OWNER’S OPERATING MANUAL
SP-42
SP-50
SP-60
Flat Panel Plasma Display Monitor
with
Download from Www.Somanuals.com. All Manuals Search And Download.
THREE YEAR LIMITED WARRANTY
For Plasma Displays
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces
“The World’s Finest Home Theater Products.” With proper installation, setup and care, you should enjoy many years of
unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your
other important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of three (3) years from the effective date of delivery to the end user (excluding the plasma
glass panel).
PARTS (not including plasma glass panel): Runco will provide new or rebuilt replacement parts for the parts that fail due to
defects in materials or workmanship for a period of three (3) years from the effective date of delivery to the end user. Such
replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.
PLASMA GLASS PANEL: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of one (1) year from the effective date of delivery to the end user. In addition, Runco will
provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of one (1)
year from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the
remaining portion (if any) of the original warranty period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
Image burn-in on plasma display panels is specifically excluded from coverage under this Limited Warranty. Image burn-in is
the result of misuse of the product and therefore cannot be repaired under the terms of this Limited Warranty.
Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for extended periods of
time) will not cause damage to your display under normal conditions. Many DVD players are also equipped with screen savers
for this reason.
TO AVOID IMAGE RETENTION (Burn-in): Please ensure that still images are left on your plasma display panel for no more
than a few minutes. Also ensure that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture
information is present on the left and right edges of the screen) are used as infrequently as possible. This will prevent
permanent image burns on your plasma display panel, which can be seen permanently under certain conditions once burn-in
has occurred.
The types of images to avoid include video games, still images and computer screens with stationary tool bars and icons. (This
is why computers are equipped with screen savers – to prevent still images from burning into the monitor’s phosphors after
being displayed continuously for an extended period of time).
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does
not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from
accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper
maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and
brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote
control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this
Limited Warranty.
CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED
DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS
SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. IT IS IMPERATIVE THAT INSTALLATION
AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED RUNCO DEALER TO PROTECT YOUR RIGHTS UNDER
THIS WARRANTY. THIS WILL ALSO ENSURE THAT YOU ENJOY THE FINE PERFORMANCE OF WHICH YOUR RUNCO
PRODUCT IS CAPABLE WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL.
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There
are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to
the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from
state to state.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as
evidence of the purchase date.
IMPORTANT -- WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we
should discover a safety problem or product update for which you must be notified.
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of
the product, during usual working hours, providing location of product is within normal operating distance from a Runco
Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for
repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest
Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s
responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco
Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will
return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping
costs will be the responsibility of the owner.
COPYRIGHT AND TRADEMARKS:
© Copyright 2006 Runco International. This document contains proprietary information protected by copyright, trademark and
other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the manufacturer.
Reflection, Enhanced GEN3, DHD, Vivix, Virtual Cinema, CineWide, AutoScope, O-Path, CinOptx, LiveLink, CSMS, SuperOnyx
and VirtualWide are trademarks of Runco International. All other trademarks and registered trademarks used in this document
are the property of their respective owners.
Runco International products are manufactured under one or more of the following patents: US. Patent 6755540 and Other
Patents Pending.
iv
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this
Limited Warranty, please call or write:
RUNCO INTERNATIONAL, INC.
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777
Fax: (510) 324-9300
Toll Free: (800) 23-RUNCO
RUNCO VIDEO-PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
_________________________________________________________
Model Purchased
________________________________________
Date
____________________________________________________________________________________________________________
Serial Number
____________________________________________________________________________________________________________
Runco Authorized Dealer Name
____________________________________________________________________________________________________________
Address
____________________________________________
__________________
State/Province
________________________
Postal Code
City
____________________________________________
Phone
_________________________________________________________
Fax
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Thank you for your purchase of this quality Runco product! It has been designed to provide you with the quality of video that is
expected in a home theater. This manual is your guide through the menus and operation. For the best performance, please
read it carefully and keep it handy for future reference.
WARNING
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to
the equipment as possible, and should be easily accessible.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN
BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
Installation Manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area
may cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Please read and follow the safety precautions listed below to ensure the equipment is free from damage, and to ensure that no
injury will occur as a result of improper use.
• Do not insert any object, especially metal or liquids, into the plasma display.
• Do not place any objects containing water or any other liquid on top of the plasma display.
• Do not place the units in direct sunlight, near heaters or in extremely dusty or humid locations.
• Do not install this system outdoors or otherwise exposed to the elements.
• Do not place heavy objects on top of the plasma display.
• If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Do not place objects on the
power cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way,
please contact your Runco Dealer for a replacement cord.
• Do not remove the cover of the plasma display for any reason. If any problems arise with the unit, please contact a Runco
Dealer or Runco International for service. Removing the covers will void the warranty.
vi
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Table of Contents
THREE YEAR LIMITED WARRANTY .............................................................................iii
Safety Precautions .........................................................................................................vi
1. Introduction ...............................................................................................................1
About This Manual .......................................................................................................1
If You Have Comments About This Manual.............................................................1
Parts List ...............................................................................................................4
2. Controls and Functions ............................................................................................5
CinemaWall at a Glance ...............................................................................................5
CinemaWall Remote Control ......................................................................................10
3. Installation ...............................................................................................................13
Notes on Batteries................................................................................................13
Notes on Remote Control Operation.....................................................................13
Quick Setup ...............................................................................................................15
Ventilation.............................................................................................................17
Other Considerations............................................................................................18
Connections to the CinemaWall .................................................................................19
RS-232 Controller Connection..............................................................................25
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation .................................................................................................................27
Selecting an Input Source ..........................................................................................28
Using the On-Screen Menus ......................................................................................32
Picture..................................................................................................................34
Using Picture-In-Picture (PIP) .....................................................................................47
Enlarging One Part of the Screen ...............................................................................49
5. Maintenance and Troubleshooting ........................................................................51
6. Serial Communications ..........................................................................................53
RS-232 Connection and Port Configuration ...............................................................53
7. Specifications ..........................................................................................................65
CinemaWall Specifications .........................................................................................65
Computer/Video Signal Compatibility .........................................................................70
viii
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1List of Figures
2-1. CinemaWall Controls and Indicators.............................................................................5
3-3. RGB/Component Video (INPUT 1) Connection...........................................................19
3-4. ANALOG RGB OUT (INPUT 1) Connection.................................................................20
3-11. Audio Output Connection.........................................................................................24
3-12. Connecting Speakers...............................................................................................24
4-4. Typical Gray Bar Pattern for Adjusting Contrast..........................................................35
4-9. Viewing an Enlarged Area of the Display.....................................................................49
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Notes:
x
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
This Owner’s Manual describes how to install, set up and operate the Runco CinemaWall
Flat-Panel Plasma Display Monitor (Models SP-42, SP-50 and SP-60).
1.1
About This Manual
Throughout this manual, all three models are referred to collectively as the “CinemaWall.”
Except where noted, the features and functions described in this manual are common to
all versions of this product.
Runco has prepared this manual to help home theater installers and end users get the
most out of the CinemaWall.
Target Audience
Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
may require updating from time to time. You can always find the latest version of this and
If You Have Comments
About This Manual...
Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:
Textual and Graphic
Conventions
• Remote control button identifiers are set in upper-case bold type; for example, “Press
EXIT to return to the previous menu.”
• Computer or control system input (commands you type or program into the control
system) and output (responses that appear on-screen) is shown in monospace
(fixed-width) type; for example: “To change the aspect ratio to Letterbox, send the
command 02 2A 2A 53 5A 4D 53 30 33 03.”
• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <spacebar>, <Ctrl>, <Esc>
and <Tab>.
• <Enter>indicates that you may press either the RETURN or ENTER key on your
keyboard if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:
To prevent image retention (burn-in) on your display, ALWAYS use
a screen saver and set it to the shortest possible time.
WARNING
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
Tip
NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.
Note
CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.
Caution
WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.
WARNING
DANGER!
DANGER appears when a given action can cause severe injury or
death.
Use the following table to locate the specific information you need in this manual.
1.2
Using This Manual
If you need...
Information about obtaining service
... Turn to page:
General information about the CinemaWall Flat-Panel Plasma Dis-
play Monitor
Installation instructions
First-time configuration instructions
Advanced configuration instructions
Troubleshooting tips
Specifications for the CinemaWall Flat-Panel Plasma Display
Monitor
2
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The CinemaWall Flat-Panel Plasma Display Monitor combines high-resolution quality and
affordability into one package. It has all of the features that one has come to expect from a
Runco product, including high-quality video processing, aspect ratio control and ease of
use. The advanced Runco processing inside the CinemaWall combined with its high
native resolution allows the most accurate scaling for all types of signals, including DVD
(progressive or interlaced), all currently-available HDTV formats and computers.
1.3
Description, Features
and Benefits
For video originally made in film, the CinemaWall has built-in 3:2 pulldown for the sharpest
and most artifact-free images possible. Like all Runco plasmas, it can be mounted on a
wall, ceiling or placed on a tabletop and is bright enough for use in any lighting situation:
its size is such that it can be the centerpiece of many home theaters.
The CinemaWall offers a resolution of either 1365 x 768 (Models SP-50 and SP-60) or
1024 x 768 (Model SP-42). Both models include Runco’s discrete aspect ratio control
with VirtualWide™ mode to fill a 16:9 screen with standard 4:3 images without loss of
picture quality. Also included are discrete source selection, multi-language support and an
RS-232 interface for whole-house or automated control system integration.
The CinemaWall Flat-Panel Plasma Display Monitor has been carefully engineered with
ISF™ calibration standards for superb video performance. At less than five inches deep, it
can be wall-mounted or used on a tabletop stand.
The CinemaWall offers these key features and benefits:
Key Features and Benefits
• Screen Size (diagonal): 42 inches (Model SP-42), 50 inches (Model SP-50) or 60 inches
(Model SP-60)
• 16:9 Native Resolution: 1024 x 768 (Model SP-42) or 1365 x 768 (Models SP-50 and
SP-60)
• Multiple Aspect Ratios with VirtualWide™ Mode
• Less than 5-1/4 inches deep
• Dual DVI Inputs with High-bandwidth Digital Content Protection (HDCP)
• HDTV Compatible
• Exceptional detail and artifact-free video enhancement
• Vivix™ video processing with 3:2 film detection circuitry
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Your CinemaWall is shipped with the following items. If any items are missing or damaged,
please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.
➤
• CinemaWall Flat-Panel Plasma Display Monitor
• AC Power Cord
• Remote Control Unit and two (2), AA-size batteries
• Cleaning Cloth
• Cable Ties (2)
• Ferrite Cores (2) (for AC power cord)
• Small Ferrite Cores (3) (for audio cables)
• Warranty information and registration card
• Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual (this document)
Optional Accessories:
• Wall Mount Kit
• Table Stand
4
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Controls and Functions
2.1
CinemaWall at a
Glance
Figure 2-1 shows the locations of the CinemaWall controls, indicators and connectors.
Controls and Indicators
(SP-42/SP-50)
Main unit
5
(SP-60)
5
2
1
3
4
Operation panel
on the underside
of the main unit
INFO
/ SET
INPUT ASPECT RATIO – VOL +
STANDBY/ON
MENU
6
7
8
9
10
11
Figure 2-1. CinemaWall Controls and Indicators
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. DISPLAY STAND
Optional accessory for tabletop installations.
2. REMOTE CONTROL SENSOR
Receives the signals from the remote control.
3. AMBIENT LIGHT SENSOR (SP-42 and SP-50 only)
This sensor measures the light level in the viewing area; it is active when the Energy
4. STANDBY/ON INDICATOR
- Lights green to indicate normal operation;
- Flashes green (once per second) when the AUTO OFF feature is active.
- Lights red to indicate that the CinemaWall is in standby mode;
- Flashes green or red (twice per second) to indicate an error condition.
5. HANDLES
ALWAYS use the handles when carrying the unit.
6. STANDBY/ON BUTTON (
)
Press to put the display into operation or standby mode.
7. MENU
Press this button to show or hide the On-Screen Display (OSD) controls.
8. INFO/SET
When the OSD controls are visible on-screen, press this button to select an OSD
sub-menu or confirm a changed setting.
When no OSD appears on-screen, press this button to display the currently-selected
input, aspect ratio and input signal characteristics (resolution, timing etc.).
9. INPUT/UP (
)
Press this button to switch inputs or move the cursor up in the current OSD menu.
10. ASPECT RATIO/DOWN (
)
Press this button to change the aspect ratio (screen size) or move the cursor down in
the current OSD menu.
11. LEFT (
) / VOL – and RIGHT (
) / VOL +
These decrease or increase the volume of sound from the speakers, or move the
cursor left or right in the OSD mode.
6
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SP-42, SP-50 and SP-60 respectively.
Connectors
14
15
16
17
RS-232
DVI VIDEO
COMPONENT
9
10
11
12
13
IN
OUT
OUTPUT INPUT1 INPUT2
AUDIO AUDIO AUDIO
INPUT1
INPUT2
ANALOG RGB OUT
(D-Sub)
ANALOG RGB IN
(D-Sub)
DIGITAL RGB
(DVI-D)
RS-232C
COMBINATION
1
2
3
4
5
6
7
8
Figure 2-2. SP-42 Connector Panel
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
16
17
RS-232
DVI VIDEO
COMPONENT
10
11
12
13
9
IN
OUT
OUTPUT INPUT1 INPUT2
AUDIO AUDIO AUDIO
INPUT1
INPUT2
ANALOG RGB OUT
(D-Sub)
ANALOG RGB IN
(D-Sub)
DIGITAL RGB
(DVI-D)
RS-232C
COMBINATION
14
15
1
2
3
4
5
6
7
8
Figure 2-3. SP-50 Connector Panel
16
17
RS-232
DVI VIDEO
COMPONENT
10
11
12
13
9
IN
OUT
OUTPUT INPUT1 INPUT2
AUDIO AUDIO AUDIO
INPUT1
INPUT2
ANALOG RGB OUT
(D-Sub)
ANALOG RGB IN
(D-Sub)
DIGITAL RGB
(DVI-D)
RS-232C
COMBINATION
14
3
4
5
6
7
1
15
2
8
Figure 2-4. SP-60 Connector Panel
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. COMBINATION IN/OUT
Used to control multiple CinemaWall monitors collectively. Use a 6-pin, mini-DIN cable
(all pins wired straight-through).
2. Not used.
3. AUDIO (OUTPUT) (3.5-mm stereo mini jack)
Used to output the audio of the selected source component connected to the plasma
display to an AV amplifier or similar component. The output level is fixed.
4. AUDIO (INPUT 1) (3.5-mm stereo mini jack)
Connect this jack to the audio output connector(s) of the device connected to
INPUT 1.
5. AUDIO (INPUT 2) (3.5-mm stereo mini jack)
Connect this jack to the audio output connector(s) of the device connected to
INPUT 2.
6. ANALOG RGB OUT (INPUT 1) (15-pin D-Sub)
If desired, connect this output to the RGB input of a second display device.
This output is not active when the CinemaWall is off or in standby
mode.
Note
7. ANALOG RGB IN (INPUT 1) (15-pin D-Sub)
For connecting components that have RGB or component output jacks such as a
personal computer or external DTV decoder (a break out cable is needed for
BNC-type connection).
8. DIGITAL RGB (INPUT 2) (DVI-D, HDCP-compliant)
VESA-standard digital video input from a personal computer, or digital video from a
DVD player or HD set-top box.
9. RS-232 (9-pin, female D-Sub)
Connect the RS-232 output from your computer or automation/control system to this
input.
10. DIGITAL RGB (INPUT 5) (DVI-D, HDCP-compliant)
This DVI input will process digital video 480p, 720p and 1080i signals (computer rates
are not recommended).
11. AUDIO (INPUT 5 / INPUT 4 / INPUT 3) (3.5-mm stereo mini jack)
Used for external audio input from video sources connected to Inputs 5, 4 and 3.
12. INPUT 4
Interlaced or progressive component input (480p to 1080i, 50 or 60 Hz; 480i not
recommended – use INPUT 3 instead).
13. INPUT 3 (S-Video or Composite Video Input)
For connecting a VCR, camcorder, laser disc player or DVD player. Use the push
button between the two connectors to select S-Video or Composite Video on Input 3
(only one can be active at a time).
14. EXTERNAL SPEAKER OUTPUT (RIGHT)
For connection of an external right speaker. Connect a speaker that has an
impedance of 6 ohms.
15. EXTERNAL SPEAKER OUTPUT (LEFT)
For connection of an external left speaker. Connect a speaker that has an impedance
of 6 ohms.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
16. AC POWER INPUT
Connect the CinemaWall to power here, using the included power cord.
17. MAIN POWER SWITCH
Connects or disconnects the CinemaWall from the AC power source.
Figure 2-5 shows the CinemaWall remote control. The paragraphs that follow describe its
functionality.
2.2
CinemaWall Remote
Control
10
11
1
2
ASPECT RGB
RATIO SETUP
POWER
INFO
RGB-HD
DVI-D
1
S / V
2
12
COMP
DVI VIDEO
3
4
5
INPUT SELECTION
13
14
MENU
MAGNIFY
3
4
SET
5
6
7
8
PIP FUNCTION
SPLIT SUB INPUT
SWAP
PIP SHIFT
15
16
17
MUTE
VOLUME
-
+
P-OFF
P-ON CLEAR
18
19
9
Figure 2-5. CinemaWall Remote Control
1. ASPECT RATIO
Press this button repeatedly to select a display aspect ratio.
2. INPUT SELECT
Press one of these buttons to select an input.
10
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MENU
Press this button to show or hide the OSD controls.
4. Directional Buttons (
/
/
/
)
Use these buttons to navigate the OSD menus and adjust various settings.
5. SET BUTTON
Press this button to adjust or enter various settings on the unit.
6. SUB INPUT
When using the Picture-in-Picture (PIP) feature, press this button repeatedly to select
a sub-input source.
7. SPLIT
Press this button to change the PIP mode (picture-in-picture, side-by-side or off).
8. MUTE
Press this button to mute the speakers connected to the CinemaWall speaker
outputs. Press it again to restore the sound.
9. P-OFF (pin hole)
Using a straightened paper clip or similar object, press this button to program a
discrete IR code for powering off the CinemaWall into a control/automation system.
10. RGB SETUP
When using INPUT 1 to display images from a computer, press this button to
automatically set the Position, Clock and Phase settings to their optimum values.
11. STANDBY/ON (
)
Press to put the display into operation or standby mode.
12. INFO
Displays currently-selected input, aspect ratio and signal timing information.
13. INSTALLER ADJUST (pin hole)
Used to access the INSTALLER ADJUST menus.
14. MAGNIFY
Press this button to select and enlarge one part of the screen image.
15. SWAP
When using the Picture-in-Picture (PIP) feature, press this button to replace the main
screen with the sub-screen or vice versa.
16. PIP SHIFT
Press this button to change the position of the smaller PIP sub-window (lower right,
upper right, lower left or upper left).
17. VOLUME + / -
Use these buttons to increase or decrease the volume of sound from the speakers.
18. CLEAR (pin hole)
Using a straightened paper clip or similar object, press this button to clear a screen
maintenance program (refer to Program Timer (SP-42) / Screen Maint.
19. P-ON (pin hole)
Using a straightened paper clip or similar object, press this button to program a
discrete IR code for powering on the CinemaWall into a control/automation system.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
12
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installation
To install batteries in the remote control:
3.1
While pressing down lightly, slide
in the direction of the arrow.
Remote Control
1. Remove the battery cover from the
back of the remote control.
2. Insert the batteries included with the
remote control. Ensure that the
Two AA (R6)
batteries
polarities correctly match the
markings inside the battery
compartment.
and
3. Replace the battery cover.
• When installing batteries, make sure that the battery polarities are correct.
• Do not mix an old battery with a new one or different types of batteries.
Notes on Batteries
• If you will not use the remote control for a long time, remove the batteries to avoid
damage from battery leakage.
The remote control can be used to control the CinemaWall within the ranges shown in
Notes on Remote Control
Operation
7 m
(23 feet)
30°
30°
Remote Sensor
Figure 3-1. Available Range of the Remote Control
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not drop the remote control or expose it to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. If that occurs, move the
plasma display away from the fluorescent lamp.
• Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the plasma display.
The signal from the remote control can be reflected by walls or
other surfaces.
Note
• If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.
• Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the plasma display and repeat the operation.
14
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1 gives a quick overview of the CinemaWall installation process. The sections
following this one provide detailed instructions.
3.2
Quick Setup
Installation should be performed by a qualified custom video
installation specialist.
Note
Table 3-1. Installation Overview
For Details, refer to
Step
Procedure
page...
1
2
3
4
5
6
Mount the CinemaWall on a wall or table stand
Connect signal sources to the CinemaWall
Connect external controller to RS-232 port (optional)
Apply power to the CinemaWall
Change the OSD language, if desired
If using the CinemaWall with a computer, adjust computer
display properties
7
Display calibration: adjust the following for each input;
save settings when finished:
• Aspect ratio
• Brightness
• Contrast
• Color level
• Tint
• Sharpness
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation of your CinemaWall will ensure the highest possible picture quality.
Whether you are installing the CinemaWall temporarily or permanently, you should take
the following into account to ensure that it performs optimally.
3.3
Installation
Considerations
High-Altitude Operation
Due to the design of all plasma glass panels made by every manufacturer, and the
interaction between ambient air pressure and the plasma gases contained inside of the
panel, reliable operation of your plasma display cannot be assured during operation at
certain high-altitude locations.
➤
Runco has found this plasma monitor to operate reliably at altitudes of up to 6000 MSL
(mean sea level). At elevations higher than this, each panel may react differently,
depending upon the altitude, air pressure, humidity and other meteorological factors.
For this reason, Runco International makes no warranties or claims as to the reliable
operation of the CinemaWall at altitudes greater than 6000 feet above sea level. If you are
planning to use this product at a location above 6000 feet, please contact Runco
technical support for further information.
Mounting the CinemaWall
on a Wall or Table Stand
To install the CinemaWall, you will need either an optional table stand or wall-mounting kit.
The CinemaWall cannot be installed on its own.
➤
If you do decide to wall-mount the CinemaWall, ensure that the wall-mount bracket is
installed according to the instructions included with it. The wall must be capable of
supporting a redundant weight factor three (3) times the weight of the display, or be
reinforced.
Runco recommends that this be done by a custom installation specialist.
Use only a Runco-approved wall-mount kit or table stand that is
specifically designed for your display.
Note
You can attach your optional mounts or stand to the CinemaWall in either of two ways:
• While it is upright.
16
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
• As it lies flat with the screen face
down. Place the protective sheet,
which was wrapped around the
plasma monitor when it was
packaged, between the screen and
your work surface to avoid
scratching or otherwise damaging
the screen surface.
In general, minimize or eliminate light sources directed at the display. Contrast ratio in your
images will be noticeably reduced if light directly strikes the display, such as when a shaft
of light from a window or floodlight falls on the image. Images may then appear washed
out and less vibrant.
Ambient Light
Ventilation
If you are mounting the CinemaWall in an enclosure, leave at least 2 inches (50 mm) of
heat to disperse, maintaining the proper operating temperature.
Wall
50mm (2")
50mm (2")
Wall
50mm (2")
Figure 3-2. Ventilation Requirements for Enclosure Mounting
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Considerations
Other considerations and tips that can help improve your installation, avoid damage and
prolong operating life:
➤
• Keep the ambient temperature constant and below 35°C (95°F). Keep the display away
from heating and/or air conditioning vents. Changes in temperature may cause drifts in
the display circuitry, which may affect performance.
• Keep the CinemaWall away from devices that radiate electromagnetic energy such as
motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers and elevators.
• Handle the unit carefully when installing it. When carrying it, use the built-in handles; DO
NOT touch or hold the screen face.
• Set the unit away from heat, excessive dust, and direct sunlight.
• Protect the inside of the unit from liquids and small metal objects. In case of accident,
unplug the power cord and have it serviced by an authorized Runco Service Center.
• Do not hit or scratch the panel surface as this causes flaws on the surface of the
screen.
• For correct installation and mounting it is strongly recommended to use a trained,
authorized dealer.
• To avoid sulfurization, it is strongly recommended not to place the unit in a dressing
room in a public bath or hot spring bath.
18
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proceed as follows to connect the CinemaWall to your video sources, external controller(s)
– if present – and AC power.
3.4
Connections to the
CinemaWall
When connecting your equipment:
• Turn off all equipment before making any connections.
• Use the correct signal cables for each source.
• Ensure that the cables are securely connected. Tighten the thumbscrews on
connectors that have them.
the sections that follow.
Video Connections
RGB/Component Video (INPUT 1) Connection: Connect your personal computer or
DTV decoder with an RGB or component output to the ANALOG RGB IN input on the
CinemaWall, as shown in Figure 3-3.
INPUT1
ANALOG RGB OUT
ANALOG RGB IN
(D-Sub)
(D-Sub)
Figure 3-3. RGB/Component Video (INPUT 1) Connection
1. The CinemaWall accepts “sync-on-green” and composite sync
Note
RGB signals on INPUT1, as well as separate sync (RGBHV)
signals. For more computer signal compatibility information, refer
2. Some Macintosh computers may require a Macintosh video
adapter. Contact your nearest authorized service center or dealer.
3. INPUT 1 supports the VESA Display Data Channel (DDC 1/2B)
standard. This standard provides “Plug and Play” capability; the
display and a VESA DDC-compatible computer communicate their
setting requirements, allowing for quick and easy setup.
In order for Plug and Play to work correctly, you must turn on the
CinemaWall before you turn on the connected computer.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ANALOG RGB OUT (INPUT 1) Connection: The CinemaWall has an RGB output for
looping the signal received at INPUT 1 out to a second RGB display device. Connect the
INPUT1
ANALOG RGB OUT
ANALOG RGB IN
(D-Sub)
(D-Sub)
To external monitor
Figure 3-4. ANALOG RGB OUT (INPUT 1) Connection
A video signal is not output when the CinemaWall is powered off or in
standby mode.
Note
DVI-D (INPUT 2) Connection: The CinemaWall has a DVI-D input for connecting a
personal computer, DVD player, DTV decoder or any other device with a DVI output.
only) cable.
INPUT2
DIGITAL RGB
(DVI-D)
Figure 3-5. DVI-D (INPUT 2) Connection
20
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the DVI inputs whenever possible. This ensures the highest
video quality because the signal is carried in the digital domain
throughout the entire signal path, from source component output
into the display.
Tip
1. For computer signal compatibility information, refer to
Note
2. INPUT 2 supports the VESA Display Data Channel (DDC 2B)
standard. This standard provides “Plug and Play” capability; the
display and a VESA DDC-compatible computer communicate their
setting requirements, allowing for quick and easy setup.
In order for Plug and Play to work correctly, you must turn on the
CinemaWall before you turn on the connected computer.
Composite/S-Video (INPUT 3) Connections: The CinemaWall has S-Video and
Composite video inputs for connecting a VCR, camcorder, laser disc player, DVD player
or other standard-definition (480i) source. Connect such devices to INPUT 3 as shown in
To switch between the Composite and S-Video input, press the SELECT button between
the two connectors.
You cannot switch from the Composite to the S-Video input (or vice
versa) using the remote control.
Note
Press to switch between
Composite and S-Video input
AV component
Figure 3-6. Composite or S-Video (INPUT 3) Connection
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Video (INPUT 4) Connection: If you have a DVD player or DTV decoder
For best results, use INPUT 4 for 480p and higher-resolution sources
only. (Use INPUT 3 for standard-definition (480i) sources).
Tip
COMPONENT
Figure 3-7. Component Video (INPUT 4) Connection
DVI-D Video (INPUT 5) Connection: The CinemaWall has a DVI-D input for connecting
a DVD player, DTV decoder or any other device with a DVI output (computer signals are
DVI-D (digital only) cable.
DVI VIDEO
COMPONENT
Figure 3-8. DVI-D (INPUT 5) Connection
22
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Ferrite Cores to the Audio Cables: Three (3), small ferrite cores are
provided with the CinemaWall. Before connecting your audio equipment, attach a ferrite
interference (RFI) emissions to a level that conforms to FCC regulations.
Audio Connections
Wind the audio cable around the ferrite core once, then fasten the catch. If you are using
ferrite cores as needed.
Audio Cable (not supplied)
Small Ferrite Core
Figure 3-9. Attaching the Small Ferrite Cores to Audio Cables
Audio Inputs: The CinemaWall has five (5), stereo audio inputs; each one corresponds to
a video input.
Connect the audio outputs from your source components to these inputs using a cable
with a stereo miniplug at the CinemaWall end and the appropriate connector(s) (stereo
INPUT 1 / INPUT 2
OUTPUT INPUT1 INPUT2
AUDIO AUDIO
AUDIO
INPUT 5 / INPUT 4 / INPUT 3
COMPONENT
Figure 3-10. Connecting Audio Inputs
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Output: The CinemaWall has a stereo audio output for connection to an external
A/V receiver or powered speakers. The audio signal corresponding to the selected video
input is output to both the speakers and this audio output.
The audio output level is fixed. (The volume and mute controls affect
only the speaker outputs.)
Note
Use a stereo miniplug to connect the CinemaWall stereo audio output to your external
OUTPUT INPUT1 INPUT2
AUDIO AUDIO AUDIO
Figure 3-11. Audio Output Connection
Speakers: The CinemaWall has an internal, 8W per channel stereo amplifier that can
drive a pair of stereo speakers. Connect the
(positive) and
(negative) speaker wires
Maintain the correct polarity. For more information, refer to the owner’s manual for
your speakers.
m
m
2
1
Twist exposed
wire strands
together.
Push tab to the open
position, and insert the
wire. Then, close tab
firmly to secure the wire
in place.
Figure 3-12. Connecting Speakers
24
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Use a 9-pin, straight-through RS-232 cable to connect a PC or home theater
control/automation system (if present) to the RS-232 port (located next to INPUT 5) on the
RS-232 Controller
Connection
XMT DATA
RCV DATA
SIG GND
RCV DATA
XMT DATA
SIG GND
3
2
5
3
2
5
CinemaWall
To/From
PC or
Control
System
RS-232
DVI VIDEO
NO CONNECTION
1, 4, 6, 7, 8, 9
1, 4, 6, 7, 8, 9
DB-9 Female
DB-9 Male
Figure 3-13. RS-232 Control System Connection
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
26
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation
1. Turn on your source components.
4.1
Turning on the Power
2. Attach the two included ferrite cores to each end of the AC power cable as shown in
Figure 4-1. Doing so will reduce radio frequency interference (RFI) emissions to a level
that conforms to FCC regulations. Use the supplied cable ties to secure the cores in
place.
Ferrite core
Cable tie
To power outlet
To AC IN
AC power cord
As close as possible
Figure 4-1. Attaching the Ferrite Cores to the Power Cable
3. Plug the female end of the power cord into
the AC receptacle on the rear of the
CinemaWall (AC 100V ~ 240V). Connect the
other end to your AC power source.
4. Set the main power switch at the rear of the
position. Its power indicator lights red.
5. Press the POWER button on the underside
indicator lights solid green.
6. After a brief warm-up period (approximately 10 seconds), the CinemaWall will display
an image.
The CinemaWall OSD language is initially set to English, but can also display the menus in
German (Deutsch), French (Français), Spanish (Español) or Italian (Italiano). To change the
OSD language:
4.2
Changing the OSD
Language
1. Press MENU.
2. Press
repeatedly to select Option from the Main Menu.
3. Press SET to select Language.
4. Press the right- or left-arrow button (
or
) to highlight the desired language and
press SET. The change takes effect immediately.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To select an input source, press a numbered button
on the remote control corresponding to that input.
4.3
RGB-HD
DVI-D
INFO
Selecting an Input
Source
1
S / V
2
COMP
DVI VIDEO
3
4
5
INPUT SELECTION
Press INFO on the remote control to have the
CinemaWall display the currently-selected input, signal
timing information (frequency and polarity) and aspect
ratio. This information stays on-screen for about five
seconds.
4.4
INPUT1
Viewing Input Signal
Information
FH
FV
:
:
31.5kHz
60.0Hz
640X480
POL.H NEGA
POL.V POSI
:
:
PIX BY PIX
To maximize image quality when using the CinemaWall with a personal computer, you
may need to adjust the display properties of your computer’s video card. To do this on a
Microsoft® Windows®-based PC:
4.5
Setting the Computer
Display Properties
1. Choose Settings from the Windows Start
Menu and click on “Control Panel.”
2. Double click on the Display icon.
3. Click the Settings tab on the display dialog
box.
4. Adjust the resolution to 1024x768 pixels.
28
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click the Advanced button and click the
Monitor tab on the dialog box. Set the
vertical frequency to 60Hz and click OK.
1. The native resolution of the SP-42 is 1024 x 768; the native
Note
resolution of the SP-50 and SP-60 is 1365 x 768. Other
horizontal or vertical resolutions may be scaled upward or
downward to fit the display.
2. With most computers, you can get the best picture at
1024 x 768 @ 60Hz.
To prevent image retention (burn-in) on your display, ALWAYS use
a screen saver and set it to the shortest possible time.
WARNING
RGB Setup (Input 1 only): After adjusting the computer’s display properties, press the
RGB SETUP button on the remote control to have the CinemaWall automatically adjust
the size, position, and quality of the displayed image.
DVI Setup (Input 2 only): After adjusting the computer’s display properties, configure
To change the aspect ratio (size and shape) of the projected image, press the ASPECT
RATIO button repeatedly on the remote control. Select the appropriate aspect ratio for
4.6
Changing the Aspect
Ratio
1. Not all aspect ratios are available on some inputs. For example,
Standard 4:3 is not available on Input 5.
Note
2. The aspect ratio selection is saved independently for each input.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings
Aspect Ratio
Description
Select 16:9 (Anamorphic) to view 16:9
16:9
(Anamorphic)
DVDs and HDTV programs in their native
aspect ratio.
16:9 Image on
16:9 Screen (Display)
4:3 images are stretched horizontally to
fit a 16:9 screen.
4:3 Image, stretched to fill
16:9 Screen (Display)
4:3 (Standard)
Standard 4:3 scales the input signal to fit
in the center of the 16:9 screen. 4:3 is
the aspect ratio used by computer
monitors, standard television
programming and most VHS video
cassettes.
4:3 Image on
16:9 Screen (Display)
Letterbox
Letterbox mode scales (zooms in on) a
4:3 image linearly (by the same amount
on all sides) to fill a 16:9 display.
Letterbox is best suited for viewing
LaserDisc movies or non-anamorphic
DVDs on a 16:9 screen.
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
VirtualWide
VirtualWide scales a 4:3 image
NON-linearly (more on the sides than in
the center) to fit a 16:9 screen.
4:3 Image on
16:9 Screen (Display)
4:3 Image on
16:9 Screen
with VirtualWide
30
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Aspect Ratio
Description
Virtual Cinema
A 2.35:1 image is stretched
anamorphically in both directions to fill a
16:9 display area.
2.35:1 Image on
16:9 Screen
The 2.35:1 image is cropped on all sides.
2.35:1 Image on
16:9 Screen with
Virtual Cinema
14:9
14:9 scales the input signal to fit in the
center of the 16:9 screen.
Active Image
Area (14:9)
PIX BY PIX
Select PIX BY PIX to display a computer
screen image in the center of the display
with no re-sizing. Resolutions lower than
1024x768 (SP-42) or 1365x768
(SP-50/SP-60) will result in a black
border around the image; with higher
resolutions, the image will be cropped.
800x600
Image within
1024x768 Display
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the on-screen menus:
4.7
Using the On-Screen
Menus
2-1) to display the Main Menu. Or, using a straightened paper clip or similar object,
press the Installer Adjust menu button located below the Input 4 button on the remote
The Installer Adjust menu is intended for use by authorized,
trained service personnel only.
Note
2. To select a sub-menu, use the right- or left-arrow buttons (
,
) to highlight it.
3. Use the up- or down-arrow buttons (
4. Do one of the following:
,
) to select the setting you want to change.
Press SET repeatedly until the desired value appears;
– OR –
Press SET to display an on-screen slidebar or sub-menu. Press the right- or left-arrow
button (
,
) to change that setting. (If you do not do this within five seconds, the
slidebar disappears.) Press SET to confirm the setting.
5. If the current menu has a “RETURN” command, highlight it and press SET to return to
the previous menu. Or, press MENU to exit the OSD menu system.
The CinemaWall OSD menus are arranged hierarchically, as shown in Figure 4-2.
Depending on the selected input source and signal characteristics, some menu options
may not be available.
32
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contrast
English, Français,
Español, Deutsch
or Italiano
(Installer Adj.:
0 ... +255)
(Note 1)
Language
Brightness (Note 2) -30 ... 0 ... +30
Color
Auto 1, Auto 2,
Mute, Auto,
Average, Level 1,
Level 2 or Level 3
H. Sharpen
0, +1, +2 ... +15
V. Sharpen
(PC signals only)
Energy Mode
(Installer Adj.:
0 ... +60)
Tint
-30 ... 0 ... +30
-7, ... 0 ... +7
DST: On / Off
Day, Hour, Minute
Present Time
(Installer Adj.:
0 ... +15)
Sharpness
Time/Date
Program Timer
Return
On / Off
R. Gain
G. Gain
Off, Type 1, Type 2 or
Type 3
Orbiter
B. Gain
PDP Mgmt.
0 ... +255
Yes / No
Soften
Off, 1, 2, 3 or 4
R. Offset
G. Offset
B. Offset
White Bal. Reset
Return
White Balance
Picture
(Note 1)
Auto Setup Mode
Auto Function
On / Off
Off / Input 1 /
Input 4
MON, TUE ... SUN
(once only at the
selected day/time)
or
Red
Yellow
Date
*MON, *TUE ... *SUN
(weekly)
or “*” (daily)
Green
0 ... +60
Yes / No
Program Timer
(SP-42) /
Screen Maint.
Cyan
Color Chart
Blue
On
Off
00:00 ... 23:59
Magenta
C. Chart Reset
Return
(SP-50/SP-60)
Input 1 ... Input 5 or
“-” (last)
Input
Gamma
1.8, 1.9, 2.0 ... 2.4
Yes / No
H. Shift
White, Inverse, Orbiter
or “-” (last)
Pattern
Factory
Off, Inverse, White,
Red, Green, Blue or
Yellow
-64 ... +63
(Installer Adj.:
+64 ... +191)
Test Pattern
Sidebar Adjust
Baud Rate
Image Position
V. Shift
Option
R. Adjust
Frequency Adjust
Phase Adjust
-128 ... +127
-16 ... +15
(PC signals only;
Auto Setup Mode
must be OFF)
Screen
(Note 1)
G. Adjust
0 ... +255
B. Adjust
H. Size
Auto Side Mask
Default
Off / On
0 ... +64
V. Size
Image Reset
Yes / No
1200, 2400, 4800,
9600, 19200 or
38400
Low, Mid-Low,
Middle, Mid-High or
High
Color Temp.
ID Number
Fan Speed
01h - FFh or ALL
Auto or Max
Display
Auto Off
On / Off
Video NR
MPEG Filter
Chroma EE
Film Mode
Off, Low, Middle or
High
On / Off
OSD
Size
Small or Large
Front L.E.D.
ISF Settings
On / Off
On / Off
Normal or ISF ccc
Underscan
RGB, Comp. 1 or
Comp. 2
Color Space
On / Off
Set-Up
Normal, Pure,
Monotone or
High-Cnt.
Plug / Play
Black Level
Video / PC
Low / High
DVI Setup
(Input 2 only)
Display Profile
Runco Pro
Auto,
480p ... 1080i or
640x480 ...
1376x768 (choices
vary per input)
Motion, Still or
Non-Std.
Signal Type
Normal or Scaler
Input
Signal
FRC
Input 1, 2, 3, 4 or 5 or
Last
Power On Mode
Brt. Enhance
Sub Volume
On / Off
Volume
Off
0, 1, 2 ... 42 or Last
0 ... +20
Seamless Switch
Select 1 / Select 2:
Input 1 - 5
On
Flip H, Flip V,
Flip HV or Off
Picture Orient.
Function Reset
Yes / No
Notes:
1. Menu items in italics appear only when the CinemaWall is in Installer Adjust mode. Picture and Screen settings made in Installer Adjust
mode define the “zero point” for normal, “User-mode” adjustments. For example, setting Contrast in Installer Adjust mode defines the
white level that results when Contrast is set to 0 in “User” mode. Menu items in bold type appear only on the CinemaWall
Models SP-50 and SP-60.
2. When adjusting the Brightness (black level) for RGB and Component HD (480p/720p/1080i) signals, use the “User mode” Brightness
control. For 480i and digital video sources, either Brightness control (“User” mode or Installer Adjust mode) can be used.
Figure 4-2. CinemaWall OSD Menu Structure
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
Picture
The Main Menu is the starting point for accessing all CinemaWall functions. Some menu
options are available only in “Installer Adjust” mode.
➤
➤
Use the controls in the Picture menu to calibrate your CinemaWall for optimum picture
quality.
CINEMAWALL
INPUT 3
OPTION
The CinemaWall has been designed to incorporate setup and calibration standards
established by the Imaging Science Foundation (ISF). The ISF has developed carefully
crafted, industry-recognized standards for optimal video performance and has
implemented a training program for technicians and installers to use these standards to
obtain optimal picture quality from Runco video display devices. Accordingly, Runco
recommends that setup and calibration be performed by an ISF-certified installation
technician.
PICTURE
SCREEN
SET-UP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
:
:
:
:
0
0
0
0
0
:
FACTORY
SET
ENTER
MENU
EXIT
INSTALLER ADJUST
INPUT 3
OPTION
All signal types require separate processing. Therefore, you need to calibrate each input
separately.
PICTURE
SCREEN
SET-UP
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
WHITE BALANCE
COLOR CHART
GAMMA
:
:
:
:
:
+128
+128
+64
+30
+8
Although it may be possible to obtain satisfactory picture quality using the naked eye and
regular program material, Runco recommends using the following calibration tools for best
results:
:
2.2
FACTORY
• External test pattern source – Ovation Multimedia, Video Essentials or AVIA test DVD
(or equivalent).
SET
ENTER
MENU
EXIT
• A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the input that you are calibrating and proceed as
follows. Perform the adjustments in the order listed here.
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an
pattern.
Below Black
Above Black
Figure 4-3. Typical PLUGE Pattern for Adjusting Brightness
34
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUGE patterns vary but generally consist of some combination of black, white and gray
areas against a black background. The example above includes two vertical bars and four
shaded boxes.
Select Brightness from the Picture menu. Using the left- and right-arrow (
adjust the brightness so that:
) buttons,
• The darkest black bars disappear into the background.
• The dark gray areas are barely visible.
• The lighter gray areas are clearly visible.
• The white areas are a comfortable level of true white.
• The image contains only black, gray and white (no color).
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the
Figure 4-4. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast from the Picture menu. Using the left- and right-arrow (
) buttons,
adjust the contrast to a point just below which the white rectangle starts to increase in
size.
Brightness and contrast controls are interactive. A change to one
may require a subtle change to the other in order to achieve the
optimum setting.
Note
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Saturation: On your external test pattern source, select a color bar pattern like the
Figure 4-5. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
Select Color from the Picture menu. While looking at the color bar pattern through a blue
filter, adjust the color saturation level until the outermost (gray and blue) color bars appear
to be a single shade of blue:
H. Sharpen/V. Sharpen (computer signals only): Select H. Sharpen or V. Sharpen
from the Picture menu to enhance the level of detail (in the horizontal or vertical direction
respectively) in a computer screen image.
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image.
When tint is decreased, the image appears redder; when it is increased the image
appears greener. To set the tint, select Tint from the Picture menu. While looking at the
color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color
bars (on either side of the green bar) appear to be a single shade of blue.
36
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Like the brightness and contrast controls, the color and tint controls
are interactive. A change to one may require a subtle change to the
other in order to achieve the optimum setting.
Note
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust
sharpness, select Sharpness from the Picture menu and press SET. On your external test
looking for white edges around the transitions from black to gray and different sized lines
in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate
them.
Figure 4-6. Typical Test Pattern for Adjusting Sharpness
White Balance (Installer Adjust mode): Select White Balance from the Installer
Adjust/Picture menu to remove any trace of color from the white areas of the image.
WHITE BALANCE
• Gain: Use the Gain controls to correct color imbalances in the bright areas of the
image. A good way to do this is to use a test pattern consisting mostly of solid white
areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red,
green or blue, decrease the Gain for that color.
R. GAIN
G. GAIN
B. GAIN
R. OFFSET
G. OFFSET
B. OFFSET
:
:
:
:
:
:
+128
+128
+128
+128
+128
+128
• Offset: Use the Offset controls in the White Balance sub-menu to correct color
imbalances in the dark areas of the image. A good way to do this is to use a test
pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the
gray areas contain traces of red, green or blue, decrease the Offset for that color.
WHITE BAL. RESET
RETURN
SET
ENTER
MENU
EXIT
To reset the white balance settings to the factory default values, select White Bal. Reset.
Then, press
to highlight YES and press SET.
Select Return to exit the White Balance menu.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Chart (Installer Adjust mode): Select Color Chart from the Picture menu to
adjust the color density for each of the six primary colors: red, yellow, green, cyan, blue
and magenta. Changing these settings for a primary color alters the hue of that color and
affects the gamut (range) of possible colors. For example, changing the value for red
moves the color closer to either yellow or magenta, which in turn affects all displayed
colors having a red component.
COLOR CHART
RED
:
:
:
:
:
:
+30
+30
+30
+30
+30
+30
YELLOW
GREEN
CYAN
BLUE
MAGENTA
To reset the color gamut settings to the factory default values, select C. Chart Reset.
C. CHART RESET
RETURN
Then, press
to highlight YES and press SET.
SET
ENTER
MENU
EXIT
Select Return to exit the Color Chart menu.
Gamma (Installer Adjust mode): The Gamma control determines how gray shades are
displayed between minimum input (black) and maximum input (white) for all signals. A
good gamma setting helps to optimize blacks and whites while ensuring smooth
transitions for the “in-between” values utilized in other grays.
Unlike brightness and contrast controls, Gamma allows you to lighten or darken the
overall tone of your images without changing the extremes. All images will be more vibrant
while still showing good detail in dark areas.
The default Gamma setting of 2.2 is appropriate for most typical home theater
environments.
Factory: To reset all picture quality settings for the current input to the default,
installer-adjusted values (or factory defaults, if in Installer Adjust mode), select Factory
from the Picture menu. Then, press
to highlight YES and press SET.
Screen
Image Position: Use the up- or down-arrow buttons (
Position. Then, press SET and use the left- and right-arrow buttons (
image horizontally; use the up- or down-arrow buttons (
vertically.
,
) to highlight Image
) to shift the
) to shift the image
➤
,
CINEMAWALL
INPUT 1
OPTION
,
PICTURE
SCREEN
SET-UP
IMAGE POSITION
FREQ. ADJ.
PHASE ADJ.
:
:
:
0/
0
0
0
V Shift (Installer Adjust mode): Use the up- or down-arrow buttons (
V Shift. Then, press SET and use the right-arrow button ( ) to shift the image up; use
the left-arrow button ( ) to shift the image down.
,
) to highlight
IMAGE RESET
H Shift (Installer Adjust mode): Use the up- or down-arrow buttons (
,
) to
highlight H Shift. Then, press SET and use the right-arrow button (
) to shift the image
SET
ENTER
MENU
EXIT
to the right; use the left-arrow button (
) to shift the image to the left.
INSTALLER ADJUST
INPUT 1
OPTION
Frequency Adjust (Input 1 only): Use the up- or down-arrow buttons (
highlight Freq. Adj. Then, press SET. The Frequency Adjust control adjusts the
CinemaWall’s internal clock frequency in small increments to match that of the incoming
signal. Use it to reduce or eliminate letter breakup, flickering or other “noise” in a computer
screen image.
,
) to
PICTURE
SCREEN
SET-UP
H SHIFT
V SHIFT
FREQ. ADJ.
PHASE ADJ.
H SIZE
:
:
:
:
:
:
+128
+128
0
0
0
0
V SIZE
IMAGE RESET
Phase Adjust (Input 1 only): Use the up- or down-arrow buttons (
,
) to highlight
Phase Adj. Then, press SET. Use the Phase Adjust control to correct color misalignment
SET
ENTER
MENU
EXIT
or flickering text in a computer screen image.
Frequency Adjust and Phase Adjust are adjustable only when Auto
Setup Mode (in the Option menu, described later in this section) is
set to OFF.
Note
38
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
V Size (Installer Adjust mode): Use the up- or down-arrow buttons (
V Size. Then, press SET and use the right-arrow button ( ) to increase the height; use
the left-arrow button ( ) to decrease it.
,
) to highlight
H Size (Installer Adjust mode): Use the up- or down-arrow buttons (
H Size. Then, press SET and use the right-arrow button ( ) to increase the width; use
the left-arrow button ( ) to decrease it.
,
) to highlight
Image Reset: To reset all screen settings for the current input to the default, Installer
Adjust mode values, select Image Reset from the Screen menu. Then, press
to
highlight YES and press SET.
Color Temperature: To adjust the color temperature, select Color Temperature from
the Set-Up menu. (Color temperature defines the “color of gray.”) Use the left- and/or
right-arrow buttons to select LOW, MID-LOW, MIDDLE, MID-HIGH or HIGH. The default
setting, MIDDLE, is appropriate for most situations. Higher settings produce a “bluer”
picture; lower ones cause the image to appear more red.
Set-Up
CINEMAWALL
INPUT 2
OPTION
PICTURE
SCREEN
SET-UP
COLOR TEMP.
AUTO OFF
VIDEO NR
MPEG FILTER
CHROMA EE
FILM MODE
COLOR SPACE
DVI SET UP
SIGNAL
:
MIDDLE
:
:
:
:
:
:
OFF
MIDDLE
LOW
ON
Auto Off: When using the CinemaWall with a computer, set Auto Off to ON to have the
CinemaWall go into standby mode when no source signal is present on the current input.
(A warning message appears on-screen for approximately eight seconds before this
occurs.) To return to normal operating mode from the Auto Off standby mode, select the
input with the remote control or operate your computer.
OFF
RGB
:
720p
SET
SET
MENU
EXIT
When Auto Off is disabled (OFF), the CinemaWall remains in normal operating mode,
regardless of the presence or absence of an input sync signal.
INSTALLER ADJUST
INPUT 1
OPTION
PICTURE
SCREEN
SET-UP
BRT. ENHANCE
SUB VOLUME
:
:
OFF
+20
1. If the computer is turned off or not properly connected to the
CinemaWall, the system is set to the off state.
Note
2. For instructions on using the computer's power management
features, refer to the instructions for your computer.
SET
SET
MENU
EXIT
The STANDBY/ON indicator at the front of the CinemaWall indicates the status of the
Table 4-2. Power Management Indications
Power
management
mode
STANDBY/
ON
Indicator
Power
management
operating status
Turning the
picture back on
Description
ON
Solid
green
Not activated.
Activated.
Horizontal and ver- Picture already on.
tical synchronizing
signals are present
from the com-
puter.
OFF
Flashing
green
Horizontal and/or
Press a key on the
vertical synchroniz- keyboard or move
ing signals are not
present from the
computer.
the mouse. The
picture reappears.
Video NR: To apply Digital Noise Reduction (DNR) to the input signal, select Video NR
from the Set-Up menu. Noise reduction is useful for improving the signal-to-noise ratio of
video signals.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the left- or right-arrow buttons to select the desired amount of noise reduction,
keeping in mind that higher settings (which reduce high frequencies) may also “soften” the
image.
MPEG Filter: Use the MPEG Filter to reduce or eliminate so-called “mosquito noise” in
MPEG-compressed video signals (digital broadcasts or DVDs). Set it to LOW, MIDDLE or
HIGH, as needed to minimize distortion around the edges of moving objects, moving
artifacts around edges and/or blotchy noise patterns superimposed over the objects.
Chroma EE: Use the Chroma EE control to correct chroma delay in a Composite,
S-Video or Component video source. Chroma delay in an image causes color shifts to
occur to the left of the vertical edge transitions, producing artificial shadows or a “halo”
effect. If necessary, set Chroma EE to ON to eliminate them.
Film Mode: When you enable Film Mode, the CinemaWall automatically detects and
optimizes the display of interlaced video signals that originated from film. To disable Film
Mode, set it to OFF.
Film Mode can only be used on input signals with a 60-Hz refresh
rate.
Note
Color Space: To ensure proper color reproduction, select Color Space from the Set-Up
menu and set it as follows:
• Select RGB for RGB input signals from a computer or video deck.
• Select COMP. 1 for component input signals less than 720p, such as from a DVD
player.
• Select COMP. 2 for higher-resolution component input signals (720p or above, such
as from an HD tuner).
DVI Setup (Input 2 only): Select DVI Setup from the Set-Up menu to configure Input 2
for “plug-and-play” operation with a computer, and select the appropriate black level.
DVI SETUP
• Plug/Play: If the Input 2 source is a computer, set this to PC. Otherwise, set it to
PLUG/PLAY
BLACK LEVEL
:
:
VIDEO
LOW
Video.
• Black Level: This control compensates for incoming elevated black levels present in
certain video signals. Generally, the CinemaWall automatically determines the best
setting according to the incoming video signal type. For some types of video, you may
want to override the setting. Set it to LOW if blacks appear elevated (dark gray). If
blacks appear “crushed” (too dark), set it to HIGH.
SET
ENTER
MENU
EXIT
Signal: The CinemaWall automatically identifies PC signals and video signals according to
the frequency of the input signal, and identifies the resolution of a PC signal.
In most cases, setting Signal to Auto works well. However, if the displayed image is
unstable or distorted, select Signal from the Set-Up menu and select a specific signal
format. The available choices vary for each input.
Brt. Enhance (Installer Adjust mode): To improve and enhance the brightness of the
center of the screen, select Brt. Enhance from the Set-Up menu and set it to ON. This
reduces the brightness of the outer areas of the display by about 3 to 5%, relative to the
center. For uniform brightness over the entire screen area, set Brt. Enhance to OFF.
40
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Sub Volume (Installer Adjust mode): Select Sub Volume from the Set-Up menu to
adjust the audio input level for the current source. Do this for all sources, as needed to
prevent sudden, drastic changes in sound volume when switching inputs.
For example, if a DVD player is connected to Input 4, a computer is connected to Input 1
and the audio output of the DVD player is fixed at a much higher level than that of the
computer, reduce the Sub Volume for Input 4.
The Sub Volume control affects the current input only; the front-panel and remote volume
1
2
AUDIO INPUT
(INPUT1)
INPUT1
SUB VOLUME
INPUT2
SUB VOLUME
AUDIO INPUT
(INPUT2)
INPUT
SELECTOR
POWER
AMPLIFIER
INPUT3
SUB VOLUME
3
4
AUDIO INPUT
(INPUT3)
VOLUME
INPUT4
SUB VOLUME
AUDIO INPUT
(INPUT4)
INPUT5
SUB VOLUME
5
AUDIO INPUT
(INPUT5)
Figure 4-7. Audio System Functional Block Diagram
Option
consumption and panel deterioration by limiting brightness of the screen. You can choose
to limit brightness according to the input signal or in response to the ambient light level.
CINEMAWALL
INPUT 3
OPTION
PICTURE
SCREEN
SET-UP
LANGUAGE
ENERGY MODE
TIME / DATE
PDP MGMT.
AUTO SETUP MODE
AUTO FUNCTION
:
:
ENGLISH
AUTO
• Select AVERAGE to limit brightness in accordance with the input signal to produce a
bright, easily viewed image.
:
:
OFF
OFF
• Select LEVEL 1 to limit brightness in accordance with the input signal. Power
consumption is less than that used in AVERAGE mode.
MENU
SET
ENTER
EXIT
• Select LEVEL 2 to limit brightness in accordance with the input signal. Power
consumption is less than that used in LEVEL1 mode.
• Select LEVEL 3 to set the brightness at fixed level, regardless of input signal level
(useful for preventing screen aging due to image burn).
• Select AUTO (Model SP-42), AUTO1 or AUTO2 (Model SP-50/SP-60) to have the
CinemaWall adjust the brightness automatically in response to ambient lighting
conditions, to optimize picture quality.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
clock (time of day and day of the week) and turn the screen maintenance feature on or off.
Then, use the right- or left-arrow buttons (
,
) to set the time. Press SET again
when you are finished.
maintenance feature, which lets you replace the normal source signal with a white field,
an inverse image or an “orbiting” image. This occurs according to the schedule you
Installer Adjust mode (refer to Program Timer (SP-42) / Screen Maint.
Select Return to exit the Time/Date menu.
prevention settings on the CinemaWall.
• OFF: Orbiter mode does not function.
• TYPE 1: The image size is reduced so the entire image remains in the display area
while orbiting.
• TYPE 2: The image is enlarged so there are no black bands in the display area while
orbiting.
• TYPE 3: The image size is unchanged.
1. When TYPE 1 or TYPE 2 is selected, the image movement is
continuous; TYPE 3 causes the image to move one pixel at a
time.
Note
2. The Orbiter does not function while the MAGNIFY feature is in
use.
and soften the image.
• OFF: Turns the SOFTEN function off.
• 1, 2, 3, 4: Activates the SOFTEN setting. Higher numbers create a “softer” image.
phase of incoming computer signals for optimum picture quality whenever the display is
turned on, or when a different input or input signal type is selected. To enable this feature,
Under some conditions – such as when the input signal consists of
Note
mostly dark colors – Auto Setup may not produce the desired
results. If this occurs, set Auto Setup Mode to OFF and manually
42
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Function: The CinemaWall can automatically switch to Input 1 or Input 4 (Model
SP-50/SP-60 only) when an image signal is detected at that input. To enable this feature,
Model SP-50/SP-60).
After Auto Function triggers an input switch, when the Input 1 or Input 4 signal is no longer
present, the input source reverts to the previously-selected input.
On the Model SP-42, Auto Function is supported on Input 1 only.
Note
The input signal must be RGB with composite or separate sync;
Auto Function will not work with sync-on-green RGB or component
signals.
When Auto Function is active, selecting an input manually causes
Auto Function to be temporarily disabled. If you cycle power to the
CinemaWall, Auto Function becomes active again.
menu to program the screen maintenance features of the CinemaWall to operate at
regular intervals. This is useful for preventing image burn-in.
Option (Installer Adjust
Mode)
INPUT 3
OPTION
INSTALLER ADJ.
PICTURE
SCREEN
SET-UP
PROGRAM TIMER
You can program the CinemaWall to switch inputs and/or replace the normal source
signal with a white field, an inverse image or an “orbiting” image. You can specify a time of
day and day of the week when you want this to take place.
TEST PATTERN
SIDEBAR ADJ.
BAUD RATE
:
OFF
:
:
9600BPS
ALL
ID NUMBER
To set up a screen maintenance program:
MENU
SET
ENTER
EXIT
1. Press SET to select the DATE field for the first program. Press or to select one of
the following:
• SUN, MON, TUE, WED, THU, FRI or SAT for a program that runs once only on the
next occurrence of that day.
• * for a program that runs daily.
• *SUN, *MON, *TUE, *WED, *THU, *FRI or *SAT for a program that runs weekly on
that day.
2. Press SET, then
3. Press or to set the hour component of the start time.
4. Press , then or to set the minute component of the start time.
followed by SET again to set the program start time.
5. Press SET, then followed by SET again to set the program end time (repeat steps 3
and 4).
6. Press SET, then
followed by SET again to specify an input associated with this
program. Choose “–” to specify the input that was active when the CinemaWall was
last powered off.
7. Press SET, then
followed by SET again to select the PATTERN field for this
or to select one of the following:
PROGRAM TIMER
program. Press
DATE
*
*
*
–
–
–
–
ON
OFF
INPUT
PATTERN
–
WHITE
–
–
–
–
–
10:00
20:00
– –:– –
– –:– –
– –:– –
– –:– –
– –:– –
– –:– –
– –:– –
21:00
– –:– –
– –:– –
– –:– –
– –:– –
–
–
–
–
–
–
–
• Choose “–” to specify the function that was active when the CinemaWall was last
powered off.
• Choose WHITE to display a white field.
RETURN
• Choose INVERSE to display an inverse image.
• Choose ORBITER to display an “orbiting” image.
SET
ENTER
MENU
EXIT
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press SET.
9. Repeat steps 1 through 8 as desired to create additional screen maintenance
programs.
To clear a screen maintenance program, move the cursor to the DATE field and press
CLEAR on the remote control, using a straightened paper clip or similar object.
Select Return to exit the Program Timer menu.
normal picture on-screen, or a single color. Use this feature to repair burned-in areas of
the display.
Press SET repeatedly to select INVERSE or a single color to display. Then, press MENU.
To select a different pattern or return to the normal picture, press the Installer Adjust menu
button, select Option, then select Test Pattern. Press SET repeatedly to select OFF or
another pattern.
sides of the screen when the Aspect Ratio is set to Standard 4:3 or 14:9 (refer to Table
4-1). The range is from 0 to +255 for each color component (red, green and blue); the
default setting is +80 (gray).
When the 4:3 or 14:9 aspect ratio is selected, the CinemaWall can gradually shift the
inactive areas of the display in small increments every time it is turned on, to prevent
Sidebar Adjust menu and set it to ON.
specifically instructed to do so by Runco Technical Support!
ID Number: The ID Number uniquely identifies the CinemaWall in multiple-panel or
video-wall installations. It is used to address serial commands to a specific panel when
two or more are daisy-chained together via the COMBINATION IN/OUT connectors (see
CinemaWall’s cooling fan.
INPUT 3
OPTION
AUTO
INSTALLER ADJ.
PICTURE
SCREEN
SET-UP
FAN SPEED
OSD
FRONT L.E.D.
ISF SETTINGS
RUNCO PRO
FRC
:
In most cases, the default Fan Speed (AUTO) will maintain the correct operating
temperature. If the CinemaWall frequently turns off due to overheating, or in certain
high-altitude operating environments, you may need to change this setting to MAX.
:
:
ON
ISF CCC
:
NORMAL
SET
ENTER
MENU
EXIT
and behavior.
CinemaWall displays your selection on-screen. When you adjust the volume or press
MUTE on the remote control, a slidebar appears as a visual indicator of the level.
To prevent the display of these items, select Display from the OSD menu and set it to
OFF.
LARGE).
Select Return to exit the OSD menu.
44
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
operating status as follows:
• Lights green to indicate normal operation;
• Flashes green (once per second) when the AUTO OFF feature is active;
• Lights red to indicate that the CinemaWall is in standby mode;
• Flashes green or red (twice per second) to indicate an error condition.
When set to OFF, the LED lights red when the CinemaWall is in standby mode; otherwise,
it is off.
allows you to create two, independent sets of image quality settings and switch from one
to the other by selecting a color mode.
ISF CCC. Any subsequent changes to image quality settings are stored and can be
recalled by selecting that color mode.
The ISF CCC color mode is pre-set to approximately 3,200K.
Note
processing settings.
normal effective data area for a video signal.
To use Underscan, select it from the Runco Pro menu and set it to ON. Then, exit the
menu system and use the ASPECT RATIO remote control button to select Underscan
mode.
MONOTONE to remove all color information from the image. Select HIGH CNT to
increase the color temperature by approximately 2,000K.
MOTION. However, with certain interlaced and/or composite video images with few or
no moving objects, STILL or NON-STD may yield better results.
NORMAL if you notice and want to minimize motion blur when viewing source material
that originated from film. If frame rate conversion is not needed, set FRC to SCALER.
signal is displayed when you turn on the CinemaWall. You can also specify an initial audio
volume level.
INPUT 3
OPTION
INSTALLER ADJ.
PICTURE
SCREEN
SET-UP
POWER ON MODE
SEAMLESS SW
PICTURE ORIENT.
FUNCTION RESET
:
:
OFF
OFF
You can select a specific input or volume level (0 to 42). Or, select LAST to have the
CinemaWall set the input and volume to what they were the last time it was turned off.
SET
ENTER
MENU
EXIT
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
CinemaWall inputs using the SWAP button on the remote control. To enable it, select
you want to associate with this feature in the SELECT1 and SELECT2 fields.
By default, Input 1 and Input 2 are selected, so that when Input 1 is active, pressing
SWAP switches to Input 2 and vice versa.
Seamless Switch is not available when using PIP.
Note
a ceiling, you may want to mount it upside down and run the cables upward (toward the
ceiling) to make them less visible. In this case, you would select “FLIP HV.”
Normal operating state
OFF
Left-right reversal
FLIP H
Up-down, left-right reversal
Up-down reversal
FLIP V
FLIP HV
Figure 4-8. Picture Orientation
Reset from the Option menu. Then, press to highlight YES and press SET. This action
resets ALL settings (except the display ID Number) to their default values, as set at the
factory.
This action is not undoable. Proceed with caution!
Caution
46
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4.8
Using
PIP is currently supported on Input 1 and Input 2 only.
Note
Picture-In-Picture (PIP)
To use PIP, press the SPLIT button.
PIP FUNCTION
SPLIT SUB INPUT
SWAP
PIP SHIFT
MUTE
VOLUME
+
-
The PIP sub-window appears beside the main
image window.
Press SPLIT again to display the sub-window
superimposed on the main window.
Press SPLIT again to turn PIP off.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a PIP Source
Press the SUB INPUT button to select a PIP signal
source.
➤
➤
PIP FUNCTION
SPLIT SUB INPUT
SWAP
PIP SHIFT
MUTE
VOLUME
-
+
Swapping the Main and
PIP Windows
Press the SWAP button to replace the main screen
with the sub-screen or vice versa. (This switches the
audio input as well.)
PIP FUNCTION
SPLIT SUB INPUT
SWAP
PIP SHIFT
MUTE
VOLUME
+
-
Changing the PIP Position
To change the PIP window position, press the
PIP SHIFT button on the remote control repeatedly
until the window is in the desired position.
➤
PIP FUNCTION
SPLIT SUB INPUT
SWAP
PIP SHIFT
MUTE
VOLUME
+
-
3
4
2
1
48
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The CinemaWall allows you to zoom in on a portion of the displayed image. To use this
feature, press the MAGNIFY button repeatedly to select one of four zoom levels
subscreen appears in the upper-right corner of the display.
4.9
Enlarging One Part of
the Screen
Use the directional buttons ( / / / ) to select a magnified image area to display. As
you do this, a green plus sign (+) appears in the subscreen to indicate the center of the
enlarged area.
Magnification Level 3 (2x)
Magnification Level 1 (Normal Size)
+
Zoom-Area subscreen
Figure 4-9. Viewing an Enlarged Area of the Display
1. You cannot change the aspect ratio while using the MAGNIFY
function.
Note
2. The MAGNIFY function is cancelled if the input signal changes,
or if you switch inputs or select PIP mode.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
50
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Maintenance and Troubleshooting
Regular cleaning will extend the life and performance of the CinemaWall. Before cleaning,
be sure to unplug the power cord from the power outlet.
5.1
Cleaning
Do not under any circumstances use solvents such as benzene or thinner to clean the
CinemaWall. Doing so may cause deterioration or peeling of paint from the display or
remote control unit.
Cleaning the Display
Panel Body and Remote
Control
Wipe the display and remote control gently with a soft cloth. In the case of excessive dirt
buildup, dampen a soft cloth with a diluted neutral cleaning detergent and after wringing
the cloth thoroughly, wipe the component and then dry it with a dry soft cloth.
After dusting, wipe the screen gently using the supplied cleaning cloth or another soft
cloth (cotton, flannel etc.). Do not use tissue or a rough cloth. The screen surface is easily
scratched; do not rub it or hit it with a hard object.
Cleaning the Screen
Cleaning the Vents
If you clean the surface of the screen with a wet cloth, water droplets on the surface may
enter into the product and cause a malfunction.
As a general rule, use a vacuum cleaner about once a month to clean the vents on the
rear panel of the display of dust buildup (set the vacuum cleaner to its weakest setting
when doing this). If not removed, accumulated dust can cause the internal temperature to
increase, resulting in possible breakdown or fire.
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the CinemaWall. If the suggested solutions fail to resolve the problem or if
you encounter an issue not described here, please contact your Runco dealer or Runco
Technical Support.
5.2
Troubleshooting Tips
Table 5-1. Troubleshooting Chart
Symptom
Possible Cause(s)
Solution
The display does not turn on
after initial installation.
• The CinemaWall is not
plugged in or the AC outlet
is not active.
• Ensure that the
CinemaWall is plugged in
and that the AC outlet is
active.
• The remote control
batteries have run out.
• Replace the batteries.
The display is on, but there is
no picture or sound.
• Incorrect source selection.
• Source component is not
turned on.
• Select the correct source.
• Turn on the source
component.
• Source component is
connected incorrectly or
not at all.
• Check video connections
to source component.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. Troubleshooting Chart (continued)
Symptom
Possible Cause(s)
Solution
Picture is okay, but there is no
sound.
• Audio output is muted.
• Press the MUTE button
on the remote control.
• Volume setting is too low.
• Source component is
connected incorrectly or
not at all.
• Turn up the volume.
• Check audio connections
to source component.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high.
• Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Brightness is set too high.
• Lower the brightness
setting.
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
• Incorrect color space
setting.
• Select the correct color
space (refer to Color
• Ensure that the YPbPr
(component) source
output connections to
Input 4 are correct (see
• The Pr, Y or Pb outputs
from the source to Input 4
on the CinemaWall are
incorrect.
RGB-HD images appear
“noisy.”
• Frequency and Phase
settings need adjustment.
• Manually adjust Frequency
and Phase settings, or
perform an Auto Setup
page 38).
One of the following error
messages appears
on-screen:
• CAUTION
OUT OF RANGE
• CAUTION
• The resolution and
frequency of the video
card in the computer are
not compatible with the
CinemaWall.
• Select a compatible
resolution and vertical
frequency (refer to
UNSUPPORTED SIGNAL
• SIGNAL NG
The image is too large or too
small.
• Image size needs
adjusting.
• Adjust the image size (refer
One of the following error
messages appears
on-screen:
• Ambient temperature is
too high.
• Turn off main power.
Remove any objects
blocking the cooling vents
on the CinemaWall and/or
clean the vents.
• WARNING
THERMAL ALERT
SHUT DOWN (**)
• WARNING
• Cooling fan has
malfunctioned.
• Immediately turn off
power, remove the power
plug from its outlet, and
consult your Runco dealer.
FAN FAILURE
SHUT DOWN (**)
(“(**)” represents a two-digit
error code.)
52
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Serial Communications
To interface the CinemaWall with a home theater automation/control system or a PC
running terminal emulation software, connect it to your control system or PC as shown in
6.1
RS-232 Connection
and Port Configuration
Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop
bit and no flow control. Set its baud rate to 115200, to match that of the CinemaWall
RS-232 port.
Serial commands to the CinemaWall take the following form:
• You can send commands in either hexadecimal or ASCII format.
• ASCII commands are not case-sensitive.
6.2
Serial Command
Syntax
• Commands begin with the “Start of Text” (STX) character (02h or <Ctrl> Bin ASCII),
followed by the display ID (2 bytes), the command data and command argument
<Ctrl> Cin ASCII).
• You do not need to send a carriage return after the command.
• The default CinemaWall display ID is 01 (30h 31h). With most commands, you can also
use the “wildcard” display ID of “**” (2Ah 2Ah) in place of any value for the ID. However,
when requesting status via serial commands, you must use a specific display ID; “**”
does not work in these cases.
For example, if the CinemaWall ID number is set to its default value (01 = 30h 31h), send
the following sequence to set the contrast to its highest possible level (255):
Example
STX
ID (2 bytes) Command (3 bytes) Argument (3 bytes)
ETX
30 31
02
or
43 4E 54
32 35 35
03
Hex
2A 2A
0 1
or
<Ctrl> B
C N T
2 5 5
<Ctrl> C
ASCII
* *
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1 lists the CinemaWall serial command set. Except where indicated, adjustments
made using serial commands are stored in the same memory as those made in Installer
Adjust mode.
Table 6-1. Serial Commands
Command
HEX
Value Range
Minimum Maximum
Power
Description
ASCII
POF
PON
50 4F 46
50 4F 4E
–
–
–
–
Power OFF.
Power ON.
Input Select (Note 1)
IN1
IN2
IN3
IN4
IN5
49 4E 31
49 4E 32
49 4E 33
49 4E 34
49 4E 35
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Switches the main screen to INPUT1.
Switches the main screen to INPUT2.
Switches the main screen to INPUT3.
Switches the main screen to INPUT4.
Switches the main screen to INPUT5.
Switches the main screen to INPUT1.
Switches the main screen to INPUT2.
Switches the main screen to INPUT3.
Switches the main screen to INPUT4.
Switches the main screen to INPUT5.
Switches the sub screen to INPUT1.
Switches the sub screen to INPUT2.
Outputs main input to the full screen.
Outputs sub input to the full screen.
–
–
–
–
INPS01 49 4E 50 53 30 31
INPS02 49 4E 50 53 30 32
INPS03 49 4E 50 53 30 33
INPS04 49 4E 50 53 30 34
INPS05 49 4E 50 53 30 35
SSIS01 53 53 49 53 30 31
SSIS02 53 53 49 53 30 32
–
–
–
–
–
–
–
SWM
SWS
53 57 4D
53 57 53
–
–
Aspect Ratio
AST
41 53 54
–
–
–
–
–
–
–
–
Executes AUTO SETUP on Input 1.
Sets the aspect ratio to PIX by PIX.
Sets the aspect ratio to Standard 4:3.
SZMS00 53 5A 4D 53 30 30
SZMS01 53 5A 4D 53 30 31
SZMS02 53 5A 4D 53 30 32
Sets the aspect ratio to ANAMORPHIC
16:9.
SZMS03 53 5A 4D 53 30 33
SZMS05 53 5A 4D 53 30 35
Notes:
–
–
–
–
Sets the aspect ratio to LETTERBOX.
Sets the aspect ratio to VIRTUALWIDE.
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
54
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
Value Range
Description
ASCII
Minimum Maximum
SZMS06 53 5A 4D 53 30 36
SZMS09 53 5A 4D 53 30 39
SZMS10 53 5A 4D 53 31 30
–
–
–
–
–
–
Sets the aspect ratio to 14:9.
Sets the aspect ratio to UNDERSCAN.
Sets the aspect ratio to VIRTUAL
CINEMA.
Video
PMTS00 50 4D 54 53 30 30
PMTS01 50 4D 54 53 30 31
STLS00 53 54 4C 53 30 30
–
–
–
–
–
–
Turns video muting off. (Note 2)
Turns video muting on. (Note 2)
Turns the STILL setting to OFF.
(Note 2)
STLS01 53 54 4C 53 30 31
–
–
Turns the STILL setting to ON. (Note 2)
Audio
AMTS00 41 4D 54 53 30 30
AMTS01 41 4D 54 53 30 31
AUSS01 41 55 53 53 30 31
AUSS02 41 55 53 53 30 32
–
–
–
–
Turns audio mute OFF. (Note 2)
Turns audio mute ON. (Note 2)
Sets audio source to main.
Sets audio source to sub.
Adjusts the audio volume.
–
–
–
–
VOL
56 4F 4C
000
042
Picture-in-Picture (PIP)
MSCS00 4D 53 43 53 30 30
MSSS01 4D 53 53 53 30 31
–
–
–
–
Turns 2-screen display operation OFF.
Sets PIP sub-screen size to 1 (small-
est).
MSSS02 4D 53 53 53 30 32
MSSS03 4D 53 53 53 30 33
MSSS04 4D 53 53 53 30 34
MSTS01 4D 53 54 53 30 31
–
–
–
–
–
–
–
–
Sets PIP sub-screen size to 2.
Sets PIP sub-screen size to 3.
Sets PIP sub-screen size to 4 (largest).
Sets 2-screen operation to 2 SCREEN
(side-by-side; main screen on left).
Notes:
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
Value Range
Description
ASCII
Minimum Maximum
MSTS02 4D 53 54 53 30 32
MSTS03 4D 53 54 53 30 33
MSTS04 4D 53 54 53 30 34
MSTS05 4D 53 54 53 30 35
MSTS06 4D 53 54 53 30 36
–
–
–
–
–
–
–
–
–
–
Sets 2-screen operation to PinP (lower
right).
Sets 2-screen operation to PinP (upper
right).
Sets 2-screen operation to PinP (upper
left).
Sets 2-screen operation to PinP (lower
left).
Sets 2-screen operation to PoutP
(side-by-side; small sub-screen on left).
MSTS08 4D 53 54 53 30 38
MSTS09 4D 53 54 53 30 39
–
–
–
–
Swaps main and sub-screens in PIP
2-screen mode.
Sets 2-screen operation to PoutP
(side-by-side; small sub-screen on
right).
MSTS10 4D 53 54 53 31 30
–
–
Sets 2-screen operation to 2 SCREEN
(side-by-side, full height; main screen
on left).
Notes:
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
56
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
MSTS11 4D 53 54 53 31 31
Value Range
Description
ASCII
Minimum Maximum
–
–
Sets 2-screen operation to 2 SCREEN
(side-by-side, full height; main screen
on left).
MSTS12 4D 53 54 53 31 32
–
–
Sets 2-screen operation to 2 SCREEN
(side-by-side, full height; main screen
on left).
Functional Lock
FCLS00 46 43 4C 53 30 30
FCLS01 46 43 4C 53 30 31
–
–
–
–
Clears the FUNCTIONAL LOCK.
Locks the main-control panel button
control.
FCLS02 46 43 4C 53 30 32
FCLS03 46 43 4C 53 30 33
FCLS04 46 43 4C 53 30 34
–
–
–
–
–
Locks the remote-control button con-
trol.
Locks both main-control panel and
remote button control.
–
OSD
–
Sets the MEMORY LOCK.
DOF
44 4F 46
–
Clears the current displayed OSD.
(Note 2)
SET-UP Menu Commands
CTPS01 43 54 50 53 30 31
CTPS02 43 54 50 53 30 32
CTPS03 43 54 50 53 30 33
CTPS04 43 54 50 53 30 34
Notes:
–
–
–
–
–
–
–
–
Sets COLOR TEMP. to LOW.
Sets COLOR TEMP. to MID-LOW.
Sets COLOR TEMP. to MIDDLE.
Sets COLOR TEMP. to MID-HIGH.
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
Value Range
Description
ASCII
Minimum Maximum
CTPS05 43 54 50 53 30 35
CTRS00 43 54 52 53 30 30
CTRS01 43 54 52 53 30 31
DBLS01 44 42 4C 53 30 31
–
–
–
–
–
–
–
–
Sets COLOR TEMP. to HIGH.
Sets CHROMA EE to OFF.
Sets CHROMA EE to ON.
Sets BLACK LEVEL for INPUT 2 to
LOW.
DBLS02 44 42 4C 53 30 32
–
–
Sets BLACK LEVEL for INPUT 2 to
HIGH.
DNRS00 44 4E 52 53 30 30
DNRS01 44 4E 52 53 30 31
DNRS02 44 4E 52 53 30 32
DNRS03 44 4E 52 53 30 33
DSGS01 44 53 47 53 30 31
–
–
–
–
–
–
–
–
–
–
Sets the VIDEO NR to OFF.
Sets the VIDEO NR to LOW.
Sets the VIDEO NR to MIDDLE.
Sets the VIDEO NR to HIGH.
Sets PLUG/PLAY setting for INPUT 2
to PC.
DSGS02 44 53 47 53 30 32
–
–
Sets PLUG/PLAY setting for INPUT 2
to VIDEO.
MCDS01 4D 43 44 53 30 31
MCDS02 4D 43 44 53 30 32
–
–
–
–
Sets COLOR SPACE to RGB (VIDEO).
Sets COLOR SPACE to
COMPONENT1 (YCbCr).
MCDS03 4D 43 44 53 30 33
–
–
Sets COLOR SPACE to
COMPONENT2 (YPbPr).
MNRS00 4D 4E 52 53 30 30
MNRS01 4D 4E 52 53 30 31
MNRS02 4D 4E 52 53 30 32
MNRS03 4D 4E 52 53 30 33
PUCS00 50 55 43 53 30 30
PUCS01 50 55 43 53 30 31
SFTS01 53 46 54 53 30 31
SFTS02 53 46 54 53 30 32
SFTS03 53 46 54 53 30 33
SFTS04 53 46 54 53 30 34
SFTS05 53 46 54 53 30 35
Notes:
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Turns MPEG FILTER OFF.
Sets MPEG FILTER to LOW.
Sets MPEG FILTER to MIDDLE.
Sets MPEG FILTER to HIGH.
Turns FILM MODE OFF.
Turns FILM MODE ON.
Sets the SIGNAL FORMAT to Type1.
Sets the SIGNAL FORMAT to Type2.
Sets the SIGNAL FORMAT to Type3.
Sets the SIGNAL FORMAT to Type4.
Sets the SIGNAL FORMAT to Type5.
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
58
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
Value Range
Description
ASCII
Minimum Maximum
SFTS06 53 46 54 53 30 36
SFTS07 53 46 54 53 30 37
SFTS08 53 46 54 53 30 38
SFTS10 53 46 54 53 31 30
–
–
–
–
–
–
–
–
Sets the SIGNAL FORMAT to Type6.
Sets the SIGNAL FORMAT to Type7.
Sets the SIGNAL FORMAT to Type8.
Sets the SIGNAL FORMAT to Type10.
OPTION Menu Commands
ESVS00 45 53 56 53 30 30
ESVS01 45 53 56 53 30 31
ESVS02 45 53 56 53 30 32
ESVS03 45 53 56 53 30 33
ESVS04 45 53 56 53 30 34
–
–
–
–
–
–
–
–
–
–
Sets the ENERGY MODE setting to
AVERAGE.
Sets the ENERGY MODE setting to
LEVEL1 (energy saving).
Sets the ENERGY MODE setting to
LEVEL2 (fixed brightness).
Sets the ENERGY MODE setting to
LEVEL3 (long life).
Sets the ENERGY MODE setting to
AUTO.
ORBS00 4F 52 42 53 30 30
ORBS01 4F 52 42 53 30 31
ORBS02 4F 52 42 53 30 32
ORBS03 4F 52 42 53 30 33
SOFS00 53 4F 46 53 30 30
SOFS01 53 4F 46 53 30 31
SOFS02 53 4F 46 53 30 32
SOFS03 53 4F 46 53 30 33
SSTS00 53 53 54 53 30 30
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Turns ORBITER OFF.
Sets ORBITER to TYPE 1.
Sets ORBITER to TYPE 2.
Sets ORBITER to TYPE 3.
Turns SOFTEN OFF.
Sets SOFTEN to 1.
Sets SOFTEN to 2.
Sets SOFTEN to 3.
Sets STILL IMAGE FREEZE to OFF (still
image fills screen).
SSTS01 53 53 54 53 30 31
SSTS02 53 53 54 53 30 32
–
–
–
–
Sets STILL IMAGE FREEZE to
SIDE-BY-SIDE (still image next to mov-
ing image).
Sets STILL IMAGE FREEZE to PinP (still
image in sub-screen with moving
image).
TPH
54 50 48
000
023
Sets the hour of the present time.
Notes:
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
54 50 4D
Value Range
Description
ASCII
Minimum Maximum
TPM
000
059
Sets the minute of the present time.
Deactivates program timer.
Activates program timer.
TPTS00 54 50 54 53 30 30
TPTS01 54 50 54 53 30 31
–
–
–
–
TPW
54 50 57
001
007
Sets the day of the week of the present
time (001 = Sunday ... 007 = Saturday).
TSMS00 54 53 4D 53 30 30
TSMS01 54 53 4D 53 30 31
–
–
–
–
Sets Daylight Saving Time to OFF.
Sets Daylight Saving Time to ON.
PICTURE Menu Commands (Installer Adjust Mode)
BHI
BLW
BRT
CGB
CGC
CGG
CGM
CGR
CGY
CNT
COL
ENH
ENV
GHI
42 48 49
42 4C 57
42 52 54
43 47 42
43 47 43
43 47 47
43 47 4D
43 47 52
43 47 59
43 4E 54
43 4F 4C
45 4E 48
45 4E 56
47 48 49
47 4C 57
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
–
255
255
255
060
060
060
060
060
060
255
127
015
015
255
255
–
Adjusts blue gain (highlight).
Adjusts blue offset (lowlight).
Adjusts brightness.
Adjusts BLUE color detail.
Adjusts CYAN color detail.
Adjusts GREEN color detail.
Adjusts MAGENTA color detail.
Adjusts RED color detail.
Adjusts YELLOW color detail.
Adjusts contrast.
Adjusts color intensity.
Adjusts H. SHARPEN.
Adjusts V. SHARPEN.
Adjusts green gain (highlight).
Adjusts green offset (lowlight).
Sets the GAMMA to 1.8.
Sets the GAMMA to 1.9.
Sets the GAMMA to 2.0.
Sets the GAMMA to 2.1.
Sets the GAMMA to 2.2.
Sets the GAMMA to 2.3.
GLW
GRAS18 47 52 41 53 31 38
GRAS19 47 52 41 53 31 39
GRAS20 47 52 41 53 32 30
GRAS21 47 52 41 53 32 31
GRAS22 47 52 41 53 32 32
GRAS23 47 52 41 53 32 33
Notes:
–
–
–
–
–
–
–
–
–
–
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
60
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
GRAS24 47 52 41 53 32 34
Value Range
Description
ASCII
Minimum Maximum
–
–
Sets the GAMMA to 2.4.
Adjusts red gain (highlight).
Adjusts red offset (lowlight).
Adjusts the SHARPNESS.
RHI
RLW
SHP
STD
52 48 49
52 4C 57
53 48 50
53 54 44
000
000
000
–
255
255
015
–
Executes FACTORY and WHITE BAL.
RESET commands.
TNT
54 4E 54
000
060
Adjusts the TINT.
SCREEN Menu Commands (Installer Adjust Mode)
CFR
CPH
FRP
HPS
HSI
43 46 52
43 50 48
46 52 50
48 50 53
48 49 53
56 50 53
56 53 49
000
000
–
255
031
–
Adjusts clock (PLL) frequency.
Adjusts PLL phase.
Executes IMAGE RESET.
Adjusts Horizontal position .
Adjusts Horizontal size (width).
Adjusts the Vertical position.
Adjusts Vertical size (height).
064
000
064
000
191
064
191
064
VPS
VSI
SET-UP Menu Commands (Installer Adjust Mode)
000 020 Adjusts the sub-volume.
OPTION Menu Commands (Installer Adjust Mode)
SVL
53 56 4C
BPIS01 42 50 49 53 30 31
BPIS02 42 50 49 53 30 32
BPPS00 42 50 50 53 30 30
BPPS01 42 50 50 53 30 31
BPPS02 42 50 50 53 30 32
–
–
–
–
–
–
–
–
–
–
Sets BANNER PIP input to INPUT1.
Sets BANNER PIP input to INPUT2.
Sets BANNER PIP to OFF.
Sets BANNER PIP position to TOP.
Sets BANNER PIP position to
MID-HIGH.
BPPS03 42 50 50 53 30 33
BPPS04 42 50 50 53 30 34
–
–
–
–
Sets BANNER PIP position to
MID-LOW.
Sets BANNER PIP position to BOT-
TOM.
BSL
42 53 4C
000
–
255
–
Adjusts BLUE sidebar level.
CLMS00 43 4C 4D 53 30 30
Sets the ISF SETTING to NORMAL.
Notes:
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
CLMS01 43 4C 4D 53 30 31
Value Range
Description
ASCII
Minimum Maximum
–
–
–
–
–
–
–
–
–
–
–
–
Sets the ISF SETTING to ISF CCC.
Sets FAN SPEED to AUTO.
FCA
FDT
FCM
46 43 41
46 44 54
46 43 4D
Executes FUNCTION RESET.
Sets FAN SPEED to MAX.
FMKS00 46 4D 4B 53 30 30
FMKS02 46 4D 4B 53 30 32
Sets the TEST PATTERN to OFF.
Sets the TEST PATTERN to INVERSE
(negative-positive inversion).
FMKS03 46 4D 4B 53 30 33
FMKS04 46 4D 4B 53 30 34
FMKS05 46 4D 4B 53 30 35
FMKS06 46 4D 4B 53 30 36
FMKS07 46 4D 4B 53 30 37
FRCS00 46 52 43 53 30 30
FRCS01 46 52 43 53 30 31
–
–
–
–
Turns ON the WHITE test pattern.
Turns ON the RED test pattern.
Turns ON the GREEN test pattern.
Turns ON the BLUE test pattern.
Turns ON the YELLOW test pattern.
Sets FRC to SCALER.
–
–
–
–
–
–
–
–
–
–
Sets FRC to NORMAL.
GSL
IDC
47 53 4C
49 44 43
000
–
255
–
Adjusts the GREEN sidebar level.
Clears the display ID number (resets to
“ALL”); for example, 01IDC.
IDS
49 44 53
–
–
Sets the display ID number; for exam-
ple, 01IDSsets the display ID to 01h.
Note: IDS only works if the display ID
number has been cleared (with IDC) or
has not been previously assigned.
IPRS01 49 50 52 53 30 31
–
–
Sets the DISPLAY PROFILE to NOR-
MAL.
IPRS02 49 50 52 53 30 32
IPRS03 49 50 52 53 30 33
–
–
–
–
Sets the DISPLAY PROFILE to PURE.
Sets the DISPLAY PROFILE to MONO-
TONE.
IPRS04 49 50 52 53 30 34
–
–
Sets the DISPLAY PROFILE to HIGH
CONTRAST.
LESS00 4C 45 53 53 30 30
LESS01 4C 45 53 53 30 31
Notes:
–
–
–
–
Sets FRONT L.E.D. to OFF.
Sets FRONT L.E.D. to ON.
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
62
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
Value Range
Description
ASCII
Minimum Maximum
OSDS00 4F 53 44 53 30 30
OSDS01 4F 53 44 53 30 31
OSSS01 4F 53 53 53 30 31
OSSS02 4F 53 53 53 30 32
PTRS00 50 54 52 53 30 30
–
–
–
–
–
–
–
–
–
–
Sets OSD DISPLAY to OFF.
Sets OSD DISPLAY to ON.
Sets OSD SIZE to LARGE.
Sets OSD SIZE to SMALL.
Sets sub-screen translucence to OFF
(0%).
PTRS01 50 54 52 53 30 31
PTRS02 50 54 52 53 30 32
PTRS03 50 54 52 53 30 33
PTRS04 50 54 52 53 30 34
PTRS05 50 54 52 53 30 35
PTRS06 50 54 52 53 30 36
PTRS07 50 54 52 53 30 37
PTRS08 50 54 52 53 30 38
–
–
Sets sub-screen translucence to 10%.
Sets sub-screen translucence to 20%.
Sets sub-screen translucence to 30%.
Sets sub-screen translucence to 40%.
Sets sub-screen translucence to 50%.
Sets sub-screen translucence to 60%.
Sets sub-screen translucence to 70%.
Sets sub-screen translucence to 80%.
RSL
52 53 4C
000
–
255
–
Adjusts the RED sidebar level.
Sets SEAMLESS SWITCH to OFF.
Sets SEAMLESS SWITCH to ON.
SLSS00 53 4C 53 53 30 30
SLSS01 53 4C 53 53 30 31
–
–
SL1S01 53 4C 31 53 30 31
SL1S02 53 4C 31 53 30 32
SL1S03 53 4C 31 53 30 33
SL1S04 53 4C 31 53 30 34
SL1S05 53 4C 31 53 30 35
–
–
Sets SEAMLESS SWITCH SELECT 1
to INPUT 1... INPUT 5.
SL2S01 53 4C 32 53 30 31
SL2S02 53 4C 32 53 30 32
SL2S03 53 4C 32 53 30 33
SL2S04 53 4C 32 53 30 34
SL2S05 53 4C 32 53 30 35
–
–
Sets SEAMLESS SWITCH SELECT 2
to INPUT 1... INPUT 5.
USCS00 55 53 43 53 30 30
USCS01 55 53 43 53 30 31
Notes:
–
–
–
–
Turns the UNDERSCAN setting OFF.
Turns the UNDERSCAN setting ON.
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Command
HEX
Value Range
Description
ASCII
Minimum Maximum
Adjustment Commands
Use these commands in place of a numeric value after a command that requires one, such as the
brightness (BRT) command. For example, if the current Brightness setting is 128, you can use
either BRTDW0or BRT118to reduce the setting by 10.
DW1
DW2
DW3
DW4
DW5
DW6
DW7
DW8
DW9
44 57 31
44 57 32
44 57 33
44 57 34
44 57 35
44 57 36
44 57 37
44 57 38
44 57 39
–
–
Reduces adjustment value by n
(n = 1 to 9).
DW0
DWF
44 57 30
44 57 46
–
–
–
–
Reduces adjustment value by 10.
Sets the adjustment value to the mini-
mum value.
UP1
UP2
UP3
UP4
UP5
UP6
UP7
UP8
UP9
55 50 31
55 50 32
55 50 33
55 50 34
55 50 35
55 50 36
55 50 37
55 50 38
55 50 39
–
–
Adds n to the adjustment value
(n = 1 to 9).
UP0
UPF
55 50 30
55 50 46
–
–
–
–
Adds 10 to the adjustment value.
Sets the adjustment value to maximum.
Notes:
1. When making input-specific adjustments such as to image quality, screen position/size or audio
sub-volume, select the input you wish to affect before making such adjustments.
2. These settings are not stored in memory.
64
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Specifications
Table 7-1 lists the CinemaWall specifications.
7.1
CinemaWall
Specifications
Table 7-1. CinemaWall Specifications
Native Resolution:
Model SP-42: 1024 x 768
Model SP-50: 1365 x 768
Model SP-60: 1365 x 768
Screen Size (diagonal):
Active Screen Area:
Model SP-42: 42 in.
Model SP-50: 50 in.
Model SP-60: 60 in.
Model SP-42: 36.28 x 20.29 in. (921.6 x 515.3 mm)
Model SP-50: 43.45 x 24.50 in. (1103.6 x 622.3 mm)
Model SP-60: 51.93 x 29.21 in. (1319.0 x 741.9 mm)
Screen Aspect Ratio:
16:9
Available Aspect Ratios:
Standard 4:3, Letterbox, 16:9 Anamorphic, VirtualWide™,
Virtual Cinema™, 14:9, Pix-by-Pix (no re-sizing)
DTV Compatibility:
ISF Settings:
480i/p, 525i/p, 540p, 625i/p, 720p, 1035i, 1080i; 50/60 Hz
Yes
Data/Graphics Compatibility:
Inputs:
Refer to Table 7-2
(1) RGB/Component (15-pin D-sub); compatible with
Microsoft “Plug & Play” (VESA DDC 1/2B)
(1) DVI with HDCP; compatible with Microsoft “Plug & Play”
(VESA DDC 2B)
(1) Composite Video or S-Video (switch-selectable)
(1) HD Component
(1) DVI Video with HDCP
(5) Audio (stereo mini-jack); 500 mV RMS / > 10 kΩ
(1) RS-232 (9-pin D-sub female)
Outputs:
(1) RGB (15-pin D-sub)
(1) Speaker Terminals (stereo pair)
(1) Audio (stereo mini-jack); 500 mV RMS / < 5 kΩ
Audio System:
Internal amplifier
Output Power =
8W RMS x 2 at 6Ω (Model SP-42)
9W RMS x 2 at 6Ω (Models SP-50 and SP-60)
Power Requirements:
100 to 240 VAC, 50/60Hz
Power Consumption:
Model SP-42: 360 watts (1.5 watts in standby), maximum
Model SP-50: 375 watts (1.5 watts in standby), maximum
Model SP-60: TBD
Operating Environment:
40ºF to 95ºF (5ºC to 35ºC);
20% to 80% humidity (non-condensing)
Altitude = up to 6,000 feet (1,828m)
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-1. CinemaWall Specifications (continued)
Dimensions:
Weight (with Stand):
Limited Warranty:
Model SP-42: 83.0 lbs. (37.65 kg)
Model SP-50: 94.2 lbs. (42.73 kg)
Model SP-60: 150.5 lbs. (68.27 kg)
Three (3) years parts and labor from the date of delivery to
the end user (except for plasma glass panel).
Plasma Glass Panel: One (1) year parts and labor from the
date of delivery to the end user.
Specifications are subject to change without notice.
66
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The CinemaWall can display video signals from a variety of computer sources via INPUT 1
and INPUT 2.
7.3
Computer/VideoSignal
Compatibility
Table 7-2 lists the signal types that are compatible with the CinemaWall.
Table 7-2. Computer/Video Signal Compatibility Chart
Refresh Rate
Input
Resolution
(DotsxLines)
INPUT 1 INPUT 2
Remarks
Vert.
Horiz.
(kHz)
(Hz)
70.1
70.1
85.1
60.0
66.7
72.8
75.0
85.0
100.4
120.4
60.0
60.0
56.0
60.0
72.0
75.0
85.0
99.8
120.0
74.6
60.0
60.0
70.0
75.0
74.9
85.0
100.6
119.4
60.0
72.0
75.0
75.1
66.0
76.0
640x400
720x400
31.5
31.5
37.9
31.5
35.0
37.9
37.5
43.3
51.1
61.3
31.0
31.7
35.2
37.9
48.1
46.9
53.7
63.0
75.7
49.7
48.4
49.7
56.5
60.0
60.2
68.7
80.5
95.6
53.7
64.9
67.5
68.5
61.8
71.7
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
√
√
√
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
√
√
√
√
–
√
√
√
√
√
√
–
√
√
Apple® Macintosh® 13”
640x480
I/O DATA
I/O DATA
848x480
852x480
I/O DATA
800x600
832x624
I/O DATA
I/O DATA
Apple Macintosh 16”
1024x768
Apple Macintosh 19”
I/O DATA
1152x864
1152x870
1152x900
Apple Macintosh 21”
Sun Microsystems LO
Sun Microsystems HI
70
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2. Computer/Video Signal Compatibility Chart (continued)
Refresh Rate
Input
Resolution
(DotsxLines)
INPUT 1 INPUT 2
Remarks
Vert.
Horiz.
(kHz)
(Hz)
56.0
60.0
70.0
60.0
60.0
60.0
85.0
60.0
60.0
71.2
72.0
75.0
76.1
85.0
100.1
60.0
60.0
59.9
60.0
74.9
75.0
85.0
60.0
60.0
65.0
70.0
75.0
85.0
60.0
60.0
60.0
45.1
47.8
56.1
49.7
53.1
60.0
85.9
64.0
64.6
75.1
78.1
80.0
81.1
91.2
108.5
47.7
47.7
48.3
65.3
82.3
82.3
93.9
56.0
75.0
81.3
87.5
93.8
106.3
65.3
74.6
74.0
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
√
√
√
√
–
–
√
√
–
–
–
–
√
–
√
1280x768
1280x800
1280x854
CVT
PC
1280x960
Workstation (SGI)
Workstation (EWS4800)
Workstation (EWS4800)
Workstation (HP)
1280x1024
Workstation (SUN)
I/O DATA
1360x765
1360x768
1376x768
I/O DATA
I/O DATA
1400x1050
1440x900
Apple Macintosh 17”
1600x1200
1680x1050
1920x1200
CVT
CVT
1920x1200RB
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
72
Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL NUMBER
RUMA-011205
rev 11-29-06 v3.0
Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300
Download from Www.Somanuals.com. All Manuals Search And Download.
|