OPERATING INSTRUCTIONS
LINE ARRAY SPEAKERS
SR-S4L
SR-S4S
EXTENSION PLATE (optional)
SR-EP4
SR-PP4
PROTECTION PAD (optional)
SR-S4S
SR-S4L
Thank you for purchasing TOA's Line Array Speakers and their associated products.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
WARNING
When Installing the Unit
• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.
Doing so may result in the unit falling down and causing personal injury and/or property damage.
• Refer all installation work to the dealer from whom the speaker was purchased. Installation requires
extensive technical knowledge and experience. The speaker may fall off if incorrectly installed, resulting in
possible personal injury.
• Flying Precautions
Be sure to follow the instructions below. Otherwise, the suspension wires or belts may be off or snap and
the speaker may fall off, causing personal injury.
· Check to confirm that the suspension wires and belts are strong enough to withstand the speaker load.
· The connectors of the suspension wires and belts must be securely linked with those of the speaker.
· All parts and components (such as enclosures, metal pieces, and screws) must be free from any
deformation, crack, and corrosion.
· Be sure to use screws supplied with the optional flying hardware when installing the speaker using such
hardware.
• Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket.
Doing otherwise may result in the unit falling down and causing personal injury and/or property damage.
• Owing to the unit's size and weight, be sure that at least two persons are available to install the unit. Failure
to do so could result in personal injury.
• Do not use other methods than specified to install the speaker. Extreme force is applied to the unit and the
unit could fall off, possibly resulting in personal injuries.
• Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so
may cause the speaker to fall, resulting in material damage and possible personal injury.
• Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent
accidents that could result in personal injury.
• Use the specified mounting bracket in combination. Doing otherwise may cause the unit or component to fall
off, resulting in personal injury.
• Do not mount the unit in locations exposed to constant vibration. The mounting bracket can be damaged by
excessive vibration, potentially causing the unit to fall, which could result in personal injury.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
CAUTION
When Installing the Unit
• Avoid placing the unit in a doorway or other high traffic area as people may trip on the equipment and cords,
or be injured by falling objects.
• Avoid touching the unit's sharp metal edge to prevent injury.
• When installing the speaker at head height, attach the optional SR-PP4 Protection Pad to the bottom of the
speaker. Failure to do so may cause injury if people hit their heads directly against the speaker.
When the Unit is in Use
• Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate and result in a fire.
• Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in
personal injury and/or property damage.
• Have the unit checked periodically by the shop from where it was purchased. Failure to do so may result in
corrosion or damage to the unit or its mounting bracket that could cause the unit to fall, possibly causing
personal injury.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. GENERAL DESCRIPTION
Featuring slim construction, the SR-S4 series are 2-way line array speakers containing 32 speaker elements.
The sound source speaker elements are vertically arranged in close proximity to each other, and form a
continuous linear sound source, achieving uniform sound pressure with less attenuation due to distance.
The SR-S4L speaker is of a linear design which is ideal for long distance sound transmission applications,
while the SR-S4S features a curved line having a 10° vertical coverage area, and is designed to cover
relatively short distance applications.
It is also possible to combine both the linear and curved line types to configure an array that continuously
covers applications ranging from short to long distances.
3. FEATURES
• The SR-S4 series is a 2-way line array speaker having eight 10 cm woofers for low-frequency output, and 24
small tweeters for high-frequency sound output. Both the woofers and tweeters are arranged in the front and
rear on the same axis, providing a symmetrical, uniform coverage area.
• Since the linear sound source effect prevents energy from attenuating even at longer distances, the line
array speaker compares favorably with normal types of speakers in its ability to project sound long
distances. This realizes less difference in sound volume between areas close and far from the speaker, for a
more uniform sound field.
• Since the speaker's vertical sound dispersion is suppressed, sound is only directed at the target area. The
speaker's construction is not influenced by sound reflection from ceiling or floor surfaces, and can provide
clear sounds even in spaces affected by long reverberation times or other poor acoustic conditions.
• Since the attenuation of sound pressure is small even far away from the speaker, the volume is not
excessively loud in the area near the speaker. This helps suppress feedback (improving safety amplification
gain).
• By joining 2 or 3 speakers, a longer sound source can be configured, making it possible to project sound
output farther and at larger volumes.
• The speaker has a built-in network circuit for a single amplifier drive. Changing the internal connector
position enables bi-amplifier drive that provides a higher quality sound output.
• The use of optional mounting brackets* permits the speaker to be installed in the most appropriate position
for its intended use. (Details of the installation procedures are described in the installation manual enclosed
with each bracket.)
* SR-WB4 Wall mounting bracket, SR-TB4 Wall tilt bracket, SR-FB4 Flying bracket, SR-SA4 Stand adapter,
and SR-FS4 Floor stand.
• The speaker can be used for high-impedance applications with the additional use of the optional MT-S0601
Matching transformer. (Single-amplifier drive only)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. COVERAGE AREA
The line array speaker radiates a sound only within a limited range.
Since sound is reduced in areas that are outside the range, take care that the listening area is sufficiently
covered when installing the speaker.
• Correct installation examples
[SR-S4L x 2]
[SR-S4S]
[SR-S4L + SR-S4S]
• Incorrect installation examples
If the speaker is installed high above the floor facing horizontally or diagonally downward at a large angle, the
listening area cannot be covered sufficiently.
[SR-S4L]
[SR-S4S]
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. DIMENSIONAL DIAGRAM
5.1. Line Array Speaker SR-S4L
Unit: mm
255
100 50
160
[Front]
[Side]
[Rear]
Blank panel
(The optional MT-S0601
Matching Transformer
can be installed inside.)
60
Input terminal panel
100 50
5.2. Line Array Speaker SR-S4S
Unit: mm
255
100 50
160
[Front]
[Side]
[Rear]
Blank panel
(The optional MT-S0601
Matching Transformer
can be installed inside.)
Input terminal panel
303
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. SINGLE-AMPLIFIER DRIVE AND BI-AMPLIFIER DRIVE
The SR-S4 series speakers are factory-preset to be driven by a single amplifier, however this setting can be
changed to a bi-amplifier drive system by changing the speaker's internal wiring.
(See p. 12; Changing Single-Amplifier Drive to Bi-Amplifier Drive System.)
• Single-amplifier drive
Note: Use a digital processor as required.
LOW
Woofers
Passive
network
x
8
HIGH
Mixer/preamplifier
Digital processor
Power amplifier
Tweeters
x
8
SR-S4L/S4S
• Bi-amplifier drive
LOW
LOW
HIGH
Woofers
x
8
HIGH
Mixer/preamplifier
Digital processor
Tweeters
Power amplifier
x
8
SR-S4L/S4S
7. INTERNAL WIRING DIAGRAM
When shipped from the factory, the speaker is internally connected as shown below.
Woofers
Screw terminals
Neutrik NL4MP connectors
Passive
network
INPUT +
INPUT –
1+
1+
2–
1–
2–
1–
x 4
THROUGH
THROUGH
2+
2+
Tweeters
Input terminal panel
x 4
• Since the Neutrik NL4MP connectors and screw terminals are internally connected in parallel, either one can
be used for connection.
• The Neutrik NL4MP connector's pins are wired
as shown at right.
The connector (connection cable side) suited to
the Neutrik NL4MP is the Neutrik NL4FC.
Pin No. SR-S4L, SR-S4S Screw terminal indication
1 +
1 –
2 +
2 –
Speaker +
Speaker –
INPUT +
INPUT –
THROUGH
THROUGH
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. CHANGING TO HIGH IMPEDANCE
The SR-S4 series speakers can be used for high-impedance applications with the installation of the optional
MT-S0601 Matching Transformer.
SR-S4L/S4S
To install the MT-S0601 transformer, remove the blank panel
Rear panel
located on the speaker's rear panel.
For details regarding mounting procedures, refer to the
instruction manual enclosed with the MT-S0601.
Note
The speaker cannot be used in combination with the matching
transformer when driven by a bi-amplifier.
Blank panel
INPUT
Pin 1+
THROUGH
Pin 2+
Pin
1
-
Pin
2-
(Remove the 4 screws
indicated by arrows.)
LINE ARRAY SPEAKER
TOA Corporation
IMPEDANCE
8
Ω
CONT.
PGM. INPUT
360W
To change the tap, refer to the instruction manual enclosed with the MT-S0601.
Primary side impedance
High impedance 100 V line
High impedance 70 V line
83 Ω
170 Ω
330 Ω
670 Ω
Unusable
60 W
30 W
60 W
30 W
15 W
7.5 W
15 W
The diagram below is an internal wiring when the matching transformer is installed.
Matching transformer
MT-S0601
Woofers
Screw
Neutrik NL4MP connectors
terminals
INPUT +
Passive
network
1+
1+
INPUT –
THROUGH
THROUGH
2–
1–
2–
1–
x 4
2+
2+
Tweeters
Input terminal panel
x 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
9. JOINING SPEAKERS
Joining line array speakers configures a longer linear sound source, permitting richer low-frequency sound
reproduction as well as transmission of higher sound output over a longer distance.
To join speakers, use the optional SR-EP4 Extension Plate.
[Joining procedure]
Step 1. Remove the (M5 oval-head) screws on both sides of the speaker.
The removed screws are no longer used.
Step 2. Join 2 speakers using the SR-EP4 Extension plate.
Fix the plate to the speaker using the hex head bolts supplied with the SR-EP4.
Note
Maximum number of speakers to
be jointed are 3, when using 2 sets
of SR-EP4.
Speaker
Note
The screws removed
in Step 1 are not used.
Extension plate SR-EP4
(optional)
Hexagon head bolt M5 x 20 with washer
(supplied with the SR-EP4)
Speaker
10
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ATTACHING THE PROTECTION PAD TO THE SPEAKER EDGE
When installing the speaker at head height, attach the optional SR-RP4
Protection Pad to the speaker edges.
If people should bump their heads directly against the corners or edges
WARNING
of the enclosure, injuries could result.
Remove the protective paper of the double-faced tape affixed to the SR-PP4 Protection Pad (optional) and
attach the pad to the speaker edge as shown in the figure.
Protection pad SR-PP4
Double-faced tape
Protection pad SR-PP4
11
Download from Www.Somanuals.com. All Manuals Search And Download.
11. CHANGING SINGLE-AMPLIFIER DRIVE TO BI-AMPLIFIER DRIVE SYSTEM
The single-amplifier drive system can be changed to a bi-amplifier drive system by changing the speaker's
internal wiring after removing the input terminal panel located at the back of the speaker.
[How to change]
Step 1. Remove the 4 terminal panel mounting screws to remove the input terminal panel.
Step 2. Carefully pull out the short length of wiring connected to the back of the input terminal panel.
Step 3. Unplug 2 pairs of connected connectors, and reconnect them so that connections are made between
labeled connectors and between unlabeled connectors.
Step 4. Reattach the input terminal panel to the speaker using the 4 screws.
Step 5. Affix the supplied label to the input terminal panel to change the indication.
Input terminal indication change
5
Bi-amplifier terminal label (supplied)
Bi-amplifier rating label (supplied)
3
Connector connection change
Panel mounting screw
Label
1, 4
2
Input terminal panel
12
Download from Www.Somanuals.com. All Manuals Search And Download.
12. INTERNAL WIRING DIAGRAM FOR THE BI-AMPLIFIER DRIVE SYSTEM
The diagram below is an internal wiring after the speaker's drive system is changed to a bi-amplifier system.
Woofers
Screw terminals
Neutrik NL4MP connector
LOW +
LOW –
HIGH +
HIGH –
1+
1+
2–
1–
2–
1–
x 4
2+
2+
Tweeters
Input terminal panel
x 4
• Since the Neutrik NL4MP connectors and screw terminals are internally connected in parallel, either one can
be used for connection.
Pin No. SR-S4L, SR-S4S Screw terminal indication
• The Neutrik NL4MP connector's pins are wired
as shown at right.
The connector (connection cable side) suited to
the Neutrik NL4MP is the Neutrik NL4FC.
1 +
1 –
2 +
2 –
LOW +
LOW –
HIGH +
HIGH –
LOW +
LOW –
HIGH +
HIGH –
13
Download from Www.Somanuals.com. All Manuals Search And Download.
13. DIGITAL PROCESSOR FILTERING
13.1. Single-Amplifier Drive (Factory-Setting)
Although the speaker can be operated without a digital processor, it is recommended that the speaker be
used in conjunction with a digital processor for better sound reproduction. Recommended setting parameters
are as follows.
TYPE
HPF (12 dB)
PEQ
Frequency
60 Hz
Gain
5 dB
Q
1.226
1.414
16 kHz
13.2. Bi-Amplifier Drive
Digital processing is required after the drive system has been changed to bi-amplifier operation. By inputting
an optimum signal to the woofer and tweeter using the digital processor, a high sound quality output can be
realized. Recommended setting parameters are as follows.
Filter
Channel
LOW
Gain
0 dB
Polarity
Normal
Delay
0 ms
Frequency
60 Hz
Gain
2 dB
Q
TYPE
HPF (12 dB)
PEQ
1.226
1.707
0.700
0.500
0.707
2.997
1.512
1.414
63 Hz
PEQ
1.5 kHz
4.0 kHz
4.0 kHz
4.0 kHz
6.3 kHz
16.0 kHz
-5 dB
LPF (12 dB)
HPF(12 dB)
PEQ
HIGH
-2 dB
Normal
0.125 ms
3 dB
3 dB
5 dB
PEQ
-
PEQ
14
Download from Www.Somanuals.com. All Manuals Search And Download.
14. SPECIFICATIONS
14.1. Line Array Speaker SR-S4L, SR-S4S
Model No.
SR-S4L
SR-S4S
Enclosure
Bass-reflex type
Continuous program: 600 W
8 Ω
Power Handling Capacity
Rated Impedance
Sensitivity
94 dB (1 W, 1 m)
93 dB (1 W, 1 m)
Frequency Response
Crossover Frequency
Directivity Angle
70 – 20,000 Hz (when using the optional DP-0206 Digital processor)
3,500 Hz
Horizontal: 90°
Horizontal: 90°
Vertical: 0° (within the range of
speaker height)
Vertical: 10°
Speaker Component
Input Connector
Finish
Low frequency: 10 cm cone-type x 8
High frequency: 2.5 cm balanced dome-type x 24
M5 screw terminal, distance between barriers: 12.2 mm
and Neutrik NL4MP x 2 (usable cable connector: Neutrik NL4FC)
Enclosure: MDF, white, paint
Front grille: Punched steel plate, white, acrylic paint
Dimensions
Weight
160 (w) x 895 (h) x 255 (d) mm
160 (w) x 892 (h) x 303 (d) mm
16 kg
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Bi-amplifier rating label ................................... 1
Bi-amplifier terminal label ................................ 1
• Optional products
Matching transformer: MT-S0601
Extension plate:
Flying bracket:
Wall tilt bracket:
SR-EP4
SR-FB4
SR-TB4
Wall mounting bracket: SR-WB4 (Applicable to the SR-S4L only)
Floor stand:
SR-FS4 (Applicable to the SR-S4L only)
Stand adapter:
Protection pad:
Digital processor:
SR-SA4
SR-PP4
DP-0206
15
Download from Www.Somanuals.com. All Manuals Search And Download.
14.2. Extension Plate SR-EP4 (optional)
The SR-EP4 is used to join multiple SR-S4L or SR-S4S speakers. One complete set consists of 2 brackets.
Number of Speaker to be Jointed Max. 3 (when using 2 sets of SR-EP4)
Finish
Steel plate, white, paint
Dimensions
Weight
140 (w) x 220 (h) x 2.3 (t) mm
1.1 kg (including accessories)
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Hexagon head bolt M5 x 20 with washer .......... 16
14.3. Protection Pad SR-PP4 (optional)
When the SR-S4L or SR-S4S speaker is installed so that its bottom edge is located at head height, people
could bump their heads directly against the speaker and suffer injuries. Affixing this protection pad to the
speaker's bottom surface helps reduce the impact and chance of injury.
Finish
Synthetic rubber, black
168 (w) x 59 (d) x 8 (t) mm
40 g
Dimensions
Weight
Note: The design and specifications are subject to change without notice for improvement.
Printed in Japan
133-05-385-40
Download from Www.Somanuals.com. All Manuals Search And Download.
|