Sony GPS Receiver NV U44 User Manual

4-000-806-11 (1)  
US  
Instruction Manual  
Personal Navigation System  
Instruction Manual  
NV-U44  
©2008 Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
continue to next page r  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Common procedures to operate the system are explained.  
General operations can be performed on the touch screen. Gently touch the displayed icons with  
your finger.  
Note  
Do not press the display with excessive force. Do not use any sharp object, such as a pen, etc., to tap on  
the display.  
Menu operations  
The main menu appears when you turn on the unit (except during route guidance, in which case  
the map appears).  
1
2
MENU  
VOICE/  
POS.  
3
4
5
6
7
1 Press to show the main menu.  
2 To check the battery status and current time.  
3 Press to show the current position on the map.  
4 Touch to show the navigation menu.  
5 Touch to show the application menu.  
6 Touch to show the setting menu.  
7 Touch to return to the previous display.  
continue to next page r  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Other basic menu operations  
To  
Touch  
cancel the setting  
“Cancel”  
confirm the selection/proceed to the next step “Done” or “OK”  
About the battery status indication  
The battery status can be checked by the indicator in the main menu.  
Indicator  
Status  
Adapter connected.  
Fully charged.  
Not fully charged.  
Low battery.  
Battery is empty. Charge battery immediately.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Gesture Command operations  
Frequently-used operations can be performed by assigning finger strokes such as a line, etc.  
For navigation  
In the map display (except in map scrolling mode), draw the command stroke as below.  
To  
Make  
start navigation to your home (page 15)  
a circumflex  
an “L” shape  
start navigation to a destination stored in  
Favorites (page 20)  
“Favorite 1”  
“Favorite 2”  
a mirror-reversed “L”  
a clockwise circle  
change map scale to the “Preset Scale”  
a counterclockwise circle  
continue to next page r  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
For photo playback  
In the photo playback display, draw the command stroke as below.  
For details on photo playback, see page 37.  
To  
Make  
start the slideshow  
(only when playback controls are shown)  
a dot  
skip to the previous file  
skip to the next file  
a horizontal line (right to left)  
a horizontal line (left to right)  
skip to the previous folder  
a vertical line (downwards)  
a vertical line (upwards)  
skip to the next folder  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Keyboard operations  
The keyboard display appears when you need to enter text.  
When entering addresses, you need only enter characters in upper case, as the system  
automatically converts them to appropriate characters. You can change the case or enter special  
characters/symbols when necessary.  
The following types of keyboards are selectable:  
• “QWERTY + 123”: QWERTY layout with number keys.*  
• “QWERTY”: Large QWERTY layout without number keys.*  
• “ABC”: Alphabetical layout without number keys.  
* “QWERTY” refers to the top row of letters, reading from the left, of a traditional typewriter style keyboard.  
For details on how to change the setting, see page 43.  
QWERTY layout with number keys:  
Entry field  
continue to next page r  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To  
Touch  
enter an alphabetical character  
enter a number  
the desired character key  
the desired number key*1  
enter a special character  
“ÀŐŇ” to switch to the special character  
keyboard, then the desired character; and  
“ABC” to switch back  
enter a symbol  
“@!?” to switch to the symbol keyboard, then  
the desired symbol key; and “ABC” to switch  
back  
enter a space  
“Space”  
“Backspace”  
“Caps”  
delete a character  
change the case  
proceed to the next step  
show the candidate list*2  
confirm the entry  
“Next”  
“Search”  
“Done”  
*1 When another keyboard type is selected, touch “123” to switch to the numeric keyboard.  
*2 The candidate list automatically appears when candidates are narrowed down as you continue inputting  
characters.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Navigation  
Checking the GPS status  
About the GPS status indication  
The GPS status can be checked by the color of the current position icon.  
If the current position is not displayed, press VOICE/POS. to show the icon.  
Current position icon  
Indication  
Status  
Signals are insufficient for navigation.  
Reception temporarily interrupted (e.g., in a tunnel).  
Signals are sufficient for navigation.  
Note  
Acquisition of GPS signal may take up to 10 minutes, especially for the first time. Make sure that you are in  
an open space for faster acquisition.  
Tip  
If GPS signal reception is poor after turning on the unit, the information bar appears at the top of the  
display.  
You can also check the GPS status by the message on the information bar.  
By touching the information bar, you can jump to the display where you can view detailed GPS status  
information (page 12).  
continue to next page r  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Viewing detailed GPS status information  
Detailed GPS status information, such as the latitude, longitude, etc., can be viewed to check if  
the current position is properly calculated.  
1 In the menu display, touch  
, “General,then “GPS Status.”  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Route searching  
You can search for a route in various ways.  
The following route search methods are available.  
Address search  
Address search allows you to set the destination by entering the address information such as  
house number, street name, etc.  
Note on the state selection  
The system recognizes the state you usually drive in and sets it as default, so that you do not need to enter  
the same state name at each address search.  
When GPS detects that the current position is not in the default state, the state selection display  
automatically appears, allowing you to set the desired state.  
Full address search  
Follow the procedure below if you know the house number, street name, and the city name of the  
destination.  
1 In the menu display, touch  
, then “Enter Address.”  
If the state selection display appears, select the new (current) state or “Change to Different  
State.”  
When selecting “Change to Different State,” enter the state name, then select the desired state.  
The house number input display appears.  
2 Enter the house number.  
The street name input display appears.  
3 Enter the street name.  
The list of street candidates appears.  
4 Select the desired street in the list.  
The city name input display appears.  
5 Enter the city name.  
The list of city candidates appears.  
continue to next page r  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6 Select the desired city in the list.  
If more than one address candidate exists, the list of candidates appears. In this case, select  
the desired address.  
The address confirmation display appears.  
7 Select “Go.”  
Route guidance starts.  
Street search  
If the house number is not known, a search can be made to an approximate point on the street.  
1 In the menu display, touch  
, then “Enter Address.”  
If the state selection display appears, select the new (current) state or “Change to Different  
State.”  
When selecting “Change to Different State,” enter the state name, then select the desired state.  
The house number input display appears.  
2 Select “Skip” without entering the house number.  
The search method options appear.  
3 Select “Representative Point of the Street.”  
The street name input display appears.  
4 Enter the street name.  
The list of street candidates appears.  
5 Select the desired street in the list.  
If more than one city or address candidate exists, the setting display(s) appears. In this case,  
set the city or select the address.  
The address confirmation display appears.  
6 Select “Go.”  
Route guidance starts.  
To set the destination in another state  
You can select a different state when “State” appears in the name input displays.  
Select “State,” enter the state name, then select the desired state.  
Tips  
The state can be set by entering its standard 2-letter abbreviation (e.g., NY for New York).  
The list of state/city/street candidates automatically appears without touching “Search” when narrowed  
down to 4 candidates.  
continue to next page r  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Home search  
If you register your home, you can search for a route there.  
For details on registering your home, see page 42.  
1 In the menu display, touch  
, then “Take Me Home.”  
Route guidance starts.  
Tip  
If you select “Take Me Home” without having registered a home address, the registration display  
automatically appears.  
With Gesture Command  
In the map display, draw  
.
POI search  
POI (Points Of Interest) search allows you to set facilities such as restaurants, hotels, gas  
stations, etc., as the destination.  
The system searches for POIs near the current position.  
To search for the POIs in another city  
You can specify the city before selecting the POI search method.  
In this case, the system searches for POIs in the city center.  
1 In the menu display, touch  
, then “Find a Place.”  
The search method selection display appears.  
2 Select “Points of Interest.”  
3 Select “Change City.”  
4 Enter the city name.  
5 Select the desired city in the list.  
To switch back to the nearby search, select “Nearby.”  
continue to next page r  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
By POI name  
You can search for a route to a POI by directly entering its name.  
1 In the menu display, touch  
, then “Find a Place.”  
The search method selection display appears.  
2 Select “Points of Interest.”  
3 Select “By Name.”  
The POI name input display appears.  
4 Enter the POI name.  
The list of POI candidates appears in order of distance from the current position.  
5 Select the desired POI.  
The POI confirmation display appears.  
6 Select “Go.”  
Route guidance starts.  
Tip  
If there are too many POI candidates in the list after step 4 above, you can narrow down by selecting  
category(ies). Select “Category” to show the category list, then select the desired category(ies).  
continue to next page r  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
By POI category  
You can search for a route to a POI by selecting its category(ies).  
1 In the menu display, touch  
, then “Find a Place.”  
The search method selection display appears.  
2 Select “Points of Interest.”  
3 Select “Category.”  
The list of category candidates appears.  
4 Select the desired category.  
Select sub category when necessary until the POI candidates are narrowed down.  
The list of candidates appears in order of distance from the current position.  
5 Select the desired POI.  
The POI confirmation display appears.  
6 Select “Go.”  
Route guidance starts.  
Tip  
If there are too many POI candidates in the list after step 4 above, you can narrow down by entering the  
POI name. Select “Name” to show the POI name input display, then enter the POI name.  
Intersection search  
The intersection can be set as a destination, if available for the selected street.  
1 In the menu display, touch  
, then “Find a Place.”  
The search method selection display appears.  
2 Select “Find Intersection.”  
The street name input display appears.  
3 Enter the street name.  
The list of street candidates appears.  
4 Select the desired street in the list.  
If more than one city candidate exists, the city name input display appears. In this case, enter  
the city name, then select the desired city.  
The street name input display appears.  
5 Enter the other street name.  
The list of street candidates appears.  
6 Select the street.  
The address confirmation display appears.  
7 Select “Go.”  
Route guidance starts.  
Tip  
The intersection search can also be made by selecting “Enter Address” in step 1 above and skipping the  
house number input. For details, see “Street search” on page 14.  
continue to next page r  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
City center search  
The city center can be set as a destination.  
1 In the menu display, touch  
, then “Find a Place.”  
The search method selection display appears.  
2 Select “Find City.”  
The city name input display appears.  
3 Enter the city name.  
The list of city candidates appears.  
4 Select the desired city in the list.  
The address confirmation display appears.  
5 Select “Go.”  
Route guidance starts.  
Tip  
The city center search can also be made by selecting “Enter Address” in step 1 above and skipping the  
house number input. For details, see “Street search” on page 14.  
Quick Link search  
Quick Link allows for quick access to the preset POI name/category.  
Frequently-used POI categories (e.g., “Gas Station”) are preset in Quick Links as default, which  
can be changed if desired.  
1 In the menu display, touch  
, then “Find a Place.”  
The search method selection display appears.  
2 Select the desired Quick Link.  
The list of POI candidates appears in order of distance from the current position.  
3 Select the desired POI.  
The POI confirmation display appears.  
4 Select “Go.”  
Route guidance starts.  
continue to next page r  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Changing a POI name/category in Quick Links  
1 In the menu display, touch  
, then “Find a Place.”  
2 Select “Quick Link Settings,then the desired Quick Link.  
3 Select the desired setting method.  
Select  
To set  
By Name  
the POI name.  
Enter the name.  
Category  
the POI category.  
Select category(ies).  
Category and By Name  
the POI category and name.  
Select category(ies) c “By Name,” then  
enter the name.  
Recent destinations search  
The system stores previous destinations, allowing you to select one quickly from the list.  
For details on how to delete the history, see page 35.  
1 In the menu display, touch  
, then “My Places.”  
The search method selection display appears.  
2 Select “Recent Destinations.”  
The list of searched destinations appears in reverse chronological order.  
3 Select the desired item in the list.  
The address/POI confirmation display appears.  
4 Select “Go.”  
Route guidance starts.  
continue to next page r  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Address book search  
You can select the destination saved in the address book.  
For details on how to manage the address book, see page 35.  
1 In the menu display, touch  
, then “My Places.”  
The search method selection display appears.  
2 Select “Address Book.”  
The list of groups appears.  
3 Select the desired group.  
The list of data in the selected group appears.  
4 Select the desired entry in the list.  
The address/POI confirmation display appears.  
5 Select “Go.”  
Route guidance starts.  
Favorites search  
You can select a destination that is saved in the Favorites.  
For details on how to manage Favorites, see page 36.  
1 In the menu display, touch  
, then “My Places.”  
The search method selection display appears.  
2 Select “Favorite 1,Favorite 2,Favorite 3,or “Favorite 4.”  
Route guidance starts.  
With Gesture Command  
In the map display, draw one of the command strokes:  
– Favorite 1:  
– Favorite 2:  
continue to next page r  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Option menu in the address/POI confirmation display  
The option menu in the address/POI confirmation display provides various useful operations.  
When the confirmation display appears after setting a destination, select “Options,” then one of  
the following items.  
Item  
Purpose  
Save This Location*1 (page 35)  
Edit Item*1 (page 41)  
Interim Destination*2 (page 32)  
Saves the selected point to the address book.  
Edits the selected address book entry.  
Adds the point as an interim destination in the  
current route. The system navigates you to  
this point before the current destination.  
*1 Appears depending on your selection. “Edit Item” appears when you select “My Places” c “Address  
Book.In other cases, “Save This Location” appears.  
*2 Available only during route guidance.  
Fine adjusting the destination point  
You can jump from the address/POI confirmation display to the map scrolling mode, and fine  
adjust the destination point.  
1 Select “Map” in the address/POI confirmation display.  
The map in the scrolling mode appears.  
For details on the map scrolling mode, see page 25.  
2 Drag the screen to fine adjust the destination point, then select “Go.”  
Route guidance starts.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Map operations  
Indications on the map  
When no route guidance is in progress:  
A
B
C
D
E
A Current direction (page 44)  
B Current speed (page 44)  
C Current position/GPS status indication (page 11)  
D North indicator/current time  
E Current street name  
continue to next page r  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
During route guidance:  
Straight-ahead driving  
F
G
H
F Distance/ETA (Estimated Time of Arrival) to destination  
G Distance to next turn  
H Next instruction  
Approaching an intersection  
I
I Next turn instruction  
continue to next page r  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Approaching an intersection (closer)*  
J
K
J Magnified view of an intersection (page 46)  
K Bar indication of the distance to next turn  
Approaching an intersection (even closer)*  
L
L Current position  
* You can set to hide the magnified view of an intersection (page 46).  
continue to next page r  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Map scrolling mode  
You can switch to map scrolling mode by touching the map, whether during route guidance or  
not.  
By placing the desired point into the crosshair, you can view the information on the point or open  
the map options.  
Operations in map scrolling mode  
To  
Operation  
scroll a map  
drag the screen  
touch the point  
move the desired point to the center of the  
screen  
pan the map  
touch and hold the center of the crosshair  
until the beep sounds, then drag it in the  
desired direction  
exit the map scrolling mode  
press VOICE/POS.  
(The current position reappears.)  
continue to next page r  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Using the map tools  
The map tool bar appears when you touch “Options” on the map display.  
1
2
MENU  
VOICE/  
POS.  
3
4
5
6
7
8
1 To show the main menu.  
2 To toggle the map orientation (heading up/north up).  
3 During route guidance:  
To repeat the last voice guidance.  
In other cases:  
To return to the current position display.  
4 To show more map options.  
5 To show the turn-by-turn list (page 33).*  
6 To zoom in/out the map.  
Touch  
7 To adjust the voice guidance volume.  
Touch  
/
.
/
.
To turn off the sound, touch  
.
8 To hide the map tool bar.  
* Available only during route guidance.  
continue to next page r  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
More map options  
More options are available by selecting “More…” in the map tool bar.  
Item  
Purpose  
Navigate to Here*1  
Save This Location (page 35)  
Edit Item*2 (page 41)  
Quit Navigation*3  
Starts route guidance to the point.  
Saves the point to the address book.  
Edits the address book entry.  
Exits the current route guidance.  
Skip to Next Destination*3*4*5 (page 32) Reroutes to skip to the next destination.  
Block Route*3*4 (page 32)  
Routes a detour for a specified distance from  
the current position.  
Search from Here*1*4  
Searches for POIs near the selected point.  
*1 Available only for the point selected in map scrolling mode.  
*2 Available only for address book entry icons.  
*3 Available only during route guidance.  
*4 Appears when  
is touched.  
*5 Available only if more than one destination point exists.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Route planning  
Creating a new itinerary  
The procedure to create a new itinerary is explained below.  
1 In the menu display, touch  
, then “Route Planning.”  
2 Select “Route Planning,then “Options.”  
3 Select “New Route.”  
The route planning display appears in which the current position is set as the start point.  
For details on how to change the start point, see “Editing route points” on page 30.  
4 Select “Add” to add a route point in your itinerary.  
The search method selection display appears.  
5 Select the desired search method to set the route point.  
Select  
To set  
Enter Address  
Home  
by address search (page 13)  
your home as the route point (page 15)  
Find a Place  
by POI search (page 15), intersection search  
(page 17), city center search (page 18), or  
Quick Link search (page 18)  
My Places  
by recent destinations search (page 19),  
address book search (page 20), or Favorites  
search (page 20)  
Browse Map  
a route point from the map display (page 25)  
the current position as the route point  
Current Position  
continue to next page r  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
6 After setting the route point, select “Done.”  
The route planning display reappears with the selected point added in the list.  
The last setting is listed as the final destination.  
Repeat step 4 to 6 to continue adding route points. Up to 10 route points can be set.  
7 Select “Calculate Route.”  
The route calculation starts.  
After the calculation is complete, the route confirmation display appears.  
8 Select one of the following items.  
Item  
Purpose  
Go  
Starts the route guidance.  
Changes the route calculation conditions.  
Change Condition  
continue to next page r  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Editing route points  
You can edit the selected route points while creating an itinerary.  
Select the desired route point in the route planning display, then one of the following items.  
Item  
Purpose  
Change Location  
Shows the search method selection display to  
set the route point again.  
Delete  
Deletes the selected point from the itinerary.  
Changes the order of route points.  
Change Order  
Select the point to move c  
/
c “Done.”  
Tip  
You can open the route planning display and modify your itinerary, even after starting route guidance.  
continue to next page r  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Option menu for route planning  
The option menu in the route planning/route confirmation display provides various useful  
operations.  
When the route planning/route confirmation display appears, select “Options,” then one of the  
following items.  
Item  
Purpose  
Save Route  
Saves the current route.  
Select an unregistered line in the list, then  
enter the name.  
To overwrite a registered route, select a  
registered line in the list c “OK.”  
Saved Routes*1  
Edits the route/starts the route guidance.  
Select the route, then one of the following  
options.  
– “Edit”: Shows the route planning display to  
edit the route point.  
– “Rename”: Changes the name of the  
selected route.  
– “Delete”: Deletes the selected route.  
– “Start Navigation”: Starts the route  
guidance.  
Route Profile (page 45)  
Shows/changes the current route profile  
settings.  
Calculation Condition*1  
Sets the route calculation conditions.  
New Route*1  
Shows the route planning display to create a  
new itinerary.  
Sort by Distance*1  
Sorts the route points in order of distance  
from the start point.  
Simulation*2  
Simulates the current route.  
*1 Appears only in the option menu of the route planning display while setting the route point(s).  
*2 Appears only in the option menu of the route confirmation display after setting the route points.  
continue to next page r  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Adding an interim destination to the current route  
During route guidance, you can add an interim destination.  
1 In the menu display, touch  
, then select the desired search method to set  
the interim destination.  
For details on search methods, see “Route searching” on page 13.  
You can select the desired search method, except for home search and Favorites search.  
2 After setting the interim destination, select “Options” in the address/POI  
confirmation display.  
3 Select “Interim Destination.”  
The route guidance to the interim destination starts.  
Skipping to the next destination  
If more than one destination point exists during route guidance, you can cancel the current  
destination and reroute to skip to the next destination.  
1 In the map display, select “Options,More...,then  
2 Select “Skip to Next Destination.”  
.
The current destination is canceled, and the route guidance to the next destination starts.  
Blocking the route  
During route guidance, you can detour for a specified distance from the current position. For  
example, if traffic congestion occurs ahead of the route, you can reroute to avoid this area.  
1 In the map display, select “Options,More...,then  
.
2 Select “Block Route.”  
The distance setting display appears.  
3 Select the desired distance, then “Detour.”  
Recalculation starts.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Route confirmation  
Viewing the turn-by-turn list  
During route guidance, you can view the turn-by-turn list.  
1 In the map display, select “Options,then “Turns.”  
The turn-by-turn list appears.  
2 Select the desired item to show the detailed information.  
continue to next page r  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Viewing the entire route  
During route guidance, you can view the entire route to the destination.  
1 In the map display, select “Options,then “Turns.”  
2 Select “Confirm Route.”  
The entire route appears.  
To change the route calculation conditions  
1 Select “Change Condition,” then the desired option.  
Route guidance starts.  
Viewing a map of the vicinity of the destination  
During route guidance, you can view a map of the vicinity of the current destination.  
1 In the map display, select “Options,then “Turns.”  
2 Select “Show Destination.”  
A map of the vicinity of the current destination appears.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Destination management  
Destinations on “Recent Destinations,” “Address Book,” and “Favorites” can be managed.  
Recent destinations  
You can delete the history of “Recent Destinations.”  
1 In the menu display, touch  
2 Select “Delete.”  
, “My Places,then “Recent Destinations.”  
3 Select the item to delete.  
To select all items, select “All.”  
To unselect all items, select “Clear.”  
4 Select “Done,then “OK.”  
The selected item(s) is deleted.  
Address book  
You can register the destinations or points on the map to the address book.  
From the navigation menu  
1 In the menu display, touch  
, then select the desired search method.  
For details on search methods, see “Route searching” on page 13.  
You can select the desired search method, except for home search, address book search, and  
Favorites search.  
2 After setting the destination, select “Options” in the address/POI confirmation  
display.  
3 Select “Save This Location.”  
The registration display appears.  
continue to next page r  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
4 Set the following items.  
Item  
Purpose  
Name  
Group  
Enters the name.  
Selects the group to categorize.  
To create a new group, select “New Group,”  
then enter the group name.  
Phone  
Icon  
Enters the phone number.  
Selects the icon to show on the map.  
To select from the facility icon list, select  
“Facilities Icons” c category(ies) c icon.  
Sound  
Configures the sound setting.  
– “Sound Function”: Sets to “ON” to have  
notification sound upon approach.  
– “Sound Source”: Selects the sound source.  
– “Distance of Starting to Play Back”:  
Selects the distance at which the sound  
will be output.  
5 Select “Done.”  
The destination is added to the address book and indicated by the selected icon on the map.  
From the map option menu  
1 In the map display, touch the map to switch to the map scrolling mode, then  
select the desired point.  
2 Select “Options,then “More...”  
Follow the procedure from step 3 above to add the selected point to the address book.  
Tip  
Further management of address book is available from the setting menu (page 41).  
Favorites  
You can register destinations to “Favorite 1,” “Favorite 2,” “Favorite 3,” and “Favorite 4”  
separately.  
1 In the menu display, touch  
2 Select “Favorites.”  
, then “General.”  
3 Select “Favorite 1,Favorite 2,Favorite 3,or “Favorite 4.”  
4 Select the desired search method.  
For details on search methods, see “Route searching” on page 13.  
You can select the desired search method, except for Favorites search.  
5 After setting the destination, select “Done” in the address/POI confirmation  
display.  
The destination is stored in the selected Favorite.  
To change the registration in Favorites  
Follow the procedure above and overwrite a registered Favorite.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Photo Playback  
You can view photo files stored on a “Memory Stick Duo” inserted in the unit.  
Insert a “Memory Stick Duo” containing photo files shot by a Sony digital still camera in the  
unit.  
Supported photo file type  
File format  
JPEG  
File extension  
.JPG  
Number of pixels  
Max. 12 mega pixels  
Viewing photos  
1 In the menu display, touch  
The list of folders/files appears.  
To move to the upper level, touch  
, then “Photo.”  
.
To list files as thumbnails, select “Thumbnail.”  
2 Select the desired folder/file.  
If you select a folder, then select the desired file.  
The photo playback display appears with the selected photo file.  
continue to next page r  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Photo playback controls  
Touch the display if the photo playback controls are not shown.  
File name/shooting date and time  
1
2
3
4
5
6
7
1 To exit the photo browser.  
2 To select a file from the list.  
3 To skip to the previous file.  
4 To start the slideshow.  
5 To skip to the next file.  
6 To open the option menu for photo playback.  
7 To hide the playback controls.  
With Gesture Command  
In the photo playback display, draw one of the command strokes:  
– Start the slideshow (only when playback controls are shown): z  
– Skip to the previous file:  
– Skip to the next file:  
– Skip to the previous folder:  
– Skip to the next folder:  
Option menu for photo playback  
The following options for photo playback are available.  
Select “Opt.” in the tool bar, then one of the following items.  
Item  
Purpose  
Clockwise  
Rotates the current photo clockwise in 90  
degree steps.  
Counterclockwise  
Rotates the current photo counterclockwise in  
90 degree steps.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Photo settings  
The following photo settings are configurable.  
In the photo file list, select “Settings” c the desired item c the desired option.  
Item  
Purpose  
Playing Interval  
Repeat  
Sets the slideshow interval.  
Repeats the slideshow.  
Slideshow Range  
Plays slideshow of all photo files in a  
“Memory Stick Duo” or the currently selected  
folder.  
File Order  
Sorts photo files by shooting date or name.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Settings  
The setting menu includes the following categories.  
• “Route Planning” (page 40)  
• “Address Book” (page 41)  
• “General” (page 42)  
• “Map” (page 44)  
• “Route Profile” (page 45)  
• “Guide” (page 46)  
Route planning settings  
The following route planning settings are configurable.  
In the menu display, touch  
c “Route Planning” c the desired item c the desired option.  
Item  
Purpose  
Route Planning (page 28)  
Opens the route planning display to create an  
itinerary.  
Simulation  
Simulates the last route.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Address book settings  
The following address book settings are configurable.  
In the menu display, touch  
c “Address Book” c the desired item c the desired option.  
Item  
Purpose  
Edit Item  
Edits the address book entry.  
Select the group, then one of the following  
items.  
– Entry in the list: Opens the display where  
you can delete an entry, or change the name/  
group/phone/icon/sound setting.  
– “Move”: Categorizes entry(ies) to another  
group. Select the entry(ies) to move c  
“Move To” c the new group c “OK.”  
– “Delete”: Deletes an entry(ies). Select an  
entry(ies) to delete c “Done” c “OK.”  
Edit Groups  
Edits the group setting.  
– “New Group”: Creates a new group.  
– “Rearrange Group Order”: Changes the  
order of groups. Select the group c  
“Done.”  
/
c
– “Edit Group Name”: Changes the group  
name.  
– “Delete Group”: Deletes the group and all  
its entries.  
Make Backup  
Backs up the address book data on a  
“Memory Stick Duo.”  
Restore Address Book  
Import Items  
Restores the address book data from a  
“Memory Stick Duo.”  
Imports the address book entry(ies) from a  
“Memory Stick Duo.”  
Select the file in the “Memory Stick Duo” c  
all entries or individual entry c “Done” c  
“OK” c “OK.”  
Export Items  
Exports the address book entry(ies) to a  
“Memory Stick Duo.”  
Select the group c entry(ies) c “Done” c  
“Done” c “Done,” select/create a file, then  
select c “OK” c “OK.”  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
General settings  
The following settings related to the system are configurable.  
In the menu display, touch  
c “General” c the desired item c the desired option.  
Item  
Purpose  
Volume (Operation Sound)  
Presets the volume level for touch screen  
operation sound: “Level 3,” “Level 2,” “Level  
1,” “OFF.”  
Units  
Selects the distance unit: “Kilometers,”  
“Miles.”  
Time Format  
Selects the clock indication: “12hr (AM /  
PM),” “24hr.”  
Time Zone  
Select Language  
Display  
Sets the time zone automatically or manually.  
Selects the language for on-screen display.  
Adjusts the display settings.  
– “Brightness, Day / Night Mode”: Switches  
the display brightness automatically or sets  
the brightness for day time/night time use:  
“Automatic,” “Day,” “Night.” The  
brightness level for day time and night time  
use can be adjusted manually.  
– “Touchscreen Calibration”: Performs the  
touch screen calibration when the touch  
function is off the mark. Touch the targets in  
sequence.  
Input Home Address  
Registers your home address.  
– “Enter Address”: Sets from the navigation  
menu. For details on how to set the address,  
– “Map”: Selects on the map. For details on  
how to select the point on the map, see  
Start the Configuration Wizard  
Daylight Saving Time  
Configures the basic settings by following the  
wizard (i.e., to perform the Startup  
Configuration Wizard again).  
Sets daylight saving time automatically by  
GPS or manually.  
– “Automatic”: Updates automatically by  
GPS.  
– “Manual (+1h)”/“Manual (+30min)”: Sets  
manually.  
– “OFF”: Standard time.  
continue to next page r  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Item  
Purpose  
GUI Day / Night Mode  
Power Saving (Display OFF)  
Selects the color theme of menu displays.  
Turns off the display automatically after  
several minutes of inactivity: “ON,” “OFF.”  
Keyboard Style (page 9)  
Selects the keyboard type: “QWERTY +  
123,” “QWERTY,” “ABC.”  
Password Lock  
Locks the unit by setting a 4-digit numerical  
password to prevent unauthorized access:  
“ON,” “OFF.” Once activated, you will need  
to enter the password when you turn on the  
unit.  
To activate, select “ON,” enter the password,  
reenter the password to confirm, then select  
“OK.”  
To deactivate, select “OFF,” enter the  
password, then select “OK.”  
Change Password  
Changes the password for locking the unit.  
Enter the current password, enter the new  
password, then reenter the new password.  
Reset Factory Default  
Product Information  
Resets settings to default.  
Views the ID number and status (cradle  
connection, etc.) of the unit.  
GPS Status (page 12)  
Firmware Version  
Views the detailed GPS status information.  
Views the firmware version.  
Memory Stick Information  
Views the information of the currently  
inserted “Memory Stick Duo,” such as used/  
free space; formats the “Memory Stick Duo.”  
To format, select “Format” c “OK”  
repeatedly.  
Demonstration Mode  
– “Automatic Demonstration”: Sets to start  
the demonstration automatically after  
several minutes of inactivity: “ON,” “OFF.”  
– “Start Demonstration”: Starts the  
demonstration.  
Favorites (page 36)  
Registers destinations in Favorites.  
Track Log  
– “Store Track Log”: Logs your position at  
regular intervals while driving, and stores  
the data on a “Memory Stick Duo” inserted  
in the unit for later use on your computer,  
etc.  
– “Delete All Track Logs”: Deletes all track  
logs stored on a “Memory Stick Duo.”  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Map settings  
The following map display settings are configurable.  
In the menu display, touch  
c “Map” c the desired item c the desired option.  
Item  
Purpose  
2D / 3D Map View  
Selects the default map view.  
– “2D”: Overhead view.  
– “3D” (level 1): Aerial view (high angle).  
– “3D” (level 2): Aerial view (medium angle).  
– “3D” (level 3): Aerial view (low angle).  
Map Orientation  
Map Color  
Selects the default orientation of 2D map.  
– “In Direction of Travel”: Heading up.  
– “Always North”: North up.  
Selects the map color schemes for day time  
use and night time use.  
Automatic Map Color Change  
Switches the map color scheme automatically.  
Preset Scale (page 7)  
Presets the map scale level for clockwise and  
counterclockwise circles of Gesture  
Command.  
Landmark Icon  
Shows landmark icons on the map.  
The settings can be configured separately for  
each facility.  
Driving Trail  
Shows driving trail on the map: “ON,” “OFF.”  
Deletes driving trail.  
Delete Driving Trail  
Address Book Icon  
Shows the address book entry icons on the  
map: “ON,” “OFF.”  
Road Width  
Selects the width of the road shown on the  
map: “Wide,” “Standard.”  
Font Size  
Selects the size of the fonts shown on the  
map: “Large,” “Medium,” “Small.”  
Icon Size  
Selects the size of the icons shown on the  
map: “Large,” “Medium,” “Small.”  
Zoom While Scrolling  
Compass and Speedometer  
Zooms out the map/fixes the scale when  
scrolling: “ON,” “OFF.”  
Shows the current speed and direction on the  
map when no route guidance is in progress:  
“ON,” “OFF.”  
Map Version  
Views the version of the current map.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Route profile settings  
The following route profile settings are configurable.  
In the menu display, touch  
c “Route Profile” c the desired item c the desired option.  
Item  
Purpose  
Ferries  
Allows the use of ferries/avoids them unless  
no alternative is available: “Allow,” “Avoid.”  
Carpool Lanes  
Allows the use of carpool lanes/avoids them  
unless no alternative is available: “Allow,”  
“Avoid.”  
Driving Route History  
Calculation Condition  
Uses the driving route history when  
calculating the route: “Use,” “Not Use.”  
Sets the route calculation conditions.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Guidance settings  
The following route guidance settings are configurable.  
In the menu display, touch  
c “Guide” c the desired item c the desired option.  
Item  
Purpose  
Volume (Guide)  
Presets the volume level for voice guidance:  
“Level 3,” “Level 2,” “Level 1,” “OFF.”  
Voice Attention (Merge)  
Automatic Zoom  
Intersection Zoom  
Select Voice  
Activates the audio warning on merge: “ON,”  
“OFF.”  
Zooms out the map automatically when  
driving on the highway: “ON,” “OFF.”  
Shows the magnified view of an intersection:  
“ON,” “OFF.”  
Selects the guidance voice type.  
For details on how to import guidance voice  
data from your computer, see “Guidance  
To select the desired item, select the item c  
“Done.”  
To delete the item, select the item to delete c  
“Delete” c “OK.”  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Using the PC Application Software  
You can install the PC application software to your computer. Using the software, you can  
manage various data to use on the unit.  
System requirements  
Computer  
• IBM PC/AT compatible machines  
• USB port  
OS  
• Microsoft Windows 2000 Professional with Service Pack 4 (or later)  
• Microsoft Windows XP Home Edition/Professional with Service Pack 3 (or later)  
• Microsoft Windows XP Media Center Edition/Media Center Edition 2004/Media Center  
Edition 2005  
• Microsoft Windows Vista Home Basic/Home Premium/Business/Ultimate with Service Pack 1  
(or later)  
Monitor  
High color (16-bit color) or more, 800 × 600 dots or more  
Other  
Internet connection for data download and support  
Notes  
The following system environments are not supported.  
– Non IBM PC type computers, such as Macintosh, etc.  
– Homemade computers  
– OS upgraded computers  
– Multi-monitor environment  
– Multi-boot environment  
Depending on the computer condition, operation may not be possible even with the recommended  
environment.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing the software  
2 Enter your model number, then click “Continue.”  
3 Select “Drivers,then “nav-u tool” to download the software.  
4 Follow the instructions at the website and complete the installation.  
Connecting the unit to your computer  
1 Turn on the unit and your computer.  
2 Connect the unit to your computer with the USB cable.  
Note  
While using the software or transferring data, do not:  
– disconnect the USB cable.  
– turn off or reset the unit.  
– shut down the computer, enter computer standby mode, or restart the computer.  
Disconnecting  
After using the software or completing the transfer, exit the software, then disconnect the USB  
cable.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Starting the software  
1 Start the software.  
Click “start,” then select “(All) Programs” c “nav-u tool” c “nav-u tool.”  
The main menu appears.  
1
2
3
4
5
6
1 To manage guidance voice data (page 50).  
2 To manage the map data (page 51).  
3 To manage the address book data (page 52).  
4 To upgrade the firmware (page 54).  
5 To select the language for software on-screen displays.  
6 To access to the Sony navigation support site.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Guidance voice data management  
You can transfer guidance voice data from your computer to the unit, using the software.  
Before starting, connect the unit to your computer and start the software.  
You can also transfer data to the “Memory Stick Duo” inserted in the unit.  
1 Select “Guidance Voice Manager.”  
If the guidance voice data on your computer does not appear, select “Browse,” then specify  
the data location on your computer.  
2 Select the drive corresponding to the unit/“Memory Stick Duo.”  
3 In the list, check the box(es) of the guidance voice data to transfer, then select  
.
Transfer starts.  
4 Select “OK.”  
The guidance voice data is transferred to the unit/“Memory Stick Duo.”  
For details on how to select the transferred data on the unit, see page 46.  
Note  
In step 3 above, a notification appears if free space is insufficient on the unit/“Memory Stick Duo.” Delete  
unnecessary data by selecting “OK” c “Show” in “Target” c the data to delete c “Delete” c “OK” c “OK.”  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Map data management  
You can transfer and replace the map data on the unit, using the software (e.g., to restore map  
data if necessary).  
Before starting, connect the unit to your computer and start the software.  
1 Select “Map Manager.”  
If the map data does not appear, select “Browse,” then specify the data location.  
2 In the list, select the map to transfer, then  
.
3 Select “OK.”  
Transfer starts.  
4 Select “OK.”  
The map on the unit is replaced.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Address book data management  
Address book data on the unit or your computer can be managed, using the software. You can  
transfer or import the address book data on the unit or your computer.  
Editing the address book data on your computer  
You can edit the address book data on your computer, using the software.  
1 Select “Address Book Manager.”  
If the data does not appear in the list, select “Browse,” then specify the data location.  
2 Select  
.
3 Select the group/entry to edit, then the desired edit menu.  
Select  
Add  
To  
add a new group/entry.  
edit the selected group/entry.  
Edit  
4 Select “OK” after editing is complete.  
5 Select “Save item(s) to PC.”  
The address book data on the computer is updated.  
To delete the group/entry  
In step 3 above, select the group/entry to delete c “Delete” c “OK.”  
Editing the address book data on the unit  
You can edit the address book data on the unit, using the software.  
Before starting, connect the unit to your computer and start the software.  
1 Select “Address Book Manager.”  
2 Select  
.
the address book data on the unit, then select “Apply to the Unit.”  
continue to next page r  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Transferring address book data from your computer to the unit  
You can transfer address book data from your computer to the unit, using the software.  
Before starting, connect the unit to your computer and start the software.  
1 Select “Address Book Manager.”  
2 Select  
.
If the data does not appear in the list, select “Browse,” then specify the data location.  
3 Check the box(es) of the group(s)/entry(ies) on your computer.  
4 Select “Transfer including group name.or “Transfer only item(s).”  
5 Select “Transfer.”  
Transfer starts.  
6 Select “Apply to the Unit,then “OK.”  
The address book data is transferred to the unit.  
Note  
In step 5 above, a notification appears if free space is insufficient on the unit. Delete unnecessary address  
book data from the unit (page 52).  
Transferring address book data from the unit to your computer  
You can transfer address book data from the unit to your computer, using the software.  
Before starting, connect the unit to your computer and start the software.  
1 Select “Address Book Manager.”  
2 Select  
.
3 Check the box(es) of the group(s)/entry(ies) on the unit.  
4 Select “Save to PC.”  
5 Select “Save.”  
Transfer starts.  
6 Select “OK.”  
The address book data is transferred to your computer.  
Note  
In step 4 above, a notification appears if free space is insufficient on your computer. Delete unnecessary  
data from your computer.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Firmware upgrade  
You can upgrade the firmware on the unit, using the software.  
For details, visit the website below:  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Sennheiser Hearing Aid EK1010 User Manual
Shark Vacuum Cleaner EP602F User Manual
Sony Car Stereo System CDX R3350 User Manual
Sony DVD Recorder RDR HXD562 User Manual
Sony Home Theater System DX250 User Manual
Sony Stereo System CMT C5 User Manual
SpeakerCraft Printer PTJ 40 User Manual
Sprint Nextel Laptop S205s User Manual
Suncast Tool Storage RSH125 User Manual
Sylvania DVD VCR Combo SRD3900 User Manual