USDT 2004B
Installation and User’s Guide
Introduction
General Information
2
Installation
Collector Sensor
3
5
6
6
Control Box
Power Connection
Display Window
Operation
Basic Operation of Digital Display
Programming the Temperature Range
Manual Operation Mode
Troubleshooting
6
8
9
10
ã Thermo Technologies
5560 Sterrett Place • Suite 115
Columbia, Maryland 21044
Phone 410.997.0778 • Fax 410.997.0779
e-Mail [email protected]
Basic Revision 8, January 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Note: This installation procedure is for guidance only, and the installer should verify its
suitability. Make sure that the solar system is physically installed, manually tested, and ready for
controlled operation.
he following safety precautions is strongly recommended:
T
1. Before attempting to install and operate the unit read this instruction manual carefully.
2. Only suitably qualified personnel should carry out installation and required maintenance.
3. It is recommended that the unit be connected to the power supply via an on/off switch or plug.
4. WARNING: When the unit is connected to the 115-volt power supply and the cover is
opened, high voltage circuits will be exposed.
When installing the unit, all required
connections should be completed and the cover attached to the controller box before turning
the power on. Ensure that all connections are secure. If any maintenance work is required
isolate the unit from the power supply before removing the cover. Never leave the unit
unattended if the cover has been removed and the power supply is connected.
5. Do not exceed unit ratings of 3.15 amps (1/6HP or 245 Watts).
6. It is advisable to route power cables away from sensor cables.
ensor installation: Temperature sensors may be installed with fluid lines by mounting in a
well or strapping it to the piping directly. For the system to function correctly, it is essential
that the sensors are located and installed properly. Sensors must be well insulated in order to
prevent them from being influenced by the ambient temperature.
When used outdoors, water must not enter the immersion sleeves. Exposure to moisture (e.g.
condensation) can diffuse through the cast resin and damage the sensor.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
l
Collector sensor (red cable with protective terminal box): Either push into a thermowell,
(sensor pocket), which is soldered or riveted directly to the manifold (vacuum tubes). Alternately,
strap the sensor to the collector outlet pipe or the absorber (flat plate collectors) that projects from
the collector housing. Ideally, house the collector sensor (encased in a suitable sensor pocket)
into a T-piece on the collector return outlet. Protect the sensor cable from UV and moisture.
l
Return (tank) sensor (white cable): The sensor required for the solar loop return is installed
in the lower part of the storage tank. If there is no provision for this tank sensor, push the sensor
beneath the insulation – keeping it close to the inner tank wall at the desire tank location.
For external heat exchangers, the tank sensor should be installed with an immersion sleeve in the
return leg (cold side) of the heat exchanger. In tanks with integrated heat exchangers, the sensor
pocket should be fitted at the exchanger's return to the collector.
l
Sensor cable extension: Sensor cables (22/4 AWG telephone cable, you need only two
wires of 4) can be extended up to 150 ft. A connection between the sensor and extension can be
established as follows:
Cut the supplied heat-shrinkable tubing to desired length (about ½ ”). Slide tubing over one end of
wire to be sliced (after removing enough outer insulation to accept the tubing). Splice the wire
and slide tubing over the splice. Heat gently all around until tubing shrinks tight.
Slide larger tubing (about ¾ “) over the entire completed splice. Heat gently all around until tubing
shrinks tight. This connection can then be drawn gently into the pipe work. Only two of the wires
are required for the sensor cable; the other two wires are spare wires.
Caution: Do not overheat the tubing! Remove heat as soon as the tubing shrinks tight, as
material will continue to shrink. With flame source, use even back and forth motion all around
tubing. A heat gun may be used, if available. Let tubing cool for maximum strength.
ontroller unit installation: For viewing comfort, the controller unit should be positioned
at eye level. For optimum longevity, avoid extremes of temperature in the placement of
electronic equipment. In addition, avoid heavy electrical loads, switches or contactors as these
may cause electrical and electromagnetic interference with the unit (when switched on or off).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Undo the screw at the top of the housing. The control electronics are mounted on the enclosure
cover. The controller enclosure can be screwed to the wall with cable entry grommets pointed
downwards. Use the supplied plastic bridges to secure power and sensor cables.
Base of the unit to be mounted at eye-level and wired as shown above
Caution: Controller wiring should only be done when the unit is not energized. It is possible to
damage the control unit if it is assembled under voltage. Miniaturized terminal blocks are used for
making wiring connections. The wire is held in place within the terminal with screw that provides
excellent contact without damage to the wire.
Sensor Cable Connection: Use up to an 18 AWG stranded wire to connect the sensor cables to
the unit. The S1 terminal should be connected to the collector sensor (higher temperature); the
S2 terminal is designated for the tank sensor (lower temperature).
The S3 terminal is reserved for advanced usage and should remain vacant for the basic program.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ower Connections: A small blade screwdriver may be used to fasten miniaturized
terminal block screws while the corresponding wire is inserted.
NOTE 1: Always disconnect the controller from power supply before opening the housing.
NOTE 2: The controller should be properly grounded. Flexible wires, 18/3 AWG
(gauge/conductor) simplify connection to the terminals. The power terminal block will
accommodate wire sizes to 14 AWG. All other connections should be secured and adequately
tightened, as loose power connections will over-heat, and may cause fire.
NOTE 3: It is important that the specified output loads (245 Watts) are not exceeded. Where
these loads expect to exceed, external relays must be used. It is good practice to install a switch
to disconnect the controller and pump from power. Always keep power cables away from sensor
cables and other low voltage signal cables.
NOTE 4: To protect against lightening damage, the system must be grounded according local
regulation. Sensor failures due to the weather or electrostatic are mostly due to poor grounding.
BASIC OPERATION OF DIGITAL
DISPLAY
our controller displays requested information one at a time. The unit display window
has three lines to inform you about the system's status, unit of displayed parameter
and its value.
Upper Line Display
Center Line Display Sensor ID and its reading in normal mode (user interface window)
Lower Line Display Set-point indicator that illuminates only during programming mode
Symbolic display of sensor location, reading unit, and operation domain
ð
ï
Push selection key once to move to the next selection; or increase the selected
parameter by one unit.
Push selection key once to move to the previous selection; or decrease the selected
parameter by one unit.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ò
ñ
Push selection key once to enter the advanced (Par or *Men) mode. Once in selected
mode, press one more time to select the parameter in that mode. Selected parameter
blinks allowing the user to modify it. You can modify the selected parameter while the
middle window blinks by pressing the ïor ðkey.
Push selection key once to accept selection (blinking stops showing the new set-point
steady) or go back to the previous selection.
(*) USDT 2004B does not support “Men” mode operation.
Use selection keys ïðduring normal system operation to display the desired parameter:
o
T1 xxx
T2 xxx
T3 250
XX xxx
YY xxx
ZZ xxx
GAL 60
Collector temperature in F
Tank temperature in F
o
Displays a fixed reference temperature of 250oF.
Collector power in [kW] – amount of energy collector is producing
Energy collected in [MWh]
Energy collected in [kWh]
Flow rate [gallon/h] – a fixed rate of 1.0 gpm ex factory
Example: Following chart displays system temperatures
At the upper text line, the icon for the text is always displayed. Program symbol is displayed
during the setting of parameters at the lower text line. In addition, an arrow icon > is displayed
while pump is running.
For Programming - Pressing the selection key ðseveral times allows you to enter into the
program mode (Par). Push selection key òonce to enter the program mode.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Par
Using the navigation key ^_ allows you to select the desired parameter while you are in
the program mode. Press the selection key òonce to select the parameter in the window.
Selected parameter blinks allowing you to modify it. You can modify the selected parameter
while the middle window blinks by pressing the ïor ðkey. The unit accepts the new value by
pressing the ñkey once.
RUV 2.0 – This display shows the software revision number.
NR O – This indicates the USDT 2004B employment as a basic solar hot water heating controller.
PROGRAMMING THE TEMPERATURE RANGE
o
o
USDT 2004B is factory set at T2 > 160 F PUMP OFF, T2 < 150 F PUMP ON. The user may
program a different temperature range (hysteresis bandwidth) if required. In this case, there are
two temperatures that should be entered:
Tank Overheating Protection
User can program hysteresis (temperature range for output control) by using max? and max=.
For
max?1
Pump stops above tank temperature (T2)
max=1
Pump runs again below this set point (T2)
Temperature Differential Adjustment
diff=1
Pump runs when temperature difference between collector T1 (collector) and T2
(tank) exceeds this value. Factory setting is 15 oF. Consult your collector
manufacturer for the recommended value.
diff?1
Pump stops when temperature difference between collector T1 (collector) and T2
(tank) reaches this value. Factory setting is 7 F. Consult your collector
o
manufacturer for the recommended value.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Operation Mode
This mode allows the user to manually turn the pump on or off.
AUTO
The above display indicates that the unit is working in automatic mode. The
pump starts at a temperature difference of 15 oF and runs as long as ? T is
above 7 oF. The B symbol appears in upper display line next to the collector
symbol while the pump is running. User can switch to manual mode by pressing
òkey. By pressing ðkey while centerline blinks, a hand symbol Gin lower line
shows manual operation. Pressing ðone more time lets you turn the pump ON or
OFF. By pressing ñkey you change the pump operation.
ensor Designation – The factory-preset sensor is the thermistor (KTY) type. The KTY
tank sensor, white wire, should be used in a conditioned environment and will not be
permanently damaged up to 360 F.
o
S1
S2
Sensor 1 (collector outlet)
Sensor 2 (collector inlet or bottom of the tank)
Sensor wires can receive electromagnetic pulses, which can result in a wrong temperature
reading. The USDT 2004B reads sensor values every 50 ms. It can bundle several readings and
process their average.
The impedance characteristics of the USDT 2004B sensors (temperature dependencies) are
represented in the following table:
T
0
10
20
25
30
40
50
60
70
80
90
100°C
R(KTY) 1630 1772 1922 2000 2080 2245 2417 2597 2785 2980 3182
3392 W
9
Download from Www.Somanuals.com. All Manuals Search And Download.
roubleshooting
T
In general, all of the settings in the menus Par and Men and the terminal should first be checked
if there is a malfunction.
Malfunction, but "realistic" temperature values:
·
·
Check program number. It should be “0” (zero) for 2004B unit.
Check the switch-on and switch-off thresholds and the set differential temperatures, page
8. Have the thermostat and differential thresholds already been reached?
Can the pump (output) be switched on and off in manual mode? If a forced pump “ON”
and “OFF” lead to the appropriate reaction at the output, the unit is certainly in order.
Are all of the sensors connected to the right terminals? Heat up the sensor using a
cigarette lighter and watch the display.
·
·
Incorrect display of temperature(s):
·
·
-999 sensor short-circuit
999 no sensor reading - (open loop) interruption do not necessarily mean a material or
terminal error.
Overheating protection:
The Circulation pump may not be powerful enough to circulate the heat transfer fluid in the
solar loop with air pockets. To protect the pump, USDT 2004B will take over the normal
operation after the temperature decreases to an acceptable working temperature.
The sensor can also be checked without a measuring instrument by connecting the presumed
defective sensor to a terminal that works and checking the display. The resistance measured by
an ohmmeter should have the impedances shown in page 9.
The settings of the parameters and menu functions ex works can be restored any time by
pressing the down arrow (enter) while powering the controller. The sign that appears for three
seconds on the display is RESTOR for load factory settings.
If the system is not in operation while connected to the power supply, the 3.15A quick-blowing
fuse that protects the control system and the output should be checked and exchanged if
necessary.
As the programs are constantly being improved, there may be a difference in the sensor and
program descriptions. Only the enclosed manual (identical serial number) applies for the
equipment supplied. The program version for the manual must correspond to the equipment
version.
If the control system is found to be malfunctioning despite the checks described above, please
contact your retailer or Thermo Technologies directly. The cause of the error can only be
determined if the settings of the unit is known. The schematic diagram of the system in question
is a great help to isolate the potential problem.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|