Dealer Setup
& Adjustment Instructions
520 Series Single Stage Snowthrower
This Dealer Setup Instruction applies to the following units:
These instructions may cover additional models issued after their printing.
Refer to the Dealer Setup Binder Index for complete listings.
520 Series Snowthrowers
Mfg. No. Description
7085663 SS5201R, 5HP Snowthrower, Manual Start
7085664 SS5201E, 5HP Snowthrower, Electric Start
1694585 5201M, 5HP Snowthrower, Manual Start
1694586 5201E, 5HP Snowthrower, Electric Start
ATTENTION SETUP PERSONNEL:
TABLE OF CONTENTS:
SAFETY RULES........................................................2
The safety warnings provided in this guide
and in the operator's manual included with
the unit contain important information that
SETUP PROCEDURES
must be obeyed when assembling, setting-up, operat-
ing, servicing, transporting, or storing the unit.
Quick Setup List.......................................................3
Unboxing and Assembly .........................................4
Fill Gas Tank.............................................................5
Fuel Oil Mix.............................................................5
Proper Fuel Mixing Procedure ................................5
Lubricate the Snowthrower.....................................6
These warnings are highlighted by the safety alert tri-
angle symbol shown above, which signifies that an
important safety message is being provided.
Removing the Belt Cover........................................6
Lubrication Points ...................................................6
Test Run....................................................................7
You must read, understand, and follow these warn-
ings and instructions, and use safe shop and work
practices at all times while working on or around
this unit and all other outdoor power equipment.
ADJUSTMENT PROCEDURES
Sections and items denoted by the Setup
symbol provide the information necessary to
fully assemble, test, and prepare the units
Removing Engine Cover..........................................8
Carburetor Adjustment............................................8
Servicing the Spark Plug.........................................8
Auger Control Cable Adjustment ...........................9
Checking the Adjustment........................................9
Adjusting the Cable.................................................9
described above for delivery to your customers.
A Quick Setup List is provided on page 3 of this
booklet to help you identify and check that the
items have been performed.
Testing the Auger Control Cable.............................9
Replacing the Drive Belt........................................10
Replacing the Scraper Blade ................................10
Manual No. 7100193
I.R. 6/10/2005
TP 300-5071-IR-SX-N
1
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Quick Setup List -
Page
Setup Procedure
Steps to Perform
❏ Remove Unit From Box.
4
Unbox & Assemble
❏ Install Discharge Chute
❏ Assemble Handle Bars
(Be careful not to pinch the auger cable)
❏ Mount Clean-Out Tool in storage position
on handle
5
6
7
Fill Gas Tank
❏ Fill Gas Tank
Lubricate Snowthrower
Test Run
❏ Lubricate all grease & oil points
❏ Check Primer
❏ Check Choke
❏ Check Recoil Starter
❏ Check Electric Starter (Where Applicable)
❏ Check Auger Control Cable
❏ Check Kill Switch
❏ Check Chute Rotator
❏ Check Deflector
Additional information concerning functional
tests, general adjustment procedures, and
the location of normal lubrication points are
included in these instructions.
Although all required lubrication and normal adjust-
ments on factory-assembled components are done at
the factory, this additional information is provided to
assist you in ensuring that each unit is delivered to the
customer in proper working order.
3
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
A
Unboxing & Assembly
1.Using a utility knife, open the box and remove the
snowthrower.
B
IMPORTANT NOTE
When removing the snowthrower
from the box and unfolding the han-
dle bars DO NOT PINCH THE AUGER
CONTROL CABLE IN THE HANDLE
BARS.
C
2. Install the discharge chute on to the rotating ring
located on the auger housing. Secure with the three
5/16 inch carriage bolts, flat washers and nylok nuts
found in the parts bag (the bolt heads go to inside
of of the rotating ring, with washers and nuts on the
outside). Refer to Figure 1.
NOTE: Install the rear bolt first for easier alignment.
3. Tighten bolts securely with a wrench.
Figure 2. Handles and Clean-out Tool
4. Lift up folding handle to align it with lower handle
and tighten the wing knobs securely as shown in
Figures 2 and 3.
A. Handle
B. Wing Knobs C. Clean-out Tool
5 Mount clean-out tool in storage position on handle.
Refer to Figure 2.
A
C
D
E
B
Figure 1. Assembly of Discharge Chute
Figure 3. Lift Handles and Lock Wing Knobs
A. Discharge Chute
B. Carriage Bolts
C. Washers
D. Nuts
E. Rotating Ring
4
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
FUEL TO OIL MIXTURE CHART (50:1)
U.S.
Imperial
Metric
Fill Gas Tank
Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil
Gallons
Ounces
2.5
5
Gallons
Ounces
Liters
Milliliters
Fuel and Oil Mixture
1
2
5
1
2
5
2.8
4
80 ml
The snowthrower uses a two cycle engine that requires
a mixture of fuel (gasoline) and oil for lubrication of
engine bearings and other moving parts.
5.6
8
160 ml
400 ml
13
14.1
20
The correct fuel/oil mixture ratio for the five horsepow-
er engine is 50 to 1. Use fuel/oil mixture chart shown.
NOTE: To prevent damage to engine, carefully
observe recommended fuel to oil mixing ratio and
procedures.
WARNING
• Gasoline and oil must be premixed in a clean fuel
container.
Gasoline is highly flammable and must be handled
with care. Never fill the tank when the engine is hot
or running. Always move outdoors to fill the tank.
Keep snowthrower and gasoline away from open
flame or spark.
• Always use fresh, unleaded, winter grade fuel
• Never put plain, unmixed fuel into fuel tank. Shake
fuel container each time before filling fuel tank.
• Never use “stale” fuel left over from last season or
stored for long periods.
• DO NOT USE MULTI VISCOSITY OILS, SUCH AS
10W-30 or 10W-40.
Proper Fuel Mixing Procedure
A
B
C
D
1. Fill approved clean fuel container one quarter full
with fresh unleaded fuel - one quart (one liter) in a
one gallon (4 liter) container.
2. Pour recommended amount of high quality two
cycle oil — 2.5 ounces (80 ml) into fuel container
for one gallon (4 liters) of fuel. (NOTE: DO NOT
USE MULTI VISCOSITY OILS, SUCH AS 10W-30
or 10W-40.)
3. Reinstall cap on the fuel container and shake con-
tainer vigorously so oil mixes with gasoline.
4. Unscrew cap and fill container with fuel. Shake
container again.
5. Remove fuel tank cap and carefully pour mixed fuel
into the fuel tank, filling to 1/2 inch (1.5 cm) below
filler neck to allow room for expansion. Never put
plain, unmixed fuel into fuel tank. Shake fuel
container each time before filling fuel tank.
Figure 4. Proper Fuel Mixing Procedure
A. Fill Container with 1 Quart (1 Liter) of fuel
B. 2.5 Ounces (80 ml) of two-cycle oil
C. Combine in container, then shake container
D. Additional fuel brings total to 1 Gallon (4 liters)
5
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Lubricate Snowthrower
Removing Belt Cover
Screws
In order to perform proper lubrication, it is necessary to
remove the Belt cover from the lower left of the
snowthrower.
1. Remove the Engine Key from the switch.
Figure 5. Removing Belt Cover
2. Remove the fours screws securing the belt cover
(see Figure 5).
3. Remove the cover.
4. Perform lubrication (see below).
5. Reinstall belt cover (reverse steps 3 to 1 above.)
Lubrication
Note: The drive pulley end of auger shaft is supported
by a sealed ball bearing and requires no lubrication.
The ball bearing on other end of auger shaft is also
sealed, and will not require lubrication.
Lightly Oil
• A few drops of oil should be placed on
wheel hubs occasionally to keep wheels
turning freely.
Figure 6. Lubrication points
• Apply oil to pivot points of auger control
periodically, wiping off any excess oil.
Pivot Point
• A couple of drops of light machine oil applied to
upper end of auger control cable will assure free
movement of cable through outside casing. Wipe
off any excess oil (Figure 5).
• Remove belt cover and lightly apply oil to the pivot
point for idler pulley arm. BE CAREFUL NOT TO
GET OIL ON BELT OR PULLEYS.
Figure 7. Lightly oil pivot point
Grease
• At the beginning of each snow throwing sea-
son, remove discharge chute, clean, and
generously lubricate steel flange at back of
rotating ring with light grease. Rotate ring
with crank to distribute grease (Figure 8).
Lubricate
Flange
Engine Lubrication
Figure 8. Grease the Discharge Chute Ring
The two cycle engine used in this snow thrower is lubri-
cated by the fuel and oil mixture. Observe recommend-
ed fuel to oil mixture ratio shown on page 5.
6
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Manual (Recoil) Starting Steps
1. Insert engine key in switch and turn key to the ON
position.
Test Run
2. If engine is cold, move choke control lever to the
ON position. (Do not choke a warm engine).
Test run the unit for several minutes. Check that the
following work properly:
3. Push the Primer Button two times if engine is cold.
(Do not prime a warm engine.)
• Primer
• Auger Control Cable
• Kill Switch
4. Grasp starter rope handle and slowly pull out rope
until resistance is felt. Allow rope to rewind slowly,
then pull rope out rapidly to start engine. Let rope
return slowly to starter.
• Choke
• Recoil Starter
• Chute Rotator
• Deflector
• Electric Starter
(Where Applicable)
NOTE: If engine does not start after three pulls,
push primer bulb once and again pull starter
rope.
STARTING THE ENGINE
NOTE: The snow thrower engine is designed to oper-
ate at cold temperatures. Avoid operating the snow
thrower if air temperature is (40° C or warmer since
engine may vapor lock and stop running after a short
time. Engine will be difficult to start in warm weather.
5. After engine starts and gradually warms up, move
choke lever to the OFF position. Be prepared to
move choke lever to the ON position if engine fal-
ters during warm up.
6. Allow engine to warm up before beginning snow
thrower operations. The engine will operate at full
throttle when thoroughly warmed up.
7. To stop engine, turn Engine Key to the OFF posi-
tion.
Electric Starting Steps
Note: The electric starter is designed to operate on
120V AC household current, using power cord supplied
with electric start snow thrower. When using power
cord, match wide blade of plug to wide slot of recepta-
cle.
STOPPING THE ENGINE
1. Release the Auger Control.
1. Insert engine key in switch and turn key to the ON
position.
2. Turn Engine Key to the OFF position.
2. If engine is cold, move choke control lever to the
ON position. (Do not choke a warm engine).
3. Remove the key from the switch if you are leaving
the operating position or will be making adjustments
or repairs. (NOTE: Allow the unit to cool before stor-
ing or making any adjustments or repairs.)
3. Push the Primer Button two times if engine is cold.
(Do not prime a warm engine.)
4. Plug power cord for starter into receptacle on
starter switch, then plug other end into a 120Volt
AC household receptacle. DO NOT use an exten-
sion cord with the electric start power cord supplied.
OPERATING THE SNOWTHROWER
Before operating snowthrower, review the Checks
Before Each Use under General Operation on page 8
of this manual.
5. Push starter button to crank engine. DO NOT crank
engine for more than a total of 15 seconds without
allowing electric starter to cool for 10 minutes
before additional cranking is attempted. Electric
starter can be severely damaged if recommended
starter operating limitations are not observed.
1. Rotate the discharge chute to the desired direction.
2. Pull the Auger Control back against the handle to
engage the auger and tip the unit slightly forward.
NOTE: The snow thrower will be pulled forward by
the auger when the auger contacts the ground or
with the snow to be thrown.
NOTE: Do not push primer button while engine
is being cranked.
6. Release starter button when engine starts and
gradually move choke lever to the OFF position.
3. Begin snow removal by clearing a path down the
center of walk or driveway, then gradually widen
path, throwing snow off to both sides.
7. Disconnect power cord from household receptacle
and then from starter switch on snow thrower. Store
cord in a dry, convenient place.
4. Release the Auger Control to stop both the auger
and the forward motion of the snowthrower.
NOTE: Always disconnect power cord from
household receptacle first, then unplug from
starter switch.
8. To stop engine, turn Engine Key to the OFF posi-
tion.
7
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Removing
Remove
Fuel Tank
Cap
Engine Cover
Note: In many of the following adjustment and service
tasks, it will be necessary to remove and reinstall the
engine cover. To remove the cover, proceed as fol-
lows:
1. Remove the Engine Key from the switch.
2. Remove the two rear fasteners securing the back
of the cover housing. (Figure 9).
3. Remove the fuel tank cap.
4. Remove the cover (see Figure 10).
5. Temporarily reinstall the fuel tank cap.
6. Perform the adjustments or service desired.
7. Reinstall the cover by reversing the removal steps.
Remove two
rear fasteners
securing
cover
Note: The tabs at the lower front of the cover must
be positioned correctly.
Figure 9. Remove and/or loosen Cover Screws
WARNING
To avoid the possibility of serious bodily injury when
performing adjustments, maintenance or lubrication,
stop engine and remove key from switch.
Lift Cover
from Rear
of unit
Carburetor
Adjustment
The carburetor is properly calibrated and preset at the
factory for efficient cold weather operation. There are
no adjusting screws on the carburetor.
Insert front
tabs first
when
reinstalling
cover.
Align rear
tabs & side of
cover when
reinstalling.
If it is apparent that the carburetor is not providing sat-
isfactory fuel supply to engine, contact your nearest
Authorized Tecumseh Service Outlet for service.
Figure 10. Cover Removal & Installation
Servicing
the Spark Plug
1. Remove Engine Key from switch.
2. Remove the engine cover. (See procedure above.)
3. Disconnect the wire from the spark plug.
4. Inspect the Spark Plug and clean. If necessary,
replace the it with a new Spark Plug as recom-
mended in the Engine Owners Manual.
Spark Plug
Wire
5. Adjust the gap on the Spark Plug to .030 inches
(.762 mm) using a gauge.
6. Reinstall the plug and tighten firmly.
7. Reconnect Spark Plug wire.
8. Reinstall engine cover.
Figure 11. Servicing Spark Plug
8
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Auger Control Cable
Adjustment
Locknuts
Spring
The length of the auger control cable is adjustable.
However, it will seldom be necessary to change the
cable length since the operating tension on the drive
belt is maintained by the spring on the end of the cable.
If the auger turns too slowly under heavy load or
momentary squealing of drive belt is heard when enter-
ing heavy snow, pressure applied to drive belt by idler
pulley must be increased by reducing the slack in the
cable.
If the auger continues to turn when the auger con-
trol is released, the cable is too tight. The pressure
applied to the drive belt must be eliminated by increas-
ing the amount of slack to the cable adjustment.
Figure 12. Auger Control Cable
Checking the Adjustment
WARNING
1. Remove the Cover. (See Figures 9 & 10.)
Use extreme care when making adjust-
ments that require engine to be running.
Keep hands, feet, hair and loose clothing
away from any moving parts.
2. Measure the spring while the auger control on the
handle is disengaged. Record this measurement.
3. Pull the auger control against the handle and again
measure the spring. Record this measurement.
4. Compare the two measurements. The measure-
ment obtained with the spring extended should be
7/16 inch (11 mm) greater than with the spring un-
extended.
WARNING
Adjusting the Cable
Make certain the cable is NOT placing any ten-
sion on the spring. If the cable places tension on
the spring, the auger may turn when the control
has not been engaged.
1. Remove the engine cover.
2. Locate and loosen the lower locknut securing the
auger control cable (shown in Figure 12).
3. To change the slack in the cable, turn the upper
locknut slightly just until the slack between the
spring and the exposed cable has been elimi-
nated.
4. Tighten the lower locknut.
5. Reinstall the engine cover.
6. Test the units to make certain that the cable has
been adjusted properly (see “Testing the Auger
Control Cable “ below).
Testing the Auger Control Cable
Start the snow thrower engine and pull back on auger
control to operate auger. Release auger control and
check to be sure auger stops turning.
If auger continues to turn after auger control is
released, the cable is too tight and will have to be
adjusted to make it longer. Cable must be slightly
slack when auger control is released (away from
handle).
9
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Service Notes
10
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Service Notes
11
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
520 Single Stage Snowthrower
Replacing
the Drive Belt
1. Remove Engine Key from switch.
2. Remove belt cover (see Page 6) and the engine
cover (see Page 8).
3. Move the Auger Control on the handle and slip the
belt out from between the brake lever and roller
and away from the idler pulley.
Idler
Pulley
Engine
Pulley
4. Remove the belt from the engine and auger pul-
leys.
5. Install new belt around engine and auger pulleys
and under idler pulley. The ribbed side of the belt
must be to the inside, against auger and engine
pulleys.
6. Slip the new belt into place between brake lever
and roller.
Brake
Lever/Roller
7. Start the engine and engage/disengage the auger
control several times. Make certain that auger
stops turning within 5 seconds after the control is
released.
Drive Belt
Auger Pulley
8. If the auger does not stop turning within 5 second
after the control is released, adjust the tension on
the control cable by following the Adjusting Control
Cable procedure in the adjustments section of this
manual.
Figure 13. Drive Belt Replacement
9. Reinstall the belt and engine covers.
Replacing
the Scraper Blade
1. Remove Engine Key from switch.
2. Remove the two bolts and nuts securing the
Scraper Blade to the auger housing. (Retain the
bolts and nuts for attaching the new blade.)
3. Remove the worn Scraper Blade.
4. Install the new Scraper Blade and secure it with the
three bolts and nuts saved in step 2 above.
Scraper Blade, Bolts & Nuts
Figure 14. Removing Scraper Blade
PRODUCTS, INC.
McDonough, GA., 30253
MANUFACTURING INC.
© Copyright 2005 Simplicity Manufacturing, Inc.
All Rights Reserved. Printed in USA
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
Manual No. 7100193
I.R. 6/10/2005
TP 300-5071-IR-SX-N
12
5/2005
Download from Www.Somanuals.com. All Manuals Search And Download.
|