Savin All in One Printer 7700W User Guide

Operating Instructions

Zfbh010e.eps

Read this manual carefully before you use this product and keep it handy for future

reference.

For safety, please follow the instructions in this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sa fe ty Inform a tion

When using your equipment, the following safety precautions should always be

followed.

Safety During Operation

In this manual, the following important symbols are used:

R WARNING:

Indicates a potentially hazardous situation which, if instructions

are not followed, could result in death or serious injury.

R CAUTION:

Indicates a potentially hazardous situation which, if instructions are not

followed, may result in minor or moderate injury or damage to property.

Download from Www.Somanuals.com. All Manuals Search And Download.

R WARNING:

•

Connect the power cord directly into a wall outlet and never use an extension cord.

Only connect the machine to the power source described on the inside front cover of this man-

ual.

•

Avoid multi-wiring.

Do not damage, break or make any modifications to the power cord. Do not place heavy ob-

jects on it, pull it hard or bend it more than necessary. These actions could cause an electric

shock or fire.

•

Do not plug or unplug the power cord with your hands wet. Otherwise, an electric shock

might occur.

Disconnect the power plug (by pulling the plug, not the cable) if the power cable or plug be-

comes frayed or otherwise damaged.

Make sure the wall outlet is near the machine and freely accessible so that in event of an emer-

gency it can be unplugged easily.

Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any

of the following conditions exists:

•

You spill something into the equipment.

You suspect that your equipment needs service or repair.

Your equipment's cover has been damaged.

•

Do not take apart or attempt any modifications to this machine. There is a risk of fire, electric

shock, explosion or loss of sight. If the machine has laser systems, there is a risk of serious eye

damage.

•

To avoid hazardous electric shock or laser radiation exposure, do not remove any covers or

screws other than those specified in this manual.

Some parts of the machine are at a high voltage and could give you an electric shock. Also, if

the machine has laser systems, direct (or indirect) reflected eye contact with the laser beam

may cause serious eye damage. When the machine needs to be checked, adjusted, or repaired,

contact your service representative.

•

Do not keep using the machine with a fault or defect. Contact your service representative.

If the machine looks damaged or breaks down, smoke is coming out, there is a strange smell

or anything looks unusual, immediately turn off the operation and main power switches then

unplug the power cord from the wall. Do not continue using the machine in this condition.

Contact your service representative.

•

Do not put any metal objects or containers holding water (e.g. vases, flowerpots, glasses) on

the machine. If the contents fall inside the machine, a fire or electric shock could occur.

Do not incinerate spilled toner or used toner. Toner dust might ignite when exposed to an

open flame.

•

Disposal can take place at our authorized dealer or at appropriate collection sites.

Dispose of the used toner cartridge in accordance with the local regulation.

Download from Www.Somanuals.com. All Manuals Search And Download.

R CAUTION:

•

When you pull out the plug from the socket, grip the plug to avoid damaging the cord and

causing fire or electric shock.

•

Unplug the power cord from the wall outlet before you move the equipment. While moving

the equipment, you should take care that the power cord will not be damaged under the

equipment.

•

When the machine will not be used for a long time, unplug the power cord.

If you use the machine in a confined space, make sure there is a continuous air turnover.

Keep the machine away from humidity and dust. A fire or an electric shock might occur.

Do not place the machine on an unstable or tilted surface. If it topples over, it could cause in-

jury.

•

After you move the machine, fix it with the caster fixture. Otherwise, the machine might move

or come down to cause a personal injury.

•

Protect the equipment from dampness or wet weather, such as rain, snow, and so on.

Do not allow paper clips, staples, or other small metallic objects to fall inside the equipment.

Do not reuse stapled paper. Do not use aluminum foil, carbon-containing paper or other con-

ductive paper. Otherwise, a fire might occur.

•

Do not eat or swallow toner.

Keep toner (used or unused) and toner bottle out of the reach of children.

For environmental reasons, do not dispose of the equipment or expended supply waste at

household waste collection points. Disposal can take place at an authorized dealer or at ap-

propriate collection sites.

•

When removing misfed paper, do not touch the fusing section because it could be very hot.

Do not touch the anti-humidity switch from inside the machine because it could be very hot.

The inside of the machine could be very hot. Do not touch the parts with a label indicating the

“hot surface”. Otherwise it could cause a personal burn.

•

Rolls of paper can be heavy, so you should be careful when loading one.

This machine has been tested for safety using this supplier's parts and consumables. We rec-

ommend you only use these specified supplies.

•

Our products are engineered to meet high standards of quality and functionality, and we rec-

ommend that you only use the expendable supplies available at an authorized dealer.

This equipment is only to be installed by a qualified service personnel.

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

ENERGY STAR Prog ra m

As an ENERGY STAR Partner, we have determined

that this machine model meets the ENERGY STAR

Guidelines for energy efficiency.

The ENERGY STAR Guidelines intend to establish an international energy-saving system for

developing and introducing energy-efficient office equipment to deal with environmental is-

sues, such as global warming.

When a product meets the ENERGY STAR Guidelines for energy efficiency, the Partner shall

place the ENERGY STAR logo onto the machine model.

This product was designed to reduce the environmental impact associated with office equip-

ment by means of energy-saving features, such as Low-power mode.

• Auto Off Mode

To conserve energy, this product automatically turns off 1 minutes after the

last copying or printing job has been completed. Printing is available in this

mode, but if you use the copier, press the main switch.

For how to change the default interval before entering Auto Off mode, see

“Auto Off Time”⇒ P.38 “User Tools”

❖ Specification

FW770

Auto Off

mode

Power con-

sumption

1.0 W

Default interval

30 minute

-Re c yc le d Pa p e r

Please contact your sales or service representative for recommended recycled

paper types that may be used in this machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

How to Re a d this Ma nua l

Symbols

In this manual, the following symbols are used:

R WARNING:

This symbol indicates a potentially hazardous situation that might result in

death or serious injury when you misuse the machine without following the in-

structions under this symbol. Be sure to read the instructions, all of which are de-

scribed in the Safety Information section.

R CAUTION:

This symbol indicates a potentially hazardous situation that might result in mi-

nor or moderate injury or property damage that does not involve personal injury

when you misuse the machine without following the instructions under this

symbol. Be sure to read the instructions, all of which are described in the Safety

Information section.

* The statements above are notes for your safety.

Important

If this instruction is not followed, paper might be misfed, originals might be

damaged, or data might be lost. Be sure to read this.

Preparation

This symbol indicates the prior knowledge or preparations required before op-

erating.

Note

This symbol indicates precautions for operation, or actions to take after misop-

eration.

Limitation

This symbol indicates numerical limits, functions that cannot be used together,

or conditions in which a particular function cannot be used.

Reference

This symbol indicates a reference.

[

]

Keys that appear on the machine's panel display.

{

}

Keys built into the machine's operation panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Guide to Components............................................................................... 1

Copier Exterior .............................................................................................. 1

Operation Panel ............................................................................................ 3

1.Ba sic s

Turning on the Power................................................................................ 5

Turn On the Main Power............................................................................... 5

Turn Off the Main Power............................................................................... 5

Recommended Originals.......................................................................... 6

Non-recommended Originals ........................................................................ 7

Notes for Leading and Side Edge of the Originals ........................................ 7

Recommended Paper................................................................................ 8

Anti-humidity Heater...................................................................................... 9

Toner......................................................................................................... 10

Handling Toner............................................................................................ 10

Toner Storage ............................................................................................. 10

Used Toner ................................................................................................. 10

2.Cop ying

Basic Copying (Copying to sheets)....................................................... 11

Using the Roll Feeder (Option) ................................................................... 15

Using the Rear Table .................................................................................. 17

Copying onto Roll Paper (Option).......................................................... 19

Semi Synchro cutting .................................................................................. 19

Preset Cutting ............................................................................................. 22

Variable Cutting........................................................................................... 23

Using The Roll Cutting Rail (Option)........................................................... 25

3.Cop y Se tting s

Copying Onto Other Media..................................................................... 27

Adjusting the Fusing Temperature Manually............................................... 28

Adjusting Copy Image Density............................................................... 29

Making Several Copies of the Same Original ....................................... 30

Setting a Leading Edge Margin.............................................................. 31

Partial Copying ........................................................................................ 32

Programming Settings You Often Use .................................................. 35

A) Program key ........................................................................................... 35

B) Changing the Default Setting.................................................................. 36

User Tools................................................................................................ 38

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings You Can Change with User Tools........................................... 40

4.Ma inta ining Your Cop ie r

Changing The Used Toner Bottle........................................................... 45

Adding Toner........................................................................................... 48

Changing The Roll Paper Size................................................................ 52

Removing the Roll Paper Holder................................................................. 52

Setting the Roll Paper Holder...................................................................... 52

Loading A Roll Of Paper......................................................................... 54

Loading A New Roll Onto Paper Cutting Rail (Option) ........................ 59

5.Troub le shooting

If Something Goes Wrong ...................................................................... 61

If Indicator Lights Up ................................................................................... 61

If Jams Occur........................................................................................... 62

If the Original is Jammed at the Exit ........................................................... 62

If Sheet Paper is Jammed in the Feed-in Slot............................................. 63

If Sheet Paper is Jammed at the Paper Exit ............................................... 64

If Roll Paper Jams....................................................................................... 65

If You Cannot See the Roll Paper Jam ....................................................... 67

Others....................................................................................................... 70

Absolutely nothing happens........................................................................ 70

Something happens, but Set Paper or RF Select never appear................. 70

If Jams Occur Frequently............................................................................ 70

If Copies Look Wrong.................................................................................. 70

White Spots Appear .................................................................................... 70

Creases....................................................................................................... 71

Copies Come Out Dog Eared ..................................................................... 71

Black streaks appear on copies .................................................................. 71

Daily Maintenance ................................................................................... 72

Clean the Exposure Glass & the Platen Plate............................................. 72

Do's & Don'ts ........................................................................................... 73

Where to Put Your Copier....................................................................... 74

Machine Environment ................................................................................. 74

Power Connection....................................................................................... 75

Access To Machine..................................................................................... 76

6.Sp e c ific a tions

Copier....................................................................................................... 77

Options..................................................................................................... 78

INDEX........................................................................................................ 79

vii

Download from Www.Somanuals.com. All Manuals Search And Download.

viii

Download from Www.Somanuals.com. All Manuals Search And Download.

Guid e to Com p one nts

Copier Exterior

1. Locks

5. Operation Panel

Squeeze both locks(1a&1b) to open the

unit. Open the unit to empty the used

toner bottle and to remove jammed pa-

per.

⇒ P.3 “Operation Panel”.

6. Rear Table

Place stiff originals face down here.

7. Roll Feeder (option)

2. Front Cover

Open the cover (and the unit) to access

the toner cartridge.

Feeds paper from a roll to the copier.

8. Paper Guides

Use the guides to keep the copy paper

straight as you feed it into the copier.

3. Original Table

Place your original face up here. If you

want to copy a stiff original that can't be

bent, use the rear table (see 6).

9. Bypass Table

Use this table when you want to make

copy one by one.

4. Original Guides

Use th e gu id e to keep th e origin al

straight as you feed the original into the

copier.

10. Table (option)

Holds your copier and the Roll Feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

11. Main switch

13. Anti-humidity Heater Switch

Use this switch to turn the copier on and

off. The copier will need about 3 minutes

to warm up, if it's been turned off for a

long time.

When humidity is high, the paper in the

paper roll tray m ay absorb m oistu re,

w hich can effect the im age qu ality of

your copies. The anti-humidity heater

prevents this. Turn on this switch, which

is located rear left corner of the machine,

when humidity is high.⇒ P.9 “Anti-hu-

midity Heater”

12. Copy Exit Guide

Makes sure the copies don't fall off as

they come out.

Note

❖ Set the manual pocket as shown in the

figure.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation Panel

1. Function indicators

These indicators show which setting you

are currently editing, Press the Function

key to cycle through them.

6. Troubleshooting indicators

⇒ P.61 “Troubleshooting” for details.

7. Wait indicator

Shows that the copier is not yet ready to

copy.

•

The top indicator (Paper Length indi-

cator) lights when the paper length is

being set.

8. Ready (d), Set Original(R), Set

Paper (K), Bypass Select (a) indica-

tor.

When Ready indicator lights up, you can

set paper.The Set Paper indicator on the

left lights, and then Bypass Select indica-

tor goes on.

The middle indicator (Leading Edge

ind icator) lights w hen the lead ing

margin is being set.

The bottom indicator (Copy Counter

indicator) lights when the number of

copies is being set.

2. Paper Length display

Shows the length of paper the Roll Feeder

will send.

9. {Clear Modes/Energy Saver} key

Cancels all of current settings. When you

hold down this key for three seconds or

more, the copier enters the Energy Saver

mode allowing you to conserve power.

3. {Preset Cut} key

Press to scrolls through the preset paper

lengths for the Roll Feeder.

To exit Energy Saver mode, press this key

again.

4. {Cut Select} key

Turns Semi synchro Cut or Preset/ Varia-

ble Cut on and off.

10. {Program} key

Allows you to recall or set a program.

The program indicator(LED) lights after

you store the setting.

5. Energy Saver indicator

Shows that the machine is in a state of

wait (Energy Saver). Press key 9.

Download from Www.Somanuals.com. All Manuals Search And Download.

11. {Function Select} key

Press to change which setting you are ed-

iting. The current selection is shown by

the indicators above the key:

19. {Paper Feed}key

Press to feed the paper.

Pap er Feed ind icator(LED) lights u p

when the machine is ready to feed roll

paper.

•

Paper Length

Leading Edge

Copy Counter

20. {Clear/Stop} key

When entering numbers, press to cancel.

Also used for copying a selected portion

of the original.

While copying, press to stop copying.

12. {+} and {—} key

Press to increase the value being edited.

Press to decrease the value being edited.

13. Leading Edge/Copy Counter in-

dicator

Displays the m argin settings and the

number of copies made.

14. Roll Feeder indicator

Light up when you select Roll Feeder 1 or

15. {RF Select/Cut} key

Use to select the paper feed type (when

the Roll Feeder option is installed). Also

press to stop a copy job.

16. {Copy Media} key

Press to select the type of copy paper you

are using.

The copier will apply more or less heat

accordingly.

•

The top indicator-Translucent paper

indicator

•

The bottom indicator-Film indicator

17. {Emergency Stop} key

Press to stop the copying process imme-

diately.

Use if your original is getting stuck in the

copier.

If you stop operation by pressing this

key, remove both the original and paper.

18. D en sity in d icator an d {i},

{j}keys

Shows the density level the copies will

have.

Press the left key to make copies lighter.

Press the right key to make copies darker.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Ba sic s

Turning on the Powe r

To turn the machine on, press the

main switch.

Turn On the Main Power

A Make sure that the power cord is

firmly plugged into the wall out-

let.

B Turn on the main switch.

Turn Off the Main Power

A Turn off the main switch.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basics

Re c om m e nd e d Orig ina ls

• You can set originals with weight in the range 21g/ m²(6 lb) to 157 g/ m²(41

lb).

• You can set original with sizes between 914×3,000mm (W×L), 36"×118" and

210×297mm (W×L), 8.5"×11". (The maximum width that can be fed: 960mm,

38.4")

• Fix the curl of originals to within the following range.

• For the curl of the leading edge and the trailing edge: R50mm (2.0") or

more, H20mm (0.8") or less

• For the curl of the whole paper: φ30mm (1.2") or more

• When you copy the following originals, set them in the rear table:

⇒ P.17 “Using the Rear Table”

• Thick originals (0.19mm~3mm)

• Originals which cannot be folded.

• Originals less than 297mm (11") in width and more than 1,200mm (48") in

length.

• When you copy the following originals, use the Carrier Sheet (option) to set

them:

• Piled originals

• Folded originals

• Taped or pasted originals

• Originals which have a hole near the leading edge 40mm (1.6") to the right

or left of the center

• Dog-eared originals

• Creased, torn, or clipped-out originals

• Wavy originals

• Pasted originals

• Originals whose leading edge is not straight

• Curled originals

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommended Originals

Non-recommended Originals

• The following types of originals are not recommended.

• Wet originals

• Originals with cardboard stuck on the leading edge

• Originals with clips or staples

• Originals with wet ink or white-out

• Carbon paper

• Originals made of materials other than paper or film

(thermosensitive paper, aluminum foil, etc.)

Notes for Leading and Side Edge of the Originals

Margins on the leading and side edges of originals are not copied as shown in

the illustration.

• a=0±3mm (0.12”)

• b1+b2<0±2mm (0.08”) (A1L)

Download from Www.Somanuals.com. All Manuals Search And Download.

Basics

Re c om m e nd e d Pa p e r

• Standard paper sizes that can be used in this copier are shown below.

Metric version

Inch version

E (36"×48")

D (24"×36")

C (18"×24")

B (12"×18")

A (9"×12")

Bypass

Roll Feeder

• When you make a copy on a non-standard size of paper, set the paper on the

Copy Paper Table.

• Weight of paper suitable for this copier: 51g/ m², 14lb to 134g/ m², 36lb.

• Do not use the following kinds of paper or a paper jam might occur.

• Bent, folded, or creased paper

• Torn paper

• Perforated paper

• Non-smooth paper

• Slippery paper

• Thin paper that has low stiffness

• Do not make a copy on paper with any kind of coating, such as thermosensi-

tive paper, art paper, aluminum foil, and carbon paper.

A fault might occur.

• Do not use paper with strong curls at the edges or corners. (Curls rising more

than 5mm (1/ 4") or falling more than 20mm (3/ 4") over a 40mm (1.5") radius.)

• When you make copies on film, take out the copies delivered to the copy

guide one sheet at a time and place them on a flat surface.

• If copying to natural tracing paper (all pulp, translucent paper) at a relative

humidity of 35% or less

^AIf the paper was left out of its package for 5 minutes or more, remove the

first 1000mm (39.3") before copying.

^BIf copies come out wavy or with white spots, use translucent paper instead

of natural tracing paper.

^CAlways keep the paper in a bag when not using it.

• Store the paper in a sealed polyvinyl bag if not used for a long period.

If it gets humid, paper will curl or wave which can cause a paper jam or part

of the image not to be copied.

Download from Www.Somanuals.com. All Manuals Search And Download.

Recommended Paper

• When you use paper in high humidity under hot conditions, take out only the

necessary amount of paper from the bag. Do not take all the paper out of the

bag.

Anti-humidity Heater

• When humidity is high, the paper in the paper roll tray may absorb moisture,

which can effect the image quality of your copies. The anti-humidity heater

prevents this. Set this switch to "On" when the humidity reaches more than

45%.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basics

Tone r

Handling Toner

R WARNING:

• Do not incinerate used toner, toner bottle or toner cartridge.

• Toner dust might ignite when exposed to an open flame.

• Dispose of the used toner and the used toner cartridge ac-

cording to local regulations.

R CAUTION:

• Do not eat or swallow toner.

• Keep toner (used or unused), toner bottle, and toner cartridge out

of reach of children.

R CAUTION:

• This machine has been tested for safety using this supplier's

parts and consumables. We recommend you only use these

specified supplies.

• If you use toner other than that recommended, a fault might occur.

• If you want to add toner, ⇒ P.48 “Adding Toner”

Toner Storage

• Store toner cartridges horizontally in a cool, dark place.

• Do not leave toner cartridges in your car on a hot day for a long period of

time, or anywhere that they could be subjected to temperatures of over 95°F

(35°C).

• Never store toner where it will be exposed to heat.

• Do not lay heavy objects on toner bottles.

Used Toner

• Toner cannot be re-used.

• Put the used toner in the plastic bag and dispose of it according to local reg-

ulations.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Cop ying

Ba sic Cop ying (Cop ying to she e ts)

Use bypass table or roll feeder to copy onto paper.

Note

❖ For acceptable types of original and paper,⇒ P.6 “Recommended Originals”

and ⇒ P.8 “Recommended Paper”.

❖ If you use bypass table, place one sheet of paper at a time on the bypass table

and never insert more than one sheet of paper.

❖ If the copy paper is curled, place it with the curl facing downwards.

❖ When you set A0 size (36"×48") paper, to make sure the ends do not touch the

floor and get dirty, lay a wide piece of paper or some other covering on the

floor.

❖ Do not use paper which is cut obliquely, when the difference between the

right side and the left side of the paper is more than 5mm (1/ 5"), creasing or

a paper jam might occur.

❖ You cannot copy to both sides of the paper at the same time.

❖ The machine needs about 3 minutes to warm up after being turned on before

copies can be made. The machine is warming up when the Wait indicator is

lit, but you can still edit settings, insert copy paper or insert your original.

❖ Set paper, and then set original (from bypass tray or roll feeder). When you

have set both of them, the copier starts copying automatically.

❖ Do not lean on the copy table or lay heavy objects on it.

❖ After finish copying, you can store up to 25 copies.

R CAUTION:

• If during copying your original gets stuck in the copier, press the

{Emergency Stop} key.

• If you stop operation by pressing this key, remove both the origi-

nal and paper.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

A Turn on the main switch.

B Make sure that the Wait indicator goes off, and then Ready and the Set Pa-

per indicator go on.

Make sure that the Bypass Tray is selected.

C Select any copy settings you require, such as the media type or copy densi-

ty.

D Set the paper guide to match the width of the paper.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Copying (Copying to sheets)

E Slide the paper straight into the copier until it stops. The copier will soon

pull it in.

Note

❖ Center the paper face up on the bypass table and slide the paper straight

into the copier.These illustrations show the copier w ith the Original

Guides, the Paper Guides, and other optional equipment.

F Make sure that the Set Original indicator goes on.

G Set the Original Guides to match the original size mark. Set the original

face up and slide it straight into the copier along the Original Guides.

H The original comes out from the opening just under the original table (A).

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

The copy is delivered from the slot on top of the copier (B).

If you make several copies of the same original, when the copy comes out, re-

move it and repeat from step C

Note

❖ If you want to catch copies at the back of the machine, change the copy de-

livery direction as shown in the figure.

Note

I Do not hold down or pull out the original during copying. Do not put

heavy object on the original table.

❖ If you do not insert the original in a certain interval after inserting the pa-

per, the paper will be ejected automatically.

❖ If the copier is idle at a certain time after you have used it, the machine re-

sets itself to the initial settings (Auto Reset). If the copier is not used for a

long time, it will turn itself off (Auto Off ).

❖ You can preset the initial settings of the copier ⇒ P.36 “B) Changing the De-

fault Setting”

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Copying (Copying to sheets)

Using the Roll Feeder (Option)

A When the Wait indicator goes off and the Ready and the Set Paper indicator

go on, the copier enters the ready condition.

Make sure that the paper feed indicator lights up.

B Select any copy settings you require, such as the media type or copy densi-

ty.

Press the {RF Select/Cut} key to select the Roll Feeder.

Note

❖ If you select two roll feeder (option), select one of the roll.

C Press the {Paper Feed} key.

D Open the guides to keep the edge of the original from slipping into the pa-

per entrance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

E Make sure that the Set Original indicator goes on.

F Set the original guides to match the width of the original.

G Center your original face up on the original Table. Slide the original

straight into the copier until the copier pulls it in.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic Copying (Copying to sheets)

H The original comes from the opening just under the Original Table (A).

The copy is delivered from the slot on top of the copier (B).

Using the Rear Table

When you copy the following originals, set them in the Rear Table.

• Thick originals (0.19mm ~ 3mm).

• Originals which cannot be folded.

• Originals less than 297mm (11") in width and more than 1,200mm (48") in

length.

Note

❖ You cannot use the following functions when using the Rear Table.

• Semi Synchro Cut with roll paper

• Partial Copying

A Choose any copy setting you require.

B For manual copying, set paper.

C Pull up the holder and turn in the copy exit guide.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

D Insert the original face down from the rear table.

E Hold and take the original which has been read and delivered in the front

of the copier.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying onto Roll Paper (Option)

Cop ying onto Roll Pa p e r (Op tion)

The paper will be fed to the copier from the Roll Feeder. You can copy onto roll

paper using the following functions:

• Semi Synchro cutting

• Preset cutting

• Variable cutting

Note

❖ If unused roll paper is left in the copier, cut 1000mm (39.4") from the edge of

the paper before you start copying.

❖ When you want to copy a long original, curled original, or the thin original

(less than 0.1mm) which can be easily bent down, open the guides to keep the

original away from the paper entrance.

R CAUTION:

• If during copying your original gets stuck in the copier, press the

{Emergency Stop} key.

• If you stop operation by pressing this key, remove both the origi-

nal and paper.

Semi Synchro cutting

This feature lets you cut the roll paper manually to a length that approximates

to that of the original. This saves you having to measure and enter the length of

every original.

Note

❖ Semi Synchro Cut can handle the cut length in the range 440 ~ 3000mm, 17.3"

~ 118.0".

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

❖ If you set the number of copies, Semi Synchro Cut can handle automatically

by the length at your setting for first copy.

❖ Do not use carrier sheet and rear table when you use Semi synchro cutting. A

fault might occur.

A Press the {Cut Select} key(1).

The Semi Synchro indicator lights up(2).

B Choose any copy settings you require.

C Make sure that the Wait indicator goes off and Ready and the Set Paper in-

dicator go on.

D Press the {RF Select/Cut} key to turn on the RF Select indicator.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying onto Roll Paper (Option)

E Press the {Paper Feed} key.

F Set the original guides to match the width of the original.

G Center your original face up on the original table. Slide the original straight

into the copier until the copier pulls it in.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

H Just as the trailing edge of the original passes the table edge, press the {RF

Select/Cut} key.

Important

❖ To cancel copying, press the {Clear/Stop} key. The copier finishes the oper-

ation in progress, and delivers the copy and the original.

❖ To cancel on-going copying, for example, when you have inserted a wrong

blueprint, press the {RF Select/Cut} key. The machine interrupts the opera-

tion in progress, and delivers the copy and the original.

❖ If you make copy without pressing the {RF Select/Cut}key, copied paper

might come out with originial size + 310mm.

❖ When you repeat the copy job with this function even if you select different

sizes of the originals, this function helps you to make same size copy.

❖ Once you set the cut length and press the {RF Select/Cut} key to enter the

repeat copy cycle, do not press the key. Otherwise, the copy job will be in-

terrupted. If you want to repeat the copy job again, press the {Paper Feed}

key. For details about job settings, seeD.

Preset Cutting

This function cuts roll paper to a selected length. The paper is cut to this length

regardless of the original size.

Note

❖ The default Preset Cut length is as follows. Metric Version: 1189mm, 841mm,

594mm, 420mm, 297mm Inch Version: 48.0", 42.0", 36.0", 24.0", 18.0", 11.0". To

change of the Preset Cut length pattern, please contact your service represent-

ative.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying onto Roll Paper (Option)

A Press the {Preset Cut} key (1).

The Preset/Variable indicator lights up (2) and the Paper Length display

shows the default preset cut length. (1189mm or 48.0").

B Press the {Preset Cut} key several times until the indicator shows the value

you want.

C Choose any copy settings you require.

D Press the {RF select/Cut} key to turn on the RF Select indicator.

Continue from step E,F⇒ P.21

Variable Cutting

This function cuts roll paper in a length you specify.

Note

❖ Length can be cut length from 280mm to 3,000mm, 11" to 118".

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

A Press the {Preset Cut} key(1). The Preset/Variable indicator(2) lights up and

the "Paper Length" display shows the default Preset Cut length. (1189mm

or 48").

B Press the {Preset Cut} key to display the nearest value to the one you want.

C Press {+} key or {−} key to specify the most appropriate length.

You can change the settings by 1mm (0.1”) steps.

D Choose any copy settings you require.

E Press the {RF Select/Cut} key to turn on the RF Select indicator.

Continue from step E⇒ P.21

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying onto Roll Paper (Option)

Using The Roll Cutting Rail (Option)

The Roll Cutting Rail allows you to use roll paper and cut your own sheets. For

how to set the roll cutting rail, ⇒ P.59 “Loading A New Roll Onto Paper Cutting

Rail (Option)”

A Pull a bit of paper out and insert it between the rail and the double rod.

B Pull the length of paper you want.

C With one hand, hold the paper firmly against the Original Table.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copying

D With your other hand, insert the blade of a paper knife between the two

rods and slide across the length of the rail.

E Make your copy as shown on ⇒ P.27. Make sure the curl of the paper faces

down.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Cop y Se tting s

Cop ying Onto Othe r Me d ia

To copy onto translucent or tracing paper or film, use the {Copy Media} key to

match the paper type refer to the following table.

Type of paper

Plain paper

Film

Media setting

Both indicators off

Film indicator on

Translucent paper

Heavy paper

Thin paper

Translucent indicator on

No indicator or the film indicator if necessary.

If you are not sure of what type of paper you have, check the label on the paper

package to confirm it.

A Press the {Copy Media} key to turn on the Translucent or Film indicator.

The Wait indicator goes on and either the Translucent or Film indicator

lights.

B When the wait indicator goes off and the Ready and the Set Paper indicator

go on, the copier enters the ready condition.

Note

❖ Even if you have set the Copy Media function correctly, creasing might oc-

cur depending on the temperature or humidity. If this happens, adjust the

fusing temperature manually. See the next page.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Adjusting the Fusing Temperature Manually

A Press the {Copy Media} key to turn on the Translucent or Film indicator that

you want.

B Hold down the {Copy Media} key for 3 seconds until beep. The indicator

show the current fusing temperature. The unlit indicator shows the current

temperature settings.

C Press the {i} key to decrease the temperature, and press the {j} key to

increase the temperature. The number of temperature levels (7 levels)

available depends on the paper type:

• Plain paper : 1234567

• Translucent paper: 1234

• Film : 1234

D After you have finished setting the temperature, press the {Copy Media} key.

E Choose any copy settings you require, and then start copying.

Note

❖ The new fusing temperature for the selected paper type is cleared when

you press the {Clear Modes/Energy Saver} key or turn off the main switch.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting Copy Image Density

Ad justing Cop y Im a g e De nsity

To make copies darker or lighter, change the density setting. There are 14 densi-

ty levels (=7 notches × 2).

• Standard density level (Default)

• 3 darker levels

• 10 lighter levels

Set the density with the {i} and {j} keys under the density indicator.

Note

❖ The indicator shows seven levels at a time. When you start from the standard

image density, the middle notch corresponds to the standard image density,

the three right notches correspond to darker densities, and the three left

notches to lighter densities.

❖ The brighter notch shows which level is now set. If you go lower than the left-

most notch, the Lighter Copy indicator light up. The notches on the indicator

correspond to the seven lightest levels.

❖ If you change the copy image density while repeat copying, the next copy job

will come out with new setting.

A Press the {i} or {j} key to adjust copy density.

B Each time you press the {i} key, the indicator moves one step to the left.

When the indicator reaches the left edge, it returns to the right edge and the

Lighter Copy indicator lights.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Ma king Se ve ra l Cop ie s of the Sa m e

Orig ina l

You can preset the number of copies (1 to 99) you want to make. Repeated cop-

ying means making two or more copies of an original. To make more than one

copy of the original, you have to reload the original after each copy. If you do

not have the optional Roll Feeder, you have to set the copy paper for each copy.

Note

❖ You can preset up to 99.

❖ Do not press the {RF Select/Cut} key twice once you start preset cut with this

function. If you press the key twice, the copy job will be interrupted.

A Press the {+} and {−} keys to specify the number of copies.

When you press the {Clear/Stop} key, the number of copies returns to "1".

B Proceed as usual for a copy, with sheet paper (⇒ P.11), or with the Roll

Feeder (⇒ P.19).

C When the copy comes out, remove it and repeat step B. Wait for the Set Pa-

per indicator to light up before loading a new sheet of paper, and wait for

the Set Original indicator to light up before reloading the original.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting a Leading Edge Margin

Se tting a Le a d ing Ed g e Ma rg in

You can set a margin at the leading edge of the copy.

Leading Edge Margin

Leading Edge

Margin

In the Semi Synchro Cut mode

Using the Copy Paper Table, or in the Preset Cut mode,

Variable cut mode

Note

❖ You can set up to a ±99mm, ±4.0" margin in 1mm, 0.1" steps at the leading

edge.

❖ The copy image is shifted to the trailing edge, when you make a copy using

the bypass table, or in the Preset Cut mode or Variable Cut mode.

❖ In the Semi Synchro Cut mode, the paper length is increased by the leading

margin width.

A Press the {Function Select} key until the Leading Edge indicator is lit.

B Press the {+} key and {−} key to specify an edge margin.

To zero the value, press the {Clear/Stop} key.

C Insert the original from the leading edge.

You can get same results using the Rear Table.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Pa rtia l Cop ying

The Partial Copy function copies only a part of an original.

You need to enter start and end points in the feed direction of the original .

Note

❖ You cannot use the Partial Copying function when using the Rear Table.

❖ You cannot use the Partial Copying function for originals shorter than

150mm.

❖ You can use the Partial Copying function for originals longer than 1270mm.

❖ If you set the start point within 130 mm of the leading edge of the original, the

copier will regard the leading edge as the start point.

❖ The minimum available space between the start point and the end point is 30

mm.

❖ If you do not set the end point after setting the start point (a), the copier will

regard the trailing edge of the original as the end point (b).

❖ If you do not set the end point in the Semi Synchro Cutting function, the pa-

per extend by 200mm from the end point (from c to d). The paper extend by

310mm from the trailing edge.

A Hold down the {Function Select} key for three seconds or more.

A "P" will blink in the copy counter display.

Download from Www.Somanuals.com. All Manuals Search And Download.

Partial Copying

B Slide the paper straight into the copier until it stops, or press the {RF Select/

Cut} key to turn on the RF Select indicator.

C Place the original.

D Press the {Function Select} key when the leading edge of the area to be cop-

ied reaches the edge of the original table cover.

The "P" will stay on, not blinking.

The copier starts copying.

E Press the {Function Select} key when the trailing edge of the area to be cop-

ied reached the edge of the original table cover.

The "P" will start blinking again.

F After the paper has been delivered, hold down the {Function Select} key for

three seconds to turn the function off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

The "P" will disappear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming Settings You Often Use

Prog ra m m ing Se tting s You Ofte n Use

There are two ways of programming settings you often use.

A) Store the settings in the {Program} key. When you press this key, the settings

will be recalled instantly.

B) Change the default settings to those you use most frequently. Whenever you

turn on the machine or press the {Clear Modes/Energy Saver} key, these settings

will be ready to use.

A) Program key

Storing Setting in the Program Key

Note

❖ You can store one setting for frequently use.

A Press the {Program} key.

B Input the settings you want to store.

C Make a copy.

The machine memorizes the types of job setting.

D Press the {Program} key.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Recalling Settings Stored in the Program key

A Press the {Program} key before copying.

B Enter the number of copies required with the {+} and {—} key.

C Make a copy.

B) Changing the Default Setting

A Turn off the main switch.

B While holding down the {Emergency Stop} key, turn the copier back on.

The jam and service indicators will blink.

C Input the settings you want.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming Settings You Often Use

D Turn off the main switch.

Note

❖ The next time you turn the copier on, the settings you programmed in step

will take effect.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Use r Tools

Access the User Tools to make the following adjustments:

A1) Not in use

A2) Semi Synchro Cut Adjustment; Allows you to adjust the cut length.

−25mm ~ +25mm (−1.0" ~ −1.0") (by 1mm or 0.1")

Without the Roll Feeder, A2) is not in use.

A Hold down the {Program} key for 3 seconds or more.

"A1" blinks on the "Copy Counter" display.

B Press the {+} key, "A2" blinks on the display

C Press the {Function Select} key.

The Paper Length display shows the current value.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Tools

D Use the {+} and {−} key to change the value.

E Press the {Program} key to return to step

F Press the {Clear Modes/Energy Saver} key to exit this mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Se tting s You Ca n Cha ng e with Use r Tools

This section is for the key operators in charge of this machine. You can change

or set the machine's default settings.

Note

❖ For how to enter the User Tools program, press the {Clear Modes/Energy Saver}

key, and then press the {Clear/Stop} key for more than 3 seconds.

• Fusing Temperature 1–Normal(+01): Selects the fusing temperature for plain

paper.

Note

❖ 0: Mode 1, 1: Mode 2, 2: Mode 3, 3: Mode 4, 4: Mode 5, 5: Mode 6, 6: Mode 7

❖ Default: 2

❖ For details about each mode, contact your service representative.

• Fusing Temperature 2–High (+02): Selects the fusing temperature for trans-

lucent paper.

Note

❖ 0: Mode 5, 1: Mode 6, 2: Mode 7, 3: Mode 8

❖ Default: 0

❖ For details about each mode, contact your service representative.

• Fusing Temperature 3–Low(+03): Selects the fusing temperature for translu-

cent film.

Note

❖ 0: Mode 2, 1: Mode 3, 2: Mode 4, 3: Mode 5

❖ Default: 1

❖ For details about each mode, contact your service representative.

• Count Up/Down(+04): The copy counter can be made to count up or count

down.

Note

❖ 0: Count up, 1: Count down

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings You Can Change with User Tools

❖ Default: 0

• Beeper On/Off(+05): The beeper can be turned off completely; turned off for

setting the margin, multiple copies, and paper length; or left on to emit a tone

whenever a key is pressed.

Note

❖ 0: On, 1: All Off, 2: Partially Off

❖ Default: 2(The beeper does not work if you use leading edge margin.)

• Paper Feed Out Waiting Time Setting(+06): When the copier is ready to re-

ceive the original, it will wait for a preset length of time. If no original is set

within this time, the copier will process the copy paper without copying. The

time can be set to 1, 2, 3, 4, or 5 minutes.

Note

❖ 0: 2min, 1: 1min, 2: 3min, 3: 4min, 4: 5 min

❖ Default: 0

• Manual Feed Start Time Setting(+07): After the copy paper is set, the copier

waits for a preset number of seconds before starting the rollers that will pull

the paper in. This pause gives you a chance to align the paper. The time can

be set to 0.7, 1, 2, 3, 4, or 5 seconds.

Note

❖ 0: 2.0sec, 1: 0.7sec, 2: 1.0sec, 3: 3.0sec, 4: 4.0sec, 5: 5.0sec

❖ Default: 0

• Lead Edge Increase/Decrease Speed Setting(+08): The speed at which the

lead edge setting scrolls up or down can be changed. The time for one incre-

ment (or decrement) can be set to 0.02, 0.05, 0.10, 0.25, or 0.5 seconds.

Note

❖ 0: 0.10 sec, 1: 0.50 sec, 2: 0.25 sec, 3: 0.05 sec, 4: 0.02 sec

❖ Default: 0

• Auto Reset Time Setting(+09): If the copier is idle for a while, it will clear it-

self. The time needed can be set to 1, 2, 3, 4, or 5 minutes. This function can

also be turned off.

Note

❖ 0: 2 min, 1: 1min, 2: 3 min, 3: 4 min, 4: 5 min, 5: None

❖ Default: 0

❖ The machine cannot enter the Auto reset mode if the roll end indicator

lights while copying repeatedly.

❖ The machine cannot enter the Auto clear if the toner end indicator lights.

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

• Auto Energy Saver Mode(+10): The fusing unit needs to be hot for copying.

When the copier is idle, the fusing unit can be kept hot to save time or it can

be allowed to cool to save energy. This feature can be set to start automatical-

ly, but you can also turn it on yourself by pressing and holding the {Clear

Modes/Energy Saver} key for three seconds.

Note

❖ 0: None, 1: Yes

❖ Default: 0

❖ The machine can not enter the energy saving mode if toner end indicator

lights.

• Screen Message Setting(+11): When the copier is idle, the copy counter can

be made to display a message. There are five possible messages: "Pre_heat",

"Sleeping", "0123456789", “Have a good day", and "Hello I love you". This fea-

ture can also be turned off.

Note

❖ 0: None, 1: "Pre_heat", 2: "Hello I love you", 3: "0123456789", 4: "Sleeping" ,

5: Have a good day".

• Leading Edge Increase/Decrease Adjustment Preliminary Interval(+12):

When changing a function setting (margin, multiple copies, or paper length)

by holding down the {+} or {−} key, the setting will change by a preset value.

This value can be changed to 1, 2, 3, or 10 intervals.

Note

❖ 0: 3 intervals, 1: 1 interval, 2: 2 intervals, 3: 10 intervals

❖ Default: 0

• Auto Off Time(+15): You can set the time the machine waits after the last op-

eration before switching itself off automatically. The time can be set by

minute from 1 to 240 minutes.

Note

❖ Default: 30min

❖ Auto Off cannot be used in the following cases.

• When the Wait indicator goes on

• When the toner end indicator goes on

• When the front door is open

• While copying

• When a paper misfeed occurs or SC call appears

• The machine cannot enter the Auto Off mode if the roll end indicator

lights while copying repeatedly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings You Can Change with User Tools

• Semi-synchro Cut Original Scanning Mode(+18): Selects whether the roll

paper cut key must be pressed at the appropriate time when the trailing edge

of the original passes the Semi-synchro cut mark, or whether the original

must be inserted again after the original is scanned and the length is meas-

ured.

Note

❖ 0: Pressing the roll paper cut key, 1: Inserting the original again

❖ Default: 0

• Semi-synchro Cut Length Adjustment(+19): Adjust the cut length in the

semi-synchro cut mode.The setting can be changed from —25 to 25 by 1mm

steps.

Note

❖ Default: 0

• Paper Length Up/Down Setting(+20): Select if the paper length is count

down or up when the preset cut key is pressed.

Note

❖ 0: Down count, 1: Up count

❖ Default: 0

• Paper Length Up/Down Speed Setting(+21) :The copier can scroll through

the preset lengths forward or backward, and at different speeds. There are

many sets of sizes from which to choose.

Note

❖ 0: 0.10 seconds, 1: 0.5 seconds, 2: 0.25 seconds, 3: 0.05 seconds, 4: 0.02 sec-

onds, 5: 0.01 seconds

❖ Default: 0

• Fixed Paper Size Pattern Setting(+22): Select the fixed paper size pattern cho-

sen when the “Preset Cut” key is press. For details about this setting, contact

your service representative.

• Optional Paper Size Setting(+23 ~ +32): Up to 10 different paper size can be

stored from 23 to 32.For details about this setting, contact your service repre-

sentative.

• Auto Off Function setting(+33): This setting allows you to enable or disable

the Auto Off function.

Note

❖ 0: Disable, 1: Enable

❖ Default: 1

• Darker Image Density(+37): Sets the range of the ID density control to give

finer control over darker images.

— ID level 1 to 7-Darker image density and low contrast settings

—ID level 8 to 14-cannot be shifted

Download from Www.Somanuals.com. All Manuals Search And Download.

Copy Settings

Note

❖ 0: Standard Density 1: Darker Image Density

❖ Default: 0

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Ma inta ining Your Cop ie r

Cha ng ing The Use d Tone r Bottle

When E is displayed, it is time to change the toner bottle.

R WARNING:

• Do not incinerate used toner, toner bottle or toner cartridge.

• Toner dust might ignite when exposed to an open flame.

• Dispose of the used toner and the used toner cartridge ac-

cording to local regulations.

R CAUTION:

• Do not eat or swallow toner.

• Keep toner (used or unused), toner bottle, and toner cartridge out

of reach of children.

R CAUTION:

• This machine has been tested for safety using this supplier's

parts and consumables. We recommend you only use these

specified supplies.

Note

❖ If the toner bottle overflows, toner particles could get inside the copier and

cause damage. When you install a new bottle, make sure it is perfectly set in

its holder.

❖ Do not use used toner. This will damage the machine.

A Open the upper unit of the copier.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

B Unplug the code from the machine.

C Open the door on the right side of the copier, and then carefully remove the

plastic bottle.

Note

❖ Put the used toner to the plastic bag and dispose of it according to local reg-

ulations. Do not throw away the bottle.

D Place the bottle in the the copier again, and then close the door.

E Plug in the code to the mainframe.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing The Used Toner Bottle

F Close the upper unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

Ad d ing Tone r

When D is displayed, it is time to add toner.

When the indicator starts blinking, you can still copy about 53 feet of paper (16

m, 27 8¹/ "×11" size copies). When the indicator stays on, you can't copy until a

new cartridge is installed.

R WARNING:

• Do not incinerate used toner, toner bottle or toner cartridge.

• Toner dust might ignite when exposed to an open flame.

• Dispose of the used toner and the used toner cartridge ac-

cording to local regulations.

R CAUTION:

• Do not eat or swallow toner.

• Keep toner (used or unused), toner bottle, and toner cartridge out

of reach of children.

R CAUTION:

• This machine has been tested for safety using this supplier's

parts and consumables. We recommend you only use these

specified supplies.

Note

❖ If you use toner other than that recommended, a fault might occur.

❖ When adding toner, do not turn off the main switch. If you do, your settings

will be cleared.

❖ Always add toner after the machine instructs you to add toner.

❖ Do not use used toner. This will damage the machine.

A Lift the original table until it locks in place.

Note

❖ If your machine does not have roll feeder, pull down the Bypass Table first.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adding Toner

B Open the toner cartridge cover.

C Turn the old cartridge towards you.

Then, while pressing the cartridge to the right (A), lift the left end and re-

move the cartridge (B).

D Put the old toner cartridge in a plastic bag and dispose of it according to lo-

cal regulations.

E Shake the new toner cartridge lightly 5 to 6 times to remove lumps.

F Install the new cartridge. Make sure that the white circle labeled 1 on the

cartridge faces up.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

Make sure the cartridge is set well but don't push it in yet.

G Take the right edge of the seal and slowly remove it.

H Push the toner cartridge all the way to the left.

Then turn the toner cartridge all the way in, as shown.

Note

❖ If you can't close the toner cartridge cover, there might be problem setting

the toner cartridge. In this case, set the toner cartridge again.

I Close the toner cartridge cover and the original table.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adding Toner

The copier will need a few moments to warm up before it is ready to copy.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

Cha ng ing The Roll Pa p e r Size

Change the size guides on the left and

right of the roll paper holder when

you load different sized paper rolls.

Setting the Roll Paper Holder

A Insert the hook on the paper hold-

er into (A), an d th en insert the

protrusion into (B).

Important

❖ Always follow the instructions be-

low when adjusting the roll paper

holder. Do not force the roll paper

hold er by p u lling or slid ing it

strongly. This could damage the

holder.

Removing the Roll Paper

Holder

A Push the paper holder inwards,

an d th en p ull it u p w ard s to re-

move it.

Note

❖ Make sure the protrusions are

firmly in the hole.

❖ Lock the left side of the paper

Note

holder until it clicks.

❖ The paper holder is attached

with magnet and a hook.

B Match the paper size in the win-

dows .

❖ The paper holder is on the right

in this illustration.

Standard paper sizes that can be

used in this copier are shown be-

low.

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing The Roll Paper Size

Metric version

Roll Feeder

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

Loa d ing A Roll Of Pa p e r

When C is displayed, it is time to install a new roll of paper.

R CAUTION:

• Rolls of paper can be heavy, so you should be careful when load-

ing one.

• Be careful when replacing the roll paper or removing misfed pa-

per by following the operating instructions properly. Otherwise,

an injury may result from the paper cutter inside.

• Do not touch the anti-humidity switch from inside the machine. It

could be very hot.

Important

❖ When removing paper rolls, lift the roll holders on both sides of the paper roll

before removing it. Do not lift one side only. This could damage the machine.

ZEDH390E

A Pull out the Roll Feeder.

B Hold both sides of the empty paper roll and remove it from the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading A Roll Of Paper

C Raise the lever on the paper holder (A), and then pull out the roll holder

from the empty core (B).

D Set the paper holder (A) to the roll core, and then lower the lever (B).

Note

❖ Insert the paper roll as far as it will go.

E Hold both sides of paper roll in the paper roll and install it securely in the

paper holder.

Note

❖ The flap of the paper roll should be on the bottom. See below.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

❖ If applicable, adjust the roll paper position and lock the lever.

❖ You may hardly to adjust the roll paper position when you set 914mm (“36

). In this case, take out the paper holder, and then release the lock lever. Af-

ter you adjust it, put it back to the roll feeder.

❖ Do not force to remove the paper holder when you need to change the pa-

per size. For how to remove and set the paper holder, see⇒ P.52 “Changing

The Roll Paper Size”

F Rotate the paper roll slowly until the flap is almost fed into the rubber part

of the roller (A). While feeding the flap of the paper roll into the rubber

part of the roller, turn the paper knob clockwise (B).

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading A Roll Of Paper

Note

❖ Do not hold the paper knob from side. It may cause you touching a sticky

oil. For how to turn the knob without any harm, see the illustration below:

❖ Make sure that the paper is not loose. Insert it straight into the roller.

❖ Watch carefully to make sure that the flap of the paper is inserted between

feeder and the roller.

❖ For how to change the Roll 2, refer to the following illustration:

G Hold the paper (B ), and then slide the cutter (A).

Note

❖ Slide the cutter one way only, otherwise paper waste may pile up inside

the machine.

H Turn the knob anticlockwise about 1/4 to adjust the paper position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

I Close the Roll Feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading A New Roll Onto Paper Cutting Rail (Option)

Loa d ing A Ne w Roll Onto Pa p e r Cutting

Ra il (Op tion)

A Lift the rail.

B Remove the spool from its support.

C Remove one of the end caps and slide the old roll off the spool.

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintaining Your Copier

D Slide the new roll on the spool and put the cap over the end of the roll.

E Place the spool on the holder so that the paper rolls off the front. Push it all

the way in.

F Lower the rail.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Troub le shooting

If Som e thing Goe s Wrong

If you have problems with your copier, consult the following pages. If a service

indicator lights up, read the following section. If the original or copy is stuck in

the copier; ⇒ P.62; if the copier won't start, or if copies don't look right, ⇒ P.70.

If Indicator Lights Up

If one of the indicators shown appears on the operation panel, turn to the appro-

priate page and follow the instructions described there.

What appears

What it means

What to do

The original or copy paper is See the following section.

jammed somewhere.

The copier needs a technician. Call your service representa-

tive.

A cover ,unit, or the fusing

unit cover was left open.

Close it. Press firmly.

The paper roll is finished.

Put in a new roll of paper. ⇒

P.54.

The toner cartridge is empty, Replace the toner cartridge. ⇒

or almost empty. P.48.

Wait until the ready indicator Wait. If it stays on for an unu-

lights.

sually long time, call your

service representative.

The used toner bottle is full.

Empty the used toner bottle.

⇒ P.45.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If Ja m s Oc c ur

If the Original is Jammed at the Exit

Note

❖ If the paper or original gets stuck in the copier, remove both original and pa-

per.

A Lift the original table.

B Very gently pull the original out of the feed-out slot. Be careful not to tear

it.

C Close the original table. Press firmly on both sides until it clicks into place.

Download from Www.Somanuals.com. All Manuals Search And Download.

If Jams Occur

If Sheet Paper is Jammed in the Feed-in Slot

R CAUTION:

• The fusing unit can be very hot. Do not touch any parts under the

fusing cover. If necessary, wait until the fusing unit has cooled

down.

A Squeeze the locks on each side of the copier and lift the unit.

B Pull out the copy paper. Do not leave any scraps of paper in the copier.

C Close the unit. Press firmly on both sides until it clicks into place.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If Sheet Paper is Jammed at the Paper Exit

R CAUTION:

• The fusing unit can be very hot. Do not touch any parts under the

fusing cover. If necessary, wait until the fusing unit has cooled

down.

A Squeeze the locks on each side of the copier and lift the moddle unit be-

tween the original table and the bypass table.

B Open the fusing unit cover.

C Slowly pull the paper out. If there are scraps left inside, open the inner cov-

er, wait for the copier to cool, and remove the scraps.

Download from Www.Somanuals.com. All Manuals Search And Download.

If Jams Occur

D Close the unit and all covers. Press firmly on both sides until it clicks into

place.

If Roll Paper Jams

If roll paper jams anywhere in the machine, you still might need to check every-

where to remove the entire length of paper.

R CAUTION:

• Be careful when replacing the roll paper or removing misfed pa-

per by following the operating instructions properly. Otherwise,

an injury may result from the paper cutter inside.

• Do not touch the anti-humidity switch from inside the machine be-

cause it could be very hot.

A Open the Roll feeder.

B Slowly pull up the edge of the paper.

C Slide the cutter knob(A) to cut the edge of the roll paper, and then remove

the jammed paper(B)

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Note

❖ Slide the cutter one way only, otherwise paper waste may pile up inside

the machine.

D Rotate the paper roll in the direction of the arrow until you can see the edge

of the paper.

E Turn the knob anticlockwise about 1/4 to adjust the paper position.

F Slowly rotate the paper roll until the edge of the paper is fed into the rub-

ber part of the roller(A). While feeding the flap of the paper roll into the

rubber part of the roller, turn the paper knob clockwise(B).

Note

❖ Do not hold the paper knob from side. It may cause you touching a sticky

oil. For how to turn the knob without any harm, see the illustration below:

Download from Www.Somanuals.com. All Manuals Search And Download.

If Jams Occur

❖ Make sure that the paper is not loose. Insert it straight into the roller.

❖ Watch carefully to make sure that the flap of the paper is inserted between

feeder and the roller.

G Close the Roll Feeder.

If You Cannot See the Roll Paper Jam

If roll paper jams inside the roll feeder, you still might need to check everywhere

to remove the entire length of paper.

R CAUTION:

• The fusing unit can be very hot. Do not touch any parts under the

fusing cover. If necessary, wait until the fusing unit has cooled

down.

• Be careful when replacing the roll paper or removing misfed pa-

per by following the operating instructions properly. Otherwise,

an injury may result from the paper cutter inside.

• Do not touch the anti-humidity switch from inside the machine be-

cause it could be very hot.

A Open the Roll Feeder.

B Rotate the paper roll in the direction of the arrow until you can see the edge

of the paper.

C Cut the edge of the paper with the cutter or scissors.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

D Hold the paper (B ), and then slide the cutter (A).

Note

❖ Slide the cutter one way only, otherwise paper waste may pile up inside

the machine.

E Turn the knob anticlockwise about 1/4 to adjust the paper position.

F Slowly rotate the paper roll until the edge of the paper is fed into the rub-

ber part of the roller (A). While feeding the flap of the paper roll into the

rubber part of the roller, turn the paper knob clockwise(B).

Note

❖ Do not hold the paper knob from side. It may cause you touching a sticky

oil. For how to turn the knob without any harm, see the illustration below:

❖ Make sure that the paper is not loose. Insert it straight into the roller.

Download from Www.Somanuals.com. All Manuals Search And Download.

If Jams Occur

❖ Watch carefully to make sure that the flap of the paper is inserted between

feeder and the roller.

G Close the Roll Feeder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Othe rs

If a puzzling or recurring problem occurs, check the following before calling a

service representative. It's also a good idea to check the ⇒ P.73 “Do' s & Don' ts”

to make sure the paper and originals match what the copier can handle.

Absolutely nothing happens

• Is the main switch on?

• Is the power cord plugged in?

• Did a breaker or a fuse blow out?

Something happens, but Set Paper or RF Select never appear

• Check the indicators on the control panel. If any of them are lit, turn to ⇒ P.61.

Check that all covers and units are closed.

If Jams Occur Frequently

• Is your paper creased, damp, or otherwise damaged? ⇒ P.8.

• Are there visible bits of paper or other objects stuck in the machine? If there

are, remove them.

• Are you inserting the paper and original in straight? Always feed paper in

straight.

If Copies Look Wrong

• Are copies too dark or too light? Adjust the density (⇒ P.29).

• Is the background dirty no matter what kind of original you are copying?

Make sure the exposure glass and platen are clean (⇒ P.72).

• Is the image skewed? Make sure to insert the paper and the original straight

into the machine. If you have the Original and Copy Guides (option), use

them.

White Spots Appear

• On the copy: try setting your copy paper with the other side facing up.

• At the leading edge: try setting your copy paper sideways.

• At the trailing edge: try giving a rising curl to the trailing edge. The curl

should go up, not down.

Download from Www.Somanuals.com. All Manuals Search And Download.

Others

Creases

• Try setting your copy paper sideways.

• If long creases appear on copies, try setting your copy paper sideways, or try

changing the copy media setting.

• If creases appear on copies made to transparent film, try setting your film

sheets sideways.

Copies Come Out Dog Eared

• Try setting your copy paper with the other side facing up.

• Make sure your copy paper is undamaged.

Black streaks appear on copies

• Check that the exposure glass is clean.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Da ily Ma inte na nc e

Clean the Exposure Glass & the Platen Plate

you should clean the copy and original tables with a damp cloth, then wipe them

with a dry cloth.

Clean the exposure glass and the Original Drive Roller with a damp cloth, then

wipe it with a dry cloth.

Clean the platen plate with a damp cloth, then wipe it with a dry cloth.

Download from Www.Somanuals.com. All Manuals Search And Download.

Do's & Don'ts

R CAUTION:

• When you move the machine, unplug the power cord from the

wall outlet to avoid fire or electric shock.

• When the machine will not be used for a long time, unplug the

power cord.

• Do not touch areas on or around the fusing unit. These areas get hot.

• After copies are made continuously, the exposure glass may feel warm. This

is not a malfunction.

• The area around the ventilation hole may feel warm. This is caused by ex-

haust air and is not a malfunction.

• Do not turn off the main switch while copying. Before turning off the main

switch, make sure that copying is completed.

• The machine might fail to produce good copy images if there is condensation

inside caused by a temperature change.

• Do not open the covers of the machine while copying. If you do, misfeeds

might occur.

• Do not move the machine while copying.

• The supplier shall not be liable for any loss or damage resulting from a failure

of the machine, a loss of machine settings, or use of the machine.

• Do not place more than one sheet of paper at a time on the bypass table.

• Center your paper on the copy table using the size marks. Then slide the pa-

per straight into the copier until it stops.

• When copying to a long sheet of paper, lightly hold the sheet as the copier

pulls it in so that it goes in well.

• Do not make two sided copies.

• If you open the unit, make sure you close it within 5 minutes to keep light

from damaging the copy drum.

• When copying to sheets 35" ×45" (90 cm ×115 cm) or larger, make sure the pa-

per does not drag directly on the floor as the copier pulls it in. (You can spread

paper on the floor for this.)

• If your paper has an uneven or slanted edge, do not insert this edge in first.

• Do not make copies longer than 80 inches (2 m).

• Do not insert originals made of paper less the 52.3 g/ m²(13.9 lb or 0.07 mm

thick). For such originals, please use the optional Carrier Sheet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Whe re to Put Your Cop ie r

Your copier should be installed by a qualified technician. If you need to trans-

port your copier to a distant location, call your service center before the move.

You can of course move your copier around your office without calling the serv-

ice center. If you do, remember that the temperature, humidity, and cleanliness

of the area around the copier may affect its performance. Choose the new loca-

tion with care and follow the guidelines below.

Machine Environment

Your machine's location should be carefully chosen because environmental con-

ditions greatly affect its performance.

Optimal Environmental Conditions

R CAUTION:

• Keep the machine away from humidity and dust. A fire or an elec-

tric shock might occur.

• Do not place the machine on an unstable or tilted surface. If it top-

ples over, it could cause injury.

R CAUTION:

• If you use the machine in a confined space, make sure there is a

continuous air turnover.

• Temperature: 50° to 86°F (15° to 30°C)

• Humidity: 20 to 80% RH

• To avoid possible ozone build-up make sure to install this copier in a large,

well ventilated room ensuring an air turnover of at least 1000 ft³/ hour/ per-

son (30 m³). When you use this machine for a long time in a confined space

without good ventilation, you may notice an odd smell. To keep the work-

space comfortable, we recommend that you keep it well ventilated.

• Set your copier on a strong and level base. The copier must be level within a

quarter of an inch (5 mm) left to right and half an inch (10 mm) front to rear.

Environments to Avoid

• Locations exposed to direct sunlight or strong light (more than 1500 lux)

• Dusty areas

• Areas with corrosive gasses

• Altitudes of over 6500 feet (2000 m)

Download from Www.Somanuals.com. All Manuals Search And Download.

Where to Put Your Copier

• Areas prone to strong vibrations

• Locations directly exposed to cool air from an air conditioner or heat from a

nearby heater(Sudden temperature changes may lead to condensation within

the copier.)

• Locations near a diazo copy machine.

Power Connection

R WARNING:

• Only connect the machine to the power source described on

the inside front cover of this manual.

R WARNING:

• Avoid multi-wiring.

• Do not damage, break or make any modifications to the pow-

er cord. Do not place heavy objects on it, pull it hard or bend

it more than necessary. These actions could cause an elec-

tric shock or fire.

• Do not plug or unplug the power cord with your hands wet.

Otherwise, an electric shock might occur.

R WARNING:

• Make sure the wall outlet is near the machine and freely ac-

cessible so that in event of an emergency it can be un-

plugged easily.

R CAUTION:

• When you move the machine, unplug the power cord from the

wall outlet to avoid fire or electric shock.

• When the machine will not be used for a long time, unplug the

power cord.

R CAUTION:

• When you pull out the plug from the socket, grip the plug to avoid

damaging the cord and causing fire or electric shock.

• Connect the copier to a power source meeting the specifications on the inside

front cover of this manual.

• Do not set anything on the power cord.

• Voltage must not fluctuate more than 10%.

• Make sure the copier is grounded.

• Make sure the plug is firmly inserted into the power outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

• Make sure the power outlet is close to the copier and easily accessible at all

times.

Access To Machine

Place the copier near a power source and provide clearance as shown.

1. Rear: more than 60cm, 23.7”

2. Right: more than 60cm, 23.7”

3. Left: more than 60cm, 23.7”

4. Front: more than 100cm, 40.0”

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Sp e c ific a tions

Cop ie r

Configuration

Process

Desktop

Dry electrostatic transfer system

Scanning

Original moving over a fixed fiber optics array

Originals

Sheet

Original Reference Position

Original Size

Center

Maximum: 914mm (W) × 3,000mm (L) (36" ×

118.0")

Minimum: A4 K (210 (W) × 297mm (L)) (8.5"

× 11")

Copy Size

Maximum: 914mm (W) × 3,000mm (L) (36" ×

118.0")

Minimum: A4 K (210 (W) × 297mm (L)) (8.5"

× 11")

Warm-up Time

Within 3 minutes at a room temperature of

74°F (23°C)

First Copy

Within 21 seconds (A1 L , 23" × 35",)

Copying Speed

Auto Reset Time

3600mm (141.7") per minute

2 minutes (can also be turned off or set to 1,3,4

or 5 minutes)

Reproduction Ratio

Paper Feed

Fixed: 1 to 1

manual feed/ optional roll feeder

Cartridge system

Toner replenishment

Self-diagnostic codes

Power Source

LED indicators

North America: 120V, 60Hz, 12A

Europe: 220-240V, 50/ 60Hz, 7A

Power consumption

Noise emission

Maximum 1.4kW

Stand by: less than 57dB

Copy cycle: less than 75dB (copier only)

Measurements made following ISO7779

Dimension (W × D × H)

1,080mm × 570mm × 490mm (42.5" × 22.4" ×

19.3")

Weight

79kg (174lb)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Op tions

• Roll feeder

Number of loaded paper

rolls

1 roll (Type 780A)

2 roll (Type 780B)

Acceptable Roll Size

Width:210, 257, 297, 364, 420, Width: 210, 257, 297, 364, 420,

515, 594, 660, 728, 800, 841,

880, 914mm

515, 594, 660, 728, 800, 841,

880, 914mm

Roll length: less than 150mm Roll length: less than 150mm

Note

❖ Maximum: 914mm (36") ❖ Maximum: 914mm (36")

❖ Minimum: 210mm (8.5") ❖ Minimum: 210mm (8.5")

Roll Diameter

Within 170mm (6.7")

Roll Core

75.7mm – 77mm(2.98" - 3.03") 75.7mm – 77mm(2.98" - 3.03")

Dimension (W × D × H)

1,200mm × 720mm × 775mm 1,200mm × 720mm × 775mm

(48” × 28.3” × 30.5“)

Weight

78kg (172lb)

86kg(189lb)

• Side Guide Type 770

• Table Type 770

• Roll Cutting Rail Type 770

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

Absolutely nothing happens, 70

Access To Machine, 76

Adding Toner, 48

If Copies Look Wrong, 70

If Indicator Lights Up, 61

If Jams Occur, 62

Adjusting Copy Image Density, 29

Adjusting the Fusing Temperature

Manually, 28

Anti-humidity Heater, 9

A) Program key, 35

If Jams Occur Frequently, 70

If Roll Paper Jams, 65

If Sheet Paper is Jammed at the Paper Exit,

If Sheet Paper is Jammed in the Feed-in

Slot, 63

If Something Goes Wrong, 61

If the Original is Jammed at the Exit, 62

If You Cannot See the Roll Paper Jam, 67

Basic Copying (Copying to sheets), 11

Basics, 5

B) Changing The Default Setting, 36

Black Streaks Appear on Copies, 71

Loading A New Roll Onto Paper Cutting

Rail, 59

Loading A Roll Of Paper, 54

Changing The Roll Paper Size, 52

Changing The Used Toner Bottle, 45

Clean the Exposure Glass & the Platen

Plate, 72

Copier, 77

Copier Exterior, 1

Copies Come Out Dog Eared, 71

Copying, 11

Copying Onto Other Media, 27

Copying Onto Roll Paper (Option), 19

Copy Settings, 27

Machine Environment, 74

Maintaining Your Copier, 45

Making Several Copies of the Same

Original, 30

Non-recommended Originals, 7

Notes for Leading and Side Edge of the

Originals, 7

Creases, 71

Do's & Don'ts, 73

Operation Panel, 3

Options, 78

Others, 70

ENERGY STAR Program, iv

Environments to avoid, 74

Partial Copying, 32

Power Connection, 75

Preset Cutting, 22

Guide To Components, 1

Programming Setting You Often Use, 35

Handling Toner, 10

Recommended Originals, 6