Planning Information
Built-In Model 650G
Over-and-Under Refrigerator/Freezer with Glass Door
Front venting allows
unit to be completely
built in
Hermetically sealed
refrigeration units
Serial and model
number plate
Lighted electronic
control panel
Triple-pane
UV resistant low-
energy glass door
Adjustable spill-proof
glass shelves
Model 650G/F
Framed
Egg container
High humidity
crisper drawer
Automatic ice maker
Model 650G/O
Four-sided
Magnetic gaskets
Overlay
Two-tier wire
Door closers
storage baskets
Removable kickplate
Full-extension roll-out
freezer drawer
(Stainless steel design shown)
Model 650G/S (P/B)
Stainless Steel
With the installation of a harness kit, these
appliances are Star-K compliant to meet strict
religious regulations in conjunction with specific
instructions found on star-k.org. You may purchase
this harness kit through your Sub-Zero dealer.
To obtain local dealer information, visit the Locator
section of our website, subzero.com.
The Sub-Zero Model 650G over-and-
under refrigerator/freezer with glass door
is available in your choice of the framed,
overlay or stainless steel design application.
Three stainless steel finishes are offered—
classic (/S), platinum (/P) and carbon (/B).
We now offer our popular 36" (914) wide over-and-
under refrigerator/freezer unit with a glass door, Model
650G. While the door shelves have been eliminated for
a clean look, you do not sacrifice storage space
because we have made the interior shelves that much
deeper. It’s the logical step from the professionals in
built-in refrigeration.
Dimensions in parentheses are in
millimeters unless otherwise specified.
1
11/06
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
S P E C I F I C A T I O N S
Model 650G
Over-and-Under Refrigerator/Freezer
with Glass Door
Overall Width
36" (914)
84" (2134)
Overall Height
M O D E L O P T I O N S
Framed Design
Overall Depth
24" (610)
650G/F
650G/O
650G/S
650G/P
650G/B
Refrigerator Capacity
Freezer Capacity
16.0 cu ft (453 L)
4.9 cu ft (139 L)
Overlay Design
Classic Stainless Steel
Platinum Stainless Steel
Carbon Stainless Steel
Minimum Height (levelers in)
Door Swing Clearance
83" (2108)
361/16" (916)
Electrical Requirements
Plumbing Requirements
Water Supply
115 V AC, 60 Hz, 15 amp circuit
1/4" copper line
You must allow 90 days from order to
delivery for platinum and carbon finishes.
20–100 psi
Annual Energy Usage
565 kWh / $52
A C C E S S O R I E S
(based on 9.06 cents per kilowatt hour)
Louvered, panel or stainless steel
grilles in 1" (25) increments from
10" (254) to 15" (381) high
Shipping Weight
Framed – 523 lbs (237 kg)
Overlay – 523 lbs (237 kg)
Stainless Steel – 529 lbs (240 kg)
Grille panels for framed design in
white, almond and classic stain-
less steel
Special Note
Model 650G has a triple-pane
UV-resistant, low-energy glass door
Specifications are subject to change without notice.
Side panels in white, almond and
classic stainless steel
Stainless steel and polished
chrome handles for overlay design
Roll-out deli basket
Dozen egg container with lid
Accessories are available through your
Sub-Zero dealer. To obtain local dealer
information, visit the Locator section of
our website, subzero.com.
Dimensions in parentheses are in
millimeters unless otherwise specified.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
I N S TA L L A T I O N S P E C I F I C A T I O N S
24"
(610)
ROUGH
OPENING
DEPTH
EXTEND WATER LINE
APPROX. 36" (914)
FROM BACK WALL
SHUT-OFF
VALVE
TOP VIEW
7"
E
(178)
6"
(152)
LOCATE ELECTRICAL
WITHIN SHADED AREA
1
35 /2"
(902)
ROUGH OPENING WIDTH
3
1
83 /4"
75 /2"
(2127)
(1918)
ROUGH
OPENING
HEIGHT
WITH
STANDARD
11" (279)
GRILLE
LOCATE WATER SUPPLY
WITHIN SHADED AREA
3"
(76)
18"
6"
(457)
(152)
W
FRONT VIEW
D I M E N S I O N S
Finished Rough Opening Width
Finished Rough Opening Height
Finished Rough Opening Depth
Location of Electrical
351/2" (902)
833/4" (2127)
24" (610)
Within upper shaded area
Within lower shaded area
Location of Water Supply
See Installation Instructions shipped with unit for detailed specifications.
Refer to the Sub-Zero Design Guide pdf file for additional specifications.
Dimensions in parentheses are in
millimeters unless otherwise specified.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
I N S TA L L A T I O N N O T E S
Refer to the illustrations and specifications
for overall dimensions, finished rough opening
dimensions and installation specifics.
A line filter is required when water condi-
tions have a high sediment content. The ice
maker operates on water pressure of 20 psi
(1.4 bar) to 100 psi (6.9 bar). In some cases a
reverse osmosis water filter system may not be
able to maintain the minimum water pressure
consistently.
Allow the door to open a minimum of 90˚ or
you'll have problems removing drawers. With
the door opening at 90˚, you may have to move
drawers slightly to clear the door interior. Refer
to the minimum door swing clearance in the
specifications chart.
The water line should be routed up through
the floor within 1/2" (13) from the back wall and
no higher than 3" (76) off the floor. If you have
to come through the wall, make sure the water
line is no more than 3" (76) from the floor.
Locate water supply within the shaded area
shown in the installation illustration.
For corner installations, allow for a minimum
3" (76) filler so that the door can open to 90˚.
If you're using raised panels, consider using a
wider filler.
Be sure to add the filler strip width to your
finished rough opening dimension. In any side-
by-side installation without a filler strip, add an
additional 1/2" (13) to your combined numbers.
This will allow for the proper width.
Regardless of the routing, allow 3' (.9 m) of
excess copper tubing to remain outside the wall
or floor for easy connection to the unit.
A 115 volt, 60 Hz, 15 amp electrical supply
is required. The supply circuit for this appliance
must be protected by a 15 amp fuse or circuit
breaker. It is recommended that a separate
circuit, serving only this appliance, be provided.
Refer to the full-scale illustrations at the end
of this section for specifics on door openings
and filler size alternatives.
If your client has chosen the stainless steel
design, the unit will be shipped complete with
wrapped stainless steel doors and handle
hardware. You will not have to install front
panels.
All Built-In models are equipped with a 6'
(1.8 m) power supply cord with a 3-prong
grounding plug which must be plugged into a
mating 3-prong grounding type wall receptacle.
Locate electrical within the shaded area shown
in the installation illustration.
If your client has chosen the framed or
overlay design, you will be adding front panels
to give the unit the custom Sub-Zero look. The
overlay design also allows you to add your own
handles, or you may choose accessory handles
available through your Sub-Zero dealer. Refer to
pages 6–11 for detailed information on adding
panels.
You must follow all National Electrical Code
regulations. In addition, be aware of local codes
and ordinances when installing your service.
To prevent the unit from tipping forward and
provide a stable installation, the unit must be
secured in place with an anti-tip blocking kit. If
there is a solid soffit above the unit with clear-
ance between the unit and the soffit of 1" (25)
or less, you won't need to block the unit.
The refrigerator door panel must include a
cut-out to accommodate the window. Refer to
the panel specifications for exact dimensions.
The glass portion of the door must be exposed
and not covered by any part of the panel.
For installations with clearances of more
than 1" (25), you must block the unit with the
anti-tip blocking kit (wood block and hardware)
provided with each Built-In unit.
For Built-In models with an automatic ice
maker, rough in the water supply line. Connect
a 1/4" OD copper line to the house supply, being
sure to use an easily accessible shut off valve
between the supply and the unit.
Refer to the Built-In Installation Instructions
packed with the appliance, which provides
step-by-step procedures for making sure the
unit is installed properly.
Do not use self-piercing valves. A saddle
valve kit (4200880) is available from your
Sub-Zero dealer. To obtain local dealer informa-
tion, visit the Locator section of our website,
subzero.com.
Dimensions in parentheses are in
millimeters unless otherwise specified.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
A D D I N G PA N E L S
In your plan for panels, be sure you are working with the
Sub-Zero panel design family called for in your design. If
you have chosen the stainless steel design, the unit will be
shipped complete with wrapped stainless steel doors and
handle hardware. You will not have to install front door
panels.
F R A M E D PA N E L S
If you and your client have ordered a framed or overlay
design model, you will be adding panels to give the unit
the custom Sub-Zero look. Specifications on the following
pages provide installation considerations for framed and
overlay door panels.
1
PANELS /4" (6) THICK OR LESS
Trim reveal
/4" (6) min
1
Side panels can be used with the framed, overlay and
stainless steel design applications. Refer to specifications
on page 11.
1
/4" (6) Panel
Framed door panel 1/4" (6) thick or less
F R A M E D PA N E L S
If the thickness of the custom panels is less than 1/4"
(6), they must be backed up with a sheet of shim material
to build the total thickness to 1/4" (6). If the panel is thicker
than 1/4" (6), an edge must be routed around the panel to
ensure a proper fit. Refer to the illustrations on this page.
1
PANELS THICKER THAN /4" (6)
Trim reveal
/4" (6) min
1
1
Rout to /4" (6)
IMPORTANT NOTE: Routing, recessing or optional
extended handles may be required on raised panels for
finger clearance under the handle. Refer to the full-scale
illustrations on pages 12–15.
thickness
IMPORTANT NOTE: The weight of each panel cannot
exceed 50 lbs (23 kg).
Framed door panel thicker than 1/4" (6)
The traditional framed models come with an 11" (279)
louvered grille and elegant full-length handle. Optional
extended full-length handles that provide additional finger
clearance for raised panels are available through your
Sub-Zero dealer. To obtain local dealer information, visit
the Locator section of our website, subzero.com.
For framed door panel dimensions and dimensions for the
optional panel grille for the framed application, refer to
specifications on page 7.
To install framed panels, refer to the installation instruc-
tions shipped with each unit. These instructions can also
be found on our website, subzero.com.
Dimensions in parentheses are in
millimeters unless otherwise specified.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
F R A M E D PA N E L S
The refrigerator door panel must include a cut-out to
accommodate the window. Refer to the chart below for
exact dimensions. The glass portion of the door must be
exposed and not covered by any part of the panel.
An 11" (279) louvered grille is standard on framed applica-
tions. Optional louvered grilles are available in 1" (25)
height increments from 10" (254) to 15" (381).
H
H
C
You may choose to use Sub-Zero's optional panel grille for
the framed application. Optional panel grilles are available
in 1" (25) height increments from 10" (254) to 15" (381).
Refer to the chart below for panel dimensions.
C
C
14" (356)
A
F R A M E D PA N E L D I M E N S I O N S
D
WIDTH
341/8" (867)
341/8" (867)
HEIGHT
481/16" (1221)
183/8" (467)
B
Refrigerator Door Panel
Freezer Door Panel
H
W
Handle Recess Location
A – 241/32" (610)
B – 171/16" (433)
Framed Door Panels
Framed Grille Panel
Window Cut-Out
253/8" (645)
395/16" (999)
Window Cut-Out Location
C – 43/8" (111)
D – 43/8" (111)
Maximum Weight (per panel)
50 lbs (23 kg)
F R A M E D G R I L L E PA N E L D I M E N S I O N S
WIDTH
HEIGHT
10" (254) Grille
11" (279) Grille
12" (305) Grille
13" (330) Grille
14" (356) Grille
15" (381) Grille
343/16" (868)
343/16" (868)
343/16" (868)
343/16" (868)
343/16" (868)
343/16" (868)
815/16" (227)
915/16" (252)
1015/16" (278)
1115/16" (303)
1215/16" (329)
1315/16" (354)
Dimensions in parentheses are in
millimeters unless otherwise specified.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
O V E R L AY PA N E L S
The overlay design allows decorative panels to cover the
door trim for a more seamless appearance that blends
with the design of the room. To achieve this look, the
most common way is to work with three panels—the
decorative overlay panel, a .10" (3) spacer panel and a 1/4"
(6) backer panel. Depending on your cabinet manufacturer,
this could be one panel routed for different dimensions or
more likely, three different panels.
O V E R L AY PA N E L S
Spacer Panel
.10"
Regardless of the physical construction of the panels
(routing or three panel assembly), you will need to follow
the exact dimensions and panel placement to ensure a
proper fit.
(3)
Overlay Panel
The top illustration on this page is a cross section view of
the three panel assembly showing placement of the
door/drawer/grille trim. The bottom illustration shows a
rear view of the three panel assembly and critical dimen-
sions, standard for all overlay models.
1
/4" (6) Backer Panel
5
/16" (8) min
5
/32" (4)
/16" (2)
Door/Drawer/
Grille Trim
1
Overlay models will come with no handle hardware,
because the beauty of this design is that you can match
the surrounding cabinetry hardware. These models will
come with an 11" (279) panel grille which will accept
decorative panel inserts to match the look of the door
panels. For overlay door and grille panel dimensions, refer
to specifications on page 9.
Three panel assembly—cross section
Overlay Panel
Spacer Panel
IMPORTANT NOTE: Keep in mind that the Sub-Zero door
panels have the potential for hitting adjacent cabinets
and/or countertops when they are opened. You need to be
aware of your surrounding cabinetry and space limitations
when using the overlay models. Refer to the full-scale
illustrations on pages 14–15.
Backer
IMPORTANT NOTE: The weight of each door panel
assembly cannot exceed 50 lbs (23 kg). The total thick-
ness of all panels for an overlay model must be at least
5/8" (16) thick.
3
~ /4"
Panel
(19)
1
.10" (3) /4" (6)
Three panel assembly—rear view
To install overlay panels, refer to the installation instruc-
tions shipped with each unit. These instructions can also
be found on our website, subzero.com.
Do not exceed the dimensions listed for the overlay
grille panel. The decorative panel cannot be any larger
or it may restrict the air flow to the compressor area
and cause problems with the operation of the unit.
Dimensions in parentheses are in
millimeters unless otherwise specified.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
O V E R L AY PA N E L S
The refrigerator door panel must include a cut-out to
accommodate the window. Refer to the chart below for
exact dimensions. The glass portion of the door must be
exposed and not covered by any part of the panel.
An 11" (279) panel grille is standard on overlay applica-
tions. Optional panel grilles are available in 1" (25) height
increments from 10" (254) to 15" (381).
H
H
A
A
A
O V E R L AY PA N E L D I M E N S I O N S
WIDTH
HEIGHT
Refrigerator Door Panel
Refrigerator Door Spacer
Refrigerator Door Backer
347/16" (875)
331/2" (851)
341/8" (867)
487/8" (1241)*
477/16" (1205)
481/16" (1221)
B
Freezer Door Panel
Freezer Door Spacer
Freezer Door Backer
347/16" (875)
331/2" (851)
341/8" (867)
1811/16" (475)
173/4" (451)
183/8" (467)
H
Window Cut-Out
257/16" (646)
393/8" (1000)
W
Window Cut-Out Location
A – 41/2" (114)
B – 5" (127)
Overlay Door Panels
Overlay Grille Panel
Maximum Weight (per panel assembly)
50 lbs (23 kg)
*The overlay refrigerator door panel
will require a recessed area to prevent
the unit's lower hinge plate from hitting
the door panel. Refer to page 10 for
detailed information.
O V E R L AY G R I L L E PA N E L D I M E N S I O N S
WIDTH
HEIGHT
10" (254) Grille Panel
10" (254) Grille Spacer
10" (254) Grille Backer
347/16" (875)
331/2" (851)
341/8" (867)
91/4" (235)
85/16" (211)
815/16" (227)
11" (279) Grille Panel
11" (279) Grille Spacer
11" (279) Grille Backer
347/16" (875)
331/2" (851)
341/8" (867)
101/4" (260)
95/16" (237)
915/16" (252)
12" (305) Grille Panel
12" (305) Grille Spacer
12" (305) Grille Backer
347/16" (875)
331/2" (851)
341/8" (867)
111/4" (286)
105/16" (262)
1015/16" (278)
13" (330) Grille Panel
13" (330) Grille Spacer
13" (330) Grille Backer
347/16" (875)
331/2" (851)
341/8" (867)
121/4" (311)
115/16" (287)
1115/16" (303)
14" (356) Grille Panel
14" (356) Grille Spacer
14" (356) Grille Backer
347/16" (875)
331/2" (851)
341/8" (867)
131/4" (337)
125/16" (313)
1215/16" (329)
15" (381) Grille Panel
15" (381) Grille Spacer
15" (381) Grille Backer
347/16" (875)
331/2" (851)
341/8" (867)
141/4" (362)
135/16" (338)
1315/16" (354)
Dimensions in parentheses are in
millimeters unless otherwise specified.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
O V E R L AY PA N E L S
IMPORTANT NOTE: For overlay door panels, it is neces-
sary to rout a space for the unit‘s lower hinge plate so
that it does not strike the door panel. Refer to the top
illustration on this page.
You will minimize the reveal between the bottom of the
overlay door panel and the top of the overlay drawer panel.
Refer to the bottom illustration on this page.
O V E R L AY PA N E L S
Overlay Panel
If you choose not to rout a space for the lower hinge plate,
you can reduce the total height of the overlay panel (deco-
rative panel only) by 1/2" (13).
1
/4"(6) Backer Panel
Spacer Panel
Do not exceed the overlay panel dimensions listed. If
you try to make the reveal tighter between the door
and drawer panels, the panels may hit when opening
and closing, causing possible damage to the panels and
the Sub-Zero unit.
3" (76)
1
(13)
/2"
Bottom Edge –
Hinge Side
(rear view)
3
/8" (10)
Recessed area for hinge plate
Overlay Panel
Spacer Panel
Backer
Panel
5
/16"
(8)
27
/32"
(21)
17
/32"
(13)
Reveal area for door panel
Dimensions in parentheses are in
millimeters unless otherwise specified.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
S I D E PA N E L S
Side panels can be used with the framed, overlay and
stainless steel design applications. When planning for side
panels with the installation of the Built-In model, you need
to be aware of space configuration to achieve a pleasing
fit. Depending on the exact panel you are using with your
unit, the height of the panel will vary.
S I D E PA N E L S
Cut-outs around the toe kick and grille area are required if
a 1/4" (6) thick panel will be inserted into the main frame
channel. The panel will need to be 24" (610) deep. Refer to
the illustration on this page for placement of toe kick and
grille area cut-outs. If a 3/8" (10) thick panel is used, the
panel will abut the main frame and should be 237/8" (606)
deep. The toe kick area may or may not be cut out
depending on the look you want to achieve.
131/4" (337)
1/4"(6)
237/8" (606)
BEHIND FRAME
IMPORTANT NOTE: The use of side panels may change
the width of your rough opening.
H A R D W A R E C O N S I D E R AT I O N S
Overlay models come without handle hardware. The
beauty of this design is that you can match the surround-
ing cabinet hardware. You or the cabinet manufacturer
must provide handle hardware to match the overall deco-
rating scheme.
4" (102)
3" (76)
The handle hardware must be installed before installing
the panel assembly. Use larger D-style handles. If screws
with thick heads are used, the screws will need to be
countersunk into the door before the panel is put into
place. Refer to the full-scale illustrations on pages 12–13
for handle hardware considerations.
Cut-outs for grille and toe kick area
IMPORTANT NOTE: Sub-Zero does not recommend using
single pull knobs on any of its Built-In models.
Optional stainless steel handles are available in a variety of
diameters and lengths in the classic, platinum and carbon
stainless steel finishes and polished chrome. Contact
your Sub-Zero dealer for specifics. To obtain local dealer
information, visit the Locator section of our website,
subzero.com.
Dimensions in parentheses are in
millimeters unless otherwise specified.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
H A N D L E P R O F I L E
–
F R A M E D A P P L I C AT I O N
OPTIONAL
EXTENDED
FULL-LENGTH
HANDLE
1"
2"
3"
(25)
(51)
(76)
1
1 /4"(32) PANEL
STANDARD
FULL-LENGTH
HANDLE
1"(25) PANEL
3
/4"(19) PANEL
1
/2"(13) PANEL
1
/4"(6) PANEL
1
/4"(6) FRAMED PANEL
DOOR
F U L L - S C A L E T E M P L A T E S
H A N D L E P R O F I L E
The following full-scale illustrations enable you
to understand some of the unique situations
you may face as you design the Built-In units
into homes. These templates can be easily
photocopied or used in your tracings.
The full-scale illustration above shows handle
placement for the framed application standard
full-length handle and the optional extended
full-length handle shown in the dashed line.
Dimensions in parentheses are in
millimeters unless otherwise specified.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
H A N D L E P R O F I L E
–
S TA I N L E S S S T E E L
/
O V E R L AY A P P L I C AT I O N S
STANDARD STAINLESS STEEL HANDLE
2"
3"
(51)
(76)
1
1 /4" (32) PANEL
1" (25) PANEL
3
/4" (19) PANEL
5
1
/8" (16) PANEL
/2" (13) PANEL
1
/4" (6) PANEL
DOOR
NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE
MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.
PA N E L A N D H A N D L E P R O F I L E
The full-scale illustration above shows handle
placement for the standard stainless steel
handle on the wrapped stainless steel door and
on overlay panel applications shown in the
dashed line.
IMPORTANT NOTE: For overlay applications,
the optional stainless steel handle must be
mounted on a panel at least 5/8" (16) thick.
For overlay applications, mount door handles
close to the opening edge of the door for ease
of opening.
Dimensions in parentheses are in
millimeters unless otherwise specified.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
PA N E L A N D H A N D L E P R O F I L E
–
1 3 0 ˚ D O O R O P E N I N G
130˚ DOOR OPENING
WITH 2" (51) FILLER STRIP
(TOP VIEW)
SUB-ZERO UNIT
FILLER STRIP
2" (51)
ALLOW FOR FILLER LAP
BEHIND FLANGE
DOOR CLOSED
OVERLAY PANEL
3/4" (19) THICK
(NOMINAL)
MAIN FRAME
HINGE
APPROX
PROFILE OF
STAINLESS
STEEL DOOR
AND HANDLE
STANDARD
FRAMED
FULL-LENGTH
HANDLE
DOOR OPEN @ 130˚
OPTIONAL
FRAMED EXTENDED
FULL-LENGTH HANDLE
The full-scale illustration above shows the panel
and handle profile of a 130˚ door opening with
2" (51) filler strip for framed applications.
To obtain local dealer information, visit the
Locator section of our website, subzero.com.
The full-scale illustration on the following page
lets you see what considerations you need to
make for any overlay panel applications, and
how they may interact with adjacent cabinets
and/or countertops.
Interference of door panels with handles at
maximum door swing may require use of the
90˚ door stop provided with the unit.
*Approximate thickness of wrapped
stainless steel door.
Dimensions in parentheses are in
14
millimeters unless otherwise specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
Planning Information
Built-In Model 650G
O V E R L AY PA N E L A P P L I C A T I O N
–
9 0 ˚ D O O R O P E N I N G
NOMINAL OVERALL
WIDTH OF SUB-ZERO
90˚ DOOR OPENING
(TOP VIEW)
SUB-ZERO UNIT
7
23 /8" (606) TO REAR
OF SUB-ZERO
MAIN FRAME
0" (0)
/4" (6)
1
DOOR CLOSED
1
3
/2" (25)
/4" (19)
1" (25)
HINGE
1
1 /4" (32)
1
1 /2" (38)
3
1 /4" (44)
2" (51)
1
2 /4" (57)
1
2 /2" (63)
DOOR OPEN @ 90˚
3
2 /4" (70)
3" (76)
1
3 /4" (83)
1
3 /2" (89)
OVERLAY PANEL
3/4" (19) THICK (NOMINAL)
*Approximate thickness of wrapped
stainless steel door.
Dimensions in parentheses are in
15
millimeters unless otherwise specified.
Download from Www.Somanuals.com. All Manuals Search And Download.
|