TEW-310APB
TEW-310APBX
2.4 GHz Wireless Access Point + Bridge
User's Guide
Rev. 11222002
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
Note: TEW-310APBX functions just like TEW-310APB and the configuration
procedures are the same as the TEW-310APB. The only difference between the two
models is the TEW-310APBX comes with 2 detachable antennas. Below is the
antenna installation instruction.
1
2
Locate the two antennas
inside the box.
Locate antenna connectors
on the unit.
Connectors
3
4
Screw in antenna by turning
the knob clockwise.
The antenna should fit
securely in place.
Knob
Replacing the antenna with high gain antenna
You can also replace one of the antennas with a higher gain TRENDnet antenna
(4dBi Indoor Omni Directional, 6dBi Indoor Patch Directional, or 14dBi Outdoor
Directional). At default, both antennas are transmitting/receiving data. When
installing the high gain antenna, you can choose to install it on either the left or right
antenna position. After that, go to the Access Point's configuration page, select
"Advanced Settings", and at the bottom of the page, select the desired antenna
position.
Download from Www.Somanuals.co3m. All Manuals Search And Download.
1. Package Contents
Fig. 1.1
TEW-310APB
Fig. 1.2
TEW-310APBX
Contents
TEW-310APB/TEW-310APBX Enhanced 2.4GHz Wireless Access Point
2 Detachable Antennas (TEW-310APBX only)
Power Supply 5V DC, 2.0A
Manual on CD
Quick Installation Guide
Ethernet Cable
Note: Using a power supply with a different voltage rating than the one
included with the TEW-310APB will cause damage and void the warranty for
If any of the above items are missing, please contact your reseller.
System Requirements
Computer with Windows, Macintosh, or Linux-based operating system
with an installed Ethernet adapter
Internet Explorer or Netscape Navigator version 4.0 or above, with
JavaScript enabled
Download from Www.Somanuals.co3m. All Manuals Search And Download.
2. Introduction
TEW-310APB Wireless Access Point is an enhanced 802.11b high-
performance, wireless access point. It is an ideal way to extend the reach and
number of computers connected to your wireless network.
Unlike most 802.11b access points, the TEW-310APB is capable of data
transfer speeds up to 22 Mbps (compared to the standard 11 Mbps) when used
with other TRENDnet products such as the TEW-301PC PCMCIA CardBus
AdapterandTEW-303PIWirelessPCIAdapter.
After completing the steps outlined in the Quick Installation Guide
(included in your package) you will have the ability to share information and
resources, such as files and printers, and enjoy the freedom that wireless
networkingdelivers.
The TEW-310APB is compatible with most popular operating systems,
including Macintosh, Linux and Windows, and can be integrated into a large
network. This Manual is designed to help you connect the Access Point and the
TRENDnet 2.4GHz Wireless Adapters into a network in Infrastructure mode.
Please take a look at the Getting Started section in this manual to see an
exampleofanInfrastructurenetworkusingtheTEW-310APB.
This manual provides a quick introduction to wireless technology and its
application as it relates to networking. Please take a moment to read through
this manual and get acquainted with wireless technology.
Connections
Diversity Antenna
Power Adapter Receptor
Ethernet Port (RJ-45):
Supports 10/100Mbps. Use
Ethernet cable to connect
this port to another ethernet.
Reset Button: Press
this button to reset all
configurations back to
factory result settings.
Fig. 2.1
Download from Www.Somanuals.co4m. All Manuals Search And Download.
Features and Benefits
Up to 2X Faster than regular 802.11b Products - high-speed wireless
data transfer rates up to 22Mbps. With twice the data rate and capacity,
the TEW-310APB delivers media rich content such as digital images,
videos, and MP3 files much faster than standard 802.11b networks
Fully 802.11b Compatible Fully compatible with the IEEE 802.11b
standard and interoperable with all existing 802.11b compliant devices
Improved Performance Up to 20% faster data transfer rates on standard
802.11b networks
Stronger Network Security with 256-bit WEP Encryption Supports
64/128/256-bit WEP encryption for higher level of security for your data
and wireless communication than encryption found in existing 802.11b
products
Built-in DHCP Server If enabled, it will automatically assign IP addresses
to wireless clients in a temporary network.
Web-based interface for Managing and Configuring Easy-to-use
interface independent of the operating system
4 Different Operation Modes Capable of operating in one of four different
operation modes to meet your wireless networking requirements: Access
Point, AP-to-AP Bridging,AP-to-Multipoint Bridging, and Wireless Client.
Download from Www.Somanuals.co5m. All Manuals Search And Download.
LED Indicators
LED stands for Light-Emitting-Diode. The TEW-310APB has three LEDs:
Power
Link
TX/RX
Fig. 2.2
Power - Solid red light indicates receiving power
TX/RX (Wireless Network) - Solid green light indicates
wireless connection enabled, blinking green indicates
wireless network activity
Link (Ethernet Port) - Solid green light indicates good
Ethernet connection on the RJ-45 port, blinking green
indicates Ethernet port activity
Download from Www.Somanuals.co6m. All Manuals Search And Download.
3. Wireless Basics
TRENDware wireless products are based on industry standards to provide
easy-to-use and compatible high-speed wireless connectivity within your home,
business or wherever a wireless network is available. Strictly adhering to the IEEE
standard, the TRENDware wireless family of products will allow you to access the
data you want, when and where you want it. No longer will you be limited to one
location or forced to run new wiring through your home or office. You will be able to
enjoythefreedomthatwirelessnetworkingdelivers.
A wireless local area network (WLAN) is a cellular computer network that
transmits and receives data with radio signals instead of wires. Wireless LANs are
used increasingly in both home and office environments, and public areas such as
airports, coffee shops and universities. Innovative ways to utilize WLAN technology
are helping people to work and communicate more efficiently. Increased mobility
with the absence of cabling and other fixed infrastructure have proven to be
beneficialformanyusers.
Wireless users can use the same applications they use on a wired network.
Wireless adapter cards used on laptop and desktop systems, support the same
protocols as Ethernet adapter cards. For most users, there is no noticeable
functional difference between a wired Ethernet desktop computer and a wireless
computer equipped with a wireless adapter other than the added benefit of the ability
to roam within a wireless-cell. Under many circumstances, it may be desirable for
mobile network devices to link to a conventional Ethernet LAN in order to use
servers, printers or an Internet connection supplied through the wired LAN. A
WirelessAccessPoint(AP)isadeviceusedtoprovidethislink.
PeopleusewirelessLANtechnologyformanydifferentpurposes.
Mobility - Productivity increases when people have access to data in any
location within the operating range of the WLAN. Management decisions based
onreal-timeinformationcansignificantlyimproveworkerefficiency.
Low Implementation Costs WLANs (Wireless Local Area Networks) are easy
to set up, manage, change and relocate. Networks that frequently change, both
physically and logically, can benefit from WLANs ease of implementation.
WLANs can operate in locations where installation of wiring may be impractical.
Installation Speed and Simplicity - Installing a wireless LAN system can be
fast and easy and can eliminate the need to install cable through walls and
ceilings.
Download from Www.Somanuals.co7m. All Manuals Search And Download.
Network Expansion - Wireless technology allows the network to go where
wirescannotgo.
Reduced Cost-of-Ownership - While the initial investment required for
Wireless LAN hardware might be higher than the cost of wired LAN
hardware, overall installation expenses and life-cycle costs will be
significantly lower. Long-term cost benefits are greatest in dynamic
environments requiring frequent moves, adds, and changes.
Scalability - Wireless Local Area Networks (WLANs) can be configured in a
variety of topologies to meet the needs of specific applications and
installations. Configurations are easily changed and range from peer-to-peer
networks suitable for a small number of users to full infrastructure networks
ofthousandsofusersthatallowroamingoverabroadarea.
TRENDware Wireless Family of LAN products include:
2.4GHz Wireless LAN PCI Network Adapter (TEW-301PC)
2.4GHz Witrless LAN CompactFlash Network Adapter (TEW-302CF)
2.4GHz Wireless LAN PCI Adapter (TEW-303PI)
2.4GHz Wireless LAN USB Network Adapter (TEW-304UB)
Wireless Access Point + Wireless Bridge (TEW-310APB)
Wireless Internet Router/Access Point (TEW-311BRP)
Standards-BasedTechnology
The IEEE802.11b standard-based technology assures that the TRENDware
Products are interoperable with existing compatible 2.4GHz wireless
technology. This means you will be able to transfer large files quickly or even
watch a movie in MPEG format over your network without noticeable delays. The
technology works by using multiple frequencies in the 2.4GHz range at speeds
up to 22Mbps. TRENDware products will automatically sense the best possible
connection speed to ensure the greatest speed and range possible with the
technology.
Installation Considerations
Designed to go up to 1,312 feet (400 meters) outdoors and up to 328 feet (100
meters) indoors, the TRENDware TEW-310APB lets you access your network
with your laptop computer from virtually anywhere. Keep in mind,
However,that the number, thickness, and location of walls, ceilings or other
Download from Www.Somanuals.co8m. All Manuals Search And Download.
objects that the wireless signal must pass thru may limit range. Typical ranges
vary depending on the types of materials and any background RF (radio
frequency) noise in your home or business. The key to maximizing range is to
followthesebasicguidelines:
1. Keep the number of walls and ceilings between the wireless Access
Point and your receiving device to a minimum - Each wall or ceiling can
reduce your TRENDnet Wireless product's range from 3-90 feet (1-30
meters.) Position your Access Points, Internet Routers, and computers
sothatthenumberofwallsorceilingsisminimized.
2. Be aware of the direct line between Access Points, Internet Routers, and
computers. Awall that is 1.5 feet thick (.5 meters), at a 45-degree angle
appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks
over 42 feet (14 meters) thick! Try to make sure that theAccess Points
and Adapters are positioned so that the signal will travel straight through
awallorceilingforbetterreception.
3. Building Materials make a difference - Asolid metal door or aluminum
studs may have a negative effect on range. Try to position Access
Points, and computers with wireless adapters so that the signal passes
throughdrywalloropendoorwaysandnotothermaterials.
4. Make sure that the device's antenna is positioned for best reception by
using the software signal strength tools included with your product.
5. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical
devices or appliances that may generate extreme RF noise.
For the average home, signal range should not be an issue. If you experience
low or no signal strength in areas of your home that you wish to access, consider
positioning the Access Point in a location directly between the computers with
wireless adapters. AdditionalAccess Points can be connected to provide better
coverageinroomswherethesignaldoesnotappearasstrongasdesired.
Using radio frequency (RF) technology, WLANs (Wireless LocalArea Networks)
transmit and receive data over the air, minimizing the need for wired
connections. Thus, WLANs combine data connectivity with user mobility, and,
throughsimplifiedconfiguration, enablemovableLANs.
Download from Www.Somanuals.co9m. All Manuals Search And Download.
4. Getting Started
Right out of the box, with its default settings, the TEW-310APB will
automatically connect with other TRENDnet products.
For the price of a single IP Address from your Broadband Internet Service
provider you can share the Internet with all the computers on your local network,
without sacrificing speed or security, using TRENDware networking products.
IP ADDRESS
Please note: If you have a DHCP-capable router, please configure
the TEW-310APB to disable its DHCP Server and enable its DHCP
Client
If you need to assign IP Addresses to the computers on the network,
please remember that the IP Address for each computer must be in
the same IP Address range as all the computers in the network, and
the Subnet mask must be exactly the same for all the computers in the
network.
For example: If the first computer is assigned an IP Address of
192.168.0.2 with a Subnet Mask of 255.255.255.0, then the second
computer can be assigned an IP Address of 192.168.0.3 with a Subnet
Mask of 255.255.255.0, etc.
IMPORTANT: If computers or other devices are assigned the same IP
Address, oneormoreofthedevicesmaynotbevisibleonthenetwork.
An Infrastructure network contains an Access Point. The Infrastructure
Network example shown on the below contains the following TRENDnet
networkdevices:
WirelessAccessPoint (TEW-310APB) (DHCP enabled at default)
Ethernet Broadband Router (TW100-S4W1CA) (DHCP enabled at default)
Notebook computer with a wireless adapter (TEW-301PC)
Desktop computer with a wireless adapter (TEW-303PI)
Cable modem or DSL Modem
DHCP stands for Dynamic Host Configuration Protocol. It is a protocol
for assigning dynamic IP addresses “automatically”. With a DHCP-
capable gateway/router, there is no need to manually assign an IP
address to each computer in the network.
Download from Www.Somanuals.c1om0. All Manuals Search And Download.
Setting Up an Infrastructure Network
Please remember that TRENDware wireless devices are pre-configured to connect
together, rightoutofthebox, withthedefaultsettings.
You will need a broadband Internet access (Cable/DSL)
subscription.
1
Consult with your Cable/DSL provider for proper installation of the
modem.
2
Configure TEW-310APB. Refer to the Quick Installation Guide for
setting up the Access Point.
Note: If you already have a DHCP server (e.g. Internet Router) on the
network, please disable the DHCP Server function on the TEW-310APB.
3
If you are connecting a desktop computer in your network, you
can install the TRENDnet TEW-303PI wireless PCI adapter into
an available PCI slot. See the Quick Installation Guide included
with the TEW-303PI
4
If you are connecting a Notebook computer in the network, install
5
the drivers for the TEW-301PC wireless CardBus adapter into the
laptop computer. See the Quick Installation Guide included with
TEW-301PI for installation instructions.
After the configuration, connect the Access Point to your network.
If you have an Internet Router, connect it to the cable/DSL
6
Please refer to the following sections
of this manual for additional
information about setting up a
network:
Networking Basics- learn how to
check your IP Address; share printers
and files.
Using the Configuration Utility-
learn the settings you must use on
each computer in your network for
successful communication.
Fig. 4.1
Troubleshooting learn how to check
for the proper installation of the
network adapters' drivers and other
tips for troubleshooting the network.
Download from Www.Somanuals.c1om1. All Manuals Search And Download.
5. Using the Configuration Menu
The Configuration Menu for the TEW-310APB is web-based. When using the
configuration program, please consider the following:
You will need a JavaScript-enabled web-browser such as the Internet Explorer 4.0
orhigher, ortheNetscapeNavigator4.0orhigher.
The computer that you are using for initial configuration must setup to receive IP
address from DHCP server (or have an IP Address within the same range as the
IP Address of the TEW-310APB). The TEW-310APB has a default IPAddress of
192.168.1.1 with subnet mask 255.255.255.0 and DHCP Server function enabled.
If you are using an Internet router with its DHCP server enabled, please do not
connect the TEW-310APB to the network. You will need to configure the TEW-
310APB, disable its DHCP Server and enable the DHCP Client.
If you have static IP address for each network device, please prepare a computer
with DHCP client enabled and use this computer to configure the TEW-310APB's
IP address to fit your network.
Factory Default Setting for the TEW-310APB
ESSID
Channel
WEP
User Name
Password
IP Address
DHCP Server
DHCP Client
default
1
disabled
admin
admin
192.168.1.1
enabled
disabled
Configuration Menu
Whenever you want to configure your network or the TEW-310APB, you can
access the Configuration Utility by opening the web-browser and typing in the
IP Address of the TEW-310APB. The TEW-310APB default IP Address is
showninFig5.1.
Download from Www.Somanuals.c1om2. All Manuals Search And Download.
· Open the web browser
· Type in the IP Address of the
Access Point
(default http://192.168.1.1)
Fig. 5.1
(The IP Address shown in the example above is the default setting. Use this IP address
when connecting to a network consisting of other TRENDnet devices set to their default
settings. If you have changed the IP Address of the TEW-310APB to conform to a network
other than one with TRENDnet devices, at their default setting, then input that IP Address in
the web browser, instead of the default IPAddress shown.)
· Type admin in the User Name
field
· Type in admin in the Password
field
· Click OK
Fig. 5.2
Status Screen with Menu Bar
The Configuration window will
appear. Here the Status tab is
displayed. Click on View Log to see
the wireless clients connection
history.
First Page - displays the first page of
the Log
Last Page - displays the last page of
the Log
Previous - moves back one log page
Next - moves forward one log page
Clear - clears the log completely
Refresh - updates the log with the
latest information
Fig. 5.3
If you wish to change the default
settings, click on Basic Setting on
the menu bar.
Download from Www.Somanuals.c1om3. All Manuals Search And Download.
Basic Settings
you can make changes to the
following items:
AP name
SSID
Channel
WEPKey
Mode
Fig. 5.4
AP Name: You may choose to rename your Access Point, especially if you
have more than one Access Point on your network.
SSID: (Service Set Identifier) “default” is the factory setting. The SSID
is a unique name that identifies a network. All devices on a network must
share the same SSID name in order to communicate on the network. If you
choose to change the SSID from the default setting, input your new SSID
nameinthisfield. TheSSIDcanbeupto32charactersinlength.
Channel: Channel 1 is the default channel. Input a new number if you want
to change the default setting. All devices on the network must be set to the
samechanneltocommunicateonthenetwork.
WEP Encryption: Select 64-bit, 128-bit, or 256-bit to use WEP (Wired
Equivalent Privacy) on the network. All devices on the network, and the
Access Point, must share the same level WEP, and they must share the same
WEPkey.
Mode: The WEP key is generated from ASCII or HEX (Hexadecimal) entries
that are either 64, 128, or 256 bit in length. Select HEX for entering HEX
numbers 0 ~ 9 and alphabet A ~ F. Or select ASCII for entering any ACSII
characters. The number of characters that you can enter is depending on the
level of WEP Key. The higher the WEP key level, the more characters you
need to enter for the keys. For 64-bit key, you need to enter 10 HEX or 5ASCII
characters. 128-bit requires 26 HEX or 13 ASCII characters. 256-bit WEB key
needs58HEXor29ASCIIcharacters.
Hexadecimal digitsconsistofthenumbers0-9andthelettersA-F
ASCII (American Standard Code for Information Interchange) is a code
forrepresentingEnglishlettersasnumbersfrom0-127
Download from Www.Somanuals.c1om4. All Manuals Search And Download.
Click Apply if you have made any changes or additions.
Click Cancel to discard the changes.
IP Settings
Click on this tab to change
device's IP Addresses.
The default IP Address is
192.168.1.1
LAN IP: If you have a DHCP Server,
such as an Internet Router, on the
network, click Obtain IP
Automatically. Or you can
manually enter the IP address,
Subnet Mask, and Gateway by
clicking Fixed IP.
Fig. 5.5
If the Access Point's LAN IP range is different from the configuration
computer's IP range, the computer will not be able to enter the
configuration menu using web browser.
DHCP Server: Available only when LAN IP is Fixed IP. Click On to enable
the TEW-310APB to assign IP addresses to computers on the network.
Click Off to disable this feature.
IP Range: IP address range that the device will distribute (e.g. From
192.168.1.2 To 192.168.1.100). Available when DHCP Server is On.
Download from Www.Somanuals.c1om5. All Manuals Search And Download.
Advanced Settings
AP Mode
There are 4 modes available.
AP: Access Point mode. Bridge
wireless clients to wired Ethernet
network.
AP Client: Acts as a wireless client
and connects to a remote Access
Point. This is used to convert an
Ethernet device to Wireless Client.
Fig. 5.6
You must enter the remote AP's MAC addressin the Remote AP BSS ID.It is
best to use another TEW-310APB as the Remote AP, please find AP's LAN
MACaddress inthe Statuspageandenterithere.
(Note: When the device is set to AP Client mode, it no longer accepts
connection from any wireless clients.)
MAC Address (Media Access Control Address): A unique hardware
address that identifies a device on a network. It is assigned at the factory
and cannot be changed. Usually you will find this address on a sticker on
the device or on the packaging.
Wireless Bridge: Bridges two wired Ethernet networks together wirelessly
using two TEW-310APB. You must enter the Remote Bridge AP's MAC
address in the Remote Bridge MAC. It is best to use another TEW-310APB
as the Remote Bridge AP, please find AP's LAN MAC address in the Status
pageandenteritinRemoteBridgeMAC.
(Note: When the device is set to Wireless Bridge or Multiple Bridge
mode, it no longer accepts connections from any wireless clients.)
Multiple Bridge: Bridges multiple wired Ethernet networks together using
multiple AP. All AP must have the same ESSID and Channel number. It is
best to use TEW-310APB as the Bridging AP. Although there is no limit on
the numbers of AP you can bridge together, please keep in mind that all AP
share the 11Mbps wireless bandwidth. In Multiple Bridge environment, you
could also limit certain APs' bandwidth by setting their Supported Rate to
lower number (e.g. 1~2Mbps).
Beacon Interval: Beacons are packets sent by an Access Point to
synchronize a wireless network. Specify a Beacon interval value. Default
(100) is recommended.
Download from Www.Somanuals.c1om6. All Manuals Search And Download.
RTS Threshold: This value should remain at its default setting of 2,432. If you
encounter inconsistent data flow, only minor modifications to the value range
between256and2,432arerecommended.
Fragmentation: This value should remain at its default setting of 2,346. If
you experience a high packet error rate, you may slightly increase your
Fragmentation Threshold within the value range of 256 to 2,346. Setting
the Fragmentation Threshold too low may result in poor performance.
DTIM Interval (Beacon Rate): (Delivery Traffic Indication Message) Enter
a value between 1 and 16384 for the Delivery Traffic Indication Message
(DTIM.) A DTIM is a countdown informing clients of the next window for
listening to broadcast and multicast messages.
(Note: You could modify Beacon Interval, RTS Threshold, Fragmentation,
and DTIM Interval to fine-tune your wireless network, however, this takes
many trial and error and we recommend keeping them in their default
values.)
Authentication Type:
Open System: communicates the key across the network
Shared Key: devices must have identical WEP settings to communicate
Both automatically adjusts to the Authentication mode of the wireless client
All wireless devices must have the same Authentication Type. The default
setting is Both.
Preamble: The preamble defines the length of the CRC block for
communication between the Access Point and roaming Network Card.
Please select the appropriate preamble type and click the Apply button to
save the settings. (Note: High network traffic areas should use the shorter
preamble type. All wireless devices in the same network need to have the
same preamble setting.)
Basic Rate and Supported Rate: Select the desire bandwidth for the
wireless device. The Basic Rate is for factory trouble shooting purpose and
it will not affect the device's performance. Supported Rate is the true
bandwidth of the device. When the wireless signal is strong, set it at 1-2-
5.11-22(Mbps) to have the highest performance. When the signal is weak,
select 1-2(Mbps) to reduce transmission error.
Antenna Selection: Select which antenna you will use to receive data. The
default setting is Diversity (uses both antennas to receive data which help
overcome multi-path distortion).
Click Apply if you have made any changes or additions.
Click Cancel todiscardthechanges.
Download from Www.Somanuals.c1om7. All Manuals Search And Download.
Security
Password: Change the login User
Name and Password in this screen.
Administrator ID: This is the login
User Name for the browser
configuration. Default is admin, you
can enter a name with up to 15
characters.
AP Password New: Enter the new
password (up to 15 characters).
Fig. 5.7
Confirm:Enterthenewpasswordagain.
Click ApplytosavethenewUserNameandPassword.
Click Cancel todiscardthechanges.
MAC Filter: Use MAC Filters to allow or deny wireless connection to the
TEW-310APB. Select Enable to activate the filter, select Disable (default)
to disable this feature.
Select Only deny PCs with the MAC listed below to access the device
or select Only allow PCs with the MAC listed below to access the
device and enter the MAC Address of the selected computers into the
fields below.
You could enter up to 50 MAC address entries, but only 10 entries are
displayed. Please click on the 1~10 pull-down arrow and select the next 10
entries (21~30, 31~40, and 41~50).
Click Applytosavethesettings.
Click Cancel todiscardthechanges.
802.1X
802.1X Authentication protocol. This protocol is not available with the first
released firmware. Please check TRENDware web site
Download from Www.Somanuals.c1om8. All Manuals Search And Download.
Tools
Backup Settings: The current
device settings can be saved as a
file onto the local hard drive by
clicking Backup and then follow the
instructions on the screen to save
the configuration file to desired
Fig. 5.8
Restore Settings: The saved settings can be loaded back on the TEW-
310APB by entering the correct path or clicking Browse and locate the
correct saved file location. When you have selected the settings file, click
Restore to load the settings.
Restore to default settings: Click Default to return all settings back to
Factory Default Settings.
Firmware Upgrade: Upgrade the firmware for the Access Point. Please
download the new firmware for TEW-310APB. After you have downloaded
a firmware upgrade to your local drive, click Browse, select the firmware
file, and click Upgrade to perform the firmware upgrade. After that, go to
Status page and verify the new firmware version.
(Note: Please do not interrupt the firmware upgrade process.)
Download from Www.Somanuals.c1om9. All Manuals Search And Download.
6. Troubleshooting
BasedonWindowsXPOperatingSystem
This chapter provides solutions to problems that can occur during the installation
and operation of the TEW-310APB Wireless Access Point. We cover various
aspects of the network setup, including the network adapters. Please read the
following if you are having problems.
Note: It is recommended that you use an Ethernet connection to
configure the TEW-310APB Access Point.
1.The computer used to configure the TEW-310APB cannot access the
Configuration menu.
· Check that the Ethernet LED on the TEW-310APB is ON. If the
LED is not ON, check that the cable for the Ethernet connection is
securely inserted.
· Check that the Ethernet Adapter is working properly. Please Check
that the drivers for the network adapters are installed properly
· Check that the IP Address is in the same range and subnet as the
TEW-310APB. Please see Checking the IP Address in Windows
XP in the Networking Basics section of this manual.
Note: The IP Address of the TEW-310APB is 192.168.1.1. All the computers on the
network must have a unique IP Address in the same range, e.g., 192.168.1.x. Any
computers that have identical IP Addresses will not be visible on the network. They
must all have the same subnet mask, e.g., 255.255.255.0
· Do a Ping test to make sure that the TEW-310APB is responding.
Go to Start>Run>Type Command>Type ping 192.168.1.1. A
successful ping will show four replies.
Fig. 6.1
Download from Www.Somanuals.c2om0. All Manuals Search And Download.
2. ThewirelessclientcannotaccesstheInternetinthe
Infrastructure mode.
· Make sure the wireless client is associated and joined with the correct
Access Point. To check this connection: Right-click on the Local
Area Connection icon in the taskbar> select View Available Wireless
Networks. The Connect to Wireless Network screen will appear.
Please make sure you have selected the correct available network, as
shown in the illustrations below.
Fig. 6.2
You could also check the associated Access Point by using your
Wireless Adapter's Utility program.
· Check that the IP Address assigned to the wireless adapter is within
the same IP Address range as the access point and gateway. Since
the TEW-310APB has an IP Address of 192.168.1.1, wireless
adapters must have an IP Address in the same range, e.g.,
192.168.1.x. Each device must have a unique IP Address; no two
devices may have the same IP Address. The subnet mask must be the
same for all the computers on the network.) To check the IP Address
assigned to the wireless adapter, double-click on the Local Area
Connection icon in the taskbar > select the Support tab and the IP
Address will be displayed. (Please refer to Checking the IP Address
in the Networking Basics section of this manual.)
· If it is necessary to assign a Static IP Address to the wireless adapter,
please refer to the appropriate section in Networking Basics. If you are
entering a DNS Server address you must also enter the Default
GatewayAddress.
Download from Www.Somanuals.c2om1. All Manuals Search And Download.
3. Check that the drivers for the network adapters are installed properly.
You may be using different network adapters than those illustrated here,
but this procedure will remain the same, regardless of the type of network
adapters you are using.
· Go to Start
· Right-click on My Computer
· Click Properties
(If the “My computer” icon is
on your desktop, you can
simply right click on it and
click on “Properties”)
Fig. 6.3
· Select the Hardware Tab
· Click Device Manager
Fig. 6.4
Download from Www.Somanuals.c2om2. All Manuals Search And Download.
· Double-click on Network
Adapters
· Right-click on 22M Wireless
Cardbus Adapter
· Select Properties to check
that the drivers are installed
properly.
Fig. 6.5
· Look under Device Status
and check that the device is
working properly.
· Click OK to close this
window.
Fig. 6.6
Download from Www.Somanuals.c2om3. All Manuals Search And Download.
4. Resetting the TEW-310APB to Factory Default Settings
After you have tried other methods for troubleshooting your network, you
may choose to Reset the TEW-310APB to the factory default settings.
Remember that TRENDnet wireless products network together, out of the
box, at the factory default settings.
To hard-reset the TRENDnet TEW-310APB to Factory Default Settings,
pleasedothefollowing:
· Locate the Reset button on the back of the TEW-310APB (next to the
Ethernetport).
· UseapapercliptopresstheReset button.
· Holdforabout5secondsandthenrelease
· After the TEW-310APB reboots (this may take a minute) it will be
resettothefactory Default settings.
Download from Www.Somanuals.c2om4. All Manuals Search And Download.
7. Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work, using
MicrosoftWindowsXP.
Go to Start > Control Panel > Network Connections
Select Setupahomeorsmallofficenetwork
Fig. 7.1
Whenthisscreenappears, click Next.
Download from Www.Somanuals.c2om5. All Manuals Search And Download.
Pleasefollowalltheinstructionsinthiswindow:
Fig. 7.2
Click Next
In the following window, select the best description of your computer. If your
computer connects to the Internet through a gateway/router, select the second
optionasshown.
Fig. 7.3
Click Next
Download from Www.Somanuals.c2om6. All Manuals Search And Download.
Entera Computerdescriptionanda Computername.
Fig. 7.4
Click Next
(Note:EachcomputershouldhaveauniqueComputername)
Enter a Workgroupname. All computers on your network should havethe same
Workgroup name.
Fig. 7.5
Click Next
Download from Www.Somanuals.c2om7. All Manuals Search And Download.
Pleasewaitwhilethewizardappliesthechanges.
Fig. 7.6
Whenthechangesarecomplete, click Next.
Please wait while the wizard configures the computer.
This may take a few minutes.
Fig. 7.7
Download from Www.Somanuals.c2om8. All Manuals Search And Download.
In the window below, select the best option. In this example, Create a
Network Setup Disk has been selected. You will run this disk on each of the
computers on your network. Click Next.
Fig. 7.8
InsertadiskintotheFloppyDiskDrive, inthiscasedrive A:
Fig. 7.9
Formatthediskifyouwish, andclick Next.
Download from Www.Somanuals.c2om9. All Manuals Search And Download.
Please wait while the wizard copies the files.
Fig. 7.10
Please read the information under Here's how in the screen below. After you
complete the Network Setup Wizard you will use the Network Setup Disk to
run the Network Setup Wizard once on each of the computers on your network.
Tocontinue, click Next
Fig. 7.11
Download from Www.Somanuals.c3om0. All Manuals Search And Download.
Please read the information on this screen, then click Finish to complete the
Network Setup Wizard.
Fig. 7.12
The new settings will take effect when you restart the computer. Click Yes to
restartthecomputer.
Fig. 7.13
You have completed configuring this computer. Next, you will need to run the
Network Setup Disk on all the other computers on your network. After running
the Network Setup Disk on all your computers, your new wireless network will
bereadytouse.
Download from Www.Somanuals.c3om1. All Manuals Search And Download.
Naming your Computer
Tonameyourcomputer, pleasefollowthesedirections:
InWindowsXP:
· Click Start(in the lower left corner
ofthescreen)
· Right-click on My Computer
· Click Properties
(If the “My computer” icon is on your
desktop, you can simply right click on
itandclickon“Properties”)
Fig. 7.14
·Select the Computer Name Tab
in the System Properties
window.
You may enter a Computer
description if you wish; this field is
optional.
To rename the computer or join a
domain,
· Click Change
Fig. 7.15
Download from Www.Somanuals.c3om2. All Manuals Search And Download.
· In this window, enter the
Computer name.
· Select Workgroup and enter the
name of the Workgroup.
· All computers on your network
must have the same Workgroup
name.
· Click OK
Fig. 7.16
Checking the IP Address in Windows XP/2000
Go to Start > All Programs > Accessories > Command Prompt
Fig. 7.17
Download from Www.Somanuals.c3om3. All Manuals Search And Download.
Type Command and click OK
Fig. 7.18
Type ipconfig /all and hit Enter at the prompt. All the configuration
settings are displayed as shown below.
Fig. 7.19
Type ipconfig /renew at the prompt to get a new IP Address, shown
below.
Fig. 7.20
(Windows 98/ME users: go to Start > Run. Type Command. Type
winipcfg at the prompt. Click Release and Renew to obtain a new IP
Address.)
Download from Www.Somanuals.c3om4. All Manuals Search And Download.
Assigning a Static IP Address
Note: Residential Gateways/Internet Routers will automatically assign IP
Addresses to the computers on the network, using DHCP (Dynamic Host
Configuration Protocol) technology. If you are using a DHCP-capable
Gateway/Router you will not need to assign Static IPAddresses, however, you
need to set the TCP/IP protocol to automatically obtain IP.
F you are not using a DHCP capable Gateway/Router, or you need to
assignaStaticIPAddress, pleasefollowtheseinstructions:
· Go to Start
· Double-click on
Control Panel
Fig. 7.21
·Double-click on
Network Connections
Fig. 7.22
Download from Www.Somanuals.c3om5. All Manuals Search And Download.
·Right-click on Local Area
Connections.
·Click Properties
Fig. 7.23
· Highlight Internet Protocol
(TCP/IP)
· Click Properties
Fig. 7.24
Download from Www.Somanuals.c3om6. All Manuals Search And Download.
· Select Use the following IP address in the Internet Protocol
(TCP/IP) Properties window,
· Input your IP address and subnet mask. (The IP Addresses on your
network must be within the same range. For example, if one computer
has an IP Address of 192.168.0.2, the other computers should have IP
Addresses that are between 192.168.0.3 and 192.168.0.254. No two
computes can have the same IP Address. The subnet mask must be the
same for all the computers on the network.)
· Input your DNS server address only if you plan to use the Internet.
(Note: If you are entering a DNS server address, you must also enter the IP
Address of the Default Gateway.)
The DNS server information will be provided by your ISP (Internet
Service Provider.)
Fig. 7.25
·Click OK
YouhavecompletedtheassignmentofaStaticIPAddress.
Download from Www.Somanuals.c3om7. All Manuals Search And Download.
Connecting to a Wireless Network in Windows XP
To be able to connect to a wireless network, make sure the proper network
settings are configured for TEW-303PI.
· Go to Start > right-click on My
NetworkPlaces >
· Select Properties > double-
click on the Wireless
Network Connection
associated with the 22M
wireless Adapter >
· Select Properties > select
Internet Protocol (TCP/IP) >
click Properties
Fig. 7.26
Connecting to a Wireless Network with a Wireless Router or an
AccessPointusingaDHCPserverinWindowsXP.
· Select Obtain an IP address
automatically - if the Wireless
Router or Access Point has
DHCP server enabled
· Select Obtain DNS server
address automatically.
· Click OK
Fig. 7.27
Download from Www.Somanuals.c3om8. All Manuals Search And Download.
Connecting to a Wireless Network with a Wireless Router or an
Access Point using a static IP address in Windows XP.
Select Use the following IP address - if the Wireless Router or Access Point
does nothave a DHCP server enabled.
· Input a static IP address within the
same range as the Wireless
Router or Access Point.
· IP address: 192.168.0.51
· Subnet mask: 255.255.255.0
· Default Gateway: Enter the LAN
IP address of the Wireless
Router
· Select Use the following DNS
server address. Enter the ISP
provided DNS addresses.
· Click OK
Fig. 7.28
Connecting to a Wireless Network in Windows 2000
· Go to Start > Settings > Network
and Dial-up Connections >
Double click on the Local Area
Connection associated with the
22M Wireless Adapter > select
Properties > select Internet
Protocol (TCP/IP) > click
Properties
Fig. 7.29
Download from Www.Somanuals.c3om9. All Manuals Search And Download.
Connecting to a Wireless Network with a Wireless Router or an
AccessPointusingaDHCPserverinWindows2000.
· Select Obtain an IP address
automatically.
· Select Obtain DNS server
address automatically.
· Click OK
Fig. 7.30
Connecting to a Wireless Network with a Wireless Router or an
Access Point using static IP address in Windows 2000.
· Select Use the following IP
address
· Input a static IP Address
within the same IP Address
range as the wireless router
or the access point.
· IP address: 192.168.0.51
· Subnet mask: 255.255.255.0
· Default Gateway: Enter the
LAN IP address of the
Wireless Router
· Select Use the following
DNS server address. Leave
this section blank.
Fig. 7.31
· Click OK
Download from Www.Somanuals.c4om0. All Manuals Search And Download.
ConnectingtoaWirelessNetworkinWindowsMeand98
· Go to Start > Settings >
Control Panel > Double-click
on the Network associated
with the 22M Wireless
Adapter > click Properties >
select Internet Protocol
(TCP/IP) > click Properties
Fig. 7.32
Connecting to a Wireless Network with a Wireless Router or an
Access Point using a DHCP server in Windows Me and 98.
· Select the IP Address tab.
Then, select Obtain an IP
address automatically.
· Select Detect connection to
network media.
· Click OK
Fig. 7.33
Download from Www.Somanuals.c4om1. All Manuals Search And Download.
Connecting to a Wireless Network with a Wireless Router or
Access Point using a static IP address in Windows Me or
Windows 98.
· Select Specify an IP address.
· Input a static IP address within
the same IP Address range as
the wireless router or access
point.
·IPaddress:192.168.0.51
·Subnetmask: 255.255.255.0
· Default Gateway: Enter the
LAN IP address of the
Wireless Router
· Select Detect connection to
networkmedia.
Fig. 7.34
Checking the Wireless Connection by Pinging
For Windows XP and 2000:
· Go to Start > Run > type
cmd. A window similar to
Fig. 7.35 will appear.
· Type ping xxx.xxx.xxx.xxx
and hit Enter, where xxx is
the IP address of the
Wireless Router or Access
Point.
Fig. 7.35
· A good wireless connection
will show four replies from the
wireless router or access
point, as shown.
· Click OK
Download from Www.Somanuals.c4om2. All Manuals Search And Download.
For Windows Me and 98:
· Go to Start > Run > type
command. A window similar
to Fig. 7.36 will appear. Type
ping xxx.xxx.xxx.xxx, where
xxx is the IP address of the
Wireless Router or Access
Point. A good wireless
connection will show four
replies from the wireless
router or access point, as
shown.
Fig. 7.36
File and Printer Sharing
For help with other tasks in home or small office networking, see Using the
Shared Documents folder and Sharing files and folders in the Help and
SupportCenterinMicrosoftWindowsXP.
Download from Www.Somanuals.c4om3. All Manuals Search And Download.
8. Technical Specifications
Standards
· IEEE802.11b
· IEEE 802.3
· IEEE802.3u
Ports
· (1)10/100Base-TEthernet, RJ-45(UTP)
· (1)Power 5VDC, 2.0A
NetworkManagement
· Web-BasedbrowserwithJavaScript
FrequencyRange
· 2.4 ~2.4835GHz, DirectSequenceSpreadSpectrum(DSSS)
DataRates (Mbps:Channel)
· 22:PBCC
· 11:PBCC/CCK
· 5.5:PBCC/CCK
· 2: Barker
· 1: Barker
DataSecurity
· 64, 128, 256-bitWEP(WiredEquivalentPrivacy)Encryption
· AccessControlList
DiagnosticLED
· Power
· Link
· TX/RX
AntennaType
· Diversity
Range
· Indoors upto328feet(100meters
· Outdoors upto1,312feet(400meters)
Download from Www.Somanuals.c4om4. All Manuals Search And Download.
Dimensions
· 140x113x38mm(5.51x4.45x1.50inches)(antennafolded)
· 140x113x108mm(5.51x4.45x4.25inches)(antennafullyerected)
Weight
· 213grams(7.5Oz.)
Temperature
· Operating:-10ºCto55ºC(14ºFto131ºF)
· Storing:-20ºCto65ºC(-4ºFto149ºF)
Humidity:
· 5%-95%, non-condensing
Emissions:
· FCCpart15b
· UL1950-3
Download from Www.Somanuals.c4om5. All Manuals Search And Download.
9. Contacting Technical Support
You can find the most recent software and user documentation on the
TRENDware provides free technical support for customers within the United
States for the duration of the warranty period on this product.
U.S. customers can contact TRENDware technical support through our web site,
bye-mail, orbyphone.
TRENDwareTechnicalSupportovertheTelephone:
Tel:+1-310-891-1100
TRENDwareTechnicalSupportE-mailAddress:
When contacting technical support, please provide the following information:
·Serial number of the unit
·Model number or product name
·Software type and version number
Download from Www.Somanuals.c4om6. All Manuals Search And Download.
|
