TOSHIBA
Satellite A40 Series
Portable Personal Computer
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC information
Product Name : Satellite A40
Model number : PSA40
FCC notice "Declaration of Conformity
Information"
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
❑ Reorient or relocate the receiving antenna.
❑ Increase the separation between the equipment and receiver.
❑ Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
❑ Consult the dealer or an experienced radio/TV technician for help.
WARNING: Only peripherals complying with the FCC class B limits may
be attached to this equipment. Operation with non-compliant peripher-
als or peripherals not recommended by TOSHIBA is likely to result in
interference to radio and TV reception. Shielded cables must be used
between the external devices and the computer’s external monitor port,
USB port, parallel port and microphone jack. Changes or modifications
made to this equipment, not expressly approved by TOSHIBA or parties
authorized by TOSHIBA could void the user’s authority to operate the
equipment. The modular cable that comes with the computer must be
used to connect a modem.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
Contact
Address:
TOSHIBAAmericaInformationSystems,Inc.
9740IrvineBoulevard
Irvine,California92618-1697
Telephone: (949)583-3000
EUDeclarationofConformity
TOSHIBA declares, that the product: PSA40* conforms to the following Standards:
SupplementaryInformation: “The product complies with the requirements of the
LowVoltageDirective73/23/EEC,theEMCDirective
89/336/EECand/ortheR&TTEDirective1999/05/
EEC.”
This product is carrying the CE-Mark in accordance with the related European
Directives.ResponsibleforCE-MarkingisTOSHIBAEurope,Hammfelddamm8,
41460Neuss,Germany.
VCCI Class B Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem warning notice
Conformity Statement
The equipment has been approved to [Commission Decision “CTR21”] for pan-
European single terminal connection to the Public Switched Telephone Network
(PSTN).
However, due to differences between the individual PSTNs provided in different
countries/regions the approval does not, of itself, give an unconditional assurance
of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first
instance.
Network Compatibility Statement
This product is designed to work with, and is compatible with the following
networks. It has been tested to and found to conform with the additional require-
mentsconditionalinEG201121.
Germany
ATAABAN005,AN006,AN007,AN009,AN010and
DE03,04,05,08,09,12,14,17
Greece
ATAABAN005,AN006andGR01,02,03,04
ATAABAN001,005,006,007,011andP03,04,08,10
ATAABAN005,007,012,andES01
ATAABAN002
Portugal
Spain
Switzerland
All other countries/regions ATAABAN003,004
Specific switch settings or software setup are required for each network, please refer
to the relevant sections of the user guide for more details.
The hookflash (timed break register recall) function is subject to separate national
type approvals. It has not been tested for conformity to national type regulations,
and no guarantee of successful operation of that specific function on specific
national networks can be given.
Download from Www.Somanuals.com. All Manuals Search And Download.
Japan regulations
Region selection
If you are using the computer in Japan, technical regulations described in the
Telecommunications Business Law require that you select the Japan region mode. It
is illegal to use the modem in Japan with any other selection.
Redial
Up to two redial attempts can be made. If more than two redial attempts are made,
the modem will return Black Listed. If you are experiencing problems with the
Black Listed code, set the interval between redials at one minute or longer.
Japan’s Telecommunications Business Law permits up to two redials on analogue
telephones, but the redials must be made within a total of three minutes.
The internal modem is approved by Japan Approvals Institute for Telecommunica-
tions Equipment.
A02-0604JP
Pursuant to FCC CFR 47, Part 68:
When you are ready to install or use the modem, call your local telephone company
and give them the following information:
❑ The telephone number of the line to which you will connect the modem
❑ The registration number that is located on the device
The FCC registration number of the modem will be found on either the device which
is to be installed, or, if already installed, on the bottom of the computer outside of
the main system label.
❑ The Ringer Equivalence Number (REN) of the modem, which can vary. For the
RENofyourmodem, refertoyourmodem’slabel.
The modem connects to the telephone line by means of a standard jack called the
USOC RJ11C.
Download from Www.Somanuals.com. All Manuals Search And Download.
Type of service
Your modem is designed to be used on standard-device telephone lines. Connec-
tion to telephone company-provided coin service (central office implemented
systems) is prohibited. Connection to party lines service is subject to state tariffs. If
you have any questions about your telephone line, such as how many pieces of
equipment you can connect to it, the telephone company will provide this informa-
tion upon request.
Telephone company procedures
The goal of the telephone company is to provide you with the best service it can. In
order to do this, it may occasionally be necessary for them to make changes in their
equipment, operations, or procedures. If these changes might affect your service or
the operation of your equipment, the telephone company will give you notice in
writing to allow you to make any changes necessary to maintain uninterrupted
service.
If problems arise
If any of your telephone equipment is not operating properly, you should immedi-
ately remove it from your telephone line, as it may cause harm to the telephone
network. If the telephone company notes a problem, they may temporarily discon-
tinue service. When practical, they will notify you in advance of this disconnection.
If advance notice is not feasible, you will be notified as soon as possible. When
you are notified, you will be given the opportunity to correct the problem and
informed of your right to file a complaint with the FCC. In the event repairs are ever
needed on your modem, they should be performed by TOSHIBA Corporation or an
authorized representative of TOSHIBA Corporation.
Disconnection
If you should ever decide to permanently disconnect your modem from its present
line, please call the telephone company and let them know of this change.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fax branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person
to use a computer or other electronic device to send any message via a telephone
fax machine unless such message clearly contains in a margin at the top or bottom
of each transmitted page or on the first page of the transmission, the date and time it
is sent and an identification of the business, other entity or individual sending the
message and the telephone number of the sending machine or such business, other
entity or individual. In order to program this information into your fax modem, you
should complete the setup of your fax software before sending messages.
Instructions for IC CS-03 certified equipment
1 The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection.
The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations. Repairs to certified
equipment should be coordinated by a representative designated by the
supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connec-
tions of the power utility, telephone lines and internal metallic water pipe system,
if present, are connected together. This precaution may be particularly important
inruralareas.
CAUTION: Users should not attempt to make such connections them-
selves, but should contact the appropriate electric inspection authority,
or electrician, as appropriate.
2 The user manual of analog equipment must contain the equipment’s Ringer
EquivalenceNumber(REN)andanexplanationnoticesimilartothefollowing:
The Ringer Equivalence Number (REN) of the modem, which can vary. For the
RENofyourmodem, refertoyourmodem’slabel.
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The termina-
tion on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
3 The standard connecting arrangement (telephone jack type) for this equipment is
jacktype(s):USOC RJ11C.
The IC registration number of the modem is shown below.
Canada:1353A-L4AINT
Notes for Users in Australia and New Zealand
Modem warning notice for Australia
Modems connected to the Australian telecoms network must have a valid Austel
permit. This modem has been designed to specifically configure to ensure compli-
ance with Austel standards when the country/region selection is set to Australia.
The use of other country/region setting while the modem is attached to the
Australian PSTN would result in you modem being operated in a non-compliant
manner. To verify that the country/region is correctly set, enter the command ATI
which displays the currently active setting.
To set the country/region permanently to Australia, enter the following command
sequence:
AT%TE=1
ATS133=1
AT&F
AT&W
AT%TE=0
ATZ
Failure to set the modem to the Australia country/region setting as shown above
will result in the modem being operated in a non-compliant manner. Consequently,
there would be no permit in force for this equipment and the Telecoms Act 1991
prescribes a penalty of $12,000 for the connection of non-permitted equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes for use of this device in New Zealand
❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance
of responsibility for the correct operation of that device under all operating
conditions. In particular the higher speeds at which this modem is capable of
operating depend on a specific network implementation which is only one of
many ways of delivering high quality voice telephony to customers. Failure to
operate should not be reported as a fault to Telecom.
❑ In addition to satisfactory line conditions a modem can only work properly if:
a/ it is compatible with the modem at the other end of the call and
b/ the application using the modem is compatible with the application at the
other end of the call - e.g., accessing the Internet requires suitable
software in addition to a modem.
❑ This equipment shall not be used in any manner which could constitute a
nuisance to other Telecom customers.
❑ SomeparametersrequiredforcompliancewithTelecom’sPTCSpecifications
are dependent on the equipment (PC) associated with this modem. The
associated equipment shall be set to operate within the following limits for
compliancewithTelecomSpecifications:
a/ There shall be no more than 10 call attempts to the same number within
any 30 minute period for any single manual call initiation, and
b/ The equipment shall go on-hook for a period of not less than 30 seconds
between the end of one attempt and the beginning of the next.
c/ Automatic calls to different numbers shall be not less than 5 seconds
apart.
❑ Immediately disconnect this equipment should it become physically damaged,
and arrange for its disposal or repair.
❑ The correct settings for use with this modem in New Zealand are as follows:
ATB0(CCITToperation)
AT&G2(1800Hzguardtone)
AT&P1(Decadicdialingmake-breakratio=33%/67%)
ATS0=0 (not auto answer)
ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15
recommended)
ATS11=90(DTMFdialingon/offduration=90ms)
ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)
Download from Www.Somanuals.com. All Manuals Search And Download.
❑ When used in the Auto Answer mode, the S0 register must be set with a value
of 3 or 4. This ensures:
(a) a person calling your modem will hear a short burst of ringing before the
modem answers. This confirms that the call has been successfully
switched through the network.
(b) caller identification information (which occurs between the first and
second ring cadences) is not destroyed.
❑ The preferred method of dialing is to use DTMF tones (ATDT...) as this is
faster and more reliable than pulse (decadic) dialing. If for some reason you
must use decadic dialing, your communications program must be set up to
record numbers using the following translation table as this modem does not
implement the New Zealand “Reverse Dialing” standard.
Number to be dialed: 0 1 2 3 4 5 6 7 8 9
Number to program into computer: 0 9 8 7 6 5 4 3 2 1
Note that where DTMF dialing is used, the numbers should be entered
normally.
❑ The transmit level from this device is set at a fixed level and because of this
there may be circumstances where the performance is less than optimal. Before
reporting such occurrences as faults, please check the line with a standard
Telepermitted telephone, and only report a fault if the phone performance is
impaired.
❑ It is recommended that this equipment be disconnected from the Telecom line
duringelectricalstorms.
❑ When relocating the equipment, always disconnect the Telecom line connec-
tion before the power connection, and reconnect the power first.
❑ This equipment may not be compatible with Telecom Distinctive Alert ca-
dences and services such as FaxAbility.
NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE
CAUSES MAY INCUR A CHARGE FROM TELECOM
Download from Www.Somanuals.com. All Manuals Search And Download.
General conditions
As required by PTC 100, please ensure that this office is advised of any changes to
the specifications of these products which might affect compliance with the relevant
PTCSpecifications.
The grant of this Telepermit is specific to the above products with the marketing
description as stated on the Telepermit label artwork. The Telepermit may not be
assigned to other parties or other products without Telecom approval.
A Telepermit artwork for each device is included from which you may prepare any
number of Telepermit labels subject to the general instructions on format, size and
colour on the attached sheet.
The Telepermit label must be displayed on the product at all times as proof to
purchasers and service personnel that the product is able to be legitimately
connected to the Telecom network.
The Telepermit label may also be shown on the packaging of the product and in the
sales literature, as required in PTC 100.
The charge for a Telepermit assessment is $337.50. An additional charge of $337.50
is payable where an assessment is based on reports against non-Telecom New
Zealand Specifications. $112.50 is charged for each variation when submitted at the
same time as the original.
An invoice for $NZ1237.50 will be sent under separate cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
Optical disc drive safety instructions
NOTE: Be sure to check the international precautions at the end of this
section.
TEAC
CD-RW/DVD-ROM DW-224E
CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To
ensure proper use of this product, please read this
instruction manual carefully and retain for future
reference. Should the unit ever require maintenance,
contact an authorized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
CERTIFICATION:THIS
PRODUCT COMPLIES WITH
DHHS RULES 21 CFR CHAPTER
1, SUBCHAPTER JAPPLICABLE
ATDATEOFMANUFACTURE.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
TEACCORPORATION
3-7-3 NAKA-CHO,
MUSASHINO-SHI
TOKYO,JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Multi DV-W22E
CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
CERTIFICATION:THIS
PRODUCT COMPLIES WITH
DHHS RULES 21 CFR CHAPTER
1, SUBCHAPTER JAPPLICABLE
ATDATEOFMANUFACTURE.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
TEACCORPORATION
3-7-3 NAKA-CHO,
MUSASHINO-SHI
TOKYO,JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA
DVD-ROM SD-C2612
CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
PRODUCT IS CERTIFIED BY THE
MANUFACTURER TO COMPLY
WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT
THE DATE OF MANUFACTURE.
MANUFACTURED:
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME
MINATO-KU, TOKYO 105-8001,
JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD-R/-RW SD-R6112
CAUTIONS: 1. The DVD-R/-RW drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
PRODUCT IS CERTIFIED BY THE
MANUFACTURER TO COMPLY
WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT
THE DATE OF MANUFACTURE.
MANUFACTURED:
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME
MINATO-KU, TOKYO 105-8001,
JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-RW/DVD-ROM SD-R2412
CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To
ensure proper use of this product, please read this
instruction manual carefully and retain for future
reference. Should the unit ever require maintenance,
contact an authorized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
PRODUCT IS CERTIFIED BY THE
MANUFACTURER TO COMPLY
WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT
THE DATE OF MANUFACTURE.
MANUFACTURED:
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME
MINATO-KU, TOKYO 105-8001,
JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
HITACHI
DVD-ROM GDR-8082N
CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
PRODUCT IS CERTIFIED BY THE
MANUFACTURER TO COMPLY
WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT
THE DATE OF MANUFACTURE.
MANUFACTURED:
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME
MINATO-KU, TOKYO 105-8001,
JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD±RW GWA-4040N
CAUTIONS: 1. The DVD±RW drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
THIS PRODUCT COMPLIES WITH
DHHS RULES 21 CFR SUBCHAPTER
J APPLICABLE AT DATE OF MANU-
FACTURE.
MANUFACTURED:
Hitachi-LG Data Storage, Inc.
26-5, TORANOMON 1-CHOME,
MINATO-KU, TOKYO, 105-0001
JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Pioneer
DVD±RW DVR-K12D
CAUTIONS: 1. The DVD±RW drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
MFD.
SER.NO.
CERTIFICATION
THIS PRODUCT COMPLIES WITH 21
CFR 1040. 10 AND 1040. 11 EXCEPT
FORDEVIATIONSPURSUANTTO
LASER NOTICE NO.50.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
PIONEERCORPORATION.
4-1, MEGURO 1-CHOME, MEGURO-
KU, TOKYO, 153-8854, JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Panasonic
DVD Multi UJ-811B
CAUTIONS: 1. The DVD Multi drive employs a laser system. To ensure
proper use of this product, please read this instruction
manual carefully and retain for future reference. Should
the unit ever require maintenance, contact an autho-
rized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.
Location of the required label
SERIALNO.
MANUFACTURED:
COMPLIESWITHFDARADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
Panasonic Communications Co., Ltd.
1-62, 4-Chome Minoshima, Hakata-Ku
Fukuoka,Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
CD-RW/DVD-ROM UJDA750
CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To
ensure proper use of this product, please read this
instruction manual carefully and retain for future
reference. Should the unit ever require maintenance,
contact an authorized service location.
2. Use of controls, adjustments or the performance of
procedures other than those specified may result in
hazardous radiation exposure.
3. To prevent direct exposure to the laser beam, do not try
to open the enclosure.CD-RW/DVD-ROM UJDA750
Location of the required label
COMPLIESWITHFDARADIATION
PERFORMANCE STANDARDS, 21 CFR
SUBCHAPTER J.
MANUFACTURED:
Panasonic Communications Co., Ltd.
1-62, 4-Chome Minoshima, Hakata-Ku
Fukuoka,Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
International precautions
CAUTION: This appliance contains a laser
system and is classified as a “CLASS 1
LASER PRODUCT.” To use this model
properly, read the instruction manual
carefully and keep this manual for your
future reference. In case of any trouble with
this model, please contact your nearest
“AUTHORIZED service station.” To prevent
direct exposure to the laser beam, do not try
to open the enclosure.
VORSICHT: Dieses Gerät enthält ein
Laser-System und ist als
CLASS 1 LASER PRODUCT
LASERSCHUTZKLASSE 1
PRODUKT
“LASERSCHUTZKLASSE1PRODUKT”
klassifiziert. Für den richtigen Gebrauch
dieses Modells lesen Sie bitte die
Bedienungsanleitung sorgfältig durch und
bewahren diese bitte als Referenz auf. Falls
Probleme mit diesem Modell auftreten,
benachrichtigen Sie bitte die nächste
“autorisierte Service-Vertretung”. Um
einen direkten Kontakt mit dem Laserstrahl
zu vermeiden darf das Gerät nicht geöffnet
werden.
TOEN60825
ADVARSEL: Denne mærking er anbragt
udvendigt på apparatet og indikerer, at
apparatet arbejder med laserstråler af klasse
1, hviket betyder, at der anvendes laserstrlier
af svageste klasse, og at man ikke på
apparatets yderside kan bilve udsat for
utilladellg kraftig stråling.
ADVERSEL: USYNLIG
LASERSTRÅLING VED ÅBNING,
NÅR SIKKERHEDSAF-BRYDER
ER UDE AF FUNKTION.
UNDGÅ UDSÆTTELSE FOR
STRÅLING
APPARATET BOR KUN ÅBNES AF
FAGFOLKMEDSÆRLIGTKENDSKABTIL
APPARATERMEDLASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer
imod at foretage sådanne indgreb i
apparatet, at man kan komme til at udsætte
sig for laserstråling.
Download from Www.Somanuals.com. All Manuals Search And Download.
OBS! Apparaten innehåller laserkomponent
som avger laserstråining överstigande
gränsen för laserklass 1.
VAROITUS. Suojakoteloa si saa avata. Laite
sisältää laserdiodin, joka lähetää
näkymätöntä silmilie vaarallista
lasersäteilyä.
CAUTION:USEOFCONTROLSOR
ADJUSTMENTSORPERFORMANCEOF
PROCEDURESOTHERTHANTHOSE
SPECIFIEDINTHEOWNER’SMANUAL
MAYRESULTINHAZARDOUSRADIATION
EXPOSURE.
VORSICHT:DIEVERWENDUNGVON
ANDERENSTEURUNGENODER
EINSTELLUNGENODERDAS
DURCHFÜHRENVONANDEREN
VORGÄNGENALSINDER
BEDIENUNGSANLEITUNGBESCHRIEBEN
KÖNNENGEFÄHRLICHE
STRAHLENEXPOSITIONENZURFOLGE
HABEN.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Preface
Manual contents ........................................................................... xxxiii
Conventions .................................................................................. xxxiv
Abbreviations ................................................................................... xxxiv
Icons ............................................................................................... xxxiv
Keys ............................................................................................... xxxiv
Keyoperation ................................................................................... xxxv
Display ............................................................................................. xxxv
Messages ........................................................................................ xxxv
General Precautions
Stressinjury ................................................................................. xxxvii
Heatinjury ...................................................................................... xxxvii
Pressure or impact damage............................................................ xxxvii
PCcardoverheating ...................................................................... xxxviii
Mobilephone ................................................................................. xxxviii
CentralProcessingUnit("CPU")PerformanceDisclaimer.............. xxxviii
The cautions on use of a Satellite A40 series computer.................. xxxix
Openthekeyboard brace ..................................................................... xl
Chapter 1 Introduction
Equipmentchecklist .......................................................................... 1-1
Hardware ............................................................................................ 1-1
Software ............................................................................................. 1-1
WindowsXPHomeEdition/Professional ............................................. 1-1
Features ............................................................................................. 1-2
Processor........................................................................................... 1-2
Memory .............................................................................................. 1-3
Power ................................................................................................. 1-3
Disks.................................................................................................. 1-4
Display ............................................................................................... 1-6
Keyboard ............................................................................................ 1-6
Pointingdevice ................................................................................... 1-7
Ports .................................................................................................. 1-7
xxv
Download from Www.Somanuals.com. All Manuals Search And Download.
Slots .................................................................................................. 1-7
Multimedia.......................................................................................... 1-7
Communications................................................................................. 1-8
Security.............................................................................................. 1-9
Software ............................................................................................. 1-9
Special features................................................................................. 1-9
Utilities.............................................................................................. 1-11
Options ............................................................................................. 1-13
Chapter 2 The Grand Tour
Front with the display closed ........................................................... 2-1
Left side.............................................................................................. 2-2
Right side ........................................................................................... 2-3
Back side ............................................................................................ 2-5
Underside ........................................................................................... 2-7
Front with the display open .............................................................. 2-8
Systemindicators .............................................................................. 2-9
Keyboardindicators ........................................................................ 2-10
USB diskette drive ........................................................................... 2-11
Fixed optical media drive .............................................................. 2-12
Region codes for DVD drives and media ........................................... 2-12
Writable discs .................................................................................. 2-13
CDs ............................................................................................... 2-13
DVDs ............................................................................................. 2-13
Formats............................................................................................ 2-13
DVD-ROMdrive ................................................................................ 2-14
CD-RW/DVD-ROMdrive ................................................................... 2-14
DVD-R/-RWdrive .............................................................................. 2-14
DVDMultidrive................................................................................. 2-15
DVD±RWdrive(DVDDualdrive) ....................................................... 2-15
AC adaptor ....................................................................................... 2-16
Chapter 3 Getting Started
Setting up your work space .............................................................. 3-1
Generalconditions.............................................................................. 3-2
Placement of the computer................................................................. 3-2
Seatingandposture ........................................................................... 3-3
Lighting .............................................................................................. 3-4
Work habits ........................................................................................ 3-4
xxvi
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC adaptor .............................................................. 3-5
Opening the display .......................................................................... 3-6
Turning on the power ....................................................................... 3-7
Starting up for the first time.............................................................. 3-8
Turning off the power ....................................................................... 3-8
Shut Down mode (Boot mode) ............................................................ 3-8
Standbymode .................................................................................. 3-11
Restarting the computer ................................................................. 3-13
Restoring the preinstalled software from
the Product Recovery DVD-ROM .................................................... 3-14
Chapter 4 Operating Basics
Using the Touch Pad ......................................................................... 4-1
Using the USB diskette drive ............................................................ 4-2
Connecting 3 1/2" diskette drive ......................................................... 4-2
Disconnecting 3 1/2" diskette drive ..................................................... 4-3
Using optical media drives ............................................................... 4-3
Loading discs ..................................................................................... 4-4
Removingdiscs .................................................................................. 4-6
Audio/Videocontrols ......................................................................... 4-7
Next and Previous buttons .................................................................. 4-7
Play/Pause and Stop buttons ............................................................. 4-8
Controls for CD/DVD and Digital Audio ............................................... 4-8
Writing CDs on CD-RW/DVD-ROM drive ........................................... 4-8
Beforewritingorrewriting.................................................................... 4-9
Writing CD/DVDs on DVD±RW drive (DVD Dual drive) .................. 4-10
Importantmessage ........................................................................... 4-10
Disclaimer ........................................................................................ 4-10
Writing CD/DVDs on DVD-R/-RW drive ........................................... 4-11
Importantmessage ........................................................................... 4-11
Disclaimer ........................................................................................ 4-11
Writing CD/DVDs on DVD Multi drive ............................................. 4-12
Importantmessage ........................................................................... 4-12
Disclaimer ........................................................................................ 4-12
Beforewritingorrewriting.................................................................. 4-12
Drag’nDropCD+DVD ....................................................................... 4-15
Dataverification ................................................................................ 4-16
Media care ....................................................................................... 4-16
xxvii
Download from Www.Somanuals.com. All Manuals Search And Download.
CD/DVDs.......................................................................................... 4-16
Diskettes .......................................................................................... 4-17
Sound System .................................................................................. 4-17
Volumecontrol ................................................................................. 4-17
Microphonelevel ............................................................................... 4-17
SoundMAXControlPanel ................................................................. 4-18
MicrophoneEnhancements .............................................................. 4-18
Powermanagement .......................................................................... 4-18
Modem.............................................................................................. 4-19
Regionselection ............................................................................... 4-19
Propertiesmenu ............................................................................... 4-20
Connecting ....................................................................................... 4-21
Disconnecting................................................................................... 4-22
WirelessLAN.................................................................................... 4-22
Security............................................................................................ 4-23
Wireless communication switch ....................................................... 4-23
WirelesscommunicationIndicator .................................................... 4-24
LAN ................................................................................................... 4-24
LAN cable types ............................................................................... 4-24
ConnectingLANcable ...................................................................... 4-25
Disconnecting LAN cable ................................................................. 4-26
Cleaning the computer ................................................................... 4-26
Moving the computer ...................................................................... 4-26
Heat dispersal .................................................................................. 4-27
Chapter 5 The Keyboard
Typewriter keys................................................................................... 5-1
F1 … F12 function keys ...................................................................... 5-2
Soft keys: Fn key combinations......................................................... 5-2
Emulating keys on enhanced keyboard............................................. 5-2
Hot keys ........................................................................................... 5-4
Fn Sticky key ................................................................................... 5-6
Windows special keys ........................................................................ 5-7
Keypad overlay................................................................................... 5-7
Turning on the overlays ..................................................................... 5-7
Temporarily using normal keyboard
(overlay on) ....................................................................................... 5-8
Temporarily using overlay (overlay off)................................................ 5-9
Temporarily changing modes............................................................. 5-9
Generating ASCII characters ............................................................. 5-9
xxviii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Power and Power-Up Modes
Power conditions................................................................................ 6-1
Power indicators ................................................................................ 6-2
Battery indicators.............................................................................. 6-2
DC IN 15V indicator .......................................................................... 6-3
Power indicator ................................................................................. 6-3
Battery types ....................................................................................... 6-3
Battery pack ..................................................................................... 6-4
Real Time Clock battery.................................................................... 6-4
Care and use of the battery pack ...................................................... 6-5
Safety precautions ............................................................................ 6-5
Charging the batteries ....................................................................... 6-8
Monitoring battery capacity ............................................................. 6-10
Maximizing battery operating time .................................................. 6-10
Retaining data with power off........................................................... 6-11
Extending battery life ...................................................................... 6-11
Replacing the battery pack.............................................................. 6-12
Removing the battery pack.............................................................. 6-12
Installing the battery pack ............................................................... 6-14
Starting the computer by password ................................................ 6-15
Power-up modes .............................................................................. 6-15
Windows utilities............................................................................. 6-15
Hot keys ......................................................................................... 6-15
Panel power off ................................................................................ 6-16
System Auto Off ................................................................................ 6-16
Chapter 7 HW Setup and Passwords
HW Setup ........................................................................................... 7-1
Accessing HW Setup ......................................................................... 7-1
HW Setup window .............................................................................. 7-1
Supervisorpassword ....................................................................... 7-10
Chapter 8 Optional Devices
PCcards ............................................................................................. 8-2
Inserting a PC card ............................................................................. 8-2
RemovingaPCcard ........................................................................... 8-3
SDcards ............................................................................................. 8-4
Formatting an SD card ....................................................................... 8-4
Inserting an SD card ........................................................................... 8-4
xxix
Download from Www.Somanuals.com. All Manuals Search And Download.
RemovinganSDcard ......................................................................... 8-5
SD card care ...................................................................................... 8-6
Memory expansion ............................................................................ 8-6
Installingmemorymodule ................................................................... 8-7
Removingmemorymodule................................................................ 8-10
Battery pack ..................................................................................... 8-11
AC adaptor ....................................................................................... 8-11
USB diskette drive ........................................................................... 8-12
External monitor .............................................................................. 8-12
i.LINK(IEEE1394) .............................................................................. 8-13
Precautions ...................................................................................... 8-13
Connecting ....................................................................................... 8-14
Disconnecting................................................................................... 8-15
Security lock .................................................................................... 8-15
Chapter 9 Troubleshooting
Problemsolvingprocess................................................................... 9-1
Preliminary checklist .......................................................................... 9-1
Analyzing the problem ........................................................................ 9-2
Hardware and system checklist........................................................ 9-3
System start-up.................................................................................. 9-3
Self test.............................................................................................. 9-4
Power ................................................................................................. 9-4
Battery ............................................................................................... 9-6
Password ........................................................................................... 9-7
Keyboard ............................................................................................ 9-7
LCDpanel ........................................................................................ 9-10
Harddiskdrive .................................................................................. 9-11
DVD-ROMdrive ................................................................................ 9-12
CD-RW/DVD-ROMdrive ................................................................... 9-13
DVD-R/-RWdrive .............................................................................. 9-14
DVDMultidrive................................................................................. 9-16
DVD±RWdrive(DVDDualdrive) ....................................................... 9-18
Diskettedrive.................................................................................... 9-19
PC card ............................................................................................ 9-20
SD card ............................................................................................ 9-20
Pointingdevice ................................................................................. 9-21
USB ................................................................................................. 9-23
Memoryexpansion ........................................................................... 9-24
Sound System ................................................................................. 9-24
Monitor ............................................................................................. 9-25
xxx
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem ............................................................................................. 9-25
Standby/Hibernation ......................................................................... 9-27
LAN .................................................................................................. 9-27
Wireless LAN ................................................................................... 9-27
i.LINK(IEEE1394) ............................................................................ 9-28
Real Time Clock ............................................................................... 9-28
Printer .............................................................................................. 9-29
TOSHIBAsupport ............................................................................. 9-30
Before you call ................................................................................. 9-30
Where to write .................................................................................. 9-30
Appendixes
Appendix A
Specifications ................................................................................... A-1
Appendix B
Display Controller and Modes ......................................................... B-1
Appendix C
ATCommands .................................................................................. C-1
Appendix D
S-registers ......................................................................................... D-1
Appendix E
V.90 .....................................................................................................E-1
Appendix F
Internal Modem Guide ...................................................................... F-1
Appendix G
WirelessLAN..................................................................................... G-1
Appendix H
AC Power Cord and Connectors...................................................... H-1
Appendix I
PartsNumbers .................................................................................... I-1
Glossary
Index
xxxi
Download from Www.Somanuals.com. All Manuals Search And Download.
xxxii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Congratulations on your purchase of the TOSHIBA Satellite A40 computer. This
powerful, notebook computer is designed to provide years of reliable, high-
performancecomputing.
This manual tells how to set up and begin using your TOSHIBA Satellite A40
computer. It also provides detailed information on configuring your computer, basic
operations and care, using optional devices and troubleshooting.
If you are a new user of computers or if you’re new to portable computing, first read
over the Introduction and The Grand Tour chapters to familiarize yourself with the
computer’s features, components and accessory devices. Then read Getting
Started for step-by-step instructions on setting up your computer.
If you are an experienced computer user, please continue reading the preface to
learn how this manual is organized, and then become acquainted with this manual
by browsing through its pages. Be sure to look over the Special features section of
the Introduction, to learn about features that are uncommon or unique to the
computers and carefully read HW Setup and Passwords. If you are going to install
PC cards or connect external devices such as a monitor, be sure to read Chapter 8,
Optional Devices.
Manual contents
This manual is composed of nine chapters, nine appendixes, a glossary, and an
index.
Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and
options.
Chapter 2, The Grand Tour, identifies the components of the computer and briefly
explains how they function.
Chapter 3, Getting Started, provides a quick overview of how to begin operating
your computer and gives tips on safety and designing your work area.
Chapter 4, Operating Basics, includes tips on care of the computer and on using the
Touch Pad, the optical media drive, external diskette drive, Wireless LAN, LAN and
internalmodem.
Chapter 5, The Keyboard, describes special keyboard functions including the
keypad overlay and hotkeys.
xxxiii
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Chapter 6, Power and Power-Up Modes, gives details on the computer’s power
resources and battery save modes.
Chapter 7, HW Setup and Passwords, explains how to configure the computer using
the HW Setup program. It also tells how to set a password.
Chapter 8, Optional Devices, describes the optional hardware available.
Chapter 9, Troubleshooting, provides helpful information on how to perform some
diagnostic tests, and suggests courses of action if the computer doesn’t seem to be
working properly.
The Appendixes provide technical information about your computer.
The Glossary defines general computer terminology and includes a list of acronyms
used in the text.
The Index quickly directs you to the information contained in this manual.
Conventions
This manual uses the following formats to describe, identify, and highlight terms
and operating procedures.
Abbreviations
On first appearance, and whenever necessary for clarity, abbreviations are enclosed
in parentheses following their definition. For example: Read Only Memory
(ROM). Acronyms are also defined in the Glossary.
Icons
Icons identify ports, dials, and other parts of your computer. The indicator panel
also uses icons to identify the components it is providing information on.
Keys
The keyboard keys are used in the text to describe many computer operations. A
distinctive typeface identifies the key top symbols as they appear on the keyboard.
For example, Enter identifies the Enter key.
xxxiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
Key operation
Some operations require you to simultaneously use two or more keys. We identify
such operations by the key top symbols separated by a plus sign (+). For example,
Ctrl + C means you must hold down Ctrl and at the same time press C. If three
keys are used, hold down the first two and at the same time press the third.
ABC When procedures require an action such as clicking an icon or entering
text, the icon’s name or the text you are to type in is represented in the
type face you see to the left.
Display
ABC
Names of Windows® or icons or text generated by the computer that
appears on its display screen is presented in the type face you see to the
left.
Messages
Messages are used in this manual to bring important information to your attention.
Each type of message is identified as shown below.
CAUTION: Pay attention! A caution informs you that improper use of
equipment or failure to follow instructions may cause data loss or
damage your equipment.
NOTE: Please read. A note is a hint or advice that helps you make best
use of your equipment.
xxxv
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
xxxvi
Download from Www.Somanuals.com. All Manuals Search And Download.
General Precautions
TOSHIBA computers are designed to optimize safety, minimize strain and withstand
the rigors of portability. However, certain precautions should be observed to further
reduce the risk of personal injury, damage to the computer or impaired performance.
Be certain to read the general precautions below and to note the cautions included
in the text of the manual.
Stress injury
Carefully read the Instruction Manual for Safety & Comfort. It contains information
on prevention of stress injuries to your hands and wrists than can be caused by
extensive keyboard use. Chapter 3, Getting Started, also includes information on
work space design, posture and lighting that can help reduce physical stress.
Heat injury
❑
Avoid prolonged physical contact with the computer. If the computer is used
for long periods, its surface can become very warm. While the temperature will
not feel hot to the touch, if you maintain physical contact with the computer for
a long time (if you rest the computer on your lap, or if you keep your hands on
the palm rest, for example) your skin might suffer low-heat injury.
❑
❑
If the computer has been used for a long time, avoid direct contact with the
metal plate supporting the I/O ports. It can become hot.
The surface of the AC adaptor can become hot when in use. This condition
does not indicate a malfunction. If you need to transport the AC adaptor,
disconnect it and let it cool before moving it.
❑
Do not lay the AC adaptor on a material that is sensitive to heat. The material
could be damaged.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to strong impact.
Excessive pressure or impact can cause damage to computer components or
otherwise cause malfunctions.
xxxvii
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
PC card overheating
Some PC cards can become hot with prolonged use. Overheating of a PC card can
result in errors or instability in the PC card operation. Also be careful when you
remove a PC card that has been used for a long time.
Mobile phone
Use of mobile phones can interfere with the audio system. Computer operation is
not impaired but it is recommended that a distance of 30 cm be maintained between
the computer and a mobile phone in use.
Central Processing Unit ("CPU") Performance
Disclaimer
CPU performance in your computer product may vary from specifications under the
followingconditions:
❑
❑
❑
❑
❑
Use of certain peripheral products
Use of battery power instead of AC power
Use of certain multimedia games or videos with special effects
Use of standard telephone lines or low speed network connections
Use of complex modeling software, such as high end computer aided design
applications
❑
❑
Use of the computer in areas with low air pressure (high altitude > 1,000 meters
or > 3,280 feet above sea level)
Use of the computer at temperatures outside the range of 5°C to 30°C (41°F to
86°F)or>25°C(77°F)athighaltitude(alltemperaturereferencesareapproxi-
mate).
Under some conditions, your computer product may automatically shut down. This
is a normal protective feature designed to reduce the risk of lost data or damage to
the product when used outside recommended conditions. To avoid risk of lost data,
always make back-up copies of data by periodically storing it on an external storage
medium. For optimum performance, use your computer product only under
recommended conditions. Read additional restrictions in bundled documents.
Contact TOSHIBA Service and Support for more information.
xxxviii
Download from Www.Somanuals.com. All Manuals Search And Download.
Stress injury
The cautions on use of a Satellite A40 series
computer.
1. Cleaning of the dust accumulated on the cooling vent of the computer.
CAUTION: When you use your computer in a dusty area, the dusts
accumulate on a cooling vent at the under side of your computer. The
accumulated dusts cause insufficient heat dissipation. Clean the dusts off
with vacuum cleaner.
2. Cooling vent at the underside of the computer.
COOLING VENT
CAUTION: To prevent possible overheating of the CPU, make sure the
cooling fan’s air intake is not blocked. The fan draws in air by creating
a vacuum. If the fan is blocked, it could cause the CPU to run at a lower
performance levelor cause the computer to shut down. Loose items such
as notebook and tissue paper, plastic wrappers, or other similar
materials can block the air intake, preventing air from reaching the
CPU. Do not use the computer on surfaces with objects that can be
drawn in by the cooling fan.
xxxix
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Open the keyboard brace
CAUTION: Memory module and the work of the replacement of the
internal modem etc. detach keyboard brace, bases such as speakers and
Power buttons become baring. Never touch substrates such as speakers
and Power buttons of baring. It causes the breakdown when touching.
SPEAKERS OF BARING
POWER OF BARING
Open the keyboard brace
xl
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Equipmentchecklist .......................................................................... 1-1
Hardware ............................................................................................ 1-1
Software ............................................................................................. 1-1
WindowsXPHomeEdition/Professional ............................................. 1-1
Features ............................................................................................. 1-2
Processor........................................................................................... 1-2
Memory .............................................................................................. 1-3
Power ................................................................................................. 1-3
Disks.................................................................................................. 1-4
Display ............................................................................................... 1-6
Keyboard ............................................................................................ 1-6
Pointingdevice ................................................................................... 1-7
Ports .................................................................................................. 1-7
Slots .................................................................................................. 1-7
Multimedia.......................................................................................... 1-7
Communications................................................................................. 1-8
Security.............................................................................................. 1-9
Software ............................................................................................. 1-9
Special features................................................................................. 1-9
Utilities.............................................................................................. 1-11
Options ............................................................................................. 1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
This chapter provides an equipment checklist, and it identifies the computer’s
features, options and accessories.
CAUTION: Some of the features described in this manual may not
function properly if you use an operating system that was not prein-
stalled by TOSHIBA.
Equipment checklist
Carefully unpack your computer. Save the box and packing materials for future use.
Hardware
Check to make sure you have all the following items:
❑
❑
❑
❑
SatelliteA40SeriesPortablePersonalComputer
Universal AC adaptor and power cord
USB diskette drive (Provided with some models)
Modular cable
Software
Windows XP Home Edition/Professional
❑
The following software is preinstalled:
• Microsoft® Windows XP Home Edition/Professional
• Modemdriver
• Display Drivers for Windows
• TOSHIBAUtilities
• Wireless LAN driver (Can be used only for Wireless LAN models)
• Sound Driver for Windows
• DVDVideoPlayer
• LANDrivers
• ALPSPointingdeviceDriver
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
• TOSHIBAPowerSaver
• TOSHIBAConsole
• Onlinemanual
• TOSHIBAConfigFree
• TOSHIBA Touch and Launch
• TOSHIBAPCDiagroticTool
❑
❑
Documentation:
• Satellite A40 User's Manual
• Microsoft Windows XP manual package
• Instruction Manual for Safety & Comfort
• End User License Agreement
ProductRecoveryDVD-ROM
Features
The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple-
mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide
compactsize, minimumweight, lowpowerusage, andhighreliability. Thiscomputer
incorporates the following features and benefits:
Processor
Built-in The computer is equipped with an Intel® processor.
Intel® Celeron® processor,
whichincorporatesa128KBlevel2cachememory.
2.40GHzIntel®Celeron® processor2.40GHz
2.50GHzIntel®Celeron® processor2.50GHz
2.60GHzIntel®Celeron® processor2.60GHz
2.70GHzIntel®Celeron® processor2.70GHz
2.80GHzIntel®Celeron® processor2.80GHz
Mobile Intel® Pentium® 4-M processor
whichincorporatesa512KBlevel2cachememory.
2.66GHzMobileIntel® Pentium® 4processor2.66GHz-M
2.80GHzMobileIntel® Pentium® 4processor2.80GHz-M
3.06GHzMobileIntel® Pentium® 4processor3.06GHz-M
3.20GHzMobileIntel® Pentium® 4processor3.20GHz-M
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2
Features
Mobile Intel® Pentium® 4 processor
whichincorporatesa512KBlevel2cachememory.
Mobile Intel® Pentium® 4 processor 2.66GHz supporting
Hyperthreading Technology(*1)
Mobile Intel® Pentium® 4 processor 2.88GHz supporting
Hyperthreading Technology(*1)
Mobile Intel® Pentium® 4 processor 3.06GHz supporting
Hyperthreading Technology(*1)
Mobile Intel® Pentium® 4 processor 3.20GHz supporting
Hyperthreading Technology(*1)
(*1)Hyper-Threading Technology requires a computer
system with an Intel® Pentium® 4 processor supporting HT
Technology and a Hyper-Threading Technology enabled
chipset, BIOS and operating system.
Performance will vary depending on the specific hardware
and software you use.
Seehttp://www.intel.com/info/hyperthreading/formore
information including details on which processors support
HT Technology.
Memory
Slots 256, 512or1GBmemorymodulescanbeinstalledinthe
twomemoryslotsforamaximumof2GBsystemmemory.
VideoRAM Part of system memory is used for Video RAM, of which
available capacity depends on the size of system memory:
•
256MBormoreofsystemmemory:themaximum
VideoRAMcapacityis64MB.
Power
Battery pack The computer is powered by one rechargeable lithium-ion
battery pack.
RTCbattery The computer has an internal battery to back up the
internalRealTimeClock(RTC)andcalendar.
AC adaptor The Universal AC adaptor provides power to the system
and recharges the batteries when they are low. It comes
with a detachable power cord.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Because it is universal, it can receive a range of AC voltage
from 100 to 240 volts; however, the output current varies
among different models. Using the wrong model can
damage your computer. See the AC adaptor section in
Chapter 2, The Grand Tour.
Disks
Harddiskdrive Available in four sizes.
• 7.94GB(30.0billionbytes)
• 37.26GB(40.0billionbytes)
• 55.88GB(60.0billionbytes)
• 74.53GB(80.0billionbytes)
USB diskette drive Accommodateseither31/2"1.44-megabyteor720-kilobyte
diskettes. It connects to a USB port.
(Provided with some models)
DVD-ROMdrive Somemodelsareequippedwithafull-size,DVD-ROM
drive module that lets you run either 12 cm (4.72") or 8 cm
(3.15")CDsor12cm(4.72")DVDswithoutusingan
adaptor. It runs DVD-ROMs at maximum 8 speed and CD-
ROMs at maximum 24 speed. The drive supports the
followingformats:
• DVD-ROM
• CD-DA
• DVD-Video
• CD-Text
• PhotoCD™(single/multi-session)
• CD-ROMMode1, Mode2
• CD-ROMXAMode2(Form1,Form2)
• EnhancedCD(CD-EXTRA)
• CD-G(AudioCDonly)
• Addressing Method 2
CD-RW/DVD-ROM Somemodelsareequippedwithafull-size,CD-RW/DVD-
drive ROM drive module that lets you run CD/DVDs without
using an adaptor. It reads DVD-ROMs at maximum 8 speed
andCD-ROMsatmaximum24speed. ItwritesCD-Ratup
to 24 speed and CD-RW at up to 10 speed. For reading,
this drive supports the same formats as the DVD-ROM
drive.
• DVD-ROM
• CD-DA
• DVD-Video
• CD-Text
• PhotoCD™(single/multi-session)
• CD-ROMMode1, Mode2
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
• CD-ROMXAMode2(Form1,Form2)
• EnhancedCD(CD-EXTRA)
• CD-G(AudioCDonly)
• Addressing Method 2
DVD-R/-RWdrive Somemodelsareequippedwithafull-sizeDVD-R/-RW
drive module that lets you record data to rewritable CD/
DVDsaswellasruneither12cm(4.72")or8cm(3.15")
CDs/12cm(4.72") DVDs without using an adaptor. It reads
DVD-ROMsatmaximum8speedandCD-ROMsat
maximum24speed. ItwritesCD-Ratupto16speed, CD-
RW at up to 10 speed, DVD-R and DVD-RW at single
speed. This drive supports the same formats as the DVD-
ROMdrive.
• DVD-ROM
• CD-DA
• DVD-Video
• CD-Text
• PhotoCD™(single/multi-session)
• CD-ROMMode1, Mode2
• CD-ROMXAMode2(Form1,Form2)
• EnhancedCD(CD-EXTRA)
• CD-G(AudioCDonly)
• Addressing Method 2
DVD Multi drive Somemodelsareequippedwithafull-sizeDVDMultidrive
module that lets you record data to rewritable CD/DVDs as
wellasruneither12cm(4.72")or8cm(3.15")CD/DVDs
without using an adaptor. An ATAPI interface controller
is used for CD/DVD-ROM operation. The drive reads
DVDsatmaximum8speedandCDsatmaximum24speed.
Itwrites DVD-RWatmaximumsinglespeed,DVD-Rand
DVD-RAMatmaximum2speed,CD-Ratmaximum16
speed, and CD-RW at maximum 8 speed (High-speed
media). The drive supports the following formats:
• DVD-ROM
• DVD-R
• DVD-Video
• DVD-RW
• CD-ROM
• PhotoCD™
• CD-ROMXA
• CD-I
• DVD-RAM
• CD-EXTRA
•
Audio CD
• CD-DA
• CD-Text
• CD-RW
• CD-R
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
DVD±RWdrive Somemodelsareequippedwithafull-sizeDVD±RWdrive
(DVDDualdrive) module that lets you record data to rewritable CD/DVDs as
wellasruneither12cm(4.72")or8cm(3.15")CD/DVDs
without using an adaptor. It reads DVD-ROMs at maximum
8speedandCD-ROMsatmaximum24speed. ItwritesCD-
R at up to 16 speed, CD-RW at up to 10 speed, DVD-R and
DVD-RWatmaximum2speed.DVD+RandDVD+RWat
maximum 2.4 speed. This drive supports the same formats
astheDVD-ROMdrive.
• DVD-ROM
• DVD-R
• DVD+R
• DVD-Video
• DVD-RW
• DVD+RW
• CD-DA• CD-Text
• PhotoCD(single/multi-session)
• CD-ROMMode1,Mode2
• CD-ROMXAMode2(Form1,Form2)
• EnhancedCD(CD-EXTRA)
• CD-G(Audio CD only)•Addressing Method 2
Display
The computer’s LCD panel supports high-resolution video graphics. The screen
can be set at a wide range of viewing angles for maximum comfort and readability.
Built-in 14.1"XGATFTscreenor15.0"XGA/SXGA+TFTscreen,
16 M colors, with one of the following resolutions:
•
XGA,1024horizontal×768verticalpixels
• SXGA+,1400horizontal×1050verticalpixels
Graphicscontroller Graphicscontrollermaximizesdisplayperformance.Refer
to Appendix B for more information.
Keyboard
Built-in 85 keys or 86 keys, compatible with IBM enhanced
keyboard, embedded numeric overlay, dedicated cursor
control,
and
for details.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Pointing device
Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable
control of the on-screen pointer.
Ports
Parallel Some models are equipped with a parallel port for parallel
printer or other parallel device (ECP compatible).Note that
some models are not equipped with this port.
Externalmonitor 15-pin,analogVGAportsupportsVESADDC2Bcompat-
ible functions.
UniversalSerialBus The computer has four Universal Serial Bus ports that
(USB2.0) comply with the USB 2.0 standard, which enables data
transfer speeds 40 times faster than the USB 1.1 standard.
(The ports also support USB 1.1.)
i.LINK™(IEEE1394) This port enables high-speed data transfer directly from
external devices such as digital video cameras. Some
models are equipped with a i.LINK port.
Slots
PCcard The PC card slot accommodates one 5 mm Type II card.
SDcard This slot lets you easily transfer data from devices, such as
digital cameras and Personal Digital Assistants that use
SD card flash-memory.You can use memory module in this
slot. Some models are equipped with a SD card slot.
Multimedia
Sound System Windows Sound System compatible Sound System
provides internal speakers as well as jacks for an external
microphone and headphone.
Headphone jack This jack outputs analog audio signals.
Microphone jack A 3.5 mm mini microphone jack enables connection of a
three-conductor mini jack for monaural microphone input.
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Communications
Modem An internal modem provides capability for data and fax
communication. It supports V.90 (V.92). Refer toAppendix
E. The speed of data transfer and fax depends on analog
telephone line conditions. It has a modem jack for connect-
ing to a telephone line. It is preinstalled as a standard
device in some markets. Both of V.90 and V.92 are sup-
ported only in USA and Canada and Australia. Only V.90 is
available in other regions.
LAN The computer is equipped with a LAN card that supports
EthernetLAN(10Mbit/s, 10BASE-T)andFastEthernet
LAN(100Mbit/s,100BASE-TX).Itispreinstalledasa
standard device in some markets.
WirelessLAN Some computers in this series are equipped with a wireless
LANmini-PCIcardthatiscompatiblewithotherLANsystems
based on Direct Sequence Spread Spectrum / Orthogonal
Frequency Division Multiplexing radio technology that
complieswiththe IEEE802.11Standard(RevisionA,BorG),
and Turbo Mode.
❑
Automatic Transmit Rate Select mechanism in the transmit
range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s. (Revision A
andG, RevisionB/G, A/B/Gcombotype)
❑
❑
Automatic Transmit Rate Select mechanism in the transmit
range of 11, 5.5, 2 and 1 Mbit/s. (Revision B)
Automatic Transmit Rate Select mechanism in the transmit
rangeof108, 96, 72, 48, 36, 24, 18and12Mbit/s. (Turbo
Mode, Revision A/B/G combo type)
❑
FrequencyChannelSelection(5GHz:RevisionA/2.4GHz:
RevisionB/G)
❑
❑
❑
Roamingovermultiplechannels
CardPowerManagement
Wired Equivalent Privacy (WEP) data encryption, based on
152bitencryptionalgorithm.(RevisionB/G,A/B/Gcombo
type). Wired Equivalent Privacy (WEP) data encryption, based
on128bitencryptionalgorithm. (RevisionBonlytype).
❑
Advanced Encryption Standard (AES) data encryption, based
on256bitencryptionalgorithm.(RevisionB/G,A/B/Gcombo
type)
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Special features
Security
Security lock slot Connects an optional security lock to anchor the computer
to a desk or other large object.
Software
Operating System Windows XP Home Edition/Professional Edition operating
system and TOSHIBA Utilities and drivers preinstalled on
the hard disk. Refer to the Software section at the front of
this chapter.
TOSHIBAUtilities A number of utilities and drivers are preinstalled to make
your computer more convenient to use. Refer to the
Utilities section in this chapter.
Plug and Play When you connect an external device to the computer or
when you install a component, Plug and Play capability
enables the system to recognize the connection and make
the necessary configurations automatically.
Special features
The following features are either unique to TOSHIBA computers or are advanced
features, which make the computer more convenient to use.
Hot keys Key combinations let you quickly modify the system
configuration directly from the keyboard without running a
system configuration program.
Displayautomatic This feature automatically cuts off power to the internal
poweroff display when there is no keyboard input for a time
specified. Power is restored when any key is pressed. You
can specify the time in the Monitor Power off item of the
Basic Setup tab in TOSHIBA Power Saver.
HDDautomatic This feature automatically cuts off power to the hard disk
poweroff drive when it is not accessed for a time specified. Power is
restored when the hard disk is accessed. You can specify
the time in the HDD Power off item of the Basic Setup tab
windowinTOSHIBAPowerSaver.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Systemautomatic This feature automatically shuts down the system in
Standby/Hibernation standby mode or Hibernation mode when there is no input
or hardware access for a time specified. You can specify
the time and select either System Standby or System
Hibernate in the System standby and System hibernation
item of the Basic Setup tab in TOSHIBA Power Saver.
Keypad overlay A ten-key pad is integrated into the keyboard. Refer to the
Keypad overlay section in Chapter 5, The Keyboard, for
instructions on using the keypad overlay.
Power on password Two levels of password security are available: supervisor
and user. This feature prevents unauthorized access to
your computer.
Instant security A hot key function blanks the screen and disables the
computer providing quick and easy data security.
Intelligent A microprocessor in the computer’s intelligent power
power supply supply detects the battery’s charge and calculates the
remaining battery capacity. It also protects electronic
components from abnormal conditions, such as voltage
overload from a universal AC adaptor. You can monitor
remaining battery capacity. Use the Battery remaining item
of the Power Save Modes window in TOSHIBA Power
Saver.
Battery save mode This feature lets you save battery power. You can specify
the Power Save Mode in the Profile item in TOSHIBA
PowerSaver.
Panel power on/off This feature turns power to the computer off when the
display panel is closed and turns it back on when the panel
is opened. You can specify the setting in the When I close
the lid item of the Setup Action tab in TOSHIBA Power
Saver.
Low battery When battery power is exhausted to the point that
automatic hibernation computer operation cannot be continued, the system
automatically enters Hibernation and shuts down. You can
specify the setting in Setup Action tab in TOSHIBA Power
Saver.
Heat dispersal To protect from overheating, the CPU has an internal
temperature sensor. If the computer’s internal temperature
rises to a certain level, the cooling fan is turned on or the
processing speed is lowered. Use the Fan item of the Basic
Setup tab in TOSHIBA Power Saver.
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities
Maximum
Turns on fan first, then if necessary
Performance
lowers CPU processing speed.
Performance
Uses a combination of fan and
lowering the CPU processing speed.
Batteryoptimized Lowers the CPU processing speed
first, then if necessary turns on the
fan.
Hibernation This feature lets you turn off the power without exiting
from your software. The contents of main memory are
saved to the hard disk, when you turn on the power again,
you can continue working right where you left off. Refer to
the Turning off the power section in Chapter 3, Getting
Started, for details.
Standby If you have to interrupt your work, you can turn off the
power without exiting from your software. Data is main-
tained in the computer’s main memory. When you turn on
the power again, you can continue working right where
you left off.
Utilities
This section describes preinstalled utilities and tells how to start them. For details
on operations, refer to each utility’s online manual, help files or readme.txt files.
TOSHIBAPowerSaver To access this power savings management program, click
the Control Panel and select the TOSHIBA Power Saver
icon.
HW Setup This program lets you customize your hardware settings
according to the way you work with your computer and
the peripherals you use. To start the utility, click the
Windows Start button and click Control Panel. Click the
Printers and other Hardware, select the TOSHIBA HW
Setup icon.
Fn-esse This Windows program lets you define your own “short-
cut” keys to quickly launch applications and speed your
work in Windows. To start the utility, click the Windows
Start button, point to All Programs, point to TOSHIBA,
point to Utilities and click Fn-esse.
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
DVDVideoPlayer The DVD Video Player is used to play DVD-Video. It has
an on-screen interface and functions. Click Start, point to
AllPrograms, pointtoInterVideoWinDVD4, thenclick
InterVideoWinDVD4.
ConfigFree ConfigFree is a suite of utilities to allow easy control of
communication device and network connections.
ConfigFree also allows you to find communication
problems and create profiles for easy switching between
location and communication networks.
To start ConfigFree, click the Windows Start Button, point
to All Progrums, point to TOSHIBA, point to Networking
andclickConfigFree.
Drag’nDrop This easy-to-use software lets you record CD/DVDs with
CD+DVD just a few mouse clicks. You can create CD/DVDs in
several formats including audio CDs that can be played on
a standard stereo CD player and data CDs to store the files
and folders on your hard drive. This software can be used
onamodelwithCD-RW/DVD-ROMdrive,DVDMulti
drive,DVD-R/-RWdriveandDVD±RWdrive.
TOSHIBA Touch Pad Pressing Fn + F9 in a windows environment enables or
On/OffUtility disables the Touch Pad function. When you press these
hot keys, the current setting will change and be displayed
as an icon.
TOSHIBA Touch and TOSHIBA Touch and Launch is a tool that allows you to
Launch perform various tasks easily using Touch pad. TOSHIBA
Touch and Launch is useful in the following conditions.
- To open a file located on the desktop whose icon is
obscured by a window.
- To open a page contained in the Internet Explorer
Favorites menu.
- To display the list of currently open windows and
change the active window.
Also TOSHIBA Touch and Launch provides the following
functions by customizing the settings.
- To open a file stored in a predefined folder.
- To quickly launch your frequently used applications
which have been registered.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
PC Diagnostic TOSHIBA PC Diagnostic Tool displays the basic in-
Tool formation on PC, and the test of built-in devices can also
be performed.You can boot TOSHIBA PC Diagnostic Tool
form the menu bar as follows.
[Start]-[AllPrograms]-[TOSHIBA]-[Utilities]-[PCDiagnos-
ticTool]
Options
You can add a number of options to make your computer even more powerful
and convenient to use. The following options are available:
Memoryexpansion 256or512MBmemorymodule(PC2700,DDR)caneasily
be installed in the computer.
Batterypack(Black) An addition Battery pack can be purchased from your
TOSHIBA dealer. The Battery Pack is identical to the one
that came with your computer. Use it as a spare or replace-
ment.
Universal AC adaptor If you use your computer at more than one site frequently,
it may be convenient to purchase an additional universal
AC adaptor for each site so you will not have to carry the
adaptor with you.
USBFDDKit A 3 1/2" diskette drive accommodates 1.44-megabyte or
720-kilobyte diskette. It connects to a USB port. (You
cannot format 720-kilobyte diskettes on Windows XP, but
you can use previously formatted disks.)
Securitylock The slots is available to attach a security cable to the
computer to deter theft.
Bluetooth SD card2 Bluetooth SD card is an optional accessory compatible
with the SD Card slot of this computer. You can buy the
cardfromTOSHIBAdealer.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
The Grand Tour
Front with the display closed ........................................................... 2-1
Left side.............................................................................................. 2-2
Right side ........................................................................................... 2-3
Back side ............................................................................................ 2-5
Underside ........................................................................................... 2-7
Front with the display open .............................................................. 2-8
Systemindicators .............................................................................. 2-9
Keyboardindicators ........................................................................ 2-10
USB diskette drive ........................................................................... 2-11
Fixed optical media drive .............................................................. 2-12
Region codes for DVD drives and media ........................................... 2-12
Writable discs .................................................................................. 2-13
CDs.................................................................................................... 2-13
DVDs ................................................................................................. 2-13
Formats............................................................................................ 2-13
DVD-ROMdrive ................................................................................ 2-14
CD-RW/DVD-ROMdrive ................................................................... 2-14
DVD-R/-RWdrive .............................................................................. 2-14
DVDMultidrive................................................................................. 2-15
DVD±RWdrive(DVDDualdrive) ....................................................... 2-15
AC adaptor ....................................................................................... 2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
The Grand Tour
This chapter identifies the various components of your computer. Become familiar
with each component before you operate the computer.
Front with the display closed
Figure 2-1 shows the computer’s front with its display panel in the closed position.
DISPLAY LATCH
SYSTEM INDICATORS
Figure 2-1 Front of the computer with display closed
Display latch This latch secures the LCD panel in its closed position.
Slide the latch to open the display.
System LEDs let you monitor the status of various computer
indicators functions. Details are given in the Indicators section.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Left side
Figure 2-2 shows the computer’s left side.
LINK INDICATOR
LANACTIVE
(GREEN)
INDICATOR (ORANGE)
I.LINK(IEEE1394)PORT
SD CARD SLOT
USBPORTS
PC CARD SLOT
LANJACK
SD CARD INDICATOR
* Some models are not equipped with a SD card slot or a i.LINK (IEEE1394) port.
Figure 2-2 The left side of the computer
LAN active This indicator glows orange when data is being exchanged
indicator (orange) between the computer and the LAN.
Link indicator This indicator glows green when the computer is connect-
(green) ed to a LAN and the LAN is functioning properly.
LAN jack This jack lets you connect to a LAN. The adaptor has
built-in support for Ethernet LAN (10 megabits per second,
Ether
10BASE-T)andFastEthernetLAN(100megabitsper
second, 100BASE-Tx). The LAN has two indicators. See
Chapter 4, Operating Basics, for details.
CAUTIONS: 1. Do not connect cables other than LAN, otherwise it
causes a failure or damage.
2. Do not connect equipment which supplies electric
power, otherwise it causes a failure or damage.
Universal Two Universal Serial Bus ports are on the left side.
Serial Bus The port comply with the USB 2.0 standard, which
(USB2.0)ports enables data transfer speed 40 times faster than the USB
1.1 standard. (The ports also support USB 1.1.)
Also two ports are on the back side.
CAUTION: Keep foreign objects out of the USB connectors. A pin or
similar object can damage the computer’s circuitry.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Right side
NOTE: Operation of all functions of all USB devices has not been
confirmed. Some functions might not execute properly.
i.LINK(IEEE1394) Connect an external device, such as a digital video camera
port to this port for high-speed data transfer. You must connect
the AC adaptor when you use i.LINK.
PC card slot A PC card slot can accommodate one 5 mm Type II card.
You can install any industry standard PC card such as a
SCSI adaptor, Ethernet adaptor or flash memory card.
CB
CAUTION: Keep foreign objects out of the PC card slot. A pin or similar
object can damage the computer’s circuitry.
SD card indicator This indicator glows green when the computer is
accessing the SD card Slot.
SD card slot This slot lets you transfer data from the device to your
computer.
CAUTION: Keep foreign objects out of the SD card slot. A pin or similar
object can damage the computer’s circuitry.
Right side
Figure 2-3 shows the computer’s right side.
WIRELESS COMMUNICATION
INDICATOR
WIRELESS COMMUNICATION
SWITCH
HEADPHONE JACK
MICROPHONE JACK
VOLUME CONTROL FIXED OPTICAL MEDIA DRIVE
CD/DVD-IN-USE INDICATOR
MODEM JACK
Figure 2-3 The right side of the computer
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Fixed Optical The computer is configured with a full-size optical media
media drive drive module that lets you run either 12 cm (4.72") or 8 cm
(3.15") disks without using an adaptor. Refer to the Fixed
Optical media drive section in this chapter for technical
specifications on each drive and to Chapter 4, Operating
Basics, for information on using the drive and caring for
disks.
Thefollowingdrivesareavailable:
• DVD-ROMdrive
• CD-RW/DVD-ROMdrive
• DVD-R/-RWdrive
• DVDMultidrive
• DVD±RWdrive
Modem jack In areas where an internal modem is installed as standard
equipment, there is a modem jack that lets you use a
modular cable to connect the modem directly to a tele-
phone line.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
Volume control Use this dial to adjust the volume of the stereo speakers or
the stereo headphones.
Wireless Slide this switch toward the left of the computer to turn
communication off Wireless LAN function. Slide it toward the right of
switch the computer to turn on the functions (Wireless LAN
modelonly).
CAUTION: Set the switch to off in airplanes and hospitals. Check the
wireless communication indicator. It will stop glowing when the wireless
communication function is off.
Wireless This indicator glows orange when Wireless LAN function
communication is on (Wireless LAN model only.)
Indicator
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Back side
Microphone jack A standard 3.5 mm mini microphone jack enables connec-
tion of a monaural microphone or other device for audio
input. When you connect an external microphone, the
internal microphone is automatically disabled.
Headphone jack A standard 3.5 mm mini headphone jack enables connec-
tion of a stereo headphone (16 ohm minimum) or other
device for audio output. When you connect headphones,
the internal speakers are automatically disabled.
CD/DVD-in-use This indicator glows green when the computer is
indicator accessing a diskette in the diskette drive or a disk in the
DVD-ROM, CD-RW/DVD-ROM, DVD-R/-RW,DVDMulti
orDVD±RWdrive.
Back side
Figure 2-4 shows the computer’s back side.
DC IN 15V
SECURITY LOCK
PARALLEL
PORT
COOLING VENTS
USBPORTS
EXTERNAL MONITOR PORT
Figure 2-4 The back side of the computer
Parallel port This Centronics-compatible, 25-pin parallel port that is used
to connect a parallel printer or other parallel device. This
port supports Extended Capabilities Port (ECP) standard.
External monitor This 15-pin port lets you connect an external monitor.
port
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Universal Two Universal Serial Bus ports are on the back side.
Serial Bus The port comply with the USB 2.0 standard, which
(USB2.0)ports enables data transfer speed 40 times faster than the USB
1.1 standard. (The ports also support USB 1.1.)
Also two ports are on the left side.
Security lock A security cable attaches to this slot. The optional
security cable anchors your computer to a desk or other
large object to deter theft.
CAUTIONS: 1. Keep foreign objects out of the USB connectors. A pin
or similar object can damage the computer’s circuitry.
2. The Security Lock Slot is between Cooling Vent. After
using this computer, the Security Lock Slot is hot
because of the exhaust heat from the Cooling Vent.
There is a possibility of getting burnt when the
Security Lock Slot is touched at this time. Therefore,
be careful enough work after it is confirmed that heat
is cold enough after the computer is used.
NOTE: Operation of all functions of all USB devices has not been
confirmed. Some functions might not execute properly.
DC IN 15V The AC adaptor connects to this socket. Use only the
model of AC adaptor that comes with the computer. Using
DC IN 15V
the wrong adaptor can damage your computer.
Coolingvents These vents provide an outlet for air pulled through the
computer by the fan.
CAUTION: Be careful not to block the cooling vents. Also be careful to
keep foreign objects out of them. A pin or similar object can damage the
computer’s circuitry.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Underside
Underside
Figure 2-5 shows the underside of the computer. Make sure the display is closed
before turning over your computer.
MEMORY MODULE COVER
FANVENT
BATTERY PACK
BATTERY SAFETY LOCK
BATTERY RELEASE LATCH
Figure 2-5 The underside of the computer
Battery release Slide this latch to release the battery pack for removal.
latch For detailed information on removing the battery packs,
refer to Chapter 6, Power and Power-Up Modes.
Batterysafetylock Switch this safety lock to make the battery release latch
slide freely or locked. For detailed information, refer to
Chapter 6, Power and Power-Up Modes.
Battery pack The battery pack powers the computer when the AC
adaptor is not connected. For detailed information on the
battery pack, refer to Chapter 6, Power and Power-Up
Modes.
Memory module This cover protects two memory module sockets
cover One or two modules are preinstalled. Refer to the Memory
expansion section in Chapter 8, Optional Devices.
Fan vent Provides air flow for the fan.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Front with the display open
Figure 2-6 shows the front of the computer with the display open. To open the
display, slide the display latch on the front of the display to the right of the
computer and lift up. Position the display at a comfortable viewing angle.
DISPLAY HINGE
DISPLAY SCREEN
STEREO SPEAKER
(RIGHT)
AUDIO/VIDEO CONTROL
BUTTONS*
STEREO SPEAKER
(LEFT)
SENSOR SWITCH
POWER BUTTON
(NOT SHOWN)
TOUCH PAD
TOUCH PAD CONTROL BUTTONS
Figure 2-6 The front with the display open
Display hinge The display hinge holds the display screen at easy-to-
view angles.
Displayscreen The LCD displays high-contrast text and graphics. The
computer’s LCD consists of up to 1024x768 pixels or 1400
x1050 pixels. The computer has a Thin-Film Transistor
(TFT) display. Refer to Appendix B.
When the computer operates on power through the AC
adaptor, the display screen’s image will be somewhat
brighter than when it operates on battery power. The lower
brightness level is intended to save battery power.
Stereo speakers The speakers emit sound generated by your software as
well as audio alarms, such as low battery condition,
generated by the system.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
System indicators
Audio/Video Previous
controlbuttons* data. Play/pause
button: Plays the previous track/chapter/
button: Begins or pauses play. Stop
button: Halts play. Next
button: Plays the next
track/chapter/data. Refer to Chapter 4, Operating Basics.
* Audio/Video control buttons are provided with some models.
NOTE: If Random is selected in TOSHIBA Media Player, selecting Next
or Previous advances to a random selection.
Power button Press the power button to turn the computer’s power on
and off.
Touch Pad A Touch Pad located slightly in the left from the center of
the palm rest is used to control the on-screen pointer. Refer
to the Using the Touch Pad section in Chapter 4, Operat-
ing Basics.
Touch Pad Control buttons close to the Touch Pad let you select
controlbuttons menu items or manipulate text and graphics designated by
the on-screen pointer.
Sensorswitch This switch shuts down the computer when you close the
cover and the panel power on/off feature is enabled.
System indicators
DC IN 15V
POWER
BATTERY
BUILT-INHDD
Figure 2-7 System indicators
DC IN 15V The DC IN 15V indicator glows green when DC power is
supplied from the AC power adaptor. If the adaptor’s
output voltage is abnormal or if the power supply malfunc-
tions, this indicator flashes orange.
Power The Power indicator glows green when the computer is
on. If you select Standby from Shut Down Windows,
this indicator flashes orange (one second on, two seconds
off) while the computer shuts down.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Battery The Battery indicator shows the condition of the
battery’s charge: Green indicates full charge, orange
indicates battery charging and flashing orange indicates a
low battery charge. Refer to Chapter 6, Power and Power-
Up Modes.
Built-inHDD The Built-in HDD indicator glows green when the
computer is accessing the hard disk.
Keyboard indicators
The figures below show the positions of the keypad overlay indicators and the
CapsLockindicator.
When the F10 key indicator glows the keypad overlay lets you control the cursor.
When the F11 key indicator glows the keypad overlay lets you enter numbers.
ARROW MODE
INDICATOR
NUMERIC MODE
INDICATOR
Figure 2-8 Keypad overlay indicators
Arrow mode When the Arrow mode indicator lights green, you can
use the keypad overlay (gray labeled keys) as cursor keys.
Refer to the Keypad overlay section in Chapter 5, The
Keyboard.
Numeric mode You can use the keypad overlay (gray labeled keys) for
numeric input when the Numeric mode indicator lights
green. Refer to the Keypad overlay section in Chapter 5,
The Keyboard.
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
USB diskette drive
When the CapsLock indicator glows the keyboard is in all-caps mode.
CAPSLOCK INDICATOR
Figure 2-9 CapsLock indicator
CapsLock This indicator glows green when the alphabet keys are
locked in uppercase.
USB diskette drive
A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It
connects to the USB port.
DISK-IN-USE
INDICATOR
DISKETTE SLOT
EJECT BUTTON
Figure 2-10 USB diskette drive
Disk-In-Use This indicator lights when the diskette is being accessed.
Indicator
Disketteslot Insert a diskette in this slot.
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Ejectbutton When a diskette is fully seated in the drive, the eject
button pops out. To remove a diskette, push in the eject
button and the diskette pops out partially for removal.
CAUTION: Check the Disk-In-Use indicator when you use the diskette
drive. Do not press the eject button or turn off the computer while the light is
glowing. Doing so could destroy data and damage the diskette or the drive.
NOTES: 1. The external diskette drive should be placed on a flat,
horizontal surface when in use. Do not set the drive on an
incline greater than 20o while it is operating.
2. Do not set anything on top of the diskette drive.
Fixed optical media drive
One of the following optical media drives is installed in the computer: CD-RW/DVD-
ROMdrive,DVDMultidrive,DVD-ROMdrive,DVD-R/-RWdrive,DVD±RWdrive.
An ATAPI interface controller is used for CD/DVD-ROM operation. When the
computer is accessing a CD/DVD, an indicator on the drive glows.
Region codes for DVD drives and media
CD-RW/DVD-ROM,DVDMulti,DVD-ROM,DVD-R/-RW, DVD±RWdriveand
media are manufactured according to the specifications of six marketing regions.
When you purchase DVD-Video, make sure it matches your drive, otherwise it will
not play properly.
Code
Region
1
2
3
4
Canada, United States
Japan, Europe, South Africa, Middle East
Southeast Asia, East Asia
Australia, New Zealand, Pacific Islands, Central
America,SouthAmerica,Caribbean
5
6
Russia, Indian Subcontinent, Africa, North Korea,
Mongolia
China
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Fixed optical media drive
Writable discs
This section describes the types of writable CD/DVD discs. Check the specifica-
tions for your drive to for the type of discs it can write. Use Drag'n Drop CD+DVD
to write compact discs. Refer to Chapter 4, Operating Basics.
CDs
❑ CD-R discs can be written only once. The recorded data cannot be erased or
changed.
❑ CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed
CD-RW discs or high-speed 4- to 10-speed discs. The write speed of the
ultra-speedCD-RWdiscs(Ultra-speedisCD-RW/DVD-ROMdriveonly)is
maximum24-speed.
DVDs
❑ DVD-R discs can be written only once. The recorded data cannot be erased or
changed.
❑ DVD±R, DVD+RW and DVD-RAM discs can be recorded more than once.
Formats
The drives support the following formats:
• DVD-ROM
• DVD-Video
• CD-DA
• CD-Text
• Photo CDTM (single/multi-session)
• CD-ROMXAMode 2(Form1,Form2)
• CD-G(AudioCDonly)
• CD-ROM Mode 1, Mode 2
• EnhancedCD(CD-EXTRA)
• Addressing Method 2
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
DVD-ROM drive
Thefull-sizeDVD-ROMdrivemoduleletsyourecorddatatorewritableCD/DVDs
as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an
adaptor.
NOTE: The read speed is slower at the center of a disc and faster at the
outer edge.
DVD read 8speed(maximum)
CD read 24speed(maximum)
CD-RW/DVD-ROM drive
Thefull-sizeCD-RW/DVD-ROMdrivemoduleletsyourecorddatatorewritable
CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an
adaptor.
NOTE: The read speed is slower at the center of a disc and faster at the
outer edge.
DVD read 8speed(maximum)
CD read 24speed(maximum)
CD-Rwrite 24speed(maximum)
CD-RW write 10speed(maximum,high-speedmedia)
DVD-R/-RW drive
Thefull-sizeDVD-R/-RWdrivemoduleletsyourecorddatatorewritableCD/DVDs
aswellasruneither12cm(4.72")or8cm(3.15")CD/DVDswithoutusingan
adaptor.
NOTE: The read speed is slower at the center of a disc and faster at the
outer edge.
DVD read 8speed(maximum)
DVD-R write 2 speed
DVD-RW write 1 speed
CD read 24speed(maximum)
CD-Rwrite 16speed(maximum)
CD-RW write 10speed(maximum)
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Fixed optical media drive
DVD Multi drive
The full-size DVD Multi drive module lets you record data to rewritable CD/DVDs as
well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.
NOTE: The read speed is slower at the center of a disc and faster at the
outer edge.
DVD read 8speed(maximum)
DVD-R write 2 speed
DVD-RW write 1 speed
DVD-RAMwrite 2 speed
CD read 24speed(maximum)
CD-Rwrite 16speed(maximum)
CD-RW write 8speed(maximum,high-speedmedia)
DVD±RW drive (DVD Dual drive)
Thefull-sizeDVD±RWdrivemoduleletsyourecorddatatorewritableCD/DVDs
aswellasruneither12cm(4.72")or8cm(3.15")CD/DVDswithoutusingan
adaptor.
NOTE: The read speed is slower at the center of a disc and faster at the
outer edge.
DVD read 8speed(maximum)
DVD-R write 2speed(maximum)
DVD-RW write 2speed(maximum)
DVD+R write 2.4speed(maximum)
DVD+RW write 2.4speed(maximum)
CD read 24speed(maximum)
CD-Rwrite 16speed(maximum)
CD-RW write 10speed(maximum,high-speedmedia)
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
AC adaptor
The AC adaptor converts AC power to DC power and reduces the voltage supplied
to the computer. It can automatically adjust to any voltage from 100 to 240 volts and
to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost
any country/region.
To recharge the battery, simply connect the AC adaptor to a power source and the
computer. See Chapter 6, Power and Power-Up Modes for details.
Figure 2-11 The AC adaptor
CAUTION: Use only the AC adaptor that came with the computer or an
equivalent optional adaptor. Use of the wrong adaptor could damage
your computer. TOSHIBA assumes no liability for any damage in such
case.
WARNING: Use only the AC adaptor supplied as an accessory. Other
AC adaptors have different voltage and terminal polarities and use of
them may produce heat and smoke or even result in fine or rupture.
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Getting Started
Setting up your work space .............................................................. 3-1
Generalconditions.............................................................................. 3-2
Placement of the computer ................................................................. 3-2
Seatingandposture ........................................................................... 3-3
Lighting .............................................................................................. 3-4
Work habits ........................................................................................ 3-4
Connecting the AC adaptor .............................................................. 3-5
Opening the display .......................................................................... 3-6
Turning on the power ....................................................................... 3-7
Starting up for the first time.............................................................. 3-8
Turning off the power ....................................................................... 3-8
Shut Down mode (Boot mode) ............................................................ 3-8
Hibernationmode ............................................................................... 3-9
Standbymode .................................................................................. 3-11
Restarting the computer ................................................................. 3-13
Restoring the preinstalled software from
the Product Recovery DVD-ROM .................................................... 3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Getting Started
This chapter provides basic information to get you started using your computer. It
covers the following topics:
❑
Setting up your work space — for your health and safety
NOTE: Be sure also to read Instruction Manual for Safety & Comfort.
This guide, which is included with the computer, explains product
liability.
❑
❑
❑
❑
❑
❑
❑
Connecting the AC adaptor
Opening the display
Turning on the power
Starting up for the first time
Turning off the power
Restarting the computer
Restoring the preinstalled software from the Product Recovery DVD-ROM
If you are a new user, follow the steps in each section of this chapter as you prepare
to operate your computer.
NOTE: All users should be sure to carefully read the section Starting up
for the first time, which describe actions to take when you turn on the
power for the first time.
Setting up your work space
Establishing a comfortable work site is important for you and your computer. A
poor work environment or stressful work habits can result in discomfort or serious
injury from repetitive strain to your hands, wrists or other joints. Proper ambient
conditions should also be maintained for the computer’s operation. This section
discusses the following topics:
❑
❑
General conditions
Placement of the computer
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
❑
❑
❑
Seating and posture
Lighting
Work habits
General conditions
In general, if you are comfortable, so is your computer, but read the following to
make sure your work site provides a proper environment.
❑
❑
Make sure there is adequate space around the computer for proper ventilation.
Make sure the AC power cord connects to an outlet that is close to the
computer and easily accessible.
❑
❑
The temperature should be 5 C to 35 C (41 F to 95 F) and the relative humidity
should be 20 to 80 percent.
Avoid areas where rapid or extreme changes in temperature or humidity may
occur.
❑
❑
❑
❑
Keep the computer free of dust, moisture, and exposure to direct sunlight.
Keep the computer away from heat sources, such as electric heaters.
Do not use the computer near liquids or corrosive chemicals.
Do not place the computer near objects that create strong magnetic fields (e.g.,
stereo speakers).
❑
Some computers in the computer, including data storage media, can be
damaged by magnets. Do not place the computer near magnetic objects or
bring magnetic objects close to the computer. Be careful of objects, such as
stereo speakers, that produce strong magnetic fields during operation. Also, be
careful with metal objects, such as bracelets, which can be inadvertently
magnetized.
❑
❑
Do not operate the computer in close proximity to a mobile phone.
Leave ample ventilation room for the fan. Do not block the vents.
Placement of the computer
Position the computer and peripheral devices to provide comfort and safety.
❑
❑
Set the computer on a flat surface at a comfortable height and distance. The
display should be no higher than eye level to avoid eye strain.
Place the computer so that it is directly in front of you when you work and
make sure you have adequate space to easily operate other devices.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your work space
❑
❑
Allow adequate space behind the computer to let you freely adjust the display.
The display should be angled to reduce glare and maximize visibility.
If you use a paper holder, set it at about the same height and distance as the
computer.
Seating and posture
The height of your chair in relation to the computer and keyboard as well as the
support it gives your body are primary factors in reducing work strain. Refer to the
following tips and to figure 3-1.
BELOW EYE LEVEL
O
90 ANGLES
FOOT REST
Figure 3-1 Posture and positioning of the computer
❑
❑
Place your chair so that the keyboard is at or slightly below the level of your
elbow. You should be able to type comfortably with your shoulders relaxed.
Your knees should be slightly higher than your hips. If necessary, use a foot
rest to raise the level of your knees to ease pressure on the back of your thighs.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
❑
❑
Adjust the back of your chair so it supports the lower curve of your spine.
Sit straight so that your knees, hips and elbows form approximately 90 degree
angles when you work. Do not slump forward or lean back too far.
Lighting
Proper lighting can improve legibility of the display and reduce eye strain.
❑
Position the computer so that sunlight or bright indoor lighting does not reflect
off the screen. Use tinted windows, shades or other screen to eliminate sun
glare.
❑
❑
Avoid placing the computer in front of bright light that could shine directly in
your eyes.
If possible, use soft, indirect lighting in your computer work area. Use a lamp to
illuminate your documents or desk, but be sure to position the lamp so that it
does not reflect off the display or shine in your eyes.
Work habits
A key to avoiding discomfort or injury from repetitive strain is to vary your activi-
ties. If possible, schedule a variety of tasks into your work day. If you must spend
long periods at the computer, finding ways to break up the routine can reduce
stress and improve your efficiency.
❑
Sit in a relaxed posture. Good positioning of your chair and equipment as
described earlier can reduce tension in your shoulders or neck and ease back
strain.
❑
❑
❑
❑
Vary your posture frequently.
Occasionally stand up and stretch or exercise briefly.
Exercise and stretch your wrists and hands a number of times during the day.
Frequently, look away from the computer and focus your eyes on a distant
object for several seconds, for example 30 seconds every 15 minutes.
❑
❑
Take frequent short breaks instead of one or two long breaks, for example, two
or three minutes every half hour.
Have your eyes examined regularly and visit a doctor promptly, if you suspect
you might be suffering from a repetitive strain injury.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the AC adaptor
A number of books are available on ergonomics and repetitive strain injury or
repetitive stress syndrome. For more information on these topics or for pointers on
exercises for such stress points as hands and wrists, please check with your library
or book vendor. Also refer to the computer’s Instruction Manual for Safety &
Comfort.
Connecting the AC adaptor
Attach the AC adaptor when you need to charge the battery or you want to operate
from AC power. It is also the fastest way to get started, because the battery pack
will need to be charged before you can operate from battery power.
The AC adaptor can be connected to any power source supplying from 100 to 240
volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery
pack, refer to Chapter 6, Power and Power-Up Modes.
WARNING: Use only the AC adaptor supplied as an accessory. Other
AC adaptors have different voltage and terminal polarities and use of
them may produce heat and smoke or even result in fine or rupture.
CAUTIONS:
1. Use only the AC adaptor supplied with your
computer or an equivalent adaptor that is
compaible. Use of any incompatible adaptor could
damage your computer. TOSHIBA assumes no
liability for any damage caused by use of an
incompatible adaptor.
2. When you connect the AC adaptor to
the computer, always follow the steps in the exact
order as described in the User’s Manual.
Connecting the power cable to a live electrical
outlet should be the last step otherwise the
adaptor DC output plug could hold an electrical
change and cause an electrical shock or minor
bodily injury when touched. As a general safety
precaution, avoid touching any metal parts.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
1. Connect the power cord to the AC adaptor.
Figure 3-2 Connecting the power cord to the AC adaptor
2. Connect the AC adaptor’s DC output plug to the DC IN 15V input port on the
back of the computer.
DC IN 15V
Figure 3-3 Connecting the adaptor to the computer
3. Plug the power cord into a live wall outlet. The Battery and DC IN 15V
indicators on the front of the computer should glow.
Opening the display
The display panel can be rotated in a wide range of angles for optimal viewing.
1. Slide the display latch on the front of the computer to the right to unlatch the
display panel.
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the power
2. Lift the display panel up and adjust it to the best viewing angle for you.
CAUTION: Use reasonable care when opening and closing the display
panel. Opening it vigorously or slamming it shut could damage the
computer.
NOTE: When you open the display, hold it with both hands and lift up
slowly.
DISPLAY LATCH
Figure 3-4 Opening the display panel
Turning on the power
This section describes how to turn on the power.
NOTE: After you turn on the power for the first time, do not turn it off
until you have set up the operating system. Refer to the section Starting
up for the first time in this chapter.
1. If the external diskette drive is connected, make sure it is empty. If a diskette is
in the drive, press the eject button and remove the diskette.
2. Open the display.
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
3. Press and hold the computer’s power button for two or three seconds.
POWER BUTTON
Figure 3-5 Turning on the power
Starting up for the first time
When you first turn on the power, the computer’s initial screen is the Microsoft
Windows XP Startup Screen Logo. Follow the on-screen directions for each screen.
During setup, you can click the Back button to return to the previous screen.
Be sure to read the Windows End User License Agreementdisplay
carefully.
NOTE: Be sure to read the License Agreement carefully.
Turning off the power
The power can be turned off in one of the following modes: Shut down (Boot),
Hibernation or Standby mode.
Shut Down mode (Boot mode)
When you turn off the power in Shut Down mode no data is saved and the
computer will boot to the operating system’s main screen.
1. If you have entered data, save it to the hard disk or to a diskette.
2. Make sure all disk (disc) activity has stopped, then remove the CD/DVDs or
diskette.
CAUTION: Make sure the Built-in HDD and CD/DVD-in-use indicators
are off. If you turn off the power while a disk (disc) is being accessed, you
can lose data or damage the disk (disc).
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning off the power
3. Click start then click Turn Off Computer. From the Turn Off Com-
putermenu select Turn Off.
4. Turn off the power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately. Wait
a moment to let all capacitors fully discharge.
Hibernation mode
The hibernation feature saves the contents of memory to the hard disk when the
computer is turned off. The next time the computer is turned on, the previous state
is restored. The hibernation feature does not save the status of peripheral devices.
CAUTIONS: 1. Save your data. While entering hibernation mode, the
computer saves the contents of memory to the HDD.
However, for safety sake, it is best to save your data
manually.
2. Data will be lost if you remove the battery or discon-
nect the AC adaptor before the save is completed. Wait
for the Built-IN HDD indicator to go out.
3. Do not install or remove a memory module while the
computer is in hibernation mode. Data will be lost.
Benefits of hibernation
The hibernation feature provides the following benefits:
❑
Saves data to the hard disk when the computer automatically shuts down
because of a low battery.
NOTE: For the computer to shut down in hibernation mode, the hiberna-
tion feature must be enabled in two places : the hibernate tab in Power
Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the
computer will shut down in Standby mode. If battery power becomes
depleted, data saved in Standby will be lost.
❑
❑
❑
You can return to your previous working environment immediately when you
turn on the computer.
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System hibernate feature.
You can use the panel power off feature.
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Starting Hibernation
NOTE: You can also enable Hibernation by pressing Fn + F4. See
Chapter 5, The Keyboard, for details.
To enter Hibernation mode, follow the steps below.
1. ClickStart.
2. Select Turn Off Computer.
3. Open the Turn Off Computer dialog box. Hibernateis not displayed.
4. Press the Shift key. The Standbyitem will change to Hibernate.
5. Select Hibernate.
Automatic Hibernation
The computer will enter Hibernate mode automatically when you press the power
button or close the lid. First, however, make the appropriate settings according to
the steps below.
1. Open the Control Panel.
2. Open Performance and Maintenance and open Power Options.
3. Select the Hibernate window, in Power Option property select the Enable
Hibernation check box and click the Apply button.
4. Open TOSHIBA Power Saver.
5. Select the Setup Action window.
6. Enable the desired Hibernation settings for When I press the power
button and When I close the lid.
7. Click the OK button.
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning off the power
Data save in hibernation mode
When you turn off the power in hibernation mode, the computer takes a moment to
save current memory data to the hard disk. During this time, the Built-IN HDD
indicatorwilllight.
After you turn off the computer and memory is saved to the hard disk, turn off the
power to any peripheral devices.
CAUTION: Do not turn the computer or devices back on immediately.
Wait a moment to let all capacitors fully discharge.
Standby mode
If you have to interrupt your work, you can turn off the power without exiting from
your software. Data is maintained in the computer’s main memory. When you turn
on the power again, you can continue working right where you left off.
NOTES: 1. When the AC adaptor is connected, the computer will go
into Standby mode according to the settings in the
TOSHIBA Power Saver utility.
2. To restore operation from Standby mode, press the power
button or press any key. The latter action works only if
Wake-up on Keyboard is enabled in HW Setup.
3. If the computer automatically enters Standby mode while a
network application is active, the application might not be
restored when the computer wakes up from Standby.
4. To prevent the computer from automatically entering
Standby mode, disable Standby in TOSHIBA Power Saver.
That action, however, will nullify the computer’s Energy
Star compliance.
CAUTIONS: 1. Before entering Standby mode, be sure to save your data.
2. Do not install or remove a memory module while the
computer is in standby mode. The computer or the
module could be damaged.
3. Do not remove the battery pack while the computer is in
standby mode (unless the computer is connected to an
AC power source). Data in memory will be lost.
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
4. If you carry the computer on board an aircraft or into a
hospital, be sure to shut down the computer in hiberna-
tion mode or in shutdown mode to avoid radio signal
interference.
Benefits of standby
The standby feature provides the following benefits:
❑
❑
❑
Restores the previous working environment more rapidly than does hiberna-
tion.
Saves power by shutting down the system when the computer receives no
input or hardware access for the duration set by the System Standby feature.
You can use the panel power off feature.
Executing standby
NOTE: You can also enable Standby by pressing Fn + F3. See Chapter
5, The Keyboard, for details.
You can enter standby mode in one of three ways:
1. Clickstart,clickTurnOffComputerandclickStandby.
2. Close the display panel. This feature must be enabled. Refer to the Setup
Action tab in Power Saver Utility described in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power
Saver.
3. Press the power button. This feature must be enabled. Refer to the Setup
Action tab in Power Saver Utility described in the Control Panel.
Open Performance and Maintenance and open TOSHIBA Power
Saver.
When you turn the power back on, you can continue where you left when you shut
down the computer.
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Restarting the computer
NOTES: 1. When the computer is shut down in standby mode, the
power indicator flashes orange.
2. If you are operating the computer on battery power, you
can lengthen the operating time by shutting down in
hibernation mode. Standby mode consumes more power.
Standby limitations
Standby will not function under the following conditions:
❑
❑
Power is turned back on immediately after shutting down.
Memory circuits are exposed to static electricity or electrical noise.
Restarting the computer
Certain conditions require that you reset the system. For example, if:
❑
❑
You change certain computer settings.
An error occurs and the computer does not respond to your keyboard
commands.
There are three ways to reset the computer system:
1. Click start then click Turn off computer. From the Turn off com-
putermenu select Restart.
2. Press Ctrl + Alt + Del to display the Windows Task Manager, and
then select Shutdown and Restart.
3. Select Restart from the Turn Off Computerwindow in the start
menu.
4. Press the power button and hold it down for five seconds. Wait 10 to 15
seconds, and then turn the power on again by pressing the power button.
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Restoring the preinstalled software
from the Product Recovery DVD-ROM
If preinstalled files are damaged, use the Product Recovery DVD-ROM to restore
them. To restore the operating system and all preinstalled software, follow the steps
below.
CAUTION: When you reinstall the Windows operating system, the hard
disk will be reformatted and all data will be lost.
1. Load the Product Recovery DVD-ROM in the fixed optical media drive and
turn off the computer’s power.
2. Hold down the F12 key and turn on the power. When In Touch with
Tomorrow TOSHIBAappears, release the F12 key.
3. Use the left or right cursor key to select the DVD-ROM icon in the display
menu. For details, refer to the Boot priority section in Chapter 7, HW Setup
and Passwords.
4. Follow the on-screen instructions.
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Operating Basics
Using the Touch Pad ......................................................................... 4-1
Using the USB diskette drive ............................................................ 4-2
Connecting 3 1/2" diskette drive ......................................................... 4-2
Disconnecting 3 1/2" diskette drive ..................................................... 4-3
Using optical media drives ............................................................... 4-3
Loading discs ..................................................................................... 4-4
Removingdiscs .................................................................................. 4-6
Audio/Videocontrols ......................................................................... 4-7
Next and Previous buttons .................................................................. 4-7
Play/Pause and Stop buttons ............................................................. 4-8
Controls for CD/DVD and Digital Audio ............................................... 4-8
Writing CDs on CD-RW/DVD-ROM drive ........................................... 4-8
Beforewritingorrewriting.................................................................... 4-9
Writing CD/DVDs on DVD±RW drive (DVD Dual drive) .................. 4-10
Importantmessage ........................................................................... 4-10
Disclaimer ........................................................................................ 4-10
Writing CD/DVDs on DVD-R/-RW drive ........................................... 4-11
Importantmessage ........................................................................... 4-11
Disclaimer ........................................................................................ 4-11
Writing CD/DVDs on DVD Multi drive ............................................. 4-12
Importantmessage ........................................................................... 4-12
Disclaimer ........................................................................................ 4-12
Beforewritingorrewriting.................................................................. 4-12
Drag’nDropCD+DVD ....................................................................... 4-15
Dataverification ................................................................................ 4-16
Media care ....................................................................................... 4-16
CD/DVDs.......................................................................................... 4-16
Diskettes .......................................................................................... 4-17
Sound System .................................................................................. 4-17
Volumecontrol ................................................................................. 4-17
Microphonelevel ............................................................................... 4-17
SoundMAXControlPanel ................................................................. 4-18
MicrophoneEnhancements .............................................................. 4-18
Powermanagement .......................................................................... 4-18
Modem.............................................................................................. 4-19
Regionselection ............................................................................... 4-19
Propertiesmenu ............................................................................... 4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting ....................................................................................... 4-21
Disconnecting................................................................................... 4-22
WirelessLAN.................................................................................... 4-22
Security............................................................................................ 4-23
Wireless communication switch ....................................................... 4-23
WirelesscommunicationIndicator .................................................... 4-24
LAN ................................................................................................... 4-24
LAN cable types ............................................................................... 4-24
ConnectingLANcable ...................................................................... 4-25
Disconnecting LAN cable ................................................................. 4-26
Cleaning the computer ................................................................... 4-26
Moving the computer ...................................................................... 4-26
Heat dispersal .................................................................................. 4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Operating Basics
This chapter gives information on basic operations including using the Touch Pad,
the external diskette drive, optical media drives, Audio/video controls, Sound
System, the internal modem, the wireless communication and LAN. It also provides
tips on caring for your computer and on heat dispersal.
Using the Touch Pad
To use the Touch Pad, simply touch and move your finger tip across it in the
direction you want the on-screen pointer to go.
TOUCH PAD
CONTROL
BUTTONS
TOUCH PAD
Figure 4-1 Touch Pad and Touch Pad control buttons
Two buttons below the keyboard are used like the buttons on a mouse pointer.
Press the left button to select a menu item or to manipulate text or graphics desig-
nated by the pointer. Press the right button to display a menu or other function
depending on the software you are using.
CAUTION: Do not press on the Touch Pad too hard or press a sharp
object such as a ball point pen against the Touch Pad. The Touch Pad
could be damaged.
For some functions, you can tap the Touch Pad instead of pressing a control
button.
Click Tap the Touch Pad once
Double-click Tap the Touch Pad twice
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Drag and drop 1. Hold down the left control button and move the cursor
to drag the item you want to move.
2. Lift your finger to drop the item where you want it.
Scroll Vertical: Move your finger up or down the right edge of
the Touch Pad.
Horizontal: Move your finger left or right along the bottom
edge of the Touch Pad.
Using the USB diskette drive
A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44-
megabyte or 720-kilobyte diskettes. Refer to Chapter 2, The Grand Tour, for more
information.
Connecting 3 1/2" diskette drive
To connect the drive, plug the diskette drive connector into a USB port. Refer to
Figure4-2.
CAUTION: Make sure the connector is back side up and properly
aligned with the socket. Do not try to force the connection, doing so can
damage the connecting pins.
USBPORT
Figure 4-2 Connecting the USB diskette drive
NOTE: If you connect the diskette drive after turning on the computer, it
will take about 10 seconds for the computer to recognize the drive. Do
not disconnect and reconnect before 10 seconds has elapsed.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using optical media drives
Disconnecting 3 1/2" diskette drive
When you have finished using the diskette drive, follow the procedures below to
disconnect it:
1. Wait for the indicator light to go out to make sure all diskette activity has
stopped.
CAUTION: If you disconnect the diskette drive or turn off the power
while the computer is accessing the drive you may lose data or damage
the diskette or the drive.
2. Click the Safety Remove Hardware icon on the Task Bar.
3. ClickDiskettedrive.
4. Pull the diskette drive connector out of the USB port.
Using optical media drives
The illustrations in this section might differ slightly from your drive, but operation is
the same for all optical media drives. The full-size drive provides high-performance
executionofCD/DVD-ROM-basedprograms.Youcanruneither12cm(4.72")or
8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used
for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an
indicator on the drive glows.
NOTE: Use the WinDVD 4 application to view DVD-Video discs.
If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs on
CD-RW/DVD-ROM drive section for precautions on writing to CDs.
If you have a DVD Multi drive, refer also to the Writing CD/DVDs on DVD Multi
drive section for precautions on writing to CDs.
If you have a DVD-R/-RW, refer also to the Writing CD/DVDs on DVD-R/-RW drive
section for precautions on writing to CDs.
If you have a DVD±RW drive, refer also to the Writing CD/DVDs on DVD±RWdrive
section for precautions on writing to CDs.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Loading discs
To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7.
1. a. When the power is on, press the eject button to open the drawer slightly.
EJECT BUTTON
Figure 4-3 Pressing the eject button
b. Pressing the eject button will not open the drawer when the drive’s power
is off. If the power is off, you can open the drawer by inserting a slender
object (about 15 mm) such as a straightened paper clip into the eject hole
just to the left of the eject button.
15mm
Diameter 1.0mm
Figure 4-4 Manual release with the eject hole
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using optical media drives
2. Pinch the drawer gently and pull until it is fully opened.
Figure 4-5 Pulling the drawer open
3. Lay the CD/DVD, label side up, in the drawer.
Figure 4-6 Inserting a CD/DVD
NOTE: When the drawer is fully opened, the edge of the computer will
extend slightly over the CD/DVD tray. Therefore, you will need to turn
the CD/DVD at an angle when you place it in the tray. After seating the
CD/DVD, however, make sure it lies flat, as shown in figure 4-6.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
CAUTIONS: 1. Do not touch the laser lens. Doing so could cause
misalignment.
2. Do not keep foreign matter from entering the drive.
Check the back edge of the tray to make sure it carries
no debris before closing the drive.
4. Press gently at the center of the CD/DVD until you feel it click into place. The
CD/DVD should lie below the top of the spindle, flush with the spindle base.
5. Push the center of the drawer to close it. Press gently until it locks into place.
CAUTION: If the CD/DVD is not seated properly when the drawer is
closed, the CD/DVD might be damaged. Also, the drawer might not open
fully when you press the eject button.
Figure 4-7 Closing the CD/DVD drawer
Removing discs
To remove the CD/DVD, follow the steps below and refer to figure 4-8.
CAUTION: Do not press the eject button while the computer is accessing
the optical media drive. Wait for the CD/DVD-in-use indicator to go out
before you open the drawer. Also, if the CD/DVD is spinning when you
open the drawer, wait for it to stop before you remove it.
1. To pop the drawer partially open, press the eject button. Gently pull the
drawer out until it is fully opened.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio/Video controls
CAUTIONS: 1. When the drawer pops open slightly, wait a moment to
make sure the CD/DVD has stopped spinning before
pulling the drawer fully open.
2. Turn off the power before you use the eject hole. If the
CD/DVD is spinning when you open the drawer, the
CD/DVD could fly off the spindle and cause injury.
2. The CD/DVD extends slightly over the sides of the drawer so you can grasp it.
Hold the CD/DVD gently and lift it out.
Figure 4-8 Removing a CD/DVD
3. Push the center of the drawer to close it. Press gently until it locks into place.
Audio/Video controls
This section describes how to use the audio/video control buttons.
Next and Previous buttons
A single button on a rocker controls the Next and Previous functions. Press on
the icon to select the desired function.
Next
Press the
icon to advances to the next track, chapter or data.
icon to advances to the previous track, chapter or data.
Previous Press the
NOTE: If Random is selected in TOSHIBA Media Player, selecting Next
or Previous advances to a random selection.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Play/Pause and Stop buttons
A single button on a rocker controls the Play/Pause and Stop functions. Press
on the icon to select the desired function.
Play/Pause Press the
icon to begin or pause play.
Stop Press the icon to stop play.
Controls for CD/DVD and Digital Audio
CD/DVD control
Os is running and you press Play/Pause.
If an audio CD is in the opticalmedia drive,TOSHIBA Media Player starts and CD
audio play begins. If a DVD is in the optical media drive, the DVD Video player
starts and DVD Video play begins.
Digital Audio control
TOSHIBA Media Player starts and Digital Audio Data play begins.
Writing CDs on CD-RW/DVD-ROM
drive
Depending on the type of drive installed, you may be able to write CDs. The CD-
RW/DVD-ROM drive lets you write as well as read CD-ROMs. Observe the
precautions in this section to ensure the best performance for writing CDs. For
information on loading and unloading CDs refer to the Using optical media drives
section.
NOTE: CD-R discs can be written to only once. CD-RW discs can be
rewritten many times.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Writing CDs on CD-RW/DVD-ROM drive
Before writing or rewriting
Please observe the following points when you write or rewrite the data.
❑
WerecommendthefollowingmanufacturersofCD-RandCD-RWmedia.
Media quality can affect write or rewrite success rates.
CD-R: TAIYOYUDENCO.,LTD.
MITSUBISHICHEMICALCORPORATION
RICOHCo., Ltd.
Hitachi Maxell Ltd.
CD-RW: MITSUBISHICHEMICALCORPORATION
RICOHCo., Ltd.
TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufac-
turers above. Operation of other media cannot be guaranteed.
❑
CD-RW can generally be rewritten about 1,000 times. However, the actual
number of rewrites is affected by the quality of the media and the way it is
used.
❑
❑
❑
Be sure to connect the universal AC adaptor when you write or rewrite.
Be sure to close all other software programs except the writing software.
Do not run software such as a screen saver which can put a heavy load on the
CPU.
❑
❑
Operate the computer at full power. Do not use power-saving features.
Do not write while virus check software is running. Wait for it to finish, then
disable virus detection programs including any software that checks files
automatically in the background.
❑
❑
Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and damage data.
Write from the computer's HDD to the CD. Do not try to write from shared
devices such as a LAN server or any other network device.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Writing CD/DVDs on DVD±RW drive
(DVD Dual drive)
You can use the DVD±RW drive to write data to either CD-R/RW or
DVD-R/-RW/+R/+RWdiscs.
The following applications for writing are supplied on CD-ROM:
Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc.,
InterVideoWinDVDCreator2Platinum, whichisaproductofInterVideo, Inc.
Important message
BeforeyouwriteorrewritetoCD-R/RWorDVD-R/-RW/+R/+RWdisc,
read and follow all setup and operating instructions in this section.
If you fail to do so, the DVD±RW drive may not function properly,
and you may fail to write or rewrite, lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
❑
❑
Damage to any CD-R/RW or DVD-R/-RW/+R/+RW disc that may be caused by
writing or rewriting with this product.
Any change or loss of the recorded contents of CD-R/RW or
DVD-R/-RW/+R/+RW disc that may be caused by writing or rewriting with this
product,
or for any business profit loss or business interruption that may be caused by
the change or loss of the recorded contents.
❑
Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you
may experience unexpected writing or rewriting errors due to disc quality or
problems with hardware devices. Also, it is a good idea to make two or more
copies of important data, in case of undesired change or loss of the recorded
contents.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Writing CD/DVDs on DVD-R/-RW drive
Writing CD/DVDs on DVD-R/-RW drive
YoucanusetheDVD-R/-RWdrivetowritedatatoeitherCD-R/RWorDVD-R/-RW
discs. The following applications for writing are supplied on CD-ROM:
Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc.,
InterVideoWinDVDCreator2Platinum, whichisaproductofInterVideo, Inc.
Important message
BeforeyouwriteorrewritetoCD-R/RWorDVD-R/-RWdisc,readandfollowall
set-up and operating instructions in this section. If you fail to do so, the DVD-R/-
RW drive may not function properly, and you may fail to write or rewrite, lose data
or incur other damage.
NOTE: Also refer to the disc-writing instructions in the next section,
Writing CD/DVDs on DVD Multi drive.
Disclaimer
TOSHIBA does not bear responsibility for the following:
❑
❑
Damage to any CD-R/RW or DVD-R/-RW disc that may be caused by writing
or rewriting with this product.
Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc
that may be caused by writing or rewriting with this product, or for any
business profit loss or business interruption that may be caused by the change
or loss of the recorded contents.
❑
Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you may
experience unexpected writing or rewriting errors due to disc quality or problems
with hardware devices. Also, it is a good idea to make two or more copies of
important data, in case of undesired change or loss of the recorded contents.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Writing CD/DVDs on DVD Multi drive
You can use the DVD Multi drive to write data to either CD-R/RW or DVD-R/-RW/-
RAM discs. The following applications for writing are supplied on CD-ROM:
Drag’n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc.,
InterVideoWinDVDCreator2Platinum,whichisaproductofInterVideo,Inc.
Important message
BeforeyouwriteorrewritetoCD-R/RWorDVD-R/-RW/-RAMdisc, readand
follow all set-up and operating instructions in this section. If you fail to do so, the
DVD Multi drive may not function properly, and you may fail to write or rewrite,
lose data or incur other damage.
Disclaimer
TOSHIBA does not bear responsibility for the following:
❑
❑
Damage to any CD-R/RW or DVD-R/-RW/-RAM disc that may be caused by
writing or rewriting with this product.
Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW/-
RAM disc that may be caused by writing or rewriting with this product, or for
any business profit loss or business interruption that may be caused by the
change or loss of the recorded contents.
❑
Damage that may be caused by using third party equipment or software.
Given the technological limitations of current optical disc writing drives, you may
experience unexpected writing or rewriting errors due to disc quality or problems
with hardware devices. Also, it is a good idea to make two or more copies of
important data, in case of undesired change or loss of the recorded contents.
Before writing or rewriting
Please observe the following points when you write or rewrite data.
❑
Based on TOSHIBA’s limited compatibility testing, we suggest the following
manufacturersofCD-R/RWandDVD-R/-RW/-RAMdisc.However,inno
event does TOSHIBA guarantee the operation, quality or performance of any
disc. Disc quality can affect write or rewrite success rates.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Writing CD/DVDs on DVD Multi drive
CD-R: TAIYOYUDENCO.,LTD.
MITSUBISHICHEMICALCORPORATION
RICOHCo., Ltd.
Hitachi Maxell Ltd.
CD-RW: MITSUBISHICHEMICALCORPORATION
RICOHCo., Ltd.
DVD-R: DVD Specifications for Recordable Disc for Gen-
eral Version 2.0
TAIYOYUDENCO.,LTD.
PIONEERVIDEOCORPORATION
MITSUBISHICHEMICALCORPORATION
DVD-RW: DVD Specifications for Re-recordable Disc for
Version 1.0 or Version 1.1
VICTORCOMPANYOFJAPAN,LIMITED
TDK Corporation
DVD+R: MITSUBISHICHEMICALCORPORATION
RICOHCo., Ltd.
DVD+RW: MITSUBISHICHEMICALCORPORATION
RICOHCo., Ltd.
*DVD-RAM: DVD Specifications for DVD-RAM Disc for Version
2.0 or Version 2.1
Matsushita Electric Industrial Co., Ltd.
*Only DVD Multi drive can use DVD-RAM.
❑
If the disc is poor in quality, dirty or damaged, writing or rewriting errors may
occur. Be careful to check the disc for dirt or dama ge before you use it.
❑
❑
❑
The actual number of rewrites to CD-RW or DVD-RW/-RAM is affected by the
quality of the disc and the way it is used.
There are two types of DVD-R: authoring and general use discs. Do not use
authoring discs. Only general use discs can be written to by a computer drive.
You can use DVD-RAM discs that can be removed from a cartridge and DVD-
RAM discs designed without a cartridge. You cannot use a disc with a 2.6 GB
single-sided capacity or 5.2 GB double-sided capacity.
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
❑
Other DVD-ROM drives for computers or other DVD players may not be able
toreadDVD-R/-RWdiscs.
❑
❑
❑
❑
You cannot overwrite data that has been previously written to a DVD-RW disc.
You cannot partially delete any data written to a DVD-RW disc.
Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part.
Data deleted (erased) from a CD-RW and DVD-RW/-RAM disc cannot be
recovered. Check the content of the disc carefully before you delete it. If
multiple drives that can write data to discs are connected, be careful not to
delete data from the wrong drive.
❑
❑
In writing to a DVD-R/-RW disc, some disc space is required for file manage-
ment, so you may not be able to write the full capacity of the disc.
Since the disc is based on the DVD standard, it will be filled with dummy data if
the written data is less than about 1 GB. Even if you write only a small amount
of data, it might take time to fill in the dummy data.
❑
Two types of DVD-R/-RW/-RAM discs are on the market: data and video. Use
a video disc to store video data. You can use video discs on a DVD recorder as
well as on your computer’s DVD-ROM drive. You cannot use data discs on a
DVDrecorder.
❑
❑
DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without
DVD-RAMDriverSoftware.
When multiple drives that can write data to discs are connected, be careful not
to write to the wrong drive.
❑
❑
Be sure to connect the universal AC adaptor before you write or rewrite.
Before you enter standby/hibernation mode, be sure to finish DVD-RAM
writing. WritingisfinishedifyoucanejectDVD-RAMmedia.
❑
❑
Be sure to close all other software programs except the writing software.
Do not run software such as a screen saver, which can put a heavy load on the
CPU.
❑
❑
Operate the computer in the full-power mode. Do not use power-saving
features.
Do not write while virus check software is running. Wait for it to finish, then
disable virus detection programs including any software that checks files
automatically in the background.
❑
Do not use hard disk utilities, including those intended to enhance HDD
access speed. They may cause unstable operation and data damage.
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Writing CD/DVDs on DVD Multi drive
❑
Write from the computer's HDD to the CD/DVD. Do not try to write from shared
devices such as a LAN server or any other network device.
Drag’n Drop CD+DVD
NotethefollowinglimitationswhenyouuseDrag’nDropCD+DVD:
❑
❑
❑
DVD-VideocannotbecreatedusingDrag’nDropCD+DVD.
DVD-Audio cannot be created using Drag’n Drop CD+DVD.
You cannot use Drag’n Drop CD+DVD’s music CD function to record music to
aDVD±RWdisc.
❑
❑
❑
❑
Do not use the DISC Backup function of Drag’n Drop CD+DVD to copy DVD-
VideoandDVD-ROMwithcopyrightprotection.
DVD-RAM disc cannot be backed up with the DISC Backup function of Drag’n
DropCD+DVD.
You cannot backup a CD-ROM or CD-R/RW to DVD±RW using the DISC
BackupfunctionofDrag’nDropCD+DVD.
YoucannotbackupDVD-ROM,DVD-VideoorDVD±RWtoCD-R/RWusing
theDISCBackupfunctionofDrag’nDropCD+DVD.
❑
❑
Drag’nDropCD+DVDcannotrecordinpacketformat.
You might not be able to use the DISC backup function of Drag’n Drop
CD+DVD to back up a DVD±RW disc that was made with other software on a
differentDVD±RWrecorder.
❑
If you add data to a DVD± R disc that you have already recorded to, you might
not be able to read the added data under some circumstances. It cannot be read
in 16-bit operating systems, such as Windows 98SE and Windows ME. In
Windows NT4, you will need Service Pack 6 or later to read added data. In
Windows 2000, you will need Service Pack 2 or Later to read added data. Some
DVD-ROM and CD-RW/DVD-ROM drives cannot read added data regardless
of the operating system.
❑
❑
Drag’n Drop CD+DVD does not support recording to DVD-RAM discs. To
recordtoaDVD-RAM, useExplorerorotherutility.
If you try to back up a DVD disc to a DVD-RW disc that was erased by the
Quick erase option, you might get a error message. Use the Full erase option to
clear the DVD-RW disc and try again.
❑
When you back up a DVD disc, be sure the source drive supports recording to
DVD±RW discs. If the source drive does not support recording to DVD±RW
discs, it might not be backed up correctly.
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Data verification
To verify that data is written or rewritten correctly, follow the steps below before
youwriteorrewriteaDataCD/DVD.
1. Right-click Data BOX and select Options to display the DATA DISC
Optionwindow.
2. Mark the Record and Verify check box and select Byte compare.
3. Click the OK button.
The “Record and Verify” function automatically checks whether data has been
correctly recorded onto a CD/DVD. “Byte compare” compares the original data file
with the data recorded on the CD/DVD and checks that the data completely
matches.
Media care
This section provides tips on protecting data stored on your CD/DVDs and
diskettes.
Handle your media with care. The following simple precautions will increase the
lifetime of your media and protect the data stored on them:
CD/DVDs
1. Store your CD/DVDs in the container they came in to protect them and keep
themclean.
2. Do not bend the CD/DVD.
3. Do not write on, apply a sticker to, or otherwise mar the surface of the
CD/DVD that contains data.
4. Hold the CD/DVD by its outside edge or the edge on the center hole. Finger-
prints on the surface can prevent the drive from properly reading data.
5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy
objects on your CD/DVDs.
6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth.
Wipe from the center out, do not wipe in a circular direction around the CD/
DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not
use benzine, thinner or similar cleaner.
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound System
Diskettes
1. Store your diskettes in the container they came in to protect them and keep
them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft
damp cloth.
2. Do not slide back the diskette’s protective metal covering or touch the
diskette’s magnetic surface. Fingerprints may prevent the diskette drive from
reading data from the diskette.
3. Data may be lost if the diskette is twisted; bent; or exposed to direct sunlight,
extremeheatorcold.
4. Do not place heavy objects on your diskettes.
5. Do not eat, smoke, or use erasers near your diskettes. Foreign particles inside
the diskette’s jacket can damage the magnetic surface.
6. Magnetic energy can destroy data on diskettes. Keep your diskettes away
from speakers, radios, television sets and other sources of magnetic fields.
Sound System
This section describes audio controls including sound levels and power manage-
ment.
Volume control
The Volume Control utility lets you control the audio volume in Windows for both
playback and recording.
❑
❑
❑
To launch Volume Control for playback, click Start, point to All Programs,
point to Accessories, point to Entertainment and click Volume Control.
To launch Recording Control, click Options, point to Properties, choose
RecordingandclickOK.
To view details of the Volume Control, click Helpon the Volume Control.
Microphone level
The change the microphone gain, follow the steps below if you connect an external
microphone to a microphone jack.
NOTE: You need to purchase an optional external microphone if you
would like to use the microphone functions.
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
1. Click Start, point to All Programs, point to Accessories, point to Enter-
tain ment and click Volume Control.
2. Click Properties, check the Microphonecheckbox and click OK.
3. ClickOptionsandselectAdvancedControls.
4. ClickAdvanced.
5. ChecktheMICBoostcheckboxandclickClose.
SoundMAX Control Panel
The SoundMAX control panel lets you control additional functions for the
Microphone Enhancement and Audio Power Management. To launch the
SoundMAX Control Panel, follow the steps below.
1. Click Startand click Control Panel.
2. If you are viewing the Control Panel in Category View, click on Switch to
Classic View.
3. Double-clicktheSoundMAXicon.
Microphone Enhancements
The Microphone Setup allows you to optimize the microphone input settings for
your particular configuration. Choose Standard Microphone if you have an
ordinary desktop microphone. Choose Headset if you have a wearable micro-
phone that is positioned directly in front of your mouth.
You can launch the Setup Wizard from the Control Panel to help you to automati-
cally set proper microphone input volumes and ensure that your voice input(s) are
working correctly. As you speak into the microphone, the Sound Meter indicates
the audio signal that your PC is receiving.
The Noise Reduction enhancement helps to eliminate ambient noise from the
voice input signal to provide a clean and clear signal to applications. This feature
can be used with any microphone.
Power management
The audio controller can be powered down when the audio function is idle. To
enable the Audio Power Management, follow the steps below.
1. Clicked the Power Management tab.
2. Select the Normal Power Savings in the Power Mode pull-down list.
NOTE: If the No Power Savings is selected, the audio controller always
runs.
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem
If you want to a more effect for the power management, you can select another
mode, the High Power Savings which can save the power than the Normal
Power Savings. To select it, follow the steps below.
1. Clicked the Power Management tab.
2. Select the High Power Savings in the Power Mode pull-down list.
3. Input a time in Power Save Delay (Seconds).
NOTE: If the High Power Saving is selected, you need to play an audio
file once before you use a microphone or play an audio CD by the
analog CD audio.
Modem
This section describes how to connect and disconnect the internal modem to and
from a telephone jack.
NOTE: The internal modem does not support voice functions. All data
and fax functions are supported.
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
Region selection
Telecommunication regulations vary from one region to another, so you will need to
make sure the internal modem’s settings are correct for the region in which it will be
used.
To select a region, follow the steps below.
1. Click start, point to All Programs, point to TOSHIBA point to Network-
ing and click Modem Region Select.
NOTE: Do not use the Country/Region Select function in the Modem
setup utility in the Control Panel if the function is available. If you
change the Country/Region in the Control Panel, the change may not
take effect.
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
2. The Region Selection icon will appear in the Windows Task Bar.
Figure 4-9 The Region Selection icon
3. Click the icon with the primary mouse button to display a list of regions that
the modem supports. A sub menu for telephony location information will also
be displayed. A check will appear next to the currently selected region and
telephony location.
4. Select a region from the region menu or a telephony location from the sub-
menu.
• When you click a region it becomes the modem’s region selection, and the
New Location for telephony will be set automatically.
• When you select a telephony location, the corresponding region is automati-
cally selected and it becomes the modem’s current region setting.
Properties menu
Click the icon with the secondary mouse button to display the following menu on
the screen.
Figure 4-10 The menu list
4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Modem
Setting
You can enable or disable the following settings:
AutoRunMode
The Region Select utility starts automatically when you start up the operating
system.
Open the Dialing Properties dialog box after selecting region.
The dialing properties dialog box will be displayed automatically after you
select the region.
Location list for region selection.
A submenu appears displaying location information for telephony.
Open dialog box, if the modem and Telephony Current
Location region code do not match.
A warning dialog box is displayed if current settings for region code and
telephony location are incorrect.
Modem Selection
If the computer cannot recognize the internal modem, a dialog box is displayed.
Select the COM port for your modem to use.
Dialing Properties
Select this item to display the dialing properties.
CAUTION: If you are using the computer in Japan, the Telecommunica-
tions Business Law requires that you select Japan region mode. It is
illegal to use the modem in Japan with any other selection.
Connecting
To connect the internal modem cable, follow the steps below.
WARNING: The modular cable that comes with the computer must be
used to connect a modem. Connect the end of the modular cable with the
core to the computer.
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
CAUTIONS: 1. In case of a lightning storm, unplug the modem cable
from the telephone jack.
2. Do not connect the modem to a digital telephone line.
A digital line will damage the modem.
1. Plug one end of the modular cable into the modem jack.
2. Plug the other end of the modular cable into a telephone jack.
Figure 4-11 Connecting the internal modem
CAUTION: Do not pull on the cable or move the computer while the
cable is connected.
NOTE: If you use a storage device such as an optical media drive or
HDD connected to a 16-bit PC card, modem speed might be slow or
communication might be interrupted.
Disconnecting
To disconnect the internal modem cable, follow the steps below.
1. Pinch the lever on the connector in the telephone jack and pull out the
connector.
2. Disconnect the cable from the computer in the same manner.
3. In the same way, pull the cable’s other connector out of the computer.
Wireless LAN
The Wireless LAN is compatible with other LAN systems based on Direct Se-
quence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio
technologythatcomplieswithIEEE802.11wirelessLANstandard
(Revision A, B or G) and Turbo Mode.
4-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless LAN
❑
❑
❑
❑
Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36,
24, 18, 12, 9 and 6Mbit/s. (Revision A and G, Revision B/G, A/B/G combo type)
Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2
and 1Mbit/s. (Revision B)
AutomaticTransmitRateSelectmechanisminthetransmitrangeof108, 96.72,
48, 36, 24, 18 and 12Mbit/s. (Turbo Mode, Revision A/B/G combo type)
FrequencyChannelSelection(RevisionA/TurboMode:5GHz,RevisionB/G:
2.4GHz)
❑
❑
❑
Roamingovermultiplechannels
CardPowerManagement
Wired Equivalent Privacy (WEP) data encryption, based on the 152 bit
encryptionalgorithm.(RevisionB/G, A/B/Gcombotype)WiredEquivalent
Privacy (WEP) data encryption, based on the 128 bit encryption
algorithm.(RevisionBonlytype)
❑
Advanced Encryption Standard (AES) data encryption, based on 256bit
encryptionalgorithm.(Revision B/G, A/B/Gcombotype)
NOTE: Wake-up on LAN does not function on a Wireless LAN.
Security
1. Be sure to enable WEP (encryption) function. Otherwise your computer will
allow the illegal access by outsider through Wireless LAN to cause illegal
intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA
strongly recommend the customer to enable the WEP function.
2. TOSHIBA is not liable for the eavesdropping of data due to the use of
Wireless LAN and the damage thereof.
Wireless communication switch
You can enable or disable Wireless LAN function, with the on/off switch. No
transmission is sent or received when the switch is off. Slide the switch toward the
right of the computer to turn it on and toward the left of the computer to turn it off.
CAUTION: Set the switch to off in airplanes and hospitals. Check the
Wireless communication indicator. It will stop glowing when the wireless
communication function is off.
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Wireless communication Indicator
The wireless communication indicator indicates the status of the wireless communi-
cation functions.
Indicatorstatus Indication
Indicatoroff
Wireless communication switch is set to off.
Automaticpowerdownbecauseofoverheating.
Powermalfunction
Indicatorglows
Wireless communication switch is on.
Wireless LAN is turned on by an applica-
tion.
If you used the Task Bar to disable W-LAN, restart the computer or follow the
procedures below to enable the system to recognize W-LAN. Open or click the
following: start, Control Panel, System, Hardware Device Manager,
Network adapters, TOSHIBA Wireless LAN Mini PCI Card or Atheros
AR5001X+ Wireless Network Adapter and enable.
LAN
LAN circuits support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast
Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how
to connect/disconnect to a LAN.
LAN cable types
CAUTION: The computer must be configured properly before connecting
to a LAN. Logging onto a LAN using the computer’s default settings
could cause a malfunction in LAN operation. Check with your LAN
administrator regarding set-up procedures.
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be
sure to connect with a CAT5 cable. You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can
connect with either a CAT5 or a CAT3.
4-24
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN
Connecting LAN cable
To connect the LAN cable, follow the steps below.
CAUTIONS: 1. Connect the AC adaptor before connecting the LAN
cable. The AC adaptor must remain connected during
LAN use. If you disconnect the AC Adaptor while the
computer is accessing a LAN, the system may hang up.
2. Do not connect any other cable to the LAN's jack
except the LAN cable. Otherwise, malfunctions or
damage may occur.
3. Do not connect any power supplying device to the
LAN cable that is connected to the LAN's jack.
Otherwise, malfunctions or damage may occur.
1. Turn off the power to the computer and to all external devices connected to
the computer.
2. Plug one end of the cable into the LAN jack. Press gently until you hear the
latch click into place.
Figure 4-12 Connecting the LAN cable
3. Plug the other end of the cable into a LAN hub connector. Check with your
LAN administrator before connecting to a hub.
NOTE: When the computer is exchanging data with the LAN, the LAN
Active indicator glows orange. When the computer is connected to a
LAN hub but is not exchanging data, the Link indicator glows green.
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Disconnecting LAN cable
To disconnect the LAN cable, follow the steps below.
CAUTION: Make sure the LAN Active indicator (orange LED) is out
before you disconnect the computer from the LAN.
1. Pinch the lever on the connector in the computer’s LAN jack and pull out the
connector.
2. Disconnect the cable from the LAN hub in the same manner. Check with your
LAN administrator before disconnecting from the hub.
Cleaning the computer
To help ensure long, trouble-free operation, keep the computer free of dust and use
care with liquids around the computer.
❑
Be careful not to spill liquids into the computer. If the computer does get wet,
turn the power off immediately and let the computer dry completely before you
turn it on again.
❑
Clean the computer using a slightly damp (with water) cloth. You can use glass
cleaner on the display. Spray a small amount of cleaner on a soft, clean cloth
and wipe the screen gently with the cloth.
CAUTION: Never spray cleaner directly onto the computer or let liquid
run into any part of it. Never use harsh or caustic chemical products to
clean the computer.
❑
Remove the dust from the cooling vents on the Left side of the computer
regularly with vacuum cleaner. Refer to the Left side section in Chapter 2, The
GrandTour.
Moving the computer
The computer is designed for rugged durability. However, a few simple precautions
taken when moving the computer will help ensure trouble-free operation.
❑
Make sure all disk activity has ended before moving the computer. Check the
Built-in HDD indicator on the computer and the indicator on any external disk
drive.
❑
If a diskette is in the external disk drive, remove it.
4-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Heat dispersal
❑
If a CD/DVD is in the drive, remove it. Also make sure the drawer is securely
closed.
❑
❑
❑
❑
❑
Turn off the power to the computer.
Disconnect the AC adaptor and all peripherals before moving the computer.
Close the display. Do not pick up the computer by its display panel.
Close all port covers.
Use the carrying case when transporting the computer.
Heat dispersal
To protect from overheating, the CPU has an internal temperature sensor. If the
computer’s internal temperature rises to a certain level, the cooling fan is turned on
or the processing speed is lowered. You can select whether to control the CPU
temperature by turning on the fan first, then if necessary, lowering the CPU speed.
Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the
Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.
Maximum Turn on the fan first, then if necessary, lower the CPU
Performance processing speed.
Performance Use a combination of the fan and lowering the CPU
processing speed.
Battery optimized Lower the CPU processing speed first, then if necessary
turn on the fan.
When the CPU temperature falls to a normal range, the fan is turned off and the CPU
operation returns to standard speed.
NOTE: If the CPU temperature reaches an unacceptably high level with
either setting, the system automatically shuts down to prevent damage.
Data in memory will be lost.
4-27
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
4-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
The Keyboard
Typewriter keys ................................................................................. 5-1
F1 … F12 function keys ..................................................................... 5-2
Soft keys: Fn key combinations........................................................ 5-2
Emulating keys on enhanced keyboard .............................................. 5-2
Hotkeys.............................................................................................. 5-4
Fn Sticky key ..................................................................................... 5-6
Windows special keys ....................................................................... 5-7
Keypad overlay.................................................................................. 5-7
Turningontheoverlays ....................................................................... 5-7
Temporarilyusingnormalkeyboard(overlayon).................................. 5-8
Temporarilyusingoverlay(overlayoff) ................................................. 5-9
Temporarilychangingmodes .............................................................. 5-9
Generating ASCII characters ............................................................ 5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
The Keyboard
The computer’s keyboard layouts are compatible with a 101/102-key enhanced
keyboard. By pressing some keys in combination, all the 101/102-key keyboard
functions can be executed on the computer.
The number of keys on your keyboard depends on which country/region’s key-
board layout your computer is configured with. Keyboards for numerous languages
are available.
There are five types of keys: typewriter keys, keypad overlay, function keys, soft
keys and cursor control keys.
Typewriter keys
The typewriter keys, produce the upper- and lower-case letters, numbers, punctua-
tion marks, and special symbols that appear on the screen.
There are some differences, however, between using a typewriter and using a
computer keyboard:
❑
Letters and numbers produced in computer text vary in width. Spaces, which
are created by a “space character,” may also vary depending on line justifica-
tion and other factors.
❑
The lowercase l (el) and the number 1 (one) are not interchangeable on
computers as they are on a typewriter.
❑
❑
The uppercase O (oh) and the 0 (zero) are not interchangeable.
The Caps Lock function key locks only the alphabetic characters in upper-
case while the shift lock on a typewriter places all keys in the shifted position.
❑
The Shift keys, the Tab key, and the BkSp (backspace) key perform the
same function as their typewriter counterparts but also have special computer
functions.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
F1 … F12 function keys
The function keys, not to be confused with Fn, are the 12 keys at the top of your
keyboard. These keys function differently from other keys.
F1 through F12 are called function keys because they execute programmed
functions when pressed. Used in combination with the Fn key, keys marked with
icons execute specific functions on the computer. See the section, Soft keys: Fn key
combinations, in this chapter. The function executed by individual keys depends on
the software you are using.
Soft keys: Fn key combinations
The Fn (function) is unique to TOSHIBA computers and is used in combination
with other keys to form soft keys. Soft keys are key combinations that enable,
disable or configure specific features.
NOTE: Some software may disable or interfere with soft-key operations.
Soft-key settings are not restored by the Standby feature.
Emulating keys on enhanced keyboard
PrtSc
Scroll
lock
Pause
Break
Esc
F1
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
F2
SysReq
_
-
~
`
!
@
#
$
%
&
7
(
)
+
=
Num
Lock
*
^
PgUp
PgDn
*
.
Bk Sp
Ins
Home
End
/
2
6
8
1
3
4
5
9
0
7
8
9
{
[
}
]
Tab
Del
Q
W
E
R
T
Y
U
I
O
P
\
Home
PgUp
6
+
, ,
,
:
;
4
5
2
Enter
CapsLock
A
S
D
F
G
H
J
K
L
<
,
3
>
.
?
/
1
Shift
Z
X
C
B
N
M
Shift
V
PgDn
End
Enter
.
0
Ctrl
Alt
Alt
Ctrl
Del
Ins
Figure 5-1 A 101-key enhanced keyboard layout
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Soft keys: Fn key combinations
The keyboard is designed to provide all the features of the 101-key enhanced
keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric
keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of
the main keyboard. Since the keyboard of a portable computer is smaller and has
fewer keys, some of the enhanced keyboard functions must be simulated using two
keys instead of one on the larger keyboard.
Your software may require you to use keys that the keyboard does not have.
Pressing the Fn key and one of the following keys simulates the enhanced
keyboard’s functions.
Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the
keys with gray markings on the bottom edge become numeric keypad keys (Fn +
F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this
chapter for more information on how to operate these keys. The power on default
for both settings is off.
Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on
default is off.
Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad.
Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Hot keys
Hot keys (Fn + a function or Esc key) let you enable or disable certain features of
the computers.
Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or
off. When you press these hot keys, the current setting will change and be
displayed as an icon.
Instant security: Press Fn + F1 to blank the screen to prevent others from
accessing your data. To restore the screen and original settings, press any key or
press the Touch Pad. If a screensaver password is registered, a dialog box will
appear. Enter the screensaver password and click OK. If no password is set, the
screen will be restored when you press any key or press the Touch Pad.
Power save mode: Pressing Fn + F2 changes the power save mode.
If you press Fn + F2 in a Windows environment, the Power Save Mode is
displayed in a dialog box similar to the one below. Continue holding down Fn and
press F2 again to change the setting. You can also change this setting through the
ProfileiteminPowerSaver.
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Soft keys: Fn key combinations
Standby: When you press Fn + F3, the computer enters Standby. To avoid
entering Standby unexpectedly, a dialog box appears for verification. However, if
you select the check box, it will not appear in the future.
Hibernation: When you press Fn + F4, the computer enters Hibernation. To
avoid entering Hibernation unexpectedly, a dialog box appears for verification.
However, if you select the check box, it will not appear in the future.
Display selection: Press Fn + F5 to change the active display device. When you
press these hot keys, a dialog box appears. Only selectable devices will be dis-
played. Hold down Fn and press F5 again to change the device. When you release
Fn and F5, the selected device will change. If you hold down these hot keys for five
seconds the selection will return to LCD.
LCD Display Brightness: Pressing Fn + F6 decreases the display brightness in
decrements. When you press these hot keys, the current setting will be displayed
for two seconds by an icon. You can also change this setting through the Screen
brightness item of the Basic Setup tab in Power Saver.
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
LCD Display Brightness: Pressing Fn + F7 increases the display brightness in
increments. When you press these hot keys, the current setting will be displayed
for two seconds by a pop-up icon. You can also change this setting through the
Screen brightness item of the Basic Setup tab in Power Saver.
NOTE: Display clarity increases with the brightness level.
Wireless setting: If your computer has wireless LAN functions, you can press
Fn + F8 to select which type of wireless communication you want to use. When
you press these hot keys, a dialog box will appear. Continue holding down Fn and
press F8 to change the setting. If wireless communication is turned off, Disabled
Wireless Communication Switchwill be displayed.
NOTE: If no wireless communication device is installed, no dialog box
will appear.
Touch Pad: Pressing Fn + F9 in a windows environment enables or disables the
Touch Pad function. When you press these hot keys, the current setting will
change and be displayed as an icon.
Fn Sticky key
You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is,
you can press it once, release it, and then press an “F number” key. To start the
TOSHIBA Accessibility Utility, click start, point to All Programs, point to
TOSHIBA,pointtoUtilitiesandclickAccessibility.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows special keys
Windows special keys
The keyboard provides two keys that have special functions in Windows : one
activates the start menu and the other has the same function as the secondary
mouse button.
This key activates the Windows start menu.
This key has the same function as the secondary mouse button.
Keypad overlay
Your computer’s keyboard does not have an independent numeric keypad, but its
numeric keypad overlay functions like one.
The keys in the center of the keyboard with gray letters make up the numeric
keypad overlay. The overlay provides the same functions as the numeric keypad
on the 101/102-key enhanced keyboard in figure 5-2.
Turning on the overlays
The numeric keypad overlay can be used for numeric data input or cursor and page
control.
Arrow mode
To turn on the Arrow mode, press Fn + F10. The Arrow mode F10 indicator
lights. Now try cursor and page control using the keys shown in figure 5-2. Press
Fn + F10 again to turn off the overlay.
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Numeric mode
To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator
lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11
again to turn off the overlay.
Figure 5-2 The numeric keypad overlay
Temporarily using normal keyboard
(overlay on)
While using the overlay, you can temporarily access the normal keyboard without
turning off the overlay:
1. Hold Fn and press any other key. All keys will operate as if the overlay were
off.
2. Type upper-case characters by holding Fn + Shift and pressing a character
key.
3. Release Fn to continue using the overlay.
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Generating ASCII characters
Temporarily using overlay (overlay off)
While using the normal keyboard, you can temporarily use the keypad overlay
without turning it on:
1. Press and hold down Fn.
2. Check the keyboard indicators. Pressing Fn turns on the most recently used
overlay. If the Numeric mode indicator lights, you can use the overlay for
numeric entry. If the Arrow mode indicator lights, you can use the overlay for
cursor and page control.
3. Release Fn to return to normal keyboard operation.
Temporarily changing modes
If the computer is in Numeric mode, you can switch temporarily to Arrow
mode by pressing a shift key.
If the computer is in Arrow mode, you can switch temporarily to Numeric
mode by pressing a shift key.
Generating ASCII characters
Not all ASCII characters can be generated using normal keyboard operation. But,
you can generate these characters using their ASCII codes.
With the overlay on:
1. Hold down Alt.
2. Using the overlay keys, type the ASCII code.
3. Release Alt, and the ASCII character appears on the display screen.
With the overlay off:
1. Hold down Alt + Fn.
2. Using the overlay keys, type the ASCII code.
3. Release Alt + Fn, and the ASCII character appears on the display screen.
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Power and Power-Up Modes
Power conditions................................................................................ 6-1
Power indicators ................................................................................ 6-2
Battery indicators.............................................................................. 6-2
DC IN 15V indicator .......................................................................... 6-3
Power indicator ................................................................................. 6-3
Battery types ....................................................................................... 6-3
Battery pack ..................................................................................... 6-4
Real Time Clock battery.................................................................... 6-4
Care and use of the battery pack ...................................................... 6-5
Safety precautions ............................................................................ 6-5
Charging the batteries ....................................................................... 6-8
Monitoring battery capacity ............................................................. 6-10
Maximizing battery operating time .................................................. 6-10
Retaining data with power off........................................................... 6-11
Extending battery life ...................................................................... 6-11
Replacing the battery pack.............................................................. 6-12
Removing the battery pack.............................................................. 6-12
Installing the battery pack ............................................................... 6-14
Starting the computer by password ................................................ 6-15
Power-up modes .............................................................................. 6-15
Windows utilities............................................................................. 6-15
Hot keys ......................................................................................... 6-15
Panel power off ................................................................................ 6-16
System Auto Off ................................................................................ 6-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
Power and Power-Up Modes
The computer’s power resources include the AC adaptor and internal batteries. This
chapter gives details on making the most effective use of these resources including
charging and changing batteries, tips for saving battery power, and power up
modes.
Power conditions
The computer’s operating capability and battery charge status are affected by the
power conditions: whether an AC adaptor is connected, whether a battery is
installed and what the charge level is for the battery.
Table 6-1 Power conditions
Power on
Power off (no operation)
universal
Battery
• Operates
• LED: Battery green
ACadaptor fully
• LED: Battery green
DCIN15V green
DCIN15V green
connected charged
Battery
partially
charged
• Operates
• Quickcharge
• Quickcharge
• LED: Battery orange
DCIN15V green
• LED: Battery orange
DCIN15V green
or no charge
No
• Operates
• Nocharge
battery
installed
• Nocharge
• LED: Battery off
DCIN15V green
• LED: Battery off
DCIN15V green
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Table 6-1 Power conditions continued
Power on
Power off (no operation)
AC
Battery
• Operates
adaptor
not
charge is
above low
• LED: Battery off
DC IN 15V off
connected battery
triggerpoint
Battery
• Operates
charge is
below low
battery
• LED: Battery
flashesorange
DC IN 15V off
triggerpoint
Battery
Computergoes
intoresumemode
shuts down
charge is
exhausted
No
• Cannotoperate
• LED: Battery off
DC IN 15V off
battery
installed
Power indicators
As shown in the above table, the Battery, DC IN 15V and Power indicators on
the system indicator alert you to the computer’s operating capability and battery
charge status.
Battery indicators
Check the Battery indicator to determine the status of the battery pack. The
following indicator lights indicate the battery status:
Flashing orange The battery charge is low. The AC adaptor must be
connected to recharge the battery.
Orange Indicates the AC adaptor is connected and charging the
battery.
Green Indicates the AC adaptor is connected and the battery is
fullycharged.
No light Under any other conditions, the indicator does not light.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery types
NOTE: If the battery becomes too hot while it is being charged, the
charge will stop and the battery indicator will go out. When the battery’s
temperature falls to a normal range, charge will resume. This occurs
whether the computer’s power is on or off.
DC IN 15V indicator
Check the DC IN 15V indicator to determine the power status with the AC adaptor
connected:
Green Indicates the AC adaptor is connected and supplying
proper power to the computer.
Flashing orange Indicates a problem with the power supply. Plug the
AC adaptor into another outlet. If it still does not operate
properly, see your dealer.
No light Under any other conditions, the indicator does not light.
Power indicator
Check the Power indicator to determine the power status:
Green Indicates power is being supplied to the computer and the
computer is turned on.
Blinkingorange Indicates power is being supplied to the computer while
the computer is in Standby mode.
No light Under any other conditions, the indicator does not light.
Battery types
The computer has two types of batteries:
❑
❑
Batterypack:12-cellbatterypackisavailable8400mAh.
RealTimeClock(RTC)battery
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Battery pack
When the AC adaptor is not connected, the computer’s main power source is a
removable lithium-ion battery pack, also referred to in this manual as the battery
pack. You can purchase additional battery packs for extended use of the computer
away from an AC power source.
Before you remove the battery pack, set the computer to Hibernation mode or save
your data and shut down the computer. Do not change the battery pack while the
AC adaptor is connected.
CAUTIONS: 1. The battery pack is a lithium-ion battery, which can
explode if not properly replaced, used, handled or
disposed of. Dispose of the battery as required by local
ordinances or regulations. Use only batteries recom-
mended by TOSHIBA as replacements.
2. Do not remove the battery pack while the computer is
in Standby mode. Data is stored in RAM, so if the
computer loses power it will be lost. When the com-
puter is powered off in Standby mode, and the univer-
sal AC adaptor is not connected, the battery pack
supplies power to maintain data and program in
memory. If the battery pack is completely discharged,
Standby mode does not function and the computer
loses all data in memory.
To ensure that the battery pack maintains its maximum capacity, operate the
computer on battery power at least once a month until the battery pack is fully
discharged. Refer to Extending battery life in this chapter for procedures. If the
computer is continuously operated on AC power through an AC adaptor for an
extended period, more than a month, the battery may fail to retain a charge. It may
not function efficiently over the expected life of the battery and the Battery
indicator may not indicate a low-battery condition.
Real Time Clock battery
TheRealTimeClock(RTC)batteryprovidespowerfortheinternalrealtimeclock
and calendar. It also maintains the system configuration.
If the RTC battery becomes completely discharged, the system loses this data and
the real time clock and calendar stop working. The following message appears when
you turn on the power:
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and use of the battery pack
**** RTC battery is low or CMOS checksum is inconsistent ****
Press [F1] key to set Date/Time.
CAUTION: The computer’s RTC battery is a nickel metal hydride battery
and should be replaced only by your dealer or by a TOSHIBA service
representative. The battery can explode if not properly replaced, used,
handled or disposed of. Dispose of the battery as required by local
ordinances or regulations.
NOTE: You can change the setting of RTC by pressing F1 key. Refer to
Chapter 9, Troubleshooting for the detail.
Care and use of the battery pack
The battery pack is a vital component of portable computing. Taking proper care of
it will help ensure longer operating time on battery power as well as a longer life for
your battery pack. Follow the instructions in this section carefully to ensure safe
operationandmaximumperformance.
Safety precautions
Mishandling of batteries can cause death, serious injury or property damage.
Carefully observe the following advisories:
Danger: Indicates an imminently hazardous situation, which could result in death
or serious injury, if you do not follow instructions.
Warning: Indicates a potentially hazardous situation, which could result in death
or serious injury, if you do not follow instructions.
Caution: Indicates a potentially hazardous situation, which if not avoided, may
result in moderate or minor injury or property damage.
Note:Providesimportantinformation.
Danger
1. Never try to dispose of the battery pack by burning or expose it to a heating
device such as a microwave oven. The battery pack could explode and cause
bodilyinjury.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
2. Never try to disassemble, repair or otherwise tamper with a battery pack. The
battery pack will overheat and ignite. Leakage of caustic alkaline solution or
other electrolytic substances will cause fire or injury, possibly resulting in
death or serious injury.
3. Never short-circuit the battery pack by contacting the terminals with a metal
object. A short-circuit can cause fire or otherwise damage the battery pack and
possibly cause injury. To avoid accidental short-circuit, always wrap the
battery pack in plastic and cover the terminals with electrical tape when storing
or disposing of the battery pack.
4. Never puncture the battery pack with a nail or other sharp object. Never strike
it with a hammer or other object. Never step on it.
5. Never try to charge the battery pack in any manner other than that described
in the user’s manual. Never connect the battery pack to a plug socket or to a
automobile’s cigarette lighter socket. It may rupture or ignite.
6. Use only the battery pack supplied with the computer or other device or an
battery pack approved by the computer or device’s manufacturer. Battery
packs have different voltages and terminal polarities. Use of an improper
battery could cause smoke, fire or rupture of the battery pack.
7. Never subject a battery pack to heat, such as storage near a heat source.
Exposure to heat can cause the battery pack to ignite, explode or leak caustic
liquid and cause death or serious injury. It could also fail or malfunction
causing data loss.
8. Never expose the battery pack to abnormal shock, vibration or pressure. The
battery pack’s internal protective device will fail, causing it to overheat,
explode, ignite or leak caustic liquids possibly resulting in death or serious
injury.
9. Never let a battery pack become wet. A wet battery pack will overheat, ignite
or rupture possibly resulting in death or serious injury.
Warning
1. Never allow caustic electrolyte fluid leaked from a battery pack to contact your
eyes, skin or clothing. If caustic electrolyte fluid should contact your eyes,
immediately wash your eyes with large amounts of running water and seek
medical attention, to help prevent eye damage. If electrolyte fluid should
contact your skin, immediately wash it under running water to prevent rash. If
it contacts your clothes, promptly remove them to prevent the fluid from
contacting your skin or eyes.
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and use of the battery pack
2. Immediately turn off the power, disconnect the universal AC adaptor and
remove the battery if any of the following events are observed in the battery
pack: offensive or unusual odor, excessive heat, discoloration or deformation.
Never use the computer again until it has been checked by a TOSHIBA
service provider. It might generate smoke or fire, or the battery pack might
rupture.
3. Make sure the battery is securely installed in the computer before attempting
to charge the battery pack. Improper installation could generate smoke or fire,
or cause the battery pack to rupture.
4. Keep the battery pack out of reach of infants and children. It can cause injury.
Caution
1. Never continue to use a battery pack after its recharging capacity has become
impaired, or after the display of a warning message indicating that the battery
pack’s power is exhausted. Continued use of an exhausted or impaired battery
pack could cause the loss of data.
2. Never dispose of battery packs with normal trash. Bring them to your
TOSHIBA dealer or to another recycling center to save resources and prevent
environmental damage. Cover the terminals with electrical tape to prevent
short-circuits, which could cause the battery pack to ignite or rupture.
3. Use only battery packs recommended by TOSHIBA as replacements.
4. Always make sure the battery pack is installed correctly and securely.
Otherwise, a battery pack could fall out and possibly cause injury.
5. Charge the battery pack only in an ambient temperature between 5 and 35
degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack
performance might deteriorate and the battery life might be shortened.
6. Be sure to monitor the remaining battery power. If the battery pack and real
time clock battery discharge completely, Standby and Suspend will not
function and data in memory will be lost. Also, the computer might register an
incorrect time and date. In this case, connect the universal AC adaptor to
recharge the batteries.
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
7. Never install or remove the battery pack without first turning off the power
and disconnecting the AC adaptor. Never remove the battery pack while the
computer is in Suspend or Standby mode. Data will be lost.
Note
1. Never remove the battery pack while the Wake-up on LAN function is
enabled. Data will be lost. Before you remove a battery pack, disable the
Wake-up on LAN function.
2. To ensure the battery pack maintains maximum capacity, operate the computer
on battery power once a week until the battery pack is fully discharged. Refer
to the section Extending battery life in this chapter for procedures. If the
computer is continuously operated on AC power for an extended period, more
than a week, the battery might fail to retain a charge. It might not function
efficiently over the expected life of the battery pack and the Battery indicator
might not indicate a low-battery condition.
3. After the battery pack is charged, avoid leaving the AC adaptor connected
and the computer turned off for more than a few hours at a time. Continuing to
charge a fully-charged battery pack can damage the battery.
Charging the batteries
When the power in the battery pack becomes low, the Battery indicator flashes
orange indicating that only a few minutes of battery power remain. If you continue
to use the computer while the Battery indicator flashes, the computer enables
Hibernation mode (so you don’t lose data) and automatically turns off.
NOTE: The computer enters Hibernate mode only if Hibernation is
enabled in two places : the Hibernate tab in Power Options and Setup
Action tab in TOSHIBA Power Saver.
You must recharge a battery pack when it becomes discharged.
Procedures
To recharge a battery pack while it is installed in the computer, connect the univer-
sal AC adaptor to the DC IN 15V socket and plug the other end into a working
outlet.
The Battery indicator glows orange when the battery is being charged.
CAUTION: Use only the computer connected to an AC power source or
the optional TOSHIBA Battery charger to charge the battery pack. Never
attempt to charge the battery pack with any other charger.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and use of the battery pack
Time
The following table shows the approximate time required to fully charge a dis-
charged battery.
Charging time (hours)
Battery type
Battery pack
RTC battery
Power on
Power off
about 3.5
8400mAh 7 to 20 or longer
8
Doesn’t charge
NOTES: 1. The charging time when the computer is on is affected by
ambient temperature, the temperature of the computer and
how you use the computer. If you make heavy use of external
devices, for example, the battery might scarcely charge at all
during operation. Refer also to the section Maximizing
battery operating time.
2. The charge time of a battery changes with the apparatus
composition and the situation of operation of a personal
computer, or the specifications of AC adaptor.
Battery charging notice
The battery may not charge right away under the following conditions:
❑
The battery is extremely hot or cold. If the battery is extremely hot, it might not
charge at all. To ensure the battery charges to its full capacity, charge the
batteryatroomtemperatureof10°to30°C(50°to88°F).
❑
The battery is nearly completely discharged. Leave the universal AC adaptor
connected for a few minutes and the battery should begin charging.
The Battery indicator may show a rapid decrease in battery operating time when
you try to charge a battery under the following conditions:
❑
❑
The battery has not been used for a long time.
The battery has completely discharged and been left in the computer for a long
time.
❑
A cool battery is installed in a warm computer.
In such case, follow the steps below.
1. Fully discharge the battery by leaving it in the computer with the power on
until the power automatically shuts off.
2. Plug in the AC adaptor.
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
3. Charge the battery until the Battery indicator glows green.
Repeat these steps two or three times until the battery recovers normal capacity.
NOTE: Leaving the AC adaptor connected will shorten battery life. At
least once a month, run the computer on battery power until the battery
is fully discharged, then recharge the battery.
Monitoring battery capacity
Remaining battery power can be monitored in Power Saver.
NOTES: 1. Wait at least 16 seconds after turning on the computer before
trying to monitor the remaining operating time. The com-
puter needs this time to check the battery’s remaining
capacity and to calculate the remaining operating time,
based on the current power consumption rate and remaining
battery capacity. The actual remaining operating time may
differ slightly from the calculated time.
2. With repeated discharges and recharges, the battery’s
capacity will gradually decrease. Therefore, an often
used, older battery will not operate for as long as a new
battery even when both are fully charged. In this case,
TOSHIBA Power Saver will indicate a 100% charge for
both the old and new battery, but the displayed estimated
time remaining will be shorter for the older battery.
Maximizing battery operating time
A battery’s usefulness depends on how long it can supply power on a single
charge.
How long the charge lasts in a battery depends on:
❑
How you configure the computer, for example, whether you enable battery-
power saving options. The computer provides a battery save mode, which can
be set in TOSHIBA Power Saver, to conserve battery power. This mode has
the following options:
• CPU Precessing speed
• Screen brightness
• System standby
• System Hibernation
6-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and use of the battery pack
• Monitor Power off
• HDDPoweroff
❑
❑
❑
How often and how long you use the hard disk and the diskette drive.
How much charge the battery contained to begin with.
How you use optional devices, such as a PC card, to which the battery
supplies power.
❑
Enabling Standby mode conserves battery power if you are frequently turning
the computer off and on.
❑
❑
❑
❑
Where you store your programs and data.
Closing the display when you are not using the keyboard saves power.
Operating time decreases at low temperatures.
The condition of the battery terminals. Make sure the battery terminals stay
clean by wiping them with a clean dry cloth before installing the battery pack.
Retaining data with power off
When you turn off your computer with fully charged batteries, the batteries retain
dataforthefollowingapproximatetimeperiods:
Battery pack 8400mAh about 6 days (Standby mode)
about 2 month (Boot mode)
RTC battery 1 month
Extending battery life
Tomaximizethelifeofyourbatterypack:
❑
At least once a month, disconnect the computer from a power source and
operate it on battery power until the battery pack fully discharges. Before doing
so, follow the steps below.
1. Turn off the computer’s power.
2. Disconnect the AC adaptor and turn on the computer’s power. If it does not
turn on go to step 4.
3. Operate the computer on battery power for five minutes. If the battery pack
has at least five minutes of operating time, continue operating until the
battery pack is fully discharged. If the Battery indicator flashes or there is
some other warning to indicate a low battery, go to step 4.
6-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
4. Connect the AC adaptor to the computer and the power cord to a power
outlet. The DC IN 15V indicator should glow green, and the Battery
indicator should glow orange to indicate that the battery pack is being
charged. If the DC IN 15V indicator does not glow, power is not being
supplied. Check the connections for the AC adaptor and power cord.
5. Charge the battery pack until the Battery indicator glows green.
❑
❑
If you have extra battery packs, rotate their use.
If you will not be using the system for an extended period, more than one
month, remove the battery pack.
❑
❑
❑
Disconnect the AC adaptor when the battery is fully charged. Overcharging
makes the battery hot and shortens life.
If you are not going to use the computer for more than eight hours, disconnect
the AC adaptor.
Store spare battery packs in a cool dry place out of direct sunlight.
Replacing the battery pack
When the battery pack reaches the end of its operating life you will need to install a
new one. The life of the battery pack is generally about 500 recharges. If the
Battery indicator flashes orange shortly after fully recharging the battery, the
battery pack needs to be replaced.
You might also replace a discharged battery pack with a charged spare when you
are operating your computer away from an AC power source. This section explains
how to remove and install the battery pack.
Removing the battery pack
To replace a discharged battery, follow the steps below.
CAUTIONS: 1. When handling battery packs, be careful not to short
circuit the terminals. Also do not drop, hit or other-
wise apply impact; do not scratch or break the casing
and do not twist or bend the battery pack.
2. Do not remove the battery pack while the computer is
in Standby mode. Data is stored in RAM, so if the
computer loses power it will be lost.
6-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the battery pack
3. In Hibernation mode, data will be lost if you remove
the battery and disconnect the universal AC adaptor
before the save is completed. Wait for the Built-in
HDD indicator to go out.
4. Do not touch the latch while holding the computer. Or
you may get injured by the dropped battery by
unintentional release of the latch.
1. Save your work.
2. Turn the computer’s power off. Make sure the Power indicator is off.
3. Remove all cables connected to the computer.
4. Turn the computer upside down.
5. Slide the battery release latch to free the battery pack for removal after
switching the battery safety lock into unlock position (direction opposite to
the battery), then slide out the battery pack.
BATTERY
SAFETY LOCK
BATTERY PACK
BATTERY
RELEASE LATCH
Figure 6-1 Releasing the battery pack
CAUTION: For environmental reasons, do not throw away a spent
battery pack. Please return spent battery packs to your TOSHIBA dealer.
6-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Installing the battery pack
To install a battery, follow the steps below.
CAUTIONS: 1. The battery pack is a lithium-ion battery, which can
explode if not properly replaced, used, handled or
disposed of. Dispose of the battery as required by local
ordinances or regulations. Use only batteries recom-
mended by TOSHIBA as replacements.
2. Do not touch the latch while holding the computer. Or
you may get injured by the dropped battery by
unintentional release of the latch.
1. Turn the computer’s power off.
2. Disconnect all cables connected to the computer.
3. Insert the battery pack.
4. Secure the battery pack lock. Switch the battery safety lock into lock
position.(direction toward the battery)
BATTERYPACK
BATTERY
RELEASE LATCH
Figure 6-2 Securing the battery pack
6-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting the computer by password
Starting the computer by password
To start up the computer with the user password, follow these steps:
1. Turn on the power as described in Chapter 3, Getting Started. The following
message appears:
Password =
NOTE: At this point, the hotkeys Fn + F1 to F5 do not work. They will
function after you enter the password.
2. Enter the password.
3. Press Enter.
NOTE: If you enter the password incorrectly three times in a row, the
computer shuts off. In this case, you must turn the computer back on to
retry password entry.
Power-up modes
The computer has the following power-up modes:
❑
Boot: Computer shuts down without saving data. Always save your work
before you turn the computer off in boot mode.
❑
❑
Hibernation: Data in memory is saved to the hard disk.
Standby: Data is maintained in the computer’s main memory.
NOTE: Refer also to the sections Turning on the power and Turning off
the power in Chapter 3, Getting Started.
Windows utilities
You can specify the setting in TOSHIBA Power Saver.
Hot keys
You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter
Hibernation. See Chapter 5, The Keyboard for details.
6-15
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Panel power on/off
You can set up your computer so that power turns off automatically when you close
the display panel. When you open the panel, power turns on in Standby or
Hibernation mode but not in boot mode.
NOTE: If the panel power off function is enabled and you use Shut down
Windows, do not close the display until the shut down function is
completed.
System Auto Off
This feature turns the system off automatically if it is not used for a set duration.
The system shuts down in Standby mode or Hibernation mode in Windows.
6-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
HW Setup and Passwords
HW Setup ........................................................................................... 7-1
Accessing HW Setup ......................................................................... 7-1
HW Setup window .............................................................................. 7-1
Supervisorpassword ....................................................................... 7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
HW Setup and Passwords
This chapter explains how to use TOSHIBA HW Setup program to configure your
computer and how to set passwords.
HW Setup
TOSHIBA HW Setup lets you configure settings for Display, CPU, Boot Priority,
Keyboard,USB,LAN,General,Password,DeviceConfigandParallel/Printer.
NOTE: If the supervisor password is set, access to the TOSHIBA HW
Setup program can be prevented when the user password is used to log
on to the computer. Some models are not equipped with Parallel/Printer
tab and/or CPU tab.
Accessing HW Setup
To run HW Setup, click start, click Control Panel, click Printers and other
Hardware and select TOSHIBA HW Setup.
HW Setup window
The HW Setup window contains the following tabs: General, Password, Device
Config, Parallel/Printer,Display,CPU,BootPriority,Keyboard,USB and LAN.
NOTE: Some models are not equipped with Parallel/Printer and/or CPU
tabs.
There are also three buttons: OK, Cancel and Apply.
OK Accepts your changes and closes the HW Setup window.
Cancel Closes the window without accepting your changes.
Apply Accepts all your changes without closing the HW Setup
window.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
General
This window displays the BIOS version and contains two buttons: Default and
About.
Default Return all HW Setup values to the factory settings.
About Display the HW Setup version.
Setup
This field displays BIOS Versionand date.
Password
User Password
This option allows you to set or reset the user password for power on.
Not Registered Change or remove the password. (Default)
Registered Set the password. A dialogue box will appear to let you set
the password.
To enter a user password:
1. Select Registered to display the following prompt:
Enter Password:
2. Enter a password of up to 10 characters. (You cannot use the following
characters: - ^ @ [ ] ; : , . / space.) The character string you enter is
displayed as a string of asterisks. For example, if you enter a password
consisting of four characters, the display is shown as:
Enter Password: ****
NOTE: If you click the OK button before entering the password, Not
registered will appear on the display.
3. Click the OK button. The following message appears, allowing you to verify
the password.
Verify Password:
4. If character strings match, the password is registered and the display changes
to:
The password was registered
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
HW Setup
If they do not match, the following message appears. You must repeat from
step 1.
Entry Error!!!
To delete a user password:
1. Select Not Registered to display the following prompt:
Enter Password:
2. Enter the currently registered password. The character string you enter is
displayed as a string of asterisks.
Enter Password: ****
NOTE: If you click the OK button before entering the password, Reg-
istered will appear on the display.
3. Click the OK button. If the character string you enter matches the registered
password, the password option is reset and the display changes to:
The password was deleted
If they do not match, the following message appears. You must repeat step 1.
Incorrect Password
NOTE: If you enter the password incorrectly three times, the screen will
display:
Sorry, access denied!!! Powering off your
machine then powering it back on again are
required to regain access.
You will not be able to access the password option in the HW Setup. In
this case you must turn the power off and back on to retry the procedure.
4. Follow the same procedures described in the earlier section, How to set the
password, to set a new user password.
Refer to the Supervisor password section later in this chapter for details on setting
the supervisor password.
Key FD
After you set a password, you can create a Key FD (diskette). If you forget the user
password, the Key FD lets you bypass the password function.
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
NOTE: It is a good idea to create more than one Key FD in case a Key
FD is damaged or lost.
To create a Key FD follow the steps below.
1. Turn off the computer’s power.
2. Connect the diskette drive to a USB port on the computer.
3. Set a diskette’s write-protect tab to the write enable position and insert the
diskette in the drive.
NOTE: All data on the diskette will be destroyed.
4. Turn on the computer’s power.
Password=will be displayed on the LCD.
5. Enter the password.
6. Press the Tab key.
Insert FD Ready (Y/N)will be displayed on the LCD.
7. Press Y.
Remove FD press keywill be displayed on the LCD.
8. Remove the diskette and press any key.
Device Config
Device Configuration
This option lets you set the device configuration.
All Devices BIOS sets all devices.
Setup by OS Operating system sets devices that it can control. (Default)
Parallel/Printer
Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel
Port Mode. Use the Windows Device Manager to make settings for the Parallel port.
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
HW Setup
Parallel Port Mode
The options in this tab are ECP and Standard Bi-directional.
ECP Sets the port type to Extended Capabilities Port (ECP). For
most printers, the port should be set to ECP. (Default)
Standard This setting should be used with some other parallel
Bi-directional devices.
Display
This tab lets you customize your computer’s display settings for either the internal
LCDscreenorforanexternalmonitor.
Power On Display
Lets you use the display to be used when the computer is booted. (This setting is
only available on Standard VGA mode and not available on Windows Desktop)
Auto-Selected Selects an external monitor if one is connected. Other-
wise, it selects the internal LCD. (Default)
LCD + Analog RGB Selects both the internal LCD and external monitor for
simultaneous display.
CPU
Celeron models are not equipped with CPU tab.
This function lets you set the CPU operating mode.
Dynamic CPU Frequency Mode
This option lets you choose from the following settings:
Dynamically CPU power consumption and clock speed
Switchable automatic switching function is enabled. When
the computer is in use, CPU operation is
automatically switched when necessary. (Default)
Always High CPU power consumption and clock speed automatic
switching function is disabled. The CPU always runs
at its fastest speed.
Always Low CPU power consumption and clock speed automatic
switching function is disabled. The CPU always runs at
low power consumption and low speed.
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
HT Technology
This tab is available only on the models with the CPU that supports Hyper-
Threading Technology (HTT). You can enable or disable the HTT feature (includ-
ing control for PM when enabling it) using this tab.
Enabled with PM* Select this option to enable the HTT feature with
PM activated.
Enabled without PM*Select this option to enable the HTT feature with
PM deactivated.
Disabled Select this option to disable the HTT feature.
* PM is Power Management’s abbreviation.
NOTE: This tab appears only on the models with the CPU that supports
the HTT feature. The options on this tab will not change to their default
settings even if you press the Default button on the General tab. Also
note that the Dynamically Switchable setting in the Dynamic CPU
Frequency Mode option is not available when the Enabled without PM
option is selected on this tab.
Boot Priority
Boot Priority Options
This option sets the priority for booting the computer. Select from the following
settings:
HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in
thefollowingorder:HDD, diskettedrive,
CD-ROMandLAN.(Default)
FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in
thefollowingorder:diskettedrive, HDD,
CD-ROMand LAN.
HDD −> CD-ROM −> LAN −> FDD The computer looks for bootable files in
thefollowingorder:HDD,CD-ROM,LAN
and diskette drive.
FDD −> CD-ROM −> LAN −> HDD The computer looks for bootable files in
thefollowingorder:diskettedrive, CD-
ROM,LANandHDD.
CD-ROM −> LAN −> HDD −> FDD The computer looks for bootable files in
thefollowingorder:CD-ROM, LAN,HDD,
diskette drive.
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
HW Setup
CD-ROM
−>
LAN
−>
FDD
−>
HDD The computer looks for bootable files in
thefollowingorder:CD-ROM,LAN,
diskette drive and HDD.
You can override the settings and manually select a boot device by pressing one of
the following keys while the computer is booting:
U
N
1
Selects the USB diskette drive.
Selects the Network.
SelectstheprimaryHDD.
Selects the PC card HDD.
SelectstheCD-ROM*.
P
C
* In this computer, CD-ROM refers to the Fixed optical media drive.
NOTES: 1. PC card HDD boot is supported only by slot 0 on the
computer. Support is guaranteed only for TOSHIBA PC
cardHDDs.
2. When you assign a PC card HDD top priority, “PC” is not
displayed. However, the PC card HDD takes the position of
HDD in the Boot Priority Options list above.
To change the boot drive, follow the steps below.
1. Hold down F12 and boot the computer.
2. Thefollowingmenuwillbedisplayedwiththefollowingicons:Built-inHDD,
CD-ROM,FDD,Network(LAN),PC(ATA)cardboot.
NOTE: A bar will appear only under the selected device.
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
3. Use the left/right cursor keys to highlight the boot device you want and press
Enter.
NOTES: 1. If a supervisor password is set, the menu above does not
appear when you use the user password to start the
computer.
2. The selection method above does not change the boot
priority settings in HW Setup.
3. If you press a key other than one of those above or if the
selected device is not installed, the system will boot according
to the current setting in HW Setup.
4. Support of PC (ATA) card boot is guaranteed only for
TOSHIBAPCcardHDDs.
5. A PC (ATA) card takes the position of HDD in the Boot
Priority Options list.
HDD Priority Options
If more than one HDD is installed in the computer, this option lets you set the
priority for HDD detection. If the first detected HDD has a boot command, the
systemwillbootfromtheHDD.
Built-in HDD −> PC Card (Default)
HDDs are searched for a boot command in the following
order: the built-in HDD, and the PC card. (Default)
PC Card −> Built-in HDD
HDDs are searched for a boot command in the following
order: the built-in HDD and the PC card.
NOTE: If a boot command is not found on the first detected HDD, the
system will not boot from the other HDD. It will search the next device in
the boot priority for a boot command.
Network Boot Protocol
This feature sets the protocol to remotely boot from the network.
[PXE] Sets PXE as the protocol. (Default)
[RPL] Sets RPL as the protocol.
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
HW Setup
NOTE: The Wake-up on LAN function consumes power even when the
system is off. Leave the universal AC adaptor connected while using this
feature.
Keyboard
Wake-up on Keyboard
When this feature is enabled and the computer is in Standby mode, you can turn on
the computer by pressing any key. It is effective only for the internal keyboard and
only when the computer is in standby mode.
Enabled Enables the Wake-up on Keyboard.
Disabled Disables the Wake-up on Keyboard. (Default)
USB
USB KB/Mouse Legacy Emulation
Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your
operating system does not support USB, you can still use a USB mouse and
keyboard by setting the USB KB/Mouse Legacy Emulationitem to
Enabled.
Enabled Enables the USB KB/Mouse Legacy Emulation. (Default)
Disabled Disables the USB KB/Mouse Legacy Emulation.
USB-FDD Legacy Emulation
Use this option to enable or disable USB-FDD Legacy Emulation.
Enabled Enables the USB-FDD Legacy Emulation. (Default)
Disabled Disables the USB-FDD Legacy Emulation.
LAN
Built-in LAN
This feature enables or disables the Built-in LAN.
Enabled EnablesBuilt-inLANfunctions.(Default)
Disabled Disables Built-in LAN functions.
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Supervisor password
Refer to the readme file of the Supervisor Password Utility for instructions on
setting the Supervisor Password.
The path to the readme file is C:\Program Files\TOSHIBA\Windows
Utilities\SVPWTool. In the SVPWTooldirectory, open the readme.htm
file.
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
Optional Devices
PCcards ............................................................................................. 8-2
Inserting a PC card ............................................................................. 8-2
RemovingaPCcard ........................................................................... 8-3
SDcards ............................................................................................. 8-4
Formatting an SD card ....................................................................... 8-4
Installing an SD card .......................................................................... 8-4
RemovinganSDcard ......................................................................... 8-5
SD card care ...................................................................................... 8-6
Memory expansion ............................................................................ 8-6
Installingmemorymodule ................................................................... 8-7
Removingmemorymodule................................................................ 8-10
Battery pack ..................................................................................... 8-11
AC adaptor ....................................................................................... 8-11
USB diskette drive ........................................................................... 8-12
External monitor .............................................................................. 8-12
i.LINK(IEEE1394) .............................................................................. 8-13
Precautions ...................................................................................... 8-13
Connecting ....................................................................................... 8-14
Disconnecting................................................................................... 8-15
Security lock .................................................................................... 8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
Optional Devices
Optional devices can expand the computer’s capabilities and its versatility. This
chapter describes connection or installation of the following devices, which are
availablefromyourTOSHIBAdealer:
Cards/memory
❑ PC cards
❑ SD cards
❑ Memoryexpansion
Power devices
❑ Battery pack
❑ Universal AC adaptor
Peripheral devices
❑ USB diskette drive
❑ Externalmonitor
❑ Parallelprinter
❑ i.LINK(IEEE1394)
Other
❑ Securitylock
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
PC cards
The computer is equipped with a PC card expansion slot that can accommodate one
5 mm Type II card. Any PC card that meets industry standards (manufactured by
TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards,
including PC card 16’s multifunction card and CardBus PC cards.
CardBus supports the new standard of 32-bit PC cards. The bus provides superior
performance for the greater demands of multimedia data transmission.
Inserting a PC card
The PC card connector is located on the left side of the computer.
Windows’ hot-install feature lets you install a PC card while the computer’s power
is on.
NOTES: 1. Do not install a PC card while the computer is in standby
or hibernation mode. Some cards might not work properly.
2. An HDD or CD-ROM connected to a 16-bit PC card, might
affect the performance of the computer’s sound system and
data transmission, including slower transmission speeds
and dialing errors.
To install a PC card, follow the steps below.
1. Insert the PC card.
2. Press gently to ensure a firm connection.
PC CARD
Figure 8-1 Inserting the PC card
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PC cards
3. Check the configuration in the HW Setup window to make sure it is appropri-
ate for your card.
After installing the card, refer to the card’s documentation and check the configura-
tion in Windows to make sure it is appropriate for your card.
Removing a PC card
To remove the PC card, follow the steps below.
1. Click the Safety Remove Hardware icon on the Task Bar.
2. ClickPCcard.
3. Press the PC card eject button to extend it.
4. Press the extended eject button to pop the card out slightly.
5. Pinch the PC card and remove it.
PC CARD
EJECT BUTTON
Figure 8-2 Removing the PC card
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
SD cards
The computer is equipped with an SD card slot that can accommodate Secure
Digital flash memory cards with various memory capacities. SD cards let you easily
transfer data from devices, such as digital cameras and Personal Digital Assistants,
that use SD card flash-memory. The cards have a high level of security and copy
protection features. The slot cannot accommodate Multi Media cards.
CAUTION: Keep foreign objects out of the SD card slot. A pin or similar
object can damage the computer’s circuitry.
NOTE: SD memory cards comply with SDMI (Secure Digital Music
Initiative), which is a technology adopted to prevent unlawful copy or
playback of digital music. For this reason, you cannot copy or playback
protected material on another computer or other device. You may not use
the reproduction of any copyrighted material except for your personal
enjoyment.
Formatting an SD card
SD memory cards are sold with format in conformity to the Standards of SD memory
card. If you format the SD card again, be sure to format it with the utility of
TOSHIBA SD memory card format, not in the format defined as the Windows
standard format.
In order to run TOSHIBA SD memory card format, click windows start button, point
to All Programs, point to TOSHIBA, point to Utilities and click SD memory card
Format.
TOSHIBA SD memory card format does not format the protected area of SD memory
card. When you format all area of the SD memory card including the protected area,
use the application that responds to the copy protection system.Installing an SD
card
To install an SD card, follow the steps below.
1. Insert the SD card.
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SD cards
2. Press gently to ensure a firm connection.
SD CARD
Figure 8-3 Inserting an SD card
CAUTION: Make sure the SD card is oriented properly before you insert
it.
Removing an SD card
To remove an SD card, follow the steps below.
1. Open the Safely Remove Hardware icon on the system tray and disable
the SD card.
2. Push in the card and release it to pop the card out slightly.
3. Grasp the card and remove it.
SD CARD INDICATOR
SD CARD
Figure 8-4 Removing an SD card
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
CAUTIONS: 1. Make sure the SD card indicator is out before you
remove the card or turn off the computer’s power. If
you remove the card or turn off the power while the
computer is accessing the card you may lose data or
damage the card.
2. Do not remove an SD card while the computer is in
Standby or Hibernation mode. The computer could
become unstable or data in the SD card could be lost.
SD card care
CAUTION: Set the write-protect switch to the lock position, if you do not
want to record data.
1. Do not write to an SD card if the battery power is low. Low power could affect
writingaccuracy.
2. Do not remove an SD card while read/write is in progress.
3. The SD card is designed so that it can be inserted only one way. Do not try to
force the card into the slot.
4. Do not leave an SD card partially inserted in the slot. Press the SD card until
you hear it click into place.
5. Do not twist or bend SD cards.
6. Do not expose SD cards to liquids or store in humid areas or lay media close to
containers of liquid.
7. After using an SD card, return it to its case.
8. Do not touch the metal part or expose it to liquids or let it get dirty.
NOTE:Please use an SDIO card*1 which is supported in the SD slot of
this machine.If you use an SDIO card which is not supported in the SD
slot of this machine, the system may become unstable.
*1: As of September, 2003, An SDIO card which is supported in the SD
slot of this machine is not on sale.
Memory expansion
This computer is equipped with two memory module sockets beneath the keyboard.
You can increase the amount of RAM by installing an additional memory or
replacing default memories with additional memories. This section describes how to
installandremoveamemorymodule.
8-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory expansion
CAUTIONS: 1. Refer to General Precautions for the attention when
keyboard brace is removed.
2. Use only memory modules approved by TOSHIBA.
3. Do not try to install or remove a memory module under
the following conditions. You can damage the computer
and the module. Also, data will be lost.
a. The computer is turned on.
b. The computer was shut down using the Stand by
mode or Hibernation mode.
NOTES: 1. Place a mat beneath the computer to prevent making a
scratch on the lid when replacing the memory module.
Avoid the mat that generates static electricity.
2. Use a point size 0 Phillips screwdriver to remove and
fasten screws. Use of an incorrect screwdriver can
damage the screw heads.
Installing memory module
To install a memory module, make sure the computer is in boot mode then:
1. Turn the computer off in boot mode. Refer to the Turning off the power
section in Chapter 3, Getting Started.
2. Remove all cables connected to the computer.
3. Turn the computer upside down and remove the battery pack (refer to Chapter
6, Power and Power-Up Modes.)
4. Slide the display latch on the front of the computer to the right and open the
display panel.
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
5. Insert a thin object under the rim of the keyboard brace and lift out the brace.
Figure 8-5 Removing the keybord brace
6. Remove two screws securing the keyboard and one screw securing the metal
brace. Lift off the metal brace.
NOTE: Use a point size 0 Phillips screwdriver.
7. Lift up the back of the keyboard, rotate it toward you and lay in face down on
the palm rest.
CAUTIONS: 1. When you move the keyboard forward, do not touch the
keys. Doing so could cause misalignment. Hold the
keyboard by the sides and lay it gently on the palm rest.
2. The keyboard is connected to the computer by a ribbon
cable. Be careful not to apply tension to this cable when
you lift up the keyboard. Do not try to disconnect this
cable.
Figure 8-6 Removing three screws and one metal brace,
and rotate the keyboard
8-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory expansion
8. Lift into the left the insulation sheet covering the memory module and secure
the sheet with tape to keep it out of your way.
CAUTION: Do not touch the connectors on the memory module or on the
computer. Debris on the connectors may cause memory access problems.
NOTE: The slot A is reserved for main memory. Use the slot B for
expanded memory. If only one card is installed, use the slot A.
SLOT
A
SLOT
B
Figure 8-7 Lifting into the left the insulation sheet.
9. Insert a new module in the socket and push it down so it lies flat and is
secured by two latches on either side.
Figure 8-8 Installing the memory module.
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
10. Seat the insulation sheet to cover the module.
NOTE: Be sure to check that the insulation sheet is returned to the
original position to cover the memory module.
11. Insert tabs on the front of the keyboard into corresponding notches on the
computer and seat the keyboard.
CAUTION: When seating the keyboard, be sure to fit the flexible printed
circuit board under the palm rest if the flat cable was pulled out while
you were removing the keyboard.
12. Two screws secure the keyboard and one screw secures the metal brace.
CAUTION: Be sure to use all two screws removed in step 6. Make sure
no screw was dropped into the computer. Make sure all foreign matter,
such as the tape applied in step 9 is removed.
13. Seat the keyboard brace and press to secure latches.
14. Install the battery pack. Refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, for details.
15. Turn the power on and make sure the added memory is recognized. Open
System Properties in the Control Panel and click the General tab.
Removing memory module
To remove the memory module, make sure the computer is in boot mode then:
1. Turn the computer off and remove all cables connected to the computer.
2. Turn the computer upside down and remove the battery pack (refer to Chapter
6, Power and Power-Up Modes.)
3. Slide the display latch on the front of the computer to the right and open the
display panel.
4. Follow steps 5 through 8 in Installing memory module to access the memory
module.
5. Push the latches to the outside to release the module. A spring will force one
end of the module up.
6. Grasp the sides of the module and pull it out, then replace the insulator.
8-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery pack
CAUTIONS: 1. If you use the computer for a long time, the memory
modules and the circuits locating close to the memory
modules will become hot. In this case, let them cool to
room temperature before you replace them. Or you will
get burnt if you touch any of them.
2. Do not touch the connectors on the memory module or
on the computer. Debris on the connectors may cause
memory access problems.
LATCHES
Figure 8-9 Removing the memory module
7. Rotate the keyboard back into place and secure the keyboard brace as
described in the previous section.
8. Turn the computer upside down and replace the battery pack.
Battery pack
You can increase the portability of the computer with additional battery packs. If
you’re away from an AC power source and your battery runs low, you can replace it
with a freshly charged battery. Refer to Chapter 6, Power and Power-Up Modes.
Universal AC adaptor
If you frequently transport the computer between different sites such as your home
and office, purchasing an AC adaptor for each location will reduce the weight and
bulk of your carrying load.
8-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
USB diskette drive
The 3 1/2" external diskette drive module can be connected to the USB port. For
details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4,
Operating Basics.
External monitor
An external analog monitor can be connected to the external monitor port on the
computer. The computer supports VGA and Super VGA video modes. To connect a
monitor, follow the steps below.
1. Turn the computer off.
2. Connect the monitor to the external monitor port.
3. Turn the monitor’s power on.
4. Turn the computer on.
When you turn on the power, the Windows Bootup screen (Windows Logo)
appears on the display device that is set as the power on Displayin HW
Setup (Refer to Chapter 7, HW Setup and Passwords for more information).
However, the Windows Desktop appears on a display device that you used last
time to shut down your PC, if the display device exists when you turn on the power.
To change the display settings, press Fn + F5. If you disconnect the monitor
before you turn the computer off, be sure to press Fn + F5 to switch to the internal
display. Refer to Chapter 5, The Keyboard, for details on using hot keys to change
the display setting.
Parallel printer
You can connect any standard Centronics-compatible parallel printer to your
computer. All you need is an IBM PC™ parallel printer cable. Your dealer can
supply one or you can purchase one at most computer stores.
The cable’s connectors are designed so that it is impossible for you to connect
them incorrectly. To connect a printer, follow these steps:
1. Turn off the computer.
2. Insert one end of the cable into the computer’s parallel port.
3. Tighten the screws that fasten the cable connector to the computer’s parallel
port.
8-12
Download from Www.Somanuals.com. All Manuals Search And Download.
i.LINK (IEEE1394)
4. Insert the other end of the cable into the printer’s parallel connector.
5. Fasten the connector to the printer with the clips on the parallel port.
6. Turn on the printer.
7. Turn on the computer.
8. Start the HW Setup program. Refer to Chapter 7, HW Setup and Passwords.
9. Select the Parallel/Printertab from the TOSHIBA HW Setup
window.
10. Set the Parallel Port Modeand press OK.
11. Choose Rebootfor the change to take effect.
12. Select the printer in Windows Add Print Wizard. To access the Add Print
Wizardutility, click Start, point to Settings, click Printers and double
click the Add Printer icon.
i.LINK (IEEE1394)
i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible
devices such as
❑ Digitalvideocameras
❑ Hard disk drives
❑ MO drives
❑ CD-RWdrives
NOTE: i.LINK uses a four-pin connector, which does not carry electric
current. External devices will need their own power supply.
Precautions
❑ Make a back-up of your data before transferring it to the computer. There is a
possibility that the original data will be damaged. There is a particular risk that
some frames will be deleted in the case of digital video transfer. TOSHIBA
assumes no liability for such loss of data.
❑ Do not transfer data in areas where static electricity is easily generated or in
areas subjected to electronic noise. Data can be destroyed.
❑ If you are transferring data through an IEEE1394 hub, do not connect or
disconnect other devices from the hub during data transfer. There is a likeli-
hood that data will be damaged. Connect all devices to the hub before you turn
on the computer’s power.
8-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
❑ You may not use any copyrighted video or music data copied from a video
camera except for your personal enjoyment.
❑ If you connect/disconnect an i.LINK device to/from another i.LINK device that
is currently exchanging data with the computer, data frames might be dropped.
❑ Make sure data transfer has ended or turn off the computer, before you:
• Connect/disconnect an i.LINK device to/from the computer.
• Connect/disconnect an i.LINK device to/from another i.LINK device that is
connected to the computer.
Connecting
1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394)
cable into the computer.
Figure 8-10 Connecting the i.LINK cable
2. Plug the other end of the cable into the device.
Note the following when you use i.LINK:
❑ You may need to install drivers for your i.LINK devices.
❑ Notalli.LINKdeviceshavebeentested, therefore, compatibilitywithalli.LINK
devices cannot be guaranteed.
❑ Use S100, S200 or S400 cables no longer than three meters.
❑ Some devices might not support standby or automatic off functions.
❑ Do not connect or disconnect an i.LINK device while it is using an application
or when the computer is automatically shutting it down to save power. Data
might be destroyed.
8-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Security lock
Disconnecting
1. Open the Safely Remove Hardware icon on the Task Bar.
2. Point toi.LINK(IEEE1394)deviceandclick.
3. Disconnect the cable from the computer then from the i.LINK device.
NOTE: Refer also to the documentation that came with your i.LINK device.
Security lock
A security lock enables you to anchor your computer to a desk or other heavy
object to help prevent unauthorized removal of the computer.
Attach one end of a cable to the desk and the other end to the security lock slot on
the back side of the computer.
CAUTION: The Security Lock Slot is between Cooling Vent. After using
this computer, the Security Lock Slot is hot because of the exhaust heat
from the Cooling Vent. There is a possibility of getting burnt when the
Security Lock Slot is touched at this time. Therefore, be careful enough
work after it is confirmed that heat is cold enough after the computer is
used.
Figure 8-11 Security lock
8-15
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
8-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9
Troubleshooting
Problemsolvingprocess................................................................... 9-1
Preliminary checklist .......................................................................... 9-1
Analyzing the problem ........................................................................ 9-2
Hardware and system checklist........................................................ 9-3
System start-up.................................................................................. 9-3
Self test.............................................................................................. 9-4
Power ................................................................................................. 9-4
Battery ............................................................................................... 9-6
Password ........................................................................................... 9-7
Keyboard ............................................................................................ 9-7
LCDpanel ........................................................................................ 9-10
Harddiskdrive .................................................................................. 9-11
DVD-ROMdrive ................................................................................ 9-12
CD-RW/DVD-ROMdrive ................................................................... 9-13
DVD-R/-RWdrive .............................................................................. 9-14
DVDMultidrive................................................................................. 9-16
DVD±RWdrive(DVDDualdrive) ....................................................... 9-18
Diskettedrive.................................................................................... 9-19
PC card ............................................................................................ 9-20
SD card ............................................................................................ 9-20
Pointingdevice ................................................................................. 9-21
USB ................................................................................................. 9-23
Memoryexpansion ........................................................................... 9-24
Sound System ................................................................................. 9-24
Monitor ............................................................................................. 9-25
Modem ............................................................................................. 9-25
Standby/Hibernation ......................................................................... 9-27
LAN .................................................................................................. 9-27
Wireless LAN ................................................................................... 9-27
i.LINK(IEEE1394) ............................................................................ 9-28
Real Time Clock ............................................................................... 9-28
Printer .............................................................................................. 9-29
TOSHIBAsupport ............................................................................. 9-30
Before you call ................................................................................. 9-30
Where to write .................................................................................. 9-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 9
Troubleshooting
TOSHIBA designed the computer for durability. However, should problems occur,
following the procedures in this chapter can help to determine the cause.
All readers should become familiar with this chapter. Knowing what might go wrong
can help prevent problems from occurring.
Problem solving process
Resolving problems will be much easier if you observe the following guidelines:
❑
Stop immediately when you recognize a problem exists. Further action may
result in data loss or damage. You may destroy valuable problem-related
information that can help solve the problem.
❑
Observe what is happening. Write down what the system is doing and what
actions you performed immediately before the problem occurred. If you have a
printer attached, print a copy of the screen using PrtSc SysReq.
The questions and procedures offered in this chapter are meant as a guide, they are
not definitive problem solving techniques. Many problems can be solved simply,
but a few may require help from your dealer. If you find you need to consult your
dealer or others, be prepared to describe the problem in as much detail as possible.
Preliminary checklist
Consider the simplest solution first. The items in this checklist are easy to fix and yet
can cause what appears to be a serious problem.
❑
Make sure you turn on all peripheral devices before you turn on the computer.
This includes your printer and any other external device you are using.
❑
Before you attach an external device, turn the computer off. When you turn the
computer back on it recognizes the new device.
❑
❑
Make sure all options are set properly in the setup program.
Check all cables. Are they correctly and firmly attached? Loose cables can
cause signal errors.
❑
Inspect all connecting cables for loose wires and all connectors for loose pins.
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
❑
Check that your diskette or CD/DVD-ROM is correctly inserted and that the
diskette’s write protect tab is correctly set.
Make notes of your observations and keep them in a permanent error log. This will
help you describe your problems to your dealer. If a problem recurs, the log will help
you identify the problem faster.
Analyzing the problem
Sometimes the system gives clues that can help you identify why it is malfunction-
ing. Keep the following questions in mind:
❑
Which part of the system is not operating properly: keyboard, diskette drives,
hard disk drive, optical media drive, display. Each device produces different
symptoms.
❑
❑
Is the operating system configuration set properly? Check the configuration
options.
What appears on the display screen? Does it display any messages or random
characters? Print a copy of the screen if you have a printer attached. Look up
the messages in the software and operating system documentation. Check that
all connecting cables are correctly and firmly attached. Loose cables can cause
erroneous or intermittent signals.
❑
❑
Do any indicators light? Which ones? What color are they? Do they stay on or
blink? Write down what you see.
Do you hear any beeps? How many? Are they long or short? Are they high
pitched or low? Is the computer making any unusual noises? Write down what
you hear.
Record your observations so you can describe them to your dealer.
Software The problems may be caused by your software or disk
(disc). If you cannot load a software package, the media
may be damaged or the program might be corrupted. Try
loading another copy of the software.
If an error message appears while you are using a software
package, check the software documentation. These
documents usually include a problem solving section or a
summary of error messages.
Next, check any error messages in the OS documentation.
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Hardware If you cannot find a software problem, check your
hardware. First run through the items in the preliminary
checklist above. If you still cannot correct the problem, try
to identify the source. The next section provides checklists
for individual components and peripherals.
Hardware and system checklist
This section discusses problems caused by your computer’s hardware or attached
peripherals. Basic problems may occur in the following areas:
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
System start-up
Self test
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
❑
PCcard
SDcard
Power
Pointing device
USB
Battery
Password
Memoryexpansion
Sound System
Monitor
Keyboard
LCDpanel
Hard disk drive
DVD-ROMdrive
CD-RW/DVD-ROMdrive
DVD-R/-RWdrive
DVDMultidrive
DVD±RWdrive
(DVDDualdrive)
Diskette drive
Modem
Standby/Hibernation
LAN
WirelessLAN
i.LINK (IEEE1394)
RealTimeClock
Printer
❑
System start-up
When the computer does not start properly, check the following items:
❑
❑
❑
SelfTest
Power Sources
Power-on Password
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Self test
When the computer starts up, the self test will be run automatically, and the
followingwillbedisplayed:
In Touch with Tomorrow
TOSHIBA
This message remains on the screen for a few seconds.
If the self test is successful, the computer tries to load the operating system,
depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
If any of the following conditions are present, the self test failed:
❑
❑
❑
The computer stops and does not proceed to display information or messages
except the TOSHIBA logo.
Random characters appear on the screen, and the system does not function
normally.
The screen displays an error message.
Turn off the computer and check all cable connections as well as PC card and
memory module connections. If the test fails again, contact your dealer.
Power
When the computer is not plugged into an AC outlet, the battery pack is the primary
power source. However, your computer has a number of other power resources,
including intelligent power supply, Real Time Clock battery. These resources are
interrelated and any one could affect apparent power problems. This section
provides check lists for AC power and the battery. If you cannot resolve a problem
after following them, the cause could lie with another power resource. In such case,
contact your dealer.
9-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Overheating power down
If the computer’s internal temperature becomes too high, the computer will automati-
cally enter Hibernation or Resume mode and shut down.
Problem
Procedure
Computershutsdown Leave the computer off until the DC IN 15V
and DC IN 15V
indicator blinks
orange
indicator stops blinking.
NOTE: It is recommended to leave the computer
off until the its interior reaches room temperature
even though the DC IN 15V indicator stops
blinking.
If the computer has reached room temperature
and still does not start, or if it starts but shuts
down quickly, contact your dealer.
Computershutsdown Indicates a problem with the heat dispersal
and its DC IN 15V
indicator is flashing
green
system. Please contact your dealer.
AC power
If you have trouble turning on the computer with the AC adaptor connected, check
the DC IN 15V indicator. Refer to Chapter 6, Power and Power-Up Modes for more
information.
Problem
Procedure
ACadaptordoesn’t
powerthecomputer
(DC IN 15V indicator
doesnotglowgreen)
Check the connections. Make sure the cord is
firmly connected to the computer and a power
outlet.
9-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Check the condition of the cord and terminals. If
the cord is frayed or damaged, replace it. If the
terminals are soiled, wipe them with cotton or a
clean cloth.
If the AC adaptor still does not power the com-
puter, contact your dealer.
Battery
If you suspect a problem with the battery, check the DC IN 15V indicator as well as
the Battery indicator. For information on indicator and battery operation see
Chapter 6, Power and Power-Up Modes.
Problem
Procedure
Battery doesn’t
powerthecomputer
The battery may be discharged. Connect the
AC adaptor to charge the battery.
Battery doesn’t
chargewhenthe
AC adaptor is
If the battery is completely discharged, it will
not begin charging at once. Wait a few minutes.
attached(Battery
indicator does not
gloworange.)
If the battery still does not charge, make sure the
outlet is supplying power. Plug in an appliance
and see if it works. If it doesn’t, try another power
source.
Check whether the battery is hot or cold. If the
battery is too hot or too cold, it will not charge
properly. Let it reach room temperature.
Unplug the AC adaptor and remove the battery to
make sure the terminals are clean. If necessary
wipe them with a soft dry cloth dipped in alcohol.
Connect the AC adaptor and replace the battery.
Make sure the battery is securely seated.
9-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Check the Battery indicator. If it does not glow,
let the computer charge the battery for at least 20
minutes. If the Battery indicator glows after 20
minutes, let the battery continue to charge at
least another 20 minutes before turning on the
computer.
If the indicator still does not glow, the battery
may be at the end of its operating life. Replace it.
If you do not think the battery is at the end of its
operating life, see your dealer.
Battery doesn’t
powerthecomputer
as long as expected
If you frequently recharge a partially charged
battery, the battery might not charge to its full
potential. Fully discharge the battery, then try to
charge it again.
Check the power consumption settings in
TOSHIBA Power Saver utility. Consider using a
powersavingmode.
Password
Problem
Procedure
Cannotenter
Contactyourdealer.
orforgotpassword
NOTE: For information on setting a password,
refer to Chapter 7, HW Setup and Passwords.
Keyboard
Keyboard problems can be caused by your setup configuration. For more informa-
tion refer to Chapter 5, The Keyboard and Chapter7, HW Setup and Passwords.
9-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Problem
Procedure
Some letter keys
producenumbers
Check that the numeric keypad overlay is not
selected. Press Fn + F10 and try typing again.
Output to screen
isgarbled
Make sure the software you are using is not
remappingthekeyboard.Remappinginvolves
reassigning the meaning of each key. See your
software’sdocumentation.
If you are still unable to use the keyboard,
consult your dealer.
Key-top
comesoff
Follow the figures below to attach Enter, Back
Space, Shift or Space key when they come off.
For the other keys, press the key-top until you
hear a click after replacing it to the right position.
•The way to replace the key-top
Press the key-top until you hear a click after
removing a metal spring from the key-top,
hooking it to projecting parts and aligning the
center of the key-top.
Enter, Back Space, Shift and Space key
PROJECTING PARTS
9-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
PRESS FROM THE UPSIDE
PROJECTING PART
SPRING
PROJECTING PART
• Follow the steps below when a plastic spring is
out of place together with a key- top.
1. Remove the plastic spring from the key-top.
9-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
2. Attach the plastic spring to the keyboard with
its flat face downward after confirming the direction.
FLAT FACE DOWNWARD
3. Press from the upside until you hear a click
after replacing the key-top to the right position.
LCD panel
Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7,
HW Setup and Passwords for more information.
Problem
Procedure
No display
Press hot keys Fn + F5 to change the display
priority, to make sure it is not set for an external
monitor.
Markingsappearon
theLCD.
They might have come from contact with the
keyboard, Touch Pad. Try wiping the LCD gently
with a clean dry cloth. If markings remain, use
LCD cleaner. Be sure to let the LCD dry before
closing it.
9-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Problemsabove
remainunresolved
orotherproblems
occur
Refer to your software’s documentation to
determine if the software is causing the
difficulty.
Contact your dealer if the problems continue.
Hard disk drive
Problem
Procedure
Computerdoesnot
boot from hard disk
drive
Check if a diskette is in the diskette drive or a
CD-ROM is in the optical media drive. Remove
any diskette and/or CD-ROM and check Boot
priority. Refer to the Boot Priority section in
Chapter 7, HW Setup and Passwords.
There may be a problem with your operating
system files. Refer to your OS documentation.
Slowperformance
Your files may be fragmented. Run SCANDISK
and defragmenter to check the condition of your
files and disk. Refer to your OS documentation
or online HELP for information on running
SCANDISKandthedefragmenter.
As a last resort, reformat the hard disk. Then,
reload the operating system and other files.
If problems persist, contact your dealer.
9-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
DVD-ROM drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
Make sure the drive’s drawer is securely
a CD/DVD in the drive closed. Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facingup.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
SomeCD/DVDs
run correctly, but
others do not
Thesoftwareorhardwareconfigurationmay
be causing a problem. Make sure the
hardwareconfigurationmatchesyoursoftware’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drivesupports:
DVD-ROM: DVD-ROM,DVD-Video
CD-ROM:
CD-DA, CD-Text, PhotoCD(single/
multi-session),CD-ROMMode1,
Mode 2, CD-ROM XA Mode 2
(Form1,Form2),EnhancedCD(CD-
EXTRA),CD-G(AudioCDonly),
AddressingMethod2
9-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Check the region code on the DVD. It must
match that on the DVD-ROM drive. Region codes
are listed in the Optical media section in Chapter
2,TheGrandTour.
If problems persist, contact your dealer.
CD-RW/DVD-ROM drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
Make sure the drive’s drawer is securely
a CD/DVD in the drive closed. Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facingup.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. Refer to Media care section in Chapter 4
for details on cleaning.
SomeCD/DVDs
run correctly, but
others do not
Thesoftwareorhardwareconfigurationmay
be causing a problem. Make sure the
hardwareconfigurationmatchesyoursoftware’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drivesupports:
DVD-ROM: DVD-ROM,DVD-Video
9-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
CD-ROM:
CD-DA,CD-Text,PhotoCD™
(single/multi-session),CD-ROM
Mode 1, Mode 2, CD-ROM XA Mode
2(Form1, Form2), EnhancedCD
(CD-EXTRA),CD-G(AudioCDonly),
AddressingMethod2
Recordable: CD-R,CD-RW
CD
Check the region code on the DVD. It must
matchthatontheCD-RW/DVD-ROMdrive.
Region codes are listed in the Optical media
section in Chapter 2, The Grand Tour.
Cannot write correctly If you have trouble writing, make sure you are
observingthefollowingprecautions:
• Use only media recommended by TOSHIBA.
• Do not use the mouse or keyboard during
writing.
• Use only the software supplied with the
computerforrecording.
• Do not run or start other software during
writing.
• Do not jar the computer during writing.
• Do not connect/ disconnect external devices
orinstall/removeinternalcardsduringwriting.
If problems persist, contact your dealer.
DVD-R/-RW drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
Make sure the drive’s drawer is securely
a CD/DVD in the drive closed. Press gently until it clicks into place.
9-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facingup.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
SomeCD/DVDs
run correctly, but
others do not
Thesoftwareorhardwareconfigurationmay
be causing a problem. Make sure the
hardwareconfigurationmatchesyoursoftware’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drivesupports:
DVD-ROM: DVD-ROM,DVD-Video
CD-ROM:
CD-DA, CD-Text, PhotoCD(single/
multi-session),CD-ROMMode1,
Mode 2, CD-ROM XA Mode 2
(Form1,Form2),EnhancedCD(CD-
EXTRA),CD-G(AudioCDonly),
AddressingMethod2
Check the region code on the DVD. It must
match that on the DVD-R/-RW drive. Region
codes are listed in the Optical media section in
Chapter2,TheGrandTour.
Cannot write correctly If you have trouble writing, make sure you are
observingthefollowingprecautions:
• Use only media recommended by TOSHIBA.
9-15
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
• Do not use the mouse or keyboard during
writing.
• Use only the software supplied with the
computerforrecording.
• Do not run or start other software during
writing.
• Do not jar the computer during writing.
• Do not connect/ disconnect external devices or
install/removeinternalcardsduringwriting.
If problems persist, contact your dealer.
DVD Multi drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
Make sure the drive’s drawer is securely
a CD/DVD in the drive closed. Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facingup.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
9-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
SomeCD/DVDs
run correctly, but
others do not
Thesoftwareorhardwareconfigurationmay
be causing a problem. Make sure the
hardwareconfigurationmatchesyoursoftware’s
needs. Check the CD/DVD’s documentation.
Check the type of CD/DVD you are using. The
drivesupports:
DVD-ROM: DVD-ROM,DVD-Video
Recordable: DVD-R,DVD-RW,DVD-RAM
DVD
CD-ROM:
CD-DA, CD-Text, PhotoCD(single/
multi-session),CD-ROMMode1,
Mode 2, CD-ROM XA Mode 2
(Form1,Form2),EnhancedCD(CD-
EXTRA),CD-G(AudioCDonly),
AddressingMethod2
Recordable: CD-R,CD-RW
CD
Check the region code on the DVD. It must match
that on the DVD Multi drive. Region codes are
listed in the Optical media section in Chapter 2,
TheGrandTour.
Cannot write correctly If you have trouble writing, make sure you are
observingthefollowingprecautions:
• Use only media recommended by TOSHIBA.
• Do not use the mouse or keyboard during
writing.
• Use only the software supplied with the
computerforrecording.
• Do not run or start other software during writing.
• Do not jar the computer during writing.
• Do not connect/ disconnect external devices or
install/removeinternalcardsduringwriting.
If problems persist, contact your dealer.
9-17
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
DVD±RW drive (DVD Dual drive)
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
You cannot access
Make sure the drive's drawer is securely closed.
a CD/DVD in the drive Press gently until it clicks into place.
Open the drawer and make sure the CD/DVD is
properly seated. It should lie flat with the label
facingup.
A foreign object in the drawer could block laser
light from reading the CD/DVD. Make sure there
is no obstruction. Remove any foreign object.
Check whether the CD/DVD is dirty. If it is, wipe
it with a clean cloth dipped in water or a neutral
cleaner. See the Media care section in Chapter 4
for details on cleaning.
Some CD run
correctly, but
others do not
Thesoftwareorhardwareconfigurationmaybe
causing a problem. Make sure the hardware
configurationmatchesyoursoftware'sneeds.
ChecktheCD/DVD'sdocumentation.
Check the type of CD/DVD you are using. The
drivesupports:
DVD-ROM: DVD-ROM,DVD-Video,DVD-R,
DVD-RW,DVD+R,DVD+RW
CD-ROM:
CD-DA, CD-Text, PhotoCD(single/
multi-session),CD-ROMMode1,
Mode 2, CD-ROM XA Mode 2
(Form1,Form2),EnhancedCD(CD-
EXTRA),CD-G(AudioCDonly),
AddressingMethod2
9-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Check the region code on the DVD.
It must match that on the DVD±RW
drive. Region codes are listed in the
Optical media section in Chapter 2,
TheGrandTour.
Cannot write correctly If you have trouble writing, make sure you are
observingthefollowingprecautions:
•
•
Use only media recommended by TOSHIBA.
Do not use the mouse or keyboard during
writing.
•
Use only the software supplied with the
computer forrecording.
•
•
•
Do not run or start other software during writing.
Do not jar the computer during writing.
Do not connect/ disconnect external devices or
install/removeinternalcardsduringwriting.
If problems persist, contact your dealer.
Diskette drive
For more information, refer to Chapter 4, Operating Basics.
Problem
Procedure
Drivedoesnot
operate
There may be a faulty cable connection. Check
the connection to the computer and to the drive.
Someprogramsrun
correctly but others
do not
Thesoftwareorhardwareconfigurationmaybe
causing a problem. Make sure the hardware
configurationmatchesyoursoftwareneeds.
You cannot access
the external 3 1/2"
diskettedrive
Try another diskette. If you can access the
diskette, the original diskette (not the drive) is
probablycausingtheproblem.
If problems persist, contact your dealer.
9-19
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
PC card
Refer also to Chapter 8, Optional Devices.
Problem
Procedure
PC card
erroroccurs
Reseat the PC card to make sure it is
firmlyconnected.
Make sure the connection between the external
device and the card is firm.
Check the card’s documentation.
If problems persist, contact your dealer.
SD card
Refer also to Chapter 8, Optional Devices.
Problem
Procedure
SD card
erroroccurs
Reseat the SD card to make sure it is firmly
connected.
Check the card’s documentation.
You cannot write
to an SD card
Make sure the card is not write protected.
You cannot read
a file
Make sure the target file is on the SD
Card inserted in the slot.
If problems persist, contact your dealer.
9-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Pointing device
If you are using a USB mouse, also refer to the USB section in this chapter and to
your mouse documentation.
Touch Pad
Problem
Procedure
On-screenpointer
does not respond to
Padoperation
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to standby
its normal shape and try again to move it.
Double-tapping
does not work
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Buttons tab.
3. Set the double-click speed as instructed and
click OK.
Themousepointer
moves too fast or
too slow
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
If problems persist, contact your dealer.
Adjust the touch Sensitivity.
When the reaction of
9-21
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Touch pad is sensitive 1. Open the Control Panel.
orblunt.
2. Click the Printers icon and then the Other
Hardware icon.
3. Click the Mouse icon.
4. Click the Device Setting tab.
5. Click the Setting button.
6. The Properties for Synaptics Touchpad on PS/2
port screen appears. Double-click Sensitivity in
the Select an item section on the left side of
the screen.
7. PalmCheck and Touch Sensitivity are dis
played. Click Touch Sensitivity.
8. Move the slide bar for Touch Sensitivity to
make an adjustment. Click the OK button.
9. Click the OK button on the Device Setting tab.
USB mouse
Problem
Procedure
On-screenpointer
does not respond to
mouseoperation
The system might be busy. If the pointer is
shaped as an hourglass, wait for it to resume
its normal shape and try again to move it.
Make sure the mouse is properly connected to
the USB port.
Double-clicking
does not work
Try changing the double-click speed setting in
the mouse control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
9-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
2. Click the Buttons tab.
3. Set the double-click speed as instructed and
click OK.
Themousepointer
moves too fast or
too slow
Try changing the speed setting in the mouse
control utility.
1. Open the Control Panel, select the Mouse
icon and press Enter.
2. Click the Pointer Options tab.
3. Set the speed as instructed and click OK.
Themousepointer
moveserratically
The mouse might be dirty. Refer to your mouse
documentations for instructions on cleaning.
If problems persist, contact your dealer.
USB
Refer also to your USB device’s documentation.
Problem
Procedure
USBdevicedoes
not work
Check for a firm cable connection between the
USB ports on the computer and the USB device.
Make sure the USB device drivers are properly
installed. Refer to your Windows XP documenta-
tion for information on checking the drivers.
If you are using an operating system that does
not support USB, you can still use a USB mouse
and/or USB keyboard. If these devices do not
work, make sure the USB KB/Mouse Legacy
Emulation item in HW Setup is set to Enabled.
If problems persist, contact your dealer.
9-23
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Memory expansion
Refer also to Chapter 8, Optional Devices, for information on installing memory
modules.
Problem
Procedure
Beep sounds.
Make sure the memory module installed in the
expansion slot is compatible with the computer.
If an incompatible module has been installed,
follow the steps below.
(If slot A, two beeps.
If slot B, three beeps.
If both, two and three
beeps. )
1. TurnoffthePower.
2. Disconnect the AC adaptor and all more,
peripheraldevices.
3. Removethebattery.
4. Removethememorymodule.
5. Replace the battery and/or connect the AC
adaptor.
6. Turnonthepower.
If problems persist, contact your dealer.
Sound System
Refer also to documentation for your audio devices.
Problem
Procedure
No sound is heard
Adjust the volume control dial.
Check the software volume settings.
Make sure the headphone connection is secure.
If problems persist, contact your dealer.
9-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Monitor
Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.
Problem
Procedure
Monitor does not
turnon
Make sure that the external monitor’s power
switch is on. Confirm that the external monitor’s
power cable is plugged into a working power
outlet.
No display
Try adjusting the contrast and brightness controls
on the external monitor.
Press hot keys Fn + F5 to change the display
priority and make sure it is not set for the internal
display.
Displayerroroccurs
Check that the cable connecting the external
monitor to the computer is attached firmly.
If problems persist, contact your dealer.
Modem
Refer to Appendix C and D.
Problem
Procedure
Communication
softwarecan’t
initialize modem
Make sure the computer’s internal modem
settings are correct. Refer to Phone and Modem
Properties in the Control Panel.
You can hear a dial
tone but can’t make
a call
If the call is going through a PBX machine, make
sure the communication application’s tone dial
detection feature is disabled.
9-25
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
You can also use the ATX command. Refer to
Appendix C, AT Commands.
You place a call,
but a connection
can’t be made
Make sure the settings are correct in your
communicationsapplication.
After making a call
you can’t hear a ring
Make sure the tone or pulse selection in your
communications application is set correctly.
You can also use the ATD command. Refer to
Appendix C, AT Commands.
Communicationis
cut off unexpectedly
The computer will automatically cut off
communication when connection with the carrier
is not successful for a set time interval. Try
lengtheningthistimeinterval.
A CONNECTdisplay
is quickly replaced by
NO CARRIER
Check the error control setting in your
communications application.
You can also use the AT\N command. Refer to
Appendix C, AT Commands.
Characterdisplay
becomesgarbled
duringa
In data transmission, make sure the parity bit
and stop bit settings correspond with those
of the remote computer.
communication
Check the flow control and communication
protocol.
Youcannotreceive
an incoming call
Check the rings before auto answer setting in
your communications application.
You can also use the ATS0 command. Refer to
Appendix D, S-registers.
If problems persist, contact your dealer.
9-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Standby/Hibernation
Problem
Procedure
The system will
notenter
Standby/Hibernation
Is Windows Media™ Player open? The system
might not enter Standby/Hibernation, if Windows
Media Player is either playing a selection or
finished playing a selection. Close Windows
Media Player before you select Standby/Hiberna-
tion.
If problems persist, contact your dealer.
LAN
Problem
Procedure
Cannot access LAN
Check for a firm cable connection between the
LAN jack and the LAN HUB.
If problems persist, consult your LAN administra-
tor.
Wireless LAN
If the following procedures do not restore LAN access, consult your LAN adminis-
trator. For more information on wireless communication, refer to Chapter 4, Operat-
ing Basics.
Problem
Procedure
Cannot access
Wireless LAN
Make sure the computer’s wireless
communication switch is set to on.
If problems persist, consult your LAN administra-
tor.
9-27
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
i.LINK (IEEE1394)
Problem
Procedure
i.LINKdevicedoes
notfunction
Make sure the cable is securely connected to
the computer and to the device.
Make sure the device’s power is turned on.
Reinstall the drivers. Open the Windows Control
Panel and double-click the Add New Hardware
icon. Follow the on-screen directions.
Restart Windows.
If problems persist, contact your dealer.
Real Time Clock
Problem
Procedure
Thefollowingmessage The battery for RTC is wearing. Set the date and
is displayed on the LCD: time in BIOS setup with the following steps:
RTC battery is low or
CMOS checksum is
inconsistent. Press
[F1] key to set
1. Press [F1] key. BIOS setup will boot up.
2. Set the date in [System Date].
3. Set the time in [System Time].
4. Press [End] key.
Date/Time.
Confirmationmessagewillappear.
5. Press [Y] key. BIOS setup will terminate and
the computer will be rebooted.
9-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware and system checklist
Printer
Refer also to the Parallel printer sections in Chapter 8, Optional Devices, and to
the troubleshooting and other relevant sections in your printer and software
documentation.
Problem
Procedure
Printer does not
turn on.
Check that the printer is connected to an electric
outlet. Make sure the outlet is supplying power by
plugging in an appliance.
Computer/printer
do not communicate
Make sure the printer is turned on and is
online (ready to use).
Inspect the cable connecting the printer to the
computer for damage. Make sure it is securely
connected.
A parallel printer connects to the parallel port.
Make sure the port is configured correctly. Refer
to Chapter 7, HW Setup and paswords.
Make sure your software is configured to recog-
nize the printer. Check your printer and software
documentation.
Printererror
Checkyourprinterdocumentation.
If problems persist, contact your dealer.
9-29
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
TOSHIBA support
If you require any additional help using your computer or if you are having
problems operating the computer, you may need to contact TOSHIBA for addi-
tional technical assistance.
Before you call
Some problems you experience may be related to software or the operating system,
it is important to investigate other sources of assistance first. Before contacting
TOSHIBA,trythefollowing:
❑
Review troubleshooting sections in the documentation for software and
peripheraldevices.
❑
If a problem occurs when you are running software applications, consult the
software documentation for troubleshooting suggestions. Call the software
company’s technical support for assistance.
❑
Consult the dealer you purchased your computer and/or software from. They
are your best sources for current information and support.
Where to write
If you are still unable to solve the problem and suspect that it is hardware related,
write to TOSHIBA at the nearest location listed below:
9-30
Download from Www.Somanuals.com. All Manuals Search And Download.
TOSHIBA support
OutsideofEurope
InEurope
Germany&Austria
TOSHIBAEurope(I.E.)GmbH
Australia
TOSHIBAAustraliaPty.Ltd.
InformationSystemsDivision
84-92TalaveraRoad
NorthRydeN.S.W.2113
Sydney
Geschäftsbereich,
Deutschland-Österreich
Hammfelddamm8,
D-41460Neuss,Germany
France
Canada
TOSHIBASystèmsFranceS.A.
7,RueAmpèreB.P.131,
92804PuteauxCedex
Netherlands
TOSHIBAofCanadaLtd.
191McNabbStreet,
Markham,Ontario
L3R8H2
TOSHIBAInformationSystems,
BeneluxB.V.
China
TOSHIBAComputerSystems
(Shanghai) Co., Ltd.
RiviumBoulevard
412909LKCapellea/dIJssel
Spain
Bldg.33,No.351,JinzangRoad,
Pudong New Area,
TOSHIBAInformationSystems,
ESPAÑA
Shanghai,
P.R.China201206
ParqueEmpresarialSanFernando
EdificioEuropa,la Planta,
EscaleraA28830Madrid
UnitedKingdom
Singapore
TOSHIBASingaporePte.Ltd.
438BAlexandraRoad#06-01
AlexandraTechnopark
Singapore119968
TOSHIBAInformationSystems(U.K.)
Ltd.
UnitedStatesofAmerica
TOSHIBACourt
TOSHIBAAmericaInformation
Systems, Inc.
Weybridge Business Park
Addlestone Road
9740IrvineBoulevard
Irvine,California92618
USA
Weybridge,SurreyKT152UL
TheRestofEurope
TOSHIBAEurope(I.E.)GmbH
Geschäftsbereich,
Deutschland-Österreich
Hammfelddamm8,
D-41460Neuss,Germany
9-31
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
9-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendixes
AppendixA
Specifications............................................................................... A-1
AppendixB
Display Controller and Modes ..................................................... B-1
AppendixC
ATCommands ............................................................................. C-1
Appendix D
S-registers .................................................................................... D-1
Appendix E
V.90 ............................................................................................... E-1
Appendix F
Internal Modem Guide ................................................................. F-1
Appendix G
WirelessLAN ................................................................................ G-1
Appendix H
AC Power Cord and Connectors ................................................. H-1
Appendix I
PartsNumbers .............................................................................. I-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
This appendix summarizes the computer’s technical specifications.
Physical Dimensions
Size 337(w)x298(d)x40/46(h)millimeters(not including
parts that extend beyond the main body)
Weight 3.5kilograms,configuredwith:15"XGA-TFT,CD-RW/
DVD-ROMdrive,Modem,LAN,IEEE1394,
WirelessLAN
Weight will vary with other configurations.
Environmental Requirements
Ambient
Conditions temperature
Relative
humidity
Operating 5°C(41°F)to35°C(95°F)
Non-operating -20°C(-4°F)to55°C(131°F)
ThermalGradient 20°C perhourmaximum
Wet-bulb temperature 26°Cmaximum
Conditions Altitude(fromsealevel)
Operating -60to3,000meters
20%to80%
10%to90%
Non-operating -60to10,000metersmaximum
Power Requirements
AC adaptor 100-240voltsAC
50 or 60 hertz (cycles per second)
Computer 15VDC
8.0amperes
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Built-in Modem
Networkcontrolunit(NCU)
Type of NCU AA
Type of line Telephone line (analog only)
Type of dialing Pulse
Tone
Controlcommand AT commands
EIA-578commands
Monitor function Computer’s speaker
Communicationspecifications
Communication Data:
system Fax:
Fullduplex
Halfduplex
Communication Data
protocol
ITU-T-Rec
V.21/V.22/V.22bis/V.32
(FormerCCITT)
Bell
/V.32bis/V.34/V.90
103/212A
Fax
ITU-T-Rec
(FormerCCITT)
V.17/V.29/V.27ter
/V.21ch2
Communication Data transmission and reception
speed 300/1200/2400/4800/7200/9600/12000/14400/
16800/19200/21600/24000/26400/28800/31200/
33600bps
Data reception only with V.90
28000/29333/30666/32000/33333/34666/36000/37333/
38666/40000/41333/42666/44000/45333/46666/48000/
49333/50666/52000/53333/54666/56000bps
Fax
2400/4800/7200/9600/12000/14400bps
Transmittinglevel -10dBm
Receivinglevel -10to-40dBm
Input/output 600ohms±30%
impedance
Errorcorrecting MNPclass4andITU-TV.42
Data compression MNP class 5 and ITU-T V.42bis
Power supply +3.3V(suppliedbycomputer)
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Display Controller and
Modes
Display controller
The display controller interprets software commands into hardware commands that
turn particular pels on or off.
The controller is an advanced Video Graphics Array (VGA) that provides Extended
Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support
for the internal LCD and external monitors. The 15.0" TFT LCD panel displays up to
1024horizontaland768verticalpixelsand1400horizontaland1050verticalpixels.
A high-resolution external monitor connected to the computer can display
up to 2048 horizontal and 1536 vertical pixcels at 16M colors
The display controller also controls the video mode, which uses industry standard
rules to govern the screen resolution and the maximum number of colors that can be
displayed on screen.
Software written for a given video mode will run on any computer that supports the
mode.
The computer’s display controller supports all VGA and SVGA modes, the most
widely used industry standards.
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Video modes
The computer supports video modes defined in the tables below. If your application
offers a selection of mode numbers that do not match the numbers on the table,
select a mode based on mode type, resolution, character matrix, number of colors
and refresh rates. Also, if your software supports both graphics and text modes, the
screen display may appear to operate faster using a text mode.
Table1 Video modes (VGA)
Video Type Resolution
mode
Character LCD
CRT
colors
Scanning
frequency
Vertical (Hz)
matrix
(pels)
colors
0, 1
2, 3
VGA 40 × 25
8 × 8
16 of 256K 16 of 256K 70
16 of 256K 16 of 256K 70
16 of 256K 16 of 256K 70
16 of 256K 16 of 256K 70
16 of 256K 16 of 256K 70
16 of 256K 16 of 256K 70
Text
Characters
VGA 80 × 25
8 × 8
Text
Characters
0*, 1* VGA 40 × 25
8 × 14
8 × 14
9 × 16
9 × 16
8 × 8
Text
Characters
2*, 3* VGA 80 × 25
Text
Characters
0+, 1+ VGA 40 × 25
Text
Characters
2+, 3+ VGA 80 × 25
Text
Characters
4, 5
6
VGA 320 × 200
Grph Pels
4 of 256K
2 of 256K
4 of 256K
2 of 256K
70
70
VGA 640 × 200
Grph Pels
8 × 8
7
VGA 80 × 25
9 × 14
9 × 16
Mono
Mono
Mono
Mono
70
70
Text
VGA 80 × 25
Text Characters
Characters
7+
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Table1 Video modes (VGA) continued
Video Type Resolution
mode
Character LCD
CRT
colors
Scanning
frequency
Vertical (Hz)
matrix
(pels)
colors
D
E
VGA 320 × 200
Grph Pels
8 × 8
16 of 256K 16 of 256K 70
16 of 256K 16 of 256K 70
VGA 640 × 200
Grph Pels
8 × 8
F
VGA 640 × 350
Grph Pels
8 × 14
8 × 14
Mono
Mono
70
10
VGA 640 × 350
Grph Pels
16 of 256K 16 of 256K 70
11
12
VGA 640 × 480
Grph Pels
VGA 640 × 480
Grph Pels
8 × 16
8 × 16
2 of 256K
2 of 256K
60
16 of 256K 16 of 256K 60
256 of 256K 256 of 256K 70
13
VGA 320 × 200
Grph Pels
8 × 8
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Table 2 Video modes (XGA)
Resolution
LCD
CRT
Vertical
colors
colors
frequency (Hz)
640 × 480
256/256K
256/256K
256/256K
256/256K
256/256K
60
75
85
100
800 × 600
256/256K
256/256K
60
75
85
100
1024 × 768
1280 × 1024
60
75
85
100
256/256K
(Virtual)
60
75
85
100
1400 × 1050
1600 × 1200
256/256K
(Virtual)
256/256K
256/256K
60
75
85
256/256K
(Virtual)
60
75
85
100
1920 × 1440
2048 × 1536
256/256K
(Virtual)
256/256K
256/256K
60
75
85
256/256K
(Virtual)
60
75
CAUTION: Some SVGA modes are not supported at LCD+CRT simulta-
neous mode and LCD+CRT Multi Monitor mode.
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Table 2 Video modes (XGA) continued
Resolution
LCD
colors
CRT
colors
Vertical
frequency (Hz)
640 × 480
64K/64K
64K/64K
64K/64K
64K/64K
64K/64K
60
75
85
100
800 × 600
64K/64K
64K/64K
60
75
85
100
1024 × 768
1280 × 1024
60
75
85
100
64K/64K
(Virtual)
60
75
85
100
1400 × 1050
1600 × 1200
64K/64K
(Virtual)
64K/64K
64K/64K
60
75
85
64K/64K
(Virtual)
60
75
85
100
1920 × 1440
2048× 1536
64K/64K
(Virtual)
64K/64K
64K/64K
60
75
85
64K/64K
(Virtual)
60
75
CAUTION: Some SVGA modes are not supported at LCD+CRT simulta-
neous mode and LCD+CRT Multi Monitor mode.
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Table 2 Video modes (XGA) continued
Resolution
LCD
CRT
Vertical
colors
colors
frequency (Hz)
640 × 480
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
60
75
85
100
800 × 600
60
75
85
100
1024 × 768
1280 × 1024
60
75
85
100
16M/16M
(Virtual)
60
75
85
100
1400 × 1050
1600 × 1200
16M/16M
(Virtual)
16M/16M
16M/16M
60
75
85
16M/16M
(Virtual)
60
75
85
100
1920 × 1440
2048 × 1536
16M/16M
(Virtual)
16M/16M
16M/16M
60
75
85
16M/16M
(Virtual)
60
75
CAUTION: Some SVGA modes are not supported at LCD+CRT simulta-
neous mode and LCD+CRT Multi Monitor mode.
B-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Table 3 Video modes (Super XGA+)
Resolution
LCD
CRT
Vertical
colors
colors
frequency (Hz)
640 × 480
256/256K
256/256K
256/256K
256/256K
256/256K
256/256K
256/256K
256/256K
256/256K
60
75
85
100
800 × 600
60
75
85
100
1024 × 768
1280 × 1024
60
75
85
100
60
75
85
100
1400 × 1050
1600 × 1200
256/256K
256/256K
60
75
85
256/256K
(Virtual)
60
75
85
100
1920 × 1440
2048 × 1536
256/256K
(Virtual)
256/256K
256/256K
60
75
85
256/256K
(Virtual)
60
75
CAUTION: Some SVGA modes are not supported at LCD+CRT simulta-
neous mode and LCD+CRT Multi Monitor mode.
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Table 3 Video modes (Super XGA+) continued
Resolution
LCD
CRT
Vertical
colors
colors
frequency (Hz)
640 × 480
64K/64K
64K/64K
64K/64K
64K/64K
64K/64K
64K/64K
64K/64K
64K/64K
64K/64K
60
75
85
100
800 × 600
60
75
85
100
1024 × 768
1280 × 1024
60
75
85
100
60
75
85
100
1400 × 1050
1600 × 1200
64K/64K
64K/64K
60
75
85
64K/64K
(Virtual)
60
75
85
100
1920 × 1440
2048 × 1536
64K/64K
(Virtual)
64K/64K
64K/64K
60
75
85
64K/64K
(Virtual)
60
75
CAUTION: Some SVGA modes are not supported at LCD+CRT simulta-
neous mode and LCD+CRT Multi Monitor mode.
B-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
Table 3 Video modes (Super XGA+) continued
Resolution
LCD
CRT
Vertical
colors
colors
frequency (Hz)
640 × 480
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
16M/16M
60
75
85
100
800 × 600
60
75
85
100
1024 × 768
1280 × 1024
60
75
85
100
60
75
85
100
1400 × 1050
1600 × 1200
16M/16M
16M/16M
60
75
85
16M/16M
(Virtual)
60
75
85
100
1920 × 1440
2048 × 1536
16M/16M
(Virtual)
16M/16M
16M/16M
60
75
85
16M/16M
(Virtual)
60
75
CAUTION: Some SVGA modes are not supported at LCD+CRT simulta-
neous mode and LCD+CRT Multi Monitor mode.
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Display Settings
1. You cannot move from the [Settings] tab of [Display Properties] to the
multi-monitor when you are using the display of the computer and an external
CRT display at the same time.
❑ The [Settings] tab is displayed in the following steps;
a. Open [Control Panel], click [Appearance and Themes]
b.Click[display]
c. Select [Settings] tab
FigureB-1 Display Properties
B-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
❑ The way to move to multi-monitor
a. Press [Ctrl] + [Alt] + [F12] keys to make
[Intel(R) 82852/82855 GM/GME Graphics Controller Prope...]
displayed.(SeeFigureB-2)
b. Click
in the left of [Devices] tab (See FigureB-2), then select
[Extended Desktop].
c. Check that the Primary Device is fixed into Note Book (the display of the
computer) and the Secondary Device is being fixed into Monitor
(CRTdisplay).
FigureB-2 Intel(R) 82852/82855 GM/GME Graphics Controller Prope...
B-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
2. Some reproduced DVD picture may not be displayed when the display of the
computer and a CRT display are used at the same. Reduce the resolution, use
the display of the computer only, use the CRT display only or set display
device inthemulti-monitor,thenplayDVD.
Please refer to External monitor in the online manual of Chapter8
Optional Devices or the application guide for the setting of each
display device.
3. The reproduced picture may be up and down slightly in some DVD titles when
reproduced by WinDVD 4.0. The swing can be suppressed by the following
procedure:
a. Boot up WinDVD 4.0 and click the circled part shown in figure B-3, then
select [Display] out of the list.
Figure B-3 WinDVD 4.0
b. The following sub-panel is displayed, then click the circled part
shown in figure B-5.
Figure B-4 WinDVD 4.0 Sub-panel
B-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
c. The following [Set up] screen is displayed, then remove the check of
[Use Hardware Decode Acceleration]
(The check of [Use Hardware Color Acceleration]is
removedautomatically).
Figure B-5 Setup
d. Click [OK] button(The [Set up] tab closes automatically).
4. The DVD video overlay is not displayed when the display mode of CRT
display is set to high resolution and hifh refresh rate mode at LCD/CRT
simultinousormulti-monitor.
Please decrease the resolution and refresh rate of CRT display.
B-13
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
5. A DVD-reproduced image may not be displayed in correct position when you
press Fn+F1 to enter into Instant Security mode while a DVD is playing under
WinDVD 4.0, and then move the mouse or press the key to exit Instant
Security mode. In this case, close WinDVD 4.0 and open it again, or pres the
Stop button and then the Play button to display the DVD image in correct
position.
The following steps will work around this problem.
a. Run WinDVD 4.0. Click the Subpanel button and select the Display
option fromthelist.
b. In the Subpanelwindow, click the Setup button.
c. In the Setupwindow, deselect the Hardware decode acceleration
checkbox (Deselecting this checkbox will automatically deselect the
Hardware color acceleration checkbox).
d. Click the OK button (The Setup tab panel will close).
B-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
AT Commands
In most cases, you will not need to type AT commands manually. However,
there might be some occasions when you will need to do so.
This chapter describes AT commands for data mode. Fax and voice commands
are taken care of by application software.
The format for entering AT commands is:
ATXn
where X is the AT command, and n is the specific value for that command. After
you type in the command press Enter.
Any command issued is acknowledged with a response in either text or numeric
values known as result codes.
All commands and command-values accepted by the modem are described in
this section; any entry other than those listed results in an error.
+++ Escape sequence
The escape sequence allows the modem to exit data mode and enter
on-line command mode. While in on-line command mode, you can
communicate directly to your modem using AT commands. Once you
finish, you can return to data mode using the ATO command.
A pause, the length of which is set by Escape Guard Time (S12), must
be completed after an escape sequence is entered, This pause prevents
the modem from interpreting the escape sequence as data.
The value of the escape sequence character may be changed using
registerS2.
A/
Repeat last command
This command repeats the last command string entered. Do not
precede this command with an AT prefix or conclude it by pressing
Enter.
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
A
Answer command
This command instructs the modem to go off-hook and answer an
incomingcall.
Bn
Communication standard setting
This command determines the communication standard CCITT or Bell.
B0
Selects CCITT V.22 mode when the modem is at 1200 bps.
Selects Bell 212A when the modem is at 1200 bps (default).
Selects V.21 when the modem is at 300 bps.
B1
B15
B16
Selects Bell 103J when the modem is at 300 bps (default).
Result Codes:
OK
n=0,1,15,16
ERROR Otherwise
Dn
Dial
This command instructs the modem to dial a telephone number. Enter n
(the telephone number and any modifiers) after the ATD command.
Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone
digits. Characters such as spaces, hyphens, and parentheses do not
count. They are ignored by the modem, but you may want to include
them to make the number and modifiers easier to read.
The following may be used as phone number modifiers:
P
T
,
Pulsedialing.
Touch-tone dialing (default).
Pause during dialing. Pause for time specified in Register S8
before processing the next character in the dial string.
W
@
Wait for dial tone. Modem waits for a second dial tone before
processing the dial string.
Wait for quiet answer. Wait for five seconds of silence after
dialing the number. If silence is not detected, the modem
sends a NO ANSWER result code back to the caller.
!
Hook flash. Causes the modem to go on-hook for 0.5 seconds
and then return to off-hook.
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
;
Return to command mode. Causes the modem to return to
command mode after dialing a number, without disconnecting
the call.
S=n
Dial a telephone number previously stored using the &Zn=X
command(See&Zn=Xcommandformoreinformation).The
range is 0-3.
En
Echo command
This command controls whether or not the characters entered from
your computer keyboard are displayed on your monitor (echoed) while
the modem is in command mode.
E0
E1
Disables echo to the computer.
Enables echo to the computer (default).
Result Codes:
OK n=0,1
ERROR Otherwise
Hn
Hook control
This command instructs the modem to go on-hook to disconnect a call,
or off-hook to make the phone line busy.
H0
H1
Modem goes on-hook (default).
Modem goes off-hook.
Result Codes:
OK n=0,1
ERROR Otherwise
In
Request ID information
This command displays product information about the modem.
I0
I3
I9
Returns modem identity string and driver version number.
Same as I0.
Returns region ID in English.
Result Codes:
OK
n=0,3,9
ERROR Otherwise
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Ln
Monitor speaker volume
This command sets speaker volume to low, medium, or high.
L0
L1
L2
L3
Lowvolume.
Lowvolume.(SameasL0)
Mediumvolume(default).
Highvolume.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
Mn
Monitor speaker mode
This command turns the speaker on or off.
M0
M1
The speaker is off.
The speaker is on until the modem detects the carrier signal
(default).
M2
M3
The speaker is always on when modem is off-hook.
Speaker is on until the carrier is detected, except when dialing.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
Nn
Modulation handshake
This command controls whether or not the local modem performs a
negotiated handshake at connection time with the remote modem when
the communication speed of the two modems is different.
N0
When originating or answering, this is for handshake only at
the communication standard specified by S37 and the ATB
command.
N1
When originating or answering, begin the handshake at the
communication standard specified by S37 and the ATB
command(default).
During handshake, a lower transmission speed may be
selected.
C-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Result Codes:
OK n=0,1
ERROR Otherwise
On
Return on-line to data mode
O0
O1
O3
Instructs the modem to exit on-line command mode and return
to data mode (see AT escape sequence, +++).
This command issues a retrain before returning to on-line data
mode.
This command issues a rate renegotiation before returning to
on-line data mode.
Result Codes:
OK
n=0,1,3
ERROR Otherwise
P
Select pulse dialing
This command configures the modem for pulse (non touch-tone)
dialing. Dialed digits are pulsed until a T command or dial modifier is
received. Tone dial is the default setting.
Qn
Result code control
Result codes are informational messages sent from the modem and
displayed on your monitor. Basic result codes are OK, CONNECT,
RING, NO CARRIER, and ERROR. The ATQ command allows the
user to turn result codes on or off.
Q0
Enables modem to send result codes to the computer (de-
fault).
Q1
Disables modem from sending result codes to the computer.
Result Codes:
OK n=0,1
ERROR Otherwise
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
T
Select tone dialing
This command instructs the modem to send DTMF tones while dialing.
Dialed digits are tone dialed until a P command or dial modifier is
received. This is the default setting.
Vn
DCE response format
This command controls whether result codes (including call progress
and negotiation progress messages) are displayed as words or their
numeric equivalents.
V0
V1
Displays result codes as digits.
Displays result codes as text (default).
Result Codes:
OK n=0,1
ERROR Otherwise
Xn
Result code selection, call progress monitoring
This command selects which result codes will be used by the modem.
Command Dial tone
detect
Busysignal SupportedResult
detect
Code
X0
X1
X2
X3
Disable
Disable
Enable
Disable
Disable
OK, CONNECT, RING, NO CARRIER,
ERROR
Disable
Disable
Enable
OK, RING, NO CARRIER, ERROR,
CONNECT <RATE>
OK, RING, NO CARRIER, ERROR,
NODIALTONE, CONNECT <RATE>
OK, RING, NO CARRIER, ERROR,
BUSY, CONNECT <RATE>,
BLACKLISTED
X4 (default) Enable
Enable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, BUSY, CONNECT
<RATE>, DELAYED, BLACKLISTED,
REORDER, WARBLE, CALL WAITING
DETECTED
C-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
X5
Enable
Enable
OK, RING, NO CARRIER, ERROR,
NODIALTONE, BUSY, CONNECT
<RATE>, RRING, NO BONGTONE,
DELAYED, BLACKLISTED, REORDER,
WARBLE, CALL WAITING DETECTED
Dial tone detect
Disabled: The modem dials a call regardless of whether it detects a
dial tone.
Enabled: The modem dials only upon detection of a dial tone, and
disconnects the call if the dial tone is not detected within
10 seconds.
Busy tone detect
Disabled: The modem ignores any busy tones it receives.
Enabled: The modem monitors for busy tones.
Result Codes:
OK
n=0,1,2,3,4,5
ERROR Otherwise
Zn
Recall stored profile
The modem performs a soft reset and restores (recalls) the configura-
tion profile according to the parameter supplied. If no parameter is
specified, zero is assumed. Either Z0 or Z1 restores the profile.
Result Codes:
OK
n=0,1
ERROR Otherwise
&Cn Data Carrier Detect (DCD) control
Data Carrier Detect is a signal from the modem to the computer
indicating that a carrier signal is being received from a remote modem.
DCD normally turns off when the modem no longer detects the carrier
signal.
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
&C0
&C1
The state of the carrier from the remote modem is ignored.
DCD circuit is always on.
DCD turns on when the remote modem’s carrier signal is
detected, and off when the carrier signal is not detected
(default).
Result Codes:
OK
n=0,1
ERROR Otherwise
&Dn DTR control
This command interprets how the modem responds to the state of the
DTR signal and changes to the DTR signal.
&D0
Ignore. The modem ignores the true status of DTR and treats
it as always on. This should only be used if your communica-
tion software does not provide DTR to the modem
&D1
If the DTR signal is not detected while in on-line data mode,
the modem enters command mode, issues an OK result code,
and remains connected.
&D2
&D3
If the DTR signal is not detected while in on-line data mode,
the modem disconnects (default).
Reset on the on-to-off DTR transition.
Result Codes:
OK
n=0,1,2,3
ERROR Otherwise
&F
Load factory settings
This command loads the configuration stored and programmed at the
factory. This operation replaces all of the command options and the S-
register settings in the active configuration with factory values.
&F
Recall factory setting as active configuration.
C-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
&Gn V.22bis guard tone control
This command determines which guard tone, if any, to transmit while
transmitting in the high band (answer mode). This command is only
used in V.22 and V.22bis mode. This option is not used in North
America and is for international use only.
&G0
&G1
&G2
Guard tone disabled (default).
Sets guard tone to 550 Hz.
Sets guard tone to 1800 Hz.
Result Codes:
OK
n=0,1,2
ERROR Otherwise
&Kn Local flow control selection
&K0
&K3
&K4
Disableflowcontrol.
EnableCTS/RTSflowcontrol(default).
EnableXON/XOFFflowcontrol.
Result Codes:
OK
n=0,3,4
ERROR Otherwise
&Pn Select Pulse Dial Make/Break Ratio (WW)
&P0
&P1
&P2
Selects 39% - 61% make/break ratio at 10 pulses per second.
Selects 33% - 67% make/break ratio at 10 pulses per second.
Selects 33% - 67% make/break ratio at 20 pulses per second.
Result Codes:
OK
n=0,1,2
ERROR Otherwise
&Tn Self-test commands
These tests can help to isolate problems if you experience periodic
data loss or random errors.
C-9
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
&T0
&T1
Abort. Stops any test in progress.
Local analog loop. This test verifies modem operation, as well
as the connection between the modem and computer. Any
data entered at the local DTE is modulated, then demodulated,
and returned to the local DTE. To work properly, the modem
must be off-line.
Result Codes:
OK
n=0
CONNECT
ERROR
n=1
Otherwise
&V
Display Current Configuration
This command displays the current configuration of the modem. If
nonvolatile memory is supported the stored profiles are displayed
as well.
&V
Viewprofiles.
&W Store current configuration
Saves the current (active) configuration (profile), including S-Regis-
ters.
The current configuration comprises a list of storable parameters
illustrated in the &V command. These settings are restored to the
active configuration upon receiving a Zn command or at power up.
Refer to the &V command.
&W
Stores the current configuration.
&Zn=x
Store telephone number
This command is used to store up to four dialing strings in the
modem’s nonvolatile memory for later dialing. The format for the
command is &Zn=“stored number” where n is the location 0-3 to which
the number should be written. The dial string may contain up to 34
characters. The ATDS=n command dials using the string stored in
location n.
Result codes:
OK
n=0, 1, 2, 3
ERROR Otherwise
C-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
\Nn Error control mode selection
This command determines the type of error control used by the modem
when sending or receiving data.
\N0
\N1
\N2
Buffer mode. No error control.
Directmode.
MNP or disconnect mode. The modem attempts to connect
using MNP2-4 error control procedures. If this fails, the
modem disconnects.
This is also known as MNP reliable mode.
V.42,MNP,orbuffered(default).
\N3
\N4
The modem attempts to connect in V.42 error control mode. If
this fails, it attempts to connect in MNP mode. If this fails, it
connects in buffer mode and continues operation. This is also
known as V.42/MNP auto reliable mode (same as &Q5).
V.42 or disconnect. The modem attempts to connect in V.42
error control mode. If this fails, the modem disconnects.
\N5
\N7
V.42. MNP or buffered (same as\N3).
V.42. MNP or buffered (same as\N3).
Result Codes:
OK
n=0,1,2,3,4,5,7
ERROR Otherwise
\Qn Local flow control selection
\Q0
\Q1
\Q3
Disableflowcontrol.
XON/XOFFsoftwareflowcontrol.
CTS/RTStoDTE(default).
Result Codes:
OK
n=0,1,3
ERROR Otherwise
C-11
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
\Vn Protocol result code
\V0
Disable protocol result code appended to DCE speed.
\V1
Enable protocol result code appended to DCE speed (default).
Result Codes:
OK n=0,1
ERROR Otherwise
%B View numbers in blacklist
If blacklisting is in effect, this command displays the numbers for
which the last call attempted in the past two hours failed. The ERROR
result code appears in regions that do not require blacklisting.
%Cn Data compression control
This command determines the operation of V.42bis and MNP class 5
data compression. On-line changes do not take effect until a discon-
nect occurs first.
%C0
%C3
V.42bis/MNP 5 disabled. No data compression.
V.42bis/MNP 5 enabled. Data compression enabled (default).
Result Codes:
OK n=0,3
ERROR Otherwise
C-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
S-registers
S-registers contain the settings that determine how a number of functions of the
internal modem operate. For example, how many times to let the telephone ring
before the modem answers and how long to wait before it hangs up if a connec-
tion fails. You can also customize certain AT commands such as the escape
sequence and command line termination.
The contents of the registers are changed automatically when you modify
corresponding settings in your communication software. If you choose,
however, you can display and edit the contents of the registers manually when
the modem is in command mode. If the value is out of the acceptable range, then
an error is generated.
This chapter describes the settings for each S-register.
S-register values
The format for displaying the value of an S-register is:
ATSn?
where n is the register number. After you type in the register press Enter.
The format for modifying the value of an S-register is:
ATSn=r
where n is the register number, and r is the new register value. After you type in
the register and its new value press Enter.
NOTE: Some registers vary from one country/region to another.
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
S0
Auto answer ring number
This register determines the number of rings the modem will count
before automatically answering a call. Enter 0 (zero) if you do not want
the modem to automatically answer at all. When disabled, the modem
can only answer with an ATA command.
Range: 0-255
Default: 0
Units: rings
S1
S2
Ring counter
This register is read only. The value of S1 is incremented with each
ring. If no ring occurs over a six-second interval, this register is
cleared.
Range: 0-225
Default: 0
Units: rings
AT escape character (user defined)
This register determines the ASCII values used for an escape se-
quence. The default is the + character. The escape sequence allows the
modem to exit data mode and enter command mode when on-line.
Values greater than 127 disable the escape sequence.
Range: 0-255,ASCIIdecimal
Default: 43
Units: ASCII
S3
Command line termination character
(user defined)
This register determines the ASCII values as the carriage return
character. This character is used to end command lines and result
codes.
Range: 0-127,ASCIIdecimal
Default: 13(carriagereturn)
Units: ASCII
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
S4
S5
Response formatting character (user defined)
This register determines the ASCII value used as the line feed charac-
ter. The modem uses a line feed character in command mode when it
responds to the computer.
Range: 0-127,ASCIIdecimal
Default: 10(linefeed)
Units: ASCII
Command line editing character (user defined)
This register sets the character recognized as a backspace and pertains
to asynchronous only. The modem will not recognize the backspace
character if it is set to a value that is greater than 32 ASCII. This
character can be used to edit a command line. When the echo com-
mand is enabled, the modem echoes back to the local DTE the back-
space character, an ASCII space character, and a second backspace
character. This means a total of three characters are transmitted each
time the modem processes the backspace character.
Range: 0-127,ASCIIdecimal
Default: 8 (backspace)
Units: ASCII
S6
Wait before dialing
This register sets the length of time, in seconds, that the modem must
wait (pause) after going off-hook before dialing the first digit of the
telephone number. The modem always pauses for a minimum of two
seconds, even if the value of S6 is less that two seconds. The wait for
dial tone call progress feature (W dial modifier in the dial string) will
override the value in register S6. This operation, however, may be
affected by some ATX options according to country/region restric-
tions. In some countries/regions, S6 will set dial tone detect time.
Range: 3-255
Default: 3
Units: seconds
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
S7
Connection completion time-out
This register sets the time, in seconds, that the modem must wait
before hanging up because carrier is not detected. The timer is started
when the modem finishes dialing (originate), or goes off-hook (an-
swer). In originate mode, the timer is reset upon detection of an answer
tone if allowed by county restriction. The timer also specifies the wait
for silence time for the @ dial modifier in seconds. S7 is not associated
with the W dial modifier.
Range: 1-255
Default: 50
Units: seconds
S8
Comma pause time
This register sets the time, in seconds, that the modem must pause
when it encounters a comma (,) in the dial command string. In some
countries/regions, S8 will set both wait before dialing and comma
pause time.
Range: 0-255
Default: 2
Units: seconds
S11 DTMF dialing speed
This register determines the dialing speed which is prefixed for each
country/region.
Range: 50-255
Default: 95
Units: .001 seconds
S12 Escape guard time
This register sets the value (in 20 millisecond increments) for the
required pause after the escape sequence.
Range: 0-255
Default: 50
Units: .02 seconds
D-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
S37 Dial line rate
S37=0(default)
S37=1
maximummodemspeed
reserved
S37=2
1200/75bps
300 bps
S37=3
S37=4
reserved
S37=5
1200bps
S37=6
2400bps
S37=7
4800bps
S37=8
7200bps
S37=9
9600bps
S37=10
S37=11
S37=12
S37=13
S37=14
S37=15
S37=16
S37=17
S37=18
S37=19
12000bps
14400bps
16800bps
19200bps
21600bps
24000bps
26400bps
28800bps
31200bps
33600bps
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
AT command set result codes
The following table shows the result codes.
The result code summary
Result Code
OK
Numeric
Description
0
1
2
3
Commandexecuted
CONNECT
RING
Modem connected to line
A ring signal has been detected
NOCARRIER
Modem lost carrier signal, or does
not detect carrier signal, or does
not detect answer tone
ERROR
4
Invalidcommand
CONNECT1200EC*1
NODIALTONE
5
Connection at 1200 bps
No dial tone detected
Busy signal detected
No quiet answer
6
BUSY
7
NOANSWER
8
CONNECT2400EC*1
CONNECT4800EC*1
CONNECT9600EC*1
CONNECT14400EC*1
CONNECT19200EC*1
CONNECT7200EC*1
CONNECT12000EC*1
CONNECT16800EC*1
CONNECT300EC*1
CONNECT21600EC*1
CONNECT24000EC*1
CONNECT26400EC*1
CONNECT28800EC*1
CONNECT31200EC*1
CONNECT33600EC*1
10
11
12
13
14
24
25
86
40
55
56
57
58
59
60
Connection at 2400 bps
Connection at 4800 bps
Connection at 9600 bps
Connection at 14400 bps
Connection at 19200 bps
Connection at 7200 bps
Connection at 12000 bps
Connection at 16800 bps
Connection at 300 bps
Connection at 21600 bps
Connection at 24000 bps
Connection at 26400 bps
Connection at 28800 bps
Connection at 31200 bps
Connection at 33600 bps
D-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D
Result Code
Numeric
Description
DELAYED*2
88
Delay is in effect for the dialed
number
BLACKLISTED*2
89
90
Dialed number is blacklisted
Blacklistisfull
BLACKLISTFULL*2
*1: EC only appears when the Extended Result Codes configuration option is
enabled. EC is replaced by one of the following symbols, depending upon
the error control method used:
V.42bis - V.42 error control and V.42bis data compression.
V.42 - V.42 error control only.
MNP 5 - MNP class 4 error control and MNP class 5 data compression.
MNP 4 - MNP class 4 error control only.
NoEC - No error control protocol.
*2: In some countries/regions, these result codes may not appear.
D-7
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
D-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E
V.90
The TOSHIBA internal modem uses V.90 technology. The modem is capable of
downstream speeds of 56Kbps (kilobits per second) when connected to an Internet
service provider that supports V.90. As with any modem, the actual throughput
(speed of data transfer) depends on analog telephone line conditions, which can
vary considerably. Therefore, many users will experience throughput in the range of
28-50Kbps under normal telephone line conditions. Upstream data flows at the V.34
rate.
NOTE: V.90 rates can be achieved only when one V.90-capable host
modem is connected to another. The TOSHIBA Internal modem will select
automatically V.34 if the remote modem lacks V.90 capability or if a
combination of network and/or phone line conditions prevent V.90
connection.
V.90 mode
Function
Transmissionspeed
DataV.90
From 56K (maximum) to 28Kbps (minimum)
Receptiononly
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Table E-1 Result codes for a V.90 connection
No.
Result code
Description
70
CONNECT 32000 EC*
CONNECT 36000 EC*
CONNECT 40000 EC*
CONNECT 44000 EC*
CONNECT 48000 EC*
CONNECT 52000 EC*
Connection at 32000 bps
72
74
76
78
80
Connection at 36000 bps
Connection at 40000 bps
Connection at 44000 bps
Connection at 48000 bps
Connection at 52000 bps
82
CONNECT 56000 EC*
CONNECT 28000 EC*
CONNECT 29333 EC*
CONNECT 30666 EC*
CONNECT 33333 EC*
CONNECT 34666 EC*
CONNECT 37333 EC*
CONNECT 38666 EC*
CONNECT 41333 EC*
CONNECT 42666 EC*
CONNECT 45333 EC*
CONNECT 46666 EC*
CONNECT 49333 EC*
CONNECT 50666 EC*
CONNECT 53333 EC*
CONNECT 54666 EC*
Connection at 56000 bps
Connection at 28000 bps
Connection at 29333 bps
Connection at 30666 bps
Connection at 33333 bps
Connection at 34666 bps
Connection at 37333 bps
Connection at 38666 bps
Connection at 41333 bps
Connection at 42666 bps
Connection at 45333 bps
Connection at 46666 bps
Connection at 49333 bps
Connection at 50666 bps
Connection at 53333 bps
Connection at 54666 bps
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E
*EC stands for the Error Control method, which appears only when the extended
result codes configuration option is enabled. EC is replaced by one of the
following symbols, depending on the error control method used.
V42bis V.42 error control and V.42bis data compression
V42 V.42errorcontrolonly
NoEC No error control protocol
AT Command
-V90=* V.90DialLineRate
-V90setsthemaximumV.90downstreamthatthemodemattemptsto
connect.
-V90=0 V.90disabled
-V90=1 V.90enabled:automaticspeedselection-maximummodemspeed
(default)
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix F
Internal Modem Guide
This appendix describes how to install and the remove the internal modem.
CAUTION: Do not disassemble the computer beyond the steps described
in this instruction or touch any components not specifically described.
Installing the internal modem
NOTE: The internal modem is preinstalled. The following is for informa-
tion only.
CAUTION: Refer to General Precations for the attention when keybord
brace is removed.
To install the internal modem follow the procedures below.
Installing the modem board and jack
To install the modem board and jack, follow the steps below.
1. Save your data and turn off the computer.
2. Disconnect the AC adaptor and other peripheral devices.
3. Turn the computer upside down and remove the battery pack.
4. Slide the display latch on the front of the computer to the right and open the
display panel.
5. Insert your fingernail or a thin object under the rim of the keyboard brace and
lift out the brace.
6. Remove two screws securing the keyboard and one screw securing the metal
brace. Lift off the metal brace.
7. Lift up the back of the keyboard, rotate it toward you and lay in face down on
the palm rest.
8. Lift into the left the insulation sheet covering the modem board and secure the
sheet with tape to keep it out of your way.
F-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
9. Remove two screws, which you use later to secure the modem board.
10. Connect the modem board cable and seat the modem board.
11. Secure the modem board with two screws removed in step 9.
13. Seat the insulation sheet to cover the modem board.
14. Insert tabs on the front of the keyboard into corresponding notches on the
computer and seat the keyboard.
15. Two screws secure the keyboard and one screw secures the metal brace.
16. Seat the keyboard brace and press to secure latches.
17. Install the battery pack. Refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, for details.
Removing the internal modem
To remove the internal modem, follow the steps below.
1. Save your data and turn off the computer.
2. Disconnect the AC adaptor and other peripheral devices.
3. Turn the computer upside down and remove the battery pack.
4. Slide the display latch on the front of the computer to the right and open the
display panel.
5. Insert your fingernail or a thin object under the rim of the keyboard brace and
lift out the brace.
6. Remove two screws securing the keyboard and one screw securing the metal
brace. Lift off the metal brace.
7. Lift up the back of the keyboard, rotate it toward you and lay in face down on
the palm rest.
8. Lift into the left the insulation sheet covering the modem board and secure the
sheet with tape to keep it out of your way.
9. Remove two screws and remove the modem board.
10. Disconnect the modem cable.
11. Secure the modem board with two screws removed in step 9.
12. Seat the insulation sheet to cover the modem board.
13. Insert tabs on the front of the keyboard into corresponding notches on the
computer and seat the keyboard.
F-2
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Two screws secure the keyboard and one screw secures the metal brace.
15. Seat the keyboard brace and press to secure latches.
16. Install the battery pack. Refer to Replacing the battery pack section in
Chapter 6, Power and Power-Up Modes, for details.
Refer to the installation procedures for details.
The internal modem is approved by Japan Approvals Institute for Telecommuni-
cations Equipment.
A02-0604JP
F-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
F-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix G
Wireless LAN
Card Specifications
FormFactor
„ MiniPCITypeIII
Compatibility
„ IEEE 802.11 Standard for Wireless LANS
Wi-Fi (Wireless Fidelity) certified by the Wi-Fi
Alliance.The'Wi-FiCERTIFIED'logoisa
certification mark of the Wi-Fi Alliance.
NetworkOperating
System
„ MicrosoftWindows® Networking
Media Access l
Protocol
„ CSMA/CA(CollisionAvoidance)with
Acknowledgment(ACK)
DataRate
„ 54/48/36/24/18/12/9/6 Mb/s (Revision A and G,
Revision B/G, A/B/G combo type)
„ 11/5.5/2/1Mb/s(RevisionB)
„ 108/96/72/48/36/24/18/12Mb/s(TurboMode,
Revision A/B/G combo type)
Radio Characteristics
Radio Characteristics of Wireless LAN Cards may vary according to:
❑
❑
Country/region where the product was purchased
Type of product
Wireless communication is often subject to local radio regulations. Although
Wireless LAN Wireless networking products have been designed for operation in
thelicense-free2.4GHzand5GHzband, localradioregulationsmayimposeanumber
of limitations to the use of wireless communication equipment.
NOTE: Refer to the flyer “Information to the User” for regulatory
information that may apply in your country/region.
G-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
R-FFrequency
„
„
„
Band5GHz(5150-5850MHz)(RevisionA,Turbo
Mode)
Band2.4GHz(2400-2483.5MHz)(RevisionB,
Revision B, B/G, A/B/G combo type)
Modulation
Technique
DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK
(Revision B, Revision B/G, A/B/G combo type)
„
OFDM-BPSK,OFDM-QPSK,OFDM-16QAM,
OFDM-64QAM(RevisionA,GandTurboMode,
Revision B/G, A/B/G combo type)
The range of the wireless signal is related to the Transmit Rate of the wireless
communication.CommunicationsatlowerTransmitrangemaytravellarger
distances.
❑
The range of your wireless devices can be affected when the antennas are
placed near metal surfaces and solid high-density materials.
❑
Range is also impacted due to "obstacles" in the signal path of the radio that
may either absorb or reflect the radio signal.
Supported Frequency Sub-bands
Subject to the radio regulations that apply in the countries/regions, your Wireless
LAN Card may support a different set of 5GHz / 2.4GHz channels.
Consult your Authorized Wireless LAN or TOSHIBA Sales office for information
about the radio regulations that apply in the countries/regions.
Wireless IEEE 802.11 Channels Sets (Revision B and G)
FrequencyRangeChannelID 2400-2483.5MHz
1
2
3
4
5
6
7
8
2412
2417
2422
2427
2432
2437
2442
2447
G-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix G
9
2452
2457*1
10
11
2462
12
2467*2
2472*2
13
*1 Factory-set default channels
*2 Refer to the sheet Approved Countries/Regions for use for the countries/
regions. that in which these channels can be used. When installing Wireless
LAN Cards, the channel configuration is managed as follows:
❑
For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless
LAN Card will automatically start operation at the channel identified by the
Wireless LAN Access Point, When roaming between different access points
the station can dynamically switch to another channel if required.
❑
❑
For Wireless LAN Cards installed in Wireless clients that operating in a peer-
to-peer mode, the card will use the default channel 10.
In a Wireless LAN Access Point, the Wireless LAN card will use the factory-
set default channel (printed in bold), unless the LAN Administrator selected a
different channel when configuring the Wireless LAN Access Point device.
Wireless IEEE 802.11 Channels Sets (Revision A)
FrequencyRangeChannelID 5150-5850 MHz
Note
36
5180
5200
5220
5240
5260
5280
5300
5320
5745
5765
5785
40
44
48
52
56
60
64
149
153
157
161
5805
G-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Wireless Channels Sets (Turbo Mode)
FrequencyRangeChannelID
5150-5850 MHz
Note
42
5210
5250
5290
5760
5800
US only *1
US only *1
US only *1
US only *1
US only *1
50
58
152
160
*1:AvailableArea:US(USA,CANADA)only
G-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix H
AC Power Cord and
Connectors
The power cord’s AC input plug must be compatible with the various international
AC power outlets and the cord must meet the standards for the country/region in
which it is used. All cords must meet the following specifications:
Length:
Minimum2meters
Minimum0.75mm2
Minimum2.5amperes
Wiresize:
Currentrating:
Voltagerating:
125or250VAC
(depending on country/region’s power standards)
Certificationagencies
U.S. and Canada: UL listed and CSA certified
No. 18 AWG, Type SVT or SPT-2 two conductor
Europe:
Austria:
OVE
Italy:
IMQ
Belgium:
Denmark:
Finland:
France:
CEBEC
DEMKO
SETI
The Netherlands:
Norway:
KEMA
NEMKO
SEMKO
SEV
Sweden:
UTE
Switzerland:
UnitedKingdom:
Germany:
VDE
BSI
Australia:
Japan:
AS
DENANHO
In Europe, power cords must be VDE type, H05VVH2-F and two conductor.
For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-
15P (125 V) as designated in the U.S. National Electrical code handbook and the
CanadianElectricalCodePartII.
H-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
The following illustrations show the plug shapes for the U.S.A. and Canada, the
United Kingdom, Australia and Europe.
USA and Canada
United Kingdom
UL approved
BS approved
CSA approved
Australia
Europe
Approved by the
AS approved
appropriate agency
H-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix I
Parts Numbers
The computer configuration and parts numbers, printed on a label on the bottom of
thecomputer,indicatetheCPU,LCD,memory,HDD,ODD, communication,mini
PCI and indent devices.
I-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Configurations
The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label.
The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without
notice.
*Figures indicate the CPU operating speed in megahertz. For example, P2.6 means Mobile Intel® Pentium®4 processor
2.60GHz.
I-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
The terms in this glossary cover topics related to this manual. Alternate naming
is included for reference.
DVD-ROM:DigitalVersatileDisc
Read Only Memory
Abbreviations
AC: alternating current
DVD±RW:DigitalVersatileDisc
Read/Write
AGP: accelerated graphics port
ANSI: American National Standards
Institute
ECP: extended capabilities port
FDD: floppy disk drive
APM: advanced power manager
FIR: fastinfrared
ASCII: AmericanStandardCodefor
Information Interchange
GB: gigabyte
HDD: hard disk drive
BIOS: basic input output system
IDE: integrated drive electronics
CD-ROM: CompactDisc-ReadOnly
Memory
I/O: input/output
CD-RW: CompactDisc-Read/Write
IrDA: Infrared Data Association
IRQ: interrupt request
KB: kilobyte
CMOS: complementarymetal-oxide
semiconductor
CPU: central processing unit
CRT: cathode ray tube
LCD: liquid crystal display
LED: lightemittingdiode
LSI: large scale integration
DC: direct current
DDC: display data channel
DMA: directmemoryaccess
DOS: disk operating system
DVD:digitalversatiledisc
MS-DOS:MicrosoftDiskOperating
System
MB: megabyte
OCR: optical character recognition
(reader)
DVD±R:DigitalVersatileDisc
Recordable
PCB: printed circuit board
DVD-RAM:DigitalVersatileDisc
PCI: peripheral component intercon-
Random Access Memory
nect
Glossary-1
Download from Www.Somanuals.com. All Manuals Search And Download.
adaptor
circuit cards that control external
devices, such as video monitors and
magnetic tape devices.
RAM: randomaccessmemory
RGB: red, green, and blue
(Abbreviationscontinued)
ROM: readonlymemory
RTC: realtimeclock
allocate: To assign a space or
function for a specific task.
alphanumeric: Keyboardcharacters
including letters, numbers and other
symbols, such as punctuation marks or
mathematicalsymbols.
SCSI: small computer system
interface
SIO: serial input/output
alternatingcurrent(AC): Electric
current that reverses its direction of
flow at regular intervals.
SXGA+: super extended graphics
array plus
TFT: thin-filmtransistor
analog signal: A signal whose
characteristics such as amplitude and
frequency vary in proportion to (are an
analog of) the value to be transmitted.
Voice communications are analog
signals.
UART: universal asynchronous
receiver/transmitter
USB: UniversalSerialBus
VESA: VideoElectronicStandards
Association
ANSI: American National Standards
Institute. An organization established
to adopt and define standards for a
variety of technical disciplines. For
example, ANSI defined the ASCII
standard and other information
processing requirements.
VGA: video graphics array
VRT: voltage reduction technology
WXGA: wide extended graphics array
XGA: extended graphics array
A
antistatic: A material used to prevent
the buildup of static electricity.
adaptor: A device that provides an
interface between two dissimilar
electronic devices. For example, the
application: A group of programs
that together are used for a specific
AC adaptor modifies the power from a task such as accounting, financial
wall outlet for use by the computer.
This term also refers to the add-in
planning, spreadsheets, word process-
ing and games.
Glossary-2
Download from Www.Somanuals.com. All Manuals Search And Download.
cache memory
bits is one byte. See also byte.
ASCII: AmericanStandardCodefor
Information Interchange. ASCII code is
a set of 256 binary codes that represent
the most commonly used letters,
numbers, and symbols.
board: A circuit board. An internal
card containing electronic compo-
nents, called chips, which perform a
specific function or increase the
capabilities of the system.
async: Short for asynchronous.
boot: Short for bootstrap. A program
that starts or restarts the computer.
The program reads instructions from a
storage device into the computer’s
memory.
asynchronous: Lackingregulartime
relationship. As applied to computer
communications, asynchronous refers
to the method of transmitting data that
does not require a steady stream of
bits to be transmitted at regular time
intervals.
bps: Bits per second. Typically used
to describe the data transmission
speed of a modem.
B
buffer: The portion of the computer’s
memorywheredataistemporarily
stored. Buffers often compensate for
differences in the rate of flow from one
device to another.
backup: A duplicate copy of files kept
as a spare in case the original is
destroyed.
batch file: A file that can be executed
from the system prompt containing a
sequence of operating system com-
mands or executable files.
bus: An interface for transmission of
signals, data or electric power.
byte: The representation of a single
character. A sequence of eight bits
treated as a single unit; also the
smallest addressable unit within the
system.
binary: The base two number system
composed of zeros and ones (off or
on), used by most digital computers.
The right-most digit of a binary number
has a value of 1, the next a value of 2,
then 4, 8, 16, and so on. For example,
the binary number 101 has a value of 5.
See also ASCII.
C
cachememory: Highspeedmemory
which stores data that increases
BIOS: Basic Input Output System.
The firmware that controls data flow
within the computer. See also firmware.
processor speed and data transfer rate.
When the CPU reads data from main
memory, it stores a copy of this data in
cache memory. The next time the CPU
needs that same data, it looks for it in
the cache memory rather than the main
bit: Derived from "binary digit," the
basic unit of information used by the
computer. It is either zero or one. Eight
Glossary-3
Download from Www.Somanuals.com. All Manuals Search And Download.
capacity
memory, which saves time. The
computer has two cache levels. Level
one is incorporated into the processor
and level two resides in external
memory.
CMOS: ComplementaryMetal-Oxide
Semiconductor. An electronic circuit
fabricated on a silicon wafer that
requires very little power. Integrated
circuitsimplementedinCMOS
technology can be tightly packaged
and are highly reliable.
capacity: The amount of data that can
be stored on a magnetic storage
device such as a diskette (floppy disk)
or hard disk. It is usually described in
terms of kilobytes (KB), where one KB
= 1024 bytes and megabytes (MB),
whereoneMB=1024KB.
cold start: Starting a computer that is
currently off (turning on the power).
COM1,COM2,COM3andCOM4:
The names assigned to the serial and
communication ports.
card: Synonym for board. See board.
commands: Instructions you enter at
the terminal keyboard that direct the
actions of the computer or its periph-
eral devices.
CardBus: An industry standard bus
for32-bitPCcards.
CD-ROM: ACompactDisc-Read
Only Memory is a high capacity disc
that can be read from but not written
to. The CD-ROM drive uses a laser,
rather than magnetic heads, to read
data from the disc.
communications: The means by
which a computer transmits and
receives data to and from another
computer or device. See parallel
interface;serialinterface.
CD-R: ACompactDisc-Recordable
disc can be written once and read
manytimes.SeealsoCD-ROM.
compatibility: 1)Theabilityofone
computer to accept and process data in
the same manner as another computer
without modifying the data or the
media upon which it is being trans-
ferred. 2) the ability of one device to
connect to or communicate with
another system or component.
CD-RW: ACompactDisc-Read/Write
disc can be rewritten many times.
character: Any letter, number,
punctuation mark, or symbol used by
the computer. Also synonymous with
byte.
components: Elements or parts (of a
system) which make up the whole
(system).
chassis: The frame containing the
computer.
computer program: Asetofinstruc-
tions written for a computer that
enable it to achieve a desired result.
chip: A small semiconductor contain-
ing computer logic and circuitry for
processing, memory, input/output
functions and controlling other chips.
Glossary-4
Download from Www.Somanuals.com. All Manuals Search And Download.
dialog box
computer system: Acombinationof
hardware,software,firmware,and
peripheral components assembled to
process data into useful information.
on the display screen.
D
data: Information that is factual,
measurable or statistical that a
computer can process, store, or
retrieve.
configuration: Thespecificcompo-
nents in your system (such as the
terminal, printer, and disk drives) and
the settings that define how your
system works. You use the HW Setup
program to control your system
configuration.
data bits: A data communications
parameter controlling the number of
bits (binary digits) used to make up a
byte. If data bits = 7 the computer
can generate 128 unique characters.
If data bits = 8 the computer can
generate 256 unique characters.
control keys: A key or sequence of
keys you enter from the keyboard to
initiate a particular function within a
program.
DC: Direct Current. Electric current
that flows in one direction. This type
of power is usually supplied by
batteries.
controller: Built-in hardware and
software that controls the functions of
a specific internal or peripheral device
(e.g. keyboard controller).
default: The parameter value
automatically selected by the system
when you or the program do not
provide instructions. Also called a
preset value.
co-processor: A circuit built into the
processor that is dedicated to intensive
math calculations.
CPS: Characters Per Second. Typi-
cally used to indicate the transmission
speed of a printer.
delete: To remove data from a disk or
other data storage device. Synony-
mous with erase.
CPU: Central Processing Unit. The
portion of the computer that interprets
and executes instructions.
devicedriver: Aprogramthat
controls communication between a
specific peripheral device and the
computer. TheCONFIG.SYSfile
contains device drivers that MS-DOS
loads when you turn the computer on.
CRT: Cathode Ray Tube. A vacuum
tube in which beams projected on a
fluorescent screen-producing lumi-
nous spots. An example is the
television set.
dialog box: A window that accepts
user input to make system settings or
record other information.
cursor: A small, blinking rectangle or
line that indicates the current position
Glossary-5
Download from Www.Somanuals.com. All Manuals Search And Download.
disk drive
disk drive: The device that randomly
accesses information on a disk and
copies it to the computer’s memory. It
also writes data from memory to the
disk. To accomplish these tasks, the
unit physically rotates the disk at high
speed past a read-write head.
DVD-RAM:ADigitalVersatileDisc
Random Access Memory is a high-
capacity, high performance disc that
lets you store large volumes of data.
The DVD drive uses a laser to read
data from the disc.
DVD-ROM: ADigitalVersatileDisc
Read Only Memory is a high capacity,
high performance disc suitable for
play back of video and other high-
density files. The DVD drive uses a
laser to read data from the disc.
disk storage: Storing data on magnetic
disk. Data is arranged on concentric
tracks much like a phonograph record.
diskette: A removable disk that stores
magnetically encoded data. Also
called a floppy disk.
DVD-RW: ADigitalVersatileDisc-
Read/Write disc can be rewritten many
times.
display: A CRT, LCD, or other image
producing device used to view
computer output.
DVD±RW: ADigitalVersatile
Disc Read/Write disc can be rewritten
manytimes.
documentation: The set of manuals
and/or other instructions written for the
users of a computer system or applica-
tion. Computer system documentation
typically includes procedural and
tutorial information as well as system
functions.
E
echo: To send back a reflection of the
transmitted data to the sending
device. You can display the informa-
tion on the screen, or output it to the
printer, or both. When a computer
receives back data it transmitted to a
CRT (or other peripheral device) and
then retransmits the data to printer,
the printer is said to echo the CRT.
DOS: Disk Operating System. See
operating system.
driver: A software program, generally
part of the operating system, that
controls a specific piece of hardware
(frequently a peripheral device such as
a printer or mouse).
erase: See delete.
DVD-R: ADigitalVersatileDisc-
Recordable disk can be written once
and read many times.
escape: 1) A code ( ASCII code 27),
signaling the computer that what
follows are commands; used with
peripheral devices such as printers
and modems. 2) A means of aborting
the task currently in progress.
Glossary-6
Download from Www.Somanuals.com. All Manuals Search And Download.
hardware
folder: An icon in Windows used to
store documents or other folders.
escape guard time: A time before and
after an escape code is sent to the
modem which distinguishes between
escapes that are part of the transmitted
data, and escapes that are intended as
a command to the modem.
format: The process of readying a
blank disk for its first use. Formatting
establishes the structure of the disk
that the operating system expects
before it writes files or programs onto
the disk.
execute: To interpret and execute an
instruction.
function keys: The keys labeled F1
through F12 that tell the computer to
perform certain functions.
ExtendedCapabilityPort:Anindustry
standard that provides a data buffer,
switchable forward and reverse data
transmission, and run length encoding
(RLE)support.
G
gigabyte (GB): A unit of data storage
equal to 1024 megabytes. See also
megabyte.
F
fast infrared: An industry standard
that enables cableless infrared serial
data transfer at speeds of up to 4
Mbps.
graphics: Drawings, pictures, or other
images, such as charts or graphs, to
present information.
file: A collection of related informa-
tion; a file can contain data, programs,
or both.
H
firmware: A set of instructions built
into the hardware which controls and
directs a microprocessor’s activities.
hard disk: A non-removable disk
usually referred to as drive C. The
factory installs this disk and only a
trained engineer can remove it for
servicing. Also called fixed disk.
fixed disk: See hard disk.
floppy disk: See diskette.
harddiskdrive(HDD): Anelectro-
mechanical device that reads and
writes a hard disk. See also hard disk.
floppy disk drive (FDD): An electro-
mechanical device that reads and
writes to floppy disks. See also
diskette.
hardware: Thephysicalelectronic
and mechanical components of a
computer system: typically, the
computer itself, external disk drives,
etc. See also software and firmware.
Fn-esse: A TOSHIBA utility that lets
you assign functions to hot keys.
Glossary-7
Download from Www.Somanuals.com. All Manuals Search And Download.
hertz
hertz: A unit of wave frequency that
equals one cycle per second.
the keyboard or external or internal
storage devices. The data sent (or
output) by the sending computer is
input for the receiving computer.
hexadecimal: Thebase16numbering
system composed of the digits 0
through 9 and the letters A, B, C, D, E,
and F.
instruction: Statements or commands
that specify how to perform a particu-
lar task.
host computer: The computer that
controls, regulates, and transmits
information to a device or another
computer.
interface: 1) Hardware and/or
software components of a system
used specifically to connect one
system or device to another. 2) To
physically connect one system or
device to another to exchange
information. 3) The point of contact
between user, the computer, and the
program, for example, the keyboard or
a menu.
hotkey: The computer’s feature in
which certain keys in combination with
the extended function key, Fn, can be
used to set system parameters, such
as speaker volume.
HWSetup:ATOSHIBAutilitythat
lets you set the parameters for various
hardware components.
interrupt request: A signal that gives
a component access to the processor.
I/O: Input/output. Refers to accep-
tance and transfer of data to and from
a computer.
I
icon: A small graphic image displayed
on the screen or in the indicator panel.
In Windows, an icon represents an
object that the user can manipulate.
I/O devices: Equipment used to
communicate with the computer and
transfer data to and from it.
i.LINK(IEEE1394):Thisportenables
high-speed data transfer directly from
external devices such as digital video
cameras.
IrDA 1.1: An industry standard that
enables cableless infrared serial data
transfer at speeds of up to 4 Mbps.
infraredport: Acablelesscommuni-
cations port capable of using infrared
signals to send serial data.
J
jumper: Asmallcliporwirethat
allows you to change the hardware
characteristics by electrically connect-
ing two points of a circuit.
input: The data or instructions you
provide to a computer, communication
device or other peripheral device from
Glossary-8
Download from Www.Somanuals.com. All Manuals Search And Download.
monitor
LSI: Large Scale Integration. 1) A
K
technology that allows the inclusion
of up to 100,000 simple logic gates on
a single chip. 2) An integrated circuit
that uses large scale integration.
K: TakenfromtheGreekwordkilo,
meaning 1000; often used as equiva-
lent to 1024, or 2 raised to the 10th
power. See also byte and kilobyte.
M
KB: See kilobyte.
keyboard: An input device contain-
ing switches that are activated by
manually pressing marked keys. Each
keystroke activates a switch that
transmits a specific code to the
computer. For each key, the transmit-
ted code is, in turn, representative of
the (ASCII) character marked on the
key.
mainboard: Seemotherboard.
megabyte (MB): A unit of data
storage equal to 1024 kilobytes. See
also kilobyte.
megahertz: A unit of wave frequency
that equals 1 million cycles per
second. See also hertz.
menu: A software interface that
displays a list of options on the
screen. Also called a screen.
kilobyte (KB): A unit of data storage
equal to 1024 bytes. See also byte
and megabyte.
microprocessor: A hardware compo-
nent contained in a single integrated
circuit that carries out instructions.
Also called the central processing unit
(CPU), one of the main parts of the
computer.
L
level 2 cache: See cache.
LightEmittingDiode(LED): A
semiconductor device that emits light
when a current is applied.
mode: A method of operation, for
example, the boot mode, standby
mode or the hibernation mode.
LiquidCrystalDisplay(LCD): Liquid
crystal sealed between two sheets of
glass coated with transparent con-
ducting material. The viewing-side
coating is etched into character
forming segments with leads that
extend to the edge of the glass.
Applying a voltage between the glass
sheets alters the brightness of the
liquidcrystal.
modem: Derivedfrommodulator/
demodulator, a device that converts
(modulates) digital data for transmis-
sion over telephone lines and then
converts modulated data (demodu-
lates) to digital format where received.
Glossary-9
Download from Www.Somanuals.com. All Manuals Search And Download.
motherboard
monitor: A device that uses rows and
columns of pixels to display alphanu-
meric characters or graphic images.
See also CRT.
O
OCR: OpticalCharacterRecognition
(reader). A technique or device that
uses laser or visible light to identify
characters and input them into a
storage device.
motherboard: Anamesometimes
used to refer to the main printed circuit
board in processing equipment. It
usually contains integrated circuits
that perform the processor’s basic
functions and provides connectors for
adding other boards that perform
special functions. Sometimes called a
mainboard.
online state: A functional state of a
peripheral device when it is ready to
receive or transmit data.
operating system: A group of
programs that controls the basic
operation of a computer. Operating
system functions include interpreting
programs, creating data files, and
controlling the transmission and
receipt (input/output) of data to and
from memory and peripheral devices.
MP3: An audio compression standard
that enables high-quality transmission
and real-time playback of sound files.
N
output: The results of a computer
operation. Output commonly indicates
data 1) printed on paper, 2) displayed
at a terminal, 3) sent through the serial
port of internal modem, or 4) stored on
somemagneticmedia.
non-system disk: A formatted
diskette (floppy disk) you can use to
store programs and data but you
cannot use to start the computer. See
system disk.
nonvolatilememory: Memory,usually
read-only (ROM), that is capable of
permanentlystoringinformation.
Turning the computer’s power off
does not alter data stored in nonvola-
tilememory.
P
parallel interface: Refers to a type of
information exchange that transmits
information one byte (8 bits) at a time.
See also serial interface.
numerickeypadoverlay:Afeature
that allows you to use certain keys on
the keyboard to perform numeric entry,
or to control cursor and page move-
ment.
Glossary-10
Download from Www.Somanuals.com. All Manuals Search And Download.
prompt
port: The electrical connection
parity: 1)Thesymmetricalrelation-
ship between two parameter values
(integers) both of which are either on
or off; odd or even; 0 or 1. 2) In serial
communications, an error detection bit
that is added to a group of data bits
making the sum of the bits even or
odd. Parity can be set to none, odd, or
even.
through which the computer sends
and receives data to and from devices
or other computers.
PowerSaverUtility:ATOSHIBA
utility that lets you set the parameters
for various power-saving functions.
printedcircuitboard(PCB): A
hardware component of a processor to
which integrated circuits and other
components are attached. The board
itself is typically flat and rectangular,
and constructed of fiberglass, to form
the attachment surface.
password: A unique string of charac-
ters used to identify a specific user.
The computer provides various levels
of password protection such as user,
supervisor and eject.
pel: The smallest area of the display
that can be addressed by software.
Equal in size to a pixel or group of
pixels. Seepixel.
program: A set of instructions a
computer can execute that enables it
to achieve a desired result. See also
application.
peripheralcomponentinterconnect:
An industry standard 32-bit bus.
prompt: A message the computer
provides indicating it is ready for or
requires information or an action from
you.
peripheral device: An I/O device that
is external to the central processor
and/or main memory such as a printer
or a mouse.
pixel: A picture element. The smallest
dot that can be made on a display or
printer. Also called a pel.
plugandplay: Acapabilitywith
Windows that enables the system to
automatically recognize connections
of external devices and make the
necessary configurations in the
computer.
Glossary-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio frequency interference (RFI) shield
ROM: Read Only Memory: A
R
nonvolatilememorychipmanufac-
tured to contain information that
controls the computer’s basic
operation. You cannot access or
change information stored in ROM.
Radiofrequencyinterference(RFI)
shield: A metal shield enclosing the
printed circuit boards of the printer or
computer to prevent radio and TV
interference. All computer equipment
generates radio frequency signals.
The FCC regulates the amount of
signals a computing device can allow
past its shielding. A Class A device is
sufficient for office use. Class B
provides a more stringent classifica-
tion for home equipment use.
S
SCSI:SmallComputerSystem
Interface is an industry standard
interface for connection of a variety of
peripheral devices.
SD cards: Secure Digital cards are
flash memory widely used in a variety
of digital devices such as digital
cameras and Personal Digital Assis-
tants.
TOSHIBA portable computers comply
with Class B computing device
regulations.
RandomAccessMemory(RAM):
High speed memory within the
computer circuitry that can be read or
written to.
SIO: Serial Input/Output. The
electronic methodology used in serial
data transmission.
restart: Resetting a computer without
turning it off (also called “warm boot”
or “soft reset”). See also boot.
soft key: Key combinations that
emulate keys on the IBM keyboard,
change some configuration options,
stop program execution, and access
the numeric keypad overlay.
RGB: Red, green, and blue. A device
that uses three input signals, each
activating an electron gun for a
primary additive color (red, green, and
blue) or port for using such a device.
See also CRT.
software: The set of programs,
procedures and related documentation
associated with a computer system.
Specifically refers to computer
programs that direct and control the
computer system’s activities. See
also hardware.
RJ11: A modular telephone jack.
RJ45: A modular LAN jack.
stop bit: One or more bits of a byte
that follow the transmitted character
or group codes in asynchronous serial
communications.
Glossary-12
Download from Www.Somanuals.com. All Manuals Search And Download.
write protection
subpixel: Three elements, one red,
one green and blue (RGB), that make
up a pixel on the color LCD. The
computer sets subpixels indepen-
dently, each may emit a different
degree of brightness. See also pixel.
U
Universal Serial Bus: This serial
interface lets you communicate with
several devices connected in a chain
to a single port on the computer.
synchronous: Having a constant time
interval between successive bits,
characters or events.
V
VGA:VideoGraphicsArrayisan
industry standard video adaptor that
lets you run any popular software.
system disk: A disk that has been
formatted with an operating system.
For MS-DOS the operating system is
contained in two hidden files and the
COMMAND.COM file. You can boot a
computer using a system disk. Also
called an operating system disk.
volatilememory: Randomaccess
memory (RAM) that stores information
as long as power is supplied to the
computer.
W
T
warm start: Restarting or resetting a
terminal: Atypewriter-likekeyboard
and CRT display screen connected to
the computer for data input/output.
computer without turning it off.
window: A portion of the screen that
can display its own application,
TFT: Thin-filmtransistor,a colorLCD
technology that applies individual
transistors to each pixel enabling fine
display control and excellent screen
legibility.
document or dialog box. Often used to
mean a Microsoft Windows window.
Wireless LAN: Local Area Network
(LAN)throughwirelesscommunica-
tion.
Touch Pad: A pointing device
integrated into the TOSHIBA com-
puter palm rest.
writeprotection: Amethodfor
protecting a diskette (floppy disk) from
accidental erasure.
TTL: Transistor-transistor logic. A
logic circuit design that uses switch-
ing transistors for gates and storage.
Glossary-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
D
ACadaptor 1-3, 2-16
DCIN15Vport 2-6
connecting 3-5
universal 1-13
ASCII characters 5-9
Auto power on, See Power
DCIN15Vindicator 2-9,6-3
Diskettecare 4-17
Display 1-6, 2-8, See also Video
modes and Monitor external
automatic power off 1-9
controller 1-6, Appendix B
hinge 2-8
B
opening 3-6
selection, See Hot keys
Documentation list 1-2
Drag'nDropCD+DVD 1-12,4-15
DVDMultidrive 2-15
location 2-3
using 4-3
writing 4-12
DVD-ROMdrive 2-14
location2-3
Battery, See also Battery pack
charging 6-8
extendinglife 6-11
indicator 2-10,6-2
monitoring capacity 6-10
realtimeclock 1-3,6-4
safety precautions 6-5
save mode 1-10
types 6-3
Batterypack 1-3, 6-4
location 2-7
using 4-3
DVD-R/-RWdrive2-14
location 2-3
replacing 6-12
Bluetooth
SDcard2 1-13
using 4-3
writing 4-11
DVD±RWdrive(DVDDualdrive) 2-15
location 2-3
Boot priority 7-6
C
using 4-3
writing 4-10
CD/DVDinuseindicator 2-5
CD-RW/DVD-ROMdrive 1-4
location 2-3
E
Environment 3-2
problems 9-13
Equipmentchecklist 1-1
Equipment setup
using 4-3
writing 4-8
general conditions 3-2
placement 3-2
Charger, See Battery Charger
Cleaning the computer 4-26
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
Ergonomics
lighting 3-4
seating and posture 3-3
work habits 3-4
HW Setup 1-11
accessing 7-1
BootPriority 7-6
CPU 7-5
Expansionmemory, SeeMemory
expansion
DeviceConfig 7-4
Display 7-5
General 7-2
Keyboard 7-9
LAN 7-9
Password 7-2
USB 7-9
window 7-1
F
Fn + Ctrl (enhanced keyboard
simulation) 5-3
Fn + Enter 5-3
Fn + Esc (sound mute) 5-4
Fn-esse 1-11
Fn + F1 (instant security) 5-4
Fn + F2 (power save mode) 5-4
Fn + F3 (standby) 5-5
Fn + F4 (hibernation) 5-5
Fn + F5 (display selection) 5-5
Fn + F6 (display brightness) 5-5
Fn + F7 (display brightness) 5-6
Fn + F8 (wireless setting) 5-6
Fn + F9 (touch pad) 5-6
Fn+F10(arrowmode) 5-3, 5-7
Fn+F11(numericmode) 5-3,5-8
Fn+F12(ScrLock) 5-3
I
i.LINK 1-7,8-13
Indicators 2-9, 6-2
Instant security, See Hot keys
Interfaces, See Ports
K
Keyboard 1-6,5-1
emulating enhanced keyboard 5-2
F1 . . . F12 function keys 5-2
hot keys 5-4
Typewriter keys 5-1
Keypadoverlay 1-10, 5-7
arrowmode 5-7
Fn Sticky key 5-6
Function Keys 5-2
numericmode 5-8
H
temporarily changing modes 5-9
temporarily using normal keyboard
(overlay on) 5-8
temporarily using overlay
(overlayoff) 5-9
Hard disk drive 1-4
automatic power off 1-9
Heat dispersal 4-27
Hibernation 1-11,5-5
Hotkeys 1-9, 5-4
turning on 5-7
Windows special keys 5-7
display brightness 5-5, 5-6
display selection 5-5
instant security 5-4
power save mode 5-4
sound mute 5-4
standby 5-5
sticky key utility 5-6
wireless setting 5-6
L
LAN 1-8
active indicator 2-2
cable types 4-24
connecting 4-25
disconnecting 4-26
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
jacklocation 2-2
PC card 1-7
using 4-24
inserting 8-2
LCD, See Display, Videomodesand
Monitorexternal
Lock, security, See Security lock
location of slots 2-2
removing 8-3
Ports
DCIN15V 2-6
externalmonitor 1-7,2-5
M
headphone, See Sound system
i.LINK 1-7,2-3
LAN 2-2
microphone, See Sound system
modem 2-4
parallel 2-5
Main battery, See Battery pack
Memory 1-3
expansion 1-13,8-6
installing 8-7
removing 8-10
slots 1-3
video RAM 1-3
Microphone, See sound system,
microphone
Microprocessor, See Processor
Modem 1-8,4-19
connecting 4-21
USB 1-7,2-2,2-6
Power
button location 2-8
indicator 2-9,6-3
panelpoweron/off 1-10,6-16
power up modes 6-15
turning off 3-8
disconnecting 4-22
jack location 2-3
turning on 3-7
system auto off 6-16
properties menu 4-20
region selection 4-19
Monitor external 8-12, See also
Video modes and Ports
Moving the computer 4-26
Problems
AC power 9-5
analyzing the problem 9-2
battery 9-6
CD-RW/DVD-ROMdrive 9-13
DVDMultidrive 9-16
DVD-ROMdrive 9-12
DVD-R/-RWdrive 9-14
DVD±RWdrive
N
Numerickeypad, SeeKeypadoverlay
O
(DVDDualdrive) 9-18
diskette drive 9-19
Hard disk drive 9-11
Hardware and system checklist 9-3
i.LINK 9-28
keyboard 9-7
LAN 9-27
LCDpanel 9-10
memoryexpansion 9-24
modem 9-25
Operating system, See Windows
Overlay, See Keypad overlay
P
Panel power on/off, See Power
Password
power on 1-10
starting the computer by 6-15
supervisor 7-10
user 7-2
monitor,external 9-25
Index-3
Download from Www.Somanuals.com. All Manuals Search And Download.
User's Manual
password 9-7
PCcard 9-20
microphone 1-7,2-5
speakers 2-8
pointing device 9-21
power 9-4
Volumecontrol 2-4
Standby 1-11
preliminarychecklist 9-1
Realtimeclock 9-28
SD card 9-20
System automatic
Standby/Hibernation 1-10
T
self test 9-4
sound system 9-24
standby/hibernation 9-27
supportfromTOSHIBA 9-30
system start-up 9-3
Touch Pad 9-21
USB 9-23
TOSHIBA
TOSHIBA PowerSaver 1-11
TOSHIBA Touch and Launch 1-12
TOSHIBAUtilities 1-9
Touch Pad 1-7, 2-9
control buttons 2-9, 4-1
using 4-1
WirelessLAN 9-27
Processor 1-2
Troubleshooting, See Problems
R
U
Real time clock battery, See Battery
RecoveryDVD-ROM 3-14
Utilities
list 1-11
USB 1-7
S
location 2-2,2-5
USBdiskettedrive 2-11,8-12
connecting 4-2
disconnecting 4-3
using 4-2
Screen, See Display
ScrLock (Fn + F12), See Soft keys
SD card 1-7
indicator 2-2
inserting 8-4
location of slot 2-2
removing 8-5
V
Videomodes, AppendixB
VideoRAM 1-3
Volume control, See sound system
Securitylock 1-9
attaching 8-15
location 2-5
Self Test, See Problems
Sensor switch 2-9
Soft keys 5-2
cursor control keys 5-3
Enter 5-3
W
Wirelesscommunication
indicator 2-4,4-24
switch 2-4,4-23
Wireless LAN 1-8
using 4-22
numeric keypad keys 5-3
rightCtrlkey 5-3
ScrLock 5-3
Work space 3-1
Sound system 1-7
headphone 1-7, 2-5
Index-4
Download from Www.Somanuals.com. All Manuals Search And Download.
|