 1
Contents
Features...................................................................................................................... 1-4
System Unit Block Diagram.................................................................................... 1-10
Power Supply........................................................................................................... 1-21
RTC battery........................................................................................ 1-23
1-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Figures
Figure 1-1 The front and left view of the computer ............................................................ 1-8
Figure 1-2 System unit configuration .................................................................................. 1-9
Figure 1-3 System unit block diagram............................................................................... 1-10
Figure 1-4 2.5-inch HDD................................................................................................... 1-15
Figure 1-5 SSD .................................................................................................................. 1-16
Figure 1-6 DVD Super Multi Drive................................................................................... 1-17
Figure 1-7 Keyboard.......................................................................................................... 1-19
Tables
Table 1-1 2.5-inch HDD specifications (1/1) ..................................................................... 1-15
Table 1-2 1.8-inch SSD specifications (1/1)....................................................................... 1-16
Table 1-3 DVD Super Multi drive specifications (1/1)..................................................... 1-18
Table 1-4 LCD module specifications (1/1) ...................................................................... 1-20
Table 1-5 Power supply output rating................................................................................ 1-21
Table 1-6 Battery specifications ........................................................................................ 1-22
Table 1-7 Time required for charges ................................................................................. 1-23
Table 1-8 RTC battery charging/data preservation time ................................................... 1-24
Table 1-9 AC adaptor specifications for integrated graphic model................................... 1-25
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Comment [z1]:
Please add below item.
1.eSATA/USB combo port
2.webcam (BTO)
1.1 Features
3.SIM card Slot
The Toshiba Satellite M500/M505/M507 Personal Computer uses extensive Large Scale
Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology
extensively to provide compact size, minimum weight, low power usage and high reliability.
This computer incorporates the following features.
4.HDMI
5.Headphone/s/PDIF jack
6. Microphone jack
7.Bluetooth (BTO)
8. Fingerprint (BTO)
9. IEEE 1394 port
Refer to the Parts List for the configuration of each model and the available options.
Microprocessor
The Satellite M500/M505/M507 computer is equipped with an Intel® Core2 Duo
Processor, Intel® Pentium® Dual-Core mobile processor or Intel® Celeron Processor.
These processors incorporate a math co-processor with L2 cache memory.
Chipset
The Satellite M500/M505/M507 is equipped with Mobile Intel 4 Series Express Chipset
Family and Intel ICH9-M.
Comment [z2]:
Please add AMD M92XT
information.
GPU (Graphics Processing Unit)
(1) Integrated graphic model: Intel integrated graphics (Mobile Intel 4 Series Express
Chipset Family)
(2) Discrete graphic model: AMD M92XT
Comment [z3]:
Please add the below sentence
“It can incorporate up to 8GB of
main memory.”
Memory
The computer comes with two DDR2 SO-DIMM slots. Two memory modules of 1GB
(1,024MB), 2GB (2,048MB) or 4GB (4,096MB) can be installed, and it can incorporate
up to 8GB of main memory.
Comment [z4]:
Please add SSD information.
HDD/SSD
(1) HDD: The computer has a 2.5-inch SATA HDD. The following capacities are
available:
160/250/320/400/500 GB
(2) SSD (BTO): The computer has a SSD port with SATA interface supporting
TOSHIBA module type SSD.
Comment [z5]:
1. Please add more detail on ODD.
Ex : 12.7mm heigh DVD superMulti
driver support +- R double layer
2. Please add slot in ODD
information.
Optical Drive
The computer accommodates a fixed 12.7mm ODD with one of following types:
1-4
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Tray Type DVD Super Multi +-R Double Layer drive
Tray Type DVD Super Multi +-R Double Layer with Label Flash™ drive
Slot Loading Type DVD Super Multi +-R Double Layer drive
Slot Loading Type DVD Super Multi +-R Double Layer with Label Flash™ drive
Display
The PC comes with 14.0W WXGA (1366*768) CSV LED backlight.
Keyboard
A4 size 86 key (US) and 87 key (UK) keyboard provides a numeric keypad overlay for
fast numeric data entry or for cursor and page control. The keyboard also includes two
keys that have special functions in Microsoft® Windows® Vista.
Comment [z6]:
Modify sentence to
Pointing Device
“The touch pad and control buttons
enable control of the on-screen
pointer and scrolling of windows.”
The touch pad and control buttons enable control of the on-screen pointer and scrolling of
windows.
Comment [z7]:
Please add below sentence.
“The capacity can be either 6 cell or
12 cell depending on the model of
computer.”
Batteries
The computer has two batteries: a rechargeable Lithium-Ion main battery pack and RTC
battery (that backs up the Real Time Clock and CMOS memory). The capacity of the
main battery pack can be either 6-cell or 12-cell depending on the model of computer.
Universal Serial Bus (USB2.0)
Three USB ports are provided. The ports comply with the USB2.0 standard, which
enables data transfer speeds 40 times faster than USB1.1 standard. USB1.1 is also
supported.
External monitor (RGB) port
The port enables connection of an external monitor, which is recognized automatically by
Video Electronics Standards Association (VESA) Display Data Channel (DDC)
compatible functions.
Comment [z8]:
Please add type of Express Card
( 134 and 154 module)
Express Card slot
An Express Card slot is provided, and accommodates an Express Card. Support the
standard 34mm wide module (ExpressCard / 34) and the standard 54mm wide module
(ExpressCard / 54).
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Media Card slot
The Media Card Slot can accommodate all types of media (SD/Mini SD (card adapter is
needed)/Micro SD (card adapter is needed)/SDHC memory card/MMC/Memory
stick/Memory stick PRO/memory stick pro duo (card adapter is needed)/XD) with
various capacities. Media cards let you easily transfer data from devices, such as digital
cameras and Personal Digital Assistants, which use Media Card flash-memory.
Comment [z9]:
Please input all types (SD/Mini
SD/Micro SD/SDHC memory
card/MMC/Memory stick/Memory
stick PRO/memory stick pro duo/XD)
Comment [z10]:
Please add Harman/kardon
(Depending on model) information.
Sound system
The sound system is equipped with the following features:
Azalia Link (Intel High Definition Audio I/F) built in the Intel ICH9-M + Realtek
ALC269
Amplifier: Realtek ALC269 built-in
Speaker: Non-brand or Harman/Kardon speaker (depending on model)
Internal modem
The computer contains an MDC, enabling data and fax communication. The transfer rates
are 56 Kbps for data reception. The actual speed depends on the line quality. The RJ11
modem jack is used to accommodate a telephone line.
Internal LAN (BTO)
The computer is equipped with LAN circuits that support Ethernet LAN (10/100 Mbps or
10/100/1000 Mbps). It also supports Wakeup on LAN (WOL), Magic Packet and LED.
Wireless LAN
The computer is equipped with PCI-E MiniCard type wireless LAN board that supports
802.11 a/b/g in the PCI-E MiniCard slot. This function can be switched on and off by a
switch on the computer.
eSATA / USB Combo port
The computer is equipped with an eSATA and USB combo port that supports connection
of an external eSATA or USB device.
The USB port complies with the USB 2.0 standard, which enables data transfer speeds 40
times faster than USB1.1 standard. USB1.1 is also supported, and also supports Sleep and
Charge function that can supply bus power to USB when the PC is sleeping.
1-6
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Webcam Module (BTO)
The computer is equipped with a webcam module which is embedded to transfer video
data – to take still image and offer video stream for end user to preview/record motion
image through USB 2.0 interface.
SIM card slot
A user accessible SIM card slot is provided behind battery.
HDMI port
A HDMI port is provided which complies with the HDMI 1.3 standard.
Headphone / S/PDIF jack
The computer is equipped with a headphone jack which is shared with S/PDIF jack.
Microphone Jack
The computer is equipped with a microphone jack.
Bluetooth Module (BTO)
The computer is equipped with a Bluetooth module with antenna through USB interface.
Fingerprint (BTO)
The fingerprint sensor can support on-chip fingerprint matching functionality and
security engine.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Comment [z11]:
Please use the more detail photo to
show computer and system unit
configuration.
The front of the computer is shown in figure 1-1.
Figure 1-1 The front and left view of the computer
1-8
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
The system unit configuration is shown in figure 1-2.
Touch
PAD
M1TP_CON1
LAN/RJ11
MLCON301
USB*2
Touch PAD
Board
MLCON103
M1TP_J1
BTO
Fingerprint
T/P
ON/OFF
Board
LAN
Board
MLCON101
Power
Button
Board
HP/
SPDIF
MDC
MIC
CON6501
BTO
CON6503
CON4802
CON4202
CON6701
CON6002
CON4201
CON7701
CON4804
ODD
Battery
DC-IN
Keyboard
Felica
Function
Board
CON6601
CON3701
J7701
CON4801
LCD
Touch
Panel
CON6201
BTO
CON6204
BTO
CON3801
CON6106
CON6001
RGB
WWAN
USB*1
HDD
Main Board
CON5601
BTO
CON6003
BTO
CON6107
CON5001
eSATA/USB
SSD
Media
Card
CON3901
BTO
HDMI
CON5501
BTO
CON6202
BTO
Upconvert
Newcard
Camera
WLAN
CON5401
CON6203
CON5701
CON4901
CON410
1
CON2101
CON2201
CON5602
BlueToot
SIM
card
DIMM0
DIMM1
Speaker
FAN
h
Figure 1-2 System unit configuration
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Comment [z12]:
Please add BIOS ROM (Flash EEP
ROM) information.
The system unit is composed of the following major components:
Comment [z13]:
Please add core speed detail.
Processor
Intel® Core2 Duo Processor, Intel® Pentium® Dual-Core mobile processor or
Mobile Intel® Celeron Processor
Core speed:
Intel® Core2 Duo mobile processors:
3.06GHz(T9900), 2.8GHz(P9700), 2.8GHz (T9600), 2.66GHz (P8800),
2.53GHz (P8700), 2.26GHz (P7550), 2.2GHz (T6600), 2.1GHz (T6500),
2.0GHz (P7350)
Intel® Pentium® Dual-Core mobile processor:
2.1GHz(T4300), 2.0GHz(T4200), 1.9GHz (T3100), 1.8GHz(T3000)
Mobile Intel® Celeron® Processors:2.2GHz (900)
478-pin Micro FCPGA package
BIOS EEPROM
8 Mbit SPI serial flash
Supply voltage: 2.7~3.6V
Low power consumption: active read: 10mA (typical); standby: 5uA (typical).
8-lead SOIC package
Memory
Two memory slots are provided. Expansion up to 8GB is available.
Memory
–DDR2-SDRAM
–800MHz
–1.8 volt operation
–FBGA
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Memory Module
–200 pin, SO Dual In-line Memory Module (SO-DIMM)
–PC6400
–1GB (1,024MB), 2GB (2,048MB), 4GB (4,096MB)
Intel GMCH (North Bridge)
One Intel® 4 Series Express Chipset is used
Features:
–
667/800/1066 MHz FSB
–
–
–
–
Supports DDR2/DDR3
8GB maximum memory support
Internal Graphics Controller: 533MHz core render clock @1.05V core voltage
DMI: 2GB/s (1GB/s each direction), point-to-point interface to ICH
–
1329-ball 34 mm x 34 mm FCBGA package
Intel ICH9-M (South Bridge)
Comment [z14]:
This should be ICH9-M
One Intel ICH9-M is used
Features:
–
DMI (Direct Media Interface)
–
PCI Express: 6 PCI Express root ports, Supports PCI Express 1.1
–
–
PCI Bus I/F: Supports PCI Rev 2.3 Specification at 33 MHz
Integrated Serial ATA Host Controller: 6 SATA ports. Data transfer rates up to
3.0Gb/s. Integrated AHCI controller
–
–
External SATA support
Intel High Definition Audio Interface: Independent Bus Master logic for 8
general purpose streams: 4 input and 4 output
–
–
USB 2.0: 6 UHCI Host Controllers, supporting up to 12 external ports. 2 EHCI
Host Controllers, supporting up to 12 external ports
Power Management Logic: Supports ACPI 3.0b. Support for “Intel SpeedStep
Technology” processor power control and “Deeper Sleep” power state
–
–
Enhanced DMA Controller
SMBus controller: Supports SMBus 2.0 Specification
1-12
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
–
–
–
–
Real-Time Clock: 256-byte battery-backed CMOS RAM
Low Pin Count (LPC) I/F: Supports 2 Master/DMA devices
GPIO
676-ball 31mm×31mm mBGA Package
Card Reader Controller
One Ricoh R5U230 is used
Futures:
–
PCI Express I/F
–
–
SD/MMC, Memory Stick, XD Card Controller
48-pin, 6mm×6mm, QFN Package
Sound Controller
Realtek ALC269
Mono Microphone-in and stereo headphone-out shared with SPDIF.
Internal Microphone
Volume control: Digital control
Stereo w/box, 4 ohm / 1.5W. L/R = 12.7cc/10.65cc (Harman/Kardon); 13cc/11cc
(Non-brand).
EC/KBC (Embedded Controller/Keyboard Controller)
One ITE8512E chip functions as both EC and KBC.
Clock Generator
One Intel CK-505 compatible clock generator is used.
This device generates the system clocks
Modem Controller
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
One MDC is used
This controller has the following functions:
–
One RJ11 port
–
–
Digital line protection support
V.92 (V.90) 56K Modem/FAX
LAN Controller
Realtek RTL8103EL or RTL8111DL is used (depending on model)
This controller has the following functions:
–
PCIE I/F
–
Supports 10/100 Mbps or 10/100/1000 Mbps Ethernet
–
–
One RJ45 port
WOL support
–
Magic Packet support
Wireless LAN
One PCI-E MiniCard is used
Support 802.11 a/b/g/n or 802.11 a/b/g or 802.11 b/g/n
Sensor
Thermal Sensor: One MAXIM MAX6657 or compatible chip is used
1-14
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.3 HDD/SSD
Comment [z15]:
Please add SSD information.
1.3.1 2.5-inch Hard Disk Drive
The removable HDD is a random access non-volatile storage device. It has a non-removable
2.5-inch magnetic disk and mini-Winchester type magnetic heads.
The computer supports a 160GB, 250GB, 320GB, 400GB and 500GB.
The HDD is shown in figure 1-4. Specifications are listed in Table 1-1.
Figure 1-4 2.5-inch HDD
Table 1-1 2.5-inch HDD specifications (1/1)
Item
Capacity (GB)
Rotational Speed (RPM)
Height
Specifications
250 GB
160 GB
5400 rpm
9.5 mm
320 GB
5400 rpm
9.5 mm
5400 rpm
9.5 mm
312,581,808
512
488,397,168
512
625,142,448
512
User Data Sectors
Bytes / Sector
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Item
Capacity (GB)
Rotational Speed (RPM)
Height
Specifications
400 GB
5400 rpm
9.5 mm
500 GB
5400 rpm
9.5 mm
User Data Sectors
Bytes / Sector
781,422,768
512
976,773,168
512
1.3.2 SSD
The solid-state drive (SSD) is a data storage device that uses solid-state memory to store
persistent data. A SSD emulates a hard disk drive interface, thus easily replacing it in most
applications.
The computer supports a dedicated SSD port with TOSHIBA module type SSD.
The SSD is shown in figure 1-5. Specifications are listed in Table 1-2.
Figure 1-5 SSD
Table 1-2 1.8-inch SSD specifications (1/1).
Item
Specifications
64 GB
Capacity (GB)
Number of data heads
16
Number of user data cylinders
User Addressable Sectors in LBA Mode
Bytes / Sector
16,383
125,045,424
512
1-16
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
Comment [z16]:
Please add DVD drive photo.
1.4 DVD Super Multi Drive
This drive is a combination of DVD-ROM and DVD±R/±RW/-RAM Drive. It is full-size and
runs either 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. It reads
DVDs at maximum 8x speed and CDs at maximum 24x speed. It also writes CD-R at
maximum 24x speed, CD-RW at maximum 24x speed, DVD±R at maximum 8x speed,
DVD-RW at maximum 6x speed, DVD+RW at maximum 8x speed, DVD±R DL at
maximum 6x speed and DVD-RAM at maximum 3-5x speed.
The DVD is shown in figure 1-6.
Figure 1-6 DVD Super Multi drive
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
The specifications are listed in Table 1-3.
Table 1-3 DVD Super Multi drive specifications (1/1)
Specifications
DVD-ROM mode
Item
CD-ROM mode
SATA Interface (Mbytes/s)
Average access time (ms)
150 Mbyte/s
180ms Typ.
150ms Typ.
Data Buffer Capacity
Support Formats
2MB
CD-DA, CD-ROM
CD-ROM XA
Photo CD (Multi-session)
Video CD, CD-Extra(CD+), CD-Text
DVD-ROM
DVD-R
DVD-Video
DVD-RAM (4.7GB)
DVD+R/RW, DVD+R DL
DVD-RW(Ver. 1.1/1.2)
1-18
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.5 Keyboard
The keyboard has 86(US)/87(UK) keys that consist of character keys and control keys, and is
in conformity with JIS. The keyboard is connected to a membrane connector on the system
board and is controlled by EC.
Figure 1-7 is a view of the keyboard.
Figure 1-7 Keyboard
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.6 TFT Color Display
The TFT color display consists of 14.0-inch LCD module.
The LCD module used for the TFT color display uses a LED backlight as the light source
and can display a maximum of 262,144 colors with 1366*768 resolution.
Table 1-4 lists the specifications.
Table 1-4 LCD module specifications (1/1)
Specifications
Item
14.0" WXGA (1366*768)
CSV type
Number of Dots
1,366 (W) * 768 (H)
0.2265(H) * 0.2265(V)
309.4(H) * 173.95(V)
Dot spacing (mm)
Display range (mm)
1-20
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.7 Power Supply
The power supply provides different voltages to the system board and performs the following
functions:
1. Determines that the DC power supply (AC adapter) is connected to the computer.
2. Detects DC output and circuit malfunctions.
3. Controls the battery icon, and DC IN icon.
4. Turns the battery charging system on and off and detects a fully charged battery.
5. Turns the power supply on and off.
6. Provides more accurate detection of a low battery.
7. Calculates the remaining battery capacity.
8. Controls the transmission of the status signal of the main battery.
The power supply output rating is specified in Table 1-5.
Table 1-5 Power supply output rating
Name
Voltage (V)
Use
VID (Intel spec)
CPU
+VCORE
+VCCP
+1.5VS
+1.8V
1.05
1.5
1.8
0.9
3.3
3.3
CPU, GMCH, ICH9-M
CPU, GMCH, ICH9-M, Express Card, Mini Card
GMCH, DDR2-SDRAM
+0.9V
DDR2-SDRAM
+3VSUS
+3V
ICH9-M, Express Card, Mini Card, LAN, HDMI CEC
MDC
Thermal Sensor, Clock gen, LCD, DDR2-SDRAM, ICH9-
M, Express Card, Mini Card, EC, GMCH, Fingerprint, Card
Reader, SSD, Bluetooth
+3VS
3.3
+3VA
+5VA
3.3V
EC, SPI ROM
Function Board
ICH9-M, USB
5
5
+5VSUS
FAN, ICH9-M, Audio, ODD, HDD, LED, Touchpad,
Keyboard backlight, CCD, FeliCa, G-sensor
+5VS
5
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.8 Batteries
The computer has two types of batteries as follows:
Main battery pack
RTC battery
The battery specifications are listed in Table 1-6.
Table 1-6 Battery specifications
Battery name
Main battery(6 cell)
Main battery(12cell)
RTC battery
Material
Lithium-Ion
Lithium-Ion
Lithium
Output voltage
10.8V
Capacity
4000 mAh
9000 mAh
18 mAh
10.8V
3.0 V
1.8.1 Main Battery
The removable main battery pack is the computer’s main power source when the AC adaptor
is not attached. The main battery maintains the state of the computer when the computer
enters into resume mode.
1-22
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.8.2 Battery Charging Control
Battery charging is controlled by an embedded controller (EC). The EC controls whether the
charge is on or off and detects a full charge when the AC adaptor and battery are attached to
the computer. The system charges the battery.
Battery Charge
When the AC adaptor is attached, there are two types of charge: When the system is powered
off and when the system is powered on. Table 1-7 lists the charging time required for charges.
Table 1-7 Time required for charges
Battery type
1st battery pack (6cell,12cell)
RTC Battery
Power on (hours)
4-10 hours
Power off (hours)
4 hours max
About 24 hours
About 24 hours
NOTE: The time required when the system is powered on is affected by the amount of
power the system is consuming. Use of the fluorescent lamp and frequent disk
access diverts power and lengthens the charge time.
If any of the following occurs, the battery charge process stops.
1. The battery becomes fully charged.
2. The AC adaptor or battery is removed.
3. The battery or output voltage is abnormal.
Detection of full charge
A full charge is detected only when the battery is charging at charge. A full charge is
detected under any of the following conditions:
1. The current in the battery charging circuit drops under the predetermined limit.
2. The charging time exceeds the fixed limit.
1.8.3 RTC battery
The RTC battery provides power to keep the current date, time and other setup information
in memory while the computer is turned off. Table 1-8 lists the data preservation period of
the RTC battery.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Hardware Overview
1.9 AC Adaptor
The AC adaptor is also used to charge the battery.
Table 1-9 lists the AC adaptor specifications.
Table 1-9 AC adaptor specifications for integrated graphic model
Parameter
Specification
2-pin
3-pin
Power
65W
100V-240V
Input voltage
Input frequency
Input current
50Hz–60Hz
1.6A or less (100V-240V)
19V
Output voltage
Output current
0A to 3.42A (At constant voltage mode)
Table 1-10 AC adaptor specifications for discrete graphic model
Parameter
Specification
2-pin
3-pin
Power
75W
100V-240V
Input voltage
Input frequency
Input current
50Hz - 60Hz
1.5A or less (100V-240V)
19V
Output voltage
Output current
0A to 3.95A (At constant voltage mode)
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Chapter 2
Contents
Troubleshooting Procedures......................................................................................... 2-1
Troubleshooting......................................................................................................... 2-5
Procedure 1 Icons in the LCD Check.............................................................. 2-10
Procedure 2 Error Code Check........................................................................ 2-11
Procedure 3 Connection Check ....................................................................... 2-15
Procedure 4 Charge Check.............................................................................. 2-16
Procedure 5 Replacement Check..................................................................... 2-17
Procedure 1 Message Check............................................................................ 2-19
Procedure 3 Replacement Check..................................................................... 2-22
HDD/SSD Troubleshooting..................................................................................... 2-23
Procedure 1 Message Check............................................................................ 2-23
Procedure 2 Partition Check............................................................................ 2-24
Procedure 3 Format Check.............................................................................. 2-25
Procedure 1 External Monitor Check.............................................................. 2-31
Procedure 4 Replacement Check..................................................................... 2-32
2-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.10 LAN Troubleshooting.............................................................................................. 2-37
2.11 Wireless LAN Troubleshooting............................................................................... 2-38
Procedure 3 Replacement Check..................................................................... 2-40
2.12 Sound Troubleshooting............................................................................................ 2-41
Procedure 2 Connector Check......................................................................... 2-42
2.13 Card Reader Slot Troubleshooting........................................................................... 2-44
2.14 PCI Express Card Slot Troubleshooting.................................................................. 2-45
2.15 Fingerprint Board(BTO) Troubleshooting............................................................... 2-47
2.16 Bluetooth(BTO) Troubleshooting............................................................................ 2-49
2.17 3G(BTO) Troubleshooting....................................................................................... 2-51
2.18 Camera(BTO) Troubleshooting............................................................................... 2-53
Comment [z1]:
1.Please add SSD troubleshooting,
camera (BTO) troubleshooting and
thermal module troubleshooting.
2.add “ BTO” behind 2.15 fingerprint
board troubleshooting , Bluetooth
troubleshooting and 3G troubleshooting.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Figures
Figure 2-1 Troubleshooting flowchart (1/2) ......................................................................... 2-7
Tables
Table 2-1 Battery icon ........................................................................................................ 2-10
Table 2-2 DC IN icon ......................................................................................................... 2-10
Table 2-3 Error code........................................................................................................... 2-11
Table 2-4 HDD/SSD error code and status......................................................................... 2-26
2-4
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.1 Troubleshooting
Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is
causing the computer to malfunction. The FRUs covered are:
Comment [z2]:
1.Please add SSD ,camera (BTO) and
thermal module
2.Add “BTO” behind #13 Fingerprint
board, #14 Bluetooth and #15 3G
1
2
3
Power Supply
Main Board
HDD/SSD
6
7
8
Optical Drive
Modem
11 Card reader
12 PCI Express Slot
LAN
13 FINGERPRINT BOARD
(BTO)
4
5
Keyboard/Touch pad
Display
9
Wireless LAN
14 Bluetooth (BTO)
15 3G (BTO)
10 Sound component
16 Camera (BTO)
The Diagnostics Disk operations are described in Chapter 3. Detailed Replacement
Procedures are given in Chapter 4, Replacement Procedures.
The following tools are necessary for implementing the troubleshooting procedures:
The following tools are necessary for implementing the Diagnostics procedures:
For tools required for executing the Test Program, refer to the Chapter 3. For tools required
for disassembling/assembling, refer to Chapter 4.
1. A set of tools for the debugging port test (test cable, test board, RS-232C cross cable,
display,)
2. A PC with a serial port (for displaying debug port test result)
3. A bootable USB key
4. An external CRT display (for Display troubleshooting)
5. A Card reader (for Card reader slot troubleshooting)
6. An external microphone (for Sound troubleshooting)
7. Headphone (for Sound troubleshooting)
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.2 Troubleshooting Flowchart
Use the flowchart in Figure 2-1 as a guide for determining which FRU is malfunctioning.
Before going through the flowchart steps, check the following:
Ask the user if a password is registered and, if it is, ask him or her to enter the
password.
Make sure that Toshiba Windows VISTA(TM) is installed on the hard disk. Non-
Toshiba operating systems can cause the computer malfunction.
Make sure all optional equipment is removed from the computer.
Make sure the HDD and optical drive bays are empty.
2-6
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
1
Perform the Keyboard/Touch
pad Troubleshooting
No
Do typed characters appear correctly?
Procedures in section 2.6
Yes
Use the diagnostic HDD and run
the diagnostics test program.(PC
reboot is required)
Refer to section 3.2 to start
the diagnostic test program
Is the diagnostic test loaded?
Yes
Perform each diagnostic test
After conforming which diagnostic test
has detected an error, perform the
appropriate procedures as outlined
below.
Is an error detected by any of the
diagnostic tests?
Yes
No
System is normal.
END
Figure 2-1 Troubleshooting flowchart (2/2)
2-8
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
If the diagnostics program cannot detect an error, the problem may be intermittent. The
Running Test program should be executed several times to isolate the problem. Check the
Log Utilities function to confirm which diagnostic test detected an error, then perform the
appropriate troubleshooting procedures as follows:
1. If an error is detected on the system test, memory test, real timer test, perform the
Main Board Troubleshooting Procedures in Section 2.4.
2. If an error is detected on the hard disk test, perform the HDD Troubleshooting
Procedures in Section 2.5.
3. If an error is detected on the keyboard test, perform the Keyboard and Touch pad
Troubleshooting Procedures in Section 2.6.
4. If an error is detected on the display test, perform the Display Troubleshooting
Procedures in Section 2.7.
5. If an error is detected on the CD-ROM/DVD-ROM test, perform the Optical Drive
Troubleshooting Procedures in Section 2.8.
6. If an error is detected on the modem test, perform the Modem Troubleshooting
Procedures in Section 2.9.
7. If an error is detected on the LAN test, perform the LAN Troubleshooting Procedures
in Section 2.10.
8. If an error is detected on the Wireless LAN test, perform the Wireless LAN
Troubleshooting Procedures in Section 2.11.
9. If an error is detected on the sound test, perform the Sound Troubleshooting
Procedures in Section 2.12.
10. If an error is detected on card reader, perform the card reader Slot Troubleshooting
Procedures in Section 2.13.
11. If an error is detected on PCI Express, perform the PCI Express Slot Troubleshooting
Procedures in Section 2.14.
12. If an error is detected on Fingerprint board, perform the Fingerprint board
Troubleshooting Procedures in Section 2.15.
13. If an error is detected on Bluetooth, perform the Bluetooth Troubleshooting
Procedures in Section 2.16.
14. If an error is detected on 3G, perform the 3G Troubleshooting Procedures in Section
2.17.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
15. If an error is detected on camera, perform the camera Troubleshooting Procedures in
Section 2.18.
2-10
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.3 Power Supply Troubleshooting
The power supply controls many functions and components. To determine if the power
supply is functioning properly, start with Procedure 1 and continue with the other Procedures
as instructed. The procedures described in this section are:
Procedure 1: Icons in the LCD Check
Procedure 2: Error Code Check
Procedure 3: Connection Check
Procedure 4: Charge Check
Procedure 5: Replacement Check
Procedure 1
Icons in the LCD Check
The following Icons in the LCD indicate the power supply status:
Battery icon
DC IN icon
The power supply controller displays the power supply status through the Battery icon and
the DC IN icon in the LCD as listed in the tables below. To check the power supply status,
install a battery pack and connect an AC adaptor.
Table 2-1 Battery icon
Battery icon
Lights orange
Lights white
Power supply status
Battery has been charging and AC adaptor is connected.
Battery is fully charged and AC adaptor is connected.
Flashes orange
Battery charge is low. The AC adaptor must be connected to recharge
the battery.
Doesn’t light
Any condition other than those above.
Table 2-2 DC IN icon
DC IN icon
Lights white
Power supply status
DC power is being supplied from the AC adaptor.
Any condition other than those above.
Doesn’t light
2-10
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Comment [z3]: Please provide more
detail how to get Error code.
Procedure 2
Error Code Check
If the power supply microprocessor detects a malfunction, it indicates the error code as
shown below.
The error code begins with the least significant digit.
Table 2-3 Error code
Error code
N0FB*
Where Error occurs
Battery
N0FT*
Power ON/OFF
Power management
N0FU*
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Check 1 Compare the patterns in the hexadecimal error code to the tables below.
Battery
Error code
Meaning
N0FB01
FCC、LMD under Spec.
N0FB02
N0FB03
N0FB04
N0FB05
N0FB06
N0FB07
N0FB08
N0FB09
N0FB0A
N0FB0B
N0FB0C
N0FB0D
N0FB0E
N0FB0F
N0FB0G
N0FB0H
N0FB0J
N0FB0K
N0FB0L
N0FB0M
Initial Data of FCC、LMD is without updating
Battery Learning abnormal function
Battery Check Error
No battery Icon in Windows
Battery data is locked
Abnormal Display on Battery LED
Battery PIC VERSION ERROR
RTC battery current in abnormal condition
Battery On/Off function Error
Unseal error
Communication Fail
To charge&To Discharge electricity fail
Vcc is Fail
Temperature fail
EEeprom address check error(Bq2060)
Ovp fail
Uvp fail
Cfc fail
No battery Icon in SideShow
assistant Battery Check Error
2-12
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Power ON/OFF
Error code
Meaning
N0FT01
N0FT02
N0FT03
N0FT04
N0FT05
N0FT06
N0FT07
N0FT08
N0FT09
N0FT0A
N0FT0B
N0FT0C
N0FT0D
N0FT0E
Cannot Boot Up
System Hang UP when Boot UP
Repeat Boot UP
Auto Shutdown
System Hang Up when Run-In Test
Cannot Power Off by ON/OFF Switch
Can't Soft Power ON and Power OFF
Power On Error by Battery Input only
Reset Key Test Error
Can't auto boot up when insert Adaptor
Can't boot up by fast key.
Can't auto slot on boot up with Slot in ODD.
Cannot Boot Up by novo key
system hang on when Power Off
Power management
Error code
Meaning
N0FU01
N0FU02
N0FU03
N0FU04
N0FU05
N0FU06
N0FU07
N0FU08
N0FU09
N0FU0A
N0FU0B
N0FU0C
Cannot restore after Dos Suspend
System Hang Up after DOS Wake Up
Cannot Run Dos Suspend
Cannot restore after Windows Standby
System Hang Up after Windows Wake Up
Cannot Run Windows Standby
Suspend to disk failed
Power Management System Fail
MAX error fail
Cannot restore after Linux Standby
System Hang Up after Linux Wake Up
Linux Standby function error
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Check 2 In the case of error code N0FT0A:
Make sure the AC adaptor cord and AC power cord are firmly plugged into
the DC IN 19 V socket and wall outlet. If the cables are connected correctly,
go to the following step:
Connect a new AC adaptor and/or AC power cord, if necessary. If the error
still exists, go to Procedure 5.
Check 3 In the case of error code N0FB04:
Make sure the battery pack is correctly installed in the computer. If the
battery pack is correctly installed, go to the following step:
Replace the battery pack with a new one. If the error still exists, go to
Procedure 5.
Check 4 For any other error, go to Procedure 5.
2-14
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 3
Connection Check
The power supply wiring diagram is shown below:
Any of the connectors may be disconnected. Perform Check 1.
Check 1 Disconnect the AC power cord from the wall outlet. Check the power cable for
breaks. If the power cord is damaged, connect a new AC power cord. If there is
no damage, go to Check 2.
Check 2 Make sure the AC adaptor cord and AC power cord are firmly plugged into the
DC-IN jack socket and AC adaptor inlet/wall outlet, respectively. If these cables
are connected correctly, go to Check 3.
Check 3 Make sure the DC IN jack is firmly connected to the connector J7701 on the main
board.
If the DC IN jack is not firmly connected, go to Procedure 5.
If it is connected, go to Check 4.
Check 4 Use a multimeter to make sure the AC adaptor output voltage is close to 19 V. If
the output is several percent lower than 19 V, go to Check 5. If the output is close
to 19 V, go to Check 6.
Check 5 Connect a new AC adaptor or AC power cord.
If the DC IN icon does not light, go to Procedure 5.
If the battery icon does not light, go to Check 6.
Check 6 Make sure the battery pack is installed in the computer correctly. If the battery is
properly installed and the battery icon still does not light, go to Procedure 4.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 4
Charge Check
The power supply may not charge the battery pack. Perform the following procedures:
1. Reinstall the battery pack.
2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to
Procedure 5.
Check 1 Make sure the AC adaptor and AC power cord is firmly plugged into the DC IN
socket and the wall outlet. If these cables are connected correctly, replace the AC
adaptor (and/or AC power cord, if necessary).
Check 2 Make sure the battery is properly installed. If the battery is properly installed, go
to Check 3.
Check 3 The battery pack may be completely discharged. Wait a few minutes to charge the
battery pack. If the battery pack is still not charged, go to Check 4.
Check 4 The battery’s temperature is too hot or cold. Return the temperature to a normal
operating condition. If the battery pack still is not charged, go to Check 5.
Check 5 Replace the battery pack with a new one. If the battery pack still is not charged,
go to Procedure 5.
2-16
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 5
Replacement Check
The main board processor module may be disconnected or damaged. Disassemble the
computer following the steps described in Chapter 4, Replacement Procedures. Check the
connection between the AC adaptor and main board and connection. After checking the
connections, perform the following Check 1:
Check 1 Replace the AC adaptor with a new one. If the AC adaptor is still not functioning
properly, perform Check 2.
Check 2 Replace the main board with a new one following the steps described in Chapter
4, Replacement Procedures.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.4 Main Board Troubleshooting
This section describes how to determine if the main board and CPU are defective or not
functioning properly. Start with Procedure 1 and continue with the other procedures as
instructed.
The procedures described in this section are:
Procedure 1: Message Check
Procedure 2: Diagnostic Test Program Execution Check
Procedure 3: Replacement Check
2-18
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 1
Message Check
When the power is turned on, the system performs the Power On Self Test (POST) installed
in the BIOS ROM. The POST tests each IC on the main board and initializes it.
If an error message is shown on the display, perform Check 1.
If Toshiba MS-DOS or Windows VISTA(TM) is properly loaded, go to Procedure 2.
Check 1 If one of the following error messages appears on the screen, press F1 as the
message instructs. These errors occur when the system configuration preserved in
the RTC memory (CMOS type memory) is not the same as the actual
configuration or when the data is lost.
Press F1 as the message instructs to return all system settings to their default
values. Then the system reboots. Press F2 to run setup.
If an error message (a) appears often when the power is turned on, replace the
RTC battery. If any other error message displays, perform Check 2.
(a) CMOS Battery Low
Press F2 to Run Setup, Press F1 to Load Default
Values and Continue.
(b) RAM READ/WRITE Test Failed
Press F2 to Run Setup, Press F1 to Load Default
Values and Continue.
(c) CMOS DATE/TIME Not Set
Press F2 to Run Setup, Press F1 to Load Default
Values and Continue.
(d) CMOS Settings Wrong
Press F2 to Run Setup, Press F1 to Load Default
Values and Continue.
(e) Primary Master Hard Disk Error
Press F2 to Run Setup, Press F1 to Load Default
Values and Continue.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Check 2 The POST checks the main board. When the POST detects an error, the system
stops or an error message appears.
If one of the following error messages (1) through (3), (5) or (11) appears, go to
Procedure 3.
If the error message (12), (13) appears, go to the Keyboard Troubleshooting
Procedures in Section 2.7.
If the error message (15) appears, go to the HDD Troubleshooting Procedures in
Section 2.6.
(1).
(2).
(3).
(4).
(5).
(6).
(7).
(8).
(9).
Refresh timer test failed
KBC BAT Test failed
RAM R/W test failed
KBC BAT Test failed
CMOS Battery Low
CMOS Settings Wrong
CMOS Date/Time Not Set
DMA Controller Error
DMA-1 Error
(10). DMA-2 Error
(11). Timer Error
(12). Keyboard/Interface Error
(13). PS2 Keyboard not found
(14). PS2 Mouse not found
(15). Primary Master Hard Disk Error
2-20
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Diagnostic Test Program Execution Check
Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, Tests and
Diagnostics, for more information on how to perform these tests.
Comment [z4]: How about Hard disk
test and mouse test ?
1. Check MAIN Ver
D. KB Test
2. Model, BIOS and CPU Test E. MEMSIZE Test
3. Check MAC Test
4. ACIN Test
F. FNTEST Test
G. LEDALL Test
H. STORE Test
I. LED/LCDEDID Test
J. MSCARD Test
K. SDCARD Test
L. HDD Test
5. Temperature Test
6. USB Test
7. USBCCD Test
8. PAD Test
9. LCDRGB Test
A. BLUETOOTH Test
B. VGA Test
M. BATT Test
N. Touch LED Test
O. Auto Run
C. Auido Test
If an error is detected during these tests, go to Procedure 3.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 3
Replacement Check
The main board connectors may be disconnected. Disassemble the computer following the
steps described in Chapter 4, Replacement Procedures and perform Check 1.
Check 1 Visually check for the following:
a) Cracked or broken connector housing
b) Damaged connector pins
If their connectors are in good condition, but there is still a problem, go to Check
2.
Check 2 The main board may be damaged. Replace the main board with a new one
following the steps described in Chapter 4, Replacement Procedures.
2-22
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.5 HDD/SSD Troubleshooting
This section describes how to determine if the HDD/SSD is functioning properly. Perform
the steps below starting with Procedure 1 and continuing with the other procedures as
required.
Procedure 1: Message Check
Procedure 2: Partition Check
Procedure 3: Format Check
Procedure 4: Diagnostic Test Program Execution Check
Procedure 5: Connector Check and Replacement Check
CAUTION: The contents of the hard disk will be erased when you execute the HDD
troubleshooting procedures. Transfer the contents of the hard disk to other
storage media.
Procedure 1
Message Check
When the computer’s HDD/SSD does not function properly, some of the following error
messages may appear on the display. Start with Check 1 below and perform the other checks
as instructed.
Check 1 If either of the following messages appears, go to Procedure 2. If the following
messages do not appear, perform Check 2.
Insert system disk in drive
Press any key when ready .....
or
Non-System disk or disk error
Replace and press any key
Check 2 Make sure the Hard Disk option is set to not used. If it is set to not used, choose
another setting and restart the computer. If the problem still exists, go to
Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Partition Check
Insert the bootable USB key, restart the computer with Esc key pressing down. and choose
boot from USB device. Perform the following checks:
Check 1 Type C:and press Enter. If you cannot change to drive C, go to Check 2. If you
can change to drive C, go to Check 3.
Check 2 Type FDISKand press Enter. Choose Display Partition Information from the
FDISK menu. If drive C is listed, go to Check 3. If drive C is not listed, return to
the FDISK menu and choose the option to create a DOS partition on drive C.
Restart the computer from the Toshiba MS-DOS system disk. If the problem still
exists, go to Procedure 3.
Check 3 If drive C is listed as active in the FDISK menu, go to Check 4. If drive C is not
listed as active, return to the FDISK menu and choose the option to set the active
partition for drive C. Restart the computer and then go to Procedure 3.
Check 4 Remove the USB key and restart the computer. If the problem still exists, go to
Procedure 3.
Check 5 Using the SYS command on the Toshiba MS-DOS system disk, install system
files on the HDD/SSD.
If the following message appears on the display, the system files have been
transferred to the HDD/SSD. Restart the computer. If the problem still exists, go
to Procedure 3.
System transferred
NOTE: If the computer is running Windows 2000, OSR2 or higher and the hard disk has
more than 512 MB capacity, the FDISK program will ask if you need support for
a partition larger than 2GB. Select Y for large partition support; however, be
sure to read the precaution regarding access by other operating systems.
2-24
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 3
Format Check
The computer’s HDD/SSD is formatted using the low level format program and the MS-DOS
FORMAT program. To format the HDD/SSD, start with Check 1 below and perform the
other steps as required.
Check 1 Format the HDD/SSD and transfer system files using FORMAT C:/S/U. If the
following message appears on the display, the HDD/SSD is formatted.
Format complete
If an error message appears on the display, refer to the Toshiba MS-DOS Manual
for more information and perform Check 2.
Check 2 Using the Diagnostics Disk, format the HDD/SSD with a low level format option.
Refer to Chapter 3, Tests and Diagnostics for more information about the
diagnostic program.
If the following message appears on the display, the HDD/SSD low level format
is complete. Partition and format the HDD/SSD using the MS-DOS FORMAT
command.
Format complete
If you cannot format the HDD/SSD using the Tests and Diagnostic program, go to
Procedure 4.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 4
Diagnostic Test Program Execution Check
The HDD/SSD test program is stored in the Diagnostics Disk. Perform all of the HDD/SSD
tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more
information about the HDD/SSD test program.
If an error is detected during the HDD/SSD test, an error code and status will be displayed.
Replace the HDD/SSD with a new one following the instructions in Chapter 4, Replacement
Procedures. The error codes and statuses are listed in Table 2-7. If an error code is not
generated or the problem still exists, go to Procedure 5.
Table 2-4 HDD/SSD error code and status
Code
Status
Can't Detect HDD when Boot Up/Detect wrong model name lf HD
HDD Data Error
N0FH01
N0FH02
N0FH03
N0FH04
N0FH05
N0FH06
N0FH07
N0FH08
N0FH09
N0FH0A
N0FH0B
N0FH0C
N0FH0D
N0FH0E
HDD ATA/100 check error
HDD Type error
Hmonitor test fail
HDD Firmware version error
Shipping HDD restore ERROR
Shipping OS has been booted
Shipping OS version error
shipping OS boot table error
HDD Heating test Fail
RAID function error
2nd HDD function error
SSD function error
Procedure 5
Connector Check and Replacement Check
The HDD/SSD may be disconnected, or the HDD/SSD or the main board may be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the HDD is firmly connected to CON6001 on the main board. Make
sure the SSD is firmly connected to CON6003 on the main board
2-26
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
If any of the connections are loose, reconnect firmly and repeat Procedure 1. If
there is still an error, go to Check 2.
Check 2 The HDD/SSD may be damaged. Replace it with a new one following the
instructions in Chapter 4, Replacement Procedures. If the problem still exists,
perform Check 3.
Check 3 The Main board may be damaged. Replace it with a new one following the
instructions in Chapter 4, Replacement Procedures.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.6 Keyboard and Touch pad Troubleshooting
To determine if the computer’s keyboard or touch pad is functioning properly, perform the
following procedures. Start with Procedure 1 and continue with the other procedures as
instructed.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Execute the Keyboard Test in the Diagnostic Program. Refer to Chapter 3, Tests and
Diagnostics, for more information on how to perform the test program.
If an error occurs, go to Procedure 2. If an error does not occur, the keyboard is functioning
properly.
2-28
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Connector Check and Replacement Check
The keyboard, touch pad or sensor/switch board may be disconnected or damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures, and perform the following checks:
1. If the keyboard or AccuPoint malfunctions, start with Check 1.
2. If the touch pad malfunctions, start with Check 3.
3. If the power switch, InTouch button or Presentation button malfunctions, start with
Check 5.
Check 1 Make sure the keyboard cable is securely connected to CON4801 on the main
board.
If the connection is loose, reconnect firmly. If there is still an error, go to Check 2.
Check 2 The keyboard or its cable may be damaged. Replace it with a new one following
the instructions in Chapter 4, Replacement Procedures. If the problem still exists,
perform Check 5.
Check 3 Make sure the touch pad cable is firmly connected to M1tp_Con1 on the touch
pad board.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
If the connection is loose, reconnect firmly. If there is still an error, go to Check 4.
Check 4 The touch pad or the touch pad cable may be damaged. Replace it with a new one
following the instructions in Chapter 4, Replacement Procedures. If the problem
still exists, perform Check 5.
Check 5 The main board may be damaged. Replace it with a new one following the
instructions in Chapter 4, Replacement Procedures.
2-30
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.7 Display Troubleshooting
This section describes how to determine if the computer’s display is functioning properly.
Start with Procedure 1 and continue with the other procedures as instructed.
Procedure 1: External Monitor Check
Procedure 2: Diagnostic Test Program Execution Check
Procedure 3: Connector Check and Cable Check
Procedure 4: Replacement Check
Procedure 1
External Monitor Check
Connect an external monitor and turn on the computer. If there is no problem on it, the
internal LCD may be defective. Go to Procedure 3. If there is any problem on the external
monitor, the main board may be defective. Go to Procedure 2.
Procedure 2
Diagnostic Test Program Execution Check
The Display Test program is stored on the computer’s Diagnostics disk. This program checks
the display controller on the main board. Connect the Diagnostics HDD, turn on the
computer and run the test. Refer to Chapter 3, Tests and Diagnostics for details. If an error is
detected, go to Procedure 3.
Procedure 3
Connector Check and Cable Check
Check 1 The LCD and Main board are connected by the LVDS cable. Check the
connections. The connectors may be disconnected or damaged. Disassemble the
computer following the steps described in Chapter 4, Replacement Procedures.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
If the connection is loose, reconnect firmly and restart the computer. If there is still an error,
go to Procedure 4.
Procedure 4
Replacement Check
LCD module and main board are connected to display circuits. Any of these components
may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to
disassemble the computer and then perform the following checks:
Check 1 Make sure the LVDS cable is firmly connected to CON6201 on the main board.
If any of the connections are loose, reconnect firmly and repeat Procedure 1. If
there is still an error, go to Check 2.
Check 2 The LCD may be damaged. Replace it with a new one following the instructions
in Chapter 4, Replacement Procedures. If the problem still exists, perform Check
3.
Check 3 The Main board may be damaged. Replace it with a new one following the
instructions in Chapter 4, Replacement Procedures.
2-32
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.8 Optical Drive Troubleshooting
This section describes how to determine if the optical drive (DVD-ROM and DVD±R/±RW/-
RAM Drive) in the Slim Select Bay is functioning properly. Perform the steps below starting
with Procedure 1 and continue with the other procedures as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
The DVD-ROM and DVD±R/±RW/-RAM Drive test program is stored on the Diagnostics
Disk.
For the test, prepare test Media.
Then connect the Diagnostics HDD, turn on the computer and run the test. Refer to Chapter
3, Tests and Diagnostics, for more information about the diagnostics test procedures.
If any errors occur while executing the DVD-ROM and DVD±R/±RW/-RAM Drive test, go
to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Connector Check and Replacement Check
The optical drive (DVD-ROM and DVD±R/±RW/-RAM Drive) is connected to the main
board. The connectors may be disconnected from the main board or may be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the drive to test is firmly connected to CON6002 on the main board.
If the connection is loose, reconnect firmly and repeat Procedure 1. If there is still
an error, go to Check 2.
Check 2 The drive may be defective or damaged. Replace the drive with a new one. If
there is still an error, go to Check 3.
Check 3 Replace the main board with a new one following the steps in Chapter 4,
Replacement Procedures.
2-34
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.9 Modem Troubleshooting
This section describes how to determine if the computer’s modem is functioning properly.
Perform the steps below starting with Procedure 1 and continuing with the other procedures
as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Insert the LAN/Modem test program in the USB key, turn on the computer and run the test.
Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test
procedures.
If any errors occur while executing the Sound/Modem/LAN test, go to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-35
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Connector Check and Replacement Check
The Modem is installed as an MDC (Modem Daughter Card). If the modem malfunctions,
there may be a bad connection between the MDC and the main board. Or the MDC, main
board or their connectors might be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the MDC is firmly connected to CON6501 by MDC cable on the main
board and the connector of the MDC.
If a connector is disconnected, connect it firmly and repeat Procedure 1. If the
modem is still not functioning properly, perform Check 2.
Check 2 The MDC may be defective or damaged. Replace it with a new one following the
steps in Chapter 4, Replacement Procedures. If the modem is still not functioning
properly, perform Check 3.
Check 3 The modem jack or MDC cable may be defective or damaged. Replace it with a
new one following the steps in Chapter 4, Replacement Procedures. If the modem
is still not functioning properly, perform Check 4.
Check 4 The main board may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures.
2-36
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2.10 LAN Troubleshooting
2 Troubleshooting Procedures
2.10 LAN Troubleshooting
This section describes how to determine if the computer’s LAN is functioning properly.
Perform the steps below starting with Procedure 1 and continue with the other procedures as
required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 1
Diagnostic Test Program Execution Check
Execute the LAN test program available as part of the LAN/Modem test program. Refer to
Chapter 3, Tests and Diagnostics for more information on how to perform the test program.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-37
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.11 Wireless LAN Troubleshooting
This section describes how to determine if the computer’s Wireless LAN is functioning
properly. Perform the steps below starting with Procedure 1 and continuing with the other
procedures as required.
Procedure 1: Transmitting-Receiving Check
Procedure 2: Antenna Connection Check
Procedure 3: Replacement Check
Procedure 1
Transmitting-Receiving Check
Make sure the wireless switch of the computer is turned “On.” If it is not, please turn it on.
Refer to Chapter 3, Tests and Diagnostics for more information on how to perform the test
program.
Check 1 Execute test program for the wireless LAN function to check the transmitting-
receiving function of the wireless LAN. You will need a second computer that can
communicate by the wireless LAN.
If the computer passes the test, the function is correctly working.
If the computer does not pass the test, perform Procedure 2.
2-38
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Antenna Connection Check
The wireless LAN wiring diagram is shown below:
Any of the connections may be disconnected. Disassemble the computer following the steps
described in Chapter 4, Replacement Procedures, and perform the following checks:
Check 1 Make sure the wireless LAN board is firmly connected to CON5701 on the main
board.
If the connector is disconnected, connect it firmly. If the wireless LAN board is
still not functioning properly, perform Check 2.
Check 2 Make sure the wireless LAN antenna cables are firmly connected to the wireless
LAN board.
If the wireless LAN antenna cables are disconnected, connect them firmly. If the
wireless LAN board is still not functioning properly, go to Procedure 3.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-39
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 3
Replacement Check
The wireless LAN antenna, wireless LAN board and the main board are connected to the
circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement
Procedures, for instructions on how to disassemble the computer and then perform the
following checks:
Check 1 The wireless LAN board may be defective or damaged. Replace the board with a
new one following the steps in Chapter 4, Replacement Procedures. If the
problem still exists, perform Check 2.
Check 2 The wireless LAN antenna may be defective or damaged. Replace the antenna
with a new one following the steps in Chapter 4, Replacement Procedures. If the
problem still exists, perform Check 3.
Check 3 The main board may be defective or damaged. Replace the board with a new one
following the instructions in Chapter 4, Replacement Procedures and test the
display again.
2-40
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.12 Sound Troubleshooting
This section describes how to determine if the computer’s sound functions are functioning
properly. Perform the steps below starting with Procedure 1 and continuing with the other
procedures as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check
Procedure 3: Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Insert the Sound test program in the USB key, turn on the computer and run the test. Refer to
Chapter 3, Tests and Diagnostics, for details.
If an error is detected, go to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-41
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 2
Connector Check
The sound function-wiring diagram is shown below:
Any of the connections may be disconnected. Disassemble the computer following the steps
described in Chapter 4, Replacement Procedures and perform the following checks:
If the stereo speakers do not work correctly, perform Check 1.
If the headphone does not work correctly, perform Check 2.
If the microphones do not work correctly, perform Check 3.
Check 1 If the stereo speakers do not work properly, the speaker cable may be
disconnected. Make sure the speaker cable is firmly connected to CON4101 on
the Main board. If the stereo speakers are still not functioning properly, go to
procedure 3.
Check 2 If the headphone does not work properly, the headphone cable may be
disconnected. Make sure the headphone cable is firmly connected to CON4201 on
the Main board. If the sound function still does not work properly, go to
procedure 3.
Check 3 If the microphones do not work properly, the external microphone cable may be
disconnected. When using the external microphone, make sure the external
microphone cable is firmly connected to CON4202 on the Main board. If the
microphones are still not functioning properly, go to procedure 3.
2-42
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
Procedure 3
Replacement Check >>>>
Check 1 If the stereo speakers do not sound properly, the right or left speaker may be
defective or damaged. Replace it with a new one. If the stereo speakers still do not
work properly, go to Check 4.
Check 2 If the headphone does not sound properly, the headphone jack may be defective or
damaged. Replace it with a new one. If the sound function still does not work
properly, go to Check 4.
Check 3 If the microphones do not work properly, the microphone cable may be defective
or damaged. Replace it with a new one. If the microphone still does not work
properly, go to Check 4.
Check 4 The Main board may be defective or damaged. Replace it with a new one.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-43
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 SD Card Slot Troubleshooting
2.13 Card Reader Slot Troubleshooting
This section describes how to determine if the computer’s card reader functions are
functioning properly. Perform the steps below starting with Procedure 1 and continuing with
the other procedures as required.
Procedure 1: Check on Windows VISTA(TM)
Procedure 2: Connector Check and Replacement Check
Procedure 1
Check on Windows VISTA(TM)
Insert an MMC/SD/MS/MS(PRO) card into the slot. Check if the installed Windows
recognizes automatically the MMC/SD/MS/MS(PRO) card and the data in the
MMC/SD/MS/MS(PRO) card can be read.
If the card is not recognized or data are not read, go to Procedure 2.
Procedure 2
Connector Check and Replacement Check
The MMC/SD/MS/MS(PRO) card is connected to CON5001 on the Main board.
Check 1 The MMC/SD/MS/MS(PRO) card and the Main board may be disconnected.
Make sure the MMC/SD/MS/MS(PRO) card is firmly inserted to CON3301 on
the Main board. If not, insert it firmly. If the MMC/SD/MS/MS(PRO) card is still
not functioning properly, perform Check 2.
Check 2 The MMC/SD/MS/MS(PRO) card may be faulty. Replace it with a new one
following the step in Chapter 4 Replacement Procedures. If the problem continues,
perform Check 3.
Check 3 The Main board may be faulty. Replace it with a new one following the step in
Chapter 4 Replacement Procedures.
2-44
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.14 PCI Express Card Slot Troubleshooting
This section describes how to check PCI Express Card slot by inspecting a card with PCI
Express interface.
Procedure 1: Check on Windows VISTA(TM)
Procedure 2: Connector Check and Replacement Check
Procedure 1
Check on Windows VISTA(TM)
Insert a PCI Express Card into the slot. Check if the installed Windows recognizes
automatically the PCI Express Card.
If the card is not recognized, go to Procedure 2.
Procedure 2
Connector Check and Replacement Check
The PCI Express Card is connected to CON5401 on the Main board.
Check 1 The PCI ExpressCard and the Main board may be disconnected. Make sure the
PCI ExpressCard is firmly inserted to CON5401 on the Main board. If not, insert
it firmly. If the PCI ExpressCard is still not functioning properly, perform Check
2.
Check 2 The PCI ExpressCard may be faulty. Replace it with a new one following the step
in Chapter 4 Replacement Procedures. If the problem continues, perform Check
3.
Check 3 The Main board may be faulty. Replace it with a new one following the step in
Chapter 4 Replacement Procedures.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-45
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 SD Card Slot Troubleshooting
2-46
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.15 Fingerprint Board(BTO) Troubleshooting
This section describes how to determine if the computer’s fingerprint board is functioning
properly. Perform the steps below starting with Procedure 1 and continuing with the other
procedures as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Insert the fingerprint board test program in the USB key, turn on the computer and run the
test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics
test procedures.
If any errors occur while executing the fingerprint board test, go to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-47
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 SD Card Slot Troubleshooting
Procedure 2
Connector Check and Replacement Check
The fingerprint board is installed to the touchpad board. If the fingerprint board
malfunctions, there may be a bad connection between the fingerprint board and the touchpad
board. Or the fingerprint board or touchpad board might be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the fingerprint board is firmly connected to M1tp_J1 on the touchpad
board and the connector of the fingerprint board.
If a connector is disconnected, connect it firmly and repeat Procedure 1. If the
fingerprint board is still not functioning properly, perform Check 2.
Check 2 The fingerprint board may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures. If the fingerprint
board is still not functioning properly, perform Check 3.
Check 3 The touchpad board may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures.
2-48
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 Bluetooth(BTO) Troubleshooting
This section describes how to determine if the computer’s Bluetooth is functioning properly.
Perform the steps below starting with Procedure 1 and continuing with the other procedures
as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Insert the Bluetooth test program in the USB key, turn on the computer and run the test.
Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test
procedures.
If any errors occur while executing the Bluetooth test, go to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-49
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 SD Card Slot Troubleshooting
Procedure 2
Connector Check and Replacement Check
The Bluetooth is installed on the main board by Bluetooth cable. If the Bluetooth
malfunctions, there may be a bad connection between the Bluetooth and the main board. Or
the Bluetooth, main board or the Bluetooth cable might be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the Bluetooth is firmly connected to CON6501 by Bluetooth cable on
the main board and the connector of the Bluetooth.
If a connector is disconnected, connect it firmly and repeat Procedure 1. If the
Bluetooth is still not functioning properly, perform Check 2.
Check 2 The Bluetooth may be defective or damaged. Replace it with a new one following
the steps in Chapter 4, Replacement Procedures. If the Bluetooth is still not
functioning properly, perform Check 3.
Check 3 The Bluetooth cable may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures. If the Bluetooth is still
not functioning properly, perform Check 4.
Check 4 The main board may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures.
2-50
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.17 3G(BTO) Troubleshooting
This section describes how to determine if the computer’s 3G is functioning properly.
Perform the steps below starting with Procedure 1 and continuing with the other procedures
as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Insert the 3G test program in the USB key, turn on the computer and run the test. Refer to
Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures.
If any errors occur while executing the 3G test, go to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-51
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 SD Card Slot Troubleshooting
Procedure 2
Connector Check and Replacement Check
The 3G is installed as an 3G card. If the 3G malfunctions, there may be a bad connection
between the 3G and the main board. Or the 3G or main board might be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the 3G is firmly connected to CON5601 on the main board and the
connector of the 3G.
If a connector is disconnected, connect it firmly and repeat Procedure 1. If the 3G
is still not functioning properly, perform Check 2.
Check 2 The 3G may be defective or damaged. Replace it with a new one following the
steps in Chapter 4, Replacement Procedures. If the 3G is still not functioning
properly, perform Check 3.
Check 3 The main board may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures.
2-52
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.18 Camera(BTO) Troubleshooting
This section describes how to determine if the computer’s camera is functioning properly.
Perform the steps below starting with Procedure 1 and continuing with the other procedures
as required.
Procedure 1: Diagnostic Test Program Execution Check
Procedure 2: Connector Check and Replacement Check
Procedure 1
Diagnostic Test Program Execution Check
Insert the camera test program in the USB key, turn on the computer and run the test. Refer
to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test
procedures.
If any errors occur while executing the camera test, go to Procedure 2.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
2-53
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Troubleshooting Procedures
2.16 SD Card Slot Troubleshooting
Procedure 2
Connector Check and Replacement Check
The camera is installed on the main board by camera cable. If the camera malfunctions, there
may be a bad connection between the camera and the main board. Or the camera, main board
or the camera cable might be damaged.
Disassemble the computer following the steps described in Chapter 4, Replacement
Procedures and perform the following checks:
Check 1 Make sure the camera is firmly connected to CON6202 by camera cable on the
main board.
If a connector is disconnected, connect it firmly and repeat Procedure 1. If the
camera is still not functioning properly, perform Check 2.
Check 2 The camera may be defective or damaged. Replace it with a new one following
the steps in Chapter 4, Replacement Procedures. If the camera is still not
functioning properly, perform Check 3.
Check 3 The camera cable may be defective or damaged. Replace the LCD cover with a
new one following the steps in Chapter 4, Replacement Procedures. If the camera
is still not functioning properly, perform Check 4.
Check 4 The main board may be defective or damaged. Replace it with a new one
following the steps in Chapter 4, Replacement Procedures.
2-54
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Chapter 3
Tests and Diagnostics
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Chapter 3 Contents
Tests and Diagnostics..................................................................................................... 3-3
Model,BIOS and CPU Test.................................................................................... 3-8
Web camera Test.................................................................................................. 3-13
PAD Test.............................................................................................................. 3-14
Audio Test............................................................................................................ 3-22
Touch LED Test................................................................................................... 3-37
HDD 3D Protection.............................................................................................. 3-38
Appendix:............................................................................................................. 3-49
3-2
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Tests and Diagnostics
This chapter explains how to use the Diagnostic Test programs to test the functions of the
computer’s hardware modules. The test program should be stored on an optical media disk or
a USB boot memory.
The test program menu will also consist of some programs which test the hardware function
or display the current information of the computer.
To execute the auto run will automatically run all the test programs.
NOTE: Before starting the diagnostics, be sure to follow these steps:
1. Check all cables are connected firmly.
2. Exit any application and close Windows.
3. Check if [All Devices] is selected in the “Device Configure” in SETUP
menu.
4. Set test PC SATA Controller Mode to “Compatibility” in BIOS.
4. After test, remember to set SATA Controller mode back to “AHCI”.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.0.1 Test menu
The Test MENU consists of the following functions.
Please enter the item number to choose and execute the test item.
3-4
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.0.2 Executing the Diagnostic Test
To start the Test PROGRAM on CD-ROM, follow these steps:
1. Burn the test program ISO image to an optical media disk.
2. Insert the optical media disk with the test program into optical device.
3. Turn on the power, and choose boot from optical device.
4. System will automatically run the test program and display the test menu.
5. When the test menu displays, please enter the item number to choose and execute the
test item.
Note:
Please make sure to set test PC SATA Controller Mode to “Compatibility” in BIOS and set
SATA Controller Mode to “ACHI” after test.
If it fails in a test item, press “Ctrl+C” and “Y” back to main menu.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.0.3 Executing the Diagnostic Test
To start the Test PROGRAM on USB boot disk, follow these steps:
1. Please prepare Toshiba PC of Windows VISTA OS.
2. Please copy the file for creating a USB-Bootable memory to PC.
The filename of four files and one folder to copy is shown below.
a) COMMAND.COM
b) Freedos.bss
c) FreeDOSMake.exe
d) KERNEL.SYS
e) Autoexec.bat
f) Folder (USBMakingFolder)
3. Please format USB-memory in FAT mode before creating USB-Bootable memory.
4. And when you create USB-Bootable memory, please use only one USB-memory.
5. Run “FreeDOSMake.exe”. You can create USB-Bootable memory.
6. Unzip and copy whole test program to USB memory, overwrite all files.
3-6
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Please check the check box.
And then click START.
7. Turn on the Toshiba PC which need test, and choose boot from USB device.
8. System will automatically run the test program and display the test menu.
9. When the test menu displays, please enter the item number to choose and execute the test
item.
NOTE:
Please make sure to set test PC SATA Controller Mode to “Compatibility” in BIOS.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.1.1 CPU Test
Check CPU spec same with your fixture
Check Front side bus speed is real (The speed does match that of BIOS setup)
This chapter shows how to use the Diagnostics to test the functions of the CPU speed, type
and CPU ID code.
3.1.1.1. Diagnostic name: CPU.EXE
Diagnostic Version: 2.10 or later version.
3.1.1. 2.Principle and how to use:
a. The CPU diagnostic consists of the following functions.
The CPU types, internal speed and CPU ID.
Read the CPU type, internal speed and CPU ID information from the related address and
check if the information is the same as the customer order.
b. Please refer to the illustration above to see the CPU information.
c. Type “CPU.exe /?” in the Free Dos prompt and you can see more details in the command
line to help you check related information.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.2 Check MAC Test
Check MAC address with the label on the motherboard
This chapter shows how to use the Diagnostics to test the MAC address of the Ethernet
controller.
3.3.1. Diagnostic name: pg8168.exe
Diagnostic Version: 2.00 or later version.
3.3.2. Principle and how to use:
a. The pg8168 diagnostic consists of the following functions.
MAC Address read and checking function.
Command line:
Pg8168.exe /vmac
Read the MAC address from the Ethernet controller ROM and the MAC will appear on the
screen..
3-10
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.3 ACIN Test
Please insert adopter then run this program. This subtest checks if the power port works
properly.
This chapter shows how to use the Diagnostics to test the ACIN functions.
3.3.1 Plug in the power test program will display PASS
3.3.2 Unplug the power to test the program will show Fail.
If it fails in a test item, press “Ctrl+C” and “Y” back to main menu.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.4 Temperature Test
Please execute the Temperature Test from test menu.
Test program will show the current CPU temperature result on RIO_25Ch line.
Temperature Test will also check if system temperature is at 20∘ C ~ 80∘ C.
3-12
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.6 PAD Test
Press both the Left and Right Buttons three times to see if they work properly.
This chapter shows how to use the Diagnostics to test the pointing device functions.
3.8.1. Diagnostic name: PS2.EXE
Diagnostic Version: 1.15 or later version.
3.8.2. Principle and how to use:
a. The PS2 diagnostic tests the following functions.
Right & left button, move function.
Move the cursor and click Left and Right button to ensure the pointing device is working
normally.
Command line: Ps2 – ta – ts – r 3 – l 3 – ae /tp2
-r <n> : At least “n” times to click right button for the right button testing. <n> means 1,2… depend
on user’s setting.
-l <n> : At least “n” times to click left button for the left button testing. <n> means 1,2… depend
on user’s setting.
3-14
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
-t2 : Testing Left and Right button only.
-ae : Auto exit the program after the Left and Right button click time setting have reached the
setting.
/TP2 : PS2 mouse testing, no driver need.
b. Please refer to the illustration above to see the Touchpad test information.
c. Type “PS2.exe /?” in the Free Dos prompt and you can see more details in the command
line to help you check related information
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.7 LCDRGB Test
This subtest displays gradations for following modes. To change the mode, press Enter.
Command: video.exe –i /t 162 99
[Mode 101 640*480 8M]
[Mode 103 800*600 8M]
3-16
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
[Mode 111 640*480 16M]
[Mode 114 800*600 16M]
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3-18
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
[Mode 105 1024*768 8M]
[Mode 117 1024*768 16M]
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
This chapter shows how to use the Diagnostics to test the LCD RGB/WB functions.
3.9.1. Diagnostic name: VIDEO.EXE
Diagnostic Version: 2.25.06 or later version.
3.9.2. Principle and how to use:
a. The VIDEO diagnostic tests following functions.
LCD test for R,G,B and BW.
Command line:
video -p -rc /RGB 111
video -p -gc /RGB 111
video -p -bc /RGB 111
-p: To set a pixel mode to display on the screen.
-rc | -gc | -bc: To set the color display on the screen.
VIDEO /F 117 A514
VIDEO /F 117 0000
VIDEO /F 117 05FE
To set the display mode White, Black and Blue shows on the screen.
b. Please refer to the illustration above to see the VIDEO test information.
c. Type “VIDEO.exe /?” in the Free Dos prompt and you can see more details in the
command line to help you check related information
3-20
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.8 VGA Test
This chapter is part of the test card. This test focus on the function of VGA chip and VRAM.
Note:
It may occur a blue screen for serveral minutes before 3D test when using a USB disk to test.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.10Keyboard Test
Press Fn +F12 to end the test
NOTE:
Press the Fn + F12 to end the test can only work after pressing all keys on the keyboard.
If there are some failure keys which cause the test can not complete, you can NOT use
Fn+ F12 to end test program. Please press “Ctrl + Shift” key (press Ctrl first then press
Shift). And then release “Ctrl + Shift” key (release Shift first then release Ctrl). This hot
key can help to exit the test program directly
This chapter shows how to use the Diagnostic to test the functions of the keyboard.
Diagnostic name: Keyboard.exe
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Command: Keyboard.exe /r trsaeng.map trsaeng.xy trsaeng.cd
a. Please choose the different kind of keyboard language.
b. Display the keyboard on the screen to indicate to the operator checking whether or not
each key is correct.
c. Type each key to finish the program.
3-24
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.11Memory Test
This program will test the memory and shows you the total memory size.
Show the total memory size. Command: mm.exe – t 4 /s
This chapter shows how to use the Diagnostics to test the functions of the memory size,
speed and location.
3.2.2.1 Diagnostic name: SMBUS.EXE
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Diagnostic Version: 1.37 or later version.
3.2.2.2 Principle and how to use:
a. The SMBUS diagnostic consists of the following functions.
Memory sizes, memory speed and memory location.
Command line: a-1. mm -t 4 /s %MSIZE%
“-t 3” defines where the memory size will be tested.
“/s %MSIZE%” set the memory size.
b. Please refer to the illustration above to see the memory information.
c. Type “SMBUS.exe /?” in the Free Dos prompt and you can see more details in the
command line to help you check related information
3-26
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.12Function TEST
Please enter “C” to select the function test. Test program will test several function and show
the test result one by one. (Command: functest.exe /T).
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.13LEDALL Test
Test sequnce:
1. PWRBTN_LED
2. DC-IN LED
white
white
orange
pink
3. PWR_ULED_UP
4. PWR_WLED
5. BAT_ULED_UP
6. BAT_WLED
7. LOGO_LED
8. Light_GI_Led
9. KB_BL_CTRL
orange
pink
white
white
white
3-28
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.14STORE Test [CD/DVD-ROM TEST]
This Program will test if the CD/DVD-ROM works properly, please insert test CD before
test.
This chapter shows how to use the Diagnostics to test the ODD functions.
3.17.1. Diagnostic name: PSATA.EXE
3.17.2. Principle and how to use:
a. The PSATA diagnostic consists of the following functions.
CD/DVD type , CD/DVD F/W.
Command line:
psata -d 3 -rep _ /cm "TSSTcorpCDW/DVD_TS-L462D"
Check the Secondary master IDE device and check if the device name is the same as
“TSSTcorpCDW/DVD_TS-L462D.”
psata -d 3 -rep _ /cf "TO01"
Check the Secondary master IDE device and check if the device is F/W then check if the
F/W version is same as “TO01.”
b. Type “PSATA.exe /?” in the Free Dos prompt and you can see more details in the
command line to help you check related information.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.15LID Switch Test
Run the test using the instructions in the image below.
This chapter shows how to use the Diagnostics to test the LID functions.
3.18.1. Diagnostic name: PMC.EXE
Diagnostic Version: 2.05.
3.18.2. Principle and how to use:
a. The diagnostic of PMC detects whether the lid SW works or not.
After active LID function (close the upper cover) the program will read the EC (Embedded
Controller) controller then use the read data to check if the LID switch function is correct.
b. Type “PMC.exe /?” in the Free Dos prompt and you can see more details in the command
line to help you check related information.
3-30
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.19.1. Diagnostic name: RMS2XX.EXE
Diagnostic Version: 1.02.
3.19.2. Principle and how to use:
Diagnostic provided by vendor which is an MS card test program that checks the MS card’s
read, write and protect function.
a. The diagnostic of RMS2XX detects MS card and read /write data.
3.19.3. Principle and how to use:
Copy data into the card and compare with the master file to see if the data matches.
3-32
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.20.1. Diagnostic name: RSD.EXE
Diagnostic Version: 1.02.
3.20.2. Principle and how to use:
Diagnostic provided by vendor which is an SD card test program that checks the SD card’s
read, write and protect function.
a. The diagnostic of RSD detects SD card and read /write data.
3.20.3. Principle and how to use:
Copy data into the card and compare with the master file to see if the data matches.
3-34
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.19BATTERY Test
The battery test will provide the relate information of battery. This program can also test the
battery charge / discharge function.
You can also find the battery cycle count information on this battery.
NOTE:
Please connect the AC adapter to system in battery charge test.
Please disconnect the AC adapter from system in battery discharge test
3-36
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.21HDD 3D Protection
Place computer in five position as screen shows.
For Field inspection T&D, this program judges by sampling five kinds of data shown below.
No Item
Contents
1
2
Access
platform.
An access platform is leveling.
Test
Fixture
The Fixture which fixes PC by 60 degree inclination is used.
Vibration/shock doesn't take a PCB at the time of T&D inspection.
The display of a test program and the set method of PC are shown below.
Display of a Test Program
3
Test1
The portion which PC and Test-Fixture contact is green.
Set method of PC
Z
Upper
X
3-38
Manual
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Judgment
If all data is less than ranges, it will be OK.
4
Test2
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Rear
Upper
Judgment
If all data is less than ranges, it will be OK.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-39
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
5
Test3
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Right
Upper
Judgment
If all data is less than ranges, it will be OK.
3-40
Manual
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
6
Test4
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Front
Upper
Judgment
If all data is less than ranges, it will be OK.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-41
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
7
Test5
The display of a test program and the set method of PC are shown below.
Display of a Test Program
Set method of PC
Left
Upper
Judgment
If all data is less than ranges, it will be OK.
8
9
Inspection Judgment
If all data is less than ranges, it will be OK.
When an inspection result is O.K., calibration at HPC.
Setting
Calibration
data
3-42
Manual
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
If the position is correct, it will show OK.
If the position is wrong, it will show NG.
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-43
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.12 Read and Write DMI information
This program could read and write below strings from/to DMI block.
1. Manufacture
2. Product Name
3. Version
4. Serial Number
5. Type 11
6. Type 12
DMI information:
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-45
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Read Type 11:
Read Type 12:
Write Type 11（60 bytes）:
Write Type 12 (64 bytes):
3-46
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
Satellite M500/M505/M507/M500D/M505D/M507D Maintenance Manual [CONFIDENTIAL]
3-47
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Tests and Diagnostics
3.23 Auto Run
Please enter “J” to select the auto run function. Test program will auto run all test items one
by one as following sequence.
3-48
[CONFIDENTIAL]Satellite M500/M505/M507/M500D/M505D/M507D Maintenance
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Chapter 4
Replacement Procedures
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Chapter 4
4.1 General ...............................................................................................................6
4.2 Battery pack......................................................................................................14
4.3 Express card......................................................................................................16
4.4 HDD module ....................................................................................................17
4.5 Memory module ...............................................................................................21
4.6 Wireless LAN card...........................................................................................23
4.7 Keyboard ..........................................................................................................26
4-2
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figures
Figure 4-1 Removing the battery pack....................................................................14
Figure 4-2 Pressing the Express card......................................................................16
Figure 4-3 Removing the HDD cover.....................................................................17
Figure 4-5 Removing the HDD connector..............................................................18
Figure 4-7 Removing the first memory ..................................................................21
Figure 4-8 Removing the second memory..............................................................21
Figure 4-12 Removing the keyboard cover ............................................................27
Figure 4-13 Removing the screws ..........................................................................27
Figure 4-17 Removing top cover............................................................................30
Figure 4-18 Removing Bluetooth ...........................................................................32
Figure 4-19 Disconnecting Bluetooth cable ...........................................................32
Figure 4-21 Removing the bracket .........................................................................36
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figure 4-26 Removing cables.................................................................................40
Figure 4-28 Removing ODD ..................................................................................41
Figure 4-29 Removing ODD bracket......................................................................42
Figure 4-30 Removing Main PCB..........................................................................42
Figure 4-32 Removing screw securing bracket ......................................................46
Figure 4-33 Removing DC in cable........................................................................46
Figure 4-35 Removing tapes...................................................................................50
Figure 4-36 Removing LCD ...................................................................................50
Figure 4-38 Unlocking the CPU .............................................................................53
Figure 4-39 Installing the CPU...............................................................................54
Figure 4-40 Applying new thermal pad..................................................................55
4-4
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figure 4-43 Apply new thermal pad on the fan ......................................................58
Figure 4-44 Removing the bezel.............................................................................59
Figure 4-45 Removing the LCD unit......................................................................60
Figure 4-46 Removing the LCD supports...............................................................61
Figure 4-47 Removing the LCD cable....................................................................62
Figure 4-48 Removing the Camera.........................................................................62
Figure 4-49 Disconnecting the CCD cable .............................................................62
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.1 General
This section explains how to disassemble the computer and replace Field Replaceable
Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one.
The chart below is a guide to which FRUs need to be removed in order to remove others.
Always start by removing the battery pack, next, optional items such as the optional
Express card and optional Media card, then follow the line on the chart to determine
which FRU you must remove first in order to repair the one you think is causing the
computer to operate improperly. Refer to the example at the bottom of the page.
How to see the
chart:
This chart shows
which unit(s) you
need to remove
in advance when
you replace one
unit.
Example:
When you want
to replace the
Main PCB, you
need to remove
units in the
hatched boxes
above the box in
which the Main
4-6
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Safety Precautions
Before you begin disassembly, read the following safety precautions and observe them
carefully as you work.
DANGER: 1) Always use the genuine battery that is authorized by Toshiba or
compatible with the unit. Since other battery packs have different
specifications, they may be incompatible with the unit, and may burst
or explode.
Never heat or disassemble the battery pack, as that could cause
leakage of alkaline solution. Never throw the battery pack into a
fire, as that could cause the battery pack to explode.
2) The power supply, FL inverter and other components carry high
voltages. If you need to turn on the power of a partially
disassembled computer to check its operation, be very careful not to
touch connectors or components, in order to avoid the risk of electric
shock.
Also, do not disassemble individual components in first-level
maintenance.
WARNING: 1) Turn off the power and disconnect the AC adaptor from the power
source, to avoid exposure to electric shock.
2) Batteries in the computer retain an electrical charge, so there is
danger of electrical shock even when the computer is disconnected
from an AC power source. Remove any metal jewelry or
accessories such as necklaces, bracelets or rings, in order to reduce
the risk of electric shock. Never work with wet or damp hands.
3) Be careful of edges and corners as these may cut.
CAUTION: 1) When you change a component, be sure the replacement component
meets the required specifications. Never use foreign parts, to avoid
any risk of damage to the computer.
2) To avoid any risk of short-circuit, fire or other internal damage,
never allow any metal objects such as screws or paper clips to fall
into the unit. Be sure to replace screws with the same size as those
removed. Make sure all screws are securely fastened. Loose
screws can cause short circuits, resulting in heat, smoke or fire.
3) Before lifting out a FRU or other component, make sure all cables to
the component have been disconnected, in order to reduce the risk of
accidental electric shock.
4) If you use AC power, be sure to use the cable that came with the
computer or one recommended by Toshiba.
5) Make sure that all replacement components meet the specifications
for the computer and that all cables and connectors are securely
fastened, in order to avoid the risk of electric shock.
6) Some parts inside the computer, such as the CPU and cooling
module, become very hot during operation. Conduct repair work
after they have cooled. Be careful around the CPU and cooling
module to avoid burns.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Before You Begin
Look over the procedures in this section before you begin disassembling the computer.
Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by
removing the AC adaptor and the battery pack as instructed in this section:
1. Do not disassemble the computer unless it is operating abnormally.
2. Use only the correct and approved tools.
3. Make sure the working environment is free from the following elements whether
you are using or storing the computer.
Dust and contaminates
Static electricity
Extreme heat, cold and humidity
4. Make sure the FRU you are replacing is causing the abnormal operation by
performing the necessary diagnostics tests described in this manual.
5. Do not perform any operations that are not necessary and use only the described
procedures for disassembling and installing FRUs in the computer.
6. After removing parts from the computer, place them in a safe place away from the
computer so they will not be damaged and will not interfere with your work.
7. You will remove and replace many screws when you disassemble the computer.
When you remove screws, make sure they are placed in a safe place and identified
with the correct parts.
8. When assembling the computer, make sure you use the correct screws to secure
the various pieces in place. Screw sizes are listed in their corresponding figures.
9. The computer contains many sharp edges and corners, so be careful not to injure
yourself.
10. After you have replaced a FRU, make sure the computer is functioning properly
by performing the appropriate test on the FRU you have fixed or replaced.
4-8
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Disassembly Procedures
The computer has three basic types of cable connectors:
Pressure Plate Connectors
Coaxial Cable Connectors
Normal Pin Connectors
To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s
plastic pressure plate and slide the cable out of the connector. To connect the cable to a
Pressure Plate connector, make sure the pressure plate is fully lifted and slide the cable
into the connector. Secure the cable in place by pushing the sides of the pressure plate
down so the plate is flush with the sides of the connector. Gently pull on the cable to
make sure the cable is secure. If you pull out the connector, connect it again making
sure the connector’s pressure plate is fully lifted when you insert the cable.
Coaxial cables should be disconnected with an antenna coaxial disconnector.
Standard pin connectors are used with all other cables. These connectors can be
connected and disconnected by simply pulling them apart or pushing them together.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Assembly Procedures
After you have disassembled the computer and fixed or repaired the problem that was
causing the computer to operate abnormally, you will need to reassemble the computer.
Install all the removed FRUs following the steps described in the corresponding sections
in this chapter.
While assembling the computer, remember the following general points:
Take your time, making sure you follow the instructions closely. Most
problems arise when you get in a hurry assembling the computer.
Make sure all cables and connectors are securely fastened.
Before securing the FRU or other parts, make sure that screws or the FRU will
not pinch any cables.
Check that all latches are closed securely in place.
Make sure all the correct screws are used to secure all FRUs. Using the
wrong screw can either damage the threads on the screw or the head of the
screw and may prevent proper seating of an FRU.
After installing a FRU in the computer, confirm that the FRU and the computer are
functioning properly.
4-10
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Tools and Equipment
The use of Electrostatic Discharge (ESD) equipment is very important for your safety and
the safety of those around you. Proper use of these devices will increase the success rate
of your repairs and lower the cost for damaged or destroyed parts. The following
equipment is necessary to disassemble and reassemble the computer:
One M2 point size 0 Phillips screwdriver
One M2.5/M3 point size 1 Phillips screwdriver
One screwdriver for stud screw
One 4 mm flat-blade screwdriver
Tweezers, to lift out screws that you cannot grasp with your fingers
ESD mats for the floor and the table you are working on
An ESD wrist strap or heel grounder
Anti-static carpeting or flooring
Air ionizers in highly static sensitive areas
Plastic card the size of a credit card
Antenna coaxial cable disconnector
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Screw Tightening Torque
When you fasten screws, be sure to follow the torque list below.
CAUTION: Overtightening can damage components and screws; undertightening
can result in electrical shorts or other damage if screws or components
come loose.
NOTE: Toshiba recommends that you use an electric screwdriver for quick and easy
operations.
M2
M2.5
M3
0.167 N·m (1.7 kgf·cm)
0.294 N·m (3.0 kgf·cm)
0.549 N·m (5.6 kgf·cm)
NOTE: The computer contains several flathead screws. These screws have less
contact area with the screwdriver, so be careful to press firmly enough to
prevent the screwdriver from slipping out and damaging the screw head.
4-12
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Color of Screw Shaft
To avoid mistakes on the screw length, screw shafts are colored as follows:
Even number length screw:
Odd number length screw:
Special length screw:
brown
white
blue (Screws whose lengths are indicated to
one or more decimal places such as 2.5 mm or 2.8 mm.)
Marking of Screws on the Computer Body
To make maintenance of the computer easier, markings of the kinds of the screws
including the types and lengths of the screws are indicated on the computer body.
Kind of screws
BIND screw
Symbol
B
F
FLAT HEAD screw
SUPER THIN HEAD screw
TAPPING screw
S
T
U
Other screws
(Unique screws, STUD, etc.)
Examples:
6 mm BIND screw
B6
12 mm BIND screw
4 mm FLAT HEAD screw
B12
F4
(Indicates the screwed length in round number regardless the length of the stud.)
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.2 Battery pack
Removing the Battery pack
To remove the battery pack, follow the steps below and refer to Figure 4-1.
CAUTION: When handling battery packs, be careful not to short-circuit the
terminals. Also do not drop, hit or apply impact, do not scratch, break,
twist or bend the battery pack.
1. Turn off the power of the computer.
2. Disconnect the AC adaptor and other external devices from the computer.
3. Turn the computer face down.
4. Release the battery lock. Pull out the battery pack while sliding the battery
latch as shown in the following figure.
NOTE: For environmental reasons, do not throw away a spent battery pack.
Battery latch
Battery lock
Figure 4-1 Removing the battery pack
4-14
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Battery pack
To install the battery pack, follow the steps below and refer to Figure 4-1.
CAUTION: The battery pack is a lithium ion battery, which can explode if not
properly replaced, used, handled or disposed of. For environmental
reasons, collect the spent battery packs. Use only batteries recommended
by Toshiba for replacements.
NOTE: Check the battery’s terminals visually. If they are dirty, wipe them clean with
a dry cloth.
1. Push the battery pack into the battery slot. Make sure the battery pack is installed
securely.
2. Slide the battery lock into the lock position.
3. Connect the AC adaptor and all other external devices to the computer.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.3 Express card
Removing the Express card
To remove the Express card, follow the steps below and refer to Figure 4-2 to 4-3.
CAUTION: Before you remove the Express card, refer to the notebook’s
documentation and to your operating system documentation for proper
procedures and precautions.
1. Turn the computer face up.
2. Press the Express card pop the Express card out.
3. Grasp the Express card and pull it out.
Figure 4-2 Pressing the Express card
Installing the Express card
To install the Express card, follow the steps below and refer to Figure 4-2.
1. Insert the Express card into the card slot.
2. Push it carefully to ensure a firm connection.
4-16
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.4 HDD module
CAUTION: When handling the HDD, do not press the top surface as shown by the
arrow. Hold it by the sides.
Removing the HDD
To remove the HDD, follow the steps below and refer to Figure 4-4 to 4-10.
1. Turn the computer upside down.
2. Loosen the screw (with an e-ring) and remove the HDD cover, underneath which
there also installing the memory module.
Figure 4-3 Removing the HDD cover
3. Remove the following screws securing HDD module.
M23L FLAT HEAD screw
4
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4. Pull the tab of the HDD assembly to remove it from the connector of the HDD
cable. Be careful not to damage the connector.
Figure 4-4 Removing 4 screws securing HDD assembly
NOTE: The following steps describe how to disassemble the HDD assembly,
however, do not disassemble if the HDD is working properly.
5. Place the HDD assembly on a flat surface, remove the HDD connector and then
remove the following screws.
M34L FLAT HEAD screw
4
Figure 4-5 Removing the HDD connector
4-18
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the HDD
To install the HDD, follow the steps below and refer to Figure 4-3 to 4-6.
CAUTION: Do not hold the HDD by its top and bottom flat surfaces. It may
damage the HDD.
1. Seat the HDD in the HDD Holder and secure the following screws.
M23L FLAT HEAD screw
4
2. Install the HDD connector.
3. Put the HDD into its slot and connect the HDD to the connector.
4. Secure them with the following screws.
M34L FLAT HEAD screw
4
CAUTION: Do not apply pressure to the center of the HDD pack. It may damage
the HDD pack. Hold the HDD pack by its corners.
5. Set the HDD cover and secure it with the screw (with an e-ring).
4-20
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.5 Memory module
Removing the Memory module
To remove the memory module, make sure the computer is in boot mode and powered
off, follow the steps below and refer to Figures 4-7 to 4-8.
1. Press two latches outward and remove the first memory.
2. Press two latches outward and remove the second memory.
Figure 4-7 Removing the first memory
Figure 4-8 Removing the second memory
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Memory module
To install the memory module, make sure that the computer is in boot mode and powered
off, follow the steps below and refer to Figures 4-7 to 4-8.
CAUTION: When installing only one memory module, be sure to insert it into slot .
Otherwise, the computer or the memory may not work properly.
Do not touch the connectors on the memory module or on the computer.
Dust and stains on the connectors may cause memory access problems.
1. Insert the second memory into the connector slantwise and press it to connect
firmly.
CAUTION: The power must be turned off when you insert a memory module.
Inserting a memory module with the power on might damage the module
or the computer itself.
Never press hard or bend the memory module.
2. When the power is turned on, the computer automatically checks the memory size.
Confirm that the new memory is detected correctly.
3. Insert the first memory into the connector slantwise and press it to connect firmly.
If the memory is not detected, check that it is connected correctly.
4-22
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.6 Wireless LAN card
Removing the Wireless LAN card
To remove the wireless LAN card, make sure the computer is in boot mode and powered
off, follow the steps below and refer to Figures 4-9 to 4-10.
NOTE: The wireless LAN card is an option.
CAUTION: Do not try to remove the wireless LAN card with the computer turned
on. The computer or the wireless LAN card can be damaged. Do not
touch the connectors on the wireless LAN card module on the computer.
Debris on the connectors may cause wireless LAN card access problems.
1. Loosen the screw (with an e-ring) and remove the Wireless LAN card cover.
Figure 4-9 Remove Wireless LAN card cover
2. Remove one piece of tape and the following screw then the wireless antennas.
M23L
FLAT HEAD screw
2
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
3. Disconnect the wireless LAN card from the connector on the main board. Be
careful not to damage the connector.
Figure 4- 10 Removing screws and disconnecting wireless LAN antennas
4-24
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Wireless LAN card
To install the wireless LAN card, make sure that the computer is in boot mode and
powered off, follow the steps below and refer to Figures 4-9 to 4-10.
CAUTION: Be sure to switch the computer off before installing the wireless LAN
card. Otherwise, the computer or the wireless LAN card may be
damaged.
1. Insert the wireless LAN card into connector at an angle on the main board.
2. Gently push the wireless LAN card down and secure the wireless LAN card with the
following screw.
M23L
FLAT HEAD screw
2
3. Connect the wireless LAN antenna cables (white antenna cable should be
connected with the main connector; black antenna cable should be connected with
the Aux. connector) to the connectors on the wireless LAN card.
4. Paste the piece of tape.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.7 Keyboard
Removing the Keyboard
To remove the keyboard, follow the steps below and refer to Figures 4-11 to 4-14.
1. Remove the screws securing the bottom of the keyboard and the keyboard cover on
the bottom case.
M27L FLAT HEAD screw
1
M23L FLAT HEAD screw
2
M23L
Figure 4-11 Removing the screws securing keyboard
2. Turn the computer over and open the display.
3. Remove the Keyboard cover.
4-26
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figure 4-12 Removing the keyboard cover
4. Remove the following screws securing keyboard.
M23L FLAT HEAD screw
2
Figure 4-13 Removing the screws
5. Lift the keyboard upward a little and turn it face down on the palm rest.
6. Separate the keyboard flexible cable from connector and the keyboard LED cable
from the connector on the main board then remove the keyboard.
Figure 4-14 Disconnecting the keyboard flexible and LED cable
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Keyboard
To install the keyboard, follow the steps below and refer to Figures 4-11 to 4-14.
1. Place the keyboard face down on the top cover.
2. Connect the keyboard flexible cable to connector and the keyboard LED cable to
the connector on the main board.
3. Turn the keyboard face up and set it in place.
4. Secure the keyboard with following two screws.
M23L FLAT HEAD screw
2
5. Make sure that there is no gap between the keyboard and the edge of the top
cover.
6. Put the keyboard cover into its slot and press it.
7. Secure the keyboard and keyboard cover with three screws on the bottom case.
M27L
FLAT HEAD screw
FLAT HEAD screw
1
M23L
2
4-28
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.8 Top cover
Removing the Top cover
To remove the Top cover, follow the steps below and refer to Figures 4-15 to 4-17.
1. Remove the following screws securing the bottom case to the toip case.
M2.55L FLAT HEAD screw
M24L FLAT HEAD screw
M23L FLAT HEAD screw
M27L FLAT HEAD screw
6
6
3
3
M2X3L
M2.5X5
M2X4
M2.5X5
M2X4
M2X7
Figure 4-15 Removing the screws on bottom case
2. Turn the bottom case face up and remove the following screws securing top cover.
M24L FLAT HEAD screw
5
3. Disconnect the connector on the main board
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-29
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Figure 4-16 Removing the screws on top cover and separating the connector
4. Separate the Top cover from the bottom case.
NOTE: remove the top cover according to the direction of the arrow.
1
2
2
3
Figure 4-17 Removing top cover
4-30
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Top cover
To install the top case, follow the steps below and refer to Figures 4-15 to 4-17.
1. Install the Top cover on the bottom case.
2. Secure the following screws on the Top cover.
M24L
FLAT HEAD screw
5
3. Connect cable to connector on the main PCB, and turn the bottom case facedown.
4. Secure the following screws on the bottom case.
M2.55L
M23L
M24L
M27L
FLAT HEAD screw
FLAT HEAD screw
FLAT HEAD screw
FLAT HEAD screw
6
3
6
3
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-31
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.9 Bluetooth
Removing the Bluetooth
To remove the Bluetooth, follow the steps below and refer to Figures 4-18 to 4-19.
1.
2.
3.
Remove two pieces of tape.
Take the bluetooh away from the top cover.
Remove the mylar on the fingerprint board.
Mylar
Tap
Figure 4-18 Removing Bluetooth
4.
Separate the cable from the connector according to the direction of the arrow.
Figure 4-19 Disconnecting Bluetooth cable
4-32
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Bluetooth
To install the Bluetooth, follow the steps below and refer to Figures 4-18 to 4-19.
1. Connect the cable to the Bluetooth.
2. Place the Bluetooth to the top cover.
3. Paste the tape and the mylar.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-33
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.10 Power Button Board
Removing the Power Button Board
To remove the power button board, follow the steps below and refer to Figures 4-20
Remove the following two screws and remove the board.
M23L
FLAT HEAD screw
2
Figure 4-20 Removing the Power Button board
4-34
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the Power Button Board
To install the power button board, follow the steps below and refer to Figures 4-20.
1. Install the Power Button board on the top cover.
2. Secure the following screws on the Top cover.
M23L
FLAT HEAD screw
2
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-35
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.11 Fingerprint module
Removing the fingerprint module
To remove the fingerprint module, follow the steps below and refer to Figures 4-21 to
4-23.
1.
2.
Disconnect the cable.
Remove the following screws then remove the bracket.
M23.5L
FLAT HEAD screw
4
M23L
FLAT HEAD screw
2
M2X3
Figure 4-21 Removing the bracket
Remove the following screws and then take the fingerprint and led board away
M23.5L FLAT HEAD screw 4
3.
4-36
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the LED board
To install the LED board, follow the steps below and refer to Figures 4-21 to 4-23.
1. Securing the board.
2. Install the LED board and the Fingerprint Board on the top cover.
3. Secure the following screws on the Top cover.
M23.5L
FLAT HEAD screw
4
4. Install the bracket then securing the following screws.
M23.5L
FLAT HEAD screw
FLAT HEAD screw
4
M23L
2
5. Connect the cable to the board.
4-38
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.12 Touchpad on-off board
Removing the touchpad on-off board
To remove the touchpad on-off board follow the steps below and refer to Figures 4-24.
1. Remove screws securing the touchpad on-off board then remove the board
M23L
FLAT HEAD screw
1
Figure 4-24 Removing screw securing touchpad on-off board
Installing the Touchpad on-off board
To install the touchpad on-off board, follow the steps below and refer to Figures 4-24.
1. Install the touchpad on-off board on the top cover, securing the following screws.
M23L
FLAT HEAD screw
1
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-39
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.13 Main PCB
Remove the main PCB
To remove the main PCB, follow the steps below and refer to Figures 4-25 to 4-30.
1. Remove 7 pieces of tape and the LVDS screw.
M2X2.5
FLAT HEAD screw
1
2. Remove cables on the main PCB.
Figure 4-25 Removing tapes and LVDS screw
Figure 4-26 Removing cables
4-40
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
3. Remove the following screws.
M2X3 FLAT HEAD screw
M2X4 FLAT HEAD screw
M1.6 X2.5 FLAT HEAD screw
4
6
1
M2X3L
4. Remove the ODD bracket and battery bracket.
M1.6X2.5L
Figure 4-27 Removing screws secure the main PCB
5. Remove the ODD module.
Figure 4-28 Removing ODD
6. Remove the following screws and take the ODD bracket away.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-41
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
M22.5L
FLAT HEAD screw
2
Figure 4-29 Removing ODD bracket
7. Lift the main PCB on the right side then remove it from the bottom case.
Figure 4-30 Removing Main PCB
4-42
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the main PCB
To install the main PCB, follow the steps below and refer to Figures 4-25 to 4-30.
1. Securing the bracket to the ODD.
M22.5L
FLAT HEAD screw
2
2. Place the Main PCB to the bottom case
3. Install the ODD to the Main PCB
4. Secure the main PCB to the bottom case using the following screws.
M2X3 FLAT HEAD screw
M2X3 FLAT HEAD screw
4
6
1
M1.6 X2.5 FLAT HEAD screw
5. Connector the cable to the main PCB.
6. Securing the LVDS cable.
M2X2.5
FLAT HEAD screw
1
7. Paste 7 pieces of tape.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-43
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.14 LAN Board
Remove the LAN board
To remove the LAN Board, follow the steps below and refer to Figures 4-31.
1. Remove following screw securing the LAN board.
M24L
FLAT HEAD screw
1
2. Remove the LAN board.
Figure 4-31 Removing screw securing LAN board
Installing the main PCB
To install the main PCB, follow the steps below and refer to Figures 4-31.
1. Install the LAN board.
2. Securing the LAN board with following screw.
M24L
FLAT HEAD screw
1
4-44
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-45
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.15 D/C IN Cable
Remove D/C in cable
To remove the D/C in cable, follow the steps below and refer to Figures 4-32.
1. Remove the black mylar.
2. Remove following screw securing the bracket.
M24L
FLAT HEAD screw
1
3. Remove the bracket.
Figure 4-32 Removing screw securing bracket
4. Remove the DC in cable.
Figure 4-33 Removing DC in cable
4-46
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the AC Power cable
To install the D/C in cable, follow the steps below and refer to Figures 4-32 to 4-33.
1. Install the D/C in cable.
2. Install the bracket and securing the following screw.
M24L
FLAT HEAD screw
1
3. Paste the mylar.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-47
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.16 Speaker
Remove the speaker
To remove the Speaker, follow the steps below and refer to Figures 4-57.
1. Remove the following screws securing the speaker.
M22L
Stand off screw
5
2. Remove the speaker from the bottom case.
Figure 4-34 Removing screws securing speaker
4-48
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the speaker
To install the speaker, follow the steps below and refer to Figures 4-34.
1. Install the speaker.
2. Securing the following screw.
M22L
Stand off screw
5
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-49
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.17 Remove LCD Module
To remove the LCD module, follow the steps below and refer to Figures 4-35 to 4-36.
1. Remove 6 pcs of tapes
Figure 4-35 Removing tapes
2. Remove the following three screws securing the hinge.
M2.55L
FLAT HEAD screw
4
3. Remove the LCD moduls
Figure 4-36 Removing LCD
4-50
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing LCD Module
To install the LCD module, follow the steps below and refer to Figures 4-35 to 4-36.
1. Install the LCD Module and securing the hinge with following screws.
M2.55L
FLAT HEAD screw
4
2. Arrange the cable.
3. Paste the tapes on the bottom case.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-51
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.18 CPU Heat sink/CPU
Removing the CPU Heat sink
To remove the heat sink, follow the steps below and refer to Figures 4-37 to 4-38.
CAUTION:1) The CPU can become very hot during operation. Be sure to let it
cool before starting repair work.
2) When you remove the CPU, replace the thermal pad on the bottom
of heat sink with a new one before installing.
1. Turn the main PCB over and remove the following screws securing the CPU heat
sink and remove it.
M23L
FLAT HEAD screw
6
Figure 4-37 Removing screws securing heat sink
CAUTION: Remove the screws in the order of mark “6”,”5”,“4”,“3”, “2” and
“1” on the CPU holder.
4-52
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
2. Unlock the CPU by turning the cam counterclockwise on the CPU socket 180
degrees using a flat-blade screwdriver.
Figure 4-38 Unlocking the CPU
3. Remove the CPU.
CAUTION: When removing the CPU, lift it straight up. Otherwise, pins on the CPU
may be damaged.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-53
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Install the CPU heat sink/CPU.
To install the CPU heat sink/CPU, follow the steps below and refer to Figures 4-39 to
4-41.
1. Make sure the cam is in the open position.
2. Seat the CPU in the CPU socket. Make sure the direction and position of CPU is
correct to avoid damaging pins on the CPU.
CAUTION: Place the CPU as shown below. (Pay attention to the position of the
triangle mark on the CPU.)
3. Secure the CPU by turning the cam on the CPU socket 180 degrees clockwise with a
flat-blade screwdriver (in the order shown in the figure below).
Figure 4-39 Installing the CPU
4. Apply new thermal pad on the heat sink as shown in the following figure. Stick the
thermal pad on heat sink follow the mark. (Be sure to clean off all old pad before
applying new thermal pad).
4-54
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
H000013080
H000013080
Figure 4-40 Applying new thermal pad
5. Install the CPU heat sink
6. Secure the CPU heat sink with the following screws in the numbered order as shown
on the holder.
M23L
FLAT HEAD screw
6
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-55
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.19 VGA Card
Removing the VGA Card
To remove the VGA card, follow the steps below and refer to Figures 4-42.
1. Remove the following screws securing the VGA.
M23L
FLAT HEAD screw
2
2. Remove the VGA Card from the slot at the pop-up angle
Figure 4-42 Removing screws securing VGA Card
Install the VGA Card.
To install the VGA Card, follow the steps below and refer to Figures 4-42.
1. Insert the VGA Card into connector at an angle about 45
2. Secure the VGA Card with the following screws.
M23L
FLAT HEAD screw
2
4-56
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.20 FAN
Removing the Fan
To remove the Fan, follow the steps below and refer to Figures 4-43.
1. Remove the following three screws securing the fan.
M24L
FLAT HEAD screw
3
2. Disconnect the cable from the board.
Figure 4-43 Removing screws securing FAN and disconnecting cable
3. Take the FAN away.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-57
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Install the FAN.
To install the FAN, follow the steps below and refer to Figures 4-43 to 4-44.
1. Apply new thermal pad on the fan as shown in the following figure. Stick the
thermal pad on fan follow the mark. (Be sure to clean off all old pad before
applying new thermal pad).
H000013110
Figure 4-44 Apply new thermal pad on the fan
2. Install the Fan to the main board.
3. Secure the Fan with the following screws.
M24L
FLAT HEAD screw
3
4. Connect the cable.
4-58
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4.21 LCD unit/Camera
Removing the unit/Camera
To remove LCD unit/Camera, follow the steps below and refer to Figures 4-45 to 4-50.
1. Remove the two tape and the following two screws securing the panel.
M2.55L
FLAT HEAD screw
2
2. Remove the panel according to the direction of the arrow
Caution: Please be careful to not break LCD cover glass when LCD unit is
disassembled and assembled. Please refer to video file how to avoid breaking
LCD cover glass when LCD unit is disassembled and assembled.
3
2
1
3
Figure 4-45 Removing the bezel
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-59
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
3. Remove the tape and the screws securing LCD unit then remove the LCD unit
M2.54L
FLAT HEAD screw
6
Figure 4-46 Removing the LCD unit
NOTE: For environmental reasons, do not throw away a malfunctioning LCD unit (or
FL). Please follow local ordinances or regulations for its disposal.
4-60
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
4. Remove the following screws securing the LCD supports and then remove them.
M22.5L
FLAT HEAD screw
6
Figure 4-47 Removing the LCD supports
5. Remove one piece of glass tape on LCD cable connector.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-61
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
6. Disconnect LCD cable from the connector and remove the cable.
Glass tape
Figure 4-48 Removing the LCD cable
7. Remove the Camera from the top case and disconnect the CCD cable from the
camera.
Figure 4-49 Removing the Camera
Figure 4-50 Disconnecting the CCD cable
4-62
[CONFIDENTIAL] SatelliteM500/M500D Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Replacement Procedures
Installing the LCD unit / Camera
To install the LCD unit / Camera, follow the steps below and refer to Figures 4-45 to
4-50.
1. Connect the CCD cable to the Camera.
2. Install the camera to the top case.
3. Connect the LCD cable to the LCD unit
4. Secure one piece of glass tape on LCD cable connector.
5. Seat two LCD supports on the LCD and secure them with the following screws.
M22.5L FLAT HEAD screw
6
CAUTION: When installing the LCD support, do not mistake the left for the right
and vice versa. “L” for the left, “R” for the right and “UP” for the up of
the bracket are marked on the bracket.
6. Seat the LCD unit on the display cover.
CAUTION: Please be careful to not leave dust and fingerprint on LCD cover glass
when LCD unit is disassembled and assembled. Please refer to video file how to avoid
dust and fingerprint on LCD cover glass when LCD unit is disassembled and
assembled.
7. Secure the following screws to attach the LCD unit.
M2.55L FLAT HEAD screw
8. Secure the LCD panel with the following screws.
M2.55L FLAT HEAD screw 2
6
9. Replace the two pieces of tape to the hole of screw.
SatelliteM500/M500D Maintenance Manual [CONFIDENTIAL]
4-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Handling the LCD Module
Appendices
Appendix A
P
Appendix A Handling the LCD Module
Precautions for handling the LCD module
The LCD module can be easily damaged during assembly or disassembly. Observe the
following precautions when handling the LCD module:
1. When installing the LCD module in the LCD cover, be sure to seat it so that it is
properly aligned and maximum visibility of the display is maintained.
2. For the LCD module, be careful to align the four holes at the right side and left side
of the LCD module with the corresponding holes in the LCD cover before securing
the module with four screws.
Do not force the module into place, because stress can affect its performance.
Also, the panel’s polarized surface is easily scarred, so be carefully when handling it.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix A Handling the LCD Module
3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty,
try breathing on the surface to create a light condensate and wipe it again.
If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to
a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel.
4. If water or other liquid is left on the panel’s surface for a long period, it can change
the screen’s tint or stain it. Be sure to quickly wipe off any liquid.
A-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Handling the LCD Module
Appendices
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object,
which could cause breakage or cracks.
6. CMOS-LSI circuits are used in the module, so guard against damage from
electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the
module.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix A Handling the LCD Module
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long
periods.
8. Do not store the module at temperatures below specifications. Cold can cause the
liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
A-4
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A Handling the LCD Module
Appendices
9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin
(amine) or silicon glue (alcohol or oxime). These materials can release gas that can
damage the panel’s polarization.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Board Layout
Appendices
Appendix B Board Layout
B.1 Main Board Front View
Figure B-1 Main board layout (front)
Satellite M500/M50D/M507 Maintenance Manual [CONFIDENTIAL]
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix B Board Layout
Table B-1 Main board connectors (front)
Number
Name
Camera / Int. MIC connector
LVDS connector
CON6202
CON3701
CON6503
CON6601
CON6201
CON4801
CON5602
CON5601
CON6701
CON4803
CON4804
CON6204
CON6203
CON4802
CON4101
CON5401
CON6501
J7701
Power button connector
FUNCTION BRD connector
TouchPanel connector
KB connector
SIM card slot
Mini card connector
LAN BRD connector
Keyboard LED connector
TP ON/OFF connector
FELICA connector
Blue tooth connector
Touch Pad connector
Internal speaker connector
New Card slot
Modem connector
DC IN connector
B-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Board Layout
Appendices
B.2 Main Board Back View
Figure B-2 Main board layout (back)
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix B Board Layout
Table B-2 Main board connectors (back)
Number
Name
CBT_CON1 (HOT BAR) FUNCTION BRD connector
CON3801
CON4901
CON7701
CON6502
CON6001
CON6002
CON6003
CON2101
CON2201
CON5501
CON0701
CON3501
CON5701
CON5001
CON3901
CON6107
CON6106
CON5101
CON4202
CON4201
RGB connector
FAN connector
Battery Connector
DEBUG CARD connector
HDD connector
ODD connector
SSD connector
Memory slot
Memory slot
Mini card connector
AMD HDT Debug connector
Graphics MXM connector
Mini card connector
Media Card slot
HDMI connector
eSATA / USB Combo connector
USB connector
1394 connector
MIC JACK
HP/ SPDIF JACK
B-4
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Board Layout
Appendices
B.3 LAN Board Front and Back View
(Front)
(Back)
Figure B-3 LAN Board layout (front/back)
Table B-3 LAN Board connectors (front/back)
Number
Name
MLCON301
MLCON103
RJ45 / FJ11 JACK
USB JACK
MLCON101 (HOT BAR) LAN board interface
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix B Board Layout
B.4 Touchpad Board Front and Back View
(Front)
(Back)
Figure B-4 Touchpad Board layout (front/back)
Table B-4 Touchpad Board connector (back)
Number
Name
M1tp_Con1
M1tp_J1
Touch Pad Module connector
Touch Pad BD to FP BD connector
M1tp_Con3 (HOT BAR) Touch Pad BD to MB interface
M1tp_Con2 (HOT BAR) Touch Pad BD to LED BD interface
B-6
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Board Layout
Appendices
B.5 LED Board Front and Back View
(Front)
(Back)
Figure B-5 LED Board layout (front/back)
Table B-5 LED Board connectors (back)
Number
Lb_Con1 (HOT BAR)
Name
LED BD to Touch Pad BD interface
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix B Board Layout
B.6 Finger Printer Board Front and Back View
(Front)
(Back)
Figure B-6 Finger Printer Board layout (front/back)
Table B-6 Finger Printer Board connectors (back)
Number
Name
F_J1
PF BD to Touch Pad BD interface
B-8
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Board Layout
Appendices
B.7 Inverter Board Front and Back View
(Front)
(Back)
Figure B-7 Inverter Board layout (front/back)
Table B-7 Inverter Board connectors (front)
Number
Name
CN1
CN2
Input connector
Output connector
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
Appendix C Pin Assignments
Main board
C.1 CON2101 SO-DIMM0 connector (200-pin)
Table C-1 SO-DIMM0 connector (200-pin) (1/3)
Pin No.
1
Signal Name
M_VREF_MCH
GND
I/O
-
Pin No.
2
Signal Name
GND
I/O
-
3
-
4
M_A_DQ61
M_A_DQ63
GND
I/O
I/O
-
5
M_A_DQ58
M_A_DQ57
GND
I/O
I/O
-
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
M_A_DM7
GND
I/O
-
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
M_A_DQS#7
M_A_DQS7
GND
I/O
I/O
-
M_A_DQ59
M_A_DQ62
GND
I/O
I/O
-
M_A_DQ60
M_A_DQ56
GND
I/O
I/O
-
M_A_DQ54
M_A_DQ50
GND
I/O
I/O
-
M_A_DQ51
M_A_DQ55
GND
I/O
I/O
-
M_A_DM6
GND
I/O
-
M_A_DQS#6
M_A_DQS6
GND
I/O
I/O
-
M_CLK_DDR0
M_CLK_DDR#0
GND
-
I/O
I/O
-
M_A_DQ49
M_A_DQ53
GND
I/O
I/O
-
M_A_DQ48
M_A_DQ52
GND
GND
-
GND
-
M_A_DQ42
M_A_DQ45
GND
I/O
I/O
-
M_A_DQ20
M_A_DQ46
GND
I/O
I/O
-
M_A_DQS#5
M_A_DQS5
GND
I/O
I/O
-
NC
-
M_A_DM5
GND
I/O
-
M_A_DQ18
M_A_DQ19
GND
I/O
I/O
-
M_A_DQ44
M_A_DQ47
GND
I/O
I/O
-
M_A_DQ39
I/O
M_A_DQ38
I/O
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
Table C-1 SO-DIMM0 connector (200-pin) (2/3)
Pin No.
63
Signal Name
M_A_DQ32
GND
I/O
Pin No.
64
Signal Name
M_A_DQ34
GND
I/O
I/O
I/O
65
-
66
-
67
M_A_DM4
NC
I/O
68
M_A_DQS#4
M_A_DQ4
GND
I/O
69
-
70
I/O
71
GND
-
72
-
73
M_A_DQ33
M_A_DQ36
GND
I/O
74
M_A_DQ37
M_A_DQ35
GND
I/O
75
I/O
76
I/O
77
-
78
-
79
M_CKE0
+1.8V
I
80
M_CKE1
+1.8V
I
81
-
82
-
83
NC
-
I
84
NC
-
85
M_A_BS2
+1.8V
86
M_A_A14
+1.8V
-
-
87
-
88
89
M_A_A12
M_A_A9
M_A_A8
+1.8V
I/O
I/O
I/O
-
90
M_A_A11
M_A_A7
M_A_A6
+1.8V
I/O
I/O
I/O
-
91
92
93
94
95
96
97
M_A_A5
M_A_A3
M_A_A1
+1.8V
I/O
I/O
I/O
-
98
M_A_A4
M_A_A2
M_A_A0
+1.8V
I/O
I/O
I/O
-
99
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
M_A_A10
M_A_BS0
M_A_WE#
+1.8V
I/O
I
M_A_BS1
M_A_RAS#
M_CS#0
+1.8V
I
I
I
I
-
-
M_A_CAS#
M_CS#1
+1.8V
I
M_ODT0
M_A_A13
+1.8V
I
I
I/O
-
-
M_ODT1
GND
I
NC
-
-
GND
-
M_A_DQ31
M_A_DQ27
GND
I/O
I/O
-
M_A_DQ30
M_A_DQ26
GND
I/O
I/O
-
M_A_DQS#3
M_A_DQS3
I/O
I/O
M_A_DM3
GND
I/O
-
C-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Table C-1 SO-DIMM0 connector (200-pin) (3/3)
Appendices
Pin No.
133
135
137
139
141
143
145
147
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
Signal Name
GND
I/O
-
Pin No.
134
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
200
Signal Name
M_A_DQ24
M_A_DQ28
GND
I/O
I/O
I/O
-
M_A_DQ29
M_A_DQ25
GND
I/O
I/O
-
M_A_DQ23
M_A_DQ21
GND
I/O
I/O
-
M_A_DQ16
M_A_DQ19
GND
I/O
I/O
-
M_A_DQS#2
M_A_DQS2
GND
I/O
I/O
-
M_A_DM2
GND
I/O
-
M_A_DQ22
M_A_DQ17
GND
I/O
I/O
-
M_A_DQ20
M_A_DQ47
GND
I/O
I/O
-
M_A_DQ13
M_A_DQ11
GND
I/O
I/O
-
M_A_DQ15
M_A_DQ9
GND
I/O
I/O
-
NC
-
M_CLK_DDR1
M_CLK_DDR#1
GND
I
GND
-
I
M_A_DQS#1
M_A_DQS1
GND
I/O
I/O
-
-
M_A_DM1
GND
I/O
-
M_A_DQ8
M_A_DQ12
GND
I/O
I/O
-
M_A_DQ14
M_A_DQ10
GND
I/O
I/O
-
M_A_DQ2
M_A_DQ3
GND
I/O
I/O
-
M_A_DQ7
M_A_DQ1
GND
I/O
I/O
-
M_A_DM0
GND
I/O
-
M_A_DQS#0
M_A_DQS0
GND
I/O
I/O
-
M_A_DQ0
M_A_DQ4
GND
I/O
I/O
-
M_A_DQ5
M_A_DQ6
GND
I/O
I/O
-
SMB_DAT_S
SMB_CLK_S
+3VS
I/O
I/O
-
GND
-
GND
-
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.2 CON2201 SO-DIMM1 connector (200-pin)
Table C-2 SO-DIMM1 connector (200-pin) (1/3)
Pin No.
1
Signal Name
M_VREF_MCH
GND
I/O
-
Pin No.
2
Signal Name
GND
I/O
-
3
-
4
M_B_DQ59
M_B_DQ62
GND
I/O
I/O
-
5
M_B_DQ63
M_B_DQ58
GND
I/O
I/O
-
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
M_B_DM7
GND
I/O
-
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
M_B_DQS#7
M_B_DQS7
GND
I/O
I/O
-
M_B_DQ61
M_B_DQ57
GND
I/O
I/O
-
M_B_DQ56
M_B_DQ60
GND
I/O
I/O
-
M_B_DQ48
M_B_DQ51
GND
I/O
I/O
-
M_B_DQ54
M_B_DQ53
GND
I/O
I/O
-
M_B_DM6
GND
I/O
-
M_B_DQS#6
M_B_DQS6
GND
I/O
I/O
-
M_CLK_DDR2
M_CLK_DDR#2
GND
I
I
-
M_B_DQ50
M_B_DQ55
GND
I/O
I/O
-
M_B_DQ49
M_B_DQ52
GND
I/O
I/O
-
GND
-
GND
-
M_B_DQ42
M_B_DQ44
GND
I/O
I/O
-
M_B_DQ40
M_B_DQ45
GND
I/O
I/O
-
M_B_DQS#5
M_B_DQS5
GND
I/O
I/O
-
NC
-
M_B_DM5
GND
I/O
-
M_B_DQ47
M_B_DQ43
GND
I/O
I/O
-
M_B_DQ41
M_B_DQ46
GND
I/O
I/O
-
M_B_DQ35
I/O
M_B_DQ36
I/O
C-4
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Table C-2 SO-DIMM1 connector (200-pin) (2/3)
Appendices
Pin No.
63
Signal Name
M_B_DQ38
GND
I/O
Pin No.
64
Signal Name
M_B_DQ32
GND
I/O
I/O
I/O
65
-
66
-
67
M_B_DM4
NC
I/O
68
M_B_DQS#4
M_B_DQS4
GND
I/O
69
-
70
I/O
71
GND
-
72
-
73
M_B_DQ34
M_B_DQ39
GND
I/O
74
M_B_DQ37
M_B_DQ33
GND
I/O
75
I/O
76
I/O
77
-
78
-
79
M_CKE2
+1.8V
I
80
M_CKE3
+1.8V
I
81
-
82
-
83
NC
-
84
NC
-
85
M_B_BS2
+1.8V
I
86
M_B_A14
+1.8V
-
87
-
88
-
89
M_B_A12
M_B_A9
M_B_A8
+1.8V
I
90
M_B_A11
M_B_A7
M_B_A6
+1.8V
I
91
I
92
I
93
I
94
I
95
-
96
-
97
M_B_A5
M_B_A3
M_B_A1
+1.8V
I
98
M_B_A4
M_B_A2
M_B_A0
+1.8V
I
99
I
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
I
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
I
I
-
-
M_B_A10
M_B_BS0
M_B_WE#
+1.8V
I
M_B_BS1
M_B_RAS#
M_CS#2
+1.8V
I
I
I
I
I
-
-
M_B_CAS#
M_CS#3
+1.8V
I
M_ODT2
M_B_A13
+1.8V
I
I
I
-
-
M_ODT3
GND
I
NC
-
-
GND
-
M_B_DQ30
M_B_DQ31
GND
I/O
I/O
-
M_B_DM25
M_B_DM26
GND
I/O
I/O
-
M_B_DQS#3
M_B_DQS3
GND
I/O
I/O
-
M_B_DM3
GND
I/O
-
M_B_DQ29
I/O
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
Table C-2 SO-DIMM1 connector (200-pin) (3/3)
Pin No.
135
137
139
141
143
145
147
149
151
153
155
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
Signal Name
M_B_DQ24
M_B_DQ27
GND
I/O
I/O
I/O
-
Pin No.
136
138
140
142
144
146
148
150
152
154
156
158
160
162
164
166
168
170
172
174
176
178
180
182
184
186
188
190
192
194
196
198
200
Signal Name
M_B_DQ28
GND
I/O
I/O
-
M_B_DQ23
M_B_DQ19
GND
I/O
I/O
-
M_B_DQ22
M_B_DQ18
GND
I/O
I/O
-
M_B_DQS#2
M_B_DQS2
GND
I/O
I/O
-
M_B_DM2
GND
I/O
-
M_B_DQ17
M_B_DQ20
GND
I/O
I/O
-
M_B_DQ16
M_B_DQ21
GND
I/O
I/O
-
M_B_DQ15
M_B_DQ9
GND
I/O
I/O
-
M_B_DQ10
M_B_DQ11
GND
I/O
I/O
-
NC
-
M_CLK_DDR3
M_CLK_DDR#3
GND
I
GND
-
I
M_B_DQS#1
M_B_DQS1
GND
I/O
I/O
-
-
M_B_DM1
GND
I/O
-
M_B_DQ13
M_B_DQ12
GND
I/O
I/O
-
M_B_DQ14
M_B_DQ8
GND
I/O
I/O
-
M_B_DQ3
M_B_DQ2
GND
I/O
I/O
-
M_B_DQ7
M_B_DQ6
GND
I/O
I/O
-
M_B_DM0
GND
I/O
-
M_B_DQS#0
M_B_DQS0
GND
I/O
I/O
-
M_B_DQ1
M_B_DQ4
GND
I/O
I/O
-
M_B_DQ5
M_B_DQ0
GND
I/O
I/O
-
SMB_DAT_S
SMB_CLK_S
+3VS
I/O
I/O
-
+3VS_SET
GND
-
-
C-6
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.3 CON6002 SATA interface ODD connector (13-pin)
Table C-3 ODD connector (13-pin)
Pin No.
S1
Signal Name
GND
I/O
Pin No.
S2
Signal Name
SATA_TXP2
GND
I/O
I
-
I
S3
SATA_TXN2
SATA_RXN2
GND
S4
-
S5
O
-
S6
SATA_RXP2
O
S7
P1
NC
-
P2
P4
P6
+5VS
NC
-
-
-
P3
+5VS
-
P5
GND
-
GND
C.4 CON6001 SATA interface HDD connector (22-pin)
Table C-4 HDD connector (22-pin)
Pin No.
S1
Signal Name
GND
I/O
-
Pin No.
S2
Signal Name
SATA_TXP1
GND
I/O
I
S3
SATA_TXN1
SATA_RXN1
GND
I
S4
-
S5
O
-
S6
SATA_RXP1
O
S7
P1
+3VS
-
P2
P4
+3VS
GND
GND
+5VS
GND
GND
NC
-
-
-
-
-
-
-
-
P3
+3VS
-
P5
GND
-
P6
P7
+5VS
-
P8
P9
+5VS
-
P10
P12
P14
P11
P13
P15
NC
-
NC
-
NC
-
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.5 CON6003 SATA interface SSD connector (BTO) (24-pin)
Table C-5 SSD connector (24-pin)
Pin
No.
Pin
No.
Signal Name
I/O
Signal Name
I/O
1
3
+5VS
+5VS
+5VS
+5VS
NC
-
-
-
-
-
-
-
-
-
-
-
-
2
+3VS
+3VS
+3VS
+3VS
NC
-
-
4
5
6
-
7
8
-
9
10
12
14
16
18
20
22
24
-
11
13
15
17
19
21
23
GND
NC
GND
-
SATA_TXP0
SATA_TXN0
GND
I
GND
NC
I
-
NC
SATA_RXN0
SATA_RXP0
GND
O
O
-
GND
NC
C-8
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.6 CON5001 Media card connector (45-pin)
Table C-6 Media card connector (45-pin)
Pin No.
1
Signal Name
SD-DAT2
MMC_DAT4
MMC_DAT5
CARD_3V3
CARD_3V3
MS_D3
I/O
I/O
I/O
I/O
-
Pin No.
2
Signal Name
SD_DAT3
SD_CMD
GND
I/O
I/O
I/O
-
3
4
5
6
7
8
GND
-
9
-
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
MS_CLK
MS_INS#
MS_D0
I
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
I/O
I/O
I/O
-
O
I/O
I
MS_D2
MS_D1
MS_BS
GND
SD_CLK
GND
I
MMC_DAT6
MMC_DAT7
SD_DAT1
SD_CD#
XD_CD#
XD_RE#
XD_CLE#
XD_WE#
GND
I/O
I/O
I/O
O
-
SD_DAT0
I/O
GND
-
I
O
XD_RDY
XD_CE#
XD_ALE
XD_WP#
XD_D0
I
I
I
I
I
I
-
I/O
I/O
I/O
I/O
-
XD_D1
I/O
I/O
I/O
I/O
O
XD_D2
XD_D3
XD_D4
XD_D5
XD_D6
XD_D7
CARD_3V3
SD_WP #
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.7 CON4201 H/P interface connector (8-pin)
Table C-7 H/P interface connector (8-pin)
Pin No.
Signal Name
JACK1_D#
HP_JACK_L
JACK2_D#
GND
I/O
I
Pin No.
Signal Name
HP_JACK_R
GND
I/O
1
3
2
4
O
-
O
I
5
JACK_IN
I
A
C
B
-
VCC_SPDIF
-
SPDIF_OUT
O
C.8 CON5701 WLAN Mini Card interface connector (52-pin)
Table C-8 Mini Card interface connector (52-pin)
Pin No.
Signal Name
NC
BT_CHDATA
BT_CHCLK
MINI3CLK_REQ#
GND
CLK_PCIE_MINIC
ARD3#
CLK_PCIE_MINIC
ARD3
I/O
Pin No.
Signal Name
+3VS
GND
+1.5VS
NC
I/O
1
3
5
7
9
-
I/O
I
O
-
2
4
6
8
10
12
-
-
-
-
-
-
NC
11
I
NC
13
I
14
-
NC
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
GND
NC
NC
GND
PCIE_RXN5
PCIE_RXP5
GND
-
-
-
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
NC
GND
WLAN_ON/OFF#
PLTRST#_M
+3VS
GND
+1.5VS
NC
NC
GND
USB_PN5
USB_PP5
GND
WIMAX_LED#
WIFI_LED#
NC
+1.5VS
GND
+3VS
-
-
I
I
-
-
-
-
-
-
O
O
-
-
I
I
-
-
-
-
-
-
-
-
-
GND
PCIE_TXN5
PCIE_TXP5
GND
GND
+3VS
+3VS
GND
NC
NC
-
I/O
I/O
-
O
O
-
-
-
-
NC
NC
C-10
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.9 CON5501 Upconvert Mini Card interface connector(BTO)
(52-pin)
Table C-9 Mini Card interface connector (52-pin)
Pin No.
Signal Name
NC
NC
I/O
-
-
-
O
-
Pin No.
Signal Name
+3VS
GND
+1.5VS
NC
I/O
1
3
5
7
9
2
4
6
8
10
12
-
-
-
-
-
-
NC
MINI1CLK_REQ#
GND
CLK_PCIE_MINI
CARD#
CLK_PCIE_MINI
CARD
NC
11
I
NC
13
I
14
-
NC
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
GND
NC
NC
GND
PCIE_RXN2
PCIE_RXP2
GND
-
-
-
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
NC
GND
-
-
I
WUSB_ON/OFF#
PLTRST#_M
+3VS
GND
+1.5VS
NC
NC
GND
NC
NC
GND
NC
NC
NC
+1.5VS
GND
+3VS
-
I
O
O
-
-
I
I
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
GND
PCIE_TXN2
PCIE_TXP2
GND
GND
+3VS
+3VS
GND
NC
NC
NC
NC
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.10 CON5601 WWAN Mini Card interface connector(BTO)
(52-pin)
Table C-10 Mini Card interface connector (52-pin)
Pin No.
1
Signal Name
I/O
-
-
-
O
-
I
I
-
-
-
-
O
O
-
-
I
I
-
-
-
-
-
-
-
-
-
Pin No.
2
Signal Name
+3VS_WWAN
GND
+1.5VS
SIM_VCC
SIM_DIO
SIM_CLK
SIM_RST
NC
I/O
-
-
-
-
-
-
-
-
-
I
NC
NC
NC
NC
3
5
7
9
4
6
8
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
CLK_PCIE_WWAN#
CLK_PCIE_WWAN
GND
NC
NC
GND
3G_ON
PLTRST#_M
+3VS_WWAN
GND
+1.5VS
NC
GND
I
PCIE_RXN3
PCIE_RXP3
GND
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
GND
PCIE_TXN3
PCIE_TXP3
GND
NC
GND
USB_PN4
USB_PP4
GND
WWAN_LED#
NC
NC
+1.5VS
GND
GND
+3VS_WWAN
+3VS_WWAN
GND
NC
NC
NC
NC
+3VS_WWAN
C-12
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.11 CON5602 SIM Card connector(BTO) (12-pin)
Table C-11 MDC interface connector (12-pin)
Pin No.
C1
Signal Name
SIM_VCC_C
I/O
Pin No.
C2
Signal Name
I/O
I
-
I
SIM_RST
GND
-
C3
C5
SIM_CLK
NC
-
I/O
C6
C7
SIM_DIO
C.12 CON6501 MDC interface connector(BTO) (12-pin)
Table C-12 MDC interface connector (12-pin)
Pin No.
Signal Name
GND
I/O
Pin No.
Signal Name
I/O
-
I
-
-
-
-
-
I
1
3
2
4
NC
NC
ACZ_SDOUT_MDC
GND
-
5
6
+3V
I
7
8
ACZ_SYNC_MDC
ACZ_SDIN1
GND
O
I
9
10
12
GND
11
ACZ_RST#_MDC
ACZ_BCLK_MDC
C.13 CON3901 HDMI connector(BTO) (19-pin)
Table C-13 Modem connector (19-pin)
Pin No.
Signal Name
I/O
Pin No.
Signal Name
GND
I/O
I
I
-
I
I
I
I
I
-
I
I
-
I
I
1
3
2
4
HDMI_TX2+_R
HDMI_TX2-_R
GND
HDMI_TX1+_R
HDMI_TX1-_R
GND
5
6
7
8
HDMI_TX0+_R
HDMI_TX0-_R
GND
9
10
12
14
16
18
HDMI_CLK+_R
HDMI_CLK-_R
NC
11
13
15
17
19
HDMI_CEC
HDMI_DDCCLK_R
GND
I/O
HDMI_DDCDAT_R
+5V_HDMI
O
HDMI_HPD_C
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.14 CON4801 Keyboard interface connector (34-pin)
Table C-14 Keyboard interface connector (34-pin)
Pin No.
1
Signal Name
NUM_LED#
CAP_LED#
KSI1
I/O
Pin No.
2
Signal Name
LEDB_LED#
+5VS
I/O
3
4
5
I
6
KSI6
I
7
KSI5
I
8
KSI0
I
9
KSI4
I
10
12
14
16
18
20
22
24
26
28
30
32
34
KSI3
I
11
13
15
17
19
21
23
25
27
29
31
33
KSI2
I
KSI7
I
KSO15
KSO11
KSO9
O
O
O
O
O
O
O
O
KSO12
KSO10
KSO8
KSO7
KSO14
KSO3
KSO0
KSO2
NC
O
O
O
O
O
O
O
O
KSO13
KSO6
KSO5
KSO4
KSO1
+5VS
NC
NC
NC
+5VS
C.15 CON4802 MB to Touch PAD Board connector (22-pin)
Table C-15
MB to Touch PAD Board connector (22-pin)
Pin No.
Signal Name
+5VSUS
+5VS
I/O
Pin No.
Signal Name
+5V
I/O
1
3
-
-
2
4
-
+5VS
-
5
+3VA
-
6
+3VS
-
7
+3V
-
8
CB_LED#
TP_DAT
GND
I
9
10
12
14
16
HDD_LED#
TP_CLK
LID_SW#
DC_IN_LED#
I
I/O
11
13
15
I/O
O
I
-
I
I
LIGHT_GI_LED#
PWR_WLED#
PWR_ULED_UP
#
17
18
I
I
BAT_WLED#
GND
I
-
19
21
BAT_ULED_UP#
USB_PN2
20
22
I/O
USB_PP2
I/O
C-14
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.16 CON4804 Touch PAD ON/OFF connector (4-pin)
Table C-16
Touch PAD Button connector (4-pin)
Pin No.
Signal Name
I/O
-
Pin No.
Signal Name
NC
GND
I/O
1
3
+5VS
TP_ON
2
4
-
-
O
C.17 CON4202 Microphone In connector (8-pin)
Table C-17 Microphone In connector (8-pin)
Pin No.
Signal Name
A_GND
I/O
Pin No.
Signal Name
MIC_IN_AC_E
MIC_EXT_JD#
I/O
1
3
5
7
-
-
2
4
6
8
I
NC
-
A_GND
A_GND
I
A_GND
-
C.18 CON6503 Power Button connector (8-pin)
Table C-18 Power Button connector (8-pin)
Pin No.
Signal Name
GND
I/O
-
Pin No.
Signal Name
SMB1_CLK
NC
I/O
1
3
5
7
2
4
6
8
I
SMB1_DAT
+3VS
I/O
-
+5V
PWRBTN_LED#
I
PWR_SW#
O
C.19 CON6601 Function Board connector (8-pin)
Table C-19 Function Board connector (8-pin)
Pin No.
Signal Name
+5VA
I/O
Pin No.
Signal Name
+5VS
I/O
1
3
5
7
-
I
2
4
6
8
I
I
LID_SW#
SMB2_DAT_FN
GND
SMB2_CLK_FN
INT_FN
I/O
-
O
-
GND
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.20 CON6701 MB to LAN Board connector (34-pin)
Table C-20 MB to LAN Board connector (34-pin)
Pin No.
Signal Name
+3VS
I/O
Pin No.
Signal Name
SUSCLK_FM
SMB_CLK_FM
FM_AUDIO_R
INTX_FM#
I/O
1
3
2
4
I
I
GND
5
SMB_DAT_FM
FM_AUDIO_L
+3VSUS
I/O
6
I
7
I
-
I
8
I
9
10
12
+3VSUS
-
11
PCI_RST#
PCIE_WAKE#
O
PCIE_LOM_CLK
REQ#
13
14
O
GND
-
15
17
19
21
23
25
27
29
31
33
PCIE_RXP1
GND
O
16
18
20
22
24
26
28
30
32
34
PCIE_RXN1
PCIE_TXP1
GND
O
-
I
PCIE_TXN1
CLK_PCIE_LAN
GND
I
-
I
-
CLK_PCIE_LAN#
+5V_USB
+5V_USB
+5V_USB
USB_PP0
USB_PN1
GND
I
-
+5V_USB
+5V_USB
USB_PN0
GND
-
-
-
-
I/O
-
I/O
I/O
-
USB_PP1
I/O
C.21 CON4101 Speaker connector (4-pin)
Table C-21 Speaker connector (4-pin)
Pin No.
Signal Name
H_SPKR-
I/O
O
Pin No.
Signal Name
H_SPKR+
H_SPKL+
I/O
O
1
3
2
4
H_SPKL-
O
O
C.22 CON6106 USB*1 connector (4-pin)
Table C-22 USB*1 connector (4-pin)
Pin No.
Signal Name
GND
USBP6-
I/O
-
Pin No.
Signal Name
USBP6+
+5VUSB6
I/O
I/O
-
1
3
2
4
I/O
C-16
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.23 CON6107 eSATA/USB Combo connector (11-pin)
Table C-23 Speaker connector (11-pin)
Pin No.
Signal Name
+5VUSB7
I/O
Pin No.
Signal Name
USBP7-_C
GND
I/O
I/O
-
1
3
-
I/O
-
2
4
USBP7+_C
GND
5
6
SATA_TXP3_C
GND
I
7
SATA_TXN3_C
SATA_RXN3_C
GND
I
8
-
9
O
-
10
SATA_RXP3_C
O
11
C.24 CON3701 LCD connector (40-pin)
Table C-24 LCD connector (40-pin)
Pin No.
1
Signal Name
AC_INV
I/O
-
-
I
Pin No.
2
Signal Name
AC_INV
I/O
-
-
3
AC_INV
4
NC
5
BACK_EN_C
NC
6
LCD_BL_PWM_C
GND
I
7
-
-
I
8
-
9
GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND
-
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
LVDS_CLKBP
GND
LVDS_CLKBM
LVDS_YB2P
GND
I
-
I
I
LVDS_YB2M
LVDS_YB1P
GND
-
I
LVDS_YB1M
LVDS_YB0P
GND
I
-
I
I
LVDS_YB0M
LVDS_CLKAP
GND
-
I
LVDS_CLKAM
LVDS_YA2P
GND
I
-
I
I
LVDS_YA2M
LVDS_YA1P
GND
-
I
LVDS_YA1M
LVDS_YA0P
LVDS_DDC_DATA
GND
I
-
I
I
LVDS_YA0M
LVDS_DDC_CLK
+3VS
I/O
-
I
-
-
+LCD_VCC
NC
-
+LCD_VCC
-
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.25 CON3801 RGB connector (15-pin)
Table C-25 RGB connector (15-pin)
Pin No.
Signal Name
RED
I/O
Pin No.
Signal Name
GREEN
I/O
1
3
I
I
2
4
I
BLUE
GND:
NC
-
5
-
-
-
-
I
6
GND
-
7
GND
8
GND
-
-
9
+5VS
10
12
14
GND
11
13
15
NC
DDC2BD_S
VSYNC
I/O
I
HSYNC
DDC2BC_S
I
C.26 CON5401 Newcard interface connector (26-pin)
Table C-26 Newcard interface connector (26-pin)
Pin No.
Signal Name
GND
I/O
Pin No.
Signal Name
USBP10-
CP_USB#
NC
I/O
1
3
-
2
4
I/O
USBP10+
NC
I/O
I
5
-
I
-
I
I
6
-
I/O
-
7
SCL_3V
8
SDA_3V
9
+1.5VS_PE
PCIE_WAKE#
PERST#
+3VS_PE
10
12
14
+1.5VS_PE
+3V_PE
11
13
-
+3VS_PE
-
NEWCARD_CLK
_REQ#
-
I
I
O
I
15
17
19
16
18
20
CLK_PCIE_NEW
CARD#
CP_PE#
CLK_PCIE_NEW
CARD
-
GND
PCIE_RXN4
GND
PCIE_RXP4
PCIE_TXN4
GND
O
-
O
I
21
23
25
22
24
26
PCIE_TXP4
I
-
C-18
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
C.27 J7701
DC-IN connector (4-pin)
Table C-27 DC-IN connector (4-pin)
Pin No.
Signal Name
I/O
Pin No.
Signal Name
GND
D_A/D_DOCK_IN
I/O
1
3
GND
-
-
2
4
-
-
D_A/D_DOCK_IN
C.28 CON7701 Battery connector (9-pin)
Table C-28 Battery connector (9-pin)
Pin No.
Signal Name
BAT_CON_F
NC
I/O
Pin No.
Signal Name
BAT_CON_F
GND
I/O
1
3
5
7
9
-
2
4
6
8
-
-
O
I
TS1#_C
SMB0_DAT_C
GND
I/O
-
SMB0_CLK_C
GND
-
C.29 CON4901 FAN connector (4-pin)
Table C-29
FAN connector (4-pin)
Pin No.
Signal Name
I/O
O
I
Pin No.
Signal Name
GND
I/O
1
3
FAN0_TACH
FAN_PWM
2
4
-
-
+5VS_FAN
C.30 CO6202 Camera Module connector (BTO) (6-pin)
Table C-30 Camera Module connector (6-pin)
Pin No.
Signal Name
MIC_INT_P
GND
I/O
I
Pin No.
Signal Name
MIC_INT_N
USBP3+
I/O
I
1
3
5
2
4
6
-
I/O
-
USBP3-
I/O
+5VS_Camera
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
C.31 CON6201 Touch Panel connector (BTO) (6-pin)
Table C-31
Touch Panel connector (6-pin)
Pin No.
Signal Name
I/O
Pin No.
Signal Name
GND
I/O
-
1
3
5
LID_SW#
USBP8+
I
I/O
I
2
4
6
USBP8-
I/O
-
TPN_RST#
+3VS_TPN
C.32 CO6204 Felica Module connector (BTO) (6-pin)
Table C-32
Felica Module connector (6-pin)
Pin No.
Signal Name
+5VS_FELICA
USBP11+
NC
I/O
-
Pin No.
Signal Name
USBP11-
GND
I/O
I/O
-
1
3
5
2
4
6
I/O
-
GND
-
C.33 CO6204 Buletooth connector (BTO) (8-pin)
Table C-33
Bluetooth connector (8-pin)
Pin No.
Signal Name
+3VS
I/O
Pin No.
Signal Name
I/O
I
1
3
5
7
-
I
2
4
6
8
BT_RST#
BT_CHDATA
GND
BT_ON/OFF#
BT_CHCLK
USBP11-
I/O
-
I
I/O
USBP11+
I/O
C-20
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Pin Assignments
Appendices
Touch PAD Board
C.34 M1TP_CON1 Touch PAD board to Touch PAD connector
(12-pin)
Table C-34
Touch PAD Board to Touch PAD connector (12-pin)
Pin No.
Signal Name
I/O
-
Pin No.
Signal Name
+5VS
I/O
1
3
5
+5VS
2
4
6
-
I
TP_DAT
GND
I/O
-
TP_CLK
GND
-
LightGuide_ON_
OFF
7
NC
-
8
-
9
NC
-
10
12
TP_LEFT#
NC
O
-
11
TP_RIGHT#
O
C.35 M1TP_J1 Touch PAD Board to Fingerprint connector
(6-pin)
Table C-35
Touch PAD Board to Fingerprint connector (6-pin)
Pin No.
Signal Name
F_+1.8VS_FP
T_GND
I/O
Pin No.
Signal Name
FP_USB_D-
FP_USB_D+
+3VS_FP
I/O
I/O
I/O
-
1
3
5
-
-
-
2
4
6
F_+3VS_FP
Satellite M500/M500/M507 Maintenance Manual [CONFIDENTIAL]
C-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix C Pin Assignments
LAN Board
C.36 MLCON301 LAN/RJ11(BTO) interface connector (14-pin)
Table C-36 LAN/RJ11 interface connector (14-pin)
Pin No.
Signal Name
L_TXP_M
I/O
I/O
I/O
I/O
I/O
-
Pin No.
Signal Name
L_TXN_M
I/O
I/O
I/O
I/O
I/O
I
1
3
2
4
L_RXP_M
L_TRLP2_M
L_RXN_M
5
L_TRLM2_M
L_TRLP3_M
+3VSUS_L_M
+3VSUS_L_M
RING_J_M
6
7
8
L_TRLM3_M
LED_1000#_M
LED_100#_M
TIP_J_M
9
10
12
10
11
13
-
I
I/O
I/O
C.37 MLCON103 USB*2 connector (8-pin)
Table C-37 USB*2 connector (8-pin)
Pin No.
Signal Name
+5VUSB1_M
USBP1+_M
I/O
-
Pin No.
Signal Name
USBP1-_M
LGND
I/O
I/O
-
1
3
5
7
2
4
6
8
I/O
-
+5VUSB0_M
USBP0+_M
USBP0-_M
LGND
I/O
-
I/O
C.38 MLCON302 Modem connector(BTO) (2-pin)
Table C-38 Modem connector (2-pin)
Pin No.
Signal Name
RING_M
I/O
Pin No.
Signal Name
TIP_M
I/O
I/O
I/O
1
2
C-22
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D Keyboard Scan/Character Codes
Appendices
Appendix D Keyboard Scan/Character Codes
Table D-1 Scan codes (set 1 and set 2) (1/4)
Code set 1
Make Break
Code set 2
Break
Cap
No.
Keytop
Note
Make
01
02
03
04
05
06
07
08
09
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
‘ ~
1 !
2 @
3 #
4 $
5 %
6 ^
7 &
8 *
9 (
0 )
- _
= +
BkSp
Tab
Q
29
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
A9
82
83
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
0E
16
1E
26
25
2E
36
3D
3E
46
45
4E
55
66
0D
15
1D
24
2D
2C
35
3C
43
44
4D
54
5B
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
0E
16
1E
26
25
2E
36
3D
3E
46
45
4E
55
66
0D
15
1D
24
2D
2C
35
3C
43
44
4D
54
5B
*1
*1
*1
*1
W
E
R
T
Y
U
*1
*1
*1
*1
I
O
P
[ {
] }
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix D Keyboard Scan/Character Codes
Table D-1 Scan codes (set 1 and set 2) (2/4)
Code set 1
Code set 2
Break
Cap
Keytop
Note
No.
Make
Break
Make
29
30
31
32
33
34
35
36
37
38
39
40
41
\ ¦
2B
3A
1E
1F
20
21
22
23
24
25
26
27
28
AB
BA
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
5D
58
1C
1B
23
2B
34
33
3B
42
4B
4C
52
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
5D
58
1C
1B
23
2B
34
33
3B
42
4B
4C
52
*2
Caps Lock
A
S
D
F
G
H
J
*1
*1
*1
*1
K
L
; :
‘ “
43
44
45
Enter
1C
2A
56
9C
AA
D6
5A
12
61
F0
F0
F0
5A
12
61
Shift (L)
No.102
key
46
47
48
49
50
51
52
53
54
55
Z
X
2C
2D
2E
2F
30
31
32
33
34
35
AC
AD
AE
AF
B0
B1
B2
B3
B4
B5
1A
22
21
2A
32
31
3A
41
49
4A
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
1A
22
21
2A
32
31
3A
41
49
4A
C
V
B
N
M
*1
, <
. >
/ ?
*1
*1
57
Shift (R)
36
B6
59
F0
59
D-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D Keyboard Scan/Character Codes
Appendices
Table D-1 Scan codes (set 1 and set 2) (3/4)
Code set 1
Code set 2
Break
Cap
No.
Keytop
Note
Make
Break
Make
58
60
Ctrl (L)
Alt (L)
Space
ALT (R)
Ins
1D
38
9D
B8
B9
14
11
29
F0
F0
F0
14
11
29
11
70
71
6B
6C
69
75
72
7D
7A
74
76
05
06
04
0C
03
0B
83
0A
01
09
61
39
62
E0 38
E0 52
E0 53
E0 B8 E0 11
E0 D2 E0 70
E0 D3 E0 71
E0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
75
E0
E0
*4
*4
*4
*4
*4
*4
*4
*4
*4
*4
76
Del
79
E0 4B E0 CB E0 6B E0
80
Home
End
E0 47
E0 4F
E0 48
E0 50
E0 49
E0 51
E0 C7 E0 6C E0
81
E0 CF E0 69
E0 C8 E0 75
E0 D0 E0 72
E0
E0
E0
83
84
85
PgUp
PgDn
E0 C9 E0 7D E0
E0 D1 E0 7A E0
86
89
E0 4D E0 CD E0 74
E0
F0
110
112
113
114
115
116
117
118
119
120
121
Esc
F1
01
3B
3C
3D
3E
3F
40
41
42
43
44
81
BB
BC
BD
BE
BF
C0
C1
C2
C3
C4
76
05
06
04
0C
03
0B
83
0A
01
09
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F2
F3
F4
F5
F6
F7
F8
F9
F10
*3
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix D Keyboard Scan/Character Codes
Table D-1 Scan codes (set 1 and set 2) (4/4)
Cap
No.
Code set 1
Make Break
Code set 2
Break
Keytop
Note
Make
78
07
122
123
124
126
202
203
204
F11
F12
57
58
D7
D8
F0
F0
78
07
*3
*3
PrintSc
Pause
Fn
Refer to table 2-25
Refer to table 2-25
*5
Win
E0
E0
5B E0 DB E0
5D E0 DD E0
1F E0
2F E0
F0
F0
1F
2F
App
Notes:
1. * Scan codes differ by overlay function.
2. * This key corresponds to key No. 42 in the 102 key mode.
3. * Combination with the Fn key makes different codes.
4. * Scan codes differ by mode.
5. * The Fn key does not generate a code by itself..
D-4
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D Keyboard Scan/Character Codes
Appendices
Table D-2 Scan codes with left Shift key
Cap Key
Code set 1
Make Break
E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12
Code set 2
No.
top
Make
Break
55
75
76
79
/
INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12
DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 E0 71 E0 F0 71 E0 12
E0 AA E0 4B E0 CB E0 2A E0 F0 12 E0 6B E0 F0 6B E0 12
80 Home E0 AA E0 47 E0 C7 E0 2A E0 F0 12 E0 6C E0 F0 6C E0 12
81
83
84
End E0 AA E0 4F E0 CF E0 2A E0 F0 12 E0 69 E0 F0 69 E0 12
E0 AA E0 48 E0 C8 E0 2A E0 F0 12 E0 75 E0 F0 75 E0 12
E0 AA E0 50 E0 D0 E0 2A E0 F0 12 E0 72 E0 F0 72 E0 12
85 PgUp E0 AA E0 49 E0 C9 E0 2A E0 F0 12 E0 7D E0 F0 7D E0 12
86 PgDn E0 AA E0 51 E0 D1 E0 2A E0 F0 12 E0 7A E0 F0 7A E0 12
89
E0 AA E0 4D E0 CD E0 2A E0 F0 12 E0 74 E0 F0 74 E0 12
Note : The table above shows scan codes with the left Shift key.
In combination with the right Shift key, scan codes are changed as listed below:
With left Shift
With right Shift
Set 1
Set 2
E0 AA __________ E0 B6
E0 2A ___________ E0 36
E0 F0 12 ________ E0 F0 59
E0 12 ___________ E0 59
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix D Keyboard Scan/Character Codes
Table D-3 Scan codes in Numlock mode
Cap
No.
Key
Code set 1
Code set 2
Break
top
Make
Break
Make
75
76
79
80
81
83
84
85
86
89
INS
DEL
E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12
E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12
E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B E0 F0 6B E0 F0 12
Home E0 2A E0 47 E0 C7 E0 AA E0 12 E0 6C E0 F0 6C E0 F0 12
End
E0 2A E0 4F E0 CF E0 AA E0 12 E0 69 E0 F0 69 E0 F0 12
E0 2A E0 48 E0 C8 E0 AA E0 12 E0 75 E0 F0 75 E0 F0 12
E0 2A E0 50 E0 D0 E0 AA E0 12 E0 72 E0 F0 72 E0 F0 12
PgUp E0 2A E0 49 E0 C9 E0 AA E0 12 E0 7D E0 F0 7D E0 F0 12
PgDn E0 2A E0 51 E0 D1 E0 AA E0 12 E0 7A E0 F0 7A E0 F0 12
E0 2A E0 4D E0 CD E0 AA E0 12 E0 74 E0 F0 74 E0 F0 12
Table D-4 Scan codes with Fn key
Cap
Key
top
Code set 1
Code set 2
Break
No.
Make
Break
C5
Make
77
121
122
123
NUMERIC
ARROW
Scrl
45
45
46
F0
F0
F0
77
77
7E
C5
77
C6
7E
D-6
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D Keyboard Scan/Character Codes
Appendices
Table D-5 Scan codes in overlay mode
Code set 1
Break
Code set 2
Break
Cap
No.
Keytop
(7)
Make
Make
08
09
10
11
23
24
25
26
37
38
39
40
52
54
55
7
8
9
0
U
I
47
48
49
C7
C8
C9
6C
75
7D
F0
F0
F0
6C
75
7D
4A
6B
73
74
7C
69
72
7A
7B
70
71
79
(8)
(9)
(/)
E0
35
E0
B5
E0
4A
E0
F0
(4)
(5)
(6)
(*)
(1)
(2)
(3)
(-)
4B
4C
4D
37
4F
50
51
4A
52
53
4E
CB
CC
CD
B7
CF
D0
D1
CA
D2
D3
CE
6B
73
74
7C
69
72
7A
7B
70
71
79
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
O
P
J
K
L
;
M
.
(0)
(.)
/
(+)
Table D-6 No.124 key scan code
Key
top
Code set 1
Code set 2
Shift
Make
Break
Make
Break
Prt Sc Common E0 2A E0 37 E0 B7 E0 AA E0 12 E0 7C E0 F0 7C E0 F0 12
E0 37
E0 37
54
E0 B7
E0 B7
D4
E0 7C
E0 7C
84
E0 F0 7C
E0 F0 7C
F0 84
Ctrl
Shift
Alt
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
D-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix D Keyboard Scan/Character Codes
Table D-7 No.126 key scan code
Key
top
Shift
Code set 1
Make
Code set 2
Make
Pause Common E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14
*
F0 77
Ctrl*
E0 46 E0 C6
E0 7E E0 F0 7E
*: This key generates only make codes.
D-8
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E Key Layout
Appendices
Appendix E
Appendix E Key Layout
E.1 United Kingdom (UK) Keyboard
Figure E-1 UK keyboard
E.2 United States (US) Keyboard
Figure E-2 US keyboard
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
Appendix E Key Layout
E.3 Japanese (JP) Keyboard
Figure E-3 JP keyboard
E-2
[CONFIDENTIAL] Satellite M500/M505/M507 Maintenance Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F BIOS rewrite procedures
Appendices
Appendix G
Appendix F BIOS rewrite procedures
This Appendix explains how to rewrite the system BIOS program when you update the
system BIOS.
Tools
To rewrite the BIOS, you need the following tool:
Bootable USB key for the computer that has renewed BIOS data.
Rewriting the BIOS
1. Set the system to boot mode.
2. Turn off the power to the computer.
3. Remove the external cable and PC card, connect the USB key which has the latest
BIOS document to t he system.
4. Turn on the power with Esc key pressing down, and choose boot from USB device.
5. Enter to the BIOS document and execute the “UBIOS.bat”.
6. The BIOS rewriting starts.
7. When the process is completed, the system automatically shutdown.
NOTE: 1. Connect the AC adapter to the computer when you rewrite the BIOS.
2. Do not turn off the power while you are rewriting the BIOS. If the rewrite
fails, it might be impossible to start up the computer.
3
If you fail to rewrite BIOS, then when you next turn on the power, a message
may be displayed that the contents of the BIOS have been erased. In this
case, insert the BIOS rewriting disk and the BIOS will be rewritten.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
G-
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix G EC/KBC rewrite procedures
Appendices
Appendix H
Appendix G EC/KBC rewrite procedures
This Appendix explains how to rewrite the EC/KBC system program when you update the
EC/KBC system.
Tools
To rewrite the EC/KBC, you need the following tool:
Bootable USB key for the computer that has renewed BIOS data.
Rewriting the EC/KBC
NOTE: 1. Rewrite the EC/KBC only when instructed by a diagnostic disk release
notice.
2. Connect the AC adaptor to the computer when you rewrite the EC/KBC.
3. Do not turn off the power while you are rewriting the EC/KBC.
If the rewrite fails, it might be impossible to start up the computer.
4. If you fail to rewrite EC/KBC, then when you next turn on the power, a
message may be displayed that the contents of the EC/KBC have been
erased. In this case, insert the BIOS/EC/KBC rewriting disk and the
EC/KBC will be rewritten.
5. Normally it takes about 30 seconds to rewrite the EC/KBC. It may take 3
minutes (maximum), depending on the conditions of the computer or ICs.
The computer is not hung up. Allow sufficient time. Never reboot or turn off
the power to the computer before the rewriting is completed.
1. Set the system to boot mode.
2. Turn off the power to the computer.
3. Remove the external cable and PC card, connect the USB key which has the latest
BIOS document to t he system.
4. Turn on the power with Esc key pressing down, and choose boot from USB device.
5. Enter to the BIOS document and execute the “UBIOS.bat”.
6. The BIOS rewriting starts.
7. When the process is completed, the system automatically shutdown.
Satellite M500/M505/M507 Maintenance Manual [CONFIDENTIAL]
G-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Thermo Products Furnace ome 72d36 User Manual
Tokina Camera Accessories TM10Z0818GAI User Manual
Toshiba Marine Radio C650 User Manual
Trane Air Conditioner 3RT PRC005 EN User Manual
Uniden Portable Radio uh049sx 2 User Manual
Vermont Casting Indoor Fireplace DV580 DV360 User Manual
Vizio Car Satellite TV System M492i B2 User Manual
Vizio TV Video Accessories ISGB03 User Manual
VocoPro Microphone VHF 77 User Manual
VTech Cordless Telephone T2447 User Manual