Color Television
36A61
Owner’s Manual
©
© 2001 TOSHIBA CORPORATION
All Rights Reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
A polarized alternating current line plug — having one blade wider
than the other. This plug will fit into the power outlet only one way. If
you are unable to insert the plug into the outlet, try reversing the plug.
A product and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the product
and cart combination to overturn.
Un enchufe de línea de corriente alterna polarizado — posee una
cuchilla más ancha que la otra. Este enchufe entrará en la toma de la
red de una sola forma. Si no puede inertar el enchufe en la toma de la
red, trate de invertirlo.
La combinación de un producto y
un carrito deberá moverse con
cuidado. Las paradas repentinas,
la fuerza excesiva, y las superficies
desiguales pondrían hacer que
volcase la combinación del carrito
y del producto.
Alternate Warnings — A three-wire grounding-type plug — a plug
having a third (grounding) pin. This plug will only fit into grounding-
type power outlet.
Advertencias alternativas — Enchufe de tippo puesta a tierra de tres
conductores — enchufe que posee un tercer terminal (de puesta a
tierra). Este enchufe solamente encajará en una toma de la red de tipo
puesta a tierra.
USE / UTILIZACIÓN
Overloading — Do not overload wall outlets, extension cords or
convenience receptacles beyond their capacity, since this can result in
fire or electric shock.
Water and Moisture — Do not use the TV set near water — for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
Sobrecarga — No sobrecargue las tomas de la red, los cables
prolongadores, ni los adaptadores para múltiples tomas, ya que esto
supondría el riesgo de incendios o de descargas eléctricas.
Agua y humedad — No utilice el televisor cerca del agua — por
ejemplo, cerca de una bañera, un lavabo, un fregadero, una lavadora, en
un sótano húmedo, cerca de una piscina, ni lugares por el estilo.
During lightning storms, or when the TV set will be left unattended
and unused for a long period of time, unplug the power cord from the
wall outlet and disconnect the antenna or cable system. This will
prevent damage to the TV set due to lightning and power-line surges.
Ventilation — The slots and openings in the cabinet and in the back or
bottom are provided for necessary ventilation. Never block or cover
these slots and openings to ensure reliable operation of the TV set and
to protect it from overheating.
Durante tormentas eléctricas, o cuando no vaya a utilizar el televisor
durante mucho tiempo, desenchufe el cable de alimentación de la toma
de la red y desconecte la antena o el sistema de cablevisión. Esto evitará
que se dañe el televisor debido a rayos y a sobretensiones repentinas en
la red.
Ventilación — Las ranuras y aberturas de la caja y de la parte posterior
o de la base son para proporcionar la ventilación necesaria. Para
asegurar la operación fiable del televisor para protegerlo contra el
recalentamiento. No bloquee ni cubra nunca estas ranuras y aberturas.
a. Never cover the slots and openings with a cloth or other materials.
a. No cubra nunca las ranuras ni las aberturas con paños ni otros
materiales.
b. Never block the slots and openings by placing the TV set on a bed,
sofa, rug or other similar surface.
Object and Liquid Entry — Never push objects of any kind into the
TV set through the cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the TV set.
Entrada de objetos y líquidos — No introduzca nunca objetos de
ningún tipo en este televisor a través de las aberturas, ya que podrían
tocar puntos de tensión peligrosa o cortocircuitar piezas, lo que podría
resultar en incendio o descarga eléctrica. No vierta nunca liquidos de
ningún tipo sobre este televisor.
b. No bloquee nunca las ranuras ni las aberturas colocando el televisor
sobre una cama, un sofá, una alfombra, ni demás superficies similares.
c. Never place the TV set in a confined space such as a bookcase, built-
in cabinet, or any other place of poor ventilation.
c. No coloque nunca el televisor en un espacio cubierto, como una
librería o un estante empotrados, nien un lugar de mala ventilación.
Cleaning — Unplug the TV set from the wall outlet before cleaning or
polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth
lightly dampened with water for cleaning the exterior of the TV set.
Heat — Do not place the TV set near or over a radiator or heat
register, or where it is exposed to direct sunlight.
Limpieza — Desenchufe el televisor de la toma de la red antes de
limpiarlo. No utilice limpiadores líquidos ni aerosoles. Para limpiar el
exterior del televisor, utilice un paño ligeramente humedecido en agua.
Calor — No coloque el televisor cerca ni sobre un radiador ni un
registro de calor, ni expuesto a la luz solar directa.
Power-Cord Protection — Do not allow anything to rest on or roll
over the power cord, and do not place the TV set where the power cord
is subject to wear or abuse.
Attachments — Never add accessories that have not been specifically
designed for the TV set. Never remodel the TV set by yourself as this
can result in a fire hazard or electric shock.
Protección del cable de alimentación — No coloque ni pase sobre el
cable de alimentación, ni coloque el telivisor donde su cable de
alimentación pueda sufir cualquier tipo de daños.
Aditamentos — No utilice aditamentos no recomendados por el
fabricante del televisor, ya que podrían suponer un peligro. No
remodele nunca el televisor usted mismo, ya que esto podría causar el
riesgo de incendios o descargas eléctricas.
Accessories — Do not place the TV set on an unstable cart, stand,
tripod, bracket, or table. The TV set may fall, causing serious injury to
a child or adult, and serious damage to the TV set. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or
sold with the TV set, and should use a mounting accessory recom-
mended by the manufacturer.
If a snapping or popping sound from a TV set is heard continuously or
frequently while the TV set is operated, unplug the TV set and consult
your dealer or service technician. It is normal for some TV sets to make
occasional snapping or popping sounds, particularly when being turned
on or off.
Accesorios — No coloque el televisor sobre un carrito, una base, un
trípode, un soporte ni una mesea inestable. El televisor podría caerse,
causando serios daños a niños o adultos, o al propio televisor. Utilice
solamente el carrito, la base, el trípode, el soporte, o la mesa que
recomiende el fabricante, o que se venda con el televisor, y utilice un
accesorio de montaje recomendado por el fabricante.
Si se oye un sonido seco de un televisor continuo o frecuente mientras
el televisor esté funcionando, desenchúfelo y consulte a su proveedor o
a un técnico de servicio. Es normal que algunos televisores produzcan
sonidos secos, particularmente cuando conecte o desconecte su
alimentación.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE / SERVICIO DE REPARACIÓN
When the TV set reaches the end of its useful life, improper disposal
could result in a picture tube implosion. Ask a qualified service
technician to dispose of the TV set.
Damage Requiring Service — Unplug the TV set from the wall outlet
and refer servicing to qualified service personnel under the following
conditions:
Cuando el televisor llegue al final de su vida útil, si se deshace de él de
forma inapropiada, el tubo de imagen puede explotar. Cuando desee
deshacerse de un televisor, solicite este servicio a un técnico de
reparación especializado.
Daños que requieren el servicio de reparación — En los casos
siguientes, desenchufe el televisor de la toma de la red y solicite los
servicios de personal de reparación especializado:
a. When the power cord or plug is damaged or frayed.
a. Cuando se haya dañado el cable de alimentación o el enchufe.
b. When liquid has been spilled into the TV set.
ANTENNA / ANTENA
Outdoor Antenna Grounding — If an outdoor antenna is installed,
follow the precautions below.
b. Cuando se haya vertido líquido dentro del televisor.
c. When the TV set has been exposed to rain or water.
c. Cuando el televisor haya estado expuesto a la lluvia o al agua.
An outdoor antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where
it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM,
EXTREME CARE SHOULD BE TAKEN TO KEEP FROM
CONTACTING SUCH POWER LINES OR CIRCUITS AS
CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.
d. When the TV set has been subject to excessive shock by being
dropped, or the cabinet has been damaged.
d. Cuando el televisor haya estado expuesto a golpes excesivos o haya
caído, o su caja se haya dañado.
Be sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges. Section
810 of the National Electrical Code in the USA and Section 54 of the
Canadian Electrical Code in Canada provides information with respect
to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
e. When the TV set does not operate normally even though you follow
the operating instructions. Adjust only those controls that are
specified in the operating instructions. Improper adjustment of
other controls may result in damage and will often require extensive
work by a qualified technician to restore the TV set to normal
operation.
When the TV set exhibits a distinct change in performance. This
indicates a need for service.
Puesta a tierra de la antena exterior — Cuando instale una antena
exterior, tenga en cuenta las precauciones siguientes.
e. Cuando el televisor no funcione normalmente incluso al seguir las
instrucciones de operación. Ajuste solamente los controles indicados
en las instrucciones de operación, ya que un ajuste inadecuado de
otros controles podría resultar en daños y a menudo requerirán un
trabajo difícil por un técnico cualificado para devolver el televisor a
su funcionamiento normal.
Un sistema de antena esterior no deberá colocarse cerca de líneas de alta
tensión ni otros circuitos de iluminación o alimentación, ni donde
pueda entrar en contacto con tales líneas o circuitos.
CUANDO INSTALE UN SISTEMA DE ANTENA EXTERIOR,
TENGA EXTREMADO CUIDADO PARA EVITAR QUE ENTRE
EN CONTACTO CON TALES LÍNEAS DE ALIMENTACIÓN O
CIRCUITOS, YA QUE TAL CONTACTO PODRÍA RESULTAR
INVARIABLEMENTE FATAL.
Cuando el funcionamiento del televisor haya cambiado
notablemente — esto indica la necesidad del servicio de reparación.
Servicing — Do not attempt to service the TV set yourself. To open or
remove the covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
Cerciórese de que el sistema de antena esté puesto a tierra a fin de que
proporcione cierta protección contra sobretensiones y cargas estáticas.
La Sección 810 del Código Eléctrico Nacional (NEC) de EE.UU. y la
Sección 54 del Código Eléctrico Canadiense ofrecen informacón con
respecto a la puesta a tierra adecuada de una unidad de descarga de
antena, el tamaño de los conductores de puesta a tierra, la ubicación de
la unidad de descarga de la antena, la conexión de los electrodos de
puesta a tierra, y los requisitos de tales electrodos.
Reparación — No intente nunca reparar el televisor por sí mismo. La
apertura o extracción de cubiertas podría exponerle a tensiones
peligrosas u otros peligros. En caso de avería solicite los servicios de
personal de reparación cualificado.
Replacement Parts — When replacement parts are required, be sure
the service technician certifies in writing that he has used replacement
parts specified by the manufacturer that have the same characteristics as
the original parts. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
Reemplazo de piezas — Cuando sea necesario reemplazar piezas,
cerciórese de que el técnico de reparación utilice las piezas de reemplazo
especificadas por el fabricante u otras que posean las mismas
características que las originales. Las substituciones no autorizadas
podrían resultar en incendios, descargas eléctricas, u otros peligros.
Safety Check — Upon completion of any service or repairs to the TV
set, ask the service technician to perform routine safety checks (as
specified by the manufacturer) to determine that the TV set is in safe
operating condition, and to so certify.
Comprobación de seguridad — Al finalizar cualquier reparación de
este televisor, solicite al técnico de reparación que realice las
comprobaciones de sguridad (especificadas por el fabricante) para
determinar y certificar si el producto se encuentra en las condiciones de
operación apropiadas.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome to Toshiba ............................................ 6
Exploring your new TV .............................................6
Selecting a location for the TV ...................................6
Notice of possible TV stand instability.................. 6
Using the V-Chip Control (blocking) feature ...........20
Selecting a PIN code ...........................................20
Changing your PIN code ....................................21
Blocking programs by ratings ..............................22
Ratings definitions (MPAA, Youth TV, TV)........22
Unblocking programs temporarily ......................23
Blocking unrated movies and programs...............23
Blocking channels ...............................................24
Locking video inputs ...............................................25
Channel labels .........................................................26
Video labels .............................................................27
Watching picture-in-picture (PIP)............................28
Switching the main and small pictures .....................28
Changing the location of the PIP window................29
Freezing the PIP display ...........................................29
Watching multi-window PIP ...................................29
Adjusting the picture ...............................................30
Adjusting the picture quality ....................................30
Selecting the color temperature ................................30
Adjusting the picture preference...............................31
Displaying on-screen information ............................31
Setting the off timer .................................................31
Auto power off .........................................................31
Using the closed caption feature...............................32
Adjusting the sound .................................................33
Muting the sound ....................................................33
Selecting stereo/SAP broadcasts ...............................33
Adjusting the sound quality .....................................34
Using the surround sound feature ............................34
Selecting variable audio OUT ..................................35
Turning off the built-in speakers ..............................35
Using the sub-bass system (SBS) ..............................36
Viewing the demonstration (DEMO) mode ............36
Understanding the last mode memory feature ..........36
Connecting your TV ............................................. 7
Note regarding picture quality .............................. 7
Connecting a VCR ....................................................7
Connecting a cable converter box ..............................8
Connecting a cable converter box and VCR ...............8
Connecting a DVD player or satellite receiver and a
VCR ..........................................................................9
Connecting a DVD player with ColorStream™
(component video) and a VCR ................................10
Connecting two VCRs .............................................10
Connecting a camcorder ..........................................11
Connecting an audio amplifier.................................11
Using the remote control ................................. 12
Preparing the remote control for use ........................12
Installing the remote control batteries ......................12
Using the remote control with a Toshiba VCR or
cable TV converter ...................................................12
Programming the remote control for use with
a non-Toshiba VCR or cable TV converter ..............13
VCR code table...................................................13
Cable TV converter code table ............................14
Learning about the remote control ...........................15
Setting up your TV ............................................. 16
Changing the on-screen display language .................16
Selecting the antenna input......................................16
Selecting the signal source ........................................17
Watching video input ..............................................17
Programming channels into the TV’s memory .........17
Programming channels automatically..................17
Adding and erasing channels manually................18
Changing channels...................................................18
Appendix.............................................................. 37
Troubleshooting .......................................................37
Cleaning and care ....................................................38
Specifications ...........................................................38
Limited United States warranty................................39
Attention Canadian customers .................................39
Using the TV’s features..................................... 19
Adjusting the channel settings..................................19
Switching between two channels ..............................19
Programming your favorite channels ........................19
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome to Toshiba
Congratulations! You have purchased one of the finest color TVs on the
market. The goal of this manual is to guide you through setting up and
operating your Toshiba TV as quickly as possible. Please make sure you
have received the following items: TV, remote control, batteries, owner’s
manual, registration card, and extended service plan literature. If you
did not receive all of the items or if any of the items are damaged or
broken, please contact your Toshiba dealer. In addition, you may need
to purchase other audio or video cables to connect your equipment. See
“Connecting your TV” on page 7 for more information.
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
4
CH
9
7
VOL
CH RTN
ENT
100
Please read all safety and operating instructions carefully before you
proceed.
ADV/
PIP CH
MENU
.CAPT
C
Exploring your new TV
FAV
ENTER
FAV
You can operate your TV using the buttons on the front panel or the
remote control. The back panel provides all the terminal connections
you will need to connect other equipment to your TV.
RESET
EXIT
ADV/
PIP CH
STOP SOURCE
PLAY PIP
REC TV/VCR REW
FF
TV/Video
36A61
Volume
STILL LOCATE SWAP
Channel
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
CT-9946
VIDEO L/MONO
AUDIO
R
VIDEO-3 IN
POWER
Video 3
Remote Sensor
Menu
Power Indicator (Red)
ANT (75Ω)
Caution:
The plug has one prong wider than the other
and will fit only one way into a standard
electrical outlet (120 volt AC, 60 Hz). If the
plug does not fit into the outlet, try turning it
around. If the
ANT-1
OUT
ANT-2
IN
36A61 – Rear
OUT
DVD IN
COLOR
S-VIDEO
STREAM
INPUT
Y
VIDEO
VIDEO
Pb
L/MONO
L/MONO
L
plug still
wide prong
AUDIO
R
AUDIO
R
AUDIO
R
Pr
does not fit,
the outlet is
probably non-
standard and
must be
A
N
T
(
7
5
Ω
)
A
N
T
-
1
OUT
A
N
T
-
2
IN
OUT
D
V
D
I
N
S-VIDEO
VIDEO
COLOR
STREAM
INPUT
VIDEO 2
VIDEO 1
Y
VIDEO
MONO
L
/
L
Pb
L/MONO
AUDIO
AUDIO
Pr
AUDIO
R
R
R
VIDEO
2
VIDEO
1
ColorStream
(component video)
Video 2
Video 1
replaced by a qualified electrician. Do not
tamper with the plug or try to force it
into a non-standard outlet.
Selecting a location for the TV
• Place the TV on the floor or on the recommended TV stand (see
“Notice of Possible TV Stand Instability” at right).
NOTICE OF POSSIBLE
TV STAND INSTABILITY
• Place the TV in a location where light does not directly hit the
screen.
WARNING: RISK OF
SERIOUS PERSONAL
• Place the TV far enough from the walls to allow proper ventilation.
Inadequate ventilation may cause overheating, which may damage
the TV.
INJURY OR DEATH!
Use your TV with the Toshiba TV
stand recommended below only!
Use with other
The serial number is on the back of your TV. Record the number in
the space below. Refer to the model and serial numbers whenever you
communicate with your Toshiba dealer about this TV.
TV Model TV Stand
stands may result
36A61
ST3641
in instability,
causing possible injury or death.
36A61
Model number: ________________________
Serial number: ________________________
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your TV
If you have not connected electronic equipment before, or you have
NOTE REGARDING
PICTURE QUALITY
been frustrated in the past, you may wish to read this section.
When connecting video equipment,
such as a VCR or DVD player:
Note: Cables are not supplied.
• A coaxial cable is the standard cable that comes in from your
antenna or cable converter box. Coaxial cables use “F” connectors.
• For GOOD picture quality: Use
regular video cables.
• Audio and video cables are usually color coded according to use:
yellow for video; red and white for audio. The red audio cable is for
the stereo right channel; the white audio cable is for the stereo (or
mono) left channel. If you look at the rear panel of the TV, you will
see that the terminals are color coded in the same manner as the
cables.
• For BETTER picture quality: If your
equipment has S-video connections,
use S-video cables instead of regular
video cables.
• For BEST picture quality: If your
equipment has ColorStream
(component video) connections,
use component video cables
instead of regular or S-video cables.
Component video cables come in
sets of three.
• S-video cables provide better picture performance than standard
video cables. S-video cables can be used only with S-video compat-
ible components.
• ColorStreamTM (component video) cables come in sets of three.
A ColorStream (component video) connection will provide the best
picture performance.
Note: Do not connect a regular video
cable and an S-Video cable to VIDEO-1
(or VIDEO-2) at the same time. Doing
so will distort the picture.
Cable Types
Regular
Video Cable
Coaxial
(Antenna)
Cable
S-Video
Cable
Caution:
Do not plug in any power cords until you have
finished connecting all of your equipment.
Audio
Cable
ColorStream
(Component
Video) Cables
Connecting a VCR
This connection allows you to watch local channels and video pro-
grams, play or record on the VCR while watching TV, and record
from one channel while watching another channel.
You will need:
• one coaxial cable
• one pair of audio cables (one single audio cable for a mono VCR)
• one video cable
Note:
From Cable or Antenna
TV
If you have a mono VCR, connect L/Mono to
VCR Audio OUT using only one audio cable.
ANT (75Ω)
If you have an S-VHS VCR, use an S-video
cable instead of a regular video cable.
ANT-1
OUT
ANT-2
IN
OUT
DVD IN
COLOR
Do not connect a regular video cable and an
S-video cable to Video-1 (or Video-2) at the
same time. Doing so will distort the picture.
S-VIDEO
STREAM
INPUT
Y
VIDEO
VIDEO
Pb
L/MONO
L/MONO
L
AUDIO
R
AUDIO
R
AUDIO
R
Pr
VIDEO 2
VIDEO 1
Stereo VCR
VIDEO
AUDIO
L
R
IN
IN from ANT OUT to TV
CH 3
CH 4
OUT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a cable converter box
Note:
This connection allows you to watch basic and premium cable
channels. To use the TV features (such as PIP swap, channel y z,
channel block, favorite channels, or channel labels ), select ANT-1. To
view premium channels, select ANT-2, tune the TV to channel 3 or 4
(whichever channel is vacant in your area), and use the converter box
to change channels.
When you use a converter box with your TV,
the remote control may not operate certain
features, such as PIP swap, channel y z,
channel block, favorite channels, or channel
labels.
You will need:
• two coaxial cables
From Cable
ANT (75Ω)
IN
OUT
DVD IN
Cable
Converter
Box
Connecting a cable converter box and VCR
This connection allows you to watch and record basic and premium
cable channels, as well as watch videotapes. Set the TV signal source
to Video1 (see “Watching video input” on page 17). Tune the VCR to
channel 3 or 4 (the same channel as the converter box output switch),
and use the cable converter box to change channels. Set the PIP
source to “TV” (see page 28).
You will need:
• three coaxial cables
• one pair of audio cables (one single audio cable for a mono VCR)
• one video cable
• one cable splitter
From Cable
TV
ANT (75Ω)
OUT
OUT
Cable
Signal
Splitter
IN
Note:
ANT-1
OUT
ANT-2
When you use a converter box with your
TV, the remote control may not operate
certain features, such as PIP swap,
channel y z, channel block, favorite
channels, or channel labels.
IN
OUT
DVD IN
COLOR
S-VIDEO
STREAM
INPUT
Y
VIDEO
VIDEO
Pb
L/MONO
L/MONO
L
AUDIO
R
AUDIO
R
AUDIO
R
Pr
If you have a mono VCR, connect
L/Mono to VCR Audio OUT using only
one audio cable.
VIDEO 2
VIDEO 1
IN
Cable
Converter Box
OUT
Stereo VCR
If you have an S-VHS VCR, use an
S-video cable instead of a regular video
cable.
VIDEO
AUDIO
L
R
IN
IN from ANT OUT to TV
Do not connect a regular video cable
and an S-video cable to Video-1 (or
Video-2) at the same time.
CH 3
CH 4
OUT
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a DVD player or satellite receiver
and a VCR
This connection allows you to watch DVD/satellite, VCR, or TV
programs. You can record from the DVD player/satellite receiver or
TV. You can also record one TV channel while watching another
channel.
Note: If your DVD player has component video connections, follow
the connection instructions under “Connecting a DVD player with
ColorStream™ (component video) and a VCR” on page 10.
You will need:
• one coaxial cable
• three pairs of audio cables (one pair and two single audio cables
for a mono VCR)
• two regular video cables
• one S-video cable
Note:
To Satellite
DVD / Satellite Receiver
You can use a regular video cable instead of
an S-video cable between the TV and DVD
player/satellite receiver, but the picture quality
will decrease.
The illustration at left shows one S-video
cable and one pair of audio cables connected
from the DVD player/satellite receiver to
Video-1 on the TV.
ANT (75Ω)
Do not connect a regular video cable and an
S-video cable to Video-1 (or Video-2) at the
same time. Doing so will distort the picture.
IN
OUT
DVD IN
When recording, set Audio Out to FIX
(see “Selecting variable audio OUT”
on page 35). With Audio Out set to
FIX, the TV’s volume setting during
recording will not affect the sound
level being recorded.
Stereo VCR
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Player with ColorStream (component video)
Connecting a DVD player with
ColorStream™ (component video) and
a VCR
This connection allows you to watch DVD, VCR, or
TV programs, and record DVD or TV programs
(when authorized). You can record from one source
while watching a program from another source.
TV
ANT (75Ω)
Your TV has ColorStream (component video) connec-
tions. Connecting your TV to a component video
compatible DVD player (such as a Toshiba DVD
player with ColorStream™) can greatly enhance
picture quality and performance.
IN
OUT
DVD IN
You will need:
• one coaxial cable
• three pairs of audio cables (one pair and two
single audio cables for a mono VCR)
• two regular video cables
Stereo VCR
• one set of ColorStream (component) video cables
Note:
For the best picture performance, use ColorStream
(component video) cables between the TV and DVD
player. To record from the DVD player, the DVD player
and TV must select VIDEO 1.
Connecting two VCRs
This connection allows you to record from one VCR to another VCR
while watching a video program. You can also record from one TV
channel while watching another channel.
Note:
When recording, set Audio Out to
FIX (see “Selecting variable audio
OUT” on page 35). With Audio Out
set to FIX, the TV’s volume setting
during recording will not affect the
sound level being recorded.
You will need:
• one coaxial cable
• two pairs of audio cables (two single audio cables for mono VCRs)
• two video cables
Stereo VCR [Playback]
Caution:
VIDEO
AUDIO
L
The unauthorized recording of
television programs, videotapes,
DVDs, and other materials may
infringe upon the provisions of
copyright laws.
R
IN
IN from ANT OUT to TV
CH 3
CH 4
OUT
TV
ANT (75Ω)
ANT-1
OUT
ANT-2
Note:
IN
If you have S-VHS VCRs, use S-video cables
instead of regular video cables.
OUT
DVD IN
COLOR
S-VIDEO
STREAM
INPUT
Y
VIDEO
VIDEO
Do not connect a regular video cable and an
S-video cable to Video-1 (or Video-2) at the
same time.
Pb
L/MONO
AUDIO
R
L/MONO
L
AUDIO
R
AUDIO
R
Pr
Do not connect the same VCR to the output
and input jacks on the TV at the same time.
VIDEO 2
VIDEO 1
Stereo VCR
[Recording]
VIDEO
AUDIO
L
R
IN
IN from ANT OUT to TV
CH 3
CH 4
OUT
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a camcorder
This connection allows you to watch videos recorded on a camcorder.
Note:
If your camcorder has an S-video connection,
an S-video cable will provide better picture
performance than a regular video cable.
You will need:
• one pair of audio cables
• one video cable
Do not connect a regular video cable and an
S-video cable to Video-1 (or Video-2) at the
same time.
Camcorder
S-VHS Camcorder
VIDEO AUDIO
S-VIDEO
VIDEO AUDIO
OUT
L
OUT
L
R
R
TV Back
ANT (75Ω)
ANT-1
OUT
ANT-2
IN
OUT
DVD IN
COLOR
S-VIDEO
TV Front
STREAM
INPUT
Y
VIDEO
VIDEO
Pb
L/MONO
AUDIO
R
L/MONO
L
VIDEO L/MONO
AUDIO
VIDEO-3 IN
R
AUDIO
R
AUDIO
R
Pr
VIDEO 2
VIDEO 1
Connecting an audio amplifier
This connection allows you to use an audio amplifier to adjust the
audio level. This connection also allows you to use external speakers.
Note:
To control the audio, both the TV and the
amplifier must be turned on, and the volume
of both must be set above 0, or you will not
hear any sound. See “Selecting variable audio
OUT” on page 35 for additional details.
You will need:
• one pair of audio cables
To Cable, Cable Box,
or Antenna
Audio Amplifier
TV
ANT (75Ω)
IN
OUT
DVD IN
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
Using the remote control
The remote control provided with your TV
may or may not operate certain features on
your VCR, cable TV converter, or other
electronic equipment. Refer to the owner’s
manuals provided with your other equipment
to see which features are available. In
addition, the other remote controls may have
buttons not available on your TV’s remote
control. If you would like to use those features
or buttons, you may need to use the original
remote controls provided with your other
equipment.
Preparing the remote control for use
The remote control will operate your TV, most VCR models, and
most cable TV converters together, even if they are different brands.
• If you will be using your TV with a Toshiba VCR or cable TV
converter, your remote control is already programmed and ready
to use. See “Using the remote control with a Toshiba VCR or
cable TV converter” below.
• If you own a non-Toshiba VCR or converter and want to use your
TV remote control to operate it, you will need to program the
remote control. See “Programming the remote control for use
with a non-Toshiba VCR or cable TV converter” on page 13.
Caution:
• Dispose of batteries in a designated
disposal area. Do not throw batteries
into a fire.
Installing the remote control batteries
To install the batteries:
1. Slide the battery cover off the back of the remote control.
• Do not mix battery types or combine used
batteries with new ones.
• Remove dead batteries immediately to
prevent battery acid from leaking into the
battery compartment.
• If you do not intend to use the remote
control for a long time, remove the
batteries.
2. Install two “AA” size batteries. Match the + and – symbols on
RECALL
POWER
LIGHT RECALL
the batteries to the symbols on the battery compartment.
POWER
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
TV/CABLE/VCR
switch
2
5
8
0
3
6
1
4
CH
CH (Channel)
Channel
Numbers
9
7
VOL
CH RTN
3. Slide the battery cover back onto the remote control until the
lock snaps.
ENT
100
ENT (used for the “ENTER”
command with some VCRs
and cable TV converters)
ADV/
PIP CH
MENU
.CAPT
C
Using the remote control with a Toshiba VCR
or cable TV converter
FAV
ENTER
FAV
To control a Toshiba VCR:
RESET
EXIT
ADV/
Set the TV/CABLE/VCR switch to the VCR position. The
shaded buttons in the illustration at right will then control the
VCR. The unshaded buttons will operate the TV as usual.
PIP CH
STOP
PLAY
STOP SOURCE
PLAY PIP
REC TV/VCR REW
FF
To control a Toshiba cable TV converter:
FAST FORWARD
REWIND
Set the TV/CABLE/VCR switch to the CABLE position. The
shaded buttons in the top portion of the illustration at right will
then control the cable TV converter.
STILL LOCATE SWAP
TV/VCR
RECORD
CT-9946
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the remote control for use
with a non-Toshiba VCR or cable TV converter
The remote control provided with your Toshiba TV is
preprogrammed to operate Toshiba VCRs and cable TV converters.
RECALL
POWER
POWER
LIGHT RECALL
TV
To operate a non-Toshiba VCR or converter using the remote
control provided with your TV:
CABLE
VCR
MUTE TV/VIDEO TIMER
1. Refer to the VCR and cable TV converter code tables (below
and on the next page) to find the corresponding code for your
VCR or converter brand.
TV/CABLE/VCR
switch
2
5
8
0
3
6
1
4
CH
CH (Channel)
If more than one code is listed, try each one separately until you
find the one that works.
Channel
Numbers
9
7
VOL
CH RTN
2. If you are programming the remote control to operate your:
ENT
100
ENT (used for the “ENTER”
command with some VCRs
and cable TV converters)
• VCR: Set the TV/CABLE/VCR switch on the remote control
to “VCR.”
ADV/
PIP CH
MENU
.CAPT
C
• Cable TV converter: Set the TV/CABLE/VCR switch on the
remote control to “CABLE.”
3. While holding down RECALL, press the CHANNEL
NUMBERS to enter the three-digit code for your VCR or
cable TV converter brand.
4. Point the remote control at the VCR or converter, and press
POWER to test the code.
• If the VCR or converter responds, you entered the correct
code.
Note:
•
Every time you replace the batteries, you
must reprogram the remote control.
• If the VCR or converter does not respond, repeat steps 1–4
using another code.
•
Some newer VCRs are capable of working
on either of two remote codes. These
VCRs have a switch labeled “VCR1/
VCR2.” If your VCR has this kind of switch
and does not respond to any of the codes
for your VCR brand, set the switch to the
other position (VCR1 or VCR2) and
reprogram the remote control.
5. Set the TV/CABLE/VCR switch to “TV” to control the TV.
For future reference, write down the codes you used:
VCR code: _____________________
Cable TV converter code: _____________________
VCR code table
Brand
Code
Adventura
Aiko
Aiwa
019
297
019
CCE
Citizen
Colt
091, 297
056, 297
091
Fisher
Fuji
Funai
066, 073, 085, 123
052, 054
019, 344
Akai
060, 068, 080, 125,
261
054
259
056
259
123
206
Craig
056, 066, 091, 259
054, 060, 079
259
039, 064, 297
039
019
056
056
Garrard
GE
Go Video
Goldstar
Gradiente
019, 344
054, 079, 084, 221
251, 298
037, 056, 057
019
Curtis Mathes
Cybernex
Daewoo
Daytron
Dynatech
Electrohome
Electrophonic
Emerex
American High
Asha
Audiovox
Beaumark
Bell & Howell
Brandt
Harley Davidson 019
Harman/Kardon
Harwood
Headquarter
HI-Q
057, 094
087, 091
065
Broksonic
140, 203, 230, 314,
051
380
056
054
039
100
Emerson
019, 021, 056, 062,
080, 087, 140, 203,
227, 228, 230, 231,
297, 313, 314, 380,
498
066
Calix
Hitachi
060, 061, 084, 124,
185, 254
060
027, 060, 086
057, 060, 086
Canon
Capehart
Carver
Jensen
JVC
Kenwood
13
Download from Www.Somanuals.com. All Manuals Search And Download.
VCR code table (cont.)
Brand
Code
KLH
091
054, 056
019, 227
091
Sanky
Sansui
Sanyo
Scott
058, 067
060, 086
Garrard
CG Electronics
Gemini
General Instrument 030, 295
Gold Star
Hamlin
172
075
034, 089
Kodak
Lloyd
Logik
LXI
065, 066, 123, 259
062, 064, 140, 203,
229, 230, 231
054, 056, 061, 065,
066, 073, 085, 123,
124
067, 081
091
259
091
051, 052, 053, 054
061
019, 054, 062, 100,
129
019, 344
060
019, 060
054, 181
019, 054, 056, 071
206
227, 259
056
059, 163
028, 039, 053, 278,
292
030
026
Magnavox
054, 058, 100, 129,
168
259
054, 100
056
054
054
019, 054, 056, 058,
065, 066, 067, 123,
259
Sears
Magnin
Marantz
Marta
Matsushita
MEI
Hitachi
Hytex
Jasco
Sharp
Shintom
Shogun
Singer
Sony
STS
Sylvania
172
Jerrold
022, 030, 031, 033,
034, 066, 295
052
046
019
Memorex
Macom
Magnavox
Memorex
Movietime
NSC
MGA
062, 080
175
MGN Technology 259
Minolta
Mitsubishi
Symphonic
Tatung
Teac
Technics
Teknika
Telefunken
TMK
089, 175
026, 038, 267
019, 040, 126
019
044, 046, 047, 048,
049, 050, 172
042, 163, 552
061, 124
062, 080, 086, 094,
192, 233, 261
054, 067
019, 259
019, 091
077
Oak
Panasonic
Paragon
Philips
Motorola
MTC
Multitech
NAD
Pioneer
Popular Mechanics 419
Pulsar
Toshiba
062, 064, 085, 229,
231, 385
NEC
057, 059, 060, 069,
019
086
056
259
054
Totevision
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Wards
056, 259
259
064
057, 059
059, 064, 080
259
019, 054, 061, 066,
067, 081, 091, 168,
231, 259
019, 054, 091
057
052, 053, 058
RCA
Regal
Recoton
Regency
Rembrandt
Runco
040
039, 278, 292
419
021
030, 089
019
Nikko
Noblex
Olympus
Optimus
Optonica
Orion
056, 067, 077, 123
081
498
054, 096, 181, 244,
473
054, 056, 057, 059,
061, 073, 259
Samsung
059, 163
Panasonic
Scientific Atlanta 025, 027, 036, 296
Signal
Signature
SL Marx
Sprucer
Standard
034, 059
030
059
Penney
XR-1000
Yamaha
Zenith
Pentax
Philco
061, 084, 124
054
040
Philips
Pilot
Pioneer
Portland
Protec
054, 081, 100, 129
056
077, 086
039
091
058
065
065
Components
174
022, 034, 066
034, 059
034
020
059
020
031, 032, 078
019
034
041, 172
026
Cable TV converter
code table
Starcom
Stargate
Starquest
Sylvania
Teleview
Texscan
Tocom
Toshiba
Tusa
Unika
Brand
Code
ABC
020, 022, 027, 030,
Pulsar
032, 033, 036, 066
Quarter
Quartz
Quasar
Radio Shack
Radix
Antronix
Archer
Belcor
041
041, 058, 172
075
054, 096
019, 056, 344
056
Cable Star
Cabletenna
Cableview
Century
Citizen
075
041
041
172
Randex
RCA
056
United Artists
United Cable
Universal
061, 079, 084, 096,
124, 125, 168, 221
019, 054, 056, 065,
066, 067, 081, 085,
123, 259
053
058
064, 259
022
041, 058, 075, 096,
172, 210
046, 079, 230
019
172
Realistic
Colour Voice
Comtronics
Contec
044, 050
059, 079
038
Viewstar
Zenith
Zentek
Ricoh
Runco
Samsung
419
Dae Ryung
Eastern
027
021
Focus
419
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Learning about the remote control
LIGHT illuminates the keys
RECALL
POWER
LIGHT
POWER
LIGHT RECALL
RECALL displays on-screen
information (pages 21, 22)
TV
TV/CABLE/VCR switch
MUTE
CABLE
VCR
MUTE TV/VIDEO TIMER
TV/CABLE/VCR switch switches
among TV, Cable, and VCR inputs
(page 12)
TIMER
TV/VIDEO
2
5
8
0
3
6
1
4
POWER turns the TV on and off
CH
CH (Channel)
MUTE turns off the sound (page 33)
Channel Numbers
VOL (Volume)
TIMER sets the TV to turn off at a specific
time (page 31)
9
7
VOL
CH RTN
ENT
100
CH RTN (Channel Return)
MENU
TV/VIDEO selects the signal input source
(page 17)
ADV/
PIP CH
MENU
C.CAPT
(Closed Caption)
Channel yz cycles through
.CAPT
C
programmed channels (page 17)
FAV
PIP CH
FAV
ENTER
FAV
Channel Numbers (0–9, 100) directly
tune channels (page 18)
RESET
VOL yz adjusts the volume level
Reset
EXIT
EXIT
ADV/
PIP CH
CH RTN (Channel Return) returns to the
last viewed channel (page 19)
STOP SOURCE
PLAY PIP
C.CAPT opens the Closed Caption menu (page 32)
REC TV/VCR REW
FF
PIP (or VCR) Buttons
MENU accesses on-screen menus (page 16)
STILL LOCATE SWAP
yz x • (Up/Down/Left/Right Arrows) select or adjust
menu items when a menu is on-screen (page 17)
FAV zy (Left/Right Arrows) select channels you
CT-9946
programmed as favorite channels (page 19)
EXIT sets menu information and closes menus (page 23)
PIP Buttons access PIP functions when the TV/Cable/
VCR switch is set to TV (pages 28, 29)
PIP turns the PIP and Multi-Window feature on and off
(one press for 1/9-size PIP window; two presses for 1/16-size
PIP window; three presses for the Multi-Window feature)
SOURCE selects the PIP signal input source
PIP CH yz (Up/Down Arrows) select PIP channels (when PIP
is on-screen)
STILL freezes the PIP display
LOCATE changes the location of the PIP window
SWAP switches the main and PIP pictures
Note: When the TV/Cable/VCR switch is set to “VCR,” the PIP buttons
function instead as VCR buttons (STOP, PLAY, REC, TV/VCR, REW, FF; see
page 12).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
TV Front Panel
After installing the batteries and programming the remote control, you
will need to set some preferences on your TV using the menu system.
You can access the menus using the buttons on your TV or remote
control.
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
• When you make a menu selection, your changes occur immediately.
You do not have to press MENU or EXIT to save your changes.
Note: The TV front panel does not have an EXIT button.
yzx •
MENU
• When you are finished programming the menus, you can press
EXIT to clear the on-screen display, or wait 15 seconds and the
on-screen display will disappear automatically. Your changes are
automatically saved either way.
POWER
LIGHT RECALL
Changing the on-screen display language
You can choose from three different languages (English, French, or
Spanish) for the on-screen display of menus and messages.
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
To select an on-screen display language:
1. Press MENU .
2. Press x or • until the SET UP menu appears.
3. Press y or z to highlight LANGUAGE.
4. Press x or • to highlight your desired language.
CH
4
7
9
VOL
CH RTN
ENT
100
ADV/
PIP CH
MENU
MENU
.CAPT
C
SET UP
CONFIGURE
FAV
ENTER
FAV
LANGUAGE:
LANGUE:
[ENGLISH] FRANCAIS ESPANOL
ENGLISH [FRANCAIS] ESPANOL
ANT1/2:
[ANT1] ANT2
[TV] CABLE
ANT1/2:
[ANT1] ANT2
[TV] CABLE
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
TV/CABLE:
PROGRAMME CAN
ADD/EFF:
MORE
RESET
EXIT
[ADD] ERASE
[ADD] EFF
EXIT
ADV/
PIP CH
[
]
[
]
MOVE
SELECT
[
]
[
]
BOUGER
CHOISIR
Selecting the antenna input
You can connect to one of two different antenna input sources
(ANT 1 or ANT 2).
To select the antenna input:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight ANT 1/2.
4. Press x or • to highlight either ANT 1 or ANT 2, depending on
the antenna terminal you wish to use.
SET UP
LANGUAGE:
[ENGLISH] FRANCAIS ESPANOL
ANT1/2:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ANT1] ANT2
[TV] CABLE
[ADD] ERASE
[
]
[
]
MOVE
SELECT
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the signal source
TV/VIDEO
CHANNEL yz
Use the TV/VIDEO button on the remote control or TV to monitor or
change the signal source connected to your TV.
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
To monitor the signal source:
Press TV/VIDEO once. The current signal source displays in green.
To change the signal source:
Repeatedly press TV/VIDEO to select either VIDEO 1, VIDEO 2,
VIDEO 3, ColorStream, ANT 1, or ANT 2. The selected signal
source displays in green.
yz x •
MENU
VIDEO 1
VIDEO 2
VIDEO 3
ANT 1
POWER
LIGHT RECALL
ColorStream ANT 2
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
TO SELECT PUSH TV/VIDEO
TV/VIDEO
2
5
8
0
3
6
1
4
Watching video input
To view a signal from other devices connected to your TV
(such as a VCR or DVD player):
CH
CH (Channel)
Channel
Numbers
9
7
VOL
Repeatedly press TV/VIDEO on the remote control or TV to select
either VIDEO 1, VIDEO 2, VIDEO 3, or ColorStream. (For device
connection information, see “Connecting your TV” on page 7).
CH RTN
ENT
100
ADV/
PIP CH
MENU
MENU
.CAPT
C
Programming channels into the TV’s memory
When you press CHANNEL LM on the TV or remote control,
the TV stops only on the channels stored in the TV’s memory.
FAV
ENTER
FAV
RESET
Note: To tune the TV to a channel not programmed into the memory,
EXIT
ADV/
PIP CH
use the CHANNEL NUMBERS on the remote control.
Follow the steps below and on the next page to program channels into
the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and
store them in the TV’s memory. After the channels are stored automati-
cally, you can manually add or erase individual channels (see page 18).
If you use both ANT-1 and ANT-2 terminals, you will need to program
channels for each signal source.
To program channels automatically:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight TV/CABLE.
4. Press x or • to highlight TV (if you use an antenna) or CABLE (if
you use cable).
5. Press z to highlight CH PROGRAM.
SET UP
SET UP
LANGUAGE:
LANGUAGE:
[ENGLISH] FRANCAIS ESPANOL
[ENGLISH] FRANCAIS ESPANOL
ANT1/2:
TV/CABLE:
[ANT1] ANT2
[TV] CABLE
ANT1/2:
TV/CABLE:
[ANT1] ANT2
[TV] CABLE
CH PROGRAM
ADD/ERASE:
MORE
CH PROGRAM
ADD/ERASE:
MORE
[ADD] ERASE
[ADD] ERASE
[
]
[
]
[
]
[
]
MOVE
SELECT
MOVE
SELECT
(Continued on next page)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press x or • to start automatic channel programming (“CH
PROGRAM” displays on-screen). The TV automatically cycles
through every TV or cable channel (depending on which you
selected), and stores all active channels in the TV’s memory.
CHANNEL yz
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
7. When automatic channel programming is complete, the message
“CH Programming Completed” appears.
8. Press CHANNEL LM to view the programmed channels.
yzx •
MENU
Adding and erasing channels manually
After you have automatically programmed the channels into the TV’s
memory, you can manually add and erase individual channels.
To add a channel to or erase a channel from the TV’s memory:
1. Tune the TV to the channel you want to add or erase. If you are
adding a channel, you will need to use the CHANNEL
NUMBERS to select the channel.
POWER
LIGHT RECALL
TV
CABLE
VCR
2. Press MENU.
MUTE TV/VIDEO TIMER
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight ADD/ERASE.
2
5
8
0
3
6
1
CH
CH (Channel)
4
7
Channel
Numbers
SET UP
9
VOL
LANGUAGE:
CH RTN
[ENGLISH] FRANCAIS ESPANOL
ANT1/2:
TV/CABLE:
[ANT1] ANT2
[TV] CABLE
ENT
100
CH PROGRAM
ADD/ERASE: [ADD] ERASE
MORE
ADV/
PIP CH
MENU
MENU
CAPT
.
C
[
]
[
]
MOVE
SELECT
FAV
ENTER
FAV
5. Press x or • to highlight ADD or ERASE, whichever function
you want to perform.
RESET
6. Press MENU.
EXIT
ADV/
PIP CH
EXIT
7. Repeat steps 1–6 for other channels you want to add or erase,
or press EXIT to return to normal TV viewing.
Changing channels
To change to the next programmed channel:
Press CHANNEL yz.
To change to a specific channel (programmed or unprogrammed):
Press the CHANNEL NUMBERS (0–9 and 100).
Note: For channels 100 and higher, press the 100 button, and
then the next two channel numbers (for example, to select
channel 100, press 100, 0, 0; to select channel 125, press
100, 2, 5).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
POWER
LIGHT RECALL
Adjusting the channel settings
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
Switching between two channels
You can switch between two channels without entering an actual
channel number each time.
2
5
8
0
3
6
1
4
CH
CH (Channel)
To switch between two channels:
1. Select the first channel you want to view.
Channel
Numbers
9
7
VOL
CH RTN
2. Select a second channel using the CHANNEL NUMBERS
ENT
100
CH RTN
MENU
(0–9 and 100).
ADV/
PIP CH
MENU
3. Press CH RTN (channel return). The previous channel will
CAPT
.
C
display.
Every time you press CH RTN, the TV will switch back and forth
between the last two channels you tuned the TV to.
FAV
ENTER
FAV
FAV
RESET
EXIT
ADV/
PIP CH
EXIT
Programming your favorite channels
The Favorite Channel feature allows you to use the FAV ML buttons
on the remote control to cycle through your favorite channels,
skipping over channels you do not normally watch. You can program
a maximum of 12 favorite channels.
Note: You can still use CHANNEL LM to cycle through all the
channels you previously programmed into the TV’s memory (see
“Adding channels to the TV’s memory” on page 17).
To program your favorite channels:
1. Tune the TV to a channel you want to program as a favorite
channel.
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight FAVORITE CH.
SET UP
MORE
V-CHIP CONTROL
FAVORITE CH
CH LABEL
VIDEO LABEL
TIMER:
DEMO:
0 MIN
START [STOP]
[
]
[
]
MOVE
START
5. Press x or • to display the FAVORITE CH menu. SET/CLEAR
will be highlighted.
6. Press x or • to highlight SET.
7. Press z to add the current channel to the list.
8. Press MENU.
SET UP
FAVORITE CH
[SET] CLEAR
2
0
0
5
0
0
6
0
0
11
0
0
[TV: CYAN, CABLE: BLUE]
[
]
[
]
SELECT
SET
9. Repeat steps 1–8 for up to 12 channels, or press EXIT to close
the menu.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
To select your favorite channels:
Note:
Press FAV zy on the remote control to cycle through the favorite
channels you programmed.
The FAV zy buttons function as menu x •
buttons when a menu is on-screen.
Note: The FAV zy buttons will not work unless you program at
least one favorite channel.
To clear a favorite channel:
1. Tune the TV to the channel you want to clear from your favorite
channel list.
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight FAVORITE CH.
2
5
8
0
3
6
1
4
CH
5. Press x or • to display the FAVORITE CH menu. SET/CLEAR
will be highlighted.
9
7
6. Press x or • to highlight CLEAR.
VOL
CH RTN
ENT
100
ADV/
PIP CH
MENU
SET UP
MENU
.CAPT
FAVORITE CH
SET [CLEAR]
C
2
0
0
5
0
0
6
0
0
0
0
0
FAV
ENTER
FAV
FAV
[TV: CYAN, CABLE: BLUE]
RESET
[
]
[
]
SELECT
CLEAR
EXIT
ADV/
PIP CH
EXIT
7. Press z to clear the current channel number from the list.
8. Press MENU.
10. Repeat steps 1–8 for other channels you want to clear from your
favorite channel list, or press EXIT to close the menu.
Using the V-Chip Control (blocking) feature
You can use the V-Chip Control feature to block certain programs or
channels, to prevent others from viewing them.
Selecting a PIN code
Before you can block programs or channels, you must select a personal
identification number (PIN) code. Your PIN code allows you to access
the V-Chip Control menu, and prevents others from changing the
rating and blocking limits you set.
To select your PIN code and access the V-Chip Control menu:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the “Enter PIN Code” screen.
SET UP
SET UP
MORE
BLOCKING IS ACTIVE
PLEASE ENTER PIN CODE
_ _ _ _
V-CHIP CONTROL
FAVORITE CH
CH LABEL
VIDEO LABEL
TIMER:
0 MIN
START [STOP]
DEMO:
[
]
SELECT [0–9] END [EXIT]
[
]
MOVE
START
20
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After the code is entered, the V-Chip Control menu
appears.
RECALL
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
SET UP
2
5
8
0
3
6
1
4
ENABLE BLOCKING [Y] N
SET RATING
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
VIDEO LOCK
CH
Channel
Numbers
OFF
[
9
7
VOL
CH RTN
]
[
]
MOVE
SELECT
ENT
100
V-Chip Control (Blocking) Menu
ADV/
PIP CH
MENU
MENU
6. Press y or z to highlight ENABLE BLOCKING.
.CAPT
C
7. Press x or • to highlight “Y,” which enables all blocking by
activating the V-Chip. See “Blocking programs by ratings” on
page 22, “Blocking unrated movies or programs” on page 23,
and “Blocking channels” on page 24.
FAV
ENTER
FAV
RESET
EXIT
ADV/
PIP CH
EXIT
(Note: Highlight “N” to deactivate the V-Chip Control feature
and disable blocking.)
Changing your PIN code
1. Press MENU.
Note:
If you forget your PIN code:
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the Enter PIN Code screen.
• Follow steps 1–4 under “Changing your PIN
code” at left.
• Then press RECALL four times within five
seconds.
5. Use the Channel Number buttons (0–9) to enter your existing
PIN code. After the code is entered, the V-Chip Control menu
appears.
This allows you to proceed to the V-Chip
Control menu and reset your PIN code.
6. Press y or z to highlight NEW PIN CODE.
7. Press x or • to display the New PIN Code screen.
SET UP
SET UP
ENABLE BLOCKING
SET RATING
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
[Y] N
PLEASE ENTER NEW PIN CODE
_ _ _ _
VIDEO LOCK
OFF
SELECT [0–9] END [EXIT]
[
]
[
]
MOVE
SELECT
8. Use the CHANNEL NUMBERS (0–9) to enter a new PIN
code. After the new code is entered, the V-Chip Control menu
appears.
9. Press EXIT to return to normal TV viewing.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking programs by ratings
Note:
The Motion Picture Association of America (MPAA) uses a rating
system to qualify motion picture content. Television broadcasters
employ a similar rating system to qualify the content of television
programs. The MPAA, Youth TV, and TV ratings work with the
V-Chip feature to allow you to block access to programs that exceed
the rating limits you set.
Press RECALL to see the rating of the program
you are viewing. Not all programs are rated,
however. To block programs or movies that are
not rated, see “Blocking unrated movies and
programs” on page 23.
Ratings definitions
MPAA Ratings
TV Ratings
MA
Mature audience only. This program is specifically
designed to be viewed by adults and therefore
may be unsuitable for children under 17.
X
For adults only.
NC17
R
Not intended for anyone 17 or under.
Restricted. Under 17 requires an accompanying
parent or adult guardian.
Dialog
Intensely suggestive dialog
Language Crude or indecent language
Sex
Violence
PG13
PG
Parents strongly cautioned. Some material may
not be appropriate for children under 13.
Explicit sexual activity
Graphic violence
Parental guidance suggested. Some material
may not be appropriate for children.
14
Parents strongly cautioned. This program contains
some material that many parents would find
unsuitable for children under 14 years of age.
G
General audience. Appropriate for all ages.
Dialog
Frequent suggestive dialog
Youth TV Ratings
Language Frequent coarse language
Y7, Y7FV
Directed to older children. Programs rated Y7
Sex
Violence
Intense sexual situations
Intense violence
are designed for children 7 and above.
Programs rated Y7FV contain fantasy violence
that may be more intense or combative than
Y7-rated programs.
PG
Parental guidance suggested. This program
contains material that parents may find unsuitable
for younger children.
Y
For all children. Programs rated Y are designed
to be appropriate for all children.
Dialog
Some suggestive dialog
Language Occasional coarse language
Sex
Violence
Some sexual situations
Moderate violence
G
General audience. Most parents would find this
program suitable for all ages.
No DLSV Programs without any Dialog, Language, Sex, or
Violence ratings.
To block programs by rating:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the “Enter PIN Code” screen.
RECALL
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit PIN
code. After the code is entered, the V-Chip Control menu appears.
2
5
8
0
3
6
1
4
6. Press y or z to highlight ENABLE BLOCKING.
CH
7. Press x or • to highlight “Y,” which enables all blocking by activating
the V-Chip. (Note: Highlight “N” to deactivate the V-Chip Control
feature and disable blocking.)
Channel
Numbers
9
7
VOL
CH RTN
ENT
100
ADV/
PIP CH
MENU
MENU
SET UP
CAPT
.
C
ENABLE BLOCKING [Y] N
SET RATING
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
FAV
ENTER
FAV
VIDEO LOCK
OFF
RESET
[
]
[
]
MOVE
SELECT
EXIT
ADV/
PIP CH
22
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press y or z to highlight SET RATING.
9. Press x or • to display the Set Rating menu.
10. Press y or z to highlight MPAA Rating, Youth TV Rating, or
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
TV Rating.
11. Press • to select (or x to deselect) the ratings to be blocked.
Blocked ratings will be marked with “x”; unblocked ratings will
will be marked with “✔.” All ratings higher than the ones that are
selected (“x”) are blocked as well. For example, if you block the
MPAA rating R, programs with the higher ratings NC17 and X
will also be blocked.
MUTE
2
5
8
0
3
6
1
4
CH
9
7
VOL
CH RTN
ENT
100
ADV/
PIP CH
MENU
MENU
SET UP
SET UP
.CAPT
C
MPAA RATING:
TV RATING:
DIALOG:
MA 14 PG
x
G
X
NC17 R PG13 PG
G
x x
LANGUAGE:
SEX:
FAV
ENTER
FAV
YOUTH TV RATING:
VIOLENCE:
NO DLSV:
Y
Y7FV Y7
BACK TO V-CHIP MENU
TV RATING
RESET
[
]
[
]
[
]
[
]
MOVE
SELECT
MOVE
SELECT
EXIT
EXIT
ADV/
PIP CH
12. When you finish selecting the program ratings to be blocked:
• To return to the V-Chip menu, press y or z to highlight
BACK TO V-CHIP MENU, and then press x or •.
• To return to normal TV viewing, press EXIT.
Unblocking programs temporarily
When you try to view a program with a ratings block, a message
appears stating that the program has been blocked because the
program’s rating exceeds the set limits. To temporarily override the
block and view the program, press MUTE and enter your PIN code.
To reset your original ratings blocks, turn the TV off and then on
again.
THIS PROGRAM HAS BEEN BLOCKED
TV-PG
BLOCKING IS ACTIVE
PLEASE ENTER PIN CODE
TO TEMPORARILY UN-BLOCK
_ _ _ _
L
V
EXCEEDS SET LIMITS
PUSH MUTE TO ENTER PIN
SELECT [0–9] END [EXIT]
Blocking unrated movies and programs
Some movies and programs are not rated. You can use the V-Chip
Control feature to block unrated movies and programs.
To block unrated movies and programs:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the Enter PIN Code screen.
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
6. Press y or z to highlight ENABLE BLOCKING.
(Continued on next page)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press x or • to highlight “Y,” which enables all blocking by
activating the V-Chip. (Note: Highlight “N” to deactivate the
V-Chip feature and disable blocking.)
8. Press y or z to highlight SET BLOCKING OPTIONS.
9. Press x or • to display the unrated movie/program blocking menu.
10. Press y or z to highlight BLOCK TV NONE RATING.
11. Press x or • to highlight “Y” to block movies/programs rated
“TV None.” (Note: Highlight “N” to unblock unrated programs.)
12. Press EXIT to return to normal TV viewing.
SET UP
SET UP
ENABLE BLOCKING
SET RATING
[Y] N
BLOCK MPAA UNRATED:
[Y] N
[Y] N
BLOCK TV NONE RATING:
BACK TO V-CHIP MENU
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
NOTICE: ENABLING THIS OPTION
MAY BLOCK EMERGENCY
MESSAGES
Caution:
VIDEO LOCK
OFF
[
Blocking unrated television programs (those
rated “TV NONE”) may block emergency
messages.
]
[
]
[
]
[
]
MOVE
SELECT
MOVE
SELECT
Blocking channels
You can block a maximum of four TV channels and four cable
channels. Blocked channels cannot be viewed, regardless of their
ratings. If you try to tune the TV to a blocked channel, the nearest
unblocked channel will display.
Note:
After programming CHANNEL BLOCK, tune
the TV to a channel that is not blocked before
turning the TV off.
To block a channel:
1. Tune the TV to the channel you want to block.
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight V-CHIP CONTROL.
5. Press x or • to display the Enter PIN Code screen.
POWER
LIGHT RECALL
TV
6. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
CABLE
VCR
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
4
7. Press y or z to highlight ENABLE BLOCKING.
CH
8. Press x or • to highlight “Y,” which enables all blocking by
activating the V-Chip Control feature. (Note: Highlight “N” to
deactivate the V-Chip feature and disable blocking.)
Channel
Numbers
9
7
VOL
CH RTN
9. Press y or z to highlight BLOCK CHANNEL.
ENT
100
10. Press x or • to display the BLOCK CHANNEL menu.
ADV/
PIP CH
MENU
MENU
SET/CLEAR will be highlighted.
.CAPT
C
11. Press x or • to highlight SET.
FAV
ENTER
FAV
12. Press z to add the current channel to the list.
RESET
EXIT
ADV/
PIP CH
EXIT
SET UP
BLOCK CHANNEL
[SET] CLEAR
0
0
0
6
[
]
[
]
SELECT
SET
END [EXIT]
13. Press MENU.
14. Press EXIT.
15. Repeat steps 1–14 to block additional channels.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
To unblock all blocked channels:
POWER
LIGHT RECALL
Note: This will unblock every channel you have blocked. You cannot
unblock individual channels.
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the Enter PIN Code screen.
2
5
8
0
3
6
1
4
CH
Channel
Numbers
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
9
7
VOL
CH RTN
ENT
100
6. Press y or z to highlight BLOCK CHANNEL.
ADV/
PIP CH
MENU
MENU
.CAPT
7. Press x or • to display the BLOCK CHANNEL menu.
C
SET/CLEAR will be highlighted.
FAV
ENTER
FAV
8. Press x or • to highlight CLEAR.
9. Press z to clear all blocked channels from the list.
10. Press MENU.
RESET
EXIT
ADV/
PIP CH
EXIT
11. Press EXIT to return to normal TV viewing.
Locking video inputs
You can use the Video Lock feature to block the input sources
(Video 1, Video 2, Video 3, and ColorStream) and channels 3 and 4.
Note: The Video Lock feature is independent of the Enable Blocking
option of V-Chip control (page 21).
Note:
The Video Lock options are:
In normal TV viewing, if you cannot access the
input sources (Video 1, Video 2, Video 3, and
ColorStream) or channels 3 and 4, check the
Video Lock setting and highlight OFF if
necessary.
Video: Blocks Video 1, Video 2, Video 3, and ColorStream.
Video+: Blocks Video 1, Video 2, Video 3, ColorStream, and
channels 3 and 4.
Off:
Disables the Video Lock feature.
To set up video lock:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight V-CHIP CONTROL.
4. Press x or • to display the Enter PIN Code screen.
5. Use the CHANNEL NUMBERS (0–9) to enter your four-digit
PIN code. After entering the code, the V-Chip Control menu
appears.
6. Press y or z to highlight VIDEO LOCK.
7. Press x or • to select the desired level of video locking (Video,
Video+, or Off).
SET UP
ENABLE BLOCKING [Y] N
SET RATING
SET BLOCKING OPTIONS
NEW PIN CODE
BLOCK CHANNEL
VIDEO LOCK
VIDEO VIDEO+ [OFF]
[
]
[
]
MOVE
SELECT
8. Press EXIT to return to normal TV viewing.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel labels
RECALL
POWER
LIGHT RECALL
You can assign labels to a maximum of 32 channels. Each channel
label can have a maximum of four characters.
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
For example, if channel 8 is your public television station, you could
create the label “PBS” for that channel. The label “PBS” would then
appear on-screen when you tune the TV to channel 8.
2
5
8
0
3
6
1
4
CH
Channel labels appear on-screen above the channel number every time
you turn the TV on, change the channel, or press RECALL.
Channel
Numbers
9
7
VOL
To create a channel label:
1. Tune the TV to the channel you want to label.
2. Press MENU.
CH RTN
ENT
100
ADV/
PIP CH
MENU
MENU
.CAPT
C
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight CH LABEL.
FAV
ENTER
FAV
RESET
EXIT
SET UP
ADV/
PIP CH
EXIT
MORE
V-CHIP CONTROL
FAVORITE CH
CH LABEL
VIDEO LABEL
TIMER:
DEMO:
0 MIN
START [STOP]
[
]
[
]
MOVE
START
5. Press x or • to display the CH LABEL menu. SET/CLEAR will
be highlighted.
6. Press x or • to highlight SET.
7. Press z to highlight LABEL.
SET UP
SET UP
CH LABEL
SET/CLEAR
CH LABEL
SET/CLEAR
LABEL
[SET] CLEAR
_ _ _ _
[SET] CLEAR
_ _ _ _
LABEL
SET UP MENU
SET UP MENU
[
]
[
]
MOVE
SET [ENT]
SELECT
[
]
[
]
MOVE
SELECT
8. Press x or • repeatedly to scan through the list of available
characters until the desired character appears in the first space.
9. Press MENU.
10. Repeat steps 8 and 9 to enter the rest of the characters.
Note: For a blank space in the label name, you must choose a
blank space from the list of characters; otherwise, a dash will
appear in the space.
11. Repeat steps 1–10 for up to 32 channels.
12. Press EXIT to return to normal TV viewing.
To erase a channel label:
1. Select the channel whose label you want to erase.
2. Press MENU.
3. Press x or • to highlight the SET UP menu.
4. Press y or z to highlight CH LABEL.
5. Press x or • to display the CH LABEL menu. SET/CLEAR will
be highlighted.
6. Press x or • to highlight CLEAR.
7. Press MENU.
8. Repeat steps 1–7 to erase other channel labels, or press EXIT to
return to normal TV viewing.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Video labels
POWER
LIGHT RECALL
The Video Label feature allows you to label each input source for your
TV, from the following preset list of labels:
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
–:
Uses the default label name
VCR: Video cassette recorder
DVD: Digital video disc or digital versatile disc
DTV: Digital TV set-top box
SAT: Satellite box
2
5
8
0
3
6
1
4
CH
9
7
VOL
CH RTN
CBL: Cable box
ENT
100
ADV/
PIP CH
To set up video labels:
1. Press MENU.
MENU
MENU
CAPT
.
C
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight VIDEO LABEL.
4. Press x or • to display the Video Label screen.
FAV
ENTER
FAV
RESET
EXIT
EXIT
ADV/
PIP CH
5. Press y or z to highlight the input source to be labeled
(VIDEO 1, VIDEO 2, VIDEO 3, or ColorStream).
6. Press x or • to select the desired label for that input source.
SET UP
VIDEO LABEL
VIDEO1
– VCR DVD DTV [SAT] CBL
VIDEO2
VIDEO3
ColorStream
–
–
–
SET UP MENU
[
]
[
]
MOVE
SELECT
7. Repeat steps 1–6 to label the other input sources.
8. When you finish setting up video labels:
• To return to the previous menu, press y or z to highlight
SET UP MENU, and then press x or •.
• To return to normal TV viewing, press EXIT.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching picture-in-picture (PIP)
The picture-in-picture (PIP) feature allows you to watch two pictures
at the same time. The small PIP window can display a signal from a
TV broadcast or an external source, such as a VCR.
Note:
The PIP window will not open when a
ColorStream (component video) source is
being viewed.
To display a TV broadcast in the PIP window:
1. Tune the TV to the program you want to watch in the main
window.
2. Press PIP to display a small picture (one press displays a PIP
window 1/9 the size of the screen; two presses display a 1/16-size
window).
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
4
CH
CH (Channel)
1/9 1/16
PIP
7
9
7
VOL
CH RTN
ENT
100
3. Press PIP CH yz to change the PIP channel. Press Channel yz
ADV/
PIP CH
MENU
to change the main channel.
.CAPT
C
To display an external source in the PIP window:
1. Connect the external equipment to the ANT-1 connection on
the TV.
FAV
ENTER
FAV
PIP CH
RESET
EXIT
Note: An ANT-2 source will not display as a PIP. For connection
ADV/
PIP CH
information, see “Connecting your TV” on page 7.
SOURCE
PIP
STOP SOURCE
PLAY PIP
2. Turn on the TV and select the program/source you want to watch
in the main window.
REC TV/VCR REW
FF
SWAP
3. Press PIP (one press to display a PIP window 1/9 the size of the
STILL LOCATE SWAP
screen; two presses to display a 1/16-size window).
4. Press SOURCE to select the PIP input source (TV, VIDEO 1,
VIDEO 2, or VIDEO 3). The current source will display
on-screen in green.
CT-9946
PIP
TV
VIDEO1
VIDEO2
VIDEO3
TO SELECT PUSH SOURCE
To turn PIP off:
Press PIP two or three times, depending on the PIP window size
you selected.
Switching the main and small pictures
With the TV in PIP mode, repeatedly press SWAP to switch the
main and small pictures back and forth.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the location of the PIP window
ADV/
With the TV in PIP mode, press LOCATE to change the location of
the PIP window on-screen. Every time you press LOCATE, the PIP
window changes position counter-clockwise.
PIP CH
MENU
CAPT
.
C
FAV
ENTER
FAV
PIP CH
RESET
EXIT
ADV/
PIP CH
SOURCE
PIP
STOP SOURCE
PLAY PIP
REC TV/VCR REW
FF
SWAP
STILL LOCATE SWAP
LOCATE
STILL
CT-9946
Freezing the PIP display
With the TV in PIP mode, press STILL to freeze the PIP display. The
PIP picture becomes still, and is outlined in red on-screen. Press
STILL again to restore the moving picture (outlined in green).
Still
Watching multi-window PIP
Note:
Multi-window PIP displays channels
programmed for the signal source you are
currently viewing (ANT-1 or Cable).
Multi-window PIP appears as six small boxes across the bottom of the
screen. The multi-window PIP displays only the channels you
programmed into the TV’s memory (see “Adding channels to the TV’s
memory” on page 17).
Note: The LOCATE, SWAP, PIP CHANNEL yz, SOURCE,
and STILL buttons do not function in multi-window PIP mode.
To view multi-window PIP:
Press PIP three times.
The TV cycles through all of the programmed channels, showing a
few seconds of each channel’s programming, and then freezes the
image and moves on to the next channel in a continuous cycle. The
channel number appears above each PIP window.
Note:
If V-Chip blocking is enabled when
you view multi-window PIP, channels
exceeding the rating limits will appear
14
23
27 30
43
56
X
as a black window with a red “X.”
To turn multi-window PIP off:
Press PIP again, or change the channel.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
Adjusting the picture quality
You can adjust the picture’s contrast, brightness, sharpness, color, and
tint. Your picture quality adjustments are stored automatically in the
TV’s memory. You can keep these settings or choose preset options in
the PREFERENCE menu (see “Selecting the color temperature”
below, and “Adjusting the picture preference” on the next page.)
yzx •
MENU
To adjust the picture quality:
POWER
LIGHT RECALL
1. Press MENU.
2. Press x or • to highlight the PICTURE menu.
3. Press y or z until the quality you want to adjust is highlighted.
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
4
CH
PICTURE
Note:
–
CONTRAST 50
BRIGHTNESS 50
SHARPNESS 50
COLOR
TINT
+
To reset the picture (and audio)
adjustments to the factory settings,
select RESET in the PICTURE menu.
9
7
VOL
50
0
CH RTN
ENT
100
RESET
[
]
[
]
MOVE
ADJUST
ADV/
PIP CH
MENU
MENU
.CAPT
C
4. Press x or • to adjust the level, as described in the following table:
FAV
ENTER
FAV
Selection
Pressing
Contrast
Brightness
Sharpness
Color
Lower
Higher
RESET
EXIT
Darker
Softer
Paler
Lighter
Sharper
Deeper
Greenish
ADV/
PIP CH
Tint
Reddish
Selecting the color temperature
You can change the picture quality by selecting from three preset color
temperatures—cool, medium, and warm—as described in the
following table:
Mode
Picture Quality
Cool
Medium
Warm
Blueish
Neutral
Reddish
To select the color temperature:
1. Press MENU.
2. Press x or • to highlight the PREFERENCE menu.
3. Press y or z to highlight COLOR TEMPERATURE.
4. Press x or • to highlight the mode you prefer.
PREFERENCE
COLOR TEMPERATURE
[COOL] MEDIUM WARM
PICTURE PREFERENCE
[SPORTS] STANDARD MOVIE MEMORY
[
]
[
]
MOVE
SELECT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture preference
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
You can select four picture modes—Sports, Standard, Movie, and
Memory—as described in the following table:
Mode
Picture Quality
Sports
Bright and dynamic picture (factory-set)
Standard picture quality (factory-set)
Standard
Movie
Memory
yzx •
MENU
Movie-like picture setting (factory-set)
Your personal preferences (set by you; see
“Adjusting the picture quality” on page 30.)
To select your picture preference:
1. Press MENU.
2. Press x or • to highlight the PREFERENCE menu.
3. Press y or z to highlight PICTURE PREFERENCE.
4. Press x or • to highlight the mode you prefer.
RECALL
TIMER
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
4
CH
PREFERENCE
9
7
COLOR TEMPERATURE
[COOL] MEDIUM WARM
VOL
CH RTN
PICTURE PREFERENCE
[SPORTS] STANDARD MOVIE MEMORY
ENT
100
ADV/
PIP CH
MENU
MENU
[
]
[
]
.CAPT
MOVE
SELECT
C
FAV
ENTER
FAV
Displaying on-screen information
RESET
Press RECALL to display the following information on-screen:
• Antenna mode (when in TV mode)
• Channel number or video mode
EXIT
EXIT
ADV/
PIP CH
• Channel label (if set)
• Audio status (stereo or SAP)
• Rating of current program (if rated)
Setting the off timer
The off timer turns the TV off automatically.
To set the off timer:
1. Press TIMER.
2. Press • to increase (or x to decrease) the amount of time until the
TV turns off automatically (in 10-minute increments, to a
maximum of 180).
3. Press EXIT to exit the menu and return to normal TV viewing.
To cancel the off timer:
Set the off timer to 0 (zero) minutes in step 2 above, or turn the
TV off and then on again.
Auto power off
The TV turns itself off automatically after approximately 15 minutes if
it is tuned to a vacant channel or a station that stops broadcasting for
the day.
Note: The auto power off feature does not work in VIDEO mode.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the closed caption feature
The Closed Caption feature has two options:
POWER
LIGHT RECALL
• Captions—An on-screen display of the dialogue, narration, and
sound effects of programs and videos that are closed-captioned
(usually identified in your local TV listing as “CC”).
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
• Text—An on-screen display of information not related to the
program, such as weather or stock data (if available in your
viewing area).
2
5
8
0
3
6
1
4
CH
To view captions or text:
1. Tune the TV to the desired program.
9
7
VOL
CH RTN
ENT
100
2. Press C.CAPT (or press MENU, and then press x or • to
C.CAPT
MENU
highlight the CLOSED CAPTION menu).
ADV/
PIP CH
MENU
.CAPT
3. Press y or z to highlight CC.
C
FAV
ENTER
FAV
CLOSED CAPTI0N
RESET
CC:
C1 C2 C3 C4 T1
T2 T3 T4 [OFF]
EXIT
ADV/
PIP CH
[
]
[
]
MOVE
SELECT
Note:
4. Press x or • to select the desired Closed Caption mode, as
A closed caption signal may not display in the
following situations:
follows:
• To view captions, select C1, C2, C3, or C4 (C1 displays
translation of the primary language in your area). Note: If the
program or video you selected is not closed-captioned, no
captions will display on the screen.
•
•
•
When a videotape has been dubbed
When the signal reception is weak
When the signal reception is non-
standard
The top of the mountain is covered
with snow all the year round.
• To view text, select T1, T2, T3, or T4. Note: If text is not
available in your viewing area, a black rectangle may appear on
your screen. If this occurs, turn the Closed Caption feature off.
WORLD WEATHER
Temps
F
Current
Weather
Clear
C
LONDON
MOSCOW
PARIS
51
11
14
12
19
18
57
Cloudy
Clear
53
66
ROME
TOKYO
Cloudy
Rain
65
• To turn the Closed Caption feature off, highlight OFF in the
Closed Caption menu.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound
RECALL
MUTE
POWER
LIGHT RECALL
Muting the sound
TV
CABLE
VCR
Press MUTE to temporarily turn off the sound. While the sound is off,
the screen displays the word “MUTE” in the lower /right corner. To
restore the sound, press MUTE or VOLUME yz.
When you press MUTE, the Closed Caption feature is automatically
activated. To deactivate captions and restore normal sound, press
MUTE again. This feature works only when the Closed Caption mode
is set to OFF. See “Using the closed captioned feature” on page 40 for
more information about closed caption settings.
MUTE TV/VIDEO TIMER
2
5
8
0
3
6
1
4
CH
9
7
VOL
VOL
CH RTN
ENT
100
Selecting stereo/SAP broadcasts
ADV/
PIP CH
MENU
MENU
.CAPT
The multi-channel TV sound (MTS) feature provides high-fidelity
stereo sound. MTS also can transmit a second audio program (SAP)
containing a second language or other audio information.
Note: The MTS feature is not available in VIDEO mode.
C
FAV
ENTER
FAV
RESET
In general, you can leave your TV in stereo mode because the TV
automatically outputs either stereo or monaural (“mono”) sound,
depending on the broadcast type.
EXIT
ADV/
PIP CH
When the TV receives a stereo or SAP broadcast, the word “STEREO”
or “SAP” displays on the screen every time you turn the TV on,
change the channel, or press RECALL.
To listen to stereo sound:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight MTS.
4. Press x or • to highlight STR (stereo).
Note: If the stereo sound is noisy, select MONO to reduce the
noise.
AUDIO
MTS:
[STR] SAP MONO
50
50
0
BASS
TREBLE
BALANCE
SURROUND: [ON] OFF
AUDIO OUT: [FIX] VARIABLE
MORE
[
]
[
]
MOVE
SELECT
To listen to a second audio program (SAP):
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight MTS.
4. Press x or • to highlight SAP. The TV speakers will output only
the second audio program.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound quality
You can change the sound quality of your TV by adjusting the bass,
treble, and balance.
Note:
To reset the audio adjustments (bass, treble,
and balance) to the factory settings, select
RESET in the PICTURE menu (see page 30).
To adjust the sound quality:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight the quality you want to adjust.
4. Press x or • to adjust the level:
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
• x makes the sound quality weaker or decreases the balance in
the right channel, depending on the item selected.
• • makes the sound quality stronger or decreases the balance in
the left channel, depending on the item selected.
yzx •
MENU
POWER
LIGHT RECALL
AUDIO
TV
MTS:
[STR] SAP MONO
–
CABLE
VCR
+
BASS
TREBLE
BALANCE
50
50
0
MUTE TV/VIDEO TIMER
SURROUND: [ON] OFF
AUDIO OUT: [FIX] VARIABLE
MORE
2
5
8
0
3
6
1
4
[
]
[
]
MOVE
ADJUST
CH
Using the surround sound feature
9
7
VOL
CH RTN
The surround sound feature expands the audio listening field wider and
deeper to create exceptional sound quality from the TV speakers.
This feature uses stereo signals from a TV broadcast or video input.
ENT
100
ADV/
PIP CH
MENU
MENU
.CAPT
C
To turn the surround sound feature on:
1. Press MENU.
FAV
ENTER
FAV
2. Press x or • to highlight the AUDIO menu.
RESET
3. If you have not already done so, select STEREO mode (press y or
EXIT
ADV/
PIP CH
z to highlight MTS, and then press x or • to highlight STR).
4. Press y or z to highlight SURROUND.
5. Press x or • to highlight ON.
AUDIO
MTS:
[STR] SAP MONO
BASS
TREBLE
BALANCE
50
50
0
SURROUND: [ON] OFF
AUDIO OUT: [FIX] VARIABLE
MORE
[
]
[
]
MOVE
SELECT
To turn the surround sound feature off:
Highlight OFF in step 5 above. Note: In general, you can leave the
surround sound feature on because it automatically outputs surround
stereo or monaural sound, depending on the broadcast or video type.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting variable audio OUT
If you connect external audio equipment (such as a stereo
audio amplifier or surround sound system) to the TV’s Audio OUT
jack, you can use the AUDIO OUT feature to select either variable or
fixed audio output.
MENU
TV / VIDEO
VOLUME
CHANNEL
POWER
– If you set AUDIO OUT to VARIABLE, you can use the volume
controls on either the TV or the audio equipment to adjust the
sound level coming through the audio equipment.
yzx •
MENU
– If you set AUDIO OUT to FIX, you must use the volume controls
on the audio equipment to adjust the sound level coming through
the audio equipment (the TV’s volume setting will have no effect).
POWER
LIGHT RECALL
Note: Fixed audio output provides a cleaner signal than variable audio
output.
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
See page 11 for details on connecting an audio amplifier to the TV’s
Audio OUT jack.
2
5
8
0
3
6
1
4
To select variable audio output:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight AUDIO OUT.
4. Press x or • to highlight VARIABLE.
CH
9
7
VOL
CH RTN
ENT
100
ADV/
PIP CH
MENU
MENU
CAPT
.
C
AUDIO
MTS:
BASS
TREBLE
BALANCE
[STR] SAP MONO
FAV
ENTER
FAV
50
50
0
SURROUND: [ON] OFF
RESET
AUDIO OUT: FIX [VARIABLE]
MORE
EXIT
ADV/
PIP CH
[
]
[
]
MOVE
SELECT
To select fixed audio output:
1. Highlight FIX in step 4 above.
Turning off the built-in speakers
Use this feature to turn off the TV’s built-in speakers when you
connect external speakers to your TV (see “Connecting an audio
amplifier” on page 11).
To turn off the built-in speakers:
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight SPEAKERS.
4. Press x or • to highlight OFF.
AUDIO
MORE
SPEAKERS: ON [OFF]
SBS:
SBS LEVEL:
[ON] OFF
50
[
]
[
]
MOVE
SELECT
To turn on the built-in speakers:
1. Highlight ON in step 4 above.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the sub-bass system (SBS)
The sub-base system (SBS) allows you to enhance bass performance,
even when the volume is low.
RECALL
POWER
POWER
LIGHT RECALL
TV
CABLE
VCR
MUTE TV/VIDEO TIMER
To turn the sub-bass system on (or off):
1. Press MENU.
2. Press x or • to highlight the AUDIO menu.
3. Press y or z to highlight SBS.
4. Press x or • to highlight ON (or OFF).
2
5
8
0
3
6
1
4
CH
9
7
VOL
CH RTN
ENT
100
AUDIO
ADV/
PIP CH
MENU
MENU
MORE
SPEAKERS:
[ON] OFF
.CAPT
C
SBS:
SBS LEVEL:
[ON] OFF
50
FAV
ENTER
FAV
[
]
[
]
MOVE
SELECT
RESET
EXIT
EXIT
ADV/
PIP CH
To adjust the sub-bass system:
1. Turn the sub-bass system on, as instructed above.
2. Press MENU.
3. Press x or • to highlight the AUDIO menu.
4. Press y or z to highlight SBS LEVEL.
5. Press x or • to adjust the SBS level.
AUDIO
MORE
SPEAKERS:
SBS:
[ON] OFF
[ON] OFF
–
+
SBS LEVEL: 50
[
]
[
]
MOVE
ADJUST
Viewing the demonstration (DEMO) mode
The demonstration (DEMO) mode is an option available on the
SET UP menu that will demonstrate several features of your TV.
To start the demonstration mode:
1. Press MENU.
2. Press x or • to highlight the SET UP menu.
3. Press y or z to highlight DEMO.
4. Press x or • to highlight START.
4. Press MENU to start the demo.
To stop the demonstration mode:
Press RECALL, EXIT, or POWER.
Understanding the last mode memory feature
If the power is cut off while you are viewing the TV, the Last Mode
Memory feature turns the TV on automatically when the power is
resupplied.
If the power is going to be off for a long time and you are going to be
away from your TV, unplug the power cord to prevent the TV from
turning on in your absence.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling a service technician, please check the following table for possible causes of the problem and
some solutions.
Problem
Solution
TV will not turn on
• Make sure the power cord is plugged in, and then press POWER.
• The remote control batteries may be dead. Replace the batteries or
press the POWER button on the TV.
No picture, no sound
No sound, picture OK
• Check the antenna/cable connections.
• The sound may be muted. Press MUTE or VOLUME y z.
• The station may have broadcast difficulties. Try another channel.
Poor sound, picture OK
Poor picture, sound OK
• The station may have broadcast difficulties. Try another channel.
• Check the antenna connections.
• The station may have broadcast difficulties. Try another channel.
• Adjust the PICTURE menu.
Poor reception of broadcast channels
• The station may have broadcast difficulties. Try another channel.
• Check the antenna connections.
• If you are using a VCR, make sure the TV/VCR button is set
correctly.
Cannot receive above channel 13
Unable to select a certain channel
• Make sure TV/CABLE is set to TV mode.
• The channel may be locked out with the channel lock feature, or
erased with the add/erase feature.
Multiple images
• The station may have broadcast difficulties. Try another channel.
• Use a highly directional outdoor antenna.
Poor color or no color
• The station may have broadcast difficulties. Try another channel.
• Adjust the TINT and/or COLOR in the PICTURE menu.
• If you change the direction of the TV while it is turned on, the
picture could suffer from color shading. If so, turn the TV off and
allow it to cool down for several hours before turning it on again.
No stereo or SAP sound from a
known MTS broadcast
• Make sure the MTS feature is set properly.
The remote control does not operate
• Check that the TV/CABLE/VCR switch is properly set.
• There may be an obstruction between the remote control and the
remote control sensor.
• The remote control batteries may be dead. Replace the batteries.
The V-Chip PIN code does not work
• Change or reset your PIN code.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
WARNING: TV sets use high voltage. Do not remove the cabinet back.
Refer all servicing to a qualified service technician.
To clean the TV screen and cabinet:
1. Unplug the power cord to avoid possible shock hazard.
2. Use a clean cellulose sponge or chamois cloth dampened with a solution of mild detergent and warm water
to clean the TV screen and trim. Do not use too much water; liquid spilling into the cabinet can damage
the TV.
3. Wipe off excess moisture with a clean dry cloth.
4. Polish the cabinet with a quality furniture polish to maintain the finish and appearance of the cabinet.
Caution:
Never use strong solvents such as thinner, benzene, or other chemicals on or near the cabinet.
These chemicals can damage the cabinet’s finish.
Specifications
Television system
Channel coverage
NTSC standard
VHF:
UHF:
2 through 13
14 through 69
Cable TV: Mid band (A-8 through A-1, A through 1)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 125)
Power source
120 AC, 60 Hz
Power consumption
Audio power
96 W
5 W + 5 W
Speaker type
2-3/8 x 4-3/4 inches (60 x 120 mm)
Video/Audio terminals
ColorStream™ (component video) INPUT
Y: 1V (p-p), 75 ohm
C
R
(PR): 0.7 V (p-p), 75 ohm
(PB): 0.7 V (p-p), 75 ohm
CB
S-VIDEO INPUT
Y-INPUT: 1 V (p-p), 75 ohm, negative sync.
C-INPUT: 0.286 V (p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUT
VIDEO: 1 V (p-p), 75 ohm, negative sync.
AUDIO: 150 mV (rms) (30% modulation equivalent, 47 k ohm)
VIDEO/AUDIO OUTPUT
VIDEO: 1 V (p-p), 75 ohm, negative sync.
AUDIO: 150 mV (rms) (30% modulation equivalent, 47 k ohm)
Dimensions
Width: 38-3/16 inches (970 mm)
Height: 30-1/16 inches (764 mm)
Depth: 25-1/4 inches (641 mm)
Weight
154 lbs (69.9 kg)
Supplied accessories
Optional TV stand
Remote control with two size “AA” batteries
ST-3641
Design and specifications are subject to change without notice.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited United States warranty
Toshiba America Consumer Products, Inc. (“TACP”) and Toshiba Hawaii Inc. (“THI”) make the following limited warranties. These limited warranties extend
to the original consumer purchaser or any person receiving this set as a gift from the original consumer purchaser and to no other purchaser or transferee.
Limited One (1) Year Warranty
Owner’s Manual and Demographic Card
TACP and THI warrant this product and its parts against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. During this period, TACP and THI will repair or
replace a defective part, at their option, with a new or refurbished part,
without charge to you. TACP/THI Authorized Service Center personnel
will come to your home when warranty service is required. Depending on
the type of repair required, either the service will be performed in your
home or the set will be taken to the TACP/THI authorized service center
for repair and returned to your home at no cost to you.
You should read this owner’s manual thoroughly before operating this
product. You should complete and mail the enclosed Demographic card
within ten days after you, or the person who has given you this product as a
gift, purchased this product. This is one way to enable TACP/THI to
provide you with better customer service and improved products. Failure to
return the Demographic card will not affect your rights under this warranty.
Your Responsibility
The above warranties are subject to the following conditions;
(1) You must retain your bill of sale or provide other proof of purchase.
Limited Two (2) Year Warranty of Picture Tube
(2) All warranty servicing of this product must be made by an Authorized
TACP/THI Service Center.
TACP and THI further warrant the picture tube in this product against
defects in materials or workmanship for a period of two (2) years after the
date of original retail purchase. During this period, TACP and THI will
repair or replace a defective picture tube at their option, with a new or
refurbished picture tube, without charge to you, except that, if a defective
picture tube is replaced after one (1) year from the date of the original
retail purchase, you pay labor charges involved in the replacement.
(3) These warranties are effective only if the product is purchased and
operated in the U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment of
customer controls, and installation or repair of antenna systems are
not covered by this warranty. Reception problems caused by
inadequate antenna systems are your responsibility.
Rental Units
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any product or parts that have
been lost or discarded by you, or to damage to products or parts
caused by misuse or accident, damage caused by Acts of God such as
lightning or fluctuations in electric power, improper installation,
improper maintenance, or use in violation of instructions furnished by
us, or to units which have been modified or had the serial number
removed, altered, defaced, or rendered illegible.
The warranty for rental units begins with the first rental or thirty (30) days
from the date of shipment to the rental firm, whichever comes first.
Commercial Units
Products sold and used for commercial use have a limited ninety (90) day
warranty for all parts, labor and picture tube.
How to Obtain Warranty Service
If after following all of the operating instructions in this manual and checking the “Troubleshooting” section, you find that service is needed:
(1) To find the nearest Toshiba Authorized Service Center, visit
Solutions,” or call us toll-free at 1-800-631-3811.
(2) Present your bill of sale or other proof of purchase to the Authorized Service
Center. “Authorized TACP/THI service center personnel will come to your
home when warranty service is required. Depending on the type of repair
required, either the service will be performed in your home or the TV set will
be taken to the TACP/THI authorized service center for repair and returned to
your home at no cost to you.”
In Hawaii, contact Toshiba Hawaii, Inc., Service, 327
Kamakee Street, Honolulu, HI 96814, (808) 591-9281.
For additional information, visit our web site:
All warranties implied by state law, including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the
duration of the limited warranties set forth above. With the exception of any warranties implied by state law as hereby limited, the foregoing warranty is
exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or
replacement of any parts. In no event shall TACP or THI be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever. The
time within which action must be commenced to enforce any obligation of TACP or THI arising under this warranty or under any state or law of the
United States or any state thereof, is hereby limited to 90 days from the date you discover, or should have discovered, the defect. This limitation does not
apply to implied warranties arising under state law.
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. Some states do not allow limitation on
how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages; therefore, the
above provisions may not apply to you.
ATTENTION CANADIAN CONSUMERS
Canadian consumers are requested to complete the special Canadian “Warranty Registration Form” enclosed, and
forward this completed form with a copy of the bill of sale to TOSHIBA OF CANADA to “Register and Validate” their
warranty.
Products purchased in the U.S.A. and used in Canada are not covered by these warranties.
Products purchased in Canada and used in the U.S.A. are not covered by these warranties.
REV. 03/01
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Toshiba America
Consumer Products, Inc.
Head Office
National Service Division
82 Totowa Road
Wayne, NJ 07470
1420B Toshiba Drive
Lebanon, TN 37087
Head Office
Toshiba Hawaii, Inc.
327 Kamakee Street
Honolulu, HI 96814
Toshiba of Canada, Ltd.
Head Office
Service Centers
191 McNabb Street
Markham, Ontario L3R 8H2
Canada
Toronto
191 McNabb Street
Markham, Ontario L3R 8H2
Canada
Tel: (905) 470-5400
Montreal
1643 North Service Road
Trans-Canada Highway
Dorval, Quebec H9P 1J1
Canada
Tel: (514) 856-4100
Vancouver
22171 Fraserwood Way
Richmond, British Columbia V6W 1J5
Tel: (604) 303-2500
Manufactured by:
Toshiba America
Consumer Products, Inc.
PRINTED IN USA
(01-04)B
23565245
Download from Www.Somanuals.com. All Manuals Search And Download.
|