®
INFLATABLE BOATS
Including the following Model Series:
Fish Hunter™, Super Caravelle, Caravelle,
Colossus™ and HUI
READ THE FOLLOWING
INSTRUCTIONS AND WARNINGS TO AVOID
DROWNING OR SERIOUS INJURY
WARNING:
• Not a life saving device.
• Not for use by children without adult supervision.
• Always wear an approved Personal Flotation Device
(Life Preserver).
• Do not overload.
• Never tow from another boat or vehicle.
• Use only in water away from debris and obstructions.
• Do not use in high wind, strong currents, open water or
dangerous tides.
• Be familiar with the area you intend to use the boat.
• Never allow diving into or from these boats.
• Never leave in or near water when not in use.
• Know and follow local water safety rules and boating
regulations.
• Use only in protected waters.
• Do not use this product under the influence of alcohol
or drugs.
• Do not over inflate.
• Follow inflation sequence on the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
INFLATION INSTRUCTIONS
CAUTION!
Do not over inflate. Pressurize product to "Inflation Pressure"
stated in the chart for your specific product.
WARNING!
Never use a compressor, CO2 or compressed air to inflate the boat.
Do not let your boat come into contact with sharp, pointed objects.
®
To inflate using any Sevylor QuickPump™ unit:
To begin inflation,
open external
stopper and pull to
extend out.
Attach adapter hose
to inflation end of
QuickPump™ unit.
Insert hose and
turn on.
When fully inflated,
seal valve by
pushing in the pump
nozzle to maintain
seal. Gently back
pump out of valve.
Fully remove adapter
and close external
stopper. Valve should
appear depressed
into itself.
®
To inflate using the Sevylor Dual Action Hand Pump or other
inflation device:
To begin inflation,
open external
stopper and pull to
extend out.
Insert nozzle of
inflation device into
the extended valve
and turn on or begin
pumping.
Fully remove adapter
and close external
stopper.
To close valve:
Push in with
inflation device until
stopper has been
depressed, sealing
internal stopper.
Valve should appear
depressed into itself.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT! Inflate the boat chambers in the following order:
1. Inflate the inside all-around safety chamber.
2. Inflate the floor chamber(s).
3. Inflate the bottom tunnel chambers. (These tubular chambers are
only found on Super Caravelle and Fish Hunter™ models.)
4. Inflate the bustle chamber. (This support chamber positioned at
the stern is found only on the large Super Caravelle models.)
5. Inflate the outside main chamber.
The chambers on the boat will be numbered to indicate order of
inflation also. This order of inflation will ensure the proper volume and
buoyancy of the safety chamber.
Note: To inflate the mini double lock valve, which is used on some of
the Sevylor boat floors and seat bottoms, follow the same inflation
instructions above, using the mini double lock valve adapter. The mini
®
Double Lock™ valve adapter is included with all Sevylor pumps.
The adapter can be purchased from Customer Service by calling
1-800-835-3278 (Part Number 5010000707).
CAUTION!
Water temperature and weather does affect the pressure in
inflatable products. In cold weather your product will lose some
pressure due to the fact the air will contract. If this occurs, you
may want to add a little air to improve your products performance.
However, in hot weather, the air will expand.You must let some air
out to prevent your product from failing due to overpressure. You
should avoid exposing your product to extreme temperatures (hot
or cold).
DEFLATION INSTRUCTIONS
Deflation instructions using
any Sevylor QuickPump™
unit:
Deflation instructions using
the Sevylor Dual Action
Hand Pump:
®
®
Remove adapter hose from inflation end and
attach to opposite deflation end of pump.
Repeat same steps as inflation. This will
draw the air out quickly.
Remove adapter hose from inflation port
and attach to deflation port on pump
handle. Repeat same steps as inflation. This
will draw the air out quickly.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Your boat is NMMA certified using the ABYC standard.
WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)
Persons
Capacity
Maximum Pay-
load Capacity
Inflation
Pressure
Inflation
Pressure
Engine
Persons, Gear,
Motor
Main
Floor
Model #
HUI 100
HUI 200
HUI 400
Persons Only
Max. HP Engine
Chamber(s)
Chamber(s)
(if applicable)
1 Pers. or 190
lbs.
190 lbs.
370 lbs.
650 lbs.
N/A
N/A
N/A
0.4 PSI
0.4 PSI
0.4 PSI
0.4 PSI
0.4 PSI
0.4 PSI
2 Pers. or 370
lbs.
4 Pers. or 650
lbs.
WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)
Persons
Capacity
Maximum Pay-
load Capacity
Inflation
Pressure
Inflation
Pressure
Engine
Persons, Gear,
Motor
(if applicable)
Main
Chamber(s)
Floor
Chamber(s)
Model #
Persons Only
Max. HP Engine
Colossus™
2 Pers. or
435 lbs.
435 lbs.
680 lbs.
840 lbs.
N/A
N/A
N/A
0.5 PSI
0.5 PSI
0.5 PSI
0.5 PSI
0.5 PSI
0.5 PSI
2 Person Boat
Colossus™
3 Person Boat
3 Pers. or
680 lbs.
Colossus™
4 Person Boat
4 Pers. or
840 lbs.
WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)
Persons
Capacity
Maximum Pay-
load Capacity
Inflation
Pressure
Inflation
Pressure
Engine
Persons, Gear,
Motor
(if applicable)
Main
Chamber(s)
Floor
Chamber(s)
Model #
Persons Only
Max. HP Engine
Caravelle
2 Pers. or
300 lbs.
360 lbs.
600 lbs.
700 lbs.
900 lbs.
N/A
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
2 Person Boat
12V Electric
Motor (Sevylor
2000004144)
Caravelle
3 Person Boat
3 Pers. or
550 lbs.
Caravelle
4 Person Boat
4 Pers. or
600 lbs.
3.0 *
3.0 *
Caravelle
5 Person Boat
5 Pers. or
800 lbs.
*
Requires 2000004146 Motor Mount Kit (sold separately)
for motors other than Sevylor 12 Volt Motor, Model
2000004144
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)
Persons
Capacity
Maximum Pay-
load Capacity
Inflation
Pressure
Inflation
Pressure
Engine
Persons, Gear,
Motor
(if applicable)
Main
Chamber(s)
Floor
Chamber(s)
Model #
Persons Only
Max. HP Engine
Fish Hunter™ 3
Person Boat
3 Pers. or
450 lbs.
600 lbs.
700 lbs.
1200 lbs.
900 lbs.
2.0 *
4.0 *
3.0 *
3.0 *
0.9 PSI
0.9 PSI
0.9 PSI
1.5 PSI
0.9 PSI
0.9 PSI
0.9 PSI
N / A
Fish Hunter™ 4
Person Boat
4 Pers. or
650 lbs.
Fish Hunter™ 6
Person Boat
6 Pers. or
900 lbs.
Fish Master™ 4
Person Boat
4 Pers. or
800 lbs.
*
Requires 2000004146 Motor Mount Kit (sold separately)
for motors other than Sevylor 12 Volt Motor, Model
2000004144
WARNING!
Do not exceed the certified maximum capacities under any circumstances!
NMMA (ABYC
Standard)
Persons
Capacity
Maximum Pay-
load Capacity
Inflation
Pressure
Inflation
Pressure
Engine
Persons, Gear,
Motor
(if applicable)
Main
Chamber(s)
Floor
Chamber(s)
Model #
Persons Only
Max. HP Engine
12V Electric
Motor (Sevylor
2000004144)
Super Caravelle
2 Person Boat
2 Pers. or
300 lbs.
360 lbs.
600 lbs.
700 lbs.
1,100 lbs.
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
0.9 PSI
Super Caravelle
3 Person Boat
3 Pers. or
550 lbs.
2.0 *
3.5 *
3.5 *
Super Caravelle
4 Person Boat
4 Pers. or
600 lbs.
Super Caravelle
6 Person Boat
6 Pers. or
900 lbs.
*
Requires 2000004146 Motor Mount Kit (sold separately)
for motors other than Sevylor 12 Volt Motor, Model
2000004144
WARNING!
Do not attempt to mount a motor on any boat that does not state a
Max. HP Engine rating.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SEVYTEST™ GAUGE
®
Some of the Sevylor products are equipped with a Sevytest™
gauge. The Sevytest™ device is a pressure gauge, not an inflation
gauge. The Sevytest™ gauge is found on the side wall, inside the
main chamber(s). The purpose is to show you when to let some air
out after the pressure has increased due to temperature change.
The principle of the Sevytest™ gauge is based on the lengthening of
the PVC under the influence of pressure. Once the boat is properly
inflated, note the position of the Sevytest™ indicator. Then periodical-
ly check the Sevytest™ gauge and let out enough air to keep the test
strip in the same general area. If the Sevytest™ indicator is in the “+”
zone, add pressure to the product. If the Sevytest™ indicator is in “-”
zone, release pressure from the product.
Add
pressure
Maintain
pressure
in this
zone
Release
pressure
®
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS:
•
Follow all local boating regulations and navigation rules.
Familiarize yourself with boating conditions where you plan to
use the boat. Use common sense and caution when operating in
unfamiliar places.
•
•
Observe the maximum weight the boat can carry and do not
overload past this limit. Over-loading jeopardizes the safety of the
occupants.
Be sure all accessories and/or equipment (e.g. oars, life jackets)
are in proper working condition before using the boat. Each
person occupying the boat is to wear an approved Personal
Flotation Device (life preserver).
•
•
Sharp objects are not to be carried in the boat without adequate
protection or storage.
When navigating the boat in any water depth, watch for
submerged or sharp objects that may damage or pierce the
boat’s air chambers.
•
•
Enter the boat from the port (left) or starboard (right) sides - not
from the fore (front) or aft (back) sides.
Never tow with a boat or any other vehicle.
MOTOR MOUNTING
WARNING!
Do not mount a motor on any boat that exceeds the Maximum
Horsepower Rating for your specific boat model.
®
All Sevylor boats that have a Horsepower Rating can accept the
®
Sevylor 12V Trolling Motor, Model 2000004144 without purchasing
any additional mounting hardware. Refer to 12V Trolling Motor
mounting instructions.
Mounting any motor other than the Sevylor 12V Trolling Motor,
Model 2000004144, requires the Sevylor Motor Mount Kit, Model
®
®
2000004146, which is sold separately.
CARE & STORAGE:
•
These boats are made of the highest quality materials and
comply with NMMA (National Marine Manufacturers Association)
regulations. Altering the construction of these boats will void the
limited warranty and could jeopardize the safety of the occupants.
If your boat has been used in salt water, rinse it off with fresh
water as soon as possible.
•
•
Remove tar spots or other soiled areas by using a mild soap and
rinsing with fresh water.
•
•
Be sure your boat is completely dry before storing.
The boats may be stored inflated, but do not place any heavy or
sharp objects on it. Storage is best in a dry room.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Caravelle Models
5 PERSON
Fittings for
Motor Mount
Carry
Handle
Inflated
Floor
Fittings for
12V Motor
DIN Safety
Chamber
4 Oar locks
Double as Handles
Grab Line
Fittings for
Motor Mount
4 PERSON
Carry
Handle
Inflated
Floor
Fittings for
12V Motor
4 Oar locks
Double as Handles
DIN Safety
Chamber
Grab Line
3 PERSON
Fittings for
12V Motor
Inflated
Floor
Grab Line
DIN Safety
Chamber
2 Oar locks
Double as Handles
Fittings for
12V Motor
2 PERSON
Inflated
Floor
Grab Line
DIN Safety
Chamber
2 Oar locks
Double as Handles
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Super Caravelle Models
6 PERSON
Fittings for
Motor Mount
Inflatable
Seat
Carry
Handle
Inflatable
Seat
Fittings for
12V Motor
Grab Line
Exterior Tunnel
Chambers
4 Patented Delrin®
Swivel Oar Locks
DIN Safety
Chamber
Fittings for
Motor Mount
4 PERSON
Carry
Handle
Inflatable
Seat
Fittings for
12V Motor
Grab Line
Exterior Tunnel
DIN Safety
Chamber
4 Patented Delrin®
Swivel Oar Locks
Chambers
3 PERSON
Fittings for
Motor Mount
Carry
Fittings for
12V Motor
Handle
Grab Line
Exterior Tunnel
Chambers
DIN Safety
Chamber
2 Molded
Oar Locks
2 PERSON
Fittings for
12V Motor
Grab Line
Exterior Tunnel
DIN Safety
Chamber
2 Molded
Oar Locks
Chambers
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Colossus™ Models
4 PERSON
4 Air
Chambers
Front
Handle
Grab Line
8 Rope Holders
with Oar Storage
Clips
4 Oar Locks
3 PERSON
Front
Handle
4 Air
Chambers
Grab Line
8 Rope Holders
with Oar Storage
Clips
2 Oar Locks
2 PERSON
Front
Handle
3 Air
Chambers
Grab Line
8 Rope Holders
with Oar Storage
Clips
2 Oar Locks
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Fish Hunter™ Models
6 PERSON
Oar Holders
Inflatable
Seat
Fishing Rod
Holder
Front Fittings
for 12V Motor
Carry
Handle
Fittings
for Motor
Mount
Carry
Handle
Rear Fittings
for 12V Motor
Grab Line
Inflatable
Seat
Exterior Tunnel
Chambers
Gear Bag
Battery
Pouch
4 Swivel
Oar Locks
Fishing Rod
Holder
Chafing
Pads
4 PERSON
Chafing
Pads
Oar Holders
Inflatable
Seat
Fishing Rod
Holder
Front Fittings
for 12V Motor
Carry
Handle
Fittings
for Motor
Mount
Carry
Handle
Rear Fittings
for 12V Motor
Inflatable
Seat
Grab Line
Exterior Tunnel
Chambers
Gear Bag
Fishing
Rod Holder
Battery
Pouch
4 Swivel
Oar Locks
3 PERSON
Oar Holders
2 Swivel
Fishing Rod
Fittings for
Oar Locks
Holder
Motor Mount
and Outboard
Motor up to
2HP and 12V
Motors
Carry
Handle
Carry
Handle
Inflatable
Seat
Grab Line
Chafing
Pads
Exterior Tunnel
Chambers
Gear Bag
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HUI Models
HUI 400
DIN Safety Chamber
Carry
Handle
Inflated
Floor- 2
Chambers
Grab Line
Main Chamber
4 Oar Locks
HUI 200
DIN Safety Chamber
Grab Line
Inflated
Floor- 2
2 Oar Locks
Main Chamber
DIN Safety Chamber
Chambers
HUI 100
2 Oar Locks
Inflated
Floor- 2
Chambers
Grab Line
Main Chamber
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GRAB LINE INSTALLATION:
IMPORTANT: To properly install the inflatable boat’s grab line, first
inflate the boat. Feed the grab line through the eyelets on each of the
rope holders. Then tie the two loose ends in a square knot at the rear
of the boat.
Square Knot
OAR ASSEMBLY:
(for models with oar included)
Join the two shafts together by screwing them together into the
coupler. Attach the blade to the shafts by screwing in into the bottom
of the shaft.
Replacement Part #2000004151
Coupler
Retainer
Ring
Blade
Shaft
Shaft
The assembled oar is to be inserted into the oar locks from the
outside of the boat. The oar retainer ring is then placed onto the top
half of the assembled oar, from the inside of the boat, to prevent the
oar from sliding into the water (see below).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIRING SMALL PUNCTURES
For inadvertent punctures, you can repair them with the included
®
Sevylor repair patch.
INSTRUCTIONS:
1. Thoroughly clean and dry the damaged area. Completely deflate
if an inflatable article.
2. Cut a portion of the patch to cover the puncture, and allow an
additional ¼” on all sides. Always cut a round or oval patch. Never
leave corners.
3. Be sure the spot is completely dry.
4. Peel the backing from the patch.
5. Adhere the patch to the puncture.
6. Using your thumb or finger apply even pressure across the entire
surface of the patch.
®
The Sevylor AirSeal repair kit is also another repair option available
®
(Model # 2000003730 - not included). Sevylor AirSeal is a fast,
reliable repair for vinyl inflatables: air mattresses, toys, pools, boats
as well as rainwear, groundsheets, golf bags, etc.
INSTRUCTIONS:
1. Thoroughly clean and dry the damaged area. Completely deflate
if an inflatable article.
2. When the damage is small (a pin hole or tear under 2 inches)
apply a light coat of AirSeal two or three times. Allow five minutes
to dry between each application.
3. For heavier material, e.g. fabric backed vinyl or a vinyl boat, apply
up to five coats allowing a five-minute drying period between
coats.
4. Ensure the AirSeal is completely dry before resuming use of the
article.
5. When the damage is more extensive, cut a patch (with rounded
corners) using any vinyl material. Generously coat the damaged
area spreading the AirSeal at least 3/8” from the torn edges. Apply
the patch and apply AirSeal to all edges of the patch making a
seal between patch and the item being repaired. Allow the article
to dry at least 10 hours before using.
Contains sufficient material for several small repairs.
AirSeal is intended for use with 100% PVC (poly vinyl chloride) only.
Do not use with any other material.
®
You may purchase the Sevylor repair patch (Model # 2000003731)
®
and Sevylor AirSeal (Model # 2000003730) by calling Coleman
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited 90 Day Warranty
The Coleman Company, Inc. (“Coleman”) warrants that for a period of 90 days from the date
of original retail purchase, this product will be free from defects in material and workmanship.
Coleman, at its option, will repair or replace this product or any component of the product found to
be defective during the warranty period. Replacement will be made with a new or remanufactured
product or component. If the product is no longer available, replacement may be made with a
similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is
not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty
®
performance. Coleman dealers, service centers, or retail stores selling Sevylor products do not
have the right to alter, modify or in any way change the terms and conditions of this warranty.
What This Warranty Does Not Cover
This warranty does not cover normal wear of parts, parts that are not genuine Coleman parts,
®
or damage resulting from any of the following: negligent use or misuse of the product; commercial
use of the product; use contrary to the operating instructions; disassembly, repair or alteration by
anyone other than Coleman or an authorized service center. Further, the warranty does not cover
Acts of God, such as fire, flood, hurricanes and tornadoes. Warranty void if damage to the product
®
results from the use of a part other than a genuine Sevylor part.
COLEMAN SHALL NOT BE LIABLE FOR DEFECTS THAT ARE CAUSED BY THE USE
OF UNAUTHORIZED PARTS OR SERVICE. COLEMAN SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY OR CONDITIONS. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE IS LIMITED IN DURATION TO THE DURATION OF THE ABOVE
WARRANTY OR CONDITIONS. SOME STATES OR JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
How to Obtain Warranty Service
Take the product to an authorized Coleman service center. You can find the nearest authorized
TDD 1-316-832-8707. If a service center is not conveniently located, attach to the product a tag
that includes your name, address, daytime telephone number and description of the problem.
Include a copy of the original sales receipt. Carefully package the product and send either by
courier or insured mail with shipping and insurance prepaid to:
The Coleman Company, Inc.
3600 North Hydraulic
Wichita, KS 67219
The costs of transporting the product to Coleman or an authorized service center for warranty
service is the responsibility of the purchaser.
DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
If you have any questions regarding this warranty please call 1-800-835-3278 or
TDD 1-316-832-8707.
© 2010 The Coleman Company, Inc. All rights reserved.
QuickPump™, Fish Hunter™, Double Lock™ and Colossus™ are trademarks of The Coleman
Company, Inc. Sevylor® is a registered trademark and
is a trademark of Sevca, LLC.
®
3600 North Hydraulic • Wichita, KS 67219 U.S.A.
4010006024 (20100105)
Download from Www.Somanuals.com. All Manuals Search And Download.
|