Sharp Projector XR 32X User Manual

DATA PROJECTOR  
MODEL  
XR-32X  
XR-32S  
OPERATION MANUAL  
XR-32X  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIAL NOTE FOR USERS IN THE U.K.  
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-  
ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362  
fuse marked or  
and of the same rating as above, which is also indicated on the pin  
face of the plug, must be used.  
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse  
cover fitted.  
In the unlikely event of the socket outlet in your home not being compatible with the plug  
supplied, cut off the mains plug and fit an appropriate type.  
DANGER:  
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-  
ately and disposed of in a safe manner.  
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket  
outlet, as a serious electric shock may occur.  
To fit an appropriate plug to the mains lead, follow the instructions below:  
WARNING:  
THIS APPARATUS MUST BE EARTHED.  
IMPORTANT:  
The wires in this mains lead are coloured in accordance with the following code:  
Green-and-yellow : Earth  
Blue  
Brown  
: Neutral  
: Live  
As the colours of the wires in the mains lead of this apparatus may not correspond with the  
coloured markings identifying the terminals in your plug proceed as follows:  
The wire which is coloured green-and-yellow must be connected to the terminal in the  
plug which is marked by the letter E or by the safety earth symbol or coloured green or  
green-and-yellow.  
The wire which is coloured blue must be connected to the terminal which is marked with  
the letter N or coloured black.  
The wire which is coloured brown must be connected to the terminal which is marked with  
the letter L or coloured red.  
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The supplied CD-ROM contains operation instructions in English, German, French,  
Spanish, Italian, Dutch, Swedish, Portuguese, Chinese and Korean. Carefully read  
through the operation instructions before operating the projector.  
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,  
Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch und Koreanisch.  
Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.  
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand,  
français, espagnol, italien, néerlandais, suédois, portugais, chinois et coréen. Veuillez lire  
attentivement ces instructions avant de faire fonctionner le projecteur.  
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska,  
franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska och koreanska.  
Läs noga igenom bruksanvisningen innan projektorn tas i bruk.  
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán,  
francés, español, italiano, holandés, sueco, portugués, chino y coreano. Lea  
cuidadosamente las instrucciones de operación antes de utilizar el proyector.  
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese,  
spagnolo, italiano, olandese, svedese, portoghese, cinese e coreano. Leggere  
attentamente le istruzioni per l’uso prima di usare il proiettore.  
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans,  
Italiaans, Nederlands, Zweeds, Portugees, Chinees en Koreaans. Lees de handleiding  
zorgvuldig door voor u de projector in gebruik neemt.  
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,  
Espanhol, Italiano, Holandês, Sueco, Português, Chinês e Coreano. Leia  
cuidadosamente todas as instruções de operação antes de operar o projetor.  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using the projector, please read this operation manual carefully.  
Introduction  
ENGLISH  
There are two important reasons for prompt warranty registration of your new SHARP  
Projector, using the REGISTRATION CARD packed with the projector.  
1. WARRANTY  
This is to assure that you immediately receive the full benefit of the parts, service  
and labor warranty applicable to your purchase.  
2. CONSUMER PRODUCT SAFETY ACT  
To ensure that you will promptly receive any safety notification of inspection,  
modification, or recall that SHARP may be required to give under the 1972  
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT  
“LIMITED WARRANTY” CLAUSE.  
U.S.A. ONLY  
WARNING: High brightness light source. Do not stare into the beam of light, or view  
directly. Be especially careful that children do not stare directly into the  
beam of light.  
WARNING: To reduce the risk of fire or electric shock, do not expose  
this product to rain or moisture.  
See bottom of projector.  
The lightning flash with arrowhead sym-  
bol, within an equilateral triangle, is in-  
tended to alert the user to the presence  
of uninsulated “dangerous voltage”  
within the product’s enclosure that may  
be of sufficient magnitude to constitute  
a risk or electric shock to persons.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE SCREWS  
EXCEPT SPECIFIED USER  
SERVICE SCREW.  
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER.  
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
The exclamation point within a triangle  
is intended to alert the user to the  
presence of important operating and  
maintenance (servicing) instructions in  
the literature accompanying the product.  
WARNING: FCC Regulations state that any unauthorized changes or modifications to  
this equipment not expressly approved by the manufacturer could void  
the user’s authority to operate this equipment.  
U.S.A. ONLY  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
INFORMATION  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation. This equipment generates,  
uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the operation manual, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception, which can  
be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and the receiver.  
• Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
U.S.A. ONLY  
• Consult the dealer or an experienced radio/TV technician for help.  
Declaration of conformity  
SHARP PROJECTOR, MODEL XR-32X/XR-32S  
This device complies with Part 15 of the FCC rules. Operation is subject to the following  
conditions: (1) This device may not cause harmful interference, and (2) this device must  
accept any interference received, including interference that may cause undesired operation.  
Responsible Party:  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07430-2135  
TEL: 1-800-BE-SHARP (1-800-237-4277)  
U.S.A. ONLY  
PRODUCT DISPOSAL  
This product utilizes tin-lead solder, and lamp containing a small amount  
of mercury. Disposal of these materials may be regulated due to  
environmental considerations. For disposal or recycling information,  
please contact your local authorities, the Electronics Industries Alliance:  
or Sharp at 1-800-BE-SHARP.  
U.S.A. ONLY  
Caution Concerning Lamp Replacement  
See “Replacing the Lamp” on page 52.  
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 (XR-  
32X)/480,000 (XR-32S) pixels (micromirrors). As with any high technology electronic equipment  
such as large screen TVs, video systems and video cameras, there are certain acceptable  
tolerances that the equipment must conform to.  
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots  
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.  
Authorized representative responsible for the European Union Community Market  
SHARP ELECTRONICS (Europe) GmbH  
E.U. ONLY  
Sonninstraße 3, D-20097 Hamburg  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Read this Operation Manual  
The specifications are slightly different, depending on the model. However, you can connect and  
operate all models in the same manner.  
In this operation manual, the illustration and the screen display are simplified for explanation, and  
may differ slightly from the actual display. The examples used throughout this manual are based  
on the XR-32X model.  
Using the Menu Screen  
ENTER button  
Adjustment buttons (P/R/O/Q)  
MENU/HELP button  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
Buttons used in  
this operation  
RETURN button  
• Press RETURN to return  
to the previous screen  
when the menu is  
displayed.  
MENU/HELP button  
Menu Selections (Adjustments)  
Example: Adjusting “Bright”.  
Button used in  
this step  
• This operation can also be performed by using the buttons on the projector.  
Example: “Picture” screen menu for  
COMPUTER (RGB) input  
Press MENU/HELP.  
1
2
• The “Picture” menu screen for the se-  
lected input mode is displayed.  
Menu item  
Press Q or O and select “Picture”  
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
to adjust.  
Picture Mode  
Contrast  
Bright  
0
0
0
0
0
1
Red  
On-screen  
display  
Blue  
CLR Temp  
Bright Boost  
C.M.S. Setting  
C.M.S.  
On  
DNR  
Off  
Lamp Setting  
Reset  
Bright  
SEL./ADJ.  
ENTER  
END  
38  
Info  
Note  
........Indicates safeguards for using the projector.  
.........Indicates additional information for setting up and operating the  
projector.  
For Future Reference  
Maintenance  
Troubleshooting  
Index  
P. 49  
PP. 63 and 64  
P. 68  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Preparing  
Introduction  
Useful Features  
How to Read this Operation Manual .... 3  
Contents ............................................... 4  
IMPORTANT SAFEGUARDS ............... 6  
How to Access the PDF Operation  
Manuals .............................................. 9  
Accessories ........................................ 10  
Part Names and Functions ................. 11  
Projector ............................................... 11  
Rear View ............................................. 12  
Inserting the Batteries .......................... 14  
Usable Range ...................................... 15  
Operating with the Remote Control.... 32  
Displaying and Setting the  
Break Timer........................................ 32  
Displaying the Pointer .......................... 32  
Using the Spot Function ...................... 32  
Switching the Eco+Quiet Mode ........... 32  
Auto Sync (Auto Sync Adjustment) ..... 33  
Freezing a Moving Image .................... 33  
Selecting the Picture Mode .................. 33  
Displaying an Enlarged Portion of  
an Image ............................................ 33  
Using the Remote Control as the  
Wireless Computer Mouse ................ 34  
Menu Items ......................................... 35  
Using the Menu Screen ...................... 38  
Menu Selections (Adjustments) ........... 38  
Picture Adjustment (“Picture” Menu) ... 40  
Selecting the Picture Mode .................. 40  
Adjusting the Image ............................. 41  
Adjusting the Color Temperature ......... 41  
Adjusting the Colors............................. 41  
Progressive ........................................... 42  
Reducing Image Noise (DNR) ............. 42  
Lamp Setting ........................................ 42  
Adjusting the Projector Image  
(“SCR - ADJ” Menu) ......................... 43  
Setting the Resize Mode ...................... 43  
Adjusting the Image Position ............... 43  
Keystone Correction ............................ 43  
Setting the On-screen Display ............. 43  
Closed Caption .................................... 44  
Selecting the Background Image ........ 44  
Selecting the Setup Guide ................... 44  
Reversing/Inverting Projected  
Quick Start  
Quick Start .......................................... 16  
Setup and Projection ............................ 16  
Setup  
Setting up the Projector ...................... 18  
Setting up the Projector ....................... 18  
Standard Setup (Front Projection) ....... 18  
Ceiling-mount Setup ............................ 18  
Projection (PRJ) Mode ......................... 19  
Screen Size and Projection Distance .. 20  
Connections  
Connecting the Projector to  
Other Equipment .............................. 21  
Controlling the Projector by  
a Computer....................................... 24  
Connecting the Power Cord ............... 24  
Images ............................................... 44  
Selecting the On-screen Display  
Language........................................... 44  
Adjusting the Projector Function  
Using  
(“PRJ - ADJ” Menu) .......................... 45  
Auto Sync (Auto Sync Adjustment) ..... 45  
Auto Power Off Function ...................... 45  
Auto Restart Function .......................... 45  
STANDBY Mode ................................... 45  
Setting the Confirmation Sound  
Basic Operation  
Turning the Projector On/Off .............. 25  
Turning the Projector on ....................... 25  
Turning the Power off (Putting the  
Projector into Standby Mode) ........... 25  
Image Projection................................. 26  
About the Setup Guide ........................ 26  
Adjusting the Projected Image ............ 26  
Correcting Trapezoidal Distortion ........ 28  
Switching the Input Mode .................... 29  
Adjusting the Volume ........................... 29  
Displaying the Black Screen and  
(System Sound) ................................. 45  
Speaker Setting .................................... 45  
Audio Input ........................................... 46  
Selecting the Transmission Speed  
(RS-232C) .......................................... 46  
Fan Mode Setting ................................. 46  
System Lock Function .......................... 46  
Checking the Lamp Life Status ........... 47  
Keylock Function .................................. 47  
Turning off the Sound Temporarily .... 29  
Resize Mode......................................... 30  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting with the  
“Help” Menu ...................................... 48  
Utilizing the “Help” Menu Functions .... 48  
Reference  
Appendix  
Maintenance ....................................... 49  
Maintenance Indicators ...................... 50  
Regarding the Lamp ........................... 52  
Lamp..................................................... 52  
Caution Concerning the Lamp ............ 52  
Replacing the Lamp ............................. 52  
Removing and Installing the  
Lamp Unit .......................................... 53  
Resetting the Lamp Timer.................... 54  
Connecting Pin Assignments ............. 55  
RS-232C Specifications and  
Commands ....................................... 57  
Computer Compatibility Chart ............ 62  
Troubleshooting .................................. 63  
For SHARP Assistance ...................... 65  
Specifications ..................................... 66  
Dimensions ......................................... 67  
Index ................................................... 68  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
CAUTION:Please read all of these instructions before you operate this product  
and save these instructions for later use.  
Electrical energy can perform many useful functions. This product has been engineered  
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN  
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the  
safeguards incorporated in this product, observe the following basic rules for its installation,  
use and servicing.  
1. Read Instructions  
10. Ventilation  
Slots and openings in the cabinet are provided  
All the safety and operating instructions should  
be read before the product is operated.  
for ventilation to ensure reliable operation of the  
product and to protect it from overheating, and  
these openings must not be blocked or covered.  
The openings should never be blocked by placing  
the product on a bed, sofa, rug, or other similar  
surface. This product should not be placed in a  
built-in installation such as a bookcase or rack  
unless proper ventilation is provided or the  
manufacturer’s instructions have been adhered  
to.  
2. Retain Instructions  
The safety and operating instructions should be  
retained for future reference.  
3. Heed Warnings  
All warnings on the product and in the operating  
instructions should be adhered to.  
4. Follow Instructions  
All operating and use instructions should be  
followed.  
11. Power Sources  
5. Cleaning  
This product should be operated only from the  
type of power source indicated on the marking  
label. If you are not sure of the type of power  
supply to your home, consult your product dealer  
or local power company. For products intended  
to operate from battery power, or other sources,  
refer to the operating instructions.  
Unplug this product from the wall outlet before  
cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning.  
6. Attachments  
Do not use attachments not recommended by the  
product manufacturer as they may cause hazards.  
12. Grounding or Polarization  
This product is provided with one of the following  
types of plugs. If the plug should fail to fit into the  
power outlet, please contact your electrician.  
Do not defeat the safety purpose of the plug.  
a. Two-wire type (mains) plug.  
7. Water and Moisture  
Do not use this product near water–for example,  
near a bath tub, wash bowl, kitchen sink, or  
laundry tub; in a wet basement; or near a  
swimming pool; and the like.  
8. Accessories  
b. Three-wire grounding type (mains) plug with  
a grounding terminal.  
Do not place this product on an unstable cart,  
stand, tripod, bracket, or table. The product may  
fall, causing serious injury to a child or adult, and  
serious damage to the product. Use only with a  
cart, stand, tripod, bracket, or table  
recommended by the manufacturer, or sold with  
the product. Any mounting of the product should  
follow the manufacturer’s instructions, and should  
use a mounting accessory recommended by the  
manufacturer.  
This plug will only fit into a grounding type  
power outlet.  
13. Power-Cord Protection  
Power-supply cords should be routed so that they  
are not likely to be walked on or pinched by items  
placed upon or against them, paying particular  
attention to cords at plugs, convenience  
receptacles, and the point where they exit from  
the product.  
9. Transportation  
14. Lightning  
A
product and cart  
For added protection for this product during a  
lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from  
the wall outlet and disconnect the cable system.  
This will prevent damage to the product due to  
lightning and power-line surges.  
combination should be  
moved with care. Quick  
stops, excessive force,  
and uneven surfaces may  
cause the product and cart  
combination to overturn.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. Overloading  
19. Replacement Parts  
Do not overload wall outlets, extension cords, or  
integral convenience receptacles as this can  
result in a risk of fire or electric shock.  
When replacement parts are required, be sure  
the service technician has used replacement  
parts specified by the manufacturer or have the  
same characteristics as the original part.  
Unauthorized substitutions may result in fire,  
electric shock, or other hazards.  
16. Object and Liquid Entry  
Never push objects of any kind into this product  
through openings as they may touch dangerous  
voltage points or short-out parts that could result  
in a fire or electric shock. Never spill liquid of any  
kind on the product.  
20. Safety Check  
Upon completion of any service or repairs to this  
product, ask the service technician to perform  
safety checks to determine that the product is in  
proper operating condition.  
17. Servicing  
Do not attempt to service this product yourself as  
opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all  
servicing to qualified service personnel.  
21. Wall or Ceiling Mounting  
This product should be mounted to a wall or  
ceiling only as recommended by the  
manufacturer.  
18. Damage Requiring Service  
Unplug this product from the wall outlet and refer  
servicing to qualified service personnel under the  
following conditions:  
22. Heat  
This product should be situated away from heat  
sources such as radiators, heat registers, stoves,  
or other products (including amplifiers) that  
produce heat.  
a. When the power-supply cord or plug is  
damaged.  
b. If liquid has been spilled, or objects have fallen  
into the product.  
c. If the product has been exposed to rain or  
water.  
d. If the product does not operate normally by  
following the operating instructions. Adjust only  
those controls that are covered by the  
operating instructions, as an improper  
adjustment of other controls may result in  
damage and will often require extensive work  
by a qualified technician to restore the product  
to normal operation.  
e. If the product has been dropped or damaged  
in any way.  
f. When the product exhibits a distinct change  
in performance, this indicates a need for  
service.  
• DLP® and the DLP logo are registered trademarks of Texas Instruments.  
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United  
States and/or other countries.  
• PC/AT is a registered trademark of International Business Machines Corporation in the  
United States.  
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.  
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or  
other countries.  
• All other company or product names are trademarks or registered trademarks of their  
respective companies.  
• Some IC chips in this product include confidential and/or trade secret property belonging  
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,  
reverse engineer, reverse assemble or discompile the contents thereof.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Observe the following safeguards when setting up your  
projector.  
Caution concerning the lamp unit  
Potential hazard of glass par-  
ticles if lamp ruptures.In case  
of lamp rupture, contact your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center for replacement.  
When using the projector in high-altitude  
areas such as mountains (at altitudes of  
approximately 1,500 meters (4,900 feet)  
or more)  
When you use the projector in high-altitude  
areas with thin air, set “Fan Mode” to “High”.  
Neglecting this can affect the longevity of the  
optical system.  
See “Replacing the Lamp” on  
page 52.  
Warning about placing the projector in  
a high position  
When placing the projector in a high position,  
make certain it is carefully secure to avoid  
personal injury caused by the projector fall-  
ing down.  
Caution concerning the setup of the  
projector  
For minimal servicing and to maintain high  
image quality, SHARP recommends that this  
projector be installed in an area free from  
humidity, dust and cigarette smoke.When the  
projector is subjected to these environments,  
the vents and lens must be cleaned more of-  
ten. As long as the projector is regularly  
cleaned, use in these environments will not  
reduce the overall operation life of the unit.  
Internal cleaning should only be performed  
by a Sharp Authorized Projector Dealer or  
Service Center.  
Do not subject the projector to hard  
impact and/or vibration.  
Protect the lens so as not to hit or damage  
the surface of the lens.  
Rest your eyes occasionally.  
Continuously watching the screen for long  
hours will cause eye strain. Take regular  
breaks to rest your eyes.  
Do not set up the projector in places  
exposed to direct sunlight or bright light.  
Position the screen so that it is not in direct  
sunlight or room light. Light falling directly on  
the screen washes out the colors, making  
viewing difficult. Close the curtains and dim  
the lights when setting up the screen in a  
sunny or bright room.  
Avoid locations with extremes of  
temperature.  
The operating temperature of the projector is  
from 41°F to 95°F (+5°C to +35°C).  
The storage temperature of the projector is  
from –4°F to 140°F (–20°C to +60°C).  
Do not block the exhaust and intake  
vents.  
Caution regarding placing of the projector  
Place the projector on a level site within the  
adjustment range (9 degrees) of the adjust-  
ment foot.  
Allow at least 11 13/16 inches (30 cm) of space  
between the exhaust vent and the nearest  
wall or obstruction.  
Ensure that the intake vent and the exhaust  
vent are not obstructed.  
If the cooling fan becomes obstructed, a pro-  
tection circuit will automatically put the pro-  
jector into standby mode to prevent overheat  
damage. This does not indicate a malfunc-  
tion. (See pages 50 and 51.) Remove the pro-  
jector power cord from the wall outlet and wait  
at least 10 minutes. Place the projector where  
the intake and exhaust vents are not blocked,  
plug the power cord back in and turn on the  
projector. This will return the projector to the  
normal operating condition.  
After the projector is purchased, a faint smell  
from the vent may appear when the power is  
first turned on. This is normal and is not a  
malfunction. It will disappear after the projec-  
tor is used for a while.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution regarding usage of the projector Using the projector in other countries  
If you are not to use the projector for a long The power supply voltage and the shape of  
time or before moving the projector, make  
certain you unplug the power cord from the  
wall outlet, and disconnect any other cables  
connected to it.  
the plug may vary depending on the region  
or country you are using the projector in.  
When using the projector overseas, make  
sure you use an appropriate power cord for  
the country you are in.  
If the power cord is unplugged while the cool-  
ing fan is running, some parts of the projec-  
tor may still be hot. Use caution when han-  
dling the projector.  
Temperature monitor function  
Do not carry the projector by holding the lens.  
When storing the projector, ensure you at-  
tach the lens cap to the projector. (See page  
11.)  
Do not expose the projector to direct sunlight  
or place next to heat sources. Doing so may  
affect the cabinet color or cause deformation  
of the plastic cover.  
If the projector starts to overheat due to setup  
problems or blockage of the air vents, “ ” and  
” will illuminate in the lower left corner  
of the picture. If the temperature continues to  
rise, the lamp will turn off, the temperature warn-  
ing indicator on the projector will blink, and after  
a 60-second cooling-off period the projector will  
enter standby mode. Refer to “Maintenance In-  
dicators” on page 50 for details.  
Other connected equipment  
When connecting a computer or other audio-  
visual equipment to the projector, make the  
connections AFTER unplugging the power  
cord of the projector from the AC outlet and  
turning off the equipment to be connected.  
Please read the operation manuals of the pro-  
jector and the equipment to be connected for  
instructions on how to make the connections.  
Info  
The cooling fan regulates the internal tem-  
perature, and its performance is automatically  
controlled. The sound of the fan may change  
during projector operation due to changes in  
the fan speed.This does not indicate malfunc-  
tion.  
How to Access the PDF Operation Manuals  
PDF operation manuals in several languages are included in the CD-ROM. To uti-  
lize these manuals, you need to install Adobe® Reader® on your computer (Win-  
dows® or Macintosh®).  
Please download Adobe® Reader® from the Internet (http://www.adobe.com).  
Accessing the PDF Manuals for Windows® (For Macintosh®, skip step 2).  
1 Insert the CD-ROM in the CD-ROM drive.  
2 Double click the “My Computer” icon.  
3 Double click the “CD-ROM” drive.  
4 Double click the “MANUALS” folder.  
5 Double click the model (name of the folder)  
that you want to view.  
6 Double click the language (name of the  
folder) that you want to view.  
7 Double click the pdf file to access the pro-  
jector manuals.  
Note  
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first,  
then specify the desired file using the “File”, “Open” menu.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
Supplied accessories  
Two R-6 batteries  
(“AA” size, UM/SUM-3,  
HP-7 or similar)  
Remote control  
for XR-32X  
for XR-32S  
<RRMCGA662WJSA> <RRMCGA664WJSA>  
RGB cable  
(10' (3.0 m))  
Lens cap (attached)  
<CCAPHA027WJSA>  
<QCNWGA045WJPZ>  
Power cord*  
(1)  
(2)  
(3)  
(4)  
For U.S. and  
Canada, etc.  
(6' (1.8 m))  
For Europe,  
except U.K.  
(6' (1.8 m))  
For U.K. and  
Singapore  
For Australia, New  
Zealand and Oceania  
(6' (1.8 m))  
(6' (1.8 m))  
<QACCDA007WJPZ> <QACCVA011WJPZ> <QACCBA036WJPZ> <QACCLA018WJPZ>  
* Use the power cord that corresponds to the wall outlet in your country.  
• Operation manual (this manual <TINS-D520WJZZ> and CD-ROM <UDSKAA098WJZZ>)  
Note  
• Codes in “< >” are Replacement parts codes.  
Optional accessories  
Lamp unit  
AN-F212LP  
Ceiling-mount adaptor  
AN-60KT  
AN-XRCM30 (for U.S.A. only)  
Ceiling-mount unit  
AN-TK201 <for AN-60KT>  
AN-TK202 <for AN-60KT>  
AN-EP101B <for AN-XRCM30>  
(for U.S.A. only)  
Remote receiver  
AN-MR2  
AN-C3CP2  
AN-A1RS  
3 RCA to mini D-sub 15 pin cable (10n (3.0 m))  
DIN-D-sub RS-232C adapter (5 57  
(15 cm))  
/64"  
Note  
• Some of the optional accessories may not be available depending on the region. Please check with  
your nearest Sharp Authorized Projector Dealer or Service Center.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions  
Numbers in Z refer to the main pages in this operation manual where the topic  
is explained.  
Projector  
Top View  
Power  
indicator  
Lamp indicator  
25, 50  
25, 50  
Temperature warning  
indicator  
50  
32  
STANDBY/ON  
button  
ECO+QUIET button  
For lowering the noise  
of the cooling fan and  
extending the lamp life.  
25  
For turning the  
power on and  
putting the  
projector into  
standby mode.  
VOL (Volume) buttons  
(–O/Q+)  
For adjusting the  
speaker sound level.  
29  
29  
ENTER button  
For setting  
items selected  
or adjusted on  
the menu.  
38  
28  
INPUT buttons (P/R)  
For switching input mode.  
MENU/HELP button  
For displaying  
37, 46  
adjustment and  
setting screens, and  
help screen.  
KEYSTONE  
button  
For entering the  
Keystone  
Adjustment buttons  
(P/R/O/Q)  
Correction mode.  
37  
For selecting menu items.  
Front View  
Zoom ring  
For enlarging/  
reducing the picture.  
26  
Intake vent  
Remote control  
sensor  
49  
15  
Speaker  
45  
Exhaust vent  
49  
Focus ring  
For adjusting  
the focus.  
26  
HEIGHT  
ADJUST lever  
27  
Push both sides of the lens cap  
to attach or remove.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions (Continued)  
Numbers in Z refer to the main pages in this operation manual where the topic  
is explained.  
Rear View  
Terminals  
*AUDIO 1 input terminal  
S-VIDEO input terminal  
Terminal for connecting  
video equipment with an  
S-video terminal.  
22  
23  
COMPUTER/  
COMPONENT input  
terminal  
21  
22  
RS-232C terminal  
Terminal for  
24  
Terminal for computer RGB  
and component signals.  
controlling the  
projector using a  
computer.  
*DVI-D input  
terminal  
Terminal for  
21  
22  
USB terminal  
34  
DVI digital RGB  
and digital  
component  
signals.  
Terminal connecting  
with the USB  
terminal on the  
computer for using  
the supplied remote  
control as the  
computer mouse.  
*AUDIO OUT  
terminal  
23  
AUDIO 2 input  
terminal  
23  
Audio output terminal of  
equipment connected to the  
audio input terminal.  
(AUDIO input  
terminal for  
XR-32S)  
MONITOR OUT  
terminal  
23  
22  
VIDEO input  
terminal  
(Output terminal for computer RGB,  
component signals. Shared for COM-  
PUTER/COMPONENT)  
Terminal for  
connecting video  
equipment.  
Terminal for connecting a monitor.  
* XR-32X only  
AC socket  
Connect the supplied  
power cord.  
24  
Rear  
adjustment  
foot  
27  
Kensington Security  
Standard connector  
Using the Kensington Lock  
• This projector has a Kensington Security Standard connector for use with a Kensington  
MicroSaver Security System. Refer to the information that came with the system for  
instructions on how to use it to secure the projector.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STANDBY button  
ON button  
For turning the power  
on.  
25  
25  
For putting the projector  
into the standby mode.  
FREEZE button  
For freezing images.  
33  
29  
29  
COMPUTER, *DVI,  
S-VIDEO, VIDEO buttons  
For switching to the  
AV MUTE button  
For temporarily  
displaying a black  
screen and turning  
off the sound.  
respective input modes.  
BREAK TIMER button  
For displaying the  
break time.  
32  
VOL +/– (Volume)  
buttons  
For adjusting the  
29  
MAGNIFY buttons  
For enlarging/reducing  
part of the image.  
33  
speaker sound level.  
PAGE UP/PAGE  
DOWN buttons  
34  
SPOT button  
For displaying the  
spotlight.  
32  
38  
Same as the [Page Down] and  
[Page Up] keys on a computer  
keyboard, when with the USB  
connection (using a USB cable  
or the optional remote  
ENTER button  
For setting items  
selected or adjusted  
on the menu.  
receiver).  
POINTER button  
For displaying the  
pointer.  
32  
R-CLICK/RETURN  
button  
34  
38  
• For the Right click  
when with the USB  
connection (using a  
USB cable or the  
optional remote  
receiver).  
• For returning to the  
previous menu screen  
during menu  
MOUSE/Adjustment  
buttons (P/R/O/Q)  
• For moving the  
computer cursor when with the USB  
connection (using a USB cable or the  
optional remote receiver).  
• For selecting and adjusting menu  
items.  
34  
38  
operations.  
L-CLICK/EFFECT  
button  
• For the Left click  
34  
32  
when with the USB connection  
(using a USB cable or the optional  
remote receiver).  
• For changing the pointer or spot  
area.  
MENU/HELP button  
For displaying  
adjustment and  
setting screens, and  
help screen.  
38  
48  
KEYSTONE button  
For entering the  
Keystone Correction mode.  
28  
RESIZE button  
30  
33  
For switching the  
picture size (NOR-  
MAL, BORDER, etc.).  
AUTO SYNC button  
For automatically  
adjusting images when  
connected to a computer.  
33  
PICTURE MODE  
button  
For selecting the  
ECO+QUIET button  
32  
For lowering the noise  
of the cooling fan and  
extending the lamp life.  
appropriate picture.  
* XR-32X only  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions (Continued)  
Inserting the Batteries  
Pull down the tab on the cover and remove the cover  
towards the direction of the arrow.  
1
Insert the batteries.  
2
• Insert the batteries making sure the polarities correctly match  
the m and n marks inside the battery compartment.  
Insert the lower tab of the cover into the opening,  
and lower the cover until it clicks in place.  
3
Incorrect use of the batteries may cause them to leak or explode. Please  
follow the precautions below.  
Caution  
Danger of explosion if battery is incorrectly replaced.  
Replace only with alkaline or manganese batteries.  
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery  
compartment.  
Batteries of different types have different properties, therefore do not mix batteries of different types.  
Do not mix new and old batteries.  
This may shorten the life of new batteries or may cause old batteries to leak.  
Remove the batteries from the remote control once they have run out, as leaving them in can cause them  
to leak.  
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove  
them using a cloth.  
The batteries included with this projector may run down in a short period, depending on how they are kept.  
Be sure to replace them as soon as possible with new batteries.  
Remove the batteries from the remote control if you will not be using the remote control for a long time.  
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote control sensor  
Usable Range  
The remote control can be used to control the  
projector within the ranges shown in the illustra-  
tion.  
Note  
• The signal from the remote control can be re-  
flected off a screen for easy operation. How-  
ever, the effective distance of the signal may  
differ depending on the screen material.  
30°  
30°  
When using the remote control  
Ensure that you do not drop it or expose it to  
moisture or high temperature.  
23n (7 m)  
The remote control may malfunction under a  
fluorescent lamp. In this case, move the pro-  
jector away from the fluorescent lamp.  
Remote control  
signal transmitters  
Remote control  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Start  
This section shows the basic operation (projector connecting with the computer). For details, see  
the page described below for each step.  
Setup and Projection  
In this section, connection of the projector and the computer is explained using one example.  
3
8
6
STANDBY/ON  
button  
STANDBY button  
ON button  
8
3
INPUT buttons  
ENTER button  
4
5
COMPUTER button  
6
Adjustment buttons  
(P/R/O/Q)  
KEYSTONE  
button  
5
4
4
Zoom ring  
ENTER button  
4
5
5
Focus ring  
Adjustment buttons  
(P/R/O/Q)  
KEYSTONE button  
HEIGHT  
ADJUST lever  
4
_P. 18  
1. Place the projector facing a wall or a screen  
2. Connect the projector to the computer and plug the power cord  
into the AC socket of the projector  
When connecting equipment other than a computer, see  
pages 22 and 23.  
_PP. 21, 24  
3. Remove the lens cap and turn the projector on  
On the projector On the remote control  
_P. 25  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Adjust the projected image with the Setup Guide  
1 After the projector turns on, the Setup Guide appears.  
(When “Setup Guide” is set to “On”. See page 44.)  
2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).  
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup  
Guide.  
_PP. 26, 27  
5. Correct trapezoidal distortion  
Correcting trapezoidal distortion using Keystone Correction.  
On the projector  
Shrinks  
Shrinks  
lower side.  
upper side.  
On the remote control  
_P. 28  
6. Select the INPUT mode  
Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.  
On the On the remote  
projector  
control  
On-screen display (RGB)  
COMPUTER  
INPUT list  
INPUT  
RGB  
COMPUTER  
1024 × 768  
*
*
D
D
DVI-D Computer  
DVI-D Video  
XR-32X only  
• When you press INPUT on the projector, the INPUT list appears.  
Press '/" to switch the INPUT mode.  
_P. 29  
7.Turn the computer on  
8.Turn the power off  
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the  
button again while the confirmation message is displayed to put the projector into standby mode.  
On-screen display  
On the On the remote  
projector  
control  
_P. 25  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up the Projector  
Setting up the Projector  
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet  
flat and level. Doing so will eliminate the need for Keystone correction and provide the best image  
quality. (See page 28.)  
Standard Setup (Front Projection)  
Place the projector at the required distance from the screen according  
to the desired picture size. (See page 20.)  
Example of standard setup  
Side View  
Screen  
H
Lens center  
L
Note  
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.  
Ceiling-mount Setup  
It is recommended that you use the optional  
Sharp ceiling-mount adaptor and unit for this  
installation. Before mounting the projector,  
contact your nearest Sharp Authorized Pro-  
jector Dealer or Service Center to obtain the  
recommended ceiling-mount adaptor and unit  
(sold separately).  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projection (PRJ) Mode  
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode  
most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.  
See page 44.)  
Table mounted, front projection  
Ceiling mounted, front projection  
[Menu item “Front”]  
[Menu item “Ceiling + Front”]  
Table mounted, rear projection  
(with a translucent screen)  
[Menu item “Rear”]  
Ceiling mounted, rear projection  
(with a translucent screen)  
[Menu item “Ceiling + Rear”]  
Indication of the Projection Image Size and Projection Distance  
Example: NORMAL Mode (4:3)  
Picture Size  
300"  
240"  
×
180"  
200"  
160"  
×
120"  
100"  
80"  
60"  
80"  
×
60"  
48"  
64"  
×
36"  
48"  
×
Projection  
Distance  
"
"–8'6  
"
7'4  
(2.2 m – 2.6 m)  
"–11'4  
"
3.5 m)  
"–14'2  
"
9'10  
4.3 m)  
(3.0 m  
"–28'4  
12'3  
(3.7 m  
8.6 m)  
"
24'7  
(7.5 m  
36'10  
(11.2 m)  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up the Projector (Continued)  
Screen Size and Projection Distance  
NORMAL Mode (4:3)  
Picture (Screen) size  
Projection distance [L]  
Distance from the lens center  
to the bottom of the image [H]  
χ
Diag. [ ]  
Width  
Height  
Minimum [L1]  
Maximum [L2]  
300Љ (762 cm) 610 cm (240Љ) 457 cm (180Љ) 11.2 m (36Ј 10Љ)  
19 cm (7 9/16Љ)  
16 cm (6 19/64Љ)  
13 cm (5 3/64Љ)  
10 cm (3 25/32Љ)  
8 cm (3 1/32Љ)  
6 cm (2 33/64Љ)  
5 cm (2 1/64Љ)  
4 cm (1 49/64Љ)  
4 cm (1 33/64Љ)  
3 cm (1 1/64Љ)  
250Љ (635 cm) 508 cm (200Љ) 381 cm (150Љ) 9.4 m (30Ј 9Љ) 10.8 m (35Ј 5Љ)  
200Љ (508 cm) 406 cm (160Љ) 305 cm (120Љ) 7.5 m (24Ј 7Љ)  
8.6 m (28Ј 4Љ)  
6.5 m (21Ј 3Љ)  
5.2 m (17Ј 0Љ)  
4.3 m (14Ј 2Љ)  
3.5 m (11Ј 4Љ)  
3.0 m (9Ј 11Љ)  
2.6 m (8Ј 6Љ)  
1.7 m (5Ј 8Љ)  
150Љ (381 cm) 305 cm (120Љ) 229 cm (90Љ)  
5.6 m (18Ј 5Љ)  
4.5 m (14Ј 9Љ)  
3.7 m (12Ј 3Љ)  
3.0 m (9Ј 10Љ)  
2.6 m (8Ј 7Љ)  
2.2 m (7Ј 4Љ)  
1.5 m (4Ј 11Љ)  
120Љ (305 cm) 244 cm (96Љ)  
100Љ (254 cm) 203 cm (80Љ)  
80Љ (203 cm) 163 cm (64Љ)  
70Љ (178 cm) 142 cm (56Љ)  
60Љ (152 cm) 122 cm (48Љ)  
40Љ (102 cm) 81 cm (32Љ)  
183 cm (72Љ)  
152 cm (60Љ)  
122 cm (48Љ)  
107 cm (42Љ)  
91 cm (36Љ)  
61 cm (24Љ)  
χ
: Picture size (diag.) (in/cm)  
L: Projection distance (m/ft)  
The formula for picture size and projection distance  
[m/cm]  
L1 (m) = 0.03745  
L2 (m) = 0.04323  
[Feet/inches]  
L1 (ft) = 0.03745 / 0.3048  
L2 (ft) = 0.04323 / 0.3048  
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)  
L2: Maximum projection distance (m/ft)  
H: Distance from the lens center to the bottom of the image (cm/in)  
χ
χ
H (cm) = 0.064  
H (in) = 0.064 / 2.54  
STRETCH Mode (16:9)  
Picture (Screen) size  
Width  
Projection distance [L]  
Distance from the lens center to Adjustable range of  
χ
the bottom of the image [H]  
69 cm (27 19/64Љ)  
55 cm (21 53/64Љ)  
image position [S]  
ע
52 cm (
ע
20 27/64Љ)  
ע
42 cm (
ע
16 11/32Љ)  
Diag. [ ]  
Height  
Minimum [L1]  
Maximum [L2]  
250Љ (635 cm) 553 cm (218Љ) 311 cm (123Љ) 10.2 m (33Ј 6Љ) 11.8 m (38Ј 8Љ)  
200Љ (508 cm) 443 cm (174Љ) 249 cm (98Љ)  
150Љ (381 cm) 332 cm (131Љ) 187 cm (74Љ)  
120Љ (305 cm) 266 cm (105Љ) 149 cm (59Љ)  
8.2 m (26Ј 9Љ) 9.4 m (30Ј 11Љ)  
6.1 m (20Ј 1Љ) 7.1 m (23Ј 2Љ)  
4.9 m (16Ј 1Љ) 5.7 m (18Ј 7Љ)  
4.1 m (13Ј 5Љ) 4.7 m (15Ј 5Љ)  
3.3 m (10Ј 9Љ) 3.8 m (12Ј 4Љ)  
42 cm (16 3  
/8Љ)  
ע
31 cm (
ע
12 1  
/4Љ)  
33 cm (13 3/32Љ)  
28 cm (10 59/64Љ)  
22 cm (8 47/64Љ)  
17 cm (6 35/64Љ)  
11 cm (4 23/64Љ)  
ע
25 cm (
ע
9 13/16Љ)  
ע
21 cm (
ע
8 11/64Љ)  
ע
17 cm (
ע
6 17/32Љ)  
ע
12 cm (
ע
4 29/32Љ)  
ע
 8 cm (
ע
3 17/64Љ)  
100Љ (254 cm) 221 cm (87Љ)  
80Љ (203 cm) 177 cm (70Љ)  
60Љ (152 cm) 133 cm (52Љ)  
40Љ (102 cm) 89 cm (35Љ)  
125 cm (49Љ)  
100 cm (39Љ)  
75 cm (29Љ)  
50 cm (20Љ)  
2.4 m (8Ј 0Љ)  
2.8 m (9Ј 3Љ)  
1.6 m (5Ј 4Љ)  
1.9 m (6Ј 2Љ)  
χ
: Picture size (diag.) (in/cm)  
L: Projection distance (m/ft)  
The formula for picture size and projection distance  
[m/cm]  
L1 (m) = 0.0408  
L2 (m) = 0.0471  
[Feet/inches]  
L1 (ft) = 0.0408 / 0.3048  
L2 (ft) = 0.0471 / 0.3048  
H (in) = 0.27727 / 2.54  
χ
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)  
L2: Maximum projection distance (m/ft)  
H: Distance from the lens center to the bottom of the image (cm/in)  
χ
H (cm) = 0.27727  
χ
χ
S: Adjustable range of image position (cm/in) See page 43.  
S (cm) = 0.20754  
S (in) = 0.20754 / 2.54  
Note  
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the  
bottom of the image [H]”.  
• Allow a margin of error in the values in the diagrams above.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Projector to Other Equipment  
Before connecting, ensure that the power cord of the projector is unplugged from the AC  
outlet and turn off the equipment to be connected. After making all connections, turn on the  
projector and then the other pieces of equipment.When connecting a computer, ensure that  
it is the last equipment to be turned on after all the connections are made.  
IMPORTANT:  
Ensure that the appropriate input mode has been selected on the projector before  
you turn on the connected equipment.  
For more details of connection and cables, refer to the operation manual of the connecting equipment.  
You may need other cables or connectors not listed below.  
Terminals on the Projector  
Example:Terminals of XR-32X  
Terminal on  
connected equipment  
Terminal on the  
projector  
Equipment  
Computer  
Cable  
RGB cable (supplied)  
COMPUTER/  
COMPONENT  
RGB  
output  
terminal  
DVI Digital cable (commercially available)  
DVI-D  
DVI digital  
output  
terminal  
is only for XR-32X.  
Note  
• See page 62 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-  
tor. Use with computer signals other than those listed may cause some of the functions to not work.  
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-  
est Macintosh Dealer.  
Depending on the computer you are using, an image may not be projected unless the  
computer’s external output port is switched on (e.g. Press “Fn” and “F5keys simultaneously  
when using a SHARP notebook computer). Refer to the specific instructions in your computer's  
operation manual to enable your computer’s external output port.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Projector to Other Equipment (Continued)  
Terminal on  
Terminal on the  
projector  
Equipment  
Cable  
connected equipment  
Video equipment  
HDMI  
output  
terminal  
HDMI to DVI cable  
(commercially available)  
DVI-D  
DVI Digital cable (commercially available)  
DVI digital  
output  
terminal  
Component 3 RCA to mini D-sub 15 pin cable  
COMPUTER/  
COMPONENT  
video  
output  
terminal  
(optional, AN-C3CP2)  
S-video  
output  
S-video cable (commercially available)  
S-VIDEO  
VIDEO  
terminal  
Video  
output  
terminal  
Video cable (commercially available)  
Camera/Video game  
COMPUTER/  
COMPONENT  
Cables for a camera or a video game/3 RCA  
to mini D-sub 15 pin cable (optional,  
AN-C3CP2)  
Component  
video  
output  
terminal  
RCA adaptor plug  
(commercially available)  
Cables for a camera or a video game  
S-VIDEO  
VIDEO  
S-video  
output  
terminal  
Cables for a camera or a video game  
Video  
output  
terminal  
is only for XR-32X.  
Note  
• Only for XR-32X:  
- While the projector is connected to video equipment that has an HDMI output terminal, only the  
video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)  
- Depending on specifications of video equipment or HDMI to DVI digital cable, the signal trans-  
mission may not work property. (The HDMI specification does not support all connections to video  
equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)  
- For details on compatibility for connection, see support information on DVI connection provided  
by the video equipment manufacturer.  
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a  
commercially available cable that fits in the projector terminal you want to connect.  
• The projector does not support RGBC signals via the Euro-scart.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Terminal on  
connected equipment  
Terminal on the  
projector  
Equipment  
Cable  
Audio equipment  
ø3.5 mm stereo or mono audio cable  
(commercially available or available  
as Sharp service part QCNWGA038WJPZ)  
AUDIO 1  
ø3.5 mm  
audio output  
terminal  
RCA audio cable (commercially available)  
Cables for a camera or a video game  
AUDIO 2 (XR-32X)  
AUDIO (XR-32S)  
RCA audio  
output  
terminal  
Audio  
output  
terminal  
Monitor  
RGB cable (supplied or commercially  
available)  
MONITOR OUT  
RGB  
input  
terminal  
Amplifier  
ø3.5 mm stereo or mono audio cable  
(commercially available or available  
as Sharp service part QCNWGA038WJPZ)  
ø3.5 mm  
audio input  
terminal  
AUDIO OUT  
ø3.5 mm stereo minijack to RCA audio cable  
(commercially available)  
RCA audio  
input  
terminal  
is only for XR-32X.  
Note  
• Only for XR-32X:  
- When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5  
mm stereo audio cable.  
- You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 46.)  
• RGB signals and Component signals can be output to the monitor.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controlling the Projector by a Computer  
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-  
232C adaptor (optional, AN-A1RS) and an RS-232C serial control cable (cross type, commercially  
available), the computer can be used to control the projector and check the status of the projector.  
See page 57 for details.  
When connecting to a computer using an RS-232C serial control cable and a DIN-  
D-sub RS-232C adaptor  
To RS-232C terminal  
DIN-D-sub RS-232C  
adaptor (optional, AN-A1RS)  
Computer  
To RS-232C terminal  
RS-232C serial control cable (cross type, commercially available)  
Note  
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the  
operation manual of the computer for details.  
• See page 56 for connection of an RS-232C serial control cable.  
Info  
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This  
may damage your computer or projector.  
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.  
This may damage your computer.  
Connecting the Power Cord  
Plug the supplied power cord into the  
AC socket on the rear of the projector.  
Then plug into AC outlet.  
AC socket  
Power cord  
(supplied)  
To AC outlet  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning the Projector On/Off  
Info  
When “Auto Restart” is set to “On”:  
If the power cord is unplugged from the outlet  
or the breaker switch is turned off when the  
projector is on, then the projector automati-  
cally turns on when the power cord is plugged  
into the AC outlet or the breaker switch is  
turned on. (See page 45.)  
• English is the factory default language. If you  
want to change the on-screen display to an-  
other language, change the language accord-  
ing to the procedure on page 44.  
Turning the Projector on  
Note that the connections to external equip-  
ment and power outlet should be done be-  
fore performing the operations written be-  
low. (See pages 21 to 24.)  
Remove the lens cap and press  
STANDBY/ON on the projector or ON  
on the remote control.  
The power indicator illuminates green.  
After the lamp indicator illuminates, the projec-  
tor is ready to start operation.  
Lamp indicator  
Power indicator  
Note  
About the Lamp Indicator  
The lamp indicator illuminates to indicate the sta-  
tus of the lamp.  
STANDBY/ON button  
Green: The lamp is on.  
Blinking in green: The lamp is warming up.  
Red: The lamp is shut down abnormally  
or the lamp should be replaced.  
When switching on the projector, a slight flicker-  
ing of the image may be experienced within the  
first minute after the lamp has been illuminated.  
This is normal operation as the lamp’s control  
circuitry is stabilising the lamp output character-  
istics. It should not be regarded as faulty opera-  
tion.  
If the projector is put into standby mode and  
immediately turned on again, the lamp may take  
some time to start projection.  
STANDBY  
button  
When System Lock is set, the keycode input box  
appears. To cancel the keycode setting, input the  
keycode that you have already set. See page 46  
for details.  
ON button  
On-screen display (confirmation message)  
Turning the Power off (Putting  
the Projector into Standby Mode)  
Press STANDBY/ONon the projector or  
STANDBY on the remote control, then  
press that button again while the confir-  
mation message is displayed, to put the  
projector into standby mode.  
• The projector cannot be turned on while cool-  
ing.  
Info  
Direct Power Off function:  
You can unplug the power cord from the AC out-  
let even if the cooling fan is still running.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
Setup Guide screen  
About the Setup Guide  
After turning on the projector, the Setup  
Guide screen appears to assist you with  
projector setup.  
Guidance items  
1 FOCUS  
2 HEIGHT ADJUST  
3 ZOOM  
Press ENTER to exit the Setup Guide  
screen.  
Note  
• The Setup Guide screen automatically high-  
lights the items in the following order:  
1 FOCUS 2 HEIGHT ADJUST  
4 ENTER  
3 ZOOM  
STANDBY/ON  
button  
However, you can adjust the focus, height  
(angle), or zoom regardless of the highlighted  
item.  
• If you do not want to display the Setup Guide  
for the next time, set “Menu” - “SCR - ADJ” -  
“Setup Guide” to “Off”. (See page 44.)  
ENTER button  
Zoom ring  
Adjusting the Projected Image  
1 Adjusting the Focus  
You can adjust the focus with the focus  
ring on the projector.  
Rotate the focus ring to adjust the fo-  
cus while watching the projected image.  
2 Adjusting the Picture Size  
You can adjust the picture size using  
the zoom ring on the projector.  
Focus ring  
Rotate the zoom ring to enlarge or  
shrink the picture size.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 Adjusting the Height  
The height of the projector can be ad-  
justed using the adjustment feet at the  
front and rear of the projector.  
When the screen is above the projec-  
tor, the projection image can be made  
higher by adjusting the projector.  
Lift the projector to adjust its  
height while lifting the HEIGHT  
ADJUST lever.  
1
HEIGHT  
ADJUST lever  
Remove your hands from the  
HEIGHT ADJUST lever of the pro-  
jector after its height has been  
finely adjusted.  
• The angle of projection is adjustable up  
to 9 degrees from the surface on which  
the projector is placed.  
2
Make small  
adjustments.  
Use the rear adjustment foot to  
3
make the projector level.  
• The projector is adjustable 2 degrees  
from the standard position.  
Note  
• When adjusting the height of the projector,  
trapezoidal distortion occurs. Follow the pro-  
cedures in Keystone Correction to correct the  
distortion. (See pages 28 and 43.)  
Rear adjustment foot  
Info  
• Do not apply too much pressure on the pro-  
jector when the front adjustment foot comes  
out.  
• When lowering the projector, be careful not to  
get your fingers caught in the area between  
the adjustment foot and the projector.  
Hold the projector firmly while lifting or carrying.  
• Do not hold by the lens area.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
Correcting Trapezoidal  
Distortion  
Adjustment buttons  
(P/R/O/Q)  
When the image is projected either from  
the top or from the bottom towards the  
screen at an angle, the image becomes  
distorted trapezoidally.The function for  
correcting trapezoidal distortion is  
called Keystone Correction.  
Note  
RETURN button  
• The Keystone Correction can be adjusted up  
to an angle of approximately 40 degrees and  
the screen can also be set up to an angle of  
approximately 40 degrees (when the resize  
mode is set to “NORMAL” (see page 30)).  
KEYSTONE button  
On-screen display  
(Keystone Correction mode)  
KEYSTONE  
ADJUST  
0
Press KEYSTONE to enter the  
1
2
END  
Keystone Correction mode.  
• You can also display the on-screen dis-  
play of the Keystone Correction mode  
with KEYSTONE on the projector.  
Shrinks upper side.  
(Move the slide bar in the + direction.)  
Press P/Q or O/R to adjust the  
Keystone Correction.  
• You can also adjust the Keystone Cor-  
rection using the adjustment buttons on  
the projector.  
Shrinks lower side.  
(Move the slide bar in the - direction.)  
Note  
To return to the default setting, press RETURN  
while the on-screen display of the Keystone  
Correction mode is on the screen.  
Press KEYSTONE.  
3
• The on-screen display of the Keystone  
Correction mode will disappear.  
• You can also use KEYSTONE on the pro-  
jector.  
Info  
• While adjusting the image using Keystone  
Correction, straight lines and the edges of the  
image may appear jagged.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER,  
DVI (XR-32X only),  
S-VIDEO, VIDEO buttons  
Switching the Input Mode  
Select the appropriate input mode for  
the connected equipment.  
AV MUTE button  
Press COMPUTER, DVI (XR-32X only),  
S-VIDEO or VIDEO on the remote con-  
VOL +/– (Volume)  
buttons  
trol to select the input mode.  
• When you press INPUT on the projector or DVI  
on the remote control (XR-32X only), the INPUT  
list appears.  
Press P/R to switch the INPUT mode.  
Adjusting the Volume  
Press VOL +/– on the remote control or  
O/Q+ on the projector to adjust the vol-  
ume.  
Note  
• Pressing VOL–/O will lower the volume.  
• Pressing VOL+/Q+ will raise the volume.  
• When the projector is connected to external  
equipment, the volume level of the external equip-  
ment changes in accordance with the volume  
level of the projector. Set the projector’s volume  
to the lowest level when turning the projector on/  
off or when changing the input signal.  
On-screen display  
• When you do not want to output the sound from  
the projector’s speaker while the projector is con-  
nected to external equipment, set “Speaker” in  
“PRJ-ADJ” menu to “Off”. (See page 45.)  
Displaying the Black Screen  
and Turning off the Sound  
Temporarily  
Press AV MUTE on the remote control  
to temporarily display a black screen  
and turn off the sound.  
On-screen display  
Note  
• Pressing AV MUTE again will turn the pro-  
jected image back on.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
Resize Mode  
This function allows you to modify or customize the resize mode to enhance the input image. De-  
pending on the input signal, you can choose a desired image.  
Press RESIZE.  
• See page 43 for setting on menu screen.  
RESIZE  
button  
COMPUTER  
Main resolution  
SVGA (800 x 600)  
XGA (1024 x 768)  
SXGA (1152 x 864)  
1280 x 800  
NORMAL  
1024 x 768  
1024 x 640  
800 x 600  
800 x 500  
FULL  
DOT BY DOT  
BORDER  
768 x 576  
922 x 576  
600 x 450  
720 x 450  
STRETCH  
800 x 600  
XR-32X  
XR-32S  
1024 x 576  
1152 x 864  
1280 x 800  
1024 x 768  
SVGA (800 x 600)  
XGA (1024 x 768)  
SXGA (1152 x 864)  
1280 x 800  
1024 x 768  
1152 x 864  
1280 x 800  
800 x 450  
800 x 600  
For 4:3 screen  
FULL  
Input signal  
For 16:9 screen  
Computer  
Image type  
NORMAL  
DOT BY DOT  
BORDER  
STRETCH  
XR-32X  
XR-32S  
Resolution Resolution  
lower than lower than  
XGA  
SVGA  
2
2
XGA  
SVGA  
*
*
1
*1, *3  
*
4:3 aspect ratio  
Resolution  
higher  
than  
Resolution  
higher than  
XGA  
SVGA  
SXGA (1280 × 1024)  
5:4 aspect ratio  
16:9 aspect ratio  
1
1
*
*
1280 × 720  
2
2
*
*
1360 × 768  
1366 × 768  
1280 × 768  
1
1
*
*
1280 × 800  
16:10 aspect ratio  
: Cutout area on which images cannot be projected  
: Area where the signals are off screen  
The Image Shift function can be used for these images.  
Same as NORMAL mode.  
For XR-30S model, you cannot select BORDER when the resolution (1280 x 1024, etc.) that the horizontal ratio is smaller than 4:3 aspect ratio is  
selected.  
1
2
3
*
*
*
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO/DTV  
Input signal  
For 4:3 screen  
AREA ZOOM  
For 16:9 screen  
BORDER STRETCH  
Video/DTV  
Image type  
NORMAL  
V-STRETCH  
1
1
1
*
*
*
*
*
*
4:3 aspect ratio  
1
480I, 480P,  
576I, 576P,  
NTSC, PAL,  
SECAM  
Squeeze  
1
1
Letter box  
720P, 1035I,  
1080I  
1
*
16:9 aspect ratio  
2
*
2
*
16:9 aspect ratio  
540P  
1
*
(4:3 aspect ratio in 16:9)  
: Cutout area on which images cannot be projected  
: Area on which the image is not included in the original signals  
The Image Shift function can be used for these images.  
Same as NORMAL mode.  
1
2
*
*
About Copyrights  
• When using the RESIZE function to select an image size with a different aspect ratio to  
a TV program or video image, the image will look different from its original appearance.  
Keep this in mind while choosing an image size.  
• The use of the Resize or Keystone Correction function to compress or stretch the image  
for commercial purposes/public displays in a café, hotel, etc. may be an infringement of  
copyright protected by law for copyright holders. Please use caution.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating with the Remote Control  
BREAK TIMER button  
FREEZE button  
Displaying the Pointer  
MAGNIFY buttons  
Press POINTER and press P/R/  
1
O/Qon the remote control to move  
POINTER button  
SPOT button  
the pointer.  
• Press EFFECT to change the pointer icon  
(5 types).  
Press POINTER again.  
• The pointer will disappear.  
Adjustment buttons  
2
(P/R/O/Q)  
EFFECT button  
PICTURE MODE button  
ECO+QUIET button  
AUTO SYNC button  
Using the Spot Function  
Press SPOT and press P/R/O/Q  
1
on the remote control to move the  
Displaying and Setting the  
Break Timer  
spot area.  
• Press EFFECT to change the spot area  
size (3 types).  
Press BREAK TIMER.  
• The timer starts to count down from 5  
minutes.  
Press SPOT again.  
• The spot area will disappear.  
1
2
On-screen display  
Press P /R /O /Q to adjust the  
Switching the Eco+Quiet  
Mode  
2
length of the break time.  
Increases with P or Q  
5 minutes s 6 minutes s 60 minutes  
Shortens with O or R  
4 minutes s 3 minutes s1 minute  
• The break time can be set in units of one  
minute (up to 60 minutes).  
Press ECO+QUIET to switch the  
Eco+Quiet mode between on and off.  
• When the Eco+Quiet Mode is set to “ON”, the  
sound of the cooling fan will turn down, the  
power consumption will decrease, and the lamp  
life will extend.  
Canceling the break timer display function  
Press BREAK TIMER.  
Note  
• Refer to “Lamp Setting” on page 42 for de-  
tails of the Eco+Quiet mode.  
Note  
• Break Timer does not function while the pro-  
jector is operating the “Auto Sync”, “FREEZE”  
or “AV MUTE” functions.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Auto Sync  
(Auto Sync Adjustment)  
Displaying an Enlarged  
Portion of an Image  
Graphs, tables and other portions of  
projected images can be enlarged.This  
is helpful when providing more detailed  
explanations.  
Auto Sync function works when detect-  
ing input signal after the projector turns  
on.  
Press AUTO SYNC to manually adjust  
with Auto Sync function.  
Press  
MAGNIFY on the remote  
1
control.  
Note  
• Enlarges the image.  
• When the optimum image cannot be achieved  
with Auto Sync adjustment, use the help menu  
for manual adjustments. (See page 48.)  
• Pressing  
or  
MAGNIFY enlarges  
or reduces the projected image.  
Note  
Press  
2
.
.
1
3
4
Freezing a Moving Image  
Press  
• You can change the location of the en-  
larged image using P, R, O and Q.  
Press FREEZE.  
• The projected image is frozen.  
1
Press FREEZE again to return to  
Press RETURN on the remote con-  
trol to cancel the operation.  
• The magnification then returns to ×1.  
2
2
the moving image from the cur-  
rently connected device.  
Note  
• The selectable magnifications differ de-  
pending on the input signal.  
• In the following cases, the image will  
return to the normal size (×1).  
Selecting the Picture Mode  
- When switching the INPUT mode.  
- When RETURN has been pressed.  
- When the input signal is changed.  
- When the input signal resolution and  
refresh rate (vertical frequency)  
change.  
- When the Resize mode is changed.  
- When the Picture mode is changed.  
- When the Progressive mode is changed.  
You can select the appropriate picture  
mode for the projected image, such as  
movie or video game.  
Press PICTURE MODE.  
• When pressing PICTURE MODE, the picture  
mode changes in the following order:  
*
STANDARD PRESENTATION  
MOVIE GAME sRGB  
Note  
• See page 40 for details on the picture mode.  
* “sRGB” is displayed only when RGB signal is  
input.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating with the Remote Control (Continued)  
Using the Remote Control as the Wireless Computer Mouse  
When connecting the projector and the computer with a USB cable, you can use  
the remote control as the computer mouse.  
If the computer is placed too far away from the projector to be connected via the  
USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate  
the projector with the remote control. For details, see the operation manual of  
the receiver.  
Connecting with a USB cable  
Computer  
R
emote receiver  
To USB terminal  
(optional, AN-MR2)  
To USB terminal  
or  
USB cable  
(commercially available or available as  
Sharp service part QCNWGA014WJPZ)  
PAGE UP/  
PAGE DOWN buttons  
The mouse pointer can be oper-  
ated in the following way after it  
is connected.  
MOUSE/Adjustment  
buttons ('/"/\/|)  
When moving the cursor  
Press MOUSE/Adjustment buttons (P/R/O/Q).  
When left-clicking  
Press L-CLICK.  
When right-clicking  
R-CLICK button  
L-CLICK button  
Press R-CLICK.  
When your computer supports only a  
one-click mouse (such as Macintosh)  
Press L-CLICK or R-CLICK.  
L-CLICK and R-CLICK have common function.  
When using [Page Up] or [Page Down]  
Same as the [Page Up] and [Page Down] keys on a computer keyboard.  
Press PAGE UP or PAGE DOWN.  
Note  
• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function  
does not work with the following operation systems that do not support USB.  
• Versions earlier than Windows® 95  
• Versions earlier than Windows® NT4.0  
• Versions earlier than Mac OS® 8.5  
• You cannot use this function when displaying the menu screen.  
• Confirm that the computer recognizes the USB connection.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items  
The following shows the items that can be set in the projector.  
Main menu  
Sub menu  
“Picture” menu  
Standard  
Presentation  
Movie  
Picture  
Picture Mode  
Page 40  
Page 40  
PAGE 1  
Game  
sRGB*1  
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
Picture Mode  
Contrast  
Bright  
Color  
0
0
0
0
0
Contrast  
Bright  
Color  
Tint  
-30  
-30  
-30  
-30  
-30  
-30  
-30  
+30  
+30  
+30 *2  
Tint  
Sharp  
Red  
*2  
+30  
0
0
Sharp  
Red  
+30 *2  
+30  
Blue  
Blue  
+30  
Page 41  
SEL./ADJ.  
ENTER  
END  
Help  
PAGE 2  
CLR Temp  
-1  
0
1
2
Picture  
SCR - ADJ  
PRJ - ADJ  
Page 41  
Bright Boost  
Picture Mode  
Standard  
0
1
Page 41  
C.M.S. Setting [On/Off]  
Page 41  
C.M.S.  
CLR Temp  
Bright Boost  
C.M.S. Setting  
C.M.S.  
Progressive  
DNR  
On  
3D Progressive  
Off  
Page 41  
Progressive  
Lamp Setting  
Reset  
Bright  
2D Progressive  
3D Progressive  
Film Mode  
*2  
Page 42  
DNR  
Off  
Level 1  
Level 2  
SEL./ADJ.  
ENTER  
END  
Page 42  
Lamp Setting  
Bright  
Eco + Quiet  
Page 42  
Reset  
“C.M.S.”  
C. M. S.  
C. M. S. - Hue  
C. M. S. - Saturation  
C. M. S. - Value  
Reset  
C.M.S.-Hue  
R
Y
-30  
-30  
-30  
-30  
-30  
-30  
+30  
+30  
+30  
+30  
+30  
+30  
Page 41  
C.M.S.-Saturation  
G
R
0
0
0
0
0
0
C
Page 41  
C.M.S.-Value  
Y
G
B
C
M
Page 41  
Reset  
B
Reset  
M
Reset  
SEL./ADJ.  
Return  
ENTER  
END  
*1 Items when inputting RGB signal through  
COMPUTER or DVI (XR-32X only).  
*2 Items when inputting component signal through  
COMPUTER or DVI (XR-32X only), or when selecting  
S-VIDEO or VIDEO.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items (Continued)  
“Screen adjustment (SCR-ADJ)” menu  
Main menu  
SCR - ADJ  
Sub menu  
Picture  
Resize  
SCR - ADJ  
PRJ - ADJ  
Border  
Help  
Resize  
Normal  
Normal  
Full  
Area Zoom  
V-Stretch  
Border  
Image Shift  
Keystone  
0
0
Page 43  
Page 43  
Dot By Dot  
Area Zoom  
V-Stretch  
Border  
Image Shift  
Stretch  
-96 +96 *3  
-75 +75 *4  
OSD Display  
Closed Caption  
Background  
Setup Guide  
PRJ Mode  
On  
VIDEO/  
S-VIDEO  
Stretch  
Page 43  
Off  
COMPUTER/  
DTV  
Logo  
On  
Keystone  
-80 +80 *3  
-40 +40  
*4  
Front  
English  
Page 43  
OSD Display [On/Off]  
Language  
Page 43  
Closed Caption  
Page 44  
SEL./ADJ.  
ENTER  
END  
Off  
CC1  
CC2  
*3 Adjustment range for XR-32X.  
*4 Adjustment range for XR-32S.  
Logo  
Blue  
None  
Background  
Page 44  
Setup Guide [On/Off]  
Page 44  
PRJ Mode  
Front  
Ceiling + Front  
Rear  
Ceiling + Rear  
Page 44  
English  
Language  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Page 44  
Svenska  
Português  
polski  
Magyar  
Türkçe  
“Projector adjustment (PRJ-ADJ)” menu  
Main menu  
PRJ - ADJ  
Sub menu  
Picture  
SCR - ADJ  
PRJ - ADJ  
Help  
Auto Sync [On/Off]  
Auto Sync  
On  
On  
On  
Auto Power Off  
Auto Restart  
STANDBY Mode  
System Sound  
Speaker  
Page 45  
Page 45  
Auto Power Off [On/Off]  
Standard  
Page 45  
Auto Restart [On/Off]  
On  
On  
Page 45  
Audio Input  
RS-232C  
Audio 1  
9600bps  
Normal  
Disable  
STANDBY Mode  
Standard  
Eco  
Fan Mode  
Page 45  
System Sound [On/Off]  
System Lock  
Lamp Timer(Life)  
0
h
0
min 100%  
Page 45  
Speaker [On/Off]  
SEL./ADJ.  
ENTER  
END  
Page 45  
*5  
*5 This item is available for XR-32X only.  
Audio Input  
Audio 1  
Audio 2  
Page 46  
RS-232C  
9600bps  
115200bps  
Page 46  
Fan Mode  
Normal  
High  
Page 46  
System Lock  
[Enable/Disable]  
Page 46  
Lamp Timer(Life)  
Page 47  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
“Help” menu  
The items you can set with the “Help”  
menu  
Picture  
SCR - ADJ  
PRJ - ADJ  
Help  
“Help” menu n Page 48  
• Vertical stripes or flickering image appear  
Auto Sync  
There is no picture or audio  
Vertical stripes or flickering image appear  
Data image is not centered  
Color is faded or poor  
Clock  
Phase  
Picture is dark  
• Data image is not centered  
Auto Sync  
The image is distorted  
Reset all adjustments to default settings  
H-Pos  
V-Pos  
• Color is faded or poor  
COMPUTER/COMPONENT or DVI (XR-32X  
only) input  
SEL.  
ENTER  
END  
Signal type: Auto/RGB/Component  
S-VIDEO or VIDEO input  
Video System: Auto/PAL/SECAM/  
NTSC3.58/NTSC4.43/  
PAL-M/PAL-N/PAL-60  
DVI (Digital) input (XR-32X only)  
Dynamic range: Auto/Standard/Enhanced  
* The selectable items vary depending on the in-  
put signal and the selected input mode.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menu Screen  
ENTER button  
Adjustment buttons (P/R/O/Q)  
MENU/HELP button  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
RETURN button  
• Press RETURN to return  
to the previous screen  
when the menu is  
displayed.  
MENU/HELP button  
Menu Selections (Adjustments)  
Example: Adjusting “Bright”.  
• This operation can also be performed by using the buttons on the projector.  
Example: “Picture” screen menu for  
Press MENU/HELP.  
1
2
COMPUTER (RGB) input  
• The “Picture” menu screen for the se-  
lected input mode is displayed.  
Menu item  
Press Q or O and selectPicture”  
to adjust.  
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
Picture Mode  
Contrast  
Bright  
0
0
0
0
0
1
Red  
Blue  
CLR Temp  
Bright Boost  
On  
C.M.S. Setting  
C.M.S.  
DNR  
Off  
Lamp Setting  
Reset  
Bright  
SEL./ADJ.  
ENTER  
END  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Press P or R and select “Bright”  
to adjust.  
• The selected item is highlighted.  
3
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
Picture Mode  
Contrast  
Bright  
0
0
0
0
0
1
Red  
Blue  
CLR Temp  
Bright Boost  
On  
C.M.S. Setting  
C.M.S.  
DNR  
Off  
Lamp Setting  
Reset  
Bright  
SEL./ADJ.  
Single ADJ  
END  
Help  
Items to be adjusted  
Picture  
Resize  
SCR - ADJ  
PRJ - ADJ  
Border  
Image Shift  
Keystone  
0
0
To adjust the projected  
image while watching it  
Press ENTER.  
Press ENTER.  
• The selected item (e.g. “Bright”) is dis-  
played by itself at the bottom of the  
screen.  
• When pressing P or R, the following item  
(“Red” after “Bright”) will be displayed.  
The item displayed by itself  
Picture  
Bright  
0
SEL./ADJ.  
Rtn. Menu  
END  
Note  
• Press ENTER again to return to the pre-  
vious screen.  
Press O or Q to adjust the item  
selected.  
4
5
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
Picture Mode  
Contrast  
Bright  
• The adjustment is stored.  
0
1 5  
0
Red  
Blue  
0
0
CLR Temp  
Bright Boost  
C.M.S. Setting  
C.M.S.  
1
On  
DNR  
Lamp Setting  
Reset  
Off  
Bright  
Press MENU/HELP.  
• The menu screen will disappear.  
SEL./ADJ.  
Single ADJ  
END  
Note  
• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”,  
“FREEZE”, or “AV MUTE” functions.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu)  
Menu operation n Page 38  
Q PAGE1  
Q PAGE2  
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
Picture  
SCR - ADJ  
PRJ - ADJ  
Standard  
Help  
1
2
Picture Mode  
Contrast  
Bright  
Color  
Picture Mode  
0
0
0
0
0
0
1
CLR Temp  
3
2
4
5
6
7
Bright Boost  
Tint  
C.M.S. Setting  
C.M.S.  
Progressive  
DNR  
On  
Sharp  
Red  
0
0
3D Progressive  
Off  
Blue  
Lamp Setting  
Reset  
Bright  
SEL./ADJ.  
ENTER  
END  
SEL./ADJ.  
ENTER  
END  
1 Selecting the Picture Mode  
The default settings of each item when selecting Picture Mode  
Selectable  
items  
Description  
CLR Temp  
Bright Boost  
Lamp Setting  
Standard  
For standard image  
1
2
Bright  
Bright  
0
0
Presentation Brightens portions of image for  
more enhanced presentations.  
Movie  
Game  
*sRGB  
Gives natural tint to the  
projected image.  
0
1
Eco + Quiet  
Bright  
–1  
0
Gives sharpness to the  
projected image.  
For high fidelity reproduction of  
images from a computer.  
Bright  
• “sRGB” is displayed only when RGB signal is input.  
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are  
retained in memory.  
Note  
You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)  
• *sRGB is an international standard of color reproduction regulated by the IEC (International  
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are  
displayed in a natural tint based on an original image, when “sRGB” is selected.  
For additional information about the sRGB function, visit “http://www.srgb.com/”.  
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “Bright Boost”, when “sRGB” is selected.  
Info  
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a  
malfunction.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 38  
2 Adjusting the Image  
4 Adjusting the Colors  
This function adjusts each of the six main colors  
that comprise the color wheel, altering their  
“Hue”, “Saturation”, or “Value”.  
Adjustment  
items  
O button  
Q button  
Contrast  
For less  
contrast.  
For more  
contrast.  
Selectable items  
Description  
Bright  
Color*1  
Tint*1  
For less  
brightness.  
For less color  
intensity.  
For making skin For making skin  
tones purplish. tones greenish.  
For more  
brightness.  
For more color  
intensity.  
C.M.S.-Hue  
Sets the hue of the main colors.  
C.M.S.-Saturation Sets the saturation of the main  
colors  
C.M.S.-Value  
Sets the brightness of the main  
colors.  
Sharp*1  
For less  
For more  
Reset  
The adjustments of “Hue”,  
“Saturation” and “Value” of all  
colors are reset to the default  
setting.  
sharpness.  
sharpness.  
Red*2  
Blue*2  
For weaker red. For stronger red.  
For weaker blue. For stronger blue.  
Bright Boost™*2 For making the For making the  
Adjusting “Hue”, “Saturation”, or “Value”.  
effect weaker.  
effect stronger.  
1Select “On” for “C.M.S. Setting” in the “Picture”  
*1 Not displayed in the RGB input mode.  
*2 Not adjustable/selectable when selecting “sRGB”.  
2mSeelneuctanCd.Mth.Se.npinrethsse EPNicTtEuRre.” menu and then  
3Pprreessss EPNoTrERR.to select either “Hue”, “Saturation”, or  
“Value” and then press ENTER.  
Note  
4Select the color to be adjusted with P or R and  
• “Red”, “Blue”, “Bright Boost” and “CLR Temp”  
cannot be set when “sRGB” is selected.  
To reset all adjustment items, select “Reset”  
and press ENTER.  
adjust it with O or Q.  
Example of adjusting the “Hue”  
Main colors  
R (Red)  
O button  
Q button  
Closer to magenta Closer to yellow  
3 Adjusting the Color  
Y (Yellow)  
G (Green)  
C (Cyan)  
B (Blue)  
Closer to red  
Closer to green  
Closer to cyan  
Closer to blue  
Closer to magenta  
Closer to red  
Temperature  
Closer to yellow  
Closer to green  
Closer to cyan  
Selectable  
Description  
items  
M (Magenta) Closer to blue  
For lower color temperature for  
warmer, reddish incandescent-like  
–1  
0
When “Saturation” is selected, the selected  
color becomes  
O: lighter. Q: thicker.  
When “Value” is selected, the selected color  
becomes  
images.  
P
R
For higher color temperature for  
1
cooler, bluish, fluorescent-like images.  
O: darker. Q: brighter.  
To reset the adjustment values of each color  
to the default settings, select “Reset” and press  
ENTER.  
Note  
• Values on “CLR Temp” are only for general  
standard purposes.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu)  
(Continued)  
Menu operation n Page 38  
5 Progressive  
6
Reducing Image Noise (DNR)  
Video digital noise reduction (DNR) provides high  
quality images with minimal dot crawl and cross  
color noise.  
Selectable  
items  
Description  
2D Useful to display fast-moving images  
Progressive such as sports.  
Selectable  
Description  
items  
3D  
Useful to display relatively slow-  
Progressive moving images such as drama and  
documentary more clearly.  
Off  
The DNR function is not activated.  
Level 1  
Level 2  
Sets the DNR level for viewing a  
clearer picture.  
Film Mode Reproduces the image of film source*  
clearly. Displays the optimized image of  
film transformed with three-two pull down  
(NTSC and PAL60Hz) or two-two pull  
down (PAL50Hz and SECAM) enhance-  
ment to progressive mode images.  
Note  
Set “DNR” to “Off” in the following cases:  
• When the image is blurry.  
• When the contours and colors of moving im-  
ages drag.  
• When TV broadcasts with weak signals are  
projected.  
* The film source is a digital video recording with the  
original encoded as is at 24 frames/second. The  
projector can convert this film source to progres-  
sive video at 60 frames/second with NTSC and  
PAL60Hz or at 50 frames/second with PAL50Hz  
and SECAM to play back a high-definition image.  
Note  
7 Lamp Setting  
• In NTSC or PAL60Hz, even if the 3D Progres-  
sive mode has been set, the three-two pull  
down enhancement will be enabled automati-  
cally when the film source has been entered.  
• When the image is blurred or noisy, switch to  
the optimal mode.  
Selectable  
Brightness and Power consumption  
items  
Eco + Quiet  
Bright  
Approx. 80%  
100%  
Info  
Note  
• This function is available for 480I and 576I  
signals using COMPUTER/COMPONENT or  
DVI (XR-32X only) input.  
• This function is available for all signals with  
S-VIDEO and VIDEO input.  
• In the Eco + Quiet mode, the fan sound and  
power consumption are lower than those in  
the Bright mode. (Projection brightness de-  
creases as shown in the chart.)  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projected Image  
(“SCR - ADJ” Menu)  
Menu operation n Page 38  
Picture  
Resize  
SCR - ADJ  
PRJ - ADJ  
Border  
Help  
1
2
3
Image Shift  
Keystone  
0
0
4
5
6
7
8
9
OSD Display  
Closed Caption  
Background  
Setup Guide  
PRJ Mode  
On  
Off  
Logo  
On  
Front  
English  
Language  
SEL./ADJ.  
ENTER  
END  
3 Keystone Correction  
1 Setting the Resize Mode  
When the image is projected either from the top  
or from the bottom towards the screen at an angle,  
the image becomes distorted trapezoidally. The  
function for correcting trapezoidal distortion is  
called Keystone Correction.  
Note  
• For details of the Resize mode, see pages  
30 and 31.  
You can also press RESIZE on the remote con-  
trol to set the resize mode. (See page 30.)  
Select “Keystone” on the “SCR-ADJ”  
menu and adjust with the slide bar.  
See page 28 for details of Keystone Correction.  
2 Adjusting the Image  
Q button  
O button  
Position  
You can move the projected image vertically.  
Note  
• The Keystone Correction can be adjusted up  
to an angle of approximately 40 degrees  
(when “Resize” is set to “Normal”).  
• You can also press KEYSTONE on the remote  
control or on the projector to adjust Keystone  
Correction.  
O button  
Q button  
4 Setting the On-screen  
Display  
Selectable  
Description  
items  
Note  
• This function only works in some RESIZE  
modes. (See pages 30 and 31.)  
On  
Off  
All on-screen displays are displayed.  
INPUT/VOLUME/AV MUTE/FREEZE/  
AUTO SYNC/RESIZE/PICTURE MODE/  
ECO+QUIET/MAGNIFY/ “An invalid  
button has been pressed.” are not  
displayed.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projected Image  
(“SCR - ADJ” Menu) (Continued)  
Menu operation n Page 38  
5 Closed Caption  
“Closed Caption” is a system which allows  
conversations, narration, and sound effects in  
TV programs and home videos to be viewed  
as captions on the screen.  
Not all programs and videos will offer closed  
captioning. Please look for the  
ensure that captions will be shown.  
Two channels are available: CH1 and CH2.  
“Closed Caption” shows subscripts of dialogs  
and commentaries of TV dramas and news  
programs while allowing a clear view of the  
picture.  
8 Reversing/Inverting  
Projected Images  
Selectable items  
Front  
Description  
Normal image (Projected from  
the front of the screen)  
symbol to  
Ceiling + Front  
Rear  
Inverted image (Projected  
from the front of the screen  
with an inverted projector)  
Reversed image (Projected  
from the rear of the screen or  
with a mirror)  
Ceiling + Rear  
Reversed and inverted image  
(Projected with a mirror)  
Selectable items  
Description  
Off  
See page 19 for details of Projection (PRJ) Mode.  
CC1  
CC2  
Closed Caption mode for CH1 data  
Closed Caption mode for CH2 data  
9
Selecting the On-screen  
Display Language  
Note  
• This function enables the display of captions  
(text content) which are standardized by the  
Federal Communications Commission, an  
independent US government agency.  
• Closed Caption may malfunction (white blocks,  
strange characters, etc.) if signal conditions are  
poor or if there are problems at the broadcast  
source. This does not necessarily indicate a  
problem with the projector.  
The projector can switch the on-screen display  
language among 17 languages.  
English  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
If any button is pressed to call up the on-screen  
display while viewing a Closed Caption broadcast,  
the closed captions will disappear momentarily.  
Svenska  
Português  
polski  
Magyar  
6
Selecting the Background  
Image  
Türkçe  
Selectable items  
Logo  
Blue  
Description  
Sharp logo screen  
Blue screen  
None  
7
Selecting the Setup Guide  
Selectable items  
Description  
On  
Displaying the Setup Guide  
when turning the projector on.  
Off  
Not displaying the Setup Guide.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projector Function (“PRJ - ADJ” Menu)  
Menu operation n Page 38  
Picture  
SCR - ADJ  
PRJ - ADJ  
Help  
3 Auto Restart Function  
Selectable  
Description  
items  
1
2
3
4
5
6
7
8
9
0
Auto Sync  
On  
On  
On  
Auto Power Off  
Auto Restart  
STANDBY Mode  
System Sound  
Speaker  
Standard  
On  
On  
If the power cord is unplugged from the  
outlet or the breaker switch is turned off  
when the projector is on, then the  
On  
Audio Input  
RS-232C  
Audio 1  
9600bps  
Normal  
Disable  
projector automatically turns on when  
the power cord is plugged into the AC  
outlet or the breaker switch is turned on.  
Fan Mode  
System Lock  
Lamp Timer(Life)  
0
h
0
min 100%  
Off  
The projector does not turn on  
automatically when the power cord is  
plugged into the AC outlet or the  
breaker switch is turned on.  
SEL./ADJ.  
ENTER  
END  
1
Auto Sync (Auto Sync  
Adjustment)  
4 STANDBY Mode  
When set to “Eco”, power consumption is re-  
duced in standby mode.  
Selectable  
items  
Description  
On  
Auto Sync adjustment will occur when  
the projector is turned on or when the  
input signals are switched, when  
connected to a computer.  
Selectable  
Description  
items  
Eco  
The monitor output and RS-232C  
functions are switched off in standby  
mode.  
Off  
Auto Sync adjustment is not automati-  
cally performed.  
Standard  
The monitor output and RS-232C  
functions are activated even if the  
projector is in standby mode.  
Note  
• Auto Sync adjustment is also performed by  
pressing AUTO SYNC on the remote control.  
• The Auto Sync adjustment may take some time  
to complete, depending on the image of the  
computer connected to the projector.  
5
Setting the Confirmation  
Sound (System Sound)  
• When the optimum image cannot be achieved  
with Auto Sync adjustment, use manual ad-  
justments. (See page 48.)  
Selectable  
items  
Description  
On  
A confirmation sound is made when  
the projector turns on/off.  
2
Auto Power Off Function  
Off  
No confirmation sound is made.  
Selectable  
items  
Description  
6 Speaker Setting  
Selectable  
Description  
items  
On  
When no input signal is detected for  
more than 15 minutes, the projector will  
automatically enter standby mode.  
Off  
The Auto Power Off function will be  
disabled.  
On  
The audio signal is output from the  
internal speaker.  
Off  
The audio signal is not output from the  
internal speaker.  
Note  
• When the Auto Power Off function is set to  
“On”, 5 minutes before the projector enters  
standby mode, the message “Enter STANDBY  
mode in X min.” will appear on the screen to  
indicate the remaining minutes.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projector Function (“PRJ - ADJ” Menu)  
(Continued)  
Menu operation n Page 38  
a Setting/Changing the keycode  
7
Audio Input (XR-32X only)  
Select “System Lock”, then press  
ENTER or Q.  
This function allows you to select an appropri-  
ate combination of audio input terminals for each  
input mode.  
1
2
Selectable  
Description  
items  
Select “Next”, then press ENTER.  
The screen for entering the keycode  
appears.  
Audio 1  
The AUDIO 1 input terminal is used as  
an audio input terminal.  
Audio 2  
The AUDIO 2 input terminal is used as  
an audio input terminal.  
Press the 4 buttons on the remote  
control or on the projector to enter  
the preset keycode in “Old Code”.  
3
8
Selecting the Transmission  
Speed (RS-232C)  
When setting the keycode for the first time,  
press R on the projector for four times.  
PRJ - ADJ  
Make sure that both the projector and computer  
are set for the same baud rate.  
Setting the System Lock  
– – – –  
– – – –  
– – – –  
Old Code  
New Code  
Reconfirm  
Selectable  
Description  
items  
9600bps  
Transmission speed is slow.  
P
Note  
R
115200bps Transmission speed is rapid.  
• If you input a wrong keycode, the cursor  
returns to the first point of the “Old Code”.  
• The preset keycode is 4 R buttons on  
the projector. When you press the R but-  
ton four times, the keycord input screen  
disappears.  
9 Fan Mode Setting  
This function changes the fan rotation speed.  
Selectable  
Description  
items  
Press the 4 buttons on the remote  
control or on the projector to enter  
the new keycode in “New Code”.  
4
Normal  
High  
Suitable for normal environments.  
Select this when using the projector at  
altitudes of approximately 1,500  
meters (4,900 feet) or more.  
Note  
When “Fan Mode” is set to “High”, the fan rotation  
speeds up, and the fan noise becomes louder.  
• You cannot use the following buttons for  
keycode: STANDBY/ON, ON, STANDBY,  
ENTER  
and MENU/HELP  
,
L-CLICK, R-CLICK/RETURN  
0 System Lock Function  
System lock function recognizes each  
button on the remote control or on the  
projector as an individual button, even if  
they share the same button name. If you  
used the buttons on the projector in set-  
ting your keycode, the keycode cannot be  
canceled with the remote control.  
This function prevents unauthorized use of the  
projector. Once this function is activated, users  
must enter the correct keycode each time the  
projector is turned on. We suggest you record  
the keycode in a safe place where only au-  
thorized users have access.  
Info  
PRJ - ADJ  
Setting the System Lock  
If you lose or forget your keycode, contact  
your nearest Sharp Authorized Projector  
Dealer or Service Center (see page 65). Even  
if the product warranty is valid, the keycode  
reset will incur a charge.  
Old Code  
* * * *  
– – –  
– – – –  
New Code  
Reconfirm  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enter the same keycode in “Re-  
confirm”.  
Keylock Function  
5
Locking the Operation  
Buttons on the Projector  
Use this function to lock the operation buttons  
on the projector.  
Note  
To cancel the keycode that you have already  
set  
• Press R on the projector for four times in steps  
4 and 5 above.  
When the System Lock is set  
• When System Lock is set, the keycode input  
screen appears after the power is turned on.  
When it appears, enter the right keycode to  
start projection.  
a Locking the Operation Buttons  
Hold down ENTER on the projector for about 5  
seconds while the projector is being turned on.  
On-screen display  
Input screen for keycode  
• The keylock function does not affect the opera-  
tion with the remote control buttons.  
• You cannot use the keylock function while the  
projector is warming up.  
– – – –  
System Lock  
a Taking the Keylock off  
Hold down ENTER on the projector for about 5  
seconds.  
Checking the Lamp Life  
Status  
On-screen display  
You can confirm the cumulative lamp usage time  
and the remaining lamp life (percentage).  
Lamp usage condition  
Remaining lamp life  
• When the projector is in standby mode, you can  
release the keylock by holding down ENTER  
and STANDBY/ON on the projector simulta-  
neously for about 5 seconds.  
“Life”  
100%  
5%  
Operated exclusively  
with Lamp Setting set to X,XXX  
“Eco +Quiet”  
Approx.  
Approx.  
XXX hours  
hours  
Info  
Operated exclusively  
with Lamp Setting set to X,XXX  
“Bright”  
hours  
Approx.  
Approx.  
XXX hours  
• Keylock cannot be set while the projector is:  
displaying the “Setup Guide” or “Menu”  
screens, in standby mode, warming up, chang-  
ing input signals, operating “Auto Sync” func-  
tion, in “FREEZE” mode or on the “System  
Lock” screen during warming up.  
Note  
• It is recommended that the lamp be changed  
when the remaining lamp life becomes 5%.  
• The lamp life may vary depending on the us-  
age condition.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting with the “Help” Menu  
This function advises you to solve the problems during usage.  
Utilizing the “Help” Menu  
Functions  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
Example: When image flickering appears  
Operation to solve image flickering when pro-  
jecting the computer RGB signal.  
MENU/HELP  
button  
Press MENU/HELP.  
1
Press O or Q to selectHelp”, then  
2
Select “Initiate “Auto Sync” Ad-  
4
5
press ENTER.  
justments”, then press ENTER.  
If the image is not improved, se-  
lect “Adjust horizontal noise”,  
then press ENTER.  
Press P or R to select “Vertical  
3
stripes or flickering image ap-  
pears” on Help menu, then press  
ENTER.  
Press O or Q to adjust.  
6
Picture  
SCR - ADJ  
PRJ - ADJ  
Help  
Help  
Vertical stripes or flickering image appear  
There is no picture or audio  
Vertical stripes or flickering image appear  
Data image is not centered  
Color is faded or poor  
Phase  
SEL./ADJ.  
0
Rtn. Menu  
END  
Picture is dark  
Note  
The image is distorted  
You can adjust the items with check marks ().  
• The items in the “Help” menu change, de-  
pending on the input signal or setting that you  
have selected.  
Reset all adjustments to default settings  
If the problem is not solved, refer to  
“Troubleshooting” (see pages 63 and 64).  
• When selecting “sRGB” in “Picture Mode”, the  
item “Color is faded or poor” is not displayed.  
This means you cannot change input signal  
types.  
SEL.  
ENTER  
END  
Press ENTER.  
Help  
Vertical stripes or flickering image appear  
Initiate “Auto Sync” Adjustments.  
If there is no change after performing "Auto Sync"  
adjustments, adjust the following items.  
Adjust vertical noise  
Adjust horizontal noise  
Reset the 2 items above  
Return  
Signal Info  
1024ꢀ ꢀ ꢀ ꢀ 768  
59.9 Hz  
H
48.3 kHz  
/
V
SEL.  
ENTER  
END  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Cleaning the projector  
Cleaning the lens  
Ensure that you have unplugged the power  
cord before cleaning the projector.  
The cabinet as well as the operation panel is  
made of plastic. Avoid using benzene or  
thinner, as these can damage the finish on the  
cabinet.  
Use a commercially available blower or lens  
cleaning paper (for glasses and camera lenses)  
for cleaning the lens. Do not use any liquid type  
cleaning agents, as they may wear off the  
coating film on the surface of the lens.  
As the surface of the lens can easily get  
damaged, be careful not to scrape or hit the  
lens.  
Do not use volatile agents such as insecticides  
on the projector.  
Do not attach rubber or plastic items to the  
projector for long periods.  
The effects of some of the agents in the plastic  
may cause damage to the quality or finish of the  
projector.  
Wipe off dirt gently with a soft flannel cloth.  
When the dirt is hard to remove, soak a cloth in  
a mild detergent diluted with water, wring the  
cloth well and then wipe the projector.  
Strong cleaning detergents may discolor, warp  
or damage the coating on the projector. Make  
sure to test on a small, inconspicuous area on  
the projector before use.  
Cleaning the exhaust and intake vents  
Use a vacuum cleaner to clean dust from the  
exhaust vent and the intake vent.  
Mild detergent diluted  
with water  
Info  
• If you want to clean the air vents during projec-  
tor operation, ensure you press STANDBY/ON  
on the projector or STANDBY on the remote  
control and put the projector into standby  
mode. After the cooling fan has stopped, clean  
the vents.  
Thinner  
Wax  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance Indicators  
The warning lights (power indicator, lamp indicator and temperature warning indicator) on the  
projector indicate problems inside the projector.  
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate  
red, and the projector will enter standby mode. After the projector has entered standby mode,  
follow the procedures given below.  
Top View  
Temperature warning  
indicator  
Lamp indicator  
Power indicator  
About the temperature warning indicator  
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,  
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp  
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-  
tor will enter standby mode. After “  
” appears, ensure you perform the measures described on  
page 51.  
About the lamp indicator  
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be  
displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will  
automatically turn off and then the projector will automatically enter standby mode. At this time, the  
lamp indicator will illuminate in red.  
If you try to turn on the projector a fourth time without replacing the lamp, the projector will  
not turn on.  
Indicators on the Projector  
Power indicator  
Red on  
Normal (Standby)  
Green on  
Red blinks  
Normal (Power on)  
Abnormal (See page 51.)  
Green blinks Normal (Cooling)  
Green on Normal  
Green blinks The lamp is warming up.  
Lamp indicator  
Red on  
The lamp is shut down abnormally or requires to be  
changed. (See page 51.)  
Temperature warning Off  
indicator  
Normal  
Red on  
The internal temperature is abnormally high. (See page 51.)  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance indicator  
Problem  
Cause  
Possible Solution  
Normal  
Abnormal  
Tempera-  
ture  
warning  
indicator  
The internal  
temperature is  
abnormally  
high.  
Blocked air intake  
• Relocate the projector to  
an area with proper  
ventilation. (See page 8.)  
Off  
Red on  
(Standby)  
Cooling fan  
breakdown  
Internal circuit  
failure  
Take the projector to your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 65) for  
repair.  
Clogged air intake  
Lamp  
indicator  
The lamp does  
not illuminate.  
The lamp is shut  
down abnormally.  
• Disconnect the power cord  
from the AC outlet, and  
then connect it again.  
Green on  
(Green  
blinks  
Red on  
when the  
lamp is  
warming  
up or  
turning  
off.)  
Time to change  
the lamp.  
Remaining lamp life • Carefully replace the lamp.  
becomes 5% or  
less.  
(See page 52.)  
Take the projector to your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 65) for  
repair.  
The lamp does  
not illuminate.  
Burnt-out lamp  
Red on  
(Standby)  
Lamp circuit failure  
• Please exercise care when  
replacing the lamp.  
• Securely install the cover.  
Power  
indicator  
The power  
The lamp unit cover • If the power indicator blinks  
Green on/  
Red on  
Red  
blinks  
indicator blinks  
in red when the  
projector is on.  
is open.  
in red even when the lamp  
unit cover are securely  
installed, contact your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 65) for  
advice.  
Green  
blinks  
(Cooling)  
Info  
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the  
possible solutions above and then wait until the projector has cooled down completely before plug-  
ging in the power cord and turning the power back on. (At least 10 minutes.)  
• If the power is turned off for a brief moment due to power outage or some other cause while using  
the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-  
nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,  
replace the power cord in the AC outlet and then turn the power on again.  
• The cooling fan keeps the internal temperature of the projector constant and this function is con-  
trolled automatically. The sound of the cooling fan may change during operation because the fan  
speed may change and this is not a malfunction.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp  
Lamp  
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes  
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life  
(percentage) can be checked with the on-screen display. (See page 47.)  
Purchase a replacement lamp of type AN-F212LP from your place of purchase, nearest Sharp  
Authorized Projector Dealer or Service Center.  
IMPORTANT NOTE TO U.S. CUSTOMERS:  
The lamp included with this projector is backed by a 90-day parts and labor limited  
warranty. All service of this projector under warranty, including lamp replacement,  
must be obtained through a Sharp Authorized Projector Dealer or Service Center.  
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,  
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).  
Hg LAMP CONTAINS MERCURY For State Lamp Disposal  
Information  
U.S.A. ONLY  
Caution Concerning the Lamp  
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp  
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface  
scratches or deterioration of the lamp due to a lapse of usage time.  
The period of time up to failure largely varies depending on the individual lamp and/or the condition  
and the frequency of use. It is important to note that failure can often result in the bulb cracking.  
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended  
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating  
normally.  
Should the lamp break, there is also a possibility that glass particles may spread inside of the  
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector  
Dealer or Service Center to assure safe operation.  
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the  
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes  
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case  
of exposure to the gas, consult a doctor as soon as possible.  
Replacing the Lamp  
Caution  
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may  
cause burns or injury.  
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully  
cool before removing the lamp unit.  
Carefully change the lamp by following the instructions described in this section. * If you wish,  
you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service  
Center.  
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized  
Projector Dealer or Service Center for repair.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing and Installing  
the Lamp Unit  
Warning!  
• Do not remove the lamp unit from the projec-  
tor right after use. The lamp and parts around  
the lamp will be very hot and may cause burns  
or injury.  
Lamp unit  
AN-F212LP  
Optional  
accessory  
STANDBY/ON button  
Info  
• Do not touch the glass surface of the lamp  
unit or the inside of the projector.  
To avoid injury to yourself and damage to the  
lamp, make sure you carefully follow the steps  
below.  
• Do not loosen other screws except for the  
lamp unit cover and lamp unit.  
AC socket  
Press STANDBY/ONon the projec-  
1
tor or STANDBY on the remote  
control to put the projector into  
standby mode.  
User service screw  
(for lamp unit cover)  
• Wait until the cooling fan stops.  
Disconnect the power cord.  
• Unplug the power cord from the AC  
socket.  
2
1
• Leave the lamp until it has fully cooled  
down (about 1 hour).  
2
Remove the lamp unit cover.  
3
• Turn the projector over. Loosen the user  
service screw (1) that secures the lamp  
unit cover. Remove the lamp unit cover  
(2).  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp (Continued)  
Remove the lamp unit.  
4
• Loosen the securing screws from the  
lamp unit. Hold the lamp unit and pull it  
in the direction of the arrow. At this time,  
keep the lamp unit horizontal and do not  
tilt it.  
Insert the new lamp unit.  
5
• Press the lamp unit firmly into the lamp  
Securing screws  
unit compartment. Fasten the securing  
screws.  
Replace the lamp unit cover.  
• Align the tab on the lamp unit cover  
(1) and place it while pressing the tab  
(2) to close it. Then tighten the user ser-  
vice screw (3) to secure the lamp unit  
cover.  
6
Info  
• If the lamp unit and lamp unit cover are  
not correctly installed, the power will not  
turn on, even if the power cord is con-  
nected to the projector.  
Resetting the Lamp Timer  
Reset the lamp timer after replacing the lamp.  
Info  
• Make sure to reset the lamp timer only when  
replacing the lamp. If you reset the lamp timer  
and continue to use the same lamp, this may  
cause the lamp to become damaged or ex-  
plode.  
AC socket  
Connect the power cord.  
• Plug the power cord into the AC socket  
of the projector.  
1
STANDBY/ON  
button  
Reset the lamp timer.  
2
ENTER button  
• While simultaneously holding down  
MENU/HELP, ENTER and R on the pro-  
jector, press STANDBY/ON on the pro-  
jector.  
R button  
• “LAMP 0000H” is displayed, indicating  
that the lamp timer is reset.  
MENU/HELP  
button  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Pin Assignments  
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals : mini D-  
sub 15 pin female connector  
COMPUTER Input/Output  
Pin No. Signal  
1. Video input (red)  
2. Video input (green/sync on green)  
3. Video input (blue)  
4. Not connected  
COMPONENT Input/Output  
Pin No. Signal  
1. PR (CR)  
11  
15  
2.  
Y
3. PB (CB)  
4. Not connected  
5. Not connected  
6. Earth (PR)  
5. Not connected  
6. Earth (red)  
7. Earth (green/sync on green)  
8. Earth (blue)  
7. Earth (Y)  
8. Earth (PB)  
9. Not connected  
9. Not connected  
10. Not connected  
11. Not connected  
12. Not connected  
13. Not connected  
14. Not connected  
15. Not connected  
10. GND  
1
6
5
10  
11. Not connected  
12. Bi-directional data  
13. Horizontal sync signal: TTL level  
14. Vertical sync signal: TTL level  
15. Data clock  
DVI-D Terminal : 24 pin connector (XR-32X only)  
Pin No.  
Signal  
Pin No.  
Signal  
24  
17  
16. Hot plug detection  
17. T.M.D.S data 0–  
18. T.M.D.S data 0+  
19. T.M.D.S data 0 shield  
20. Not connected  
21. Not connected  
22. T.M.D.S clock shield  
23. T.M.D.S clock+  
24. T.M.D.S clock–  
1. T.M.D.S data 2–  
2. T.M.D.S data 2+  
3. T.M.D.S data 2 shield  
4. Not connected  
5. Not connected  
6. DDC clock  
7. DDC data  
8. Not connected  
9. T.M.D.S data 1–  
10. T.M.D.S data 1+  
11. T.M.D.S data 1 shield  
12. Not connected  
13. Not connected  
14. +5V power  
8
16  
1
9
15. Ground  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Pin Assignments (Continued)  
RS-232C Terminal : mini DIN 9 pin female connector  
8
Pin No. Signal  
Name  
I/O  
Reference  
1.  
Not connected  
9
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
RD  
SD  
Receive Data  
Send Data  
Input  
Output  
Connected to internal circuit  
Connected to internal circuit  
Not connected  
Connected to internal circuit  
Not connected  
Connected to CS in internal circuit  
Connected to RS in internal circuit  
Not connected  
7
SG  
Signal Ground  
6
3
RS  
CS  
Request to Send  
Clear to Send  
4
5
2
1
RS-232C Terminal : D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor  
1
5
Pin No. Signal  
Name  
I/O  
Reference  
Not connected  
Connected to internal circuit  
Connected to internal circuit  
Not connected  
Connected to internal circuit  
Not connected  
Connected to CS in internal circuit  
Connected to RS in internal circuit  
Not connected  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
RD  
SD  
Receive Data  
Send Data  
Input  
Output  
SG  
Signal Ground  
RS  
CS  
Request to Send  
Clear to Send  
6
9
RS-232C Cable recommended connection : D-sub 9 pin female connector  
Pin No. Signal  
Pin No.  
Signal  
5
1
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
CD  
RD  
SD  
ER  
SG  
DR  
RS  
CS  
CI  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
CD  
RD  
SD  
ER  
SG  
DR  
RS  
CS  
CI  
9
6
Note  
Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the  
controlling device (e.g. computer).  
Projector  
Pin No.  
Computer  
Pin No.  
4
5
6
4
5
6
USB Terminal : Type B USB connector  
4
3
Pin No. Signal  
Name  
1.  
2.  
3.  
4.  
VCC  
USB–  
USB+  
SG  
USB power  
USB data–  
USB data+  
Signal Ground  
1
2
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C Specifications and Commands  
Computer control  
A computer can be used to control the projector by connecting an RS-232C serial control  
cable (cross type, commercially available) to the projector. (See page 24 for connection.)  
Communication conditions  
Set the serial port settings of the computer to match that of the table.  
Signal format: Conforms to RS-232C standard.  
Baud rate*: 9,600 bps / 115,200 bps  
Data length: 8 bits  
Parity bit: None  
Stop bit: 1 bit  
Flow control: None  
*Set the projector’s baud rate to the same rate as used by the computer.  
Basic format  
Commands from the computer are sent in the following order: command, parameter, and  
return code. After the projector processes the command from the computer, it sends a re-  
sponse code to the computer.  
Command format  
C1 C2 C3 C4 P1 P2 P3 P4  
Return code (0DH  
)
Command 4-digit  
Parameter 4-digit  
Response code format  
Normal response  
Problem response (communication error or incorrect command)  
Return code (0DH  
)
O
K
Return code (0DH  
)
E
R
R
Info  
• When controlling the projector using RS-232C commands from a computer, wait for at least 30  
seconds after the power has been turned on, and then transmit the commands.  
• After sending an input selection or picture adjustment command and then receiving an “OK” re-  
sponse code, the projector may take some time to process the command. If a second command is  
sent while the projector is still processing the first command, you may receive an “ERR” response  
code. If this happens, try resending the second command.  
• When more than one code is being sent, send each command only after the response code for the  
previous command from the projector is verified.  
• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”  
“TLTM _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”  
- When the projector receives the special commands shown above:  
* The on-screen display will not disappear.  
* The “Auto Power Off” timer will not be reset.  
- The special commands are available for applications that require continuous polling.  
Note  
If an underbar (_) appears in the parameter column, enter a space.  
If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets  
under Control Contents.  
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.  
*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response  
code is received.  
*3 The Lamp Timer Reset command is available only in standby mode.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C Specifications and Commands (Continued)  
Commands  
Example: When turning on the projector, make the following setting.  
Computer  
Projector  
P
O
W
R
_
_
_
1
O
K
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
(or 30-second startup time)  
OK  
OK or ERR  
0
Power ON  
OK or ERR  
OK  
1
_
_
_
_
_
_
W
W
W
B
R
R
R
N
1
0
?
1
P
O
O
O
A
Power  
On  
Off  
Status  
P
P
T
?
_
?
_
?
_
Projector Condition  
0: Normal  
0: Normal  
1: Temp High  
8: Lamp Life 5% or less  
16: Lamp Burn-out  
32: Lamp Ignition Failure  
1: Temp High  
2: Fan Error  
4: Cover Open  
8: Lamp Life 5% or less  
16: Lamp Burn-out  
32: Lamp Ignition Failure  
64: Temp Abnormally High  
0:Off, 4:Lamp Error  
_
_
_
1
T
L
P
S
Status  
0:Off, 1:On, 2:Retry  
3:Waiting, 4:Lamp Error  
1:On, 2:Cooling  
1
Lamp  
Name  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0:Standby  
1
1
1
1
1
1
1
*
T
T
T
T
T
T
M
P
P
L
L
L
L
N
N
J
O
P
T
T
T
A
R
N
W
N
T
M
L
M
D
1
Power Status  
Quantity  
Usage Time(Hour)  
Usage Time(Minute)  
Life(Percentage)  
Model Name Check  
Model Name Check  
Projector Name Setting 1  
(First 4 characters) *1  
Projector Name Setting 2  
(Middle 4 characters) *1  
Projector Name Setting 3  
(Last 4 characters) *1  
Projector Name Check  
Computer  
0 – 9999(Integer)  
0, 15, 30, 45  
0% – 100%(Integer)  
XR32X/XR32S  
XR-32X/XR-32S  
OK or ERR  
*
*
*
*
*
*
*
*
*
*
*
P
P
J
J
N
N
2
3
OK or ERR  
OK or ERR  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
2
1
2
3
1
2
?
?
?
?
P
I
I
I
I
I
I
I
I
J
R
R
B
B
B
V
V
R
V
M
C
N
G
G
D
D
D
E
E
G
E
O
H
0
B
B
S
S
S
D
D
B
D
D
K
Projector Name  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
Input Change  
DVI  
DVI-D-Computer select *2  
DVI-D-Video select *2  
DVI-Analog select *2  
S-Video  
Video  
1: Computer, 2: DVI (XR-32X only) or ERR ERR  
1: S-Video, 2: Video or ERR ERR  
?
?
?
?
?
?
?
?
?
?
?
?
Input RGB Check  
Input Video Check  
Input Mode Check  
Input Check  
I
I
I
1: RGB, 2: Video  
1: Computer  
2: DVI (XR-32X only)  
3: S-Video  
ERR  
ERR  
4: Video  
_
_
_
*
*
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
*
*
*
V
V
K
I
O
O
E
M
M
R
R
D
A
A
A
A
A
A
A
B
B
B
B
B
B
B
L
U
Y
B
B
E
E
J
S
S
S
S
S
S
S
S
S
S
S
S
S
S
A
D
S
K
K
Z
*
*
*
Volume  
Volume(0 – 60)  
Volume up/down(-10 – +10)  
-80 – +80 (XGA)/-40 – +40 (SVGA)  
On  
Off  
On  
Off  
Start  
*
_
Keystone  
AV Mute  
_
_
1
0
1
0
1
1
2
3
5
6
0
1
1
2
3
5
6
0
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
I
F
F
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Freeze  
Z
S
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Auto Sync  
Resize  
Normal  
Stretch  
Dot By Dot  
Full  
Border  
Area Zoom  
V-Stretch  
Normal  
Stretch  
Dot By Dot  
Full  
Computer  
1
1
_
_
_
_
_
DVI  
Border  
Area Zoom  
V-Stretch  
1
1
is only for XR-32X.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
OK or ERR  
(or 30-second startup time)  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
2
3
0
1
1
2
3
0
1
1
0
1
2
3
4
*
*
*
*
*
*
*
*
*
0
1
2
0
1
2
1
0
1
2
1
2
0
1
2
3
4
*
*
*
*
*
*
*
*
*
Resize  
S-Video  
Normal  
R
R
R
R
R
R
R
R
R
R
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
A
A
A
A
A
B
B
B
B
B
L
S
S
S
S
S
S
S
S
S
S
R
P
P
P
P
P
P
B
R
B
C
T
S
C
W
I
V
V
V
V
V
V
V
V
V
V
E
S
S
S
S
S
I
R
D
E
O
I
H
T
E
P
P
P
R
R
R
E
I
Stretch  
Border  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
Area Zoom  
V-Stretch  
Normal  
1
1
_
_
_
Video  
Stretch  
Border  
Area Zoom  
V-Stretch  
1
1
_
ALL Reset  
Computer INPUT  
Picture Mode Standard  
Presentation  
1
1
1
1
1
*
*
*
*
*
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
M
M
M
Movie  
Game  
sRGB  
Contrast  
Bright  
Red  
Blue  
Color  
Tint  
Sharp  
CLR Temp  
Bright Boost  
Progressive  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2  
_
_
_
_
_
_
_
_
_
_
_
_
2D Progressive  
3D Progressive  
Film Mode  
Off  
I
I
DNR  
N
N
N
R
S
S
S
A
A
P
P
P
P
P
P
B
R
B
C
T
S
C
W
I
Level 1  
Level 2  
Picture Reset  
Signal Type  
Auto  
RGB  
I
I
I
I
I
I
Compontent  
Audio 1  
Audio 2  
Audio Input  
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
DVI INPUT  
Picture Mode Standard  
Presentation  
S
S
S
S
S
I
R
D
E
O
I
H
T
E
P
P
P
R
R
R
E
I
1
1
1
1
1
*
*
*
*
*
Movie  
Game  
sRGB  
Contrast  
Bright  
Red  
Blue  
Color  
Tint  
Sharp  
CLR Temp  
Bright Boost  
Progressive  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
*
*
*
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
2
0
1
2
1
0
1
2
1
2
0
1
2
2D Progressive  
3D Progressive  
Film Mode  
Off  
I
I
DNR  
N
N
N
R
S
S
S
A
A
B
B
B
Level 1  
Level 2  
Picture Reset  
Signal Type  
Auto  
RGB  
I
I
I
I
I
I
Compontent  
Audio 1  
Audio 2  
Audio Input  
R
R
H
H
H
Dynamic Range Auto  
Standard  
Enhanced  
D
D
D
is only for XR-32X.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C Specifications and Commands (Continued)  
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
OK or ERR  
(or 30-second startup time)  
_
_
_
_
_
_
_
_
_
_
_
S-Video INPUT  
Picture Mode Standard  
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
I
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
N
N
A
A
A
P
P
P
P
P
B
R
B
C
T
S
C
W
I
S
S
S
S
I
R
D
E
O
I
H
T
E
P
P
P
R
R
R
E
I
1
1
1
1
*
*
*
*
*
0
1
2
3
*
*
*
*
*
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
Presentation  
Movie  
Game  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
Contrast  
Bright  
Red  
Blue  
Color  
Tint  
Sharp  
CLR Temp  
Bright Boost  
Progressive  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
*
*
_
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2  
_
_
_
_
_
_
_
_
_
2D Progressive  
3D Progressive  
Film Mode  
Off  
Level 1  
Level 2  
0
1
2
0
1
2
1
1
2
0
1
2
3
*
*
*
*
*
*
*
*
*
0
1
2
0
1
2
1
1
2
1
0
*
*
*
*
*
*
2
*
*
*
I
I
DNR  
N
N
N
R
A
A
P
P
P
P
P
B
R
B
C
T
S
C
W
I
Picture Reset  
Audio Input  
Audio 1  
Audio 2  
I
Video INPUT  
Picture Mode Standard  
Presentation  
S
S
S
S
I
R
D
E
O
I
H
T
E
P
P
P
R
R
R
E
I
1
1
1
1
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
Movie  
Game  
Contrast  
Bright  
Red  
Blue  
Color  
Tint  
Sharp  
CLR Temp  
Bright Boost  
Progressive  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2  
2D Progressive  
3D Progressive  
Film Mode  
Off  
Level 1  
Level 2  
I
I
DNR  
N
N
N
R
A
A
C
C
H
H
H
H
H
H
R
S
S
S
S
S
S
R
V
V
V
V
V
V
R
R
C
P
H
V
R
Picture Reset  
Audio Input  
Audio 1  
Audio 2  
I
C.M.S. Setting  
C.M.S.  
On  
Off  
Hue  
S
S
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
E
L
1
0
*
*
*
*
*
*
_
*
*
*
*
*
Red  
Yellow  
Green  
Cyan  
Blue  
*
_
Magenta  
Reset  
Red  
Yellow  
Green  
Cyan  
Saturation  
*
*
*
*
*
*
*
*
*
*
*
*
*
3
*
*
*
*
*
Blue  
*
_
*
_
Magenta  
Reset  
Red  
Yellow  
Green  
Cyan  
Blue  
Magenta  
Reset  
Value  
*
*
*
*
*
*
_
_
*
*
*
*
*
*
_
_
*
4
1
*
*
*
C.M.S. All Reset  
-150 – +150  
-30 – +30  
-150 – +150  
-60 – +60  
Clock  
Phase  
H-position  
V-position  
*
_
*
*
*
*
*
*
I
I
I
I
H
P
P
E
*
_
*
*
*
_
_
_
Fine Sync Adjustment Reset  
1
is only for XR-32X.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
OK or ERR  
(or 30-second startup time)  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
OK or ERR  
_
*
*
*
Image Shift  
OSD Display  
-96 – +96 (XGA)/-75 – +75 (SVGA)  
On  
Off  
Off  
CC1  
CC2  
Auto  
PAL  
SECAM  
NTSC4.43  
NTSC3.58  
PAL-M  
PAL-N  
PAL-60  
Logo  
Blue  
None  
Bright  
Eco + Quiet  
On  
L
I
N
M
M
L
L
L
D
D
D
C
C
C
S
S
S
S
S
S
S
S
B
B
B
M
M
D
D
O
O
E
E
U
U
R
R
I
S
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
1
1
1
1
_
_
_
_
_
_
_
_
_
_
0
1
0
0
1
2
1
2
3
4
5
6
7
8
1
3
4
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
1
0
1
0
1
0
1
2
0
1
1
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
kHz(***.* or ERR)  
Hz(***.* or ERR)  
OK or ERR  
OK or ERR  
ERR  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
I
I
Closed Caption  
Video System  
C
C
C
M
M
M
M
M
M
M
M
I
A
A
A
Y
Y
Y
Y
Y
Y
Y
Y
G
G
G
D
D
J
E
E
E
E
E
E
E
E
M
M
M
H
H
A
A
P
P
R
R
O
O
M
M
M
M
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
S
S
S
S
F
Background  
I
I
Lamp Setting  
Auto Sync  
T
T
A
A
A
A
A
A
M
M
I
Off  
On  
Off  
On  
Off  
Standard  
Eco  
J
Auto Power Off  
Auto Restart  
STANDBY Mode  
PRJ Mode  
W
W
S
S
T
T
Reverse  
On  
Off  
On  
Off  
E
E
N
N
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
U
U
D
D
K
K
Q
Q
D
D
E
I
I
I
Invert  
I
Language  
English  
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
S
S
S
S
A
A
T
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Svenska  
Português  
polski  
Türkçe  
Magyer  
On  
Off  
On  
Off  
On  
Off  
Horizontal  
Vertical  
Normal  
High  
L
Setup Guide  
G
G
N
N
P
P
R
R
M
M
R
System Sound  
Internal Speaker  
RGB Frequency  
Check  
Fan Mode  
T
F
L
L
P
H
H
L
0
Lamp Timer Reset *3  
0
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Computer Compatibility Chart  
Computer  
• Multiple signal support  
Horizontal Frequency: 15-70 kHz,  
Vertical Frequency: 45-85 Hz,  
Pixel Clock: 12-108 MHz  
Sync signal: Compatible with TTL level  
• Compatible with sync on green signal  
The following is a list of modes that conform to VESA. However, this projector supports other  
signals that are not VESA standards.  
Vertical Frequency  
(Hz)  
*DVI-D  
Support  
Horizontal Frequency  
(kHz)  
Resolution  
640 × 350  
VESA Standard  
Display  
PC/MAC  
27.0  
31.5  
37.5  
27.0  
31.5  
37.9  
27.0  
31.5  
27.0  
31.5  
37.9  
26.2  
31.5  
34.7  
37.9  
37.5  
43.3  
31.4  
35.2  
37.9  
46.6  
48.1  
46.9  
53.7  
40.3  
48.4  
56.5  
60.0  
68.7  
45.0  
47.8  
49.7  
62.8  
47.7  
47.8  
55.0  
66.2  
67.5  
64.0  
64.0  
34.9  
49.7  
60.2  
68.7  
60  
70  
85  
60  
70  
85  
60  
70  
60  
70  
85  
50  
60  
70  
72  
75  
85  
50  
56  
60  
70  
72  
75  
85  
50  
60  
70  
75  
85  
60  
60  
60  
75  
60  
60  
60  
70  
75  
60  
60  
67  
75  
75  
75  
640 × 400  
720 × 350  
720 × 400  
VGA  
Upscale  
640 × 480  
SVGA  
XGA  
800 × 600  
PC  
1024 × 768  
True  
1280 × 720  
1280 × 768  
1280 × 800  
1280 × 800  
1360 × 768  
1366 × 768  
WXGA  
SXGA  
Intelligent  
Compression  
1152 × 864  
1280 × 1024  
1400 × 1050  
640 × 480  
SXGA+  
VGA  
SVGA  
XGA  
MAC 13"  
MAC 16"  
MAC 19"  
MAC 21"  
Upscale  
832 × 624  
1024 × 768  
True  
SXGA 1152 × 870  
Intelligent Compression  
* XR-32X only  
Note  
When this projector receives 640K350 VESA format VGA signals, “640 × 400” appears on the screen.  
Optimum image quality will be achieved by matching your computer’s output resolution to the reso-  
lution that corresponds to “True” in the “Display” column shown above.  
Signal  
480I  
480P  
540P  
576I  
576P  
720P  
720P  
1035I  
1080I  
1080I  
Horizontal Frequency (kHz) Vertical Frequency (Hz)  
*
DVI-D Support (Compatible with HDCP)  
DTV  
15.7  
31.5  
33.8  
15.6  
31.3  
37.5  
45.0  
33.8  
28.1  
33.8  
60  
60  
60  
50  
50  
50  
60  
60  
50  
60  
* XR-32X only  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Problem  
Check  
Page  
• Projector power cord is not plugged into the wall outlet.  
• Power to the external connected devices is off.  
• The selected input mode is wrong.  
24  
29  
• Cables are incorrectly connected to the projector.  
• Remote control battery has run out.  
21–24  
14  
External output has not been set when connecting notebook computer. 21  
No picture and no sound  
or projector does not  
start.  
• The lamp unit cover is not installed correctly.  
53, 54  
21  
XR-32X only: If the connected DVI digital equipment is turned on  
before the “DVI-D” input mode is selected on the projector, the image  
may not be projected properly or may not be displayed at all. Ensure  
that the appropriate input mode has been selected on the projector  
before you turn on the connected equipment.  
• Cables are incorrectly connected to the projector.  
• “Bright” is set to minimum position.  
21–24  
41  
• Depending on the computer you are using, an image may not be  
projected unless Xthe signal output setting of the computer is  
switched to the external output. Refer to the computer’s operation  
manual for how to switch its signal output settings.  
Sound is heard but no  
picture appears  
(or picture is dark).  
• Image adjustments are incorrectly set.  
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower  
the “Bright Boost” value.  
(Video Input only)  
• Video input system is incorrectly set.  
41  
48  
Color is faded or poor.  
• Adjust the focus.  
• The projection distance exceeds the focus range.  
26  
20  
There is fog on the lens. If the projector is carried from a cold room into a  
warm room, or if it is suddenly heated, condensation may form on the  
surface of the lens and the image will become blurred. Set up the  
projector at least one hour before it is to be used. If condensation should  
form, remove the power cord from the wall outlet and wait for it to clear.  
Picture is blurred;  
noise appears.  
(Computer Input only)  
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)  
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)  
• Noise may appear depending on the computer.  
48  
48  
• Cables are incorrectly connected to the projector.  
21–24  
• Volume is set to minimum.  
29  
• When the projector is connected to an external device and the  
volume is set to minimum, the sound is not output even if you turn up  
the volume of the external device.  
Picture appears but no  
sound is heard.  
• “Speaker” is set to “Off”.  
45  
Data image is not  
centered.  
• Select “Data image is not centered” in the “Help” menu and make the 48  
necessary adjustments.  
• Depending on the computer you are using, the output resolution  
signal may be different from the one you have set. For details, refer to  
the operation manual of the computer.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting (Continued)  
Problem  
Check  
Page  
An unusual sound is  
occasionally heard from  
the cabinet.  
• If the picture is normal, the sound is due to cabinet shrinkage caused  
by room temperature changes. This will not affect operation or  
performance.  
Maintenance indicator on • See “Maintenance Indicators”.  
the projector illuminates  
50  
47  
or blinks in red.  
The projector cannot  
be turned on or put into  
the standby mode  
• The keylock is set.  
If the keylock is set to “ON”, all the buttons are locked.  
using STANDBY/ON on  
the projector.  
Picture is green on  
COMPUTER  
(Component)/  
• Change the input signal type setting.  
48  
40, 48  
• When you cannot select an input signal type, select “Color is faded  
or poor” in the “Help” menu, after selecting an item other than  
“sRGB” in “Picture Mode”, and then select an input signal type.  
*DVI (Component).  
Picture is pink  
(no green) on  
COMPUTER (RGB)/  
*DVI (RGB).  
Picture is too bright and • Image adjustments are incorrectly set.  
whitish.  
41  
The cooling fan becomes • When temperature inside the projector increases, the cooling fan  
8, 9  
49, 50, 51  
noisy.  
runs faster.  
The lamp does not light • The lamp indicator is illuminating in red.  
up even after the  
projector turns on.  
Replace the lamp.  
50, 53  
The lamp suddenly turns  
off during projection.  
The image sometimes  
flickers.  
• Cables are incorrectly connected to the projector or the connected  
equipment works improperly.  
• Select “Vertical stripes or flickering image appear” in the “Help”  
menu and make the necessary adjustments.  
21–24  
48  
• If this happens frequently, replace the lamp.  
53  
53  
The lamp needs much • The lamp will eventually need to be changed.  
time to turn on.  
While the remaining lamp life draws to a close, replace the lamp.  
Picture is dark.  
The remote control  
cannot be used.  
• Operate the remote control while pointing it at the projector’s remote  
control sensor.  
• The remote control may be too far away from the projector.  
• If direct sunlight or a strong fluorescent lamp is shining on the  
projector’s remote control sensor, place the projector where it will not  
be affected by strong light.  
15  
• The batteries may be depleted or inserted incorrectly. Make sure the 14  
batteries are inserted correctly or insert new ones.  
* XR-32X only  
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation  
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For SHARP Assistance  
If you encounter any problems during setup or operation of this projector, first  
refer to theTroubleshootingsection on pages 63 and 64. If this operation manual  
does not answer your question, please contact the SHARP Service departments  
listed below.  
U.S.A.  
Sharp Electronics Corporation  
1-888-GO-SHARP (1-888-467-4277)  
Benelux  
SHARP Electronics Benelux BV  
0900-SHARPCE (0900-7427723)  
Nederland  
9900-0159 Belgium  
Canada  
Mexico  
Sharp Electronics of Canada Ltd.  
(905) 568-7140  
Australia  
Sharp Corporation of Australia Pty.  
Ltd.  
1300-135-022  
Sharp Electronics Corporation  
Mexico Branch  
(525) 716-9000  
New Zealand Sharp Corporation of New Zealand  
(09) 634-2059, (09) 636-6972  
Latin America Sharp Electronics Corp. Latin  
American Group  
(305) 264-2277  
Singapore  
Hong Kong  
Taiwan  
Sharp-Roxy Sales (S) Pte. Ltd.  
65-226-6556  
Germany  
U.K.  
Sharp Electronics (Europe) GMBH  
01805-234675  
Sharp-Roxy (HK) Ltd.  
(852) 2410-2623  
Sharp Electronics (U.K.) Ltd.  
08705 274277  
Sharp Corporation (Taiwan)  
0800-025111  
Italy  
Sharp Electronics (Italy) S.P.A.  
(39) 02-89595-1  
Malaysia  
U.A.E.  
Sharp-Roxy Sales & Service Co.  
(60) 3-5125678  
France  
Sharp Electronics France  
01 49 90 35 40  
Sharp Middle East Fze  
971-4-81-5311  
Spain  
Sharp Electronica Espana, S.A.  
93 5819700  
Thailand  
Korea  
Sharp Thebnakorn Co. Ltd.  
02-236-0170  
Switzerland  
Sweden  
Austria  
Sharp Electronics (Schweiz) AG  
0041 1 846 63 11  
Sharp Electronics Incorporated of  
Korea  
(82) 2-3660-2002  
Sharp Electronics ( Nordic ) AB  
(46) 8 6343600  
India  
Sharp Business Systems (India)  
Limited  
(91) 11- 6431313  
Sharp Electronics (Europe) GMBH  
Branch Office Austria  
0043 1 727 19 123  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
XR-32X  
XR-32S  
0.55" DLP® Chip  
XGA (1024×768)  
F 2.5 – 2.6  
Display devices  
Resolution  
SVGA (800×600)  
Lens  
F number  
Zoom  
Manual, ×1.15 (f = 20.4 – 23.5 mm)  
Focus  
Manual  
Input terminals  
DVI-D (Compatible with HDCP)  
RGB/Component (mini D-sub 15 pin)  
S-Video (mini DIN 4 pin)  
Video (RCA)  
×1  
×1  
×1  
×1  
Audio (ø3.5 mm stereo minijack)  
Audio (RCA)  
×1  
×1 (L/R)  
×1  
Output terminals RGB/Component (mini D-sub 15 pin)  
Audio (ø3.5 mm stereo minijack)  
×1 (variable audio output)  
Control, others  
USB (Type B)  
×1  
RS-232C (mini DIN 9 pin)  
×1  
Speakers  
2 W (Mono)  
Projection lamp  
Rated voltage  
Rated frequency  
Input current  
200 W  
AC 100 – 240 V  
50/60 Hz  
2.9 A  
Power consumption (Standby)  
267 W (5.0 W) with AC 100 V  
259 W (5.7 W) with AC 240 V  
41°F to 95°F (+5°C to +35°C)  
Plastic  
10 41/64" × 3 33/64" × 10 7/16"  
(270 (W) × 89 (H) × 265 (D) mm)  
Operation temperature  
Cabinet  
Dimensions (main body only) [W × H × D]  
6.4 lbs. (2.9 kg)  
Weight (approx.)  
As a part of policy of continuous improvement, SHARP reserves the right to make design and  
specification changes for product improvement without prior notice. The performance specifica-  
tion figures indicated are nominal values of production units. There may be some deviations from  
these values in individual units.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Units: inches (mm)  
2 61/64 (75)  
10 41/64 (270)  
2 3  
/8 (60)  
M4  
M4  
M4  
M4  
13/32 (10)  
13/32 (10)  
1 27/64  
(36)  
2 61/64 (75)  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Accessories ............................................................. 10  
AC socket ................................................................ 24  
Adjustment buttons ................................................. 38  
AREA ZOOM ........................................................... 31  
Aspect ratio ............................................................. 30  
Audio Input .............................................................. 46  
AUDIO 1, 2 terminal ................................................ 23  
AUDIO OUT terminal .............................................. 23  
Auto Power Off ........................................................ 45  
Auto Restart ............................................................ 45  
Auto Sync (Auto Sync adjustment) ....... 33, 37, 45, 48  
AUTO SYNC button ................................................. 33  
AV MUTE button ...................................................... 29  
L-CLICK button ........................................................ 34  
Lens Cap ................................................................. 11  
MAGNIFY buttons ................................................... 33  
MENU/HELP button .......................................... 38, 48  
MONITOR OUT terminal ......................................... 23  
MOUSE/Adjustment buttons ............................. 34, 38  
NORMAL ........................................................... 30, 31  
ON button ................................................................ 25  
Optional accessories ............................................... 10  
OSD Display ............................................................ 43  
PAGE DOWN button................................................ 34  
PAGE UP button ...................................................... 34  
PDF ............................................................................ 9  
Picture Adjustment .................................................. 40  
Picture Mode ..................................................... 33, 40  
PICTURE MODE button .......................................... 33  
POINTER button ..................................................... 32  
Power cord ............................................................... 24  
Power indicator ........................................................ 50  
PRJ - ADJ ................................................................ 45  
PRJ Mode .......................................................... 19, 44  
Progressive .............................................................. 42  
Background ............................................................. 44  
Batteries .................................................................. 14  
Blue .......................................................................... 41  
BORDER ........................................................... 30, 31  
BREAK TIMER button ............................................. 32  
Bright ....................................................................... 41  
Bright Boost ............................................................. 41  
Closed Caption ........................................................ 44  
CLR Temp (Color Temperature) .............................. 41  
C.M.S. ...................................................................... 41  
Color ........................................................................ 41  
COMPUTER button ................................................. 29  
COMPUTER/COMPONENT input terminal ...... 21, 22  
Contrast ................................................................... 41  
R-CLICK/RETURN button ................................. 34, 38  
Rear adjustment foot ............................................... 27  
Red .......................................................................... 41  
Remote control ........................................................ 13  
Remote control sensor ............................................ 15  
Replacing the lamp ........................................... 52, 53  
Resize ................................................................ 30, 43  
RESIZE button ........................................................ 30  
RGB cable ............................................................... 21  
RS-232C terminal .................................................... 24  
DNR ......................................................................... 42  
DOT BY DOT ........................................................... 30  
DVI button ................................................................ 29  
DVI-D input terminal .......................................... 21, 22  
ECO+QUIET button ................................................ 32  
ENTER button ......................................................... 38  
Exhaust vent ...................................................... 12, 49  
SCR - ADJ ............................................................... 43  
Screen Size and Projection Distance ..................... 20  
Setup Guide....................................................... 26, 44  
Sharp ....................................................................... 41  
Speaker ................................................................... 45  
SPOT button ............................................................ 32  
STANDBY button ..................................................... 25  
STANDBY Mode ...................................................... 45  
STANDBY/ON button .............................................. 25  
STRETCH .......................................................... 30, 31  
Supplied accessories .............................................. 10  
S-VIDEO button ....................................................... 29  
S-VIDEO terminal .................................................... 22  
System Lock ............................................................ 46  
System Sound ......................................................... 45  
Fan Mode ................................................................. 46  
Fine Sync ................................................................. 48  
Focus ring ................................................................ 26  
FREEZE button ....................................................... 33  
Front adjustment foot .............................................. 27  
FULL ........................................................................ 30  
HEIGHT ADJUST lever ........................................... 27  
Help ......................................................................... 48  
H-Pos ................................................................. 37, 48  
Image shift ............................................................... 43  
INPUT modes .......................................................... 29  
Intake vent ......................................................... 11, 49  
Kensington Security Standard connector ............... 12  
Keycode ................................................................... 46  
Keylock .................................................................... 47  
KEYSTONE button .................................................. 28  
Keystone Correction .......................................... 28, 43  
Temperature warning indicator ............................... 50  
Tint ........................................................................... 41  
USB terminal ........................................................... 34  
VIDEO button .......................................................... 29  
VIDEO terminal ....................................................... 22  
VOL (Volume) buttons ............................................. 29  
V-Pos ................................................................. 37, 48  
V-STRETCH ............................................................ 31  
Lamp ........................................................................ 52  
Lamp indicator ......................................................... 50  
Lamp Setting ........................................................... 42  
Lamp Timer (Life) .................................................... 47  
Lamp unit ................................................................. 53  
Language (on-screen display language) ................ 44  
Zoom ring ................................................................ 26  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sierra Wireless Modem 2120028 User Manual
Sony Battery Charger BC VM50 User Manual
Sony Camcorder Accessories VCT 1500L User Manual
Sony CD Player NSX HMA56 User Manual
Sony VCR SVT 168 User Manual
Speco Technologies Computer Monitor M17LCBVH3 User Manual
StarTechcom Switch SV431USBAE User Manual
StarTechcom TV Converter Box S3510BMU33 User Manual
Stiga Lawn Mower 13 2501 19 User Manual
Sunfire Speaker Solitaire 10 User Manual