swisherinc.com
OWNER’S
MANUAL
MODEL NO.
RTB115441
RTB134412V
RTB14544
44” ROUGH CUT
TRAIL CUTTER
Assembly
Operation
Service and Adjustment
Repair Parts
Rev. 05-033
1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093
PHONE (660) 747-8183 FAX (660) 747-8650
Made In The
Manufacturing quality lawn care equipment since 1945
USA
Download from Www.Somanuals.com. All Manuals Search And Download.
10292
Thank you for choosing Swisher’s 44 ‘’ Trailcutter. Before operating
your cutter, please read, understand and follow all of the safety precautions
and other instructions explained in this manual . As with all power
equipment, lawn mowers,and cutters can be potentially dangerous if
improperly used.
SAFETY PRECAUTIONS
This Safety Alert Symbol indicates important messages in this
manual. When you see this symbol, carefully read the message that
follows and be alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands and feet, and
throw objects. Failure to observe the following safety instructions could result in
serious injury or death.
•
•
Read the manual. Learn to operate this machine safely.
Always disconnect the spark plug wire and place the wire where it cannot contact the
spark plug, to prevent accidental starting the engine when setting up, transporting,
adjusting or making repairs.
•
•
Keep all shields and guards in place.
Understand the speed, steering and stability of this machine. Know the positions and
operations of all controls before you operate this machine. Check all of the controls in
a safe area before starting to work with this machine.
•
•
•
Allow only responsible adults who are familiar with these instructions to operate this
machine. Never allow children to operate this machine.
Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and
thrown by the blade.
Be sure the area is clear of other people before mowing. Be aware of the cutters
discharge direction and do not point at anyone. Stop the machine if anyone enters the
cutting area. Children are often attracted to the machine and the mowing activity.
Never assume that children will remain where you last saw them. Keep children
under the watchful care of another responsible adult.
•
•
•
No riders!
Do not put hands or feet near or under rotating parts.
Do not mow in reverse. Always look down and behind before and during backing.
Download from Www.Somanuals.co3m. All Manuals Search And Download.
•
Turn off the blades when not cutting. Before leaving the machine, turn off the blades
and stop the engine.
•
•
Watch for traffic when operating near or crossing roadways.
Do not operate the cutter if it has been dropped or damaged in any manner or if the
mower vibrates excessively. Excessive vibration is an indication of damage.
Repair cutter as necessary.
•
Dress properly. Do not operate the cutter when barefoot or wearing open sandals.
Wear only solid shoes with good traction when cutting.
•
•
•
•
•
Never allow operation by untrained persons.
Do not operate the machine while under the influence of alcohol or drugs.
Do not operate on slopes greater than 15 degrees.
Never tamper with safety devices. Check their proper operation regularly.
Stop and inspect the equipment if you strike an object. Repair, if necessary, before
restarting. Never make adjustments or repairs with the engine running.
Cutter blades are sharp and can cut. Wrap the blades or wear gloves, and use extra
caution when servicing them. Do not operate at too fast a rate.
Return lever to its vertical position to disengage blades.
The braking system is applied when the blades become disengaged. It is designed to
bring the blades to a quick stop (approximately 7 seconds). Each Trailcutter brake
system has been tested and calibrated. For safety, the consumer should not alter the
braking system.
•
•
•
ASSEMBLY
•
•
Disengage spark plug wire and place where it cannot make a connection.
Refer to Figure 2 p.11. Attach hitch assembly parts to front of mower . Insert 3/8-16 X 2 ½ through
plate and attach 3/8-16 nut to the bottom. Tighten nut tight until tube is clamped then back off ½ turn to
allow tube to pivot.
• The L hitch can be adjusted up or down to level the deck from front to back
•
Check engine oil. All engines are filled with oil at the factory. Verify oil level and
add if necessary before starting engine. (See Engine Owner’s Manual)
Verify fuel level and add if necessary before starting engine.
Check the battery (if so equipped). If battery is put into service after the “month & year” of the
date on the battery, then it may need to be charged with a 12 volt battery charger for a minimum
of 1 hour, but no more than 2 hours at a rate of 6 to 10 amps.
•
•
•
Attach battery cable(s) to battery. ( if so equipped ) Red wire to positive (FIRST) and black wire to
negative (SECOND).
•
•
Reconnect spark plug wire.
(Refer to Owner’s Manual p. 5) For proper operating procedures.
Download from Www.Somanuals.co4m. All Manuals Search And Download.
OPERATING YOUR TRAILCUTTER
The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye
damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any
cutting machine and while operating such a machine.
The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is
recommended.
CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children.
Children are often attracted to the machine and the mowing activity. Never assume that children will
remain where you last saw them.
INTENDED USE
The 44” Rugged Cut Trailcutter is designed to clear dense areas of grass and cut saplings up to 1-
1/2 inch thick on meadows and small estates. It is not intended to create a finish cut on
lawns.Your Trailcutter should be towed behind an ATV, golf cart, lawn tractor or other approved
vehicle. It is not recommended for speeds exceeding 5 MPH.
ATTACHING TRAILCUTTER TO TOW VEHICLE
•
•
Back vehicle up to desired towing position.
Offset the Trail Cutter to the side opposite the tow vehicle discharge (if any).
This prevents the tow vehicle from throwing grass into Trailcutter engine.
Bolt swivel hitch (H10) to tow vehicle receiver. If tow vehicle has a ball
hitch, the ball must be removed before swivel hitch can be fastened.
Attach tow hitch and the “L” hitch (10388TK & H1) to the swivel hitch.
The hitch pin (H11) should go completely through both the swivel and “L”
hitches and clipped to prevent accidental separation. Check that all hardware
is secure at both the tow vehicle and the Trailcutter.
•
•
TRANSPORTING CUTTER
•
•
•
Stop Trailcutter.
Place Trailcutter deck in its highest position.
When transporting unattached from tow vehicle, remove spark plug wire and
place it where it cannot contact the spark plug.
STOPPING THE ENGINE
•Make sure the tow vehicle parking brake is set
•Disengage cutting Blades
•Reduce engine to idle speed and allow engine to run momentarily for cooling
•Turn the key to the off position
Download from Www.Somanuals.co5m. All Manuals Search And Download.
ENGAGING BLADES
Note: Do not attempt to start the unit with the T-handle console in the ‘’ ENGAGED ’’ position.
• Engage blades by pulling down the T-handle lever into the horizontal position.
• Return lever to the vertical position to disengage blades. See detail on page 14 figure – 8
• The braking system is applied when the blades become disengaged. It is designed to bring the blades
to a quick stop ( approximately 7 seconds. ) Each TrailCutter brake system has been tested
for safety , the consumer should not alter any part of the brake system.
BREAKING IN YOUR CUTTER
•
•
•
Set the vehicle parking brake and chock the wheels to prevent accidental rolling.
While the engine is running, slowly, engage blade control.
In a safe environment, (i.e. no children or pets) allow blades to rotate and engine to
idle for 5 minutes, breaking in the belt for a longer life.
Stop cutter.
•
STARTING THE ENGINE
See engine manufacturer’s recommendations for the type and amount of oil and fuel used.
•
Make sure the tow vehicle parking brake is set, mower is level, and blades are
disengaged. Engine must be level to accurately check and fill oil. Do not overfill.
Check spark plug wire, oil, and fuel.
Check all electrical connections for build-up of debris.
Set engine idle to “CHOKE” position.
Turn key to the “RUN” position.
Pull rope with a single fluid motion.
(12V models only) Turn key to the “RUN” position, then to the “START” position.
Set engine idle at maximum RPM for best performance.
Allow engine to run a few moments before engaging blades.
•
•
•
•
•
•
•
•
CAUTION: SHUT OFF THE CUTTER ENGINE AND REMOVE SPARK
PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY
ADJUSTMENTS TO THE CUTTER.
FRONT TO BACK ADJUSTMENT
For best cutting results, the cutter deck should be parallel to the ground. To check parallel
adjustment, measure the distance from the bottom edge of the deck in both the front and rear of
the deck. This adjustment is best done while the tow vehicle and Trailcutter are connected.
•
•
•
Remove bolt and nut from the “L” hitch (10388TK ).
Raise or lower hitch section to obtain proper front to back adjustment.
Connect bolt and nut in “L” hitch securely, Then rotate nut counter- clockwise ½
turn,“L” hitch should pivot freely.Bolt must go completely through nut ( but do not over
tighten). See figure – 2, page 11
Download from Www.Somanuals.co6m. All Manuals Search And Download.
CUTTER HEIGHT ADJUSTMENT
•
•
There is approximately 4 inches of height adjustment.
Rotate height adjust crank handle in a clockwise direction to lower the mower deck.
counter-clockwise direction to lift the mower deck.
Dense areas of material should be cut twice.
•
•
Push handle down to lock height position.
TOW HITCH OFFSET
•
When offsetting the cutter do so to the side opposite the discharge of the tow
vehicle.
•
Swisher recommends if the tow vehicle is equipped with a mid-mount mower to
overlap the cut approximately 6”. This may vary depending on mowing terrain,
obstacles, and/or tow vehicle. Always keep safety the first priority.
Always keep the tow vehicle cutter raised higher than the Trailcutter
Loosen and remove two back side bolts ( NB164 ) of hitch bar ( 10339TK ) position
hitch bar to desired setting see figure – 2,3 page 11 replace bolts making sure to retighten.
•
•
STARTING TO CUT
•
•
•
•
•
Adjust the cutting height.
Double check vehicle to cutter attachment.
Start mower engine and set throttle to “FAST” for best cutting performance.
Slowly engage T-handle lever.see figure-8 page 14
Carefully mount tow vehicle and start mowing at a slow travel speed.
STOPPING THE CUTTING SESSION
•
•
•
Bring tow vehicle to a complete stop, set the parking brake and disengage blades.
Turn key switch to the “OFF” position.
Always remember to remove keys to avoid irresponsible usage.
SUGGESTED CUTTING PRACTICES
•
Operate cutter engine at full throttle to assure the best cutting performance and
maximum material discharge.
•
•
Allow wet grass to dry. Wet grass will clump and collect under the mowing deck.
Cutter should be started with tow vehicle in low gear and increased only as safe
mowing conditions permit. Cutting speed should not exceed 5 MPH.
Cutting conditions and the types of grass will vary from place to place. You may
find when cutting dense areas that the pressure of the wheel tracks may cause the
grass to be pushed down and not effectively mowed. If this happens you may want
to mow the area twice. Once with the cutter raised and the second cutting at the
desired height. The second cutting should be at a right angle from the previous for
best results.
•
•
•
Reducing the travel speed will help cut dense growth. This allows the blades the
time necessary to make its initial cut, and regain momentum to continue cutting and
discharging debris properly. The engine may stall if you are mowing too fast!
Do not attempt to cut areas that the tow vehicle cannot maneuver through and/or
slopes that you do not feel comfortable riding.
Download from Www.Somanuals.co7m. All Manuals Search And Download.
CUTTER MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty on this cutter does not cover items that have been subjected to operator
abuse or negligence. To receive full value from the warranty, operator must maintain
unit as instructed in this manual.
Some adjustments will need to be made periodically to maintain your unit properly.
BEFORE EACH SEASON
A new spark plug and clean air filter assure proper air fuel mixture and help your engine
run better and last longer.
•
•
•
Replace the spark plug.
Clean or replace the air filter.
Check blades and belts for wear.
BEFORE EACH USE
•
•
•
•
•
Check engine oil level. (Do this twice to ensure an accurate reading.)
Check condition of air filter and clean or replace if necessary.
Check blade operation.
Check for loose fasteners.
Lubricate threads of adjustment rod P/N 4006 figure –4 page 12
DAILY MAINTENANCE
Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure.
Keep blades sharp. Observe all safety precautions.
BLADE CARE AND SERVICE
For best results cutter blades must be kept sharp. The blades can be sharpened with a
few strokes of a file or grinding wheel. Do Not attempt to sharpen while on the cutter.
Important: Replace blades that have been damaged or deeply nicked.
Important: Check blade and spindle hardware on a regular basis to make sure
nuts are tight.
CAUTION: DO NOT HANDLE CUTTER BLADES WITH BARE HANDS.
CARELESS OR IMPROPER HANDLING MAY RESULT IN SERIOUS
INJURY.
Download from Www.Somanuals.co8m. All Manuals Search And Download.
GENERAL TROUBLESHOOTING
The unit is not cutting level.
•
Level deck. Check air pressure of all tires; make sure they are equal. See
tires for maximum inflation.
• Without the engine running, make certain blades are installed identically.
The engine will not start.
•
Disengage blades, turn key switch to the “OFF” position, check battery and
all other electrical connections and inspect spark plug and wire.
Contact engine manufacturer or qualified mechanic.
•
Engine runs poorly.
•
•
•
•
See engine manual.
Check the throttle adjuster.
Replace fuel, clean fuel filter and fuel line.
Check spark plug and gap.
Cutter bounces excessively while towing.
•
•
Lower tire pressure.
Tow at a lower speed.
IF PROBLEMS PERSIST HAVE A QUALIFIED MECHANIC SERVICE
THE CUTTER. NEVER ATTEMPT TO MAKE AN ADJUSTMENT THAT
YOU ARE NOT SURE IS CORRECT. DOING SO CAN CAUSE OTHER
PROBLEMS.
Download from Www.Somanuals.co9m. All Manuals Search And Download.
SAFETY AND OPERATIONAL DECALS
Replace decal immediately if damaged. Order by part number from
Swisher Mower and Machine Co. Inc. 1-800-222-8183,8-5 CT M-F
OD39-SWISHER FLAG DECAL
OD82-44 RUGGED CUT DECAL
OD33-5MPH DECAL
OD29-DANGER DECAL
OD36-Deflector Decal
OD55-DANGER DECAL
OD10-ENGAGE DECAL
OD45-WARNING DECAL
OD99-OFF/RUN DECAL
OD28-OFF/RUN/START DECAL
Download from Www.Somanuals.com. All Manuals Search And Download.
10
FRONT SKIRT ASSEMBLY
5
FIGURE 1
2
Item #
Description
5/16-18 X 1 HCC GR5 ZP
Metal Strap For Rubber Flap
Rubber Flapper
Part #
NB501
4853TC
10384
NB181
10357TC
1
2
3
4
5
5/16-18 Nylock Nut
Deck Weldment
1
4
3
11
15
2
14
16
HITCH BAR ASSEMBLY
8
1
FIGURE 2
4
9
6
13
7
12
10
3
5
Item #
1
Description
Hitch Tube
3/8'' -16 x 3'' GR.5 BOLT
L-Hitch
Part #
4583TC
NB221
H1TK
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
5/8''-11 X 1-1/2'' Bolt
5/8''-11 Nylock Nut
3/8''-16 Nylock Nut
5/16-18 X 2 1/2 HCC GR5 ZP
5/16-18 Nyloc Nut
Safety Hitch Pin
Swivel Hitch
Lift Bar Weldment
3/8-16 X 1 1/4 Grade 5 Hex Bolt
3/8-16 Lock Nut
NB145Z
NB561
NB182
NB138
NB181
H11
H10TK
10369TK
NB618
NB182
10063
Cap
3/8 Lock Pin
Fan Hitch
NB520
4582TC
When ordering replacement parts
* = USE PAINT CODE: TC=TEX.RED,S=SILVER,TK=TEX.BLACK
Download from Www.Somanuals.com. All Manuals Search And Download.
11
1
FIGURE 4
4
Item #
Description
Part #
NB596
NB181
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
5/16-18 x 3/4 Serr Flg. Bolt
5/16-18 x Nylock Nut
Wheel, Tire, Bearing
Back Cover
1
4834
6
10366TK
10367TK
10343TK
10356TK
10355TK
10342TK
10368TC
10353TC
4006
Front Cover
Motor Base
2
5
9
Axle Bar Weldment Right
Axle Bar Weldment Left
Front Tube Weldment
Deck Front
Deck Top Weldment
Height Adjust Rod
Pivot Block
2
19
1
17
20
13
11
14
12
4007TK
NB588
18
14
20
15
1/2''-13 X 1 1/2'' HTC GR2 ZP
15 3/4'' ID X 1 1/4'' OD 18 GA Washer NB179
1
25
17
18
19
20
21
22
23
24
25
26
27
1/2''-13 Nylock Nut
1/2'' NR Mach Bushing 14 GA
SPACER
NB281
NB177
10290
NB149
NB126
H7K
ES214
NB276
NB195
10548
NB179
1
8
21
18
3
20
10
2
Washer
1/8'' x 1'' Cotter Pin
Plastic Knob
17
24
Crank Rod
Pal Nut
13/16'' X 1 1/4'' X 1/8'' Washer
5/16-18 x 1'' Serr. Flng.Bolt
3/4'' ID x 1-1/4'' OD Washer
22
23
BLADE DRIVER ASSEMBLY
FIGURE 5
16
8
Item #
Description
Stump Jumper Weldment
3/4 '' Washer ZP
Part #
4859TK
NB179
10358
NB611
NB609
6
1
2
3
4
14
Blade
13
3/4''-10 X 2 1/2 ''GR8 Bolt
3/4-10 Nyloc Nut
5
12
18
6
7
1"ID X 2"OD X 14GA Bellville Washer NB738
1'' X 1 1/2'' 10GA Washer Hardened PLN NB614HT
10
11
8
9
Blade Bearing
Tube Spacer
Blade Driver
4845
4049
9
10
11
12
13
14
15
16
17
18
4858TK
NB509
NB281
BB105SL
4846
NB601
NB612
4872
1/2''-13 X 2'' HCC GR5 ZP
1/2''-13 Nylock Nut
Spacer
Blade Pulley- 10.3125"
1''-8 X 7 1/2" GR8 ZP
1''-8 Nylock Nut ZP
Blade Driver Complete
1/2 Flat washer
8
5
7
1
3
6
2
NB555
4
15
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SILVER,TK=TEX.BLACK
Download from Www.Somanuals.1co2m. All Manuals Search And Download.
1
NOT ACTUAL
ENGINE USED
(REF. ONLY)
ENGINE PULLEY ASSEMBLY
FIGURE 6
1
2
Engine B&S
5/16-18 Serrated Flange Nut
5/16''-18 X 1 1/4'' Serrated Flange Bolt
5/16'' USS Flat Washer ZP
RT44 Belt Guide
N/A
NB170
NB253
NB556
4867
3
4
5
6
7
8
9
Spacer For Engine Pulley
5/16''-18 X 2 1/4 ''Flang Serr. GR5 ZP
Engine Pulley- 4.25"OD,1 1/4'' ID
1/4'' X 1'' Key Stock
BB105S
NB622
BB105
9031
3
14
10
11
12
13
14
15
16
Spacer Lower For Engine Pulley
Washer
Washer Belleville Engine Pulley
7/16''-20 X 1 HCF GR5 ZP
Oil Drain Valve
BB105SL
TR150W
699
NB452N
AS122
AS123
NB181
7
9
6
8
Oil Drain Cap
5/16-18 Nyloc Nut
10
15
11
2
12
13
4
5
16
BELT ENGAGE CONFIGURATION
FIGURE 7
29
Item #
1
2
Description
1/2''-13 X 2 1/2'' HCC GR5 ZP
Idler Arm
Part #
NB510
6681TK
NB121
NB180
NB250
9023mod
4898TK
NB102
NB274
NB519
NB181
B99S
NB196
NB501
NB182
699
4893
NB220
9040
28
3
4
1/2''-13 2-Way Jam Lock Nut
1/4''-20 Nylok Nut
1
20
5
6
7
1/4''-20 X 3/4'' GR5 ZP
Clutch Cable Clevis
Belt Engage Arm
27
10
9
8
9
1/4''-20 X 1'' HCC GR5 ZP
1/4'' SAE Washer
2
10
11
12
13
14
15
16
17
20
21
22
23
24
25
26
27
28
29
5/64'' X 3/4''Cotter Pin
5/16''-18 Nyloc Nut
26
21
Spacer
3
3/8'' Hardened Washer
5/16''-18 X 1'' HCC GR5 ZP
3/8-16 Nyloc Nut
17
4
25
5
Washer Belleville
Brake Arm Assembly
1/2'' X 1-9/16'' Shoulder Bolt
Torsion Brake Spring
Brake Rod
13
24
23
22
16
4891TK
NB139
682S
NB619
NB212
B527
1/4''-20 HX Nut ZP
Clutch Rod Spring
3/8''-16 X 2 1/2'' HTC GR5 ZP
3/8''-16 HNC GR2 ZP
Idler Pulley OD-3.25", ID-3/8"
3/8'' SAE Washer
6
4
15
7
14
13
12
NB272
NB182
9
8
3/8''-16 Nyloc Nut
10
11
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SILVER,TK=TEX.BLACK
Download from Www.Somanuals.com. All Manuals Search And Download.
13
CONSOLE ASSEMBLY
FIGURE 8
Item #
Description
T Handle for Console
1/4-20 Nylok Nut
Part #
4463TK
NB180
NB181
NB591
4575TK
9088
9087
KSM
3623
NB141
NB274
4852TK
NB608
NB518
NB560
9023MOD
4461TK
NB597
10385
1
2
3
4
5
6
7
8
5/16-18 Nyloc Nut
5/16-18 X 1 1/2 Torx Pan ZP
Console Weldment
Key Switch Lock Washer
Key Switch Nut
Key Switch ON-OFF, 2 Prong
Key Switch ( 12-VOLT )
1/4-20 X 2 1/2 HCC GR2 ZP
1/4 SAE Washer
Console Mount Plate
1/4-20 Wing Nut ZP
1/4 X 1 1/2 Clevis Pin
1/4-20 X 1 1/4 HCC GR5 ZP
Clutch Cable Clevis
16
15
10
13
17
10
1
2
14
9
18
10
11
12
13
14
15
16
17
18
3
5
19
12
10
4
6
Link for Console
3/32 X 3/4 Cotter Pin
Wiring Harness B&S (RECOIL)
Wiring Harness B&S (12-VOLT)
Engage Cable
11
7
10299
BR20CC
8
19
10
9
ENGINE TO BLADE PULLEY
CONFIGURATION
FIGURE 9
WIRING DIAGRAM ( manual start )
FIGURE 10
P/N 4846
P/N B527
P/N BA50
WIRING DIAGRAM ( 12-VOLT )
FIGURE 11
P/N BB105
When ordering replacement parts
* = USE PAINT CODE:
TC=TEX.RED,S=SILVER,TK=TEX.BLACK
Download from Www.Somanuals.com. All Manuals Search And Download.
14
REPAIR PARTS
Your 44’’ Trailcutter has been produced with components designed specific to this
machine. Although standard V-belts, springs, bearings, blades, pulleys, hardware, etc.
look similar to parts used on other machinery, they may in some cases be made of a
different construction and/or materials.
8
10
9
7
2
1
6
5
2
4
Item #
1
2
3
Description
Battery Box
Wiring Harness
Key Switch
Part #
10298TK
10299
3623
3
4
5
6
7
8
Key Switch Nut
Key Switch Lock Washer
Decal On / Off
Tank Mount Weldment
Gas Tank Mount
9087
9088
OD28
10736TK
6078TK
H11
9
Lock Pin
10
Gas Tank Assembly
6059
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Not Shown
Sold Separately
12 volt Wiring Harness ( Engine)
M6-1.0 Nut Yellow Zinc
Solenoid Assembly 12 Volt
Battery Hold Down, 15" Tarp Strap
Battery Cable (Black 10")
Battery Cable (10" Red)
Battery Cable Small Rubber Boot
Battery Pad
NB600
10806
BHOLD
BCS
BCSR
BCBT
BATPAD
N/A
Battery (U1R)
When ordering replacement parts
* = USE PAINT CODE: TC=TEX.RED,S=SILVER,TK=TEX.BLACK
Download from Www.Somanuals.com. All Manuals Search And Download.
15
44”ROUGH CUT
TRAILCUTTER
swisherinc.com
Each mower has its own model number. Each engine has its
own model number. The model number for the mower will be
found on the right hand side of the motor mount. The model
number for the engine will be found on the top of the blower
fan housing.
All mower parts listed herein may be ordered directly from
Swisher Mower & Machine Co. Inc. or your nearest Swisher
dealer.
OWNER’S
MANUAL
All engine parts may be ordered from the nearest dealer of the
engine supplied with your mower.
MODEL NO.
RTB115441
RTB134412V
RTB14544
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT – 44’’ TRAILCUTTER
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
* ENGINE MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER MOWER & MACHINE CO., INC.
1602 CORPORATE DRIVE; P.O. BOX 67
WARRENSBURG, MO 64093
SWISHER MOWER & MACHINE CO.,INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTED IN U.S.A.
|