TOPFIELD
The User’s Manual
FREE TO AIR
Digital Satellite Receiver
- Non-SCART model
TF3000Fi
- SCART model
TF3000FEi
Please read this User s Manual carefully.
The menu structure and specification can be changed without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING Warning WARNING Warning WARNING
Please read the following recommended safety precautions carefully for your safety.
MAINS SUPPLY :
90-250V AC 50/60 Hz.
OVERLOADING : Do not overload wall outlets, extension cords or adapters
as these can result in fire or electrical shock.
LIQUIDS :
Keep liquids away from the STB.
The apparatus shall not be exposed to dripping or splashing and
that no objects filled with liquids, such as vases, shall be placed
on the apparatus.
SMALL OBJECTS : Coins or other small objects must be kept away from the IRD
as they can fall through the ventilation slots of the IRD and
cause serious damage.
CLEANING :
Disconnect the IRD from the wall socket before cleaning it.
Use a dry cloth lightly dampened(no solvents) to clean
the exterior of the IRD.
VENTILATION :
Do not block the decoder’s ventilation slots.
Ensure that a free airflow is maintained around the IRD.
NEVER stand the IRD on soft furnishings or carpets.
Do not use or store the IRD where it is exposed to direct
sunlight or near a heater. NEVER stack other electronic
equipment on top of the IRD.
ATTACHMENTS : Do not use any attachments that are not recommended as these
may cause hazards or damage the equipment .
CONNECTION TO THE SATELLITE DISH LNB :
Disconnect the IRD from the mains before connecting or
disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB,
SERVICING :
Do not attempt to service this product yourself.
Refer all serving to qualified service agents.
LIGHTNING :
It is recommended that the IRD should remain connected at all
times to the mains supply and satellite dish (except when
working on the LNB). However, the manufacturer’s
instructions for safeguarding other equipment connected to the
IRD, i, e, TV set, must be followed during lightning storms.
LNB and the modem telephone line are essential.
EARTHING :
The LNB cable must be earthed to the system earth for
the satellite dish.
LOCATION :
Locate the IRD indoor place properly to prevent lightening,
raining and direct sunlight.
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing the Digital Satellite Receiver (STB).
This Digital Satellite Receiver is fully compliant with the international DVB
standard and thus transmits digital images, sounds, information guides and teletext
directly to your TV through the satellite. Now you can comfortably see and receive
digitally transmitted music, news, movie and sports satellite broadcasts in your office
or at your home.
In the Channel Search section, both the automatic channel search method and the
manual Search mode are provided. Also it supports DiSEqC 1.2, enabling you to move your
antenna in order to focus your preferred satellite. You can save up to 3500 TV and 1500
Radio channels and work around with the Favorite, Lock, Delete, Move and Sort
functions. The Menu is very modern and supports different languages.
All functions can be carried out using the remote control and some of the functions can
also be carried out using the front panel.
The STB is easy to use and adaptable for future advances. Please be aware that new
software may change the functions of the STB.
If you have any difficulties concerning the operation of your STB, please refer to the
relevant section of this manual, including the ‘Troubleshooting’. This Manual will
provide you with useful information on using the STB.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Please ensure that the following items are included with the STB.
1) Remote control unit
2) Batteries (size AAA)
3) User’s Guide (this document)
FEATURES
Fully Compliant to DVB
Antenna/LNB control
- 22KHz mode On/Off
- 0/12V mode selection (Non-SCART model only)
- Automatic FEC Detection
- DiSEqC 1.0 & 1.2 compatible
Satellite/Channel support
- 3500 TV channels, 1500 Radio channels storable
Video/Audio
- Automatic PAL/NTSC selection
- Multi-lingual Audio support
- Automatic channel search
OSD (On Screen Display) support
- 256 color support.
- Multi-lingual menu text support.
- GMT and Time Offset support
- 10 favorite channel groups support
- Page Up/Page Down available on your channel list
- PIG ( Picture In Graphic ) support
Teletext
- Software emulation mode with always VBI insertion mode on.
Games are embedded.
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT / REAR PANELS
- LED
TV / SAT
1) Front Panel
REMOTE
STANDBY
- CHANNEL
The channel buttons are to change channels.
- STANDBY
The power button of STB (ON / Stand by)
2)Rear Panel
(Non-SCART model)
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT / REAR PANELS
VIDEO INPUT
Video input
LNB IN
Connects the satellite antenna cable.
AUDIO-RIGHT INPUT
Audio input.(RED)
LNB OUT
Use it to connect to another STB.
AUDIO-LEFT INPUT
Audio input.(WHITE)
RS232
Upgrades the STB Program & software
0/12V OUTPUT
VIDEO OUTPUT
Video output
Chooses the LNB on the antenna.
RF OUT
AUDIO-RIGHT OUTPUT
Audio output.(RED)
Connects the TV RF IN (ANT IN)
RF IN
AUDIO-LEFT OUTPUT
Audio output.(WHITE)
Connects the TV antenna
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT / REAR PANELS
(SCART model)
AUDIO-LEFT OUTPUT
Audio output.(WHITE)
LNB IN
Connects the satellite antenna cable.
AUDIO-RIGHT OUTPUT
Audio output.(RED)
LNB OUT
Use it to connect to another STB.
RS232
Upgrades the STB Program & software
TV SCART
Connects the TV SCART
VCR SCART
Connects the VCR SCART
VIDEO OUTPUT
Video output
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL UNIT (RCU)
Switches the STB between Operation and
Standby mode.
Returns to the previous menu and the screen.
Enables/ Disables the Audio.
CH
OK
/LIS T
VOL
VOL
Selects the TV or Radio service channels
CH
and individual
menu options.
Displays the Menu on screen or returns to
previous menu from submenu.
Displays the EPG (Electronic Program
Guide) on screen only when available.
CH
CH
Tunes to the next or previous service.
Services up or down through the available
services.
VOL
VOL
Adjusts the volume (Increase/Decrease).
Displays Channel List on screen. Selects the item in the menu mode.
Displays the program information box on the screen and removes it.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL UNIT (RCU)
Selects the previously viewed channel.
Selects the TV/Radio mode.
Changes the terrestrial TV and Satellite mode.
Selects LEFT/RIGHT/MONO/STEREO sound function.
Selects the subtitle language list for the current service.
Enables the teletext with software emulation.
Displays the favorite channel list.
Displays and alters the UHF setting in menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (Connection)
First, connect both the satellite antenna and the TV line to the STB and switch the
power on.
In this manual there are some of the most common ways to connect the equipment:
TV, VCR and STB.
There are several ways of connecting the STB to the existing Audio/TV system.
We recommend using one of the following setups.
If you have problems with your connections and need help, contact your dealer or
Service Provider.
1.Non-SCART model
1) Connection to TV, VCR and Hi-Fi
1-1) Connection to the TV with the CINCH
Cable.
Connect one end (3 connectors) of the
CINCH cable to the AUDIO-RIGHT
(red), AUDIO-LEFT (white) and
the VIDEO OUTPUT (yellow) socket
on the STB.
Connect the other end (3 connectors) to
the AUDIO-RIGHT input (red),
AUDIO-LEFT input (white), and the
VIDEO input (yellow) socket on the TV or Hi-Fi.
1-2) Connection to the TV using the RF cable.
Connect a terrestrial antenna to RF IN socket on
the STB.
Connect one end of the RF cable to the
RF OUT socket on the STB. Connect
the other end to the ANT IN socket on the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (Connection)
1-3) Connection to the other A/V equipment with
the CINCH Cable.
Connect one end (3 connectors) of the CINCH
cable to the AUDIO-RIGHT-IN (red), AUDIO-
LEFT-IN (white) and the VIDEO INPUT
(yellow) socket on the STB.
Connect the other end (3 connectors) to the
AUDIO-RIGHT (red), AUDIO-LEFT
(white) and the VIDEO OUTPUT socket
on the A/V equipment. Then STB may bypass
the A/V signals of the A/V equipment in the
case of stanby mode of STB.
2) Connection to the other Satellite
Receiver.
Connect the satellite cable to the LNB IN
socket on the STB. With a connector, connect
the LNB OUT socket on the STB and the
ANT IN socket of the other STB.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (Connection)
2. SCART model
1) Connection to TV, VCR and Hi-Fi
1-1) Connection to the TV with the SCART
Cable.
Connect one end of the SCART cable to
the TV SCART socket on the STB and
the other end to a SCART socket on the
TV.
1-2) Connection to the VCR with the SCART
Cable.
Connect one end of the SCART cable to
the VCR SCART socket on the STB and
the other end to a SCART socket on the
VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (Connection)
1-3) Connection to the TV with the CINCH
Cable.
Connect one end (3 connectors) of the
CINCH cable to the AUDIO-RIGHT
(red), AUDIO-LEFT (white) and
the VIDEO OUTPUT (yellow) socket
on the STB.
Connect the other end (3 connectors) to
the AUDIO-RIGHT input (red),
AUDIO-LEFT input (white) and the
VIDEO input (yellow) socket on the
TV or Hi-Fi.
2) Connection to the other Satellite
Receiver.
Connect the satellite cable to the LNB IN
socket on the STB. With a connector, connect
the LNB OUT socket on the STB and the
ANT IN socket of the other STB.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Press the P o we r
button to operate the STB from the STANDBY mode.
Now, the Info box will appear for a given time and disappear. Pressing the
button,
the Info box will remain on the screen. The display time of the Info box is adjustable
under the In s ta lla tio n Menu of the Ma in Menu.
If the current broadcast has EPG (Electronic Program Guide) with it, press the
button
to see not only the current channel’s but also other channel’s EPG without any time constraints.
Also, press the button to reserve and save the current service and to watch the broadcast
automatically when it starts.
IMPORTANT: Before taking charge of your new STB, some important technical
settings are essential.
- Adjust your antenna through Dish Setting menu in installation menu.
- First, press the
button on the RCU to make the Ma in Menu appear.
- Go to the LNB S e ttin g menu under the C h a n n e l S e a rc h item of the
In s ta lla tio n menu and press
button.
- The Default PIN CODE is 0 0 0 0.
- Choose the right parameters for Satellite Name, LNB Frequency, 22KHz, 12 V,
DiSEqC 1.0, and Motorized System according to your LNB and satellite settings.
If the right Satellite Name and LNB Frequency were not found in the list, call the
dealer for satellite information.
- Then, press the
button and go back to the C h a n n e l S e a rc h menu.
- Set the S e a rc h Mo d e to the Au t o mode. (A Ma n u a l or Ad va n c e d S e a rc h
can always be performed later on)
- Select the S ta rt S e a rc h ... item and press
button.
button when the searching
- The search procedure will take a while. Press the
process is over (100%) to confirm and save the new channel list.
- For further information, please refer to the LNB S e ttin g item of the MENU
OPERATIONS on this manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Guide
Information Box
Press INFO key on the RCU to see the program
information. The Information box displays as
follows:
Channel Number
Channel Name
Detailed Program Information
Signal Level & Quality
Satellite Information
Information of subtitle and / or teletext
EPG (Electronic Program Guide)
To use currently showing TV, and Radio
services as well as to use next program
schedules, press
button on the
remote control unit.
If EPG is available on programs, you will see
the detailed description of the programs,
start/end time and programs schedules etc.
,
and
to move program and to see next program
button makes the reservation for the next program.
button shows extended information of the current program.
,
buttons will be used
schedules. The
button will change the contents of EPG between TV and Radio services.
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Guide
Subtitle
You can choose a language of subtitle using
button on the RCU.
If a broadcaster provides subtitles, you can see
symbol in the Information Box.
Teletext
If a broadcaster supports teletext, you can see
symbol in the Information Box.
There are VBI insertion mode and software emulation mode in teletext.
In the VBI insertion mode, which is always on, you can watch the teletext with your TV
using the RCU of your TV. To watch teletext with VBI insertion, your TV must support
teletext.
In the software emulation mode, you can watch the teletext even though your TV does
not support teletext. You can watch the teletext using the RCU of STB.
Press
Press
button twice to watch the teletext with software emulation mode.
button or E XIT(
) button to escape from teletext.
Soundtrack
You can choose a language of soundtrack using
button on the RCU when a broadcaster
S ound Track
AUTO
Track 01
Track 02
Track 03
Track 04
Track 05
Track 06
Track 07
Track 08
supports various languages of soundtrack.
Also, it is possible to choose a mode among
S te re o, Mo n o, Le ft and R ig h t using the
S ound Mod e
Mono
,
buttons on the RCU.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
Now this chapter assumes that the STB system has been installed correctly,
meaning:
* The satellite dish for the STB has been installed, connected to the STB and
correctly adjusted to the proper satellite.
* The STB is connected to the TV.
* The RCU has batteries and ready to control the STB.
If the STB has not been installed or connected properly, please refer to the
INS TALLATIO N (connection) menu on this manual.
Many of the functions of the STB are available from the Ma in Menu. Press the
button to open it.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
I. SYSTEM SETTING
I-1 TIME SETTING
Various time modes can be set, such as the current local time, the Power
On/Off time and the Sleep Time. The exact local present time can be adjusted
by using the G MT, the Tim e O ffs e t and the Mo d e sub menus.
PLEASE NOTE: Configure the L o c a l T i m e before adjusting the
W a k e u p T i m e P o w e r O f f T i m e
S l e e p T i m e
,
or the
.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
A. Local Time Setting
Press the
button in the Tim e S e ttin g Menu to open the Lo c a l Tim e
S e ttin g menu. Inside the Lo c a l Tim e S e ttin g menu, there are 4 sub menus:
Mo d e, Lo c a l Tim e,G MT and Tim e O ffs e t.
Mode
Using the
,
buttons can control the Au t o/Ma n u a l mode. The Au t o
mode automatically updates the time settings by adding the GMT received from
the satellite and the Tim e O ffs e t value you have inserted. The Au t o mode is
recommended.
Local Time
The Lo c a l Tim e is adjustable only when the Mo d e is on the Ma n u a l mode.
Adjust the current time, if necessary, by using the numeric buttons and the
buttons.
,
GMT
GMT is referred to the standard time of Greenwich. This cannot be changed.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
Time Offset
The current time of the local area can be inserted. In another words, insert the
time difference of the local time zone from the GMT. For example, if the local
area is Seoul (the time difference from the GMT being 9), insert 9 :0 0. The time
is adjustable by using the
,
buttons,15 minutes at a time.
B. Timer
Use the
,
buttons when selecting the O n/O ff mode. If the T im e r menu
Timer menu is set to O n, the Wa ke u p Tim e Menu, the Wa ke u p c h a n n e l
Menu and the P o we r O ff Tim e Menu becomes adjustable.
C. Wakeup Time
The Wa ke u p Tim e menu sets up the time the STB automatically turns on.
Insert the preferable Wa ke u p Tim e by using the numeric buttons and the
,
buttons on the RCU. Otherwise, make the T im e r disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
D. Wakeup Channel
The Wa ke u p C h a n n e l menu automatically turns the STB to the preset
channel when it automatically turns on by the Wa ke u p Tim e function.
E. Power Off Time
The P o we r O ff Tim e menu sets the time of the STB automatically turns off.
F. Sleep Time
The Sleep Tim e m e n u is similar to the P o we r O ff menu. The S le e p Tim e
function turns off after the adjusted sleep time.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
I-2. PARENTAL CONTROL
The age rating control, the PIN(Personal Identification Number) Code and the
passwords to various menus can be configured. The PIN Code box will
automatically appear when this menu is selected. The default PIN Code is 0 0 0 0.
A. Censorship
The C e n s o rs h ip menu blocks programs according to each specific setting.
Use the
,
buttons to select the menus below.
No Blo c k: Access to everyone.
4 ~1 8 (a g e ): Inaccessible for viewers within each minimum age limit.
To ta l Blo c k: Access to no one .
If the channel is limitation free, the block function will not work.
B. Change PIN Code
Go to the P IN C o d e menu to configure new PIN Code. Press the
button,
and a number box will appear on the right side of the screen. Enter the PIN
code by using the numeric buttons on your RCU.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
C. Access Control
The Ac c e s s C o n tro l menu controls access to 6 menus: Tim e S e ttin g,
La n g u a g e S e ttin g, A/V O u tp u t S e ttin g, O rg a n iz in g C h a n n e ls,
O rg a n iz in g F a vo rite s and In s ta lla tio n. Press the buttons to
,
Lo c k/U n lo c k the access. Lo c kin g means controlling the access to specific
menus with the PIN Code system. The default PIN Code is 0 0 0 0.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
I-3. LANGUAGE SETTING
There are many languages available for the menu. The default language is
English.
A. Menu Language
It is an item for changing the language of the Ma in Menu.
Select which language the menus will be shown in.
[English / French / German / Italian / Spanish / Arabic / Greek / Turkish /
Danish / Swedish / Norwegian]
B. Subtitle Language
It is an item for changing the language of the subtitle.
As long as the services support, the subtitle language is changeable by pressing
the
button on your RCU.
[English / French / German / Italian / Spanish / Arabic / Greek / Turkish /
Danish / Swedish / Norwegian]
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
C. Audio Language
It is an item for changing the language of the Audio.
The first audio language is set to English. If more than one audio language is
transmitted, you may select one language among several languages transmitted
by pressing the
button.
[English / French / German / Italian / Spanish / Arabic / Greek / Turkish /
Danish / Swedish / Norwegian]
I-4. A/V OUTPUT SETTING
The STB has many A/V Outputs. Control this menu properly according to external
components connected to the STB. Configurations concerning Audio and Video can
be made here.
A. TV Type
Enables the setting of the TV standard.
B. TV Aspect Ratio
Enables the setting of the screen format of the TV. Select 4 :3 or 1 6 :9 mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
C. Display Format
Enables the setting of the screen format of the TV. Select the Le tte r Bo x
or C e n te r e xtra c t mode of 16:9 pictures by using
,
buttons.
D. Sound Mode
Allows you to configure the sound mode. Select the S te re o, Mo n o, Le ft and
R ig h t modes by using the buttons. The Sound mode is configurable later
on by using the button on your RCU.
,
E. UHF Type
Allows you to change the UHF Type. Select the P AL G, P AL I, P AL K modes
by using the
,
buttons.
F. UHF Channel
Choose the UHF Channel by using the
is CH36.
,
buttons. The default UHF channel
I-5. OSD Transparency
Adjusts the OSD transparency level of all kinds of menus. The available levels
are ranging from 0% to 50%.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
I-6. Info Box Display Time
Adjusts the time-out of the Info Box. Sets the period of time the Info Box is
displayed on screen. The adjustable time is from 0 to 30 seconds.
I-7. Info Box Position
Adjusts the position of the Info Box. Allows you to change the position by using the
,
buttons.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
II. ORGANIZING CHANNELS
This mode can be used to rename, reorder, lock, hide and to delete TV Services.
A. Browse
Press the
button. Now, browsing through the O rg a n iz in g C h a n n e ls
is possible. Press assigned buttons on the help message.
B. Rename
Use the
,
buttons to select R e n a m e menu and press the
button
to move to the Channel List. Use the
,
buttons for selecting and renaming the
the channels. After renaming it, be sure to save it by pressing the
button.
C. Move
You can reorder and move the service to the preferred position. Mark the desired
channel to move and press
button. Use the
,
buttons to choose the
m o v e mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
D. Lock
You can restrain and lock the use of the services. From here, locking (and later
unlocking) channels in any of the lists is possible e.g. in order to prevent children
from watching it. If a locked service is selected, enter the PIN code in order to enjoy it.
E. Skip
You can ride and skip the services. In order to unlock the skip function, press the
button on the skipped channel. The skipped channels will not be visible on
channel list.
F. Delete
Press
button to delete channels. The delete function differs from the
skip function as it deletes the channel completely. Whereas, the skip function
just makes the channel invisible.
NOTE: Deleted channels are permanently deleted. The only way to reobtain
is to perform a new channel search.
G. Sort
You can sort and rearrange the sequence for the services.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
III. ORGANIZING FAVORITES
This mode is helpful in adding and deleting services to and from the favorite
group.
Under the menu O rg a n iz in g F a vo rite s, there are three different modes:
F a v Lis t,F a v C Hs and C h Lis t. On the F a v Lis t mode, four standard lists
are selected as the default menus: N e w s, S p o rts, Mo vie and Mu s ic. Up to
10 lists including these lists can be added and renamed.
When deleting a service, select a service in the F a v C Hs section and press the
assigned button on the help message.
To add services into Favorites, locate the cursor to the desired service and press
the
button.
Even in the Favorite CHs, you will see basic satellite & Channel information.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
IV. INSTALLATION
IV-1.LNB Setting
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
The Low Noise Blockdown Converter (LNB) amplifies the signal received by
the satellite dish and lowers the frequency of the signal. The signal is then fed
from the LNB at the dish via cable to the STB.
For the LNB Settings, move the cursor to INS TALLATIO N item and press
button.
Then, set the cursor to the LNB S e ttin g item and press
button.
A. Satellite Name
Press the
button to display the Satellite List box. The Satellite name list is
put in alphabetical order. Select one of the preprogrammed satellites that
correspond to the value of the antenna. In other words select one of the already
searched services at the first installation. If the desired satellite name is not in
the list, then select O th e rs .
B. LNB Frequency
Select the L.O. Frequency set to antenna. The LNB Frequency of 5150, 9750,
10600, 10750, 11475 MHz or Universal can be selected by using the or
button.
NOTE: If the Universal LNB is selected, both 9750 and 10600 MHz are
supported at the same time, and therefore the 22 KHz tone setting
is not required.
C. LNB Power
Select LNB power ‘ On’ for internal and ‘ Off ’ for external.
D. 22 KHz
If you are using a 22 KHz tone switch box, make 22 KHz tone switch enable
or disable to select LNB or antenna.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
E. 12V
Use it if the switch box is controlled by 12V DC. (Non-SCART model only)
F. DiSEqC 1.0
The STB is designed to be DiSEqC 1.0 compatible. This allows multiple antennas
to be connected to the STB at the same time. If using two or more fixed antennas
or LNBs, then it is recommended to use a DiSEqC 1.0 switch.
Select from 1 of DiS EqC to 4 of DiS EqC, Min i A, Min iB or Dis a b le
according to the option or the configuration of DiSEqC switch box or antenna.
G. Channel Search
It is used to go to c h a n n e l s e a rc h menu directly from LNB s e ttin g menu,
press
button at this item.
IV-2. Channel Search
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
A. Satellite Name
Press the
button to display the Satellite List Box. The Satellite name list
is put in alphabetical order. Select one of the preprogrammed satellites that
correspond to the value of the antenna. If the desired satellite name is not
in the list, then select O th e rs.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
B. Search Mode
There are 4 search modes, Au t o, Ma n u a l, Ad va n c e d and S MATV.The
Au to mode enables to search using the information the IRD has. On the other
hand, there will be a need to know in advance the frequencies and the symbol
rates before using the Ma n u a l mode. On the Ad va n c e d mode, enter the
Audio PID, Video PID or the PCR PID. The S MATV mode is used to special
purposes on satellite master antenna TV system.
C. Frequency
Enter the Transponder’s Frequency by using the numeric buttons on your RCU.
D. Symbol Rate
Enter the Transponder’s Symbol Rate by using the numeric buttons on your RCU.
E.Polarization
Choose the Type of polarization, either the Ho riz o n ta l or the Ve rtic a l.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
F. Network Search
This Ne two rk S e a rc h menu can be used if the S e a rc h m o d e is turned to
the Ma n u a l or Au t o mode. If the Ne two rk S e a rc h menu is turned on and
the NIT (Network Information Table) is available, the Transponder’s information
can be found.
G. PID
Press
button to enter Video/Audio/PCR PID’s.
1) Video PID
Insert the Video PID by using the numeric buttons on your RCU.
2) Audio PID
Insert the Audio PID by using the numeric buttons on your RCU
3) PCR PID
Insert the PCR PID by using the numeric buttons on your RCU.
Maximum 16 digits can be entered.
4) SAVE
To ensure the above Video/Audio/PCR PID change, press
at this item.
button
H. FTA/ Scrambled
Choose your favorable channels among F TA o n ly / C AS o n ly / F TA+C AS.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
I. Start Search...
Searches for digital channels after the configuration of the LNB is over. To
stop the searching process on the way, press either the
button or the
button. This menu will be shown as long as the STB is searching for channels. All
channels found will be listed in two columns on the screen; with TV channels in one
column and Radio channels in the other. Please note that the search procedure may
take a few minutes. When the search procedure is completed, the screen will show
how many TV and Radio channels have been found. Press
channels.
button to save the
J. LNB Setting
To go to LNB S e ttin g menu directly from C h a n n e l S e a rc h menu,press
button at this item.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
IV-3 . Motorized DiSEqC 1.2
If you have DiSEqC 1.2 motorised system, then you can use the DiSEqC 1.2 functions.
. Satellite Name
A selection of satellite names that will be used to identify a motor position.
. Frequency: Selects the frequency to catch the strong signal.
. DiSEqC Command Mode : Change the current mode between Us e r and In s ta lle r
modes.
- Us e r: This mode is used to fine-tune the position of the motor for better reception.
- In s ta lle r: This mode is used to search for the position of a satellite manually.
. Movement: In case of Us e r mode, the movement is adjustable by fine-tuning.
In case of In s ta lle r mode, the movement is adjustable by E a s t,We s t going
command.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
. Motor Control
- G o to : Moves the motor to the stored position of the selected satellite.
- S to re : Stores the current position of the motor for the selected satellite.
- R e s e t : Resets all stored position of the motor relative to the “0” position.
(In s ta lle r mode only)
- R e c a lc u la te : Recalculates the position of the Stab Rotor motor.
- Lim it E , W: Limits east and west position.
- Lim it O F F : Setting of the limitation.
- G o to R e f : Goes to reference.
. Channel Search: After saving the DiSEqC configuration at the highest signal strength,
press
button to start channel searching of the selected satellite.
IV-4. SAT/Tp Edit
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
A. Satellite Name
By pressing
button, you can see the listed satellite names .
Then,using or buttons, you will find Frequency, Symbol Rate and Polarization
information of each satellite.
B. Frequency
By pressing
button, you can see the all frequencies of transponders of a satellite,
and also you can select a frequency. Or, just pressing or buttons, you can select
and view a frequency one by one.
C. Symbol Rate
You can see the symbol rate of specified satellite on the right side of the menu.
D. Polarization
You can select the polarization from Ho riz o n ta l and Ve rtic a l modes.
E. Sat Name Edit
You can change the name of the satellite name by this menu.
Press button to display a keyboard. There are several items such as O th e r,
S a ve and S p a c e in the keyboard.
By selecting O th e r item, you can see a new alphabet character sets.
The S p a c e item a space between two characters. And the S a ve item is used to
confirm the new name of the satellite.
Notes: You can move the cursor in the satellite name row by or and column by
or
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
F. Add New TP
In case of new transponder information is added by broadcaster, you can add new
TP(transponder) information and enjoy new services.
Before adding new TP information, you should know the frequency, symbol rate and
polarization types.
After adding new information, you should confirm the new information by pressing
button at O K item.
G. Delete TP
By this menu selection, you can delete the selected TP(Transponder) information.
H. Add Satellite
Using this menu, you can add new satellite name by keyboard, then it will be
added in the Satellite Name menu.
I. Delete Satellite
By this menu selection, you can delete the selected satellite information.
J. Channel Search
It is used to go to c h a n n e l s e a rc h menu directly from S AT/Tp E d it menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
IV-5. Factory Setting
All the stored data can be reset just like it was manufactured.
IV-6.Transfer Program to Other IRD
It is used to transfer program to other IRD for upgrading the IRD.
Notes: Please proceed this menu with connecting the IRD of same model
and same specification.
IV-7.Transfer Data to Other IRD
It is used to transfer data such as satellite/TP information to other IRD for
upgrading the IRD.
Notes: Please proceed this menu with connecting the IRD of same model and
same specification.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
V. INFORAMTION
You can check the STB version and refer the calendar.
V-1. IRD STATUS
Check the IRD’s system information. It shows the IRD’s:
System ID
Loader Version
Device Version
Application Version
Last Update
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
V-2. CALENDAR
Press the or button to select the year. Press the
select the month.
or
button to
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
VI GAME
VI-1. Block
VI-2. Poker
Download from Www.Somanuals.com. All Manuals Search And Download.
MENU OPERATIONS
VI-3. Bricks Lay
VI-4. Bomb Hexa
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING (Q & A)
Problem
Possible Causes
What to do
Check that the main power
cable is plugged into the power
socket.
Nothing appears on the
Front Panel.
The main power cable
is not connected.
No sound or picture, but
the front panel shows the
time or -- : --
STB is in standby mode.
Turn the power ON.
The satellite dish is not
pointing at the satellite.
No Signal or Weak Signal.
LNB is faulty.
The UHF Key is
pushed down .
Adjust the dish.
Check the settings in one of
the channel search submenus.
Check the cable connections.
Replace the LNB.
No Picture, No Sound.
Get out of the UHF mode.
No Batteries.
The RCU is incorrectly
aimed.
Change the batteries (both).
Aim the RCU properly to
the STB.
The Remote Control Unit
(RCU) is not working.
The STB is in standby
mode.
Change the mode to the
normal mode.
You have forgotten your
secret PIN Code.
Contact your Service Provider.
Time Setting is wrong.
2 broadcasts overlap.
The Time is not set properly. Adjust the Time on the Menu.
The channels are not
configured properly on the
RF mode.
Set the channels in the RF mode
under the A/V setting of the
Menu between 21 to 69 on the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS(IRD)
STB SPECIFICATIONS
Item
Power
Specification
90 - 250VAC, 50 / 60Hz
950 - 2150 MHz
Input Frequency
DATA Service
1 RS - 232C, 115kbps
SCART (SCART model only)
CINCH A/V Out
2 SCARTS: 1 VCR, 1 TV
1Video / 2 Audio (left and right)
1Video / 2 Audio (left and right)
Convertible 13.5/18V (500mA max)
CINCH A/V In (Non-SCART model only)
LNB Power
QPSK / Multiple convolution coding
(DVB Compliant)
Modulation / FEC Type
DiSEqC Ver. 1.0 / 1.2 compatible
22 KHz
DiSEqC Bus
Tone Switching
RF Modulator (Non-SCART model only)
Specification
UHF Ch. 21-69 with PAL I/G/B
MPEG - 2/DVB Compliant SI
MP@ML in MPEG-2
4:3 or 16:9
Video Compression
Aspect Ratio
On-Screen Display
EPG
256 colors with full resolution
Supported
CHANNEL PROCESSING
Item
Specification
Input Frequency Range
950 - 2150 MHz
Number of Channels
3500 TV Channels and1500 Radio Channels
Tuning System
Tuning Step Size
Modulation
PLL Digital Synthesis Channels
125 KHz Max
QPSK (DVB Specification)
Rates: 1/2, 2/3, 3/4, 5/6, 7/8
(DVB Specification)
Inner FEC
Outer FEC
Input Symbol Rate
IF Bandwidth
Reed Solomon coding RS (204, 188, t=8)
2 to 45 Ms/s
27MHz
F Type ( IEC 169 - 24 female)
Connector Type
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS(IRD)
MPEG AUDIO
Item
Specification
Mono , Left , Right and Stereo
32, 44.1 and 48 kHz
Operation Mode
Sampling Rates
Resolution
18 bit digital to analogue Converters
VIDEO SPECIFICATIONS
Item
Specification
Specification
Meets ETR 154 amended in ALM-95-021
PAL I ,G,K
TV System
Video Decoding
Video Resolution
ISO / IEC 13818-2, MP@ML
720 pixels 576 lines 25 frames per sec.
RF MODULATOR (Non-SCART model only)
Item
Specification
Input RF bypass Supported.
IEC Coaxial female 9.5 mm.(IEC 168-2)
CCIR UHF E 22-69 adjustable
Channel 36 (or TBD)
Features
Connector
Channel Range
Pre-Set Channel
. POWER SUPPLY
Item
Input Voltage
Type
Specification
90 - 250VAC, 50 / 60Hz
SMPS
Power Consumption
Standby Power
Protection
Max.30Watt
8Watt
Separate internal fuse
Download from Www.Somanuals.com. All Manuals Search And Download.
|