®
SUPER
SUPERSERVER 6113L-8
SUPERSERVER 6113L-i
USER’S MANUAL
1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 6113L-8/
6113L-i. Installation and maintainance should be performed by experienced
technicians only.
The SuperServer 6113L-8/6113L-i is a high-end, dual Itanium2 processor
rackmount server based on the SC813HS-500/SC813Hi-500 1U rackmount server
chassis and the i2DML-8G2/i2DML-iG2 serverboard.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the SUPER i2DML-8G2/i2DML-
iG2 serverboard and the SC813HS-500/SC813Hi-500 chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6113L-8/
6113L-i into a rack and check out the server configuration prior to powering up
the system. If your server was ordered without processor and memory compo-
nents, this chapter will refer you to the appropriate sections of the manual for
their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6113L-8/6113L-i.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the i2DML-8G2/i2DML-iG2
serverboard, including the locations and functions of connectors, headers and
jumpers. Refer to this chapter when adding or removing processors or main
memory and when reconfiguring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the 1U SC813HS-500/SC813Hi-500
rackmount server chassis. You should follow the procedures given in this chapter
when installing, removing or reconfiguring SCSI/IDE or peripheral drives and when
replacing the system power supply unit and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed infor-
mation on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: BIOS POST Codes
Appendix C: Software Installation
Appendix D: System Specifications
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Notes
v
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Table of Contents
Preface
About This Manual ....................................................................................................... iii
Manual Organization .................................................................................................... iii
Chapter 1: Introduction
1-1 Overview ............................................................................................................ 1-1
1-2 Serverboard Features ...................................................................................... 1-2
1-3 Server Chassis Features ................................................................................ 1-5
1-4 Contacting Supermicro ................................................................................... 1-7
Chapter 2: Server Installation
2-1 Overview ............................................................................................................ 2-1
2-2 Unpacking the SuperServer 6113L-8/6113L-i ................................................ 2-1
2-3 Preparing for Setup ......................................................................................... 2-1
Choosing a Setup Location...................................................................... 2-2
Rack Precautions ...................................................................................... 2-2
Server Precautions .................................................................................... 2-2
2-4 Installing the Server into a Rack ................................................................... 2-3
Identifying the Sections of the Rack Rails ............................................ 2-3
Installing the Outer Rails ...........................................................................2-3
Installing the Server into the Rack ...........................................................2-4
Installing the Server into a Telco Rack .................................................... 2-6
2-5 Checking the Serverboard Setup ................................................................... 2-7
2-6 Checking the Drive Bay Setup ....................................................................... 2-9
Chapter 3: System Interface
3-1 Overview ............................................................................................................ 3-1
3-2 Control Panel Buttons..................................................................................... 3-1
Reset .......................................................................................................... 3-1
Power ......................................................................................................... 3-1
3-3 Control Panel LEDs ......................................................................................... 3-2
Overheat ..................................................................................................... 3-2
NIC2 ............................................................................................................ 3-2
NIC1 ............................................................................................................ 3-2
HDD ............................................................................................................ 3-2
Power ......................................................................................................... 3-3
3-4 SCSI Drive Carrier LEDs ................................................................................. 3-3
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 4: System Safety
4-1 Electrical Safety Precautions...........................................................................4-1
4-2 General Safety Precautions .............................................................................4-2
4-3 ESD Precautions ...............................................................................................4-3
4-4 Operating Precautions ......................................................................................4-4
Chapter 5: Advanced Serverboard Setup
5-1 Handling the i2DML-8G2/i2DML-iG2 Serverboard ........................................... 5-1
5-2 Itanium2 Processor and Heatsink Installation ................................................5-2
5-3 Connecting Cables ............................................................................................5-9
Connecting Data Cables ............................................................................5-9
Connecting Power Cables ..........................................................................5-9
Connecting the Control Panel ................................................................. 5-10
5-4 I/O Ports ...........................................................................................................5-11
5-5 Installing Memory ............................................................................................5-11
5-6 Adding PCI Cards ............................................................................................5-13
5-7 Serverboard Details ....................................................................................... 5-14
i2DML-8G2 Layout .................................................................................. 5-14
i2DML-8G2/i2DML-iG2 Quick Reference .............................................. 5-15
5-8 Connector Definitions .................................................................................... 5-16
EPS 12V Power Connector.................................................................... 5-16
Processor Power Connectors ................................................................ 5-16
Power Fail LED ....................................................................................... 5-16
NMI Button............................................................................................... 5-16
Power LED ............................................................................................... 5-16
HDD LED ................................................................................................. 5-17
NIC1 LED ................................................................................................. 5-17
NIC2 LED ................................................................................................. 5-17
Overheat LED .......................................................................................... 5-17
Reset Button ........................................................................................... 5-18
Power Button ........................................................................................... 5-18
Universal Serial Bus ............................................................................... 5-18
Front Panel USB Headers ..................................................................... 5-19
Serial Ports ............................................................................................. 5-19
GLAN 1/2 (Ethernet Ports) .................................................................... 5-19
Chassis Intrusion .................................................................................... 5-19
Fan Headers ............................................................................................ 5-20
Power Fault ............................................................................................. 5-20
Wake-on-Ring .......................................................................................... 5-20
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
SMB ......................................................................................................... 5-21
SMB Power Connector ........................................................................... 5-21
5-9 Jumper Settings ............................................................................................. 5-22
Explanation of Jumpers .......................................................................... 5-22
CMOS Clear ............................................................................................ 5-22
VGA Enable/Disable ............................................................................... 5-22
GLAN Enable/Disable ............................................................................. 5-23
Watch Dog Enable/Disable .................................................................... 5-23
Power Fail Alarm Enable/Disable ......................................................... 5-23
SCSI Enable/Disable .............................................................................. 5-24
5-10 Onboard Indicators ........................................................................................ 5-24
GLAN LEDs ............................................................................................. 5-24
Debug LEDs ............................................................................................ 5-24
SCSI Activity LED................................................................................... 5-25
5-11 SCSI and IDE Disk Drive Connections ....................................................... 5-25
IDE Connectors ....................................................................................... 5-25
Ultra320 SCSI Connectors ..................................................................... 5-26
Chapter 6: Advanced Chassis Setup
6-1 Static-Sensitive Devices ................................................................................. 6-1
6-2 Control Panel ................................................................................................... 6-2
6-3 System Fans.................................................................................................... 6-3
System Fan Failure .................................................................................. 6-3
Replacing System Cooling Fans ............................................................. 6-3
6-4 Drive Bay Installation/Removal ....................................................................... 6-4
Removing the Front Bezel ....................................................................... 6-4
Accessing the Drive Bays ....................................................................... 6-5
SCSI/IDE Drive Installation ...................................................................... 6-6
CD-ROM Drive Installation ....................................................................... 6-8
6-5 Power Supply ................................................................................................... 6-9
Power Supply Failure ............................................................................... 6-9
Removing/Replacing the Power Supply .................................................. 6-9
Chapter 7: BIOS
7-1 Introduction.........................................................................................................7-1
7-2 Main Setup Screen ...........................................................................................7-2
7-3 Advanced Setup Screen ...................................................................................7-3
7-4 PCI/PnP Configuration .................................................................................... 7-11
7-5 Security settings ............................................................................................. 7-12
7-6 Exit Options .....................................................................................................7-13
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Appendices:
Appendix A: BIOS Error Beep Codes ...................................................................... A-1
Appendix B: BIOS POST Codes .............................................................................. B-1
Appendix C: Software Installation ............................................................................ C-1
Appendix D: System Specifications ........................................................................ D-1
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Notes
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 1
Introduction
1-1
Overview
The Supermicro SuperServer 6113L-8/6113L-i is a high-end dual processor, 1U
rackmount server that features some of the most advanced technology currently
available. The SuperServer 6113L-8/6113L-i is comprised of two main sub-
systems: the SC813HS-500/SC813Hi-500 1U rackmount chassis and the i2DML-
8G2/i2DML-iG2 dual Itanium2 processor serverboard. Please refer to our web
site for information on operating systems that have been certified for use with the
SuperServer 6113L-8/6113L-i (www.supermicro.com).
In addition to the mainboard and chassis, various hardware components may
have been included with your SuperServer 6113L-8/6113L-i, as listed below:
!
!
!
!
!
!
!
!
Two (2) 1U Itanium2 CPU heatsinks (SNK-0046)
One (1) heatsink retention socket with hex key (SKT-0147-RM-IT2)
Two (2) power pods: Itanium2 voltage regulator modules (VRM-0008)
One (1) slim CD-ROM drive (CDM-TEAC-24(B))
One (1) riser card (CSE-RR1U-X)
Four (4) Ultra320 SCSI drive carriers (CSE-PT-39(B), 6113L-8 only)
Four (4) IDE drive carriers (CSE-PT-42(B), 6113L-i only)
One (1) front access USB and COM port tray (CSE-PT40(B))
!
Rackmount hardware (with screws):
Two (2) rack rail assemblies
Six (6) brackets for mounting the rack rails to a rack/telco rack
!
!
One (1) CD-ROM containing drivers and utilities
SuperServer 6113L-8/6113L-i User's Manual
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Note: "(B)" indicates black.
1-2 Serverboard Features
At the heart of the SuperServer 6113L-8/6113L-i lies the i2DML-8G2/i2DML-iG2,
a dual Intel Itanium2 processor serverboard designed to provide maximum perfor-
mance. Below are the main features of the i2DML-8G2/i2DML-iG2.
Chipset
The i2DML-8G2/i2DML-iG2 is based on Intel's E8870 chipset, which is a high-
performance chipset designed for high-end server platforms (see Figure 1-1).
The Intel 8870 chipset consists of the four primary components: the Scalable Node
Controller (SNC), the Server I/O Hub (SIOH), the DDR Memory Hub (DMH), and the
Scalability Port Switch (SPS). Complementary components include the I/O Hub
Controller (Intel ICH4), the Firmware Hub (FWH), and the PCI Bus Bridge (P64H2).
The SNC is the main component in the processor/memory subsystem. It con-
nects to four DDR memory hubs through four separate links to provide a peak
memory bandwidth of 6.4 GB/s. Each DDR Memory Hub connects to two branch
channels and supports up to four DDR SDRAM DIMMs per channel. The
Scalability Port (SP) provides simultaneous, bi-directional signaling with an ag-
gregate bandwidth of 6.4 GB/sec per port. Two SP ports per SNC provide a
maximum bandwidth capability of 12.8 GB/s. The SNC delivers balanced, high-
bandwidth throughput across the processors, memory and I/O.
The SIOH is the central component of the I/O subsystem and provides the
connection between four Hub Interface 2.0 ports and two Scalability Ports. The
the SIOH with four Hub Interfaces has a aggregate peak bandwidth of 4 GB/sec.
The SIOH also offers a Hub Interface 1.5 connection to legacy I/O and firmware
via the I/O Controller Hub (ICH4).
The DMH is a bridge for data transfers between the SNC and the two DDR
memory channels. Each DMH has a maximum throughput of 1.6 GB/s and sup-
ports up to eight single or double density registered DIMMs.
The SPS is not used in the i2DML-8G2/i2DML-iG2.
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Processors
The i2DML-8G2/i2DML-iG2 supports single or dual Intel Itanium2 processors of
up to 1.50 GHz with a 6 MB L3 cache at a 400 MHz FSB. Please refer to the
support section of our web site for a complete listing of supported processors
(http://www.supermicro.com/support/).
Memory
The i2DML-8G2/i2DML-iG2 has eight 184-pin, DIMM slots that can support up to
16 GB of low-profile, registered ECC DDR200 (PC1600) SDRAM (DDR266 is
supported but at 200 MHz only). Module sizes of 128 MB, 256 MB, 512 MB, 1
GB and 2 GB may be used to populate the DIMM slots. (This serverboard has
has been designed to support 2GB DIMM modules for each memory slot, but it has
only been validated with 1GB memory modules.)
PCI Expansion Slots
The i2DML-8G2/i2DML-iG2 has one 64-bit, 133/100 MHz PCI-X slot available for
use in a 1U server configuration. A riser card is included with the server. This
riser card fits into a PCI-X slot on the serverboard and was designed specially for
the SC813HS-500/SC813Hi-500 chassis to support the use of one standard (full-
length) PCI-X card.
ATI Graphics Controller
The i2DML-8G2/i2DML-iG2 features an integrated ATI video controller based on
the Rage XL graphics chip. Rage XL fully supports sideband addressing and AGP
texturing. This onboard graphics package can provide a bandwidth of up to 512
MB/sec over a 32-bit graphics memory bus.
Onboard Controllers/Ports
The i2DML-8G2 (only) includes an onboard LSI Ultra320 SCSI controller for dual-
channel operation. Backpanel I/O ports on the 6113L-8/6113L-i include two COM
ports, two USB ports and a VGA (monitor) port. An Intel 82546EB Ethernet
controller provides support for two Gb LAN ports, which are also located on the
backpanel.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Other Features
Other onboard features are included to promote system health. These include
various voltage monitors, two CPU temperature sensors, four fan speed sensors,
a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.
Figure 1-1. E8870 Chipset Block Diagram
Processor 1
Processor 2
16 GB (Max.) DDR200
LPC Bus
DIMM1
MRH_D
DIMM5
3x1MB
FWH
DIMM2
MRH_D
DIMM6
DIMM3
SNC
IDE1
IDE2
MRH_D
DIMM7
DIMM4
MRH_D
DIMM8
PCI 32
VGA
82546EB
GLAN
Cntrl
Hublink0
Hublink0
P64H2
SIOH
PCI-X 133
ICH4
USB 2.0
USB0/1/2/
3/4/5/6
PCI-X 100
LPC Bus
Riser Card
PCI Slot
LSI U320
SCSI Cntrl
LPC
Super
I/O
3x1MB
FWH
IPMI
COM1/2
Note: This is a general block diagram. Please see the previous Serverboard
Features pages for details on the features of each serverboard.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-3 Server Chassis Features
The SC813HS-500/SC813Hi-500 is one of Supermicro's third-generation 1U chas-
sis and features four SCSI/IDE hard drive bays, a slim CD-ROM drive and a
revolutionary cooling design that can keep today's most powerful processors
running well below their temperature thresholds. The following is a general
outline of the main features of the SC813HS/SC813Hi-500 chassis.
System Power
When configured as a SuperServer 6113L-8/6113L-i, the SC813HS-500/SC813Hi-
500 chassis includes a 500W cold-swap power supply.
Control Panel
The SC813HS-500/SC813Hi-500 control panel provides important system moni-
toring and control information. LEDs indicate power on, network activity, hard
disk drive activity and system overheat conditions. Also present are a main
power button and a system reset button.
I/O Backplane
The SC813HS-500/SC813Hi-500 is a 1U rackmount chassis. Its I/O backplane
provides one full-length PCI-X slot, a COM port (another COM port is an onboard
header located near the USB2/3 ports), one VGA port, two USB ports and two
Ethernet (LAN) ports. (See Figure 1-2.)
Figure 1-2. I/O Backplane
VGA Port
PCI-X Slot
COM1 Port
USB Ports Ethernet Ports
External SCSI Port
(6113L-8 only)
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Cooling System
The SC813HS-500/SC813Hi-500 chassis' revolutionary cooling design has been
optimized to provide sufficient cooling for dual Itanium2 configurations. The
SC813HS-500/SC813Hi-500 includes two heavy duty 10-cm blower fans located
in the middle of the chassis. These fans operate continuously at full rpm. If they
break down, the ambient air temperature inside the chassis will rise and activate
an overheat LED. In addition, a high-speed 4-cm fan is also included to increase
the flow of cooling air through the system.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address:
SuperMicro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
+1 (408) 503-8008
Tel:
Fax:
Email:
marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
www.supermicro.com
Web Site:
Europe
Address:
SuperMicro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Asia-Pacific
Address:
SuperMicro, Taiwan
D5, 4F, No. 16 Chien-Ba Road
Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
+886-(2) 8226-3990
Tel:
Fax:
+886-(2) 8226-3991
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
Tel:
support@supermicro.com.tw
886-2-8228-1366, ext.132 or 139
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Notes
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6113L-8/
6113L-i up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your SuperServer 6113L-8/6113L-i system has come to you
with the processors and memory preinstalled. If your system is not already fully
integrated with a serverboard, processors, system memory etc., please turn to
the chapter or section noted in each step for details on installing specific com-
ponents.
2-2 Unpacking the SuperServer 6113L-8/6113L-i
You should inspect the box the SuperServer 6113L-8/6113L-i was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
file a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer
6113L-8/6113L-i. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fields
are generated. You will also need it placed near a grounded power outlet. Be
sure to read the Rack and Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6113L-8/6113L-i was shipped in should include two sets
of rail assemblies, six (four front and two rear) rail mounting brackets and screws
you will need to install the system into the rack. Follow the steps in the order
given to complete the installation process in a minimum amount of time. Please
read this section in its entirety before you begin the installation procedure out-
lined in the sections that follow.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Choosing a Setup Location
- Leave enough clearance in front of the rack to enable you to open
the front door completely (~25 inches).
- Leave approximately 30 inches of clearance in the back of the rack
to allow for sufficient airflow and ease in servicing.
Warnings and Precautions!
!
!
Rack Precautions
- Ensure that the leveling jacks on the bottom of the rack are fully
extended to the floor with the full weight of the rack resting on them.
- In single rack installation, stabilizers should be attached to the rack.
- In multiple rack installations, the racks should be coupled together.
- Always make sure the rack is stable before extending a component
from the rack.
- You should extend only one component at a time - extending two or
more simultaneously may cause the rack to become unstable.
Server Precautions
- Review the electrical and general safety precautions in Chapter 4.
- Determine the placement of each component in the rack before you
install the rails.
- Install the heaviest server components on the bottom of the rack
first, and then work up.
- Use a regulating uninterruptible power supply (UPS) to protect the
server from power surges, voltage spikes and to keep your
system operating in case of a power failure.
- Allow the power supply units to cool before touching them.
- Always keep the rack's front door and all panels and components on
the servers closed when not servicing to maintain proper cooling.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Server Installation
2-4 Installing the Server into a Rack
This section provides information on installing the SuperServer 6113L-8/6113L-i
into a rack unit with the rack rails provided. If the 6113L-8/6113L-i has already
been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There
are a variety of rack units on the market, which may mean the assembly proce-
dure will differ slightly. You should also refer to the installation instructions that
came with the rack unit you are using.
Identifying the Sections of the Rack Rails
You should have received two rack rail assemblies with the SuperServer 6113L-
8/6113L-i. Each of these assemblies consists of two sections: an inner fixed
chassis rail that secures to the 6113L-8/6113L-i and an outer fixed rack rail
that secures directly to the rack itself. A pair of short brackets to be used
on the front side of the outer rails are also included.
Installing the Outer Rails
Begin by measuring the distance from the front rail to the rear rail of the rack.
Attach a short bracket to the front side of the right outer rail and a long bracket
to the rear side of the right outer rail. Adjust both the short and long brackets
to the proper distance so that the rail can fit snugly into the rack. Secure the
short bracket to the front side of the outer rail with two M4 screws and the long
bracket to the rear side of the outer rail with three M4 screws. Repeat these
steps for the left outer rail.
Locking Tabs: Both chassis rails have a locking tab, which serves two functions.
The first is to lock the server into place when installed and pushed fully into the
rack, which is its normal position. Secondly, these tabs also lock the server in
place when fully extended from the rack. This prevents the server from coming
completely out of the rack when you pull it out for servicing.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Figure 2-1. Installing the Rack Rails
Installing the Server into the Rack
You should now have rails attached to both the chassis and the rack
unit. The next step is to install the server into the rack. Do this by
lining up the rear of the chassis rails with the front of the rack rails.
Slide the chassis rails into the rack rails, keeping the pressure even on
both sides (you may have to depress the locking tabs when inserting).
See Figure 2-2.
When the server has been pushed completely into the rack, you should hear the
locking tabs "click". Finish by inserting and tightening the thumbscrews that
hold the front of the server to the rack.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Server Installation
Figure 2-2. Installing the Server into a Rack
(front bezel is optional)
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Installing the Server into a Telco Rack
If you are installing the SuperServer 6113L-86113L-8/6113L-i into a Telco type
rack, follow the directions given on the previous pages for rack installation. The
only difference in the installation procedure will be the positioning of the rack
brackets to the rack. They should be spaced apart just enough to accommodate
the width of the telco rack.
Figure 2-3. Installing the Server into a Telco Rack
(front bezel is optional)
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Server Installation
2-5 Checking the Serverboard Setup
After you install the 6113L-8/6113L-i in the rack, you will need to open
the unit to make sure the serverboard is properly installed and all the connections
have been made.
1. Accessing the inside of the 6113L-8/6113L-i (see Figure 2-4):
First, release the retention screws that secure the unit to the rack. Grasp the
two handles on either side and pull the unit straight out until it locks (you will
hear a "click"). Next, depress the two buttons on the top of the chassis to
release the top cover. There is a large rectangular recess in the middle front
of the top cover to help you push the cover away from you until it stops. You
can then lift the top cover from the chassis to gain full access to the inside
of the server.
2. Check the CPUs (processors):
You may have one or two processors already installed into the serverboard.
Each processor needs its own heatsink and power pod (VRM) installed. See
Chapter 5 for instructions on processor and heatsink installation.
3. Verify the proper CPU clock ratio setting:
If the CPU speed is not automatically detected you may need to set the
correct speed with the BIOS Setup utility. See the appropriate setting in BIOS
(Chapter 7) for setting the proper CPU speed. (Most processor speeds are
automatically detected so this step should be unnecessary.)
4. Check the system memory:
Your 6113L-8/6113L-i server system may have come with system memory
already installed. Make sure all DIMMs are fully seated in their slots. For
details on adding system memory, refer to Chapter 5.
5. Installing add-on cards:
If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Figure 2-4. Accessing the Inside of the SuperServer 6113L-8/6113L-i
6. Check all cable connections and airflow:
Make sure all power and data cables are properly connected and not blocking
the chassis airflow. See Chapter 5 for details on cable connections. Also,
check the air seals for damage. The air seals are located under the blower
fan and beneath the frame cross section that separates the drive bay area from
the serverboard area of the chassis.
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Server Installation
2-6 Checking the Drive Bay Setup
Next, you should check to make sure the peripheral drives and the SCSI/IDE
drives have been properly installed and all connections have been made.
1. Accessing the drive bays:
All drives are accessable from the front of the server. For servicing the CD-
ROM and IDE drives, you will need to remove the top chassis cover (not
necessary for SCSI drives). See Chapter 6 for details.
2. CD-ROM drive:
A slim CD-ROM drive should be preinstalled in your server. Refer to Chapter
6 if you need to reinstall a CD-ROM drive to the system.
3. Check the SCSI/IDE disk drives:
Depending upon your system's configuration, your system may have one or
more SCSI (6113L-8) or IDE (6113L-i) drives already installed. If you need to
install SCSI/IDE drives, please refer to Chapter 6.
4. Check the airflow:
Airflow is provided by two heavy duty 10-cm blower fans and one high-speed
4-cm fan. The system component layout was carefully designed to direct
sufficient cooling airflow to the components that generate the most heat. Note
that all power and data cables have been routed in such a way that they do
not block the airflow generated by the fans.
5. Supplying power to the system:
The last thing you must do is to provide input power to the system. Plug the
power cord from the power supply unit into a high-quality power strip that offers
protection from electrical noise and power surges. It is recommended that you
use an uninterruptible power supply (UPS).
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Notes
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: System Interface
Chapter 3
System Interface
3-1
Overview
There are several LEDs on the chassis control panel to keep you constantly
informed of the overall status of the system as well as the activity and health of
specific components. There are also two buttons on the chassis control panel
and an on/off switch on the power supply. This chapter explains the meanings
of all LED indicators and the appropriate response you may need to take.
3-2
Control Panel Buttons
There are two push-button buttons located on the front of the chassis. These are
(in order from left to right) a reset button and a power on/off button.
RESET
!
RESET: The reset switch reboots the system.
!
POWER: This is the main power switch, which is used to apply or turn off
the main system power. Turning off system power with this button removes the
main power but keeps standby power supplied to the system.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
3-3
Control Panel LEDs
The control panel located on the front of th SC813HS-500/SC813Hi-500 chassis
has four LEDs. These LEDs provide you with critical information related to
different parts of the system. This section explains what each LED indicates
when illuminated and any corrective action you may need to take.
!
OVERHEAT: Indicates an overheat condition in the chassis. This may be
caused by cables obstructing the airflow in the system, or the ambient room
temperature being too warm. You should also check to make sure that the
chassis cover is installed and that all fans are present and operating normally.
Finally, check the air seals for damage. The air seals are located under the
blower fan and beneath the frame cross section that separates the drive bay area
from the serverboard area of the chassis.
NIC2
!
!
!
NIC2: Indicates network activity on GLAN2 when flashing .
NIC1
NIC1: Indicates network activity on GLAN1 when flashing.
HDD: Indicates SCSI/IDE channel activity. On the SuperServer 6113L-8/
6113L-i this light indicates SCSI/IDE and/or CD-ROM drive activity when flashing.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: System Interface
!
Power: Indicates power is being supplied to the system's power supply
units. This LED should normally be illuminated when the system is operating.
3-4
SCSI Drive Carrier LEDs (6113L-8 only)
Each SCSI drive carrier has two LEDs.
!
Green: When illuminated, the green LED on the front of the SCSI drive
carrier indicates drive activity. A connection to the SCSI SCA backplane enables
this LED to blink on and off when that particular drive is being accessed.
!
Red: A SAF-TE compliant backplane is needed to activate the red LED to
indicate a drive failure. If one of the SCSI drives fail, you should be notified by
your system management software. Please refer to Chapter 6 for instructions on
replacing failed SCSI drives.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Notes
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: System Safety
Chapter 4
System Safety
4-1 Electrical Safety Precautions
!
Basic electrical safety precautions should be followed to protect yourself
from harm and the SuperServer 6113L-8/6113L-ifrom damage:
! Be aware of the locations of the power on/off switch on the chassis as well as
the room's emergency power-off switch, disconnection switch or electrical
outlet. If an electrical accident occurs, you can then quickly remove power
from the system.
! Do not work alone when working with high voltage components.
! Power should always be disconnected from the system when removing or
installing main system components, such as the serverboard, memory
modules and the CD-ROM drive (not necessary for the SCSI drives). When
disconnecting power, you should first power down the system with the
operating system and then unplug the power cords of all the power supply
units in the system.
! When working around exposed electrical circuits, another person who is familiar
with the power-off controls should be nearby to switch off the power if
necessary.
! Use only one hand when working with powered-on electrical equipment. This
is to avoid making a complete circuit, which will cause electrical shock. Use
extreme caution when using metal tools, which can easily damage any
electrical components or circuit boards they come into contact with.
! Do not use mats designed to decrease electrostatic discharge as protection
from electrical shock. Instead, use rubber mats that have been specifically
designed as electrical insulators.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
! The power supply power cord must include a grounding plug and must be
plugged into grounded electrical outlets.
! Serverboard Battery: CAUTION - There is a danger of explosion if the onboard
battery is installed upside down, which will reverse its polarities. On the
i2DML-8G2/i2DML-iG2, the positive side should be facing up. This battery
must be replaced only with the same or an equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
! CD-ROMLaser:CAUTION-thisservermayhavecomeequippedwithaCD-ROM
drive. To prevent direct exposure to the laser beam and hazardous radiation
exposure, do not open the enclosure or use the unit in any unconventional
way.
4-2 General Safety Precautions
!
Follow these rules to ensure general safety:
! Keep the area around the SuperServer 6113L-8/6113L-iclean and free of clutter.
! The SuperServer 6113L-8/6113L-i weighs approximately 42 lbs (19.1 kg) when
fully loaded. When lifting the system, two people at either end should lift
slowly with their feet spread out to distribute the weight. Always keep your
back straight and lift with your legs.
!
Place the chassis top cover and any system components that have been
removed away from the system or on a table so that they won't accidentally
be stepped on.
! While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits
or be pulled into a cooling fan.
! Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into
contact with printed circuit boards or areas where power is present.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: System Safety
! After accessing the inside of the system, close the system back up and secure
it to the rack unit with the retention screws after ensuring that all connections
have been made.
4-3 ESD Precautions
!
Electrostatic discharge (ESD) is generated by two objects with different
electrical charges coming into contact with each other. An electrical discharge
is created to neutralize this difference, which can damage electronic com-
ponents and printed circuit boards. The following measures are generally
sufficient to neutralize this difference before contact is made to protect your
equipment from ESD:
! Use a grounded wrist strap designed to prevent static discharge.
! Keep all components and printed circuit boards (PCBs) in their antistatic bags
until ready for use.
! Touch a grounded metal object before removing any board from its antistatic
bag.
! Do not let components or PCBs come into contact with your clothing, which
may retain a charge even if you are wearing a wrist strap.
! Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or contacts.
! When handling chips or modules, avoid touching their pins.
! Put the serverboard and peripherals back into their antistatic bags when not
in use.
! For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
4-4 Operating Precautions
!
Care must be taken to assure that the chassis cover is in place when the 6113L-
8/6113L-i is operating to ensure proper cooling. Out of warranty damage to the
6113L-8/6113L-i system can occur if this practice is not strictly followed.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
Chapter 5
Advanced Serverboard Setup
This chapter covers the steps required to install processors and heatsinks to the
i2DML-8G2/i2DML-iG2 serverboard, connect the data and power cables and in-
stall add-on cards. All serverboard jumpers and connections are described and
a layout and quick reference chart are included in this chapter. Remember to
close the chassis completely when you have finished working on the serverboard
to protect and cool the system sufficiently.
5-1 Handling the i2DML-8G2/i2DML-iG2 Serverboard
Static electrical discharge can damage electronic components. To prevent dam-
age to printed circuit boards, it is important to handle them very carefully (see
Chapter 4). Also note that the size and weight of the serverboard can cause it
to bend if handled improperly, which may result in damage. To prevent the
serverboard from bending, keep one hand under the center of the board to support
it when handling. The following measures are generally sufficient to protect your
equipment from static discharge.
Precautions
•
•
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing any board from its antistatic
bag.
•
Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
Unpacking
The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
5-2 Itanium2 Processor and Heatsink Installation
When handling the processor package, avoid placing direct pressure
on the label area of the fan. Also, do not place the serverboard on
a conductive surface, which can damage the BIOS battery and
prevent the system from booting up.
!
IMPORTANT: Always connect the power cord last and always remove it before
adding, removing or changing any hardware components. Make sure that you
install the processor into the CPU socket before you install the CPU heatsink.
To optimize the functionality and capability of the i2DML-8G2/i2DML-iG2, we
recommend it be installed in Supermicro chassis only.
Warning: The heatsink on the MRH-D chip has been pre-installed by the
manufacturer. Please do not touch it. Turning the heatsink the wrong way will
damage it and will void the manufacturer's warranty.
Locating the Components
Locate the following components, which are included in the shipping package.
!
!
!
Two (2) power pods (VRM-0008)
Two (2) Itanium2 heatsinks (SNK-0046)
One (1) heatsink retention package, which includes:
One (1) heatsink retention mechanism (SKT-0147-RM-IT2)
Eight (8) 5-mm M3 screws
Three (3) 6-32, 4.5-mm screws
Six (6) 6-32 9-mm screws
One (1) M2.5 hex key (for CPU removal and locking)
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
Installing the Heatsink Retention Mechanism
1. Place the retention mechanism (SKT-0147-RM-IT2) on the serverboard as
shown in the picture below:
2. Secure the retention mechanism to the serverboard by screwing three 6-32,
4.5-mm screws into the mounting holes on the back of the serverboard.
Figure 5-1. Installing Heatsink Retention Mechanism
1.) Place the retention
mechanism on the
serverboard.
2.) Screw in three 6-32
4.5-mm screws from the
reverse side of the
serverboard.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Installing Itanium2 CPUs
1. Insert an Itanium2 CPU into the CPU1 socket. Make sure that CPU Pin 1 is
aligned with the cut angle of the CPU socket, as shown in the picture below.*
Itanium2 CPU
CPU1 Socket
2. Use the M2.5 hex key to secure the Itanium2 CPU as shown in the picture
below.
Securing the CPU with
an M2.5 hex key
3. Make sure that the CPU is in its properly locked position. To lock it, use the
M2.5 hex key to turn the lock in a clockwise direction. To unlock it, turn the lock
in a counter-clockwise direction.
CPU-unlocked
CPU-locked
Pointer
Pointer
4. Repeat steps 1 and 2 to install a second Itanium2 CPU as needed.*
* Please refer to the serverboard layout page in this chapter for the locations
of the CPU1 and CPU2 sockets.
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
Installing the Power Pods
The CPU power pod is a VRM mechanism specially designed for Itanium2 pro-
cessors.
1. Locate the slot on the CPU power pod and align it with the Itanium2 CPU
installed on the serverboard.
2. Carefully push the edge connector of the power pod toward the CPU until the
signal pins on both edges of the CPU are fully seated in the edge connector and
you hear a click.
!
CPU power pod
Warning: If the signal
Power pod slot
pins of the CPU are not
fully seated in the edge
connector of the power
pod, the CPU will not
function correctly!!
Edge connector
Signal pins
Itanium2 CPU
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
3. Locate four of the M3 screws in the heatsink retention package and use them
to secure the power pod onto the serverboard as shown in the picture below.
Securing the power pod with four M3 screws.
4. Repeat steps 1 and 2 to install a second power pod as needed.
Figure 5-2. Dual Itanium2 CPUs with Power Pods Installed
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
Installing Heatsinks (for CPUs without heatsinks)
Warning: Do not apply any thermal grease to the heatsink; the required amount
of thermal grease has already been applied.
To maximizing the cooling effect of the i2DML-8G2/i2DML-iG2, we strongly rec-
ommend that Supermicro's proprietary heatsinks (SNK-0046) be used with
Itanium2 CPUs.
1. Place a heatsink (SNK-0046) on top of the CPU so that the four mounting holes
are aligned with those on the retention mechanism as shown in Figure 1 below.
2. Screw in two diagonal screws (eg. the #1 and #2 screws) until just snug (do
not fully tighten), then do the same with the remaining diagonal screws as shown
in Figure 2 and Figure 3.
Figure 1
Mounting holes
Figure 2
Figure 3
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
3. Secure the heatsink onto the CPU by tightening all four screws.
4. Repeat the above steps to install a second heatsink on a second CPU if
needed.
Figure 5-3. CPUs (2) with Heatsinks Installed
Connecting AC Power
1. Connect the 24-pin power connector from the AC power supply to the
serverboard. See the serverboard layout diagram in this chapter for the locations
of the power connectors.
2. Connect the two (2) 4-pin 12V power connectors from the AC power supply
to the power pods.
3. Refer to the next section for details on all connections.
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
5-3 Connecting Cables
Now that the processors are installed, the next step is to connect the cables to
the serverboard. These include the data (ribbon) cables for the peripherals and
control panel and the power cables.
Connecting Data Cables
The ribbon cables used to transfer data from the peripheral devices have been
carefully routed in preconfigured systems to prevent them from blocking the flow
of cooling air that moves through the system from front to back. If you need to
disconnect any of these cables, you should take care to keep them routed as
they were originally after reconnecting them (make sure the red wires connect to
the pin 1 locations). If you are configuring the system, keep the airflow in mind
when routing the cables. The following data cables (with their serverboard con-
nector locations noted) should be connected. See the serverboard layout figure
in this chapter for connector locations.
! SCSI Device Cable (J3, 6113L-8 only)
! IDE Device Cable (J37, 6113L-i only)
! CD-ROM Cable (J35)
! Front Side COM Port Cable (J38)
! Front Side USB Cable (J21)
! Control Panel Cable (U66, see next page)
Connecting Power Cables
The i2DML-8G2/i2DML-iG2 has two 24-pin primary power supply connectors
designated J20 and J36 for connection to the ATX power supply. Connect the
appropriate connector from the power supply to the either of these two connec-
tors (only one connection is required) to supply power to the serverboard. See
the Connector Definitions section in this chapter for J20 and J36 pin definitions.
In addition, each processor requires a power pod. Each power pod must have
power supplied to it via one of the 4-pin header connectors included with your
power supply.
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Connecting the Control Panel
The U66 header contains pins for various buttons and indicators that are normally
located on the chassis control panel. These connectors are designed specifi-
cally for use with Supermicro server chassis. All U66 wires have been bundled
into single ribbon cable to simplify their connection. The red wire should plug into
pin 1 as marked on the serverboard. The other end connects to the Control Panel
printed circuit board, located just behind the system status LEDs in the chassis.
See the figure below for the descriptions of the various control panel buttons and
LED indicators. Refer to the Connector Definitions section in this chapter for
descriptions and pin definitions.
Figure 5-4. Front Control Panel Header Pins (U66)
20
19
Ground
X
NMI
X
Vcc
Power LED
HDD LED
Vcc
Vcc
NIC1 LED
NIC2 LED
Overheat LED
Power Fail LED
Vcc
Vcc
Vcc
Reset
Reset Button
Power Button
Ground
Ground
Pwr
2
1
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
5-4 I/O Ports
The I/O ports are color coded in conformance with the PC 99 specification. See
Figure 5-5 below for the locations of the various I/O ports.
Figure 5-5. I/O Port Locations
COM Port
USB Ports GLAN1 GLAN2
VGA Port
External SCSI
(6113L-8 only)
5-5 Installing Memory
Note: Check the Supermicro web site for recommended memory modules: http://
www.supermicro.com/support/
CAUTION
Exercise extreme care when installing or removing DIMM modules
to prevent any possible damage. Also note that the memory is
interleaved to improve performance (see step 1).
DIMM Installation (See Figure 5-6)
1. Insert four identical DIMMs (modules of the same size and type) into the
DIMM1, DIMM2, DIMM3 and DIMM4 sockets (J16, J13, J11 and J9,
repectively). (These four DIMM sockets are colored blue.) If eight DIMMs
are to be used, insert four more identical DIMMs into the DIMM5, DIMM6,
DIMM7 and DIMM8 sockets (J15, J14, J12, and J10, respectively). (These
four DIMM sockets are colored black.) The memory scheme is interleaved,
so you must install four modules at a time, beginning with the blue DIMM1,
DIMM2, DIMM3 and DIMM4 sockets.
2. Insert each DIMM module vertically into its socket. Pay attention to the notch
along the bottom of the module to prevent inserting the DIMM module incor-
rectly.
3. Gently press down on the DIMM module until it snaps into place in the socket.
Repeat for all modules (see step 1 above).
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Memory Support
The i2DML-8G2/i2DML-iG2 supports up to 16 GB of buffered, reistered ECC
DDR200 (DDR266 memory can be used but will operate at DDR200 speed). This
serverboard was designed to support 2 GB modules in each socket. You should
not mix DIMMs of different sizes and speeds.
See Figures 5-6a and 5-6b for installing and removing memory modules.
Figure 5-6a. Side View of DIMM Installation into Socket
To Install: Insert module vertically and press down until it snaps
into place. Pay attention to the bottom notch.
To Remove: Use your thumbs to gently push each release tab
outward to free the DIMM from the socket.
Figure 5-6b. Top View of DIMM Socket
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
5-6 Adding PCI Cards
1.
PCI-X slot:
The i2DML-8G2/i2DML-iG2 has one 64-bit 133 MHz PCI-X slot. The server
should have come with a riser card installed, which supports a standard sized
PCI-X card (see Figure 5-7).
2.
PCI card installation:
Before installing a PCI add-on card, see step 1, above. Begin by swinging
the release tab on the I/O backpanel shield out to the left for the PCI slot.
Insert the PCI card into the correct slot on the butterfly riser card (depending
on whether it is a standard or low-profile card), pushing down with your
thumbs evenly on both sides of the card. Finish by pushing the release tab
back to its original (locked) position. Follow this procedure when adding a
card to either slot.
Figure 5-7. Low Profile vs. Standard PCI Card Form Factor
Standard PCI
Expansion Card
Low Profile PCI
Expansion Card
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
5-7 Serverboard Details
Figure 5-8. SUPER i2DML-8G2 Layout
(not drawn to scale)
J20
J27
P W 1
CN5
U62
Fan3 Fan1
J16
J15
DIMM1
DIMM5
J13
J14
DIMM2
DIMM6
PWR Pod
(VRM)
CPU1
MRH-D
MRH-D
J30
J5
J6
DIMM3
DIMM7
J11
J12
Pwr Pod/ATI
Rage XL
CPU2
(top/bottom)
DIMM4
DIMM8
J9
J10
J29
J31
SUPER ® i2DML-8G2
J1
MRH-D
MRH-D
JV1
LAN1
LAN2
PCI-X (256 Pin)
J19
SNC
(North
Bridge)
Battery
J22
J7
P64H
J26
J2
82546
IPMI
SIOH
JA1
J18
S6
BIOS6
S4
S5
DS7
ICH4
(South
BIOS4 BIOS5
I/O
Bridge)
LSI SCSI
Controller
SPKR
S3
BIOS3 BIOS2
S2
S1
BIOS1
J25
Fan5
Fan6
JBT1
CN4
U66
J21
USB2/3
Fan8
J3
SCSI CHB
J38 COM2
Notes:
Jumpers not indicated are for test purposes only.
" indicates the location of Pin 1.
"
The i2DML-iG2 shares the same layout but does not include an onboard SCSI controller, SCSI
connectors or SCSI jumpers.
Warning:
The heatsink on the MRH-D chip has been pre-installed by the manufacturer. Please do not
touch it. Turning the heatsink the wrong way will damage it and void the manufacturer's
warranty.
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
i2DML-8G2/i2DML-iG2 Quick Reference
Jumper
Description
Default Setting
CN5
J7
J31
JBT1
JA1*
JV1
Power Fail Alarm Enable/Disable Closed (Disabled)
GLAN Enable/Disable
Watch Dog
CMOS Clear
Pins 1-2 (Enabled)
Pins 1-2 (Reset)
See Section 5-9
SCSI Enable/Disable
VGA Enable/Disable
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Connector
Description
DS3/DS4
DS7*
Fan1 - 8
J1
Debug LEDs
SCSI LEDs
Fan1 through Fan8 Headers
Backpanel USB Ports (USB0/1)
VGA Connector
J2
J3*
J5
SCSI Channel B Connector
COM1 Serial Port
J6
Wake-on-Ring Header
J9 - J16**
J18*
J19
J20
J21
J22
J25
J26
J27
DDR Memory Sockets
SCSI Channel A Connector
PCI-X Bus (256-Pin Slot)
24-pin Power1 Connector
Front Panel USB Ports (USB2/3)
System Management Bus Connector
Chassis Intrusion Header
IPMI 1.5, 2.0 Connector
System Management Bus Power Header
CPU 1/2 Sockets
J30/J29
J31
Watch Dog Reset
J36
J37/J35
J38
24-pin Power2 Connector
IDE1/2 Disk Drive Connectors
COM2 Serial Header
S1-6
U62
U66
BIOS Chips
Power Fault Connector
Front Control Panel Connector
* i2DML-8G2 only
** See Section 5-5 for details on installing memory
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
5-8 Connector Definitions
EPS 12V Power Connector
12V, 24-pin Power Supply Connector Pin
Definitions (J20, J36)
There are two 24-pin main power sup-
ply connectors on the serverboard.
These power connectors meet the
SSI EPS 12V specification. See the
table on the right for pin definitions.
(Only one of the two connections
need to be made.)
Pin Number Definition Pin Number Definition
1
2
+3.3V
+3.3V
COM
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
3
4
5
6
7
8
9
COM
PS_ON#
COM
COM
COM
Res(NC)
+5V
+5V
COM
+5V
COM
PWR_OK
5VSB
+12V
+12V
+3.3V
10
11
12
+5V
+5V
COM
Processor Power
Connectors
4-Pin, 12v Power Supply
Connectors
(to power pods)
In addition to the primary power con-
nectors, a 4-pin EPS 12V/15A power
connector (from your power supply)
must be connected to each CPU
power pod (VRM). Refer to the table
on the right for pin definitions.
Pins Definition
1 thru 2 Ground
3 thru 4
+12v
Power Fail LED
Power Fail LED Pin
Definitions
(U66)
The Power Fail LED connection is
located on pins 5 and 6 of U66. Refer
to the table on the right for pin defi-
nitions.
Pin
Number Definition
5
6
Vcc
GND
NMI Button
NMI Button Pin
Definitions (U66)
Pin
The non-maskable interrupt button
header is located on pins 19 and 20
of U66. Refer to the table on the
right for pin definitions.
Number
19
Definition
Control
20
Ground
Power LED
PWR_LED Pin Definitions
(U66)
The Power LED connection is lo-
cated on pins 15 and 16 of U66. Re-
fer to the table on the right for pin
definitions.
Pin
Number
15
Definition
Vcc
Control
16
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
HDD LED
HDD LED Pin
Definitions
(U66)
The HDD LED connection is located
on pins 13 and 14 of U66. Attach the
hard drive LED cable here to display
disk activity for any hard drives on
the system. See the table on the
right for pin definitions.
Pin
Number Definition
13
14
Vcc
HD Active
NIC1 LED
NIC LED Pin
Definitions
(U66)
The NIC (Network Interface Control-
ler) LED connection for the GLAN
port is located on pins 11 and 12 of
U66. Attach the NIC LED cable to
display network activity. Refer to the
table on the right for pin definitions.
Pin
Number Definition
11
12
Vcc
GND
NIC2 LED
NIC 2 LED Pin
Definitions
(U66)
The NIC (Network Interface Control-
ler) LED connection for the GLAN
port is located on pins 9 and 10 of
U66. Attach the NIC LED cable to
display network activity. Refer to the
table on the right for pin definitions.
Pin
Number Definition
9
10
Vcc
GND
Overheat LED (OH)
Overheat (OH) LED
Pin Definitions
(U66)
Connect an LED to the OH connec-
tion on pins 7 and 8 of U66 to provide
advanced warning of chassis over-
heating. Refer to the table on the
right for pin definitions.
Pin
Number Definition
7
8
Vcc
GND
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Reset Button
Reset Pin
Definitions
(U66)
The Reset Button connection is lo-
cated on pins 3 and 4 of U66. Attach
it the hardware reset switch on the
computer case to these pins. Refer
to the table on the right for pin defi-
nitions.
Pin
Number Definition
3
4
Reset
Ground
Power Button
Power Button
Connector
Pin Definitions
(U66)
The Power Button connection is lo-
cated on pins 1 and 2 of U66. Mo-
mentarily contacting both pins will
power on/off the system. This button
can also be configured to function as
a suspend button (see the appropri-
ate setting in BIOS). To turn off the
power when set to suspend mode,
depress the button for at least 4 sec-
onds. Refer to the table on the right
for pin definitions.
Pin
Number Definition
1
2
PW_ON
Ground
Universal Serial Bus
(USB0/1)
Universal Serial Bus Pin Definitions
USB0 USB1
Two USB 2.0 ports are located on
Pin
Number
Pin
Definition Number
Definition
+5V
P0-
P0+
Ground
Key
the backpanel. These are designated
USB0/1. USB0 is the bottom con-
nector and USB1 is the top connec-
tor of J1. See the table on the right
for pin definitions.
1
2
3
4
5
+5V
P0-
1
2
3
4
5
P0+
Ground
N/A
5-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
Front Panel Universal
Serial Bus Header
Front Panel Universal Serial Bus
Pin Definitions (J21)
Two extra USB headers (USB2/3 lo-
cated at J21) can be used to provide
front side USB access. You will
need a USB cable to use either con-
nection. Refer to the table on the
right for pin definitions.
Pin
Number
Definition
+5V
P0-
P0+
Ground
Key
1
2
3
4
5
Serial Ports
Serial Ports Pin Definitions
(J5, J38)
There are two Serial Ports on the
serverboard. The COM1 serial port
(J5) is located on the back panel and
the COM2 header (J38) is located
near the USB 2/3 connector. See
the table on the right for pin defini-
tions.
Pin Number Definition Pin Number Definition
1
2
3
4
5
DCD
6
7
8
9
DSR
RTS
CTS
RI
Serial In
Serial Out
DTR
Ground
GLAN (Ethernet) Ports
Two G-bit Ethernet ports (designated
LAN1 and LAN2) are located be-
tween USB0/1 ports and the VGA
connector. These ports accept RJ45
type cables.
Chassis Intrusion
Pin Definitions
(J25)
Chassis Intrusion
A Chassis Intrusion header (J25) is
located near JBT1 on the
serverboard. Attach the appropriate
cable to inform you of a chassis in-
trusion. See the table on the right
for pin definitions.
Pin
Number Definition
1
2
Instrusion
Ground
5-19
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Fan Headers
Fan Header Pin Definitions
(Fan1-Fan8)
The i2DML-8G2/i2DML-iG2 has eight
fan headers, designated Fan1
through Fan8. See the table on the
right for pin definitions.
Pin
Number
1
2
3
Definition
Ground (black)
+12V (red)
Tachometer
Caution: Fan headers are DC power.
Power Fault
Power Fault Pin Definitions
(U62)
Connect a cable from your power
supply to the U62 header to provide
warning of power supply failure. This
warning signal is passed through the
PWR_LED pin on U66 to indicate a
power failure on the chassis. See
the table on the right for pin defini-
tions.
Pin
Number
Definition
1
2
3
4
P/S 1 Fail Signal
P/S 2 Fail Signal
P/S 3 Fail Signal
Reset (from MB)
Note: This feature is only available when
using redundant Supermicro power sup-
plies.
Wake-On-Ring
Wake-on-Ring
Pin Definitions
(J6)
The Wake-On-Ring header is desig-
nated J6. This function allows your
computer to receive and "wake-up"
from an incoming call to the modem
when in suspend state. See the
table on the right for pin definitions.
You must have a Wake-On-Ring card
and cable to use this feature.
Pin
Number Definition
1
2
Ground
Wake-up
5-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
SMB
SMB Header Pin Definitions
(J22)
A System Management Bus header
is located at J22. Connect the ap-
propriate cable here to utilize SMB
on your system.
Pin
Number
1
2
3
4
Definition
Data
Ground
Clock
No Connection
2
SMB Power (I C)
Connector
SMB PWR Pin Definitions
(J27)
The I2C connector at J27, located be-
tween the PWR ForceOn Header and
the PWR Fault header, monitors the
status of the power supply, the fans,
and the system temperature.
Pin #
Definition
Clock
Data
N/A
1
2
3
4
5
N/A
N/A
5-21
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
5-9 Jumper Settings
Explanation of
Jumpers
Connector
Pins
3
2
1
To modify the operation of the
serverboard, jumpers can be used
to choose between optional
settings. Jumpers create shorts
between two pins to change the
function of the connector. Pin 1
is identified with a square solder
pad on the printed circuit board.
See the serverboard layout page
for jumper locations.
Jumper
Cap
3
2
1
Setting
Pin 1-2 short
Note: On two pin jumpers,
"Closed" means the jumper is on
and "Open" means the jumper is
off the pins.
CMOS Clear
JBT1 is used to clear CMOS (which will also clear any passwords). Instead of
pins, this jumper consists of contact pads to prevent accidentally clearing the
contents of CMOS.
To clear CMOS, first power down the system, then
1) Unplug the power cord(s)
2) With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver
3) Remove the screwdriver (or shorting device)
4) Reconnect the power cord(s) and power on the system.
Note: Do not use the PW_ON connector to clear CMOS.
VGA Enable/Disable
VGA Enable/Disable
Jumper Settings
(JV1)
JV1 allows you to enable or disable
Jumper
Position
1-2
2-3
Definition
Enabled
Disabled
the VGA port. The default position is
on pins 1 and 2 to enable VGA. See
the table on the right for jumper set-
tings.
5-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
GLAN Enable/Disable
GLAN
Enable/Disable
Jumper Settings
(J7)
Change the setting of jumper J7 to
enable or disable the onboard GLAN
ports (GLAN1 and GLAN2) on the
serverboard. See the table on the
right for jumper settings. The default
setting is enabled
Jumper
Position
Pins 1-2
Pins 2-3
Definition
Enabled
Disabled
Watch Dog Enable/Disable
Watch Dog
Jumper Settings (J31)
J31 controls Watch Dog, a system
monitor that takes action when a soft-
ware application freezes the system.
Jumping pins 1-2 will have WD reset
the system if a program freezes.
Jumping pins 2-3 will generate a non-
maskable interrupt for the program
that has frozen (requires software
implementation). Watch Dog must
also be enabled in BIOS.
Jumper
Position
Definition
Pins 1-2 WD to Reset
Pins 2-3
Open
WD to NMI
Disabled
Power Fail Alarm Enable/
Disable
Alarm Reset
Jumper Settings
(CN5)
The system will notify you in the
event of a power supply failure. This
feature assumes that redundant
Supermicro power supply units are
installed in the chassis. If you only
have a single power supply installed,
you should disable this (the default
setting) with CN5 to prevent false
alarms. See the table on the right for
jumper settings.
Jumper
Position
Open
Closed
Definition
Enabled
Disabled
5-23
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
SCSI Enable/Disable
(6113L-8 only)
SCSI Enable/Disable
Jumper Settings
(JA1)
The SCSI jumper at JA1 allows you to
enable or disable the onboard SCSI
controller. The normal (default) posi-
tion is on pins 1-2 to enable SCSI ter-
mination. See the table on the right
for jumper settings.
Jumper
Position
Pins 1-2
Pins 2-3
Definition
Enabled
Disabled
5-10 Onboard Indicators
GLAN LEDs
Gb LAN Right LED
Indicator
Each of the Gigabit Ethernet LAN
ports (located beside the COM2 port
on the back panel) has two LEDs.
The yellow LED indicates activity
while the other LED may be green,
orange or off to indicate the speed of
the connection. See the table at right
for the functions associated with the
second LED.
LED
Color
Off
Green
Orange
Definition
No Connection
100 Mb
1 Gb
Debug LEDs
There are two debug LEDs located
next to the IDE 2 Connector to indi-
cate common debug messages.
See the table below for the functions
associated with the debug LEDs.
Debug LED Indications
(DS3, DS4)
DS3 DS4 Indication
On On
Off On
On Off
Off Off
SNC found and start memory sizing
Initial system memory and SIOH
Valid memory and SIOH found
ICH4 found
5-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Advanced Serverboard Setup
SCSI Activity LED
(6113L-8 only)
The SCSI Activity LED is located
next to the LSI SCSI controller.
When the SCSI Activity LED blinks,
it indicates that one or both of the
SCSI channels are active.
5-11 SCSI and IDE Disk Drive Connections
When connecting the hard disk drive cables, please note that a red mark on a
wire typically designates the location of pin 1.
IDE Connectors
There are no jumpers to con-
figure the onboard IDE#1 and
#2 connectors. See the table
below for pin definitions.
IDE Connector Pin Definitions
(J37, J35)
Pin Number
1
3
5
7
9
Function
Reset IDE
Host Data 7
Host Data 6
Host Data 5
Host Data 4
Host Data 3
Host Data 2
Host Data 1
Host Data 0
GND
Pin Number
2
4
6
Function
GND
Host Data 8
Host Data 9
Host Data 10
Host Data 11
Host Data 12
Host Data 13
Host Data 14
Host Data 15
Key
GND
GND
GND
BALE
GND
IOCS16-
GND
Addr 2
Chip Select 1-
GND
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ3
I/O Write-
I/O Read-
IOCHRDY
DACK3-
IRQ14
Addr 1
Addr 0
Chip Select 0
Activity
5-25
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Ultra320 SCSI Connectors
(6113L-8 only)
Refer to the table below for the pin
definitions of the Ultra320 SCSI
connectors at J18 (SCSI channel A
and J3 (SCSI channel B).
68-pin Ultra 320 SCSI Connectors (J3 and J18)
Connector
Contact
Number
Connector
Contact
Number
Signal Names
Signal Names
1
2
3
4
5
6
7
8
+DB(12)
+DB(13)
+DB(14)
+DB(15)
+DB(P1)
+DB(0)
+DB(1)
+DB(2)
+DB(3)
+DB(4)
+DB(5)
+DB(6)
+DB(7)
+DB(P)
GROUND
DIFFSENS
TERMPWR
TERMPWR
RESERVED
GROUND
+ATN
GROUND
+BSY
+ACK
+RST
+MSG
+SEL
+C/D
+REQ
+I/O
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
-DB(12)
-DB(13)
-DB(14)
-DB(15)
-DB(P1)
-DB(0)
-DB(1)
-DB(2)
-DB(3)
-DB(4)
-DB(5)
-DB(6)
-DB(7)
-DB(P)
GROUND
GROUND
TERMPWR
TERMPWR
RESERVED
GROUND
-ATN
GROUND
-BSY
-ACK
-RST
-MSG
-SEL
-C/D
-REQ
-I/O
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
+DB(8)
+DB(9)
+DB(10)
+DB(11)
-DB(8)
-DB(9)
-DB(10)
-DB(11)
5-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Advanced Chassis Setup
Chapter 6
Advanced Chassis Setup
This chapter covers the steps required to install components and perform
maintenance on the SC813HS-500/SC813Hi-500 chassis. For component instal-
lation, follow the steps in the order given to eliminate the most common problems
encountered. If some steps are unnecessary, skip ahead to the next step.
Tools Required
The only tool you will need to install components and perform maintenance
is a Philips screwdriver.
6-1 Static-Sensitive Devices
Electricstatic discharge (ESD) can damage electronic components. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally sufficient to protect your equip-
ment from ESD damage.
Precautions
! Use a grounded wrist strap designed to prevent static discharge.
! Touch a grounded metal object before removing any board from its antistatic
bag.
! Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
! When handling chips or modules, avoid touching their pins.
! Put the serverboard, add-on cards and peripherals back into their antistatic
bags when not in use.
! For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
CD-ROM Drive
USB Ports
COM Port
Control Panel/System LEDs
SCSI/IDE Drives
System Reset
Main Power
VGA Port
PCI-X Slot
COM1 Port
USB Ports Ethernet Ports
External SCSI Port
(6113L-8 only)
Figure 6-1. Chassis: Front and Rear Views
6-2 Control Panel
The control panel (located on the front of the chassis) must be connected
to the JF2 connector on the serverboard to provide you with system status
indications. A ribbon cable has bundled these wires together to simplify the
connection. Connect the cable from JF2 on the serverboard to the appro-
priate header on the Control Panel PCB (printed circuit board). Make sure
the red wire plugs into pin 1 on both connectors. Pull all excess cabling out
of the airflow path.
The control panel LEDs inform you of system status. See "Chapter 3:
System Interface" for details on the LEDs and the control panel buttons.
Details on JF2 can be found in "Chapter 5: Advanced Serverboard Setup."
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Advanced Chassis Setup
6-3 System Fans
Two 10-cm blower fans and a high-speed 4-cm fan provide all the cooling needed
for the SuperServer 6113L-8/6113L-i. It is very important that the chassis top
cover is properly installed and making a good seal for the cooling air to circulate
properly through the chassis and cool the components. See Figure 6-2.
System Fan Failure
If a fan fails, the ambient air temperature in the chassis will rise and activate the
overheat LED on the control panel. Replace any failed fan immediately with the
same type and model. You must power down the system before replacing any
fan (removing the power cord is also recommended as a safety precaution).
Replacing System Fans
1.
Removing a 10-cm fan:
After turning off the power to the system, first remove the chassis cover
and unplug the fan cable from the serverboard. Unscrew the failed blower fan
from the chassis and pull it completely out of the chassis.
2.
Installing a new 10-cm fan:
Replace the failed fan with an identical 10-cm, 12 volt fan (available from
Supermicro, p/n FAN-0059). Install the new fan in its proper place in the
chassis by positioning it on the two mounting posts. Secure the fan to
the chassis with the screws you removed previously, then attach the fan
wires to the correct chassis fan header. Make sure the air seal under the fan
is properly installed and creating a good seal. Power up the system and
check that the fan is working properly and that the LED on the control panel
has turned off. Finish by replacing the chassis cover.
3.
Removing a 4-cm fan:
After turning off the power to the system, first remove the chassis cover and
unplug the fan cable from the serverboard. Unscrew the fan and then remove
it from the chassis.
4.
Installing a new 4-cm fan:
Replace the failed fan with an identical 4-cm fan (available from Supermicro,
p/n FAN-0061). Install the new fan in the same position as the failed one
you just removed and secure it with the screws you removed previously.
Attach the fan wires to the correct chassis fan header then power up the
system and check that the fan is working properly and that the LED on the
control panel has turned off. Finish by replacing the chassis cover.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
10-cm Blower Fans
4-cm Cooling Fan
Figure 6-2. System Cooling Fans
6-4 Drive Bay Installation/Removal
Removing the Front Bezel
If your system has a front bezel (optional) attached to the chassis, you
must first remove it to gain access to the drive bays. To remove the bezel,
first unlock the front of the chassis then press the release knob (see Figure
6-3). Carefully remove the bezel with both hands. A filter located within the
bezel can be removed for replacement/cleaning. It is recommended that you
keep a maintenance log of filter cleaning/replacement, since its condition
will affect the airflow throughout the whole system.
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Advanced Chassis Setup
Figure 6-3. Removing the Front Bezel
1. Unlock
2. Press release knob
3. Remove bezel assembly
Accessing the Drive Bays
SCSI/IDE Drives: Because of their hotswap capability, you do not need to access
the inside of the chassis or power down the system to install or replace SCSI
drives. Proceed to the next step for instructions. (For installing/removing IDE
drives, you do not need to access the inside of the system but you will need to
remove power from the system first.)
CD-ROM Drive: For installing/removing a CD-ROM drive, you will need to gain
access to the inside of the 6113L-8/6113L-i by removing the top cover of the
chassis. Proceed to the "CD-ROM Drive Installation" section later in this chapter
for instructions.
Note: Only a "slim" CD-ROM drive will fit into the 6113L-8/6113L-i.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
SCSI/IDE Drive Installation
1.
Mounting a SCSI/IDE drive in a drive carrier:
The SCSI/IDE drives are mounted in drive carriers to simplify their installation
and removal from the chassis. These carriers also help promote proper
airflow for the SCSI/IDE drive bays. For this reason, even empty carriers
without SCSI/IDE drives installed must remain in the chassis. To add a new
SCSI/IDE drive, install a drive into the carrier with the printed circuit board
side toward the carrier so that the mounting holes align with those in the
carrier. Secure the drive to the carrier with four screws, as shown in Figure
6-4.
Figure 6-4. Mounting a SCSI/IDE Drive in a Carrier
6113L-8 only: Use caution when working around the SCSI
backplane. Do not touch the backplane with any metal ob-
!
jects and make sure no ribbon cables touch the backplane or
obstruct the holes, which aid in proper airflow.
Important: Regardless of how many SCSI/IDE hard drives
are installed, all SCSI/IDE drive carriers must remain in the
!
drive bays for proper airflow.
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Advanced Chassis Setup
2.
Installing/removing hot-swap SCSI drives (6113L-8 only):
The SCSI drive bays are located in the front of the chassis, making them
easily accessible for installation and removal. The SCSI drives are hot-swap
units, meaning that they can be installed and removed while the system is
running. To remove a SCSI drive, first push the colored release button
located beside the drive's LEDs, then swing the handle fully out and use it to
pull the SCSI drive carrier straight out (see Figure 6-5).
Figure 6-5. Removing SCSI Drives
Important: All of the SCSI drive carriers must remain in
!
the drive bays to maintain proper cooling airflow.
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
CD-ROM Drive Installation
The top cover of the chassis must be opened to gain full access to the CD-ROM
drive bay. The 6113L-8/6113L-i accomodates only slim CD-ROM drives. Side
mounting brackets are needed to mount a slim CD-ROM drive in the 6113L-8/
6113L-i server.
You must power down the system before installing or removing a CD-ROM drive.
First, release the retention screws that secure the server unit to the rack. Grasp
the two handles on either side and pull the unit straight out until it locks (you will
hear a "click"). Next, depress the two buttons on the top of the chassis to
release the top cover and at the same time, push the cover away from you until
it stops. You can then lift the top cover from the chassis to gain full access to
the inside of the server.
With the chassis cover removed, unplug the power and data cables from the drive.
Then locate the locking tab at the rear of the drive. It will be on the left side of
the drive when viewed from the front of the chassis. Pull the tab away from the
drive and push the drive unit out the front of the chassis. Add a new drive by
following this procedure in reverse order. You may hear a faint *click* of the
locking tab when the drive is fully inserted. Remember to reconnect the data and
power cables to the drive before replacing the chassis cover and restoring power
to the system.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Advanced Chassis Setup
6-5 Power Supply
The SuperServer 6113L-8/6113L-i has a single 500 watt power supply, which is
auto-switching capable. This enables it to automatically sense and operate with
either a 100v or 240v input voltage. An amber light will be illuminated on the
power supply when the power is off. An illuminated green light indicates that the
power supply is operating.
Power Supply Failure
If the power supply unit fails, the system will shut down and you will need to
replace the unit. Replacement units can be ordered directly from Supermicro
(see contact information in the Preface). As there is only one power supply unit
in the 6113L-8/6113L-i, power must be completely removed from the server before
removing and replacing the power supply unit for whatever reason.
Removing/Replacing the Power Supply
1.
Removing the power supply:
First turn the power switch on the control panel off, then unplug the
power cord from the system. Remove the chassis cover by pressing the
two release buttons on the top of the chassis (near the front) and push
the chassis top rearward about one inch. To remove the failed power
unit, push the beige colored release tab to the right and then carefully lift
the unit up about 1/2 inch only. If you lift too high, you may damage the
power distribution board that the other end of the unit is connected to.
Then, pull the power unit straight back to unplug it from the power
distribution board. See Figure 6-6.
2.
Installing a new power supply:
Replace the failed unit with another unit of the same input voltage, output
voltage and wattage. It is highly recommended to replace it with exactly
the same model power supply (Supermicro part number: PWS-0048).
Carefully insert the new unit into position to plug it into the power distribution
board, making sure you are not holding it at too great an angle, which may
damage the power distribution board. Push it completely into the power
distribution board and seat it in the chassis. When correctly installed it
should be laying flat - make sure the end of the power supply is not sitting
on the stop in the chassis. Reconnect the power cord, replace the chassis
top cover and reposition the unit back into the rack. Finish by depressing
the power button on the chassis front control panel.
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Figure 6-6. Removing/Replacing the Power Supply
6-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
Chapter 7
BIOS
7-1 Introduction
This chapter describes the AMIBIOS settings for the i2DML-8G2/i2DML-iG2. The
AMI ROM BIOS is stored in a Flash EEPROM and can be easily upgraded using
a floppy disk-based program.
Starting BIOS Setup Utility
To enter the AMI BIOS Setup Utility screens, hit the <Delete> key while the
system is booting-up. (In most cases, the <Delete> key is used to invoke the BIOS
setup screen. There are a few cases when other keys are used, such as <F1> or
<F2>.)
Each BIOS menu option is described in this chapter. The BIOS setup menu
screen has two main frames. The left frame displays all the setting options;
“grayed-out” options cannot be configured while those in blue can be configured
by the user. The right frame displays the key legend. Above the key legend is
an area reserved for a text message to describe the highlighted setting. (AMIBIOS
has default text messages built in. Supermicro retains the option to include,
omit, or change any of these text messages.) When an option is selected in the
left frame, it is highlighted in white. Press the <Tab> key or the <Arrow> keys
to move between fields. Certain "hot keys" may also be used. Most of the BIOS
these hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and so on.
Options printed in Bold are default settings.
Normally, the only visible POST (Power On Self Test) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu
of the BIOS Setup utility. From the main menu, you can access the other setup
screens, such as the Chipset and Power menus. Section 7-3 gives detailed
descriptions of each parameter setting in the Setup utility.
An AMIBIOS identification string is displayed at the left bottom corner of the
screen, below the copyright message.
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
7-2 Main Setup Screen
When you first enter the BIOS Setup Utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on
the top of the screen. The Main BIOS Setup screen is shown below.
When you select the Main Setup, the AMI BIOS Version, BIOS Build Date,
BIOS ID and System Memory will all be displayed.
Language Menu
This option allows you to set the default Language used by the BIOS.
Select English (US) if you wants to use English as your default Language.
BSP Information
When you select this option, AMI BIOS will automatically display the status
of each of the following items: BSP Type, BSP Speed, BSP CPU1 ID, BSP
CPU2 ID, BSP L1 Cache, BSP L2 Cache and BSP L3 Cache.
System Time/System Date
Use this option to change the system time and date. Highlight System Time or
System Date using the <Arrow> keys. The date must be entered in MM/DD/
YYYY format. The time is entered in HH:MM:SS format. (The time follows the
24-hour format. For example, 5:30 A.M. appears as 05:30:00 and 5:30 P.M. as
17:30:00.)
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
7-3 Advanced Setup Screen
Selecting the Advanced tab takes you to the Advanced setup screen. The
Advanced BIOS Setup screen and sub menus are listed below:
When you first enter the Advanced Setup screen, the Setup Warning will be
displayed. Please follow the instructions and set the correct value for each
item to prevent the system from malfunctioning.
!Super IO Configuration
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Serial Port1 Address/Serial Port2 Address
This option specifies the base I/O port addresses and Interrupt Request
addresses of Serial Port 1 and Serial Port2. Select "Disabled" to prevent the
serial ports from accessing any system resources. When this option is set
to Disabled, the serial ports become physically unavailable. The options are
"Enabled" and "Disabled." The default setting for Serial Port1 is "Enabled".
When "Enabled" is selected for Serial Port1, the address for Serial Port1 will
be automatically set to 2F8/IRQ3. The default setting for Serial Port2 is
"Disabled". When "Disabled" is selected for Serial Port2, Serial Port2 will
become physically unavailable.
!IDE Configuration
The screen for the Primary IDE Master is shown below.
When you select this Sub Menu, AMI BIOS automatically displays the status
of the following items: Device, Vendor, Size, LBA Mode, PIO Node, Asynch
DMA, UltraDMA and S.M.A.R.T.
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
Primary IDE Master/Slave, Secondary IDE Master/Slave
From the Advanced Setup screen, press <Enter> on the appropriate option to
access primary and secondary IDE master and slave drives submenu. Use this
screen to select options for the Primary and Secondary IDE drives. Use the up
and down <Arrow> keys to select an item and the <Plus> and <Minus> keys to
change the value of the selected option.
Type
Select the type of device connected to the system. The options are "Not In-
stalled", "Auto", "CDROM" and "ARMD".
LBA/Large Mode
LBA (Logical Block Addressing) is a method of addressing data on a disk drive.
In LBA mode, the maximum drive capacity is 137 GB. For drive capacities over
137 GB, your system must be equipped with 48-bit LBA mode addressing. If not,
contact your manufacturer or install an ATA/133 IDE controller card that supports
48-bit LBA mode. The options are "Disabled" and "Auto".
Block (Multi-Sector Transfer)
Block mode boosts IDE drive performance by increasing the amount of data
transferred. Only 512 bytes of data can be transferred per interrupt if block mode
is not used. Block mode allows transfers of up to 64 KB per interrupt. Select
"Disabled" to allow the data to be transferred from and to the device one sector
at a time. Select "Auto" to allows the data transfer from and to the device occur
multiple sectors at a time if the device supports it. The options are "Auto" and
"Disabled".
PIO Mode
IDE PIO (Programmable I/O) mode programs timing cycles between the IDE drive
and the programmable IDE controller. As the PIO mode increases, the cycle time
decreases. The options are "Auto", "0", "1", "2", "3" and "4". Select Auto for
BIOS to auto detect the PIO mode. Use this value if the IDE disk drive support
cannot be determined. Select 0 for BIOS to use PIO mode 0, 1 for PIO mode 1,
2 for PIO mode 2, 3 for PIO mode 3 or 4 for PIO mode 4. These settings have
data transfer rates of 3.3 MBs, 5.2 MBs, 8.3 MBs, 11.1 MBs and 16.6 MBs,
respectively. This setting generally works with all hard disk drives manufactured
after 1999. For other disk drives, such as IDE CD-ROM drives, check the speci-
fications of the drive.
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
DMA Mode
Select the default setting of Auto to allow the BIOS to auto detect the DMA
mode. Use this value if the IDE disk drive support cannot be determined. Other-
wise, select from one of the following options: SWDMA0 (Single Word DMA mode
0, 2.1 MBs data transfer rate), SWDMA1 (Single Word DMA mode 1, 4.2 MBs
data transfer rate), SWDMA2 (Single Word DMA mode 2, 8.3 MBs data transfer
rate), MWDMA0 (Multi Word DMA mode 0, 4.2 MBs data transfer rate), MWDMA1
(Multi Word DMA mode 1, 13.3 MBs data transfer rate), MWDMA2 (Single Word
DMA mode 2, 16.6 MBs data transfer rate), UDMA0 (Ultra DMA mode 0, 16.6
MBs data transfer rate), UDMA0 (Ultra DMA mode 0, 16.6 MBs data transfer
rate), UDMA1 (Ultra DMA mode 1, 25 MBs data transfer rate), UDMA2 (Ultra
DMA mode 2, 33.3 MBs data transfer rate), UDMA3 (Ultra DMA mode 3, 66.6
MBs data transfer rate) or UDMA4 (Ultra DMA mode 4, 100 MBs data transfer
rate).
S.M.A.R.T. For Hard disk drives
Self-Monitoring Analysis and Reporting Technology (SMART) can help predict
impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk
drive support. Select "Disabled" to prevent the BIOS from using the S.M.A.R.T.
Select "Enabled" to allow the BIOS to use the S.M.A.R.T. to support hard drive
disk.
32-Bit Data Transfer
Select "Enabled" to activate the 32-Bit data transfer function. Select "Disabled"
to deactivate the function.
ARMD Emulation Type
This feature allows the BIOS to set the ARMD Emulation type. The options are
"Auto", "Floppy" and "Hard Disk."
ATA(PI) Detect Time Out
The feature allows BIOS to set the time out value for detecting ATA(PI) devices.
The options are "0", "5", "10", "15", "20", "25" and "30."
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
ATA(PI) 80-Pin Cable Detection
This feature allows the BIOS to auto-detect the 80-pin ATA(PI) Cable. The
options are "Host & Device", "Host" and "Device."
!BIOS Settings Configuration
This item allows the user to configure the system's boot settings.
Quiet Boot
Set this value to allow the boot up screen options to be modified between POST
messages or OEM logo. Select Disabled to allow the computer system to
display the POST messages. Select Enabled to allow the computer system to
display the OEM logo.
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
!System Health Monitor
This feature allows the BIOS to automatically display the status of the following
items: CPU Overheat Temperature, CPU1/CPU2 Temperature, various voltage
levels and fan speeds. See screen shot below.
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
!Peripheral Device Configuration
This screen allows the user to configure the Peripheral Device settings
Power Loss Control
This setting allows you to choose how the system will react when power is
returned to the system after being unexpectedly lost. Options are "Stay Off",
"Power On" and "Last State."
Watch Dog Timer
This setting is used to enable or disabled the Watch Dog Timer function. It
must be used in conjunction with the J31 jumper (see Chapter 2 for details).
Options are "Enabled" and "Disabled."
Watch Dog Timer Value
If the function of Watch Dog Timer (above) is enabled, this feature will allow
the user to value for the Watch Dog Timer. Options are "2 Min(utes)", "5 Min.",
"10 Min." and "15 Min."
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
!USB Configuration
This feature allows the user to configure the USB settings.
USB Function
Select "Enabled" to enable the USB Host Controller. The options are
"Disabled" and "Enabled."
Legacy USB Support
Select "Enabled" to enable support for USB Legacy. The options are
"Disabled" and "Enabled."
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
7-4 PCI/PnP Configuration
This feature allows the user to set the PCI/PnP configuration.
PCI Latency Timer
This option sets the latency time for all PCI devices on the PCI bus. The default
setting is "64." Select one of the following to set latency to the desired number
of PCI clock cycles: "32", "64", "96", "128", "160", "192", "224" and "248" (clock
cycles).
Allocate IRQ to PCI VGA
Set this value to allow or restrict the system from assigning an interrupt request
address to the VGA adapter card. The options are "Yes" and "No".
PCI IDE BusMaster
Set this value to allow or prevent the use of PCI IDE busmastering. "Enabled"
allows the BIOS to use PCI busmaster for reading and writing to IDE drives. The
options are "Disabled" and "Enabled".
PCI Slot1 Option ROM
Select "Enabled" to enable the PCI Slot1 Option ROM function. The options are
"Disabled" and "Enabled".
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
!Hardware Health Monitoring
H/W Health Function
Select "Enabled" to enable the Hardware Health Monitoring function. The
options are "Enabled" and "Disabled".
Overheat Temperature Trips
This feature allows the user to set the CPU temperature threshold. The
o
o
o
"
options range from "65 C" to "90 C. The default setting is 78 C".
7-5 Security Settings
BIOS provides a Supervisor and a User password. If you use both passwords,
the Supervisor password must be set first.
Change Supervisor Password
Select this option and press <Enter> to access the submenu, then type in the
password.
7-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7: BIOS
Change User Password
Select this option and press <Enter> to access the submenu, then type in the
password.
Clear User Password
Select this option and press <Enter> to access the submenu. You can use the
sub menu to clear the user password.
7-6 Exit Options
Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS
Setup screen.
Exit Saving Changes
When you have completed the system configuration changes, select this option
and press <Enter> to leave the BIOS Setup and boot the computer to allow the
new system configuration parameters to take effect.
Exit Discarding Changes
Select this option and press <Enter> to quit the BIOS Setup without making any
permanent changes to the system configuration and boot the computer.
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Load Optimal Defaults
Select Load Optimal Defaults from the Exit menu and press <Enter> then "OK"
to have BIOS automatically load all Optimal Defaults for the BIOS settings. The
optimal settings are designed for maximum system performance, but may not
work best for all computer applications.
Load Fail-Safe Defaults
To set this feature, select Load Fail-Safe Defaults from the Exit menu and press
<Enter>. The Fail-Safe settings are designed for maximum system stability, but
not maximum performance.
Discard Changes
Select this option and press <Enter> to discard any changes made and return
to the BIOS Utility Program.
7-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: BIOS Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each
time the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to
continue the boot-up process. The error messages normally appear on
the screen.
Fatal errors are those which will not allow the system to continue the
boot-up procedure. If a fatal error occurs, you should consult with your
system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible
beeps. The numbers on the fatal error list, on the following page,
correspond to the number of beeps for the corresponding error. All
errors listed, with the exception of Beep Code 8, are fatal errors.
POST codes may be read on the debug LEDs located beside the LAN port
on the serverboard backplane. See the description of the Debug LEDs (LED1
and LED2) in Section 2-6.
A-1 IA-32 Error Beep Codes
Beep Code Error Message
Description
Circuitshave
1beep
Refresh
been reset. (Ready to
powerup.)
5 short, 1 long Memory error
No memory detected in
system
8 beeps
Display memory read/write error
Video adapter missing or
with faulty memory
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
A-2 IA-64 Common Debug Codes
Common Debug Codes for IA-64 systems are listed below:
Checkpoints
CodeDescription
DS4
DS3
On:
Off:
On:
Off:
On
On
Off
Off
SNC found and start memory sizing
Initial system memory and SIOH
Valid memory and SIOH found
ICH4 found
Note: The debug code LEDs (DS3 and DS4) are located next to the IDE2 connector.
Please refer to the serverboard layout in Chapter 5 for DS3 and DS4 locations.
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Codes
Appendix B
BIOS POST Codes
When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O
port 0080h. If the computer cannot complete the boot process, diagnostic equipment
can be attached to the computer to read I/O port 0080h.
Checkpoint CodeDescription
D0h
The NMI is disabled. Power on delay is starting. Next, the initialization
code checksum will be verified.
D1h
Initializing the DMA controller, performing the keyboard controller
BAT test, starting memory refresh, and entering 4 GB flat mode next.
Starting memory sizing next.
D3h
D4h
Returning to real mode. Executing any OEM patches and setting the
Stack next.
D5h
D6h
Passing control to the uncompressed code in shadow RAM at
E000:0000h.Theinitializationcodeiscopiedtosegment0andcontrol
will be transferred to segment 0.
Controlisinsegment0. Next, checkingif<Ctrl><Home>waspressed
and verifying the system BIOS checksum. If either <Ctrl> <Home>
was pressed or the system BIOS checksum is bad, next will go to
checkpoint code E0h. Otherwise, going to checkpoint code D7h.
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Checkpoint CodeDescription
03h
The NMI is disabled. Next, checking for a soft reset or a power on
condition.
05h
06h
07h
08h
0Ah
The BIOS stack has been built. Next, disabling cache memory.
Uncompressing the POST code next.
Next, initializing the CPU and the CPU data area.
The CMOS checksum calculation is done next.
TheCMOSchecksumcalculationisdone.InitializingtheCMOSstatus
register for date and time next.
0Bh
0Ch
0Eh
TheCMOSstatusregisterisinitialized. Next, performinganyrequired
initialization before the keyboard BAT command is issued.
The keyboard controller input buffer is free. Next, issuing the BAT
command to the keyboard controller.
The keyboard controller BAT command result has been verified.
Next, performing any necessary initialization after the keyboard
controller BAT command test.
0Fh
10h
11h
The initialization after the keyboard controller BAT command test is
done. The keyboard command byte is written next.
The keyboard controller command byte is written. Next, issuing the
Pin 23 and 24 blocking and unblocking command.
Next, checking if <End or <Ins> keys were pressed during power on.
Initializing CMOS RAM if the Initialize CMOS RAM in every boot
AMIBIOS POST option was set in AMIBCP or the <End> key was
pressed.
12h
13h
Next,disablingDMAcontrollers1and2andinterruptcontrollers1and
2.
Thevideodisplayhasbeendisabled.PortBhasbeeninitialized.Next,
initializing the chipset.
14h
19h
1Ah
The 8254 timer test will begin next.
The 8254 timer test is over. Starting the memory refresh test next.
The memory refresh line is toggling. Checking the 15 second on/off
time next.
2Bh
2Ch
2Dh
23h
Passing control to the video ROM to perform any required configu-
ration before the video ROM test.
All necessary processing before passing control to the video ROM
is done. Looking for the video ROM next and passing control to it.
The video ROM has returned control to BIOS POST. Performing any
required processing after the video ROM had control.
Reading the 8042 input port and disabling the MEGAKEY Green
PC feature next. Making the BIOS code segment writable and
performing any necessary configuration before initializing the
interrupt vectors.
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Codes
Checkpoint CodeDescription
24h
The configuration required before interrupt vector initialization
has completed. Interrupt vector initialization is about to begin.
Interrupt vector initialization is done. Clearing the password if the
POST DIAG switch is on.
25h
27h
28h
Any initialization before setting video mode will be done next.
Initialization before setting the video mode is complete. Configuring
the monochrome mode and color mode settings next.
Bus initialization system, static, output devices will be done next, if
present. See the last page for additional information.
Completed post-video ROM test processing. If the EGA/VGA
controller is not found, performing the display memory read/write
test next.
2Ah
2Eh
2Fh
30h
31h
32h
The EGA/VGA controller was not found. The display memory read/
write test is about to begin.
The display memory read/write test passed. Look for retrace
checking next.
The display memory read/write test or retrace checking failed.
Performing the alternate display memory read/write test next.
The alternate display memory read/write test passed. Looking for
alternate display retrace checking next.
34h
37h
38h
Video display checking is over. Setting the display mode next.
The display mode is set. Displaying the power on message next.
Initializing the bus input, IPL, general devices next, if present. See the
last page of this chapter for additional information.
Displaying bus initialization error messages. See the last page of this
chapter for additional information.
39h
3Ah
3Bh
The new cursor position has been read and saved. Displaying the
Hit <DEL> message next.
The Hit <DEL> message is displayed. The protected mode memory
test is about to start.
40h
42h
Preparing the descriptor tables next.
The descriptor tables are prepared. Entering protected mode for the
memory test next.
43h
44h
45h
46h
Entered protected mode. Enabling interrupts for diagnostics mode
next.
Interrupts enabled if the diagnostics switch is on. Initializing data to
check memory wraparound at 0:0 next.
Data initialized. Checking for memory wraparound at 0:0 and finding
the total system memory size next.
The memory wraparound test is done. Memory size calculation has
been done. Writing patterns to test memory next.
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Checkpoint Code Description
47h
48h
49h
4Bh
The memory pattern has been written to extended memory. Writing
patterns to the base 640 KB memory next.
Patterns written in base memory. Determining the amount of memory
below 1 MB next.
The amount of memory below 1 MB has been found and verified.
Determining the amount of memory above 1 MB memory next.
The amount of memory above 1 MB has been found and verified.
Checking for a soft reset and clearing the memory below 1 MB for
the soft reset next. If this is a power on situation, going to checkpoint
4Eh next.
4Ch
4Dh
4Eh
4Fh
The memory below 1 MB has been cleared via a soft reset. Clearing
the memory above 1 MB next.
The memory above 1 MB has been cleared via a soft reset. Saving
the memory size next. Going to checkpoint 52h next.
The memory test started, but not as the result of a soft reset.
Displaying the first 64 KB memory size next.
The memory size display has started. The display is updated during
the memory test. Performing the sequential and random memory test
next.
50h
51h
The memory below 1 MB has been tested and initialized. Adjusting
the displayed memory size for relocation and shadowing next.
The memory size display was adjusted for relocation and shadow-
ing.
Testing the memory above 1 MB next.
52h
53h
54h
57h
58h
59h
The memory above 1 MB has been tested and initialized. Saving
the memory size information next.
The memory size information and the CPU registers are saved.
Entering real mode next.
Shutdown was successful. The CPU is in real mode. Disabling the
Gate A20 line, parity, and the NMI next.
The A20 address line, parity, and the NMI are disabled. Adjusting
the memory size depending on relocation and shadowing next.
The memory size was adjusted for relocation and shadowing.
Clearing the Hit <DEL> message next.
The Hit <DEL> message is cleared. The <WAIT...> message is
displayed. Starting the DMA and interrupt controller test next.
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Codes
Checkpoint CodeDescription
60h
62h
65h
66h
The DMA page register test passed. Performing the DMA Controller
1 base register test next.
The DMA controller 1 base register test passed. Performing the DMA
controller 2 base register test next.
The DMA controller 2 base register test passed. Programming DMA
controllers 1 and 2 next.
CompletedprogrammingDMAcontrollers1and2.Initializingthe8259
interrupt controller next.
67h
7Fh
80h
Completed 8259 interrupt controller initialization.
Extended NMI source enabling is in progress.
The keyboard test has started. Clearing the output buffer and
checking for stuck keys. Issuing the keyboard reset command next.
A keyboard reset error or stuck key was found. Issuing the keyboard
controller interface test command next.
81h
82h
83h
84h
85h
86h
87h
The keyboard controller interface test completed. Writing the com-
mand byte and initializing the circular buffer next.
The command byte was written and global data initialization has
completed. Checking for a locked key next.
Locked key checking is over. Checking for a memory size mismatch
with CMOS RAM data next.
The memory size check is done. Displaying a soft error and checking
for a password or bypassing WINBIOS Setup next.
The password was checked. Performing any required programming
before WINBIOS Setup next.
The programming before WINBIOS Setup has completed.
Uncompressing the WINBIOS Setup code and executing the
AMIBIOS Setup or WINBIOS Setup utility next.
88h
89h
8Bh
Returned from WINBIOS Setup and cleared the screen. Performing
any necessary programming after WINBIOS Setup next.
TheprogrammingafterWINBIOSSetuphascompleted.Displayingthe
power on screen message next.
The first screen message has been displayed. The <WAIT...>
message is displayed. Performing the PS/2 mouse check and
extended BIOS data area allocation check next.
Programming the WINBIOS Setup options next.
TheWINBIOSSetupoptionsareprogrammed.Resettingtheharddisk
controller next.
8Ch
8Dh
8Fh
91h
The hard disk controller has been reset. Configuring the floppy drive
controller next.
The floppy drive controller has been configured. Configuring the hard
disk drive controller next.
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Checkpoint CodeDescription
95h
Initializing the bus option ROMs from C800 next. See the last page of
this chapter for additional information.
96h
97h
Initializing before passing control to the adaptor ROM at C800.
Initialization before the C800 adaptor ROM gains control has com-
pleted. The adaptor ROM check is next.
98h
The adaptor ROM had control and has now returned control to BIOS
POST. Performing any required processing after the option ROM
returned control.
99h
9Ah
9Bh
9Ch
9Dh
9Eh
Any initialization required after the option ROM test has completed.
Configuring the timer data area and printer base address next.
Set the timer and printer base addresses. Setting the RS-232 base
address next.
Returned after setting the RS-232 base address. Performing any
required initialization before the Coprocessor test next.
Required initialization before the Coprocessor test is over. Initializing
the Coprocessor next.
Coprocessor initialized. Performing any required initialization after
the Coprocessor test next.
Initialization after the Coprocessor test is complete. Checking the
extended keyboard, keyboard ID, and Num Lock key next. Issuing the
keyboard ID command next.
A2h
A3h
Displaying any soft errors next.
The soft error display has completed. Setting the keyboard typematic
rate next.
A8h
A9h
Aah
Initialization before passing control to the adaptor ROM at E000h
completed. Passing control to the adaptor ROM at E000h next.
Returned from adaptor ROM at E000h control. Performing any
initialization required after the E000 option ROM had control next.
InitializationafterE000optionROMcontrolhascompleted.Displaying
the system configuration next.
B0h
B1h
00h
The system configuration is displayed.
Copying any code to specific areas.
Code copying to specific areas is done. Passing control to EFI.
B-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Software Installation
Appendix C
Software Installation
After all the hardware has been installed, you will need to install the operating
system and other software drivers. The necessary drivers are all included on the
Supermicro CDs that came packaged with your system.
C-1
Introduction to the EFI Platform
The EFI (Extensible Firmware Interface) Platform is a new firmware architecture that
provides an interface between the operating system and the computer firmware
(BIOS). It abstracts system data specified in the system BIOS and translates it into
an object-oriented language that can be easily accessed by the OS. It also provides
a rich environment for system pre-installation. EFI initializes chipset, buses and
drivers and locates OS loaders. Once the EFI Firmware boots up the system, it
hands over the system operation to the OS. When running in the background in the
OS environment, EFI continues to provide the system with simple runtime services
such as monitoring firmware settings and system reset. Due to the interoperability
between the OS and the system BIOS, EFI optimizes the performance of 64-bit
Itanium2 systems.
OS
EFI
BIOS
Hardware
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPER 6113L-8/6113L-i User's Manual
C-2
AMIBIOS Flash
1. Obtain a USB Pen or a USB storage device (a USB 2.0 device is recommended).
2. From our web site (www.supermicro.com), download the following two files into the
USB pen or device: [amiflash.efi], and [bios.rom].
3. Connect the USB device to one of the USB ports (see Chapter 5 for USB port
locations).
4. Bootup the system with the USB pen connected to a USB port. The system will
boot to the “EFI Boot Manager”. Highlight the “EFI Shell [Built-in]” field and press
<Enter> to select it.
Boot to EFI Boot Manager
5. Once "EFI shell (Built-in)" is selected, you enter the "EFI Shell". In the “EFI
Shell,” locate the USB device (for example fs0 or fs1).
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Software Installation
Locate of the USB device
(example)
Location of the USB device
(example)
6. At the shell command prompt, type: Shell> fsX: (where X is the number of the
sector in which your USB pen or device is located). This command will change the
directory from [Shell] to [fsX].
7. Now, start flashing BIOS by typing: fsX:\> amiflash bios.rom (where X is the sector
number in which your USB pen or device is located).
8. At the “Reset NVRAM to default value? (y/n),” prompt, please choose accordingly.
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPER 6113L-8/6113L-i User's Manual
9. When the fsx directory appears, type in the file name at the prompt: fsx:\ amiflash
ami64.rom (eg. in the example shown above, at the prompt type fs0:\> amiflash
ami64.rom and press <Enter> as shown below).
The system will now start loading the BIOS image file.
C-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Software Installation
After the BIOS Image file is loaded, the following screen will appear:
10. When "Reset NVRAM to default value? (y/n)" is displayed, type "y" at the prompt
if you want to reset all default values after flashing the BIOS. (Yes: this will reset
your NVRAM, which typically resets your boot options in EFI to the manufacturer
defaults. If you previously added options to boot from a CD-ROM or Windows, these
will disappear after NVRAM is reset, and in this case you will have to re-add the
options. No: this will leave NVRAM alone, thus your boot options will remain the
same as before BIOS was flashed.) Type "n" at the prompt if you want to keep the
default values after BIOS flashing as shown in the screen above.
11. When "Proceed with flash update? (y/n)" is displayed, type "y" at the prompt to
update the BIOS. Type "n" at the prompt if you do not wish to update the BIOS. If
you type "y", the system will automatically update the BIOS file.
12. After BIOS is updated, you will be prompted with "Reset CMOS to default values
(will be done during the next boot?) y/n?. Choose "y" if you want to reset BIOS to
the manufacturer’s default settings during the next boot, or "n" if you only want to
update BIOS without resetting it to the manufacturer’s default settings. Please note
that this reset will not affect EFI boot options.
13. You will then be prompted with "Reset the system? y/n?". Type "y" at the prompt
if you want to automatically reboot the system.
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPER 6113L-8/6113L-i User's Manual
C-3
Adding the CD-ROM Boot Option in EFI
1. Power on the system and enter the “EFI Boot Manager”.
2. Select “Boot Option Maintenance Menu."
3. Select “Add a Boot Option.”
4. Select “Removable Media Boot [Acpi(PNP0A03,0)/Pci(1F|1)/
ATA(Secondary,Master)]”.
(Note: if your CD-ROM drive is connected to the primary IDE connector,
you must choose it accordingly.)
5. Enter a new description, such as “CD-ROM”.
6. When prompted with “Enter Boot Option Data", type [A-Ascii U-Unicode
N-No boot Option]”. Then, press <Enter>.
7. When prompted with “Enter Boot Option Data", type [Data will be stored
as Unicode string:]” Then, press <Enter>.
8. When prompted with “Save changes to NVRAM [Y-Yes N-No]”,
press Y
9. Select the "Exit" option to exit the "Add Boot Option Menu".
10. Select the "Exit" option to exit the "Boot Maintenance Menu"
11. Once back in the EFI Boot Manager, you now can select the CD-ROM
boot option to boot from the OS installation CD.
C-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Software Installation
C-4
IA64 OS Installation
For installation on an IDE hard drive.
(Note: The Itanium2 board does not have a floppy connector, so the user
cannot install Windows driver through a floppy device. This procedure
uses ramdisk to add the boot device driver in EFI so that Windows OS will
automatically pick up driver from there.)
1. Make sure that the driver for the boot device (the SCSI or RAID controller) is
supported by Itanium2.
2. Copy the ramdisk.efi and driver files into a USB device (such as a USB
pen). (A USB 2.0 device is recommended.)
3. Connect the USB device to a USB port and power on the system (see
Chapter 5 for USB port locations).
4. Once the system enters the “EFI Boot Manager,” choose “EFI Shell
[Built-in]”
5. Under the “EFI Shell,” locate the USB device (for example:
fsx, fs0 or fs1...)
6. At the Shell command prompt, type: Shell> fsX: (where X is the
number of the file in which your USB pen or device is located). This
command will change the directory from [Shell] to [fsX].
7. At the new command prompt, type fsX:\> load ramdisk.efi.
T h i s
command will create a virtual block inside the EFI, which contains an
image of all files in your USB device including the boot device driver. This
new block will be the very last block under the EFI shell. (For example,
if you previously had a total of six blocks, the virtual block will be block
seven [blk7].)
8. Type: fsX:\> exit. This command will exit allow you to exit the fsX device
and return to the “EFI Boot Manager.”
9. Select “EFI Shell [Built-in]” again.
10: At the Shell command prompt, type "Shell> copy -r blkX: blk0:". This
command will copy the images from the virtual block (in this example blk7)
to block 0 (blk0). Now your driver is ready to be used by the Windows OS.
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPER 6113L-8/6113L-i User's Manual
11. At the Shell command prompt, type: "Shell> exit". This command will
exit the EFI Shell and return to the EFI Boot Manager.”
12. Select the “CD-ROM” boot option to boot from a Windows OS installation
CD after you have added the CD-ROM boot option in the EFI Boot Manager.
13. Follow the OS instruction to setup the OS.
C-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: System Specifications
Appendix D
System Specifications
Processors
®
®
Single or dual Intel Itanium 2 processors of up to 1.50 GHz with a 6
MB L3 cache at a front side (system) bus speed of 400 MHz
Note: Please refer to the support section of our web site for a complete listing of
supported processors. (http://www.supermicro.com/support/)
Chipset
Intel E8870 chipset
BIOS
®
6 MB AMI Flash ROM
Memory Capacity
Eight 184-pin, DDR DIMM sockets supporting up to 16 GB of low-profile,
registered ECC DDR200 (PC1600) SDRAM
Note: Interleaved memory; requires memory to be installed two at a time. Memory
speed is dependant on processor front side bus speed. See Chapter 5 for details.
Peripheral Drive Bays
One (1) slim CD-ROM drive
Four (4) 3.5 x 1" drive bays (for SCSI drives)
Expansion Slots (provided with riser card)
One (1) 64-bit 133/100 MHz standard PCI-X slot
Serverboard
Model: i2DML-8G2/i2DML-iG2 (Extended ATX form factor)
Dimensions: 12.25 x 13.05 in (311 x 331 mm)
Chassis
Model: SC813HS-500/SC813Hi-500 Form Factor: 1U rackmount
Dimensions: (WxHxD) 17.2 x 1.7 x 25.6 in. (437 x 44 x 650 mm)
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPERSERVER 6113L-8/6113L-i User's Manual
Weight
Gross Weight: 42 lbs. (19.1 kg.)
System Cooling
Two (2) 10-cm blower fans and one (1) high-speed 4-cm fan
System Input Requirements
AC Input Voltage: 100-240V AC auto-range
Rated Input Current: 10A (115V) to 5A (230V)
Rated Input Frequency: 50 to 60 Hz
Power Supply
Rated Output Power: 500W (Model# SP502-1S, Part # PWS-0048)
Power Distribution Strip: Part# CSE-PT813-PD5i2
Rated Output Voltages: +3.3V (21A), +5V (30A), +12V (39A), -12V (1A),
+5Vsb (2A)
BTU Rating
2750 BTUs/hr (for rated output power of 500W)
Operating Environment
Operating Temperature: 10º to 35º C (50º to 90º F)
Non-operating Temperature: -40º to 70º C (-40º to 158º F)
Operating Relative Humidity: 8% to 90% (non-condensing)
Non-operating Relative Humidity: 5 to 95% (non-condensing)
Regulatory Compliance
Electromagnetic Emissions:
FCC Class B, EN 55022 Class B, EN 61000-3-2 & EN 61000-3-3,
CISPR 22 Class B
Electromagnetic Immunity:
EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11)
Safety:
EN 60950/IEC 60950-Compliant, UL Listed (USA), CUL Listed (Canada),
TUV Certified (Germany), CE Marking (Europe)
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Calculator EL 735 User Manual
Sharp Computer Monitor TINSE1166MPZZ User Manual
Sony Cassette Player WM FX171 User Manual
Sony MP3 Player D E551 User Manual
Sony Projector Accessories DX100 User Manual
Standard Horizon Car Amplifier BMF1000D User Manual
Sunbeam Coffeemaker EM7000 User Manual
Sunbeam Kitchen Grill GC7800 User Manual
Suzuki Automobile 2008 Forenza User Manual
Swann Security Camera PNP 50 User Manual