Direct Vent Gas Fireplace
Models: DV360, DV580
INSTALLER / CONSUMER
SAFETY INFORMATION
PLEASE READ THIS MANUAL
BEFORE INSTALLING AND USING
APPLIANCE
WARNING!
IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR
EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF
LIFE.
FOR OUR SAFETY
Homeowner’s Installation and
Operating Manual
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
WHAT TO DO IF YOU SMELL GAS:
•
•
Do not try to light any appliance.
Do not touch any electric switch; do not
sue any phone in your building.
Immediately call your gas supplier from
your neighbor’s phone. Follow the gas
supplier’s instructions.
•
•
CERTIFIED
I
If you cannot reach your gas supplier, call
the fire department.
DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS
OR ANY OTHER APPLIANCE.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
20010667 12/06 Rev. 5
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Installation & Operating Instructions
This gas appliance should be installed by a qualified installer in
accordance with local building codes and with current CSA-
B149.1 Installation codes for Gas Burning Appliances and
Equipment. If the unit is being installed in a mobile home, the
installation should comply with the current CAN/CSA Z 240.4
code. For U.S.A Installations follow local codes and/or the cur-
rent National Fuel Gas Code. ANSI Z223.1/NFPA 54.
WARNING: Check with your electronics manufac-
turer before installing a television or other electronic
device above this fireplace.
This appliance may be installed in an aftermarket
permanently located, manufactured home or mobile
home, where not prohibited by local codes.
In the Commonwealth of Massachusetts, all gas fittings and
installation of this appliance shall be done by a licensed
gas fitter or licensed plumber.
This appliance is only for use with the type of gas
indi-cated on the rating plate. This appliance is not
convertible for use with other gases, unless a certi-
fied kit is used.
FOR SAFE INSTALLATION AND OPERATION PLEASE
NOTE THE FOLLOWING:
1 . This fireplace gives off high temperatures and should be
located out of high traffic areas and away from furniture and
draperies.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this fireplace and should stay
away to avoid burns or ignition of clothing.
IMPORTANT:
PLEASE READ THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the
fireplace ON.
It is normal for fireplaces fabricated of steel to give off
some expansion and/or contraction noises during the
start up or cool down cycle. Similar noises are found
with your furnace heat exchanger or car engine. It is
not unusual for your CFM Corporation gas fireplace to
give off some odor the first time it is burned. This is due
to the manufacturing process.
3. Children should be carefully supervised when in the same
room as your fireplace.
4. Under no circumstances should this fireplace be modified.
Parts removed for servicing should be replaced prior to
operating this fireplace again.
5. Installation and any repairs to this fireplace must be per-
formed by a qualified installer, service agency or gas sup-
plier. A professional service person should be contacted to
inspect this fireplace annually. Make it a practice to have
all of your gas fireplaces checked annually. More frequent
cleaning may be required due to excess lint and dust from
carpeting, bedding material, etc.
6. Control compartments, burners and air passages in this fire-
place should be kept clean and free of dust and lint. Make
sure the gas valve and pilot light are turned off before you
attempt to clean this fireplace.
Please ensure that your room is well ventilated
-open all windows.
It is recommended that you burn your fireplace for at
least ten (10) hours the first time you use it. If the op-
tional fan kit has been installed, place the fan switch in
the “OFF” position during this time.
7. The venting system (chimney) of this fireplace should be
checked at least once a year and if needed your venting
system should be cleaned.
Locating Your Fireplace
8. Keep the area around your fireplace clear of combustible
materials, gasoline and other flammable vapor and liquids.
This fireplace should not be used as a drying rack for cloth-
ing, nor should Christmas stocking or decorations be hung in
the area of it.
E
A
B
Y
X
C
9. Under no circumstances should any solid fuels (wood, coal,
paper or cardboard etc.) be used in this fireplace.
10.The flow of combustion and ventilation air must not be ob-
structed in any way.
D
Y
B
11. When fireplace is installed directly on carpeting, vinyl tile
or any combustible material other than wood, this fireplace
must be installed on a metal or wood panel extending the full
width and depth of the fireplace.
F
LU584-1
12.This fireplace requires adequate ventilation and combustion
air to operate properly.
13.This fireplace must not be connected to a chimney flue serv-
ing a separate solid fuel burning fireplace.
Fig. 1 Locating gas fireplace.
A) Flat on wall
B) Cross corner
C) **Island
Chase installation
D) *Room divider E) *Flat on wall corner F)
Y) 6” minimum
Note (Fig. 1):
14.When the fireplace is not in use it is recommended that the
gas valve be left in the OFF position.
** Island (C) and Room Divider (D) installation is possible as long as
the horizontal portion of the vent system (X) does not exceed 20’ (6 m).
See details in Venting Section.
* When you install your fireplace in(D) Room divider or (E) Flat on wall
corner positions (Y), a minimum of 6“ (152 mm) clearance must be
maintained from the perpendicular wall and the front of the fireplace.
Proposition 65 Warning: Fuels used in gas, woodburning or
oil fired appliances, and the products of combustion of such
fuels, contain chemicals known to the State of California to
cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6
20010667
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Fireplace Dimensions (Installed as Top Vent)
Rough
Opening
Depth
J
P
V
I
T
Q
H
K Recessed
Nailing Flange
K
S - Rough Opening Width
W
V
Rough
Opening
Height
U
B
G
F
R
D
C
A
Electrical
Access
Gas Line
Access
E
L
N
M
O
G
Fig. 2 Fireplace specifications and framing dimensions.
Ref.
A
B
C
D
E
DV360
(1041 mm)
DV580
41”
37”
36”
24¹⁄₂”
7”
47”
41¹⁄₄”
42”
28¹⁄₂”
7”
(1194 mm)
(1048 mm)
(1067 mm)
(724 mm)
(178 mm)
(152 mm)
(32 mm)
(591 mm)
(140 mm)
(787 mm)
(16 mm)
(940 mm)
(914 mm)
(622 mm)
(178 mm)
(152 mm)
(32 mm)
(489 mm)
(140 mm)
(635 mm)
(16 mm)
(273 mm)
(51 mm)
(194 mm)
(48 mm)
(178 mm) Dia.
(102 mm) Dia.
Framing Dimensions
(978 mm)
(1048 mm)
(489 mm)
(1581 mm)
(1118 mm)
(807 mm)
F
6”
6”
G
H
I
J
K
1¹⁄₄”
19¹⁄₄”
5¹⁄₂”
25”
5/8”
10³⁄₄”
2”
7⁵⁄₈”
1⁷⁄₈”
7”
1¹⁄₄”
23¹⁄₂”
5¹⁄₂”
31”
5/8”
10³⁄₄”
2”
L
(273 mm)
(51 mm)
M
N
O
P
11¹⁄₄”
1⁷⁄₈”
7”
(286 mm)
(48 mm)
(178 mm) Dia.
(102 mm) Dia.
Q
4”
4”
R
S
T
U
V
W
38¹⁄₂”
41¹⁄₄”
19¹⁄₄”
62¹⁄₄”
44”
42¹⁄₂”
47¹⁄₄”
23¹⁄₂”
75”
53”
38”
(1080 mm)
(1200 mm)
(597 mm)
(1905 mm)
(1346 mm)
(965 mm)
31³⁄₄”
20010667
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Fireplace Dimensions (Installed as Rear Vent)
Rough
Opening
Depth
I
U
S
H
J
Recessed
Nailing Flange
J
R - Rough Opening Width
V
U
Rough
Opening
Height
T
G
F
P
Q
B
D
C
A
Electrical
Access
O
N
Gas Line
Access
E
K
M
L
G
Fig. 3 Fireplace specifications and framing dimensions.
Ref.
A
B
C
D
E
F
G
H
I
DV360
(1041 mm)
DV580
41”
37”
36”
24¹⁄₂”
7”
6”
1¹⁄₄”
19¹⁄₄”
25”
5/8”
10³⁄₄”
2”
47”
41¹⁄₄”
42”
28¹⁄₂”
7”
(1194 mm)
(1048 mm)
(1067 mm)
(724 mm)
(178 mm)
(152 mm)
(32 mm)
(591 mm)
(787 mm)
(16 mm)
(940 mm)
(914 mm)
(622 mm)
(178 mm)
(152 mm)
(32 mm)
(489 mm)
(635 mm)
(16 mm)
6”
1¹⁄₄”
23¹⁄₂”
31”
5/8”
10³⁄₄”
2”
J
K
L
(273 mm)
(51 mm)
(273 mm)
(51 mm)
M
N
O
P
7⁵⁄₈”
1⁷⁄₈”
(194 mm)
(48 mm)
11¹⁄₄”
1⁷⁄₈”
35³⁄₄”
(286 mm)
(48 mm)
(908 mm)
31¹³⁄₁₆” (808 mm)
32⁹⁄₁₆” (827 mm)
36⁹⁄₁₆” (928 mm)
Framing Dimensions
(978 mm)
Q
R
S
T
U
V
38¹⁄₂”
41¹⁄₄”
19¹⁄₄”
62¹⁄₄”
44”
42¹⁄₂”
47¹⁄₄”
23¹⁄₂”
75”
53”
38”
(1080 mm)
(1200 mm)
(597 mm)
(1905 mm)
(1346 mm)
(965 mm)
(1048 mm)
(489 mm)
(1581 mm)
(1118 mm)
(807 mm)
31³⁄₄”
20010667
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Clearance to Combustibles
Top of unit to ceiling................................. 36” (914 mm)
Front of unit to combustibles ................... 36” (914 mm)
Appliance
Top of standoff ....................................... 0” (0 mm)
Bottom..................................................... 0” (0 mm)
Side......................................................... 0” (0 mm)
Back........................................................ 0” (0 mm)
Venting
J
I
H
Black
G
Surround
Face
F
Concentric sections of DV Vent................... 1” (25 mm)
Nonconcentric sections of DV Vent
Mantel
Leg
CFM164a
Sides and bottom.................................. 1” (25 mm)
Top ........................................................ 2” (51 mm)
K
L
Side of
Combustion Chamber
M
N
Mantels
O
The height that a combustible mantel is fitted above the
fireplace is dependent on the depth of the mantel. This
also applies to the distance between the mantel leg (if
fitted) and the fireplace.
For the correct mounting height and widths, refer to
Figures 4a, 4b and the Mantel Chart below.
The distances and reference points are not affected by
the fitting of a bay window front trim kit.
Noncombustible mantels and legs may be installed at
any height and width around the appliance. When using
paint or lacquer, it must be heat resistant to prevent
CFM170
discoloration.
Mantel
Mantel Leg from Side
of Comb. Opening
11¹⁄₂” (292 mm)
9¹⁄₂” (241 mm)
7¹⁄₂” (191 mm)
5¹⁄₂” (140 mm)
3¹⁄₂” (89 mm)
V
Ref.
Leg Depth
10” (254 mm)
8” (203 mm)
6” (152 mm)
4” (101 mm)
2” (51 mm)
Ref.
K
L
M
N
O
W
F
G
H
I
X
Y
Z
J
Fig. 4b Combustible mantel leg minimum installation.
Maintain minimum
3/4” (19 mm) clear-
ance to combustibles
A
B
C
D
E
Hearth
Fireplace
A hearth is not mandatory, but is recommended for
aesthetic purposes. We recommend a noncombustible
hearth which projects out 12” (305 mm) or more from
the front of the fireplace.
Louvre Assembly
top
Top of Combustion
Chamber
Cold climate installation recommendation:
When installing this unit against a non-in-
sulated exterior wall or chase, it is manda-
tory that the outer walls be insulated to
conform to applicable insulation codes.
Bottom of Door Trim
CFM146
Mantel Chart
Mantel Shelf
Ref. or Breast Plate
Depth
Mantel from Top
Ref. of Comb. Chamber
V
W
X
Y
Z
10” (254 mm)
8” (203 mm)
6” (152 mm)
4” (101 mm)
2” (51 mm)
A
B
C
D
E
19” (483 mm)
17” (432 mm)
15” (381 mm)
13” (330 mm)
11” (279 mm)
Fig. 4a Combustible mantel minimum installation.
20010667
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
C
Framing And Finishing
Adjustable Drywall Strip
(Nailing Flange)
A
Check fireplace to make sure it is levelled
and properly positioned.
B
Flange
Position
Drywall
Depth
To mount the appliance: Choose the location.
A
B
C
1/2” / 13 mm
5/8” / 16 mm
3/4” / 19 mm
DV360 (Fig. 5)
1. This unit comes with four (4) flanges pre-mounted
on both sides of the fireplace to allow two different
drywall thicknesses to be used. Flange “A” is for 1/2”
drywall while flange “B“ is for 5/8” drywall.
2. Bend the desired flanges out 90° on both sides of
the fireplace. Slide the fireplace into the framed
opening until the flanges contact the front surfaces
of the framing. Level the unit and secure it firmly in
place.
Flange Location for
Desired Drywall Depth
Flange
Position
Drywall
Depth
1/2” / 13 mm
5/8” / 16 mm
Adjustable
1/2”, 5/8” & 3/4”
Spacing
A
B
FP1023
Fig. 5a Adjustable drywall strip (nailing flange) for DV580.
DV360 / DV580
Certified To
ANSI Z21.88-2005 / CSA 2.33-2005
Vented Gas Fireplace Heater
B
A
For units:
GFDN4L2, GFDE4L2, GFDI4L2, GFDL4L2
GFDN4P0, GFDE4P0, GFDI4P0
Gas Specifications
FP1539
MAX.
INPUT INPUT
B.T.U.H B.T.U.H.
MIN.
Fig. 5 Drywall flange location for DV360.
GAS
CONTROL
MODEL
DV360RN
DV360RP
DV360EN
DV360EP
FUEL
DV580 (Fig. 5a)
Natural Gas Millivolt Hi/Lo
30,000 18,500
30,000 17,000
30,000 18,500
30,000 20,000
1. Nailing flanges are supplied with the fireplace (found
on the fireplace hearth). To level the box and secure
it firmly in place, remove the nailing flanges from
the hearth and install at the sides of the fireplace as
shown in Figure 5a.
Propane
Natural Gas
Propane
Millivolt Hi/Lo
24 Volt Hi/Lo
24 Volt Hi/Lo
DV360RFN Natural Gas Comfort Control 30,000 20,000
DV360RFP
DV580RN
DV580RP
Propane
Comfort Control 30,000 21,000
2. Screw through the slotted holes in the drywall strip
and into pre-drilled holes in fireplace side. Measure
from face of fireplace to the face of the drywall strip
to confirm the final depth.
Natural Gas Millivolt Hi/Lo
38,000 26,500
38,000 27,000
Propane
Millivolt Hi/Lo
DV580EN
DV580EP
Natural Gas
Propane
24 Volt Hi/Lo
24 Volt Hi/Lo
38,000 26,500
38,000 27,000
DV580RFN Natural Gas Comfort Control 38,000 26,500
DV580RFP Propane Comfort Control 38,000 27,000
Final Finishing
Noncombustible materials such as brick or tile can be
extended over the edges of the face of the fireplace.
Do not cover the window frame assembly, any vent,
louvre assembly top or louvre assembly bottom. If
a Trim Kit is to be installed, brick and tile will have to be
installed flush with the side of this appliance.
Gas Inlet and Manifold Pressures
Natural LP (Propane)
Minimum Inlet Pressure
Maximum Inlet Pressure
Manifold Pressure
5.5” w.c.
14.0” w.c.
3.5” w.c.
11.0” w.c.
14.0” w.c.
10.0” w.c.
20010667
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
The gas control is equipped with a captured screw type
pressure test point, therefore it is not necessary to pro-
vide a 1/8” test point up stream of the control.
High Elevations
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to
4,500 feet (1,370m) above sea level.
When using copper or flex connector use only approved
fittings. Always provide a union when using black iron
pipe so that the gas line can be easily disconnected for
burner or fan servicing. (Fig. 6) See the gas specifica-
tions for pressure details and ratings.
For elevations above 4,500 feet (1,370m) in USA,
installations must be in accordance with the
current ANSI Z223.1/NFPA 54 and/or local codes
having jurisdiction.
Remote ON/OFF Switch Installation
In Canada, please consult provincial and/or local
authorities having jurisdiction for installations at
elevations above 4,500 feet (1,370m).
Do not wire the remote ON/OFF wall switch for this gas
appliance into a 120v power supply.
1. Thread wire through the electrical knockout located
on either side of the unit. Take care not to cut the
wire or insulation on metal edges. Ensure the wire is
secured and protected from possible damage. Run
one end of the gas control valve and the other end to
the conveniently located wall switch.
Gas Line Installation
When purging gas line the front glass
must be removed.
The gas pipeline can be brought in through the right
side of the appliance. Knockouts are provided at conve-
nient locations to allow for the gas pipe installation and
testing of any gas connection.
2. Attach the wire to the ON/OFF switch and install
switch into receptacle box. Attach cover plate to
switch.
3. Connect wiring to gas valve. (Fig. 7)
The gas line connection can be made with properly
tinned 3/8” copper tubing, 1/2” rigid pipe or an approved
flex connector. Since some municipalities have addi-
tional local codes, it is always best to consult your local
authority and the CSA-B149.1 installation codes.
Remote ON/OFF
Switch
For USA installations consult the current National Fuel
Gas Code, ANSI Z223.1/NFPA 54.
1/2” Gas Supply
1/2” NPT x 3/8” Flare Shut-
off Valve
FP1218
Fig. 7 Remote switch wiring diagram for R models.
3/8” Flex Line
(from valve)
Alternate Switch Location
The remote switch can be installed on either side of
the access door. Mount the switch to the switch bracket
provided. Screw the bracket on either side of the frame,
line up the screws with the prepunched holes. (Fig. 8)
FP297a
Fig. 6 Typical gas supply installation.
Always check for gas leaks with a mild
soap and water solution applied with a
brush no larger than 1” (25 mm). Never
apply soap and water solution with a spray
bottle. Do not use an open flame for leak
testing.
The fireplace valve must not be subjected
to any test pressures exceeding 1/2 psi.
Isolate or disconnect this or any other gas
appliance control from the gas line when
pressure testing.
FP1024
Fig. 8 Alternate switch location.
20010667
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
INSIDE
EB-1 Electrical Box
Electrical Box
The fireplace, when installed, must be
electrically connected and grounded in
accordance with local codes or, in the ab-
sence of local codes, with the current CSA
C22.1 Canadian Electrical Code.
FRONT
OF UNIT
OUTSIDE
For USA installations, follow the local
codes and the national Electrical Code
ANSI/NFPA No. 70.
OF UNIT
It is strongly suggested that the wiring of
the EB-1 Electrical Junction Box be carried
out by a licensed electrician.
FP580
FRONT
Fig. 9 EB-1 receptacle.
Electronic Gas Control Valve
Ensure that the power to the supply line
has been disconnected before commenc-
ing this procedure.
This appliance may be fitted with a Synetek ignition
module.
The EB-1 electrical junction box has been
supplied standard on the DV360/580 models to allow
for the easy installation of an optional fan kit.
Installation of the remote on/off starter switch or
wall thermostat on electronic ignition units.
1. Thread the wiring through the holes on the side
panels of the appliance. Take care not to cut the wire
or insulation on metal edges. Route the wire to a
conveniently located receptacle box.
To connect the EB-1 box to the house electrical supply,
follow the steps below.
1. Unscrew the retaining screw from the EB-1 base
plate (Fig. 9) and remove the EB-1 assembly from
the fireplace.
2. Remove the front cover of the EB-1 box.
3. Remove the plug socket
2. Attach the wire to the ON/OFF switch and install the
switch into the receptacle box.
assembly from the EB-1
box.
BLACK
WHITE
L1
L2
4. Feed the supply line in
from the outside through
the cable clamp. (Fig. 9)
5. Connect black wire of
the power supply line to
the brass screw (polar-
ized) of the socket as-
sembly.
POWER CORD
GREEN
PURPLE
PILOT SENSING
PILOT IGNITER
YELLOW
6. Connect the white wire
of the power line to the
chrome screw of the
socket assembly.
P
M
O
O
7. Connect the ground
wire of the supply line to
the green screw of the
socket assembly.
VALVE
CIRCUIT BOARD
BLUE
8. Refit the socket assem-
bly back into the electri-
cal box and replace the
cover plate. Secure the
cable with the clamp on
the outside of the unit
to prevent strain on the
connections.
ORANGE
RED
WHITE
ON/OFF SWITCH
OR
WALL THERMOSTAT
FP1571
Fig. 10 SIT822 Valve with Synetek electronic control wiring diagram.
9. The EB-1 electrical junction box is now ready to sup-
ply power to the FK12 or FK24 fan kits if fitted.
20010667
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
CAUTION: Remove insulation. Insulation extends
beyond opening in top of unit. Be sure to
remove all insulation before completing
conversion. Insulation measures 9¹⁄₄” x
22³⁄₄” (23.5 cm x 57.8 cm). If the unit is con-
verted back to a rear vent, the insulation
(Part number 20003129) must be replaced.
Optional Top Vent Application
The DV360/580 fireplace is shipped as a rear vent unit.
If the layout requires a top vent, convert the unit follow-
ing the steps below.
1. Remove the 10 screws securing outer collar adapter
to fireplace. (Fig. 11)
2. Set outer collar adapter aside.
3. Remove insulation from top of unit and discard. Re-
move the four (4) screws securing flue cover to top
of unit and remove flue cover. (Fig. 12)
Flue Pipe
4. Remove the four (4) screws securing flue pipe to
back of unit. Remove flue pipe. (Fig. 12)
Replace
Screws (4)
5. Secure flue cover to back of flue outlet. Be sure to
replace gasket. (Fig. 14)
6. Install flue pipe and gasket removed in step 4 to top
of unit with four (4) screws. Be sure to replace gas-
ket. (Fig. 14)
Replace
Screws
(4)
7. Secure outer collar adapter to unit with the round
collar on top, secure with 10 screws.
NOTE: Be sure not to damage any gasket material.
Flue Cover
FP1028
Fig. 13 Replace flue cover and flue pipe.
Outer
Collar
Adapter
Flue
Pipe
Remove
Screws
(5)
Remove Screws
(5)
FP1030
Fig. 11 Remove screws from outer collar adapter.
Insulation
FP1031
Flue
Cover
Fig. 14 Complete conversion.
Flue
Pipe
After conversion to top vent configuration,
the 4” (102 mm) flue pipe should be con-
centric within the 7” (175 mm) outer collar.
Remove
Screws
(4)
Remove Screws (4)
FP1027
Fig. 12 Remove flue cover and flue pipe.
20010667
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
General Venting
There must not be any obstruction such as bushes, gar-
den sheds, fences, decks or utility buildings within 24”
(610 mm) from the front of the termination hood.
Do not locate termination hood where excessive snow
or ice build up may occur. Be sure to check vent termi-
nation area after snow falls, and clear to prevent ac-
cidental blockage of venting system. When using snow
blowers, make sure snow is not directed towards vent
termination area.
Your fireplace is approved to be vented either through
the side wall, or vertical through the roof.
•
Only CFM Corporation venting components spe-
cifically approved and labelled for this fireplace
may be used.
•
•
Venting terminals shall not be recessed into a wall or
siding.
Horizontal venting which incorporates the twist lock
pipe must be installed on a level plane without an
inclining or declining slope.
Location of Vent Termination
•
Horizontal venting which incorporates the use of flex
venting shall have an inclining slope from the unit of
1” (25 mm) per 24” (610 mm).
It is imperative the vent termination be located observ-
ing the minimum clearances as shown on following
page.
20010667
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
General Venting Information - Termination Location
INSIDE
CORNER DETAIL
G
V
N
H
N
A
D
E
B
V
L
C
B
B
�����
������
V
V
B
V
V
Fixed
Operable
Operable
Closed
F
B
M
V
J
X
B
I
K
X
V
A
CFM145a
AREA WHERE TERMINAL IS NOT PERMITTED
VENT TERMINATION
X
AIR SUPPLY INLET
V
Canadian Installations1
US Installations2
A = Clearance above grade, veranda, porch,
deck, or balcony
12” (30cm)
12” (30cm)
B = Clearance to window or door that may be
opened
6” (15cm) for appliances
6” (15cm) for appliances
< 10,000 Btuh (3kW), 9”
(23cm) for appliances > 10,000
Btuh (3kW) and < 50,000 Btuh
(15kW), 12” (30cm) for
< 10,000Btuh (3kW), 12” (30cm)
for appliances > 10,000 Btuh (3kW) and
< 100,000 Btuh (30kW), 36” (91cm)
for appliances > 100,000 Btuh (30kW)
appliances > 50,000 Btuh (15kW)
C = Clearance to permanently closed window
12” (305mm) recommended to
prevent window condensation
12” (305mm) recommended to
prevent window condensation
D = Vertical clearance to ventilated soffit located
above the terminal within a horizontal
distance of 2’ (610mm) from the center
line of the terminal
18” (458mm)
18” (458mm)
E = Clearance to unventilated soffit
F = Clearance to outside corner
G = Clearance to inside corner (see next page)
12” (305mm)
see next page
see next page
12” (305mm)
see next page
see next page
H = Clearance to each inside of center line
extended above meter/regulator assembly
3’ (91cm) within a height of 15’ (5m)
above the meter/regulator assembly
3’ (91cm) within a height of 15’
(5m) above the meter/regulator
assy
I = Clearance to service regulator vent outlet
3’ (91cm)
3’ (91cm)
J = Clearance to nonmechanical air supply inlet 6” (15cm) for appliances < 10,000
to building or the combustion air inlet to any Btuh (3kW), 12” (30cm) for
6” (15cm) for appliances
< 10,000 Btuh (3kW), 9”
(23cm) for appliances > 10,000
Btuh (3kW) and < 50,000 Btuh
(15kW), 12” (30cm) for
other appliances
appliances > 10,000 Btuh (3kW) and
< 100,000 Btuh (30kW), 36” (91cm)
for appliances > 100,000 Btuh (30kW)
appliances > 50,000 Btuh (15kW)
K = Clearance to a mechanical air supply inlet
6’ (1.83m)
3’ (91cm) above if within 10
feet (3m) horizontally
L = Clearance above paved sidewalk or paved 7’ (2.13m)†
driveway located on public property
7’ (2.13m)†
M = Clearance under veranda, porch, deck or
balcony
12” (30cm)‡
12” (30cm)‡
N = Clearance above a roof shall extend a minimum of 24” (610mm) above the highest point when it passes through the roof
surface, and any other obstruction within a horizontal distance of 18” (450mm).
1 In accordance with the current CSA-B149 Installation Codes
2 In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes
† A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and
serves both dwellings
‡ only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor:
NOTE: 1. Local codes or regulations may require different clearances.
2. The special venting system used on Direct Vent Fireplaces are certified as part of the appliance, with clearances tested and
approved by the listing agency.
3. CFM Corporation assumes no responsibility for the improper performance of the appliance when the venting system does not
meet these requirements.
Fig. 15 Vent termination locations.
20010667
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Termination Clearances
Termination clearances for buildings with combustible and noncombustible exteriors.
Inside Corner
Alcove Applications*
Outside Corner
D
C
C
F =
Combustible
6" (152 mm)
G =
Combustible
6" (152 mm)
V
G
V
Noncombustible
2" (51 mm)
V
E
Noncombustible
2" (51 mm)
O
F
Balcony -
with no side wall
Balcony -
with perpendicular side wall
E = Min. 6” (152 mm) for
non-vinyl sidewalls
Min. 12” (305 mm) for
vinyl sidewalls
O = 8’ (2.4 m) Min.
M
No.
of Caps
M
V
DMin.
CMax.
V
1
2
3
4
3’ (.9 mm) 2 x DActual
6’ (1.8 m) 1 x DActual
9’ (2.7 m) 2/3 x DActual
12’ (3.7 m) 1/2 x DActual
P
Combustible &
Noncombustible
M =
Combustible &
Noncombustible
12" (305 mm)
M = 24" (610 mm)
P = 20” (508 mm)
DMin. = # of Termination caps x 3
CMax. = (2 / # termination caps) x DActual
584-15
*NOTE: Termination in an alcove space (spaces open only on one side and with an overhang) is permitted with the dimensions
specified for vinyl or non-vinyl siding and soffits. 1. There must be a 3’ (914 mm) minimum between termination caps. 2. All
mechanical air intakes within 10’ (1 m) of a termination cap must be a minimum of 3’ (914 mm) below the termination cap. 3. All
gravity air intakes within 3’ (914 mm) of a termination cap must be a minimum of 1’ (305 mm) below the termination cap.
Fig. 16 Termination clearances.
General Information Assembling Vent Pipes
Canadian Installations
* Be sure the vent is actually crushed before proceed-
ing. Apply a tug to be sure the vent will not slip off the
collars.
Repeat process with 7” flex vent pipe. The same proce-
dure must be performed on the vent side.
The venting system must be installed in accordance
with the current CSA-B149.1 installation code.
USA Installations
The venting system must conform to local codes and/or
the current National Fuel Code ANSI Z223.1/NFPA 54.
Apply High Temperature
Sealant
Only venting components manufactured by CFM Cor-
poration may be used in Direct Vent systems.
Flex Vent Pipes
Before joining the flex vent pipe to the unit, apply a
bead of high temperature sealant* (provided) to the 4”
pipe exiting the fireplace. Secure flex vent piep in place
with a hose clamp (provided).
*Be sure the flex pipe overlaps at least 1” (25mm) onto
the collars of the fireplace and termination. If the ter-
mination has an internal bead, be sure to overlap and
secure 1” (25 mm) past the bead.
Hose Clamp
FP1471
Fig. 17 Apply high temperature sealant to 4” and 7” pipes.
20010667
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Twist Lock Pipes
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
When using twist lock pipe it is not necessary to use
sealant on the joints. The only areas of the venting
system that need to be sealed with high temperature
silicone sealant are the sliding joints of any telescopic
vent section used in the system.
To join twist lock pipes together, simply align the beads
of the male end with the grooves of the female end,
twisting the pipe until the flange on the female end
contacts external flange on the male end. It is recom-
mended that you secure the joints with three (3) sheet
metal screws, however, this is not mandatory with twist
lock pipe. (Fig. 18)
To make it easier to assembly the joints, we suggest
putting a lubricant (Vaseline or similar) on the male end
of the twist lock pipe prior to assembly.
eg: A
Male End
Female End
8
7
eg: B
6
5
4
3
Screw Holes
TWL100
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20
Fig. 18 Twist-lock pipe joints.
Horizontal dimension from the outside face of the
wall to the center of the fireplace vent flange
How to Use the Vent Graph
The Vent Graph should be read in conjunction with the
following vent installation instructions to determine the
relationship between the vertical and horizontal dimen-
sions fo the vent system.
Fig. 19 Sidewall venting graph. (Dimensions in feet)
Refer to Page 20 for venting requirements for snor-
kels.
1. Determine the height of the center of the horizontal
vent pipe exiting through the outer wall. Using this
dimension on the Sidewall Vent Graph (Fig. 19),
locate the point intersecting with the slanted graph
line.
Rear Wall Vent Application
When installed as a rear vent unit this appliance may be
vented directly to a termination located on the rear wall
behind the appliance.
2. From the point of this intersection, draw a vertical
line to the bottom of the graph.
•
Only CFM Corporation venting components are
approved to be used in these applications (See
‘Venting Components’ listed for different installation
requirements).
3. Select the indicated dimension, and position the
fireplace in accordance with same.
EXAMPLE A:
•
The maximum horizontal distance between the rear
of the appliance (or end of the transition elbow in a
corner application) and the outside face of the rear
wall is 20” (508mm). (Fig. 20, 21)
If the vertical dimension from the floor of the unit is 11’
(3.4m) the horizontal run to the face of the outer wall
must not exceed 14’ (4.3m).
•
•
Only one 45° elbow is allowed in these installations.
Minimum clearances between vent pipe and com-
bustible materials are as follows:
EXAMPLE B:
If the vertical dimension from the floor of the unit is 7’
(2.1m), the horizontal run to the face of the outer wall
must not exceed 8¹⁄₂’ (2.6m).
Top - 2” (51 mm)
Sides - 1” (25 mm)
Bottom - 1” (25 mm)
20010667
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Vent Opening for Combustible Walls
9³⁄₈”
(240 mm)
Rear Vent Top View
20” (508 mm)
Max.
10³⁄₈”
(265 mm)
DVR584-600
Framing Detail
Fireplace Hearth
Fig. 20 Rear vent application, no elbows.
20”
(508 mm)
Max.
Opening for Noncombustible Wall
20”
(508 mm)
Max.
7¹⁄₂”
(190 mm)
45°
45°
Fireplace Hearth
VO584-100
Fig. 22 Locate vent opening on wall.
Max. Length
12” (305 mm)
Adjustable Zero
Clearance Sleeve
FP836
Rear Vent Top View, Corner Installation
#8 Screws (2)
Fig. 21 Rear vent application, one 45° elbow.
#8 Screws
(2)
Rear Wall Vent Installation
Twist Lock Pipe
#8 Screws
(2)
Step 1
Locate and cut the vent opening in the wall.
For combustible walls first frame in opening. (Fig. 22)
Firestop
Adjustable Zero
NOTE: When using flex vent, the opening will have to
be measured according to the 1” (25mm) rise in 24”
(610mm) vertical run.
Clearance Sleeve
ZCS101
Fig. 23 Adjustable zero clearance sleeve.
Step 4
Combustible Walls: Cut a 10³⁄₈”H x 9³⁄₈” W (265 mm
x 240 mm) hole through the exterior wall and frame as
shown. (Fig. 22)
Install the 4” (102 mm) vent to the appliance collar and
secure with 3 sheet metal screws. Install the 7” (178
mm) vent pipe to the appliance collar and secure with 3
sheet metal screws. It is not necessary to seal this con-
nection. If a 45° elbow is being used attach the elbow
to the appliance in the same manner then attach the
venting to the elbow.
Noncombustible Walls: Hole opening should be 7¹⁄₂”
(191mm) diameter.
Zero clearance sleeve is only required for
combustible walls.
It is critical that there is no downward
slope away from the appliance when con-
necting the vent or elbow.
Step 2
Measure wall thickness and cut zero clearance sleeve
parts to proper length (Maximum 12” / 305 mm). As-
semble sleeve to its maximum opening (10³⁄₈” x 9³₈”)
and attach to firestop assembly. (Fig. 23)
Step 5
Guide the venting through the vent hole as you place
the appliance in its installed position. Guide the 4”
(102 mm) and 7” (178 mm) collar of the vent termina-
tion into the outer ends of the venting. Do not force
the termination. If the vent pipes do not align with the
termination, remove and realign the venting at the appli-
ance flue collars. (Fig. 24) Attach the termination to the
wall as outlined in the instruction sheet supplied with
the termination.
Step 3
Measure the horizontal length requirement for the vent-
ing including a 2” (51 mm) overlap, i.e. from the elbow
to the outside wall face plus 2” (51 mm). (Fig. 21)
20010667
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Finished Wall
Rise
Vent
Termination
FP1472
Fig. 26 There must be a 1/2” rise per foot length.
Vertical Sidewall Application
Since it is very important that the venting system
maintain its balance between the combustion air
intake and the flue gas exhaust, certain limitations
as to vent configurations apply and must be strictly
adhered to.
FP1005
The Vent Graph, showing the relationship between ver-
tical and horizontal side wall venting, will help to deter-
mine the various dimensions allowable.
Fig. 24 Side view of final unit location.
Rear Wall Vent Installations -
Flex Vent Pipe
Minimum clearance between vent pipes and com-
bustible materials is one inch (25 mm) on top, bot-
tom and sides unless otherwise noted.
Follow Steps 1 and 2 on Page 15.
Step 3
When vent termination exits through foundations less
than 20” (508 mm) below siding outcrop, the vent pipe
must flush up with the siding.
Install the 4” (102 mm) flex vent pipe to the appliance
collars described in “General Information Assembling
Vent Pipes”, Page 12. If the installation requires a 45°
angle, grasp the vent pipe close to the appliance collar
and bend to 45°. DO NOT exceed 45°. (Fig. 25)
It is best to locate the fireplace in such a way that mini-
mizes the number of offsets and horizontal vent length.
The horizontal vent run refers to the total length of vent
pipe from the flue collar of the fireplace (or the top of
the Transition Elbow) to the face of the outer wall.
Install the 7” vent pipe in the same manner as Step 2.
Termination
Horizontal plane means no vertical rise exists on this
portion of the vent assembly.
Flex Section
Appliance Collars
When installing the appliance as a rear
vent unit, the 90° or 45° Transition Elbow
attached directly to the rear of the unit is
NOT INCLUDED in the following criteria
and calculations, and unless specifically
mentioned should be ignored when calcu-
lating venting layouts.
•
•
The maximum number of 90° elbows per side wall
installation is three (3). (Fig. 27)
If a 90° elbow is fitted directly on top of the fireplace
flange the maximum horizontal vent run before the
termination or a vertical rise is 36” (914 mm). (Fig.
28)
FP1473
Fig. 25 Grasp the vent pipe close to the collar and bend to
45° angle. Do not exceed 45°.
NOTE: There must be a 1/2” (13 mm) rise in a 12”
(305 mm) length of flex vent.
Step 4
Assemble the flex vent to the collars on the termination
as you did on the appliance.
20010667
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
7’
3 x 90°
Elbows
3 x 90°
Elbows
(2.1 m)
A
10’
(3 m)
B
FP1176
8’
Fig. 27 Maximum three (3) 90° elbows per installation.
(2.4 m)
36"
(914mm)
Max.
36"
(914mm)
Max.
V584-201
Fig. 30 Maximum vent run with elbows.
In Figures 29 & 30, dimension A plus B must not be
greater than 17’ (5.2m)
•
The maximum number of 45° elbows permitted per
side wall installation is two (2). These elbows can be
installed in either the vertical or horizontal run.
For each 45° elbow installed in the horizontal run,
the length of the horizontal run MUST be reduced by
18” (457 mm). This does not apply if the 45° elbows
are installed on the vertical part of the vent system.
The maximum number of elbow degrees in a system
is 270°. (Fig. 31)
FP1177
Fig. 28 Maximum horizontal run with no rise.
•
•
If a 90° elbow is used in the horizontal vent run
(level height maintained) the horizontal vent length
is reduced by 36” (914 mm). (Fig. 29, 30) This does
not apply if the 90° elbows are used to increase or
redirect a vertical rise. (Fig. 27)
•
Example:
Example: According to the vent graph (Page 14) the
maximum horizontal vent length in a system with a 7¹⁄₂’
(2.3 m) rise is 20’ (6 m) and if a 90° elbow is required in
the horizontal vent it must be reduced to 17’ (5.2 m).
Elbow 1 = 90°
Elbow 2 = 45°
Elbow 3 = 45°
Elbow 4 = 90°
Total angular variation = 270°
B
A
1
2
3
4
1
2
3
4
A + B = 17' (Max.)
(5.2m)
7'6"
(2.3m)
FP1180
1 + 2 + 3 + 4 = 270°
Fig. 31 Maximum elbow usage.
FP1178
Fig. 29 Horizontal run reduction.
20010667
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Vertical Sidewall Installation
Twist Lock Pipe
Max. Length
12” (305 mm)
Adjustable Zero
Clearance Sleeve
Step 1
#8 Screws (2)
Locate vent opening on the wall. It may be necessary
to first position the fireplace and measure to obtain hole
location. Depending on whether the wall is combustible
or noncombustible, cut opening to size. (Fig. 32) (For
combustible walls first frame in opening.)
#8 Screws
(2)
#8 Screws
(2)
NOTE: When using flex vent, the opening will have to
be measured according to the 1/2” (13 mm) rise in 12”
(305 mm) vent run.
Firestop
Adjustable Zero
Clearance Sleeve
Combustible Walls: Cut a 9³⁄₈”H x 9³⁄₈”W (240 mm x
240 mm) hole through the exterior wall and frame as
shown. (Fig. 32)
ZCS101
Fig. 33 Adjustable zero clearance sleeve.
Noncombustible Walls: Hole opening must be 7¹⁄₂”
(191mm) in diameter.
Vent Opening for Combustible Walls
X
X
9³⁄₈”
(240 mm)
9³⁄₈”
(240 mm)
FP1181
Fig. 34 Vertical height requirements.
Framing Detail
Fireplace Hearth
Step 4
Opening for Noncombustible Wall
Apply a band of silicone to the inner and outer flue
collars of the fireplace and using appropriate length of
pipe section(s) attach to fireplace with three (3) screws.
Follow with the installation of the inner and outer elbow,
again secure joints with three (3) sheet metal screws.
Wipe off any excess high temperature sealant.
7¹⁄₂”
(190 mm)
Fireplace Hearth
VO584-100
Step 5
Fig. 32 Locate vent opening on wall.
Measure the horizontal length requirement including a
2” (51mm) overlap, i.e. from the elbow to the outside
wall face plus 2” (51mm) (or the distance required if
installing a second 90° elbow). (Fig. 35)
Step 2
Measure wall thickness and cut zero clearance sleeve
parts to proper length (MAXIMUM 12” / 305 mm).
Assemble sleeve and attach to firestop with #8 sheet
metal screws (supplied). Install firestop assembly. (Fig.
33)
Always install horizontal venting on a level
plane.
Zero clearance sleeve is only required for
combustible walls.
Step 6
Use appropriate length of pipe sections - telescopic or
fixed - and install. The sections which go through the
wall are packaged with the starter kit, and can be cut to
suit if necessary.
Step 3
Place fireplace into position. Measure the vertical height
(X) required from the base of the flue collars to the cen-
ter of the wall opening. (Fig. 34)
Sealing vent pipe and firestop gaps with high tem-
perature sealant will restrict cold air being drawn in
around fireplace.
20010667
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
X
4” Flex Vent Pipe
12"
(305mm)
X
Spacer Spring
6"
(152mm)
5"
(127mm)
6³⁄₄"
(172mm)
FP1474
FP1182
Fig. 36 Install spacer springs.
Fig. 35 Horizontal length requirement.
Step 4
Step 7
Install the 4” (102 mm) flex vent pipe to the appliance
collar as described on Page 13. Secure the end with the
first spring 6³⁄₄” (172 mm) from the flex pipe end to the
unit.
Apply high temperature sealant to 4” (102 mm) and
7” (178 mm) collars or the termination one inch away
from crimped end. Guide the vent terminations 4” and
7” collard into their respective vent pipes. Double check
that the vent pipes overlap the collars by 2” (51 mm).
Secure the termination to the wall with screws provided
and caulk around the wall plate to weatherproof. As an
alternative to screwing the termination directly to the
wall, you may also use expanding plugs or an approved
exterior construction adhesive. You may also attach the
termination with screws through the inner body into the
4” vent pipe, however for this method, you must extend
the 4” pipe approximately 6” (152 mm) beyond the outer
face of the wall.
Step 5
Slide the 7” (178 mm) flex vent pipe over the 4” flex
vent pipe and secure the 7” collar as described on Page
13.
Step 6
Bend the flex pipe horizontal so the bottom of the hori-
zontal pipe measure 6¹⁄₂” (165 mm) from the top of the
unit immediately after the 90° formation. (Fig. 37) Be
sure to follow the 1/2” (13 mm) rise in a 12” (305 mm)
horizontal run rule.
Support horizontal pipes every 36”
(914 mm) with metal pipe straps.
Step 7
Install the 4” flex then 7” flex to the termination.
Vertical Sidewall Installation
Flex Vent Pipe
NOTE: The 40” (1016 mm) flex vent is used for 90° off
the top of the unit then out the back wall.
6¹⁄₂" (165mm)
Follow Step 1 and 2 on Page 18.
Step 3
Install the four (4) spacer springs on the 4” flex vent
pipe. When installing the spacer springs around the 4”
pipe, stretch the spring to approximately 15” (381 mm),
wrap the spring around the pipe and interlock the ends
of the spacer spring approximately 2” (51 mm). Mea-
sure 6³⁄₄” (172 mm) from the end of the pipe. Place the
next spring 5” (127 mm) from the previously installed
spring. Place the next spring 6” (152 mm) from the last
spring. Finally place the last spring 12” (305 mm) from
the last spring installed. (Fig. 36)
FP1475
Fig. 37 Bend flex vent at 90° so horizontal portion is 6¹⁄₂”
(165 mm) off top of unit.
20010667
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Do not back fill around snorkel.
Below Grade Installation
A clearance of at least 4” must be main-
tained between the snorkel and the soil.
When it is not possible to meet the required vent ter-
minal clearances of 12” (305 mm) above grade level, a
snorkel kit is recommended. It allows installation depth
down to 7” (178 mm) below grade level. The 7” (178
mm) is measured from the center of the horizontal vent
pipe as it penetrates through the wall.
If the foundation is recessed, use recess brackets (not
supplied) for securing lower portion of the snorkel. Fas-
ten brackets to wall first, then secure to snorkel with self
drilling #8 x 1/2 sheet metal screws. It will be necessary
to extend vent pipes out as far as the protruding wall
face. (Fig. 39)
Ensure the sidewall venting clearances are ob-
served. If venting system is installed below ground,
we recommend a window well with adequate and
proper drainage to be installed around the termina-
tion area.
If installing a snorkel, a minimum 24” (610 mm) vertical
rise is necessary. The maximum horizontal run with the
24” vertical pipe is 36” (914 mm). This measurement
is taken from the collar of the fireplace (or transition
elbow) to the face of the exterior wall. See the Sidewall
Venting Graph for extended horizontal run if the vertical
exceeds 24” (610 mm).
Snorkel
Foundation
Recess
Wall Screws
Watertight
Seal Around
PIpe
Sheet Metal Screws
1. Establish vent hole through the wall (Fig. 32)
2. Remove soil to a depth of approximately 16”
(406mm) below base of snorkel. Install drain pipe.
Install window well (not supplied). Refill hole with 12”
(305 mm) of coarse gravel leaving a clearance of ap-
proximately 4” (102 mm) below snorkel. (Fig. 38)
3. Install vent system.
BG401
Fig. 39 Snorkel installation, recessed foundation.
Vertical Through-the-Roof Application
This gas fireplace has been approved for:
4. Ensure a watertight seal is made around the vent
pipe coming through the wall.
5. Apply high temperature sealant caulking (supplied)
around the 4” and 7” snorkel collars.
•
Vertical installations up to 40’ (12 m) in height. Up
to a 10’ (3 m) horizontal vent run can be installed
within the vent system using a maximum of two 90°
elbows. (Fig. 40)
6. Slide the snorkel into the vent pipes and secure to
the wall.
7. Level the soil so as to maintain a 4” (102 mm) clear-
ance below snorkel. (Fig. 38)
•
Up to two 45° elbows may be used within the hori-
zontal run. For each 45° elbow used on the horizon-
tal plane, the maximum horizontal length must be
reduced by 18” (450 mm).
Example: Maximum horizontal length:
No elbows = 10’ (3 m)
Zero Clearance
Screws
Sleeve
7TDVSNORK
(Snorkel)
(if required)
1 x 45° elbow = 8.5’ (2.6 m)
2 x 45° elbows = 7’ (2.1 m)
Firestop
4” (102mm)
Clearance
Min.
•
•
A minimum of an 8’ (2.5 m) vertical rise is required.
Two sets of 45° elbow offsets may be used within the
vertical sections. From 0 to a maximum of 8’ (2.5 m)
of vent pipe can be used between elbows. (Fig. 41)
7DVCS supports offsets. (Fig. 43) This application
will require that you first determine the roof pitch
and use the appropriate starter kit. (Refer to Venting
Components List)
7” Pipe
Window
Well
24” (610mm)
Minimum*
•
Gravel
Drain
•
•
The maximum angular variation allowed in the sys-
tem is 270°. (Fig. 41)
The minimum height of the vent above the highest
point of penetration through the roof is 2’ (610 mm).
(Fig. 44) Refer to note 2, Page 14.
Foundation Wall
*A minimum of 24” (610 mm)
vertical pipe must be installed
when using the 7TDVSNORK
Kit.
BG402a
Fig. 38 Below grade installation.
20010667
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Vertical Through-the-Roof Installation
Max. Height 40’ (12.2 m)
Min. Height 8’ (2.4 m)
1. Locate your fireplace.
2. Plumb to center of the (4”) flue collar from ceiling
above and mark position.
3. Cut opening equal to 9³⁄₈” x 9³⁄₈” (240 mm x 240 mm).
Max. 10’ (3 m)
4. Proceed to plumb for additional openings through
the roof. In all cases, the opening must provide a
minimum of 1 inch clearance to the vent pipe, i.e., the
hole must be at least 9³⁄₈” x 9³⁄₈” (240 mm x 240 mm).
5. Place fireplace into position.
6. Place firestop(s) #7DVFS or Attic Insulation Shield
#7DVAIS into position and secure. (Fig. 42)
Support Straps
Every 3’ (.9 m)
7. Install roof support (Fig. 43) and roof flashing making
sure upper flange is below the shingles. (Fig. 45)
8. Install appropriate pipe sections until the venting is
above the flashing. (Fig. 45)
Max.
Max. 10’ (3 m)
9. Install storm collar and seal around the pipe.
Height 40’ (12.2 m)
Min.
10. Add additional vent lengths for proper height. (Fig.
45)
Height 8’ (2.4 m)
11. Apply high temperature sealant to 4” and 7” collars
of vertical vent termination and install.
If there is a room above ceiling level, fire stop spacer
must be installed on both the bottom ad the top side
of the ceiling joists. If an attic is above ceiling level a
7DVAIS (Attic Insulation Shield) must be installed.
The enlarged ends of the vent section always face
downward.
FP1183
Fig. 40 Support straps for horizontal runs.
Attic Insulation
Shield
1 + 2 + 3 + 4 = 270°
1
1
2
2
3
3
4
4
Upper Floor
11”
(279 mm)
11”
(279 mm)
Ceiling Installation
FP1179
Joist
Fig. 41 Maximum elbow usage.
Firestop
Spacer
Nails (4)
FP1029
Fig. 42 Place firestop spacer(s) and secure.
20010667
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
3 #5 Sheet Metal
Screws per Joint
Typical Roof
Support
Application
Typical Ceiling
Support
Application
Sealant
Storm Collar
FP1184
Fig. 43 Venting supports.
Min.
2' (610 mm)
TWL101a
Fig. 45 Roof flashing.
FP1185
Fig. 44 Minimum termination to roof clearance.
20010667
22
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Venting Components
7TDVRVT - Through the wall Rear Vent Termination
Starter Kit -
Model 7TDVSK - Sidewall Venting (Twist Lock Pipe)
Model 7FDVSK - Sidewall Venting (Flex Vent Pipe)
Models 7TDVTK/TV - Hot Touch Termination Kits
Model 7TDVTVTK/TV - Cool Touch Termination Kit
Starter Kit - Model 7TDVSKV - Vertical Venting
for 7TDVSKV-A order 1/12 to 6/12 roof pitch
for 7TDVSKV-B order 7/12 to 12/12 roof pitch
for 7TDVSKV-F order flat roof
Starter Kit for Below Grade Installation
Model 7TDVSKS -Snorkel Kit (Twist Lock Pipe)
Model 7FDVSKS -Snorkel Kit (Flex Vent Pipe)
Starter Pipe
Model 7TDVP 20/8 - 24” Starter Pipe Bulk
Model 7FDVP 30/8 - 30” Flex Pipe Bulk
45o Elbow
7TDV45 for Rear Vent to Vertical Vent
or Vertical/Horizontal Offsets
90o Transition Elbow
7TDVRT90 for Rear Vent to Vertical Vent
90° Elbow
7TDV90 Vertical/Horizontal Offset
Telescopic vent sections
7TDVP1117 -11” to 17” adjustable length
7TDVP3567 -35” to 67” adjustable length
Pipe sections for vertical or horizontal venting
Model 7TDVP8”
Model 7TDVP12”
Model 7TDVP24”
Model 7TDVP36”
Model 7TDVP48”
-
-
-
4 per box
4 per box
4 per box
Firestop Spacer
Model 7DVFS
Attic Insulation Shield
Model 7DVAIS
Vertical/Horizontal Combination Offset Support
Model 7DVCS
20010667
23
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Operating Instructions
Window Frame
Assembly
Glass Information
Only glass approved by CFM Corporation
should be used on this fireplace.
Fireplace Front
•
The use of any non-approved replace-
ment glass will void all product warranties.
Care must be taken to avoid breakage of the glass.
Do not operate appliance with glass front re-
moved, cracked or broken.
Clamps
•
•
Glass
Panel
•
Replacement glass (complete with gasket) is
available through your CFM Corporation dealer
and should only be installed by a licensed quali-
fied service person.
Glass
Panel
Pull Clamp
Hook
Push Clamp
Handle
Louvre Removal
FP771a
To remove louvre
assembly top, pull
louvre up and then
lift out. The louvre
assembly bottom
is hinged at the
bottom edge and
swings down. (Fig.
46)
Fig. 47 Window frame assembly removal.
ed). After the initial cleaning process the glass should
be cleaned two or three times during each operating
season depending on the environment in the house.
2.
Louvre
1.
Clean the glass after the first two weeks of
operation.
Do not clean glass when hot.
Do not use abrasive cleaners.
Do not strike or slam the glass.
Glass Panel
FP444
Fig. 46 Remove louvre assembly
top.
Installation of Optional Ceramic Panels
DV360
Window Frame Assembly Removal
1. Remove glass.
1. Turn the fireplace OFF (including the pilot).
2. Remove glass heat shield located at the top of the
firebox toward the front.
2. If the unit has been operating, allow time for the
components to cool.
3. Place the rear panel behind the rear log bracket.
3. Remove louvre assembly top.
4. Slide the right and left panels into place, The right
and left panels will hold the rear panel in place when
positioned properly.
4. Open the louvre assembly bottom.
5. Release the two clamps along lower edge of the
frame by pulling down on clamp handles. (Fig. 47)
5. Replace the glass heat shield.
6. Tilt window frame assembly out slightly at the bot-
tom, lift the frame up and away from the fireplace.
6. Place the right and left hearth refractories and bring
them together in the center and slide towards the
front of the unit.
7. To replace window frame assembly reverse proce-
dure.
Replacement of
Ceramic Hearth Panels
Glass Cleaning
It is necessary to clean the glass periodically. During
start-up condensation, which is normal, forms on the
inside of the glass and causes lint, dust and other air-
borne particles to cling to the glass surface. Also initial
paint curing may deposit a slight film on the glass. It
is therefore recommended the glass be cleaned two or
three times with a non-ammonia household cleaner and
warm water (gas fireplace glass cleaner is recommend-
1. Remove glass.
2. Set left and right panels on hearth and bring towards
front of unit.
20010667
24
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Screw
Screw
Burner
Log Identification Chart
Logs
DV360
20010673
20010672
20010675
--
20010676
--
20010677
20010674
DV580
E9
E10
E8
E12
E13
E11
--
Log Front Left
Log Front Right
Log Rear
Log Top Left
Log Top Right
Log Front Center
Log Top Center
Log Overlay
Grate
Hearth Panels
Front of Unit
H100a
Fig. 48 Hearth panel location.
--
Installation of Logs
Remove front glass. (Refer to “Window Frame As-
sembly Removal” Section, Fig. 47) Remove logs from
packaging.
As with all plastics — these are not toys
and should be kept away from children
and infants.
DV360
NOTE: Refer to Figure 49 for bracket and bend loca-
Pilot Front
Shield
Left Edge
of Bracket
tions.
Rear Log
Bracket
Stop
1. Place the log front right. Hold the log with the pointed
end toward the left. Place on top of burner toward
the right. Slide the log toward the front until it comes
in contact with the bracket at the front of the burner
housing behind the burner tube. (Fig. 49) Adjust the
log until the pointed end on the left is aligned with
the left edge of the bracket. (Fig. 50) NOTE: Gently
push down on the right rear of the log so the pilot
front shield cuts slightly into the log. This will help to
ensure proper log position.
Bracket
Pilot
Bracket
Bend
Front Left
Bend
Front
Brackets
FP1653
Fig. 49 Burner brackets and bends.
Figure 50
Log Front Right
LG477
Front Brackets
20010667
25
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Figure 51
2. Place the log overlay. Hold the overlay with the flat
side down and large cut out for the middle flame
on the right. Set the overlay on top of the burner
toward the left front inside the stop bracket on
the left end and the bend on the front left of the
burner. (Fig. 49) Rotate the right end of the
overlay clockwise until it makes contact with
the back of the log front right. NOTE:
Log Overlay
This is very critical as improper
positioning of the overlay will
affect the flame and the per-
formance of the unit. (Fig. 51)
LG478
Log Rear
Figure 52
3. Place log rear. The rear log sits
in the firebox at an angle toward
the left over the rear log bracket
and the left side of the burner.
(Fig. 49) Set the log on the rear
log bracket. The notch on the right
side will go over the pilot. Swing
the left end of the log toward the
front until it makes contact with the
stop bracket. Slide the log to the
right so the pilot notch on the log
makes contact with bend on the
left of the pilot bracket. (Fig. 52)
LG462
Locator Pins
4. Place the glowing embers by
building them up lightly between
the fettle and the burner tube as-
sembly. (Fig. 53)
Figure 53
5. Place the log front left. Set the
log by matching the square hole
on the bottom with the pins on
the overlay. The right side of this
log should come in contact with
the left andiron. Lay the log at an
angle to the left over the fettle.
When this log is in place, it must
not cover the front left opening of
the overlay. (Fig. 54)
LG463
Glowing Embers
20010667
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
6. Place the log top cen-
ter. Hold the log with
Figure 54
Log Top Right
Log Top Center
the pointed end toward
the back. Match the two
holes on the bottom of
the log with the two pins
Log
Rear
on the top of the log front right.
(Refer to Figure 53 for pin loca-
tions) Set the log and lay it into
the rear log. (Fig. 54)
Log
Front
Right
7. Place the log top right. Hold the
log with pointed end to the left.
Match the two holes on the bot-
tom of the log with the two pins
on the rear log and set the fork
on the log over the right front
log. (Fig. 54)
8. Place the lava rock on the
hearth refractory in the front
as desired. (Fig. 54)
LG464
Lava Rock
Log Front Left
DV580
Refer to Figure 51.
Log Top Left
(E12)
Log Rear
(E8)
1. Place rear log (E8) on rear
bracket (ensure the notch on
the left end is centered on
the left side of rear bracket),
so it will not move from side
to side and is firmly posi-
Log Top Right
(E13)
Log Front
Left
(E9)
tioned on the bracket. Be
sure log is as far forward as
possible on bracket. (Fig. 55)
Log Front
Right
(E10)
2. Place front left log (E9) on
top of burner, left side. Align
log’s bottom holes with left
bracket log locator studs.
3. Place front right log (E10)
on top of burner, right side.
Align log’s bottom holes
with right bracket log locator
studs. (Fig. 50)
4. Place top left log (E12). Use
log’s bottom hole to locate
it onto rear log left (E8) and
just rest bottom cut out log
onto the grate assembly.
Burner Lava Rock and
1/3 of the bag of Embers
Log Front
Center (E11)
LG395
Fig. 55 DV580 log, burner lava rock and ember placement.
5. Place top right log (E13).
7. Place large lava rock around the front grate.
Use log’s bottom hole to locate it onto rear log right
(E8) and the bottom of top right log rest onto front
right log (E10).
Top logs must be placed properly onto
notches.
6. Place front center log (E11). Position the log notch
against the center grate assembly and the bottom of
front center log rest onto front right log (E10).
20010667
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Flame Characteristics
Burner Lava Rock Placement
It is important to periodically perform a visual check of
the pilot and the burner flames. Compare them to the
illustrations below (Figs. 58, 59). If any of the flames
appear abnormal call a service person.
Place burner lava rock on the burner in front of the front
logs. Do not place burner lava rock in the inside corners
of the front logs.
Large Lava Rock
PSE Pilot
The large lava rock provided with this fireplace must
be placed on the firebox base around the sides of the
burner assembly and on the tray beneath the grate.
3/8” - 1/2”
(10 - 13 mm)
Under no circumstances should this large
lava rock be placed on any part of the
burner assembly.
SIT Pilot
F584-703
Flame & Temperature Adjustment
Fig. 58 Correct pilot flame appearance.
For fireplaces equipped with Hi/Lo valves, flame adjust-
ment is accomplished by rotating the Hi/Lo adjustment
knob located near the center of the gas control. (Fig. 56
or 57)
Inspecting the Venting System
This appliance venting system is designed and con-
structed to develop a positive flow adequate to remove
flue gases to the outside atmosphere.
Turn
Any foreign objects in the venting system, except those
designed specifically for the venting system, may cause
spillage of flue gases.
counterclockwise
to decrease
flame height
Turn clockwise
to increase
flame height
To inspect the venting system, make sure the main gas
valve is off. Remove window frame assembly (Refer to
Window Frame Assembly Removal Section). Using a
flashlight, check the area above the baffle in the com-
bustion dome. Clean if necessary.
Fig. 56 Flame adjustment knob for Honeywell valve.
Turn
Turn clockwise
to decrease
flame height
counterclockwise
to increase
flame height
Fig. 57 Flame adjustment knob for SIT valve.
20010667
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Yellow Flame
Yellow Flame
LG444
DV360
Red Glow
LG396
DV580
Red Glow
Fig. 59 Correct burner flame apperance for DV360 and DV580.
20010667
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Lighting and Operating Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This heater has a pilot which must be lit manu-
ally. When lighting the pilot follow these instruc-
tions exactly.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call
the Fire Department
B. BEFORE LIGHTING smell all around the
heater area for gas. Be sure to smell next to
the floor because some gas is heavier than air
and will settle on the floor.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, do not try to repair it, call a
qualified service technician. Applying force or any
attempted repair may result in a fire or explosion.
D. Do not use this fireplace if any part has been under
water. Immediately call a qualified service techni-
cian to inspect the heater and to replace any part of
the control system and any gas control which has
been under water.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any fireplace
• Do not touch any electric switch
• Do not use any phone in your building
• Immediately call your gas supplier from a
neighbor’s phone.
Lighting Instructions
1. STOP! Read the safety information above.
2. Turn off all electrical power to the fireplace.
3. For MN/MP/TN/TP appliances ONLY, go on to
Step 4. For RN/RP appliances turn the ON/OFF
switch to “OFF” position or set thermostat to
lowest level.
10. Push the control knob all the way in and hold.
Immediately light the pilot by repeatedly depress-
ing the piezo spark ignitor until a flame appears.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release knob and it
will pop back up. Pilot should remain lit. If it goes
out, repeat steps 5 through 8.
4. Open control access panel.
5. Push in gas control knob slightly and turn clock-
wise
to “OFF”.
3/8" - 1/2"
OFF
PILOT
o
2
O
Honeywell
Euro SIT
SIT NOVA
•
If knob does not pop up when released, stop
and immediately call your service technician or
gas supplier.
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety infor-
mation above. If you do not smell gas, go to the
next step.
7. Remove glass door before lighting pilot. (See
Glass Frame Removal section).
8. Visibly locate pilot by the main burner.
9. Turn knob on gas control counterclockwise
to “PILOT”.
•
If after several tries, the pilot will not stay lit,
turn the gas control knob to “OFF” and call your
service technician or gas supplier.
11. Replace glass door.
12. Turn gas control knob to “ON” position.
13. For RN/RP appliances turn the ON/OFF switch to
“ON” position or set thermostat to desired setting.
14. Turn on all electrical power to the fireplace.
To Turn Off Gas To Heater
1. Turn the ON/OFF switch to Off position or set
the thermostat to lowest setting.
3. Open control access panel.
4. Push in gas control knob slightly and turn clock-
2. Turn off all electric power to the fireplace if
service is to be performed.
wise
to “OFF”. Do not force.
5. Close control access panel.
20010667
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Lighting and Operating Instructions
For Fireplaces equipped with SIT822 Gas Valve (EN or EP)
Warning:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury and loss of life.
FOR YOUR SAFETY READ THE FOLLOWING WARNINGS
BEFORE LIGHTING THE APPLIANCE
Follow the gas suppliers instructions.
A. This fireplace is equipped with an ignition device
which automatically lights the pilot. DO NOT try to
light the pilot by hand.
• If you cannot contact your gas supplier call
the Fire Department
B. BEFORE OPERATING, smell all around the
appliance area for gas. Be sure to smell next to
the floor because some gas is heavier than the air
and will settle on the floor.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in
or turn by hand do not try to repair it, call a qualified
service technician. Force or attempting repair may
result in a fire or explosion.
What to do if you smell gas
• Do not try to light any appliance
• Do not operate any electrical switch.
• Do not use any phone in your building.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and replace any part of the
control system and any gas control that has been
under water.
• Immediately call your gas supplier from a
neighbor’s phone.
Lighting Instructions
1. STOP! Read the safety information above before
5. Turn the remote switch, if used, OFF. Turn the
wireless remote, if used, OFF.
continuing.
2. Turn off all electrical power to the appliance.
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas STOP. Follow instructions B in the safety
warnings above. If you do not smell gas go onto the
next step.
3. This appliance is equipped with an ignition device
which automatically lights the pilot. DO NOT try to
light the pilot by hand.
4. Access the gas control by lowering the lower
access door (louvre assembly).
7. Close the access door.
8. Turn ON all electrical power to the appliance.
9. Turn remote switch or wireless remote to “ON”.
10. If the appliance will not operate, follow the
instructions TURNING OFF THE GAS TO THE
APPLIANCE and call your service technician or
gas supplier.
HI
Turning Off the Gas to the Appliance
1/2” Gas Supply
1. Turn the remote switch to the “OFF” position.
2. Turn OFF all electrical power to the fireplace if
service is required.
1/2” NPT x 1/2” Flare Shut-Off
Valve
3/8” Flex Line
(From Valve)
3 Open the lower access panel.
4. Turn the shut-off valve on the flexible gas line to
the “OFF” position.
Valve in the on position
20010667
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Instructions for RF Comfort Control Valve
Shut Off Procedure
The Comfort Control Valve allows remote control of
temperature, fan and flame appearance.
If the manual switch is in the REMOTE position, the
transmitter can shut off the main burner and fan. How-
ever, the control is still on and a command from the
transmitter can turn on the main burner or fan.
NOTE: The antenna should hang in free air away from
grounded metal.
To shut off the system, turn the pilotstat knob clockwise
to the OFF position. This action closes the main gas
and safety valves. The transmitter cannot turn on the
main burner or fan.
Operation
1. If the manual switch is in remote position, switch it to
LOCAL. (Fig. 60)
2. Turn the pilotstat knob counterclockwise from OFF
to the PILOT position, push the knob down, and hold
in position. The pilot valve opens and allows gas to
flow to the pilot burner.
Transmitter Operation
Off Mode
In the OFF mode, the fireplace flame and fan are
off, the display will show OFF and displays the room
temperature. If the receiver is in REMOTE mode, the
fireplace will shut off.
3. Push plunger on the piezo until the pilot burner is lit.
When the pilot burner is lit, the LED on the control
will come on after approximately 40 seconds and will
be continuously red. When the light turns off which
will be approximately 10 seconds after it has been
continuously red, the receiver/valve is fully powered.
Display
Room Temperature
Set Temperature
Flame Height Level
Fan Speed Level
Motor Top Cap
Piezo Ignitor
Countdown Timer
Low Battery
Mode
Auto
On
Off
Flame
OFF
•
Up
Increases
Flame Height,
Fan Speed
Timer or Set
Point
Countdown
Timer
Down
Decreases
Flame, Fan
Speed Timer or
Set Point
Fan
LED
Pilostat
Knob
Plug
Antenna
Local/Remote
Switch
FP1039
FP1037
Fig. 61 Transmitter diagram.
Fig. 60 Comfort control valve.
On (Manual) Mode
4. Release the knob. The shaft will move upward. The
pilot burner should now stay burning. If the pilot
burner goes out, repeat step 2.
In the ON mode, the room temperature, flame and fan
levels will be shown. MANUAL will appear next to both
the flame and fan icons.
5. Turn the knob counterclockwise to the ON position. If
the manual switch is in the LOCAL position, the main
burner will turn on immediately.
When the control is in the ON mode, the flame and fan
levels, and delay timer are changed with the up and
down buttons. To change the flame level, press the
flame button followed by an arrow key. To change the
fan level, press the fan key followed by an arrow key.
Pushing the arrow key once will change the level by
one unit.
6. ON the initial use of a transmitter, a recognition
operation is required between the receiver/valve
and transmitter. Change the switch from LOCAL
to REMOTE. Press the fan or flame button on the
transmitter within 30 seconds. The LED will blink
indicating the transmitter will now work with the re-
ceiver/valve. If the switch continues in the REMOTE
position, the transmitter will now control the main
valve, flame modulation level and fan control.
7. If the manual switch is in the LOCAL position, the
valve will be at the highest fixed pressure setting.
The transmitter will control the fan only.
20010667
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Fan
Pilot Assembly
Delay Timer Mode
The shut off delay timer has a maximum of 2 hours and
a minimum of zero minutes. To change the timer level,
press the time key followed by an arrow key. Pushing
the key once will change the timer by 10 minutes.
Auto Mode
In the AUTO mode, the room temperature, set tem-
perature, flame and fan levels will be shown. AUTO will
appear next to both the flame and fan icons.
N A F
Red
When the control is in the AUTO mode, the main burner
will turn on/off or modulate based on the heat needed
to maintain the set temperature. The flame level will
change automatically to optimize the heat output
needed to maintain the set temperature. To change the
set temperature, press the up or down key. Pushing a
key once will change the temperature by one degree.
In the AUTO mode, the fan speed will increase with
increasing flame height or decrease with decreasing
flame height. “AUTO” is displayed next to the flame and
fan icons.
White
Red
White
White Dots
Antenna
Valve
(Bottom View)
FP1038
Fig. 58 Comfort Valve wiring diamgram.
Troubleshooting
1. Locate LED light on valve.
2. LED will blink after every valid command received by
the transmitter; this is not an error.
Fan Override During Auto Mode
If a lower or higher fan speed is desired when operating
in the AUTO mode, the fan speed can be overridden by
pushing the fan button followed by the up or down key.
Pushing a key once will change the fan level by one
unit. In this mode “AUTO” is displayed next to the flame
icon and “MANUAL” is displayed next to the fan icon.
3. Failure codes may occur anytime after pilot burner is
lit.
4. Sequence is failure code followed by light not blink-
ing for 30 seconds.
5. In the event of multiple failure codes, next failure
code follows previous failure code by approximately
3 seconds.
Change Between F/C Temperature Units
If an Error Code 3 is observed while performing the
testing, complete the following:
Push the up and down arrow keys simultaneously for
at least 3 seconds to toggle between Fahrenheit and
Celsius units.
1. Make sure the spade connectors are pushed all the
way on. If the Error Code 3 is still showing, then go
to the next step.
Disable Thermostat Function
2. Switch the front two thermopile leads with the back
two. Be sure the white lead is connected to the
spade with the white dot next to it. If the Error Code
3 is still showing, replace the thermopiles.
To disable the thermostat function in the AUTO mode,
push the time and down keys simultaneously for at
least 3 seconds.
To Change Batteries
If an Error Code 8 is observed while performing the
testing, complete the following:
1. Remove cover on the backside of the transmitter.
Install 3 AAA batteries as shown and reattach cover.
1. Confirm the valve is not in REMOTE mode.
• If the valve is producing Error Code 8 and in RE-
MOTE mode, the valve is defective and should be
replaced.
2. Once steps 1-3 in OPERATION are completed,
receiver/valve and transmitter are now ready. Press
any button on transmitter for recognition process to
occur between the receiver/valve and transmitter.
• If the valve is in LOCAL mode and producing Error
Code 8, then go to the next step.
3. Use functions as described in TRANSMITTER sec-
tion.
2. Slide the Remote/Local switch to REMOTE and
teach the valve a transmitter (refer to Item 6, page
29). The Error Code will clear itself after approxi-
mately 1¹⁄₂ minutes and return to normal operation.
20010667
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
LED Count
Service Action
8
7
Replace valve
Confirm stepper motor connection
exists
5
Confirm fan connection exists and
works
4
3
2
Confirm gas type; jumper in place
Replace thermopiles
Turn fan ON
NOTE: Some keys are not active.
Auto Path
If the manual switch is
set to REMOTE, press
the mode button to
display AUTO on the
transmitter. Does the
transmitter display the
room and temperature
setting?
Move switch
from LOCAL to
REMOTE. Press
any key within 30
seconds.
Yes
If the setting is above
room temperature on
the transmitter, does the
main valve and fan turn
on?
No
No
Yes
If the setting is below
room temperature on
the transmitter, does
the main valve and fan
turn off?
Turn pilotstat knob
to OFF to turn valve
completely off
20010667
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Comfort Valve System Control Sequence of Operation with Transmitter
Set manual switch
to local or remote
Five minute wait
period
Light pilot burner
Yes
Did the LED stop
blinking?
Review LED fail-
ure analysis
Release pilotstat
knob
Cycle switch
once and leave in
remote. Press any
key on transmit-
ter for recognition
operation
Yes
Choose Local or
Remote path. Set
switch to manual or
remote
Turn pilotstat knob
from PILOT to ON
On Path
Local Path
If the manual switch
is set to REMOTE,
press the mode but-
ton to display “ON”.
Does transmitter con-
trol the main burner
and fan?
If manual switch is
set to LOCAL, did
main burner light?
Move switch from
local to remote.
Press any key on
transmitter. Move
switch back to
local
Move switch from
manual to remote.
Press any key on
transmitter.
Yes
No
Transmitter con-
trols fan
Yes
Does transmitter
change levels of
flame height, fan
speed and set
temperature?
No
Yes
Turn pilotstat knob
to PILOT to turn
off main burner
Yes
Set levels of flame
height and fan to
“0” to shut off main
burner and fan
Turn pilotstat knob
to OFF to turn
valve completely
off
Turn pilotstat knob
to OFF to turn
valve completely
off
20010667
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Troubleshooting - Honeywell VS8421
Remove Window Frame Assembly Before Service Work
CHECK
START
• Supply Line Hooked Up
• Shutoff Valve Open
NO
Gas Supply On
YES
• Lockout Has Engaged. Wait 60
Seconds And Try Again.
▼
• For Spark At Electrode While
Depressing Piezo
Pilot Lights With Piezo
Ignitor
NO
1/8" Gap To Pilot Hood Needed.
• All Wiring Connections
• Replace Piezo Ignitor
YES
• For Air In The Lines
• Thermopile Needs A Min.
325mv. Adjust Pilot Flame
Height.
▼
• All Wiring Connections
• Replace Thermopile
Pilot Stays Lit
NO
• Thermocouple Needs A Min. Of
14mv
YES
• Valve Is Turned On
• Wall Switch Is Not Turned On.
Watch For Grounded Wires!
▼
Pilot Lights Main Burner
NO
• Thermopile Needs A Min. 325mv.
• Plugged Burner Orifice
• Defective Valve. Turn To Pilot,
Meter Should Read Greater Than
100mv. If Not, Replace.
YES
▼
SYSTEM OK
20010667
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Troubleshooting the Gas Control System
SIT NOVA 820 Millivolt Valve
NOTE: Before trouble shooting the gas control system, be sure external gas shut off is in the “On” position.
WARNING: Before doing any gas control service work, remove glass front.
SYMPTOM
1. Spark ignitor will not light
POSSIBLE CAUSES
A. Defective or misaligned
electrode at pilot.
CORRECTIVE ACTION
Using a match, light pilot. If pilot lights, turn off
pilot and push the red button again. If pilot will not
light - check gap at electrode and pilot-
should be 1/8” to have a strong spark.
B. Defective ignitor
(Push button)
Push Piezo Ignitor Button. Check for spark at
electrode and pilot. If no spark to pilot, and elec-
trode wire is properly connected, replace ignitor.
Check pilot flame. Must impinge on thermo-
2. Pilot will not stay lit after
carefully following
A. Defective pilot generator
(thermocouple), remote wall couple/thermopile. Note: this pilot burner
lighting instructions.
switch
assembly utilizes both-a thermocouple and a ther-
mopile. The thermocouple operates the main valve
operation (On and Off). Clean and or adjust pilot for
maximum flame impingement on thermopile and
thermocouple.
B. Defective automatic valve
Turn valve knob to “Pilot”. Maintain flow to pilot;
milivolt meter should read greater than 10 mV.
If the reading is okay and the pilot does not stay on,
replace the gas valve. Note: An interrupter block
(not supplied) must be used to conduct this test.
Check wall switch and wires for proper connections
Jumper wire accross terminals at wall switch, if
burner comes on, replace defective wall switch. If
okay, jumper wires across wall switch wires at valve,
if burner comes on, wires are faulty or connections
are bad.
3. Pilot burning, no gas to
main burner
A. Wall switch or wires
defective
B. Thermopile may not be
generating sufficient
millivoltage
1. Be sure wire connections from thermopile at gas
valve terminals are tight and thermopile is fully
inserted into pilot bracket.
2. One of the wall switch wires may be grounded.
Remove wall switch wires from valve terminals if
pilot now stays lit, trace wall switch wiring for
ground. May be grounded to fireplace or gas
supply.
3. Check thermopile with millivolt meter. Take
reading at thermopile terminals of gas valve.
Should read 250-300 millivolts (minimum 150)
while holding valve knob depressed in pilot
position and wall switch “Off”. Replace faulty
thermopile if reading is below specified minimum.
Check burner orifices for debris and remove.
Turn valve knob to “On”, place wall switch to “On”
millivolt meter should read greater than 100 mV. If
the reading is okay and the burner does not come
on, replace the gas valve.
C. Plugged burner orifice.
D. Defective automatic valve
operator.
4. Frequent pilot outage
problem.
A. Pilot flame may be too low
Clean and/or adjust pilot flame for maximum flame
or blowing (high) causing the impingement on thermopile and thermocouple.
pilot safety to drop out.
B. Possible blockage of the
vent terminal.
Check the vent terminal for blockage (recycling the
flue gases)
20010667
37
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Troubleshooting the Gas Control System
START
•TURN GAS SUPPLY OFF
• TURN ON/OFF SWITCH
TO CALL FOR HEAT "ON"
NO
CHECK: • LINE VOLTAGE (120VAC)
• LOW VOLTAGE TRANSFORMER (19.5 minimum VAC)
• ON/OFF SWITCH
• WIRING CONNECTIONS
POWER TO MODULE
(24V NORMAL)
UNPLUG IGNITION LEAD
YES
NO
AND CHECK SPARK
AT MODULE
(24VAC normal)
NO
• REPLACE MODULE
SPARK ACROSS
IGNITOR SENSOR GAP
SPARK OK?
YES
YES
• CHECK IGNITION CABLE GROUND WIRING, CERAMIC INSULATOR
AND GAP. CORRECT AS NECESSARY
• CHECK BOOT OF IGNITION CABLE FOR SIGNS OF MELTING OR
BUCKLING. TAKE PROTECTIVE ACTION TO SHIELD
CABLE AND BOOT FROM EXCESSIVE TEMPERATURES.
NO
• TURN GAS ON
PILOT BURNER LIGHTS?
YES
• CHECK THAT ALL MANUAL GAS VALVES ARE OPEN, SUPPLY TUBING
AND PRESSURES ARE GOOD, AND PILOT BURNER ORIFICE
IS NOT BLOCKED.
• CHECK ELECTRICAL CONNECTIONS BETWEEN MODULE AND
PILOT OPERATOR ON GAS CONTROL.
• CHECK FOR 24VAC ACROSS PV-MVPV TERMINALS ON MODULE IF
VOLTAGE IS OKAY, REPLACE GAS CONTROL IF NOT, REPLACE
MODULE.
NO
SPARK STOPS WHEN
PILOT IS LIT?
NOTE: IF S8600B GOES INTO LOCKOUT, RESET SYSTEM.
• CHECK CONTINUITY OF IGNITION CABLE AND GROUND WIRE.
• CLEAN FLAME ROD
YES
• CHECK ELECTRICAL CONNECTIONS BETWEEN FLAME ROD & MODULE.
• CHECK FOR CRACKED CERAMIC FLAME ROD INSULATOR.
• CHECK THAT PILOT FLAME COVERS FLAME ROD AND IS STEADY BLUE
• ADJUST PILOT FLAME.
• IF PROBLEM PERSISTS, REPLACE MODULE.
• CHECK FOR 24VAC ACROSS MV-MVPV TERMINALS IF NO
VOLTAGE, REPLACE MODULE.
NO
NO
MAIN BURNER LIGHTS?
YES
• CHECK ELECTRICAL CONNECTIONS BETWEEN MODULE AND GAS
CONTROL. IF OKAY, REPLACE GAS CONTROL, OR GAS CONTROL
OPERATOR.
NOTE: IF S8600B GOES INTO LOCKOUT, RESET SYSTEM
SYSTEM RUNS UNTIL
ON/OFF SWITCH IS IN
"OFF" POSITION
•
CHECK FOR CONTINUITY OF IGNITION CABLE AND GROUND WIRE.
NOTE: IF GROUND IS POOR OR ERRATIC, SHUTDOWN MAY OCCUR
OCCASIONALLY EVEN THOUGH OPERATION IS NORMAL AT THE TIME
OF CHECKOUT.
YES
•
•
CHECK THAT THE PILOT FLAME COVERS FLAME ROD AND IS STEADY
AND BLUE.
TROUBLESHOOTING
ENDS
IF CHECKS ARE OKAY, REPLACE MODULE.
20010667
38
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Troubleshooting the Gas Control System
SIT 822 Valve with Synetek Electronic Control
Operating Diagram
Abnormal Operation
Normal Operation
ON/OFF Switch Closed?
YES
5 sec Inter-Trial Delay
LED: Steady Flash?
NO
Safe Start Check On?
YES
Lockout: Flame detected out of sequence
Reset by interrupting ON/OFF switch or
power for 10 sec
0 Sec Purge
LED: 5 Flashes?
Reverse power cord polarity
Ignition Trial: 30 sec Spark ON
Pilot Valve ON. Has Flame
been Detected within 30 sec?
LED: 2 Flashes?
Reset by interrupting ON/OFF
switch for power for 10 sec
NO
YES
Pilot, Valve OFF, Spark OFF
Have three ignition trials been completed?
NO
Spark Off. Main Valve ON.
Pilot Flame Continuously
Monitored
LED: 3 Flashes?
Lockout: Flame Loss
Reset by interrupting ON/OFF switch or
power for 10 sec
Pilot Flame Sense OK?
NO
Main Valve OFF, Spark ON
Has flame been detected within 30 sec?
YES
ON/OFF Switch Opened?
YES
NO
Have three pilot flame losses been
detected?
YES
Pilot and Main Valve OFF?
YES
0 sec Post Purge?
Heating Cycle Complete LED:
OFF
20010667
39
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Conversions must be completed by qualified personnel
2. Insure the rubber gasket (D) is properly positioned
and install the new HI/LO pressure regulator assem-
bly to the valve using the new screws (E) supplied
with the kit. Tighten the screws securely. (Ref. torque
= 25 in/lb) (Fig. 65)
3. Install the enclosed conversion label (F) to the valve
body where it can easily be seen. (Fig. 65)
Valve conversion is complete.
Fuel Conversion Instructions
To convert the DV360/580 units for use with a different
gas follow these instructions. Before proceeding, turn
control knob on valve to “OFF” and turn gas supply
OFF. Turn OFF any electricity that may be going to the
appliance.
CAUTION: Logs may be HOT! Allow to cool before
proceeding.
1. Open louvre assembly bottom to gain access to
valve. Remove window frame assembly. (See “Win-
dow Frame Assembly Removal”, Page 24, Fig. 47)
E
2. Remove logs if previously installed.
Honeywell Valve
1. Remove cap from HI/LO knob. This can be accom-
plished by lifting the plastic cap off the screw. (Fig.
63)
2. Remove the screw from center of HI/LO knob with
small screwdriver turning counterclockwise. (Fig. 63)
3. Insert conversion screw supplied in conversion kit.
Blue for natural gas, red for LP.
D
4. Tighten screw, replace cap.
F
Cap
FC108
Lift Open
Fig. 65 Replace regulator.
Burner Orifice Conversion
DV360
Hi/Lo
Knob
Remove Center Screw
CO100
1. Remove the screws that secure the fettle and the
burner tube assembly, located behind the burner
tube assembly. Remove the four (4) screws that se-
cure the burner housing assembly to the base pan at
the right and left end of the burner housing assem-
bly. (Fig. 66)
Fig. 63 Remove center screw from Hi/Lo knob.
NOVA SIT820 Valve
1. Using the TORX T20 bit, remove and discard the
three (3) pressure regulator mounting screws (A),
pressure regulator tower (B) and the spring and
diaphragm assembly (C). (Fig. 64)
Pilot Location
Burner Housing
Assembly
A
Remove
Screws
B
C
Burner Tube
Assembly
CO129
Remove Screws
Fig. 66 Remove screws holding burner housing assembly
and burner tube assembly.
2. Remove the fettle and the burner tube assembly.
Slide the burner housing assembly to the right and
up to free the orifice.
FC107
Fig. 64 Remove mounting screws, pressure regulator tower
and spring and diaphragm assembly.
20010667
40
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
3. Using a 1/2” open end wrench remove the orifices.
(Fig. 67)
Gasket
Burner Housing
Mixing Tube
Front Burner Orifice
(Refer to Table on
Page 42)
Natural
Rear Burner
Orifice
(Refer to Table
on Page 42)
CO130
Propane
Fig. 67 Burner orifice replacement.
4. Converting LP to NG, remove bracket/gasket as-
sembly by unfastening the screw which secures the
bracket to the burner tray base. Discard bracket and
refasten the screw into the hole. (Fig. 67a)
CO131
Fig. 68 Replace mixing tube and gasket.
8. Reassemble the burner housing assembly, the
burner tube assembly and the fettle in reverse order.
Converting NG to LP, assemble the bracket/gas-
ket assembly to the burner tray assembly base by
unfastening the screw on the tray to the right side of
the orifice. Slide the bracket/gasket assembly over
the fitting on the manifold toward the back with the
gasket to the right. Secure the bracket/gasket as-
sembly using the screw removed earlier. (Fig. 67a)
DV580
1. Remove manifold mounting screw from burner. (Fig.
69)
2. Remove burner orifice from manifold assembly using
3/8” wrench. (Fig. 70)
3. Install conversion orifices in place of orifices just
removed.
Manifold Assembly
Burner Pan
Pilot Location
LP Bracket/Gas-
ket Assembly - in
place for use with
LP Gas; remove
for use with Natu-
ral Gas
Manifold Mounting
Screw
Screw
Log Support
(DV580)
Orifice
CO101a
Fig. 69 Remove manifold assembly.
CO132
Rear Burner Orifice:
(Refer to Conversion Kit Orifice
Chart)
Fig. 67a LP bracket/gasket assembly.
5. Replace the orifices according to the table on Page
42.
6. Replace the mixing tube on the burner housing by
removing the two (2) screws that secure the mixing
tube to the burner housing assembly. Remove the
old gasket behind the mixing tube. (Fig. 68) NOTE:
The mixing tube for propane gas has only two
bimetallic springs that are in the closed position
at cold start. The mixing tube for natural gas has
two spring/shutter collar assemblies that are in
the closed position at cold start. Make sure the
correct mixing tube is used for conversion.
7. Use the new gasket supplied in the conversion kit
and proper mixing tube and replace in reverse order.
Front Burner Orifice:
(Refer to Conversion Kit
Orifice Chart)
CO102a
Fig. 70 Burner orifice replacement.
4. Remove air shutters from burner pan by removing
shutter retaining screw then air shutter. (Fig. 71)
5. Replace only the rear air shutters.
Natural Gas: Rear air shutter, fully open.
Front air shutter, fully open.
LP:
Rear air shutter, fully open.
Front air shutter, fully open.
20010667
41
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
moval Section” Page 24, Fig. 47)
2. Remove logs if previously installed. CAUTION: Logs
may be hot!
Burner Pan
Shutter
Retaining
Screw
3. Remove and replace plug on lower right hand side of
the valve; Red for LP and blue for NG. (Fig. 74)
4. Remove motor top cap. Depress and turn center
plunger until arrow points to correct screw. Red for
LP and Blue for NG. NOTE: Plunger will “snap” into
NG position when arrow is close to blue screw. It will
not “snap” at LP (Red) position. (Fig. 75)
Air
Shutter
Front View
CO103
Fig. 71 Remove air shutter from burner pan.
6. Re-install manifold to burner pan.
Pilot Orifice Conversion
Motor Top Cap
Piezo Ignitor
NOTE: It is not necessary to remove the pilot tube for
conversion.
1. Remove pilot hood by lifting up. (Fig. 72)
2. Remove pilot orifice with Allen wrench. (Fig. 73)
3. Install conversion pilot orifice.
OFF
•
4. Re-install pilot hood and be sure to align with index
tab. Installation is complete.
Pilot Hood
LED
Local/
Remote Switch
Pilotstat
Knob
Plug
Antenna
Pilot
Bracket
FP1037
Fig. 74 Comfort control valve.
CO105a
Motor Top Cap
Center
Plunger
Fig. 72 Remove pilot hood.
Index Tab
Allen Wrench
Blue - NG
Red - LP
FP1037b
Fig. 75 Depress and turn center plunger.
Snap Ring
Burner Orifice Conversion
DV360
CO106a
1. Remove the screws that secure the fettle and the
burner tube assembly, located behind the burner
tube assembly. Remove the two (2) screws that
secure the burner housing assembly to the base pan
at the right end of the burner housing assembly. (Fig.
66)
2. Remove the fettle and the burner tube assembly.
Slide the burner housing assembly to the right and
up to free the orifice.
Fig. 73 Remove pilot orifice.
Fuel Conversion Instructions
Honeywell Comfort Control Valve ONLY
WARNING: The conversion must only be
undertaken by a qualified, certified gas ap-
pliance installer.
Installation Precautions
3. Using a 1/2” open end wrench remove the orifices.
(Fig. 67)
Before proceeding, turn control knob on valve to OFF
and turn gas supply OFF. Turn OFF any electricity that
may be going to the appliance. CAUTION: Logs may
be hot!
4. Converting LP to NG, remove bracket/gasket as-
sembly by unfastening the screw which secures the
bracket to the burner tray base. Discard bracket and
refasten the screw into the hole. (Fig. 67a)
Converting NG to LP, assemble the bracket/gas-
ket assembly to the burner tray assembly base by
Conversion Procedure
1. Open bottom grille to gain access to valve. Remove
glass door. (Refer to “Window Frame Assembly Re-
20010667
42
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
unfastening the screw on the tray to the right side of
the orifice. Slide the bracket/gasket assembly over
the fitting on the manifold toward the back with the
gasket to the right. Secure the bracket/gasket as-
sembly using the screw removed earlier. (Fig. 67a)
5. Replace the orifices according to the table on Page
42.
2. Remove pilot orifice with needlenose pliers. (Fig. 77)
3. Install conversion pilot orifice.
4. Reinstall pilot hood. Be sure to align pilot hood with
index marks.
6. Replace the mixing tube on the burner housing by
removing the two (2) screws that secure the mixing
tube to the burner housing assembly. Remove the
old gasket behind the mixing tube. (Fig. 68) NOTE:
The mixing tube for propane gas has only two
bimetallic springs that are in the closed position
at cold start. The mixing tube for natural gas has
two spring/shutter collar assemblies that are in
the closed position at cold start. Make sure the
correct mixing tube is used for conversion.
7. Use the new gasket supplied in the conversion kit
and proper mixing tube and replace in reverse order.
8. Reassemble the burner housing assembly, the
burner tube assembly and the fettle in reverse order.
Pilot Hood
Index
Marks
Pilot
Bracket
CO105
Fig. 76 Remove pilot hood.
Pilot
Orifice
DV580
1. Remove manifold mounting screw from burner. (Fig.
69)
2. Remove burner orifice from manifold assembly using
3/8” wrench. (Fig. 70)
3. Install conversion orifices in place of orifices just
removed.
CO106
Fig. 77 Remove pilot orifice.
4. Remove air shutters from burner pan by removing
shutter retaining screw then air shutter. (Fig. 71)
5. Replace only the rear air shutters.
Natural Gas: Rear air shutter, fully open.
Front air shutter, fully open.
5. Turn the gas supply valve and gas valve on and test
for leaks. Use a 50/50 solution of liquid soap and
water to test for leaks at gas fittings and joints. Apply
water/soap solution with brush only - do not over ap-
ply. NEVER test with an open flame.
LP:
Rear air shutter, fully open.
Front air shutter, fully open.
6. Follow procedure on rating plate to light the pilot.
Check for leaks.
6. Re-install manifold to burner pan.
7. Turn main burner on and check for leaks.
Pilot Orifice Conversion
NOTE: It is not necessary to remove the pilot tube for
8. Install logs. Refer to Page 25 for proper log place-
ment.
conversion.
Installation complete.
1. Loosen pilot hood turning counterclockwise using a
7/16” wrench. (Fig. 76)
Table 1 Injector Orifice Size Matrix
Conversion to Natural Gas
Burner Orifice
Input (BTU/hr)
Kit #
20010751
Model
DV360RP/RFP
Front
#53
Part #
20007347
Rear
#43
Part #
30000512
Minimum Maximum
18,500
30,000
(.0595”)
(.089”)
Conversion to LP
Burner Orifice
Input (BTU/hr)
Kit #
20010752
20011025
Model
DV360RN/RFN
DV360EN
Front
#64
Part #
20010935
(.036”)
Rear
#54
Part #
20000130
(.055”)
Minimum Maximum
17,000
30,000
20010667
43
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Maintenance
Burner and Burner Compartment
To obtain proper operation, it is imperative that the pilot
and burner’s flame characteristics are steady, not lifting
or floating.
It is important to keep the burner and the burner com-
partment clean. At least once per year the logs and lava
rock/ember material should be removed and the burner
compartment vacuumed and wiped out. Remove and
replace the logs as per the instructions in this manual.
Typically, the top 3/8” or 1/2” of the thermopile should
be engulfed in the pilot flame. (Fig. 78)
To adjust pilot burner; (by qualified service technician)
1. Remove pilot adjustment cap.
Always handle the logs with care as they
are fragile and may also be hot if the fire-
place has been in use.
2. Adjust pilot screw to provide properly sized flame.
3. Replace pilot adjustment cap.
FK24/FK12 Fan Assembly
The primary air shutter is set at factory and should only
be adjusted, if necessary, by a qualified service techni-
cian.
The fan unit requires periodic cleaning. At least once
per month in the operating season, open the lower lou-
vre panels and wipe or vacuum the area around the fan
to remove any build up of dust or lint.
PSE Pilot
Brass Trim
3/8” - 1/2”
(10 - 13 mm)
Clean the brass trim pieces using a soft cloth lightly
dampened with lemon oil. Do not use water or house-
hold cleaners on any brass components.
Contact your local representative to arrange an annual
service program.
SIT Pilot
F584-703
Cleaning the Standing
Pilot Control System
Fig. 78 Correct pilot flame appearance.
The burner and control system consists of
• burner tube • gas orifice
• pilot assembly • thermopile
• millivolt gas valve
Most of these components may require only an oc-
casional checkup and cleaning and some may require
adjustment. If repair is necessary, it should be per-
formed by a qualified technician.
Logs May Be HOT!!
1. Turn off pilot light at gas valve side.
2. Let fireplace cool if it has been running.
3. Remove window frame assembly. (Refer to Window
Frame Assembly Removal section)
4. Remove logs.
5. Vacuum burner compartment especially around
orifice primary air openings.
6. Visually inspect pilot. Brush or blow away any dust
or lint accumulation.
7. Reinstall logs.
8. Ignite pilot - Refer to Lighting Instructions.
9. Reinstall window frame assembly.
20010667
44
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
1. DV360
1 DV580
1a
1c
5
1c
3a
4
1e
1b
1i
3a,b
1h
1j
1g
1b
1h
6
12a
1e
1d
2
1f
6
1a
7a
12
7b
10
18
8
15
20
13
14
9a
11
21
9b
23
17
22a-d
16
33
27
19 a/b
32
26a,b
34
24 a/b
35a/b
36
OFF
28
46
25 a/b
37
38
30
29
39
41
40
31
48
52
42
51
47
49
53
50
54
61
56
55
58
59a,b
57a,b
62
60a,b
64
66
OF
•
65a,b
63
68
LED
66
67
70a
79
72a,b
78
71a,b
69
77
70b
HI
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,
without notice.
DV360/580
20010667
45
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
DV360/580
Ref. Description
1. Log Set
(continued)
DV360
20010671
20010673
20010672
20010675
--
20010676
--
20010677
20010674
20000376
51915
DV580
10007545
10007540 (E9)
10007541 (E10)
10007539 (E8)
10007543 (E12)
10007544 (E13)
10007542 (E11)
--
1a. Log Front Left
1b. Log Front right
1c. Log Rear
1d. Log Top Left
1e. Log Top Right
1f. Log Top Center Left
1g. Log Top Center
1h. Log Overlay
1i. Volcanic Rock
--
20000376
51915
1j. Ember (Package)
2. Lava Rock (Burner)
--
57897
3a. Burner Housing Assy - Nat.
3b. Burner Housing Assy - LP
4. Burner Tube Assy.
20011467
20011322
20010580
57803
20010601*
--
10007533
--
--
5. Ceramic tile (single)
10002165
10002492
10007992
10007993
10007994
10007995
10007996
20002369
10000992
10007538
--
6. Manifold Assembly (* Refer to Note on Page 45)
7a. Ceramic Hearth Panel (Left)
7b. Ceramic Hearth Panel (Right)
8. Ceramic Panel (Rear)
9a. Ceramic Panel (Left Side)
9b. Ceramic Panel(Right Side)
10. Glass with Gasket
11. Gasket Glass
12. Door Frame Assy
12a. Door Assy
13. Clamp Frame Window
14. Trim Frame Window (Pb) (w/two magnets)
15. Louvre Assembly Top
16. Louvre Assembly Bottom
17. Bottom Louvre Hinge
18. Deflector Top
19a. LP Valve Conversion - Red
19b. Natural Valve Conversion - Blue
20. Grate Assembly
--
--
--
--
--
--
--
20002622
54174
57483
10000039
10000040
52356
54174
20002072
20002380
20002381
52356
20002287
20000550
20000572
10007537
--
20002540
20002150
20002958
20002498
51842
54364
20000550
20000572
--
20010490
20010935
20007347
20000130
30000512
51842
21. Fettle
22a. Orifice - Front Burner - LP
22b. Orifice - Front Burner - Nat.
22c. Orifice - Rear Burner-LP
22d. Orifice - Rear Burner-Nat
23. Switch On/Off
24a. Valve - Honeywell VS8421 - Nat.
24b. Valve - Honeywell VS8421 - LP
25a. Valve - SiT 820 - Nat.
25b. Valve - SIT 820 - LP
26a. Pilot Assembly - Nat.
26b. Pilot Assembly - LP
--
--
10001782
10001759
52677
52678
10002264
10002265
20010563
20010645
10002264
10002265
20010667
46
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
DV360/580
(continued)
Ref. Description
DV360
10001297
57886
DV580
10001297
57886
27. Electrode Ignitor w/Cable
28. Nut Electrode
29. Pilot tube 1/8” x 24” long w/fittings (SIT Pilot)
30. Thermocouple - RN/RP
31. Cable Ignitor - RN/RP
32. Thermopile - RN/RP
10001296
53373
53194
10001296
53373
53194
51827
51827
33. Pilot Top Convertible
34. Hood Pilot 3 way
35a. Pilot Orifice #65 (Nat.)
35b. Pilot Orifice #35 (LP)
36. Ignitor Piezo
37. Air Shutter (Nat.)
38. Fan w/ Bracket (FK24)
39. Electrical Cord (6ft.)
10002266
10002385
10002268
10002269
20000062
--
10002266
10002385
10002268
10002269
20000062
10007355
54103
54103
51865
51865
40. Fan Temp. Sensor
51704
51704
41. Speed Control
51738
51738
42. Speed Control Knob
51882
51882
43. Remote Switch Kit (Not Shown)
44. Piezo Ignitor Replacement Kit (Not Shown)
45. Ceramic Refractory Lining Kit (Optional) (Not Shown)
46. Shield Heat Pilot
47. Plate Relief w/Gasket Assembly Burner Tray
48. Firestop
53875
53875
20000062
Refer to Page 47
--
20000062
GACA4P0
10007518
10004192
52523
--
52523
49. Zero Clearance Sleeve
50. Plate Cover Air Inlet Ass’y
51. Gasket Plate Air Inlet
52. Flue Cover Plate
53. Flue Cover Gasket
54623
54623
10002766
10002449
10002298
10002233
10004933
10002237
20003561
20003719
20003720
20002400
20000908
20000907
20002266
20002268
20002047
20002541
10003279
10000506
10001006
10001007
20010622
10006154
10002429
20002461
10002449
10002298
20002391
20002481
10002237
20003561
20003719
20003720
20002400
20000908
20000907
20002266
20002268
20002047
20002541
10003279
n/a
54. Flue Pipe Ass’y
55. Gasket Plate Cover Flue Pipe
56. Antennae HW 395783-1 RFN/RFP Valve
57a. RF Valve 8310E - Natural
57b. RF Valve 8310E - LP
58. Thermopile - RF Valves
59a. Pilot Orifice - Natural - RF
59b. Pilot Orifice - LP - RF
60a. Pilot Assembly - Natural (3 Way) RF
60b. Pilot Assembly - LP (3 Way) RF
61. Transmitter
62. Cord Set
63. Pilot Tube 1/8” x 24” long w/Fittings (PSE Pilot)
64. Refractory Bay39 Set
65a. Regulator Head (Nat.)
65b. Regulator Head (LP)
66. Bracket Rear Log
67. Gasket Assy. Burner Base
68. Plate Relief w/Gasket Assy.
10001006
10001007
10007535
10007528
10002862
20010667
47
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
DV360/580
(continued)
Ref. Description
DV360
7522409
20000005
10007939
--
DV580
7522409
20000005
--
57884
57883
10002387
10002388
57885
57899
--
69. Transformer EN/EP
70a. Ignitor Module Honeywell EN/EP
70b. Ignition Control Synetek (EN)
71a. Valve - SIT 822 - EN
71b. Valve - SIT 822 - EP
--
72a. Pilot Assembly SIT Top Conv. - EN
72b. Pilot Assembly SIT Top Conv. - EP
73. Sensing Electrode w/Cable EN/EP (not shown)
74. Wire Harness, Honeywell EN/EP (not shown)
75. Tubing 3/8” OD Aluminum
76. Nut 3/8” ID Brass, Compression
77. Wire Harness (EN) Synetek (low voltage)
78. Wire Harness (EN) Synetek
10002387
10002388
57885
57899
20010564
7523136
10008139
10008140
10008298
--
--
--
--
79. Electrical Cord (6ft) Ignition Control
*NOTE: For DV360, when ordering Manifold Assembly, also order #75 (qty 1) and #76 (qty 2).
Fuel Conversion Kits
Natural Gas to LP
DV360RN/EN/RFN
DV580RN/EN
DV580RFN
Kit # 20010752
Kit # 10007997
Kit # 10008274
LP to Natural Gas
DV360RP/EN/RFP
DV580RP/EP
Kit # 20010751
Kit # 10007998
Kit # 10008275
DV580RFP
20010667
48
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Optional Accessories
Method A
Route the 6’ (1.8m) lead fitted to the unit to a conve-
niently located wall socket.
Method B
Fan Kits
FK12 Fan Assembly
1. Open louvre assembly bottom.
2. Install FK12 fan in back of unit between hearth sup-
ports. (Fig. 79)
If the EB-1 receptacle box (Pt. #ZA1200) was cor-
rectly connected when the unit was installed, the
fan lead can be directly plugged into the EB-1 plug
socket.
3. Secure fan on velcro strips.
4. Power to the fan can be supplied by plugging the
supply lead into a conveniently located wall socket
or by using a hard-wired EB-1 connector box.
5. Whether wiring directly to the fan junction box (Op-
tion A) or into the EB1 (electrical box, Option B) first
ensure cable is secured using box connector.
5. Be sure fan motor does not touch hearth supports.
The fireplace, when installed must be elec-
trically connected and grounded in accor-
dance with local codes, with the current
CSA C22.1 Canadian Electrical Code or for
US installations, follow local codes and
the National Electrical Code, ANSI/NFPA
No. 70.
Cold Air Box
Side View
Front of
Unit
Hard (Direct) Wire Hook Up
Hearth Pan
First connect ground wire to ground stud located on
the base of either box. Black wire from supply should
connect to the variable speed switch. Alternate speed
switch wire connects to temperature sensor. Alternate
lead from sensor connects to fan. Alternate fan lead
connects back to the white supply wire. (Fig. 81)
Base Pan
FK12 Fan
FP1004
Fig. 79 FK12 Fan Kit placement.
Any electrical rewiring of this fan must be
completed by a qualified electrician.
FK24 Fan Assembly
Fan specifications: 120 volt, 60 Hz, .75 Amp.
Turn off all power before hook up.
This fan does not need regular maintenance, however
periodic cleaning is required. Check the area under the
control door and in front of the fan and wipe or vacuum
at least once a month during the operating season.
Should this fan require servicing, the power supply must
be disconnected.
Electrical Box
Heat Sensor
Fan
The FK24 comes with the electrical cord attached.
A
E
1. Slide fan assembly from the left side into the fire-
place opening, line up mounting holes with screw
studs on back of fireplace and fasten with #10 - 24
hex nuts. (Fig. 80)
Fan Speed
Switch
Valve
Gas Line
FP1026
Fig. 80 FK24 fan placement.
2. Install thermal sensor on bottom of firebox using #10
- 24 hex nuts.
Fan
Temperature
Sensor
3. (Option A) - Place electronic fan speed control box
on bottom of fireplace base, lining up mounting holes
with screw studs. Fasten fan speed control box with
#10 - 24 hex nuts.
Speed
Control
Black
White
Ground
(Option B) - The speed control can be installed in an
electrical box at normal wall switch height for conve-
nient access.
FP1025
Fig. 81 FK24 fan wiring.
4. The power supply may be connected in 2 ways:
20010667
49
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Remote Controls
Optional remote control units are available to control
different functions of the appliance.
Rear Ceramic Panel
Back of
Firebox
Model
RC1
Functions Controlled
ON/OFF
RC2
IMTFK
ON/OFF and Temperature
Wall mounted thermostat control
Burner
Ceramic Refractory Panels
Rear Log
Support
Ceramic refractory panels are available to line the fire-
box area.
H102
Unit
Kit Model
Fig. 83 Rear ceramic panel placement.
DV360
DV360
DV360
DV360
DV580
DV360CRSS
DV360CRR
DV360CRB
DV360CRG
DV580CR
Sandstone
Red
Black
Decorative Bay Windows
The bay window kit is available for the DV360 only.
Installation
Grey
Remove the existing louvre assembly top.
Take care when handling the refractory
panels as they are fragile until held in
place and supported.
Assemble the Bay Window Kit according to the instruc-
tions supplied with the kit. (Fig. 84)
Installation Instructions
Upper Grille Assembly
1. Remove window frame assembly and logs.
2. Remove three (3) screws securing heat shield to
combustion dome. (Fig. 82)
3. Place rear ceramic panel in back of unit. (Fig. 83)
4. Place side panels.
Ceramic
Refractory
Ceramic
Refractory
5. Replace heat shield, logs and window frame assem-
bly.
Section A
Heat Shield
Heat Shield
Window
Assembly
Base Grille
Assembly
FP1194
Fig. 84 Bay window.
(3)
Screws
Decorative Frame Trims
Side View
Section A
A selection of decorative frame trim kits are available for
mounting around the outside of the appliance to en-
hance its visual effect on the room. Installation instruc-
tions for each decorative frame trim are included with
the frame trim kit. Contact your authorized distributor for
details of the trim kits and ordering information for the
trim kits applicable to this model appliance.
H103
Fig. 82 Heat shield.
20010667
50
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
Arch/Square Face Kit
for the DV360
Romanesque - Arch
41DVARFKB
41DVARFKR
41DVARFKS
Black
Rustic Bronze
Pewter
Romanesque - Square
41DVSRFKB
Black
Rustic Bronze
Pewter
41DVSRFKR
41DVSRFKS
Marquette - Arch
41DVAMTKB
Black
Rustic Bronze
Pewter
41DVAMTKR
41DVAMTKS
Marquette - Square
41DVSMTKB
Black
Rustic Bronze
Pewter
41DVSMTKR
41DVSMTKS
20010667
51
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
For Use in Mobile Homes: Model DV360RMH
This appliance may be installed as an OEM installation in a manufactured home (US only), or a mobile
home; it must be installed in accordance with the manufacturer’s instructions and the manufactured
home construction and safety standard Title 24 CFR Part 3280, or Standard for Installation in Mobile
Homes CAN/ CSA Z240 MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is sup-
plied with the appliance.
This gas fireplace should be installed by a qualified in-
staller in accordance with local building codes, and with
current CSA-B149.1 Installation codes for Gas Burning
Fireplaces and Equipment, and CAN/
7. The venting system (chimney) of this fireplace
should be checked at least once a year and if
needed your venting system should be cleaned.
8. Keep the area around your fireplace clear of com-
bustible materials, gasoline and other flammable
vapor and liquids. This fireplace should not be used
as a drying rack for clothing, nor should Christmas
stockings or decorations be hung on or around the
fireplace.
CSA Z 240.4 Canada.
A manufactured home (US only) or mobile home
OEM installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24 CFR
Part 3280, or when such a standard is not applicable,
the Standard for Manufactured Home Installations
9. Under no circumstances should any solid fuels
(wood, coal, paper or cardboard etc.) be used in this
fireplace.
ANSI/NCSBCS A225.1, or Standard for Gas Equipped
Recreational Vehicles and Mobile Housing
10. The flow of combustion and ventilation air must not
be obstructed in any way.
CSA Z240.4.
The appliance when installed, must be electrically
grounded in accordance with local codes or, in the ab-
sence of local codes, with the current National Electri-
cal Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1.
11. When the fireplace is installed directly on carpet-
ing, vinyl tile or any combustible material other than
wood, the fireplace must be installed on a metal or
wood panel extending the full width and depth of the
fireplace.
12. This fireplace requires adequate ventilation and
combustion air to operate properly.
FOR SAFE INSTALLATION AND OPERATION
PLEASE NOTE THE FOLLOWING:
CFM Corporation Model DV360RMH must
be firmly attached to the building.
1. This fireplace gives off high temperatures and
should be located out of high traffic areas and away
from furniture and draperies.
Conversion Instructions
2. Children and adults should be alerted to the hazards
of fireplace high surface temperatures and should
stay away to avoid burns or ignition of clothing.
1. Discount power to unit and shut off the gas supply.
2. Remove the window frame assembly (see ‘Window
Frame Assembly’ section).
3. Children should be carefully supervised when in the
same room as your fireplace.
3. Carefully remove the logs.
4. Under no circumstances should this fireplace be
modified. Parts removed for servicing should be
replaced prior to operating this fireplace again.
4. Remove the pilot assembly from bracket.
5. Remove the screws which are holding the burner
housing assembly in place.
5. Installation and any repairs to fireplace should be
performed by qualified installer, service agency or
gas supplier. A professional service person should
be contacted to inspect fireplace annually. More
frequent cleaning may be required due to excess lint
and dust from carpeting, bedding material, etc.
6. Remove the burner housing assembly.
7. Remove the main and front orifice and replace with
the orifice supplied in the conversion kit. Use the
small orifice size for the front burner and the bigger
orifice size for the main burner.
8. Remove the compression fitting which holds the alu-
minium tubing in the pilot assembly. This will reveal
the pilot orifice which must be replaced with the one
provided in the conversion kit.
6. Control compartments, burners and air passages
in this fireplace should be kept clean and free of
dust and lint. Make sure that the gas valve and pilot
light are turned off before you attempt to clean this
fireplace.
9a. Units with SIT valve (Refer to illustrations in the
installation instructions supplied with the kit):
20010667
52
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
a) Using a Torx T20 or slotted screwdriver, remove
and save the three pressure regulator mount-
ing screws (A), pressure regulator tower (B) and
diaphragm (C).
b) Ensure the rubber gasket (D) is properly posi-
tioned and install the new Hi/ Lo pressure regula-
tor to the valve using the new screws (E) supplied
with the kit. Tighten screws securely. (Ref. torque:
25 in-lb).
c) Install the enclosed identification label (F) to the
valve body where it can be easily seen.
9b.Units with Honeywell valve:
The Honeywell valve fitted to this unit is preset for
LP gas. It is convertible to natural gas by the instal-
lation of a color coded “conversion screw.” To insert
the conversion screw, refer to the instructions and
diagrams in the Honeywell Installation Instructions
supplied in the conversion kit packaged with the
DV360/DV580RMH unit.
10. Reassemble the fireplace in the reverse order,
except for the window frame assembly. Leave this off
until the unit has been checked for leaks and the gas
supply line has been bled.
11. After bleeding the gas line and checking for leaks
with a soap solution, replace the window frame
assembly. Fire up the unit, check for flame impinge-
ment on the logs, adjusting them if necessary. Check
the manifold and supply pressures.
NOTE: If further assistance is required, refer to
‘Troubleshooting’ and ‘Parts List’ in this manual.
20010667
53
Download from Www.Somanuals.com. All Manuals Search And Download.
DV360/580 Series Direct Vent Gas Fireplace
20010667
54
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED LIFETIME WARRANTY
PRODUCT COVERED BY THIS WARRANTY
All Vermont Castings gas stoves, gas inserts, and gas fireplaces, and all Majestic brand gas fireplaces equipped with
an Insta-Flame Ceramic Burner, or standard steel tube burner.
BASIC WARRANTY
•
Any part and/or component replaced under the provisions of this
warranty is covered for six months or the remainder of the original
warranty, whichever is longest.
CFM Corporation (hereinafter referred to collectively as the Company)
warrants that your new Vermont Castings or Majestic Gas Fireplace/
Stove is free from manufacturing and material defects for a period of
one year from the date of purchase, subject to the following conditions
and limitations.
•
This warranty is limited to the repair of or replacement of part(s) found
to be defective in material or workmanship, provided that such part(s)
have been subjected to normal conditions of use and service, after
said defect is confirmed by the Company’s inspection.
EXTENDED LIFETIME WARRANTY
•
•
The company may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding the wholesale price of the
defective part(s)
The heat exchanger, where applicable, and combustion chamber
of every Vermont Castings or Majestic gas product is warranted for
life against through wall perforation. All appliances equipped with an
Insta-Flame Ceramic Burner have limited lifetime coverage on the
ceramic burner plaque. Warrantees are made to the original owner
subject to proof of purchase and the conditions and limitations listed
on this Warranty Document
Any installation, labor, construction, transportation, or other related
costs/expenses arising from defective part(s), repair, replacement,
or otherwise of same, will not be covered by this warranty, nor shall
the Company assume responsibility for same. Further, the Company
will not be responsible for any incidental, indirect, or consequential
damages except as provided by law.
COMPONENT WARRANTY
CAST IRON: All external and internal cast iron parts are warranted for a
period of three years.
•
SOME STATES DO NOT ALLOW FOR THE EXCLUSION OR
LIMITATIONS OF INCIDENTALAND CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOUR
CIRCUMSTANCES. THIS WARRANTY GIVES YOU SPECIFIC
RIGHTSANDYOU MAYHAVE OTHER RIGHTS WHICH VARYFROM
STATE TO STATE.
Note: On porcelain enamel finished external parts and accessories
The Company offers no Warranty on chipping of enamel surfaces.
Inspect all product prior to accepting it for any damage to the
enamel.
The salt air environment of coastal areas or a high humidity
environment can be corrosive to the porcelain enamel finish. These
conditions can cause rusting of the cast iron beneath the porcelain
enamel finish, which will cause the finish to flake off.
•
•
•
•
All other warranties-expressed or implied- with respect to the product,
its components and accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
The Company neither assumes, nor authorizes any third party to
assume on its behalf, any other liabilities with respect to the sale of
this Vermont Castings or Majestic product
Dye lot variations with replacement parts and/or accessories can
occur and are not covered by warranty.
GLASS DOORS: Glass doors are covered for a period of one year.
Glass doors are not warranted for breakage due to misuse or accident.
Glass doors are not covered for discoloration or burned in stains due to
environmental issues, or improper cleaning and maintenance.
The warranties as outlined within this document do not apply to
chimney components or other non CFM Corporation accessories used
in conjunction with the installation of this product..
Damage to the unit while in transit is not covered by this warranty but
is subject to claim against the common carrier. Contact the dealer
from whom you purchased your fireplace/stove (do not operate the
appliance as this might negate the ability to process the claim with the
carrier).
BRASS PLATED PARTS AND ACCESSORIES: Brass parts should be
cleaned with Lemon oil only. Brass cleaners cannot be used. Mortar
mix and masonry cleaners may corrode the brass finish. The Company
will not be responsible for, nor will it warrant any brass parts which are
damaged by external chemicals or down draft conditions.
•
•
The Company will not be responsible for:
GAS VALVES: Gas valves are covered for a period of one year
a) Down drafts or spillage caused by environmental conditions such
as near-by trees, buildings, roof tops, hills, or mountains.
b) Inadequate ventilation or negative air pressure caused by
mechanical systems such as furnaces, fans, clothes dryers, etc.
ELECTRONIC AND MECHANICAL COMPONENTS: Electronic and
mechanical components of the burner assembly are covered for one
year. All steel tube burners are warranted for one year.
ACCESSORIES: Unless otherwise noted all components and CFM
Corporation company supplied accessories are covered for a period of
one year.
This warranty is void if:
a) The fireplace has been operated in atmospheres contaminated by
chlorine, fluorine, or other damaging chemicals.
b) The fireplace has been subjected to prolonged periods of
dampness or condensation
c) Any damages to the fireplace, combustion chamber, heat
exchanger or other components due to water, or weather damage,
which is the result of but not limited to, improper chimney/venting
installation.
CONDITIONS AND LIMITATIONS
•
This new Vermont Castings or Majestic product must be installed by
a competent, authorized, service contractor. A licensed technician, as
prescribed by the local jurisdiction must perform any installation/service
work. It must be installed and operated at all times in accordance with
the Installation and Operating instructions furnished with the product.
Any alteration, willful abuse, accident, or misuse of the product shall
nullify this warranty.
d) Any alteration, willful abuse, accident, or misuse of the product
has occurred.
•
•
This warranty is non-transferable, and is made to the original owner,
provided that the purchase was made through an authorized supplier
of the Company.
IF WARRANTY SERVICE IS NEEDED…
1) Contact your supplier. Make sure you have your
warranty, your sales receipt, and the model/serial
number of your CFM Corporation product.
2) DO NOT ATTEMPT TO DO ANY SERVICE WORK
YOURSELF.
The customer must pay for anyAuthorized Dealer in-home travel fees
or service charges for in-home repair work. It is the dealers option
whether the repair work will be done in the customer’s home or in the
dealer’s shop.
•
If upon inspection, the damage is found to be the fault of the
manufacturer, repairs will be authorized at no charge to the customer
parts and/or labor.
20010667
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Efficiency Ratings
Model
EnerGuide Ratings
Steady State (%)
D.O.E.
Fireplace Efficiency (%) Fan-OFF
Fan-ON
83
(AFUE%)
64
DV360RN
DV360RP
DV360EN
DV360EP
DV360RFN
DV360RFP
DV580RN
DV580RP
DV580EN
DV580EP
DV580RFN
DV580RFP
53
53
82
83
82
83
82
83
82
83
82
83
82
83
84
83
84
83
84
83
84
83
64
64
64
64
64
64
64
64
53
53
53
53
51.1
51.1
51.1
51.1
51.1
51.1
84
83
84
64
64
64
CFM Corporation
2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3
Download from Www.Somanuals.com. All Manuals Search And Download.
|