Connecting Additional Equipment
4-100-519-21
Operating Instructions
KV-20FA210
© 2003 by Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Additional Equipment
WARNING
To reduce the risk of fire or electric shock, do not expose the
TV to rain or moisture.
To reduce the risk of electric shock, do not use
this polarized plug with an extension cord,
receptacle, or other outlet unless the blades can
be fully inserted to prevent blade exposure.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
✍
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
ATTENTION
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
NOTIFICATION
This equipment has been tested and found to comply with
the limits for a Class B digital device pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference with radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
❏
❏
Reorient or relocate the receiving antennas.
Increase the separation between the equipment and
receiver.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
❏
❏
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Note to the CATV Installer
Protecting the TV
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of
cable entry as practical.
❏
To prevent internal heat build-up, do not block the
ventilation openings.
Do not install the TV in a hot or humid place, or in a place
subject to excessive dust or mechanical vibration.
❏
Note on Caption Vision
This television receiver provides display of television closed
captioning in accordance with § 15.119 of the FCC rules.
Use of this television for other than private viewing of
programs broadcast on UHF or VHF or transmitted by cable
companies for the use of the general public may require
authorization from the broadcaster-cable company and/or
program owner.
SAFETY PRECAUTIONS
❏
❏
Operate the TV only on 120 V AC.
One blade of the power plug is wider than the other for
safety purposes and will fit into the power outlet only one
way. If you are unable to insert the plug fully into the
outlet, contact your dealer.
❏
If any liquid or solid object falls into the TV, unplug it and
have it checked by qualified personnel before operating it
further.
Owner’s Record
The model and serial numbers are located on the front cover
of this manual and at the rear of your TV.
CAUTION
Trademarks and Copyrights
When using TV games, computers, and similar products
with your TV, keep the brightness and contrast functions at
low settings. If a fixed (non-moving) pattern is left on the
screen for long periods of time at a high brightness or
contrast setting, the image can be permanently imprinted
onto the screen. Continuously watching the same channel
can cause the imprint of station logos onto the TV screen.
These types of imprints are not covered by your warranty
because they are the results of misuse.
®
ENERGY STAR is a registered mark.
®
As an ENERGY STAR Partner, Sony has
determined that this product or product
®
model meets the ENERGY STAR guidelines
for energy efficiency.
WEGA®, FD Trinitron, Caption Vision, Dynamic Bass Response
System and Steady Sound are registered trademarks of Sony
Corporation.
Licensed by BBE Sound, Inc. under USP 4638258.4482866. BBE and
BBE symbol are trademarks of BBE Sound, Inc.
“WOW and the ( )® symbol are trademarks of SRS Labs,
Inc. WOW technology is incorporated under license from
SRS Labs, Inc.”
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
IMPORTANT SAFEGUARDS
For your protection, please read these instructions
completely, and keep this manual for future reference.
Carefully observe and comply with all warnings, cautions
and instructions placed on the set, or described in the
operating instructions or service manual.
Do not disconnect the antenna or the power cord during a
heavy storm. Lightning may strike while you are holding
the cable or cord, causing serious injury. Turn off your TV
and wait for the weather to improve.
Object and Liquid Entry
Never push objects of any kind into the set
through the cabinet slots as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the set.
WARNING
To guard against injury, the following basic safety
precautions should be observed in the installation, use, and
servicing of the set.
Use
Attachments
Power Sources
Do not use attachments not recommended
by the manufacturer, as they may cause
hazards.
This set should be operated only from
the type of power source indicated on
the serial/model plate. If you are not
sure of the type of electrical power
supplied to your home, consult your
dealer or local power company. For
those sets designed to operate from
battery power, refer to the operating instructions.
Do not place any objects, especially heavy
objects, on top of the set. The object may
fall from the set, causing injury.
Cleaning
Unplug the set from the wall outlet before
cleaning or polishing it. Do not use liquid
cleaners or aerosol cleaners. Use a cloth
lightly dampened with water for cleaning
the exterior of the set.
Grounding or Polarization
This set may be equipped with a polarized alternating current
line plug (a plug having one blade wider than other). This
plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug still fails to fit, contact
your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
If a snapping or popping sound from a TV set
is continuous or frequent while the TV is
operating, unplug the TV and consult your
dealer or service technician. It is normal for
some TV sets to make occasional snapping or
popping sounds, particularly when being
turned on or off.
For the set with a polarized AC power cord plug
This plug will fit into the power outlet
only one way. This is a safety feature.
Installation
If you are unable to insert the plug
Always use two or more people to lift or move the set. The
set is heavy and the bottom surface is flat. Serious injury can
result from trying to move the set by yourself alone, or from
unsteady handling.
fully into the outlet, try reversing the
plug. If the plug still fails to fit, contact
your electrician to have a suitable outlet installed. Do not
defeat the safety purpose of the polarized plug by forcing it in.
Install the set on a stable, level surface.
Alternate Warning
For the set with a three-wire grounding type AC plug
Water and Moisture
Do not use power-line
operated sets near water —
for example, near a bathtub,
washbowl, kitchen sink, or
laundry tub, in a wet
This plug will only fit into a
grounding-type power outlet. This is
a safety feature. If you are unable to
insert the plug into the outlet, contact
your electrician to have a suitable
outlet installed. Do not defeat the
safety purpose of the grounding plug.
basement, or near a
swimming pool, etc.
Accessories
Overloading
Do not place the set on
an unstable cart, stand,
Do not overload wall
tripod, bracket, table,
outlets, extension
or shelf. The set may
cords or convenience
fall, causing serious
receptacles beyond
injury to a child or an
their capacity, since
adult, and serious
this can result in fire
damage to the set. Use
or electric shock.
only a cart or stand recommended by the manufacturer for the
specific model of TV. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer. An
appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to overturn.
Always turn the set off when it is not to be used. When the
set is left unattended and unused for long periods of time,
unplug it from the wall outlet as a precaution against the
possibility of an internal malfunction that could create a fire
hazard.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Additional Equipment
Ventilation
Lightning
The slots and openings in the cabinet and in the back or
bottom are provided for necessary ventilation. To ensure
reliable operation of the set, and to protect it from
overheating, these slots and openings must never be
blocked or covered.
For added protection for this television receiver during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the
receiver due to lightning and power-line surges.
•
•
•
Never cover the slots and openings
with a cloth or other materials.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
Never block the slots and openings
by placing the set on a bed, sofa, rug
or other similar surface.
•
•
When the power cord or plug
is damaged or frayed.
Never place the set in a confined
space, such as a bookcase or built-in
cabinet, unless proper ventilation is
provided.
If liquid has been spilled
into the set or objects have
fallen into the product.
•
Do not place the set near or over a
radiator or heat register, or where it is
exposed to direct sunlight.
•
•
If the set has been exposed to
rain or water.
Power-Cord Protection
Do not allow anything to rest on or roll over the
power cord, and do not place the set where the
power cord is subject to wear or abuse.
If the set has been subject to
excessive shock by being
dropped, or the cabinet has
been damaged.
Antennas
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions
below. An outdoor antenna system should not be located in
the vicinity of overhead power lines or other electric light or
power circuits, or where it can come in contact with such
power lines or circuits.
•
If the set does not operate
normally when following the operating
instructions. Adjust only those controls
that are specified in the operating
instructions. Improper adjustment of
other controls may result in damage and
will often require extensive work by a
qualified technician to restore the set to normal operation.
WHEN INSTALLING AN OUTDOOR ANTENNA
SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP
FROM CONTACTING SUCH POWER LINES OR
CIRCUITS AS CONTACT WITH THEM IS ALMOST
INVARIABLY FATAL.
•
When the set exhibits a distinct change in
performance — this indicates a need for service.
Be sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in USA and
Section 54 of the Canadian Electrical Code in Canada
provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
Servicing
Do not attempt to service the set yourself
since opening the cabinet may expose you
to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Replacement Parts
When replacement parts are required, be
sure the service technician certifies in
writing that he has used replacement
parts specified by the manufacturer that
have the same characteristics as the
original parts. Unauthorized
Antenna Grounding According to the NEC
Antenna Grounding According to the National Electrical
Code, ANSI/NFPA 70.
substitutions may result in fire, electric
shock, or other hazards.
ANTENNA
LEAD IN
WIRE
Safety Check
GROUND
CLAMP
Upon completion of any service or repairs to
the set, ask the service technician to perform
routine safety checks (as specified by the
manufacturer) to determine that the set is in
safe operating condition, and to so certify.
When the set reaches the end of its useful life,
improper disposal could result in a picture
tube implosion. Ask a qualified service
technician to dispose of the set.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ARTICLE 250, PART H)
NEC - NATIONAL ELECTRIC CODE
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introducing the FD Trinitron WEGA® Features......................................................................... 1
About this Manual.......................................................................................................................... 2
Batteries for the Remote Control .................................................................................................. 2
Using the Remote Control
Programming the Remote Control............................................................................................... 5
Manufacturer’s Codes.................................................................................................................... 6
Using your TV Remote Control with Other Equipment........................................................... 7
Connecting Your TV
TV Rear Panel.................................................................................................................................. 9
Dynamic Bass Response System Connection (Subwoofer) .................................................... 11
Using Basic Functions
Using the Menus
How to Access Menus.................................................................................................................. 23
Using the Video Menu ................................................................................................................ 24
Picture Controls Menu (Video menu)........................................................................................ 25
Using the Audio Menu ............................................................................................................... 26
Options (Audio Menu)................................................................................................................. 27
Using the Channel Setup Menu.................................................................................................. 28
Using the Parental Control Menu .............................................................................................. 30
Parental Control...................................................................................................................... 31
United States: Selecting Custom Rating Options............................................................... 33
Canada: Selecting Custom Rating Options......................................................................... 35
Using the Timer Menu ................................................................................................................ 36
Using the Setup Menu................................................................................................................. 37
Other Information
Troubleshooting............................................................................................................................ 39
Specifications................................................................................................................................. 43
Index...................................................................................................................................................... 45
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations on your purchase of the Sony FD Trinitron WEGA®.
®
Introducing the FD Trinitron WEGA Features
Some of the features you will enjoy include:
❏
❏
❏
❏
❏
❏
❏
FD Trinitron Flat CRT — Delivers a picture with uncompromising accuracy and
outstanding image detail via a technologically advanced tube.
Dynamic Bass Response System — Enhances low-frequency sounds with a powerful
subwoofer. New and exclusive from Sony.
Y, PB, PR Inputs — Provides component video inputs for superior picture quality
(480i only).
WOW — Provides a dramatic presence with a full, deep bass sound. When WOW is
enabled, BBE is directly activated to further enhance the audio performance.
BBE — Gives sound more impact by using audio technology to compensate for phase
effects in speakers.
Parental Control (V-Chip) — Helps parents monitor what their children watch on TV by
establishing rating limits.
Favorite Channels — Provides instant access to your favorite channels with the touch of a
button.
❏
❏
XDS — Displays the name and the remaining time of the current program, if available.
Universal Remote Control — Operates your connected cable box, VCR, digital satellite
receiver, or DVD player.
❏
❏
Energy Star® — Meets the Energy Star guidelines for energy efficiency.
Front Panel Controls — Allows access to the on-screen menus without the use of a remote
control.
❏
Front A/V Inputs — Lets you quickly connect video games, camcorders, or stereo/mono
equipment.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
About this Manual
This manual provides instructions to help you enjoy your new TV. It shows you how to
connect to an antenna or cable, cable box, VCR, DVD, satellite receiver, stereo system, or
camcorder. Once your TV is connected, follow the instructions and use the remote control to
access the on-screen menus.
Batteries for the Remote Control
Insert two AA (R6) batteries (supplied) into the remote control using the following illustration
as a guide.
✍ Under normal conditions, batteries will last up to six months. If the remote control does not operate
properly, the batteries might be worn out.
✍ If you will not be using the remote control for an extended period of time, remove the batteries to
avoid possible damage from battery leakage.
Front Panel Menu Controls
The front Audio/Video panel controls allow you to access the menu without the remote
control.
❏
❏
Press
Use the
control.
to display the on-screen menu.
and
buttons on the front Audio/Video panel instead of your remote
❏
Use the
button on the front Audio/Video panel to navigate through the menus, then
select an item. The front panel controls also allow you to change your channels (CH+/-),
adjust the volume (VOL +/-), and change video inputs.
✍ To navigate the menus with your remote control, see “Using the Menus” on page 23.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Remote Control Description
Button
Description
MUTING
Instantly turns off the sound. Press again or press
to restore the sound.
1
SYSTEM OFF
TV/VCR
Powers off all Sony equipment at once (may not
work with older equipment).
2
3
K
L
A
Press when you are finished using a VCR and you
want to switch to the TV Antenna input. Your VCR
power will remain on.
B
C
M
PICTURE MODE
SLEEP
Cycles through the available Video Mode settings.
4
5
Turns the TV off automatically in approximately 15,
30, 45, 60 or 90 minutes. Cancel by pressing until
Sleep Off appears.
N
O
D
E
JUMP
Press to jump back and forth between two channels.
The TV alternates between current channel and the
last channel that was selected.
6
P
Q
Press for a direct selection of Effect settings
(Simulated, WOW, SRS, Off) (see page 26).
7
8
F
G
RESET
Press to return to factory settings while in an on-
screen menu.
R
S
T
VOL (volume)
CODE SET
Press when you want to adjust the volume.
9
q;
Use to program your remote control to operate
connected video equipment (see page 5).
H
POWER
Press when you want to turn connected equipment
on or off.
qa
qs
qd
U
I
J
FUNCTION
Press when you want to control connected
equipment with your remote control.
VCR/DVD
(operating)
Operates VCR or DVD. Use when you want to
operate connected VCR or DVD with your remote
control.
TV/VIDEO
DISPLAY
Press to cycle through available video inputs.
qf
qg
Press once to show current time (if set) and channel
number. Press again to turn DISPLAY off.
MTS/SAP
Cycles through the Multi-Channel TV Sound (MTS)
options: Stereo, Mono, and Auto SAP (Second
Audio Program).
qh
and
Change the channels directly. Press
buttons to select a channel, then press ENTER.
0
9
qj
qk
0
9
ENTER
GUIDE
Brings up the custom guide of your satellite
receiver.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Button
Description
Moves the cursor in the on-screen menus. Press the
arrow buttons to move the cursor. Press the center
button to select or access an option.
ql
MENU
Displays the on-screen menu. Press again to exit the
menu at any time.
w;
wa
CH (channel)
Press when you want to change channels.
✍ If you lose your remote control, see page 40.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Programming the Remote Control
In order to use your remote control with other equipment, you need to program your remote
control. Use the following procedure to program the remote control.
1
Check the list of “Manufacturer’s Codes” on page 6 and find the three-digit code number
for the manufacturer of your component. If more than one code number is listed, use the
number listed first.
2
Press
✍ The
Press
.
and
button will flash when you press
.
3
or
button to indicate the type of component you want to program with
the remote control.
✍ You must do step 4 within 10 seconds of step 3, or you must redo steps 2 and 3.
4
5
6
Use the
Press
0
9 buttons to enter the three-digit manufacturer’s code number.
.
To check if the code number works, aim the TV’s remote control at the component and
press on the green POWER button (VCR/DVD, SAT/CABLE, TV) that corresponds with
that component. If it responds, you are done. If not try using another code listed for that
manufacturer.
✍ If you have problems programming your remote control, see “Troubleshooting” on page 39.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Manufacturer’s Codes
Manufacturer
Olympic
Optimus
Code
309, 308
327
308, 309, 306,
307
305, 304
308, 309
308, 309, 310
308
308, 309, 306
304, 305, 308,
309, 311, 312,
313, 310, 329
309, 330, 328,
335, 324, 338
314
322, 313, 321
330, 335
312, 313, 321,
335, 323, 324,
325, 326
327, 328
315
DVD Players
Manufacturer
Sony
Hitachi
JVC
Magnavox
Mitsubishi
Onkyo
Oritron
Panasonic
Philips
Pioneer
RCA
Samsung
Toshiba
Zenith
Code
751
758
756
757
761
762
759
753
757
752
755
758
754
760
VCRs
Manufacturer
Code
Panasonic
Sony
Admiral
(M. Ward)
301, 302, 303
327
Pentax
Philco
Philips
Pioneer
Quasar
Aiwa
Audio
Dynamic
338, 344
314, 337
Broksonic
Canon
Citizen
319, 317
309, 308
332
RCA/
PROSCAN
Realistic
Craig
302, 332
315
304, 338, 309
341, 312, 309
314, 336, 337
304
Criterion
Curtis Mathes
Daewoo
DBX
Dimensia
Emerson
Sansui
Samsung
Sanyo
Scott
Cable Boxes
Manufacturer
Sony
Code
319, 320, 316,
317, 318, 341
Sharp
Shintom
Signature 2000
(M. Ward)
SV2000
230
222, 223, 224,
225, 226
Fisher
Funai
330, 335
338
Hamlin/Regal
338, 327
Jerrold/G.I./
Motorola
201, 202, 203,
204, 205, 206,
207, 208, 218
227, 228, 229
219, 220, 221
214, 215
General
Electric
329, 304, 309
338
Go Video
Goldstar
Hitachi
322, 339, 340
332
306, 304, 305,
338
Sylvania
308, 309, 338,
310
338
332
314, 336, 337
314, 336, 338,
337
309, 308
312, 311
327, 328, 335,
331, 332
314, 330, 336,
337
Oak
Panasonic
Pioneer
Scientific
Altanta
Tocom
Zenith
Symphonic
Tashiro
Tatung
Teac
209, 210, 211
Instant Replay
JC Penney
309, 308
309, 305, 304,
330, 314, 336,
337
314, 336, 337,
345, 346, 347
314, 336, 332,
337
332, 305, 330,
335, 338
308, 309, 310
314, 336, 337
332
309, 335
305, 304
216, 217
212, 213
Technics
Toshiba
Wards
JVC
Satellite Receivers
Kenwood
LXI (Sears)
Manufacturer
Code
Yamaha
Zenith
Sony
801
809
810
810
DIRECT TV
Dish Network
Echostar
General
Electric
331
Magnavox
Marantz
Marta
Memorex
Minolta
Laserdisc Players
Manufacturer
Sony
802
Code
701
Hitachi
805
Panasonic
Pioneer
704, 710
702
Hughes
Mitsubishi
Panasonic
RCA/
PROSCAN
804
809
803
802, 808
Mitsubishi/
MGA
Multitech
NEC
323, 324, 325,
326
325, 338, 321
314, 336, 337
Toshiba
806, 807
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Using your TV Remote Control with Other Equipment
Operating a VCR
Press
To
Power on the VCR (VCR/DVD green button)
Select a channel
Change channels
0
9
Play video tape
Stop
or
Search forward or backward
Pause
Record
and
Switch between VCR and TV inputs
Operating a DVD Player
Press
To
Power on the DVD (VCR/DVD green button)
Select chapters
0
9
Search chapters forward or backward
Play DVD
Stop
Pause
Display the DVD menu
Use the arrow buttons to move the cursor in the menu, and the center button to
select an option
Operating a Laser Disc Player
Press
To
Power on the laser disc (VCR/DVD green button)
Search chapters forward or backward
Play disc
Stop
Pause
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Operating a Satellite Receiver
Press
To
Power on the satellite receiver (SAT/CABLE green button)
Select a channel
Change channels
0
9
Back to previous channel
Display channel number
Display SAT GUIDE
Display SAT Menu
Use the arrow buttons to move the cursor in the menu, and the center button to
select an option
Operating a Cable Box
Press
To
Power on the cable box (SAT/CABLE green button)
Select a channel
Change channels
0
9
Change back to previous channel
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Read this section before setting up your TV for the first time. This section explains how to
make the basic connections and how to connect optional equipment.
TV Rear Panel
AUDIO OUT
1
3
6
4
1
2
3
AUDIO
AUDIO
5
Jack
Description
1 S VIDEO
This input connects to the S VIDEO OUT jack on your VCR or
other video equipment that has S VIDEO. S VIDEO provides
better picture quality than the VHF/UHF jacks or the video
input jack. S VIDEO does not provide sound, so you still must
connect the audio cables.
2 VHF/UHF
This input connects to your VHF/UHF antenna or cable.
3 AUDIO L(MONO), R/ This input connects to the AUDIO/VIDEO output jacks on your
VIDEO
VCR or other video equipment. A third video input jack
(VIDEO 2) is located on the front panel of the TV. These
AUDIO/VIDEO input jacks provide better picture quality than
the VHF/UHF jack.
4
Y, PB, PR/ L(MONO), R This input connects to the component video Y, PB, PR, and
AUDIO L(MONO), R jacks on your DVD player or digital set-
top box (480i only).
5 AUDIO OUT
(VAR/FIX)
This jack connects to the Audio input jacks on your audio
equipment. You can listen to your TV’s audio through your
stereo system.
L(MONO), R
6 Dynamic Bass
The Dynamic Bass Response System (subwoofer) accentuates
the low frequencies for better overall sound.
Response System
✍ Only the supplied Dynamic Bass Response System unit should be connected to the KV-20FA210 Sony
TV inputs (SUBWOOFER +/-).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Basic Connections
TV with Cable, Indoor, or Outdoor Antenna
Depending on the cable system available in your home, choose one of the connections below:
Use this to connect the TV to a cable system or an antenna with a 75-ohm cable
(usually built in to newer homes).
Use this to connect the TV to a dipole antenna, also known as a “rabbit ears antenna”
(usually found in older homes).
This allows you to connect your TV to both a cable system and a dipole antenna, in order to
view both cable and local channels.
✍ If you are connecting to an indoor or outdoor antenna, you may need to adjust the orientation of the
antenna for the best reception.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Dynamic Bass System Connection (Subwoofer)
•
•
Make sure to disconnect the TV before connecting the Dynamic Bass Response System.
Only the supplied Dynamic Bass Response System unit should be connected to the KV-
20FA210 Sony TV inputs (SUBWOOFER +/-).
1
Introduce the support pin of the Dynamic Bass Response System into the guide located on
top of the TV.
Dynamic Bass Response System
Pin
Guide
2
Connect the Dynamic Bass Response System cables to the indicated inputs of the TV rear
panel. Connect the gray cable to the SUBWOOFER
cable to the SUBWOOFER
(gray input). Connect the black
(black input). See illustration below.
1
3
AUDIO
AUDIO
Subwoofer + (gray)
Subwoofer - (black)
3
Once installation is complete, plug the TV's AC power cord into the wall socket.
✍ Do not plug in the AC power cord until the subwoofer is completely installed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Connecting Additional Equipment
Connecting a TV and VCR
Rear of TV
1
3
2
VCR
AUDIO
AUDIO
1
Video (yellow)
Audio L (white)
Audio R (red)
From
cable/antenna
Optional connection
1
2
Connect the coaxial cable from your TV antenna or cable service to the IN jack on your
VCR.
Connect a coaxial cable (not supplied) from the OUT jack on your VCR to the VHF/UHF
jack on the TV.
Optional connection
❏
If your VCR is equipped with video outputs, you can get better picture quality by
connecting audio/video cables (not supplied) from AUDIO/VIDEO OUT on your VCR to
AUDIO/VIDEO IN on your TV.
❏
not provide sound, so you still must connect the audio cables.
Using your TV with this connection
This connection allows you to do the following:
❏
❏
Program your Sony remote control to operate your VCR (see page 5).
To activate your remote, press
to operate your VCR. To do this, first program your
remote control, then use the Channel Fix feature to set your TV to channel 3 or 4 (see page 28).
❏
Press
repeatedly to switch between VCR input (VIDEO input) and VHF/UHF
(local channels).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
TV and Cable Box
Cable box
1
From cable/
antenna
2
Rear of TV
1
3
AUDIO
AUDIO
1
2
Connect the coaxial cable from your cable service to the IN jack on your cable box.
Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the
VHF/UHF jack on your TV.
Using your TV with this connection
This connection allows you to do the following:
❏
❏
Program your Sony remote control to operate your cable box (see page 5).
To activate your remote press to operate your cable box and then use the
0
9
buttons or CH+/- buttons to change the channels. To do this, first program your remote
control, then use the Channel Fix feature to set your TV to channel 3 or 4 (see page 28).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
TV, VCR, and Cable Box
Rear of TV
1
3
3
VCR
AUDIO
AUDIO
2
Video (yellow)
Audio L (white)
Audio R (red)
Cable Box
1
4
From
cable
1
2
Connect the coaxial cable from your cable service to the IN jack on your cable box.
Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the IN jack
on your VCR.
3
4
Connect a coaxial cable (not supplied) from the OUT jack on your VCR to the VHF/UHF
jack on the TV.
If your VCR is equipped with video outputs, you can get better picture quality by
connecting audio/video cables (not supplied) from AUDIO/VIDEO OUT on your VCR to
AUDIO/VIDEO IN on your TV.
Optional connection
❏
For better picture quality, use S VIDEO instead of the yellow video cable. S VIDEO does
Using your TV with this connection
❏
❏
Program your Sony remote control to operate your VCR or cable box (see page 5).
To activate your remote, press to operate your VCR or to operate your cable
box. To do this, first program your remote control, then use the Channel Fix feature to set
your TV to channel 3 or 4 (see page 28).
❏
Press
repeatedly to switch between VCR input (VIDEO input), VHF/UHF (local
channels or unscrambled), or cable box (cable system or scrambled channels).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a TV and Satellite Receiver
From
cable/
antenna
Rear of TV
1
3
2
Satellite receiver
1
AUDIO
AUDIO
Satellite
antenna
cable
Video (yellow)
Audio L (white)
Audio R (red)
3
1
2
Connect the cable from your satellite antenna to SATELLITE IN on your satellite receiver.
Connect the coaxial cable from your cable service or antenna to the VHF/UHF jack on
your TV.
3
Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite
receiver to AUDIO/VIDEO IN on your TV.
Using your TV with this connection
This connection allows you to do the following:
❏
❏
Program your Sony remote control to operate your satellite receiver (see page 5).
To activate your remote, press
to operate other functions.
to operate your satellite receiver. See page 7 on how
❏
Press
repeatedly to switch to satellite receiver input (VIDEO input).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Connecting a TV, VCR, and Satellite Receiver
From
Rear of TV
cable/
antenna
1
4
1
3
2
VCR
AUDIO
AUDIO
Satellite receiver
Video (yellow)
Audio L (white)
Audio R (red)
3
5
1
Connect the coaxial cable from your satellite antenna to SATELLITE IN on the satellite
receiver.
2
3
Connect the coaxial cable from your cable service or antenna to the IN jack on your VCR.
Using a coaxial cable (not supplied), connect the OUT jack on your VCR to the VHF/UHF
jack on your TV.
4
5
Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your satellite
receiver to AUDIO/VIDEO IN on your VCR.
Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your VCR to
AUDIO/VIDEO IN on your TV.
✍ To view from the satellite receiver or VCR, select the video input to which your satellite receiver or
VCR is connected by pressing
on the remote control.
Using your TV with this connection
This connection allows you to do the following:
❏
❏
❏
Program your Sony remote control to operate your VCR or satellite receiver (see page 5).
Turn on your VCR to enable your satellite receiver to work with this connection.
To activate your remote, press
receiver.
to operate your VCR or
to operate your satellite
❏
Press
repeatedly to switch between VCR input (VIDEO input), VHF/UHF
(local channels or unscrambled), or your cable box (cable system or scrambled channels).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a DVD Player
Using audio/video cables (not supplied), connect AUDIO/VIDEO OUT on your DVD player
to AUDIO/VIDEO IN on your TV.
Rear of TV
1
3
Rear of DVD Player
AUDIO
AUDIO
Video (yellow)
Audio L (white)
Audio R (red)
Optional connection
❏
For better picture quality, use S VIDEO instead of the yellow video cable. S VIDEO does
not provide sound, so you still must connect the audio cables.
If your DVD player is equipped with component video outputs (Y, PB, PR), you can
improve the picture quality by using component video cables (480i only).
❏
Rear of TV
1
3
Rear of DVD Player
AUDIO
AUDIO
PR (red)
PB (blue)
Y (green)
Audio L (white)
Audio R (red)
1
2
1
2
Using component video cables (not supplied), connect the Y, PB, PR OUT on your DVD
player to Y, PB, PR IN on your TV.
Connect AUDIO OUT on your DVD player to AUDIO IN on your TV.
✍ The Y, PB, PR outputs on your DVD player are sometimes labeled Y, CB, and CR or Y, B-Y, and R-Y. If so,
connect the cables to like colors.
Using your TV with this connection
This connection allows you to do the following:
❏
❏
❏
Program your Sony remote control to operate your DVD (see page 5).
To activate your remote, press to operate your DVD.
Press
repeatedly to switch to the DVD player's input (VIDEO input).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Connecting a Camcorder
To connect your camcorder, you can use the Audio/Video inputs on either the front or rear panel of the
TV. Using the audio/video cables (not supplied), connect the AUDIO/VIDEO OUT on your camcorder
to the AUDIO/VIDEO IN on your TV.
Front A/V Panel
Audio R (red)
Audio L (white)
Video (yellow)
A/V output
Connecting Headphones
Connect the headphones to the
jack on the front Audio/Video panel. Headphone jack is STEREO.
Front A/V Panel
Connecting an Audio System
1
Using audio/video cables (not supplied), connect AUDIO OUT on your TV to one of the unused
line inputs (e.g. TV, AUX, TAPE2) on your stereo.
2
3
Set the Speaker option to Off. For more instructions, see “Using the Audio Menu“ on page 27.
Open the Audio Out option on the Audio Menu and select Fixed to control the volume through the
connected audio system. For more instructions, see "Using the Audio Menu" on page 27.
✍ For this connection you don't need to disconnect Dynamic Bass Response System.
Rear of TV
1
3
AUDIO-L (white)
AUDIO-R (red)
AUDIO
AUDIO
Line
input
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Basic Functions
Setting Up the TV
After you have finished connecting your TV, you can use Auto Program to set up your
channels. During Auto Program, the TV will automatically search for available channels and
program receivable channels.
✍ When you start Auto Program wait until it is finished; otherwise it will skip over channels that are
available. Perform Auto Program again to program receivable channels.
1
Press
to turn on the TV. The Initial Setup screen appears.
Initial Setup
First please connect
cable / antenna
[CH+]
[CH–]
Auto Program
Exit
2
Press on the remote control or on the TV front panel to start Auto Program, or press
to exit.
✍ The Initial Setup screen appears each time you turn on the TV until you perform Auto Program.
To perform Auto Program again
1
2
3
4
Press
.
Press g to highlight Channel Setup menu.
Press f to highlight Cable. Press
to select.
Press F or f to highlight On or Off according to how you connected your TV. Press
to
select.
5
6
Press f to highlight Auto Program. Press
After Auto Program finishes, press to exit.
to search for channels.
To reset the TV to factory settings
1
2
3
Turn the TV on.
Hold down
on the remote control.
Press and release the POWER button on the TV front panel. The TV will turn itself off,
then back on.
4
Release
.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Quick Start to the Menus
The following settings are available in your on-screen menus:
Menu
Allows you to
Video : Vivid
Picture
Brightness
Color
Hue
Sharpness
Color Temp. : Cool
VM : High
Video
Mode : Vivid
Picture Controls
Move
Select
End
End
End
Return
Select
End
Adjust your picture settings.
Options
Audio
Treble
Bass
Balance
Steady Sound : Off
Effect : Off
Options
MTS : Stereo
Speaker : On
Audio Out : Fixed
Move
Select
Return
End
Select
Change your audio settings.
Channel Setup
Favorite Channels
Cable : On
Channel Fix : Off
Auto Program
Channel Skip/Add
Channel Label
Move
Select
Customize your channel settings.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Basic Functions
Menu
Allows you to
Parental Control
Password :
Set rating limits on your TV based on
program rating or content.
Move
Select
End
End
End
Timer
Timer 1 : Set
Timer 2 : Set
Current Time
Set the clock on your TV and program
scheduled viewing using Timer 1 and
Timer 2.
Move
Select
Setup
Caption Vision : Off
Video Label
Tilt Correction
Language : English
Demo
Select captioning options, label video
inputs, adjust tilt correction, select menu
language, or run a demo of the menus.
Move
Select
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
This section shows the options available for setting up and adjusting the TV.
How to Access Menus
To Access Menus
1
2
3
4
5
6
Press
to display the on-screen menu.
Use the G or g buttons to highlight the desired menu icon. Press
Use the F or f buttons to scroll up and down through the features.
Follow the instructions on the screen.
to select it.
For instructions on using a specific menu, see the page in this section that talks about that menu.
Press
to exit the menu.
✍ Press
once to display the on-screen menu, and press again to return to normal viewing. If no
buttons are pressed, the menu closes automatically after about 90 seconds.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Using the Video
Menu
To access the Video menu, use the following steps:
To Display To Select
Video
Mode : Vivid
Picture Controls
Press f to highlight an option; then press
.
Move
Select
End
Mode
Customized
picture viewing
Use the For f buttons to highlight one of the following options, then
press
to select it.
Vivid:
Select for enhanced picture contrast and sharpness.
Standard: Select for a standard picture.
Movie:
Sports:
Select for a finely detailed picture.
Select for a bright picture.
✍
Press
on the remote control for direct access to the picture modes (Vivid, Standard, Movie, Sports).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Picture Controls Menu (Video menu)
To access the Picture Controls menu, first open the Video menu by referring to
the following steps:
Video : Vivid
Picture
To Display
To Select
Brightness
Color
Hue
Sharpness
Color Temp. : Cool
VM : High
Return
Select
End
Press
f
to highlight Picture Controls, then press
.
Picture:
Brightness:
Color:
Press G to decrease the contrast. Press g to increase contrast.
Press G to darken the picture. Press g to brighten the picture.
Press G to decrease color saturation. Press g to increase color saturation.
Press G to increase the red tones. Press g to increase the green tones.
Press G to soften the picture. Press g to sharpen the picture.
Hue:
Sharpness:
Color Temp.
White color tint
adjustment
Use the F or f buttons to highlight one of the following options, then
press
to select it.
Cool:
Gives the white colors a blue tint.
Gives the white colors a neutral tint.
Gives the white colors a red tint.
Neutral:
Warm:
VM
Sharpens picture definition to give objects a crisp, clean edge. Use the
Velocity
Modulation
F or f buttons to highlight one of the following options: High, Low, Off,
then press
to select it.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Using the Audio
Menu
To access the Audio menu, use the following steps:
To Display To Highlight To Select
Audio
Treble
Bass
Balance
Steady Sound : Off
Effect : Off
Options
Press f to highlight an option; then press
.
Move
Select
End
Treble
Bass
Press G to decrease the higher pitched sounds. Press g to increase the
higher pitched sounds.
Press G to decrease the lower pitched sounds. Press g to increase the
lower pitched sounds.
Balance
Press G to emphasize the left speaker. Press g to emphasize the right
speaker.
Steady
Sound
Stabilizes
volume
Press F or f to select one of the following options, then press
to
select it.
On:
Select to stabilize the volume when changing channels.
Select to turn Steady Sound off.
Off:
Effect
Use the F or f buttons to highlight one of the following options, then
press to select it.
Simulated: Simulates stereo quality sound for mono programs.
WOW:
Provides a dramatic presence with a full, deep bass sound.
When WOW is enabled, BBE is directly activated to further
enhance the audio program.
SRS:
Off:
Produces a dynamic three dimensional sound for stereo
audio signals.
Normal stereo or mono reception.
✍ Press
to directly select Effect settings (Simulated, WOW, SRS, Off).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Options (Audio Menu)
To access the Options menu, first open the Audio menu by referring to the
following steps:
Options
To Display
To Select
To Highlight
MTS : Stereo
Speaker : On
Audio Out : Fixed
Return
End
Select
Press f to highlight Options, then press
.
MTS
Multi-Channel
TV Sound
Use the F or f buttons to highlight one of the following options, then
press
to select it.
Stereo:
Select when viewing a broadcast in stereo.
Auto SAP: Select to have the TV automatically to a Second Audio
Program (SAP) when a signal is received.
Select to reduce noise in areas of poor reception.
Mono:
✍ Press
for direct MTS settings (Stereo, Auto SAP, Mono).
✍ If your TV is set to Auto SAP, some programs may be muted or distorted. If your TV does not output
sound, change your Audio setting to Stereo or Mono.
Speaker
Custom
selection of
audio output
source
Use the F or f buttons to highlight one of the following options, then
press
to select it.
On:
Select to listen to the sound from the TV speakers with or
without a separate stereo system.
Off:
Select to turn off the TV speakers and listen to the TV’s
sound only through external audio system speakers.
Audio Out
Use the F or f buttons to highlight one of the following options, then
press to select it.
Variable: Adjust the volume through your TV.
Fixed: Adjust the TV volume through a connected stereo.
Use to control
the TV’s volume
through a stereo
✍ Audio Out settings can only be set when Speaker is set to Off.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Using the Channel Setup
Menu
To access the Channel Setup menu, use the following steps:
To Display To Highlight To Select
Channel Setup
Favorite Channels
Cable : On
Channel Fix : Off
Auto Program
Channel Skip/Add
Channel Label
Press f to highlight an option; then press
.
Move
Select
End
Favorite
1
2
3
Use the F or f buttons to highlight the position (1-8) where you want
to set a favorite channel, then press
.
Channels
Quick access
to favorite
channels
Use the F or f buttons to find the channel you want to add to your
favorite channels.
Press
to select the channel. The TV will automatically change to
the selected channel.
4
Press G to return to the Channel Setup menu or press
to exit.
✍ To use Favorite Channels, exit all menus and press
desired channel number and press
. Press F or f to move the cursor to the
.
Cable
to select it.
On:
Off:
Select if you are receiving cable channels with a CATV cable.
Select if you are using a TV antenna.
✍ After changing your cable settings, you will need to perform Auto Program. See “To perform Auto
Program again” on page 19.
Channel Fix
Use the For f buttons to highlight one of the following options, then press
to select it.
Off:
2-6:
Channel Fix is not set.
Select when you want to control all channel selection through
a cable box or VCR. Select the appropriate channel (usually 3
or 4) and use the cable box’s or VCR’s remote control for
channel selection.
Video 1:
Select from available video inputs when you have connected
video equipment (e.g., a satellite receiver) and you want your
TV fixed to it.
✍
You cannot use Favorite Channels, Cable, Channel Skip/Add, or Channel Label when Channel Fix is set.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Auto Program Perform Auto Program whenever setting up your TV.
Auto Program will search for available channels and program receivable
channels.
Channel
Skip/Add
Use this feature after you run Auto Program to skip unwanted channels or
add new ones.
1
Use the F or f buttons to highlight the position of the desired channel,
then press
Use the F or f buttons to highlight Skip or Add, then press
.
2
3
.
Press G to return to the Channel Setup menu or press to exit.
✍ Press CH + or CH - to skip over channels that have been skipped. You can still use the --9 buttons
to directly tune to skipped channels.
Channel
Label
Label up to 40
channels with
their call letters
1
Press
, then use the F or f buttons until you reach the desired
channel number.
2
3
Press
to activate the channel.
Press f to highlight Label, then press
. Use the F or f buttons to
to select.
display the first call letter or number of the label. Press
Repeat this process until you finish selecting all the call letters.
When finished, press to activate.
4
5
Press G to return to the Channel Setup menu or press
to exit.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Using the Parental Control
Menu
To access the Parental Control menu, use the following steps:
To Display To Highlight To Select
Parental Control
Password :
Use [0-9] buttons to
enter new password
Move
Select
End
The Parental Control feature helps parents monitor what their children watch on television.
To use the Parent Menu
cannot access the Parental Control menu settings without this password.
0
9
1
2
Use the
buttons to enter a 4-digit password.
Confirm your password by entering it again.
✍ Keep this manual in a safe place. You need your password for any future access to the Parental
Control menu. If you forget your password, see page 39.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Parental Control
Setting the Rating
You can change the Rating by selecting one of the Lock options.
Parental Control
Lock : Off
Change Password
Country : U.S.A.
Turn Parental Lock
Off
Move
Select
End
1
Press f to highlight Lock; then press
.
If you are not familiar with Parental Guideline rating system, use one of the following preset
categories to simplify the rating selection: Child, Youth, Young Adult.
2
Use the F or f to highlight the desired rating and press
.
Rating
Off
TV will allow a maximum rating of
No rating limit
Child
TV-Y, TV-G, G (U.S.), G, C (Canada)
TV-PG, PG (U.S.), 8 ans + (Canada)
TV-14, PG-13 (U.S.), 14+ (Canada)
Youth
Young Adult
Custom
Select to set more restrictive ratings (see next section)
Changing your Password
1
2
Follow steps 1 and 2 for “Using the Parental Control Menu” on page 30.
.
Select a Country
Select U.S.A. to use US ratings (see page 33-34) or select Canada to use Canadian ratings (see
page 35). If you select a Country (U.S.A. or Canada) that is not where you live, the rating you
select will not be activated.
1
2
Press f to highlight Country, then press
Use the F or f to highlight the desired country and press
.
.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Information for Parents
To view a program that exceeds the TV rating
0
9
❏
Press
, then use the
buttons to enter your password.
✍ Entering your password to view a blocked program will temporarily turn Lock to Off. To reactivate
selected.
Using the Custom Menu
Follow the instructions on the screen to make your custom settings. Select the country desired
for your TV’s rating limit. See page 33 for U.S. models and page 35 for Canadian models for
more information.
✍
Once you have blocked a rating or content, all higher ratings or content will be automatically blocked.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
United States: Selecting Custom Rating Options
For the United States, the Custom Rating menu includes the following options: Movie Rating,
TV Rating and Unrated. (For Canada, see page 35.)
Movie Rating
This system defines the rating levels of movies shown in theaters and on prime cable
channels.
Rating
G
Defined as
Movie Rating
G :
PG :
PG-13 :
R :
NC-17 :
X :
General audience
PG
Parental guidance suggested
Parents strongly cautioned
Restricted
PG-13
R
NC-17
X
No one 17 and under admitted
Adult audience only
Press
Return
to block
Select
End
TV Rating
The TV rating is divided into two groups: age-based and content-based.
TV Rating
TV-Y:
TV-Y7:
TV-G:
FV
Age
TV-PG:
TV-14:
TV-MA:
D L
S V
D L S V
L S V
Content
Press
Return
to block
Select
End
Age
Defined as
Content
Defined as
TV-Y
All children
FV
D
L
Fantasy violence
Suggestive dialogue
Strong language
Sexual situations
Violence
TV-Y7
TV-G
TV-PG
Directed to older children
General audience
Parental guidance
suggested
S
V
TV-14
Parents strongly cautioned
Mature audience only
TV-MA
✍
The content ratings will increase depending on the level of the age-based rating. For example, a program
with a TV-PG V (Violence) rating may contain moderate violence, while a TV-14 V (Violence) rating may
contain intense violence.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Unrated
You have the option of blocking TV programs or movies that are not rated.
Allow
Block
Allows all unrated programs
Blocks all unrated programs
Custom Rating
Movie Rating
TV Rating
Unrated : Allow
Choose a category
Return
Select
End
✍ If you choose to block unrated TV programs, please be aware that the following programs may be
blocked: emergency broadcasts, political programs, pro, news, public service announcements,
religious programs, and weather.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Canada: Selecting Custom Rating Options
For Canada, the Custom Rating menu includes the following options: English Rating, French
Rating, and U.S.A. Rating.
English Rating
These ratings are for Canadian programs that are broadcast in English.
Rating
C
Defined as
English Rating
C :
C8+ :
G :
PG :
14+ :
18+ :
Children
C8+
G
Children 8 years and older
General programming
Parental guidance
Viewers 14 and older
Adult programming
PG
14+
18+
Press
Return
to block
Select
End
French Rating
These ratings are for Canadian programs that are broadcast in French.
Rating
G
Defined as
French Rating
General
G :
8 ans+
Not recommended for
younger children
8 ans+ :
13 ans+ :
16 ans+ :
18 ans+ :
13 ans+
16 ans+
18 ans+
Not recommended for
children under age 13
Press
Return
to block
Select
Not recommended for ages
under 16
End
This program is restricted to
adults
U.S.A. Rating
For programs from the United States, see “TV Rating” on page 33.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Using the Timer
Menu
To access the Timer menu, use the following steps:
To Display
To Highlight
To Select
Timer
Timer 1 : Set
Timer 2 : Set
Current Time
Move
Select
End
Current Time
Set your TV to the current day and time. Press
Time menu:
to open the Current
1
2
Use the
Press
F
or
f
buttons to enter the correct day and time, then press
.
.
to exit the menu.
✍ You must set the Current Time before you can use Timer 1 or Timer 2.
Timer 1 and
Timer 2
Scheduled
viewing
Use the timers to program your TV to turn on and off by day, time,
duration, and channel. The timer duration is a maximum of six hours.
When the channel is fixed, it is not necessary to set the channel.
1
2
Use the
Use the F or f buttons to enter the desired day, start time, duration,
and channel, then press . The timer status should be On when the
F
or
f
buttons to highlight Timer 1 or Timer 2, then press
Timer has been set, and the timer light on the front panel of the TV
should be on.
3
Press
to exit the menu.
✍ Select Off to turn off the Timer. Your previous settings will be saved.
✍ When you perform Auto Program, Timer 1 and Timer 2 settings will be cleared. Also, in the event of
any loss of power, Current Time, Timer 1, and Timer 2 settings will be cleared.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menus
Using the Setup
Menu
To access the Setup menu, use the following steps:
To Display To Highlight To Select
Setup
Caption Vision : Off
Video Label
Tilt Correction
Language : English
Demo
Move
Select
End
Press f to highlight an option; then press
.
Caption
Vision
Allows you to select from three closed caption modes for programs that are
broadcast with closed captioning.
Closed-
Captioning
Use the F or f buttons to highlight one of the following options, then press
to select it.
Off:
Caption Vision is not activated.
CC1, 2, 3, 4: Displays printed dialogue and sound effects of a program.
Text1, 2, 3, 4: Displays network/station information.
XDS:
Displays the name of the current program and its remaining
time (if available) when you change the channel or press the
DISPLAY button.
Video Label Allows you to identify the video components connected to the TV: VCR,
Label
connected
equipment
DVD, etc. When you press TV/VIDEO to switch inputs, the Video Label
appears on-screen.
1
Press the F or f buttons to highlight the input you want to label and
press
Press the F or f buttons to highlight a label and press
.
2
3
.
Press G to return to the Setup menu or press to exit.
✍ If you select Skip, your TV skips this connection when you press the TV/VIDEO button.
Tilt
Correction
Use the F or f buttons to set the tilt of the picture from –5 to +5, then press
to activate.
Language
Display all menus in the language of your choice.
Use the F or f buttons to select from one of the following options: English,
Español (Spanish) and Français (French). Then press
.
Demo
Press
to run a demonstration of the on-screen menus.
✍ You can press any button to exit Demo mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Troubleshooting
If you have a problem with your TV, try the suggestions below. If the problem persists, see
“Contacting Sony” at the end of this section.
General
Problem
Possible Remedies
I want to reset the TV
to the factory
settings
❏
Turn on the TV. While holding down the RESET button on the
remote control, press POWER button on the TV front panel.
The TV will turn itself off, then back on again. Release the
RESET button.
The TV is dirty
❏
❏
Clean the TV with a soft dry cloth. Never use strong solvents
such as thinner or benzine, which might damage the finish of
the cabinet.
I lost the parental
control password
In the password screen, enter the following master password:
4357. After using the master password, you must create a new
password. You cannot use the master to unlock currently
blocked channels.
There is a black box
on the screen
❏
❏
You have selected a text option in the Setup menu (page 37) and
no text is available. To turn off this feature, select Off in the
Caption Vision option. If you were trying to select closed
captioning, select CC1-4 instead of Text1-4.
There was a blackout
or power outage, and
now the TV won't turn
on and the timer LED
is flashing
Press the POWER button on your remote control or on the TV
front panel.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Remote Control
Problem
Possible Remedies
I cannot operate the
remote control
❏
❏
❏
❏
Press TV (FUNCTION) when operating your TV.
Check the orientation of the batteries.
Batteries could be weak. Replace them (page 2).
Move the TV three to four feet away from fluorescent lights.
I cannot change
channels with the
remote control
❏
Make sure you have not inadvertently switched your TV from
the channel 3 or 4 setting if you are using another device to
change channels.
❏
you have pressed the FUNCTION button for that device. For
example, if you are using your VCR to control channels, be sure
to press the VCR/DVD FUNCTION button (page 3).
I lost the remote
control
❏
You can use the front panel controls to access your menus,
change channels, adjust the volume, or change video inputs
(page 2). Contact your nearest Sony Dealer to order a
replacement, please call our Sony Direct Accessory and Part
Center at 1-800-488-7669 (U.S. residents only).
Programming The Remote Control
Problem
Possible Remedies
More than one code
is listed
❏
❏
❏
Try entering them one by one until you come to the correct code
for your component.
I entered the wrong
code number
If you enter a new code number, the code number you
previously entered at that setting is erased.
I cannot operate a
component with the
remote control
Use the component's own remote control.
When I changed the
batteries, the code
numbers changed
back to the factory
settings
❏
You must reprogram the remote control (page 5).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Video
Problem
Possible Remedies
No picture, no
sound
❏
❏
If a red light is flashing on the front of your TV for more than a
problem continues, call your local service center.
when watching video equipment, set it to VIDEO 1, 2, 3, 4 or 5
(page 3).
❏
❏
❏
Make sure you have inserted the batteries correctly into the
remote control (page 2).
Try another channel to rule out station trouble.
Poor or no picture,
good sound
❏
❏
❏
Adjust the Picture setting in the Video menu (page 24).
Adjust the Brightness setting in the Video menu (page 25).
Check the antenna and/or cable connections (page 10).
No color
❏
Adjust the Color setting in the Video menu (page 24).
Only snow appears
on the screen
❏
❏
❏
Check the Cable setting in the Channel Setup menu (page 28).
Check the antenna and/or cable connections (page 10).
Make sure the channel selected is currently broadcasting.
Dotted lines or
stripes
❏
❏
Adjust the antenna.
Move the TV away from other electronic equipment. Some
electronic equipment creates electrical noise, which can
interfere with TV reception.
Double images or
ghosts
❏
Check your outdoor antenna or call your cable service.
Audio
Problem
Possible Remedies
Good picture, no
sound
❏
❏
Press
so that Muting disappears from the screen (page 3).
Check your Audio settings. Your TV may be set to Auto SAP in
the MTS feature (page 27).
❏
❏
Make sure the speaker option is set to On in the Audio Menu.
Press
to adjust your TV's volume.
Dynamic Bass Response System (Subwoofer)
Problem
Possible Remedies
No sound
❏
Check the SUBWOOFER +/- inputs on the rear panel of the TV
to make sure the cables are connected correctly (see page 11).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Channels
Problem
Possible Remedies
I cannot receive
higher number
❏
Make sure Cable is set to Off in the Channel Setup menu
(page 28).
channels (UHF) when
using an antenna
❏
Perform Auto Program to add channels that are not presently in
the memory (page 19).
Cable stations don’t
seem to work
❏
❏
Make sure Cable is set to On in the Channel Setup menu
(page 28).
Perform Auto Program to add channels that are not presently in
the memory (page 19).
I cannot get anything
but TV
❏
Be sure that you did not set the video in the Setup menu
(page 37) to skip your video inputs. If a video input has been set
to Skip, it will be skipped when you press the TV/VIDEO
button.
Contacting Sony
Before calling our Customer Information Services Center, reset the TV to factory settings (see page 21). Please have
your TV serial number ready. The number is located on the rear of your TV and on the front cover of this manual.
Our Customer Information Services Center phone number is 1-800-222-SONY (7669) (US residents only) or (416) 499-
SONY (7669) (Canadian residents only).
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Specifications
Television system
Channel coverage
Antenna
American TV standard/NTSC
VHF: 2-13/UHF: 14-69/CATV: 1-125
75-ohm external antenna terminal for VHF/UHF
FD Trinitron® tube
Picture tube
Power requirements
Supplied accessories
120V, 60 Hz
Size AA (R6) batteries (2)
Remote Control RM-Y180 (1)
Inputs/outputs
Inputs
1 video, 1 audio (front)
1 video, 1 audio (rear)
1 S VIDEO
Outputs
1 AUDIO OUT
1 Dynamic Bass Response
System (Subwoofer)
1 RF
1 Y, PB, PR, 1 audio
1 headphone jack
Optional accessories
Connecting cables VMC-810S/820S, VMC-720M,
YC-YC-15V/30V, RK74A
EAC-66U/V mixer
KV-20FA210
Screen size
Visible screen size: 507 mm (20 inches) measured diagonally
Actual screen size: 533.4 mm (21 inches) measured diagonally
6 W x 2
Speaker output
Dynamic Bass Response System 14 W
Power consumption
Dimensions (W/H/D)
Mass
145 W in use 1 W in standby
609 x 488 x 503 mm (24 x 19 / x 20 inches)
29 kg (63 lbs. 9.3 oz)
1
4
Design and specifications are subject to change without notice.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
Auto Program 19, 29
B
M
Balance 26
Bass 26
Menus
Audio 26
Channel Setup 28
Parental Control 30
Picture Controls 25
Setup 37
Timer 36
Video 24
Batteries
Inserting in remote 2
Replacing 2
C
Cable 28
Cable Box
Mode
Connections 13
Movie 24
Sports 24
Standard 24
Vivid 24
Operating 8
Caption Vision 37
Channel Fix 28
Channel Label 29
Channel Skip/Add 29
CODE SET button
Definition 3
Operating 5
Connections
Ratings
English Rating 35
French Rating 35
Movie Rating 33
TV Rating 33
U.S.A. Rating 35
Unrated 34
Cable and antenna 10
Connecting a Camcorder 18
Connecting an Audio System 18
Connecting Headphone 18
TV and VCR 12
Remote Control
Description 3
Programming 5
Reset 19, 39
Current Time 36
D
E
F
S
T
Demo 37
Setting the Rating 35
SLEEP 3
DISPLAY 3
Dynamic Bass Response System
Connection 11
Definition 1
Steady Sound 26
Treble 26
Troubleshooting 39
TV Features 1
Effect
Off 26
Simulated 26
SRS 26
WOW 26
V
Video Label 37
Favorite Channels 28
Front Panel 2
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
User Guide
Sony Corporation
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|