5" x 6" HORIZONTAL/VERTICAL
BANDSAW
MODEL SB1017
OWNER'S MANUAL
Hundreds of Thousands of Lathes Sold With a Tradition of
Q
uality Since 1906!
Copyright © May, 2010 Revised February, 2011 (JB)
For Machines Mfg. Since 8/09
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION...............................................................2
Blade Tension.....................................................25
Blade Breakage..................................................25
Blade Care & Break-In......................................26
Blade Care ........................................................26
Blade Break-In..................................................26
Blade Speed........................................................26
Blade Speed Chart.............................................27
Chip Inspection Chart .......................................27
Downfeed Pressure ............................................28
Downfeed Rate...................................................28
Work Stop...........................................................28
Vise .....................................................................29
Blade Guide........................................................30
Vertical Cutting .................................................30
Operation Tips ...................................................31
Horizontal Cutting.............................................31
Vertical Cutting.................................................31
About This Machine.............................................2
Capabilities.........................................................2
Features..............................................................2
Identification........................................................3
Machine Specifications ........................................4
SAFETY................................................................................6
Understanding Risks of Machinery ....................6
Basic Machine Safety ..........................................6
Additional Metal Bandsaw Safety ......................8
PREPARATION .................................................................9
Preparation Overview..........................................9
Required for Setup...............................................9
Power Supply Requirements...............................9
Availability..........................................................9
Full-Load Current Rating ....................................9
Circuit Information............................................10
Circuit Requirements for 110V...........................10
Circuit Requirements for 220V...........................10
ACCESSORIES..............................................................32
Accessories .........................................................32
Grounding Requirements...................................10 MAINTENANCE .............................................................33
Extension Cords ................................................11
Unpacking ..........................................................12
Inventory............................................................12
Assembly ............................................................13
Cleaning & Protecting .......................................16
Location..............................................................17
Physical Environment........................................17
Electrical Installation ........................................17
Lighting ............................................................17
Weight Load......................................................17
Space Allocation ................................................17
Power Connection ..............................................18
Test Run.............................................................18
Inspections & Adjustments ...............................18
Maintenance Schedule.......................................33
Cleaning .............................................................33
Lubrication.........................................................33
Gearbox.............................................................33
V-Belt Replacement...........................................34
Machine Storage ................................................34
Downfeed Stop Bolt ...........................................35
Blade Tracking...................................................35
Blade Guide Bearings........................................36
Squaring Blade ..................................................37
Auto-OFF Tab ....................................................37
TROUBLESHOOTING.................................................38
ELECTRICAL...................................................................41
Electrical Safety Instructions ...........................41
220V Conversion................................................42
Wiring Diagram .................................................43
OPERATION....................................................................19
Operation Overview...........................................19
Controls ..............................................................20
Blade Selection...................................................21
Blade Terminology.............................................21
Blade Length.....................................................21
Blade Width ......................................................21
Tooth Set...........................................................22
Tooth Type ........................................................22
Blade Pitch (TPI)...............................................23
Blade Changes ...................................................24
PARTS................................................................................44
Table...................................................................44
Cabinet Stand ....................................................45
Head ...................................................................46
Motor & Blade Guides .......................................48
Switch.................................................................50
Machine Labels..................................................51
WARRANTY & RETURNS..........................................53
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
I N T R O D U C T I O N
INTRODUCTION
About This Machine
Capabilities
Features
This metal cutting bandsaw uses a gravity-fed
blade to make straight cuts through workpieces
that are clamped in a vise. Since the workpiece is
secured and remains stationary while the blade
feeds automatically, accuracy and operator safety
are maximized.
In addition to its capabilities, the Model SB1017
has several features to increase versatility and
efficiency.
The vise can be rotated to perform angled cuts up
to 45° while three blade speeds ensure that the
proper cutting rate is available for a variety of
workpiece sizes and materials.
The vise on the Model SB1017 is capable of
holding rectangular stock up to 5" x 6" and round
stock up to 5".
Both the downfeed rate and pressure are
adjustable for fine-tuning each cutting operation
and an adjustable auto-OFF power switch
maximizes safety and minimizes energy use by
turning the machine off at the end of every cut.
After a cut is complete, the OFF switch is
triggered and the motor automatically turns off.
A storage compartment in the cabinet base
provides a convenient location for keeping spare
blades or other accessories and the transport
handle makes moving the machine easy.
Finally, the cast-aluminum knobs and belt cover
proudly bear the legendary South Bend name.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
I N T R O D U C T I O N
Identification
Blade Tension
Guide Post
Knob
Belt Cover
Motor
Knob
Blade
Downfeed
Rate Adjust
Knob
Switch
Auto-Off
Tab
Downfeed
Ram
ON/OFF
Switch
Feed
Pressure
Handle
Downfeed
Stop Bolt
Vise
Jaw
Vise Jaw
Handwheel
Work Stop
Front View
Head
Locking Pin
Transport
Handle
Rear View
Leveling Foot
Cabinet Access
Door
Figure 1. Identification.
Serious personal injury could occur if
you connect the machine to power before
completing the setup process. DO NOT
connect power until instructed to do so later
in this manual.
Untrained users have an increased risk
of seriously injuring themselves with this
machine. Do not operate this machine until
you have understood this entire manual and
received proper training.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
I N T R O D U C T I O N
Machine Specifications
P.O. Box 2027, Bellingham, WA 98227 U.S.A.
PHONE: (360) 734-1540 • © South Bend Lathe Co.
Model SB1017
5" x 6" Horizontal/Vertical Bandsaw
Product Dimensions:
Weight ..........................................................................................................................................................................166 lbs.
Length/Width/Height ............................................................................................................................. 383⁄4" x 173⁄4" x 391⁄2
"
"
Foot Print (Length/Width) ...................................................................................................................................383⁄4" x 173⁄4
Space Required for Full Range of Movement (Length/Width/Height).......................................................... 80" x 55" x 78"
Shipping Dimensions:
Machine
Type ...................................................................................................................................................................... Carton
Weight..................................................................................................................................................................170 lbs.
Length/Width/Height.............................................................................................................................. 42" x 17" x 16"
Stand
Type ...................................................................................................................................................................... Carton
Weight....................................................................................................................................................................47 lbs.
Length/Width/Height.............................................................................................................................. 17" x 13" x 23"
Electrical:
Required Power Source.......................................................................................................110V/220V, Single-Phase, 60 Hz
Switch..................................................................................................................................................Toggle ON/OFF Switch
Switch Voltage.................................................................................................................................................................. 110V
Cord Length........................................................................................................................................................................6 ft.
Cord Gauge .................................................................................................................................................................18 gauge
Recommended Circuit Size ..........................................................................................................................................15 Amp
Plug Included.......................................................................................................................................................................Yes
Motors:
Main
Type ............................................................................................................................TEFC Capacitor Start Induction
Horsepower............................................................................................................................................................. 1⁄2 HP
Voltage............................................................................................................................................................110V/220V
Phase ..........................................................................................................................................................Single-Phase
Amps................................................................................................................................................................... 8.6/4.3A
Speed............................................................................................................................................................... 1725 RPM
Cycle .......................................................................................................................................................................60 Hz
Number Of Speeds.........................................................................................................................................................1
Pre-Wired ................................................................................................................................................................ 110V
Power Transfer.........................................................................................................................................V-Belt & Gear
Bearings...................................................................................................................Shielded and Permanently Sealed
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
I N T R O D U C T I O N
Main Specifications:
Operation Information
Head Swivel..........................................................................................................................................................45 deg.
Blade Speeds ...................................................................................................................................... 80, 120, 200 FPM
Std. Blade Length....................................................................................................................................................641⁄2
Blade Size Range .........................................................................................................................................................1⁄2
"
"
Cutting Capacities
Angle Cuts............................................................................................................................................................45 deg.
Vise Jaw Depth......................................................................................................................................................... 65⁄8
"
"
Vise Jaw Height........................................................................................................................................................ 25⁄8
Max. Capacity Rect. Height At 90D ........................................................................................................................... 5"
Max. Capacity Rect. Width At 90D ............................................................................................................................ 6"
Max. Capacity Rnd. At 90D ........................................................................................................................................ 5"
Max. Capacity Rect. Height At 45D ........................................................................................................................... 3"
Max. Capacity Rect. Width At 45D ......................................................................................................................... 41⁄2
"
Max. Capacity Rnd. At 45D ........................................................................................................................................ 3"
Construction
Wheel Construction Upper..............................................................................................................................Cast Iron
Wheel Construction Lower..............................................................................................................................Cast Iron
Body Construction ...........................................................................................................................................Cast Iron
Base Construction............................................................................................................................................Cast Iron
Stand Construction................................................................................................................................................. Steel
Tire Material.......................................................................................................................................Rubber and Steel
Other
Wheel Size.................................................................................................................................................................... 5"
Blade Guides Upper...................................................................................................................................................Yes
Blade Guides Lower...................................................................................................................................................Yes
Table Info
Floor to Cutting Area Height................................................................................................................................. 251⁄2
"
Other Specifications:
ISO Factory................................................................................................................................................................ ISO 9001
Country Of Origin ........................................................................................................................................................ Taiwan
Warranty.........................................................................................................................................................................1 Year
Serial Number Location.................................................................................................................. ID Label on Body Frame
Customer Setup and Cleaning Time.................................................................................................. Approximately 1 Hour
Features:
Heavy-Duty One-Piece Steel Stand
Conveniently Located ON/OFF Toggle Switch
Adjustable Hydraulic Down Feed
Cast Iron Handwheel with Chromed Handle
Die Cast South Bend Star Knobs
Die Cast South Bend Belt Guard
Built-In Storage Cabinet
Leveling Feet and Wheels to Ease Mobility
Work Stop for Horizontal Cuts
Satin Chromed Handle Bar
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
S A F E T Y
SAFETY
Understanding Risks of Machinery
Operating all machinery and machining equipment can be dangerous or relatively safe depending
on how it is installed and maintained, and the operator's experience, common sense, risk awareness,
working conditions, and use of personal protective equipment (safety glasses, respirators, etc.).
The owner of this machinery or equipment is ultimately responsible for its safe use. This
responsibility includes proper installation in a safe environment, personnel training and usage
authorization, regular inspection and maintenance, manual availability and comprehension,
application of safety devices, integrity of cutting tools or accessories, and the usage of approved
personal protective equipment by all operators and bystanders.
The manufacturer of this machinery or equipment will not be held liable for injury or property
damage from negligence, improper training, machine modifications, or misuse. Failure to read,
understand, and follow the manual and safety labels may result in serious personal injury, including
amputation, broken bones, electrocution, or death.
The signals used in this manual to identify hazard levels are defined as follows:
Death or catastrophic
harm WILL occur.
Moderate injury or fire
MAY occur.
Death or catastrophic
harm COULD occur.
Machine or property
damage may occur.
Basic Machine Safety
1. Owner’s Manual: All machinery and
machining equipment presents serious
injury hazards to untrained users. To
reduce the risk of injury, anyone who uses
THIS item MUST read and understand
this entire manual before starting.
3. Trained/Supervised Operators Only:
Untrained users can seriously injure
themselves or bystanders. Only allow
trained and properly supervised personnel
to operate this item. Make sure safe
operation instructions are clearly
understood. If electrically powered, use
padlocks and master switches, and remove
start switch keys to prevent unauthorized
use or accidental starting.
2. Personal Protective Equipment: Operating
or servicing this item may expose the user
to flying debris, dust, smoke, dangerous
chemicals, or loud noises. These hazards
can result in eye injury, blindness, long-
term respiratory damage, poisoning,
4. Guards/Covers: Accidental contact with
moving parts during operation may cause
severe entanglement, impact, cutting,
or crushing injuries. Reduce this risk by
keeping any included guards/covers/doors
installed, fully functional, and positioned
for maximum protection.
cancer, reproductive harm or hearing loss.
Reduce your risks from these hazards
by wearing approved eye protection,
respirator, gloves, or hearing protection.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
11. Chuck Keys or Adjusting Tools: Tools used
S A F E T Y
5. Entanglement: Loose clothing, gloves,
neckties, jewelry or long hair may
get caught in moving parts, causing
entanglement, amputation, crushing,
or strangulation. Reduce this risk by
removing/securing these items so they
cannot contact moving parts.
to adjust spindles, chucks, or any moving/
rotating parts will become dangerous
projectiles if left in place when the machine
is started. Reduce this risk by developing
the habit of always removing these tools
immediately after using them.
12. Work Area: Clutter and dark shadows
increase the risks of accidental injury.
Only operate this item in a clean, non-
glaring, and well-lighted work area.
6. Mental Alertness: Operating this item
with reduced mental alertness increases
the risk of accidental injury. Do not let a
temporary influence or distraction lead to a
permanent disability! Never operate when
under the influence of drugs/alcohol, when
tired, or otherwise distracted.
13. Properly Functioning Equipment: Poorly
maintained, damaged, or malfunctioning
equipment has higher risks of causing
serious personal injury compared to
those that are properly maintained.
To reduce this risk, always maintain
this item to the highest standards and
promptly repair/service a damaged or
malfunctioning component. Always follow
the maintenance instructions included in
this documentation.
7. Safe Environment: Operating electrically
powered equipment in a wet environment
may result in electrocution; operating near
highly flammable materials may result in a
fire or explosion. Only operate this item in
a dry location that is free from flammable
materials.
8. Electrical Connection: With electically
powered equipment, improper connections
to the power source may result in
14. Unattended Operation: Electrically
powered equipment that is left unattended
while running cannot be controlled and is
dangerous to bystanders. Always turn the
power OFF before walking away.
electrocution or fire. Always adhere to all
electrical requirements and applicable
codes when connecting to the power source.
Have all work inspected by a qualified
electrician to minimize risk.
15. Health Hazards: Certain cutting fluids
and lubricants, or dust/smoke created
when cutting, may contain chemicals
known to the State of California to cause
cancer, respiratory problems, birth defects,
or other reproductive harm. Minimize
exposure to these chemicals by wearing
approved personal protective equipment
and operating in a well ventilated area.
9. Disconnect Power: Adjusting or servicing
electrically powered equipment while it
is connected to the power source greatly
increases the risk of injury from accidental
startup. Always disconnect power
BEFORE any service or adjustments,
including changing blades or other tooling.
16. Difficult Operations: Attempting
difficult operations with which you are
unfamiliar increases the risk of injury.
If you experience difficulties performing
the intended operation, STOP! Seek an
alternative method to accomplish the
same task, ask a qualified expert how the
operation should be performed, or contact
our Technical Support for assistance.
10. Secure Workpiece/Tooling: Loose
workpieces, cutting tools, or rotating
spindles can become dangerous projectiles
if not secured or if they hit another object
during operation. Reduce the risk of this
hazard by verifying that all fastening
devices are properly secured and items
attached to spindles have enough clearance
to safely rotate.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
S A F E T Y
Additional Metal Bandsaw Safety
1. Blade Condition. A dull or damaged
blade can break apart during operation,
increasing the risk of operator injury. Do
not operate with a dull, cracked or badly
worn blade. Inspect the blade for cracks
or missing teeth before each use.
6. Workpiece Handling. A shifting workpiece
can result in impact or laceration injuries.
To reduce the risk of injury, always securely
clamp the workpiece in the vise and use
additional support fixtures if needed. Never
hold the workpiece with your hands during
a cut. Flag long pieces to reduce the risk of
tripping over them.
2. Hand Placement. Hands could be cut
by the blade or crushed when lowering
the headstock. Never position fingers or
thumbs in line with the cut or under the
headstock while it is moving.
7. Power Interruption. Unplug the machine
and turn the power switch OFF after a
power interruption. If left plugged in and
turned ON, this machine will start up when
power is restored, resulting in possible
entanglement, laceration, or amputation
hazards.
3. Blade Guard. Hands and fingers can
easily be cut by the bandsaw blade. To
reduce the risk of laceration injuries, do
not operate this bandsaw without the
blade guard in place.
8. Hot Surfaces/Sharp Edges. Due to the
cutting process, a freshly cut workpiece,
chips, and some machine components
can be hot enough to burn you and sharp
enough to cut you. Allow components to cool
and use safe handling methods to reduce
the risk of these injuries.
4. Starting Position. To reduce the
likelihood of blade breakage and possible
entanglement, never turn the saw ON
with the blade resting on the workpiece.
5. Blade Replacement. The blade can
only make a safe and efficient cut if the
teeth are facing the workpiece. When
replacing blades, make sure the teeth
face toward the workpiece. Wear gloves
to protect hands and safety glasses to
protect eyes.
9. Moving Blade. A moving bandsaw blade
presents a serious risk for laceration or
amputation injuries. Always allow the blade
to come to a complete stop before mounting
or repositioning a workpiece in the vise.
Never touch a moving blade.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P R E P A R AT I O N
PPRErPAeRATpIONaration Overview Power Supply
The purpose of the preparation section is to help
you prepare your machine for operation. The
list below outlines the basic process to follow
to prepare your machine for operation. Specific
steps for each of these points will be covered in
detail later in this section.
Requirements
Availability
Before installing the machine, consider the
availability and proximity of the required power
supply circuit. If an existing circuit does not meet
the requirements for this machine, a new circuit
must be installed.
The typical preparation process is as follows:
1. Unpack the machine and inventory the
contents of the carton.
To minimize the risk of electrocution, fire,
or equipment damage, installation work and
electrical wiring must be done by a qualified
electrician in accordance with all applicable
2. Clean the machine and its components.
3. Make any necessary adjustments or
inspections to ensure the machine is ready
for operation.
4. Connect the machine to the power source.
Electrocution or fire may
occur if machine is not
correctly grounded and
attached to the power
supply. Use a qualified
electrician to ensure a safe
power connection.
5. Test run the machine to make sure it
functions properly and is ready for operation.
Required for Setup
The items listed below are required to
successfully set up and prepare this machine for
operation.
Full-Load Current Rating
The full-load current rating is the amperage
a machine draws at 100% of the rated output
power. On machines with multiple motors, this is
the amperage drawn by the largest motor or sum
of all motors and electrical devices that might
operate at one time during normal operations.
For Power Connection
•
•
A power source that meets the minimum
circuit requirements for this machine. (Refer
to the Power Supply Requirements
section for details.)
A qualified electrician to ensure a safe and
code-compliant connection to the power
source.
Full-Load Rating at 110V.................. 8.6 Amps
Full-Load Rating at 220V.................. 4.3 Amps
The full-load current is not the maximum
amount of amps that the machine will draw. If
the machine is overloaded, it will draw additional
amps beyond the full-load rating.
If the machine is overloaded for a sufficient
length of time, damage, overheating, or fire may
result—especially if connected to an undersized
circuit. To reduce the risk of these hazards,
avoid overloading the machine during operation
and make sure it is connected to a power supply
circuit that meets the requirements in the
following section.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P R E P A R AT I O N
Circuit Information
A power supply circuit includes all electrical
equipment between the main breaker box or fuse
panel in your building and the incoming power
Grounding Requirements
In the event of certain types of malfunctions or
breakdowns, grounding provides a path of least
resistance for electric current—in order to reduce
connections inside the machine. This circuit must
be safely sized to handle the full-load current
that may be drawn from the machine for an
extended period of time.
For 110V Connection (Prewired)
This machine is equipped with a power cord
that has an equipment-grounding wire and a
grounding plug (similar to the figure below).
The plug must only be inserted into a matching
receptacle (outlet) that is properly installed and
grounded in accordance with all local codes and
For your own safety and protection of property,
consult a qualified electrician if you are unsure
about wiring practices or electrical codes in
your area.
GROUNDED
Note: The circuit requirements listed in this
manual apply to a dedicated circuit—where only
one machine will be running at a time. If this
machine will be connected to a shared circuit
where multiple machines will be running at
the same time, consult a qualified electrician to
ensure that the circuit is properly sized for safe
operation.
5-15 RECEPTACLE
Grounding Prong
5-15 PLUG
Current Carrying Prongs
Figure 2. NEMA 5-15 plug and receptacle.
Circuit Requirements for 110V
This machine is prewired to operate on a 110V
power supply circuit that has a verified ground
and meets the following requirements:
For 220V Connection
Use the plug type listed in the Circuit
Requirements for this voltage. The listed plug
(similar to the figure below) has an equipment-
grounding wire to safely ground the machine.
The plug must only be inserted into a matching
receptacle (outlet) that is properly installed and
grounded in accordance with all local codes and
ordinances.
Nominal Voltage ...............................110V/120V
Cycle .............................................................60 Hz
Phase ..............................................Single-Phase
Circuit Rating....................................... 15 Amps
Plug/Receptacle (included)...........NEMA 5-15
GROUNDED
Circuit Requirements for 220V
6-15 RECEPTACLE
This machine can be converted to operate on
a 220V power supply. To do this, follow the
Voltage Conversion instructions included in
this manual. The intended 220V circuit must
have a verified ground and meet the following
requirements:
Current Carrying Prongs
6-15 PLUG
Nominal Voltage ...............................220V/240V
Cycle .............................................................60 Hz
Phase ..............................................Single-Phase
Circuit Rating....................................... 15 Amps
Plug/Receptacle ...............................NEMA 6-15
Grounding Prong
Figure 3. NEMA 6-15 plug and receptacle.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P R E P A R AT I O N
Extension Cords
We do not recommend using an extension cord
with this machine. If you must use one, only
use it if absolutely necessary and only on a
temporary basis.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power until
instructed later in this manual.
Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without
yellow stripes) is the equipment-grounding wire.
If repair or replacement of the power cord or
plug is necessary, do not connect the equipment-
grounding wire to a live (current carrying)
terminal.
Any extension cord used with this machine
must contain a ground wire, match the required
plug and receptacle listed in the Circuit
Requirements for the applicable voltage, and
meet the following requirements:
Check with a qualified electrician or service
personnel if you do not understand these
grounding requirements, or if you are in doubt
about whether the tool is properly grounded.
Minimum Gauge Size............................16 AWG
Maximum Length (Shorter is Better) ....50 ft.
If you ever notice that a cord or plug is
damaged or worn, disconnect it from power, and
immediately replace it with a new one.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P R E P A R AT I O N
Unpacking
J
This item was carefully packaged to prevent
damage during transport. If you discover any
damage, please immediately call Customer
Service at (360) 734-1540 for advice. You may
need to file a freight claim, so save the containers
and all packing materials for possible inspection
by the carrier or its agent.
I
K
L
Inventory
A. Handle ............................................................1
B. Axle.................................................................1
C. Wheels ............................................................2
D. Leveling Feet..................................................2
E. Handwheel .....................................................1
Description (Figure 4)
Qty
Figure 5. Stand components.
Hardware (Not Shown)
Qty
•
•
Hex Nut 1⁄4"-20 (Vertical Operation) .............1
Flat Head Screw 1⁄4"-20 x 1⁄2
"
(Vertical Operation).......................................1
Hex Wrench 4mm ..........................................1
Hex Bolt M8-1.25 x 15 .................................21
Hex Nut M8-1.25..........................................19
Flat Washer 8mm ........................................40
Hex Bolt M12-1.75 x 25 ................................4
Flat Washer 12mm ........................................5
Knob M6-1 x 15 ..............................................1
Cotter Pins .....................................................2
•
•
•
•
•
•
•
•
F
Handwheel Handle ........................................1
G. Pulley Cover ...................................................1
H. V-Belt..............................................................1
A
B
C
The items listed below are optional components
and are not required for bandsaw operations.
Their installation and use is covered in
E
F
D
Operation, beginning on Page 19. Parts A and
D are required for Vertical Cutting (Page 30).
G
H
Description
Qty
M. Table (Vertical Operation).............................1
N. Work Stop.......................................................1
O. Work Stop Rod ...............................................1
P. Table Support (Vertical Operation) ..............1
Figure 4. Small components.
M
O
Description (Figure 5)
Qty
I. Rear Panel......................................................1
J. Right Side Panel ............................................1
K. Front Panel.....................................................1
L. Left Side Panel...............................................1
P
N
Figure 6. Optional components.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P R E P A R AT I O N
4. Attach the right side panel (the side without
the handle) to the stand assembly as shown
in Figure 9 with (7) M8-1.25 x 15 hex bolts,
(7) M8-1.25 hex nuts, and (14) 8mm flat
washers.
Assembly
1. Attach the front and rear panels of the stand
together as shown in Figure 7 with (6) M8-
1.25 x 15 hex bolts, (6) M8-1.25 hex nuts hex
nuts, and (12) 8mm flat washers.
To assemble the bandsaw:
Right Side
Panel
x7
Stand
Assembly
Rear Panel
Front Panel
x6
Figure 9. Left side panel assembly.
5. Repeat the above step for the right side
panel using (6) M8-1.25 x 15 hex bolts,
(6) M8-1.25 hex nuts, and (12) 8mm flat
washers (see Figure 10 for assembled view).
Figure 7. Front and rear panel assembly.
2. Place the assembly upside down on wood
blocks to avoid scratching it or damaging the
mounting tabs.
3. Attach the handle to the left side panel as
shown in Figure 8 with two M8-1.25 x 15
hex bolts and 8mm flat washers.
Left Side Panel
x2
Figure 10. Stand assembly.
Handle
Figure 8. Handle installation.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P R E P A R AT I O N
6. Insert the axle through the holes in the base
assembly, then slide the wheels over the axle
and secure each with a cotter pin, as shown
in Figure 11.
8. With the help of another person, flip the
stand assembly right-side up, then lift the
bandsaw assembly and place it onto the
stand assembly.
9. Secure the bandsaw to the stand with four
M12-1.75 x 25 hex bolts and 12mm flat
washers, as shown in Figure 13.
Axle
Base
Wheel
Hex Bolts
(2 of 4 Shown)
Cotter Pin
Figure 11. Wheel assembly.
(Handwheel Not Yet
Installed)
7. Thread the leveling feet into the stand
assembly, as shown in Figure 12. You can
adjust these later as needed to level the
bandsaw.
Figure 13. Mounting bandsaw to stand.
10. Loosen the belt tension bolt shown in Figure
14.
Leveling
Feet
(Pulley Cover Not
Belt Tension Bolt
Yet Installed)
Figure 12. Leveling feet.
Figure 14. Belt tension bolt location.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P R E P A R AT I O N
11. Pivot the motor assembly upward, then place
the belt over the gearbox and motor pulleys,
as shown in Figure 15.
Motor Pulley
Gearbox
Pulley
Knob Location
Motor
Assembly
Figure 17. Pulley cover knob.
13. Slide the vise handwheel onto the leadscrew
and tighten the set screw shown in Figure
18. Thread the handle into the handwheel
and tighten it.
Figure 15. Installing belt.
12. Install the pulley cover (Figure 16) with two
M6-1 x 12 hex bolts, three 6mm flat washers,
and the South Bend cast aluminum knob
(see Figure 17).
Leadscrew
Belt
Hex Bolts
Cover
Handle
Set Screw
Handwheel
Figure 18. Vise handwheel.
Figure 16. Pulley cover.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P R E P A R AT I O N
Cleaning & Protecting
The unpainted surfaces are coated at the factory
with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
The benefit of this rust preventative is that it
works very well. The downside is that it can be
time-consuming to thoroughly remove.
Many cleaning solvents are
toxic if inhaled. Minimize
your risk by only using
these products in a well
ventilated area.
Be patient and do a careful job when cleaning
and removing the rust preventative. The time
you spend doing this will reward you with
smooth-sliding parts and a better appreciation
for the proper care of the unpainted surfaces.
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner that may
damage painted surfaces. Always follow the
manufacturer’s instructions when using any
type of cleaning product.
Although there are many ways to successfully
remove the rust preventative, we have cleaned
thousands of machines and found the following
process to be the best balance between efficiency
and minimized exposure to toxic fumes or
chemicals.
Basic steps for removing rust preventative:
1. Put on safety glasses and disposable gloves.
2. Coat all surfaces that have rust preventative
with a liberal amount of your cleaner or
degreaser and let them soak for a few
minutes.
Before cleaning, gather the following:
•
•
Disposable rags
Cleaner/degreaser (certain citrus-based
degreasers work extremely well and they
have non-toxic fumes)
3. Wipe off the surfaces. If your cleaner or
degreaser is effective, the rust preventative
will wipe off easily.
•
Safety glasses & disposable gloves
Note: To clean off thick coats of rust preventative
on flat surfaces, such as beds or tables, use
a PLASTIC paint scraper to scrape off the
majority of the coating before wiping it off
with your rag. (Do not use a metal scraper or
it may scratch the surface.)
Note: Automotive degreasers, mineral spirits, or
WD•40 can be used to remove rust preventative.
Before using these products, though, test them
on an inconspicuous area of a painted area to
make sure they will not damage it.
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a
quality metal protectant or light oil to
prevent rust.
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used for
cleaning. Avoid using these
products to remove rust
preventative.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P R E P A R AT I O N
Weight Load
Location
Refer to the Machine Specifications for the
weight of your machine. Make sure that the
Physical Environment
surface upon which the machine is placed will
The physical environment where your machine
is operated is important for safe operation and
longevity of parts. For best results, operate this
machine in a dry environment that is free from
excessive moisture, hazardous or flammable
chemicals, airborne abrasives, or extreme
conditions. Extreme conditions for this type
of machinery are generally those where the
ambient temperature is outside the range of 41°–
104°F; the relative humidity is outside the range
of 20–95% (non-condensing); or the environment
is subject to vibration, shocks, or bumps.
bear the weightofthemachine,additional
equipment that may be installed on the machine,
and the heaviest workpiece that will be used.
Additionally, consider the weight of the operator
and any dynamic loading that may occur when
operating the machine.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space aroundthe machineforadequate
operator material handling or the installation
of auxiliary equipment. With permanent
installations, leave enough space around
the machine to open or remove doors/covers
as required by the maintenance and service
described in this manual.
Electrical Installation
Place this machine near an existing power
source. Make sure all power cords are protected
from traffic, material handling, moisture,
chemicals, or other hazards. Make sure to leave
access to a means of disconnecting the power
source or engaging a lockout/tagout device.
Children or untrained
people may be seriously
injured by this machine.
Only install in an access
restricted location.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed
safely. Shadows, glare, or strobe effects that
may distract or impede the operator must be
eliminated.
19"
Power
Connection
35¾"
16¾"
6" Min.
38"
(Drawing Not to Scale)
Figure 19. Clearances.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P R E P A R AT I O N
3. Open the downfeed valve and allow the
saw to travel all the way down. If the blade
contacts the machine base or the auto-
OFF tab rests on the toggle switch, adjust
the downfeed stop bolt as described in
Downfeed Stop Bolt, on Page 35.
Power Connection
Electrocution or fire
may occur if machine is
ungrounded, incorrectly
connected to power, or
connected to an undersized
circuit. Use a qualified
electrician to ensure a safe
power connection.
4. Connect the machine to the power source.
5. Put on safety glasses and secure loose
clothing or long hair.
6. Lift the bandsaw by the handle. Close the
downfeed valve to prevent it from lowering.
Once your machine is set up and assembled as
previously described in this manual, it is ready to
be connected to the power source.
7. Start the bandsaw while keeping your finger
near the ON/OFF toggle switch at all times
during the test run. The bandsaw should run
smoothly with little or no vibration.
•
If you plan to use the machine at 110V,
simply plug it into a receptacle on a 110V
circuit that meets the requirements listed on
Page 10.
— If you suspect any problems, immediately
turn the bandsaw OFF, disconnect it from
power, and correct the problem before
continuing.
•
If you plan to use the machine at 220V, you
will have to convert the machine for 220V.
Refer to Electrical, beginning on Page 41.
— If you need any help with your bandsaw
call our Tech Support at (360) 734-1540.
8. Open the downfeed valve to lower the saw
through its full range of motion. When it
reaches the bottom of its travel, it should
turn OFF. If it does not, manually turn it
OFF, disconnect it from power, then proceed
immediately to Auto-Off Tab, on Page 37.
Test Run
After all preparation steps have been completed,
the machine and its safety features must be
tested to ensure correct operation. If you discover
a problem with the operation of the machine or
its safety components, do not operate it further
until you have resolved the problem.
Inspections &
Adjustments
Note: Refer to Troubleshooting on Page 38 for
solutions to common problems that occur with
metal-cutting bandsaws. If you need additional
help, contact our Tech Support at (360) 734-1540. The following list of adjustments were performed
at the factory before your machine was shipped.
If you find that the adjustments are not set
according to the procedures in this manual or
your personal preferences, re-adjust them.
To test run your machine:
1. Read and follow the safety instructions at
the beginning of the manual, take required
safety precautions, and make sure the
machine is set up and adjusted properly
•
•
•
Blade Tracking .................................Page 35.
Squaring the Blade ..........................Page 37.
Blade Guide Bearings ......................Page 36.
2. Clear away all tools and objects used during
assembly and preparation.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
O P E R AT I O N
OPERATION
To complete a typical operation, the operator
does the following:
1. Examines the workpiece to make sure it is
Operation Overview
The purpose of this overview is to provide
the novice machine operator with a basic
understanding of how the machine is used during
operation, so they can more easily understand
the controls discussed later in this manual.
suitable for cutting.
2. Checks/adjusts the V-belt position on the
pulleys to ensure the correct cutting speed
for the workpiece.
Note: Due to the generic nature of this overview,
it is not intended to be an instructional guide
for performing actual machine operations.
To learn more about specific operations and
machining techniques, seek training from people
experienced with this type of machine, and do
additional research outside of this manual by
reading "how-to" books, trade magazines, or
websites.
3. Raises the head, then closes the downfeed
valve.
4. Adjusts the vise angle for the operation, then
securely clamps the workpiece in the vise.
5. Lowers the saw bow close to the workpiece,
then adjusts the guide post to within 1" of
the workpiece, and verifies that the blade is
properly tensioned.
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before beginning
any operations.
6. Adjusts the guide post so the opening
between the two blade guides is
approximately 1⁄4" larger than the width of
the workpiece.
7. Makes sure the workpiece and bandsaw are
stable and that there are no obstructions in
the way of the cut.
8. Puts on safety glasses.
Loose hair, clothing, or
jewelry could get caught
in machinery and cause
serious personal injury.
Keep these items away
from moving parts at all
times to reduce this risk.
9. Starts the bandsaw and waits for the blade
to reach full speed.
10. Opens the downfeed valve to lower the head
and blade into the workpiece, then allows
the bandsaw to complete the cut.
11. Once the bandsaw has stopped, raises the
head, and removes the workpieces.
During operation, small
metal chips may become
airborne, leading to serious
eye injury. Wear safety
glasses to reduce this risk.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
O P E R AT I O N
I. Head Locking Pin: Can be inserted into one
of three holes to lock the head in the down,
up, or vertical positions.
Controls
Refer to Figures 20–21 and the following
descriptions to become familiar with the basic
controls of this machine.
J. Vise Jaw Lock Bolt: Locks the vise jaw at
the angle set by the operator.
A. Blade Tension Knob: Adjusts the position
of the upper blade wheel to apply or release
blade tension.
K. Feed Pressure Handle: Controls the feed
pressure by increasing or decreasing preload
on the feed pressure spring.
B. Guide Post Knob: Locks the guide post in
the position set by the operator.
L. Transport Handle: Provides a solid control
point for moving the machine.
C. Downfeed Rate Adjust Knob: Controls
the speed at which the blade lowers into the
workpiece.
M. Fence Scale: Indicates the angle of the vise
fence.
D. Downfeed Valve: Controls the starting and
N. Vise Fence Bolts (behind fence): Lock the
stopping of the headstock downfeed.
fence at the angle set by the operator.
E. Work Stop Lock Knob: Locks the work stop
J
K
in the position set by the operator.
I
F. ON/OFF Toggle Switch: Turns the saw
motor ON or OFF.
G. Vise Jaw Handwheel: Controls the vise jaw
N
movement.
M
H. Downfeed Stop Bolt: Adjusts to determine
L
the absolute bottom limit of blade travel.
C
B
Figure 21. Rear Identification.
A
G
H
F
D
E
Figure 20. Front Identification.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
O P E R AT I O N
E. Tooth Rake: The angle of the tooth face
Blade Selection
from a line perpendicular to the length of the
blade.
Selecting the right blade for the cut requires a
knowledge of various blade characteristics. This
section breaks down blade characteristics to help
the reader make an informed decision about
what blade to use for a given operation.
F. Gullet Depth: The distance from the tooth
tip to the bottom of the curved area (gullet).
G. Tooth Pitch: The distance between tooth
tips.
Blade Terminology
H. Blade Back: The distance between the
bottom of the gullet and the back edge of the
blade.
A
B
C
I. Blade Pitch or TPI: The number of teeth per
inch measured from gullet to gullet.
Blade Length
Measured by the blade circumference, blade
lengths are usually unique to the brand of your
bandsaw and the distance between the wheels.
F
E
H
D
G
I
Model
Blade Length
SB1017.............................................................641⁄2
"
Figure 22. Bandsaw blade terminology.
Blade Width
A. Kerf: The width of the cut made during
operation.
Measured from the back of the blade to the tip
of the blade tooth (the widest point), blade width
is often the first consideration given to blade
selection. Blade width dictates the largest and
smallest curve that can be cut, as well as how
accurately it can cut a straight line—generally
the wider the blade, the straighter it will cut.
B. Tooth Set: The distance each tooth is bent
left or right from the blade.
C. Gauge: The thickness of the blade.
D. Blade Width: The widest point of the blade
measured from the tip of the tooth to the
back edge of the blade.
Model
Blade Width
SB1017.................................................................1⁄2
"
Curve Cutting: Curve cutting can only be
performed while the machine is in the vertical
position. See Vertical Operation on Page 30
for more information on vertical cutting. The
smallest radius curve that can accurately be cut
with a 1⁄2" blade width is approximately 21⁄2".
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
O P E R AT I O N
Tooth Set
Three common tooth sets are alternate, wavy,
and raker (see Figure 23). Each removes
material in a different manner when cutting the
workpiece.
Standard (or Raker)
Variable Pitch (VP)
Variable Pitch Positive Rake
Hook (or Claw)
Figure 23. Bandsaw blade tooth sets.
Skip (or Skip Tooth)
Alternate: An all-purpose arrangement of
bending the teeth evenly left and right of the
blade. Generally used for milder metals.
Figure 24. Bandsaw blade tooth types.
Wavy: Generally three or more teeth in a group
that are bent one way, followed by a non-set
tooth, and then a group bent the other way.
Recommended for straight cuts in thin metals or
thin-wall tubing.
Variable Pitch (VP): Varying gullet depth and
tooth spacing, a "0" rake angle, excellent chip
removing capacity, and smooth cutting.
Variable Pitch with Positive Rake: Varying
gullet depth and tooth spacing, a positive rake
angle, better chip formation, and aggressive
cutting.
Raker: Three teeth in a recurring group—one
bent left, next one bent right, and then a non-
set tooth. The raker set is ideal for most contour
cuts.
Hook or Claw: Wide gullets (round or flat),
equally spaced teeth, positive rake angle, and
fast cut with good surface finish.
Tooth Type
The most common tooth types are described
below and illustrated in Figure 24.
Skip or Skip Tooth: Wide, flat gullets, a "0" rake
angle, equally spaced teeth, and recommended
for non-ferrous materials.
Standard or Raker: Equally spaced teeth set at
a "0" rake angle. Recommended for all purpose
use.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
2. Refer to the "Material Width/Diameter"
O P E R AT I O N
Blade Pitch (TPI)
row of the blade selection chart in Figure
25, and read across to find the workpiece
thickness you need to cut.
The chart below is a basic starting point for
choosing teeth per inch (TPI) for variable pitch
blades and standard raker set bi-metal blades/
HSS blades. However, for exact specifications
of bandsaw blades that are correct for your
operation, contact the blade manufacturer.
3. Refer to the "Material Shapes" row and find
the shape of the material to be cut.
4. In the applicable row, read across to the
right and find the box where the row and
column intersect. Listed in the box is the
minimum TPI recommended for the variable
tooth pitch blades.
To select the correct blade pitch:
1. Measure the material thickness. This
measurement is the distance from where
each tooth enters the workpiece to where it
exits the workpiece.
Material Width/Diameter
Material Shapes
Teeth Per Inch (TPI) for Bandsaw Blades
TOOTH SELECTION
mm
50
75
5/8
100
4/6
150
200
250
300
12
350
1.4/2.5
400
2/3
450
1.5/.8
3/4
9
2/3
4/6
3/4
1.5/.8
2/3
6
1.4/2.5
10 11
3/4
2 2½ 3 3½
inch
4
5
7
8
13 14 15 16 17 18
19
Figure 25. General guidelines for blade selection and speed chart.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
O P E R AT I O N
Blade Changes
Change blades when they become dull, damaged,
or if the operation requires a different type of
blade.
Blade T
r
av
el
To change the blade on the bandsaw:
1. DISCONNECT BANDSAW FROM POWER!
2. Raise the head of the bandsaw to the vertical
position, use the head locking pin to hold it
in place, then remove the wheel access cover.
3. Loosen the tension knob and slip the blade
Figure 27. Blade cutting direction.
off of the wheels.
6. When the blade is around both wheels,
adjust the position so the back of the blade is
against the shoulder of the wheels as shown
in Figure 28.
4. Install the new blade through both blade
guide bearings, as shown in Figure 26, and
around the bottom wheel.
!
!
Wheel Shoulder
Blade
Guide
Bearings
Figure 26. Installing blade.
Figure 28. Installing blade around wheel.
5. Hold the blade around the bottom wheel with
one hand and slip it around the top wheel with
the other hand, keeping the blade between the
blade guide bearings.
7. Tighten the tension knob so the blade will
not slip on the wheels upon startup.
8. Connect the bandsaw to the power source.
Note: It is sometimes possible to flip the
blade inside out, in which case the blade will
be installed in the wrong direction. Check to
make sure the blade teeth are facing toward
the workpiece, as shown in Figure 27, after
mounting to the bandsaw. Some blades will
have a directional arrow as a guide.
9. Briefly turn the bandsaw ON then OFF to
position the blade and resume the previous
tracking.
— If the tracking needs to be adjusted, see
Blade Tracking on Page 35.
— If the tracking is fine, proceed to Blade
Tension on Page 25.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
O P E R AT I O N
blade selection
Blade Tension
Blade Breakage
Proper tension is essential to avoid vibration,
twist, or`slippage on the wheels. A correctly
tensioned blade provides long life, straight cuts,
and efficient cutting times.
Many conditions may cause a bandsaw blade to
break. Some of these conditions are unavoidable
and are the natural result of the stresses to
which bandsaw blades are subjected. Other
causes of blade breakage are avoidable.
The three major signs of incorrect tension are:
1) The blade stalls in the cut and slips on the
wheels, 2) the blade frequently breaks, and 3) the
cuts are not straight.
The most common causes of avoidable blade
breakage are:
•
Faulty alignment or adjustment of the blade
guides.
To tension the blade on the bandsaw:
1. Make sure the blade is tracking properly
•
Forcing or twisting a wide blade around a
tight radius.
(refer to Blade Tracking on Page 35).
2. DISCONNECT BANDSAW FROM POWER!
•
•
•
•
Feeding the workpiece too fast.
Dull or damaged teeth.
Over-tensioned blade.
3. Loosen and slide the blade guide as far out
as it will go, then tighten it down again.
4. Turn the tension knob in Figure 29
clockwise to tighten the blade or clockwise to
loosen the blade.
Top blade guide assembly set too high above
the workpiece. Adjust the top blade guide
assembly so that there is approximately 1⁄4
"
!
Blade
Tension
Knob
between the bottom of the assembly and the
workpiece. Understand that with smaller
workpieces, this may not be possible. In
these cases, simply adjust the blade guide as
far down as possible.
•
•
Using a blade with a lumpy or improperly
finished braze or weld.
Continuously running the bandsaw when not
in use.
•
•
Leaving the blade tensioned when not in use.
Using the wrong blade pitch (TPI) for the
workpiece thickness. The general rule of
thumb is to have no fewer than three teeth
in contact with the workpiece when cutting.
Figure 29. Adjusting blade tension.
5. Using moderate finger pressure, push
against the side of the blade. If the blade
flexes more than 1⁄8", tighten the blade
tension knob further, then repeat this step.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
O P E R AT I O N
Blade Care & Break-In Blade Speed
The bandsaw is capable of operating at 80,
Blade Care
120, or 200 FPM (Feet Per Minute). The speed
can easily be adjusted by changing the V-belt
placement. Figure 30 shows the pulley positions
required for each speed. The charts on the
following page provide guidelines for determining
which speed to use for a cutting operation
To prolong blade life, always use a blade with
the proper width, set, type, and pitch for each
application. Maintain the appropriate feed
rate, feed pressure, and blade speed. Keep your
blades clean, since dirty or gummed up blades
pass through the cutting material with much
more resistance than clean blades, causing
unnecessary heat.
Gearbox Pulley
Motor Pulley
80 FPM
120 FPM
200 FPM
Blade Break-In
The tips and edges of a new blade are extremely
sharp. Cutting at too fast of a feed rate or too
slow of a blade speed can fracture these tips and
edges, causing the blade to quickly become dull.
Properly breaking-in a blade allows these sharp
edges to wear without fracturing, thus keeping
the blade sharp longer.
Figure 30. Pulley & V-belt configuration.
To change the blade speeds:
Use the Chip Inspection Chart on Page 27
to ensure that the optimal blade speed and feed
rate are being used.
1. DISCONNECT BANDSAW FROM POWER!
2. Open the belt cover, then loosen the belt
tension bolt shown in Figure 31 to allow the
motor to pivot.
To properly break-in a new blade:
1. Choose the correct speed for the blade and
material of the operation.
Belt Tension Bolt
2. Reduce the feed pressure by half for the first
50–100 in2 of material cut.
3. To avoid twisting the blade when cutting,
wait until the total width of the blade is in
the cut before adjusting the feed pressure.
Figure 31. Motor tension bolt.
3. Lift the motor to relieve the belt tension
and position the belt in the desired pulley
alignment.
4. Release the motor and let its weight tension
the belt.
5. Re-tighten the belt tension bolt and close the
belt cover.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
O P E R AT I O N
Blade Speed Chart
The blade speed chart in Figure 32 offers guidelines for various metals, given in feet per minute
(FPM). Choose the closest available machine blade speed to the number shown in the chart. Refer to
the Chip Inspection Chart that follows for recommendations on adjusting your operation based on
the appearance of the chips produced
Speed FPM
(M/Min)
Speed FPM
(M/Min)
Speed FPM
(M/Min)
Speed FPM
(M/Min)
Material
Material
Material
Material
Carbon
Steel
Free Machining
Stainless Steel
196~354
203
111~321
150~203
Alloy
Tool Steel
(60) (108)
(62)
(34) (98)
(46) (62)
Steel
75~118
246
(75)
108~225
(33) (75)
High-Speed
Tool Steel
180~220
(54) (67)
Angle
Steel
Gray
Mold Steel
(25) (36)
Cast Iron
Water
Ductile
Austenitic
Cast Iron
180~220
(54) (67)
242
(75)
65~85
Cold-Work
Tool Steel
95~213
Thin
Hardened
Tool Steel
(20) (26)
(29) (65)
Tube
203
(62)
220~534
(67) (163)
Stainless
85
321
Aluminum
Alloy
Hot-Work
Tool Steel
Malleable
Steel
(26)
(98)
Cast Iron
203~213
(62) (65)
Copper
Alloy
229~482
(70) (147)
85-203
Oil-Hardened
Tool Steel
CR Stainless
Steel
220
(67)
Plastics
(26) (62)
Figure 32. Dry cutting blade speed chart.
Chip Inspection Chart
The best method for choosing the cutting speed and feed rate for a cutting operation is to inspect the
chips created by the cut. These chips will be indicators of what is commonly referred to as the "chip
load". Refer to the chip inspection chart below to evaluate chip characteristics and determine whether
to adjust feed rate/pressure, blade speed, or both.
Chip
Appearance
Chip
Description
Chip
Color
Blade
Speed
Feed Rate/
Pressure
Other
Actions
Thin & Curled
Silver
Good
Good
Hard, Thick &
Short
Brown or Blue
Brown or Blue
Increase
Increase
Decrease
Decrease
Hard, Strong &
Thick
Hard, Strong,
Curled & Thick
Silver or Light
Brown
Decrease
Slightly
Check Blade
Pitch
Check Blade
Pitch
Good
Increase
Good
Hard, Coiled & Thin
Straight & Thin
Powdery
Silver
Silver
Silver
Decrease
Increase
Increase
Decrease
Coiled, Tight &
Thin
Check Blade
Pitch
Silver
Good
Decrease
Figure 33. Chip inspection chart.
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
O P E R AT I O N
Downfeed Pressure Work Stop
The downfeed pressure is controlled by the
spring and handle shown in Figure 34.
The work stop can be used to make uniform-
length cuts on multiple workpieces.
To decrease downfeed pressure, twist the handle
clockwise to increase spring tension.
To install and use the work stop:
1. Insert the work stop rod into the machine
base (as shown in Figure 36), then tighten
the set screw to secure it.
To increase downfeed pressure, twist the handle
counterclockwise to release spring tension.
Set Screw
Handle
Work Stop
Rod
Work Stop
Work Stop
Set Screw
Spring
Figure 36. Downfeed rate controls.
Figure 34. Downfeed rate controls.
2. Slide the work stop onto the work stop rod,
adjust it as needed to provide a stop for the
workpiece, then tighten the work stop set
screw.
Downfeed Rate
The downfeed valve starts and stops headstock
downfeed.
The downfeed rate is adjusted by turning the
downfeed rate adjust knob (Figure 35). Turning
the knob clockwise decreases the downfeed rate
and turning the knob counterclockwise increases
the downfeed rate.
Downfeed Rate
Adjust Knob
Downfeed
Valve
Figure 35. Downfeed pressure.
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
O P E R AT I O N
2. Use the scale as a guide to set your angle or
use a machinist square to set the angle of the
vise fence, as shown in Figure 38.
Vise
Always turn the saw OFF and allow the blade
to come to a complete stop before using the
vise! Failure to follow this caution may lead to
injury.
The vise can hold material up to six inches wide
and be set to cut angles from 0° to 45°.
Tools Needed
Wrench or Socket 12mm.......................................1
Machinist Square..................................................1
Qty
Scale
To use the vise:
1. Loosen the two hex bolts shown in Figure
Figure 38. Squaring vise to blade.
37.
3. Tighten the hex bolts.
4. Loosen the hex bolt on the vise jaw so the
jaw can float, then match the angle of the
workpiece and re-tighten the hex bolt.
Hex Bolts
5. Tighten the vise against the workpiece.
Figure 39 shows the correct methods for
holding different workpiece shapes.
NOT
RECOMMENDED
RECOMMENDED
Figure 37. Vise hex bolts.
Figure 39. Workholding options by material shape.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
O P E R AT I O N
Blade Guide
The upper blade guide should be positioned as
close to the workpiece as possible for all cutting
operations. The support provided by keeping
the blade guides close ensures straight cuts by
keeping the blade from twisting and drifting off
the cut line.
Downfeed Ram
Cap Screw
To adjust the blade guide:
1. DISCONNECT BANDSAW FROM POWER!
Figure 41. Downfeed ram cap screw location.
2. Loosen the knob shown in Figure 40 and
slide the blade guide to within 1⁄4" of the
workpiece, then re-tighten the knob.
4. Remove the two flat head screws and the
blade guide cover shown in Figure 42.
!
!
Flat
Head
Screws
Blade Guide
Blade
Guide
Cover
Knob
Figure 42. Blade guide cover.
Figure 40. Blade guides.
5. Install the table with the two screws
removed in Step 2.
Vertical Cutting
6. Install the table bracket with the pre-
installed hex bolt, the M6-1 x 12 flat head
screw, and the M6-1 hex nut, as shown in
Figure 43.
The Model SB1017 can easily be set up for
vertical cutting operations.
To convert the saw for vertical cutting:
1. DISCONNECT BANDSAW FROM POWER!
Table
2. Open the downfeed valve and allow the saw
to lower fully.
Table Bracket
3. Unthread and remove the downfeed ram cap
screw shown in Figure 41, then pivot the
saw bow up into the vertical position. Push
the head locking pin (Figure 1) inward to
lock the saw in the upright position.
Pre-installed Hex Bolt
Figure 43. Table installed.
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
O P E R AT I O N
7. Place a level on the table, as shown in
Figure 44, then use the vertical stop bolt
shown in Figure 45 along with the slotted
table mount bracket to level the table.
Operation Tips
The following tips will help you safely and
effectively operate your bandsaw and help you
get the maximum life out of your saw blades.
Horizontal Cutting
•
Use the work stop to quickly and accurately
cut multiple pieces of stock to the same
length.
•
•
Clamp the material firmly in the vise jaws to
ensure a straight cut through the material.
Let the blade reach full speed before
engaging the workpiece. Never start a cut
with the blade in contact with the workpiece.
Figure 44. Leveling vertical setup.
•
•
Pay attention to the chips produced by the
cutting operation and use their appearance
to fine-tune the blade speed, feed speed,
and pressure (refer to the Chip Inspection
Chart on Page 27).
Wait until the blade has completely stopped
before removing the workpiece from the vise,
and avoid touching the cut end—it could be
very hot!
Vertical
Stop Bolt
Vertical Cutting
•
Do not cut workpieces that cannot be
properly supported or stabilized without
a vise in the vertical position. Examples
are chains, cables, round or oblong-shaped
workpieces, workpieces with internal or
built-in moving or rotating parts, etc.
Figure 45. Vertical stop bolt (blade cover removed for
clarity).
•
•
Make sure that the vertical table assembly is
securely fastened to the bandsaw frame so it
will adequately support the workpiece.
Adjusts the guide post so the opening
between the two blade guides is
approximately 1⁄4" larger than the width of
the workpiece.
Release blade tension at the end of each use
to prolong blade life.
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
SBL Gearhead T-Shirt
SBL One Good Turn T-Shirt
100% Cotton, preshrunk T-shirts, available in
sizes S, M, L, XL, 2XL, 3XL.
A C C E S S O R I E S
ACCESSORIES
Accessories
This South Bend merchandise may be available
through your local South Bend Lathe Co. dealer.
If you do not have a dealer in your area, please
call us at (360) 734-1540 or email us at
SB1298—SBL Bench Lathe Shop Clock
SB1299—SBL Toolroom Lathe Shop Clock
SB1300—SBL Lathe with Man
These fine traditional shop clocks are constructed
with a metal antique-finished frame. They are
easy to read from a distance and measure 14"
in diameter. Pictures just don't do them justice.
They are very nice quality clocks and perfect for
the South Bend Lathe aficionado.
SB1298
SB1299
Figure 47. Official South Bend Lathe T-Shirts.
SB1300
Figure 46. Antique-finished South Bend shop clocks.
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
M A I N T E N A N C E
MAINTENANCE
Maintenance Schedule Lubrication
For optimum performance from your machine,
follow this maintenance schedule and refer to
any specific instructions given in this section.
Before applying lubricant, wipe the area clean for
best results. Lubricate the components shown in
Figure 48 with multi-purpose gear grease.
Guide
Post
!
Always disconnect
machine from power before
performing maintenance or
serious personal injury may
result.
Tension
Leadscrew
Daily
•
•
•
•
•
Check/correct loose mounting bolts.
Check/correct damaged or dull saw blade.
Check/correct worn or damaged wires.
Clean/protect table.
Clean metal chips from upper and lower
wheel areas.
Vise Leadscrew
Figure 48. Lubrication locations.
•
Correct any other unsafe condition.
Gearbox
At least once a year, drain and replace the
gearbox oil.
Monthly
•
•
Check for V-belt tension, damage, or wear.
Lubricate tension leadscrew, guide post, and
vise leadscrew.
Items Needed
Qty
Wrench 4mm .........................................................1
Mobil Spartan EP220 or ISO 220 EP Equivalent
Gear Oil ........................ Approximately 1 Pint
Handheld Oil Pump ..............................................1
Shop Rags...............................................As needed
Wooden Blocks .......................................As needed
Yearly
•
Lubricate gearbox.
Cleaning
To change the gearbox oil:
1. DISCONNECT BANDSAW FROM POWER!
Use a brush and a shop vacuum to remove chips
and other debris from the machine. Keep the
non-painted surfaces rust-free with regular
applications of a high-quality rust preventative.
2. Loosen the four hex bolts that secure the
machine to the cabinet.
Periodically, remove the blade and thoroughly
clean all metal chips or built-up grease from the
wheel surfaces and blade housing.
3. With the help of another person, carefully
remove the saw from the stand and place
it on a workbench. Use wooden blocks to
support the machine so that the gearbox
cover is horizontal, as shown in Figure
49. This will prevent spilling of oil in the
following steps. Make sure the machine is
sufficiently supported and stable so that it
will not shift during this procedure.
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
M A I N T E N A N C E
!
Belt Tension Bolt
Hex Bolts
Downfeed
Ram Bracket
Gear Box
Cover
Gear Box
Figure 50. Motor tension bolt.
Figure 49. Gear box location.
3. Lift the motor to relieve the belt tension,
4. Remove the four hex bolts that secure the
gearbox cover, then remove the gearbox
cover and downfeed ram bracket.
then remove the belt.
4. Install a new belt, then release the motor
and let its weight tension the belt.
5. Use a handheld oil pump to draw the oil out
of the gearbox, then use a rag to remove any
remaining oil and sediment.
5. Re-tighten the belt tension bolt and close the
belt cover.
6. Add oil to the gearbox until it is
approximately half full, then replace the
gearbox cover.
Machine Storage
All machinery will develop serious rust problems
and corrosion damage if it is not properly
prepared for storage. If decommissioning this
machine, use the steps in this section to ensure
that it remains in good condition.
V-Belt Replacement
If the V-belt shows signs of excessive wear, such
as cracking or fraying, it must be replaced.
To prepare your machine for storage or
decommission it from service:
To replace the V-belt
1. DISCONNECT BANDSAW FROM POWER!
1. DISCONNECT BANDSAW FROM POWER!
2. Open the belt cover, then loosen the belt
tension bolt shown in Figure 50 to allow the
motor to pivot.
2. Thoroughly clean all unpainted, bare metal
surfaces, then coat them with a light weight
grease or rust preventative. Take care to
ensure these surfaces are completely covered
but that the grease or rust preventative is
kept off of painted surfaces.
If the machine will be out of service for only
a short period of time, use way oil or a good
grade of medium-weight machine oil (not
auto engine oil) in place of the grease or rust
preventative.
3. Loosen or remove the belt so it does not
become stretched during storage.
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
M A I N T E N A N C E
4. Fill the gearbox with the recommended gear
oil so components above the normal oil level
do not develop rust. (Make sure to put a tag
on the controls as a reminder for the re-
commissioning process to adjust the gear oil
level before starting the machine.)
Blade Tracking
The tracking will only need to be adjusted if the
blade rubs against the wheel shoulder or moves
more than 1⁄16" away from the shoulder.
Tools Needed
Wrench or Socket 14mm.......................................1
Qty
If the machine will be out of service for only
a short period of time, start the machine
once a week and run all gear-driven
components for a few minutes. This will
put a fresh coat of gear oil on the gearing
components inside the gearbox.
To adjust the blade tracking on the bandsaw:
1. DISCONNECT BANDSAW FROM POWER!
2. Position the bandsaw in the vertical position.
5. Completely cover the machine with a tarp
or plastic sheet that will keep out dust and
resist liquid or moisture. If machine will be
stored in/near direct sunlight, use a cover
that will block the sun's rays.
3. Open the wheel access cover.
4. Loosen, but do not remove the lower hex bolt
in the blade wheel tilting mechanism shown
in Figure 52.
!
Downfeed Stop Bolt
The downfeed stop bolt serves to stop downfeed
movement. Proper placement of the downfeed
stop bolt prevents the blade from contacting the
machine base and the auto-OFF tab from resting
on the ON/OFF toggle switch, while still allowing
the blade to move lower than the table surface to
complete the cut.
Lower
Hex Bolt
To adjust the downfeed stop bolt, loosen the lock
nut, turn the stop bolt as needed to position it as
described above, then re-tighten the lock nut.
Figure 52. Blade tracking adjustments.
Downfeed Stop
Bolt
Lock Nut
Figure 51. Downfeed stop bolt.
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
M A I N T E N A N C E
5. Use the blade tension knob to release the
Blade Guide Bearings
blade tension, as shown in Figure 53.
The blade guide bearings must be properly
adjusted to make square cuts. One bearing on
each assembly has an eccentric bushing that
allows it to be adjusted to properly support the
blade. The bearings are secured in place by a hex
nut and lock washer, as shown in Figure 54.
!
Blade
Tension
Knob
Tracking
Set Screw
Backing Bearing
Figure 53. Adjusting tracking hex bolt.
Hex Nut
6. Adjust the tracking set screw, as shown in
Figure 53, then tighten the lower hex bolt
loosened in Step 4.
Eccentric
Bushing
— Tightening the tracking set screw will
move the blade closer to the shoulder of
the wheel.
Figure 54. Blade guide adjustments.
To adjust the blade guide bearings:
1. DISCONNECT BANDSAW FROM POWER!
— Loosening the tracking set screw will
move the blade away from the shoulder.
2. Position the saw in the vertical position (see
Vertical Operation on Page 30 for more
information).
7. Tension the blade.
8. Reconnect the power and turn the bandsaw
3. Loosen the hex nuts that secure the eccentric
ON.
bushings attached to the guide bearings.
— If the blade tracks along the shoulder of
the wheel (without rubbing), the blade is
tracking properly and this adjustment is
completed.
4. Adjust the eccentric bushing as necessary so
that it pushes against the blade just enough
to hold the blade flat between the bearings.
Note: Since the bearings twist the blade
into position, it is acceptable if there is
0.001"–0.002" gap between the blade and
the front or back of the bearing. Just make
sure not to squeeze the blade too tightly with
the bearings. After the guide bearings are
set, you should be able to rotate the guide
bearings (although they will be stiff) with
your fingers.
— If the blade walks away from the shoulder
of the wheel or hits the shoulder, turn the
bandsaw OFF, disconnect it from power,
then repeat Steps 4–8.
9. Turn the bandsaw OFF, disconnect it from
power, then replace the blade guard and
wheel access cover.
5. Adjust the backing bearing in the same
manner, but leave a gap between 0.002–
0.003" from the back of the blade.
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
M A I N T E N A N C E
Squaring Blade
Auto-OFF Tab
The blade can be adjusted square to the vise
table. A blade that is square will improve your
cutting results and extend the life of your blade.
The auto-OFF tab may require adjustment over
time if the machine fails to turn itself OFF at the
end of a cut.
To square the blade to the table:
To adjust the auto-OFF tab:
1. DISCONNECT BANDSAW FROM POWER!
1. DISCONNECT BANDSAW FROM POWER!
2. Separate the blade guides as far as possible,
then lower the bandsaw all the way until it
contacts the downfeed stop bolt.
2. Loosen the hex bolt shown in Figure 56.
3. Place a square on the table bed and against
the edge of the blade, as shown in Figure
55, then check different points along the
length of the table between the blade guides.
Hex Bolt
Auto-OFF Tab
Hex Bolts
Figure 56. Auto-OFF tab.
3. Move the toggle switch to the ON position
(keep the machine disconnected from
power—the motor does not need to be
running for this adjustment).
Figure 55. Squaring the blade.
4. Open the downfeed valve to allow the saw
to move downward. Wait for it to come to a
stop.
4. If the blade is not square to the table, loosen
the hex bolts shown in Figure 55 and
rotate the blade guide bearing assemblies as
necessary until the blade is perpendicular to
the bed, then re-tighten the hex bolts.
5. Push the auto-OFF tab downward into the
toggle switch until the switch moves to the
OFF position. Then, without moving the
auto-OFF tab from this position, tighten the
hex bolt to secure the auto-OFF tab.
6. Lift the saw, move the toggle switch to the
ON position, then allow the saw to move
downward again. Watch to see if the auto-
OFF tab moves the toggle switch to the OFF
position. If it doesn't, loosen the hex bolt,
then repeat Step 5, fine-tuning the position
of the auto-OFF tab as necessary.
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
TROUBLESHOOTING
TIRf OyUoBuLnESeHeOdOrTeINpGlacement parts, or if you are unsure how to do any of the solutions given here, feel free
to call us at (360) 734-1540.
!
Symptom
Possible Cause
Possible Solution
Machine does not
start.
1. Power supply switched off/has
1. Switch power supply on/verify voltage.
incorrect voltage.
2. Blown fuse/tripped circuit breaker
2. Correct the cause of overload, then reset/replace
at main panel.
fuse or breaker.
3. Plug or receptacle is corroded or
3. Clean/retighten contacts; correct the wiring.
mis-wired.
4. Break or short in wiring; or loose
4. Trace/replace broken or corroded wires; fix loose
connections.
connections.
5. Motor connection wired incorrectly.
5. Wire motor correctly (refer to inside junction box
cover or manual).
6. Motor ON/OFF switch at fault.
7. Start capacitor blown or at fault.
8. Centrifugal switch at fault.
9. Motor at fault.
6. Replace switch.
7. Replace start capacitor.
8. Adjust/replace centrifugal switch.
9. Test for shorted windings, bad bearings and repair
or replace.
Motor chatters
1. Extension cord (if used) is causing
1. Move machine closer to the power source or use a
during startup or
during operation.
voltage drop.
larger gauge or shorter extension cord.
2. Power supply has incorrect voltage
2. Contact your power company to fix the power
on one or more legs.
supply.
Machine has
excessive vibration
or noise.
1. Blade is missing teeth.
2. Motor fan rubbing on fan cover.
3. Motor or table is loose.
4. V-belt loose.
1. Replace blade.
2. Fix/replace fan cover; replace loose or damaged fan.
3. Tighten any loose fasteners.
4. Tighten V-belt.
5. Guide post lock lever is loose.
5. Tighten the lock lever.
6. Machine incorrectly mounted on
6. Level/shim base; tighten/adjust mounting hardware
floor.
or feet.
7. V-belt worn or damaged.
7. Replace V-belt. Use a link belt if possible.
8. Pulley loose or not in alignment;
8. Replace worn pulley, key, and shaft, and realign.
shaft bent.
9. Centrifugal switch out of
9. Adjust/replace centrifugal switch.
adjustment; at fault.
10. Motor bearings worn or damaged.
10. Replace motor bearings or replace motor.
-38-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
TROUBLESHOOTING
!
Symptom
Possible Cause
Possible Solution
Machine stalls
or slows when
operating.
1. Too much pressure when feeding
1. Reduce pressure when feeding workpiece.
workpiece.
2. Workpiece is warped and binding
2. Fabricate a jig for better workpiece control.
blade.
3. Blade is not correct for material
3. Use the correct blade for the operation. Refer to
being cut.
Blade Selection section beginning on Page 25.
4. Belt slipping.
4. Tension/replace belt; ensure pulleys are aligned.
5. Motor overheated.
5. Let cool, clean motor, and reduce workload.
6. Motor connection wired incorrectly.
6. Review wiring diagram on motor cover; correct wire
connections.
7. Motor at fault.
7. Test for shorted windings, bad bearings and repair
or replace.
Workpiece angle
incorrect or out of
square.
1. Scale not calibrated or loose vise.
1. Zero fence to blade and realign scale. Tighten any
loose fasteners.
2. Table guide post is loose or out of
2. Tighten any loose hardware or lock levers. Align the
alignment.
guide post (see Page 37).
Machine or blade
bogs down in the
cut.
1. Excessive load on the blade.
1. Reduce feed rate or increase blade speed
2. Blade is dull, wanders, and gets
2. Replace blade, adjust guides and tracking.
pinched in the cut.
3. Blade is dull.
3. Replace blade.
4. The blade TPI is too coarse for the
4. Use a blade with at least 3 teeth contacting the
thin workpiece.
material at all times.
5. Blade is loose.
5. Clean wheels and increase blade tension.
6. V-belt loose; belt squeals at times.
7. Blade is loading up.
6. Tighten V-belt.
7. Install a blade with more suitable TPI or different
style of teeth.
8. V-belt worn and slips.
8. Replace V-belt.
Blade tracks
incorrectly, or
comes off wheels.
1. Feed rate is too fast.
1. Reduce feed rate, or decrease blade TPI.
2. Adjust blade guides.
2. Blade guides need adjustment.
3. Blade is not tracking correctly.
4. Blade is bell-mouthed.
3. Adjust blade tracking.
4. Install new blade, and regularly remove tension
from blade when not in use.
5. Blade is dull, wanders, and gets
5. Replace blade, re-secure the workpiece from
pinched in the cut.
shifting.
6. Rubber tire on wheel is damaged,
6. Replace rubber tires.
glazed, or worn.
7. Blade tension is too loose.
7. Increase blade tension.
8. Incorrect blade for bandsaw.
9. The blade has insufficient support.
8. Install correct blade for machine.
9. Tighten the blade guide as close to the workpiece as
possible without touching it.
10. Wheel tires are loaded with metal
10. Clean wheel tires.
shavings.
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
TROUBLESHOOTING
!
Symptom
Possible Cause
Possible Solution
The cut is crooked,
the blade wanders,
slow cuts, or shows
overheating on one
side of the cut or
the blade.
1. The feed pressure is too high.
1. Decrease the feed rate.
2. Too much side pressure when
2. Feed workpiece straight into the blade (vertical
feeding workpiece in vertical mode.
mode only).
3. Blade is loading up.
3. Install a blade with more suitable TPI or different
style of teeth.
4. Blade tension is too loose.
4. Increase blade tension.
5. Blade installed backwards.
5. Check blade rotation as described in “test run” and
reverse blade if necessary.
6. Dull blade; missing teeth.
6. Replace blade.
7. Blade too wide for size of radius
7. Install a smaller width blade, or increase blade
being cut.
tension.
8. The blade speed is wrong.
8. Adjust feed rate and cutting speed as required.
9. The blade tracking is wrong.
9. Adjust the blade tracking back to normal.
Blade dulls
1. Blade is improperly broken in.
1. Replace blade, and complete blade break-in
prematurely, or
metal sticking to
the blade.
procedure.
2. The blade gullets are loading up
2. Use a blade that has larger gullets to carry out
with chips.
material.
3. The blade TPI is too fine for the
thick workpiece, and the teeth load
up and overheat.
3. Use a coarser-tooth blade, adjust feed rate, adjust
blade speed, make sure the brush is working.
4. The workpiece has hard spots,
4. Replace the blade with a special blade for cutting
welds, or scale.
hardened materials.
Repetitious noise
coming from
machine.
1. Pulley set screws or keys are
1. Inspect keys and set screws. Replace or tighten if
missing or loose.
necessary.
2. Blade is missing teeth.
2. Replace blade.
3. Motor fan is hitting the cover.
3. Adjust fan cover mounting position, tighten fan, or
shim fan cover.
4. V-belt is defective.
4. Replace V-belt.
5. Blade weld contacting blade guides.
6. Blade weld may be failing.
5. Grind blade weld down smaller.
6. Cut and reweld the blade, or replace the blade.
Blade wears on
one side or shows
overheating.
1. The blade guides are worn or mis-
1. Re-adjust or replace the blade guides.
adjusted.
2. The blade support is inadequate.
2. Tighten the blade guide as close to the workpiece as
possible without touching it.
3. Dull or incorrect blade.
3. Replace blade.
4. Blade is bell-mouthed.
4. Install new blade.
Vibration when
operating or
cutting.
1. Loose or damaged blade.
1. Tighten or replace blade.
2. Worn wheel bearing.
2. Check/replace wheel bearing.
3. Replace or dress rubber tires.
3. Wheel tires worn or incorrectly
installed.
4. Bent or dull blade.
4. Replace blade.
5. Wheels out of balance.
6. Loose machine component.
7. V-belt has a high spot.
5. Replace wheels.
6. Tighten loose component.
7. Replace/adjust the V-belt.
8. Check and replace for bad wheel or bearing.
8. Bandsaw blade wheel is bent or out
of balance.
-40-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
E L E C T R I C A L
ELECTRICAL
Electrical Safety Instructions
These pages are accurate at the time of printing. In the constant effort to improve, however, we may
make changes to the electrical systems of future machines. Study this section carefully. If you see
differences between your machine and what is shown in this section, call Technical Support at (360)
734-1540 for assistance BEFORE making any changes to the wiring on your machine.
1. Shock Hazard: It is extremely dangerous to
perform electrical or wiring tasks while the
machine is connected to the power source.
Touching electrified parts will result in
personal injury including but not limited to
severe burns, electrocution, or death. For
your own safety, disconnect machine from
the power source before servicing electrical
components or performing any wiring tasks!
5. Circuit Requirements: Connecting the
machine to an improperly sized circuit will
greatly increase the risk of fire. To minimize
this risk, only connect the machine to a
power circuit that meets the minimum
requirements given in this manual.
6. Capacitors/Inverters: Some capacitors and
power inverters store an electrical charge for
up to 10 minutes after being disconnected
from the power source. To reduce the risk of
being shocked, wait at least this long before
working on capacitors.
2. Wire Connections: All connections must be
tight to prevent wires from loosening during
machine operation. Double-check all wires
disconnected or connected during any wiring
task to ensure tight connections.
7. Wire/Component Damage: Damaged wires
or components increase the risk of serious
personal injury, fire, or machine damage. If
you notice that any wires or components are
damaged while performing a wiring task,
replace those wires or components before
completing the task.
3. Modifications: Using aftermarket parts or
modifying the wiring beyond what is shown
in the diagram may lead to unpredictable
results, including serious injury or fire.
4. Motor Wiring: The motor wiring shown
in these diagrams is current at the time of
printing, but it may not match your machine.
Always use the wiring diagram inside the
motor junction box.
8. Experiencing Difficulties: If you are
experiencing difficulties understanding the
information included in this section, contact
our Technical Support at (360) 734-1540.
WIRING DIAGRAM COLOR KEY
BLUE
WHITE
BLACK
BLUE
PINK
RED
WHITE
YELLOW
GREEN
LIGHT
BLUE
GREEN
PURPLE
TUR-
QUIOSE
YELLOW
GRAY
ORANGE
BROWN
The photos and diagrams included in this section are best viewed in color. You can
NOTICE:
-41-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
E L E C T R I C A L
3. Use a wire nut to connect wires #2, #3, and
220V Conversion
#5, then wrap them with electrical tape.
Wiring diagrams are provided in this section
showing the Model SB1017 wired for both 110V
and 220V. Refer to these diagrams if needed
when following this procedure. Additionally,
you must purchase a 220V toggle switch (Part
No. PSB1017204) in order to complete the
conversion.
4. Connect wires #1 and #6 to the lower right
terminal and wire #4 to the lower right
terminal shown in Figure 58. Tighten the
terminal screws to secure the wires.
Start
220V Wiring
Capacitor
200MFD
125VAC
Items Needed
5A Motor Overload Breaker
Qty.
3
2
MOTOR
OVERLOAD
220V
5
(Part No. PSB1017085-7) ..............................1
NEMA 6-15 Plug ...................................................1
Phillips Screwdriver #2 ........................................1
Wire nut (sized for three 14 Ga. wires)................1
Electrical Tape .......................................As needed
Wire stripper ..........................................As needed
4
Tighten
These
Terminal
Screws
1
6
To convert the Model SB1017 to 220V:
GND
1. DISCONNECT BANDSAW FROM POWER!
Figure 58. Rewired for 220V.
2. Open the motor junction box, then loosen
the wire terminals indicated in Figure
57. Remove the wires connected to those
terminals.
5. Remove the existing motor overload breaker
from the junction box cover by disconnecting
both wires, then un-threading the nut on the
front of the button. Pay close attention to the
wires as you remove them to ensure you re-
install them correction in the next step.
110V Wiring
Start
Capacitor
200MFD
125VAC
6. Install the 5A motor overload breaker (part
No. PSB1017085-7) in place of the one
breaker you removed in Step 5.
MOTOR
OVERLOAD
110V
Loosen These
4
Terminal
Screws
2
5
7. Close the motor junction box.
1
3
6
8. Connect a NEMA 6-15 plug in the place of
the standard plug on the power cord.
GND
9. Insert the plug into a receptacle on a 220V
circuit that meets the requirements listed on
Page 10.
Figure 57. Wiring terminal locations.
READ PAGE 41 BEFORE
DOING ANY WIRING!
-42-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
E L E C T R I C A L
Wiring Diagram
Motor Junction Box
Toggle Switch
Figure 59. Wiring component locations.
Start
ON/OFF
Toggle
Switch
Capacitor
200MFD
125VAC
Motor
(Rewired
for
MOTOR
OVERLOAD
BREAKER
220V
3
2
Ground
5
4
220V)
1
6
Neutral
Hot
GND
Ground
Motor
110V
Start
Capacitor
200MFD
125VAC
MOTOR
OVERLOAD
BREAKER
110V
110 VAC
5-15 Plug
4
(As Recommended)
2
5
Hot
Hot
1
3
6
GND
Ground
220 VAC
6-15 Plug
(As Recommended)
READ PAGE 41 BEFORE
DOING ANY WIRING!
-43-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P A R T S
PARTS
Table
411
410
409
18
52
67
407
31
A
67
404
403
36
35
49
402
401
187
53
122
188
34
39
37
38
A
91
18
157
32
22
156
32-2
27
28-1
28
32-1
91
155
18
157
22
30
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
18
PLW04
PSB1017022
PS52
LOCK WASHER 3/8
WIRE CLIP
PHLP HD SCR 3/8-16 X 1
VISE HANDWHEEL ASSEMBLY
SET SCREW 5/16-18 X 1/2
E-CLIP 10MM
HEX BOLT 5/16-18 X 1
VISE LEADSCREW W/NUT
VISE LEADSCREW
53
67
91
122
155
156
157
187
188
401
PB38
PLW01
PN08
PN19
PN07
PS06
PTLW01
PW07
PN02
PS06
HEX BOLT 7/16-14 X 2
LOCK WASHER 5/16
HEX NUT 3/8-16
HEX NUT 7/16-14
HEX NUT 10-24
PHLP HD SCR 10-24 X 3/8
EXT TOOTH WASHER #10
FLAT WASHER 5/16
HEX NUT 5/16-18
PHLP HD SCR 10-24 X 3/8
FLAT WASHER #10
HYDRAULIC CYLINDER ASSEMBLY
CYLINDER PIVOT ROD
CYLINDER BRACKET CAP SCREW
CYLINDER BRACKET
LOCK WASHER 1/4
22
27
28
PSB1017028
28-1 PSS08
30
31
PEC03M
PB03
PSB1017032
32
32-1 PSB1017032-1
32-2 PSB1017032-2 VISE LEADSCREW NUT
34
35
36
37
38
39
49
PSB1017034
PW02
PB24
PSB1017037
PS06
PSB1017039
PSB1017049
SMALL VISE JAW
FLAT WASHER 3/8
HEX BOLT 3/8-16 X 1-1/4
MACHINE BASE
PHLP HD SCR 10-24 X 3/8
VISE SCALE
402 PW03
403 PSB1017403
404 PSB1017404
407
PSB1017407
409 PSB1017409
410
411
PLW02
PB31
LARGE VISE JAW
HEX BOLT 1/4-20 X 1
-44-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P A R T S
Cabinet Stand
4
4-7
4-6
4-5
4-2
4-13
4-14
4-3
4-9
4-8
4-12
9
4-1
4-4
9-1
9-3
9-4
9-3
9-2
9-2
9-1
4-11
REF PART #
DESCRIPTION
CABINET STAND ASSEMBLY
LEFT PANEL
REF PART #
4-11 PSB1017004-11 FOOT PAD ASSEMBLY
4-12 PSB1017004-12 LIFTING HANDLE
DESCRIPTION
4
PSB1017004
4-1
PSB1017004-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
PSB1017004-2 RIGHT PANEL
PSB1017004-3 REAR/TOP PANEL ASSEMBLY W/DOOR
PSB1017004-4 FRONT PANEL
4-13 PB87M
4-14 PW01M
HEX BOLT M8-1.25 X 15
FLAT WASHER 8MM
WHEEL ASSEMBLY
9
PSB1017009
PB87M
PW01M
PN03M
PB01M
PW04M
HEX BOLT M8-1.25 X 15
FLAT WASHER 8MM
HEX NUT M8-1.25
HEX BOLT M10-1.5 X 30
FLAT WASHER 10MM
9-1
9-2
9-3
9-4
PSB1017009-1 WHEEL
PW14 FLAT WASHER 5/8
PSB1017009-3 COTTER PIN 1/8 X 1"
PSB1017009-4 WHEEL AXLE
-45-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P A R T S
Head
75
104
189
93
92
103
3
90-2
90-3
90
103-5
214
109
90-4
103-3
103-2
90-1
90-5
90-6
90-7
90-5
103-4
103-1
109
81
2
80
72
123
120
73
100
412
79
71
77
77-2
77-5
51
50
71-1
198
113
77-1
59-4
59-3
55-4
55-3
55-2
3
59
3
212
55
55-1
118
51
50
59-1
208
17
61
59-2
54
43
47
207
46
120
45
45-1
50
15
19
21
20
-46-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P A R T S
Head Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
2
PN05
HEX NUT 1/4-20
77-5 PSB1017077-5 BUSHING
3
15
17
19
20
21
43
45
PW06
FLAT WASHER 1/4
TENSION ROD ASSEMBLY
HEAD PIVOT ROD
79
80
81
PSB1017079
PSB1017080
PSB1017081
PSB1017090
BLADE TENSION KNOB BOLT 3/8-16 X 94
COMPRESSION SPRING
HEAD CASTING
PSB1017015
PSB1017017
PSB1017019
PSS17
PSB1017021
PSB1017043
PSB1017045
WORK STOP BRACKET
SET SCREW 5/16-18 X 5/16
WORK STOP ROD
CORD STRAIN RELIEF
RIGHT TENSION ROD BRACKET
LEFT TENSION ROD BRACKET
SPRING HOOK SCREW
TENSION SPRING
HEX BOLT 5/16-18 X 3/4
FLAT WASHER 5/16
PIVOT BRACKET
TABLE ASSEMBLY
FLAT HD SCR 1/4-20 X 1-2
90
TRANSMISSION GEAR ASSEMBLY
90-1 PSB1017090-1 REAR BLADE WHEEL AXLE
90-2 PSB1017090-2 TRANSMISSION GEAR
90-3 PRP20M
90-4 PK23M
90-5 P6202ZZ
90-6 PSB1017090-6 BUSHING
90-7 PSB1017090-7 OIL SEAL
92
ROLL PIN 4 X 22
KEY 5 X 5 X 25
BALL BEARING 6202ZZ
45-1 PSB1017045-1
46
47
50
51
54
55
PSB1017046
PSB1017047
PB07
PW07
PSB1017054
PSB1017055
PSB1017092
PSB1017093
PFH37
GEARBOX GASKET
GEARBOX COVER
93
100
103
FLAT HD SCR 8-32 X 3/8
BLADE TENSION SLIDE ASSEMBLY
SHAFT BLOCK
BLADE TENSION SLIDE PLATE
SET SCREW 5/16-18 X 5/8
FLAT WASHER 5/16
PSB1017103
55-1 PSB1017055-1
55-2 PSB1017055-2 TABLE
55-3 PSB1017055-3 TABLE BRACKET
55-4 PN05
103-1 PSB1017103-1
103-2 PSB1017103-2
103-3 PSS38
HEX NUT 1/4-20
103-4 PW07
59
PSB1017059
REAR SAFETY COVER
FLAT WASHER 1/4
PHLP HD SCR 1/4-20 X 3/8
103-5 PB12
HEX BOLT 5/16-18 X 1-1/4
HEX BOLT 5/16-18 X 1
BLADE TENSION SLIDE GUIDE
BLADE 14TPI 1/2 X 64-1/2"
HEX BOLT 1/4-20 X 1/2
BUSHING 19 X 17 X 7
59-1 PW06
59-2 PS07
59-3 PSB1017059-3 FRONT SAFETY COVER
59-4 PCAP50M
61
104
109
113
PB03
PSB1017109
PSB1017113
PB19
CAP SCREW M5-.8 X 10
SET SCREW 5/16-18 X 5/8
REAR BLADE WHEEL
SET SCREW 5/16-18 X 5/16
BEARING COVER
118
PSS38
PSB1017071
PSS17
PSB1017072
PK23M
PB02
120
123
189
198
207
PSB1017120
PB31
PW07
PR05M
PSB1017207
71
HEX BOLT 1/4-20 X 1
FLAT WASHER 5/16
71-1
72
73
75
77
EXT RETAINING RING 15MM
LOCK PIN
LOCK PIN ASSEMBLY
HEX BOLT 5/16-18 X 1
HEX BOLT 1/4-20 X 5/8
FLAT WASHER 3/8
KEY 5 X 5 X 25
HEX BOLT 1/4-20 X 5/8
FRONT BLADE WHEEL ASSEMBLY
FRONT BLADE WHEEL
208 PSB1017208
PSB1017077
PSB1017077-1
212
214
412
PB03
PB02
PW02
77-1
77-2 PSB1017077-2
FRONT BLADE WHEEL AXLE ASSEMBLY
-47-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P A R T S
Motor & Blade Guides
118
44
116
16
111
159
1
86-1
74
112
86
99
118
116
85
119
111-1
85-1
220V
85-7
85-6
158
110V
85-2
98
85-5
85-4
85-3
99
6
84
101-1
101
69
72
89
35
100
83
94-3
94-2
94
A
94-1
66
40
41
83
35
63
132
134
A
63-11
64-7
64-8
63-7
63-8
63-1
64-10
63-14
64-1
64-5
63-13
63-12
64-11
64-12
64-6
63-5
63-6
64
64-9
63-10
63-3
63-9
63-2
64-3
64-5
64-4
64-2
133
134
63-5
63-4
-48-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P A R T S
Motor & Blade Guides Parts List
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
6
PB07
PN02
PSB1017016
PW02
PS06
PSB1017041
PSB1017044
PSB1017063
HEX BOLT 5/16-18 X 3/4
HEX NUT 5/16-18
MOTOR CORD 18G 3W
FLAT WASHER 3/8
PHLP HD SCR 10-24 X 3/8
WIRE CLIP
POWER CORD 18G 3W 5-15 PLUG
REAR BLADE GUIDE ASSEMBLY
69
72
74
83
84
85
PB24
PSB1017072
PK12M
PB78
PSB1017084
PSB1017085
HEX BOLT 3/8-16 X 1-1/4
BEARING COVER
KEY 5 X 5 X 30
HEX BOLT 1/2-13 X 1-1/4
MOTOR MOUNT PLATE
MOTOR 1/2HP 110/220V 1PH
CORD STRAIN RELIEF
16
35
40
41
44
63
85-1 PSB1017085-1
85-2 PSB1017085-2 MOTOR FAN COVER
85-3 PSB1017085-3 MOTOR FAN
63-1 PSB1017063-1 REAR BLADE GUIDE BRACKET
63-2 PSB1017063-2 LEFT GUIDE SHAFT
85-4 PC200G
S CAPACITOR 200M 125V 1-3/8 X 3
63-3 PSB1017063-3 RIGHT GUIDE SHAFT
63-4 PSB1017063-4 GUIDE EXT RETAINING RING
85-5 PSB1017085-5 MOTOR JUNCTION BOX
85-6 PSB1017085-6 MOTOR OVERLOAD 110V
85-7 PSB1017085-7 MOTOR OVERLOAD 220V 5A
63-5 P6000ZZ
BALL BEARING 6000ZZ
63-6 PSB1017063-6 BEARING PIN 10 X 36
86
PSB1017086
MOTOR PULLEY
63-7 PN11
63-8 PLW04
63-9 PSB1017063-9 DEFLECTOR PLATE
63-10 PFH19
HEX NUT 3/8-24
LOCK WASHER 3/8
86-1 PSS17
SET SCREW 5/16-18 X 5/16
OIL SEAL TC 15 X 35 X 7
WORM GEAR SHAFT ASSEMBLY
WORM GEAR SHAFT
89
94
PSB1017089
PSB1017094
FLAT HD SCR 1/4-20 X 3/8
94-1 PSB1017094-1
94-2 P6202ZZ
63-11 PSB1017063-11 REAR BLADE GUIDE ARM
BALL BEARING 6202ZZ
63-12 PB12
63-13 PLW01
63-14 PW07
HEX BOLT 5/16-18 X 1-1/4
LOCK WASHER 5/16
FLAT WASHER 5/16
FRONT BLADE GUIDE ASSEMBLY
FRONT BLADE GUIDE BRACKET
94-3 PSB1017094-3 SPACER
98
99
100
101
101-1 PSS18
111
PCAP25
PW07
PFH37
CAP SCREW 5/16-18 X 1-3/4
FLAT WASHER 5/16
FLAT HD SCR 8-32 X 3/8
WORM GEAR PULLEY
SET SCREW 5/16-18 X 3/4
BELT COVER
64
PSB1017064
64-1 PSB1017064-1
PSB1017101
64-2 PSB1017064-2 LEFT GUIDE SHAFT
64-3 PSB1017064-3 RIGHT GUIDE SHAFT
64-4 PSB1017064-4 GUIDE EXT RETAINING RING
PSB1017111
111-1
112
PSB1017111-1
PVA22
BELT COVER PANEL
V-BELT A22
64-5 P6000ZZ
BALL BEARING 6000ZZ
64-6 PSB1017064-6 BEARING PIN 10 X 36
116
118
119
132
133
134
158
159
PW06
PB19
FLAT WASHER 1/4
HEX BOLT 1/4-20 X 1/2
PLASTIC WASHER
REAR BLADE GUIDE SAFETY COVER
FRONT BLADE GUIDE SAFETY COVER
PHLP HD SCR 8-32 X 1/4
PLASTIC CUP
64-7 PN11
HEX NUT 3/8-24
64-8 PLW04
LOCK WASHER 3/8
PSB1017119
PSB1017132
PSB1017133
PS23
PSB1017158
PS18
64-9 PSB1017064-9 FRONT BLADE GUIDE ARM
64-10 PB12
64-11 PLW01
64-12 PW07
HEX BOLT 5/16-18 X 1-1/4
LOCK WASHER 5/16
FLAT WASHER 5/16
66
PSB1017066
BLADE GUIDE KNOB BOLT 3/8-16 X 1-1/4
PHLP HD SCR 10-24 X 1/4
-49-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
P A R T S
Switch
76
76-1
76-2
76-3
203
203-7
203-6
203-2
203-1
203-3
203-4
ON
OFF
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
76
PSB1017076
SWITCH SHUT-OFF ASSEMBLY
SWITCH SHUT-OFF PLATE
FLAT WASHER 1/4
203-2 PSB1017203-2 SWITCH COVER
203-3 PSB1017203-3 SWITCH INDICATOR PLATE
203-4 PSB1017203-4 SWITCH HEX NUT
76-1 PSB1017076-1
76-2 PW06
76-3 PB02
203 PSB1017203
203-1 PSB1017203-1
HEX BOLT 1/4-20 X 5/8
TOGGLE SWITCH ASSEMBLY
TOGGLE SWITCH
203-6 PS08
203-7 PSB1017203-7 CORD RETAINER
PHLP HD SCR 10-24 X 3/4
-50-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
P A R T S
Machine Labels
307
306
305
308
304
303
310
309
313
312
311
301
302
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
PSB1017301
MACHINE ID LABEL
308 PSBLABEL01HS READ MANUAL LABEL
302 PSB1017302
MODEL NUMBER LABEL
309 PSBLABEL13VS DOOR CLOSED WARNING LABEL
303 PSBLABEL15S ELECTRICITY LABEL
310
311
312
313
PSBPAINT01
PSBPAINT03
SB1320
SB LT GRAY TOUCH-UP PAINT
SB DK BLUE TOUCH-UP PAINT
SOUTH BEND NAMEPLATE 125MM
SB LT BLUE TOUCH-UP PAINT
304 PSB1017304
BELT COVER WARNING LABEL
305 PSBLABEL02HS DISCONNECT WARNING LABEL
306 PSB1017306
CUTTING HAZARD WARNING LABEL
PSBPAINT02
307 PSBLABEL04HS EYE INJURY WARNING LABEL
The safety labels provided with your machine are used to make the operator aware of the
machine hazards and ways to prevent injury. The owner of this machine MUST maintain the
original location and readability of these safety labels. If any label is removed or becomes
unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at
-51-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model SB1017
For Machines Mfg. Since 8/09
N O T E S
-52-
Download from Www.Somanuals.com. All Manuals Search And Download.
For Machines Mfg. Since 8/09
Model SB1017
W A R R A N T Y
WARRANTY & RETURNS
This quality product is warranted by South Bend Lathe Company to the original buyer for one year
from the date of purchase. This warranty does not apply to consumable parts, or defects due to any
kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not
reimburse for third party repairs. In no event shall we be liable for death, injuries to persons or
property, or for incidental, contingent, special or consequential damages arising from the use of our
products.
We do not warrant or represent that this machine complies with the provisions of any law, act, code,
regulation, or standard of any domestic or foreign government, industry, or authority. In no event
shall South Bend’s liability under this warranty exceed the original purchase price paid for this
machine. Any legal actions brought against South Bend Lathe Company shall be tried in the State of
Washington, County of Whatcom.
This is the sole written warranty for this machine. Any and all warranties that may be implied by
law, including any merchantability or fitness, for any purpose, are hereby limited to the duration of
this warranty. To take advantage of this warranty, contact us by mail or phone to give us the details
of the problem you are having.
Thank you for your business and continued support.
-53-
Download from Www.Somanuals.com. All Manuals Search And Download.
South Bend Lathe Co.
P.O. Box 2027
Bellingham, WA 98227
PHONE: (360) 734-1540 (Administrative Offices)
FAX: (360) 676-1075 (International)
FAX: (360) 734-1639 (USA only)
southbendlathe.com
Printed In Taiwan
#JB12681
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Shark Carpet Cleaner S3501WC User Manual
Sharp DVD Player XL HF302PHT User Manual
Sharp Microwave Oven R 22AM User Manual
Sharp Projector PG M20X User Manual
Snapper Lawn Mower 1600 User Manual
Snapper Lawn Mower 07225 User Manual
Sony Camcorder Accessories HDR CX7 User Manual
Sony Ericsson Home Theater System BDV E300 User Manual
Spirit Cordless Telephone Communications System ConnecT R User Manual
Swann DVR SW242 2LP User Manual