Sylvania Flat Panel Television 6637LCT User Manual
37 inch Digital / Analog  
LCD TV  
Owner’s Manual  
6637LCT A  
6637LCT  
INPUT  
POWER  
SLEEP SELECT  
1
4
7
2
5
8
0
3
6
AUDIO  
9
STILL  
-
SCREEN  
MODE  
SETUP  
ENTER  
INFO  
BACK  
CH RETURN  
MUTE  
VOL.  
CH  
HIGH-DEFINITION TELEVISION  
TO RECEIVE DIGITAL/ANALOG SIGNAL,  
YOU MUST CONNECT ANTENNA.  
IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER  
READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR  
VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. POWER LINES - An outside antenna system should not be located in the  
vicinity of overhead power lines or other electric light of power circuits, or  
where it can fall into such power lines or circuits. When installing an out-  
side antenna system, extreme care should be taken to keep from touching  
such power lines or circuits as contact with them might be fatal.  
d. If the TV does not operate normally by following the operating instruc-  
tions. Adjust only those controls that are covered by the operating  
instructions, as improper adjustment of other controls may result in  
damage and will often require extensive work by a qualified techni-  
cian to restore the TV to its normal operation.  
16. OVERLOADING - Do not overload wall outlets and extension cords as  
e. If the TV has been dropped or damaged in any way.  
f. When the TV exhibits a distinct change in performance, this indicates  
a need for service.  
this can result in a risk of fire or electric shock.  
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into  
this TV through openings as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock. Never spill liq-  
uid of any kind on the TV.  
18. SERVICING - Do not attempt to service this TV yourself as opening or  
removing covers may expose you to dangerous voltage or other haz-  
ards. Refer all servicing to qualified service personnel.  
20. REPLACEMENT PARTS - When replacement parts are required, be sure the  
service technician uses replacement parts specified by the manufacturer that  
have the same characteristics as the original part. Unauthorized substitutions  
may result in fire, electric shock, injury to persons or other hazards.  
21. SAFETY CHECK - Upon completion of any service or repairs to this TV,  
ask the service technician to perform routine safety checks to determine  
that the TV is in proper operating condition.  
22. HEAT - This TV product should be situated away from heat sources  
such as radiators, heat registers, stoves, or other products (including  
amplifiers) that produce heat.  
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall outlet and  
refer servicing to qualified service personnel under the following conditions:  
a. When the power supply cord or plug is damaged or frayed.  
b. If liquid has been spilled, or objects have fallen into the TV.  
c. If the TV has been exposed to rain or water.  
PRECAUTIONS  
• Place your TV in a room with adequate ventilation.  
• Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.  
• Do not place your TV on soft surfaces, such as rugs or blankets.  
• Leave enough room for air to circulate around the bottom, top and back of the set.  
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications  
to this equipment may cause harmful interference unless the modifications are expressly approved in the  
owner’s manual. The user could lose the authority to operate this equipment if an unauthorized change or  
modification is made.  
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY  
INSERT.  
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE  
DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that  
provides guidelines for proper grounding and, in particular, specifies that the cable ground should be  
connected to the grounding system of the building as close to the point of cable entry as practical.  
The serial number of this product may be found on the back of the TV. No others have the same serial num-  
ber as yours. You should record the number and other vital information here and retain this book as a perma-  
nent record of your purchase to aid identification in case of theft.  
Model No.  
Serial No.  
Dealer Purchase from  
Date of Purchase  
Dealer Phone No.  
Dealer Address  
A NOTE ABOUT RECYCLING:  
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in  
accordance with your local recycling regulations.  
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regu-  
lations concerning chemical wastes.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
SUPPLIED ACCESSORIES  
• Owner’s Manual  
(1EMN21968A)  
• Remote control unit  
(NF000UD)  
• Batteries  
(“AA” x 2)  
• If you need to replace these accessories, please refer to the PART NO. with the illustrations and call our toll  
free customer support line found on the cover of this manual.  
• Depending on your antenna system, you may need different types of Combiners (Mixers) or Separator  
(Splitters). Contact your local electronics store for these items.  
FEATURES  
• DTV/TV/CATV  
You can use your remote control to select channels which are broadcast in conventional analog, standard  
definition, and high definition formats. Also, cable subscribers can access their cable TV channels.  
• Program Information Display (DTV only)  
You can display the title, contents and other information of the current DTV program on the screen.  
• Autoscan  
This TV can automatically scan and memorize the channels receivable in your residential area. This feature elimi-  
nates the need of a difficult setting procedure.  
• V-CHIP  
This feature allows you to block children’s access to inappropriate programs.  
• Closed Caption Decoder  
This TV contains the built-in Closed Caption Decoder that displays text across the screen. It allows you to read  
the dialogue of a TV program or other information in the Closed Caption-supported programs.  
• MTS/SAP Tuner  
This feature allows you to select with the remote control your desired audio language.  
• Auto Shut Off Function  
If there is no signal input from the antenna terminal and no operation for 15 minutes, the unit will turn itself  
off automatically.  
• Choices for On-Screen Menu Language  
Select your setup menu language: English, Spanish or French.  
• Stereo Sound Function  
• Full-Function Remote Control  
• PLL Frequency Synthesized Tuning  
• HDMI Input  
This TV accepts 480i / 480p / 720p / 1080i video signals and 32kHz / 44.1kHz / 48kHz audio signals.  
• Component VIDEO Input  
This TV accepts 480i / 480p / 720p / 1080i video signals.  
• S-VIDEO Input  
• AV Input  
• Analog Audio Output  
• Digital Audio Output (Coaxial)  
• Resume  
This feature will automatically memorize settings if a power failure occurs.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ONTENTS  
C
IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
2
3
4
4
FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
REMOTE CONTROL, TOP AND REAR PANEL FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
INSTALLING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
BATTERY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
ANTENNA CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
CONNECTION TO CABLE/SATELLITE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
CONNECTING OTHER DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
8
8
8
9
9
COMPONENT CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
S-VIDEO CABLE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10  
VIDEO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
DIGITAL AUDIO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11  
ANALOG AUDIO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
INITIAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
INITIAL SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
CHANNEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
AUTOSCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
CHANNEL LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
MANUAL REGISTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
ANTENNA CONFIRMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
LANGUAGE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
WATCHING TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
CHANNEL SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
VOLUME ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
STILL MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
SELECTING AUDIO CHANNELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
ACCESSING EXTERNAL DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
CHANGING THE SCREEN DISPLAY MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
OPTIONAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
PICTURE ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
CLOSED CAPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
DTV CLOSED CAPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
CLOSED CAPTION STYLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
V-CHIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
HDMI AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover  
SYMBOLS USED IN THIS MANUAL  
The following is the description for the symbols used in this manual.  
TV  
: Analog TV operation.  
DTV  
: Digital TV operation.  
• If neither symbol appears under the function heading, operation is applicable to both.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
UNCTIONS  
F
REMOTE CONTROL, TOP AND REAR PANEL FUNCTION  
SLEEP button (p23)  
Press to activate the sleep timer.  
INPUT SELECT button (p20)  
Press to access connected external  
devices like a DVD recorder or VCR.  
INPUT  
POWER  
SLEEP  
SELECT  
POWER button (p12)  
AUDIO button (p19)  
• Analog mode (TV)  
Selects audio mode.  
• Digital mode (DTV)  
Selects audio language.  
Press to turn the TV on and off.  
1
4
7
2
5
8
0
3
6
9
Number buttons (p18)  
Press to select a channel.  
AUDIO  
STILL  
SETUP button (p23)  
Press to display on-screen menu.  
STILL button (p19)  
Press to pause screen image.  
-
K
L
s
/
B
/
/
buttons (p12)  
SCREEN  
MODE  
To move left / right / up / down through  
the items.  
SETUP  
SCREEN MODE button (p21)  
Press to select screen aspect ratio.  
ENTER button (p12)  
ENTER  
INFO button  
Press to confirm your selection.  
• Analog mode (TV) (p22)  
To display channel No., signal type  
and TV setting.  
INFO  
BACK  
BACK button (p22)  
Press to return to previous menu operation.  
CH RETURN  
MUTE  
• Digital mode (DTV) (p22)  
To display channel information, signal  
type and TV setting.  
• External input mode (p20)  
To display external input mode, signal  
type and TV setting.  
VOL.  
CH  
X
Y
VOL.  
/
buttons (p18)  
Press to adjust volume.  
MUTE button (p18)  
Press to turn sound on and off.  
K
L
CH  
/
buttons (p18/p20)  
CH RETURN button (p18)  
Press to return to previously viewed channel.  
To select channels and external input  
mode.  
SETUP button (p23)  
To display on-screen menu.  
X
Y
VOLUME  
/
buttons (p18)  
X
Y
To adjust volume and move right( )/left( ) through the  
menu items.  
K
L
CHANNEL  
/
buttons (p18)  
TV CONTROL  
To select channels and move up/down through the menu  
items.  
SETUP  
VOLUME  
CHANNEL  
INPUT SELECT/ POWER  
ENTER  
POWER button (p12)  
To turn TV on/off.  
INPUT SELECT/ENTER button (p20/p12)  
• To access connected external devices like a DVD  
recorder or VCR.  
• To decide the command of setting when the menu is  
displayed.  
Infrared Sensor Window  
Receives infrared rays transmitted from the remote  
control.  
STANDBY  
POWER ON  
NOTE:  
• With buttons [VOL. X/ Y] or [MUTE], you can only adjust the volume of the main unit. You cannot adjust the volume of the  
external devices with these buttons.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ANT. IN jack  
AUDIO OUT jacks  
Coaxial cable connection for  
your antenna or cable box.  
Audio cable connection for external  
audio equipment. Use AUDIO IN jacks  
of external equipment.  
DIGITAL AUDIO OUT  
(COAXIAL) jack  
Digital audio coaxial cable  
connection for decoder or  
audio receiver. Connect cable  
to DIGITAL AUDIO IN jack of  
external device.  
AUDIO jacks (for DVI connection)  
Audio cable connection for external  
audio/video devices with DVI jack.  
Use AUDIO OUT jacks of external  
equipment when using an HDMI-DVI  
conversion cable.  
ANT. IN  
L
L
AUDIO OUT  
AUDIO  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
HDMI IN  
R
R
HDMI  
from underneath  
HDMI IN jack  
Rear of this TV  
HDMI cable connection  
for external video  
equipment (i.e.DVD  
recorder).  
Y
Y
VIDEO  
VIDEO  
ANT.  
IN  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
L
L
L
Pb  
Pr  
L
Pb  
Pr  
L
L
S-VIDEO1  
S-VIDEO2  
A
U
D
I
O
O
U
T
A
U
D
I
O
AUDIO  
AUDIO  
AUDIO  
AUDIO  
R
R
HDMI IN  
R
R
R
R
HDMI  
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
COMPONENT1 and  
AUDIO jacks  
Component cable  
connection for external  
audio/video devices. Use  
component and audio out  
jacks of external device.  
from underneath  
S-VIDEO1 jack  
S-Video cable and audio  
(VIDEO1) cable connection for  
external video equipment.  
Y
Y
VIDEO  
VIDEO  
Pb  
Pr  
Pb  
Pr  
L
L
L
L
S-VIDEO2 jack  
S-VIDEO1  
S-VIDEO2  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
R
S-Video cable and audio  
(VIDEO2) cable connection for  
external video equipment.  
COMPONENT2 and  
AUDIO jacks  
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
Component cable  
connection for external  
audio/video devices. Use  
component and audio out  
jacks of external device.  
VIDEO1 and AUDIO jacks  
Video and audio cable  
connection for external  
equipment.  
VIDEO2 and AUDIO jacks  
Video and audio cable  
connection for external  
equipment.  
INSTALLING THE BATTERIES  
Install two AA batteries (included) matching the polarity (++ / – –) indicated inside battery compartment of  
the remote control.  
[BATTERY PRECAUTIONS]  
• Be sure to follow the correct polarity as indicated in the battery compartment.  
Reversed batteries may cause damage to the device.  
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries with fresh  
ones.  
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury  
from possible battery leakage.  
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
REPARATION FOR USE  
P
CONNECTION  
This section describes how to connect your TV to an antenna, cable box, etc.  
MAKE SURE YOU HAVE AN ANTENNA.  
As DTV is only available over the air, you need an antenna to receive a digital signal.  
NOTE:  
• Be sure your antenna or other source is connected properly before plugging in the power cord.  
[ANTENNA CABLE CONNECTION]  
1) When connecting your TV to an antenna  
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.  
2) When connecting TV to cable TV company (without box)  
Connect the Coaxial cable on your home outlet to the ANT. IN jack of this TV.  
VHF / UHF  
Rear of this TV  
antenna  
Coaxial cable  
(not included)  
or  
ANT. IN  
Y
Y
VIDEO  
VIDEO  
A
N
T
.
IN  
D
I
G
I
T
A
L
A
U
D
I
O
O
U
T
(COAXIAL)  
L
L
L
Pb  
Pr  
L
Pb  
Pr  
L
L
A
U
D
I
O
O
U
T
A
UDIO  
AUDIO  
AUDIO  
AUDIO  
AUDIO  
S-VIDEO1  
S-VIDEO2  
R
R
H
D
M
I
I
N
R
R
R
R
HDMI  
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
Coaxial cable  
Cable TV  
company  
(not included)  
*Once connections are completed, turn on the TV and begin initial setup.  
Channel scanning is necessary for the TV to memorize all available channels in your area.  
(Refer to “INITIAL SETUP” on page 12.)  
NOTES:  
• For your safety and to avoid damage to equipment, please unplug the coaxial cable from the ANT.IN jack before moving the unit.  
• If you use an antenna in order to receive analog TV, the same antenna generally will work for DTV reception.  
Outdoor or attic antennas will be more effective than set-top versions.  
• To easily switch between antenna and cable wires, you can purchase an “Antenna Selector” commercially available.  
• If you connect a cable system directly, contact the CATV installer.  
[CONNECTION TO CABLE/SATELLITE BOX]  
1) Connect the coaxial cable on your home outlet to the input jack of the CABLE/SATELLITE box.  
2) Use another coaxial cable to connect the ANT. IN jack of your TV to the output jack of the CABLE/SATEL-  
LITE box.  
*Required cables in 2) and connecting methods differ depending on the CABLE/SATELLITE box. For more informa-  
tion, please contact your cable/satellite provider.  
Rear of this TV  
Satellite  
dish  
Cable box or  
Satellite box  
or  
Y
Y
VIDEO  
VIDEO  
A
N
T
.
IN  
D
I
G
I
T
A
L
A
U
D
I
O
O
U
T
(COAXIAL)  
L
L
L
Pb  
Pr  
L
Pb  
Pr  
L
L
A
U
D
I
O
O
U
T
A
UDIO  
AUDIO  
AUDIO  
AUDIO  
AUDIO  
S-VIDEO1  
S-VIDEO2  
R
R
H
D
M
I
I
N
R
R
R
R
HDMI  
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
ANT. IN  
Coaxial cable  
Coaxial cable  
Cable TV  
company  
(not included)  
(not included)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
CONNECTING OTHER DEVICES  
[HDMI]  
1) High Definition Multimedia Interface (HDMI) uses the latest technology to ensure the signal maintains the  
highest degree of integrity from source to TV. Both video and audio travel through a single cable.  
HDMI cable (not included)  
To HDMI IN jack  
HDMI OUT  
ANT. IN  
L
L
AUDIO OUT  
AUDIO  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
HDMI IN  
To HDMI output jack  
R
R
DVD Player with the HDMI output jack  
HDMI  
Rear of this TV  
NOTES:  
• This TV accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.  
• This TV accepts only 2 channel audio signal (LPCM).  
• You need to select “PCM” for the digital audio output of the device you connect or the HDMI audio setting. Audio sometimes makes  
no sound if you select “Bitstream”, etc.  
• This TV only accepts signals corresponding EIA861.  
2) When your video device has a DVI output jack, connect the HDMI conversion cable (not included) from the  
DVI output jack.  
HDMI-DVI conversion cable (not included)  
To HDMI IN jack  
To DVI output jack  
DVI OUT  
ANT. IN  
L
L
AUDIO OUT  
AUDIO  
AUDIO OUT  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
HDMI IN  
Cable Box or Satellite Box  
with the DVI output jack  
R
L
R
HDMI  
To AUDIO Rear of this TV  
input jacks  
To audio  
output jacks  
Audio cable (not included)  
NOTES:  
• This TV accepts 480i / 480p / 720p / 1080i video signals.  
• An HDMI conversion cable requires a separate audio cable connection as well.  
• Audio signals are converted from digital to analog if you make the connection in paragraph 2) above.  
• DVI does not show image if the 480i does not accept EIA/CEA-861/861B.  
“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered  
trademarks of HDMI Licensing LLC.”  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
[COMPONENT CABLE CONNECTION]  
Offers better picture quality for video devices connected to your TV.  
Use a component video cable (not included) to connect your TV to external video devices equipped with  
component video jacks.  
If you connect to your TV’s COMPONENT1 input jack, connect audio cables to the AUDIO L/R jacks of COM-  
PONENT1.  
If you connect to your TV’s COMPONENT2 input jack, connect audio cables to the AUDIO L/R jacks of COM-  
PONENT2.  
Component video cable (not included)  
To COMPONENT1  
input jacks  
To component video  
output jacks  
Y
Y
VIDEO  
VIDEO  
Pb  
Pr  
Pb  
Pr  
L
L
L
L
S-VIDEO1  
S-VIDEO2  
DVD Player with the component  
video output jacks  
AUDIO  
R
AUDIO  
R
AUDIO  
R
AUDIO  
R
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
To audio  
output jacks  
To AUDIO  
input jacks  
Rear of this TV  
Audio cable (not included)  
NOTE:  
• This TV accepts 480i / 480p / 720p / 1080i video signals.  
[S-VIDEO CABLE CONNECTION]  
Offers good picture quality for video devices connected to your TV.  
Use an S-video cable (not included) to connect your TV to external video devices equipped with S-video con-  
nectors.  
If you connect to your TV’s S-VIDEO1 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO1.  
If you connect to your TV’s S-VIDEO2 input jack, connect audio cables to the AUDIO L/R jacks of VIDEO2.  
To S-VIDEO1  
input jack  
S-video cable (not included)  
To S-Video  
output jack  
Y
Y
VIDEO  
VIDEO  
AUDIO  
OUT  
VIDEO S-VIDEO  
OUT OUT  
Pb  
Pb  
Pr  
L
L
L
L
S-VIDEO1  
S-VIDEO2  
AUDIO  
R
AUDIO  
R
AUDIO  
AUDIO  
R
Pr  
DVD/VCR with  
the S-Video output jack  
To audio  
output jacks  
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
To AUDIO Rear of this TV  
input jacks  
Audio cable (not included)  
NOTE:  
• If you connect to the S-VIDEO jack and the VIDEO jack at the same time, the S-video connection will have priority.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
[VIDEO CONNECTION]  
Offers standard picture quality for video devices connected to your TV.  
When the audio jack of the video device is monaural, connect the audio cable to the audio L input jack.  
To VIDEO1  
input jack  
Video cable (not included)  
To video  
output jack  
Y
Y
VIDEO  
VIDEO  
AUDIO  
OUT  
VIDEO  
OUT  
Pb  
Pr  
Pb  
Pr  
L
L
L
L
S-VIDEO1  
S-VIDEO2  
Camcorder  
Video Game  
AUDIO  
R
AUDIO  
R
AUDIO  
AUDIO  
R
To audio  
output jacks  
COMPONENT2  
COMPONENT1  
VIDEO2  
VIDEO1  
VCR  
To AUDIO Rear of this TV  
input jacks  
Audio cable (not included)  
[DIGITAL AUDIO CONNECTION]  
If you connect this TV to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital  
broadcasting sound. Required digital audio coaxial cable not included.  
Digital audio coaxial cable  
(not included)  
To DIGITAL AUDIO  
OUT jack  
MD deck, DAT deck, etc.  
COAXIAL  
ANT. IN  
L
L
AUDIO OUT  
AUDIO  
DIGITAL  
AUDIO OUT  
(COAXIAL)  
HDMI IN  
To coaxial digital  
audio input jack  
R
R
HDMI  
Rear of this TV  
Dolby Digital decoder  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
[ANALOG AUDIO CONNECTION]  
If you connect this TV to an external analog audio device, you can enjoy stereophonic (2 channel) audio  
sound. Required audio cable not included.  
To audio input jacks  
AUDIO  
IN  
ANT. IN  
L
L
AUDIO OUT  
AUDIO  
DIGITAL  
AUDIO
(COAXIAL)  
HDMI IN  
R
R
HDMI  
Stereo system  
Rear of this TV  
To AUDIO  
OUT jacks  
Audio cable  
(not included)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
NITIAL SETTINGS  
I
INITIAL SETUP  
3 When you first turn on your TV, the following  
K
L
screen is displayed. Use [ / ] to select the  
on-screen menu language from the choices on  
the right side of the screen.  
This section will guide you through your TV’s initial  
set up which includes selecting a language for your  
on-screen menu and AUTOSCAN, which automati-  
cally scans and memorizes viewable channels.  
Initial Setup  
English  
Español  
Français  
Select the language for setup display.  
Elija idioma de preparación.  
INPUT  
POWER  
SLEEP  
SELECT  
Sélectionner langue écran config.  
1
4
7
2
5
8
0
3
6
9
SETUP Exit  
ENTER  
Select  
Enter  
AUDIO  
STILL  
The Antenna Confirmation menu on step 4 will  
be displayed in the selected language after you  
press [ENTER].  
-
SCREEN  
MODE  
SETUP  
ENTER  
K
L
4 Select source of ANT. IN jack using [ / ], then  
INFO  
BACK  
press [ENTER].  
Make sure the antenna is connected to "ANT IN" jack.  
Select the destination of "ANT IN" jack.  
1 After making all the necessary connections, turn  
on your TV.  
Air  
Cable  
Or  
2 Press [POWER]. Initial Setup menu will appear.  
ANT IN  
BACK  
SETUP Exit  
ENTER  
• This operation may take a few moments.  
Select  
Enter  
Back  
• If Initial Setup menu does not appear, press  
and hold [ENTER] for 3 seconds, initial setup  
will appear then proceed to step 3. If initial set  
up has already been completed, refer to  
“LANGUAGE SELECTION” on page 17.  
5 Autoscan will start automatically.  
• When scanning has completed, the lowest  
memorized channel will be displayed.  
NOTES:  
• The initial Autoscan function can be executed for either “Air”  
or “Cable” only once. When you change the connection  
(Air/Cable), set the “Autoscan” again. (Refer to page 13.)  
• If you connect a cable system directly, contact the  
CATV installer.  
• When the scanning is not complete, Helpful Hint will be  
displayed every time you turn on the power. If you have  
previously registered channels when this screen appears  
you can select a channel with [the Number buttons].  
2-0  
No channel is registered.  
Press and hold "ENTER" key for 3 seconds.  
Contact support hotline provided on manual or back of unit.  
Sin canal registrado.  
Mantenga oprimida la tecla "ENTER" durante 3 segundos.  
Llame teléfono de apoyo en manual o atrás de TV.  
Pas de chaîne consign.  
Maintenir la touche "ENTER" pressée 3 secondes.  
Contacter numero d'urgence dans manuel ou arrière appareil.  
• Toll free customer support line can be found on the cover  
of this manual.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
HANNEL SETTINGS  
C
AUTOSCAN  
K
L
3 For TV channels, using [ / ], select “Air”.  
For CATV channels, select “Cable”.  
Autoscan  
With AUTOSCAN, your TV automatically scans and  
memorizes your area’s viewable channels. Activate  
AUTOSCAN when you turn on your TV for the first  
time, change broadcast sources (e.g. from antenna  
to CATV), or move your TV to a different broadcast  
Back  
Autoscan will rescan all channels.  
This may take a while to complete.  
Air  
Select the destination of "ANT IN" jack.  
Cable  
Cable  
1hour  
Air  
area.  
Cable  
Or  
ANT IN  
STILL  
-
0
SCREEN  
MODE  
SETUP  
• Press [ENTER].  
Scanning and memorizing the channels auto-  
ENTER  
matically starts.  
INFO  
BACK  
CH RETURN  
MUTE  
Now the system is scanning for channels, please wait.  
72%  
VOL.  
CH  
Analog channels  
Digital channels  
10ch  
6ch  
SETUP Exit  
NOTE:  
• Make sure the TV is connected to antenna or cable.  
• When the scanning and memorizing are com-  
pleted, the lowest memorized channel in the  
broadcasting will be displayed.  
1 Display the setup screen.  
• Press [SETUP].  
NOTES:  
The following setup screen appears.  
• If you connect a cable system directly, contact the  
CATV installer.  
• If you press [POWER] or [SETUP] during Autoscan, this  
setting will be canceled.  
• If there is no reception connected or a poor signal is detect-  
ed, a Hint will appear on screen once scanning stops.  
2 Select “CHANNEL” and press [ENTER] to con-  
firm.  
K
L
• Using [ / ], select “Autoscan”.  
Channel  
Autoscan  
Channel List  
Manual Register  
Antenna  
• Press [ENTER].  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
CHANNEL LIST  
3 Select the channel you want to remove.  
K
L
This function lets you remove undesired channels  
from the Channel Registration List.  
• Using [ / ], select the channel.  
Channel List  
7
8
9
Highlight channels for  
Ch Up/Down key selection.  
DTV  
DTV  
6
8
STILL  
9
-
0
27  
48  
58  
SCREEN  
MODE  
SETUP  
DTV  
DTV  
67  
BACK  
ENTER  
Ch Select  
Watch/Skip  
Back  
ENTER  
INFO  
BACK  
• Press [ENTER] to highlight the channel select-  
ed for removal. You will not be able to select the  
CH RETURN  
MUTE  
K
L
channel again using [CH / ].  
• To reactivate the removed channel, highlight it  
and press [ENTER].  
VOL.  
CH  
• When you remove a major channel, you  
remove its minor channels, too.  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
NOTE:  
• The channel with “DTV” indicated on the display is ATSC,  
otherwise the channel is NTSC.  
4 To exit the setup, press [SETUP].  
2 Select “CHANNEL” and press [ENTER] to con-  
firm.  
K
L
• Using [ / ], select “Channel List”.  
Channel  
Autoscan  
Channel List  
Manual Register  
Antenna  
• Press [ENTER].  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
MANUAL REGISTER  
3 Select the channel you want to add.  
• Using [the Number buttons], select your  
desired channel.  
This function lets you manually add channels not  
memorized due to poor broadcast strength during  
AUTOSCAN.  
11  
INPUT  
Manual Register  
POWER  
SLEEP  
SELECT  
Register  
For Analog channels,  
select a channel to register  
using number keys.  
For Digital channels,  
you must perform Autoscan function.  
1
4
7
2
5
8
0
3
6
9
AUDIO  
STILL  
BACK  
Back  
Ch Change  
-
• Select “Register” with [ENTER].  
SCREEN  
MODE  
SETUP  
4 To exit the setup, press [SETUP].  
ENTER  
INFO  
BACK  
NOTES:  
• If set up completes successfully, “Registered to the Channel  
List” is displayed.  
• If Video 1 is being used, set up will not be completed suc-  
cessfully and “Unavailable” will be displayed on the screen.  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
2 Select “CHANNEL” and press [ENTER] to con-  
firm.  
K
L
• Using [ / ], select “Manual Register”.  
Channel  
Autoscan  
Channel List  
Manual Register  
Antenna  
• Press [ENTER].  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ANTENNA CONFIRMATION  
• If the channel is set to external input, you can-  
not confirm the antenna situation.  
Displays signal strength for each channel.  
Video1  
INPUT  
POWER  
SLEEP  
SELECT  
Antenna  
Back  
1
4
7
2
5
8
0
3
6
9
Indicator is available  
for antenna signal only.  
AUDIO  
STILL  
CH  
Ch Change  
-
SCREEN  
MODE  
SETUP  
3 To exit the setup, press [SETUP].  
ENTER  
INFO  
BACK  
CH RETURN  
MUTE  
VOL.  
CH  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
2 Select “CHANNEL” and press [ENTER] to con-  
firm.  
K
L
• Using [ / ], select “Antenna”.  
Channel  
Autoscan  
Channel List  
Manual Register  
Antenna  
• Press [ENTER].  
K
L
• Using [the Number buttons] or [CH / ],  
select the channel for which you want to check  
signal strength.  
11  
Antenna  
Back  
Now  
70 Peak  
80  
CH  
Ch Change  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
LANGUAGE SELECTION  
You can choose English, Spanish, or French as  
your on screen language.  
STILL  
0
SCREEN  
MODE  
SETUP  
ENTER  
INFO  
BACK  
CH RETURN  
MUTE  
VOL.  
CH  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
2 Select “LANGUAGE” and press [ENTER] to con-  
firm.  
K
L
• Using [ / ], select “English”, “Español” or  
“Français”.  
English  
• Press [ENTER].  
3 To exit the setup, press [SETUP].  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ATCHING TV  
W
NTSC  
ATSC  
18:00  
18:30  
19:00  
19:30  
20:00  
CHANNEL SELECTION  
CH4-1 No signal No signal  
Select channels by pressing [CH K/L] found on  
remote control or on the TV’s control panel, or by  
pressing [the Number buttons] found on the remote  
control.  
CH4-1 CH4-2 CH4-3  
CH4  
CH4-1 No signal CH4-3  
CH4-1 CH4-2 No signal  
INPUT  
POWER  
SLEEP  
SELECT  
1
4
7
2
5
8
0
3
6
9
: change automatically  
: change manually by pressing [CH / ]  
on your remote control  
AUDIO  
STILL  
-
SCREEN  
MODE  
SETUP  
NOTE:  
• “No Signal” will appear on the screen after the minor  
channel broadcast is over.  
ENTER  
You will need to change the channel to continue  
watching another TV program.  
INFO  
BACK  
CH RETURN  
MUTE  
VOLUME ADJUSTMENT  
VOL.  
CH  
This section describes how to adjust the volume.  
The mute function, which turns the sound off and  
on, will also be described.  
K
L
[CH / ]  
INFO  
BACK  
K
L
• Use [CH / ] to change the channel.  
• Same operation is also available with [CHAN-  
CH RETURN  
MUTE  
K
L
NEL / ] on the top panel of the main unit.  
VOL.  
CH  
[the Number buttons]  
•
Press the channel number with [the Number  
buttons] to select a channel you want to watch,  
then press [ENTER].  
X
Y
[VOL. / ]  
- When selecting analog channel 12  
X
Y
•
Use [VOL. / ] to adjust the audio volume.  
• The same operation is available with [VOLUME  
ENTER  
1
2
X
Y
/ ] on the top panel of the main unit.  
• The volume bar will be displayed at the bottom  
of the screen when adjusting the volume.  
- When selecting digital channel 12-1  
Be sure to press [–] before entering the minor  
channel number.  
Volume  
20  
ENTER  
1
2
1
• The volume bar display will automatically dis-  
appear in a few seconds.  
•
If the channel broadcasts NTSC and ATSC both  
and you don't press [–], you will receive the  
NTSC channel only. The moment you press [–],  
the lowest memorized digital channel will be dis-  
played.  
[MUTE]  
• Press [MUTE] to turn off and on the sound.  
Mute  
• Press [CH RETURN] to return to the previously  
viewed channel.  
• “Mute” is displayed on the screen for a few sec-  
onds.  
NOTE:  
• In DTV broadcasting, one channel sometimes broadcasts  
multiple programs depending on the air time. In this case,  
the main channel is called major channel and the minor  
channel is called minor channel.  
X
Y
• Press [MUTE] again or [VOL.  
/
] ([VOLUME  
X Y  
/
]) to release the Mute status.  
About minor channel broadcasting:  
There may be different programs being broad-  
cast on minor channels through a single chan-  
nel from ATSC. You can watch each minor  
channel program being broadcast by selecting  
one of the minor channels.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
STILL MODE  
When the broadcasting has all audio...  
You can freeze the image shown on the screen.  
SAP / STEREO  
SAP / MONO  
1
4
7
2
5
8
0
3
6
9
SAP / STEREO  
When the broadcasting has stereo audio and  
monaural audio...  
AUDIO  
STILL  
-
MONO / STEREO  
MONO / STEREO  
SCREEN  
MODE  
SETUP  
When the broadcasting has SAP and monaural  
audio...  
SAP / MONO  
SAP / MONO  
1 Pause the image.  
• When you press [STILL], the image shown on  
When the broadcasting is having only monaural  
audio...  
the screen is paused.  
MONO  
Still  
(cannot be switched.)  
• The audio is not paused and keeps on reading  
out.  
STEREO : Outputs stereo-audio  
SAP  
: Outputs second audio program  
• If the digital signal is gone or protected, the  
image will remain paused and the audio will be  
muted.  
MONO : Outputs mono-audio  
DTV  
• The Still function will be released after 5  
minutes.  
When you press [AUDIO], the currently selected  
language and the number of available languages  
will be displayed on the screen.  
2 Canceling Still function.  
• The Still function will be canceled by pressing  
any button while Still function is working.  
6-1  
English 1/3  
NOTE:  
Press [AUDIO] to cycle through available audio  
languages.  
• Press any key except [POWER] to cancel still mode.  
English 1/3  
Spanish 2/3  
SELECTING AUDIO CHANNELS  
Other 3/3  
This section describes how to switch the audio in  
the analog mode and how to switch the audio lan-  
guage in the digital mode.  
• Available languages differ depending on the  
broadcast.  
AUDIO  
7
8
0
9
• The information display will automatically dis-  
appear in one minute.  
STILL  
-
SCREEN  
MODE  
SETUP  
NOTE:  
• Pressing [AUDIO] does not control external audio source.  
TV  
When you press [AUDIO], the currently selected  
audio mode will be displyed on the screen.  
6
SAP / STEREO  
Press [AUDIO] to cycle through available audio  
channels.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ACCESSING EXTERNAL DEVICES  
• When you press [INFO], the current external  
input mode, the type of resolutions for video  
signal, TV aspect ratio, CC and TV rating will  
be displayed at the top-right of the screen.  
Use your remote control to access DVD recorders,  
home audio systems and other external devices  
when they are connected to your television.  
• The information display will automatically dis-  
appear in 1 minute.  
INPUT  
POWER  
SLEEP  
SELECT  
1
4
7
2
5
8
0
3
6
9
1) When using VIDEO1 or S-VIDEO1 input jack  
AUDIO  
STILL  
Video1  
480i SD  
TV-PG DLSV CC  
-
SCREEN  
MODE  
SETUP  
ENTER  
2) When using VIDEO2 or S-VIDEO2 input jack  
INFO  
BACK  
Video2  
480i SD  
CH RETURN  
MUTE  
TV-PG DLSV CC  
VOL.  
CH  
Use your remote control to select external com-  
ponent.  
3) When using COMPONENT1 input jacks  
L
]
• When you press [INPUT SELECT] or [CH  
Component1  
1080i HD  
on the remote control, the input mode will be  
NONE  
switched as below.  
TV/DTV channel  
4) When using COMPONENT2 input jacks  
Video1  
Component2  
1080i HD  
NONE  
Video2  
Component1  
Component2  
HDMI  
5) When using HDMI IN jack  
HDMI  
1080i HD 16:9  
NONE  
• Pressing [CH K] on the remote control reverses  
direction.  
• To use the VIDEO1 or S-VIDEO1 input jack on  
the TV, select “Video1”.  
• To use the VIDEO2 or S-VIDEO2 input jack on  
the TV, select “Video2”.  
• To use the COMPONENT1 input jacks on the  
TV, select “Component1”.  
• To use the COMPONENT2 input jacks on the  
TV, select “Component2”.  
• To use the HDMI IN jack on the TV,  
select “HDMI”.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
CHANGING THE SCREEN DISPLAY MODE  
1 Press [SCREEN MODE], to switch the TV  
Each of 4 display modes can be selected in either  
aspect ratio.  
4:3 or 16:9 aspect ratios.  
AUDIO  
2 Press [SCREEN MODE] repeatedly until the nor-  
7
8
0
9
STILL  
mal screen displays.  
-
SCREEN  
MODE  
NOTE:  
SETUP  
• Some programs may not offer all display mode options.  
ENTER  
INFO  
BACK  
When the broadcast is sending 4:3 video  
signal...  
When the broadcast is sending 16:9 video  
signal...  
Sidebar  
(normal)  
Full  
Zoom  
Full  
(normal)  
Expand  
Cinema  
Wide  
Cinema  
[Sidebar]  
[Full]  
Sidebar displays a 4:3 picture at its standard  
4:3 size. Sidebars will be displayed on the right  
and left edges of the screen.  
A picture is displayed at 16:9 size as it is.  
[Zoom]  
Zoom displays a 16:9 picture without changing  
its horizontal and vertical ratio, at its maximum  
size.  
[Full]  
Full displays a 4:3 picture at a 16:9 size, with  
horizontal elongation necessary to fill the  
screen.  
[Cinema]  
Cinema displays a 16:9 picture with vertical  
elongation.  
[Cinema]  
Cinema displays a 4:3 picture at a 16:9 size,  
with less horizontal elongation necessary to fill  
the screen because a little bit of the top and  
bottom edge of the screen will be cut off.  
[Expand]  
Expand displays a 16:9 picture with horizontal  
elongation.  
[Wide]  
Wide displays the center of the picture as original  
size and the outer sides of the picture will be  
elongated. The size of the picture will depend on  
the original signal.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DTV  
SCREEN INFORMATION  
In the digital mode, the detailed information for the  
current channel such as the Program guide is dis-  
played.  
You can display the currently selected channel or  
other information such as the audio mode on the  
screen.  
AUDIO  
1 Display the detailed information for the channel.  
7
8
0
9
STILL  
• Press [INFO] on the remote control.  
The currently selected program details are dis-  
played on the screen.  
-
SCREEN  
MODE  
SETUP  
• The following information is displayed.  
(1) Program title  
ENTER  
INFO  
BACK  
(2) Broadcast station  
CH RETURN  
MUTE  
(3) Program guide (max. 4 lines displayed)  
(4) Channel number  
VOL.  
CH  
(5) Audio language (“Other” is displayed when  
the audio language cannot be acquired, or  
the acquired languages are other than  
English, Spanish or French.)  
TV  
In the analog mode, the current channel and the  
audio mode are displayed.  
(6) Effective scanning lines and scan mode  
(7) Program definition  
1 Display the channel number and the audio  
mode.  
(8) Program aspect ratio  
• Press [INFO] on the remote control.  
The current channel number, audio mode, type  
of resolutions for video signal, TV aspect ratio,  
CC and TV rating are displayed at the top-right  
of the screen.  
(9) Program rating  
(10) CC (Not available if the CC set to “Off”)  
(1)  
(2)  
(4)  
Buffy Vampire Slayer  
HDTV  
6-1  
English 1/2  
6
A quarter-century ago,which may now qualify as the  
good old days of newspapering,run-of-paper sales  
accounted for 80 percent of the industry's advertising  
revenues.Department stores and supermarket were  
(5)  
SAP / STEREO  
1080i HD 16:9  
480i SD  
4:3  
CC  
TV-PG DLSV  
CC  
TV-PG DLSV  
(6), (7), (8)  
(3)  
(9) (10)  
NOTES:  
• To clear the display, press [BACK] or [INFO]  
again.  
• When the program guide is displayed in more than 4 lines,  
K
/
L
use [  
] to scroll.  
• “No description provided” is displayed when the program  
guide is not provided.  
• The following screen is displayed when con-  
necting to external devices:  
e.g.) When using VIDEO1 input jack for connec-  
tion (Refer to “ACCESSING EXTERNAL  
DEVICES” on page 20.)  
Video1  
480i SD  
CC  
TV-PG DLSV  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PTIONAL SETTINGS  
O
SLEEP TIMER  
SETUP SCREEN  
The Sleep Timer can be set to automatically turn  
off your television after an incremental period of  
time.  
This section describes the overview of the setup  
screen displayed when you press [SETUP].  
For more details, see the reference page for each  
item.  
INPUT  
POWER  
SLEEP  
SELECT  
The setup screen consists of the function setting  
items below.  
1
4
7
2
5
8
0
3
6
9
•
AUDIO  
STILL  
To exit settings.  
-
•
SCREEN  
MODE  
SETUP  
You can adjust the picture quality (Picture Mode,  
Brightness, Contrast, Color, Tint, Sharpness,  
Color Temp., and Energy Saving).  
(Refer to “PICTURE ADJUSTMENT” on page 24.)  
1 Press [SLEEP] on the remote control to set the  
Sleep Timer.  
•
• The setting display for Sleep Timer is shown on  
the screen.  
You can automatically scan the viewable channels  
and remove those that are undesired.  
(Refer to “AUTOSCAN” on page 13.)  
Sleep  
Off  
•
You can change closed captioning display formats  
and font styles. (Refer to “CLOSED CAPTION” on  
page 25.)  
Block children’s access to inappropriate program-  
ming. (Refer to “V-CHIP” on page 28.)  
And select HDMI Audio if your TV is connected to  
a digital external device like a DVD recorder.  
(Refer to “HDMI AUDIO” on page 31.)  
2 You can set your TV to turn off after a set period  
of time (from 10 to 90 minutes). After set up, you  
can display the remaining time before shut off by  
pressing [SLEEP] again.  
• To cancel the sleep timer, press [SLEEP]  
repeatedly until “Sleep Off” is displayed.  
Sleep  
Off  
•
• The Sleep Timer setting display will automati-  
cally disappear in a few seconds.  
You can change the language (English, Spanish,  
French) displayed on the setup screen.  
NOTE:  
• When you disconnect your TV from its power source or  
when a power failure occurs, the sleep timer setting will be  
cancelled.  
(Refer to “LANGUAGE SELECTION” on page 17.)  
NOTE:  
• To cancel the setup screen, press [SETUP].  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Contrast  
Using [s  
contrast.  
s
PICTURE ADJUSTMENT  
/
B], adjust to increase or decrease  
You can select from four default picture color set-  
tings. You can also adjust brightness, contrast,  
color, tint, sharpness and color temperature as well  
as energy saving settings.  
: To decrease contrast  
: To increase contrast  
B
Contrast  
60  
SCREEN  
MODE  
SETUP  
Color  
Using [s  
s
/
B], adjust to be brilliant or pale color.  
ENTER  
: To pale  
: To brilliant  
INFO  
BACK  
B
1 Display the setup screen.  
Tint  
• Press [SETUP].  
Using [s / B], adjust to obtain natural skin tones.  
The following setup screen appears.  
s
: To red  
B
: To green  
Tint  
R2  
Sharpness  
Using [s  
/
B], adjust the detail of the picture.  
s
: To soft  
B
: To clear  
2 Select “PICTURE”, and press [ENTER] to con-  
Sharpness  
0
firm.  
K
L
• Using [ / ], select your desired item and  
press [ENTER] to confirm.  
Reset Settings  
K
L
Using [ / ], select “Reset”.  
Picture  
Dynamic  
30  
Picture Mode  
Brightness  
Contrast  
You can reset setting of the Picture Mode you select.  
Reset Settings  
60  
36  
0
Color  
This function resets the  
"Dynamic" setting for Picture Mode  
to factory default.  
Cancel  
Reset  
Tint  
Sharpness  
Reset Settings  
Color Temp.  
Energy Saving  
0
Neutral  
Off  
3 Adjust the picture quality.  
K
L
Color Temp.  
Using [ / ], adjust Color Temperature from the selec-  
tion, then press [ENTER]. (Cool, Neutral and Warm)  
Picture  
• Using [ / ], select the picture quality you want  
to adjust.  
K
L
Picture Mode  
K
L
Using [ / ], adjust Picture Mode from the  
Picture Mode  
Brightness  
Contrast  
Color  
selection, then press [ENTER]. (Standard,  
Dynamic, Movie and News)  
Tint  
Sharpness  
Picture  
Reset Settings  
Color Temp.  
Cool  
Picture Mode  
Brightness  
Contrast  
Standard  
Dynamic  
Movie  
Neutral  
Warm  
Energy Saving  
Color  
News  
Tint  
Energy Saving  
Sharpness  
Reset Settings  
Color Temp.  
Energy Saving  
Using [s  
/
B], adjust brightness of backlight.  
s
: To bright  
: To dark  
B
Brightness  
Using [s B], adjust until the darkest parts of  
/
the picture are as bright as you prefer.  
• The adjustment bar for picture quality item is  
displayed on the screen.  
s
: To decrease brightness  
B
: To increase brightness  
NOTE:  
• To cancel the picture adjustment, press [SETUP].  
4 To exit the setup, press [SETUP].  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
[Caption Mode]  
CLOSED CAPTION  
CC1 and Text1:  
are the primary caption and text services.  
The captioning or text is displayed in the same  
language as the program’s dialogue  
You can view closed captioning (cc) for TV pro-  
grams, movies, news, and prerecorded tapes.  
Closed captions refer to text of dialogue or descrip-  
tions displayed on-screen for the hearing impaired.  
(up to 4 lines of script on the screen, where it  
does not obstruct relevant parts of the picture).  
0
SCREEN  
MODE  
SETUP  
CC3 and Text3:  
serve as the preferred data channels.  
The captioning or text is often a secondary lan-  
guage translation, simplified English or displayed  
at a slower rate.  
ENTER  
INFO  
BACK  
CH RETURN  
MUTE  
CC2, CC4, Text2 and Text4:  
VOL.  
CH  
are rarely available and broadcasters use them  
only in special conditions, such as when CC1  
and CC3 are not available or Text1 and Text3 are  
not available.  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
• There are three display modes according to  
programs:  
Paint-on mode : Displays input characters on  
the screen immediately.  
Pop-on mode : Once characters are stored in  
memory, they are displayed all  
at once.  
Roll-up mode : Displays the characters contin-  
uously by scrolling (max. 4  
2 Select “DETAIL” and press [ENTER] to confirm.  
K
L
• Using [ / ], select “Closed Caption” and press  
lines).  
[ENTER] to confirm.  
Detail  
5 To exit the setup, press [SETUP].  
Closed Caption  
V–chip  
NOTES:  
Auto  
HDMI Audio  
• Closed captions must be broadcast or included in your  
recorded content to appear on your TV.  
• Closed captions will not be displayed when you are using  
an HDMI connection.  
• If the closed caption is not broadcasted, nothing is dis-  
played.  
3 Select “Conventional CC” and press [ENTER] to  
• The closed caption is not displayed when you use HDMI  
connection.  
confirm.  
Closed Caption  
• When your TV receives a special effects playback signal  
(i.e., Search, Slow and Still) from a VCR’s video output  
channel (CH3 or CH4), the TV may not display the correct  
caption or text.  
Conventional CC  
DTV CC  
Off  
Off  
CC Style  
• Captions and texts may not match the TV voice exactly.  
• Interference may cause the closed caption system not to  
function properly.  
• The caption or text characters will not be displayed while the  
menu display or functions display is shown.  
• If a black box appears on the screen, this means that the  
TV is set to TEXT mode. To clear screen, select CAPTION  
“CC1”, “CC2” , “CC3”, “CC4”or “Off”.  
4 Select the Closed Caption mode.  
Closed Caption  
Conventional CC  
DTV CC  
Off  
CC1  
CC2  
CC3  
CC4  
Text1  
Text2  
Text3  
Text4  
CC Style  
K
L
• Using [ / ], select the desired closed caption,  
then press [ENTER].  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
DTV CLOSED CAPTION  
CLOSED CAPTION STYLE  
DTV  
1 Display the setup screen.  
Apart from closed captions, DTV has its own closed  
captions called DTV CC. Use this menu to change  
the settings for DTV CC.  
• Press [SETUP].  
The following setup screen appears.  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
2 Select “DETAIL” and press [ENTER] to confirm.  
K
L
• Using [ / ], select “Closed Caption” and press  
[ENTER] to confirm.  
Detail  
Closed Caption  
V–chip  
2 Select “DETAIL” and press [ENTER] to confirm.  
Auto  
HDMI Audio  
K
L
• Using [ / ], select “Closed Caption” and press  
[ENTER] to confirm.  
Detail  
Closed Caption  
V–chip  
Auto  
HDMI Audio  
3
Select “CC Style” and press [ENTER] to confirm.  
Closed Caption  
Conventional CC  
DTV CC  
Off  
Off  
CC Style  
3 Select “DTV CC” and press [ENTER] to confirm.  
Closed Caption  
Conventional CC  
DTV CC  
Off  
Off  
CC Style  
4 Switch the Closed Caption Style.  
CC Style  
User Setting  
Font Style  
Off  
Font0  
Middle  
White  
Solid  
Black  
Solid  
Black  
Font Size  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
4 Switch the DTV Closed Caption mode.  
Closed Caption  
None  
Conventional CC  
Off  
DTV CC  
CC Style  
Service1  
Service2  
Service3  
Service4  
Service5  
Service6  
K
L
• Using [ / ], select the desired Closed Caption  
Style.  
5 Use “User Setting”.  
• The “User Setting” function lets you change CC  
style.  
K
L
• Using [ / ], select the desired DTV Closed  
Caption, then press [ENTER].  
K
L
• Using [ / ], select “User Setting”.  
Off:  
• Press [ENTER] and set “User Setting” to “On”.  
Select if you do not want DTV CC. This is the  
CC Style  
default.  
User Setting  
Font Style  
On  
Off  
Service 1 to Service 6:  
Font Size  
Select one of these before changing any other  
item in the Closed Caption menu. Choose  
Service 1 under normal circumstances.  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
5 To exit the setup, press [SETUP].  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
[Font Opacity]  
Font opacity of the displayed caption can be  
switched as below.  
6 Set each item.  
• When “User Setting” is set to “On”, you can set  
the following items.  
CC Style  
User Setting  
Closed Caption  
• CC style set by “User Setting” will be displayed.  
Font Style  
Font Size  
K
L
• Using [ / ], select the item you want to set.  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
Solid  
• You can switch the setting for each item with  
Flash  
Translucent  
Transparent  
K
L
[ / ].  
Picture display  
[Back Color]  
Background color of the displayed caption can  
ABCDEFGHIJKL  
be switched as below.  
CC Style  
User Setting  
Closed Caption  
Edge  
Font Style  
Font Size  
(Edge Color and Edge Type)  
White  
Black  
Red  
Font  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
(Font Style, Font Size, Font Color and Font Opacity)  
Green  
Blue  
Back  
Yellow  
Magenta  
Cyan  
(Back Color and Back Opacity)  
• The setting description for each item is shown  
below.  
[Back Opacity]  
Background opacity of the displayed caption can  
be switched as below.  
[Font Style]  
Closed Captioning font style can be changed as  
CC Style  
User Setting  
Closed Caption  
below.  
CC Style  
User Setting  
Closed Caption  
Font Style  
Font Size  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
Font Style  
Font Size  
Solid  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
Flash  
Translucent  
Transparent  
[Edge Color]  
Edge color of the displayed caption can be  
switched as below.  
[Font Size]  
Font size of the displayed caption can be  
CC Style  
switched as below.  
Closed Caption  
User Setting  
CC Style  
User Setting  
Closed Caption  
Font Style  
Font Size  
White  
Black  
Red  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Font Style  
Font Size  
Green  
Blue  
Large  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
Middle  
Small  
Yellow  
Magenta  
Cyan  
Edge Color  
Edge Type  
[Edge Type]  
Edge type of the displayed caption can be  
switched as below.  
[Font Color]  
Font color of the displayed caption can be  
CC Style  
User Setting  
Closed Caption  
switched as below.  
CC Style  
User Setting  
Closed Caption  
Font Style  
Font Size  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
None  
Font Style  
Font Size  
White  
Raised  
Black  
Red  
Depressed  
Uniform  
Font Color  
Font Opacity  
Back Color  
Back Opacity  
Edge Color  
Edge Type  
Green  
Blue  
L.Shadow  
R.Shadow  
Edge Color  
Edge Type  
Yellow  
Magenta  
Cyan  
7 To exit the setup, press [SETUP].  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
V-CHIP  
3 Enter the password.  
• Use [the Number buttons] and enter the  
You can block certain programming inappropriate for  
children. This block can be released by entering a  
password.  
4-digit number.  
V-Chip  
INPUT  
POWER  
SLEEP  
SELECT  
Enter password.  
1
4
7
2
5
8
0
3
6
9
PIN Code  
BACK Back  
AUDIO  
STILL  
• When you have not set up your password,  
enter 0000.  
• When the password is correct, the following  
“V-Chip” screen is displayed.  
-
SCREEN  
MODE  
SETUP  
A
V-Chip  
MPAA Rating  
ENTER  
MPAA Rating  
INFO  
TV Rating  
BACK  
B
C
TV Rating  
New Password  
New Password  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
See the following description for setting each  
item.  
A
MPAA Rating  
4 Display the “MPAA Rating” screen.  
K
L
• Using [ / ], select “MPAA Rating”.  
V-Chip  
MPAA Rating  
2 Select “DETAIL” and press [ENTER].  
TV Rating  
New Password  
K
L
• Using [ / ], select “V-chip”.  
Detail  
Closed Caption  
V–chip  
Auto  
HDMI Audio  
• Press [ENTER].  
V-Chip  
X
NC-17  
R
PG-13  
PG  
G
• Press [ENTER].  
The password entry screen is displayed.  
NR  
BACK  
V-Chip  
ENTER  
Select  
View/Block  
Back  
Enter password.  
PIN Code  
BACK Back  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
5 Set “MPAA Rating”.  
5 Set “TV Rating”.  
K
L
• Using [ / ], select the rating.  
K
L
• Using [ / ], select the rating.  
• Press [ENTER] and set to “View” or “Block”.  
• Press [ENTER] and set to “View” or “Block” for  
V-Chip  
the rating without sub categories.  
X
NC-17  
R
V-Chip  
PG-13  
PG  
G
FV  
V
S
L
D
TV-MA  
TV-14  
TV-PG  
TV-G  
NR  
BACK  
ENTER  
Select  
View/Block  
Back  
TV-Y7  
TV-Y  
BACK  
ENTER  
Select  
View/Block  
Back  
6 To exit the setup, press [SETUP].  
• For the rating with sub categories,  
<Selection>  
X :  
NC-17 :  
R :  
<Rating Category Explanations>  
K
L
press [ / / s / B] and select the rating. Then  
press [ENTER] and set to “View” or “Block”.  
V-Chip  
Mature audience only  
No one under 17 admitted  
Restricted; under 17 requires  
accompanying parent or adult  
guardian  
FV  
V
S
L
D
TV-MA  
TV-14  
TV-PG  
TV-G  
PG-13 :  
PG :  
G :  
Unsuitable for children under 13  
Parental Guidance suggested  
General Audience  
TV-Y7  
TV-Y  
BACK  
ENTER  
Select  
View/Block  
Back  
NR :  
No Rating  
6 To exit the setup, press [SETUP].  
NOTES:  
<Selection>  
TV-MA :  
TV-14 :  
<Rating Category Explanations>  
• When you select a rating and set it to “Block”, the higher  
ratings will be blocked automatically. The lower ratings will  
be available for viewing.  
Mature audience only  
Unsuitable for children under 14  
Parental Guidance suggested  
General Audience  
• When you set “X” to “View”, all ratings turn to “View”  
automatically.  
TV-PG :  
TV-G :  
TV-Y7 :  
Appropriate for children 7 and  
older  
B
TV Rating  
TV-Y :  
Appropriate for all children  
4 Display the “TV Rating” screen.  
K
L
• Using [ / ], select “TV Rating”.  
<Selection>  
<Rating Sub Category Explanations>  
Fantasy Violence  
Violence  
Sexual Situation  
Coarse Language  
Suggestive Dialogue  
V-Chip  
FV :  
V :  
S :  
L :  
MPAA Rating  
TV Rating  
New Password  
D :  
NOTES:  
• Press [ENTER].  
• When you select a rating and set it to “Block”, the higher  
V-Chip  
ratings will be blocked automatically. The lower ratings will  
be available for viewing.  
• When you set “TV-MA” to “View”, all ratings turn to “View”  
automatically.  
FV  
V
S
L
D
TV-MA  
TV-14  
TV-PG  
TV-G  
TV-Y7  
TV-Y  
BACK  
ENTER  
Select  
View/Block  
Back  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
C
New Password  
4 Display the “New Password” screen.  
K
L
• Using [ / ], select “New Password”.  
V-Chip  
MPAA Rating  
TV Rating  
New Password  
• Press [ENTER].  
5 Change the password.  
• Use [the Number buttons] on the remote con-  
trol and enter the NEW 4-digit password.  
• Enter password again in “Confirm password”  
space.  
V-Chip  
Enter password.  
Confirm password.  
PIN Code  
BACK Back  
6 To exit the setup, press [SETUP].  
NOTES:  
• Make sure to enter the exact same new password as the  
“Confirm password.”. If they are different, the space is  
cleared for reentering.  
• Your password will be erased and return to the default  
(0000) when a power failure occurs or when you turn off the  
power using a wall switch. If you forget the password,  
unplug the power cord for 10 seconds to restore the pass-  
word to 0000.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
HDMI AUDIO  
Set the method of sound input for HDMI jack.  
STILL  
0
SCREEN  
MODE  
SETUP  
ENTER  
INFO  
BACK  
1 Display the setup screen.  
• Press [SETUP].  
The following setup screen appears.  
2 Select “DETAIL” and press [ENTER] to confirm.  
K
L
• Using [ / ], select “HDMI Audio” and press  
[ENTER] to confirm.  
Detail  
Closed Caption  
V–chip  
Auto  
HDMI Audio  
3 Switch the HDMI Audio.  
K
L
• Using [ / ], select the desired HDMI Audio,  
then press [ENTER].  
Detail  
Closed Caption  
V–chip  
HDMI Audio  
Auto  
Digital  
Analog  
• Select “Auto” if you connected to both digital  
device with HDMI jack and analog device for  
audio sources. Digital audio input signal has  
priority in this setting.  
• Select “Digital” if you connected to digital  
device with HDMI jack for digital audio input  
signal.  
• Select “Analog” if you connected to analog  
device with analog jacks for analog audio input  
signal.  
4 To exit the setup, press [SETUP].  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
ISCELLANEOUS  
M
TROUBLESHOOTING GUIDE  
Before calling for service, please refer to the following information.  
Symptom  
No power  
Remedy  
• Be sure the power cord is connected to outlet.  
• If a power failure occurs, unplug the power cord for 30 minutes  
to allow the unit to reset itself.  
No picture or sound  
• Check if the power is on.  
• Check the outlet connection.  
• Check the antenna or cable connection to the main unit.  
• When the outside antenna is used, check the wire condition and  
connection.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
• Turn off the power and wait for about 1 minute, then turn it on  
again.  
No color  
• Check the antenna or cable connection to the main unit.  
• When the outside antenna is used, check the wire condition and  
connection.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
• Adjust the Color in the setup screen.  
Sound OK, picture poor  
• Check the antenna or cable connection to the main unit.  
• When the outside antenna is used, check the wire condition and  
connection.  
• Electrical interference from nearby appliances may affect picture  
quality.  
• Adjust Contrast and Brightness in the setup screen.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Picture distorted  
Weak picture  
• When the outside antenna is used, check the wire condition and  
connection.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
• Check the antenna or cable connection to the main unit.  
• When the outside antenna is used, check the wire condition and  
connection.  
• Adjust Contrast and Brightness in the setup screen.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Lines or streaks in picture  
• When the outside antenna is used, check the wire condition and  
connection.  
• Electrical interference from nearby appliances may affect picture  
quality.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Picture blurred  
• When the outside antenna is used, check the wire condition and  
connection.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Ghosts in picture  
• Check the antenna or cable connection to the main unit.  
• When the outside antenna is used, check the wire condition and  
connection.  
• Electrical interference from nearby appliances may affect picture  
quality.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Bars on screen  
• When the outside antenna is used, check the wire condition and  
connection.  
• Electrical interference from nearby appliances may affect picture  
quality.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
Symptom  
Picture rolls vertically  
Remedy  
• When the outside antenna is used, check the wire condition and  
connection.  
• Electrical interference from nearby appliances may affect picture  
quality.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Different color marks on screen  
Poor reception on some channels  
• Move your TV away from nearby electric appliances. Turn off the  
power and wait 30 minutes before turning it back on.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
• Check the antenna or cable connection to the main unit.  
• When the outside antenna is used, check the wire condition and  
connection.  
• Electrical interference from nearby appliances may affect picture  
quality.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
Picture OK, sound poor  
• Electrical interference from nearby appliances may affect picture  
quality.  
• View other TV channels. The problem might be limited to the  
broadcasting station.  
No reception of digital signals  
•
Make sure Autoscan has been completed (Refer to “AUTOSCAN” on  
page 13). Autoscan must be completed when you set up your TV for  
the first time or move it to a location where previously unavailable  
channels are broadcast.  
• The selected channel may not be broadcasting.  
• When Autoscan is interrupted, some channels will not be  
received. Make sure to complete Autoscan in the setup screen.  
Channel changes automatically  
Remote Control doesn’t work  
•
Many digital channels have alternate channel numbers. TV changes the  
numbers automatically to the ones signifying the broadcasting stations.  
These are the numbers used for analog broadcasts.  
• Check the antenna or cable connection to the main unit.  
• Check the batteries of the remote control.  
• Check if there is an obstacle between the sensor and the  
remote control.  
• Test the signal output. If OK, there might be remote sensor trou-  
ble. (Refer to “IR SIGNAL CHECK” on page 34.)  
Problems with Closed Caption Feature  
• Closed captioning production companies may broadcast pro-  
grams without correcting the misspelling in a live broadcast.  
Misspelled captions are displayed.  
•
Captions that are delayed a few seconds behind the actual dialogue  
are common for live broadcasts. Most captioning production compa-  
nies can display a dialogue to a maximum of 220 words per minute. If  
a dialogue exceeds that rate, selective editing is used to ensure that  
the captions remain up-to-date with the current TV screen dialogue.  
Captions are not entirely displayed, or  
captions are delayed behind the dia-  
logue.  
• Interference from buildings or weather conditions may cause  
captioning to be incomplete.  
• Broadcasting station may shorten the program to insert adver-  
tisement. The closed caption decoder cannot read the informa-  
tion of the shortened program.  
Captions are displayed as a white  
box.  
No caption is displayed in the Closed  
Caption-supported program.  
• The videotape may be illegally copied, or the caption signal  
might not have been read during copying.  
No caption is displayed when playing  
the videotape containing captions.  
• “Text” mode is selected for caption. Select “CC1”, “CC2”, “CC3”,  
“CC4” or “Off”.  
Black box is displayed in the screen.  
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels  
may appear as a fixed point of blue, green or red. This is not to be considered a defect in the LCD screen.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
GLOSSARY  
ATSC  
HDMI (High-Definition  
Multimedia Interface)  
Interface that supports all uncom-  
pressed, digital audio/video formats  
including set-top box, DVD player or  
digital television, over a single cable.  
High Definition TV (HDTV)  
Ultimate digital format that produces  
high resolution and high picture quality. nel. This audio channel is used as  
LPCM  
Password  
Acronym that stands for Advanced  
Television Systems Committee and  
the name of the digital broadcasting  
standards.  
A stored 4-digit number that  
allows access to parental control  
features.  
SAP  
Aspect ratio  
(Secondary Audio Program)  
Second-audio channel delivered  
separately from main-audio chan-  
The width of a TV screen relative  
to its height. Conventional TVs are  
4:3 (in other words, the screen is  
almost square); widescreen mod-  
els are 16:9 (the screen is almost  
twice as wide as its height).  
an alternate in bilingual broad-  
casting.  
Standard Definition TV (SDTV)  
Standard digital format that is sim-  
ilar to the NTSC picture quality.  
S-Video  
Offers higher quality images by  
delivering each signal, color (c)  
and luminance (y) independently  
of each other through separate  
cables.  
(Linear Pulse Code Modulation)  
LPCM is a format that can have  
up to 8 channels of audio. It is  
mainly used in music production.  
The format samples and captures  
analog signals and transforms  
them into digital signals without  
compressing the sound data.  
Component video  
This is a video signal format that  
conveys each of three principal  
colors of light (red, blue and  
green) through different signal  
lines. This allows the viewers to  
experience picture colors as origi-  
nal as it is. There are several sig-  
nal formats, including Y / Pb / Pr  
and Y / Cb / Cr.  
NTSC  
Acronym that stands for National  
Television Systems Committee  
and the name of the current ana-  
log broadcasting standards.  
Dolby Digital  
The system developed by Dolby  
Laboratories to compress digital  
sound. It offers stereo sound (2ch)  
or multi-channel audio.  
MAINTENANCE  
CABINET CLEANING  
• Wipe the front panel and other exterior surfaces of  
the TV with a soft cloth immersed in lukewarm  
water and wrung dry.  
IR SIGNAL CHECK  
If the remote control isn’t working properly, you can  
use an AM radio or digital camera (including a cellu-  
lar phone with built-in camera) to see if it is sending  
out an infrared signal.  
• Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the TV. Such chemicals may  
cause damage and discoloration to the exposed  
surfaces.  
• With an AM radio:  
Tune the AM radio station to a  
non-broadcasting frequency.  
Point the remote control towards  
it, push any button and listen. If  
the sound from the radio flutters,  
it is receiving the remote control’s  
infrared signal.  
LCD CLEANING  
Wipe the LCD of the TV with a soft cloth. Before  
cleaning the LCD, disconnect the power cord.  
SERVICING  
• With a digital camera (including built-  
in cell phone cameras):  
Should your unit become inoperative, do not try to  
correct the problem yourself. There are no user ser-  
viceable parts inside. Turn off the TV, unplug the  
power cord and call our toll free customer support  
line found on the cover of this manual to locate an  
authorized service center.  
Point a digital camera towards the  
remote control. Push any button on  
the remote control and look through  
the digital camera. If the infrared light  
appears through the camera, the  
remote control is working.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
PECIFICATIONS  
S
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATION  
Television System:  
ATSC  
Sound Output:  
5W, 8 ohm x 2  
NTSC-M  
TV Standard  
OTHER SPECIFICATIONS  
Closed Caption  
System:  
Remote Control:  
Digital encoded  
infrared light system  
§15.119/FCC (Analog CC)  
§15.122/FCC (Digital CC)  
Operating  
Temperature:  
Channel Coverage (ATSC/NTSC)  
5°C to 40°C  
(41°F to 104°F)  
VHF:  
UHF:  
CATV:  
2 ~ 13  
14 ~ 69  
2 ~ 13, A ~ W,  
W+1 ~ W+94,  
Power Requirements: AC120V, 60Hz  
Power Consumption  
(Maximum):  
LCD:  
205W  
A-5 ~ A-1, 5A  
37" wide XGA panel  
(1,366 x 768 pixels)  
<Without stand>  
H : 26-9/16" (674mm)  
W: 37-5/16" (948mm)  
D : 4-12/16" (120mm)  
<With stand>  
H : 28-5/16" (718.5mm)  
W: 37-5/16" (948mm)  
D : 12-13/16" (325mm)  
52.8 lbs. (24.0kg)  
Tuning System:  
Channel Access:  
Channel frequency  
synthesized tuning system  
Direct access keyboard,  
Programmable scan,  
and Up/down  
Dimensions:  
Terminals  
Antenna Input:  
VHF/UHF/CATV  
75 ohm unbalanced  
(F-type)  
Mini DIN 4-pin jack x 2  
RCA jack x 2  
S-Video Input:  
Video Input:  
Audio Input:  
Weight:  
RCA jack (L/R) x 4  
Component Video/Audio Input:  
One pin jack (Y) / 1Vpp x 2  
Two pin jacks (Pb/Pr) / 700mVpp x 4  
RCA jack (L/R) x 4  
HDMI / Audio Input:  
HDMI jack  
RCA jack (L/R) x 2  
Coaxial Digital Audio Output:  
One pin jack, 500mVpp  
Analog Audio Output:  
RCA jack (L/R) x 2  
Stereo Sound System Speaker  
• Designs and specifications are subject to change without notice and without our legal obligation.  
• If there is a discrepancy between languages, the default language will be English.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EN  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship  
as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Certain parts and LCD image burn-in are excluded from this warranty.  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of  
original retail purchase.  
LABOR:  
LIMITS AND EXCLUSIONS:  
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR  
OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO  
OBTAIN SERVICE UNDER THIS WARRANTY.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or  
if service was attempted by an unauthorized service center. This limited warranty does not apply to any product not  
purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does  
not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL,  
INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE  
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES,  
EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES  
INCLUDING THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE  
HEREBY DISCLAIMED BY FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES.  
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.  
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.  
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO  
PROOF OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIRS COSTS WILL  
BE CHARGED.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM  
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION  
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:  
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original packaging  
or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI CORP. will not  
reimburse you for any service done by unauthorized service providers without prior written approval.  
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries,  
please contact us at :  
FUNAI CORPORATION  
Customer Service  
Tel :1-800-968-3429  
http://www.SylvaniaConsumerElectronics.com  
19900 Van Ness Avenue, Torrance, CA 90501  
Printed in China  
1EMN21968A  
L5007UH / L5003UD ★★★  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Shure Headphones VP83 User Manual
SIIG Computer Hardware 04 0629A User Manual
Soleus Air Air Conditioner KC 45H User Manual
Sony Portable CD Player MDX CA580 User Manual
SoundMax Home Theater System SM CDM1042 User Manual
Star Micronics Network Card IFBD HW03 04 User Manual
Sunbeam Blender 250 22 User Manual
Sunfire Speaker True Subwoofer Signature and Standard Version User Manual
Sun Microsystems Network Router 4500 3 User Manual
Sunrise Medical Personal Lift B684DC User Manual