OPERATION MANUAL
MODEL
-
PG C30XU
LCD PROJECTOR
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the LCD projector, please read this operation manual carefully.
OPERATION MANUAL
ENGLISH
IMPORTANT
For your assistance in reporting the loss or theft of your
-
Model No.: PG C30XU
Color LCD Projector, please record the Serial Number
located on the bottom of the projector and retain this
information. Before recycling the packaging, please be
sure that you have checked the contents of the carton
thoroughly against the list of “Supplied Accessories”
on page 10.
Serial No.:
There are two important reasons for prompt warranty registration of your new SHARP LCD Projector,
using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
See bottom of actual set.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
SERVICE SCREW.
persons.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-
ference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the operation manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the interference at his own
expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
U.S.A. ONLY
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure your
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to
defeat the safeguards incorporated into this LCD Projector, observe the following basic rules for its installation, use and
servicing. For your own protection and reliable usage of your LCD Projector, please be sure to read these “IMPORTANT
SAFEGUARDS” carefully before use.
1. Read Instructions
13. Power-Cord Protection
All the safety and operating instructions should be read
before the product is operated.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.
2. Retain Instructions
The safety and operating instructions should be retained
for future reference.
14. Lightning
3. Heed Warnings
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
15. Overloading
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
6. Attachments
16. Object and Liquid Entry
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
7. Water and Moisture
Do not use this product near water–for example, near a
bathtub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
17. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
8. Accessories
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to
the product. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
e. If the product has been dropped or damaged in any
way.
f. If the product exhibits a distinct change in
performance, this indicates a need for service.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product and
to protect it from overheating. The openings should never
be covered or blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating
condition.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type
plug.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Outstanding Features
X
1. ADVANCED COMPATIBILITY WITH HIGH-END WORKSTATIONS
AND PCS
L
H
Compatible with up to 200 Hz vertical refresh rate, Sync on Green and Composite Sync signals
for use with a wide variety of high-end PCs and Workstations. (Page 11)
2. FOR USE WITH DTV
Allows projection of DTV images and 16:9 wide-screen images when connected to a DTV decoder
or similar video systems. (Page 13)
3. ADVANCED VIDEO CIRCUITRY
Provides high quality images with minimal dot crawl and cross color noise.
4. 3D DIGITAL UNIFORMITY
Equipped with new 3D digital uniformity technology for a clearer, more uniform image.
5. ANTI-ALIASING DIGITAL KEYSTONE CORRECTION
Digitally adjusts an image that is projected at an angle while maintaining image quality and
brightness. (Page 19)
6. DIGITAL IMAGE SHIFT FUNCTION
Allows digital adjustment of 16:9 wide-screen images up or down for easier viewing. (Page 20)
7. EASY-TO-USE GRAPHICAL USER INTERFACE (GUI)
A multi-color, icon-based menu system allows for simple image adjustments. (Page 23)
8. USER-FRIENDLY DESIGN
The two-color design along with an intuitive Graphical User Interface (GUI) makes this projector
very easy to set up and adjust.
9. AUTO SYNC TECHNOLOGY FOR AUTOMATIC IMAGE
PERFECTION
Automatically makes any necessary adjustments for perfectly synced computer images. (Page 32)
10. INTELLIGENT COMPRESSION AND EXPANSION
By using intelligent resizing technology, this projector can display higher and lower resolution images in detail without
compromising quality. (Page 36)
11. XGA RESOLUTION FOR HIGH RESOLUTION PRESENTATIONS
With XGA (1,024
ן 768) resolution, this projector can display very detailed presentation information. 12. UXGA COMPATIBLE
UXGA (1,600
ן 1,200) resolution images are intelligently resized to 1,024 ן 768 for full-screen or default presentations. 13. CUSTOMIZABLE STARTUP SCREEN
Allows you to load a custom startup image (i.e. your company logo) to be displayed while the projector is warming up.
(Page 38)
14. BUILT-IN PRESENTATION TOOLS
A variety of helpful presentation utilities are incorporated to enhance presentations. These include “Stamp” functions, “Break
Timer”, and “Digital Image Magnification”. (Page 43)
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Information
Useful Features
IMPORTANT SAFEGUARDS ……………………
Outstanding Features ……………………………
Contents ……………………………………………
Usage Guidelines …………………………………
How to Access the PDF Operation Manuals
(for Windows and Macintosh) ………………
For SHARP Assistance (U.S.A. only) …………
Part Names …………………………………………
2
3
4
5
Freeze Function …………………………………… 33
Digital Image Magnification …………………… 34
Gamma Correction ……………………………… 35
Selecting the Picture Display Mode …………… 36
Black Screen Function …………………………… 37
On-screen Display Override Function ………… 37
Selecting a Background Image ………………… 38
Selecting a Startup Image ……………………… 38
Economy Mode …………………………………… 39
Password …………………………………………… 40
Selecting the Keylock Level …………………… 41
Checking the Lamp UsageTime ……………… 41
Reverse/Invert Image Function ………………… 42
Using the Presentation Tools …………………… 43
Status Function …………………………………… 44
6
6
7
Setup & Connections
Supplied Accessories …………………………… 10
Connecting the Projector ……………………… 11
Operation
Maintenance & Troubleshooting
Basic Operations ………………………………… 16
Setting up the Screen …………………………… 18
Operating the Wireless Mouse from the
Remote Control ……………………………… 21
Using the GUI (Graphical User Interface)
Menu Screens ………………………………… 23
Selecting the On-screen Display Language … 25
Selecting the Video Input System Mode
(INPUT 3 (VIDEO) mode only) ……………… 25
Picture Adjustments ……………………………… 26
Adjusting the Picture …………………………… 26
Adjusting the Color Temperature …………… 27
Selecting the Signal Type……………………… 27
I/P Conversion ………………………………… 28
Audio Adjustments ……………………………… 28
Computer Image Adjustments
Air Filter Maintenance …………………………… 46
Lamp/Maintenance Indicators ………………… 47
Replacing the Projection Lamp ………………… 48
Using the Kensington Lock …………………… 49
Troubleshooting …………………………………… 49
Appendix
Optional Lenses …………………………………… 50
Transporting the Projector ……………………… 50
Connection Pin Assignments…………………… 51
RS-232C Port Specifications …………………… 52
Computer Compatibility Chart ………………… 54
Specifications ……………………………………… 55
Dimensions ………………………………………… 56
Guide to Effective Presentations ……………… 57
Glossary …………………………………………… 61
Index ………………………………………………… 62
(INPUT 1 or 2 mode only) …………………… 29
Adjusting the Computer Image ……………… 29
Saving and Selecting Adjustment Settings … 30
Special Mode Adjustment …………………… 31
Checking the Input Signal …………………… 31
Auto Sync Adjustment ………………………… 32
Auto Sync Display Function…………………… 32
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Usage Guidelines
"COMPLIES WITH 21 CFR SUBCHAPTER J"
Cautions Concerning the Laser Pointer
SHARP ELECTRONICS CORPORATION
CAUTION
DO NOT STARE INTO BEAM
WAVE LENGTH : 650nm
MAX. OUTPUT : 1mW
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
TEL : 1-800-BE-SHARP
U.S.A. ONLY
LASER RADIATION-
REMOTE CONTROL
MODEL NO. : RRMCG1579CESA
DC3V (1.5VX2PCS.)
The laser pointer on the remote control emits a laser beam from the laser
pointer window. This is a Class II laser which may impair your sight if directed
into the eyes. The three marks shown on the left are caution labels for the
laser beam.
• Do not look into the laser pointer window or shine the laser beam on yourself
or others. (The laser beam used in this product is harmless when directed
onto the skin. However, be careful not to project the beam directly into the
eyes.)
MADE IN CHINA
CLASS II LASER PRODUCT FABRIQUÉ AU CHINE
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
• Always use the laser pointer at temperatures between 41°F and 104°F
(
ם 5°C and ם 40°C). • Use of controls or adjustments, or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
Laser pointer
window
Cautions Concerning the Setup of the Projector
104˚F
(
ם 40˚C) For minimal servicing and to maintain high image quality, SHARP recommends
that this projector be installed in an area free from humidity, dust and cigarette
smoke. When the projector is subjected to these environments, the lens and
filter must be cleaned more often. Periodically the filter should be replaced
and the projector should be cleaned internally. As long as the projector is
properly maintained in this manner, use in these environments will not reduce
the overall operation life. Please note that all internal cleaning must be
performed by an Authorized Sharp Industrial LCD Products Dealer or Service
Center.
41˚F
(
ם 5˚C) Notes on Operation
• The exhaust vent, the lamp cage cover and adjacent areas may be
extremely hot during projector operation. To prevent injury, do not touch
these areas until they have sufficiently cooled.
• Allow at least 4 inches (10 cm) of space between the cooling fan (exhaust
vent) and the nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection device will automatically
turn off the projector lamp. This does not indicate a malfunction. Remove
the projector power cord from the wall outlet and wait at least 10 minutes.
Then turn on the power by plugging the power cord back in. This will return
the projector to the normal operating condition.
Temperature Monitor Function
If the projector starts to overheat due to setup problems or a dirty air filter,
“TEMP.” and “ ” will flash in the lower-left corner of the picture. If the
temperature continues to rise, the lamp will turn off, the TEMPERATURE
WARNING indicator on the projector will flash, and after a 90-second cooling-
off period the power will shut off. Refer to “Lamp/Maintenance Indicators” on
page 47, for details.
• The cooling fan regulates the internal temperature, and its performance is
automatically controlled. The sound of the fan may change during projector operation
due to changes in the fan speed.
Lamp Monitor Function
When the projector is turned on after the lamp has been used for 1,400 hours,
“LAMP” and “ ” will flash in the lower-left corner of the picture to advise you
to replace the lamp. See pages 48 and 49 for lamp replacement. If the lamp
has been used for 1,500 hours, the projector power will automatically turn off
and the projector will enter standby mode. Refer to “Lamp/Maintenance
Indicators” on page 47, for details.
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Access the PDF Operation Manuals (for Windows and Macintosh)
PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to
install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet,
To Install Acrobat Reader from the CD-ROM
For Windows:
1 Insert the CD-ROM in the CD-ROM drive.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “My Computer” icon.
3 Double click on the “CD-ROM” drive.
4 Double click on the “manuals” folder.
5 Double click on the “acrobat” folder.
6 Double click on the “windows” folder.
2 Double click on the “CD-ROM” icon.
3 Double click on the “manuals” folder.
4 Double click on the “acrobat” folder.
5 Double click on the “mac” folder.
6 Double click on the desired installation program
and follow the instructions on the screen.
7 Double click on the desired installation program
and follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the appropriate
version from the Internet.
Accessing the PDF Manuals
For Windows:
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive.
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click on the “My Computer” icon.
3 Double click on the “CD-ROM” drive.
4 Double click on the “manuals” folder.
5 Double click on the “pg-c30xu” folder.
2 Double click on the “CD-ROM” icon.
3 Double click on the “manuals” folder.
4 Double click on the “pg-c30xu” folder.
5 Double click on the language (name of the folder)
that you want to view.
6 Double click on the language (name of the folder)
that you want to view.
6 Double click on the “c30” pdf file to access the
projector manuals.
7 Double click on the “c30” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
7 Double click on the pdf file.
8 Double click on the pdf file.
• If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file
using the “File”, “Open” menu.
• See the “readme.txt” file on the CD-ROM for important information on the CD-ROM not included in this operation manual.
For SHARP Assistance (U.S.A. only)
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on page 49. If this operation manual does not answer your question, please call toll free 1-888-GO-SHARP
(1-888-467-4277) for further assistance. Or, send us an e-mail at lcdsupport@sharplcd.com .
E-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Projector
LAMP REPLACEMENT
MUTE button
17
47
indicator
TEMPERATURE WARNING
indicator
POWER indicator
16
16
47
17
VOLUME buttons (
ם /מ ) POWER buttons (ON/OFF)
MENU button
KEYSTONE button
INPUT button
20
17
33
34
37
23
23
32
36
35
20
23
AUTO SYNC button
RESIZE button
GAMMA button
UNDO button
FREEZE button
ENLARGE button
BLACK SCREEN button
ADJUSTMENT buttons
ENTER button
(∂/ƒ/ß / ©)
Zoom knob
17
21
17
Carrying handle
50
49
19
Remote control sensor
Kensington Security Standard
connector
Focus knob
Foot release
Front and Top View
Speaker
Side and Rear View
Air filter/Cooling fan (Intake vent)
46
21
Cooling fan (Exhaust vent)
5
Remote control sensor
INPUT 2 port (HD 15)
INPUT 1 port (HD 15)
11
14
11
13
AUDIO OUTPUT terminal
(3.5 mm stereo minijack)
RS-232C port (9-pin Mini DIN)
AUDIO INPUT terminal
OUTPUT port for INPUT 1, 2 (HD 15)
11 for INPUT 1, 2
(3.5 mm stereo minijack)
S-VIDEO INPUT terminal
(4-pin Mini DIN)
AUDIO INPUT 3 terminals (RCA)
AC socket
12
11
12
12
VIDEO INPUT 3 terminal
(RCA)
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
Remote Control
Front View
Rear View
MUTE button
17
POWER buttons
VOLUME buttons
(
ם /מ ) 16
17
(ON/OFF)
LEFT-CLICK
button
22
20
37
22
23
KEYSTONE/BLACK
SCREEN button
LASER POINTER/
MENU button
MOUSE/
ADJUSTMENT
buttons (∂/ƒ/ß/©)
22
23
22
23
RIGHT-CLICK/
ENTER button
UNDO button
INPUT button
FREEZE button
ENLARGE button
TOOLS button
17
33
34
43
21
20
32
36
35
22
AUTO SYNC button
RESIZE button
GAMMA button
BACKLIGHT button
MOUSE/
ADJUSTMENT
switch
Top View
Remote control
signal transmitter
Laser
pointer
window
5
Inserting the batteries
Press in on the arrow
Insert two AA size
Insert the side tabs of
the battery cover into
their slots and press the
cover in until it is
1
2
3
mark and slide in the
batteries, making sure
their polarities match the
and marks inside the battery compartment.
direction of the arrow to
remove the battery cover.
properly seated.
Battery
cover
Battery
cover
Battery
compartment
E-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup & Connections
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied Accessories
Remote control
RRMCG1579CESA
Power cord
QACCU5013CEZZ
Two AA size batteries
Computer audio cable
QCNW-4870CEZZ
DIN-D-sub RS-232C cable
QCNW-5288CEZZ
Computer RGB cable
QCNW-5304CEZZ
Remote mouse receiver
RUNTK0673CEZZ
USB mouse control cable
QCNW-5680CEZZ
PS/2 mouse control cable
QCNW-5113CEZZ
Extra air filter
PFILD0076CEZZ
Lens cap
PCAPH1307CESB
CD-ROM
UDSKA0019CEN1
LCD projector quick reference
TINS-7025CEZZ
LCD projector operation manual
TINS-7023CEZZ
Sharp Advanced Presentation Software
operation manual
TINS-7054CEZZ
E-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Power cord
QACCU5013CEZZ
Connecting the Projector to a Computer
You can connect your projector to a computer for projection of full color computer images.
To a computer using the standard 15-pin input
Computer RGB cable
QCNW-5304CEZZ
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the supplied computer RGB cable
to the INPUT 1 or 2 port on the projector.
2 Connect the other end to the Monitor output port on the
computer. Secure the connectors by tightening the
thumb screws.
3 To use the built-in audio system, connect one end of
the supplied computer audio cable to the AUDIO INPUT
terminal for INPUT 1, 2 on the projector.
4 Connect the other end to the Audio output terminal on
the computer.
CAUTION
• Before connecting, be sure to turn both the projector and the
computer off. After making all connections, turn the projector
on first. The computer should always be turned on last.
• Please read the computer’s operation manual carefully.
• Refer to page 55 “Computer Compatibility Chart” for a list of
computer signals compatible with the projector. Use with
computer signals other than those listed may cause some of
the functions not to work.
When connecting this projector to a computer, select
“Computer/RGB” for “Signal Type” on the GUI menu. (See
page 27.)
• A Macintosh adaptor may be required for use with some
Macintosh computers. Contact your nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center.
E-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting other compatible computers
When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.
When connecting this projector to a computer, select “Computer/RGB” for “Signal Type” on the GUI menu. (See page 27.)
• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
• AUDIO INPUT for INPUT 1, 2 can be used input audio corresponding to the INPUT 1 and 2 video.
“Plug and Play” function
• This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible
computer will communicate their setting requirements, allowing for quick and easy setup.
• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.
• The DDC, Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible
computer.
Connecting the Projector to Video Equipment
You can connect your projector to a VCR, laser disc player, DVD player, DTV decoder and other audiovisual
equipment.
CAUTION
• Always turn off the projector while connecting to video equipment, in order to protect both the projector and the equipment
being connected.
To a video source (VCR, laser disc player, DTV decoder or DVD player) using the standard video input
1 Connect the yellow RCA connectors to the corresponding
yellow VIDEO INPUT 3 terminal on the projector and the Video
output terminal on the video source.
2 To use the built-in audio system, connect the red and white
RCA connectors to the corresponding red and white AUDIO
INPUT 3 terminals on the projector and the Audio output
terminals on the video source.
The S-VIDEO INPUT terminal uses a video signal system in which
the picture is separated into a color and a luminance signal to
realize a higher-quality image.
When cables are connected to both the S-VIDEO INPUT and
VIDEO INPUT 3 terminals, images input through the S-VIDEO
INPUT terminal have priority over images input through the VIDEO
INPUT 3 terminal.
• For higher quality video, you may use the S-VIDEO INPUT
terminal on the projector. S-video cable is sold separately.
• If your video equipment does not have an S-video output
terminal, use the Composite video output terminal.
2Audio cable (sold separately)
To audio output terminals
1Video cable (sold separately)
To video output terminal
S-video cable (sold separately)
To S-video output terminal
VCR
or
Laser disc player
E-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
To a DTV decoder or DVD player
1 Connect one end of the HD-15-RGB cable to the INPUT 1 or
2 port on the projector.
2 Connect the other end to the corresponding terminals on the
video source.
3 To use the built-in audio system, connect one end of the audio
cable (sold separately) to AUDIO INPUT terminal for INPUT
1, 2 on the projector.
Connect the other end to the Audio output terminal on the
video source.
Select “Computer/RGB” or “Component” for “Signal Type” on
the GUI menu, depending on the video source.
HD-15-RGB cable (sold separately)
2To video input terminals
DTV decoder
or
DVD player
Audio cable (sold separately)
To audio output terminals
Connecting an amplifier and other audio components
CAUTION
• Always turn off the projector while connecting to audio
components, in order to protect both the projector and the
components being connected.
• By using external audio components, the volume can be
amplified for better sound.
• The AUDIO OUTPUT terminal allows you to output audio to audio
components from the selected AUDIO INPUT terminal for INPUT
1, 2 or AUDIO INPUT 3 terminals connected to audiovisual
equipment.
Audio cable (sold separately)
To audio input terminals
Amplifier
E-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting RS-232C Port
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross
type, sold separately), the computer can be used to control the projector and check the status of the projector.
See pages 52 and 53 for details.
Computer RGB cable
QCNW-5304CEZZ
DIN-D-sub RS-232C
cable
QCNW-5288CEZZ
Computer audio cable
QCNW-4870CEZZ
1 Connect the supplied DIN-D-sub RS-232C cable to the RS-232C port on the projector.
2 Connect an RS-232C cable (null modem, cross type, sold separately) to the other end of DIN-D-sub RS-
232C cable and to the serial port on the computer.
2RS-232C cable
(null modem, cross type, sold separately)
1 DIN-D-sub
RS-232C cable
CAUTION
• Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer.
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set up. Please refer to the
operation manual of the computer for details on setting up/installing the correct mouse driver.
• The arrows (→, ↔) indicate the direction of the signals.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center.
E-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector
Connecting the Remote Mouse Receiver
You can use the remote control as a remote mouse.
Connecting to the USB port on a PC or Macintosh
1 Connect one end of the supplied USB mouse control cable to the corresponding terminal on the computer.
2 Connect the other end to the USB port on the remote mouse receiver.
USB mouse control
cable
QCNW-5680CEZZ
Remote mouse
receiver
RUNTK0673CEZZ
Use the USB port (PC
or Macintosh) to
connect the supplied
USB mouse control
cable to the remote
mouse receiver.
USB port
Connecting to the PS/2 port on a PC
1 Turn off the power of the PC.
2 Connect one end of the supplied PS/2 mouse control cable to the corresponding terminal on the PC.
3 Connect the other end to the PS/2 port on the remote mouse receiver.
4 Turn on the power of the PC.
PS/2 mouse control
cable
QCNW-5113CEZZ
Remote mouse
receiver
RUNTK0673CEZZ
Use the PS/2 port
(PC) to connect the
supplied PS/2 mouse
control cable to the
PS/2 port
remote mouse
receiver.
CAUTION
• Do not connect or disconnect the mouse control cables to or from the computer while it is on. This may damage your
computer.
• Do not connect both the PS/2 and USB mouse control cables to the remote mouse receiver.
• The wireless mouse functions can be used to operate computers compatible with PS/2 or USB type mouse systems.
E-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Basic Operations
1 Make the necessary connections before pro-
ceeding. Connect the power cord to a wall outlet.
The POWER indicator lights up red and the
projector enters standby mode.
• If the bottom filter cover is not securely installed, the
POWER indicator flashes.
2 Press Power ON.
2
• The flashing green LAMP REPLACEMENT indicator shows
that the lamp is warming up. Wait until the indicator stops
flashing before operating the projector.
• If the power is turned off and then immediately turned on
again, it may take a short while before the lamp turns on.
• If the keylock level is set to “Level A” or “Level B”, Power
ON and Power OFF can only be used on the remote
control. (See page 41.)
• After the projector is unpacked and turned on for the first
time, a slight odor may be emitted from the exhaust vent.
This odor will soon disappear with use.
When the power is on, the LAMP REPLACEMENT
indicator lights indicating the status of the lamp.
Green: Lamp is ready.
Flashing green: Warming up.
Red: Change the lamp.
E-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
3 Rotate the zoom ring. The image can be adjusted
to the desired size within the zoom range.
4
3
4 Rotate the focus ring until the image on the screen
becomes clear.
6
7
8
5
5 Press INPUT to select the desired input mode.
EXAMPLE
Press INPUT again to change the mode.
INPUT 1 Mode
INPUT 2 Mode
5
• When no signal is being received, “NO SIGNAL” will be
displayed. When a signal that the projector is not preset
to receive is being received, “NOT REG.” will be displayed.
f
f
6 Press VOLUME
/ to adjust the volume. 7 Press MUTE to temporarily turn off the sound.
Press MUTE again to turn the sound back on.
8 Press POWER OFF.
Press POWER OFF again while the message is
displayed.
INPUT 3 (VIDEO)
Mode
• If you accidentally pressed POWER OFF and do not want
to turn off the power, wait until the power off screen
disappears.
• When POWER OFF is pressed twice, the POWER indicator
will light up red and the cooling fan will run for about 90
seconds. The projector will then enter standby mode.
• Wait until the cooling fan stops before disconnecting the
power cord.
• The power can be turned on again by pressing POWER
ON. When the power is turned on, the POWER indicator
and the LAMP REPLACEMENT indicator light green.
• The POWER indicator flashes if the bottom filter cover is
not securely installed.
6
7
8
E-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Move the projector forward or backward if the edges of the image are distorted.
• The projector lens should be centered in the middle of the screen. If the lens center is not perpendicular to the screen, the image will be
distorted, making viewing difficult.
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes out colors, making viewing
difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
• A polarizing screen cannot be used with this projector.
X
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according
to the desired picture size (see the table below).
L
H
Picture size
NORMAL Mode
(4:3)
Projection distance (L)
Distance from the lens center to the
bottom of the image (H)
Diag.
300Љ
200Љ
150Љ
100Љ
84Љ
72Љ
60Љ
40Љ
Width
240Љ
160Љ
120Љ
80Љ
67Љ
58Љ
48Љ
32Љ
Height
180Љ
120Љ
90Љ
60Љ
50Љ
43Љ
36Љ
24Љ
Maximum
Minimum
46Ј (14.0 m)
30Ј 7Љ (9.3 m)
23Ј 1Љ (7.0 m)
15Ј 6Љ (4.7 m)
13Љ (4.0 m)
11Ј 1Љ (3.4 m)
9Ј 3Љ (2.8 m)
6Ј 1Љ (1.9 m)
35Ј 4Љ (10.8 m)
23Ј 6Љ (7.2 m)
17Ј 8Љ (5.4 m)
11Ј11Љ (3.6 m)
9Ј 11Љ (3.0 m)
8Ј 6Љ (2.6 m)
7Ј 1Љ (2.2 m)
4Ј 8Љ (1.4 m)
17 29⁄32Љ (45.5 cm)
11 29⁄32Љ (30.2 cm)
9Љ (22.8 cm)
6 3⁄32Љ (15.5 cm)
5 3⁄32Љ (13.0 cm)
4 13⁄32Љ (11.2 cm)
3 45⁄64Љ (9.4 cm)
2 13⁄32Љ (6.1 cm)
The formula for picture size and projection distance
y = 0.1533x
ם 0.1057 y1 = 0.118x
ם 0.0048 y23 = 0.0592x
ם 0.1134 x: Picture size (diag.) (inches)
y : Maximum projection distance (feet)
y1 : Minimum projection distance (feet)
y32 : Distance from the lens center to the
bottom of the image (H) (inches)
• There is an error of
ע 3% in the formula above. Picture size
Projection distance (L)
WIDE Mode
(16:9)
Distance from the lens center to the
bottom of the image (H)
Diag.
300Љ
200Љ
150Љ
133Љ
106Љ
100Љ
92Љ
84Љ
72Љ
60Љ
40Љ
Width
261Љ
174Љ
131Љ
116Љ
92Љ
87Љ
80Љ
73Љ
63Љ
Height
147Љ
98Љ
74Љ
65Љ
52Љ
49Љ
45Љ
41Љ
Maximum
49Ј 6Љ (15.1 m)
33Ј (10.1 m)
24Ј 10Љ (7.6 m)
22Ј (6.7 m)
Minimum
38Ј (11.6 m)
25Ј 4Љ (7.7 m)
19Ј (5.8 m)
16Ј 10Љ (5.1 m)
13Ј 5Љ (4.1 m)
12Ј 10Љ (3.9 m)
11Ј 8Љ (3.6 m)
10Ј 9Љ (3.3 m)
9Ј 2Љ (2.8 m)
7Ј 7Љ (2.3 m)
5Ј (1.5 m)
מ 5Љ (מ 12.7 cm) מ 3 11⁄32Љ (מ 8.5 cm) מ 2 33⁄64Љ (מ 6.4 cm) מ 2 15⁄64Љ (מ 5.7 cm) מ 1 25⁄32Љ (מ 4.5 cm) מ 1 43⁄64Љ (מ 4.3 cm) מ 1 35⁄64Љ (מ 3.9 cm) מ 1 13⁄32Љ (מ 3.6 cm) מ 1 7⁄32Љ (מ 3.1 cm) מ 1 1⁄64Љ (מ 2.6 cm) מ 11⁄16Љ (מ 1.7 cm) 17Ј 7Љ (5.4 m)
16Ј 9Љ (5.1 m)
15Ј 3Љ (4.6 m)
14Ј (4.3 m)
35Љ
29Љ
20Љ
12Ј (3.7 m)
52Љ
35Љ
9Ј 11Љ (3.0 m)
6Ј 7Љ (2.0 m)
The formula for picture size and projection distance
y = 0.1647x
ם 0.1020 y1 = 0.1266x
ם 0.0312 y23 =
מ 0.0166x מ 0.0188 x: Picture size (diag.) (inches)
y : Maximum projection distance (feet)
y1 : Minimum projection distance (feet)
y23 : Distance from the lens center to the
bottom of the image (H) (inches)
• There is an error of
ע 3% in the formula above. • Values with a minus (
מ ) sign indicate the distance of the lens center below the bottom of the screen. E-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Using the Adjustment Foot
You can adjust the height of the image by raising the
projector with the foot release.
1
3
1 Press the foot release and lift the projector to the
desired angle. (Adjustable up to approximately
5° from the standard position.)
2 Remove your hand from the foot release. Once
the adjustment foot has locked in position, release
the projector.
Foot release
3 If the screen is at an angle, the adjuster can be
used to adjust the angle of the image. (Adjustable
up to approximately 1° from the original position.)
Returning the projector to its original position
While holding the projector, press the foot release and slowly lower the projector to its original position.
• When an adjustment is made, the image may become distorted (keystoned), depending on the relative positions of the projector and the
screen.
CAUTION
• Do not press the foot release when the adjustment foot is extended without firmly holding the projector.
• Do not hold the lens when lifting or lowering the projector.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the
projector.
Reversed Image Setup
Rear projection
Projection using a mirror
• Place a translucent screen between the projector and
the audience.
• When the distance between the projector and screen
is not sufficient for normal rear projection, you can
use a mirror to reflect the image onto the screen.
• Place a mirror (normal flat type) in front of the lens.
• Project the normal image onto the mirror.
• The image reflected from the mirror is projected onto
the translucent screen.
• Use the projector’s menu system to reverse the
projected image. (See page 42 for use of this
function.)
• Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and level.
CAUTION
• When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount Setup
• It is recommended that you use the optional Sharp ceiling-
mount bracket for this installation.
• Before mounting the projector, contact your nearest Authorized
Sharp Industrial LCD Products Dealer or Service Center to
obtain the recommended ceiling-mount bracket (sold
separately). (AN-XGCM51 ceiling-mount bracket, AN-
EP101AP extension tube for AN-XGCM51.)
• When the projector is in the inverted position, use the upper
edge of the screen as the base line.
• Use the projector’s menu system to select the appropriate
projection mode. (See page 42 for use of this function.)
E-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Screen
Projector
Remote control
Digital Image Adjustments
Digital Keystone Correction
When the image is distorted due to the projection angle,
the Digital Keystone Correction function allows you to
correct it.
1, 4a
3
(Slide the MOUSE/ADJUSTMENT switch
MOUSE
ADJ.
on the remote control to the ADJ. position.)
2
1
Press KEYSTONE to select mode. Each time
KEYSTONE is pressed, the screen changes as
shown on the left.
4b
On-screen Display
(Example:
4:3 NORMAL image)
On-screen Display
(Example:
2
3
4
Press ENTER to display test pattern.
16:9 WIDE image)
Press ∂/ƒ/ß/© to make adjustments.
a. Press KEYSTONE until normal screen
appears.
b. To reset the KEYSTONE setting, press UNDO.
• Straight lines and the edges of the displayed image may
appear jagged, when adjusting the KEYSTONE setting.
Digital Shift
When a WIDE or NORMAL (WIDE) image is projected,
this function can be used to shift the image up or down.
2Test Pattern
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1
Press KEYSTONE to select “DIGITAL SHIFT” as
shown on the near left.
2
3
4
Press ENTER to display test pattern.
Digital Keystone Correction
Press ∂/ƒ/ß/© to make adjustments.
Pressing ∂
Pressing ƒ
in Step 2
a. Press KEYSTONE until normal screen
in Step 2
appears.
b. To reset the DIGITAL SHIFT setting, press
UNDO.
• This function only works with WIDE and NORMAL (WIDE)
picture display modes during video or DTV input. (See page
36 for details.) The DIGITAL SHIFT screen is not displayed
when projecting images other than WIDE or NORMAL
(WIDE).
Digital Shift
or
Press ∂.
Press ƒ.
E-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Wireless Mouse from the Remote Control
Using the Remote Control as a Wireless Mouse
The remote control has the following three functions:
• Projector control
MOUSE/ADJUSTMENT switch
(Remote control)
• Wireless mouse
• Laser pointer
MOUSE
ADJ.
MOUSE
ADJ.
Wireless mouse
Laser pointer
Projector control
Remote Control/Mouse Receiver Positioning
• The remote control can be used to control the projector within the ranges shown below.
• The remote mouse receiver can be used with the remote control to control the mouse functions of a connected
computer within the ranges shown below.
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.
Controlling the Projector
Using the Wireless Mouse
Remote control
Remote control
23Ј (7 m)
30˚
30˚
45˚
30˚
30˚
120˚
13Ј(4 m)
Remote
45˚
mouse
receiver
30˚
Remote control
E-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Wireless Mouse from the Remote Control
Effective buttons in MOUSE mode
Use as a Wireless Mouse
Be sure the supplied remote mouse receiver is
connected to your computer.
Remote control
(Front view)
(Slide the MOUSE/ADJUSTMENT switch on
MOUSE
ADJ.
LASER POINTER
BLACK SCREEN
MOUSE
the remote control to the MOUSE position.)
• The wireless mouse may not operate correctly if your
computer serial port is not correctly set up. Refer to the
computer’s operation manual for details of setting up/
installing the mouse driver.
• For one-button mouse systems, use either the LEFT-CLICK
or RIGHT-CLICK button.
RIGHT-CLICK
Using the remote control in a dark room
Press BACKLIGHT, and the buttons will light up. Green
lights refer to mouse operations, and red lights to
projector adjustments.
BACKLIGHT
LEFT-CLICK
Button name
Position of MOUSE/ADJUSTMENT switch
MOUSE ADJ.
LASER POINTER/MENU LASER POINTER (GREEN) MENU (RED)
Remote control
(Rear view)
BLACK SCREEN/KEYSTONE BLACK SCREEN (GREEN)
RIGHT-CLICK/ENTER
RIGHT-CLICK (GREEN)
MOUSE/ADJUSTMENT MOUSE (NOT LIT)
KEYSTONE (RED)
ENTER (RED)
ADJUSTMENT (NOT LIT)
—
LEFT-CLICK
POWER ON/OFF
VOLUME
ם /מ MUTE
ON (NOT LIT)
INPUT
UNDO
FREEZE
ON (RED)
AUTO SYNC
ENLARGE
RESIZE
TOOLS
GAMMA
Use as a Laser Pointer
(Slide the MOUSE/ADJUSTMENT switch on
the remote control to the MOUSE position.)
MOUSE
ADJ.
Press LASER POINTER ( ) to activate the laser
pointer. When the button is released, the light
automatically goes off.
• For safety, the laser pointer automatically goes off after 1
minute of continuous use. To turn it on, release LASER
POINTER ( ) and press again.
E-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the GUI (Graphical User Interface) Menu Screens
Projector
Remote control
This projector has two sets of menu screens (INPUT 1
or 2 and INPUT 3) that allow you to adjust the image
and various projector settings. These menu screens can
be operated from the projector or the remote control
with the following buttons.
1, 7
2, 3, 5
4
6
(GUI) On-screen Display
INPUT 1 or 2 (COMPUTER/RGB) mode
INPUT 3 (VIDEO) mode
1
1
ß 2©
ß 2©
∂
∂
3
ƒ
3
ƒ
ß 5©
ß 5©
4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
ß 2©
1 Press MENU to display the INPUT 1, 2 or 3 mode
menu bar.
2 Press ß/© to select an adjustment menu on the
menu bar.
ß 5©
3 Press ∂/ƒ to select a specific adjustment item.
4 To display a single adjustment item, press ENTER
after selecting the item. Only the menu bar and
the selected adjustment item will appear.
5 Press ß/© to adjust the item.
6 Press UNDO to return to the previous screen.
7 Press MENU to exit from the GUI.
• For details on items on the menu screen, see the tree charts
on the next page.
E-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the GUI (Graphical User Interface) Menu Screens
Items on the INPUT 1 or INPUT 2 Mode Menu Bar
Main menu
Items on the INPUT 3 (VIDEO) Mode Menu Bar
Main menu
Picture
Contrast
Bright
Color
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 3 ם 3 Picture
Contrast
Bright
Color
מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 30 ם 30 מ 3 ם 3 Tint
Tint
Red
Sharp
Red
Computer/RGB
Component
Blue
CLR Temp
Reset
Blue
Interlaced
CLR Temp
Reset
Signal Type
Progressive
Interlaced
I/P Conversion
I/P Conversion
Resolution
800
ן 600 640
ן 480 Vert Freq
75 Hz
72 Hz
Progressive
1
Fine Sync
Clock
מ 150 ם 150 Treble
מ 30 ם 30 מ 30 ם 30 Audio
2
•
Bass
Phase
מ 60 ם 60 מ 150 ם 150 מ 60 ם 60 •
7
Reset
H-Pos
V-Pos
Options
Lamp Timer
Auto
Resolution
800
ן 600 640
ן 480 Vert Freq
75 Hz
72 Hz
1
Reset
BLK SCRN Disp [ON/OFF]
PAL (50/60Hz)
SECAM
2
•
Save Setting
OSD Display
Video System
Background
[ON/OFF]
•
NTSC4.43
NTSC3.58
Select Setting
Special Modes
Signal Info
7
1024
ן 864 1152
ן 864 1152
ן 870 1152
ן 882 Startup Image
Economy Mode
Sharp
Custom
Blue
Auto Sync
[ON/OFF]
[ON/OFF]
Auto Power Off [ON/OFF]
Keylock Level
Password
English
Auto Sync Disp
Treble
מ 30 ם 30 Audio
None
Resolution 640
ן 480 Bass
מ 30 ם 30 Hor Freq
Vert Freq
37.5 kHz
72 Hz
Sharp
Custom
None
Language
Reset
Deutsch
Options
Lamp Timer
Sharp
Custom
Blue
Español
BLK SCRN Disp [ON/OFF]
Normal
Level A
Level B
Nederlands
Français
OSD Display
Background
[ON/OFF]
None
Italiano
Startup Image
Economy Mode
Sharp
Custom
None
Svenska
Old Password
New Password
Reconfirm
Português
Auto Power Off [ON/OFF]
Keylock Level
Password
English
Normal
Level A
Level B
Language
Front
Deutsch
PRJ Mode
Old Password
New Password
Reconfirm
Ceiling
ם Front Rear
Español
Nederlands
Français
Ceiling
ם Rear Status
Italiano
Svenska
Português
• The resolution, vertical frequency and horizontal frequency figures displayed above
are for example purposes only.
• “Color” and “Tint” appear only when Component input is selected in INPUT 1 or 2
mode.
Front
PRJ Mode
• Only the items highlighted in the tree charts above can be adjusted.
• To adjust the items under the sub menu, press © after selecting the sub menu.
Ceiling
ם Front Rear
Ceiling
ם Rear Status
E-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the On-screen Display Language
Projector
Remote control
English is the preset language for the On-screen
Display. The language can be set to English, German,
Spanish, Dutch, French, Italian, Swedish, Portuguese,
Chinese, Korean or Japanese.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 5
2, 3
1 Press MENU.
2 Press ß/© to select “Language”.
4
3 Press ∂/ƒ to select the desired language .
4 Press ENTER to save the setting. The On-screen
Display is now programed to display in the
language selected.
(GUI) On-screen Display
5 To exit from the GUI, press MENU.
Selecting the Video Input System Mode (INPUT 3 (VIDEO) mode only)
Projector
Remote control
The video input system mode is preset to “Auto”;
however, it can be changed to a specific system mode,
if the selected system mode is not compatible with the
connected audiovisual equipment.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
2, 3, 4
1 Press MENU.
2 Press ß/© to select “Options”.
5
3 Press ∂/ƒ to select “Video System”, and then
press ©.
4 Press ∂/ƒ to select the desired video system
(GUI) On-screen Display
mode.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• When the system mode is set to “Auto”, you may not receive
a clear picture due to signal differences. Should this occur,
switch to the video system of the source signal.
E-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
Projector
Remote control
Adjusting the Picture
You can adjust the projector’s picture to your prefer-
ences with the following picture settings.
Description of Adjustment Items
ß button
© button
1, 4
Selected item
Contrast
Bright
Color
Tint
For less contrast
For less brightness
For less color intensity
Skin tones become purplish Skin tones become greenish
For more contrast
For more brightness
For more color intensity
2, 3
Sharp
For less sharpness
For more sharpness
Red
For weaker red
For stronger red
Blue
Reset
For weaker blue
All image adjustment items are returned to the factory preset
settings.
For stronger blue
(GUI) On-screen Display
(COMPUTER/RGB input in INPUT 1 or 2 mode)
• “Color”, “Tint” and “Sharp” do not appear for COMPUTER/
RGB input in INPUT 1 or 2 mode.
1
• “Sharp” do not appear for COMPONENT input in INPUT 1
or 2 mode.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2
2 Press ∂/ƒ to select a specific adjustment item.
3 Press ß/© to move the mark of the selected
adjustment item to the desired setting.
4 To exit from the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Picture”
menu screen and press ENTER.
• The adjustments can be stored separately in the “INPUT
1”, “INPUT 2” and “INPUT 3 (VIDEO)” modes.
E-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
Projector
Remote control
Adjusting the Color Temperature
This function can be used to adjust the color
temperature to suit the type of image input to the
projector (video, computer image, TV broadcast, etc.).
Decrease the color temperature to create warmer,
reddish images for natural flesh tones. Increase the color
temperature to create cooler, bluish images for a brighter
picture.
1, 4
2, 3
Description of Color Temperature
מ 3 ם 3 (Red) ß button
© button (Blue)
Decreases color temperature for Increases color temperature for
warmer, reddish,
incandescent-lighting-like
images.
cooler, bluish, florescent-
lighting-like images.
(High color temperature)
(GUI) On-screen Display
(Low color temperature)
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press ∂/ƒ to select “CLR Temp”.
3 Press ß/© to move the mark of the selected
adjustment item to the desired setting.
4 To exit from the GUI, press MENU.
Selecting the Signal Type
This function allows you to select the input signal type
(COMPUTER/RGB or COMPONENT) for INPUT 1 or 2
port.
Projector
Remote control
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
2, 3, 4
1 Press MENU.
5
2 Press ß/© to select “Picture”.
3 Press ∂/ƒ to select “Signal Type”, and then
press ©.
(GUI) On-screen Display
4 Press ∂/ƒ to select “Computer/RGB” or
“Component”.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
E-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustments
Projector
Remote control
I/P Conversion
This function allows you to select either an interlaced
display or a progressive display of a video signal. The
progressive display projects a smoother video image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 6
2, 3, 4
1 Press MENU.
2 Press ß/© to select “Picture”.
3 Press ∂/ƒ to select “I/P Conversion”, and then
press ©.
5
4 Press ∂/ƒ to select “Interlaced” or “Progressive”.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
(GUI) On-screen Display
Interlaced mode
Interlaced mode creates a single image through the activation
of scanning lines in two fields. Use this mode when projecting
moving images.
Progressive mode
Progressive mode creates a single image using all available
scanning lines. Use this mode when projecting still images to
avoid flicker and stripes that result from interlaced source still
images.
Audio Adjustments
Projector
Remote control
This projector’s audio is factory preset to standard
settings. However, you can adjust it to suit your own
preferences by adjusting the following audio settings.
Description of Adjustment Items
Selected item
ß button
© button
1, 5
Treble
Bass
Reset
For weaker treble
For weaker bass
All audio adjustment items are returned to the factory preset
settings.
For stronger treble
For stronger bass
2, 3, 4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
2
3
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press ß/© to select “Audio”.
3 Press ∂/ƒ to select a specific adjustment item.
4 Press ß/© to move the mark of the selected
adjustment item to the desired setting.
5 To exit from the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Audio”
menu screen and press ENTER.
E-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments (INPUT 1 or 2 mode Only)
Projector
Remote control
Adjusting the Computer Image
When displaying computer patterns which are very
detailed (tiling, vertical stripes, etc.), interference may
occur between the LCD pixels, causing flickering,
vertical stripes, or contrast irregularities in portions of
the screen. Should this occur, adjust “Clock”, “Phase”,
“H-Pos” and “V-Pos” for the optimum computer image.
1, 5
Description of Adjustment Items
2, 3, 4
Selected item
Description
Clock
Phase
H-Pos
V-Pos
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
• Computer image adjustments can be made easily by
pressing AUTO SYNC ( ). See page 32 for details.
(GUI) On-screen Display
(Select the desired computer input mode with INPUT.)
2
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU. Menu bar and “Picture” menu
screen appear. GUI operation guide is also
displayed.
2 Press ß/© to select “Fine Sync”.
3
3 Press ∂/ƒ to select a specific adjustment item.
4 Press ß/© to move the mark of the selected
adjustment item to the desired setting.
5 To exit from the GUI, press MENU.
• To reset all adjustment items, select “Reset” on the “Fine
Sync” menu screen and press ENTER.
E-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments (INPUT 1 or 2 mode Only)
Projector
Remote control
Saving and Selecting Adjustment Settings
This projector allows you to store up to seven adjustment
settings for use with various computers. Once these
settings are stored, they can be easily selected each
time you connect a computer to the projector.
1, 6
Saving the adjustment setting
2, 3, 4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
5
1 Press MENU.
2 Press ß/© to select “Fine Sync”.
(GUI) On-screen Display
2
3 Press ∂/ƒ to select “Save Setting”, and then press
©.
4 Press ∂/ƒ to select the desired memory location of
the setting.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
3
Selecting a saved setting
MOUSE
ADJ.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1 Press MENU.
2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Select Setting”, and then press
©.
4
4 Press ∂/ƒ to select the desired memory setting.
5 Press ENTER to select the setting.
6 To exit from the GUI, press MENU.
• If a memory position has not been set, a resolution and
frequency setting will not be displayed.
• When selecting the stored adjustment setting with “Select
Setting”, the computer system should match the stored
setting.
E-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments (INPUT 1 or 2 mode Only)
Projector
Remote control
Special Mode Adjustment
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected.
However, for some signals, the optimal resolution mode
in “Special Modes” on the “Fine Sync” menu screen
may need to be selected to match the computer display
mode.
1, 6
2, 3, 4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
5
1 Press MENU.
2 Press ß/© to select “Fine Sync”.
(GUI) On-screen Display
3 Press ∂/ƒ to select “Special Modes”, and then
press ©.
4 Press ∂/ƒ to select the optimal resolution mode.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• Avoid displaying computer patterns which repeat every
other line (horizontal stripes). (Flickering may occur, making
the image hard to see.)
• When inputting DTV 480P signals, select “480P” in step 4
above.
Projector
Remote control
Checking the Input Signal
This function allows you to check the current input signal
information.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 4
1 Press MENU.
2, 3
2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Signal Info” to display the
current input signal.
(GUI) On-screen Display
4 To exit from the GUI, press MENU.
E-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Image Adjustments (INPUT 1 or 2 mode Only)
Projector
Remote control
Auto Sync Adjustment
• Used to automatically adjust a computer image.
• Auto Sync adjustment can be made manually by
pressing AUTO SYNC, or automatically by setting
“Auto Sync” to “ON” in the projector’s GUI menu.
1, 5
When “Auto Sync” is set to “ON”:
• The sync adjustment is automatically made each time
the projector is turned on while connected to a com-
puter or the input selection is changed.
2, 3, 4
• The Auto Sync adjustment setting previously made is
cleared when the projector’s setting is changed.
AUTO SYNC
button
(Slide the MOUSE/ADJUSTMENT switch
MOUSE
ADJ.
on the remote control to the ADJ. position.)
1 Press MENU.
(GUI) On-screen Display
2 Press ß/© to select “Fine Sync”.
3 Press ∂/ƒ to select “Auto Sync”.
4 Press ß/© to select “ON”.
5 To exit from the GUI, press MENU.
• Automatic adjustments can be made by pressing AUTO
SYNC.
• When the optimum image cannot be achieved with Auto
Sync adjustment, use manual adjustments. (See page 29.)
On-screen Display
During Auto Sync adjustment, the On-screen Display
changes as shown on the left.
g
• Auto Sync adjustment may take some time to complete,
depending on the image of the computer connected to the
projector.
f
Auto Sync Display Function
s
Normally, an image is not superimposed during Auto
Sync adjustment. You can, however, choose to
superimpose a background image during Auto Sync
adjustment.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
1 Press MENU.
2 Press ß /© to select “Fine Sync”.
3 Press ∂/ƒ to select “Auto Sync Disp”.
4 Press ß/© to select “ ” to superimpose a
background image or “ ” to remove the
background image during Auto Sync adjustment.
5 To exit from the GUI, press MENU.
E-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Useful Features
Freeze Function
Projector
Remote control
This function allows you to instantly freeze a moving
image. This is useful when you want to display a still
image from a computer or video, giving you more time
to explain the image to the audience.
You can also use this function to display a still image
from a computer while you make preparations for the
next computer images to be presented.
1 Press FREEZE to freeze the image.
1, 2
2 Press FREEZE again to return to the moving
image.
On-screen Display
E-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Image Magnification
Projector
Remote control
This function allows you to magnify a specific portion of
an image. This is useful when you want to display a
detailed portion of the image.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ.)
MOUSE
ADJ.
2
1 Press ENLARGE. Each time ENLARGE is
pressed, the image will be magnified.
1
3
2 When the image is magnified, you can pan and
scan around the image by using ∂/ƒ/ß/©.
• Each time ENLARGE is pressed, image magnification
toggles as shown below.
On-screen Display
1 2 3 4 6 8 • If the input signal is changed during digital image
magnification, the image will return to
ן 1. The input signal is changed
(a) when INPUT is pressed,
(b) when the input signal is interrupted, or
(c) when the input resolution and refresh rate changes.
3 To return to
ן 1, press UNDO. E-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Gamma Correction
Projector
Remote control
• Gamma is an image quality enhancement function
that offers a richer image by brightening the darker
portions of the image without altering the brightness
of the brighter portions.
• Four gamma settings are available to allow for
differences in the images displayed and in the
brightness of the room.
• When you are displaying images with frequent, dark
scenes, such as a film or concert, or when you are
displaying images in a bright room, this feature makes
the dark scenes easier to see and gives the impres-
sion of greater depth in the image.
1
2
Gamma Modes
Selected Mode Gamma mode
On-screen Display
STANDARD
GAMMA 1
Standard picture without gamma correction.
STANDARD
GAMMA 1
GAMMA 2
CUSTOM
Brightens darker portions of image for more
enhanced presentations.
GAMMA 2
CUSTOM
Gives greater depth to darker portions of image
for a more exciting theater experience.
Allows you to adjust gamma value using Sharp
Advanced Presentation Software.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press GAMMA. Each time GAMMA is pressed,
the gamma level toggles as shown on the left.
2 To return to the standard image, press UNDO
while “GAMMA” is displayed on the screen.
E-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Picture Display Mode
Projector
Remote control
This function allows you to modify or customize the
picture display mode to enhance the input image.
Depending on the input signal, you can choose
NORMAL, FIT TO SCREEN, DOT BY DOT, WIDE or
NORMAL (WIDE) image.
1 Press RESIZE. Each time RESIZE is pressed, the
picture mode changes as shown below.
1
2 To return to the standard image, press UNDO
while “RESIZE” is displayed on the screen.
2
EXAMPLE
COMPUTER
NORMAL
1024
ן 768 1024
ן 768 1024
ן 768 960
ן 768 FIT TO SCREEN
DOT BY DOT
800
ן 600 1024
ן 768 1600
ן 1200 1280
ן 1024 SVGA (800
ן 600) XGA (1024
ן 768) UXGA (1600
ן 1200) SXGA (1280
ן 1024) –
–
–
4:3 aspect ratio
Other aspect ratios
1024
ן 768 Output screen image
FIT TO SCREEN
Input Signal
NORMAL
DOT BY DOT
4:3 aspect ratio
Other aspect ratios
EXAMPLE
VIDEO/DTV
NORMAL
1024
ן 768 1024
ן 768 WIDE
NORMAL (WIDE)
768
ן 576* 768
ן 576* 768
ן 576* –
4:3
Letterbox
Squeeze
1024
ן 576* 1024
ן 576* 1024
ן 576* 1024
ן 576* 4:3 aspect ratio
480I/P, NTSC, PAL, SECAM
–
–
16:9 aspect ratio, 720P, 1080i
480I/P, 720P, 1080i
*The digital image shift function can be used with these picture display modes.
Output screen image
Input Signal
NORMAL
WIDE
NORMAL (WIDE)
4:3 aspect ratio
480I/P,
NTSC,
PAL,
SECAM
Letterbox
Squeeze
720P,
1080i
16:9 aspect ratio
E-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Screen Function
Projector
Remote control
This function can be used to superimpose a black
screen over the projected image.
BLACK
SCREEN
button
Blacking out the Projected Image
Press BLACK SCREEN. The screen turns black and
“BLACK SCREEN” is displayed on the screen. To return
to the original projected image, press BLACK SCREEN
again.
1, 5
2, 3, 4
MOUSE
ADJ.
• To use the remote control to operate this
function, slide the MOUSE/ADJUSTMENT switch to the
MOUSE position before pressing BLACK SCREEN.
Projected Image
Turning off the On-screen Display
The On-screen Display (“BLACK SCREEN”) that
appears during black screen can be turned off. When
“BLK SCRN Disp” is set to “ ” in the GUI menu, “BLACK
SCREEN” will not be displayed during function.
sg
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
(GUI) On-screen Display
2 Press ß /© to select “Options”.
3 Press ∂/ƒ to select “BLK SCRN Disp”.
4 Press ß/© to select “ ” to turn on or “ ” to turn
off the On-screen Display.
5 To exit from the GUI, press MENU.
On-screen Display Override Function
Projector
Remote control
This function allows you to turn off the on-screen
messages that appear during input select. Once “OSD
Display” is set to “ ” in the GUI menu, the on-screen
messages will not appear when INPUT is pressed.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1, 5
1 Press MENU.
2, 3, 4
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “OSD Display”.
(GUI) On-screen Display
4 Press ß/© to select “ ” to turn on or “ ” to turn
off the On-screen Display.
5 To exit from the GUI, press MENU.
E-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Background Image
This function allows you to select the image displayed
when no signal is being sent to the projector.
Projector
Remote control
Description of Background Images
Selected item
Sharp
Background image
SHARP default image
User customized image (i.e. company logo)
Blue screen
1, 6
Custom
Blue
2, 3, 4
None
Black screen
5
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
1 Press MENU.
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Background”, and then press
©.
4 Press ∂/ƒ to select the background image you want
to display on the screen.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• By selecting “Custom”, the projector can display a custom image
(i.e. your company logo) as the background image. The custom
image must be a 256-color BMP file with a picture size no larger
than 1,024
ן 768 pixels. Please see the Sharp Advanced Presentation Software operation manual for how to save (or change)
a custom image.
Selecting a Startup Image
Projector
Remote control
• This function allows you to specify the image to be
displayed upon the projector’s startup.
• A custom image (i.e. your company logo) can be
uploaded to the projector via an RS-232C cable. See
page 14 in this operation manual, and also the
supplied Sharp Advanced Presentation Software
operation manual for detailed instructions.
1, 6
2, 3, 4
Description of Startup Images
Selected item
Sharp
Startup image
5
SHARP default image
User customized image (i.e. company logo)
Black screen
Custom
None
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
1 Press MENU.
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Startup Image”, and then press
©.
4 Press ∂/ƒ to select the startup image you want to
display on the screen.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• By selecting “Custom”, the projector can display a custom image
(i.e. your company logo) as the startup image. The custom image
must be a 256-color BMP file with a picture size no larger than
1,024
ן 768 pixels. Please see the Sharp Advanced Presentation Software operation manual for how to save (or change) a custom
image.
E-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Economy Mode
These functions allow you to reduce the power
consumption when the projector is in standby mode.
On-screen Display
Automatic Power Shutoff Function
When no input signal is detected for more than 15
minutes, the projector will automatically shut off. The
on-screen message on the left will appear five minutes
before the power is automatically turned off.
Description of Automatic Power Shutoff
Power automatically shuts off after 15 minutes of no
signal input.
Projector
Remote control
Automatic Power Shutoff disabled.
MOUSE
ADJ.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1, 5
1 Press MENU.
2, 3, 4
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Auto Power Off”.
4 Press ß/© to select “ ” or “ ”.
5 To exit from the GUI, press MENU.
(GUI) On-screen Display
• “Auto Power Off” is factory preset to “ ”.
E-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Password
Projector
Remote control
A password can be set by the user and used with the
keylock level to prevent adjustments to certain settings
on the GUI.
Setting the Password
1, 6
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
2, 3,
4, 5
1 Press MENU.
2 Press ß/© to select “Options”.
3 Press ∂/ƒ to select “Password”, and then press
(GUI) On-screen Display
©.
4 Enter the new password using ∂/ƒ to select the
desired number, and then press © to select the
next digit. Continue this procedure for the
remaining three digits, and then press ENTER.
5 Enter the password again (“Reconfirm”) using ∂/
ƒ/ß/©, and then press ENTER.
6 To exit from the GUI, press MENU.
• After setting the password, be sure to write it down in a
secure location so as not to forget it.
(GUI) On-screen Display
Changing the Password
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Follow steps 1 to 3 in “Setting the Password”
above.
2 Enter the old password using ∂/ƒ/ß/©, and then
press ENTER.
3 Enter the new password using ∂/ƒ/ß/©, and
then press ENTER.
4 Enter the password again (“Reconfirm”) using ∂/
ƒ/ß/©, and then press ENTER.
E-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Keylock Level
Projector
Remote control
This function can be used to lock the use of certain
operation buttons on the projector. The user can still
operate the projector fully with the remote control.
Description of Keylock Levels
Selected item
Normal
Description
1, 5
All operation buttons are functional.
Level A
Only INPUT, VOLUME, MUTE, BLACK
SCREEN on the projector are available.
2, 3, 4
Level B
All operation buttons on the projector are
unavailable.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
(GUI) On-screen Display
1 Press MENU.
2 Press ß /© to select “Options”.
3 Press ∂/ƒ to select “Keylock Level”, and then
press ©.
4 Press ∂/ƒ to select the desired level.
5 To exit from the GUI, press MENU.
• To cancel the keylock level, perform the above procedure
using the remote control.
• If a password has been set and the keylock level selected,
the password must be entered before adjusting the keylock
level.
Checking the Lamp UsageTime
Projector
Remote control
This function allows you to check the accumulated lamp
usage time.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1
2
1 Press MENU.
2 Press ß/© to select “Options”. The lamp usage
time will be displayed.
• It is recommended that the lamp be replaced after
approximately 1,400 hours of usage. See pages 48 and 49
for lamp replacement.
(GUI) On-screen Display
E-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Reverse/Invert Image Function
Projector
Remote control
This projector is equipped with a reverse/invert image
function which allows you to reverse or invert the pro-
jected image for various applications.
Description of Projected Images
1, 5
Selected item
Projected image
Front
Normal image
2, 3
Ceiling
ם Front Rear
Inverted image
Reversed image
4
Ceiling
ם Rear Reversed and inverted image
(GUI) On-screen Display
When “Front” is selected.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
2 Press ß/© to select “PRJ Mode”.
3 Press ∂/ƒ to select the desired projection mode.
4 Press ENTER to save the setting.
When “Ceiling
ם Front” is selected. 5 To exit from the GUI, press MENU.
• This function is used for the reversed image and ceiling-
mount setups. See page 20 for these setups.
When “Rear” is selected.
When “Ceiling
ם Rear” is selected. E-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Presentation Tools
Projector
Remote control
This projector is equipped with presentation tools that
can be used to emphasize keypoints within your
presentation.
2, 4
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
3, 5
1 Press TOOLS to display the presentation tools
menu window on the screen.
2 Press ∂/ƒ/ß/© to select the desired tool and
1
6
color.
3 Press ENTER to select it.
On-screen Display
4 Once the tool is displayed on the screen, press
∂/ƒ/ß/© to move it around the screen.
5 Press ENTER to stamp the tool on the screen.
6 Press UNDO to individually delete tools stamped
on the screen.
Menu Window
• You can stamp each tool as many times as you want on the
screen.
• To clear all the stamped presentation tools from the screen,
press ∂/ƒ/ß/© to select “ ” and then press ENTER.
Red
Green
Blue
Yellow
Orange
White
Black
Projector
Remote control
Displaying the Break Time
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
2, 4
1 Press TOOLS to display the presentation tools
menu window on the screen.
2 Press ∂/ƒ/ß/© to select “ ” in the menu
3
window.
1, 5
3 Press ENTER to start counting down the break
time.
4 Press ∂ to increase or ƒ to decrease the break
When selecting Sharp default image
time.
5 Press TOOLS to return to normal screen.
• The break time is displayed against the background image
selected in “Selecting a Startup Image”. (See page 38.)
E-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Status Function
This function can be used to display all the adjusted
settings on the screen simultaneously.
Projector
Remote control
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1 Press MENU.
1, 4
2
2 Press ß/© to select “Status”.
3 Press ENTER to display all the adjustment
3
settings.
4 To exit from the GUI, press MENU.
(GUI) On-screen Display
2
3
E-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance &
Troubleshooting
E-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Filter Maintenance
• This projector is equipped with four air filters to ensure the optimal operating condition of the projector.
• The air filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used
in a dusty or smoky location.
• Have your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center exchange the filter
(PFILD0076CEZZ) when it is no longer possible to clean it.
Bottom View
Air filters
(not removable)
Air filter
Cleaning and replacing the bottom air filter
Unplug the power
cord.
Remove the bottom
filter cover.
Remove the air filter.
1
2
3
Turn over the projector. Press the
tab and lift open the filter cover
in the direction of the arrow.
Grasp the air filter between your
fingers and lift it out of the filter
cover.
Tab
Replace the filter
cover.
Clean the air filter.
Replace the air filter.
4
5
6
Clean the dust off the air filter
and cover with a vacuum
cleaner extension hose.
Place the air filter underneath
the tabs on the filter frame.
Insert the tab on the end of the
filter cover into the filter cover
opening and press the filter
cover into position.
Tab
• Be sure the filter cover is securely installed. The power will not turn on unless it is correctly installed.
Cleaning the bottom air filters (not removable)
If dust or dirt has collected inside the air filters, clean the filters with a vacuum cleaner extension hose.
E-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp/Maintenance Indicators
• The warning lights on the projector indicate problems
inside the projector.
Maintenance Indicators
• There are two warning lights: a TEMPERATURE
WARNING indicator which warns that the projector is
too hot, and a LAMP REPLACEMENT indicator which
lets you know when to change the lamp.
• If a problem occurs, either the TEMPERATURE
WARNING indicator or the LAMP REPLACEMENT
indicator will light up red. After turning off the power,
follow the procedures given below.
POWER
indicator
LAMP
REPLACEMENT
indicator
TEMPERATURE
WARNING
indicator
Maintenance Indicator
Condition
The internal
temperature is
Problem
Possible Solution
• Blocked air intake.
• Relocate the projector to an area with
proper ventilation.
TEMPERATURE
WARNING indicator
abnormally high.
• Clogged air filter.
• Clean the filter.
(See page 46.)
• Cooling fan breakdown.
• Internal circuit failure.
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
• Burnt-out lamp.
• Lamp circuit failure.
• Carefully replace the lamp. (See pages 48
and 49.)
The lamp does not
light up.
LAMP REPLACE-
MENT indicator
• Take the projector to your nearest
Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
• Lamp has been used for
over 1,400 hours.
The lamp requires
replacement.
• Securely install the bottom filter cover.
POWER indicator
• The bottom filter cover is
The POWER
open.
indicator flashes in
red when the
projector is on.
• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has cooled down
completely before turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be triggered, preventing
the power from going on. Should this occur, take the power cord out of the wall outlet and put it back in again.
Lamp
The lamp in this projector operates for approximately 1,500 cumulative hours, depending on the usage environ-
ment. It is recommended that the lamp be replaced after 1,400 cumulative hours of use or when you notice a
significant deterioration of the picture and color quality. The lamp usage time can be checked with the On-screen
Display (see page 41).
CAUTION
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
• As the usage environment can vary significantly, the projector lamp may not operate for 1,500 hours.
Condition
Problem
Possible Solution
The LAMP REPLACEMENT
• Lamp has been used for over 1,400
hours.
• Purchase a replacement lamp unit
(lamp cage/module) of the current
type BQC-PGC30XU/1 from your
nearest Authorized Sharp Industrial
LCD Products Dealer or Service
Center.
indicator lights up red, and “LAMP”
and “ ” will flash in yellow in the
lower-left corner of the picture.
A significant deterioration of the
picture and color quality occurs.
• Replace the lamp. (See pages 48
and 49.) If you wish, you may have
the lamp replaced at your nearest
Authorized Sharp Industrial LCD
Products Dealer or Service Center.
The power will automatically turn
off and the projector will enter
standby mode.
• Lamp has been used for over 1,500
hours.
“LAMP” and “ ” will flash in red in
the lower-left corner of the picture,
and the power will turn off.
E-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Projection Lamp
It is recommended that the lamp be replaced after approximately 1,400 cumulative hours of use or when you
notice a significant deterioration of the picture and color quality. Carefully change the lamp by following the steps
below.
If the new lamp does not light after replacement, take your projector to the nearest Authorized Sharp Industrial
LCD Products Dealer or Service Center for repair. Purchase a replacement lamp unit (lamp/cage module) of the
current type BQC-PGC30XU/1 from your nearest Authorized Sharp Industrial LCD Products Dealer or Service
Center. Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp
replaced at your nearest Authorized Sharp Industrial LCD Products Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through an Authorized Sharp Industrial LCD
Products Dealer or Service Center. For the name of the nearest Authorized Sharp Industrial LCD Products Dealer or
Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
U.S.A. ONLY
Removing and installing the lamp unit
CAUTION
• Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely hot. Wait at least one
hour after the power cord is disconnected to allow the surface of the lamp cage to fully cool before removing the lamp
cage.
• Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of
the projector.
• To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
• Before or after replacing the lamp, be sure to clean the air filters. See page 46 for cleaning the air filters.
Turn off the power.
Disconnect the power
cord.
Remove the lamp cage
cover.
1
2
3
Press POWER OFF. Wait until
the cooling fan stops.
Unplug the power cord from the
AC socket.
Turn over the projector and
loosen the user service screw
that secures the lamp cage
cover. Then slide the cover in the
direction of the arrow.
or
User service
screw
Remove the lamp
cage.
Insert the new lamp cage.
Attach the lamp cage
cover.
4
5
6
Remove the securing screws
from the lamp cage. Hold the
lamp cage by the handle and
pull it towards you.
Press the lamp cage firmly into
the lamp cage compartment.
Fasten the securing screws.
Slide the lamp cage cover in the
direction of the arrow. Then
tighten the user service screw.
Securing
screw
Securing
screw
User service
screw
E-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Projection Lamp
Resetting the lamp timer
Connect the power
cord.
Reset the lamp timer.
1
2
Plug the power cord into the AC
socket of the projector.
While pressing ƒ, © and
ENTER on the projector, press
POWER ON on the projector.
“LAMP 0000H” is displayed,
indicating that the lamp timer is
reset.
Ł
• Reset the lamp timer only after replacing the lamp.
Using the Kensington Lock
This projector has a Kensington Security Standard
connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the
system for instructions on how to use it to secure the
projector.
Kensington Security
Standard connector
Troubleshooting
Problem
Check
Power cannot be turned on or off • Keylock level is set to “Level A” or “Level B”, preventing operation of some or all buttons (See page
using the POWER buttons (ON/
OFF) on the projector.
41.)
No picture and no sound.
• Projector power cord is not plugged into the wall outlet.
• The bottom filter cover is not securely installed.
• Selected input is wrong. (See page 17.)
• Cables incorrectly connected to rear panel of the projector. (See pages 11–15.)
• Remote control batteries have run down. (See page 8.)
• Remote control’s MOUSE/ADJUSTMENT switch is set to MOUSE.
Sound is heard but no picture
appears.
• Cables incorrectly connected to rear panel of the projector. (See pages 11–15.)
• “Contrast” and “Bright” adjustments are set to minimum position. (See page 26.)
• On-screen Display (“BLACK SCREEN”) is turned off and Black Screen function is turned on,
creating a black image. (See page 37.)
Color is faded or poor.
Picture is blurred.
• “Color” and “Tint” adjustments are not correct. (See page 26.)
• Adjust the focus. (See page 17.)
• Projection distance is too long or too short to allow for proper focus. (See page 18.)
Picture appears but no sound is
heard.
• Cables incorrectly connected to rear panel of the projector. (See pages 11–15.)
• Volume is set to minimum. (See page 17.)
An unusual sound is occasionally
heard from the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes.
This will not affect operation or performance.
Maintenance indicator lights up.
Picture noise appears.
• Refer to “Lamp/Maintenance Indicators” on page 47.
• Adjust the “Phase” setting. (See page 29.)
480P images do not appear.
• Set the resolution mode to 480P. (See page 31.)
• Change the input signal type. (See page 27.)
Color is distorted (except for
INPUT 3 (VIDEO) mode).
E-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Transporting the Projector
When transporting the projector, carry it by the carrying
handle on the side.
Using the Carrying Handle
CAUTION
• Always put on the lens cap to prevent damage to the lens
when transporting the projector.
• Do not lift or carry the projector by the lens or the lens cap
as this may damage the lens.
Carrying handle
E-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Pin Assignments
Analog Computer 1 and 2 Signal Input Ports: 15-pin mini D-sub female connector
Computer Input
Analog
1. Video input (red)
2. Video input
(green/sync on green)
3. Video input (blue)
4. Reserve input 1
5. Composite sync
6. Earth (red)
9. Not connected
10. GND
11. GND
1
12. Bi-directional data
13. Horizontal sync signal
14. Vertical sync signal
15. Data clock
5
10
15
6
11
7. Earth (green/sync on green)
8. Earth (blue)
RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable
Pin No.
Signal
CD
RD
SD
Name
I/O
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
1
2
3
4
5
6
7
8
9
1
5
Receive Data
Send Data
Input
Output
ER
SG
DR
RS
CS
CI
Signal Ground
Data Set Ready
Request to Send
Clear to Send
Output
Output
Input
6
9
RS-232C Terminal: 9-pin Mini DIN connector
Pin No. Signal
Name
I/O
Reference
8
1
2
3
4
VCC
RD
ם 3.3V (Reserved) Receive Data
Send Data
Output
Input
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
7
9
SD
Output
EXIR
Detector of Option Unit Input
(Reserved)
Signal Ground
IR Receive Signal from Input
IR Amplifier (Reserved)
6
3
5
6
SG
ERX
Connected to internal circuit
Not connected
7
8
9
RS
CS
ETX
Request to Send
Clear to Send
IR Transmit Signal
(Reserved)
Output
Input
Output
Connected to internal circuit
Connected to internal circuit
Not connected
5
4
2
1
E-51
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Port Specifications
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, sold
separately) to the projector. (See page 14 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate:
Data length:
Parity bit:
9,600 bps
8 bits
NON
Stop bit:
1 bit
None
Flow control:
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After the
projector processes the command from the computer, it sends a response code to the computer.
Command format
Return code (0DH)
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits Parameter 4-digits
Response code format
Normal response
Return code (0DH)
Problem response (communication error or incorrect command)
Return code (0DH)
O
K
E
R
R
When more than one code is being sent, send each command only after the OK response code for the previous
command from the projector is verified.
• When using the computer control function of the projector, the projector operating status cannot be read to the computer.
Therefore, confirm the status by transmitting the display commands for each adjustment menu and checking the status with
the On-screen Display. If the projector receives a command other than a menu display command, it will execute the com-
mand without displaying the On-screen Display.
Commands
EXAMPLE
• When “BRIGHT” of INPUT 1 IMAGE ADJUSTMENT is set to
מ 10. Computer
Projector
→
←
R
A
B
R
_
מ 1
0
O
K
COMMAND
PARAMETER
COMMAND
PARAMETER
CONTROL
CONTENTS
CONTROL
CONTENTS
CONTROL ITEM
CONTROL ITEM
C1 C2 C3 C4 P1 P2 P3 P4
C1 C2 C3 C4 P1 P2 P3 P4
P
P
I
O
O
R
R
V
W
W
G
G
E
R
R
B
B
D
K
A
E
E
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
0
1
1
2
1
0
*
POWER OFF (STANDBY)
POWER ON
I
A
A
A
A
A
A
A
A
A
A
A
A
A
S
S
I
I
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
*
1
2
0
1
*
RGB
INPUT 1 SIGNAL TYPE
SELECTION
POWER SETTING
I
COMPONENT
INPUT1
R
R
R
R
R
R
R
R
R
R
R
P
P
T
I
INTERLACED
INPUT 1
I/P CONVERSION
INPUT SWITCHING
INPUT CHECK
I
INPUT2
I
PROGRESSIVE
I
INPUT3 (VIDEO)
INPUT CHECK
VOLUME (00 – 60)
MUTE OFF
C
P
B
R
B
C
T
R
R
COLOR TEMPERATURE (
מ 3 – ם 3) CONTRAST (
מ 30 – ם 30) BRIGHT (
מ 30 – ם 30) RED (
מ 30 – ם 30) BLUE (
מ 30 – ם 30) COLOR (
מ 30 – ם 30) TINT (
מ 30 – ם 30) INPUT 1 DISPLAY
RESET
I
C
O
U
U
H
L
*
*
V
M
M
R
D
E
O
I
*
*
*
VOLUME
ADJUSTMENT
T
_
_
0
1
*
*
*
INPUT 1
IMAGE
ADJUSTMENT
T
MUTE ON
*
*
*
*
*
*
KEYSTONE
ADJUSTMENT
KEYSTONE
(
מ 127 – ם 127) K
L
E
Y
S
S
*
*
*
*
*
*
*
*
*
*
E
E
_
_
_
_
0
1
DIGITAL
SHIFT
DIGITAL SHIFT
(
מ 96 – ם 96) N
D
_
E-52
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Port Specifications
COMMAND
PARAMETER
COMMAND
PARAMETER
CONTROL
CONTENTS
CONTROL
CONTENTS
CONTROL ITEM
CONTROL ITEM
C1 C2 C3 C4 P1 P2 P3 P4
C1 C2 C3 C4 P1 P2 P3 P4
I
I
B
B
B
B
B
B
B
B
B
B
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D
N
N
A
A
A
A
E
S
S
I
I
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
_
*
_
_
_
_
*
1
2
0
1
*
RGB
M
M
M
M
M
E
E
E
E
E
S
S
S
S
S
Y
Y
Y
Y
Y
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
2
3
4
5
AUTO
INPUT2 SIGNAL TYPE
SELECTION
COMPONENT
PAL (50/60 Hz)
SECAM
VIDEO
SYSTEM
SELECTION
R
R
R
R
R
R
R
R
R
R
R
V
V
V
V
V
V
V
V
V
V
V
V
A
A
A
A
A
A
A
I
P
P
T
I
INTERLACED
INPUT 2
I/P CONVERSION
I
PROGRESSIVE
NTSC 4.43
NTSC 3.58
C
P
B
R
B
C
T
COLOR TEMPERATURE (
מ 3 – ם 3) CONTRAST (
מ 30 – ם 30) BRIGHT (
מ 30 – ם 30) RED (
מ 30 – ם 30) BLUE (
מ 30 – ם 30) COLOR (
מ 30 – ם 30) TINT (
מ 30 – ם 30) INPUT 2 DISPLAY
RESET
*
*
VIDEO
CONFIRMATION
S
Y
S
E
_
_
_
_
DISPLAY
R
D
E
O
I
*
*
*
*
*
*
I
M
M
M
M
M
M
M
P
B
B
B
B
S
S
S
O
O
Y
L
G
G
G
G
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
2
3
4
1
2
3
0
1
*
SHARP
INPUT 2
IMAGE
ADJUSTMENT
*
*
*
I
CUSTOM
BLUE
BACKGROUND
SELECTION
*
*
*
I
*
*
*
I
NONE
R
R
I
E
E
P
P
T
I
_
_
_
_
_
*
_
_
_
_
*
0
1
0
1
*
I
SHARP
STARTUP
IMAGE
SELECTION
I
I
CUSTOM
NONE
INTERLACED
I
I
INPUT 3 (VIDEO)
I/P CONVERSION
I
PROGRESSIVE
A
A
K
M
M
M
M
M
M
M
M
M
M
M
G
G
G
G
G
G
G
G
R
R
R
R
R
R
R
R
R
I
W
W
L
AUTO POWER OFF
AUTO POWER ON
AUTO POWER OFF
KEYLOCK
C
P
B
C
T
COLOR TEMPERATURE (
מ 3 – ם 3) CONTRAST (
מ 30 – ם 30) BRIGHT (
מ 30 – ם 30) COLOR (
מ 30 – ם 30) TINT (
מ 30 – ם 30) SHARPNESS (
מ 30 – ם 30) RED (
מ 30 – ם 30) BLUE (
מ 30 – ם 30) VIDEO DISPLAY
P
*
*
E
LEVEL SETTING (0
ENGLISH
מ 2) R
O
I
*
*
*
E
A
A
A
A
A
A
A
A
A
A
A
R
R
R
R
V
V
V
V
R
R
R
R
R
R
V
V
V
E
E
N
N
1
2
3
4
5
6
7
8
9
0
1
1
2
3
4
1
2
3
4
1
2
3
1
2
3
1
2
3
0
1
0
1
*
*
*
E
L
DEUTSCH
INPUT 3 (VIDEO)
IMAGE
ADJUSTMENT
*
*
*
E
L
ESPAÑOL
S
R
B
R
R
T
H
D
E
E
E
E
A
E
E
J
*
*
*
E
L
NEDERLANDS
FRANÇAIS
ITALIANO
*
*
*
E
L
LANGUAGE
SELECTION
*
*
*
E
L
_
_
*
_
_
*
0
1
*
E
L
SVENSKA
RESET
E
L
TREBLE (
מ 30 – ם 30) BASS (
מ 30 – ם 30) AUDIO DISPLAY
E
L
PORTUGUÊS
B
R
R
D
D
J
*
*
*
E
L
AUDIO
ADJUSTMENT
_
_
_
_
_
*
_
_
_
_
_
*
0
1
0
1
1
*
E
L
RESET
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
A
A
M
M
M
M
M
M
M
M
M
M
M
M
S
S
S
S
S
S
S
S
S
R
R
I
STANDARD
GAMMA1
GAMMA2
CUSTOM
STANDARD
GAMMA1
GAMMA2
CUSTOM
NORMAL
AUTO SYNC OFF
INPUT 1/2 GAMMA
SELECTION
INPUT AUTO
SYNCHRONIZATION
J
AUTO SYNC ON
S
L
H
P
P
E
E
S
L
K
K
O
O
I
AUTO SYNC START
CLOCK (
מ 150 – ם 150) PHASE (
מ 60 – ם 60) H-POS (
מ 150 – ם 150) V-POS (
מ 60 – ם 60) COMPUTER INPUT DISPLAY
RESET
C
P
H
V
R
R
M
M
B
B
B
B
D
D
A
A
INPUT 3 (VIDEO)
GAMMA
SELECTION
I
_
*
*
*
*
I
*
*
*
INPUT
ADJUSTMENT
I
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
*
INPUT 1 RESIZE
INPUT 2 RESIZE
I
WIDE/FIT TO SCREEN
DOT BY DOT/NORMAL (WIDE)
NORMAL
M
M
I
SAVE SETTING (1–7)
SELECT SETTING (1–7)
BLACK SCREEN OFF
BLACK SCREEN ON
BLACK SCREEN DISPLAY OFF
BLACK SCREEN DISPLAY ON
OSD DISPLAY OFF
OSD DISPLAY ON
AUTO SYNC DISPLAY OFF
AUTO SYNC DISPLAY ON
SCREEN MODE
MEMORY
E
*
M
M
M
M
M
M
M
M
0
1
0
1
0
1
0
1
WIDE/FIT TO SCREEN
DOT BY DOT/NORMAL (WIDE)
NORMAL
BLACK SCREEN
I
I
INPUT 3 (VIDEO)
RESIZE
I
WIDE
I
NORMAL (WIDE)
REVERSE OFF
REVERSE ON
ON-SCREEN DISPLAY
SETTING
I
I
I
S
S
I
SCREEN SETTING
I
I
INVERT OFF
I
I
INVERT ON
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range
indicated in brackets under CONTROL CONTENTS.
• INPUT ADJUSTMENT can only be set in the displayed computer mode.
E-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Horizontal Frequency: 15–126kHz
Vertical Frequency: 43–200 Hz
Pixel Clock: 12–230 MHz*
Compatible with sync on green and composite sync signals
UXGA (1,600
ן 1,200) compatible in advanced intelligent compression AICS (Advanced Intelligent Compression and Expansion System) resizing technology
PC/
MAC/
WS
Horizontal
Vertical
PC/
MAC/
WS
Horizontal
Vertical
VESA
Standard
VESA
Standard
Frequency Frequency
Frequency Frequency
Resolution
Display
Resolution
Display
(kHz)
27.0
31.5
37.9
27.0
(Hz)
60
(kHz)
54.3
64.0
64.1
67.5
75.7
77.3
90.2
111.1
54.8
65.9
67.4
64.0
74.6
78.1
75.7
91.1
108.4
74.7
75.0
81.3
87.5
90.1
93.8
106.3
(Hz)
60
70
72
75
80
85
100
120
60
72
74
60
70
74
75
85
100
52
60
65
70
72
75
85
640
ן 350 70
85
ן ן 60
ן 720
ן 350 1,152
ן 864 31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
47.9
53.0
61.8
78.5
80.9
100.4
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
77.2
98.3
102.1
125.6
35.5
40.3
56.5
58.1
68.7
73.5
77.2
80.6
98.8
113.2
125.6
70
60
640
ן 400 70
85
60
SXGA
Advanced
Intelligent
Compression
720
ן 400 1,152
ן 882 70
ן ן ן 85
50
ן ן PC
VGA
60
70
1,280
ן 1,024 72
75
ן ן 85
640
ן 480 90
Upscale
ן ן ן 100
120
150
160
200
50
UXGA 1,600
ן 1,200 Intelligent
Compression
ן ן PC
ן ן 56
PC/
MAC 13"
VGA
XGA
640
ן 480 34.9
67
Upscale
True
60
70
48.4
60.0
60
75
ן ן PC/
MAC 19"
1,024
ן 768 72
ן ן ן 75
Advanced
Intelligent
Compression
PC/
MAC 21"
ן SVGA 800
ן 600 85
SXGA 1,280
ן 1,024 80.0
75
90
46.8
49.6
75
75
100
120
150
160
200
43
Upscale
MAC 16" SVGA 832
ן 624 MAC 21" SXGA 1,152
ן 870 68.5
78.1
75
72
HP (WS)
PC (WS)
WS
1,280
ן 1,024 ן 60.0
85.9
53.5
76.8
60.9
71.9
60
85
50
72
66
76
1,280
ן 960 Advanced
Intelligent
Compression
ן ן ן 50
SXGA
SGI (WS)
SUN (WS)
1,280
ן 1,024 70
72
1,152
ן 900 85
XGA 1,024
ן 768 90
True
96
100
120
140
150
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how
to change display modes can be found in your notebook computer’s operation manual.
• This projector can receive 640
ן 350 VESA format VGA signals, however, “640 ן 400” will appear on the screen. • When receiving 1,600
ן 1,200 VESA format UXGA signals, sampling occurs and the image is displayed with 1,024 lines, causing part of the image to be blocked.
E-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product type LCD Projector
Model PG-C30XU
Video system PAL/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I
Display method LCD panel
ן 3, RGB optical shutter method LCD panel Panel size: 0.9Љ (13.9 [H]
ן 18.5 [W] mm) Display method: Translucent TN liquid crystal panel
Drive method: TFT (Thin Film Transistor) Active Matrix panel
No. of dots: 786,432 dots (1,024 [H]
ן 768 [V]) Lens 1–1.3
ן zoom lens, F1.7–2.0, f ס 33–43 mm Projection lamp 200 W NSH lamp
Contrast ratio 200:1
Video input signal RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)
S-video input signal 4-pin Mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Horizontal resolution 580 TV lines (video input), 700 TV lines (DTV 720P input, Dot by Dot)
Audio output 2 W (monaural)
Computer RGB input signal 15-PIN MINI D-SUB CONNECTOR (INPUT 1, 2):
RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive,
75 Ω terminated
STEREO MINIJACK: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only)
VERTICAL SYNC. SIGNAL: Same as above
Pixel clock 12–230 MHz
Vertical frequency 43–200 Hz
Horizontal frequency 15–126 kHz
Computer control signal 9-pin Mini DIN male connector (RS-232C Input Port)
Speaker system 3 3⁄32Љ (8 cm) round
Rated voltage AC 110–120/220–240 V
Input current 3.0 A/1.5 A
Rated frequency 50/60 Hz
Power consumption 300 W
Operating temperature 41°F to 104°F (
ם 5°C to ם 40°C) Storage temperature
מ 4°F to 140°F (מ 20°C to ם 60°C) Cabinet Plastic
I/R carrier frequency 38 kHz
Laser pointer of remote control Wave length: 650 nm / Max. output: 1 mW / Class II Laser Product
Dimensions (approx.) 9 1⁄64Љ (W)
ן 4 49⁄64Љ (H) ן 12 13⁄64Љ (D) (229 ן 121 ן 310 mm) (main body only) 9 19⁄32Љ (W)
ן 5 9⁄32Љ (H) ן 14 7⁄64Љ (D) (243.5 ן 134 ן 358.4 mm) (including adjustment feet and projecting parts)
Weight (approx.) 18.52 lbs. (4.8 kg)
Supplied accessories Remote control, Two AA size batteries, Power cord (11Ј 10Љ, 3.6 m), Computer RGB cable
(9Ј 10Љ, 3 m), Computer audio cable (9Ј 10Љ, 3 m), PS/2 mouse control cable (3Ј 3Љ, 1 m),
USB mouse control cable (4Ј 11Љ, 1.5 m), DIN-D-sub RS-232C cable (6 45⁄64Љ, 15 cm),
Remote mouse receiver, Extra air filter, Lens cap (attached), CD-ROM, LCD projector
operation manual, LCD projector quick reference, Sharp Advanced Presentation Software
operation manual
Replacement parts Lamp unit (Lamp/cage module) (BQC-PGC30XU/1), Remote control (RRMCG1579CESA),
AA size batteries, Power cord (QACCU5013CEZZ), Computer RGB cable
(QCNW-5304CEZZ), Computer audio cable (QCNW-4870CEZZ), PS/2 mouse control cable
(QCNW-5113CEZZ), USB mouse control cable (QCNW-5680CEZZ), DIN-D-sub RS-232C
cable (QCNW-5276CEZZ), Remote mouse receiver (RUNTK0673CEZZ), Air filter
(PFILD0076CEZZ), Lens cap (PCAPH1307CESB), CD-ROM (UDSKA0019CEN1), LCD
projector operation manual (TINS-7023CEZZ), LCD projector quick reference (TINS-
7025CEZZ), Sharp Advanced Presentation Software operation manual (TINS-7054CEZZ)
This SHARP projector uses LCD (Liquid Crystal Display) panels. These
very sophisticated panels contain 786,432 pixels (
ן RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment
such as large screen TVs, video systems and video cameras, there
are certain acceptable tolerances that the equipment must conform
to.
This unit has some inactive TFTs within acceptable tolerances which
may result in illuminated or inactive dots on the picture screen. This
will not affect the picture quality or the life expectancy of the unit.
If you have any questions about this matter, please call toll free 1-888-
GO-SHARP (1-888-467-4277). U.S.A. ONLY
Specifications are subject to change without notice.
E-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Rear View
Top View
23/64 (9)
23/64 (9)
3 53/64 (97.5)
3 51/64 (96.5)
25/64 (10)
2 63/64 (76)
1 11/16 (43)
3 17/64 (83)
Side View
9 19/32 (243.5)
9 1/64 (229)
13/32 (10.5)
Front View
63/64 (25)
7/16 (11)
Bottom View
Units: inches (mm)
E-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
Electronic presentations are one of the most effective
tools presenters can use to persuade an audience.
There are several ways to enhance your presentation
and maximize your effectiveness. The following are
guidelines to help you create and deliver a dynamic
presentation.
a.Types of Presentations
Computer Presentations
• To present basic information such as graphs, spreadsheets,
documents and images, use word processing and spreadsheet
applications.
30
25
20
15
10
5
• To convey more complex information and create more dynamic
presentations which allow you to control the pace of your delivery,
utilize software such as Astound®, Freelance®, Persuasion® or
PowerPoint®.
• For high-end multimedia and interactive presentations, use software
0
such as Macromedia Director®.
• Astound®, Freelance®, Persuasion®, PowerPoint® and Macromedia
Director® are trademarks of their respective companies.
Video Presentations
Use of video equipment, such as a VCR, DVD player and laser disc
player, can be effective for delivering instructional or illustrative
information that is difficult to present.
Digital Cameras and Personal Digital Assistants
(PDAs)
For highly compact and portable presentations, digital still cameras,
digital video cameras, document cameras and PDAs are ideal for
transferring data without cumbersome conversions.
Multimedia Presentations
You can integrate all of the above methods for a full multimedia
presentation including video, audio, computer applications and World
Wide Web information.
b. Creative Presentations
Oftentimes presenters do not take advantage of the many
subtle ways they can manipulate their electronic slides to more
effectively persuade the audience.
Color has a great effect on the audience during a presentation.
When used correctly and legibly, studies show that
background and foreground colors establish an emotional
tone for a presentation, help viewers understand and retain
information, and influence an audience to take a desired
course of action.
Color Considerations
• Choose legible colors.
• Text and graphics colors need sufficient contrast.
• Use darker colors for the background since a lighter background
can create uncomfortable glare. (Yellow on black creates an ideal
contrast.)
Yellow
on Black
E-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
• Background colors can subconsciously affect the audience:
Red—increases viewers’ pulse and breathing and
encourages risk taking but can also be associated with
financial loss.
Red
Blue
Blue—has a calming and conservative affect on the
audience but can also create boredom among corporate
audiences that are often inundated with this background
color.
Green—stimulates interaction.
Green
Black
Black—conveys finality and certainty. Use it as a transitional
color between slides when moving from one idea to another.
• Foreground colors create a major impact on how well an
audience understands and remembers a message.
• Use one or two bright colors for emphasis.
• Highlight important messages.
• The eye has a difficult time reading certain colored text on
certain colored backgrounds. For example, text and
background colors in red and green, and blue and black
make for difficult viewing.
• Colorblind individuals may find it difficult to distinguish
between red and green, brown and green, and purple and
blue. Avoid using these colors together.
Fonts
Presentation from SHARP
f
o
pe
ty
pe
y
ty
an
f
s
in
o
ke
ista
n
lectio
se
to
ard
m
nts
on
fo
m
om
c
t
os
e
nta
m
tio
f
th
e
re
o
e
On
p
th
th
d.
al is
o
rea
isu
m
n
s
v
r
o
h
se
re
,
in
• One of the most common mistakes in any type of
presentation visual is the selection of type fonts that are too
small, too thin, or too difficult to read.
all, to
o
to
at
a
th
• If you are not sure how well a given font will read on a screen
at various sizes, try this: Draw a 6Љ
ן 8Љ box on a piece of paper and print out several lines of text inside the box with
your computer printer at 300 or 600 dpi resolution. Vary the
sizes of text to simulate headline, body and text call-outs
for any charts or graphs. Hold the printout at arm’s length.
This is how your text will look on a 4Ј (1.2 meter)-wide screen
at 10Ј (3 meters), on a 7.5Ј (2.3 meter)-wide screen at 20Ј
(6.1 meters) and a 12Ј (3.7 meter)-wide screen at 30Ј (9.1
meters). If you cannot read the text easily, you should put
less copy on your visuals or use larger typefaces.
• Design your visuals so that they are visible by the viewer in
the last row.
• Nothing will ruin your presentation faster than misspelled
words. Take the time to proofread and edit your work before
your visuals become a permanent part of your presentation.
• Mixed case text is easier to read than text which is displayed
in capital letters.
• Another important attribute of fonts is whether any particular
face is serif or sans-serif. Serifs are small, usually horizontal
cross strokes that are added to the end of a letter’s main
strokes. Because of their ability to coax the eye along the
line of type, fonts with serifs are generally acknowledged to
be more readable.
Sans-serif
Serif
E-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
c. Set-Up
Good
Bad
Good
When giving a presentation, you need to set the stage both
figuratively and literally for success. The way you set up a
presentation room will have a great impact on the audience’s
perception of you and your message. By manipulating the
placement and use of the following tools, you will improve the
impact of your presentation.
Presentation from SHARP
Lighting—Good lighting is an important component of a
successful presentation. You should strive to create an unequal
distribution of light. An audience should always see as much
of the presenter’s face as possible, so most of the light should
be focused on you. Because it is important for you to be able
to read the audience’s faces and body language, some light
should be shed upon them. However, no light should shine
on the screen.
30
25
20
15
10
5
0
Stage— When presenting on the same level surface that your
audience is on, most people can only see the top one-third of
your body. Therefore, it is recommended that when giving a
presentation to an audience of 25 or more, you stand on a
stage or platform. As more of your body is visible, the easier
it is to communicate with an audience.
Podiums—The best presenters avoid podiums because they
hide 75% of the body and restrict movement. However, many
people feel more comfortable with a podium to hold their notes
and hide their discomfort. If you must use a podium, angle it
at 45 degrees to the audience so that you are not completely
hidden.
Visuals—It is imperative that you make sure your visuals are
large enough and projected far enough for the audience to
see. Eight times the height of an image is the optimal viewing
distance to read 24 point type. The bottom of a screen should
be at least 6Ј (1.8 meters) above the floor.
Screen—The screen should always be in the center of the
room so that all audience members can see it. Because people
read from left to right, you should always stand to the
audience’s left when discussing visuals.
Seating—Arrange seating according to the dynamics of your
presentation. If the presentation is more than half-a-day, use
classroom style seating—a chair and a desk. If you would
like to encourage audience interaction, use chevron seating,
angling the chairs into a “V” shape. When you have a very
small audience, a “U” shaped arrangement will increase
interchange.
E-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to Effective Presentations
d. Rehearsing & Delivery
• The best time to rehearse is the day or evening before,
not a couple of hours before, and the best place to
rehearse is in the actual room. Rehearsing a speech
in a small office is not the same as standing up in
front of 100 people in a hotel ballroom or classroom.
• Due to varying processor speeds of computers,
practice your slide transitions for proper timing.
• Whenever possible, set up your equipment well in
advance to allow adequate time to resolve any
unexpected issues such as lighting, power, seating
and audio.
• Thoroughly check every piece of equipment you bring
along. Make sure you have fresh batteries in your
remote controls and laptop computer. Fully charge
your computer’s battery before the presentation and
connect your AC adaptor for added safety.
• Make sure you are completely familiar with the control
panel on your projector and remote controls.
• If you are using a microphone, check it out before
hand and walk around to see where you might have
problems with feedback. Avoid standing in these
problem areas during your presentation.
e. Presentation Tips
• Before beginning, visualize yourself delivering an
outstanding presentation.
• Know your speech, memorizing at least the first three
minutes of your presentation will allow you to focus
on your rhythm and pacing.
• Speak to early arrivals to help you build a rapport
with the audience and make you feel more
comfortable.
• Do not be overly dependent on your visuals by reciting
what your audience is already reading. Know your
material well enough to be able to deliver the
presentation with ease. Use your visuals to emphasize
keypoints.
• Be sure to project your voice clearly and use eye
contact to maintain audience attention.
• Do not wait until halfway through your presentation to
get your point across. If you wait and try to create a
“build-up”, you may lose some of your audience along
the way.
• Keep your audience’s attention. As most people only
focus for 15 to 20 minutes during a one-hour
presentation, it is important to recapture their attention
periodically. Use phrases like, “This is critical to my
point” or “This is absolutely fundamental” to remind
them you are saying something they need to hear.
E-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Anti-aliasing digital keystone correction
Function to digitally correct a distorted image when the projector is set up at an angle.
Aspect ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4 : 3. There are also wide
images with an aspect ratio of 16 : 9 and 21 : 9.
Auto sync
Optimizes projected computer images by automatically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being input.
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
Compatibility
Ability to use with various image signal modes.
Composite sync
Signal combining horizontal and vertical sync pulses.
Dot by dot
Mode that projects images in their native resolution.
Fit to screen
Function to adjust an image without a 4 : 3 aspect ratio, and project it in a 4 : 3 ratio.
Freeze
Function to freeze a moving image.
GUI
Graphical User Interface. User interface with graphics that allow easier operation.
I/P conversion
Function to convert an image between “Interlaced” and “Progressive” scan displays.
Intelligent compression and expansion
High quality resizing of lower and higher resolution images to fit the projector’s native resolution.
Magnification
Digitally zooms in on a portion of an image.
PDF
Portable Document Format. Documentation format used to transfer text and images from the CD-ROM.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the
projected image typically displays horizontal flicker.
Presentation tools
Helpful tools used to emphasize keypoints throughout a presentation.
RS-232C
Function to control the projector from the computer by using the RS-232C ports on the projector and computer.
Startup image
The image displayed when the projector is turned on.
Status function
Displays the settings of each adjustment item.
Sync
Synchronizes the resolution and phase shift of two signals. When receiving an image with a resolution different from that of
the computer, the projected image may be distorted.
Sync on green
Video signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin.
Wireless mouse
Function to operate the mouse control of a computer with the supplied remote control.
XGA resolution
Resolution with 1,024
ן 768 pixels that uses the signal of an IBM/AT compatible (DOS/V) computer. E-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
M
AC socket......................................................................... 11
ADJUSTMENT buttons..................................................... 23
Air filter ............................................................................. 46
MENU button.................................................................... 23
MOUSE/ADJUSTMENT switch......................................... 21
MOUSE buttons ............................................................... 22
MUTE button .................................................................... 17
Anti-aliasing digital keystone correction ..........................
3
Aspect ratio...................................................................... 36
Audio adjustments ........................................................... 28
AUDIO INPUT 3 terminals................................................ 13
AUDIO INPUT terminal for INPUT 1, 2 ............................. 11
AUDIO OUTPUT terminal................................................. 14
Automatic power shutoff function .................................... 39
Auto sync adjustment ...................................................... 32
AUTO SYNC button.......................................................... 32
O
On-screen display language ........................................... 25
OUTPUT port for INPUT 1, 2 ............................................
7
P
PDF ..................................................................................
6
Phase ............................................................................... 29
Picture adjustments ......................................................... 26
POWER buttons ............................................................... 16
Power cord ....................................................................... 11
POWER indicator ............................................................. 16
Presentation tools............................................................. 43
PS/2 mouse control cable ................................................ 15
B
Background ..................................................................... 38
BACKLIGHT button.......................................................... 22
BLACK SCREEN button ................................................... 37
C
R
Carrying handle ............................................................... 50
Ceiling-mount................................................................... 19
Ceiling
ם Rear ................................................................... 42 Clock ................................................................................ 29
Computer audio cable ..................................................... 11
Computer RGB cable....................................................... 11
Rear projection................................................................. 19
Remote control ................................................................. 21
Remote control sensor ..................................................... 21
Remote control signal transmitter ....................................
8
Remote mouse receiver ................................................... 15
RESIZE button.................................................................. 36
RIGHT-CLICK button ........................................................ 22
RS-232C port ................................................................... 14
Cooling fan (Exhaust vent)...............................................
Cooling fan (Intake vent).................................................. 46
5
D
S
DIN-D-sub RS-232C cable............................................... 14
Dot by dot ........................................................................ 36
Speaker............................................................................
7
Startup image .................................................................. 38
Status function ................................................................. 44
S-VIDEO INPUT terminal.................................................. 13
Sync ................................................................................. 32
Sync on green .................................................................. 51
E
ENLARGE button ............................................................. 34
ENTER button................................................................... 23
Extra air filter .................................................................... 10
F
T
Fit to screen ..................................................................... 36
Foot release ..................................................................... 19
FREEZE button................................................................. 33
TEMPERATURE WARNING indicator ............................... 47
TOOLS button .................................................................. 43
U
G
UNDO button ................................................................... 20
USB mouse control cable ................................................ 15
GAMMA button ................................................................ 35
GUI (Graphical User Interface)........................................ 23
V
I
VIDEO INPUT 3 terminal .................................................. 13
VOLUME buttons ............................................................. 17
INPUT 1 port .................................................................... 11
INPUT 2 port .................................................................... 11
INPUT button.................................................................... 17
W
Wireless mouse ................................................................ 21
Intelligent compression and expansion ...........................
3
I/P conversion .................................................................. 28
X
XGA resolution .................................................................
3
K
Kensington Security Standard connector ........................ 49
KEYSTONE button ........................................................... 19
L
LAMP REPLACEMENT indicator...................................... 47
LASER POINTER button................................................... 22
Laser pointer window.......................................................
5
LEFT-CLICK button .......................................................... 22
Lens cap .......................................................................... 50
E-62
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharper Image Electric Steamer TI150 User Manual
Snell Acoustics Speaker AMC 680 User Manual
SonicWALL Network Card TZ 150 Wireless User Manual
Sony Laptop PCG 505TR User Manual
Sony MP3 Player D 303 User Manual
Sony Personal Computer V G C J S 2 0 0 User Manual
Sony Speaker System SS NX1 User Manual
Sub Zero Refrigerator 650G User Manual
Sunbeam Electric Steamer FOOD STEAMER User Manual
Swisher Log Splitter LS11534 User Manual