Clean-Out Tool Kit
Installation
Part No. 1687099
319 / 520 / 551 Single Stage, 5-13 HP
Instructions
Intermediate or Large Frame Snowthrowers
3
Kit Contents:
Ref. Part No. Qty. Description
1
2
3
4
5
6
7
8
9
1733209
1726727
1726728
1726995
1678392
1960727
1960589
1933896
1960729
1
1
1
1
1
1
1
1
1
1
1
1
CLEAN-OUT TOOL
BRACKET, Lower
CLIP
5
4
11
SPACER, 1-1/4” Long
SPACER, 11/32” Long
SCREW, Slotted, 10-24 x 2-1/2
SCREW, Phillips Head, 10-24 x 3/4
NUT, Nylock, 10-24
CAPSCREW, 5/16-18 x 1
CAPSCREW, 5/16-18 x 2
DECAL, Danger
1
10
7
6
9
10 1960730
11 7071880
12 1931338
8
12
Carriage Bolt, 5/16-18 x 1-3/4
2
Figure 1. Contents
CLEARING A CLOGGED DISCHARGE
CHUTE
Hand contact with the rotating impeller inside the dis-
charge chute is the most common cause of injury associ-
ated with snowthrowers. Never use your hand to clean
out the discharge chute.
This kit is to install a clean-out tool on a variety of
snowthrowers.
WARNING
Before beginning any service work turn off
ignition, and disconnect the spark plug wire.
To clear the chute:
1. SHUT OFF THE ENGINE.
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
GENERAL OPERATION
After installation of the clean-out tool kit, make sure
clean-out tool is attached to handle on machine. Do not
operate the machine without the clean-out tool properly
stored on the handle.
3. Always use a clean out tool, not your hands.
DANGER
Do not clean out discharge chute with hands.
Contact with moving parts inside chute will
cause serious injury. Use clean out tool provided
with machine. Use the following procedure to
remove objects or clear the chute:
Upon completion of installation of clean-out tool, keep
these instructions and warnings with the Operator’s
Manual.
Note: For proper use of clean-out tool it may be neces-
sary on some models to remove the wire guard from the
chute.
1. Stop the engine. Remove the key
2. Wait 10 seconds to be sure the auger/impeller
blades have stopped rotating.
3. Always use the clean-out tool. DO NOT use your
hands.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clean-Out Tool Kit
Installation Instructions
(TUBE HANDLE MODELS)
1. Remove existing hardware (A, Figure 5) from upper
hole on left side handle (C) as shown. Discard cap-
screw (D).
C
A
2. Using square hole install lower bracket (B) into upper
hole on left side handle (C) as shown. Secure with
new 5/16-18 x 2 capscrew (D) and nut (A).
Note: In some cases the upper hole in the left side han-
dle is crimped flat. If so use 5/16-18 x 1 capscrew (D).
D
A
3. Measure 16-3/8” from top of bracket (A, Figure 6) to
center of handle (B). Center punch and drill a new
13/64 hole (B) in handle (H).
B
4. Attach clip (D) to handle (H) securing with #10-24 x
2-1/2 screw (E), 1-1/4” spacer (C), and #10-24 lock-
nut (F) mounting through new hole (B).
Figure 5. Mounting Lower Bracket (Tube Handle)
A. Existing Hardware
B. Lower Bracket
C. Handle, LH
D. Capscrew
5. Attach clean out tool (G) to handle (H) by first placing
pointed end into bracket (A), then pushing hand grip
into clip (D).
6. Read and follow warnings when using the clean-out
tool.
F
B
C
D
E
16-3/8”
H
G
A
Figure 6. Mounting Clean-Out Tool (Tube Handle)
A. Bracket
F. Locknut, #10-24
G. Clean-Out Tool
H. Handle, LH
B. New Hole, 13/64”
C. Spacer, 1-1/4”
D. Clip
E. Screw, Slotted, #10-24 x 2-1/2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Clean-Out Tool Kit
D
B
F
A
B
E
C
C
D
E
H
Figure 7. Mounting Lower Bracket (520)
15-3/8”
A. Wing Lock Knob
B. Lower Bracket
C. Screw, Curved Head
D. Handle, LH
E. Carriage Bolt,
5/16-18 x 1-3/4
G
(520 MODELS)
1. Remove wing lock knob (A, Figure 7) and carriage
bolt (E) or screw (C) from hole on left side handle (D)
as shown. Discard screw (C) if it was used originally.
A
2. Using square hole install lower bracket (B) into hole
on left side handle (D) as shown. Secure with existing
or new 5/16-18 x 1-3/4 carriage bolt (E) and wing lock
knob.
Figure 8. Mounting Clean-Out Tool (520)
A. Bracket
F. Locknut, #10-24
G. Clean-Out Tool
H. Handle, LH
3. Measure 15-3/8” from top of bracket (A, Figure 8) to
center of handle (B). Center punch and drill a new
13/64 hole (B) in handle (H).
B. New Hole, 13/64”
C. Spacer, 1-1/4”
D. Clip
E. Screw, Slotted, #10-24 x 2-1/2
4. Attach clip (D) to handle (H) securing with #10-24 x
2-1/2 screw, 1-1/4” spacer (C), and #10-24 locknut
(F) mounting through new hole (B).
B
5. Attach clean out tool (G) to handle (H) by first placing
pointed end into bracket (A), then pushing hand grip
into clip (D).
A
B
C
C
6. Read and follow warnings when using the clean-out
tool.
C
(319 MODELS)
B
Mount to right hand side handle of unit following the
same instructions for the 520 models. Rotate position of
new clean-out hole (B, Figure 9) approximately 30
degrees from existing bail hole (C) to avoid interference
of bail operation.
A
Top View
Cross Section View
Figure 9. Hole Location 319 Models
A. Handle
C. Existing Bail Hole
B. New Clean-Out Tool Hole
Form No. 1727771-02
Rev. 01/2007
TP 200-4147-02-SK-SN
MANUFACTURING, INC.
Briggs & Stratton Yard Power Products Group
Copyright © 2007 Briggs & Stratton Corporation
Milwaukee, WI USA. All Rights Reserved
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|