Download from Www.Somanuals.com. All Manuals Search And Download.
13. Do not use the telephone in the vicinity of a gas leak.
CAUTION:TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS BY THE BATTERY,
READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the appropriate type and size battery pack specified in the instruction manual
provided for this product.
2. Do not dispose of the battery pack in a fire. The cell may explode. Check with State and
local codes for possible special disposal instructions.
3. Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if swallowed.
4. Exercise care in handling the battery in order not to short it with conducting materials such
as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.
5. Charge the battery pack provided with or identified for use with this product only in accordance
with the instructions and limitations specified in the instruction manual provided for this
product.
6. Observe proper polarity orientation between the battery pack and the battery charger.
ATTENTION: THE PRODUCT THAT YOU HAVE PURCHASED CONTAINS
A
RECHARGEABLE BATTERY. UNDER VARIOUS STATE AND LOCAL LAWS, IT MAY BE
ILLEGALTO DISPOSE OF THIS BATTERY INTO THE MUNICIPAL WASTE STREAM. PLEASE
CHECK WITH YOUR LOCAL GOVERNMENT FOR DETAILS IN YOURAREAFOR RECYCLING
OPTIONS OR PROPER DISPOSAL.
SAVE THESE INSTRUCTIONS
TO HELP PROTECT THE ENVIRONMENT, THIS PRODUCT MAY CONTAIN RECYCLED OR
RECONDITIONED PARTS AND MATERIALS.
The RBRCTM Seal
The RBRCTM Seal on the (easily removable) nickel-cadmium battery
(contained in our product) indicates that Toshiba America Consumer
Products, Inc. (TACP) is voluntarily participating in an industry program
to collect and recycle these batteries at the end of their useful lives,
when taken out of service within the United States. The RBRCTM program
provides a convenient alternative to placing used nickel-cadmium
batteries into the trash or municipal waste, which is illegal in some areas.
TACP’s payments to RBRCTM make it easy for you to drop off the spent battery at local retailers
of replacement nickel-cadmium batteries, or at authorized TACP product service centers. You
may also contact your local recycling center for information on where to return the spent battery.
Please call 1-800-8-BATTER for information on Ni-Cd battery recycling in your area. TACP’s
involvement in this program is part of its commitment to protecting our environment and conserving
natural resources.
RBRCTM is a trademark of Rechargeable Battery Recycling Corporation.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE REQUIREMENTS
If the cordless telephone should malfunction, or need changes or modifications, all repairs will
be performed by an authorized Toshiba Service Station. This unit has been registered with the
FCC for direct connection to the telephone network. Under the FCC program, no customer is
authorized to repair this unit. This applies to a unit both in and out of warranty. If an unauthorized
repair is performed, the registration of the unit for direct connection to the network will be null
and void. If the unit is still in warranty, the remainder of the warranty period will also be null and
void.
It is the responsibility of users requiring service to report the need for service to their Toshiba
dealer.
IMP ORTANT INSTRUCTIONS TO USERS
Your SG-1700 has been designed and constructed to conform to federal regulations and can be
connected to the phone line as described in this manual.
Please note that each product connected to the telephone line places a certain load on the line.
We designate this as the unit’s “Ringer Equivalence Number.”
It is most unlikely, but . . . If your SG-1700 should cause problems on the phone line, the phone
company has the right to temporarily discontinue your service. If this happens, the phone company
will notify you and give you the opportunity to correct the problem. Also, you need to know that
the phone company does have the right to make changes in their lines and/or equipment.
If these changes might affect your SG-1700 (or require changes in the SG-1700 or its connection),
the phone company will notify you in writing, so you will have the chance to take whatever action
is necessary to ensure uninterrupted phone service.
F CC REQUIREMENTS
You are no longer required by the FCC to notify your local telephone company of your intent to
connect a new telephone. Your local telephone company may call you and request information
about your phone such as: the brand name, model number, registration number, and ringer
equivalence number. This information is provided on a label located at the bottom of the base
unit and handset.
You may not directly connect your SG-1700 to coin telephone services. Check with your local
telephone company if you wish to connect your SG-1700 to a party line service. Some party line
services require a special adaptor or modification to your telephone.
Finally, it should be noted that some cordless telephones operate at frequencies that may cause
interference to nearby TVs and VCRs; to minimize or prevent such interference, the base of the
cordless telephone should not be placed near or on top of a TV or VCR; and, if interference is
experienced, moving the cordless telephone farther away from the TV or VCR will often reduce
or eliminate the interference.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Toshiba America Consumer Products, Inc. takes pride in presenting
the SG-1700, one of the finest digital spread spectrum cordless
telephones available. Intelligent design, superb craftsmanship, and the
latest technological advances have been combined to provide you with
a telephone that is easy to operate and will provide you with years of
dependable service. Please take the time now to read your Owner’s
Manual carefully, so that you may enjoy the many convenient features
of your SG-1700 telephone.
FEATURES
• 2.4GHz Digital Spread Spectrum Transmission with Extended Talk
Range
• 30-Channel Auto Scanning
• Digital Call Protect Privacy Scrambling and Digital Security Code
• Volume Control (4 level)
• Ringer Volume and Tone Control
• 10 Speed Dial (20 digits)
• Long Standby Battery Life (7 days)
• One Way Page/Handset Locator
• Last Number Redial (32 digits)
• Mute on Handset
• Any-key Answer
• Reversible Charging System
• Hearing Aid Compatible/HAC Volume
• Desk/Wall Mountable (Bracket included)
• Headset Jack
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
1. SETTING UP THE BASE UNIT
For use on a desk or counter top follow the instructions below.
DESKTOP MOUNTING:
Snap the bracket's tab into the
notches on the base.
Fasten the AC adaptor
cord to prevent it from
being disconnected.
Raise the
antenna
to vertical
position.
Telephone Line Cord
Single-Line
Telephone Jack
(RJ11C)
Power Outlet
(AC 120V, 60Hz)
AC Adaptor
• USE ONLY WITH Supplied AC ADAPTOR (TAC-1700; power source
AC 120V, 60Hz/DC 9V).
• The AC adaptor must remain connected at all times. (It is normal for
the adaptor to feel warm during use.)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. CHARGE THE BATTERY PACK
Note
Use only the supplied battery pack (TRB-8000; power source
600 mAh, 3.6V).
Black
Red
q Remove the battery compartment cover
on the back of the handset by sliding it
down.
w Plug the battery pack cord into the
connector in the battery compartment in
correct polarity. It fits in only one way.
e Place the battery pack in the battery
compartment.
r Put the battery compartment cover back
by sliding until it snaps into place. Make
sure not to get the wires of the battery pack
caught in the cover.
t Place the handset on the base unit.
Be sure the IN USE/CHARGE LED lights.
If the IN USE/CHARGE LED does not
light, make sure theAC adaptor is plugged
in securely and that the electrical outlet is
working and not controlled by a light
switch.
It is important to charge the battery for
12 to 16 hours continuously without
any interruption before you use the
handset for the first time.
IN USE/
CHARGE
LED
Charging contacts
Note
The battery pack is not charged properly if the charging contacts are dirty or tarnished. Clean the
contacts occasionally with a dry cloth.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
After the battery pack is fully charged;
Operation
Approx. battery life
up to 6 hours
While in use (Talk mode)
While not in use (Standby mode)
up to 7 days
When TALK/BATT LOW LED blinks, all handset buttons are disabled
and the battery needs to be charged. If you are during a call, you hear
short beeps. Finish the call as soon as possible and place the handset
on the base unit.
Note
If a call comes in when the battery is too low to operate properly, you will be unable to answer the
call or the call will be disconnected.
WALL MOUNTING
MOUNTING ON A STANDARD WALL PLATE
Insert the bracket's tab into the
base's lower tab slots, then press
down on the top of the bracket to
snap it into the clip slots.
Flip the switch hook
tab over so the tab
holds the handset.
Raise the antenna.
Single-Line
Telephone Jack
(RJ11C)
Telephone
Line Cord
Power Outlet
(AC 120V, 60Hz)
AAdr
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• Route the cords through the guides.
• Place the base unit on the posts of the wall plate and push down until
it is firmly seated.
• USE ONLY WITH Supplied AC ADAPTOR (TAC-1700; power source
AC 120V, 60Hz/DC 9V).
Notes
•
•
Do not use any outlet controlled by a wall switch.
If you don’t have a standard wall plate, cut out the template below and use it to position two
screws (minimum length of 1-3/8 inches) into the wall with the heads protruding about 3/16 inch.
CUT
CUT
Wall mount template
IMPORTANT:
• Before mounting, select a wall area of sufficient
strength. If mounting on wallboard or in an area
of questionable strength, locate a stud for
maximum support of your telephone.
• Avoid electrical cables, pipes, or other items
behind the mounting location that could cause a
hazard.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATIONS OF CONTROLS
HANDSET CONTROLS
Antenna
Speed Dial Index Card (back)
Write down numbers stored in
memory.
TALK/BATT LOW LED
(Volume/Ringer) button
VOL
button
button
REDIAL
FLASH
(Memory) button
MEM
button
TALK
Dialpad
Rechargeable
Battery Pack (back)
button
button
TONE
button
MUTE
PAUSE
button
CHANNEL
Charging Contacts
BASE UNIT CONTROLS
DC IN 9V jack
LINE Modular jack
T-P (Tone-Pulse)
Switch
IN USE/CHARGE LED
button
PAGE
Antenna
Charging Contacts
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Please see “LOCATION OF CONTROLS” for the location of
each button used for the following operations.
TONE/P ULSE SETTING
Set the TONE/PULSE switch on the back of the base unit to TONE and
make a trial call.
If the call does not connect, set the TONE/PULSE to PULSE.
MAKING A CALL
1. MAKING A CALL
TALK
q Press
.
w Listen for the dialtone.
e Key in the phone number you are calling.
1, 4
3
TALK
r To hang up, press
again or place the
handset on the base unit. The TALK/BATT
LOW LED turns off.
2. ANSWERING A CALL
q Simply pick up the handset or press any key if
the handset is located away from the base unit.
The TALK/BATT LOW LED will light.
TALK
w To hang up, press
or place the handset
1, 2
on the base unit.
The TALK/BATT LOW LED turns off.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. INTERFERENCE OR STATIC
CHANNEL
If you hear noise during a call, press
to select another channel.
The TALK/BATT LOW LED blinks during changing a channel.
4. CHANGING THE RINGER VOLUME
Press
/
to select one of four ringer tone and volume combinations
during standby mode.
Each time you press
/
, the setting will change.
5. CHANGING THE HANDSET SPEAKER VOLUME
During a telephone call, press
/
to select one of four speaker volume
levels; Loud, High, Medium and Low,
The setting will remain in effect even after you hang up the current call.
Note
The Loud setting may be too loud because it is set for hearing aid compatibility.
6. REDIALING
TALK
REDIAL
Press
and then press
. The last number called (up to 32
digits) will then be dialed again.
7. USING THE CALL WAITING SERVICE, ETC.
To use this feature, you must subscribe to the Call Waiting service.
When you hear a call-waiting tone while you are already talking on the
FLASH
phone, simply press
.
FLASH
To take the original call back, press
again.
Note
Pressing
FLASH
without receiving a Call Waiting signal may disconnect the current caller.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
8. SENDING TONE SIGNAL (for Pulse service user)
Even if you have Pulse service (the Tone-Pulse switch is set to Pulse).
You can use this phone with banking and other phone services requiring
touch tone signals.
q Dial the service number and wait for the connection.
TONE
w Press
then, enter the numbers required. You will hear the
tones on the line.
9. MUTING
MUTE
Press
to turn off the microphone during a conversation.
The TALK/BATT LOW LED blinks. You may speak to someone in the
room without the caller overhearing.
MUTE
To resume normal conversation, press
or TALK
.
10. PAGING
PAGE
To locate the handset (while it is off the base), press
on the base
PAGE
unit. The handset beeps for 30 seconds. To stop paging, press
or return the handset to the base unit.
Notes
•
•
You cannot page the handset during a call.
Be careful not to close your ear to the ringer on the back side of the handset while paging,
because it may be too loud.
11. OUT OF RANGE
During a call, as you begin to move too far from the base, you first hear
a clicking sound. As you travel farther, the noise increases. If you travel
out-of-range, your call terminates.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CARRYING THE HANDSET IN THE BELT CLIP
You can attach the Belt Clip to the handset in order to carry it on your
belt.
Attaching the Belt Clip to the Handset
Insert the Belt Clip tabs into the holes on each
side of the handset until they click.
Note
Be sure to insert the tab properly into each hole to prevent
the belt clip from falling off.
Removing the Belt Clip from the Handset
Pull both sides of the Belt Clip to release the tabs from the holes.
Note
Remove the Belt Clip carefully from the handset, taking care not to hurt your fingers or damage
your nails.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
USING A HEADSET
You can talk with hands-free convenience using an optional headset
(part #. RC008260) that has a 3/32-inch(2.5mm) plug.
To connect the headset, open the rubber
cover on the left side of the handset, then
insert the headset’s plug into the jack.
With a headset connected, you can make or
answer calls as usual using the keys on the
handset.
You can use the supplied Belt Clip to hang
the handset on your belt for greater
convenience.
When you finish using the headset,
disconnect it from the handset and close the
rubber cover to protect the jack.
Notes
•
•
•
The handset’s earspeaker and microphone are turned off with a headset connected.
Pressing the button of the handset also controls the connected headset’s volume.
If you place the handset on the base unit while the headset is connected, be sure the handset is
placed properly.
/
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMORY DIALING
You can store up to 10 telephone numbers in memory.
Notes
In memory dialing operation,
•
If more than 20 seconds elapse between pressing buttons, the operation will be cancelled and
you must start over again.
•
•
If you press a wrong button, an error tone sounds and the handset returns to standby mode.
If a call comes in, the operation will be canceled and you will hear the ring.
1. STORING NUMBERS
You can store up to 20 digits including #, , TONE, and PAUSE in one
memory address.
TALK
q Pick up the handset from the base unit. (Do not press
.)
MEM
w Press
.
e Dial the telephone number you wish to store. (up to 20 digits).
MEM
r Press
.
t Enter the memory address (0 to 9) at which you wish to store the
phone number stored in step 3.
You will hear a long beep when the number is successfully stored.
To store more telephone numbers, repeat the steps from w to t.
y Return the handset to the base unit.
u Record the telephone numbers on the SPEED DIAL INDEX CARD,
and place it on the back of the handset.
EXAMPLE: To store 9012345 in memory address 3
WX 9
0
1
3
3
2
4
5
MEM
MEM
Replacing a telephone number
Just store the new number following the same steps in “1. STORING
NUMBERS.”
The new number will replace the previously stored one.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. DIALING A STORED NUMBER
TALK
q Pick up the handset and press
The TALK/BATT LOW LED lights.
MEM
.
w Press
.
e Enter the memory address (0 to 9).
The stored number will be dialed.
Note
If you enter a memory address which does not have any stored number, error beeps sound.
3. ERASING A STORED TELEPHONE NUMBER
TALK
q Pick up the handset. (Do not press the
button.)
MEM
w Press the
button twice.
e Enter the memory address button (0 to 9) you wish to erase.
When erasing is completed, you will hear a long beep.
4. INSERTING A PAUSE IN MEMORY
PAUSE
Use
to make an outgoing call through a PBX or long distance.
PAUSE
Each time you press
, a pause of about two seconds is inserted
during the dialing sequence. If more than two seconds are needed,
PAUSE
press
twice.
PAUSE
EXAMPLE: To store “0
1234567890” in memory address 4,
press:
WX 9
0
3
4
0
1
2
5
6
8
4
7
MEM
PAUSE
MEM
.5. CHAIN DIALING
Combining ordinary dialing and memory dialing, you can dial a long
telephone number with less steps.
EXAMPLE: Divide the number into two portions and store the first portion
in memory address 1 and the second portion in memory address 2.
When you call, press following buttons;
1
2
MEM
MEM
TALK
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
SUPPLIED ACCESSORIES
Rechargeable Battery pack (1) TRB-8000 Part #. RC004931
AC Adaptor
Telephone Cord
Belt Clip
Owner’s Manual
Speed Dial Index
Bracket
(1) TAC-1700 Part #. RC009258
(1) Part #. RC008231
(1) Part #. RC009263
(1) Part #. RC009259
(1) Part #. RC009264
(1) Part #. RC009262
OPTIONAL ACCESSORIES
Headset
(1) Part #. RC008260
For the purchase of Accessories, please call 1-877-644-7373.
TROUBLESHOOTING GUIDE
Should any problem occur with the set, make the following simple tests
to determine whether or not servicing is required.
PROBLEM
No dial tone.
SOLUTION
•The AC adaptor of the base unit is disconnected.
→Plug the AC adaptor into the base unit and the AC
120V outlet.
No calls come in.
•The battery is low.
→Place the handset on the base unit to recharge.
•Telephone line cord is disconnected.
→Check both ends of the telephone jack.
•The previous call was not disconnected.
TALK
→Press
to disconnect the line.
•Trouble with the telephone line.
→Check an extension line.
•Outlet used is controlled by a wall switch in its OFF
position.
→Relocate to another outlet.
•The digital security code is changed.
→Disconnect the power and remove the handset. After
a few seconds, restore the power and place the
handset on the base for at least 3 seconds.
•The handset is too far from the base unit.
→Bring the handset near the base unit.
•You press the button while the handset is on the base
unit’s charging cradle.
→Pick up the handset from the base unit before you
TALK
press
.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION
PROBLEM
Noise or
•The handset is too far from the base unit.
interference.
→Bring the handset near the base unit.
•The battery is low.
→Place the handset on the base unit to recharge.
•The base unit is located in a place with high
interference.
→Relocate to another outlet.
•Interference from TV, appliances, etc.
CHANNEL
→Press
to select a clearer channel, or relocate
the base unit.
•There may be line noise.
→Check with another telephone.
•The volume control is set too high.
→Reduce volume to lower setting.
•The base antenna is not in a vertical position.
→Lift the antenna to a vertical position.
Battery goes low
quickly.
•The battery was not fully charged at the initial charging.
→Charge the battery for 12 to 16 hours without any
interruption.
•The battery is several years old.
→Replace with a new battery.
•The battery is not installed correctly.
→Install the battery correctly.
The handset battery
does not charge.
•The charging contacts of the handset and base are not
clean.
→Clean them with a dry cloth.
•The battery is several years old.
→Replace with a new battery.
The unit operates
abnormally.
•The phone needs to be reset.
→Disconnect the AC adaptor and reconnect it after a
few seconds.
TALK/BATT LOW
LED blinks.
The operation is
stopped.
•The battery is low.
→Recharge the battery.
When the handset is
returned to the base
unit with the volume
level set at High, a
momentary squeal
or howling sound
may sometimes be
heard.
•This is normal.
→It may be prevented by changing the volume setting
to Medium or Low before returning the handset to the
base unit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY/SERVICE
TE LE P H ONE /TE LE P H ONE ANSWE R MACH INE LIMITE D WAR R ANTY
ToshibaAmerica Consumer Products.Inc(“TACP”) and Toshiba Hawaii,Inc.(“THI”) make the following limited warranties.
These limited warranties extend to the original consumer purchaser or any person receiving this set as a gift from the
original consumer purchaser and to no other purchaser or transferee.
Limited One(1) Year Warranty of Labor
and parts
TACP/THI warrant this product and its parts against defects
in materials or workmanship for a period of one(1) year
after the date of original retail purchase. During this period,
TACP/THI will repair or replace your defective product with
a new or refurbished unit at our option.
(3) Within the continental U.S.A., if you should find a
defective product within the warranty period please call 1-
877-644-7373.
(4) Warranties extend only to defects in materials or
workmanship as limited above and do not extend to any
product or parts which have been lost or discarded by you,
or to damage to products or parts caused by misuse, accident,
damage caused by Acts of God, such as lightning or
fluctuations in electric power, improper installation,
improper maintenance or use in violation of instructions
furnished by us; or to units which have been altered or
modified without authorization of TACP/THI, or to damage
to products or parts thereof which have had the serial number
removed, altered, defaced or rendered illegible.
(5) Physically damaged products are not acceptable for
repair or exchange within or after the warranty period
expires.
Owner’s Manual
You should read the owner’s manual thoroughly before
operating this product.
Your Responsibility
The above warranties are subject to the following conditions.
(1) You must provide a copy of your bill of sale or other
proof of purchase.
(2) These warranties are effective only if the product is
purchased and operated within the USA or Puerto Rico.
How to Obtain Warranty Service
In the event a problem should develop with your product, please proceed as follows;
In Hawaii contact:
Toshiba Hawaii, Inc.
327 Kamakee Street,
Honolulu, HI 96814
(808)-591-8377
In The Continental United States contact:
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose,
are expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied
by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements
and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall
TACP/THI be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in
any manner whatsoever. The time within which an action must be commenced to enforce any obligation of TACP/THI
arising under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to
ninety(90) days from the date you discover, or should have dicovered, the defect. This limitation does not apply to implied
warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some
states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or
limitation of incidental or consequential damages, so the above provisions may not apply to you.
© 2000 TOSHIBAAMERICA CONSUMER PRODUCTS. INC.
UCZZ01700BZ RC009259
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|