WWW.SHARKCLEAN.COM
LIGHT & EASY™ STEAM MOP
S3250 11
OWNER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd
1
10-05-27 9:58 AM
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only
11. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. Do not
use extension cords or outlets
with inadequate current carrying
capacity.
21. Extreme caution should be
exercised when using this
appliance to clean stairs.
1. Use the system only for its
WHEN USING YOUR SHARK®
intended use.
STEAM MOP, BASIC SAFETY
22. Never use steam mop without
micro-fiber pad attached.
2. DO NOT use outdoors.
PRECAUTIONS SHOULD ALWAYS
3. DO NOT leave the appliance
23. Keep your work area well lit.
BE FOLLOWED, INCLUDING THE
12. DO NOT put any objects into
openings. Do not use with any
opening blocked.
unattended when plugged in.
24. Store steam mop indoors in a cool,
dry place.
Always unplug the power cord
from the electrical outlet when not
in use and before servicing.
FOLLOWING:
13. DO NOT put hands or feet under
25. To avoid circuit overload, do not
operate another appliance on the
same socket (circuit) as the steam
cleaner.
WARNING:
TO REDUCE
the steam mop. Unit gets very hot.
4. DO NOT allow the appliance to be
used as a toy. Close attention is
necessary when used by or near
children, pets or plants.
THE RISK OF FIRE, ELECTRIC
14. Use ONLY on flat, stable horizontal
surfaces. Do not use on walls,
SHOCK OR INJURY READ ALL
INSTRUCTIONS BEFORE USING
counters, windows, chairs or tables.
26. If an extension cord is absolutely
necessary, an extension cord rated
a minimum of 15 ampere, 14 gage
cord should be used. Cords rated
for less amperage may overheat.
Care should be taken to arrange
cord so that it cannot be pulled or
tripped over.
5. Use only as described in this
manual.
YOUR LIGHT & EASY™.
15. DO NOT use on leather, wax
polished furniture or floors,
DANGER OF SCALDING.
Please use caution when using
the steam mop. The steam emitted
from the openings is very hot.
synthetic fabrics, velvet or other
delicate, steam sensitive materials.
6. Use only manufacturer’s
recommended accessories.
16. DO NOT add cleaning solutions,
scented perfumes, oils or any other
chemicals to the water used in this
appliance as this may damage the
unit or make it unsafe for use. If
you live in a hard water area, we
recommend using distilled water in
your steam mop.
7. DO NOT operate the appliance
with a damaged plug or cord,
or if the unit has been dropped,
damaged left outdoors or dropped
into water. To avoid the risk of
electric shock, do not disassemble
or attempt to repair the appliance
on your own. Return the appliance
to EURO-PRO Operating LLC (see
warranty) for examination and
repair. Incorrect re-assembly or
repair can cause a risk of electrical
shock or injury to persons when
the appliance is used.
27. DO NOT leave unattended when
the system is connected to a power
supply or electrical outlet. Turn off
all controls before unplugging the
unit.
POLARIZED PLUG:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, this appliance has a
polarized plug (one blade is
wider than the other). As a safety
feature, this plug will fit into a
polarized outlet only one way. If
the plug does not fit fully into the
outlet, reverse the plug. If it still
does not fit, contact a qualified
electrician. Do not attempt to
defeat this safety feature.
28 DO NOT store unit with damp
or wet micro-fiber cleaning pad
attached. Never leave the steam
mop in one spot on any surface
for any period of time with a damp
or wet micro-fiber cleaning pad
attached as this will damage your
floors
17. When in use, NEVER turn the
appliance over or on its side.
NEVER DIRECT STEAM TOWARDS
PEOPLE, ANIMALS OR PLANTS.
18. Carefully remove the micro-
fiber pad immediately after you
have unplugged and allowed the
product to cool.
8. To protect against a risk of electric
shock, DO NOT immerse the steam
mop into water or any other liquids.
WARNING: Your steam mop
is designed to clean hard floor
surfaces that will withstand high
heat. Do not use on unsealed wood
or unglazed ceramic floors. On
surfaces that have been treated
with wax or some no wax floors,
the sheen may be removed by
the heat and steam action. It is
always recommended to test an
isolated area of the surface to be
cleaned before proceeding. We also
recommend that you check the use
and care instructions from the floor
manufacturer.
19. When cleaning the steam mop,
unplug the power cord from the
electrical outlet and clean with a
dry or damp cloth. Do not pour
water or use alcohol, benzene or
paint thinner on the unit.
9. DO NOT handle plug or steam
mop with wet hands or operate
appliance without shoes.
10. DO NOT pull or carry by power
cord, use power cord as handle,
close a door on the power cord, or
pull the power cord around sharp
edges or corners. Keep power cord
away from heated surfaces.
20 To reduce the risk of fire, DO NOT
use a flammable or combustible
liquid to clean a floor.
TOLL FREE: 1-800-798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 2-3
10-05-27 9:58 AM
Quick Start
fig. 5
fig. 3
fig. 4
fig. 1
fig. 2
ASSEMBLE
FILL
STEAM CLEANING
4 Plug in the mop. Wait 30
BACKSAVER
1
Fit together the extension tubes
as shown in the illustration.
(fig. 1)
3
Remove the cap to fill the
water tank. Use the filling flask
and funnel to fill the tank with
water to the “MAX” fill line.
Replace the water tank cap.
(fig. 3)
5
Use the Shark® Light &
Easy™ with backsaver
benefit to access tight
areas. Press the release
button on the handle
to lock the Light &
seconds for the unit to heat up
and the steam to be ready.
2
Place the micro-fiber cleaning
pad underneath the mop head,
with quick fastener strips facing
up. Simply press the mop to the
pad to attach it. (fig. 2)
Push the handle toward the
mop head in a pumping motion.
Customize steam output by slow
or fast mopping with a forward
and backward motion. (fig. 4)
Easy™ Steam Mop in the
backsaver position. Press
the release button on the
handle again to straighten
the handle. (fig. 5)
TOLL FREE: 1-800-798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 4-5
10-05-27 9:58 AM
Contents
GETTING STARTED.................................................................2
USING YOUR STEAM MOP...................................................6
USING YOUR ACCESSORIES...............................................9
STORAGE AND CARE OF YOUR STEAM MOP ..........10
TROUBLESHOOTING ............................................................12
WARRANTY AND REGISTRATION...................................13
Thank you for
purchasing
the Shark®
™
Light & Easy
Steam Mop.
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 1550 Watts
Water
Capacity: 250 ml (8 oz.)
TOLL FREE: 1-800-798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 6-1
10-05-27 9:58 AM
English
Getting Started
When assembling your steam mop there
may be a little water in or around the
water tank. This is because we test all
our steam mops 100% before you
buy them, so you get a quality
Shark® Light & Easy™ Steam Mop.
c
b
a
d
e
f
fig. 1
fig. 2
g
h
a Upper Handle Tube with Backsaver
benefit
ASSEMBLY
3 Insert the assembled handle piece
into the steam mop base. Push the
tube base together until you hear a
click. (fig. 2)
IMPORTANT: Never use the Light &
1
Remove all the parts from the
package. Verify all the listed parts
are included.
Easy™ Steam Mop without attaching
a micro-fiber cleaning pad to avoid
damage to your floor and mop.
b Lower Handle Tube
c Steam Mop Base
2 Slide the Upper Handle Tube (the
tube with the handle) into the Lower
Handle tube (the short tube). Push
the two extension tubes together
until you hear them click into place.
(fig. 1)
d 1 All-Purpose Cleaning Pad and
1 Heavy Duty Cleaning Pad
e Filling Flask
f Funnel
g Fresh Breeze Scent
h Grooming Carpet Glider
2
TOLL FREE: 1-800-798-7398
3
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 2-3
10-05-27 9:58 AM
English
Getting Started
Your micro-fiber cleaning
pads should be replaced
every 3 months to maximize
cleaning performance.
fig. 2
fig. 2
fig. 3
fig. 1
ATTACHING THE MICRO-FIBER PAD
USING THE FRESH BREEZE SCENT
To add a light, clean fragrance to the
room, use the Fresh Breeze scented
pad spray.
FILLING THE WATER TANK
2 A filling flask and funnel are included
with your Light & Easy™ Steam Mop
to make filling the water tank easy.
Fill the flask with water and use the
funnel to pour it into the tank. Keep
the water level under the “MAX” fill
line. (fig. 4)
1
Place the micro-fiber cleaning pad
on the floor with the quick fastener
strips facing up. Place the Light &
Easy™ Steam Mop on the top of the
pad to attach. (fig. 1)
IMPORTANT: Unplug the Light &
Easy™ Steam Mop before filling the
water tank with water. (fig. 3)
1
Apply 1-2 mists to the back side
(mesh side) of the pad. (fig. 2)
1
Remove the water tank cap by
turning it counter-clockwise to the
unlocked position. (fig. 4)
2 Apply the pad to the steam pad
and mop as usual. The steam will
activate the mist leaving you with a
fresh fragrance for the room.
IMPORTANT: Only add water to
the tank. Chemicals or cleaning
solutions may be unsafe or cause
damage.
3 Replace the water tank cap and turn
it clockwise to the locked position.
IMPORTANT: DO NOT apply to the
side of the pad that contacts the
floor surface. Not for use on marble
floors.
Replacement micro-fiber pads are
by calling 1-800-798-7398.
4
TOLL FREE: 1-800-798-7398
5
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 4-5
10-05-27 9:58 AM
English
Using Your Light & Easy™ Steam Mop
When you use your steam mop for the
first time or if you have not used the unit
in awhile, it may take a minute or two
for the water to travel through the pump
and into the heater to create steam. Get
it started by pumping the handle a few
times. If you have waited a few minutes
and you still do not see any steam,
reference the troubleshooting section
on page 12.
™
If your Light & Easy Steam
Mop stops steaming, it could
be out of water. Unplug the
power cord from the electrical
outlet and refill the water tank
at anytime.
1
fig. 1
fig. 4
fig. 2
fig. 3
fig. 5
IMPORTANT: Your steam mop needs
water to make steam! Never use
your steam mop without water in the
tank.
1
Pull and twist the quick release
cord holder to unwrap the power
cord completely. (fig. 1) Plug into
a 120-volt electrical outlet. (fig. 2)
The “On” light will turn blue. If the
light does not turn on, reference the
troubleshooting section on page 12.
(fig. 3)
2 Wait 30 seconds for the boiler to
heat the water. Pump the handle
a few times to prime the pump,
activate steam and moisten the
micro-fiber pad. (fig. 4)
3 Mop with a forward and backward
motion to customize steam output
automatically. (fig. 5)
Sweep or vacuum your floors prior
to cleaning with your Light & Easy™
Steam Mop.
great quick cleaning products to
complement your Light & Easy™
Steam Mop, such as the Shark®
Cordless Stick Vac.
6
TOLL FREE: 1-800-798-7398
7
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 6-7
10-05-27 9:58 AM
English
Using Your Light & Easy™ Steam Mop
Using Your Accessories
The Light & Easy™ Steam Mop
will not pick-up solid particles
or hair from carpets or
areas rugs, but it is great for
deodorizing and freshening
carpet surfaces against
tough odors.
fig. 1
fig. 2
fig. 3
1
Clean under furniture and tight
areas using the Shark® Backsaver™
locking handle. Press the handle
release button and apply slight
pressure to bend the handle. The
Shark® Backsaver™ joint will lock at
a perfect, access-maximizing angle.
(fig. 1)
GROOMING CARPET GLIDER
The Light & Easy™ Steam Mop is
versatile. The carpet glider freshens
and deodorizes carpets and area
rugs with the power of steam.
USING THE GROOMING
CARPET GLIDER
2 Plug in the steam mop and begin
freshening and grooming your carpet
by pushing the mop and glider back
and forth to release steam. (fig. 3)
When finished, unplug the Light &
Easy™ Steam Mop and store it as you
would normally.
ATTACHING THE CARPET GLIDER
Set the grooming carpet glider on
the carpet with the grooming bumps
facing down. Place the mop head,
with the All-Purpose micro-fiber pad
attached, on top of the carpet glider.
The steam mop will rest on top of the
glider. (fig. 2)
1
2 Press the release button on the
handle again to straighten.
NOTE: We recommend using the
All-Purpose pad for optimal glider
performance.
8
TOLL FREE: 1-800-798-7398
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 8-9
10-05-27 9:58 AM
English
Care of Your Light & Easy™ Steam Mop
Care of Your Light & Easy™ Steam Mop
fig. 5
fig. 1
fig.3
fig.2
fig. 6
AFTER USE AND STORAGE
4 To store the cooled Shark® Light &
Easy™ Steam Mop, hang on a large
hook. (fig. 3)
CARE OF YOUR MICRO-FIBER
CLEANING PAD
ORDERING REPLACEMENT PARTS
1
When you have finished using the
Light & Easy™ Steam Mop, unplug
the cord from the outlet and place
the mop into the upright position
(fig. 1) and let the unit cool 2-3
minutes. Release steam by pumping
the handle several times.
To order additional parts and
accessories, feel free to contact us at
www.sharkclean.com or call
1-800-798-7398.
1
Wash pads in warm water. Wash
separately from other laundry. Only
use liquid detergent (no powder
detergent). Do not use fabric
softeners. Line dry or dry on a low
dryer setting. (fig. 5)
NOTE: If you want to store the
Light & Easy™ Steam Mop standing
upright, make sure it is leaning
against a wall for added support and
safety. Always store your Shark®
Light & Easy™ Steam Mop with the
micro-fiber cleaning pad removed.
Store away from children and high
traffic areas.
NOTE: Some parts may be available
at your local retailer.
Contact EURO-PRO customer service at
1 800-798-7398 for any other servicing.
2 Carefully separate micro-fiber
cleaning pad from steam mop,
avoiding contact with the hot pocket
or dirt. (fig. 2)
2 If there are loose threads on the
pad carefully cut the threads with
scissors. Do not pull on them or cut
at the base. (fig. 6)
3 Empty the water tank before storage.
Remove the water tank cap and
empty the tank over a sink. Replace
the water cap.
IMPORTANT: The micro-fiber
cleaning pad may be very hot
from the steam. Use caution when
removing. Let the unit cool for 2-3
minutes.
10
TOLL FREE: 1-800-798-7398
11
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 10-11
10-05-27 9:58 AM
English
Trouble Shooting
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
PROBLEM
POSSIBLE REASONS & SOLUTIONS
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
Your steam-mop should be securely plugged into a
120V AC electrical outlet only.
The Light & Easy™
Steam Mop
will not turn-on.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and a check payable to EURO-PRO
Operating LLC in the amount of $ 9.95 to cover the cost of return shipping and handling must be
included. *
Check your fuse or breaker.
If your unit still does not work, call 1-800-798-7398.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
Light & Easy™
Steam Mop will not
make steam.
Is there water in the water tank? If not, add water to your
Steam Mop following instructions on page 5.
Light & Easy™
Steam Mop leaves
water on the floor.
Is your micro-fiber cleaning pad too wet? Unplug your
Steam Mop and change the micro-fiber cleaning pad.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any,
is limited to the specific obligations expressly assumed by it under the terms of the limited
warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential
damages of any nature whatsoever. Some states/provinces do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
Do not leave your steam-mop on the floor with a damp or
wet cleaning pad.
Light & Easy™
Steam Mop left
white spot on
the floor.
Do you have hard water? If you do, you might want to
switch to distilled water.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
Make sure the water is securely on the water tank.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with the item. We recommend you insure the package (as damage in shipping
is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
The pad might be dirty, change the pad.
If you washed the pocket with powder detergent, then the
pad may have residual detergent left on it. Wash it again
with liquid detergent.
If you are cleaning in a kitchen area where there might be a
build-up of grease, use a de-greasing agent such as an all-
purpose cleaner or dish soap and paper towels to clean the
area first.
OWNERSHIP REGISTRATION CARD FOR
Floors are cloudy,
streaky or spotty
after steaming.
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
You might have left the mop in the same spot for too long.
Do you have hard water? If you do, you might want to
switch to distilled water.
This might be leftover from past cleaners used on the floor
surface. Use the steam mop a few more times and see if
the leftover cloudiness is removed.
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………………............
ADDRESS: ………………………………………………………………………………………………...............
Make sure the steam pad is attached correctly.
Light & Easy™
Steam Mop
is hard to push.
Check to see if the cleaning pad is excessively dirty.
Replace if the pad is too dirty or wet.
S3250 11
DATE OF PURCHASE: …………………….. MODEL: ………………...................................
NAME AND ADDRESS OF STORE: …………………………………………………………………..
12
TOLL FREE: 1-800-798-7398
13
Download from Www.Somanuals.com. All Manuals Search And Download.
S3250_instructions_100526.indd 12-13
10-05-27 9:58 AM
|