Sanyo Projection Television 1AA6P1P1756 User Guide

Rear Projection Display  
Installation Manual  
REQUEST A SALES DEALER FOR INSTALLATION  
Please read all instructions below and install this system properly.  
Please read "SAFETY PRECAUTIONS" and "IMPORTANT SAFETY INSTRUCTIONS" on  
OWNER'S MANUAL to install and place this system.  
This system is supplied in 3 packages and they need to be installed. Please make sure all the  
parts are included. If any part is missing, or if you have questions, contact a sales dealer.  
Install the system following steps.  
1. CHECK CONTENTS IN PACKAGES  
2. ASSEMBLE BOTTOM CABINET  
3. JOINT TOP AND BOTTOM CABINETS  
4. SETUP PROJECTION MIRROR  
5. ADJUST PROJECTION MIRROR  
6. ASSEMBLE STORAGE SPACES  
7. LOCK CABINET  
THIS SYSTEM MUST BE INSTALLED BY 2 OR MORE PEOPLE  
CAUTION  
WHEN INSTALLING THIS SYSTEM, BE CAREFUL NOT TO DAMAGE THE PROJECTION  
SCREEN. AND NEVER TOUCH THE SURFACE OF THE PROJECTION SCREEN AND  
THE PROJECTION MIRROR DIRECTLY. THEY MAY EFFECT THE PROJECTION IMAGE  
QUALITY.  
BE CAREFUL NOT TO DROP ANY PART OR TOOL LIKE SCREW INTO THE SYSTEM. IF  
IT SHOULD, CONTACT A SERVICE.  
EXCEPT WHEN ADJUSTING THE PROJECTION MIRROR, NEVER TURN THE SYSTEM  
ON UNTIL THE INSTALLATION IS FINISHED. IT MAY CAUSE ELECTRICAL SHOCK OR  
FIRE HAZARD.  
710-00792-1  
1AA6P1P1756-- (M8EA)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLE BOTTOM CABINET  
2
Cover Plates  
(2 pcs)  
Joint Bolts (4 pcs)  
Remove Joint Bolts and Cover Plates  
1
Remove the 4 Joint Bolts on the Bottom Cabinet.  
Keep these bolts for later use. They are necessary  
for joint the Top and Bottom Cabinets.  
Remove the 2 Cover Plates on the top of the  
Bottom Cabinet. Keep the Cover Plates for later  
use. Replace those plates, when the appliance  
needs to be transported.  
Joint Bolts  
(4 pcs)  
Install Center Panel  
2
Install the Center Panel to the Bottom Cabinet. Be  
sure to meet the Center Panel and the Bottom  
Cabinet at the upper part first, and insert the 6 legs  
of Center Panel to the holes of the Bottom Cabinet.  
Be sure to set the Center Panel securely.  
Hole Leg  
Center Panel  
Meet the Center Panel and the Bottom  
Cabinet at the upper part first and  
push in the Panel securely.  
Remove Protection Pads  
3
There are the 5 Protection Pads inside of the  
Bottom Cabinet for protection against shock or  
vibration. Remove the 4 Pads supporting at the  
upper side of the Bottom Cabinet first. And then,  
remove the pad(A) supporting at the lower side of  
the projector. When removing the pad(A), pull  
downward first and remove the pad.  
Protection Pads (5 pcs)  
CAUTION  
WHEN REMOVING THE PROTECTION  
PADS, BE CAREFUL NOT TO BROKE THE  
WIRING INSIDE OF THE BOTTOM  
CABINET.  
BE SURE TO REMOVE ALL THE  
PROTECTION PADS INSIDE OF THE  
CABINET. AND BE CAREFUL NOT TO  
LEAVE ANY PAD OR FRAGMENT IN THE  
CABINET. IT MAY RESULT IN FIRE  
HAZARDS.  
Projector  
The back side of  
the Bottom Cabinet.  
Pad(A)  
Pull the pad(A) to  
downward first and  
remove the pad.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
J0INT TOP AND BOTTOM CABINETS  
3
Joint Top and Bottom Cabinets  
1
Screws (14 pcs)  
Lift the Top Cabinet and put it on the Bottom  
Cabinet. When setting the Top Cabinet, be sure  
the frame of the Bottom Cabinet is fitted into the  
frame of the Top Cabinet completely.  
Top  
Cabinet  
CAUTION  
THE TOP CABINET OF THIS PROJECTOR  
HAS ITS GRAVITY AT THE SCREEN SIDE.  
WHEN LIFTING THE TOP CABINET, BE  
CAREFUL NOT TO DROP.  
Bottom  
Cabinet  
Remove Back Cover  
2
Remove the 14 Screws and the Back Cover. Keep  
the screws and Back Cover. All the installations are  
finished, all those parts should be replaced.  
Top  
Cabinet  
Be sure the frame of  
the Bottom Cabinet  
is fitted into the  
frame of the Top  
Cabinet completely.  
Remove Cover Plate  
3
Remove the Cover Plate on the lower part of the  
Top Cabinet. Keep the Cover Plate for later use.  
Replace this plate when the appliance need to be  
transported.  
Frame  
Bottom  
Cabinet  
Fix the Cabinets  
4
Joint the Top and the Bottom Cabinets with the 4  
Joint Bolts securely.  
Joint Bolts  
(4 pcs)  
Joint Bolts  
(4 pcs)  
CAUTION  
BE SURE TO FIX THE CABINETS WITH  
JOINT BOLTS. IF THE TOP AND THE  
BOTTOM CABINETS ARE NOT FIXED  
PROPERLY, THE TOP CABINET MAY  
BE DROPPED OR FALL DOWN.  
Cover Plate  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETUP PROJECTION MIRROR  
4
Preparation  
1
Projection Mirror  
Remove the 4 Protection Pads inside of the Top  
Cabinet and remove the 2 Fixing Bands (right and  
left) of the Projection Mirror.  
Fixing Bands  
CAUTION  
NEVER TOUCH THE PROJECTION  
MIRROR DIRECTLY. IT MAY EFFECT THE  
PROJECTION IMAGE QUALITY. MOVE  
THE MIRROR BY HOLDING THE MIRROR  
HANDLE.  
Protection Pads (4pcs)  
BE SURE TO REMOVE ALL THE  
PROTECTION PADS FROM THE CABINET.  
Projection Mirror  
Fixing  
Bands  
(2 pcs)  
Set Mirror Arms  
2
3
Remove the 8 Screws(A) of the Mirror Arms. Lift  
the Projection Mirror and raise the Mirror Arms  
backward.  
Loosen the Screws(B) on the end of the Mirror  
Arms. Put the Mirror Holder between the Adjusting  
Nut and the Washer at each side of the Mirror. And  
then fix the Mirror Holders on the Mirror Arms with  
the Screws(B) temporary.  
Mirror Handle  
Screws(A)  
(4 pcs X 2)  
Mirror Arm  
Fix Projection Mirror  
Screw(B)  
Fix the Mirror Arms on the Cabinet with the  
Screws(A). Fix the Projection Mirror to the end of  
the Mirror Arms with the Screws(B) securely.  
Mirror Arm  
Screws(A)  
(4 pcs X 2)  
Adjusting Nut  
Screw(B)  
Mirror Holder  
Washer  
Mirror Arm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADJUST PROJECTION MIRROR  
5
When the figure of the projection image does not match the Projection Screen, adjust the Projection  
Mirror. If the figure fits the Projection Screen precisely, skip the steps 2, 3 and 4 and replace the Back  
Cover.  
Check Projection Image  
1
Connect the projector to the AC outlet, and turn the  
projector on. Connect the video output equipment  
to the projector. Project the image of cross-hatch or  
circles to check whether the picutre is displayed  
fully on the Projection Screen and is not distorted.  
(Refer to the Owner's Manual for operation.)  
If the figure is distorted, adjust the Projection Mirror  
following the steps 2 to 4 below.  
Screw(B)  
Mirror Holder  
If the picture is displayed properly, adjustment  
of the Mirror is not required. Skip the steps  
below and replace the back cover.  
Lower the  
Mirror Holder.  
Lift the Mirror  
Holder.  
Adjust Projection Mirror  
2
Adjust the Projection Mirror by turning the Adjusting  
Nuts. Move the Projection Mirror up or down by  
turning the Adjusting Nuts on the both sides of the  
Projection Mirror. Adjust Screw(B) if it required.  
Refer to the figure on the right for the image  
movement with the Adjusting Nut.  
Mirror Arm  
Adjusting Nut  
Turn Adjusting Nuts to adjust  
the screen image.  
Fix Projection Mirror  
3
4
Fix the Projection Mirror where the picture is  
displayed properly. Fix the Screw(B) securely.  
When fixing the Screw(B) the figure may be  
distorted again. When it should happen, readjust  
the Mirror following the steps 2 to 4.  
When turning the  
Adjusting Nuts on both  
sides to the right, the  
lower part of the image  
becomes narrow.  
Turn the projector off  
When turning the  
Adjusting Nuts on both  
sides to the left, the  
lower part of the image  
is stretched.  
Turn off the projector and disconnect it from the AC  
outlet.  
CAUTION  
DO NOT STARE DIRECTLY INTO THE  
LENS. EYE DAMAGE COULD RESULT.  
WHEN ADJUSTING THE MIRROR, NEVER  
TOUCH THE PARTS EXCEPT THE  
When turning the  
Adjusting Nuts on one  
side to the left or the  
right, one side of the  
lower part of the figure  
is  
shortened  
or  
MIRROR.  
IT MAY RESULT IN  
stretched.  
ELECTRICAL SHOCK.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLE STORAGE SPACES  
6
Screws (14 pcs)  
Replace Back Cover  
1
Replace the Back Cover to the Top Cabinet. Turn  
the Back Cover over, and fix the cover in the  
reverse to the initial position.  
Back Cover  
Install Glass Doors  
2
Holder Cover  
1. Remove the Hinge Covers by removing the 2  
screws of each Hinge.  
2. Hold the Glass Doors between the Glass Hinges  
and the Hinge Covers. Install the Glass Doors so  
that the side with the Holder Magnet is matched  
to the magnet inside of the Storage Spaces. Do  
not install the Glass Doors in the reverse.  
Tighten the screws and fix the Glass Doors.  
Screws  
(2pcs x 4)  
Holder Magnet  
Glass Door  
Adjustments of Doors  
3
1. When adjusting the position of the Glass Doors,  
loose the Screws(A) and move the Glass Doors  
with the Hinges to the arrow direction until the  
surface of the door matches to the surface of the  
Cabinet Front.  
Screw(A)  
2. When adjusting the tilt of the Glass Doors, adjust  
the Screws(B) (lower and upper) and move the  
Glass Doors.  
Screw(B)  
Shelves' Pins  
(4 pcs X 4)  
Install Compartment Shelves  
4
IInsert the Shelves' Pins into appropreate position  
of the walls of Storage Spaces. Install the  
Compartment Shelves in Storage Spaces.  
Compartment  
Shelves (4 pcs)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCK CABINET  
7
Lock the Cabinet  
1
Turn Lock Bolts to the direction indicated on the  
figure to lock the cabinet on the floor. Make sure  
that all the Casters are slightly raised from the floor.  
The tilt of Cabinet can be also adjusted with these  
Lock Bolts.  
Lock Bolt  
Lifting the  
Letting the  
cabinet down to  
move it.  
cabinet up to  
settle it.  
CAUTION  
BE SURE TO LOCK THE CABINET WITH  
LOCK BOLTS PROPERLY. IF THE  
CABINET IS NOT LOCKED, CABINET IS  
UNSTABLE AND MAY FALL DOWN.  
Cabinet Dimensions ( W x H x D ) : 1532 mm (60.3") x 1968mm (77.5" ) x 747mm (29.4" )  
Net Weight : 145kg (319.7lbs )  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Raymarine Two Way Radio Ray215 User Guide
ReliOn Blood Pressure Monitor HEM 780REL User Guide
Ricoh Digital Camera RDC 2 User Guide
Rolls Music Mixer MX442 User Guide
Royal Consumer Information Products Toaster Super Hot Toater User Guide
Samsung CRT Television TXL 2791F User Guide
Sanyo Air Conditioner CH0921 User Guide
Sears Lawn Mower 917257720 User Guide
Sears Saw 13728463 User Guide
SECO LARM USA Security Camera EV 1324C12 NTSC User Guide