FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
1900 Series
GENERAL INFORMATION
Tools Required for Proper
Disassembly and Reassembly:
1. Phillips Screwdrivers (Size 1&0)
2. 3mm Flat head Screwdriver
3. Security Torx (Size 6)
4. Case Separator
5. ESD Wrist Strap
6. ESD mat
7. Tweezers
Before attempting any of the following procedures,
make sure that the main battery and AC adaptor is
not connected to the unit and the environment in
which you are working on is protected from
Electro-Static Discharge(ESD).
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
BATTERY PACK REMOVAL
OPTIONAL PC CARD REMOVAL
Battery
release lever
Battery pack
Eject button
PC Card
1. Press the eject button of the PC Card you want to
remove.
2. Press the extended eject button to pop the PC card
out slightly.
3. Grasp the PC Card and pull it out
1. Turn the computer upside down as shown.
2. Slide the battery release lever in the direction of the
arrow.
3. Lift out the battery pack.
4. Separate the battery pack from the battery cover.
NOTE: Before removing any PCMCIA device, make
make it is “STOPPED” in the PC Card Manager.
HDD REMOVAL
M3x3 silver screws
HDD plate
HDD interface
connector
M3x3 silver screws
HDD cover
M2.5x4 black screw
HDD bracket
3. Remove the HDD interface connector.
4. Remove two M3x3 silver screws securing the HDD
plate and lift out the plate.
1. Turn the computer upside down.
2. Remove two M2.5x4 black screw securing
HDD assembly and lift it out.
5. Remove four M3x3 silver screws securing the HDD
bracket and separate the HDD from the bracket..
.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
FDD REMOVAL
M2x3 black screws
Bezel
FDD cable
FDD cable
FDD assy
M2.5x4 black screw
4. Remove two M2x3 black screws securing the
FDD bezel from the FDD and lift out the bezel.
5. Disconnect the FDD cable from the FDD.
1. Remove one M2.5x4 black screw securing the FDD
assembly.
2. Disconnect the FDD cable from the system board.
3. Slide the FDD assembly to the right and lift it out.
MEMORY MODULE REMOVAL
Memory module
Memory clips
M2.5x4 black screws
1. Turn the computer upside down.
2. Remove four M2.5x4 black screws securing the
memory cover.
4. Gently press out on the memory clips and pull the
memory module out of the connector on a 45 degree
angle.
3. Lift out the cover.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
MINI PCI CARD REMOVAL
Mini PCI card
Mini PCI slot cover
M2.5x4 black torx screws
PCI clips
2. Gently press out the Mini PCI slot clips and pull the
Mini PCI card out of the connector on a 30 degree
angle.
1. Remove one M2.5x4 black torx screws securing
the Mini PCI slot cover.
CD-R/W/DVD-ROM DRIVE REMOVAL
Bezel
M2x3 black screws
M2.5x4
black screw
M2x3 black screws
Bracket
DVD-ROM drive
1. Remove one M2.5x4 black screws securing the
DVD-ROM drive.
2. Slide the DVD-ROM drive to the left to disconnect it from
PJ23 on the system board.
3. Remove two M2x3 black screws securing the
CD-R/W/DVD-ROM bracket and lift it out.
4. Remove three M2x3 black screws securing the
CD-R/W/DVD-ROM bezel and lift it out.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
CPU REMOVAL
Heatsink
CPU cover
M2x3 torx screws
M2x4 silver screws
3. Remove four M2x4 silver screws securing the
cooling module.
4. Gently lift up the heatsink.
1. Turn the computer upside down.
2. Remove two M2x3 torx screws securing the CPU cover
CPU REMOVAL
KEYBOARD REMOVAL
Display
panel
Close
Open
Keyboard holder
Keyboard cover release latch
1. Open the display panel.
1. Rotate the CPU lock counter-clockwise, to the OPEN
position, and lift the CPU out of the socket.
2. Insert a fine-tipped tweezers into the keyboard cover
release latch and slide it to the right to release the
latches securing the keyboard holder.
NOTE: When installing the CPU, make sure that a silicone
grease is applied before attaching the heat sink.
3. Lift out the keyboard holder.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
KEYBOARD REMOVAL
Keyboard
cable
PJ113
Keyboard
M2.5x3 black screws
5. Lift out the keyboard and set it on the palm rest.
6. Disconnect the keyboard cable from PJ113 on the
system board and lift out the keyboard.
4. Remove two M2.5x3 black screws securing the
keyboard.
TOP COVER REMOVAL
M2.5x7 black
screws
M2.5x4 black screws
M2.5x7 black screws
M2.5x4 black screw
1. Turn the computer upside down and remove the
following sixteen screws:
- 11 M2.5x4 black screws
2. Turn the computer right side up with the back facing
you.
3. Remove two M2.5x7 black screws and one M2.5x4
black screw securing the top cover.
- 6 M2.5x7 black screws
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
TOP COVER REMOVAL
LCD/FL cable
M2.5x4 black screw
LCD/FL
harness
cover
Power button
Left/Right
speaker
cable
Speaker cover
M2.5x5 silver screws
Power switch board
M2.5x4 black screws
4. Slide the LCD/FL harness cover to the right and lift it out.
5. Remove two M2.5x5 silver screws securing the power
button and the power switch board.
7. Remove two M2.5x4 black screws securing the
speaker cover and lift out the cover.
8. Remove one M2.5x4 black screw securing the
LCD/FL cable bracket. Remove the bracket and
Disconnect the LCD/FL cable from JP1.
9. Disconnect the Left/Right speaker cable from JP7
and JP9 on the system board.
6. Lift out the power button and the power switch board.
TOP COVER REMOVAL
SYSTEM BOARD REMOVAL
System board
JP10
Touchpad
interface
cable
JP11
FDD interface
cable
M2.5x7 black screws
PC card slot buttons
M2.5x4 black screws
10. Remove the mylar tape and disconnect the FDD interface
cable from JP11 on the system board.
1. Remove two M2.5x4 black screws securing the
system board.
11. Disconnect touchpad interface cable from JP10 on the
system board.
12. Remove nine M2.5x7 black screws securing the top cover.
13. Using the case separator, separate the top cover from the
bottom cover
2. Push the PC card slot buttons in or gently spread the
bottom plastic close to the PC card slot and lift out
the system as shown above.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
MODEM BOARD REMOVAL
Modem harness
M2.5x4
black
screws
M2.5x4 black
screws
Modem
board
1. Remove four M2.5x4 black screws securing the
CD-R/W/DVD-ROM bracket.
2. Remove the bracket.
3. Turn the system board upside down and disconnect
modem harness from the modem board.
4. Remove two M2.5x4 black screws securing the
modem board.
5. Disconnect the modem board from JP21 on the
system board.
COOLING MODULE REMOVAL
Fan harness
JP17
M2.5x4 black screws
M2x4 silver screws
Thermal upport
Fan
1. Remove three M2x4 silver screws securing the Fan.
2. Remove four M2.5x4 black screws securing the thermal
plate and the thermal support.
4. Disconnect the FAN harness from JP17.
5. Lift out the Fan and the thermal support.
3. Turn the system board upside down with your hand
supporting both the FAN and the thermal support
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
LED BOARD REMOVAL
JP1
LED board
assy
LED board
interface
cable
LED board support plate
M2x3 black screws
LED board
M2.5x4 black screws
1. Disconnect the LED board interface cable from JP1
on the LED board.
2. Remove six M2.5x4 black screws securing the
LED board assembly.
3. Lift out the LED board assembly.
4. Remove two M2x3 black screws securing the
LED board support plate and separate the
plate from the LED board.
TOUCHPAD BOARD REMOVAL
Touchpad cable
LED board
cable
JP3
Interface
board
FDD interface
cable
JP5
Touchpad
interface cable
Touchpad cable
Touchpad board
Touchpad bracket
JP4
1. Disconnect the LED board cable from JP3, FDD interface
cable from JP1, touchpad interface cable from JP5, and
the touchpad cable from JP4 on the interface board.
2. Remove three M2.5x4 black screws securing the
interface board.
4. Disconnect the touchpad cable from the touchpad
board
5. Slide the touchpad bracket to the direction of the
arrow and lift it out.
6. Lift out the touchpad board.
3. Lift out the interface board.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
SPEAKERS REMOVAL
Left/Right speaker
Left and Right speakers
Left and Right speaker cable
Tape
2. Peel off the tape securing the left and right speaker
cable.
3. Lift out the left and right speaker cable and remove
both speakers.
M2.5x4 black screws
1. Remove two M2.5x4 black screws securing the left and
right speakers.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
1900 Series
TM
15” DISPLAY MASK REMOVAL
FL INVERTER AND 15” LCD REMOVAL
LCD module
Latch
Display
mask
M2x3
black
screws
M2x3
black
screws
LCD
LCD/FL
harness
cover
FL cable
FL inverter board
LCD/FL cable
M2x5 silver screw
Mask seals
1. Remove two M2x5 silver screw securing the
FL inverter board.
2. Carefully lift up the FL inverter board and
disconnect the LCD/FL cable from CN1 and the
FL cable from CN2.
1. Slide the LCD/FL harness cover to the left and lift it out.
2. Remove two mask seals at the bottom corners of the
display assembly using a pair of fine-tipped tweezers.
2. Remove two M2.5x7 flat head black screws securing
the display mask.
3. Remove four M2X3 black screws securing the
LCD module.
5. Carefully rotate out the top of the LCD module
enough to access the display cable
6. Peel off the tape securing the LCD/FL cable and
disconnect the cable.
3. There are 23 latches securing the display mask.
Carefully insert your fingers between the mask and the
LCD panel and pry open the latches starting from the
bottom six latches, to the five latches on the right
and left sides, ending with the six top latches.
6. Remove eight M2x3 black screws securing the left
and right LCD brackets and separate the brackets.
Tough Enough for Today’s World
Download from Www.Somanuals.com. All Manuals Search And Download.
|