TP Link Security Camera tlsc3130g User Manual

TL-SC3130G  
Wireless 2-Way Audio Surveillance Camera  
REV: 2.0.2  
1910010429  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC STATEMENT  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the interference by one or more of the following  
measures:  
¾
¾
¾
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
¾
Consult the dealer or an experienced radio/ TV technician for help.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
1) This device may not cause harmful interference.  
2) This device must accept any interference received, including interference that may cause  
undesired operation.  
Any changes or modifications not expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment.  
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized  
modifications to this equipment. Such modifications could void the user’s authority to operate the  
equipment.  
CE Mark Warning  
This is a class B product. In a domestic environment, this product may cause radio interference, in  
which case the user may be required to take adequate measures.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Package Contents  
The follow items should be found in your package:  
¾
¾
¾
¾
¾
¾
TL-SC3130G Wireless 2-Way Audio Surveillance Camera  
Power Adapter  
Mounting Bracket with three screws, a Lock Ring, a Brace and a Base Plate  
RJ45 Cable  
Quick Installation Guide  
Resource CD, including:  
z
z
z
This User Guide  
Application Guide  
Other helpful information  
Note:  
)
Make sure that the package contains the above items. If any of the listed items are damaged or  
missing, please contact your distributor.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Chapter 1 Minimum System Requirements  
We strongly recommend your computers follow our minimum requirements in order to use this  
IP-Camera normally. If your computer doesn’t meet these requirements below, it might cause  
some problems.  
Item  
Requirements  
CPU  
Pentium 4 1600MHz (or equivalent AMD)  
Graphic Card  
RAM  
64 MB RAM graphic cards(or equivalent on-board graphic cards)  
512 MB  
Windows 98, Windows ME (Please see  
Note)  
)
Operating System  
Windows2000, 2003, XP, Vista, Mac OS X Leopard  
Internet Explore 6 or above  
Web Browser  
Note:  
)
1. If you are using Windows 98 or Windows ME, please install IP Installer before using WEB UI  
to ensure the system runs normally.  
2. If you can't view the record video file, please install Xvid codec while installing Intelligent IP  
Installer. (For Windows 98, ME or 2000 server, the codec might not work properly. You’ll need  
to download Xvid codec 1.0 from the Internet.)  
3. Please always update the latest Windows component. (Net Framework, Windows Media  
Player, Enhance ActiveX Security)  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Chapter 2 Physical Overview  
2.1 Front View  
Focus Adjustment Ring: Adjust the focus ring to get a clear image.  
Network LED Indicator: It lights up when the IP Camera is well connected to the network. It  
flashes when there are data being transmitted.  
Power LED Indicator: It lights up when the IP Camera is powered on.  
Built-in Microphone: The location where the voice from your partner comes out.  
2.2 Bottom view  
Power Connector: The power connector is where you connect the power adapter.  
Reset: To successfully restore the camera to factory defaults, please keep the device powered on,  
then press and hold the Reset Button for at least 10 seconds. The CPU of the camera starts to  
work completely 1 minute after you release the Reset button.  
Audio Out (Speaker): The Audio Out (Speaker) port is where the speaker is connected.  
LAN (Network Connector): Through this port, you can connect the IP Camera to your computer  
or the other Ethernet network devices.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Chapter 3 Using IP Camera via Web Browser  
3.1 Windows Web Browser  
1. Launch your web browser, and enter the IP address (the default value is 192.168.1.10) of the  
IP camera in the Location / Address field of your browser.  
Note:  
)
video without setting page.  
2. Enter the default User name “admin” and password “admin” in the login window as shown  
below.  
Note:  
)
The default User name “admin” and Password “admin” are set at the factory for the administrator.  
You can change them in the Account Menu. (Please check “SETTING BASIC Security →  
Account”)  
3. The web-based management page will display on your screen. On the leftmost column of the  
web-based management page are Setting, Client Setting, and Image Setup. For more  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3.2 Mac Web Browser  
1. Click the Safari icon on the screen as the figure below shown, and enter the IP address (the  
default value is 192.168.1.10) of the IP camera in the Location / Address field of your browser.  
Note:  
)
video without setting page.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Enter the default User name “admin” and password “admin” in the dialog box as shown below.  
Note:  
)
The default Name “admin” and Password “admin” are set at the factory for the administrator. You  
can change them in the Account Menu. (Please check “SETTING BASIC Security →  
Account”)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. The web-based management page will be display on your screen. In the leftmost column of  
the web-based management page are Setting, Client Setting, and Image Setup. For more  
details, you can refer to Section 5.2Section 5.3 and Section 5.4.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4 Operating IP Camera via Mobile Phone  
4.1 Mobile Phone Viewing  
4.1.1  
3G Mobile Phone Streaming Viewing  
For 3G mobile phone viewing, type “rtsp://<IP>:<PORT>/video.3gp ” into your 3G Streaming  
Link. <IP> is the Public IP address of your IP camera; <PORT> is the RTSP port of your IP camera  
(Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp  
Note:  
)
You can also use RTSP clients (RealPlayer, VLC, QuickTime Player…etc.) to view RTSP  
streaming, just type in “rtsp://<IP>:<PORT>/video.3gp” as the Player URL.  
4.1.2  
2.5G Mobile Phone WAP Viewing  
For 2.5G mobile phone viewing, type “http://<IP>/mobile.wml” into your 2.5G WAP Browser. <IP>  
is the Public IP address of your IP camera.  
4.1.3  
2.5G Mobile Phone Browser Viewing  
For 2.5G mobile phone viewing, type “http://<IP>/mobile.htm” into your 2.5G Web Browser. <IP>  
is the Public IP address of your IP camera.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
4.2 Using IP Camera via iPhone  
You can use TP-LINK Web User Interface via iPhone. Please follow the setting process below.  
Then you can use TP-LINK Web UI via iPhone.  
2. Enter IP address in your web link.  
1. Select Safari function  
3. Enter name and password.  
Default values are both admin.  
Then click Log in  
4. The TP-LINK User Interface and live  
image will show up in the middle of the  
screen.  
Note:  
)
It will show continuous snapshots  
not a real time video streaming. Therefore, the  
recording feature is disabled.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Chapter 5 Configuration of Main Menu  
You would find that the illustrative web pages in this Manual are all orange. Please note that  
they're from our latest firmware, which can be downloaded from our website. Web pages in our  
previous firmware are blue.  
On the leftmost column of the web-based management page are Setting, Client Setting, Image  
Setup. For more details, you can refer to Section 5.2 SettingSection 5.3 Client Setting、  
Section 5.4 Image Setup.  
Full screen  
Snapshot  
Zoom in / Out  
Audio button  
Video Play  
On the right column of the web-based management page, you can use Live View. There are four  
different functions which are Snapshot, Zoom, Audio and Video Play. You can see more details  
as follows.  
5.1 Live View  
5.1.1 Snapshot  
You can capture a still image shot by the camera and save it in your computer.  
Symbols Meaning  
Click it, a snapshot window will appear  
Save  
to save the picture in your computer  
to return to the view page  
full Screen  
Close  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5.1.2 Zoom in / out the image via the monitor window  
z Click  
to display the digital zoom in window.  
z Pull the  
to adjust the digital zoom range, and it  
will be showed on the above window.  
z You can use the left click of your mouse to move the  
to any where on the window to view  
the desired detail more clearly.  
5.1.3 Video play buttons  
Symbols  
Meaning  
Pause the current video  
Play the video  
Stop the current video  
Record the current video  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5.1.4 Audio buttons  
Note  
Symbols  
Meaning  
)
mean the speakers of your computer are  
turned on to transmit the sounds from the  
connected IP camera(s)  
Speakers turned on  
Speakers turned off  
Microphone turned on  
mean you can broadcast to the connected  
IP camera(s) via the Ethernet using your  
microphone  
Microphone turned off  
Volume control bar  
5.2 Setting  
This function is only for the Administrator. Click this button to get into the Basic and Advance  
settings menus.  
There are four sub-menus under the BASIC menu, which includes System, Camera, Network,  
and Security. For more information, you can refer to Section 6.1Section 6.2Section 6.3 and  
Section 6.4.  
There are six sub-menus under the Advance menu, which includes FTP Client, SMTP, HTTP  
event, Schedule, Motion Detection, and System Log. Fore more information, you can refer to  
Section 7.1Section 7.2Section 7.3Section 7.4Section 7.5 and Section 7.6.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
5.3 Client Setting  
This function is only for the client.  
Click this button to configure the settings of IP Camera, which includes Mode, View Size,  
Protocol, and Video Buffer.  
5.3.1 Mode  
Click the drop-down list to choose between MPEG4 and MJPEG video compression mode.  
Note:  
)
MJPEG streaming is unavailable if RTSP mode is On (Please check SETTING BASIC →  
Camera General).  
5.3.2 View Size  
Select the desired display image resolution to 640*480 or 320*240. It is suggested that you go to  
Client Setting to select a suitable View Size before using the IP camera as shown in the figure  
below. For the PC whose resolution is less than 1280*1024, View Size of 320*240 is  
recommended.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5.3.3 Protocol  
Select the transferring protocol from TCP, UDP, HTTP and Multicast.  
Note:  
)
This item appears just after RSTP mode is enabled (selecting SETTING BASIC Camera →  
General)  
5.3.4 Video Buffer  
Turn the Video Buffer function ON / OFF. The Video Buffer function makes the streaming more  
smoothly in unsteady network environment, but might cause a little delay in live viewing.  
5.4 Image Setup  
You can use the tool bar to optimize video Brightness, Contrast, Saturation and Hue.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5.4.1 Brightness  
The higher value the brightness is, the brighter the image is.  
5.4.2 Contrast  
The contrast is a measure of a display system, defined as the ratio of white to black that the  
system is capable of producing. The higher value the contrast is, the more delicate color you can  
get.  
5.4.3 Saturation  
The saturation of a color is determined by a combination of light intensity and how much it is  
distributed across the spectrum of different wavelengths. The higher value the saturation is, the  
more colorful the image will be.  
5.4.4 Hue  
Hue is one of the three main attributes of perceived color, which is affected by different wavelength  
of color. With higher value of hue, color will be much more vivid.  
5.4.5 Default  
After the adjustment of all settings, you can still click Default to make the setting back to the  
factory default settings.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Chapter 6 Setting-Basic  
Click BASIC to display the submenus including System, Camera, Network, and Security.  
6.1 System  
Click System to display the submenus including Information, Date / Time, and Initialize.  
6.1.1 Information  
The Information page provides the basic information of the product which includes Product  
Name, Firmware Version and Web Version.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
6.1.2 Date / Time  
The Date/ Time page displays all options of time setting.  
¾
¾
¾
Current date / time: Displays the current date and time of this IP Camera.  
PC clock: Displays the date and time of the monitoring PC clock.  
Date / Time format: You can click the drop-down list to select different time display  
formats.  
¾
Adjust: You can select one of those four adjusting modes for your IP Camera.  
z Keep current setting: Select this mode to keep the current date and time of this IP  
Camera.  
z Synchronize with PC: Select this mode to keep the date and time of this IP Camera the  
same with the monitoring PC.  
z Manual setting: Select this mode to adjust manually the date and time of this IP Camera.  
z Synchronize with NTP: Specify the NTP server name and the Refresh Interval to  
synchronize the date and time of this IP Camera with those of the time server, known as  
the NTP server.  
z Time Zone: You can select the format from Greenwich Mean Time. The time displayed will  
be the same as the current date / time option.  
Note:  
)
The NTP server (Network Time Protocol) is the time server which is an Internet standard protocol  
built on the top of TCP / IP. This assures accurate synchronization to the millisecond of computer  
clock time in a network of computers.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6.1.3 Initialize  
¾
¾
Reboot: Click this button to reboot this IP Camera. A confirmation dialogue will appear and  
then click OK to process. It takes two minutes to reboot this IP Camera.  
Factory Default: Click this button to reset this IP Camera to the factory default settings. A  
confirmation dialogue will appear and then click OK to process. The network LED indicator on  
the IP Camera will start to blink. This IP Camera will reboot automatically after the restoring  
has been finished. Don't turn off this IP Camera during this process.  
¾
¾
¾
Backup Setting: You can save configuration setting data of this IP Camera into a file. Click  
Save and follow the instructions on the browser to save this setting data file to specified  
location.  
Restore Setting: Download the saved setting data of this IP Camera. Click Browse… and  
select the saved file. Click OK and this IP Camera is adjusted according to the loaded data  
and then restarted.  
Firmware Upgrade: Upgrade the device software. Click Browse… and select the file for  
upgrading. A confirmation dialogue will appear. Click OK to start. This IP Camera will reboot  
after upgrading has been finished.  
Note:  
)
Use only upgrade files that are special for this IP Camera. Otherwise problems may occur. Don't  
turn off the IP Camera power or disconnect the network until the upgrading is completed.  
¾
Upload Language Pack: Upgrade the device language pack. Click Browse… and select  
the file for upgrading. A confirmation dialogue will appear. Click OK to start upgrading. The  
upgrade is applied immediately. The default language is “English.”  
6.2 Camera  
Click Camera to display the submenus including General, MPEG4 and MJPEG.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
6.2.1 General  
¾
RTSP: Switch is On or Off  
Note:  
)
RTSP (Real Time Streaming Protocol) is a protocol used in streaming media system which allows  
clients to remotely control a streaming video server. RTSP is supports by most of the media clients  
such as Real Player, QuickTime and VLC...etc.  
¾
¾
Image Rotate: You can mirror or flip the display screen.  
Night Mode: You can choose Auto / Off. If you choose Auto option, the camera will adjust  
automatically to perform well when the environment is not bright enough.  
¾
¾
Lighting: You can choose the environment among 50 Hz, 60 Hz, and Outdoor.  
White Balance: You can choose the white balance to Auto, Florescent, Incandescent and  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Black & White.  
¾
Overlay:  
z Text Overlay: You can see some information on the display screen which includes Date /  
Time and user-defined text. Also, you can change the background color.  
z Privacy Mask: You can cover a specific area of the video image.  
6.2.2 MPEG4  
A. Computer View  
¾
¾
RTSP (if RTSP mode is On, please check “SETTING BASIC Camera General”)  
z RTSP Port: Specify the transmission port number of RTSP streaming. The default value is  
8554.  
z Viewer Authentication: If the viewer authentication is On, the users will be requested to  
type in username and password when viewing through RTSP.  
RTP (if RTSP mode is On, please check “SETTING BASICCamera General“)  
z Unicast Streaming Video / Audio Port Range: Specify the transmission port range of  
RTP streaming video. RTP will select a port randomly from this range.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
z Multicast Streaming (If it is ON)  
9 Multicast Address: Specify the multicast server address.  
9 Video / Audio Port: Specify the transmission port number of the video data, which is  
an even number from 1024 to 65534.  
9 Time- to- Live: Set the maximum TTL(Transistor-Transistor Logic) that multicast can  
pass through.  
¾
¾
¾
Image Size: Specify the image size when the network camera transmits. You can choose  
among 640 x 480, 320 x 240, and 160 x 120.  
Frame Rate: Set the frame rate of the MPEG4 image. You can choose values from 5, 10, 15,  
20, 25, and 30 fps. The unit “fps” stands for “frames per second”.  
Quality:  
z Auto: The quality and bitrate will be adjusted automatically according to the frame rate.  
z Fixed Quality: You can select the value of quality among Medium, Good, Delicate and  
Excellent.  
z Fixed Bitrate: Set the bitrate of MPEG4 image transmission for a line. You can select the  
values from 64, 128, 256, 384, 512, 768, 1024, 1280, 1536, and 2048 kbps.  
¾
MPEG4 view port (if RTSP mode is Off, please check “Setting Basic Camera →  
General”)  
z Unicast Streaming Video / Audio Port Number: Specify the transmission port number of  
the video data (the default value is 8090). You can specify an even number from 1024 to  
65534. If you change the setting of Video / Audio Port Number, the setting of Video / Audio  
Port Number (SSL) will change automatically.  
B. Mobile View  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
¾
¾
RTSP (if RTSP mode is On, please check “SETTING BASIC Camera General”)  
z RTSP Port: Specify the transmission port number of RTSP streaming. The default value is  
554.  
RTP (if RTSP mode is On, please check “SETTING BASIC Camera General”)  
z Unicast Streaming Video / Audio Port Range: Specify the transmission port range of  
RTP streaming video. RTP will select a port randomly from the range.  
z Multicast Streaming (If it is ON)  
9 Multicast Address: Specify the multicast server address.  
9 Video / Audio Port: Specify the transmission port number of the video data, which is  
an even number from 1024 to 65534. It is set to 10000 and 11000 by default.  
9 Time- to- Live: Set the maximum TTL(Transistor-Transistor Logic) that multicast can  
pass through.  
¾
¾
Image Size: The image size of Mobile View is fixed at 160 x 120.  
Frame Rate: Set the frame rate of the MPEG4 image. You can choose values from 5, 10, 15,  
20 fps. The unit “fps” stands for “frames sent per second”.  
¾
Quality:  
z Fixed Bitrate: Set the bitrate of MPEG4 image transmission for a line. You can select the  
value from 64, 32, 16 kbps.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.2.3 MJPEG  
¾
MJPEG Viewer Port ( If RTSP is off, please check “SETTING BASIC Camera →  
General”)  
z Unicast Streaming Video / Audio Port Number: Specify the transmission port number of  
the video data (the default value is 8070). You can specify an even number from 1024 to  
65534. If you change the setting of Video / Audio Port Number, the setting of Video / Audio  
Port Number (SSL) will change automatically.  
¾
¾
¾
Image Size: Specify the image size when the network camera transmits. You can choose  
among 640 x 480, 320 x 240, and 160 x 120.  
Frame Rate: Set the frame rate of the MJPEG image. You can choose values from 5, 10, 15  
fps. The unit “fps” stands for “frames per second”.  
Quality:  
z Auto: The quality will be automatically decided.  
z Fixed Quality: You can select the value of quality among Medium, Standard, Good,  
Delicate and Excellent.  
6.3 Network  
Click Network to display the submenus including Information, PPPoE, DDNS, UPnP, Bonjour,  
IP Notification.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
6.3.1 Information  
The page of Information displays the MAC address of the device.  
¾
¾
Obtain an IP address automatically (DHCP): (If a DHCP server is installed on the network)  
Select this, the IP will be assigned by the DHCP serve.  
Obtain DNS server address automatically: Select this to obtain the address of DNS server  
automatically.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
¾
Use the following IP address: Select this when the fixed IP address is set.  
z IP address: Enter the IP address of the device.  
z Subnet mask: Enter the subnet mask.  
z Default gateway: Enter the default gateway.  
Use the following DNS server address: Select this when you set the fixed IP address as the  
IP address of DNS server.  
z Primary DNS server: Enter the IP address of the primary DNS server.  
z Secondary DNS server (optional): Enter the IP address of the secondary DNS server if  
necessary.  
¾
HTTP port number: Select 80 in general situations. If you want to use a port number other  
than 80, select the text box and enter a port number between 1024 and 65535.  
z When you have set the HTTP port number to a number other than 80 on the Network  
setting page or in the Setup Program, access the device by typing the IP address of the  
device on the web browser as follows: for example, when HTTP port number is set to  
2000, you should type in http://192.168.1.100:2000/ to access the device.  
The change of settings will not take effect until the camera is rebooted. Please go to  
“SETTINGBASIC System Initialize” page and click the Reboot button as shown in  
the figure below after you make some changes.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note:  
)
If you connect the IP Camera with your computer directly, the default network domain of camera is  
192.168.1.x.  
6.3.2 PPPoE (Point-to-Point Protocol over Ethernet)  
If your ISP provides Dynamic IP with authentication by username and password, enter all PPPoE  
information in this part. When you use the PPPoE function, you need to turn on the DDNS or IP  
Notification function at the same time.  
¾
¾
IP address: The IP address obtained when the IP camera connecting with network at PPPoE.  
User ID: Enter the user ID for authentication necessary for PPPoE connections. Type it up to  
64 characters.  
¾
Password: Enter the password for authentication necessary for PPPoE connections. Type it  
up to 32 characters.  
¾
¾
Re-type password: Re-type the password to confirm.  
Obtain DNS server address automatically: Select this to obtain the address of DNS server  
automatically.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
Use the following DNS server address: Select this when you set the fixed IP address as the  
IP address of DNS server.  
z Primary DNS server: Enter the IP address of the primary DNS server.  
z Secondary DNS server: Enter the IP address of the secondary DNS server.  
Note:  
)
1)  
PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network protocol for  
encapsulating Point-to-Point Protocol frames insider Ethernet frames. PPPoE connection is  
used mainly with ADSL service where individual users connect to the ADSL transceiver  
(modem) over Ethernet work. It also widely used in XDSL (digital affiliate line such as ADSL,  
VDSL or SDSL)  
2)  
3)  
The IP Camera needs to be rebooted after it finishes changing the network completely. For  
more details, please refer to Section 6.1.3 Initialize.  
The IP Camera with Intelligent IP Installer can’t be founded after PPPoE is active, but you  
can get the IP address of the camera by IP Notification function. For more details, please  
4)  
If the IP Notification function is not configured to report the IP address of the camera, you  
can reset the camera to its factory default settings by pressing the Reset button. Then the  
camera can be found by Intelligent IP Installer.  
The change of settings will not take effect until the camera is rebooted. Please go to “System ->  
Initialize” page and click the Reboot button as show in the figure below after you make some  
changes.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.3.3 DDNS (Dynamic DNS)  
Choose menu “Dynamic DNS”, you can configure the Dynamic DNS function.  
The IP Camera offers the DDNS (Dynamic Domain Name System) feature, which allows the  
hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself)  
and a dynamic IP address, and then your friends can connect to your server by entering your  
domain name no matter what your IP address is. Before using this feature, you need to sign up for  
DDNS service providers such as www.dyndns.org, or www.no-ip.org. The Dynamic DNS client  
service provider will give you a password or key.  
¾
¾
Server name: Choose the DDNS Server from the list.  
User ID: Enter the user ID for authentication necessary for DDNS connections. Type it up to  
64 characters.  
¾
¾
Password: Enter the password for authentication necessary for DDNS connections. Type it  
up to 32 characters.  
Re-type password: Re-type the password to confirm.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
Host name: Enter the host name that is registered to the DDNS server.  
Note:  
)
How to apply DDNS username and Host name?  
You can apply DDNS username and Host name by the following steps:  
1. Log in http://www.dyndns.org, click the Create Account.  
2. Input all information and follow step by step with DynDNS.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Log in with new account and click Account My Hosts Add Host Services.  
4. Type domain in the Hostname field and select sub-domain.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. After typing in information, check your DDNS service.  
6. Type your DDNS User ID, Password and Host name in Setting Network DDNS. After  
completing setting, reboot IP Camera.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.3.4 UPnP (Universal Plug and Play)  
Choose menu “NetworkUPnP”, you can view the information about UPnP (Universal Plug and  
Play) in the screen as shown in the following figure. The UPnP feature allows the devices, such as  
Internet computers, to access the local host resources or devices as needed. UPnP devices can  
be automatically discovered by the UPnP service application on the LAN.  
¾
¾
¾
HTTP port: Enter the HTTP port number and the default HTTP port is 80.  
SSL port: Enter the SSL port number and the default SSL port is 443.  
MPEG4 viewer port: Enter the MPEG4 viewer port number and the default MPEG4 viewer  
port is 8090.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
¾
¾
¾
MPEG4 viewer port (SSL): Enter the MPEG4 SSL viewer port and the default MPEG4  
viewer port number is 8091.  
MJPEG viewer port: Enter the MJPEG viewer port number and default MJPEG viewer port is  
8070.  
MJPEG viewer port (SSL): Enter the MPEG4 SSL viewer port and default MJPEG viewer  
port number is 8071.  
MPEG4 RTSP port: Enter the MPEG4 RTSP port, default value is 8050 for computer view,  
8030 for mobile view.  
Note:  
)
UPnP (Universal Plug and Play): UPnP is a set of computer network protocol. It allows devices  
to connect seamlessly and simplify the implementation of networks at home and corporate  
environments. The device supports UPnP which is enabled by default. The device will be  
automatically detected and a new icon will be added to “My Network Place” if it also enables on  
your computer. It provides Port Forwarding for opening a port in a router or firewall in a private  
network in order to let a party from the outside world contact a inside user.  
6.3.5 Bonjour  
Bonjour, also known as zero-configuration networking, enables automatic discovery of  
computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to  
allow devices to automatically discover each other without the need to enter IP addresses or  
configure DNS servers.  
¾
Device Name: Enter Device Name to your needs.  
Note:  
)
How to use Bonjour in your Windows Browser UI? Please check the link below:  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6.3.6 IP Notification  
Once IP Notification is set to "On", the camera will automatically send an e-mail notification to  
tell users its updated network parameters if the network settings about IP addressnetwork  
connection type HTTP port or wireless connection is changed or completed. (Some settings  
will take effect after rebooting.)  
¾
Notify Type: You can select the notify type among DHCP, Static IP, and PPPoE. When the  
network settings related to the chosen notify type are changed, an e-mail notification will be  
sent to inform you of the updated network information of the camera.  
¾
¾
SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address of  
the SMTP server.  
SMTP Server Port: You can set port number from 1~65535 according to your mail server.  
The default value is 25.  
z SSL: It is Security setting. Checking SSL box if the mail server you use has security  
restriction.  
Note:  
)
If you use g-mail as your mail server, you should set 587 as your port number and check SSL box.  
¾
Authentication: Select the authentication required when you send an email.  
z Off: Select this if no authentication is necessary when an email is sent.  
z On: If authentication is necessary when an e-mail is sent, there are SMPT, POP before  
SMPT or both three options.  
z SMTP: Select this if SMTP authentication is necessary when an e-mail is sent.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
z POP before SMTP: Select this if POP before SMTP authentication is necessary when an  
e-mail is sent. If this option is selected, the IP Notification page will be different as  
following figure shown.  
z POP server name: It is necessary when the POP before SMTP is selected in  
Authentication. Type the POP (receiving mail) server name up to 64 characters, or type the  
IP address of the POP server. This setting is necessary when the SMTP server which  
sends e-mails performs authentication using the POP user account.  
z User name, Password: Type the username and password of the user who has the mail  
account. This setting is necessary when the SMTP server which sends e-mails performs  
authentication.  
¾
¾
¾
¾
Recipient e-mail address: Type the recipient e-Mail address up to 64 characters. You can  
specify up to three recipient E-mail addresses.  
Administrator e-mail address: Type the Administrator e-Mail address up to 64 characters.  
This address is used for reply mail and sending system messages from the SMTP server.  
Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is  
sent according to the IP notification.  
Message: Type the text of the E-mail up to 384 characters. Default value provides network  
information including IP, Port, MAC, Model, Firmware Version and Web Version.  
6.3.7 Wireless  
Choose Network Wireless, you can configure the wireless function for the camera in the figure  
below.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
The wireless network has to be set up by using cable network connection. After setting the camera  
correctly, the wireless function can work without cable network connection. Please follow the  
setting process below step by step:  
1. Connect IP Camera with Ethernet connection.  
2. Go to SETTING BASIC Network Wireless, and choose option “On”. You will see the  
wireless setting page.  
3. Then click Refresh. All access points (AP) around you will show up.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Select the AP you wish to connect.  
5. Enter password in Passphrase field if you need. If you don't know the setting of the wireless  
AP, please ask your network administrator.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Choose the option of Obtain an IP address automatically (DHCP) or Use the following IP  
address:  
¾
Use the following IP address: Select this when the fixed IP address is set.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IP address: Enter the IP address of the device.  
Subnet mask: Enter the subnet mask.  
Default gateway: Enter the default gateway.  
Use the following DNS server address: Select this when you set the fixed address  
as the IP address of DNS server.  
Primary DNS server: Enter the IP address of the primary DNS server.  
Secondary DNS server: Enter the IP address of the secondary DNS server, if  
necessary.  
7. Please click OK button to finish the wireless setting. Now please have a short rest or work on  
other business, for the wireless setting will take effect 1 minute after you click OK.  
8. Please unplug the Ethernet cable connecting the TL-SC3130G and the Router (or the PC),  
and log into the IP camera with its wireless address.  
6.3.8 Messenger  
(Supports up to Windows Live Messenger version 8089)  
If the firmware of your IP Camera has been updated to LM.1.6.16.03P5, then the Messenger  
submenu will be displayed under the Network menu. Click the Messenger submenu, the  
Messenger configuration page will be displayed similar to the figure shows below. This function  
allows you to use the desired computer with MSN installed to view the video captured by the IP  
camera.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
Messenger: Check the radio button before On, so you can use your IP Camera via this  
function.  
¾
¾
¾
¾
¾
Protocol: Displays the protocol used.  
Login Account: Enter the MSN account registered for you IP Camera.  
Password: Enter the password of the MSN account.  
Re-type password: Type the password again.  
Alias: Give an alias for the account of your IP Camera. The figure above takes  
“TL-SC3130G” for example.  
¾
¾
Port range: Enter the port range used.  
IP Notification: When this feature is enabled, the IP camera would notify "friends" on MSN  
about its IP address when it logs into the MSN account or when its IP address is changed.  
¾
¾
Privacy: When this feature is enabled, the MSN stream will be secured, then only users  
whose MSN ids are in the Allow List can add the camera's MSN account and view the camera  
video. When it's disabled, any user can add the camera's MSN id and see it.  
Allow list: Enter the account of the MSN user you want communicate with in “User” field.  
Click Add button and then the account will be added to the “Allow list”. Choose an account in  
the “Allow list” and click Remove button to delete it.  
To use MSN to view the video captured by the IP camera, please follow the steps below.  
A. Configuring your IP camera  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note:  
)
If you use a Modem Router to access the Internet, you should set your IP Camera as the virtual  
server with port range 20000-21000 on the Modem Router’s web-based management page.  
1. Click BASIC->Network->Messenger” to enter the “Messenger” page. Enable Messenger  
and then set the Login Account, Password, Alias, Port range, IP Notification, Privacy and  
Allow list parameters as the above figure shows. Click OK to save your settings.  
2. Click BASIC->Network->Information” to enter the “Information” page. Add 192.168.1.1 as  
the Primary DNS server.  
3. Click Advanced->System Log->Setting” to see if there is “Messenger is Ready” information  
as the figure below shows. If there is, go on with the following steps.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. Add the camera’s msn account  
1. Make sure the desired computer with MSN installed. Log into the MSN.  
2. Make sure the MSN view plugin is installed.  
This plugin is embedded in IntelligentIPInstallerSetup(TPLink)-1.1.16.09.exe and will be  
installed automatically when you install IntelligentIPInstallerSetup(TPLink)-1.1.16.09.exe.  
You can download the IntelligentIPInstallerSetup(TPLink)-1.1.16.09.exe here:  
3. Log into your MSN account.  
4. Add the camera’s MSN account as a contact.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Check its status. Normally it should be online.  
6. Click the camera icon  
and select View a contact’s webcam to view the video.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Wait for a moment, and you will see the video captured by your IP Camera.  
6.4 Security  
Click Security to display the submenus including Account and HTTPS.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6.4.1 Account  
The device default account and password setting is “admin / admin”. That means everyone who  
knows IP address can access the device including all configuration. Therefore, it is necessary to  
assign a password if the device is intended to be accessed by others.  
¾
¾
¾
¾
User name: Set a user name between 4-16 characters.  
Password: Set a password between 4-16 characters.  
Re-type Password: Re-type the password to confirm.  
Viewer Mode: Set the user mode among Admin, Operator, and Viewer. Different viewer mode  
has different limits of authority.  
z The Admin mode has all authority of configuration.  
z The Operator mode can not only view the Live View but also control the PTZ (apply in  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
speed dome).  
z The Viewer mode only can view the Live View.  
¾
Viewer Authentication: Select whether the authentication is needed when users access  
to live view.  
z
On: Authentication is required to let different users have different levels of permission  
to access the camera view.  
z
Off: Authentication is not required to access the camera. Click Off and select one  
(among Admin, Operator and Viewer) from the pull-down list as default, then all  
users can view directly the video with the default permission without entering  
username and password.  
* If you want to have a higher authority than the default, you can key in appropriate username  
and password in the dialog box that pops up when performing advanced operations that are  
only allowed by the higher authority.  
6.4.2 HTTPS  
HTTPS is a URL scheme used to indicate a secure HTTP connection. It is syntactically identical to  
different default TCP port (443) and an additional encryption / authentication layer between the  
“http://”.  
¾
¾
¾
Create & Install: Create a self-signed certificate for HTTPS to recognize.  
Installed Certificate: Display or remove the properties of the installed certificate.  
HTTPS Connection Policy: Set HTTPS connection policy for different level of users.  
To use the HTTPS encryption, please set up “Create self-signed certificate” for the first time you  
use the HTTPS function, and then set up the connection policy for different users.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Note:  
)
When enable HTTPS with RTSP on mode, the IP Camera only protect the setting such as  
username and password and do not protect video and audio.  
When enable HTTPS with RTSP off mode, the IP Camera will protect all setting including video  
and audio.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7 Setting-Advance  
Click Advance to display the submenus including FTP client, SMTP, HTTP event, Schedule,  
Motion detection and System Log.  
7.1 FTP Client  
Use this menu to set up for capturing and sending images to an FTP server. By using FTP client  
function, you can send the image and video file which has been shot and recorded linked with the  
built-in motion detection function to FTP server. FTP client setting menu is composed of three  
items, General, Alarm sending and Periodical sending.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
7.1.1 General  
Select On when you use FTP function. The FTP client setting page will appear.  
Select Off when you do not wish to use the FTP client function.  
Note:  
)
The frame rate and operability on the main viewer may decrease while a file is being transmitted  
by the FTP client function.  
¾
FTP server name: Type the FTP server name to upload still images up to 64 characters, or  
the IP address of the FTP server.  
¾
¾
¾
User name: Type the user name for the FTP server.  
Password: Type the password for the FTP server.  
Retype password: To confirm the password, type the same characters as you have typed in  
the Password box.  
¾
Passive mode: Set whether you use the passive mode of FTP server or not when connecting  
to FTP server. Select On to connect to FTP server using the passive mode.  
7.1.2 Alarm sending  
Set to forward the image and video file to the specified FTP server linked with the alarm detection  
by the built-in motion detection function. Select On to send the image file to FTP server linked with  
the alarm detection.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
¾
¾
Remote Path: Type the path to the destination in FTP server up to 64 characters.  
Image File Name: Type the file name you want to assign to the images when sending to the  
FTP server. You can use up to 10 alphanumeric characters, - (hyphen) and _ (underscore) for  
naming.  
¾
Suffix: Select a suffix to add to the file name  
z Date & time: The date & time suffix is added to the Image file name. The date/time suffix  
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2  
digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus 14-digit  
number is added to the file name.  
z Sequence number: A consecutive number of 10 digits between 0000000001 and  
4294967295 and two fixed digits 00 is added to the Image file name.  
z Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.  
¾
Alarm  
z Motion Detection: Click it for using Motion Detection function as a sensor. You can set  
motion detection function on the motion detection page.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note:  
)
You can set motion detection on motion detection page. (Please go to “Setting Advance  
Motion detection Setting”) For more details, you can check Section 6.5.  
¾
Effective period: Set the period when the periodical sending is effective.  
z Always: The periodical sending is always effective.  
z Schedule: You can specify the period when the periodical sending is effective in the  
Schedule setting in the other section.  
Note:  
)
You can set schedule function on Schedule page. (Please go to “Setting Advance →  
Schedule Setting”) For more details, you can check Section 7.4.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.1.3 Periodical sending  
You can set to send an image file to FTP server periodically by selecting On to send the image file  
to FTP server linked with setting period.  
¾
Remote Path: Type the path to storage location of FTP server which you have authorized.  
¾
Image file name: Type the file name of the image sent by SMTP up to 10 alphanumeric  
characters, - (hyphen) and _ (under score).  
¾
Suffix: Select a suffix to be added to the file name sent by SMTP.  
z None: The name of the sent file will be the Image file name.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
z Date & time: The date & time suffix is added to the Image file name. The date & time suffix  
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2  
digits), minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus  
14-digit number is added to the file name.  
z Sequence number: A consecutive number is added to the Image file name.  
z Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.  
¾
¾
Interval: Set the time interval of the period sending. Min value is 1 min and Max value is 24  
hour.  
Effective period: Set the period when the periodical sending is effective.  
z Always: The periodical sending is always effective.  
z Schedule: You can specify the period when the periodical sending is effective in the  
schedule setting in the other section.  
Note:  
)
You can set schedule function on schedule page. (Please go to “Setting Advance →  
Schedule Setting”) For more details, you can check Section 7.4.  
7.2 SMTP  
Set the SMTP menu when you want to send an image via e-mail. By using Mail (SMTP) function,  
you can send a mail with attached image and video which has been shot linked with the built-in  
motion detection function. The image file can also be sent periodically. E-Mail (SMTP) setting  
menu is composed of three items, General, Alarm sending and Periodical sending.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7.2.1 General  
Select On when you use the SMTP function. The common setting options are displayed below.  
Select Off if you do not wish to use the e-Mail (SMTP) function.  
Note:  
)
The Setting of General will be the same as the setting of IP Notification (Please check “SETTING  
BASIC Network IP Notification”)  
¾
¾
SMTP server name: Type the SMTP server name up to 64 characters, or the IP address of  
the SMTP server.  
SMTP Server Port: You can set port number from 1~65535 according to your mail server.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
The default value is 25.  
¾
Security setting: Check SSL box if the mail server you use has security restriction.  
Note:  
)
If you use g-mail as your mail server, you should set 587 as your port number and check SSL box.  
¾
Authentication: Select the authentication required when you send an email.  
z Off: Select it if no authentication is necessary when an email is sent.  
z On: When authentication is necessary an e-mail is sent, select one of the authentication  
methods from the followings.  
¾
¾
SMTP: Select it if SMTP authentication is necessary when an e-mail is sent.  
POP before SMTP: Select if POP before SMTP authentication is necessary when an e-mail  
is sent.  
Note:  
)
When you set to On, be sure to select either or both SMTP or / and POP before SMTP.  
z POP server name: When the POP before SMTP is selected in Authentication, type the  
POP (receiving mail) server name up to 64 characters, or type the IP address of the POP  
server. This setting is necessary when the SMTP server which sends e-mails performs  
authentication using the POP user account.  
z User name, Password: Type the user name and Password of the user who has the mail  
account. This setting is necessary when the SMTP server which sends e-mails performs  
authentication.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
¾
¾
¾
Recipient e-mail address: Type the recipient e-Mail address up to 64 characters. You can  
specify up to three recipient E-mail addresses.  
Administrator e-mail address: Type the Administrator e-Mail address up to 64 characters.  
This address is used for reply mail and sending system messages from the SMTP server.  
Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is  
sent according to the alarm detection when Alarm sending of the alarm tab is set to On, the  
characters standing for the sensor type added to the subject.  
¾
Message: Type the text of the E-mail up to 384 characters. (A line break is equivalent to 2  
characters.)  
7.2.2 Alarm sending  
Set to send the mail with connection to the alarm detection by the built-in motion detection  
function. Select On to send the image and file to SMTP server linked with the alarm detection.  
¾
¾
Alarm sending: Select On to set to send mail with connection to the alarm detection.  
File attachment: Set whether an image file is attached to the mail sent or not. When On is  
selected, the image file made by the settings below is attached. When Off is selected, only  
the message is sent.  
¾
¾
Image file name: Type the file name you want to assign to the image to attach a mail. You  
can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming.  
Suffix: Select a suffix to add to the file name  
z Date & time: The date & time suffix is added to the Image file name. The date/time suffix  
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2  
digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus 14-digit  
number is added to the file name.  
z Sequence number: A consecutive number of 10 digits between 0000000001 and  
4294967295 and two fixed digits 00 is added to the Image file name.  
z Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
Alarm  
z Motion Detection: Click it for using Motion Detection function as a sensor. You can set  
motion detection function on the motion detection page.  
Note:  
)
You can set motion detection on motion detection page. (Please go to “Setting Advance →  
Motion detection Setting”). For more details, you can check Section 7.5.  
¾
Effective period: Set the period when the periodical sending is effective.  
z Always: The periodical sending is always effective.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
z Schedule: You can specify the period when the periodical sending is effective in the  
Schedule setting in the other section.  
Note:  
)
You can set schedule function on Schedule page. (Please go to “Setting Advance →  
Schedule Setting”) For more details, you can check Section 7.4.  
7.2.3 Periodical sending  
You can set to send an image file by SMTP server periodically by selecting On to send the image  
file by SMTP server linked with setting period.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
¾
¾
Image file name: Type the file name of the image sent by SMTP up to 10 alphanumeric  
characters, - (hyphen) and _ (under score).  
Suffix: Select a suffix to be added to the file name sent by SMTP.  
z None: The name of the sent file will be the Image file name.  
z Date & time: The date & time suffix is added to the Image file name. The date & time suffix  
consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2  
digits), minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus  
14-digit number is added to the file name.  
z Sequence number: A consecutive number is added to the Image file name.  
z Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.  
¾
¾
Interval: Set the time interval of the period sending. Minimum value is 30 min and Maximal  
value is 24 hour.  
Effective period: Set the period when the periodical sending is effective.  
z Always: The periodical sending is always effective.  
z Schedule: You can specify the period when the periodical sending is effective in the  
schedule setting in the other section. Please check “SETTING BASIC Advance →  
Schedule Setting.”  
Note:  
)
You can set schedule function on Schedule page. (Please go to “Setting Advance →  
Schedule Setting”) For more details, you can check Section 7.4.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.3 HTTP event  
Use this menu to set up for capturing and sending images to an HTTP server. By using HTTP  
client function, you can send the image file and audio file which has been shot and recorded linked  
with the built-in motion detection function to HTTP server. HTTP client setting menu is composed  
of two items, General and Alarm sending.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7.3.1 General  
¾
HTTP event: Set up the HTTP server URL, port, User ID, Password, and Proxy Server  
settings.  
For example: URL: 192.168.1.7/cgi-bin/operator/ptzset  
Note:  
)
1. The setting of URL should be the same as CGI.  
2. The example above is for reference only. For more details, please refer to SDK in the  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7.3.2 Alarm sending  
Set to send the mail with connection to the alarm detection by the built-in motion detection  
function. Select On to send the image and audio file to HTTP server linked with the alarm  
detection.  
Alarm sending: Select On to set to send mail with connection to the alarm detection.  
¾
Alarm  
z Motion detection  
¾
Effective period: Set the period when the periodical sending is effective.  
z Always: The periodical sending is always effective.  
z Schedule: You can specify the period when the periodical sending is effective in the  
schedule setting in the other section.  
Note:  
)
You can set schedule function on schedule page. (Please go to “Setting Advance →  
Schedule Setting”) For more details, you can check Section 7.4.  
¾
Alarm  
z Motion Detection: Click it for using Motion Detection function as a sensor. You can set  
motion detection function on the motion detection function page.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Note:  
)
You can set motion detection on motion detection page. (Please go to “Setting Advance →  
Motion detection Setting”) For more details, you can check Section 7.5. Motion Detection  
works only when the MPEG4 function is On.  
z Parameter: the parameter of CGI (defined in Setting Advance HTTP event →  
General URL) is from your target device. For example, move=down.  
z Message: message will show up in the form of Message = PTZ down. If your target device  
didn’t support the parameter of message, you can’t see the message. So you can just take  
the message as a note. For example: PTZ down.  
¾
Effective period: Set the period when the periodical sending is effective.  
z Always: The periodical sending is always effective.  
z Schedule: You can specify the period when the periodical sending is effective in the  
Schedule setting in the other section.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note:  
)
You can set schedule function on Schedule page. (Please go to “Setting Advance →  
Schedule Setting”) For more details, you can check Section 7.4.  
7.4 Schedule  
When you click Schedule on the Advance mode menu, the Schedule setting menu appears.  
This is the same menu as the setting menu which is displayed when you click Schedule to set  
Effective period and Schedule in FTP client setting menu, e-Mail (SMTP) setting menu, HTTP  
Event setting menu and so on.  
Example: When setting e-Mail (SMTP) (the alarm sending) in the Schedule setting menu.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
7.4.1 Setting  
¾
¾
Schedule Selection: Select the list box to specify the schedule you want to set.  
z FTP -Alarm  
z FTP - Periodical  
z e-Mail (SMTP) -Alarm  
z e-Mail (SMTP) -Periodical  
z HTTP event -Alarm  
Mon (Monday) to Sun (Sunday): The time period on the right of the checked day is the  
effective period of the schedule.  
¾
¾
Start time, End time: Specify the Start time and the End time.  
Use the same time schedule every day: When this is checked, the Start time and End time  
set to Mon (Monday) are applied to all days. In this case, the Start time and End time of the  
other days than Mon (Monday) cannot be input.  
7.5 Motion Detection  
There are three Motion Detection functions as sensors to set for different detecting zones. Each  
one has Threshold and Sensitivity inputs which you can adjust to specific zone sequentially.  
Motion Detection function can support FTP, SMTP and HTTP event for capturing and sending  
images.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
7.5.1 Setting  
¾
¾
Threshold: It means the extent which the alarm will be triggered. The default value is 50  
and the value range is 0~100. The larger the value, the higher the threshold.  
Sensitivity: It means that how often the sensor will scan the image different. The higher  
sensitivity it is and the more frequently it scans. The default value is 50 and the value  
range is 0~100. The larger the value, the higher the sensitivity.  
z
z
z
Motion Detection 1: Click it on for using Motion Detection 1 function as a sensor.  
You can adjust and move the detecting zone by using mouse.  
Motion Detection 2: Click it on for using Motion Detection 2 function as a sensor.  
You can adjust and move the detecting zone by using mouse.  
Motion Detection 3: Click it on for using Motion Detection 3 function as a sensor.  
You can adjust and move the detecting zone by using mouse.  
7.6 System Log  
The System Log function allows users to review any changes and events happened. The  
system begins logging automatically after started.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
7.6.1 Setting  
¾
Enable remote log: Enables user to send the log data to a specified log server.  
Note:  
)
There is a function called Watchdog which can automatically detect errors and restart the IP  
camera while mpeg, mjepg , 3gpp , or web cannot work. It will take about 5 minutes from detection  
to reboot, and it will show up with “connecting” on mainpage during this 5 minutes. If the Watchdog  
function detects errors ,”*** ffmpeg”, ”*** mjpeg”, ”*** gsm” or “*** boa”will be shown in system log.  
In this case, please send the file ”backup” to TP-LINK ( you can save it from Setting > Basic >  
System > Initialize > Backup setting data) , and also provide the router spec you’re using, we will  
analyze and solve the problem as soon as possible.  
E-mail : [email protected]  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Chapter 8 Appendix  
APPENDIX a – FRAME RATE & BIT RATE TABLE  
This chapter provides tables that help you to optimize your IP camera with your network environment.  
Base on your network upload environment to choose the best Image-Quality setting.  
For example, if the network environment is ADSL 256Kb(upload) / 2Mb(download), the most fluent  
Image-Quality needs to set up under 256 Kb situation.  
A.1 MPEG4 @ 30fps / kbps  
Quality  
Excellent  
Detailed  
Good  
640*480  
1000  
400  
320*240  
300  
150  
100  
70  
160*120  
90  
50  
300  
30  
Standard  
Medium  
250  
25  
250  
55  
20  
A.2 MPEG4 / kbps, fps  
Frame-Rate  
Setting  
Current  
Frame-Rate  
Image-Size  
Bitrate Setting  
Current Bitrate  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
320*240  
320*240  
320*240  
320*240  
320*240  
2048  
2048  
1536  
1536  
1024  
1024  
512  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
1800  
2200  
1500  
1700  
1000  
1000  
500  
26  
16  
30  
16  
30  
16  
30  
16  
30  
16  
30  
16  
30  
512  
600  
1536  
1536  
1024  
1024  
512  
1500  
1600  
1000  
1000  
550  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
320*240  
160*120  
160*120  
160*120  
160*120  
160*120  
160*120  
512  
1024  
1024  
512  
15  
30  
15  
30  
15  
30  
15  
600  
950  
750  
500  
50  
16  
30  
16  
30  
16  
30  
16  
512  
128  
130  
140  
128  
A.3 MJPEG @ 15fps / kbps  
Quality  
Excellent  
Detailed  
Good  
640*480  
4000  
2400  
1600  
1300  
900  
320*240  
1500  
900  
160*120  
600  
400  
650  
300  
Standard  
Medium  
500  
240  
350  
170  
A.4 MJPEG / kbps, fps  
Frame-Rate  
Setting  
Current  
Frame-Rate  
Image-Size  
Quality Setting  
Current Bitrate  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
320*240  
320*240  
320*240  
320*240  
Excellent  
Excellent  
Good  
15  
5
4000  
1600  
1600  
650  
13  
5
15  
5
13  
5
Good  
Medium  
Medium  
Excellent  
Excellent  
Good  
15  
5
900  
14  
5
360  
15  
5
1500  
550  
13  
5
15  
5
650  
13  
5
Good  
260  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
320*240  
160*120  
160*120  
160*120  
160*120  
160*120  
160*120  
160*120  
Medium  
Medium  
Excellent  
Excellent  
Good  
15  
5
350  
130  
600  
230  
300  
115  
170  
65  
13  
5
15  
5
13  
5
15  
5
13  
5
Good  
Medium  
Medium  
15  
5
13  
5
APPENDIX b – STORAGE REQUIREMENT TABLE  
This chapter provides tables that help you set your recording storage system.  
Please refer to the following table to find out the capability for recording into your hard disk.  
B.1 MPEG4 Storage Requirement GB / channel / day @ 30fps  
Quality  
Excellent  
Detailed  
Good  
640*480  
10.5  
4.2  
320*240  
3.2  
160*120  
0.9  
1.6  
0.5  
3.2  
1.1  
0.3  
Standard  
Medium  
2.6  
0.7  
0.3  
2.6  
0.6  
0.2  
B.2 MPEG4 Storage Requirement GB / channel / day @ 15fps  
Quality  
Excellent  
Detailed  
Good  
640*480  
5.3  
320*240  
1.6  
160*120  
0.4  
2.1  
0.8  
0.3  
1.6  
0.6  
0.2  
Standard  
Medium  
1.3  
0.4  
0.1  
1.3  
0.3  
0.1  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B.3 MPEG4 Storage Requirement GB / channel / day  
Image-Size  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
640*480  
320*240  
320*240  
320*240  
320*240  
320*240  
320*240  
160*120  
160*120  
160*120  
160*120  
160*120  
160*120  
Bitrate Setting  
2048  
2048  
1536  
1536  
1024  
1024  
512  
Frame-Rate Setting  
Current Bitrate  
23.0  
22.2  
18.5  
17.9  
10.5  
10.5  
5.3  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
30  
15  
512  
6.3  
1536  
1536  
1024  
1024  
512  
15.8  
16.9  
10.5  
10.5  
5.8  
512  
6.3  
1024  
1024  
512  
10.0  
7.9  
5.3  
512  
0.5  
128  
1.4  
128  
1.5  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9 FAQ  
Q1. What can I do if I forgot the login name and password?  
Press and hold the Reset button on the bottom panel with a pin or paperclip. Please continue holding  
down the Reset button for approximately 15 seconds. And then IP Camera will reboot. It will require 45  
seconds. Both the default username and password are admin.  
Q2. Why can’t I view the image from the web browser?  
First, please make sure that you are using the web browser that supports ActiveX (Internet Explorer) or  
Java script (Firefox or Safari). If it is, please install the ActiveX and Java script.  
As to the ActiveX installation, please check your internet option settings to confirm whether you’re  
allowed to install the ActiveX plug-in, which is embedded in the IP camera.  
Please click "prompt" in "Download signed ActiveX controls" in the Internet Option Security  
Settings.  
If you check that box, the ActiveX plug-in program would prompt automatically when you log in the  
camera's web page, and then please choose to install it.  
As to the Java script installation, please visit the official website here:  
Q3.If the image is blurry, what can I do?  
Please adjust the IP Camera’s focus by rotating the Lens.  
Q4. If I forgot the IP address and port of my IP Camera. What should I do?  
Please download the Intelligent IP Installer Setup from our web site, or run the CD firstly. This software  
will search the IP Camera automatically. Double click your IP Camera in this software, you will view the  
IP address and port of your IP Camera.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Technics Stereo System HQT4538 P User Manual
Thermo Products Stud Sensor USDT 2004B User Manual
The Singing Machine Karaoke Machine Compact Disc Graphics with Built In TV Karaoke Center User Manual
Toshiba Projection Television P600DL User Manual
TRENDnet Network Router TEW 310APBX User Manual
Tyco Electronics Car Video System 1928L User Manual
Tyco Smoke Alarm MX4428 User Manual
Uniden Baby Monitor UBR243 User Manual
Vermont Casting Electric Heater 1695CE User Manual
Victor Tent PL3000 User Manual