MAS3
ZEKTOR
TM
Multi-channel Audio Switch
Owner’s Manual
Rev: 2
03/12/04
Download from Www.Somanuals.com. All Manuals Search And Download.
A MAS3 Overview
Operating the MAS3 is straight forward and simply a matter of plugging the MAS3’s power supply
into an available A.C. outlet, and then plugging the MAS3’s power supply into the back of the MAS3.
To operate the MAS3 manually, press the power switch, located on the very left of the MAS3 to cy-
cle power.
Press any one of the three channel switches to switch the MAS3 to the selected channel.
If the MAS3’s power is turned off, selecting any one of the three inputs will cause the MAS3 to power
on and switch to the selected channel.
POWER TOGGLE
CHANNEL 1
CHANNEL 2
CHANNEL 3
• POWER TOGGLE. Pressing this button will cycle power from on to off, and off to on.
• CHANNEL 1. Pressing this button will select channel 1 of the MAS3’s inputs, if power is off when
this button is pressed, then the MAS3 will power on, and select channel 1.
• CHANNEL 2. Pressing this button will select channel 2 of the MAS3’s inputs, if power is off when
this button is pressed, then the MAS3 will power on, and select channel 2.
• CHANNEL 3. Pressing this button will select channel 3 of the MAS3’s inputs, if power is off when
this button is pressed, then the MAS3 will power on, and select channel 3.
3
Using the MAS3 with a Remote Control
Remote operations of the MAS3 are accomplished through the use of just about any remote control.
A remote control is not supplied with the MAS3, yet the versatile programming modes of the MAS3
allows the MAS3 to work with virtually any remote control. The next section "Programming your Re-
is programmed the following describes the pre-programmed functions of the MAS3.
There are 9 separate remote controlled commands understood by the MAS3. They are:
• POWERTOGGLE.The MAS3 can be toggled from standby to power
on, and back to standby using a single button of the remote.
• SELECTIN1. Select input 1. If the MAS3 is in standby mode, it will
power on and then select input 1.
POWER
CBL /
SAT
TV
VCR
DVD RCVR
• SELECTIN2. Select input 2. If the MAS3 is in standby mode, it will
power on and then select input 2.
• SELECTIN3. Select input 3. If the MAS3 is in standby mode, it will
power on and then select input 3.
• POWEROFF. The MAS3 can be set to standby mode by pressing a
single button of the remote. Once the MAS3 is in standby mode,
further presses of the POWEROFF button will be ignored. This com-
mand is useful when using the “macro” feature of some program-
mable remote controls, and is used when it is unknown whether the
MAS3 is already in standby mode or not.
1
2
5
8
0
3
6
4
7
9
PIP
ENT
• POWERON. The MAS3 can be powered on from standby by pressing
a single button of the remote. Once the MAS3 is power on, further
presses of the POWERON button will be ignored. This command is
useful when using remote controls that allow “macro” programming,
where it is unknown whether the MAS3 is already power on or not.
• SETDIMMODE. Toggles through three different bright/dim display
modes. They are: Bright all the time. Dim all the time. Bright for 4 sec-
onds after any keypress, and then automatically dim.
CH
VOL
• SELECT+. Select the next higher input. If input 3 is currently selected,
+
+
then this command will cause input 1 to be selected.
_ _
• SELECT-. Select the next lower input. If input 1 is currently selected,
then this command will cause input 3 to be selected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming your Remote Control
Setting up your Universal Remote Control
For remote control operations, the MAS3 requires either a Universal Remote control to be pro-
grammed as one of eight pre-programmed devices, or alternatively, the MAS3 can be taught to use
most existing remote controls.
The simplest way begin using the MAS3, is to program your Universal Remote control to act like a
Symphonic TV. Once this is done you will be able to immediately start using your MAS3.
Check your remote’s user manual for instructions on programming your remote control.
The following table shows the Symphonic TV codes for a few different brands of Universal Remote
Controllers:
Make
Device
Code
Sony
One For All
Sanyo
TV
TV
TV
TV
TV
023
0476
303
GE / RCA
X10
046
062
Zenith / Phillips /
Magnavox
TV
552
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Different Remote Codes
Using Alternate Component Keys on your Remote
The MAS3 will also respond to alternate component key codes. Allowing you to use an unused TV,
VCR, RCVR or one of the added AUX positions many remotes include.
Setting up the MAS3 to respond to alternate component codes is a two step process. You must first
program your universal remote control to behave as one of the components in the following table.
You must then teach the MAS3 to respond to the same set of alternate component codes.
Programming your remote to different components
The MAS3 will respond to eight different pre-programmed component codes, they are: Symphonic
TV, Hatachi Satellite, Sony TV, Yamaha VCR, Go Video VCR, Awia DVD, Nakamichi Receiver and
a Jerrold Cable Box. The following table shows the different component buttons and codes used to
program a few different universal remotes.
OneFor
Make
Device Sony
Sanyo RCA Zenith X10
All
Symphonic
Sony
TV
TV
023
001
N/A
040
N/A
015
086
001
0171
0000
0819
0038
0432
0641
N/A
104
110
N/A
238
248
N/A
N/A
303
189
002
084
009
138
350
N/A
046
520
708
N/A
025
139
N/A
N/A
552
202
015
N/A
022
013
N/A
N/A
062
Hatachi
Yamaha
Go Video
Awia
SAT
VCR
VCR
DVD
RCVR
CBL
Nakamichi
Jerrold
0476
If your remote control’s model matches one of the above, read your remote’s user manual for in-
structions on programming your remote control, then use the above device and manufacturer codes
to setup your remote.
If your remote is not included above list, or the manufacturer code given does not work, then you
will have to follow your remote controls instructions for programming one of the above components
and search for a proper match. See the next section. Or teach the MAS3 a new set of codes, See:
Teaching the MAS3 a new component code
After your remote control has been programmed to act like one of the 8 built in code-sets, teaching
the MAS3 to use the new code set is simple.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1
1 Place the MAS3 in standby mode. This is the factory default mode
on power up, and if it has not been changed, you can unplug the
MAS3 and plug it back in and it will power up in standby mode (at
this point only the power indicator light is lit and glowing RED). If
the MAS3 does not power up in standby mode, follow the steps
ZEKTOR
1
2
3
STEP 2
2 On your remote control press the buttons in the following
sequence, after each button press verify that the remote IR
indicator flashes. (If you make a mistake, you can start over by
pressing POWER twice.):
ZEKTOR
1
2
3
• POWER
• CHANNEL +
• POWER
• CHANNEL -
STEP 3
3 The MAS3 will power up indicating the new component codes have
ZEKTOR
1
2
3
been accepted.
Searching for a component code in your remote
Assuming you do not have a remote listed in this user manual you will have to follow your remote
controls programming sequences to find a compatible component that the MAS3 understands, or
for individual commands.
To search for compatible component codes you must place the MAS3 in standby mode and try
manufacturer codes in your remote control until one of them causes the MAS3’s IR indicator LED
to flash.
STEP 1
1 Place the MAS3 in standby mode. This is the factory default mode
on power up, and if it has not been changed, you can unplug the
MAS3 and plug it back in and it will power up in standby mode (at
this point only the power indicator light is lit and glowing RED). If
the MAS3 does not power up in standby mode, follow the steps
ZEKTOR
1
2
3
STEP 2
2 Try different manufacturer codes until one of them causes the IR
indicator light on the MAS3 to blink when pressing the
use the new component code.
ZEKTOR
1
2
3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Learning New Remote Codes
Teaching the MAS3 to use new remote control keys
If your remote does not have one of the pre-programmed component codes, or you simply want to
re-map the MAS3 functions to other keys on your remote, the MAS3 can be taught to use new keys.
To teach the MAS3 to respond to new keys, you need to have the remote control(s) you want to use
ready, and setup in the manner you want it to be used.
STEP 1
1 Place the MAS3 in standby mode. This is the factory default mode
on power up, and if it has not been changed, you can unplug the
mlugin se16.34.114 TD0.003 T1c0.0006 lf(m)4willwerin stain nd
8
STEP 4
4 The Power indicator blinks slowly, and input 2 is selected.
ZEKTOR
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3
3
Press the key on your remote that you want to use as the new key
for SELECTIN2.
1 BLINK
STEP 5
5 The Power indicator blinks slowly, and input 3 is selected.
ZEKTOR
Press the key on your remote that you want to use as the new key
for SELECTIN3.
1 BLINK
STEP 6
6 After a pause, the Power indicator blinks 2 times, and repeats.
ZEKTOR
Press the key on your remote that you want to use as the new key
for POWERTOGGLE.
2 BLINKS
STEP 7
7 After a pause, the Power indicator blinks 3 times, and repeats.
ZEKTOR
Press the key on your remote that you want to use as the new key
for SELECTIN-.
3 BLINKS
STEP 8
8 After a pause, the Power indicator blinks 4 times, and repeats.
ZEKTOR
Press the key on your remote that you want to use as the new key
for SELECTIN+.
4 BLINKS
STEP 9
9 After a pause, the Power indicator blinks 5 times, and repeats.
ZEKTOR
Press the key on your remote that you want to use as the new key
for SETDIMMODE.
5 BLINKS
STEP 10
10 After a pause, the Power indicator blinks 6 times, and repeats.
ZEKTOR
Press the key on your remote that you want to use as the new key
for POWERON.
6 BLINKS
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11
11 After a pause, the Power indicator blinks 7 times, and repeats.
ZEKTOR
1
2
3
Press the key on your remote that you want to use as the new key
for POWEROFF.
7 BLINKS
STEP 12
12 The MAS3 will return to the standby mode indicating a return to
normal operations. The newly programmed codes will now operate
your MAS3.
ZEKTOR
1
2
3
Remote Control Learning Caveats
Some component’s control codes will work better than others. We’ve designed the MAS3 to work
with a great majority of codes, however a few brands use non-standard ways of transmitting their
component’s codes that may not be compatible with the MAS3. In these somewhat rare circum-
stances you will have to program your remote control to a different manufacturer’s code, and/or use
different buttons on your remote.
When programming the MAS3, if the IR indicator light blinks, and the MAS3 moves on to the next
step, then the remote controller’s key code has been accepted. If the IR indicator does not blink, it
indicates the MAS3 does not understand that particular manufactures code and you will have to
choose another.
In some cases the remote key code will be accepted, however the range will be limited. If the range
of a programmed key is unacceptable, you will have to choose a different manufacturer and try
again.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Bright / Dim / Auto-dimming Modes
Setting the Display intensity modes of the MAS3
The front panel display of the MAS3 can be set to Bright, Dim or an Auto-dimming mode where the
display brightens for 4 seconds after any function is selected and then auto-dims.
Setting the mode is simply a matter of toggling between the three modes:
• Bright Mode. When pressing the SETDIMMODE key to toggle to this state, the display will turn
bright and remain that way.
• Dim Mode. When pressing the SETDIMMODE key to toggle to the Dim mode, the display will go
dim and remain that way.
• Auto-dimming Mode. When pressing the SETDIMMODE key to toggle to the Auto-dimming
mode, the display will turn bright, then flash to dim, then flash back to bright, indicating the
Auto-dimming mode has been selected. After 4 seconds of no activity, the display will smoothly
dim to the dim setting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Power On Defaults
The MAS3 power on default mode
When toggling between Standby mode and PowerOn the MAS3 will remember all it’s current set-
tings. After completely powering down the MAS3 (by unplugging the AC wall adapter), upon restor-
ing power (by plugging the AC wall adapter back in), it will power up in a user settable default mode.
This is useful in situations where the MAS3 is externally switched by a power strip.
The factory default settings for initial power on are:
• Initial power up in Standby mode.
• Input 1 selected when powered on.
• Auto-dimming mode selected.
Changing the MAS3 power on defaults
Teaching the MAS3 new power on default settings consists of placing the MAS3 in the preferred
initial power on mode, and pressing and releasing the SETUP button on the back panel of the
MAS3.
STEP 1
1 Select an initial power on input.
ZEKTOR
1
1
1
2
2
2
3
3
3
Using the SELECTIN1 - SELECTIN3 keys, or the SELECT+ or SELECT-
keys, choose the desired power on default input.
STEP 2
2 Select the initial Bright / Dim / Auto-dimming mode.
ZEKTOR
Using the SETDIMMODE key, choose the desired power on default
Bright / Dim / Auto-dimming mode.
STEP 3
3 Select the initial power mode, Standby or Powered on.
ZEKTOR
Using the POWERTOGGLE, POWERON or POWEROFF keys, choose
the initial power on mode.
STEP 4
4 Press and release the SETUP button located on the back panel of
the MAS3. The power Indicator light on the MAS3 will blink once to
indicate the new power on setting have been saved.
ZEKTOR
1
2
3
or
The previous picture shows the default power up mode, as being
set to the standby mode. It may also be set to the power on mode,
by pressing and releasing the setup key while power is on, as
shown here.
ZEKTOR
1
2
3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Restoring the MAS3 to Factory Defaults
Restoring the MAS3 to the factory defaults
There are many ways to program the MAS3’s remote capabilities. Most learning modes require the
MAS3 to be in standby mode before learning can begin. If the remote used to control the MAS3
were to be lost, and the MAS3 were programmed to power on during initial power up (as described
cept new remote control codes. Therefore a means of resetting the MAS3 to its factory on defaults
has been included.
Resetting the MAS3 to the factory defaults is done by removing power to the MAS3. The AC wall
adapter must be unplugged, so that the MAS3 is completely without power. The SETUP key is then
pressed and held while power is restored to the MAS3, after about three seconds the power indica-
tor will flash three times indicating the MAS3 has been reset to factory defaults.
STEP 1
1 Remove all power from the MAS3, this can be done by unplugging
the AC wall adapter from the back of the MAS3, or unplugging the
AC adapter from the wall, or by using a switched power strip.
Nothing should be lit on the MAS3.
ZEKTOR
1
1
1
2
2
2
3
3
3
STEP 2
2 Using a pen or pencil, press AND HOLD the SETUP button on the
back panel of the MAS3. While continuing to HOLD the SETUP
key, reapply power to the MAS3. When power is applied, the power
indicator light will light up indicating standby mode.
ZEKTOR
STEP 3
3 Continue to HOLD the SETUP key and after about three seconds
the power indicator will blink GREEN three times indicating the
MAS3 has been reset to its factory defaults.
ZEKTOR
The MAS3 factory defaults, are:
• Control codes used are the Symphonic TV codes.
• Default power up mode is standby.
• Default selected input when powered on is input 1.
• Default brightness mode is Auto-dimming.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Application
SACD player
L
L
L
SUB
L
L 1
L 3
SUB
SUB
SUB
L
L
OUT
2
DC
input
CENTER
R
R
CENTER
R
R
CENTER
R
R
R
R
CENTER
SACD Player # 2
DVD-A Player
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To
6
channel
Warranty Information
Warranty Policy
ZEKTOR, LLC warrants this product against defects in material and workmanship under normal use
and service for one year from the original date of purchase. ZEKTOR, at its option, shall repair or
replace the defective unit covered by this warranty.
In order to keep this warranty in effect, the product must have been handled and used as prescribed
in the instructions accompanying this warranty. This warranty does not cover any damage due to
accident, misuse, abuse, or negligence. This warranty is valid only if the product is used as speci-
fied in the product documentation.
Repair or replacement, as provided under this warranty, is your exclusive remedy. ZEKTOR shall
not be liable for any incidental or consequential damages. Implied warranties of merchantability and
fitness for a particular purpose on this product are limited in duration to the duration of this warranty.
Some states/countries do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you. Some states/countries do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights that vary from state to
state and country to country.
Return & Exchange
Shipment of product is as advertised by product. Upon receipt of merchandise inspect product care-
fully, should you find that the product does not meet your expectations, or satisfaction, contact us
at once and tell us your concerns, so we may make every effort to satisfy your purchase.
Instructions for returning items
Please retain the dated sales receipt as evidence of the date of purchase. You will need it for any
warranty service. If you bought the product through a dealer, installer, or reseller, you will need to
return the product to the point of sale.
E-Mail us, or call us, using the information listed under “Customer Service Contact Information” on
the following page, for a Return to Manufacturer Authorization (RMA) number. Describe briefly the
reasons for your requested return. You must receive an RMA # before you return any goods to us,
the RMA # must appear on your return packing label or on the outside of the box, Merchandise with-
out a RMA # will be refused, and no credit will be issued. RMA's are valid for ten (10) days from
date of issuance. All returned merchandise must be shipped in the original packaging. If it is not in
the original packaging, ZEKTOR will not be held liable for damage during shipment. Shipments of
returns must be prepaid, and we will not accept COD returns.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Service Contact Information:
ZEKTOR, LLC
12675 Danielson Court
Suite 401
Poway, CA 92064
Email: [email protected]
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|