Sony Projector Accessories DX100 User Manual

4-432-154-12 (1)  
Data  
Projector  
Operating Instructions  
Before operating the unit, please read this manual and supplied Quick Reference Manual  
thoroughly and retain it for future reference.  
VPL-DX140/DX120/DX100  
VPL-DW120  
Not all models are available in all countries and area. Please check  
with your local Sony Authorized Dealer.  
© 2012 Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B Overview  
Location and Function of Controls  
Main Unit  
qk  
1
qj  
2
qa  
qs  
qd  
qh  
3
4
5
0
qg  
qf  
k Connector panel (page 4)  
6
7
8
l Security bar  
Connects to a commercially available  
security chain or wire.  
m Security lock  
9
Connects to an optional security cable  
manufactured by Kensington.  
For details, visit Kensington’s web site.  
a Focus ring (page 10)  
c Lens  
n Control panel keys (page 5)  
o Ventilation holes (intake)  
p Speaker  
d Remote control detector  
e Foot adjust button (page 11)  
q LAMP/COVER indicator  
f Front foot (adjustable) (page 11)  
g Air filter cover/Ventilation holes  
r ON/STANDBY indicator  
i Rear feet (adjustable) (page 11)  
j Ventilation holes (exhaust)  
Caution  
Do not place anything near the ventilation  
holes as this may cause internal heat  
buildup. Do not place your hand near the  
ventilation holes and the circumference as  
this may cause injury.  
Location and Function of Controls  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                     
Connector Panel  
3 1 1  
2
3
4
c VIDEO  
Video: Video input connector  
Audio: Audio input connector  
a INPUT A  
Video: RGB/YPBPR input connector  
Audio: Audio input connector  
Note  
The audio inputs of INPUT A and VIDEO are  
shared.  
b INPUT B  
Video: HDMI input connector  
Audio: HDMI input connector  
Others  
d AC IN () socket  
Connects the supplied AC power cord.  
4
Location and Function of Controls  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Remote Commander and Control Panel Keys  
Remote Commander  
a Turning on the power/Going to  
standby mode  
?/1 (On/Standby) key  
7
4
2
1
6
b Selecting an input signal  
INPUT  
MENU  
APA  
ECO MODE  
RESET  
INPUT key  
3
4
c Operating a menu (page 14)  
MENU key  
ENTER  
RETURN  
RESET key  
PATTERN  
FREEZE  
ASPECT KEYSTONE  
ENTER /V/v/B/b (arrow) keys  
RETURN key  
BLANK  
5
D
ZOOM VOLUME  
MUTING  
d Adjusting the image (page 10)  
ASPECT key (page 16)  
PATTERN key (page 10)  
Control Panel Keys  
*
APA (Auto Pixel Alignment) key  
1
2
3
6
Note  
* Use this key when inputting a computer  
signal via the RGB input connector  
(INPUT A).  
e Using various functions during  
projecting  
*1  
D ZOOM (Digital Zoom) +/– key  
Enlarges the image with the center of it  
as a starting point while projecting.  
1 Press the D ZOOM + key to display  
the digital zoom icon on the projected  
image.  
2 Press the D ZOOM + key or the D  
ZOOM – key repeatedly to change the  
enlargement ratio. The image can be  
enlarged up to 4 times.  
Press the RESET key to restore the  
previous image.  
Location and Function of Controls  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
BLANK key  
2 Press the V/v key or ECO MODE key  
to select “ECO” or “User” mode.  
ECO: Sets each mode to the optimum  
energy-saving value.  
Cuts off the projected image  
temporarily. Press again to restore the  
previous image. Picture muting helps  
reduce power consumption.  
Lamp Mode: Low  
With No Input: Standby  
With Static Signal: Lamp  
Dimming  
MUTING key  
Mutes the audio output temporarily.  
Press again to restore the previous  
volume.  
User: Sets each item of the ECO  
mode menu as you desire (go to  
step 3).  
3 Select “User” then press the b key.  
The setting items appear.  
VOLUME +/– key  
Adjusts the volume output.  
*2  
FREEZE key  
Pauses a projected image. Press again to  
restore the image.  
User  
Lamp Mode  
High  
Notes  
Auto Power Saving  
*1: Use this key when inputting a  
computer signal. But it may not be  
used depending on the resolution of  
the input signal.  
With No Input  
With Static Signal Lamp Dimming  
Off  
:Sel  
RETURN :Back  
:Set  
*2: Use this key when inputting a  
computer signal.  
4 Press the V/v key to select the item  
then press the ENTER key.  
5 Press the V/v key to select the setting  
value.  
f Setting the energy–saving mode  
easily  
6 Press the ENTER key.  
The screen returns to the previous  
menu.  
For details on ECO Mode settings, see  
“Lamp Mode”, “With No Input” and  
“With Static Signal” on the Connection/  
Power menu (page 22).  
ECO MODE key  
Energy-saving mode can be set easily.  
Energy-saving mode consists of “Lamp  
Mode,” “With No Input,” and “With  
Static Signal.”  
1 Press the ECO MODE key to display  
the ECO Mode menu.  
Others  
ECO Mode Menu  
g Infrared transmitter  
ECO Mode  
ECO  
User  
About remote commander operation  
• Direct the remote commander toward the  
remote control detector.  
• The shorter the distance between the  
remote commander and the projector is,  
the wider the angle within which the  
remote commander can control the  
projector becomes.  
RETURN  
:Sel  
:Back  
• Make sure that nothing obstructs the  
infrared beam between the remote  
commander and the remote control  
detector on the projector.  
6
Location and Function of Controls  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
B Preparation  
Connecting the Projector  
Notes  
• Make sure all the equipment is powered off when connecting the projector.  
• Use the proper cables for each connection.  
• Insert the cable plugs firmly; Loose connections may reduce performance of picture signals or  
cause a malfunction. When pulling out a cable, be sure to grip it by the plug, not the cable itself.  
• For more information, refer also to the instruction manuals of the equipment you are connecting.  
• Use a no-resistance audio cable.  
Connecting a Computer  
Connection with a computer is explained for each input signal.  
INPUT A  
For connecting a computer with an RGB output connector.  
Mini D-sub 15-pin cable (supplied)  
RGB output  
connector  
Audio output  
connector  
Computer  
Audio cable (Stereo mini plug)  
(not supplied)  
INPUT B  
For connecting a computer with an HDMI output connector.  
HDMI cable  
HDMI output  
(not supplied)  
connector  
Computer  
Notes  
• Use HDMI-compatible equipment and cable(s) that have an HDMI logo on them.  
• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal  
or CEC (Consumer Electronics Control) Signal.  
• It is recommended that you set the resolution of your computer to 1024 × 768 pixels (VPL-DX140/  
DX120/DX100) or 1280 × 800 pixels (VPL-DW120) for the external monitor.  
Connecting the Projector  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Connecting a Video equipment  
Connections with a DVD player or BD player are explained for each input signal.  
VIDEO  
For connecting video equipment with a video output connector.  
Video cable (not supplied)  
Video output  
connector  
Audio output  
connector  
Video equipment  
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)  
INPUT A  
For connecting video equipment with a YPBPR output connector.  
Component – Mini D-sub 15-pin cable (not supplied)  
YPBPR output  
connector  
Audio output  
connector  
Video equipment  
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)  
INPUT B  
For connecting video equipment with an HDMI output connector.  
HDMI cable  
(not supplied)  
HDMI output  
connector  
Video equipment  
Notes  
• Use HDMI-compatible equipment and cable(s) that have an HDMI logo on them.  
• The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal  
or CEC (Consumer Electronics Control) Signal.  
8
Connecting the Projector  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
B Projecting/Adjusting an Image  
Projecting an Image  
The size of a projected image depends on the distance between the projector and screen. Install  
the projector so that the projected image fits the screen size. For details on projection distances  
and projected image sizes, see “Projection Distance” (page 37).  
Input  
Video  
Input-A  
Input-B  
Sel  
3
5
4
2
Video equipment  
Projector  
1
6
Wall outlet  
Computer  
1 Plug the AC power cord into the wall  
6 When projecting a computer image,  
switch your computer’s output to  
external display.  
outlet.  
The method to switch the output varies  
depending on the type of computer.  
2 Connect all equipment to the projector  
(Example)  
3 Press the ?/1 key to turn on the unit.  
4 Turn on the connected equipment.  
5 Select the input source.  
+
7 Adjust the focus, size and position of  
the projected image (page 10).  
Press the INPUT key on the projector to  
display the menu for switching input  
signal on the screen. Press the INPUT  
key repeatedly, or press the V/v key to  
select an image to be projected.  
Projecting an Image  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Adjusting the Projected image  
Focus  
Size (Zoom)  
Position  
Zoom ring  
Foot adjust  
button  
Front foot  
(adjustable)  
Focus ring  
Rear feet  
(adjustable)  
Displaying a pattern for adjusting an image  
You can display a pattern for adjusting the projected image with the PATTERN key on the  
remote commander. Press the PATTERN key again to restore the previous image.  
10 Projecting an Image  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Adjusting the tilt of the projector with the foot adjust button/rear feet  
(adjustable)  
By changing the tilt of the projector with the foot adjust button/rear feet (adjustable), you can  
adjust the position of the projected image.  
1
Press and hold the foot adjust button,  
then lift up the front of the projector to  
adjust the angle.  
2 When the desired angle is achieved,  
release the foot adjust button to lock the  
position.  
3 Set the angle of the projector precisely  
by turning the rear feet (adjustable).  
Notes  
• Be careful not to let the projector down on your fingers.  
• Do not push hard on the top of the projector with the front foot (adjustable) extended.  
• Do not forcedly turn the rear feet (adjustable) more than they should be adjusted. Doing so may  
break them.  
Changing the aspect ratio of the projected image  
Press the ASPECT key on the remote commander to change the aspect ratio of the projected  
image. You can also change the setting in Aspect of the Screen menu (pages 16, 18).  
Projecting an Image 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
*1  
Correcting trapezoidal distortion of the projected image (Keystone feature)  
Keystone feature may not work automatically when the screen is tilted. In this case, set  
*2  
keystone manually.  
1 Press the KEYSTONE key on the remote  
commander or select V Keystone in the  
Installation menu.  
2 Use the V/v/B/b the keys to set the value.  
The higher the value, the narrower the top  
of the projected image. The lower the  
value, the narrower the bottom.  
Increase the number  
towards plus  
Notes  
*1: Since the Keystone adjustment is an  
electronic correction, the image may be  
deteriorated.  
*2: VPL-DX140/DX120/DW120 only.  
Increase the number  
towards minus  
Automatically adjusts Phase, Pitch and Shift of projected image while a  
signal is input from a computer (APA (Auto Pixel Alignment))  
Press the APA key on the remote commander. Press again to cancel adjusting during the setting.  
You can also set APA in the Screen Menu (page 17). If Smart APA in the Function menu is set  
to “On”, executes APA automatically when a signal is input (page 20).  
12 Projecting an Image  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Turning Off the Power  
1 Press the ?/1 key on the unit or the remote commander.  
The projector starts shutdown and turns off. If you press the ?/1 key within 10 seconds of  
the message being displayed, shutdown is canceled.  
2 Unplug the AC power cord from the wall outlet.  
To turn off without displaying confirmation message  
Press and hold the ?/1 key on the unit for a few seconds (page 26).  
ECO gauge  
This gauge indicates the current effectiveness of the projector’s ECO function.  
(For details on the ECO function, see “ECO MODE key” (page 6) and “ECO” (page 22).)  
The leaf icons are displayed when the projector is shut down. The number of displayed icons  
varies according to how much energy is saved as a result of using the ECO function.  
ECO gauge  
Projecting an Image 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
B Adjustments and Settings Using a Menu  
Using a MENU  
Note  
The menu displays used for the explanation below may be different depending on the model you are  
using.  
operations in step 3 and then press the  
1 Press the MENU key to display the  
ENTER key to register the setting.  
To return to the selection screen of the  
setting items, press the B or RETURN  
key. As an aid to setting or adjusting  
items, you can press the RESET key to  
return an item to its factory setting.  
menu.  
2 Select the setting menu.  
Use the V/v key to select the setting  
menu then press the b key or ENTER  
key.  
Setting menu  
Using a pop-up menu  
Press the V/v/B/b key to select an item.  
A selected item takes effect  
immediately, except “Language”, which  
will take effect after you press the  
ENTER key.  
Picture  
Picture Mode  
Reset  
Contrast  
Brightness  
Color  
Hue  
Color Temp.  
Sharpness  
Expert Setting  
Standard  
Low  
30  
Picture Mode  
Dynamic  
Standard  
:Sel  
:Set  
:Back  
Presentation  
Blackboard  
Game  
Cinema  
3 Select the setting item.  
Use the V/v key to select the setting  
menu then press the b key or ENTER  
key.  
:Sel  
RETURN :Back  
Using the setting menu  
Press the V/v key to select the item.  
A selected item takes effect  
immediately. The previous screen is  
restored.  
Using the adjustment menu  
To increase the value, press the V/b key  
and to decrease the number, press the  
v/B key. If you press the ENTER key,  
the selected item takes effect  
immediately. The previous screen is  
restored.  
To return to the selection screen of the  
setting menu, press the B or RETURN  
key.  
Setting items  
Picture  
Picture Mode  
Reset  
Standard  
Contrast  
Brightness  
Color  
80  
50  
50  
50  
Hue  
Color Temp.  
Sharpness  
Expert Setting  
Low  
30  
Contrast  
:Sel  
:Set  
:Back  
Back  
Adjust  
4 Make the setting or adjustment for the  
selected item.  
5 Press the MENU key to clear the  
The setting method varies, depending on  
the setting item.  
If the next menu window is displayed,  
select the item according to the  
menu.  
The menu disappears automatically if no  
operation is performed.  
14 Using a MENU  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
The Picture Menu  
The Picture is used to adjust the picture for each input signal.  
Items  
Item descriptions  
Picture Mode  
Dynamic: Emphasizes the contrast to produce a dynamic and vivid picture.  
Standard: Provides an image which is natural and well balanced.  
*1  
Presentation : Provides a bright image, suitable for presentations.  
Blackboard: Provides an image suitable for displaying on a blackboard.  
Game: Provides an image suitable for viewing games.  
Cinema: Provides an image suitable for viewing movies.  
*2  
Reset  
Resets to the factory setting.  
Contrast  
The higher the value, the greater the contrast. The lower the value, the lower  
the contrast.  
Brightness  
The higher the value, the brighter the picture. The lower the value, the darker  
the picture.  
*3 *4  
Color  
The higher the value, the greater the intensity. The lower the value, the lower  
the intensity.  
*3 *4 *5  
Hue  
The higher the value, the more greenish the picture becomes. The lower the  
value, the more reddish the picture becomes.  
*6  
Color Temp.  
High/Middle/Low: The higher the value, the more bluish the picture  
becomes. The lower the value, the more reddish the picture becomes.  
Sharpness  
The higher the value, the sharper the picture becomes. The lower the value, the  
softer the picture becomes.  
Expert Setting  
Gamma  
Graphics 1: Gamma correction to make halftones brighter. This setting is  
suitable when projecting highly colorful images, such as photos, in a bright  
place.  
*1 *7  
Mode  
Graphics 2: Gamma correction to improve the reproduction of halftones.  
Highly colorful images, such as photos, can be reproduced in natural tones.  
Text: Improves back and white contrast. Suitable for images with lots of text  
content.  
Notes  
*1: When a computer signal is input, this option is available.  
*2: The settings in the Picture return to their factory defaults, except for Picture Mode.  
*3: When a video signal is input, this option is available.  
*4: When the signal without color burst signal is input, this option is unavailable.  
*5: When an analog TV signal is input, this option may not available, depending on the color system.  
*6: When “Picture Mode” is set to the item other than “Presentation” or “Blackboard,” this option  
is available.  
*7: When “Picture Mode” is set to “Blackboard,” this option is unavailable.  
The Picture Menu 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
The Screen Menu  
The Screen menu is used to adjust the size, position and aspect ratio of the projected image for  
each input signal.  
Items  
Item descriptions  
*1  
Aspect  
Changes the aspect ratio of the projected image (page 18).  
VPL-DX140/DX120/ 4:3: Displays the image to fit the maximum projected image size  
DX100: When the  
computer signal is  
input  
with an aspect ratio fixed to 4:3.  
16:9: Displays the image to fit the maximum projected image size  
with an aspect ratio fixed to 16:9.  
Full 1: Displays the image to fit the maximum projected image  
size without changing the aspect ratio of the input signal.  
Normal: Displays the image on the center position of the  
projected image without changing the resolution of the input  
signal or enlarging the image.  
VPL-DX140/DX120/ 4:3: Displays the image to fit the maximum projected image size  
DX100: When the  
video signal is input  
with an aspect ratio fixed to 4:3.  
16:9: Displays the image to fit the maximum projected image size  
with an aspect ratio fixed to 16:9.  
Zoom: Zooms the center area of a projected image.  
VPL-DW120: When  
4:3: Displays the image to fit the maximum projected image size  
the computer signal is with an aspect ratio fixed to 4:3.  
input  
16:9: Displays the image to fit the maximum projected image size  
with an aspect ratio fixed to 16:9.  
Full 1: Displays the image to fit the maximum projected image  
size without changing the aspect ratio of the input signal.  
Full 2: Displays the image to fit the maximum projected image  
size changing the aspect ratio of the input signal.  
Full 3: Displays the image to fit the maximum width or height, up  
to 1280 × 720 pixels, without changing the aspect ratio of the  
input signal.  
Normal: Displays the image on the center position of the  
projected image without changing the resolution of the input  
signal or enlarging the image.  
VPL-DW120: When  
the video signal is  
input  
4:3: Displays the image to fit the maximum projected image size  
with an aspect ratio fixed to 4:3.  
16:9: Displays the image to fit the maximum projected image size  
with an aspect ratio fixed to 16:9.  
Full: Displays the image to fit the maximum projected image size  
changing the aspect ratio of the input signal.  
Zoom: Zooms the center area of a projected image.  
16 The Screen Menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Items  
Item descriptions  
Adjust Signal  
Adjusts the image of a computer signal. Use this item if the edge  
of the image is cut, or is not displayed properly.  
*2 *3  
APA  
Automatically adjusts the projected image to an optimum quality  
when you press the ENTER key (page 5).  
*2  
Phase  
Adjusts the dot phase of the display pixel and the input signal. Set  
to the value where looks clearest.  
*2  
Pitch  
The higher the value, the wider the horizontal image elements  
(pitch). The lower the value, the narrower the horizontal image  
elements (pitch).  
*2  
Shift  
H (Horizontal): The higher the value, the farther right the image  
is projected on the screen. The lower the value, the image farther  
left.  
V (Vertical): The higher the value, the farther up the image is  
projected on the screen. The lower the value, the image farther  
down.  
Notes  
*1: • Note that if the projector is used for profit or for public viewing, modifying the original picture  
by switching to the aspect mode may constitute an infringement of the rights of authors or  
producers, which are legally protected.  
• Depending on the input signal, setting items for aspect ratio or some other setting items cannot  
be set in some cases, or changing the aspect ratio setting may have no effect.  
• A part of the image may be displayed in black, depending on the setting item.  
*2: Available when a computer signal is input from the RGB input connector (INPUT A).  
*3: If the projected image includes large amount of black portion around it, the APA function will  
not work properly and a part of the image may not be displayed on the screen and also optimum  
image cannot be obtained, depending on the type of input signal. In this case, adjust the “Phase,”  
“Pitch,” and “Shift” items manually.  
The Screen Menu 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Aspect  
*1: If you select “Normal,” the image is  
projected in the same resolution as the  
input signal without changing the aspect  
ratio of the original image.  
VPL-DX140/DX120/DX100  
Input signal  
Recommended  
setting value and  
projected image  
*1  
4:3  
Full1  
*2: If you select “4:3,” the image is projected  
to fit the projected image size, regardless  
of the aspect ratio of the image.  
*1 *2  
16:9  
Full1  
*3: Depending on the input signal, the  
projected image may be projected as  
illustrated below. In this case, select  
“16:9.”  
*1 *2  
16:10  
Full1  
*3  
4:3  
4:3  
*4: Depending on the input signal, the  
projected image may be projected as  
illustrated below. In this case, select  
“Zoom.”  
*4  
16:9  
16:9  
18 The Screen Menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
*1: If you select “Normal,” the image is  
projected in the same resolution as the  
input signal without changing the aspect  
ratio of the original image.  
VPL-DW120  
Input signal  
Recommended  
setting value and  
projected image  
*1 *2 *3  
4:3  
16:9  
16:10  
Full1  
*2: If you select “Full2,” the image is projected  
to fit the projected image size, regardless  
of the aspect ratio of the image.  
*1 *2 *3  
Full1  
*3: If you adjust the projected image position  
using an image with 16:9 aspect ratio and  
then switch the input source to 4:3 image,  
the top and bottom edge of the image may  
be hidden. In this case, select “Full3.”  
*3  
Full1  
*4 *5  
4:3  
4:3  
*4: Depending on the input signal, the  
projected image may be projected as  
illustrated below. In this case, select  
“16:9.”  
16:9  
16:9  
*5: Depending on the input signal, the image  
may be projected as illustrated below. In  
this case, select “Zoom.”  
The Screen Menu 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Function Menu  
The Function menu is used for setting various functions of the projector.  
Items  
Item descriptions  
Volume  
The higher the value, the louder an audio volume and the lower the  
value, the lower the audio volume.  
Smart APA  
CC Display  
On/Off: When set to “On,” APA functions automatically when a  
*1  
signal is input.  
Off: Closed caption does not appear.  
CC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4: Select the closed  
caption service (captions or text).  
Lamp Timer Reset  
When replacing the lamp, resets the lamp timer (page 29).  
Note  
*1: APA functions when a computer signal is input via the RGB input connector (INPUT A).  
20 The Function Menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
The Operation Menu  
The Operation menu is used for setting for the operations by using the menu or the remote  
commander.  
Items  
Item descriptions  
Language  
Status  
Selects the language used in the menu and messages.  
On: All on-screen statuses are enabled.  
Off: Turns off the on-screen displays, except for menus, warning messages  
and messages from the message list.  
*1  
Security Lock  
On/Off: This function enables restriction of the projector to authorized users  
by password. The setting procedures for security locking are as follows:  
1 Select “On” and press the ENTER key to display the setting menu.  
2 Input the password with the MENU, V/v/B/b and ENTER keys. (The  
default setting password is “ENTER, ENTER, ENTER, ENTER.”)  
3 Input a new password with the MENU, V/v/B/b and ENTER keys.  
4 Enter the password again to confirm.  
Enter the password when you turn on the projector after disconnecting and  
reconnecting the AC power cord.  
When it is set to “Off,” you can cancel the security lock. You are required to  
input the password again.  
If you fail to enter the correct password after three consecutive times, the  
projector cannot be used. In this case, press the ?/1 key to go Standby mode  
then turn on the power again.  
Control Key  
Lock  
On/Off: When set to “On,” locks all the control panel keys of the projector.  
However, you can operate the following when set to “On”:  
• Press and hold the ?/1 key for approximately 10 seconds during Standby  
mode.  
c The projector turns on.  
• Press and hold the MENU key for approximately 10 seconds during power  
on.  
c “Control Key Lock” is set to “Off” and enables operation of all keys on  
the projector.  
Note  
*1: You will not be able to use the projector if you forget your password. If you call qualified Sony  
personnel because you have forgotten the password, you will be asked to verify the projector’s  
serial number and your identity. (This process may differ in other countries/regions.) Once your  
identity has been confirmed, we will provide you with the password.  
The Operation Menu 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
The Connection/Power Menu  
The Connection/Power menu is used for setting for the connections and power.  
Items  
Item descriptions  
*1  
Input-A Signal Sel.  
Auto/Computer/Video GBR/Component: When set to “Auto,” selects  
the type of video signal input automatically when “Input-A” is selected.  
ECO  
*5  
Lamp Mode  
High/Standard/Low/Auto : When set to “High,” the image becomes  
brighter, and power consumption becomes higher. When set to “Low,”  
power consumption is minimized; however, the image will be darker.  
When set to Auto,” brightness is adjusted automatically according to  
image content. Dark images are projected with brightness adjusted,  
leading to energy-saving. Bright images are projected brightly, without  
adjusting brightness.  
Auto Power Saving  
With No Input  
Lamp Cutoff: The lamp turns off automatically and power  
consumption is reduced if no signal is input for more than 10 minutes.  
The lamp lights again when a signal is input or any key is pressed. In  
Lamp Cutoff, the ON/STANDBY indicator lights in orange. (page 25)  
Standby : If no signal is input to the unit for more than 10 minutes,  
the power turns off automatically, and the unit enters standby mode.  
*2  
Off: You can deactivate the With No Input.  
*4*5  
With Static  
Signal  
Lamp Dimming  
: If an image does not change for about  
10 seconds, lamp output is gradually reduced (approximately 10% to  
15% ) from that set in the Lamp Mode. Automatically the lamp slowly  
*3  
darkens to approximately 30% of its lamp output according to the  
selected time (with no change to input signal) “5,” 10,” “15,” “20”  
minutes or “Demo.,” While dimming the lamp, the message “Lamp  
Dimming” appears. If you select “Demo.,” the image will start to  
darken about 40 seconds later. When any change in signal is detected,  
or an operation (remote control or control panel) is performed, normal  
brightness is restored.  
Off: You can deactivate the With Static Signal.  
Direct Power On  
On/Off: When set to “On,” you can turn the power on without going to  
Standby mode when the AC power cord is connected to a wall outlet.  
With the projector turned off, you can also unplug the AC power cord  
without going to Standby mode, regardless of the Direct Power On  
setting.  
Notes  
*1: This may not be optimum depending on the input signal. In this case, set manually according to  
the connected equipment.  
*2: Select “Off” to avoid entering standby mode when there is no input signal.  
*3: This varies depending on the “Lamp Mode” setting.  
*4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only  
notice that the lamp has dimmed when its brightness is restored after there is a change in input  
signal.  
*5: This mode does not work for about three minutes after the lamp lights. A change in signal may  
not be detected depending on the input image. The lamp may become brighter at intervals if you  
continue to use the projector during lamp dimming. However, this is not a malfunction. If With  
No Input is set, it takes priority.  
22 The Connection/Power Menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
The Installation Menu  
The Installation menu is used for installing the projector.  
Items  
Item descriptions  
Image Flip  
HV/H/V/Off: Flips the projected image horizontally or vertically  
according to the installation method.  
Installation Attitude Right Side Up/Upside Down/Link to Image Flip: Change the cooling  
setting to suit to the installation attitude. When set to “Link to Image Flip,”  
the cooling setting changes based on the setting of “Image Flip.”  
Continuing to use the wrong setting may affect component reliability.  
High Altitude  
Mode  
On/Off: Set to “On” when using the projector at an altitude of 1,500 m or  
higher. Continuing to use the wrong setting may affect component  
reliability.  
*1  
*2  
*3  
*2  
V keystone  
Auto /Manual : The higher the value, the narrower the top of the  
projected image. The lower the value, the narrower the bottom.  
Notes  
*1: When “High Altitude Mode” is set to “On,” the speed of the fan increases, and the fan noise  
becomes slightly louder.  
*2: Since the Keystone adjustment is an electronic correction, the image may be deteriorated.  
*3: VPL-DX140/DX120/DW120 only.  
The Installation Menu 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
The Information Menu  
The Information menu is used to check projector status, such as total usage time of the lamp.  
Items  
Item descriptions  
Model Name  
Serial No.  
Displays the model name.  
Displays the serial number.  
*1  
fH/fV  
Displays the horizontal/vertical frequency of the current input signal.  
Displays the type of the current input signal.  
Indicates the total usage time of a lamp.  
Signal Type  
Lamp Timer  
Note  
*1: These items may not be displayed depending on the input signal.  
24 The Information Menu  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
B Others  
Indicators  
The indicators allow checking the status and notify you of abnormal operation of the projector.  
If the projector exhibits abnormal status, address the problem in accordance with the table  
below.  
ON/STANDBY indicator  
Status  
Meaning/Remedies  
Lights in red  
Flashes in green  
The projector is in Standby mode.  
• The projector is ready to operate after having been turned on.  
• The lamp cools after the projector is turned off.  
Lights in green  
Lights in orange  
Flashes in red  
The projector’s power is on.  
The projector is in With No Input (Lamp Cutoff). (page 22)  
The projector is in abnormal status. Symptoms are indicated by  
number of flashes. Address the problem in accordance with the  
following. If a symptom persists, despite having taken measures  
below, consult with qualified Sony personnel.  
Flashes twice  
The internal temperature is unusually high. Check the items below.  
• Check if nothing is blocking the ventilation holes. (pages 3, 3)  
• Check if the air filter is not clogged. (page 31)  
• Check if the Installation Attitude in the Installation menu is set  
correctly. (page 23)  
Flashes six times Unplug the AC power cord from a wall outlet. After checking that the  
ON/STANDBY indicator goes out, plug the power cord to a wall  
outlet again then turn on the projector.  
Other number of  
flashes  
Consult with qualified Sony personnel.  
LAMP/COVER indicator  
Status  
Meaning/Remedies  
Flashes in red  
Symptoms are indicated by number of flashes. Address the problem in  
accordance with the following.  
Flashes twice  
The lamp cover is not attached securely. (page 29)  
Flashes three times The temperature of lamp is unusually high. Turn off the power and  
wait for lamp to cool then turn on the power again. If the symptom is  
shown again, the lamp may be burnt out. In this case, replace the lamp  
with a new one (page 29).  
Indicators 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Messages List  
When any of the messages listed below appears on the projected image, address the problem in  
accordance with the table below.  
Messages  
Meaning/Remedy  
Page  
High temp.! Lamp off in Check the items below.  
3, 3,  
1 min.  
• Check if nothing is blocking the ventilation holes.  
• Check if the air filter is not clogged.  
• Check if the Installation Attitude in the Installation menu is  
set correctly.  
Frequency is out of  
range!  
Change the output setting of the connected equipment to one  
for signals supported by the projector.  
Please check Input-A  
Signal Sel.  
Set “Input-A Signal Sel.” to “Auto” or select the input signal  
type to suit to the input signal.  
Please clean the filter.  
Clean the air filter.  
Please replace the Lamp Replace the lamp with a new one and clean the air filter. The  
and clean the Filter.  
message appears whenever you turn on the power until you  
replace the lamp and reset the lamp timer.  
Not applicable!  
Invalid key was pressed.  
The control keys are  
locked!  
“Control Key Lock” is set to “On.”  
Projector will shutdown The ?/1 key was pressed and the projector will be shut down  
soon soon. To cancel shutdown, press the ?/1 key again (the  
Press ?/1 Key to Restart projector will remain on). To turn off the projector directly,  
press and hold the ?/1 key for a few seconds.  
Lamp Dimming  
Reduces lamp output when “With Static Signal” is set. When  
any change in signal is detected, or an operation (remote  
control or control panel) is performed, normal brightness is  
restored.  
26 Messages List  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Troubleshooting  
Before asking to have the projector repaired, try to diagnose the problem, following the  
instructions below.  
Symptoms  
Remedy  
Page  
The power is not turned Check if the AC power cord is firmly connected.  
on.  
When the “Control Key Lock” is set to “On,” you cannot turn  
on the projector using the ?/1 key on the projector.  
If the lamp or lamp cover is not attached securely, the projector  
cannot be turned on.  
No image.  
Check if the connecting cable is connected to external  
equipment firmly.  
Check the computer signal is set for output to an external  
monitor only. If you set your computer to output to both the  
computer’s display and an external monitor, the external  
monitor image may not be displayed properly. Set your  
computer to output to only an external monitor.  
Check if the input source is correctly selected.  
Check if the picture is muted.  
On-screen display does The on-screen display does not appear when “Status” in the  
not appear.  
Operation menu is set to “Off.”  
The aspect ratio of the  
display is not right/the  
image is displayed  
The image may not display correctly because the input signal 5, 16,  
cannot be judged correctly. In this case, set “Aspect” manually. 18  
smaller /a portion of  
image does not appear.  
The image is a  
trapezoid.  
The images become trapezoidal because of the projection  
angle. In this case, you can correct the trapezoidal distortion, 23  
using a Keystone feature.  
5, 12,  
When the “V Keystone” is set to “Manual,” the keystone  
feature does not work automatically. Set “V Keystone” to  
“Auto” or “Manual” to set manually.  
5, 12,  
*1  
When the projector is installed on an uneven surface, the  
keystone feature may not work properly. In this case, select 23  
“Manual” to set “V Keystone” manually.  
5, 12,  
*1  
Troubleshooting 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Symptoms  
Remedy  
Page  
The image is dark/too  
bright.  
The settings for “Brightness,” “Contrast,” and “Lamp Mode”  
affect brightness of the image. Check if the value is  
appropriate.  
The image will be dark when the lamp is burnt out. Check  
“Lamp Timer,” and replace the lamp with a new one if  
necessary.  
“With Static Signal” is set to “On.”  
During picture muting, the lamp is dimmed to reduce power  
consumption.  
When video signal is not input, the lamp is dimmed to reduce  
power consumption.  
The image becomes  
darker or brighter.  
When the lamp is dimmed for a long time, brightness may  
increase temporarily, but this is not malfunction.  
When the “Lamp Mode” is set to “Auto,” the luminance of the  
lamp changes according to the input image.  
The image is not clear.  
Check if the projector is in focus.  
The picture will not be clear if condensation has accumulated  
on the lens. In this case, let the projector sit for about two  
hours with the power on.  
The image is noisy.  
No sound.  
Check if the connecting cable is connected to the external  
equipment properly.  
Check that the connecting cables between the projector and  
external video or audio equipment are securely connected.  
Check if the external audio equipment is set properly.  
Audio is not output if audio muting is activated.  
Check if the volume is not set to minimum.  
The remote commander Check if the batteries are installed correctly.  
does not work.  
Check if the batteries are not exhausted.  
The fan is noisy.  
The sound from the fan is often greater than normal to cool the 22, 23  
lamp, etc. in the following cases.  
• “Lamp Mode” is set to “High.”  
• The unit is used at a high altitude. “High Altitude Mode” is  
set to “On.”  
• The unit is used in the location where the temperature is high.  
If the ventilation holes are blocked, the internal temperature of  
the projector rises and the fan noise becomes larger.  
Note  
*1: VPL-DX140/DX120/DW120 only.  
28 Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Lamp  
Replace the lamp with a new one if a message displayed on the projected image (page 26).  
Use an LMP-D213 projector lamp (not supplied) for replacement.  
Caution  
1 Turn off the projector, and disconnect  
• The lamp remains hot after the projector is  
turned off. If you touch the lamp, you may  
burn your finger. When you replace the  
lamp, wait for at least an hour after  
turning off the projector for the lamp to  
cool sufficiently.  
the AC power cord from a wall outlet.  
2 When the lamp has cooled  
sufficiently, open the lamp cover by  
loosening one screw.  
• Do not allow any metallic or inflammable  
objects into the lamp replacement slot after  
removing the lamp, otherwise it may cause  
electrical shock or fire. Do not put your  
hands into the slot.  
Notes  
If the lamp breaks, contact qualified  
Sony personnel. Do not replace the lamp  
yourself.  
• When removing the lamp, be sure to pull it  
out straight, by holding the designated  
location. If you touch a part of the lamp other  
than the designated location, you may be  
burned or injured. If you pull out the lamp  
while the projector is tilted, the pieces may  
scatter if the lamp breaks any may cause  
injury.  
Note  
For safety reasons, do not loosen any other  
screws.  
3 Loosen the two screws on the lamp  
unit (1). Fold out the handle (2),  
then pull out the lamp unit by the  
handle (3).  
Fold out the handle.  
3
1
2
1
Replacing the Lamp 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Caution  
6 Connect the AC power cord to a wall  
outlet and turn on the projector.  
Do not put your hands into the lamp  
replacement slot, and do not allow any  
liquid or other objects into the slot to avoid  
electrical shock or fire.  
7 Reset the lamp timer for notification of  
the next replacement time.  
Select “Lamp Timer Reset” on the  
Function menu then press the ENTER  
key. When a message appears, select  
Yes” to reset the lamp timer (page 20).  
4 Insert the new lamp all the way in until  
it is securely in place (1). Tighten the  
two screws (2). Fold down the handle  
to replace it (3).  
Caution  
Disposal of the used lamp  
For the customers in the USA  
Lamp in this product contains mercury.  
Disposal of these materials may be  
regulated due to environmental  
considerations. For disposal or  
recycling information, please contact  
your local authorities or the  
Telecommunications Industry  
Association (www.eiae.org).  
Fold down the handle.  
1
2
3
2
Notes  
• Be careful not to touch the glass surface  
of the lamp and a inside conductor.  
• Insert the handle firmly to attach it  
securely.  
• The power will not turn on if the lamp is  
not secured properly.  
5 Close the lamp cover and tighten the  
1 screw.  
30 Replacing the Lamp  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the Air Filter  
When a message appears on the projected image indicating time for a filter cleaning, clean the  
air filter (page 26).  
If the dust cannot be removed from the air filter even after cleaning, replace the air filter with  
a new one. For details on purchasing/fitting a new air filter, consult with the store where you  
purchased the projector, or contact qualified Sony personnel.  
Caution  
If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the  
temperature may rise inside the unit, leading to a possible malfunction or fire.  
1 Turn off the projector, and disconnect  
3 Clean the air filter with a vacuum  
the AC power cord from the AC outlet.  
cleaner.  
Pull out and remove the air filter, and  
clean it with a vacuum cleaner.  
2 Slide out and remove the air filter  
cover from the unit.  
Claws  
Air filter  
Air filter cover  
4 Reattach the air filter cover to the unit.  
Note  
Install the air filter with its open weave side  
facing the bottom of the unit, then place the  
air filter cover back in the unit.  
Cleaning the Air Filter 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Specifications  
Items  
Descriptions  
Model  
VPL-DX140/DX120/DX100/VPL-DW120  
3 LCD system  
Projection system  
Display device  
Effective display VPL-DX140/DX120/DX100: 0.63 inch (16.0 mm),  
size  
3 plate panels, Aspect ratio 4:3  
VPL-DW120: 0.59 inch (15.0 mm), 3 plate panels,  
Aspect ratio 16:10  
Effective picture VPL-DX140/DX120/DX100: 2,359,296 pixels (1024 ×  
elements  
768 pixels, 3 plate panels)  
VPL-DW120: 3,072,000 pixels (1280 × 800 pixels,  
3 plate panels)  
Projection lens  
Light source  
Zoom  
Manual zoom:  
VPL-DX140/VPL-DW120: approx.1.3 times  
VPL-DX120/DX100: approx.1.2 times  
Focus  
Manual  
High-pressure mercury lamp, 210 W type  
30 inches to 300 inches (0.76 m to 7.62 m)  
Projected image  
size  
Luminous flux  
(Brightness)  
VPL-DX140: 3200 lm  
VPL-DX120/VPL-DW120: 2600 lm  
VPL-DX100: 2300 lm  
(when “Lamp Mode” is set to “High”)  
Speaker  
1 W × 1 (monaural)  
Applicable  
scanning  
frequency  
Horizontal: 15 kHz to 92 kHz, Vertical: 48 Hz to 92 Hz  
*1  
*1  
Resolution  
When a computer Maximum display resolution: 1600 × 1200 pixels (resize)  
signal is input  
Panel display resolution:  
VPL-DX140/DX120/DX100: 1024 × 768 pixels  
VPL-DW120: 1280 × 800 pixels  
When a video  
signal is input  
NTSC, PAL, SECAM, 480/60i, 576/50i, 480/60p,  
576/50p, 720/60p, 720/50p, 1080/60i, 1080/50i,  
1080/60p, 1080/50p  
Color system  
NTSC3.58, PAL, SECAM, NTSC4.43, PAL-M, PAL-N  
32 Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Items  
Descriptions  
Model  
VPL-DX140/DX120/DX100/VPL-DW120  
INPUT OUTPUT INPUT A  
(Computer/video)  
RGB/YPBPR input connector: Mini D-sub 15 pin  
female, G with sync/Y: 1 Vp-p 2 dB, sync negative,  
75 ohms terminated, RGB/PBPR: 0.7 Vp-p 2 dB,  
75 ohms terminated, Sync signal: TTL level high  
impedance, positive/negative  
Audio input connector: Stereo mini jack, rated input  
500 mVrms, input impedance more than 47 kohms  
INPUT B  
VIDEO  
HDMI input connector: HDMI 19-pin, HDCP, HDMI  
audio support  
Video input connector: Pin jack, 1 Vp-p 2 dB, sync  
negative, 75 ohmes terminated  
Audio input connector: Shared with INPUT A  
Operating  
temperature/  
Operating  
humidity  
0 °C to 35 °C (32 °F to 95 °F)/20% ~ 80% (no  
condensation)  
Storage  
temperature/  
Storage humidity  
–10 °C to +60 °C (14 °F to 140 °F)/20% to 80% (no  
condensation)  
Power  
100V to 240V AC, 2.9 - 1.2 A, 50/60Hz  
requirements  
Power  
consumption  
100V to 120V AC: 290W  
220V to 240V AC: 275W  
Standby power  
Heat dissipation  
0.5 W  
100V AC: 936BTU  
240V AC: 955BTU  
13  
7
3
Standard  
dimensions  
(W/H/D)  
Approx. 315 × 87.2 × 233 mm (12 /32 × 3 /16 × 9 /16  
inches)  
13  
15  
Approx. 315 × 75 × 230.5 mm (12 /32 × 2 /16 ×  
1
9 /16 inches) (without projecting parts)  
Mass  
Approx. 2.5 kg (5 lb 7 oz)  
Supplied  
accessories  
See “Checking the Supplied Accessories” in the supplied  
Quick Reference Manual.  
Optional  
accessories  
Projector Lamp LMP-D213 (for replacement)  
*2 *3  
Notes  
*1: For details, refer to “Acceptable Input Signals*1” on page 36.  
*2: Information on accessories in this manual is current as of June 2012.  
*3: Not all optional accessories are available in all countries and area. Please check with your local  
Sony Authorized Dealer.  
Specifications 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Design and specifications of the unit, including the optional accessories, are subject to change  
without notice.  
Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE  
FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,  
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT  
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING  
THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR  
ANY OTHER REASON WHATSOEVER.  
34 Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin assignment  
HDMI connector (HDMI, female)  
RGB input connector (Mini D-sub  
15-pin, female)  
19  
1
18  
2
1
2
3
4
5
6
7
8
9
T.M.D.S.  
Data2+  
11 T.M.D.S.  
Clock Shield  
T.M.D.S.  
Data2 Shield  
12 T.M.D.S.  
Clock –  
1
2
3
Video input  
(red) R  
9
Power supply  
input for DDC  
T.M.D.S.  
Data2 –  
13 N.C.  
Video input  
(green) G  
10 GND  
T.M.D.S.  
Data1+  
14 RESERVED  
(N.C.)  
Video input  
(blue) B  
11 GND  
T.M.D.S.  
Data1 Shield  
15 SCL  
4
5
GND  
12 DDC/SDA  
RESERVE  
13 Horizontal sync  
signal  
T.M.D.S.  
Data1 –  
16 SDA  
6
GND (R)  
14 Vertical sync  
signal  
T.M.D.S.  
Data0+  
17 DDC  
GND  
7
8
GND (G)  
GND (B)  
15 DDC/SCL  
T.M.D.S.  
Data0 Shield  
18 +5V Power  
T.M.D.S.  
Data0 –  
19 Hot Plug  
Detect  
10 T.M.D.S.  
Clock+  
Specifications 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Acceptable Input Signals*1  
Computer signal  
Input connector  
fH[kHz]/  
fV[Hz]  
Resolution  
RGB/  
HDMI  
YPBPR  
Input connector  
z
z
1280 × 800  
49.7/60  
fH[kHz]/  
fV[Hz]  
Resolution  
RGB/  
HDMI  
Digital TV signal*4  
YPBPR  
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
640 × 350  
31.5/70  
37.9/85  
31.5/70  
37.9/85  
31.5/60  
35.0/67  
37.9/73  
37.5/75  
43.3/85  
35.2/56  
37.9/60  
48.1/72  
46.9/75  
53.7/85  
49.7/75  
48.4/60  
56.5/70  
60.0/75  
68.7/85  
64.0/70  
67.5/75  
77.5/85  
61.8/66  
60.0/60  
Input connector  
Signal  
fV[Hz]  
RGB/  
HDMI  
YPBPR  
640 × 400  
640 × 480  
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
480i  
576i  
60  
50  
60  
50  
60  
50  
60  
50  
60  
50  
z
480p  
576p  
1080i  
1080i  
720p  
720p  
1080p  
1080p  
800 × 600  
z
832 × 624  
Analog TV signal  
z
1024 × 768  
Input connector  
Signal  
fV[Hz]  
VIDEO  
z
NTSC  
60  
50  
z
PAL/SECAM  
1152 × 864  
Notes  
*1: When a signal other than the signals listed  
in table is input, the picture may not be  
displayed properly.  
• An input signal meant for screen  
resolution different from that of the panel  
will not be displayed in its original  
resolution. Text and lines may be uneven.  
*2: This is identified as a movie delivery signal  
of 720/60p.  
1152 × 900  
1280 × 960  
z
z
1280 × 1024 64.0/60  
80.0/75  
91.1/85  
z
z
z
1400 × 1050 65.3/60  
1600 × 1200 75.0/60  
*3: This is identified as a movie delivery signal  
of 1080/60p.  
*4: Only G with sync/Y is supported.  
1280 × 768  
1280 × 720  
47.8/60  
45.0/60  
*2  
z
z
*3  
1920 × 1080 67.5/60  
z
z
z
z
z
1366 × 768  
1440 × 900  
47.7/60  
55.9/60  
36 Specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Projection Distance  
The projection distance is the distance between the front of the lens and the surface of the  
projected image. The following describes the projection distance and height from the center of  
the lens to edge of screen by each projected screen size. Height H is the height from the bottom  
of the projected image (top for ceiling mount) to A (determined by drawing a perpendicular line  
from the center of the lens to projected image surface).  
Caution  
Never mount the projector on the ceiling or move it by yourself. Be sure to consult with  
qualified Sony personnel (charged).  
Floor Installation  
Projection distance L  
Projected  
image  
Center of lens  
Height H from  
center of lens  
to edge of  
screen  
A
Projection Distance 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Ceiling Installation  
Height H from center of  
lens to edge of screen  
Center of lens  
A
Top side  
Projected  
image  
Projection distance L  
L: Projection distance L  
H: Height H from center of lens to edge of screen  
38 Projection Distance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projection distance table (VPL-DX140)  
Unit: m (inches)  
Height H from center of lens to edge  
of screen  
Projected image size  
Projection  
Distance L  
Minimum  
Projection  
Distance L  
Maximum  
Projection  
Distance L  
Diagonal D  
Width × Height  
80 inch (2.03 m)  
1.63 × 1.22  
(64 × 48)  
2.25-2.92 (89-115)  
2.81-3.66 (111-144)  
3.38-4.40 (133-173)  
4.23-5.51 (167-217)  
5.65-7.36 (223-289)  
-0.20 (-8)  
-0.25 (-10)  
-0.30 (-12)  
-0.38 (-15)  
-0.51 (-20)  
-0.20 (-8)  
-0.25 (-10)  
-0.30 (-12)  
-0.38 (-15)  
-0.51 (-20)  
100 inch (2.54 m) 2.03 × 1.52  
(80 × 60)  
120 inch (3.05 m) 2.44 × 1.83  
(96 × 72)  
150 inch (3.81 m) 3.05 × 2.29  
(120 × 90)  
200 inch (5.08 m) 4.06 × 3.05  
(160 × 120)  
Projection distance formula (VPL-DX140)  
D: Projected image size (Diagonal)  
H: Height H from center of lens to edge of screen  
Expression#1  
Unit: m (inches)  
Minimum Projection Distance L  
Maximum Projection Distance L  
L=0.028366 × D-0.0290  
(L=1.116781 × D-1.1416)  
L=0.036956 × D-0.0283  
(L=1.454972 × D-1.1124)  
Expression#2  
Height H from center of lens to edge of screen  
Minimum Projection Distance L  
Maximum Projection Distance L  
H=-0.00254 × D+0.00000  
(H=-0.10000 × D+0.00000)  
H=-0.00254 × D+0.00000  
(H=-0.10000 × D+0.00000)  
Projection Distance 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projection distance table (VPL-DX120/DX100)  
Unit: m (inches)  
Height H from center of lens to edge  
of screen  
Projected image size  
Projection  
Distance L  
Minimum  
Projection  
Distance L  
Maximum  
Projection  
Distance L  
Diagonal D  
Width × Height  
80 inch (2.03 m)  
1.63 × 1.22  
(64 × 48)  
2.42-2.88 (95-113)  
3.02-3.60 (119-141)  
3.63-4.33 (143-170)  
4.55-5.42 (179-213)  
6.07-7.23 (239-284)  
-0.20 (-8)  
-0.25 (-10)  
-0.30 (-12)  
-0.38 (-15)  
-0.51 (-20)  
-0.20 (-8)  
-0.25 (-10)  
-0.30 (-12)  
-0.38 (-15)  
-0.51 (-20)  
100 inch (2.54 m) 2.03 × 1.52  
(80 × 60)  
120 inch (3.05 m) 2.44 × 1.83  
(96 × 72)  
150 inch (3.81 m) 3.05 × 2.29  
(120 × 90)  
200 inch (5.08 m) 4.06 × 3.05  
(160 × 120)  
Projection distance formula (VPL-DX120/DX100)  
D: Projected image size (Diagonal)  
H: Height H from center of lens to edge of screen  
Expression#1  
Unit: m (inches)  
Minimum Projection Distance L  
Maximum Projection Distance L  
L=0.030427 × D-0.0234  
(L=1.197898 × D-0.9193)  
L=0.036301 × D-0.0236  
(L=1.429177 × D-0.9283)  
Expression#2  
Height H from center of lens to edge of screen  
Minimum Projection Distance L  
Maximum Projection Distance L  
H=-0.00254 × D+0.00000  
(H=-0.10000 × D+0.00000)  
H=-0.00254 × D+0.00000  
(H=-0.10000 × D+0.00000)  
40 Projection Distance  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projection distance table (VPL-DW120)  
Unit: m (inches)  
Height H from center of lens to edge  
of screen  
Projected image size  
Projection  
Distance L  
Minimum  
Projection  
Distance L  
Maximum  
Projection  
Distance L  
Diagonal D  
Width × Height  
80 inch (2.03 m)  
1.72 × 1.08  
(68 × 42)  
2.36-3.05 (93-120)  
2.95-3.82 (117-150)  
3.55-4.59 (140-180)  
4.44-5.75 (175-226)  
5.93-7.67 (234-302)  
-0.20 (-8)  
-0.25 (-10)  
-0.29 (-12)  
-0.37 (-15)  
-0.49 (-19)  
-0.20 (-8)  
-0.25 (-10)  
-0.29 (-12)  
-0.37 (-15)  
-0.49 (-19)  
100 inch (2.54 m) 2.15 × 1.35  
(85 × 53)  
120 inch (3.05 m) 2.58 × 1.62  
(102 × 64)  
150 inch (3.81 m) 3.23 × 2.02  
(127 × 79)  
200 inch (5.08 m) 4.31 × 2.69  
(170 × 106)  
Projection distance formula (VPL-DW120)  
D: Projected image size (Diagonal)  
H: Height H from center of lens to edge of screen  
Expression#1  
Unit: m (inches)  
Minimum Projection Distance L  
Maximum Projection Distance L  
L=0.029757 × D-0.0291  
(L=1.171525 × D-1.1450)  
L=0.038536 × D-0.0282  
(L=1.517164 × D-1.1091)  
Expression#2  
Height H from center of lens to edge of screen  
Minimum Projection Distance L  
Maximum Projection Distance L  
H=-0.00246 × D+0.00000  
(H=-0.09675 × D+0.00000)  
H=-0.00246 × D+0.00000  
(H=-0.09675 × D+0.00000)  
Projection Distance 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Top  
13  
315 (12 /32)  
VPL-DX120/DX100  
Edge of lens  
VPL-DX140/DW120  
Edge of lens  
Unit: mm (inches)  
Front  
3
157.5 (6 /16)  
3
81 (3 /16)  
1
26 (1 /32)  
Unit: mm (inches)  
42 Dimensions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Side  
23  
7
69 (2 /32)  
113 (4 /16)  
23  
7
69 (2 /32)  
31 (1 /32)  
Unit: mm (inches)  
Rear  
21  
15  
16.8 ( /32)  
164.4 (6 /32)  
3
28 (1 /32)  
3
157.5 (6 /16)  
15  
252.5 (9 /16)  
Unit: mm (inches)  
Dimensions 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bottom  
3
17  
78.9 (3 /32)  
38.8 (1 /32)  
76.4 (3)  
15  
15  
88.5 (3 /32)  
23.9 ( /16)  
21  
7
271 (10 /32)  
22 ( /8)  
Unit: mm (inches)  
44 Dimensions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
H
Index  
A
Air filter cover/Ventilation holes  
I
K
B
L
C
Correcting trapezoidal distortion of the  
M
O
D
P
E
F
R
G
Index 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
S
About Trademarks  
• Adobe and Adobe Acrobat are trademarks  
or registered trademarks of Adobe  
Systems Incorporated in the United States  
and/or other countries.  
• Kensington is a registered trademark of  
Kensington Technology Group.  
• The terms HDMI and HDMI High-  
Definition Multimedia Interface, and the  
HDMI Logo are trademarks or registered  
trademarks of HDMI Licensing LLC in  
the United States and other countries.  
• All other trademarks and registered  
trademarks are trademarks or registered  
trademarks of their respective holders. In  
T
®
this manual, and marks are not  
specified.  
U
V
W
Z
46 Index  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sony Corporation  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Indoor Furnishings AN 65AG1 User Manual
Sharp Projector XG PH50X User Manual
Sony Camera Lens 16mm F 28 User Manual
Sony Car Stereo System CDX M600 User Manual
Sony CRT Television KV T21 KV T25 KV 2168 User Manual
Sony Digital Camera 3 700 727 121 User Manual
Sony Microcassette Recorder CFS E14 User Manual
Sony MP3 Docking Station RDPXF100IP User Manual
Spalding Fitness Equipment M8660411 User Manual
Sylvania MP3 Player SMPK2077 User Manual