CareLine™
User’s manual
SN6107
DECT 6.0 accessory handset
for use with VTech models
SN1157/SN1196/SN1197/SN6127/
SN6146/SN6147/SN6187/SN6196/
SN6197
Congratulations
on purchasing your new VTech product. Before using this
telephone, please read Important safety instructions on
page 9 of this manual.
This manual has instructions on how to set up and register
your new handset. For complete instructions on using the
handset, see the Abridged user’s manual that came with
your telephone base.
You may also view or download the online
Complete user’s manual for a full set of installation
In Canada, visit www.vtechcanada.com.
Compatible with
Hearing Aid T-Coil
Telephones identified with this logo have reduced
noise and interference when used with most T-coil
equipped hearing aids and cochlear implants.
The TIA-ꢀ083 Compliant Logo is a trademark of
the Telecommunications Industry Association.
Used under license.
T
TIA-1083
®
The ENERGY STAR program (www.energystar.gov)
recognizes and encourages the use of products
that save energy and help protect our environment.
We are proud to mark this product with the
®
ENERGY STAR label indicating it meets the latest
energy efficiency guidelines.
Register online to get an additional 3-month warranty!
Registration
Register your product online for enhanced warranty
support.
Product news
Learn about the latest VTech products.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset charger installation
ꢀ. Install the charger
as below.
ꢁ. Place the handset in
the handset charger
to charge.
Electrical outlet
not controlled by
a wall switch
Handset charger
power adapter
Handset battery charging
Once you have installed the battery, the handset indicates
the battery status. If necessary, place the handset in the
handset charger to charge. The battery is fully charged
after ꢀꢀ hours of continuous charging.
Battery indicators
Battery status
Action
The screen is blank, The battery has no
Charge without
or displays Place
in charger and
flashes.
or very little charge.
The handset cannot 30 minutes).
be used.
interruption (about
The screen displays The battery has
Charge without
Low battery and
flashes.
enough charge to be interruption (about
used for a short time. 30 minutes).
The screen displays The battery is
HANDSET X. charged.
To keep the
battery charged,
place it in the
handset charger
when not in use.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Add and register a handset
You can add new handsets to your telephone system. Each
handset must be registered with the telephone base before
use. When first purchased, each expansion handset shows
To register HS, see manual. The new handset should be
charged without interruption for at least 30 minutes before
registering it to the telephone base.
Make sure the handset is out of the handset charger and is
put near the telephone base. Make sure the handset shows
To register HS, see manual before you begin registration.
To register a handset to your SN1157/SN1196/SN1197/
SN6146/SN6147/SN6196/SN6197 telephone base:
ꢀ. Press MENU on the telephone base
when idle.
ꢁ. Scroll to Settings, then press SELECT.
3. Scroll to Registration, then press
SELECT. The telephone base shows
Registering... Please wait.
ꢂ. Press QUIET on the cordless
#
handset. The handset shows
Registering... Please wait. Then
HANDSET X Registered appears on
the cordless handset and the telephone
base, and both devices beep. The handset is now
registered with the telephone base. It takes up to
60 seconds to complete registration.
If registration fails, the telephone base displays
Registration failed and you hear an error tone.
Start again from Step ꢀ above.
To register a handset to your SN6127/SN6187
telephone base:
• Put the handset into the telephone
base. The base IN USE light turns
solid red. The handset shows
Registering... Please wait. Then
HANDSET X Registered appears on
the cordless handset. The handset
beeps and is now registered with
the telephone base. It takes up to
60 seconds to complete registration.
If registration fails, the handset displays Registration failed
and you hear an error tone. Start again from Step ꢀ above.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Deregister devices
If you want to replace a device, or reassign the designated
device number of a registered device, you must deregister
all devices that are registered to the telephone base. Then
register each device individually.
To deregister all devices from your SN1157/
SN1196/SN1197/SN6146/SN6147/SN6196/SN6197
telephone base:
ꢀ. Press and hold FIND HS at the side of the telephone
base for about ꢀ0 seconds until the telephone base
shows Registering... Please wait followed by
Deregister all devices?, then release FIND HS.
ꢁ. Immediately press YES or FIND HS.
3. All handsets show To register HS, see manual. The
deregistration process takes about ꢀ0 seconds to complete.
To deregister all devices from your SN6127/SN6187
telephone base:
ꢀ. Press and hold /FIND HANDSET at the side of the
telephone base for about ꢀ0 seconds until the telephone
base IN USE light turns solid red and then flashes red,
then release /FIND HANDSET.
ꢁ. Immediately press /FIND HANDSET.
3. All handsets show To register HS, see manual. The
deregistration process takes about ꢀ0 seconds to complete.
You cannot deregister all devices if any system device is
in use.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset overview
REDIAL/PAUSE
• Press repeatedly to view the last ꢀ0
numbers dialed.
• Press and hold to insert a dialing pause
while dialing or entering numbers.
Incoming call light
• Flashes when there is an incoming call/
the base is paging the handset.
/
• Review the phonebook when idle.
• Scroll up while in menus or lists.
• Move the cursor to the right while
entering names or numbers.
MENU/SELECT
• Show the menu.
• Select an item or save an entry/setting
while in a menu.
/FLASH
• Make or answer a call.
• Answer an incoming call when you receive
a call waiting alert during a call.
1
• Press repeatedly to add or remove ꢀ in
front of the telephone number before
dialing or saving it in the phonebook
while reviewing a caller ID log entry.
• Press and hold to set or dial your
voicemail number.
QUIET
#
• Press repeatedly to display other dialing
options when reviewing a caller ID log
entry.
• Press and hold to set and turn on the
quiet mode, or turn it off.
• Silence the handset ringer temporarily
while the phone is ringing.
• Switch to tone dialing during a call if you
have pulse service.
• Switch between upper case and lower
case while entering characters.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset overview
CHARGE light
• On when the handset is charging.
CID/
• Review the caller ID log when idle.
• Scroll down while in menus or lists.
• Move the cursor to the left while
entering names or numbers.
/CANCEL
• Hang up during a call.
• Cancel an operation, or back up to the
previous menu while in a menu.
• Press and hold to return to idle mode
while in a menu.
• Silence the handset ringer temporarily
while the phone is ringing.
• Press and hold to erase the missed call
indicator when idle.
+
VOL- and VOL
• Adjust the listening volume during a call
or message playback.
• Adjust the handset ringer volume while
idle.
Dialing keys
• Enter numbers or characters.
• Answer an incoming call.
AUDIO ASSIST
• Enhance the clarity and loudness of the
caller’s voice during a call.
MUTE/DELETE
• Mute the microphone during a call.
• Silence the handset ringer temporarily
while the phone is ringing.
• Delete an individual entry while
reviewing the redial list/phonebook/
caller ID log/reminder.
• Delete a character or digit while entering
names or numbers.
• Delete the playing message/
announcement.
• Make or answer a call.
• Switch between the handset
speakerphone and the handset
earpiece during a call.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset battery
It takes up to ꢀꢀ hours for the battery to be fully charged.
When it is fully charged, you can expect the following
performance:
Operation
Operating time
While in handset use (talking*)
Up to seven hours
While in speakerphone mode (talking*) Up to five hours
While not in use (standby**) Up to seven days
* Operating times vary depending on your actual use and the age
of the battery.
** Handset is not charging or in use.
The battery needs charging when:
• A new battery is installed in the handset.
• The handset beeps.
• A battery is properly installed and the screen is blank.
• Low battery or Place in charger displays on the cordless
handset screen.
CAUTION:
To reduce the risk of fire or injury, read and follow these
instructions:
• Use only the batteries provided or equivalent. To order a
or dial 1 (800) 267-7377.
• Do not dispose of the batteries in a fire. Check with local
waste management codes for special disposal instructions.
• Do not open or mutilate the batteries. Released electrolyte is
corrosive and may cause burns or injury to the eyes or skin.
The electrolyte may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a
short circuit with conductive materials.
• Charge the batteries provided with or identified for use with
this product only in accordance with the instructions and
limitations specified in this manual.
• Observe proper polarity orientation between the battery and
metallic contacts.
• To prevent fire or shock hazard, do not expose this product to
water or any type of moisture.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury, including the following:
ꢀ. Read and understand all instructions.
ꢁ. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
ꢂ. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink,
laundry tub or swimming pool, or in a wet basement or shower.
ꢃ. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Slots and openings in the back or bottom of the telephone base, handset and pendant
are provided for ventilation. To protect them from overheating, these openings must
not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This
product should never be placed near or over a radiator or heat register. This product
should not be placed in any area where proper ventilation is not provided.
ꢄ. This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply in your home or office,
consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product where the
cord may be walked on.
9. Never push objects of any kind into this product through the slots in the telephone
base or handset because they may touch dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the product.
ꢀ0. To reduce the risk of electric shock, do not disassemble this product, but take it to
an authorized service facility. Opening or removing parts of the telephone base or
handset other than specified access doors may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause electric shock when the product is
subsequently used.
ꢀꢀ. Do not overload wall outlets and extension cords.
ꢀꢁ. Unplug this product from the wall outlet and refer servicing to an authorized service
facility under the following conditions:
• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled onto the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operation instructions. Improper
adjustment of other controls may result in damage and often requires extensive work
by an authorized technician to restore the product to normal operation.
• If the product has been dropped and the telephone base/handset/pendant has
been damaged.
• If the product exhibits a distinct change in performance.
ꢀ3. Avoid using a telephone (other than cordless) during an electrical storm. There is a
remote risk of electric shock from lightning.
ꢀꢂ. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain
circumstances, a spark may be created when the adapter is plugged into the power
outlet, or when the handset or pendant is replaced in its cradle. This is a common
event associated with the closing of any electrical circuit. The user should not plug the
phone into a power outlet, and should not put a charged handset into its cradle, if the
phone is located in an environment containing concentrations of flammable or flame-
supporting gases, unless there is adequate ventilation. A spark in such an environment
could create a fire or explosion. Such environments might include: medical use of
oxygen without adequate ventilation; industrial gases (cleaning solvents; gasoline
vapors; etc.); a leak of natural gas; etc.
ꢀꢃ. Only put the handset of your telephone next to your ear when it is in normal talk mode.
ꢀ6. The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
SAVE THESE INSTRUCTIONS
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a
multidisciplinary evaluation of the interference between portable wireless telephones and
implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration,
WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches from the pacemaker.
• Should NOT place wireless telephones directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to by standers with pacemakers from other
persons using wireless telephones.
Operating range
This cordless telephone operates with the maximum power allowed by the Federal
Communications Commission (FCC). Even so, this handset and telephone base can
communicate over only a certain distance - which can vary with the locations of the
telephone base and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset displays Out of range OR Base no power.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call
may not connect well when you press . Move closer to the telephone base, then press
to answer the call.
If the handset moves out of range during a telephone conversation, there may be
interference. To improve reception, move closer to the telephone base.
ECO mode
This power conserving technology reduces power consumption for optimal battery
performance. The ECO mode activates automatically whenever the handset is
synchronized with the telephone base.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated
with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your
telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the
rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub
or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment.
For your own safety, take caution when using electrical appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years.
Clean it only with a soft cloth slightly dampened with water or mild soap. Do not use
excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you
are wet or standing in water. If the telephone base should fall into water, DO NOT
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE
CORD FROM THE WALL. Then remove the telephone by the unplugged cords.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
About cordless telephones
• Privacy: The same features that make a cordless telephone convenient create some
limitations. Telephone calls are transmitted between the telephone base and the
cordless handset by radio waves, so there is a possibility that the cordless telephone
conversations could be intercepted by radio receiving equipment within range of
the cordless handset. For this reason, you should not think of cordless telephone
conversations as being as private as those on corded telephones.
• Electrical power: The telephone base of this cordless telephone must be connected
to a working electrical outlet. The electrical outlet should not be controlled by a wall
switch. Calls cannot be made from the cordless handset if the telephone base is
unplugged, switched off or if the electrical power is interrupted.
• Potential TV interference: Some cordless telephones operate at frequencies
that may cause interference to televisions and VCRs. To minimize or prevent such
interference, do not place the telephone base of the cordless telephone near or on
top of a TV or VCR. If interference is experienced, moving the cordless telephone
farther away from the TV or VCR often reduces or eliminates the interference.
• Rechargeable batteries: Exercise care in handling batteries in order not to create a
short circuit with conducting material such as rings, bracelets and keys. The battery
or conductor may overheat and cause harm. Observe proper polarity between the
battery and the battery charger.
• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a
safe manner. Do not burn or puncture the battery. Like other batteries of this type, if
burned or punctured, they could release caustic material which could cause injury.
The RBRC® seal
The RBRC® seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to collect and
recycle these batteries at the end of their useful lives, when taken out of service within
the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-metal
hydride batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at
local retailers participating in the RBRC® program or at authorized VTech product service
centers. Please call 1 (800) 8 BATTERYTM for information on Ni-MH battery recycling and
disposal bans/restrictions in your area. VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories provided in the sales package
(“Product”) are free from defects in material and workmanship, pursuant to the following
terms and conditions, when installed and used normally and in accordance with the
Product operating instructions. This limited warranty extends only to the Consumer for
Products purchased and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and
workmanship during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair
or replace at VTech’s option, without charge, a Materially Defective Product. If we repair
the Product, we may use new or refurbished replacement parts. If we choose to replace
the Product, we may replace it with a new or refurbished Product of the same or similar
design. We will retain defective parts, modules, or equipment. Repair or replacement of
the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired
or replacement Products to you in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (ꢀ) YEAR from the date of
purchase. If VTech repairs or replaces a Materially Defective Product under the terms
of this limited warranty, this limited warranty also applies to the repaired or replacement
Product for a period of either (a) 90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining on the original one-year warranty;
whichever is longer.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
What is not covered by this limited warranty?
This limited warranty does not cover:
ꢀ. Product that has been subjected to misuse, accident, shipping or other physical
damage, improper installation, abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone
other than an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems; or
ꢂ. Product to the extent that the problem is caused by use with non-VTech accessories; or
ꢃ. Product whose warranty/quality stickers, product serial number plates or electronic
serial numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United
States of America or Canada, or used for commercial or institutional purposes
(including but not limited to Products used for rental purposes); or
ꢄ. Product returned without a valid proof of purchase (see item ꢁ below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or
outside the unit.
repair of systems
How do you get warranty service?
NOTE: Before calling for service, please review the user’s manual - a check of the
Product’s controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during
transit and transportation and are responsible for delivery or handling charges incurred
in the transport of the Product(s) to the service location. VTech will return repaired
or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit.
If the Product failure is not covered by this limited warranty, or proof of purchase does
not meet the terms of this limited warranty, VTech will notify you and will request that you
authorize the cost of repair prior to any further repair activity. You must pay for the cost
of repair and return shipping costs for the repair of Products that are not covered by this
limited warranty.
What must you return with the Product to get warranty service?
ꢀ. Return the entire original package and contents including the Product to the VTech
service location along with a description of the malfunction or difficulty; and
ꢁ. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased
(Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It
supersedes all other written or oral communications related to this Product. VTech
provides no other warranties for this Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There are no other express warranties.
No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/provinces do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special, incidental, consequential, or similar
damages (including, but not limited to lost profits or revenue, inability to use the Product
or other associated equipment, the cost of substitute equipment, and claims by third
parties) resulting from the use of this Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a
Class B digital device under Part ꢀꢃ of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part ꢀꢃ of the FCC rules. Operation is subject to the following
two conditions: (ꢀ) this device may not cause harmful interference, and (ꢁ) this device
must accept any interference received, including interference that may cause undesired
operation. Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to
the intended usage of the product. This product has been tested and found to comply
with the FCC criteria. The handset may be safely held against the ear of the user. The
telephone base shall be installed and used such that parts of the user’s body other than
the hands are maintained at a distance of approximately ꢁ0 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements
adopted by the Administrative Council for Terminal Attachments (ACTA). The label on
the back or bottom of this equipment contains, among other things, a product identifier
in the format US:AAAEQ##TXXXX. This identifier must be provided to your telephone
service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone
network must comply with applicable Part 68 rules and technical requirements adopted
by ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. An RJꢀꢀ
jack should normally be used for connecting to a single line and an RJꢀꢂ jack for two
lines. See the installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you
may connect to your telephone line and still have them ring when you are called. The
REN for this product is encoded as the 6th and ꢄth characters following the US: in the
product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum
of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm
dialing equipment connected to your telephone line, ensure the connection of this
equipment does not disable your alarm equipment. If you have questions about what will
disable alarm equipment, consult your telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the
problem has been corrected. Repairs to this telephone equipment can only be made by
the manufacturer or its authorized agents. For repair procedures, follow the instructions
outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider
may temporarily discontinue your telephone service. The telephone service provider
is required to notify you before interrupting service. If advance notice is not practical,
you will be notified as soon as possible. You will be given the opportunity to correct the
problem and the telephone service provider is required to inform you of your right to file a
complaint with the FCC. Your telephone service provider may make changes in its facilities,
equipment, operation, or procedures that could affect the proper functioning of this product.
The telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency
telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test
emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Industry Canada
Operation is subject to the following two conditions: (ꢀ) this device may not cause harmful
interference, and (ꢁ) this device must accept any interference, including interference that
may cause undesired operation.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry
Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is ꢀ.0. The REN is
an indication of the maximum number of devices allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the RENs of all the devices does not
exceed five.
This product meets the applicable Industry Canada technical specifications.
Technical specifications
Frequency control
Transmit frequency
Channels
Crystal controlled PLL synthesizer
ꢀ9ꢁꢀ.ꢃ36-ꢀ9ꢁ8.ꢂꢂ8 MHz
ꢃ
Nominal effective range Maximum power allowed by FCC and IC. Actual operating
range may vary according to environmental conditions at the
time of use.
Power requirements
Handset: ꢁ.ꢂV Ni-MH
Charger: 6V AC @ 300mA
Memory
Handset directory:
ꢃ0 memory locations; up to 30 digits and ꢀꢃ characters
Handset caller ID log:
ꢃ0 memory locations; up to ꢁꢂ digits and ꢀꢃ characters
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 9ꢄ008.
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W ꢀLꢃ.
VTech is the registered trademark of VTech Holdings Limited.
Copyright © ꢁ0ꢀ3 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
9ꢀ-006ꢁ98-0ꢁ0-ꢀ00
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
|