™
Sun StorageTek 4 Gb FC NEM
20-Port Host Bus Adapter
User’s Guide
For HBA Model SG-XPCIE20FC-NEM-Z
Sun Microsystems, Inc.
Part No. 819-7929-12
February 2008, Revision A
Submit comments about this document at: http://www.sun.com/hwdocs/feedback
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface xi
1. Network Express Module Overview
1
System Interoperability
4
6
2. Hardware Installation and Removal
7
▼
▼
Configuring the NEM For Hot-Plug Operation 14
Using the ILOM Web Interface 14
Using the ILOM Command-Line Interface 15
Verifying a Hot-Insert Operation 16
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
▼
Replacing a NEM 19
▼
▼
▼
3. HBA Software Installation 23
Driver Software for the Solaris OS 23
Solaris Diagnostic Support 23
Driver Software for Linux OSs 24
Red Hat Enterprise Linux 24
Novell SUSE Linux Enterprise Server 24
▼
▼
▼
To Build the Linux 2.6 Driver 25
▼
4. Release Notes 29
Solaris OS-Specific Issues 30
SUSE Linux Enterprise-Specific Issues 30
Windows Server 2003 OS-Specific Issues 30
A. Declaration of Conformity, Regulatory Compliance, and Safety Statements 31
iv
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity 33
Safety Agency Compliance Statement 35
Regulatory Compliance Statements 47
Index 51
Contents
v
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
This guide describes how to install and remove the Sun StorageTek™ 4 Gb Fibre
Channel (FC) Network Express Module (NEM) Host Bus Adapter (HBA), 20-port
pass-through RoHS 5 compliant module. This document is written for technicians,
system administrators, application service providers (ASPs), and users who have
advanced experience troubleshooting and replacing hardware.
How This Document Is Organized
systems, host platforms, switches, and storage systems that support the NEM.
Chapter 2 describes how to install and remove the NEM.
Chapter 3 describes how to download and install the HBA drivers and patches.
Chapter 4 contains the latest supplementary information for the preceding chapters.
Appendix A provides the required product safety information.
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Using UNIX Commands
This document might not contain information about basic UNIX commands and
procedures such as shutting down the system, booting the system, and configuring
devices. Refer to the following for this information:
®
■
Software documentation that you received with your system
Solaris™ Operating System documentation, which is at:
■
Shell Prompts
Shell
Prompt
C shell
machine-name%
C shell superuser
machine-name#
Bourne shell and Korn shell
Bourne shell and Korn shell superuser
$
#
xii
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Typographic Conventions
*
Typeface
Meaning
Examples
AaBbCc123
The names of commands, files,
and directories; on-screen
computer output
Edit your.loginfile.
Use ls-ato list all files.
% You have mail.
AaBbCc123
What you type, when contrasted % su
with on-screen computer output
Password:
Book titles, new words or terms, Read Chapter 6 in the User’s Guide.
AaBbCc123
words to be emphasized.
Replace command-line variables
with real names or values.
These are called class options.
You must be superuser to do this.
To delete a file, type rmfilename.
*
The settings on your browser might differ from these settings.
Related Documentation
The documents listed are available at:
Title
Part Number
819-0139-nn
819-5647-nn
819-5651-nn
819-5846-nn
Solaris Fibre Channel and Storage Multipathing Administration Guide
Sun Blade 8000 Series Installation Guide
Sun Blade 8000 Series Product Notes
Sun Blade 8000 Series Online Help System
Preface
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Documentation, Support, and Training
Sun Function
Documentation
Support
URL
Training
Third-Party Web Sites
Sun is not responsible for the availability of third-party web sites mentioned in this
document. Sun does not endorse and is not responsible or liable for any content,
advertising, products, or other materials that are available on or through such sites
or resources. Sun will not be responsible or liable for any actual or alleged damage
or loss caused by or in connection with the use of or reliance on any such content,
goods, or services that are available on or through such sites or resources.
Sun Welcomes Your Comments
Sun is interested in improving its documentation and welcomes your comments and
suggestions. You can submit your comments by going to:
Please include the title and part number of your document with your feedback:
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide, part number 819-
7929-12
xiv
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Contact Information
If you need help installing or using this product, call 1-800-USA-4SUN, or go to:
Preface
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
xvi
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
1
Network Express Module Overview
describes the various operating systems, host platforms, storage, and infrastructure
configurations that support the NEM. This chapter contains the following topics:
■
■
■
“NEM Features and Specifications” on page 1
“Operating System Requirements” on page 4
“System Interoperability” on page 4
NEM Features and Specifications
The Sun StorageTek 4 Gb FC NEM 20-Port HBA consists of a 20-port NEM bus
expansion board that interfaces a FC optical media bus. The NEM provides closed
chassis adapter installation, removal, integrated hot-plug, and protection from
electrostatic discharge (ESD) handling damage.
The 20-port NEM consists of ten independent HBAs. Each HBA has two FC ports
which provide exclusive connections to a single blade. The ports of each HBA cannot
be shared with any other blade in the chassis.
The NEM supports 20 independent FC buses operating at 4.25 Gbits/sec. It is also
backward compatible with 2.125-Gbit/sec and 1.0625-Gbit/sec devices. Small-Form
Factor (SFF) optical transceivers are used to connect to the external FC buses.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Twenty SFP fiber-optic transceivers are included with each NEM. You can order
additional NEMs and SFP transceivers from Sun Microsystems using the following
part numbers:
Description
Part Number
4 Gb FC NEM 20-port HBA
SG-XPCIE20FC-NEM-Z
4 pack of Small-Form Pluggable shortwave FC optical XSFP-SW-4GB-4PK
rates (RoHS-5 compliant)
Small-Form Pluggable shortwave FC optical
transceiver capable of 4 Gb, 2 Gb, and 1 Gb transfer
rates (RoHS-5 compliant)
XSFP-SW-4GB
See TABLE 1-1 for a list of the NEM’s features.
TABLE 1-1
NEM Features and Specifications
Feature
Description
NEM interface
FC interface
FC topology
PCI Express ten x8 (ten x4 active links)
Dual port 4, 2, 1 Gbps auto-speed negotiation
Point-to-point (N-port), Arbitrated Loop (NL_port) and
Switched Fabric (N_port)
PCI transfer rate (maximum)
Onboard memory
PCI Express Generation One (2.5 Gbps) x4
One 4-MB flash ROM per chip, 40 MB total, field-
programmable
One 1.5 MB SRAM per chip, 15 MB total NEM SRAM
ID chip
Enables the HBA worldwide names (WWNs) to be
retained when a NEM is replaced. See “ID Chip
Feature” on page 3 for more information.
External FC connectors
Small Form-Factor Pluggable (SFP) multimode optic
with LC-style connector
Maximum FC cable length
1 Gbps: 500 meters using 50/125 µm core fiber
300 meters using 62.5/125 µm core fiber
2 Gbps: 300 meters using 50/125 µm core fiber
150 meters using 62.5/125 µm core fiber
4 Gbps: 150 meters using 50/125 µm core fiber
70 meters using 62.5/125 µm core fiber
2
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 1-1
Feature
NEM Features and Specifications (Continued)
Description
LED indicators
A blue (Ready to Remove), yellow (Service Action
LED on the front panel.
Two LEDs per channel (green and yellow) on the front
panel used to indicate port status.
Buttons
Attention button to support hot-swap functionality.
Locator button to assist in locating the module. (See
FIGURE 2-5 for button locations.)
Form Factor
PCI Network Express Module
ID Chip Feature
The 20-port NEM has an ID chip on it that contains an Electrically Erasable Read
Only Memory (EEPROM). This EEPROM stores the worldwide names (WWNs) for
each of the ten HBAs and 20 FC ports on the NEM.
When you replace a failed NEM that is running firmware prior to version 2.72a, each
of the ten HBAs and 20 FC ports on the NEM is assigned new port and node WWNs.
Thus, you must update SAN components, such as FC switches and storage arrays,
with the new WWN values.
However, if the failed NEM is running firmware version 2.72a, at minimum, you can
retain the existing HBA and FC port WWNs by removing the ID chip from the failed
NEM and installing the chip on the replacement NEM. Thus, you do not have to
update any SAN components as part of the NEM replacement. In order for the ID
chip feature to work, the replacement NEM must be running firmware version 2.72a,
at minimum.
For information about determining and updating the firmware version, see the
following Emulex documents:
■
Solaris:
Note – For the Solaris OS, the 2.72a firmware is embedded in the emlxs driver
version 2.21g, at minimum. This driver is part of s10u5 and available as Solaris 10
patch 120223-22 or 120222-22 at:
■
Chapter 1 Network Express Module Overview
3
Download from Www.Somanuals.com. All Manuals Search And Download.
■
Windows: www-
If you replace the failed NEM (regardless of firmware version) and do not swap the
ID chip, new WWNs are assigned to each of the ten HBAs and 20 FC ports; thus,
requiring you to update SAN components with the new WWN values.
For more information about replacing a failed NEM, see “Replacing a NEM” on
page 19.
Operating System Requirements
The NEM requires the operating system (OS) levels listed in TABLE 1-2.
TABLE 1-2
Supported Operating System Versions
Operating System
Supported Versions
Solaris (x64)
Solaris 10 11/06, Solaris 10 06/06, or Solaris 10 01/06 and latest
patches 119131, 120222, and 120223
*
Solaris 10, latest patches 119255, 119131, 120222, and 120223 plus
\
packages SUNWemlxsand SUNWemlxu
Linux
Red Hat Enterprise Linux (RHEL) 4 Update 3 and Update 4 x64
SUSE Linux Enterprise Server (SLES) 9 SP3 x64
Windows Server 2003 Enterprise Edition x64
Microsoft Windows
Windows Server 2003 Enterprise Edition x86 w/SP1
Windows Server 2003 Standard Edition x86 w/SP1
*
\ Packages are available for download at: the Sun Download Center (SDLC).
This section provides information about selected platforms, storage systems, and
switches that are compatible with the heterogeneous FC network design of the NEM.
This section contains the following topics:
■
“Host Platform Support” on page 5
“Storage System Support” on page 5
■
4
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
■
“Fibre Channel Switch Support” on page 6
Host Platform Support
The NEM is supported by the platforms and operating systems (OSs) listed in
TABLE 1-3.
TABLE 1-3
Platform
Platform and Operating System Support
Supported OSs
Sun Blade™ 8000 Modular System
Sun Blade 8000 P Modular System
Sun Solaris, Linux, and Windows
Sun Solaris, Linux, and Windows
You can install the NEM in an available NEM slot of the Sun Blade 8000 Chassis or
Sun Blade 8000 P chassis.
For information about updating the ILOM firmware for the chassis monitoring
module (CMM) or the service processor (SP) go to
http://www.sun.com/servers/blades/8000/downloads.jsp. For firmware
upgrade instructions, see Preparing to Upgrade the ILOM Firmware in the Sun Blade
8000 Series Online Information System.
Storage System Support
The NEM supports the following storage systems:
■
Sun StorEdge™ 3510 and 3511 FC Arrays (see “Using the NEM With Sun
StorEdge 3510 and 3511 Arrays” on page 29)
■
■
■
■
■
■
■
Sun StorEdge 6020 and 6120 Arrays
Sun StorEdge 6130 Array
Sun StorageTek 6140 Array
Sun StorageTek 6540 Array
Sun StorageTek FlexLine™ 380 Storage System
Sun StorEdge 6320 system
Sun StorEdge L25 and L100 tape libraries with Fibre Channel / LVD Internal
Bridge
■
■
■
Sun StorEdge C4 tape library with LVD SCSI to Fibre Channel Card
Sun StorEdge L500 tape library
Sun StorEdge L180, L700 tape libraries
Chapter 1 Network Express Module Overview
5
Download from Www.Somanuals.com. All Manuals Search And Download.
■
Sun StorEdge L5500, L8500 tape libraries
Fibre Channel Switch Support
The NEM is supported with the following FC switches:
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
2 Gb QLogic SANbox 5200 switch
4 Gb QLogic SANbox 5600 and 5602 Stackable FC switches
2 Gb Brocade SilkWorm 3200 and 3800 switches
2 Gb Brocade SilkWorm 3250 and 3850 switches
2 Gb Brocade SilkWorm 3900 switch
2 Gb Brocade SilkWorm 12000 and 24000 directors
4 Gb Brocade SilkWorm 4100 switch
4 Gb Brocade SilkWorm 4900 switch
4 Gb Brocade SilkWorm 48000 and 200E
2 Gb McDATA Sphereon 4300 switch
2 Gb McDATA Sphereon 4500 switch
4 Gb McDATA Sphereon 4400 and 4700 switches
2 Gb McDATA Intrepid 6064 director
2 Gb McDATA Intrepid 6140 director
2 Gb McDATA Intrepid i10K director
6
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
2
Hardware Installation and Removal
This chapter describes the tasks required to install and remove the NEM when the
Sun Blade 8000 Modular System is in a powered-on state.
This chapter contains the following topics:
■
■
■
■
■
“Observing ESD and Handling Precautions” on page 8
“Installing the NEM” on page 8
“Configuring the NEM For Hot-Plug Operation” on page 14
“Verifying a Hot-Insert Operation” on page 16
“Replacing a NEM” on page 19
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Observing ESD and Handling
Precautions
Caution – Damage to the NEM can occur as the result of careless handling or
electrostatic discharge (ESD). Always handle the NEM with care to avoid damage to
electrostatic sensitive components.
To minimize the possibility of ESD-related damage, Sun strongly recommends using
both a workstation antistatic mat and an ESD wrist strap. You can get an ESD wrist
strap from any reputable electronics store or from Sun as part number #250-1007.
Observe the following precautions to avoid ESD-related problems:
■
Leave the NEM in its antistatic bag until you are ready to install it in the system.
■
Always use a properly fitted and grounded wrist strap or other suitable ES
protection when handling the NEM and observe proper ESD grounding
techniques.
■
Place the NEM on a properly grounded antistatic work surface pad when it is out
of its protective antistatic bag.
Installing the NEM
This section describes the process for installing a new Network Express Module
(NEM) in a powered-on Sun Blade 8000 or Sun Blade 8000 P system.
Note – If you are installing the NEM in a new Sun Blade 8000 or Sun Blade 8000 P
system that has not yet been powered on, follow the installation instructions in the
Sun Blade 8000 Series Installation Guide.
■
■
To Install the NEM
To Connect the Optical Cables
The following sections describe these steps in more detail.
8
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
▼ To Install the NEM
1. Attach an antistatic strap (refer to “Observing ESD and Handling Precautions”
on page 8).
2. Refer to your system installation or service manual to determine an
appropriate slot in which to install the NEM.
3. Unpack the NEM and remove it from the antistatic bag.
4. Locate a vacant NEM slot in the back of the chassis. Ensure the label on top of
the NEM is facing up.
5. Align the NEM with the vacant slot.
Ensure that the NEM’s port connectors are facing toward you and that the NEM
ejector levers are fully opened.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
9
FIGURE 2-1 NEM Ejector Levers
6. Align the NEM with the chassis guidance system and slide the NEM into its
slot (see FIGURE 2-2).
Ensure that the NEM engages with the system chassis guidance system. Failure
to align the NEM correctly can result in damage with the internal connection to
the chassis midplane.
10
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2-2 Inserting the NEM Into the Chassis
7. Push the ejector levers toward each other and close the levers to secure the
NEM in its slot.
After you physically install the NEM in its slot, the Chassis Monitoring Module
(CMM) will automatically detect the presence of the NEM. The OK LED goes to
8. Press the Attention button to notify the blades (host operating systems) of the
presence of the NEM.
9. Verify that the NEM is working properly.
See “To Verify NEM Status” on page 17.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
11
▼ To Connect the Optical Cables
Note – The NEM does not allow normal data transmission on an optical link unless
it is connected to another similar or compatible Fibre Channel (FC) product (that is,
multimode to multimode).
Use multimode fiber-optic cable, intended for short-wave lasers, that adheres to the
specifications in TABLE 2-1.
TABLE 2-1
Optical Cable Specifications
Fiber-Optic Cable
Maximum Length
Minimum Length
Connector
62.5/125 µm
300 meters at 1.0625 Gbps
150 meters at 2.125 Gbps
70 meters at 4.25 Gbps
2 meters
LC
(multimode)
50/125 µm
500 meters at 1.0625 Gbps
300 meters at 2.125 Gbps
150 meters at 4.25 Gbps
2 meters
LC
(multimode)
Follow these steps when connecting the optical cables:
1. Connect each fiber-optic cable to an LC connector on the NEM (see FIGURE 2-3).
The ports are numbered 0-9 right-to-left as viewed from the back of the chassis.
Each NIC has two external network ports. For each pair of external ports (for
each blade), the top is port 0 and the bottom is port 1.
12
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 2-3 Connecting the Optical Cables
2. Connect the other end of each cable to a FC device.
For Hot-Plug Operation” on page 14.
3. Observe the light-emitting diodes (LEDs) status for the power-on self test
(POST).
Each port has a corresponding set of LEDs that provide a visual indication of the
operating state. See FIGURE 2-4 to determine the location of the port LEDs.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
13
FIGURE 2-4 Port Level LEDs
TABLE 2-2 summarizes port LED indicator combinations.
TABLE 2-2
Port LED Indicator Status Definitions
Green LED
On
Yellow LED
1 Fast blink
2 Fast blinks
3 Fast blinks
Off
State
1-Gb Link Rate - Normal operating state, link up
2-Gb Link Rate - Normal operating state, link up
4-Gb Link Rate - Normal operating state, link up
Wake-up failure (board failed)
POST failure (board failed)
Wake-up failure monitor
On
On
Off
Off
On
Off
Slow blink
Fast blink
Flashing
Off
Off
Failure in POST
Off
POST processing in progress
Failure while functioning
On
On
On
Failure while functioning
Slow blink
Slow blink
Slow blink
Slow blink
Slow blink
Off
Normal, link down
On
Not defined
Slow blink
Fast blink
Flashing
Off-line for download
Restricted off-line mode (waiting for restart)
Restricted off-line mode, test active
14
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the NEM For Hot-Plug
Operation
To insert a NEM into the chassis while the system is running, you need to:
1. Physically install the module.
2. Prepare the NEM for hot-insertion by using the CMM integrated lights-out
management (ILOM) web interface or command-line-interface (CLI) and verify
the NEM has returned the expected feedback.
See “To Verify NEM Status” on page 17.
3. Verify in one of the ILOM interfaces that the module’s Ready to Remove status
is Not Ready.
Using the ILOM Web Interface
1. Log in to the ILOM web interface using the IP address of the active Chassis
Monitoring Module.
The first page of the ILOM web interface is displayed.
2. In the left navigation pane, select CMM.
The ILOM Version Information page is displayed.
3. Select the System Information tab, and then the Components tab.
The Component Management page is displayed. If you have installed a new
NEM, go to Step 4.
When you were preparing a NEM for a hot-remove, if you selected Prepare to
Remove from the Component Management page and corrected the problem
without removing the NEM or if you decided not to remove the NEM, complete
Step 3a and Step 3b.
a. Select the radio button next to the NEM that you want to hot-insert.
If you select the wrong NEM, click on the deselect icon at the top of the radio
button column.
b. From the Actions drop-down list, select Return to Service.
When you select the Return to Service option, the system recognizes the
inserted NEM, changes its Ready to Remove status to Not Ready, and lights
the NEM’s green OK indicator.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
15
4. Verify that the selected NEM has returned the expected feedback.
See “To Verify NEM Status” on page 17.
1. Log in to the ILOM CLI of the active Chassis Monitoring Module.
2. For a list of components in your system, type:
show /CH
3. If you installed a new NEM, go to Step 4.
When you were preparing a NEM for a hot-remove, if you corrected the problem
without removing the NEM or you decided not to remove the NEM, complete
the following steps:
a. Type this command to prepare a component for a hot-insert:
set /CH/component return_to_service_action=true
For example:
set /CH/NEM1 return_to_service_action=true
b. Use the show /CH/component command to list the status of the connection
from the NEM to each of the blades.
Note – The following example depicts only the link status portion of the show
/CH/component command output.
-> show /CH/NEM1
blade0_link_status = Not_connected
blade1_link_status = Not_connected
blade2_link_status = Not_connected
blade3_link_status = Not_connected
blade4_link_status = Not_connected
blade5_link_status = Not_connected
blade6_link_status = Connected
blade7_link_status = Not_connected
blade8_link_status = Not_connected
fault_state = OK
clear_fault_action = (none)
prepare_to_remove_status = NotReady
16
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
c. If all blades that you expect to be connected show a Connectedlink status,
go to Step 4. Otherwise, if a blade that you expect to be connected has a link
status of Not connected, perform Step a - Step b again until its link status
is Connected.
4. To verify that the NEM Ready to Remove status has changed to Not Ready,
type:
The system returns:
prepare_to_remove_status = Not Ready
5. Verify that the selected NEM has returned the expected feedback.
See the “To Verify NEM Status” on page 17.
Verifying a Hot-Insert Operation
You can replace many components in the chassis while the system is running by
using a hot-plug procedure.
1. Physically install the module.
2. Verify in one of the ILOM interfaces that the module’s Ready to Remove status
is Not Ready and that the module has returned the expected feedback.
See “To Verify NEM Status” on page 17.
You can use the ILOM web interface or ILOM CLI to verify.
Using the ILOM Web Interface
1. Log in to the ILOM web interface using the IP address of the active Chassis
Monitoring Module.
The first page of the ILOM web interface is displayed.
2. In the left navigation pane, select CMM (Chassis Monitoring Module).
The ILOM Version Information page is displayed.
3. Select the System Information tab, and then the Components tab.
The Component Management page is displayed.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
17
4. Verify that the selected NEM has returned the expected feedback.
See “To Verify NEM Status” on page 17.
Using the ILOM CLI
1. Log in to the ILOM CLI of the active Chassis Monitoring Module.
2. For a list of components in your system, type:
show /CH
3. To verify that the NEM Ready to Remove status has changed to Not Ready,
type:
The system returns:
prepare_to_remove_status = Not Ready
4. Verify that the selected NEM has returned the expected feedback.
▼ To Verify NEM Status
See TABLE 2-3 for a description of the LED states for the NEM. See FIGURE 2-5 for the
location of the LEDs, Attention button, and Locator button.
1. Check the following LEDs to verify that the NEM is ready for a hot-plug
insertion.
■
Green OK LED goes to Standby.
2. Activate the NEM by pressing the Attention button, and the green OK LED
goes to Slow blink.
■
When all links to active blades have been made, the green OK LED goes to Solid
On.
18
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
■
Ready to Remove status shows Not Ready in the ILOM interfaces.
NEM LED Status
TABLE 2-3
Ready-to-Remove
LED
Color: Blue
Location: Top
Service Action
Required LED
Color: Yellow
OK LED (Power, Attention,
and Connected)
Color: Green
Status
Location: Middle
Location: Bottom
On
Off
Off
Off
Off
Off
On
Off
Off
Off
Off
Ready to remove
Off
Service attention required
Standby
Very slow blink
Slow blink
On
Connecting links to blades
Links connected to blades
FIGURE 2-5 LEDs, Attention and Locator Buttons
The Attention button enables you to activate (if inserting) or prepare to remove (if
removing) a NEM during a hot-plug operation.
The Locator button, when pressed momentarily, flashes a white light to assist in
locating the module. You can also activate the Locator LED remotely by executing a
command on the CMM.
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Replacing a NEM
If a NEM fails or if you choose to change the I/O configuration, you will need to
replace it. You can remove and replace a NEM from a powered-on system using a
hot-plug operation, as well as from a powered-off system. When you remove a
NEM, you must replace the module within two minutes to prevent adjacent modules
from overheating.
If you are removing but not replacing the NEM, you also must install a NEM filler
panel to meet FCC limits for electromagnetic interference (EMI) and to ensure
proper airflow and cooling. If you encounter a problem with the NEM replacement,
see the Sun Blade 8000 Series Online Help System for troubleshooting steps.
▼ To Install the ID Chip Patch
1. Download patch 120223-22 or 120222-22 from SunSolve:
2. Install the patch onto each of the HBAs in the NEM.
Follow the installation instructions included in the patch Readme file.
▼ To Remove a NEM
1. Identify which NEM to replace.
If the yellow Service Action Required LED is lit, this indicates a problem with the
NEM and you might choose to replace it. Otherwise, if you want to change the
I/O configuration, you can choose any NEM to replace.
2. Prepare the NEM for a hot-plug procedure using either of these methods:
a. Press the Attention button on the NEM to initiate the hot-plug removal.
b. Use the ILOM web interface or the CLI to initiate the hot-plug removal.
If the NEM fails the hot-plug preparation and its Ready-to-Remove LED does not
light, see the Sun Blade 8000 Series Online Help System for troubleshooting steps.
3. When the blue Ready-to-Remove LED is lit on the NEM, physically remove the
NEM.
a. Remove all cables from the NEM.
20
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Press the latch on both ejector levers inward at the same time.
c. Swing out the ejector levers to their fully open position.
d. Slide the NEM out of its slot.
Support the weight of the NEM with one hand at the bottom of the NEM.
▼ To Replace the ID Chip
1. After you have removed the failed NEM from the chassis, locate the ID chip at
the back of the board (see FIGURE 2-6).
FIGURE 2-6 Location of ID Chip
2. Grasp the edges of the ID chip and pull straight up to remove it from the
board.
3. Remove the ID chip from the new NEM, and install it onto the failed board
that you will be returning to Sun.
4. Install the ID chip onto the new board (see FIGURE 2-7).
Chapter 2 Hardware Installation and Removal
Download from Www.Somanuals.com. All Manuals Search And Download.
21
a. Position the notched side of the ID chip to the left.
b. Place the ID chip directly over the connector.
c. Press down easily to seat the ID chip to the connector.
FIGURE 2-7 Installing the ID Chip
5. Install the replacement NEM into the chassis and reconnect the cables.
22
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
3
HBA Software Installation
this chapter for your operating system to install the HBA driver and any other
utilities required for your installation.
This chapter contains the following topics:
■
■
■
■
“Driver Software for the Solaris OS” on page 23
“Driver Software for Linux OSs” on page 24
“Driver Software for Windows 2003 OS” on page 26
“Configuration and Diagnostic Utilities” on page 26
Driver Software for the Solaris OS
The latest HBA driver for the Solaris OS is included with Solaris 10 patch 120223-22.
See “Operating System Requirements” on page 4 for more information.
Solaris Diagnostic Support
Diagnostic support for the HBA is included in the SunVTS™ software beginning
with version 6.3. The SunVTS software is included with Solaris 10 11/06. It is also
available for download at:
The emlxtestutility supports the following functions:
■
Connectivity verification
■
Firmware version and checksum test
23
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
Self-test
Loopback tests
■
■
■
■
External
Internal, single-bit
Internal, 10-bit
Mailbox
Driver Software for Linux OSs
The Sun StorageTek 4 Gb FC NEM 20-Port HBA is supported by Red Hat Enterprise
Linux (RHEL) 4 U3 and U4 and Novell SUSE Linux Enterprise Server 9 Service Pack
3 (SLES9-SP3).
Red Hat Enterprise Linux
The HBA driver distributed with Red Hat Enterprise Linux (RHEL) 4 U3 and U4
supports the NEM. No additional driver updates are required.
Novell SUSE Linux Enterprise Server
The HBA driver distributed with SUSE Linux Enterprise Server 9 Service Pack 3
(SLES9-SP3) has the following known problems:
■
The HBA driver does not recognize the NEM device and will prevent it from
loading.
■
A system panic occurs when the HBA driver is unloaded.
To resolve these problems, update to the Emulex driver version 8.0.16.27 as
described in the next section.
▼ To Update the Driver
1. Run /sbin/update-pciids.
This command uploads the latest database which contains all supported PCI
devices by Linux, including the NEM.
24
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Run YaST online.
You will be notified that the 8.0.16.27 is being installed.
Note – If you are running on a 2.6.5-7.244 kernel, you must install the Emulex
8.0.16.27 driver manually instead of updating using YaST. The driver RPM is
contained on the resource CD.
▼ To Install SLES9-SP3 to FC Disk
Before starting this procedure, you will need to create a driver update disk using the
ISO image for driver vesion 8.0.16.27 provided on the Sun Blade 8000 Series
Modular Systems resource CD. You can also download the Emulex driver update
disk from the Emulex or Novell support web site.
Emulex web site:
Novell web site:
To update the driver to version 8.0.16.27:
2. When prompted for the update disk, load the driver update CD.
3. Continue the installation until all files are installed and the system reboots.
4. After the system reboots, follow the steps described in “To Update the Driver”
on page 24.
▼ To Build the Linux 2.6 Driver
You can build your own HBA driver by downloading the archived sources from the
Emulex support site.
1. To download the archived sources, go to:
2. Click the Linux 2.6 Kernel link.
Chapter 3 HBA Software Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
25
3. Follow the instructions in the README file to build and install the 8.0.16.27
driver.
Driver Software for Windows 2003 OS
The HBA driver for Windows 2003 OS is available for download at the Emulex
support site for Sun Microsystems.
▼ To Install Windows OS Driver and Application
Kits
Follow these steps to download the driver and AutoPilot installer:
1. Go to the Emulex support site for Sun Microsystems at:
2. Locate the driver section for Windows.
3. Download the Driver Kit by clicking the Download icon.
4. Click the PDF Manual icon to download installation, configuration, and
troubleshooting information for the Windows OS.
5. Install the driver and management utilities for the Windows OS as described
in the Emulex installation guide you downloaded in the previous step.
Configuration and Diagnostic Utilities
Use the HBAnywhere Remote Management Utility or the lputilcommand-line
interface (CLI) utility to configure the HBA. These utilities are available for Linux
and the Windows OS and provide support for the following functions:
■
■
■
■
Discover local and remote hosts, HBAs, targets, and LUNs
Reset HBAs
Set HBA driver parameters
Update firmware
26
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
■
■
■
■
Enable or disable the system BIOS
Run diagnostic tests on HBAs
Manage out-of-band HBAs
Manage local and in-band remote HBAs
See the Linux or Windows OS Emulex user manual for more information about
using the HBAnywhere and lputilutilities.
Chapter 3 HBA Software Installation
27
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER
4
chapters in this guide. It contains the following topics:
■
■
■
■
Using the NEM With Sun StorEdge 3510 and 3511 Arrays
Solaris OS-Specific Issues
SUSE Linux Enterprise-Specific Issues
Windows Server 2003 OS-Specific Issues
For additional information related to the Sun StorageTek 4 Gb FC NEM 20-Port
HBA, see the Sun Blade 8000 Module System documentation set.
Using the NEM With Sun StorEdge 3510
and 3511 Arrays
You cannot connect the Sun StorEdge 3510 RAID array or Sun StorEdge 3511 FC
with SATA RAID array to the NEM on the same channel that use different speeds (1
Gb and 2 Gb). You can, however, mix 1-Gb and 2-Gb FC HBAs on different controller
channels. This limitation is due to the design of the Sun StorEdge 3510 RAID array's
port bypass circuitry and the inability of FC to support auto-negotiation in a multi-
drop loop configuration.
Host connectors channels 4 and 5 of the 3511 FC cannot auto-negotiate to 1 Gbit
which limits the number of hosts that can be direct-attached using 1 Gbit HBAs.
Channels 0 and 1 are able to auto-negotiate to 1 Gbit and allow up to four
connections in a dual-controller configuration or two connectors each in a single-
controller configuration.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Solaris OS-Specific Issues
The following known issues are related to installing, configuring, or operating the
NEM with the Solaris 10 OS.
Out of Option ROM Memory Error in System
BIOS
Problem: A fully populated Sun Blade 8000 chassis with at least one NEM installed,
could cause the OutofOptionROMMemorySpaceerror to occur during BIOS
POST.
Workaround: Disable some of the slots in the Basic Input/Output System (BIOS)
using the BIOS Setup utility. For information about disabling Option ROM, see BIOS
Option ROMs in the Sun Blade 8000 Series Online Information System.
For information about how to boot from a FC storage device connected to the NEM,
see Appendix A in the Sun Blade 8000 Series Installation Guide.
SUSE Linux Enterprise-Specific Issues
Problem: The HBA driver distributed with SUSE Linux Enterprise Server 9 Service
Pack 3 (SLES9-SP3) has the following known problems:
■
The HBA driver does not recognize the NEM device and will prevent it from
loading.
■
A system panic occurs when the HBA driver is unloaded.
Workaround: To resolve these problems, update to the Emulex driver version
8.0.16.27 as described in “To Update the Driver” on page 24.
Windows Server 2003 OS-Specific Issues
See the Emulex driver manuals for any known issues with the Windows OS drivers.
30
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
A
Declaration of Conformity,
Regulatory Compliance, and Safety
This appendix contains the following information that applies to the Sun StorageTek
4 Gb FC NEM 20-Port HBA:
■
■
■
“Declaration of Conformity” on page 33
“Safety Agency Compliance Statement” on page 35
“Regulatory Compliance Statements” on page 47
31
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
<<
Declaration of Conformity
Compliance Model Number:
Product Family Name:
375-3385-XX
Sun StorageTek 4 Gb FC NEM HBA
EMC
USA - FCC Class A
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This equipment may not cause harmful interference.
2) This equipment must accept any interference that may cause undesired operation.
Manufactured by Emulex Corporation
European Union
This equipment complies with the following requirements of the EMC Directive 89/336/EEC:
As Information Technology Equipment (ITE) Class A per (as applicable):
EN 55022:1994 +A1:1995 +A2:1997
Class A
EN 61000-3-2:2000 +A2:2005
EN 61000-3-3:1995 +A1:2001
Pass
Pass
EN 55024:1998 +A1: 2001 +A2:2003 Required Limits:
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
4 kV (Direct), 8 kV (Air)
3 V/m
1 kV AC Power Lines, 0.5 kV Signal and DC Power Lines
1 kV AC Line-Line and Outdoor Signal Lines, 2 kV AC Line-Gnd, 0.5 kV DC Power Lines
3 V
1 A/m
Pass
Safety
This equipment complies with the following requirements of Low Voltage Directive 73/23/EEC:
EC Type Examination Certificates:
EN 60950-1:2001, 1st Edition
IEC 60950-1:2001, 1st Edition
Evaluated to all CB Countries
CB Scheme Certificate No. US-TUVR-3269
UL and cUL/CSA 60950-1:2001, CSA C22.2 No. 60950-00
FDA DHHS Accession Number (Monitor Only)
File: E157779
vol. x3
Supplementary Information: This equipment was tested and complies with all the requirements for the CE Mark.
This equipment complies with the Restriction of Hazardous Substances (RoHS) directive 2002/95/EC.
______________________/S/____________________
_____________________/S/___________________
Dennis P. Symanski
DATE
Donald Cameron
DATE
Worldwide Compliance Office
Sun Microsystems, Inc.
4150 Network Circle, MPK15-102
Santa Clara, CA 95054, USA
Tel: 650-786-3255
Program Manager/Quality Systems
Sun Microsystems Scotland, Limited
Blackness Road, Phase I, Main Bldg
Springfield, EH49 7LR
Scotland, United Kingdom
Tel: +44 1 506 672 539
Fax: 650-786-3723
Fax: +44 1 506 670 011
33
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Depending on the type of power switch your device has,
one of the following symbols may be used:
Safety Agency Compliance
Statement
Read this section before beginning any procedure. The
following text provides safety precautions to follow when
installing a Sun Microsystems product.
On – Applies AC power to the system.
Off – Removes AC power from the system.
Safety Precautions
For your protection, observe the following safety
precautions when setting up your equipment:
Standby – The On/Standby switch is in the
standby position.
■
■
Follow all cautions and instructions marked on the
equipment.
Modifications to Equipment
Do not make mechanical or electrical modifications to the
equipment. Sun Microsystems is not responsible for
regulatory compliance of a modified Sun product.
Ensure that the voltage and frequency of your power
source match the voltage and frequency inscribed on
the equipment’s electrical rating label.
■
Never push objects of any kind through openings in
the equipment. Dangerous voltages may be present.
Conductive foreign objects could produce a short
circuit that could cause fire, electric shock, or damage
to your equipment.
Placement of a Sun Product
Caution – Do not block or cover the openings
of your Sun product. Never place a Sun
product near a radiator or heat register.
Failure to follow these guidelines can cause
overheating and affect the reliability of your
Sun product.
Symbols
The following symbols may appear in this book:
Caution – There is a risk of personal injury
and equipment damage. Follow the
instructions.
Noise Level
Declared noise emissions in accordance with ISO 9296,
A-weighted, operating and idling:
Caution – Hot surface. Avoid contact.
Surfaces are hot and may cause personal
injury if touched.
Measure and Environment
L
(1B = 10 dB)
wAd
Caution – Hazardous voltages are present. To
reduce the risk of electric shock and danger to
personal health, follow the instructions.
at or below 25ºC
at max ambient
8.0 B
8.4 B
L
bystander
pAm
at or below 25ºC
at max ambient
66 dB
69 dB
SELV Compliance
Safety status of I/O connections comply to SELV
requirements.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Cord Connection
Caution – For products with multiple power
cords, all power cords must be disconnected
to completely remove power from the system.
Caution – Sun products are designed to work
with power systems having a grounded
neutral (grounded return for DC-powered
products). To reduce the risk of electric shock,
do not plug Sun products into any other type
of power system. Contact your facilities
manager or a qualified electrician if you are
not sure what type of power is supplied to
your building.
Battery Warning
Caution – There is danger of explosion if
batteries are mishandled or incorrectly
replaced. On systems with replaceable
batteries, replace only with the same
manufacturer and type or equivalent type
recommended by the manufacturer per the
instructions provided in the product service
manual. Do not disassemble batteries or
attempt to recharge them outside the system.
Do not dispose of batteries in fire. Dispose of
batteries properly in accordance with the
manufacturer’s instructions and local
regulations. Note that on Sun CPU boards,
there is a lithium battery molded into the real-
time clock. These batteries are not customer
replaceable parts.
Caution – Not all power cords have the same
current ratings. Do not use the power cord
provided with your equipment for any other
products or use. Household extension cords
do not have overload protection and are not
meant for use with computer systems. Do not
use household extension cords with your Sun
product.
System Unit Cover
You must remove the cover of your Sun computer system
unit to add cards, memory, or internal storage devices. Be
sure to replace the cover before powering on your computer
system.
The following caution applies only to devices with a
Standby power switch:
Caution – Do not operate Sun products
without the cover in place. Failure to take this
precaution may result in personal injury and
system damage.
Caution – The power switch of this product
functions as a standby type device only. The
power cord serves as the primary disconnect
device for the system. Be sure to plug the
power cord into a grounded power outlet that
is nearby the system and is readily accessible.
Do not connect the power cord when the
power supply has been removed from the
system chassis.
The following caution applies only to devices with multiple
power cords:
36
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack System Warning
CD and DVD Devices
The following warnings apply to Racks and Rack Mounted
The following caution applies to CD, DVD, and other
systems.
optical devices.
Caution – For safety, equipment should
always be loaded from the bottom up. That is,
install the equipment that will be mounted in
the lowest part of the rack first, then the next
higher systems, etc.
Caution – Use of controls, adjustments, or
the performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
Conformité aux normes de sécurité
Caution – To prevent the rack from tipping
during equipment installation, the anti-tilt bar
on the rack must be deployed.
Veuillez lire attentivement cette section avant de
commencer. Ce texte traite des mesures de sécurité qu’il
convient de prendre pour l’installation d’un produit Sun
Microsystems.
Caution – To prevent extreme operating
temperature within the rack insure that the
maximum temperature does not exceed the
product’s ambient rated temperatures.
Mesures de sécurité
Pour votre sécurité, nous vous recommandons de suivre
scrupuleusement les mesures de sécurité ci-dessous lorsque
vous installez votre matériel:
■
Suivez tous les avertissements et toutes les
instructions inscrites sur le matériel.
Caution – To prevent extreme operating
temperatures due to reduced airflow
consideration should be made to the amount
of air flow that is required for a safe operation
of the equipment.
■
Assurez-vous que la tension et la fréquence de votre
source d'alimentation correspondent à la tension et à
la fréquence indiquées sur l'étiquette de la tension
électrique nominale du matériel
■
N'introduisez jamais d'objets quels qu'ils soient dans
les ouvertures de l'équipement. Vous pourriez vous
trouver en présence de hautes tensions dangereuses.
Tout objet étranger conducteur risque de produire un
court-circuit pouvant présenter un risque d'incendie
ou de décharge électrique, ou susceptible
Laser Compliance Notice
Sun products that use laser technology comply with Class 1
laser requirements.
d'endommager le matériel.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Safety Agency Compliance Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Symboles
Positionnement d’un produit Sun
Vous trouverez ci-dessous la signification des différents
symboles utilisés:
Attention – Evitez d'obstruer ou de recouvrir
les orifices de votre produit Sun. N'installez
jamais un produit Sun près d'un radiateur ou
d'une source de chaleur. Si vous ne respectez
pas ces consignes, votre produit Sun risque de
surchauffer et son fonctionnement en sera
altéré.
Attention – Vous risquez d'endommager le
matériel ou de vous blesser. Veuillez suivre les
instructions.
Attention – Surfaces brûlantes. Evitez tout
contact. Les surfaces sont brûlantes. Vous
risquez de vous blesser si vous les touchez.
Niveau de pression acoustique
Valeurs déclarées d'émission acoustique en conformité avec
la norme ISO 9296, Pondéré A, en fonctionnement et inactif:
Attention – Tensions dangereuses. Pour
réduire les risques de décharge électrique et
de danger physique, observez les consignes
indiquées.
Mesure et environnement
L
(1B = 10 dB)
wAd
à ou en dessous de 25ºC 8.0 B
à temp. ambiante maxi. 8.4 B
assistant
Selon le type d'interrupteur marche/arrêt dont votre
appareil est équipé, l'un des symboles suivants sera utilisé:
L
pAm
Marche – Met le système sous tension
alternative.
à ou en dessous de 25ºC 66 dB
à temp. ambiante maxi. 69 dB
Arret – Met le système hors tension
alternative.
Conformité SELV
Le niveau de sécurité des connexions E/S est conforme aux
normes SELV.
Veilleuse – L'interrupteur Marche/Veille est
sur la position de veille.
Connexion du cordon d’alimentation
Attention – Les produits Sun sont conçus
pour fonctionner avec des systèmes
d'alimentation équipés d'un conducteur
neutre relié à la terre (conducteur neutre pour
produits alimentés en CC). Pour réduire les
risques de décharge électrique, ne branchez
jamais les produits Sun sur une source
d'alimentation d'un autre type. Contactez le
gérant de votre bâtiment ou un électricien
agréé si vous avez le moindre doute quant au
type d'alimentation fourni dans votre
bâtiment.
Modification du matériel
N'apportez aucune modification mécanique ou électrique
au matériel. Sun Microsystems décline toute responsabilité
quant à la non-conformité éventuelle d'un produit Sun
modifié.
38
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Mise en garde relative aux batteries
Attention – Tous les cordons d'alimentation
ne présentent pas les mêmes caractéristiques
électriques. Les cordons d'alimentation à
usage domestique ne sont pas protégés contre
les surtensions et ne sont pas conçus pour être
utilisés avec des ordinateurs. N'utilisez jamais
de cordon d'alimentation à usage domestique
avec les produits Sun.
Attention – Les batteries risquent d’exploser
en cas de manipulation maladroite ou de
remplacement incorrect. Pour les systèmes
dont les batteries sont remplaçables, effectuez
les remplacements uniquement selon le
modèle du fabricant ou un modèle équivalent
recommandé par le fabricant, conformément
aux instructions fournies dans le manuel de
service du système. N’essayez en aucun cas de
démonter les batteries, ni de les recharger hors
du système. Ne les jetez pas au feu. Mettez-les
au rebut selon les instructions du fabricant et
conformément à la législation locale en
L'avertissement suivant s'applique uniquement aux
systèmes équipés d'un interrupteur Veille:
Attention – L'interrupteur d'alimentation de
ce produit fonctionne uniquement comme un
dispositif de mise en veille. Le cordon
d'alimentation constitue le moyen principal de
déconnexion de l'alimentation pour le
système. Assurez-vous de le brancher dans
une prise d'alimentation mise à la terre près
du système et facile d'accès. Ne le branchez
pas lorsque l'alimentation électrique ne se
trouve pas dans le châssis du système.
vigueur. Notez que sur les cartes processeur
de Sun, une batterie au lithium a été moulée
dans l'horloge temps réel. Les batteries ne sont
pas des pièces remplaçables par le client.
Couvercle de l'unité
Pour ajouter des cartes, de la mémoire ou des périphériques
de stockage internes, vous devez retirer le couvercle de
votre système Sun. Remettez le couvercle supérieur en
place avant de mettre votre système sous tension.
L'avertissement suivant s'applique uniquement aux
systèmes équipés de plusieurs cordons d'alimentation:
Attention – Pour mettre un système équipé
de plusieurs cordons d'alimentation hors
tension, il est nécessaire de débrancher tous
les cordons d'alimentation.
Attention – Ne mettez jamais des produits
Sun sous tension si leur couvercle supérieur
n'est pas mis en place. Si vous ne prenez pas
ces précautions, vous risquez de vous blesser
ou d'endommager le système.
Mise en garde relative au système en rack
La mise en garde suivante s'applique aux racks et aux
systèmes montés en rack.
Attention – Pour des raisons de sécurité, le
matériel doit toujours être chargé du bas vers
le haut. En d'autres termes, vous devez
installer, en premier, le matériel qui doit se
trouver dans la partie la plus inférieure du
rack, puis installer le matériel sur le niveau
suivant, etc.
Safety Agency Compliance Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Einhaltung sicherheitsbehördlicher
Vorschriften
Lesen Sie vor dem Ausführen von Arbeiten diesen
Abschnitt. Im folgenden Text werden Sicherheitsvor-
kehrungen beschrieben, die Sie bei der Installation eines
Sun Microsystems-Produkts beachten müssen.
Attention – Afin d'éviter que le rack ne
penche pendant l'installation du matériel, tirez
la barre anti-basculement du rack.
Attention – Pour éviter des températures de
fonctionnement extrêmes dans le rack,
assurez-vous que la température maximale ne
dépasse pas la fourchette de températures
ambiantes du produit déterminée par le
fabricant.
Sicherheitsvorkehrungen
Treffen Sie zu Ihrem eigenen Schutz bei der Installation des
Geräts die folgenden Sicherheitsvorkehrungen:
■
■
Beachten Sie alle auf den Geräten angebrachten
Warnhinweise und Anweisungen.
Stellen Sie sicher, dass Spannung und Frequenz der
Stromversorgung den Nennleistungen auf dem am
Gerät angebrachten Etikett entsprechen.
Attention – Afin d'empêcher des
températures de fonctionnement extrêmes
provoquées par une aération insuffisante,
assurez-vous de fournir une aération
appropriée pour un fonctionnement du
matériel en toute sécurité
■
Führen Sie niemals Fremdobjekte in die Öffnungen
am Gerät ein. Es können gefährliche Spannungen
anliegen. Leitfähige Fremdobjekte können einen
Kurzschluss verursachen, der einen Brand, Strom-
schlag oder Geräteschaden herbeiführen kann.
Avis de conformité des appareils laser
Les produits Sun qui font appel aux technologies lasers sont
conformes aux normes de la classe 1 en la matière.
Symbole
Die Symbole in diesem Handbuch haben folgende
Bedeutung:
Achtung – Gefahr von Verletzung und
Geräteschaden. Befolgen Sie die Anwei-
sungen.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Achtung – Heiße Oberfläche. Nicht berühren,
da Verletzungsgefahr durch heiße Oberfläche
besteht.
Périphériques CD et DVD
L'avertissement suivant s'applique aux périphériques CD,
DVD et autres périphériques optiques:
Achtung – Gefährliche Spannungen.
Befolgen Sie die Anweisungen, um
Stromschläge und Verletzungen zu vermeiden.
Attention – L'utilisation de contrôles et de
réglages ou l'application de procédures autres
que ceux spécifiés dans le présent document
peuvent entraîner une exposition à des
radiations dangereuses.
40
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Je nach Netzschaltertyp an Ihrem Gerät kann eines der
folgenden Symbole verwendet werden:
Lautstärke
Angegebene Geräuschentwicklung im Einklang mit ISO
9296, A-bewertet, in Betrieb und im Ruhezustand:
Ein – Versorgt das System mit Wechselstrom.
Messwert und Umgebung
L
(1B = 10 dB)
wAd
Aus– Unterbricht die Wechselstromzufuhr
zum Gerät.
bei oder unter 25ºC
bei max. Umgebung
8.0 B
8.4 B
Wartezustand – Der Ein-/Standby-Netz-
L
Umstehende
pAm
schalter befindet sich in der Standby-Position.
bei oder unter 25ºC
bei max. Umgebung
66 dB
69 dB
Modifikationen des Geräts
Nehmen Sie keine elektrischen oder mechanischen
Gerätemodifikationen vor. Sun Microsystems ist für die
Einhaltung der Sicherheitsvorschriften von modifizierten
Sun-Produkten nicht haftbar.
SELV-Konformität
Der Sicherheitsstatus der E/A-Verbindungen entspricht
den SELV-Anforderungen.
Anschluss des Netzkabels
Aufstellung von Sun-Geräten
Achtung – Sun-Geräte sind für
Achtung – Geräteöffnungen Ihres Sun-
Produkts dürfen nicht blockiert oder
Stromversorgungssysteme mit einem
geerdeten neutralen Leiter (geerdeter
Rückleiter bei gleichstrombetriebenen
Geräten) ausgelegt. Um die Gefahr von
Stromschlägen zu vermeiden, schließen Sie
das Gerät niemals an andere Stromversor-
gungssysteme an. Wenden Sie sich an den
zuständigen Gebäudeverwalter oder an einen
qualifizierten Elektriker, wenn Sie nicht sicher
wissen, an welche Art von Stromversor-
gungssystem Ihr Gebäude angeschlossen ist.
abgedeckt werden. Sun-Geräte sollten niemals
in der Nähe von Heizkörpern oder Heißluft-
klappen aufgestellt werden. Die Nichtbeach-
tung dieser Richtlinien kann Überhitzung
verursachen und die Zuverlässigkeit Ihres
Sun-Geräts beeinträchtigen.
Achtung – Nicht alle Netzkabel verfügen
über die gleichen Nennwerte. Herkömmliche,
im Haushalt verwendete Verlängerungskabel
besitzen keinen Überlastschutz und sind
daher für Computersysteme nicht geeignet.
Verwenden Sie bei Ihrem Sun-Produkt keine
Haushalts-Verlängerungskabel.
Safety Agency Compliance Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Die folgende Warnung gilt nur für Geräte mit Standby-
Netzschalter:
Gehäuseabdeckung
Sie müssen die Abdeckung Ihres Sun-Computersystems
entfernen, um Karten, Speicher oder interne Speichergeräte
hinzuzufügen. Bringen Sie vor dem Einschalten des
Systems die Gehäuseabdeckung wieder an.
Achtung – Beim Netzschalter dieses Geräts
handelt es sich nur um einen Ein/Standby-
Schalter. Zum völligen Abtrennen des Systems
von der Stromversorgung dient hauptsächlich
das Netzkabel. Stellen Sie sicher, dass das
Netzkabel an eine frei zugängliche geerdete
Steckdose in der Nähe des Systems ange-
schlossen ist. Schließen Sie das Stromkabel
nicht an, wenn die Stromversorgung vom
Systemchassis entfernt wurde.
Achtung – Nehmen Sie Sun-Geräte nicht
ohne Abdeckung in Betrieb. Die
Nichtbeachtung dieses Warnhinweises kann
Verletzungen oder Geräteschaden zur Folge
haben.
Warnungen bezüglich in Racks eingebauter
Systeme
Die folgenden Warnungen gelten für Racks und in Racks
Die folgende Warnung gilt nur für Geräte mit mehreren
Netzkabeln:
eingebaute Systeme:
Achtung – Bei Produkten mit mehreren
Netz-kabeln müssen alle Netzkabel abgetrennt
wer-den, um das System völlig von der
Stromver-sorgung zu trennen.
Achtung – Aus Sicherheitsgründen sollten
sämtliche Geräte von unten nach oben in
Racks eingebaut werden. Installieren Sie also
zuerst die Geräte, die an der untersten
Position im Rack eingebaut werden, gefolgt
von den Systemen, die an nächsthöherer Stelle
eingebaut werden, usw.
Warnung bezüglich Batterien
Achtung – Bei unsachgemäßer Handhabung
oder nicht fachgerechtem Austausch der
Batterien besteht Explosionsgefahr. Verwen-
den Sie bei Systemen mit austauschbaren
Batterien ausschließlich Ersatzbatterien
desselben Typs und Herstellers bzw. einen
entsprechenden, vom Hersteller gemäß den
Anweisungen im Service-Handbuch des
Produkts empfohlenen Batterietyp. Versuchen
Sie nicht, die Batterien auszubauen oder
außerhalb des Systems wiederaufzuladen.
Werfen Sie die Batterien nicht ins Feuer.
Entsorgen Sie die Batterien entsprechend den
Anweisungen des Herstellers und den vor Ort
geltenden Vorschriften. CPU-Karten von Sun
verfügen über eine Echtzeituhr mit integrier-
ter Lithiumbatterie. Diese Batterie darf nur
von einem qualifizierten Servicetechniker aus-
gewechselt werden.
Achtung – Verwenden Sie beim Einbau den
Kippschutz am Rack, um ein Umkippen zu
vermeiden.
Achtung – Um extreme
Betriebstemperaturen im Rack zu vermeiden,
stellen Sie sicher, dass die Maximaltemperatur
die Nennleistung der Umgebungstemperatur
für das Produkt nicht überschreitet
Achtung – Um extreme
Betriebstemperaturen durch verringerte
Luftzirkulation zu vermei-den, sollte die für
den sicheren Betrieb des Geräts erforderliche
Luftzirkulation eingesetzt werden.
42
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Hinweis zur Laser-Konformität
Sun-Produkte, die die Laser-Technologie verwenden,
entsprechen den Laser-Anforderungen der Klasse 1.
Precaución – Existe el riesgo de que se
produzcan lesiones personales y daños en el
equipo. Siga las instrucciones.
Precaución – Superficie caliente. Evite todo
contacto. Las superficies están calientes y
pueden causar lesiones personales si se tocan.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Precaución – Voltaje peligroso. Para reducir
el riesgo de descargas eléctricas y lesiones
personales, siga las instrucciones.
CD- und DVD-Geräte
Die folgende Warnung gilt für CD-, DVD- und andere
optische Geräte:
En función del tipo de interruptor de alimentación del que
disponga el dispositivo, se utilizará uno de los símbolos
siguientes:
Achtung – Die hier nicht aufgeführte
Verwendung von Steuerelementen,
Anpassungen oder Ausführung von
Vorgängen kann eine gefährliche
Strahlenbelastung verursachen.
Encendido – Suministra alimentación de CA
al sistema.
Apagado – Corta la alimentación de CA del
sistema.
Normativas de seguridad
Lea esta sección antes de realizar cualquier operación. En
ella se explican las medidas de seguridad que debe tomar al
instalar un producto de Sun Microsystems.
Espera – El interruptor de encendido/espera
está en la posición de espera.
Medidas de seguridad
Para su protección, tome las medidas de seguridad
siguientes durante la instalación del equipo:
Modificaciones en el equipo
No realice modificaciones de tipo mecánico ni eléctrico en el
equipo. Sun Microsystems no se hace responsable del
cumplimiento de normativas en caso de que un producto
Sun se haya modificado.
■
■
Siga todos los avisos e instrucciones indicados en el
equipo.
Asegúrese de que el voltaje y frecuencia de la fuente
de alimentación coincidan con el voltaje y frecuencia
indicados en la etiqueta de clasificación eléctrica del
equipo.
Colocación de un producto Sun
Precaución – No obstruya ni tape las rejillas
del producto Sun. Nunca coloque un producto
Sun cerca de radiadores ni fuentes de calor. Si
no sigue estas indicaciones, el producto Sun
podría sobrecalentarse y la fiabilidad de su
funcionamiento se vería afectada.
■
No introduzca objetos de ningún tipo por las rejillas
del equipo, ya que puede quedar expuesto a voltajes
peligrosos. Los objetos conductores extraños pueden
producir cortocircuitos y, en consecuencia, incendios,
descargas eléctricas o daños en el equipo.
Símbolos
En este documento aparecen los siguientes símbolos:
Safety Agency Compliance Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
43
La siguiente medida solamente se aplica a aquellos
dispositivos que dispongan de un interruptor de
alimentación de espera:
Nivel de ruido
Emisiones acústicas declaradas de acuerdo con la norma
ISO 9296 (decibelios A), en funcionamiento y reposo:
Precaución – El interruptor de alimentación
de este producto funciona solamente como un
dispositivo de espera. El cable de alimentación
hace las veces de dispositivo de desconexión
principal del sistema. Asegúrese de que
conecta el cable de alimentación a una toma
de tierra situada cerca del sistema y de fácil
acceso. No conecte el cable de alimentación si
la unidad de alimentación no se encuentra en
el bastidor del sistema.
Medición y condiciones ambientales
L
(1B = 10 dB)
wAd
a 25ºC o menos:
8.0 B
8.4 B
máxima temp. ambiente:
L
(posición de observación)
pAm
a 25ºC o menos:
66 dB
69 dB
máxima temp. ambiente:
La siguiente medida solamente se aplica a aquellos
dispositivos que dispongan de varios cables de
alimentación:
Cumplimiento de la normativa para
instalaciones SELV
Las condiciones de seguridad de las conexiones de entrada
y salida cumplen los requisitos para instalaciones SELV (del
inglés Safe Extra Low Voltage, voltaje bajo y seguro).
Precaución – En los productos que cuentan
con varios cables de alimentación, debe
desconectar todos los cables de alimentación
para cortar por completo la alimentación
eléctrica del sistema.
Conexión del cable de alimentación
Precaución – Los productos Sun se han
diseñado para funcionar con sistemas de
alimentación que cuenten con un conductor
neutro a tierra (con conexión a tierra de
regreso para los productos con alimentación
de CC). Para reducir el riesgo de descargas
eléctricas, no conecte ningún producto Sun a
otro tipo de sistema de alimentación. Póngase
en contacto con el encargado de las
instalaciones de su empresa o con un
electricista cualificado en caso de que no esté
seguro del tipo de alimentación del que se
dispone en el edificio.
Advertencia sobre las baterías
Precaución – Si las baterías no se manipulan
o reemplazan correctamente, se corre el riesgo
de que estallen. En los sistemas que cuentan
con baterías reemplazables, reemplácelas sólo
con baterías del mismo fabricante y el mismo
tipo, o un tipo equivalente recomendado por
el fabricante, de acuerdo con las instrucciones
descritas en el manual de servicio del
producto. No desmonte las baterías ni intente
recargarlas fuera del sistema. No intente
deshacerse de las baterías echándolas al fuego.
Deshágase de las baterías correctamente de
acuerdo con las instrucciones del fabricante y
las normas locales. Tenga en cuenta que en las
placas CPU de Sun, hay una batería de litio
incorporada en el reloj en tiempo real. Los
usuarios no deben reemplazar este tipo de
baterías.
Precaución – No todos los cables de
alimentación tienen la misma clasificación
eléctrica. Los alargadores de uso doméstico no
cuentan con protección frente a sobrecargas y
no están diseñados para su utilización con
sistemas informáticos. No utilice alargadores
de uso doméstico con el producto Sun.
44
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Cubierta de la unidad del sistema
Aviso de cumplimiento de la normativa para
la utilización de láser
Los productos Sun que utilizan tecnología láser cumplen los
Debe extraer la cubierta de la unidad del sistema
informático Sun para instalar tarjetas, memoria o
dispositivos de almacenamiento internos. Vuelva a colocar
la cubierta antes de encender el sistema informático.
requisitos establecidos para los productos láser de clase 1.
Precaución – No ponga en funcionamiento
los productos Sun que no tengan colocada la
cubierta. De lo contrario, puede sufrir lesiones
personales y ocasionar daños en el sistema.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
Advertencia sobre el sistema en bastidor
Las advertencias siguientes se aplican a los sistemas
montados en bastidor y a los propios bastidores.
Dispositivos de CD y DVD
La siguiente medida se aplica a los dispositivos de CD y
DVD, así como a otros dispositivos ópticos:
Precaución – Por seguridad, siempre deben
montarse los equipos de abajo arriba. A saber,
primero debe instalarse el equipo que se
situará en el bastidor inferior; a continuación,
el que se situará en el siguiente nivel, etc.
Precaución – La utilización de controles,
ajustes o procedimientos distintos a los aquí
especificados puede dar lugar a niveles de
radiación peligrosos.
Precaución – Para evitar que el bastidor se
vuelque durante la instalación del equipo,
debe extenderse la barra antivolcado del
bastidor.
Nordic Lithium Battery Cautions
Norge
Precaución – Para evitar que se alcance una
temperatura de funcionamiento extrema en el
bastidor, asegúrese de que la temperatura
máxima no sea superior a la temperatura
ambiente establecida como adecuada para el
producto.
Advarsel – Litiumbatteri — Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten. Brukt batteri
returneres apparatleverandøren.
Sverige
Precaución – Para evitar que se alcance una
temperatura de funcionamiento extrema
debido a una circulación de aire reducida,
debe considerarse la magnitud de la
circulación de aire requerida para que el
equipo funcione de forma segura.
Varning – Explosionsfara vid felaktigt
batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av
apparattillverkaren. Kassera använt batteri
enligt fabrikantens instruktion.
Safety Agency Compliance Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Danmark
Advarsel! – Litiumbatteri — Eksplosionsfare
ved fejlagtig håndtering. Udskiftning må kun
ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til
leverandøren.
Suomi
Varoitus – Paristo voi räjähtää, jos se on
virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
46
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance Statements
Your Sun product is marked to indicate its compliance class:
•
•
•
Federal Communications Commission (FCC) — USA
Industry Canada Equipment Standard for Digital Equipment (ICES-003) — Canada
Bureau of Standards Metrology and Inspection (BSMI) — Taiwan
Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the
product.
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required
to correct the interference at his own expense.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority
granted to the user by the FCC to operate this equipment.
ICES-003 Class A Notice - Avis NMB-003, Classe A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
BSMI Class A Notice
The following statement is applicable to products shipped to Taiwan and marked as Class A on the product compliance
label.
D33728
48
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
CCC Class A Notice
The following statement is applicable to products shipped to China and marked with “Class A” on the product’s compliance
label.
Korean MIC Class A Statement
Regulatory Compliance Statements
Download from Www.Somanuals.com. All Manuals Search And Download.
49
50
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
F
firmware
B
update, 26
C
chassis monitoring module (CMM)
firmware, 5
HBA drivers
known issues, 30
compliance statements
connecting links to blades status
status
I
feature, 3
patch, 19
replace, 20
external FC, 2
NEM port, 9
ILOM
D
diagnostics, 26
L
E
LEDs
electrostatic discharge (ESD) handling
precautions, 8
NEM, 18
port, 13
ESD wrist strap, 8
lights-out management (ILOM) interface, 14
link rate, 13
51
Download from Www.Somanuals.com. All Manuals Search And Download.
links connected to blades status, 18
Linux
S
safety precautions, 35
supported versions, 4
Locator LED and button, 18
LUNs, discover, 26
Small Form-Factor Pluggable (SFP), 2
M
memory, 2
port LED definitions, 13
Sun StorEdge 3510/3511 RAID arrays, 29
N
NEM
interface, 2
LED status, 18
part number, 2
O
operating systems
supported, 5
W
operating systems, supported versions, 4
Windows 2003 OS
driver, 26
supported versions, 4
P
patches
port LEDs, 13
port numbering, 11
power-on self tests
BIOS, 30
NEM, 12
R
ready to remove status, 18
regulatory compliance statements, 47
Restriction of Hazardous Substances (RoHS)
directive, 33
52
Sun StorageTek 4 Gb FC NEM 20-Port Host Bus Adapter User’s Guide • February 2008
Download from Www.Somanuals.com. All Manuals Search And Download.
|