LCD PROJECTOR
PROJECTEUR LCD
PROYECTOR LCD
-
XG NV2SB
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACION
ENGLISH
FRANÇAIS
ESPAÑOL
E
F
Contents
E
• Important Information ................................................................... 1
• Important Safeguards ................................................................... 2
• Cautions Concerning the Laser Pointer........................................ 3
• Notes on Operation ...................................................................... 4
• Outstanding Features ................................................................... 4
• Location of Controls ..................................................................... 5
• Operating the Wireless Mouse Remote Control .......................... 6
• Wireless Mouse Functions ........................................................... 8
• Setting Up the Projector ............................................................... 9
• Using the Image Invert/Reverse Function .................................. 11
• Connecting the Projector (VIDEO 1, VIDEO 2) ......................... 14
• Connecting the Projector (RGB 1, 2: Computer) ....................... 15
• Input Signals (Recommended Timing) ....................................... 18
• RGB Adjustment Controls .......................................................... 19
• Basic Operation of the Projector ................................................ 21
• Adjusting the Picture .................................................................. 24
• Adjusting the Audio .................................................................... 25
• Functions on the Projector ......................................................... 26
• Air Filter Maintenance ................................................................ 29
• Lamp/Maintenance Indicators .................................................... 30
• Before Calling for Service ........................................................... 30
• Lamp Replacement .................................................................... 31
• Connection Pin Assignments ..................................................... 33
• RS-232C Terminal Specifications ............................................... 34
• Wired Remote Control Terminal Specifications ......................... 36
• Specifications ............................................................................. 37
• Dimensions ................................................................................ 38
ES
Table des matières
F
• Informations importantes.............................................................. 1
• Mises en garde importantes ......................................................... 2
• Précautions touchant le pointeur laser ......................................... 3
• Remarques sur le fonctionnement................................................ 4
• Caractéristiques spéciales ........................................................... 4
• Emplacement des commandes .................................................... 5
• Utilisation de la télécommande /souris sans fil .............................6
• Fonctions de la souris sans fil ...................................................... 8
• Installation du projecteur .............................................................. 9
• Utilisation de la fonction d’inversement/renversement ............... 11
• Branchement du projecteur (VIDEO 1, VIDEO 2) ...................... 14
• Branchement du projecteur (RVB 1, 2: Ordinateur) ................... 15
• Signaux d’entrée (synchronisation recommandée) ................... 18
• Commandes de réglage RVB ..................................................... 19
• Fonctionnement de base du projecteur ...................................... 21
• Réglage de l’image .................................................................... 24
• Réglage du son .......................................................................... 25
• Fonctions du projecteur .............................................................. 26
• Entretien du filtre à air ................................................................ 29
• Lampe/Témoins d’entretien ........................................................ 30
• Avant d’appeler un réparateur .................................................... 30
• Changement de l’unité de lampe (lampe/boîtier) ....................... 31
• Fonctions des broches du connecteur........................................ 33
• Fiche technique de la prise RS-232C ......................................... 34
• Fiche technique de la prise de la télécommande à fil ................ 36
• Fiche technique .......................................................................... 37
• Dimensions ................................................................................ 38
Indice
ES
• Información importante ................................................................ 1
• Medidas de seguridad importantes .............................................. 2
• Precauciones respecto al puntero láser ....................................... 3
• Notas acerca de la operación ....................................................... 4
• Características más sobresalientes ............................................. 4
• Ubicación de los controles ........................................................... 5
• Utilización del control remoto inalámbrico tipo ratón ................... 6
• Funciones del ratón inalámbrico .................................................. 8
• Instalación del proyector .............................................................. 9
• Utilización de la función de imagen invertida/de espejo ............ 11
• Conexión del proyector (VÍDEO 1, VÍDEO 2) ............................. 14
• Conexión del proyector (RGB 1, 2: Ordenador) ........................ 15
• Señales de entrada (tiempos recomendados)............................ 18
• Controles de ajuste de RGB....................................................... 19
• Funcionamiento básico del proyector ......................................... 21
• Ajuste de la imagen .................................................................... 24
• Ajuste del sonido ........................................................................ 25
• Funciones del proyector ............................................................. 26
• Mantenimiento del filtro de aire .................................................. 29
• Lámpara/indicadores de mantenimiento .................................... 30
• Antes de solicitar el servicio de reparación ................................ 30
• Reemplazo de la lámpara .......................................................... 31
• Asignaciones de las conexiones de clavijas ............................... 33
• Especificaciones del terminal RS-232C ..................................... 34
•
Especificaciones del terminal del control remoto con cable .......... 36
• Especificaciones ........................................................................ 37
• Diagramas acotados .................................................................. 38
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed RGB signal cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
U.S.A. ONLY
Important Safeguards
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to ensure
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD.
In order not to defeat the safeguards incorporated into this LCD Projector, observe the following basic rules for its
installation, use and servicing. For your own protection and reliable usage of your LCD Projector, please be sure to
read these “Important Safeguards” carefully before use.
1. Read Instructions—All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions—The safety and operating instructions should be retained for future reference.
3. Heed Warnings—All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions—All operating and use instructions should be followed.
5. Cleaning—Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments—Do not use attachments not recommended by the product manufacturer as they may cause
hazards.
7. Water and Moisture—Do not use this product near water – for example, near a bathtub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories—Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product
may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions, and should use a mounting accessory recom-
mended by the manufacturer.
9. A product and cart combination should be moved with care. Quick stops, excessive force,
and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation—Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the
product and to protect it from overheating, and these openings must not be blocked or covered. The open-
ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod-
uct should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
11. Power Sources—This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
12. Grounding or Polarization—This product is equipped with a three-wire grounding-type plug, a plug having a
third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection—Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Lightning—For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will pre-
vent damage to the product due to lightning and power-line surges.
15. Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
16. Object and Liquid Entry—Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
17. Servicing—Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those con-
trols that are covered by the operating instructions, as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—this indicates a need for service.
19. Replacement Parts—When replacement parts are required, be sure the service technician has used replace-
ment parts specified by the manufacturer or with the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
20. Safety Check—Upon completion of any service or repairs to this product, ask the service technician to per-
form safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting—The product should be mounted to a wall or ceiling only as recommended by the
manufacturer.
22. Heat—The product should be situated away from heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
Cautions Concerning the Laser Pointer
The laser pointer on the remote control
emits a laser beam from the laser light
window shown in the figure to the left. The
"COMPLIES WITH 21 CFR SUBCHAPTER J"
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
CAUTION
U.S.A. ONLY
TEL : 1-800-BE-SHARP
LASER RADIATION-
REMOTE CONTROL
MODEL NO. : G1414CESA
DC6V (1.5VX4PCS.)
MADE IN JAPAN
DO NOT STARE INTO BEAM
laser emitted is a class II laser; therefore,
do not look into the laser window or shine
the laser beam on yourself or other people.
The three marks to the left are the caution
labels for the laser beam.
Always use the laser pointer at tempera-
tures between 41°F and 104°F (
ם 5°C and ם 40°C). WAVE LENGTH : 670nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT FABRIQUÉ AU JAPON
AVOID EXPOSURE—
LASER RADIATION IS
EMITTED FROM THIS
APERTURE.
Caution:
• Use of controls or adjustments or perfor-
mance of procedures other than those speci-
fied herein may result in hazardous radiation
exposure.
LASER LIGHT WINDOW
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on Operation
About the Temperature Monitor Function:
• If the projector starts to overheat due to set-up problems or a dirty air filter, “TEMP.” will flash
in the upper-left corner of the picture. If the temperature continues to rise, then the lamp will
turn off, the TEMPERATURE WARNING indicator will flash, and after a 90-second cooling-off
period the power will shut off. Refer to page 30, “Maintenance Indicators,” when the “TEMP.”
warning appears in the picture.
TEMP.
• The cooling fan regulates the internal temperature, and its performance is automatically
controlled. The sound of the fan may change during operation due to changes in the fan
speed.
Outstanding Features
Allows easy projection of large screen, full-color com-
puter and video images.
• Can be projected directly onto a video screen or white
wall.
• Lightweight, convergence-free system for easy installa-
tion.
DIRECT COMPUTER COMPATIBILITY
A multi-scan RGB Input accepts signals from XGA
(1,024 dots
ן 768 lines compressed), SVGA (800 dots ן 600 lines), VGA and Mac (832 dots ן 624 lines maxi- mum) compatible computers without the need for any
additional hardware.
HIGH PICTURE QUALITY
The three LCD panels contain 485,616
ן RGB pixels to achieve exceptionally bright, high quality video images
with up to 580 scan doubled TV lines of resolution.
INTELLIGENT COMPRESSION
XGA images are compressed and projected without
image data loss.
VERSATILE REMOTE CONTROL
• Built-in wireless mouse allows simultaneous operation
of projector and computer.
• Built-in Laser Pointer for professional presentations.
FLEXIBLE USE
• In addition to the standard front projection mode, the
menu driven functions can be used to instantly reverse
the image for rear projection, and invert the image for
ceiling mounting.
• Screen projection size adjusts from 40 to 300 inches.
BUILT-IN STEREO SPEAKERS
Built in 2 W
ם 2 W stereo amplifiers and speakers elimi- nate the need for external audio components.
USE WITH “PLUG AND PLAY”
“Plug and Play” compatible with VESA DDC 1 and
DDC 2B standards.
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of Controls
FRONT VIEW
Speakers
Cautions:
• The exhaust vent, the lamp cage cover and adjacent areas may be
extremely hot during projector operation. To prevent injury, do not
touch these areas until they have sufficiently cooled.
• Allow at least 4؆ (10 cm) of space between the cooling fan (exhaust
vent) and the other nearest wall or obstruction.
Zoom ring
• If the cooling fan becomes obstructed, a protection device will
automatically turn off the projector lamp. This does not indicate a
malfunction. Remove the projector plug from the wall outlet and wait
10 minutes. Then turn on the power by plugging the cord back in.
This will return the projector to its normal mode.
Remote sensor
Lens focusing ring
Cooling fan (Intake vent)
OPERATION PANEL ON TOP OF PROJECTOR
LAMP REPLACEMENT indicator
TEMPERATURE WARNING indicator
POWER indicator
POWER
ON/OFF
LAMP
TEMP.
MUTE button
MUTE
POWER ON/OFF button
VOL
VOLUME UP-
DOWN buttons
INPUT SELECT
BLACK
SCREEN
INPUT SELECT button
MENU
BLACK SCREEN button
MENU button
ADJUSTMENT
(ß/©, ƒ/∂) buttons
ENTER
ENTER button
SIDE AND REAR VIEW
Cooling fan
Carring handle
(Exhaust vent)
COMPUTER RGB INPUT 2 connector (HD-15)
COMPUTER RGB
INPUT 1 connector
(HD-15)
COMPUTER AUDIO INPUT 1
(3.5 mm Stereo Minijack)
COMPUTER RGB
COMPUTER AUDIO
IN 2
IN 1
IN 1
IN 2
COMPUTER AUDIO INPUT 2
(3.5 mm Stereo Minijack)
COMPUTER RGB
OUTPUT
connector (HD-15)
Security Lock Anchor
AUDIO
OUTPUT
WIRED
REMOTE
OUT
This projector has a Kensington
Security Standard connector for use
with a Kensington MicroSaver
Security System. Refer to the
information that came with the
system for instructions on how to use
it to secure this model.
WIRED REMOTE
CONTROL INPUT
(3.5 mm Minijack)
PC CONTROL
1
2
VIDEO INPUT 1
COMPOSITE
Video: RCA
L
R
IN
1
AUDIO OUTPUT
(3.5 mm Stereo Minijack)
(VIDEO/COMPUTER RGB)
OFF
ON
Audio: RCA
IN
2
Note:
MAIN POWER
switch
VIDEO INPUT 2
S-Video: 4-pin mini DIN
Audio: RCA
S-VIDEO
VIDEO
L
R
• Be sure to use the Computer
Control cable when connecting
the PC CONTROL terminals.
AUDIO
110-120V/
200-240V~
AC INLET
• PC CONTROL 1:
Use the supplied computer control cable when operating the remote
control as a wireless mouse or when controlling the projector from
the RS-232C terminal.
• PC CONTROL 2:
Use the computer control cable (CTANZ0711CE01) (sold separately)
when operating the remote control as a wireless mouse.
Notes:
• RS-232C does not function when connected to PC CONTROL 2.
• See page 15 for connection.
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Wireless Mouse Remote Control
The functions of your personal computer’s mouse have been built into the remote control enabling you to operate
your projector and personal computer with the remote control.
1. Slide the MAIN POWER switch on the rear of the unit on.
2. Press the POWER ON button on the front panel of the remote control to turn the projector power on.
3. When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT switch to the MOUSE
position. When using the remote control to operate the projector, move the MOUSE/ADJUSTMENT switch to
the ADJ. position. To activate the remote control key back-light feature, press the LIGHT button on the remote
control. The colors of the buttons will change as shown in the table at the bottom of this page.
Wireless Mouse Remote Control
FRONT VIEW
SIDE VIEW
TRANSMIT indicator
MUTE button
MAIN POWER switch
of remote control
VOL
ON
Note:
• When transporting
the remote control,
turn off the MAIN
POWER switch to
avoid draining the
batteries.
MUTE
POWER ON/OFF
buttons
VOLUME UP-DOWN
buttons
OFF
BLACK
SCREEN
LASER/
MENU
LASER POINTER/MENU
button
B
BLACK SCREEN
button
MN
LEFT-CLICK button
MOUSE/ADJUSTMENT
(ß/©), (ƒ/∂) buttons
RIGHT-CLICK/ENTER
button
R-CLICK/ENTER
INPUT SELECT
DATA1
DATA2
INPUT SELECT
buttons
Remote control handling precautions
• The laser beam used in this product is harmless when
directed onto the skin, however please be careful not to
project the beam directly into the eyes. Do not stare into
the beam using an optical instrument.
VIDEO1
CHECK
VIDEO2
INPUT CHECK button
MOUSE label
• Do not expose the remote control to shocks, liquids or
high humidity.
ADJ. label
MOUSE
ADJ.
The remote control may not operate normally if exposed
to direct sunlight or other intense light sources. Should
this happen, reposition the light source or the projector.
MOUSE/ADJUSTMENT
switch
LIGHT
LIGHT button
LCD PROJECTOR
When you change the setting of the MOUSE/ADJUSTMENT switch,
the functions of certain buttons on the remote control change. You
can tell which function the button currently possesses by the color
of its back-light display.
Using the remote control in a dark
Button name
Position of MOUSE/ADJUSTMENT switch
room
MOUSE
LASER POINTER/MENU LASER POINTER (GREEN)
ADJ.
• Press the LIGHT button to turn on the back-
lights for the operation buttons for about 5 sec-
onds. The back-light colors are described in the
table to the right.
MENU (RED)
ENTER (RED)
ADJ. ß/©, ƒ/∂ (NOT LIT)
—
RIGHT-CLICK/ENTER
MOUSE/ADJUSTMENT
LEFT-CLICK
RIGHT-CLICK (GREEN)
MOUSE (NOT LIT)
ON (NOT LIT)
Note:
BLACK SCREEN
POWER ON/OFF
VOLUME UP-DOWN
MUTE
BLACK SCREEN (RED)
• If the MAIN POWER switch on the remote con-
trol is left on for more than 10 minutes without
operation, the power will automatically turn off.
To turn the power back on, press any button on
the remote control for at least one second.
DATA 1
ON (RED)
DATA 2
VIDEO 1
VIDEO 2
INPUT CHECK
E-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the optional cable with the remote control
When the remote control cannot be used due to the
range or positioning of the projector (rear projection,
etc.), connect the optional cable from the Wired Remote
Control Input jack on the remote control to the Wired
Remote Input on the rear of the projector.
TOP VIEW
REMOTE CONTROL SIGNAL
TRANSMITTER
WIRED REMOTE CONTROL
INPUT (3.5 mm Minijack)
Note:
• The signal transmitter does not function when the optional
cable is connected to the remote control.
LASER LIGHT WINDOW
Laser light shines out of this window.
The laser pointer on the remote control
emits a laser beam from the laser light win-
dow shown in the figure to the left. The laser
emitted is a class II laser; therefore, do not
look into the laser window or shine the laser
beam on yourself or other people. The two
marks to the left are the caution labels for
the laser beam.
"COMPLIES WITH 21 CFR SUBCHAPTER J"
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
CAUTION
U.S.A. ONLY
TEL : 1-800-BE-SHARP
LASER RADIATION-
REMOTE CONTROL
MODEL NO. : G1414CESA
DC6V (1.5VX4PCS.)
MADE IN JAPAN
DO NOT STARE INTO BEAM
WAVE LENGTH : 670nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT FABRIQUÉ AU JAPON
Always use the laser pointer at tempera-
tures between 41°F and 104°F (
ם 5°C and ם 40°C). REAR VIEW
Inserting the batteries
Remove the battery cover as shown and insert four AA
size batteries making sure their polarities match the (
ם ) and (
מ ) marks inside the battery compartment. Press in and
downward on
the arrow
mark and
remove.
Notes:
Incorrect use of batteries may cause them to leak or burst.
• Insert the batteries with the (
ם ) and (מ ) polarities as indi- cated.
• Remove the batteries if the remote control will not be oper-
ated for an extended period of time.
• Maintain the batteries in a clean condition.
• Do not mix different brands of batteries. The life expectancy
of the new batteries will be shortened and the old batteries
may leak.
Insert the side
tabs into their
slots and
press in the
cover until
properly
seated.
• When the batteries have been used up, remove them imme-
diately to prevent leakage and damage. Leaked battery fluid
may irritate the skin. Remove any battery fluid by wiping with
a cloth.
• Due to storage conditions and the shelf life of the supplied
batteries, they may run out after a short time. If so, replace
them with new batteries as soon as possible.
Remote control positioning
Use the remote control as shown in the figures on the left.
Transmission range
Reception range
Note:
30°
30°
• The signal from the remote control can be reflected off the
screen for easy operation. However, the effective distance of
the signal may differ due to the screen material.
Max. distance: 23
(7 m) 45°
30°
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Mouse Functions
The wireless mouse functions and laser pointer on the
remote control can help you create a more professional
presentation.
Connection Example
Rear terminals
COMPUTER RGB
COMPUTER AUDIO
IN IN
IN
1
IN
2
1
2
AUDIO
OUTPUT
WIRED
REMOTE
OUT
• By connecting the supplied computer control cable to the
PC CONTROL terminal on your projector and the supplied
mouse control cables to the mouse terminal on your
personal computer, you can use the wireless mouse on the
remote control, instead of the mouse equipped with your
personal computer, to operate your personal computer.
The wireless mouse functions will work with personal
computers compatible with IBM PS/2, serial (RS-232C) or
Apple ADB type mouse systems.
PC CONTROL
1
2
L
R
IN
1
OFF
ON
IN
2
Personal computer
S-VIDEO
VIDEO
L
R
AUDIO
110-120V/
200-240V~
To mouse terminal
Supplied
computer
control cable
Supplied mouse control cable (for IBM
PS/2, serial and Apple ADB type mouse)
Functions and Operations
VOL
ON
MUTE
MAIN POWER switch of remote control
LEFT-CLICK button
OFF
POWER ON/OFF
buttons
BLACK
SCREEN
LASER/
LASER POINTER button
MENU
B
MN
MOUSE buttons
RIGHT-CLICK button
R-CLICK/ENTER
INPUT SELECT
DATA1
DATA2
VIDEO1
CHECK
VIDEO2
MOUSE/ADJUSTMENT
switch
MOUSE
ADJ.
LIGHT
LCD PROJECTOR
• First, connect the units as shown above, and turn the projector power on.
• Second, turn the computer power on.
• Next, slide the MAIN POWER switch on the side of the remote control.
• When using the remote control as a wireless mouse, move the MOUSE/ADJUSTMENT switch to the MOUSE position.
Notes:
• In some situations the wireless mouse may be inoperable if your computer port is not correctly set-up. Please refer to your computer owners
manual for details on setting-up/installing the correct mouse driver.
• Be sure to use the computer control cable when connecting the PC CONTROL terminals.
• Do not connect or remove the mouse control cables and computer control cable to/from your computer while it is on. This may damage your
computer.
• Only one set of connection cables is supplied with your projector. For additional connection cables, contact your nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center.
• Do not connect the mouse input terminal for IBM/Mac and the mouse input terminal for PC98 simultaneously.
MOUSE buttons
By lightly pressing the up/down and right/left arrow buttons located on the front of the remote
control, you can move the mouse cursor on your monitor screen.
Note:
• The amount of pressure applied to the MOUSE button determines the speed the mouse cursor travels. Pressing
lightly on the periphery of the MOUSE button makes the mouse cursor move slowly. Pressing hard makes it move
quickly.
Mouse cursor
LEFT-CLICK button
RIGHT-CLICK button
The LEFT-CLICK button on the back of the remote control corresponds to the left button
of the mouse on two-button mouse systems.
The RIGHT-CLICK button on the front of the remote control corresponds to the right
button on two-button mouse systems.
Note: For one-button mouse systems use either the LEFT-CLICK or RIGHT-CLICK button.
LASER POINTER button Press the LASER POINTER button to activate the laser pointer.
When the button is pressed, the light stays on; when the button is released, the light
goes off. However, even when the button is pressed continuously, the light automati-
cally goes off 1 minute after it goes on. To turn it on again press the laser pointer button
one more time.
The laser pointer on the remote control emits
a laser beam from the laser light window. The
laser emitted is a class II laser; therefore, do
"COMPLIES WITH 21 CFR SUBCHAPTER J"
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
CAUTION
U.S.A. ONLY
TEL : 1-800-BE-SHARP
LASER RADIATION-
not look into the laser window or shine the
laser beam on yourself or other people. The
two marks to the left are the caution labels for
the laser beam.
REMOTE CONTROL
MODEL NO. : G1414CESA
DC6V (1.5VX4PCS.)
MADE IN JAPAN
DO NOT STARE INTO BEAM
WAVE LENGTH : 670nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT FABRIQUÉ AU JAPON
Always use the laser pointer at temperatures
between 41°F and 104°F (
ם 5°C and ם 40°C). E-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Projector
Using the Focus and Zoom
• Zoom, Focus and Reversed/Inverted Image mode functions broaden your options for projector placement.
• See pages 10, 11 and 12 for details on projector setup.
SIDE VIEW
Zoom
Ceiling setting
Invert Image
Table setting
Zoom
1. Turn on the MAIN POWER
Turn on the MAIN POWER switch on the back of the
projector.
2. Turn on the POWER
2
3
POWER
LAMP
TEMP.
Press the POWER ON/OFF button on the projector or the
POWER ON button on the remote control to turn on the
power.
POWER indicator
3. Rotating the zoom ring (from the
housed position to the wide angle
→
position)
Rotate the zoom ring on the lens until it clicks. The pic-
ture can be adjusted within the zoom range.
Zoom ring
(Lens housed)
(Wide angle)
4. Adjusting the focus
Rotate the lens focusing ring until the image on the
screen is in focus.
4
5
Lens focusing ring
5. Adjusting the zoom
Rotate the zoom ring. The picture can be adjusted to the
desired size within the zoom range.
↔
Zoom ring
(Maximum picture size)
(Minimum picture size)
(Zoom)
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Distance and Picture Size Relationship
• The zoom lens allows adjustment of the image size within the projector’s range.
• For optimum picture adjustment, the projector should be placed and adjusted at a distance between 4.6 ft
(1.4 m) and 57.4 ft (17.5 m) from the screen.
Distance from screen
Picture size: 100 inches (254 cm)
Projection distance (L)
Picture size
(diag.)
Maximum projection distance Minimum projection distance
57.4 ft (17.5 m)
38.4 ft (11.7 m)
28.5 ft (8.7 m)
19.0 ft (5.8 m)
15.1 ft (4.6 m)
11.5 ft (3.5 m)
7.5 ft (2.3 m)
35.8 ft (10.9 m)
23.9 ft (7.3 m)
17.7 ft (5.4 m)
11.8 ft (3.6 m)
9.5 ft (2.9 m)
6.9 ft (2.1 m)
4.6 ft (1.4 m)
300 inches
200 inches
150 inches
100 inches
80 inches
60 inches
40 inches
Zoom adjustment range: 19.0 ft–11.8 ft
The formula for picture size and projection
distance
y = (0.0586x
מ 0.0544) ן 3.28 y1 = (0.0367x
מ 0.0702) ן 3.28 x2: Picture size (diag.) (inches)
y : Maximum projection distance (ft)
y12 : Minimum projection distance (ft)
Lens
center
90˚
90˚
Note:
• There is an error of
ע 4 inches (ע 10 cm) in the formula above.
Minimum L: 11.8 ft (3.6 m)
Maximum L: 19.0 ft (5.8 m)
Distance between lens and screen: L
• Above is an illustration of maximum and minimum projection distances for the XG-NV2SB with a picture size of 100 inches
(254 cm). Move the projector forward or backward if the edges of the image are distorted.
Height of Projector
Adjust to match the setup configuration.
Picture size
(diag.)
Distance from lens center to
lower edge of screen (H)
300 inches
200 inches
150 inches
100 inches
80 inches
60 inches
40 inches
26.0 in. (66 cm)
17.3 in. (44 cm)
13.0 in. (33 cm)
8.7 in. (22 cm)
7.1 in. (18 cm)
5.1 in. (13 cm)
3.5 in. (9 cm)
Screen
Lens center
90˚
H
Rack/stand
Lower edge of screen
(white portion) = Standard (0) point
• Ceiling Mount
When the projector is in the inverted position, use the upper
edge of the screen as the base line.
High edge of screen
H
90˚
Note:
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.
E-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Image Invert/Reverse Function
This projector is equipped with an image invert/reverse function. The projected image can be inverted or reversed
by using the MENU button and the ADJUSTMENT ƒ/∂ and ß/© buttons.
On-Screen Display
1. Press the MENU button
1
I M A G E A D J .
With the MENU screen displayed, press the AD-
JUSTMENT ƒ/∂ buttons to select “IMAGE ADJ.”.
Then press the ENTER button to display the
“IMAGE ADJ.” screen.
[
[
[
[
]
]
]
]
B L K S C R N D I S P
I N P U T D I S P L A Y
R E V E R S E
O F F
O F F
O F F
O F F
I N V E R T
• The last MENU screen selected is indicated for about
30 seconds.
: S E L .
MENU
: A D J .
: E N D
2. Reversed Image Mode
2
I M A G E A D J .
In the “IMAGE ADJ.” menu, press the ADJUST-
MENT ƒ/∂ buttons to select “REVERSE”. Then
press the ADJUSTMENT ß/© buttons to select
“ON”. The reversed image will appear.
]
]
[
O F F
B L K S C R N D I S P
I N P U T D I S P L A Y
R E V E R S E
[
O F F
]
[
O N
]
[
O F F
I N V E R T
: S E L .
: A D J .
M E N U
: E N D
3. Inverted Image Mode
3
4
: E N D
M E N U
: A D J .
: S E L .
In the “IMAGE ADJ.” menu, press the ADJUST-
MENT ƒ/∂ buttons to select “INVERT”. Then press
the ADJUSTMENT ß/© buttons to select “ON”.
The inverted image will appear.
O N
I N V E R T
]
[
O F F
[
R E V E R S E
]
O F F
[
I N P U T D I S P L A Y
B L K S C R N D I S P
]
]
O F F
[
I M A G E A D J .
4. Reversed Inverted Image Mode
In the “IMAGE ADJ.” menu, set the “REVERSE” and
“INVERT” functions to “ON”. The reversed inverted
image will appear.
: A D J .
: S E L .
MENU : E N D
I N V E R T
O N
O N
[
]
]
R E V E R S E
[
[
[
I N P U T D I S P L A Y
B L K S C R N D I S P
O F F
O F F
]
]
I M A G E A D J .
5. Press the MENU button anytime to exit
“IMAGE ADJ.”
How to set up the projector and screen
Cautions:When setting up the projector
• For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environ-
ments, the lens and filter must be cleaned more often. Periodically the filter should be replaced and the pro-
jector should be cleaned internally. As long as the projector is properly maintained in this manner, use in these
environments will not reduce the overall operation life. Please note that all internal cleaning must be performed
by an Authorized Sharp Industrial LCD Products Dealer or Service Center.
• Do not expose to extreme heat or cold.
Operating temperature: 41°F to 104°F (
ם 5°C to ם 40°C) Storage temperature:
מ 4°F to 140°F (מ 20°C to ם 60°C) • Do not tilt the projector more than 5°.
• Position the screen so that it is not in direct sunlight or room light. Light falling directly onto the screen washes
out colors, making viewing difficult. Close the curtains and dim the lights when using the screen in a bright or
sunny room.
• The best picture will be obtained when the projector is at a 90 degree angle to the screen. Position the projector
and screen as shown.
E-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of a standard setup
TOP VIEW
SIDE VIEW
Lens center
90˚
90˚
Lens center
The projector lens should be centered
in the middle of the screen.
If the projector and screen are not
centered properly, the picture will be
distorted, making viewing difficult.
Using the horizontal reverse function makes the following setups possible.
Example of a reversed image setup
• By placing a mirror (normal flat type) in front of the lens and using the horizontal reverse function, the image reflected from
the mirror can be projected onto the screen.
• Rear projection with a rear projection screen is also possible when using the horizontal reverse function.
Rear Projection
AUDIENCE SIDE
90˚
90˚
Mirror
The projector lens should be centered
in the middle of the screen.
If the projector and screen are not
centered properly, the picture will be
distorted, making viewing difficult.
Example of a ceiling-mount setup
Before mounting the projector, be sure to contact your nearest Authorized Sharp Industrial LCD Products Dealer to
obtain the manufacturer recommended ceiling mount bracket (sold separately). (AN-XGCM40 Ceiling Mount
Bracket, AN-EP101AP Extension Tube for AN-XGCM40.)
TOP VIEW
SIDE VIEW
90˚
90˚
Lens center
Lens center
• If the relative positions of the projector and the screen are not properly adjusted, the picture will be distorted.
Note:
• A polarizing screen cannot be used with this projector.
E-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Height of the Picture
Use the adjuster release to adjust the angle of the projector and height of the picture. Minor adjustments can be
made with the adjusters.
Adjuster
release
Adjuster release
Adjusters
1
2
1. Press the adjuster release and lift the
projector to the desired angle with both
hands
• The adjuster legs will extend to the surface of the
table.
2. Remove your hand from the adjuster
release
• The adjuster legs will lock in position. Release the
projector once you are sure the adjuster legs
have locked in position.
3. Make any minor adjustments necessary
• Turn the adjusters to further adjust the angle of
the projector.
3
Returning the projector to its original position
• While holding the projector with both hands, press the
adjuster release and slowly lower the projector to its original
position.
Notes:
• Adjustable up to approximately 5° from the horizontal.
• When adjustments are made with the adjusters, the picture may
become distorted, depending on the relative positions of the
projector and the screen.
• After adjusting, in some cases, all of the adjuster legs may not be
resting on the table.
To prevent the projector from wobbling, adjust the adjuster legs so
that they firmly contact the table.
Cautions:
• Do not press the adjuster release when the adjuster legs are
extended without firmly holding the projector.
• When lowering the projector, be careful not to get your fingers caught
in the area between the adjusters and the projector.
• Do not hold the lens when lifting or lowering the projector.
Transporting the Projector
Use the carrying handle when carrying the projector.
When transporting the projector, carry it by the handle located on the
side of the unit.
Note:
Carrying handle
• Always put on the lens cap to prevent damage to the lens when transporting
the projector.
Caution:
• Do not lift or carry the projector by the lens or the lens cap as this may
damage the lens.
E-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector (VIDEO 1, VIDEO 2)
To playback audio and video with the projector connected to a VCR, Laser Disc Player or external audio amplifier,
make the following connections.
• Always turn off the LCD Projector while connecting to video equipment, in order to protect both the projector and the
equipment being connected.
Rear terminals
COMPUTER RGB
COMPUTER AUDIO
IN 1
IN 2
IN 1
IN 2
Used when the AV equipment
to be connected has an
AUDIO
OUTPUT
WIRED
REMOTE
OUT
S-VIDEO output terminal.
PC CONTROL
1
2
L
R
IN
1
OFF
ON
IN
2
S-VIDEO
VIDEO
L
R
AUDIO
110-120V/
200-240V~
Playback
Playback
To
audio
output
To
video
output
terminal
To
S-video
output
To
audio
output
To
audio
input
terminals
terminals
terminal
terminals
Video equipment
VCR
Amplifier
Select the audio you want to output by selecting VIDEO 1 or VIDEO 2.
Note the following when using the S-VIDEO INPUT terminal:
• The S-VIDEO INPUT terminal uses a video signal system in which the picture is separated into a color and a luminance signal
to realize a higher-quality picture.
• By using the external amplifier, the volume can be amplified for greater sound.
E-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector (RGB 1, 2: Computer)
• Please carefully read the manual of the computer you will be con-
necting.
• Before connecting, be sure to turn both the projector and the computer
off. After making all connections, turn the projector on first. The com-
puter should always be turned on last.
6-pin DIN
Personal computer
Mouse Control
Cable for IBM
PS/2 (Supplied)
4-pin DIN
Mouse Control
Cable for
Macintosh
Series
To display input terminal
15-pin D-Sub
Note:
• The arrows (←, ↔ ) indicate the
direction of the signals.
(Supplied)
To RS-232C
terminal
15-pin D-Sub
Rear terminals
RGB Signal Cable (Supplied)
RS-232C
cable (Cross
Type, sold
separetely)
COMPUTER RGB
COMPUTER AUDIO
IN 1
IN 2
IN 1
IN 2
Audio Cable for Personal Computer (Supplied)
AUDIO
OUTPUT
WIRED
REMOTE
OUT
9-pin D-Sub
Mouse Control Cable (Supplied)
PC CONTROL
1
2
L
R
IN
1
9-pin D-Sub
OFF
ON
IN
2
S-VIDEO
VIDEO
L
R
Computer Control Cable
(with mouse/RS-232C
input terminal) (Supplied)
Note:
AUDIO
110-120V/
200-240V~
• By using RGB INPUT 2 and PC CONTROL 2,
another computer can be connected to and
operated with the projector. The RS-232C func-
tion, however, will not operate when used with
the PC CONTROL 2 terminal.
COMPUTER CONTROL CABLE
RS-232C (D-sub 9-pin)
Use when controlling the projector from your personal computer.
(RS-232C does not function when connected to PC CONTROL 2.)
MOUSE TERMINAL
Use when operating your personal computer with the wireless mouse
remote control.
Left Terminal: D-sub 9-pin (for IBM/Mac)
Right Terminal: 9-pin mini DIN (for NEC in JAPAN)
• You can connect your projector to a computer for easy projection of full color computer images and an external monitor for
simultaneous viewing. See pages 16 and 17 for details of the connections.
• Refer to page 18 for a list of personal computers connectable to the projector. Use with computers other than those listed
may cause some of the functions not to work.
• When the RS-232C terminal on this unit is connected to a personal computer via an RS-232C cable (cross type) and the sup-
plied computer control cable, the personal computer can control the projector and the status of the projector can be
checked. See pages 34 and 35 for details.
• By connecting the supplied computer control cable to the PC CONTROL terminal on your projector and the supplied mouse
control cables to the mouse terminal on your personal computer, you can use the wireless mouse on the remote control,
instead of the mouse equipped with your personal computer, to operate your personal computer. Refer to page 8 for details.
Notes:
• The RS-232C function will only operate when the connection cable is connected to the PC CONTROL 1 terminal on the projector.
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set-up. Please refer to your computer owners
manual for details on setting-up/installing the correct mouse driver.
• Do not connect or remove the computer control cable, mouse control cables, or RS-232C cable to/from your computer while it is on. This may
damage your computer.
• Do not connect to the mouse input terminals on the computer control cable for IBM/Mac and PC98 simultaneously.
• Be sure to use the supplied computer control cable when connecting the PC CONTROL terminals.
“Plug and Play” Function
This projector is compatible with VESA DDC 1 and DDC 2B standards.
This projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy
set-up.
Note:
• The DDC, “Plug and Play” function of this projector is only functional when used in conjunction with a VESA DDC compatible computer.
E-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Computer RGB Input (RGB 1, 2)/Output Terminals
You can connect your projector to a computer for easy projection of full-color computer images, and an external
monitor for simultaneous viewing.
1
1. Connecting to an IBM-PC (VGA, SVGA,
Rear view of the projector
COMPUTER RGB
XGA) or a Macintosh Series computer
Plug one end of the RGB signal cable into the RGB
INPUT terminal on the projector and the other end
into the RGB signal output terminal on the
computer, and secure the plugs by tightening the
thumb screws.
IN 1
IN 2
RGB Signal
Input Socket
Notes:
• This connection is possible only when using a computer with a VGA/
SVGA/XGA or Mac display output port.
• By using RGB INPUT 2 and PC CONTROL 2, another computer can
be connected to and operated with the projector.
• For use with some Macintosh computers, a Macintosh/VGA adaptor
may be required. Contact your nearest Authorized Sharp Industrial
LCD Product Dealer or third-party manufacturer.
IBM-PC (VGA,
SVGA, XGA)
Series (computer)
ANALOG RGB OUT
RGB Signal
Cable
(Supplied)
RGB Signal
Output Socket
2. Connecting to other compatible
computers
When connecting the projector to a compatible computer
other than an IBM-PC (VGA/SVGA/XGA) or Macintosh
series, a separate cable may be needed. Please contact
your dealer for ordering information.
Notes:
• Connecting computers other than the recommended types may
result in damage to the projector, the computer, or both.
• Connect the audio from the computer to the COMPUTER AUDIO
INPUT terminal.
3. Connecting to the COMPUTER AUDIO
3
COMPUTER AUDIO
IN 2
IN 1
IN 2
INPUT
• The COMPUTER AUDIO INPUT 1 accepts audio from
the COMPUTER RGB 1 input, and the COMPUTER
AUDIO INPUT 2 accepts audio from the COMPUTER
RGB 2 input.
AUDIO
OUTPUT
RED
REMOTE
• Connect a 3.5 mm Stereo Minijack cable from the
audio output terminal on the computer to the
COMPUTER AUDIO INPUT terminal on the projector.
PC CONTROL
1
2
E-16
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER RGB
IN 1
IN 2
4
4. Connecting an external monitor
Connect your computer monitor to the projector’s COM-
PUTER RGB OUTPUT terminal to view images simulta-
neously on the external monitor and the projection
screen. Select either RGB 1 or RGB 2 to output the
images to the monitor.
OUT
Optional Macintosh
adaptor cable
Direct
connection
U.S.A. ONLY
Caution (Apple Macintosh):
Do not connect the COMPUTER RGB OUTPUT to any moni-
tor except the following:
Apple Color RGB Monitor 13؆/14؆ (640
ן 480) or 16؆/17؆ (832
ן 624) or
The output signal from the projector to the monitor should be
the same as the input signal from the computer to the
projector.
External IBM-PC
monitor
External Macintosh
monitor
Example:
Input 13؆/14؆ (640
ן 480) → Output (640 ן 480) Input 16؆/17؆ (832
ן 624) → Output (832 ן 624) Notes:
• When using the projector with an external IBM-PC monitor, connect
the monitor using the supplied cable. When using the projector with a
Macintosh monitor, an optional adaptor cable is required. Before
using any other type of monitor, carefully check the monitor’s inter-
face specifications and make sure that they match the specifications
of the projector’s interface.
• The external monitor output will only display an analog computer
input signal. It will not display a digital or video input signal. To split
the composite video signal, use a video distribution amplifier. This is
available from your local dealer. The computer RGB output will only
loop through the same signal connected to the computer RGB input.
(VGA IN → VGA OUT, Mac IN → Mac OUT)
E-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Signals (Recommended Timing)
For Apple Macintosh Series
For IBM and compatibles
VIDEO SIGNAL
Input signals:
The video output signal timing of different types of
video signals are shown below for reference.
e
C-SYNC(H)
VIDEO SIGNAL
HORIZONTAL
SYNC SIGNAL
e = 2 dot
d
a
b
c
a
b
c
d
VIDEO SIGNAL
C-SYNC(V)
VIDEO SIGNAL
VERTICAL
SYNC SIGNAL
w
z
x
y
w
z
x
y
V-SYNC
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
Apple
Apple
Apple
MacintoshTM MacintoshTM
VGA
VESA
SVGA
Graphic
SVGA
VESA
SVGA
VESA
SVGA
VESA
XGA
XGA
XGA
MacintoshTM
IIsi
LC
VESA
VESA
VESA
MODE
Text
720 dots
Graphic
640 dots
Graphic
13" Monitor 13" Monitor 16" Monitor
Guideline Standard Standard Guideline Standard Standard
640 dots 800 dots 800 dots 800 dots 800 dots 1024 dots 1024 dots 1024 dots
640 dots
480 lines
640 dots
480 lines
832 dots
624 lines
350 lines 400 lines 350 lines 400 lines 480 lines 480 lines 600 lines 600 lines 600 lines 600 lines 768 lines 768 lines 768 lines
0.7Vp-p
0.7Vp-p
0.7Vp-p
0.7Vp-p
0.7Vp-p
0.7Vp-p
0.7Vp-p
0.7Vp-p
0.7Vp-p 1Vp-p max. 0.7Vp-p max. 0.7Vp-p max.
LEVEL
TYPE
75Ω load
75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load 75Ω load
75Ω load
75Ω load
VIDEO
R • G • B
R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B R • G • B
C.SYNC
R • G • B
C.SYNC
R • G • B
C.SYNC
R • G • B
FRONT PORCH
a
dot
17
14
24
24
40
56
16
24
24
16
64
78
31
SYNC
b
c
d
dot
dot
dot
dot
µs
108
55
96
50
40
128
72
128
88
120
64
80
160
136
160
136
144
96
176
64
96
62
116
65
224
BACK PORCH
128
VIDEO PERIOD
H
720
640
640
800
800
800
800
1,024
1,344
20.677
15,385
48,363
65.000
TTL
1,024
1,328
17.707
13.3
1,024
1,312
16.660
12.7
640
640
832
900
800
832
1,024
28.444
27.777
35.156
36.000
TTL
1,056
26.400
25.000
37.879
40.000
TTL
1,040
20.800
20.000
48.077
50.000
TTL
1,056
21.333
20.202
46.875
49.500
TTL
864
896
1,152
20.124
17.468
49.693
57.246
TTL
S
Y
N
C
1H (a+b+c+d)
31.7774
35.3082
31.4689
28.322
31.7776
39.7219
31.4688
25.175
TTL
26.413
31.746
37.860
31.500
TTL
28.5714
33.0688
35.0000
30.2400
TTL
28.595
31.914063
34.971149
31.334149
TTL
1 dot
1/H
ns
kHz
MHz
56.476
75.0
60.023
78.75
TTL
1/dot
LEVEL
TTL
TTL
–
TTL
SYNC POLARITY
+/–
H
+
+
–
–
–
+/–
+
+
+
–
–
+
–
–
–
FRONT PORCH
w
38
13
38
13
11
9
1
1
37
1
3
3
1
3
3
1
SYNC
x
y
z
H
H
2
2
2
2
2
3
28
2
22
4
23
6
23
3
21
6
29
6
29
3
28
3
3
3
39
BACK PORCH
VIDEO PERIOD
59
34
59
34
32
39
39
V
S
Y
N
C
H
350
449
400
449
350
449
400
449
480
525
480
600
600
600
600
768
768
768
480
525
15.00
66.67
TTL
–
480
525
15.00
66.67
TTL
–
624
H
520
625
628
666
625
806
806
800
667
1V (w+x+y+z)
ms
Hz
14.2681 14.2681 14.2681 14.2681 16.6832
70.0866 70.0866 70.0863 70.0863 59.9405
13.735
72.809
TTL
–
17.778
56.250
TTL
+/–
16.579
60.317
TTL
+
13.853
72.188
TTL
+
13.333
75.000
TTL
+
16.666
60.006
TTL
–
14.272
70.069
TTL
–
13.328
75.029
TTL
+
13.423
74.502
TTL
–
1/v
LEVEL
TTL
–
TTL
+
TTL
–
TTL
+
TTL
–
SYNC POLARITY
+/–
Notes:
• When connecting a notebook computer to the data-projector for display on an (800
ן 600) LCD screen, the screen may not show a full picture image. See page 20, “Computer Mode Memory Adjustments” for details.
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. If this
occurs, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on
how to change display modes can be found in your notebook computer’s operation manual.
E-18
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB Adjustment Controls
When displaying computer patterns which repeat every other dot (tiling, vertical stripes, etc.), interference may
occur between the LCD pixels, causing flickering, vertical stripes, or contrast irregularities in portions of the
screen. Should this occur, use the ADJUSTMENT ß/© buttons for HORIZONTAL (LEFT/RIGHT) and VERTICAL
(UP/DOWN) position adjustments to adjust for the optimum picture.
RGB Input Adjustments (“CLOCK”, “PHASE”, “V-POS”
and “H-POS”)
1. Select the input of the image you want to adjust (RGB 1 or
2) with the INPUT SELECT button and press the MENU
button then select the RGB INPUT ADJ. mode.
With the MENU screen displayed, press the ADJUSTMENT ƒ/∂ buttons
to select “RGB 1 INPUT ADJ.” Then press the ENTER button to display the
“RGB 1 INPUT ADJ.” screen.
On-Screen Display
2
2. Select the item you wish to adjust with the ADJUST-
MENT ƒ/∂ buttons. Adjust the item with the ADJUST-
MENT ß/© buttons.
R G B 1 I N P U T A D J .
C L O C K
P H A S E
H - P O S
V - P O S
0
0
0
0
-
-
-
-
+
+
+
+
[
]
M O D E
O F F
R E S E T
M E M O R Y S E L E C T
Note:
• To display only the item that you want to adjust, press the ENTER button after selecting the item
with the ADJUSTMENT ƒ/∂ buttons. Then adjust the item with the ADJUSTMENT ß/© buttons.
: S E L .
: A D J .
ENTER
MENU
: N E X T
: E N D
3. Press the MENU button anytime to exit RGB INPUT ADJ.
Description of Adjustment Items
CLOCK SPEED ADJUSTMENT (FAST/SLOW)
• Adjust the input signal horizontal frequency and the dot clock so that the screen
display is normal.
PHASE ADJUSTMENT (UP/DOWN)
• Used to reduce image distortion or improve contrast.
HORIZONTAL POSITION ADJUSTMENT (LEFT/RIGHT)
• Used to center the on-screen image by moving it to the left or right.
VERTICAL POSITION ADJUSTMENT (UP/DOWN)
• Used to center the on-screen image by moving it up or down.
MODE ADJUSTMENT
CONNECTING TO IBM-PC COMPUTERS
• Ordinarily, the type of input signal is detected and the correct resolution mode
(Text or Graphics) is automatically selected. However, for the following signals,
set “MODE” to “ON” or “OFF” to select the projector’s resolution mode to match
the computer display mode properly.
720 dots
ן 400 lines, 720 dots ן 350 lines (Text Mode) 640 dots
ן 400 lines, 640 dots ן 350 lines (Graphic Mode) • For graphic mode, select “MODE” and set the “MODE” to “ON”.
• For text mode, select “MODE” again at this time, and set “MODE” to “OFF”.
CONNECTING TO MACINTOSH LC/II SERIES COMPUTERS
• When connecting to a Macintosh II with 35 kHz Dot Frequency, select “MODE”
and set “MODE” to “ON”.
• When connecting to a Macintosh LC Series computer with 34.97 kHz Dot Fre-
quency, set “MODE” to “OFF”.
• When connecting to third party video cards and other Macintosh computers, set
“MODE” to “ON” or “OFF” to select the correct display mode.
• When the input signal is automatically detected or when there is no input signal,
“MODE (---)” appears on the screen and the display mode cannot be changed.
INITIAL RESET
• To return the “H-POS”, “V-POS”, “PHASE” and “CLOCK” adjustments to their
initial settings, select “RESET” and then press the ENTER button.
MEMORY SELECT
• Used to store up to seven computer mode adjustments.
Note:
• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering
may occur, making the picture hard to see.)
E-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Mode Memory Adjustments
• The projector has been preset with different modes for
use with SVGA and other compatible computers.
However, 7 memory positions are provided to store
mode adjustments.
• Each memory position can be used to store mode
adjustments to match the computer.
1 When RGB 1 or 2 is selected.
1. Press the ENTER button to select the
Memory Adjustment mode
On-Screen Display
• Press the MENU button. While the MENU screen
is displayed, press the ADJUSTMENT ƒ/∂ but-
tons to select “RGB1 INPUT ADJ.” Press the
ENTER button. The MENU mode changes as
shown.
R G B 1 I N P U T A D J .
C L O C K
P H A S E
H - P O S
V - P O S
M O D E
R E S E T
M E M O R Y S E L E C T
0
0
0
0
-
-
-
-
+
+
+
+
R G B 1 A D J .
R G B 1 I N P U T A D J .
I M A G E A D J .
A U D I O
S Y S T E M S E T U P
L A N G U A G E
[
]
O F F
• While the RGB INPUT adjustment menu is dis-
played, press the ADJUSTMENT ƒ/∂ buttons to
select “MEMORY SELECT”. Then press the
ENTER button to change the image.
: S E L .
ENTER
MENU
: N E X T
: E N D
: S E L .
ENTER
MENU
: N E X T
: E N D
2
2. Press the ADJUSTMENT ß/© buttons
• The screen shown on the left will appear. There
are 7 memory positions.
ME MOR Y SE L E C T
ME MOR Y SE L E C T
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
• Press the ADJUSTMENT ƒ button once to move
to the following screen. Press the ADJUSTMENT
ß/© buttons to select the number of the memory
you want to adjust. If that memory position has
not been set, the screen on the right will be dis-
played. If it has been set, the screen on the left
will be displayed. MEMORY No.0 cannot be set. It
contains the fixed factory preset settings.
• To make or change a setting, press the ADJUST-
MENT ƒ/∂ buttons to move the cursor to “SET-
TING.” Then press the ENTER button to go to the
RGB INPUT adjustment menu screen. (If you do
not want to make any adjustments, press the
MENU button.)
S T A N D A R D S E T T I N G
S E T T I N G
S T A N D A R D S E T T I N G
S E T T I N G
: S E L .
: A D J .
ENTER
MENU
: E N T E R
: E N D
: S E L .
ENTER
MENU
: B A C K
: E N D
ME MOR Y SE L E C T
ME MOR Y SE L E C T
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
N O N
R E S O L U T I O N
H O R F R E Q
V E R T F R E Q
S E T T I N G
1 0 2 4 ×7 6 8
6 0 . 0 KHz
7 5 Hz
S E T T I N G
• Select the item you want to adjust by pressing the
ADJUSTMENT ƒ/∂ buttons, then use the AD-
JUSTMENT ß/© buttons to make the adjust-
ments. When adjustments are completed, press
the MENU button. The display disappears and
the adjustments are stored in memory as a user
mode. See page 19 for details on the adjustment
items.
: S E L .
: A D J .
ENTER
: E N T E R
: S E L .
: A D J .
ENTER
: E N T E R
: E N D
MENU
: E N D
MENU
3. Press the MENU button anytime to exit
RGB INPUT ADJ.
E-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation of the Projector
OFF
ON
1
1. Connect the AC cord
Connect the supplied AC cord to the AC inlet on
the back of the projector .
110-120V/
200-240V~
1 AC cord
2
2. Turn on the MAIN POWER
POWER
LAMP
TEMP.
OFF
ON
Press the MAIN POWER switch on the back of the
projector. The POWER indicator lights red and the
projector enters STANDBY mode.
When the MAIN
POWER is on, the
POWER indicator
lights red.
Projector
ON/OFF
Remote control
3
3. Turn on the POWER
ON/OFF
Press the POWER ON/OFF button on the projector
or the POWER ON button on the remote control.
• When the power is turned off by pressing the POWER
ON/OFF button, the POWER indicator will not turn off
until the fan has stopped running.
ON
• See page 30, “Lamp/Maintenance Indicators” for
details.
OFF
Notes:
• When the POWER indicator is not lit, the remote control cannot be
used to operate the projector.
• If the power is turned on immediately after it has been turned off, it
may take a short while before the lamp turns on. (During this period
the LAMP REPLACEMENT indicator flashes.)
POWER
LAMP
TEMP.
• After the projector is unpacked and turned on for the first time, a
slight odor may be emitted from the exhaust fan. This odor will soon
disappear with use.
When the power is on, the LAMP
REPLACEMENT indicator flashes
to show the operating condition of
the lamp.
Caution:
• Be sure to take off the lens cap before operation of the projector. Do
not place the lens cap on the lens during operation. The lens cap
may become extremely hot.
Green: Lamp is ready
Flashing green: Warming up
Red: Change bulb
E-21
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display
4
4. Select one of eight ON-SCREEN
DISPLAY languages
L A N G U A G E
You can return to the previous screen by se-
lecting the uppermost item (turquoise) with the
ADJUSTMENT ƒ/∂ buttons (in this case, “LAN-
GUAGE”) and then pressing the ENTER button.
E N G L I S H
D E U T S C H
E S P A Ñ O L
N E D E R L A N D S
F R A N Ç A I S
I T A L I A N O
S V E N S K A
The on-screen display is set to English at the fac-
tory. The language for the unit’s ON-SCREEN DIS-
PLAY can be set to English, German, Spanish,
Dutch, French, Italian, Swedish or Japanese.
ENTER
MENU
: S E L .
: E N T E R
: E N D
Setting the ON-SCREEN DISPLAY language
1. Press the MENU button. The menu will appear on
the screen.
2. Press the ADJUSTMENT ƒ/∂ buttons to highlight
the “LANGUAGE” item yellow. Then press the
ENTER button to display the language menu.
3. Press the ADJUSTMENT ƒ/∂ buttons to highlight
the desired language yellow. Then press the ENTER
button to set the language. The ON-SCREEN DIS-
PLAY is now programmed to display in the language
chosen.
5
5. Change the system mode
The video input system mode is set to “AUTO” at
the factory, but it can be changed to a different
mode if the selected system mode is not compati-
ble with the connected audiovisual equipment
(when a color image appears in black and white,
etc.).
S Y S T E M
I M A G E A D J .
[
[
[
]
O N
A U T O
P A L
S E C A M
N T S C 4 . 4 3
N T S C 3 . 5 8
B L U E S C R E E N
B L K S C R N D I S P
I N P U T D I S P L A Y
S Y S T E M
]
]
O F F
O F F
[
[
]
]
R E V E R S E
O F F
O F F
➞
I N V E R T
: S E L .
ENTER
MENU
: E N T E R
: E N D
: S E L .
ENTER
: N E X T
: E N D
1. Press the MENU button. The menu will appear on
the screen.
MENU
2. Press the ADJUSTMENT ƒ/∂ buttons to highlight
the “IMAGE ADJ.” yellow. Then press the ENTER
button to display the “IMAGE ADJ.”
3. Press the ADJUSTMENT ƒ/∂ buttons to highlight
“SYSTEM” yellow. Then press the ENTER button to
display the “SYSTEM”.
4. Press the ADJUSTMENT ƒ/∂ buttons to highlight
yellow the video system desired yellow. Then press
the ENTER button to set the system.
Notes:
• In AUTO mode, “PAL,” “SECAM”, “NTSC 4.43” or “NTSC 3.58” is
displayed on the screen for a few seconds when the mode is
changed with the INPUT SELECT button.
• When the system mode is set to “AUTO”, you may not receive a clear
picture due to signal differences. If this happens, switch to the color
system you are viewing.
E-22
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display
6
6. Select input
For viewing the picture from a
video source connected to:
VIDEO INPUT 1
Press the INPUT SELECT button on the projector to
switch the picture input. When you press the but-
ton, the current input mode is displayed for about 4
seconds. If you press the button again while the
input mode is displayed, the mode changes as
shown on the left.
VIDEO INPUT 2
Confirm the selected input terminal and press the
INPUT SELECT button.
COMPUTER RGB1
COMPUTER RGB2
Notes:
• The input can be selected directly using the VIDEO 1, VIDEO 2,
DATA 1 and DATA 2 buttons on the remote control. (When DATA 1 or
DATA 2 is selected, the RGB 1 or RGB 2 screen will appear
accordingly.)
• In VIDEO mode, the system being received will be indicated below
the “VIDEO” display.
• When selecting RGB mode, the resolution being displayed will be
indicated under “RGB,” as shown on the left. (Refer to the second
example when connecting to Mac display.)
• When no signals are being received, “NO SIGNAL” will be displayed.
When receiving a signal the projector is not preset to receive, “NOT
REG.” will be displayed. (This display function does not operate in
Video mode.)
Mac
• The picture size differs in RGB, NTSC, PAL and SECAM INPUT
modes.
7
7. Press INPUT CHECK
When the INPUT CHECK button on the remote con-
trol is pressed, the current input mode is displayed
for about 4 seconds.
Note:
• The INPUT CHECK button will not function if the “INPUT DISPLAY” is
turned off, as described on page 28.
Mac
8
9
8. Adjust the volume
The number of displayed segments
(0–60) increases or decreases as the
volume is raised or lowered.
Press the VOLUME UP-DOWN buttons on the pro-
jector or on the remote control to adjust the volume.
MUTE
• Press the MUTE button to temporarily turn off the
sound.
• Press the MUTE button once again to turn the
sound back on.
V O L U M E
3 8
9. To turn off the power from the projector
or the remote control
• Press the POWER ON/OFF button on either the
projector or the remote control. The screen on the left
will appear.
• If you want to turn off the power, press the POWER ON/
OFF button on either the projector or the remote control
again within 4 seconds. The power is now temporarily
turned off.
T U R N
P O W E R
O
G
F
A
I
F
I
?
Y E
N O
S
:
:
P
L
R
E
E
A
S
S
S
A
N
P
E
W A
T
• If you accidentally pressed the POWER ON/OFF button
and do not want to turn off the power, wait until the
On-Screen Display disappears.
The POWER indicator will turn red and the cooling fan
will run for 90 seconds, then the power will turn off,
and the projector will return to STANDBY mode.
POWER
LAMP
TEMP.
The power can be turned on again either from the
projector or remote control. When the power is turned
on, the POWER indicator and LAMP REPLACEMENT
indicator light green.
Note:
• When the MAIN POWER is off on the projector set, the power cannot
be turned on from the remote control.
E-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture
• This projector’s picture is factory preset to standard
settings. However, you can adjust it to suit your own
preferences with the ADJUSTMENT buttons on the
projector and the remote control.
• The adjustments can be memorized in RGB 1, RGB 2,
VIDEO 1 or VIDEO 2 separately.
• Four picture modes can be adjusted: “PICTURE,”
“BRIGHT,” “RED,” and “BLUE.”
Adjusting the Picture
On-Screen Display
1
1. Use the MENU button to select the mode
to be adjusted
R G B 1 A D J .
• When the MENU button is pressed, the MENU
mode is indicated for about 30 seconds. Press
the ADJUSTMENT ƒ/∂ buttons to select “RGB 1
ADJ.”, then press the ENTER button.
R G B 1 I N P U T A D J .
I M A G E A D J .
A U D I O
S Y S T E M S E T U P
L A N G U A G E
ENTER
MENU
: S E L .
: N E X T
: E N D
2
2. Adjust the Picture
R G B 1 A D J .
• Press the ADJUSTMENT ƒ/∂ buttons to high-
light yellow the picture adjustment item you want
to adjust.
0
P I C T U R E
B R I G H T
R E D
B L U E
R E S E T
-
+
+
+
+
0
0
0
-
-
-
• Press the ADJUSTMENT ß/© buttons to move
the “ ” mark of the selected adjustment item to
the desired setting.
• The adjustment mode is displayed for about
30 seconds.
ENTER
MENU
: S E L .
: A D J .
: N E X T
: E N D
Description of Adjustment Items
Selected item ADJUSTMENT ß button ADJUSTMENT © button
PICTURE
BRIGHT
RED
For less contrast
For less brightness
For weaker red
For more contrast
For more brightness
For stronger red
BLUE
COLOR
TINT
For weaker blue
For less color intensity
Skin tones become
purplish
For stronger blue
For more color intensity
Skin tones become
greenish
SHARPNESS For less sharpness
For more sharpness
All RGB Video Adjustment items are returned to the
factory preset settings.
RESET
Note: To reset all adjustment items, select “RESET” in
“RGB 1 ADJ.” mode and press the ENTER button.
3
3. Display only the item to adjust
• Press the ADJUSTMENT ƒ/∂ buttons to high-
light yellow the picture adjustment item you want
to adjust. If you press the ENTER button at this
time, only the selected item will be displayed.
• Press the ADJUSTMENT ß/© buttons to move
the “ ” mark of the selected adjustment item to
the desired setting.
P I C T U R E
0
-
+
ENTER
MENU
: S E L .
: A D J .
: E N T E R
: E N D
• The adjustment mode is displayed for about 30
seconds.
Notes:
• When a VIDEO signal input has been selected, only “PICTURE,”
“BRIGHT,” “COLOR,” “TINT” and “SHARPNESS” can be adjusted.
• TINT only appears in NTSC 3.58 mode.
4. Press the MENU button anytime to exit
RGB ADJ.
E-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Audio
• The projector’s audio is factory preset to the standard
setting. However, you can adjust it to suit your own
preference with the ADJUSTMENT buttons on the
projector or the remote control.
• You can adjust the “BALANCE”, “TREBLE” and “BASS”.
• To return to the factory preset mode, press the AD-
JUSTMENT ƒ/∂ buttons to select “RESET”, then
press the ENTER button.
• Press the MENU button to select the normal screen
mode.
On-Screen Display
Adjusting the Audio
A U D I O
• Press the MENU button.
0
0
0
B A L A N C E
T R E B L E
B A S S
L
-
-
R
+
+
Select “AUDIO” with the ADJUSTMENT ƒ/∂ buttons.
Then press the ENTER button to change to the picture
indicated on the left.
R E S E T
• Select “BALANCE,” “TREBLE” or “BASS” with the AD-
JUSTMENT ƒ/∂ buttons. Adjust the mode you want
with the ADJUSTMENT ß/© buttons.
: S E L .
: A D J .
MENU
: E N D
• To return to the factory preset mode, press the AD-
JUSTMENT ƒ/∂ buttons to select “RESET”, then press
the ENTER button.
Description of Adjustment Items
Selected
items
ADJUSTMENT ß
button
ADJUSTMENT ©
button
BALANCE
Increased audio from the Increased audio from the
left speaker
Weaker treble
Weaker bass
right speaker
Stronger treble
Stronger bass
TREBLE
BASS
E-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Functions on the Projector
Setting Up the System
Using this function, you can check the input signal and
lamp usage time, and select the remote mouse.
On-Screen Display
Checking the system and lamp usage time
• Press the MENU button. Select “SYSTEM SETUP” with the
ADJUSTMENT ƒ/∂ buttons. Then press the ENTER button to
change to the picture indicated on the left.
• The current system conditions, including the lamp usage
time, will be displayed on the screen.
S Y S T E M S E T U P
R E S O L U T I O N
H O R F R E Q
V E R T F R E Q
L A M P U S A G E
R E M O T E M O U S E
8 0 0 @ 6 0 0
3 7 . 9 KHz
6 0 Hz
1 2 3 4 H
[
]
A T
• Press the MENU button to select the normal screen mode.
: S E L .
Note:
MENU
: A D J .
: E N D
• In the video screen, the resolution and frequency settings will not be
displayed.
Selecting the Remote Mouse
S Y S T E M S E T U P
• Separate settings can be selected for RGB 1 and RGB 2.
• Use the INPUT SELECT buttons to select DATA 1 (RGB 1) or
DATA 2 (RGB 2).
R E S O L U T I O N
H O R F R E Q
V E R T F R E Q
L A M P U S A G E
R E M O T E M O U S E
8 0 0 @ 6 0 0
3 7 . 9 KHz
6 0 Hz
• Press the MENU button.
• Select “SYSTEM SETUP” with the ADJUSTMENT ƒ/∂
buttons. Then press the ENTER button.
1 2 3 4 H
[
]
A T
• Select “REMOTE MOUSE” and then select either “[AT]” or
“[98] ”with the ADJUSTMENT ß/© buttons.
• Select “[AT]” when using IBM compatibles and Apple
Macintosh series.
: S E L .
MENU
: A D J .
: E N D
• Select “[98]” when using NEC PC98 series (for Japan).
• Press the MENU button to select the normal screen mode.
Background level
• The Background Level adjustment can be used to adjust the
picture white balance for the selected Video Input Source.
• Optimal image quality can be achieved by adjusting the
white portion of the picture to obtain the best color for the
selected source.
V I D E O 1 A D J .
B A C K G R N D L V L
I M A G E A D J .
A U D I O
S Y S T E M S E T U P
L A N G U A G E
ENTER
MENU
: S E L .
: N E X T
: E N D
Adjusting the BACKGROUND LEVEL
• Press the MENU button.
B A C K G R N D L V L
Select “BACKGRND LVL” with the ADJUSTMENT ƒ/∂
buttons. Then press the ENTER button to change the picture
as indicated on the left.
R E D
B L U E
R E S E T
0
0
-
-
+
+
• Select “RED” or “BLUE” with the ADJUSTMENT ƒ/∂ buttons.
Adjust the mode you want with the ADJUSTMENT ß/©
buttons.
• To return to the factory preset mode, press the ADJUSTMENT
ƒ/∂ buttons to select “RESET” then press the ENTER button.
• Press the MENU button to select the normal screen mode.
ENTER
MENU
: S E L .
: A D J .
: N E X T
: E N D
Note:
• To display only the item that you want to adjust, press the ENTER
button after selecting the item with the ADJUSTMENT ƒ/∂ buttons.
Then adjust the item with the ADJUSTMENT ß/© buttons.
E-26
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Projector
Using the Black Screen Function
This projector is equipped with a Black Screen Function.
This function can be used to black out the presentation
image.
• Press the BLACK SCREEN button on the projector or the
remote control to display the black screen. Press the BLACK
SCREEN button again to return to the presentation image.
Note:
• When “BLK SCRN DISP” is set to “OFF”, the On-Screen Display
(“BLACK SCREEN”) will not appear during black screen. See below.
BLACK SCREEN
On-Screen Display
Black Screen On-Screen Display override
The On-Screen Display (“BLACK SCREEN”) that appears
during black screen can be turned off. When “BLK SCRN
DISP” is set to “OFF”, the On-Screen Display will not
appear during black screen.
I M A G E A D J .
[
[
[
[
]
O N
B L K S C R N D I S P
I N P U T D I S P L A Y
R E V E R S E
]
]
]
O F F
O F F
O F F
I N V E R T
• Press the MENU button. While the MENU screen is displayed,
press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE
ADJ.”. Then press the ENTER button to display the “IMAGE
ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-
tons to select “BLK SCRN DISP” and press the ADJUST-
MENT ß/© buttons to select “ON” or “OFF”.
: S E L .
MENU
: A D J .
: E N D
E-27
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display
Using the Blue Screen Function
This projector is equipped with a Blue Screen function
that will turn the screen blue when the video input termi-
nal is not connected to anything, or the video component
is turned off.
I M A G E A D J .
[
[
[
]
B L U E S C R E E N
B L K S C R N D I S P
I N P U T D I S P L A Y
S Y S T E M
O N
]
]
O F F
O F F
[
[
]
]
• Press the MENU button. While the MENU screen is displayed,
press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE
ADJ.”. Then press the ENTER button to display the “IMAGE
ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-
tons to select “BLUE SCREEN,” and press the ADJUST-
MENT ß/© buttons to select “ON” or “OFF”. Press the MENU
button to return to the normal screen.
R E V E R S E
O F F
O F F
I N V E R T
: S E L .
MENU
: A D J .
: E N D
• When the Blue Screen function is on, the screen will turn blue
when no video signal is being input through the video input
terminal.
• When the Blue Screen function is on, and no video signal is
input via the input terminal for more than 15 minutes, the
power is automatically turned off.
• The indicators appear as shown each minute before the
power is turned off, from 5 minutes before until 1 minute
before.
REMAIN 5M
REMAIN 4M
Notes:
• The Blue Screen Function does not operate in RGB mode.
• When the power is turned off, the POWER indicator will light red.
• To turn the power on again, press the POWER button to set it to OFF,
then press it again to set it to ON.
REMAIN 1M
Using the Input Mode On-Screen Display
I M A G E A D J .
Override Function
[
[
[
[
]
]
]
]
O F F
O F F
O F F
O F F
B L K S C R N D I S P
I N P U T D I S P L A Y
R E V E R S E
The On-Screen Displays that appear during input select
(“RGB 1,024
ן 768, 75 Hz,” etc.) can be turned off. Once “INPUT DISPLAY” is turned off, the On-Screen Dis-
plays will not appear even if the INPUT CHECK button on
the remote control is pressed.
I N V E R T
: S E L .
MENU
: A D J .
: E N D
• Press the MENU button. While the MENU screen is displayed,
press the ADJUSTMENT ƒ/∂ buttons to select “IMAGE
ADJ.”. Then press the ENTER button to display the “IMAGE
ADJ.” screen as shown. Press the ADJUSTMENT ƒ/∂ but-
tons to select “INPUT DISPLAY”, and press ADJUST-
MENT ß/© buttons to select “ON” or “OFF”.
• When “OFF” is selected, the On-Screen Display (“RGB
1,024
ן 768, 75 Hz,” etc.) will not be displayed during input select.
E-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Filter Maintenance
• The air filter should be cleaned every 100 hours of use. Clean the filter more
Bottom Air Filter
often when the projector is used in a dusty or smoky location.
• Have your nearest Authorized Sharp Industrial LCD Products Dealer or Ser-
vice Center exchange the filter (PFILD0080CEZZ) when it is no longer pos-
sible to clean it.
AIR FILTER cover
Cleaning and Replacing the Filter
Turn OFF
the MAIN POWER.
Remove
the FILTER COVER.
Remove
the AIR FILTER.
1
2
3
Press the tab in the direction of
the arrow and lift open the filter
cover.
Grasp the air filter between your
fingers and lift it out of the filter
cover.
OFF
ON
POWER indicator goes off.
Unplug the power cord.
Tab
Press
Open
Replace
the FILTER COVER.
Clean the AIR FILTER.
Replace the AIR FILTER.
4
5
6
Clean the dust off the air filter
and cover with a vacuum
cleaner extension hose.
Place the filter underneath the
tabs on the filter frame.
Return the air filter to its original
position in the filter cover
opening.
Insert the tab on the end of the
filter cover into the filter cover
opening and press the filter
cover into position.
Note:
• Be sure the AIR FILTER COVER is securely installed. The power cannot be turned on unless it is correctly installed.
E-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp/Maintenance Indicators
Lamp
The lamp operating life differs, depending on the usage environment. It is recommended that the lamp be
replaced after 2,000 cumulative hours of use.
• When the lamp is nearing the end of its operating life, the picture and color quality will deteriorate. At this point, replace the
lamp. (See pages 31 and 32.)
Note: The lamp usage time can be checked with the On-Screen display. (See page 26.)
• If the new lamp does not light after replacement, take your projector to the nearest Authorized Sharp Industrial LCD Products
Dealer or Service Center for repair.
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
• The warning lights on the projector indicate problems inside the
projector.
Maintenance Indicators
• There are two warning lights: a TEMPERATURE indicator which warns
POWER
LAMP
TEMP.
that the projector is too hot, and a LAMP REPLACEMENT indicator which
lets you know when to change the lamp.
• If a problem occurs, either the TEMPERATURE indicator or the LAMP
REPLACEMENT indicator will light up red, and the power will shut off.
After turning off the power, follow the procedures given below.
LAMP REPLACEMENT TEMPERATURE
indicator indicator
Warning Indicator
Symptom
Problem
• Blocked air intake.
• Clogged air filter.
Possible Solution
• Relocate projector to a proper location.
TEMPERATURE
indicator
The internal
temperature is
abnormally high.
• Clean the filter.
(See page 29.)
• Cooling fan breakdown.
• Internal circuit failure.
• Take the projector to your nearest Autho-
rized Sharp Industrial LCD Products Dealer
or Service Center for repair.
• Burnt-out lamp.
• Carefully replace the lamp.
The lamp does not
light up.
LAMP REPLACE-
MENT indicator
• Take the projector to your nearest Autho-
rized Sharp Industrial LCD Products Dealer
or Service Center for repair.
• Lamp circuit failure.
Notes:
• If the TEMPERATURE indicator comes on, follow the above possible solutions and then wait until the projector has cooled down completely
before turning the power back on. (At least 5 minutes.)
• When the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be triggered, pre-
venting the power from going on. When this happens, take the power plug out of the AC outlet and put it back in again.
Before Calling for Service
Problem
Check
No picture and no sound.
• The projector AC cord is not plugged into the AC wall outlet.
• The main power switch is not pressed.
• The input is wrong. (See pages 22 and 23.)
• Cables improperly connected to rear panel of the projector. (See pages 14, 15, 16 and 17.)
• Remote control batteries have run down. (See page 7.)
• The optional cable for the remote control is improperly inserted.
• The main power of the remote control is not turned on.
• The remote control’s MOUSE/ADJUSTMENT switch is set to MOUSE.
Sound is heard but no picture
appears.
• Cables improperly connected to rear panel of the projector. (See pages 14, 15, 16 and 17.)
• The PICTURE and BRIGHT adjustments are set to minimum position. (See page 24.)
• On-Screen Display (“BLACK SCREEN”) is turned off and Black Screen function is turned on, creating a
black image. (See page 27.)
Color is faded or poor.
Picture is blurred.
• The COLOR and TINT adjustments are not correct. (See page 24.)
• Adjust the focus. (See page 9.)
• The projection distance is too long or too short to allow for proper focus. (See page 10.)
Picture appears but no sound is
heard.
• Cables improperly connected to rear panel of the projector. (See pages 14, 15, 16 and 17.)
• Volume is set to minimum. (See page 23.)
An unusual sound is occasionally • If the picture is normal, the sound is due to cabinet shrinkage caused by temperature changes. This
heard from the cabinet.
will not affect operation or performance.
Maintenance indicator lights up.
• Refer to “Lamp/Maintenance Indicators” on page 30.
E-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp Replacement
The lamp in the projector has a finite service life. The lamp operating life differs, depending on the usage
environment. It is recommended that the lamp be replaced after 2,000 cumulative hours of use. The lamp usage
time can be checked at the On-Screen display. (See page 26.)
• Replace the lamp when the picture starts becoming dark and the color contrast deteriorates.
Purchase a replacement UHP lamp unit (lamp/cage module) of the current type BQC-XGNV6XU/1 from your
nearest Authorized Sharp Industrial LCD Products Dealer. Then change the lamp by carefully following the
instructions below.
If you wish, you may bring the projector to your nearest Authorized Sharp Industrial LCD Products Dealer.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through an Authorized Sharp Industrial
LCD Products Dealer or Service Center. For the name of the nearest Authorized Sharp Industrial LCD Products
Dealer or Service Center, please call toll-free: 1-800-BE-SHARP (1-800-237-4277).
U.S.A. ONLY
How to Change the Lamp
Precaution:
• Take care not to touch either the glass surface of the lamp
cage or the inside of the projector with your bare hands.
(h)
(g)
(c)
(d)
(e)
(a)
(k)
(i)
(f)
(j)
(b)
Removing the lamp unit (see figure)
1. Press the power button (a) and turn the instrument off. After the cooling fan stops, turn off the MAIN POWER
switch (b). Remove the power cord from the AC outlet.
2. The lamp may be extremely hot. Wait at least an hour after the power cord is disconnected before carrying
out the following procedures.
3. Turn over the projector and unfasten the user service screw (d) that secures the lamp cage cover (c) as
shown in the above diagram. Then remove the lamp cage cover by pulling it in the direction of the arrow.
Note:
• When the lamp cage cover (c) has been removed, check that the surface of the lamp cage (i) has fully cooled before pro-
ceeding with step 4.
4. After the lamp cage (i) has sufficiently cooled, remove securing screws (e), (f) and (g) from the lamp cage.
5. Hold the lamp cage (i) by the handle (h) and pull it towards you.
E-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the lamp unit
1. Hold the lamp cage (i) by the handle (h) and press it in firmly while making sure that grooves on the side of
the lamp cage (j) are properly aligned with the projections inside the lamp cage compartment, and that the
holes on the top of the lamp cage (k) are aligned with the screw holes on the projector.
2. Tighten screws (e), (f), (g) and (d), then perform the above instructions in the reverse order.
Caution:
• Because some parts may not be sufficiently cooled, be sure to remove the lamp cage by the handle while taking care not
to touch the metallic areas.
Resetting the lamp timer
OFF
ON
1
1. Plug in the power cord.
110-120V/
200-240V~
2. While pressing the ADJUSTMENT ©,
ADJUSTMENT ƒ, and ENTER buttons on the
projector, turn on the MAIN POWER switch.
2
OFF
ON
After the projector turns on, “LAMP 0000H” is displayed,
indicating that the lamp timer is reset.
3
LAMP
0000
H
Note:
• Only reset the lamp timer after replacing the lamp.
E-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Pin Assignments
Analog RGB 1 and 2 Signal Input and Analog RGB Output Terminal: 15-pin mini
D-sub female connector
Computer Input
Analog
1. Video input (red)
2. Video input (green)
3. Video input (blue)
4. Reserve input 1
9. Not connected
10. GND
11. GND
1
5
10
15
12. Bi-directional data
6
5. Composite sync (Mac only) 13. Horizontal sync signal
11
6. Earth (red)
7. Earth (green)
8. Earth (blue)
14. Vertical sync signal
15. Data clock
Mouse Input Terminal (for IBM/Mac): 9-pin D-sub female connector
Pin No.
Signal
CD
RD
SD
Name
I/O
Input
Input
Output
Output
Reference
1
2
3
4
5
6
7
8
9
Carrier Detect
Receive Data
Send Data
Equipment Ready
Signal Ground
Data Set Ready
Request to Send
Clear to Send
Ring Indicator
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Connected to internal circuit
Connected to internal circuit
1
5
ER
SG
DR
RS
CS
CI
Output
Output
Input
9
6
Input
Mouse Input Terminal (for NEC PC98 series for Japan): 9-pin mini DIN connector
Pin No.
Signal
ם 5V XA
XB
YA
YB
LEFT
NC
RIGHT
GND
I/O
Reference
8
1
2
3
4
5
6
7
8
9
Input
Input
Input
Input
Input
Input
Input
Input
Computer output
Computer output
Computer output
Computer output
Computer output
Computer output
Not connected
Computer output
Computer output
7
9
6
3
5
4
2
1
RS-232C terminal: 9-pin D-sub male connector
Pin No.
Signal
CD
RD
SD
Name
I/O
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Not connected
1
2
3
4
5
6
7
8
9
Receive Data
Send Data
Input
Output
1
5
ER
SG
DR
RS
CS
CI
Signal Ground
Data Set Ready
Request to Send
Output
Output
6
9
E-33
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Terminal Specifications
1. PC control
A personal computer can be used to control the projector by connecting the supplied computer control
cable to the PC CONTROL 1 terminal on the projector and an RS-232C cable (cross type) (not supplied) to
the computer, and then connecting the RS-232C cable to the computer control cable.
(RS-232C does not function when connected to PC CONTROL 2. See page 15 for connection.)
2. Communication conditions
Set the serial port settings of the computer to match that of the table below.
Signal format:
Baud rate:
Data length:
Parity bit:
Conforms to RS-232C standard.
9,600 bps
8 bits
NON
1 bit
Stop bit:
Flow control:
None
3. Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the unit processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH)
Command 4-digits Parameter 4-digits
Response code format
Normal response
Return code (0DH)
Problem response (communication error or incorrect command)
Return code (0DH)
O
K
E
R
R
When more than one code is being sent, send each command only after the OK response code for the
previous command from the unit is verified.
Note:
• Using the computer control function of the unit, the liquid crystal projector conditions cannot be read to the computer. There-
fore, confirm the conditions by transmitting the display commands for each adjustment menu and checking the conditions
with the On-Screen Display. If the unit receives a command other than a menu display command, it will execute the command
without displaying the On-Screen Display.
COMMAND
PARAMETER
CONTROL ITEM
CONTROL CONTENTS
POWER OFF
4. Commands
C1 C2 C3 C4 P1 P2 P3 P4
P
P
I
O
O
V
V
R
R
C
E
W
W
E
R
R
D
D
B
B
K
A
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
0
1
1
2
1
2
0
1
2
3
4
5
6
7
8
1
2
3
4
5
*
POWER SETTING
POWER ON
VIDEO 1
I
E
VIDEO 2
INPUT SWITCHING
INPUT CHECK
I
G
G
H
L
RGB 1
Note:
I
RGB 2
• If a dash appears in the parameter
column enter a space. If an asterisk
appears enter a value in the range
indicated in brackets under CON-
TROL CONTENTS. See the examples
on the next page.
I
INPUT CHECK
ENGLISH
DEUTSCH
ESPANOL
M
M
E
L
A
M
M
E
E
L
L
A
A
NEDERLANDS
FRANCAIS
LANGUAGE
SELECTION
M
M
M
M
M
E
E
E
E
E
L
L
L
L
S
A
A
A
A
Y
ITALIANO
SVENSKA
JAPANESE
AUTO
PAL
M
M
M
M
V
V
V
V
V
V
E
E
E
E
A
A
A
A
A
A
S
S
S
S
P
B
C
T
Y
Y
Y
Y
I
VIDEO
SYSTEM
SELECTION
SECAM
NTSC 4.43
NTSC 3.58
PICTURE (
30 – 30) BRIGHT (
30 – 30) COLOR (
30 – 30) TINT (
30 – 30) SHARPNESS (
30 – 30) VIDEO 1 DISPLAY
RESET
R
O
I
*
*
*
*
*
*
VIDEO 1
IMAGE
ADJUSTMENT
*
*
*
S
R
H
E
_
_
_
_
_
_
*
0
1
V
V
V
V
V
V
V
A
B
B
B
B
B
B
R
P
B
C
T
E
I
_
_
_
_
_
_
_
_
_
_
*
*
*
*
*
*
PICTURE (
30 – 30) BRIGHT (
30 – 30) COLOR (
30 – 30) TINT (
30 – 30) SHARPNESS (
30 – 30) VIDEO 2 DISPLAY
RESET
R
O
I
*
*
*
VIDEO 2
IMAGE
ADJUSTMENT
*
*
*
S
R
H
E
_
_
_
*
_
_
_
*
*
0
1
*
V
B
B
B
B
R
R
B
R
E
D
E
E
W
W
W
RED (
30 – 30) BLUE (
30 – 30) RESET
VIDEO
BACKGROUND
LEVEL
*
*
*
_
_
1
E-34
Download from Www.Somanuals.com. All Manuals Search And Download.
COMMAND
PARAMETER
CONTROL ITEM
CONTROL CONTENTS
VOLUME (0 – 60)
C1 C2 C3 C4 P1 P2 P3 P4
V
M
M
A
A
A
A
A
R
R
R
R
R
R
R
R
R
R
R
R
I
O
U
U
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
N
N
A
A
A
A
M
L
T
A
E
E
L
_
_
_
_
_
_
_
_
_
_
_
_
*
*
_
_
*
*
0
1
*
VOLUME
ADJUSTMENT
MUTE OFF
MUTE ON
T
B
T
BALANCE (
30 – 30) TREBLE (
30 – 30) BASS (
30 – 30) AUDIO DISPLAY
RESET
E
A
E
E
I
*
*
*
AUDIO
ADJUSTMENT
B
R
R
P
B
R
B
R
R
P
B
R
B
R
R
C
P
H
V
R
R
B
*
*
*
_
_
*
_
_
*
0
1
*
PICTURE (
30 – 30) BRIGHT (
30 – 30) RED (
30 – 30) BLUE (
30 – 30) RGB DISPLAY
R
D
E
E
E
I
*
*
*
_
_
_
_
_
_
*
*
*
RGB 1 ADJUSTMENT
*
*
*
_
_
*
_
_
*
0
1
*
RESET
PICTURE (
30 – 30) BRIGHT (
30 – 30) RED (
30 – 30) BLUE (
30 – 30) RGB DISPLAY
R
D
E
E
E
L
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
RGB 2 ADJUSTMENT
*
*
*
_
_
*
_
_
*
0
1
*
RESET
CLOCK (
60 – 60) PHASE (
60 – 60) H-POS (
60 – 60) V-POS (
30 – 30) RGB INPUT DISPLAY
RESET
I
H
P
P
E
E
E
*
*
*
I
*
*
*
RGB INPUT
ADJUSTMENT
I
*
*
*
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
0
1
0
1
0
1
0
1
0
1
I
I
BLUE SCREEN OFF
BLUE SCREEN ON
BLACK SCREEN OFF
BLACK SCREEN ON
INPUT DISPLAY OFF
INPUT DISPLAY ON
REVERSE OFF
I
I
M
M
B
B
E
K
I
I
M
M
B
D
K
I
SCREEN SETTING
I
I
M
M
D
R
I
E
REVERSE ON
I
I
M
M
R
I
E
N
INVERT OFF
INVERT ON
I
S
I
M
I
N
E
O
VIDEO
CONFIRMATION
Y
S
B
_
_
_
_
_
_
0
0
DISPLAY
M
BLACK SCREEN DISPLAY OFF
ON-SCREEN
DISPLAY SETTING
I
M
E
E
E
E
B
M
M
M
M
O
O
O
A
A
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
2
0
*
BLACK SCREEN DISPLAY ON
REMOTE MOUSE AT
R
R
M
M
MOUSE
ADJUSTMENT
REMOTE MOUSE 98
MEMORY RELEASE
SCREEN MODE
MEMORY
MEMORY SELECTION (1 – 7)
Note:
• RGB INPUT ADJUSTMENT can only be set in the displayed computer mode.
Example:
When BRIGHT of RGB 1 IMAGE ADJUSTMENT is set to
מ 10. Computer
Unit
→
←
O
K
R
A
B
R
מ 1
0
—
E-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Wired Remote Control Terminal Specifications
1. Specifications of wired remote control input
• 3.5ø minijack
• External:
ם 5 V (1 A) • Internal: GND
2. Function and transmission codes
No.
Control Item
System Code
Data Code
External Code
Note:
C1 C2 C3 C4 C5
C6 C7 C8 C9 C10
(Function)
C11 C12 C13 C14 C15
• To operate the MOUSE, L-CLICK and R-CLICK functions
through the wired remote control input, connect the cable
from the wired remote control (supplied) terminal on the pro-
jector to the remote control. The codes for these functions are
complex and are, therefore, not listed here.
1
2
3
4
5
6
7
8
9
VOLUME UP
VOLUME DOWN
POWER ON
POWER OFF
CURSOR UP
CURSOR DOWN
ADJUST UP
ADJUST DOWN
MUTE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
1
0
1
0
0
1
1
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
1
0
1
1
1
0
1
1
1
1
1
1
1
0
1
1
0
0
1
1
1
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
1
1
0
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
0
1
0
1
0
0
0
1
1
1
0
0
0
1
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Wired remote control function code
LSB
MSB
10 MENU
C1
System Code
C5
0
C6
*
Data Code
C13 C14 C15
11 VIDEO 1
12 VIDEO 2
13 RGB1
1
0
1
1
*
*
*
*
*
*
*
1
0
14 RGB 2
• System codes C1 to C5 are fixed at “10110”.
• Codes C14 and C15 are reverse confirmation bits, with “10”
indicating “Front” and “01” indicating “Rear”.
15 ENTER
16 INPUT CHECK
17 BLACK SCREEN
3. Sharp remote control signal format
1. Transmission format
a. 15-bit format
D
D
D
D
D
D
D
D
D
D
D
D
D
67.5 ms
67.5 ms
2. Wave form of output signal
• Output using Pulse Position Modulation
t
T
1
T0
26.4 µs
“1”
“0”
“0”
“0”
“0”
“1”
“0”
t
D
• t
ס 264 µs • To
ס 1.05 ms • T1
ס 2.10 ms • Pulse carrier frequency
ס 455/12 kHz • Duty ratio
ס 1:1 3. Transmission control code
a. 15 bit
b. Example of Reverse D to
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10 C11 C12 C13 C14 C15
D
C1
1
C2
0
C3
1
C4
1
C5
0
C6
1
C7
0
C8
0
C9
0
C10 C11 C12 C13 C14 C15
0
0
0
0
1
0
Data
Expansion
Data
Deter-
System Address
Function Key Data Bit
Mask
D
C1
1
C2
0
C3
1
C4
1
C5
0
C6
0
C7
1
C8
1
C9
1
C10 C11 C12 C13 C14 C15
mination
1
1
1
1
0
1
D to D Common Data Bit
Reverse in D
E-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product Type
LCD Projector
XG-NV2SB
Model
Video system
Display method
LCD panel
PAL/SECAM/NTSC 3.58/NTSC 4.43
LCD panel
ן 3, RGB optical shutter method Panel size: 1.3 ؆ (19.8 [H]
ן 26.4 [W] mm) Display method: Translucent TN liquid crystal panel
Drive method: TFT (Thin Film Transistor) Active Matrix panel
No. of dots: 485,616 dots (804 [H]
ן 604 [V]) 1–1.6 zoom lens, F2.5 to 3.6, f
ס 47 to 76 mm 150 W UHP lamp
Lens
Projection lamp
Contrast ratio
200:1
Video input signal
RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated
RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo)
4-pin mini DIN connector
S-video input signal
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
580 TV lines (video input)
Horizontal resolution
Audio output
2 W
ם 2 W (stereo) Computer RGB input signal
Video signal
15-PIN MINI D-SUB CONNECTOR (RGB 1, 2):
RGB separate type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated
STEREO MINIJACK:
AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
HORIZONTAL SYNC. SIGNAL:
TTL level (positive/negative) or composite sync (Apple only)
VERTICAL SYNC. SIGNAL:
Same as above
Computer Control Cable (Supplied)
RS-232C input terminal
Mouse input terminal (for IBM/Mac)
Mouse input terminal (for PC98)
9-pin D-sub male connector for controlling personal computer
9-pin D-sub female connector for wireless mouse
9-pin mini DIN connector for wireless mouse
Speaker system
Rated voltage
Rated frequency
2.8Љ
ן 1.6Љ (7 ן 4 cm) oval ן 2 AC 110–120/200–240 V
50/60 Hz
Power consumption
Operating temperature
Storage temperature
Cabinet
250 W
41°F to 104°F (
ם 5°C to ם 40°C) מ 4°F to 140°F (מ 20°C to ם 60°C) Plastic
40 kHz
I/R Carrier frequency
Laser Pointer of Remote Control
Wave length
670 nm
Max. output
1 mW
Class II Laser Product
10.3؆
ן 13.0؆ ן 6.1؆ (261 ן 329 ן 155 mm)(not including lens) 14.6 lbs. (6.6 kg)
Dimensions (W
ן D ן H) Weight
Supplied accessories
Remote control unit, Four AA batteries, Extra air filter, RGB signal cable
(9.8Ј, 3 m), Computer control cable (3.3Ј, 1 m), Mouse control cable for IBM PS/2
(5.9Љ, 15 cm), Mouse control cable for Mac (5.9؆, 15 cm), Mouse control cable
(9.8Ј, 3 m), Computer audio cable, AC cord, Lens cap (installed)
Lamp unit (Lamp/cage module) (BQC-XGNV6XU/1), Remote control
(RRMCG1414CESA), Air filter (PFILD0080CEZZ), RGB signal cable
(QCNW-5050CEZZ), Computer control cable (CTANZ0711CE01), Mouse control
cable for IBM PS/2 (QCNW-4754CEZZ), Mouse control cable for Mac (QCNW-
4755CEZZ), Mouse control cable (QCNW-4620CEZZ), Computer audio cable
(QCNW-4870CEZZ), AC cord (QACCU5013CEZZ)
Replacement parts
Our projector uses LCD (Liquid Crystal Display) panels. These very
sophisticated panels contain 485,616 pixels (
ן RGB) TFTs (Thin Film Transistors).
As with any high technology electronic equipment such as large
screen TVs, video systems and/or video cameras, there are certain
acceptable tolerances that the equipment must conform to. This unit
has some inactive TFTs within acceptable tolerances, which may
result in illuminated or inactive dots on the picture screen.
This will not affect the picture quality or the life expectancy of the unit.
If you have any questions about this matter, please call toll free 1-800-
BE-SHARP (1-800-237-4277). U.S.A. ONLY
Specifications are subject to change without notice.
E-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Rear View
Top View
(Lens housed)
(Lens extended)
10.3 (261) 0.2 (5)
Side View
1.1 (29)
Front View
8.0 (204)
Bottom View
[Units: inches (mm)]
E-38
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP CORPORATION
OSAKA, JAPAN
Printed in Japan
Imprimé au Japon
Impreso en Japón
TINS-6770CEZZ
T2205-A
9P07-JWG
Download from Www.Somanuals.com. All Manuals Search And Download.
|