TXL2791F
TXM2790F
TXM3292F
COLOR TELEVISION
.............
Ow ner’s
Instructions
AA68-01698B-00(ENG)
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning! Im portant
Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside. It is
dangerous to make any kind of contact with any inside part of
this product.
This symbol alerts you that important literature concerning
operation and maintenance has been included with this product.
Note to CATV system installer: This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of
Canadian Electrical Code, Part I), that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building as close to the point of cable entry as practical.
Caution: FCC/CSA regulations state that any unauthorized changes or modifica-
tions to this equipment may void the user’s authority to operate it.
Caution: To prevent electric shock, match the wide blade of plug to the wide slot,
and fully insert the plug.
Attention: pour eviter les chocs electriques, introduire la lame le plus large de la
fiche dans la borne correspondante de la prise et pousser jusqu’au fond.
Important: One Federal Court has held that unauthorized recording of
copyrighted TV programs is an infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized
recording in whole or in part may be in violation of these rights.
To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.
As an ENERGY STAR Partner,
Samsung Electronics America, Inc. has determined that this product or product
model meets the ENERGY STAR guidelines for energy efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank You for Choosing Sam sung
Thank you for choosing Samsung! Your new Samsung TV represents the latest in television
technology. We designed it with easy-to-use on-screen menus and closed captioning capabili-
ties, making it one of the best products in its class. We are proud to offer you a product that
will provide convenient, dependable service and enjoyment for years to come.
Im portant Safety Inform ation
Always be careful when using your TV receiver. To reduce the risk of fire, electrical shock,
and other injuries, keep these safety precautions in mind when installing, using, and
maintaining your machine.
• Read all safety and operating instructions before operating your TV.
• Keep the safety and operating instructions for future reference.
• Heed all warnings on the TV receiver and in the operating instructions.
• Follow all operating and use instructions.
• Unplug the TV receiver from the wall outlet before cleaning. Use a damp cloth; do not use
liquid or aerosol cleaners.
• Never add any attachments and/or equipment without approval of the manufacturer. Such
additions can increase the risk of fire, electric shock, or other personal injury.
• Do not use the TV receiver where contact with or immersion in water is a possibility, such as
near bath tubs, sinks, washing machines, swimming pools, etc.
• Do not place the TV on an unstable cart, stand, tripod, bracket, or
table where it can fall. A falling TV can cause serious injury to a
child or adult, and serious damage to the appliance. Use only with
a cart, stand, tripod, bracket, or table recommended by the manu-
facturer or sold with the TV. Follow the manufacturer’s instruc-
tions when mounting the unit, and use a mounting accessory rec-
ommended by the manufacturer. Move the TV and cart with care.
Quick stops, excessive force, and uneven surfaces can make the
unit and cart unsteady and likely to overturn.
• Provide ventilation for the TV receiver. The unit is designed with
slots in the cabinet for ventilation to protect it from overheating. Do not block these openings
with any object, and do not place the TV receiver on a bed, sofa, rug, or other similar sur-
face. Do not place it near a radiator or heat register. If you place the TV receiver on a rack or
bookcase, ensure that there is adequate ventilation and that you’ve followed the manufactur-
er’s instructions for mounting.
• Operate your TV receiver only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your appliance dealer
or local power company.
• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized
alternating current line plug having one blade wider than the other. This plug will fit into the
power outlet only one way. If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.
SAFETY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
• Protect the power cord. Power supply cords should be routed so that they won’t be walked on
or pinched by objects placed on or against them. Pay particular attention to cords at plugs, con-
venience receptacles, and the point where they exit from the unit.
• Unplug the TV from the wall outlet and disconnect the antenna or cable system during a light-
ning storm or when left unattended and unused for long periods of time. This will prevent dam-
age to the unit due to lightning and power-line surges.
• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of
overhead power lines or other electric light or power circuits or where it can fall into such
power lines or circuits. When installing an outside antenna system, be extremely careful to keep
from touching the power lines or circuits. Contact with such lines can be fatal.
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric
shock.
• Do not insert anything through the openings in the unit, where they can touch dangerous volt-
age points or damage parts. Never spill liquid of any kind on the TV.
• Ground outdoor antennas. If an outside antenna or cable
EXAMPLE OF
ANTENNA GROUNDING
system is connected to the TV, be sure the antenna or
ANTENNA
LEAD IN WIRE
cable system is grounded so as to provide some
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
protection against voltage surges and built-up static
charges. Section 810 of the National Electrical Code,
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
ANSI/NFPA No.70-1984, provides information about
proper grounding of the mast and supporting structure,
GROUND CLAMPS
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
discharge unit, connection to grounding electrodes, and
NEC — NATIONAL ELECTRICAL CODE
requirements for the grounding electrode.
• Do not attempt to service the TV yourself. Refer all servicing to qualified service personnel.
Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
- when the power-supply cord or plug is damaged
- if liquid has been spilled on the unit or if objects have fallen into the unit
- if the TV has been exposed to rain or water
- if the TV does not operate normally by following the operating instructions
- if the TV has been dropped or the cabinet has been damaged
- when the TV exhibits a distinct change in performance
• If you make adjustments yourself, adjust only those controls that are covered by the operating
instructions. Adjusting other controls may result in damage and will often require extensive
work by a qualified technician to restore the TV to normal.
• When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in additional damage to the unit.
• Upon completion of any service or repairs to this TV, ask the service technician to
perform safety checks to determine that the TV is in a safe operating condition.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference that may cause undesired operation.
This television receiver provides display of television closed captioning in accordance with
§15.119 of the FCC rules.
2
SAFETY
Download from Www.Somanuals.com. All Manuals Search And Download.
CO NTENTS
Chapter 1: Your New TV . . . . . . . . . . . . . . .1.1
List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1
Familiarizing Yourself with The TV. . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2
Front/Side Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5
Chapter 2: Installation . . . . . . . . . . . . . . . . 2.1
Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . 2.1
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . 2.1
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . 2.2
Separate VHF and UHF Antennas. . . . . . . . . . . . . . . . . . . . 2.2
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Connecting to a Cable Box that Descrambles
All Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Connecting to a Cable Box that Descrambles
some Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4
Connecting an S-VHS VCR. . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Connecting a Second VCR to Record from the TV . . . . . . . 2.7
Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7
Connecting a Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8
Installing Batteries in the Remote Control. . . . . . . . . . . . . . . . . . . . . 2.9
Chapter 3: Operation . . . . . . . . . . . . . . . . . . 3.1
Turning the TV On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
Viewing the Menus and On-Screen Displays. . . . . . . . . . . . . . . . . . . 3.3
Viewing the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3
Selecting a Menu Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4
Memorizing the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5
Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . 3.5
Storing Channels in Memory (Automatic Method) . . . . . . . 3.6
Adding and Erasing Channels (Manual Method) . . . . . . . . 3.7
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using the Channel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Directly Accessing Channels. . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using the PRE-CH Button to select the Previous Channel. . 3.8
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Using Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8
Labeling the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10
Option 1: Setting the Clock Manually . . . . . . . . . . . . . . . . 3.10
Option 2: Using the Local PBS Channel to
Automatically Set the TV Clock . . . . . . . . . . . . . . . . . . . . . 3.11
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14
Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15
Using Automatic Sound Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16
Setting The On/Off Melody. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.17
Viewing a VCR or Camcorder Tape. . . . . . . . . . . . . . . . . . . . . . . . . . 3.18
CONTENTS
CONTENTS
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CO NTENTS
Chapter 4: Special Features . . . . . . . . . . . . 4.1
Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1
Setting Up Your Remote Control to Operate Your VCR. . . . 4.1
Setting Up Your Remote Control to
Operate Your Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3
Fine Tuning Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Digital Noise Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5
Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
Using the R.Surf Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Setting the Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Sound Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.11
Choosing a Multi-Channel Sound (MTS) Soundtrack. . . . . 4.11
Extra sound settings
(Turbo Sound, Surround, or Auto Volume) . . . . . . . . . . . . 4.12
Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Using the V-Chip (Only USA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.14
Setting Up Your Personal ID Number (PIN) . . . . . . . . . . . . 4.14
How to Enable/Disable the V-Chip . . . . . . . . . . . . . . . . . . . 4.15
How to Set up Restrictions Using the “TV guidelines” . . . . 4.15
How to Set up Restrictions using the MPAA Ratings:
G, PG, PG-13, R, NC-17, X . . . . . . . . . . . . . . . . . . . . . . . . 4.17
How to Reset the TV after the V-Chip Blocks
a Channel (“Emergency Escape”) . . . . . . . . . . . . . . . . . . . . 4.18
Chapter 5: Troubleshooting . . . . . . . . . . . . 5.1
Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Cleaning and Maintaining Your TV. . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . A.1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1
2
CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r O n e
YO UR NEW TV
List of Features
Your TV was designed with the latest technology. This TV is a high-performance unit that
includes the following special features:
• Easy-to-use remote control
• Easy-to-use on-screen menu system
• Automatic timer to turn the TV on and off
• Adjustable picture and sound settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Built-in, dual channel speakers
• A special sleep timer
• Headphone jack for private listening
• 16:9 letter box format available depending upon source
CHAPTER ONE: YOUR NEW TV 1.1
Download from Www.Somanuals.com. All Manuals Search And Download.
YO UR NEW TV
Fam iliarizing Yourself w ith The TV
Front Panel Buttons
The buttons on the front panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.
For model TXL2791F
For model TXM2790F
For model TXM3292F
Œ
´
TV/ VIDEO (TXM3292F)
Press to change between viewing TV programs
and signals from other components.
ˆ
Ø
Rem ote Control Sensor
Aim the remote control towards this spot on the
TV.
MENU
Press to see an on-screen menu of your TV's fea-
tures.
POWER & TIMER indicator
When the TV is turned on, the POWER & TIMER
indicator blinks ten times. This indicator illumi-
nates when the TIMER mode is set to the “On”
position after setting the clock and either the On
timer or Off timer, with the remote control.
Even if the power is turned off, this indicator
stays lit. (Clock must be set before using this
function.)
ˇ
¨
VOL – , + (Volum e)
Press to increase or decrease the
volume. Also used to select items on the on-
screen menu.
CH M and CH MM(Channel)
Press to change channels. Also press to highlight
various items on the on-screen menu.
∏
POWER
Press to turn the TV on and off.
1.2
CHAPTER ONE: YOUR NEW TV
Download from Www.Somanuals.com. All Manuals Search And Download.
YO UR NEW TV
Front/ Side Panel J acks
You can use the front/Side panel jacks to connect an A/V component that is used only
occasionally, such as a camcorder or video game. (For information on connecting equip-
ment, see pages 2.1 – 2.8.)
For model TXM2790F
For model TXL2791F For model TXM3292F
Œ
´
AUDIO INPUTS
Used to connect the audio signals from a cam-
corder or video game.
ˇ
S-VIDEO INPUT jack
(TXM3292F)
Used to connect an S-Video signal from a cam-
corder or a video game.
VIDEO INPUT
Used to connect a video signal from a camcorder
or a video game.
¨
HEADPHONE J ACK
Connect a set of external headphones to this jack
for private listening.
CHAPTER ONE: YOUR NEW TV 1.3
Download from Www.Somanuals.com. All Manuals Search And Download.
YO UR NEW TV
Rear Panel J acks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a laserdisc player.
Because there are two sets of input jacks, you can connect two different A/V components
(i.e., a VCR and a laserdisc, 2 VCRs, etc.)
For more information on connecting equipment, see pages 2.1 – 2.8.
Œ
´
VIDEO INPUT jack
Video signals from VCRs, DVD
players and similar devices.
¨
ˆ
Ø
SUPER VIDEO INPUT jack
(For m odels TXL2791F/
TXM3292F)
S-Video signal from an S-VHS VCR or DVD player.
AUDIO INPUTS(INPUT1 and 2)/
DVD AUDIO INPUTS(INPUT 2)
Audio signals from VCRs, DVD players and similar
devices.
DVD VIDEO INPUT jacks
Connect video from a DVD player.
Note: Only black and white signals are output
from a monitor in DVD mode.
Use these jacks to connect the audio signals
from a DVD player when using the DVD video
input jacks. When not using the DVD jacks, these
audio jacks function as audio for Video 2 or S-
VIDEO).
VHF/ UHF
Connect to an antenna or to a cable TV system.
ˇ
AUDIO-VIDEO MONITOR
OUTPUT jacks
These audio-video signals are identical to A/V
signals being displayed on the big screen.
(Typically used as the input signals for a record-
ing VCR.)
1.4
CHAPTER ONE: YOUR NEW TV
Download from Www.Somanuals.com. All Manuals Search And Download.
YO UR NEW TV
Rem ote Control
You can use the remote control up to about 23 feet from the TV. When using the remote,
always point it directly at the TV.
You can also use your remote control to operate your VCR and cable box. See page 4.1 for
details.
Note: The buttons that are not described below do not function.
Œ
´
POWER
Turns the TV on and off.
˝ TV
Press to use your remote control
to operate your TV.
Num ber buttons
Press to select channels directly
on the TV.
VCR
Press to use your remote control
to operate your VCR.
+100
Press to select channels over 100.
For example, to select channel
121, press “+100,” then press “2”
and “1.”
CABLE
Press to use your remote control
to operate a cable box.
SET
ˇ
¨
P.SIZE
Press to change the screen size.
Use this button when you are set-
ting up your remote control to
operate your VCR or cable box.
R.SURF
Press the R.SURF button to auto-
matically return to a preferred
channel after a user-preset time
delay.
Ô
PRE-CH
Tunes to the previous channel.
MTS (Multichannel
Television Stereo)
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
ˆ
Ø
∏
”
SLEEP
Press to select a preset time inter-
val for automatic shutoff.
TURBO
Press to turn the TURBO sound On
or Off.
Ò
Ú
DISPLAY
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
MUTE
Press to temporarily cut off the
sound.
VOL -, VOL
+
Press to increase or decrease the
volume. (Also used to make selec-
tions on the on-screen menus.)
CHꢀꢀand CHꢀ
(Channel Up/ Dow n)
Press CHꢀ or CHꢀ to change
channels. (Also used to highlight
selections on the on-screen
menus.)
Æ
ı
MENU
Displays the main on-screen
menu.
TV/ VIDEO
’
P.STD
Press to display all of the
available video sources (i.e.,
Antenna/cable, VCR).
Adjust the TV picture by selecting
one of the preset factory settings
(or select your personal, cus-
tomized picture settings).
For models TXL2791F/TXM3292F
CHAPTER ONE: YOUR NEW TV 1.5
Download from Www.Somanuals.com. All Manuals Search And Download.
YO UR NEW TV
Rem ote Control
˜
VCR Controls
•
REW (Rew ind)
Press to rewind a tape in your
VCR.
•
STOP
Press this button to stop a tape
during play, record, rewind or
fast forward. If the button is
pressed during Full-Automatic
play, the function will be can-
celled.
•
•
•
PLAY
Press the PLAY button to play
back prerecorded tapes.
F. F
Press to fast forward the tape in
your VCR.
PAUSE
Press to pause your VCR’s tape.
For models TXL2791F/TXM3292F
1.6
CHAPTER ONE: YOUR NEW TV
Download from Www.Somanuals.com. All Manuals Search And Download.
YO UR NEW TV
Rem ote Control
Œ
´
POWER
Turns the TV on and off.
”
’
SLEEP
Press to select a preset time inter-
val for automatic shutoff.
Num ber buttons
Press to select channels directly
on the TV.
MTS (Multichannel
Television Stereo)
Press to choose stereo, mono or
Separate Audio Program (SAP
broadcast).
ˇ
+100
Press to select channels over 100.
For example, to select
channel 121, press “+100,” then
press “2” and “1.”
˝
V.CHIP(Only USA)
Press to set up and activate the
parental locks.
¨
ˆ
MUTE
Press to temporarily cut off
the sound.
Ô
PRE-CH
Tunes to the previous channel.
CHMMand CHM
(Channel Up/ Dow n)
Press CHM or CHM to change
channels. (Also used to highlight
selections on the on-screen
menus.)
DISPLAY
Press to see the time, channel,
etc., on-screen. Also press to exit
(quit) the menu system.
Ò
Ú
VOL -, VOL
+
Ø
∏
TV/ VIDEO
Press increase or decrease the
volume. (Also used to make selec-
tions on the on-screen menus.)
Press to display all of the
available video sources (i.e.,
Antenna/cable, VCR).
MENU
Displays the main on-screen
menu.
R.SURF
Press the R.SURF button to auto-
matically return to a preferred
channel after a user-preset time
delay.
For model TXM2790F
CHAPTER ONE: YOUR NEW TV 1.7
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Ch a p t e r Tw o
INSTALLATIO N
Connecting VHF and UHF Antennas
If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads,” below.
If your antenna has one lead that looks
like this, see “Antennas with 75-ohm
Round Leads,” on page 2.2.
If you have two antennas, see “Separate
VHF and UHF Antennas,” on page 2.2.
Antennas w ith 300-ohm Flat Tw in Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.
1
Place the wires from the
twin leads under the
screws on the 300-75 ohm
adaptor (not supplied).
Use a screwdriver to
tighten the screws.
2
Plug the adaptor into the
VHF/UHF terminal on the
bottom of the back panel.
2.1
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
Antennas w ith 75-ohm Round Leads
1
Plug the antenna lead into
the VHF/UHF
terminal on the bottom of
the back panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires an optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna
leads to the combiner.
2
Plug the combiner into the
VHF/UHF terminal on the
bottom of the rear panel.
Connecting Cable TV
To connect to a cable TV system, follow the instructions below.
Cable w ithout a Cable Box
Because this TV is
1
cable-ready, you do not need a
cable box to view unscrambled cable
channels.
Plug the incoming cable
into the VHF/UHF
antenna terminal on back
of the TV.
CHAPTER TWO: INSTALLATION
2.2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
Connecting to a Cable Box that Descram bles All Channels
This terminal might be labeled
“ANT OUT,” “VHF OUT,” or simply,
“OUT.”
1
Find the cable that is con-
nected to the ANTENNA
OUT terminal on your
cable box.
2
Connect the other end of
this cable to the VHF/UHF
antenna
terminal on the back of
the TV.
Connecting to a Cable Box that Descram bles Som e Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of
coaxial cable. (These items are available at most electronics stores.)
This terminal might be labeled
“ANT IN,” “VHF IN,” or simply,
“IN.”
1
Find and disconnect the
cable that is connected to
the ANTENNA IN
terminal on your
cable box.
2
Connect this cable to a
two-way splitter.
3
Connect a coaxial cable
between an OUTPUT ter-
minal on the splitter and
the IN terminal on the
cable box.
2.3
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
4
Connect a coaxial cable
between the ANTENNA
OUT terminal on the cable
box and the B–IN terminal
on the A/B switch.
5
Connect another cable
between the other OUT
terminal on the splitter
and the A–IN terminal on
the RF (A/B) switch.
6
Connect the last coaxial
cable between the OUT
terminal on the RF (A/B)
switch and the VHF/UHF
terminal on the rear of the
TV.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing.
Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B
switch to “B,” you will need to tune your TV to the cable box’s output channel, which is usu-
ally channel 3 or 4.)
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable
TV system (according to the instructions on pages 2.1-2.3). Skip step 1 if you have not yet
connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the back of
the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal on
the back of the VCR.
CHAPTER TWO: INSTALLATION
2.4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
3
Connect a coaxial cable
between the ANTENNA
OUT terminal on the VCR
and the antenna
terminal on the TV.
A coaxial cable is usually included with a VCR. (If not, check your local electronics
store).
4
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the AUDIO jacks
on the TV.
If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook up
to the left and right audio input jacks of the TV. If your VCR is stereo, you must con-
nect two cables.
5
Connect a video cable
between the VIDEO OUT
jack on the VCR and the
VIDEO jack on the TV.
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
Note: This figure shows the Standard Connector-jack panel. The actual configuration on your
TV may be different, depending on the model.
2.5
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
Connecting an S-VHS VCR
(For m odels TXL2791F/ TXM3292F)
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
1
To begin, follow steps
1–3 in the previous
section to connect the
antenna or cable to your
VCR and your TV.
2
Connect a set of audio
cables between the
AUDIO OUT jacks on the
VCR and the 2 AUDIO
INPUT jacks on the TV.
Make sure the jacks you are using are underneath the number “2.”
3
Connect an S-video cable
between the S-VIDEO OUT
jack on the VCR and the
S-VIDEO INPUT jack on
the TV.
An S-video cable is usually included with an S-VHS VCR. (If not, check your local
electronics store.)
CHAPTER TWO: INSTALLATION
2.6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
Connecting a Second VCR to Record from the TV
Your TV can send out signals of its picture and sound to be recorded by a second VCR.
To do this, connect your second VCR as follows:
1
Connect a set of audio
cables between the
AUDIO OUT jacks on the
TV and the AUDIO IN
jacks on the VCR.
(The VCR input jacks might be either on the front or on back of the VCR.)
2
Connect a video cable
between the VIDEO OUT
jack on the TV and the
VIDEO IN jack on the VCR.
Refer to your VCR’s instructions for more information about how to record using this kind
of connection.
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the
AUDIO INPUT 2 jacks on
the TV and the AUDIO
OUT jacks on the DVD
player.
2
Connect a video cable
between the DVD-IN (Y,
Pb, Pr) jacks on the TV
and the DVD-OUT (Y, Pb,
Pr) jacks on the DVD
player.
Note: For an explanation
of Component video, see
your DVD player's
owner's manual.
2.7
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
Connecting a Cam corder
The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow
you to view the camcorder tapes without using a VCR. (Also see “Viewing a VCR or
Camcorder Tape” on page 3.18)
1
Locate the A/V output
jacks on the camcorder.
They are usually found on
the side or back of the
camcorder.
2
Connect an audio cable
between the AUDIO OUT-
PUT jack on the cam-
corder and the AUDIO
terminals on the side of
the TV.
3
Connect a video cable
between the VIDEO OUT-
PUT jack on the cam-
corder and the VIDEO ter-
minal on the side of the
TV.
The audio-video cables shown here are usually included with a Camcorder. (If not, check
your local electronics store.) If your camcorder is stereo, you need to connect a set of two
cables.
Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV
may be different, depending on the model.
CHAPTER TWO: INSTALLATION
2.8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIO N
Installing Batteries in the Rem ote Control
1
Slide the cover out com-
pletely.
Make sure to match the “+” and
2
“–” ends of the batteries with the
Install two AA size
batteries.
diagram inside the compartment.
Remove the batteries and store
them in a cool, dry place if you won’t
be using the remote control for a
long time.
3
Replace the cover.
The remote control can be used up
to about 23 feet from the TV.
(Assuming typical TV usage, the
Batteries last for about one year.)
2.9
CHAPTER TWO: INSTALLATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a pterTh r e e
OPERATIO N
Turning the TV On and Off
Press the POWER button.
You can also use the POWER button on the front panel.
Plug & Play Feature
When the TV is initially powered On, five basic customer settings proceed automatically
and subsequently: Setting the language, Video signal source, Ant. input check, Auto pro-
gram and Clock.
1
Press the POWER button
on the remote control.
The message “Plug &
Play” is displayed.
It flickers for a little while
and then the “Language”
menu is automatically dis-
played.
2
Press the VOL+ or VOL-
button to select the
desired language.
Press the MENU button to
enter the language, and
then the “Channel” menu
is automatically displayed.
3
Press the VOL+ or VOL-
button to select the
desired video signal
source.
Press the MENU button to
enter the video signal
source, and then the “Ant.
Input check” is automati-
cally displayed.
continued...
CHAPTER THREE: TV OPERATION
3.1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
4
Make sure that the anten-
na is connected to the TV.
And then Press the VOL+
or VOL- button to activate
"Auto Program" or press
the MENU button to skip.
(refer to “Auto program”
on page 3.6.)
5
Press the VOL+ or VOL-
button to move to the hour
or minute. Set the hour or
minute by pressing the
CHꢀ or CHꢀꢀbutton.
(refer to “Setting the
clock” on page 3.10.)
6
When you have finished,
press the MENU button.
The message “Enjoy your
watching” is displayed.
7
If you want to reset this
feature
(1)Press the MENU but-
ton.
(2) Press the CHꢀ button
three times to select
the Function menu and
press the VOL+ button.
(3)Press the CHꢀ button
to select Plug & Play
and press the VOL+
button.
The message “Plug &
Play” is displayed.
Note: Plug & Play feature doesn’t work when the V-chip
on or when in the A/V mode.
3.2
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
View ing the Menus and On-Screen Displays
View ing the Menus
The on-screen menus disappear
from the screen after thirty seconds.
1
With the power on, press
the MENU button.
The main menu appears
on the screen. Its left side
has four icons: Picture,
Sound, Channel, and
Function.
You can also use the MENU,
CHANNEL, and VOLUME buttons
on the control panel of the TV to
make selections.
2
Use the CHꢀ and CHꢀ buttons to highlight one of the 4 icons.
Then press the VOL+ button to access the icon’s sub-menu.
3
Press the MENU button to exit.
View ing the Display
The display identifies the current channel and the status
of certain audio-video settings.
The on-screen displays
1
disappear after ten seconds.
Press the DISPLAY
button on the remote con-
trol.
The on-screen display
shows any or all of the fol-
lowing: Active channel,
the channel label, video
source, the time, and the
time remaining on the
sleep timer.
(“*” indicates a channel
has been manually fine
tuned.)
CHAPTER THREE: TV OPERATION
3.3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Selecting a Menu Language
1
Press the MENU button to
display the menu.
Press the CH ꢀ button
three times to select
“Function.”
2
Press the VOL + button to
display the “Function”
menu.
3
Press the VOL + button to select the appropriate language:
English, Spanish, or French.
4
Press the MENU button twice to exit.
3.4
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Mem orizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH ꢀ and
CH ꢀ buttons to scan through the channels. This eliminates the need to change chan-
nels by entering the channel digits. There are three steps for memorizing channels:
selecting a broadcast source, memorizing the channels (automatic) and adding and
deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to the TV (i.e., an antenna or a cable system).
1
Press the MENU button to
display the menu.
2
Press the CH ꢀ button
two times to select
“Channel.”
3
Press the VOL + button.
The first line of the menu
is selected.
4
Repeatedly press the VOL
+ button to cycle through
these choices:
ANT (antenna) STD, HRC
or IRC (all cable TV).
Note: STD, HRC and IRC identify various types of cable TV
systems. Contact your local cable company to identify the type
of cable system that exists in your particular area.
At this point the signal source has been selected. Proceed to
“Storing Channels in Memory” (next page).
CHAPTER THREE: TV OPERATION
3.5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Storing Channels in Mem ory (Autom atic Method)
1
First, select the correct
signal source (ANT, STD,
HRC, IRC). See steps 1~4
on previous page.
Press the MENU button,
then press the CH ꢀꢀbut-
ton twice to select
“Channel.”
Press the VOL + button to
access the Channel sub-
menu.
2
Press the CH ꢀ button to
select “Auto program”.
The TV automatically cycles
through all of the available channels
and stores them in memory. This
takes about one to two minutes.
3
Press the VOL + button.
The TV will begin
memorizing all of the
available channels.
Press MENU at any time to interrupt
the memorization process and return
to the Channel menu.
4
After all the available
channels are stored, the
Auto program menu reap-
pears. Press the MENU
button twice to exit.
Note: Channel auto program does not function when the
V-chip is active.
3.6
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Adding and Erasing Channels (Manual Method)
1
Press the MENU button ,
then press the CH ꢀꢀbut-
ton twice to select
“Channel”.
Press the VOL+ button to
access the channel sub-
menu.
2
Press the CH ꢀꢀor CH ꢀ
button to select
“Add/Erase”.
Press the VOL+ button.
3
Press the VOL+ button.
Press the CH ꢀ/ꢀꢀbutton
or the number buttons to
select the channel you
want to add or erase.
Press the MENU button.
4
Press the CH ꢀꢀor CH ꢀ
button to select “Select”.
Press the VOL+ or VOL-
button to select “Added”
or “Erased”.
Press the MENU button
three times to exit.
CHAPTER THREE: TV OPERATION
3.7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Changing Channels
Using the Channel Buttons
1
Press the CH ꢀ or CH ꢀ button to change channels.
When you press CH ꢀ or CH ꢀ, the TV changes channels in sequence. You will
see all the channels that the TV has memorized. (The TV must have memorized
at least three channels.) You will not see channels that were either erased or not
memorized.
Directly Accessing Channels
Use the number buttons to quickly tune to any channel.
1
Press the number buttons to go directly to a channel.
For example, to select channel 27, press “2,” then “7.”
The TV will change channels when you press the
second number.
When you use the number buttons, you can directly select channels that were
either erased or not memorized.
To select a channel over 100, press the +100 button. (For channel 122, press
“+100,” then “2,” then “2.”)
To change to single-digit channels (0–9) faster, press “0” before the
single digit. (For channel “4,” press “0,” then “4.”)
Using the PRE-CH Button to select the Previous Channel
To quickly switch between two
1
channels that are far apart, tune to
one channel, then use the number
button to select the second channel.
Then, use the PRE-CH button to
quickly alternate between them.
Press the PRE-CH button.
The TV will switch to the last channel viewed.
Adjusting the Volum e
Press VOL + or – VOL to increase or decrease the volume.
Using Mute
At any time, you can temporarily cut off the sound using the Mute button.
1
Press the MUTE button and the sound cuts off.
The word “Mute” will appear in the lower-left corner of the
screen.
2
To turn mute off, press the MUTE button again, or simply press
either the VOL – or VOL + button.
3.8
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Labeling the Channels
Use this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”,
“PBS2”, CNN1”, etc.) A label consists of four fields, where each field is a letter, a num-
ber, “*”, or a blank. When the DISPLAY button is pressed, the channel label will appear
next to the channel number.
1
Press the CH ꢀ or CH ꢀꢀbutton
to tune to the channel that will
be labeled.
Note: You cannot select
2
“Labeling” in the A/V mode.
Press the MENU button to dis-
play the menu.
Press the CH ꢀꢀbutton twice to
select “Channel”.
Press the VOL + button.
3
Press the CH ꢀ button five
times to select “Labeling”.
Press the VOL + button to begin
labeling. The left-most field will
be highlighted.
(Each label has four fields. See
top paragraph.)
4
Press the CH ꢀ or CH ꢀ button
to select a letter, a number, “*”,
or a blank. (Pressing the CH ꢀ
button results in this sequence:
A,B,...Z,*, blank,0,1,...9).
5
Press the VOL+ button to switch
to the next field, which will be
highlighted. Select a second let-
ter or digit using the CH ꢀ and
CH ꢀꢀbuttons, as above.
Repeat the process to select the
last two digits.
Press the MENU button twice to set the label and clear the
menus from the screen.
CHAPTER THREE: TV OPERATION
3.9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Setting the Clock
Setting the clock is necessary in order to use the various timer features of the TV. Also,
you can check the time while watching the TV. (Just press Display.)
Option 1: Setting the Clock Manually
1
Press the MENU button to
display the on-screen
menu.
Press the CH ꢀ button
three times to select
“Function.”
Press the VOL + button.
2
Press the CH ꢀꢀbutton
three times to select Time
menu.
Press the VOL + button:
The Time menu will appear
on the screen, and “Clock”
will be highlighted.
When selecting the hours, be sure
to select the proper time of day (AM
or PM).
3
Press the VOL + button
again (the hours digits will
be highlighted).
You can change the hours by pressing
CH ꢀ or CH ꢀ repeatedly (or by
holding down either of these buttons).
Press the CH ꢀ or CH ꢀ
button repeatedly until the
correct hour appears.
After the hour is entered,
press the VOL + button. (at
this point the minutes dig-
its will be highlighted).
The time will appear every time
you press the DISPLAY button.
4
Press the CH ꢀ or CH ꢀ
button to select the cor-
rect minutes.
After selecting the correct
minutes, press the VOL +
button.
Press the MENU button
three times to exit.
3.10
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Option 2: Using the Local PBS Channel to Autom atically Set the
TV Clock
1
Press the MENU button to
display the menu.
Press the CH ꢀ button
three times to select
“Function.”
Press the VOL + button.
2
Press the CH ꢀ button
four times to select “Auto
clock set” menu.
Press the VOL + button.
3
Press the VOL + button to
select Auto clock set
“On”.
4
Press the CH ꢀ button to
select “PBS channel”.
While “PBS channel” is
selected, press the VOL +
button to activate the
channel-number field.
Press the CH ꢀ and CH ꢀ
button to select your local
PBS channel.
Press the MENU button.
continued...
CHAPTER THREE: TV OPERATION
3.11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
5
Press the CH ꢀ button to
select “Time zone”. While
“Time zone” is selected,
press either VOL+ or VOL-
button to change the Time
zone.
Sequence: ATL., EAST,
CEN., MTN., PAC., ALAS.,
HAW.
6
Press the CH ꢀ button to
select “DST”(Daylight
saving time). While “DST”
is selected, press the
VOL+ or VOL- button to
indicate “Yes” or “No”.
The clock is set.
Press the MENU button
three times to exit.
3.12
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Custom izing the Picture
You can use the on-screen menus to change the contrast, brightness, tint, color, and
sharpness according to personal preference. (Alternatively, you can use one of the
“automatic” settings. See next page.)
1
Press the MENU button to
display menu.
The customer can select
“Normal”, “Warm”, or “Cool” accord-
ing to personal preference.
2
Press the VOL – or VOL +
button repeatedly, until the
word “Custom” is selected.
(When Custom is highlight-
ed, the words “Adjust” will
appear on the screen.)
3
Press the CH ꢀꢀ button to
select “Adjust”, then
press the VOL+ button.
(The words Contrast,
Brightness, Sharpness,
Color, and Tint will appear
on the screen.)
Press the CH ꢀꢀor CH ꢀ
button to select a particu-
lar item.
After adjusting an item, the gauge
will automatically disappear (after
about 5 seconds).
4
Press the VOL – or VOL +
button to increase or
decrease the value of a
particular item. For exam-
ple, if you select
“Brightness,” pressing the
VOL + button increases it.
Press the MENU button
four times to exit.
CHAPTER THREE: TV OPERATION
3.13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Using Autom atic Picture Settings
Your Samsung TV has three automatic picture settings (“Standard”, “Natural”, and
“Mild”) that are preset at the factory. You can activate either Standard or Mild by pressing
P.Mode (or by making a selection from the menu). Or, you can select “Custom” which
automatically recalls your personalized picture settings.
1
Press the MENU button to
display the menu.
Press the VOL + button.
2
Press the VOL - or VOL +
button to select the
“Standard,” “Natural,”
“Mild,” or “Custom” pic-
ture setting.
•
•
•
Choose Standard for the standard factory settings.
Natural: Optimal indoor screen condition.
Choose Mild (“Mild Contrast”) when viewing the TV in low light, or when
playing video games.
•
Choose Custom if you want to adjust the settings accordings to personal
preference (see “Customizing the Picture, page 3.13).
3.14
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Custom izing the Sound
You can use the on-screen menus to adjust the bass, treble, and balance according to
individual preference. (Alternatively, you can use one of the “automatic” settings. See
next page.)
1
Press the MENU button to
display the menu.
Press the CH ꢀ button to
select the “Sound” menu.
2
Press the VOL - or VOL +
button repeatedly, until
the word “Custom” is
selected. (When Custom
is selected, the words
“Adjust” will appear on
the screen.
3
Press the CH ꢀ button to
select “Adjust”, then
press the VOL+ button.
(The words Bass, Treble,
and Balance will appear
on the screen.)
Press the CH ꢀ or CH ꢀ
button to select a particu-
lar item to be changed.
4
Press the VOL – or VOL +
button to increase or
decrease the value of a
particular item. For exam-
ple, if you select “Bass,”
pressing the VOL + button
increases it.
Press the MENU button
three times to exit.
CHAPTER THREE: TV OPERATION
3.15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Using Autom atic Sound Settings
Your TV has four automatic sound settings (“Standard,” “Music,” “Movie,” and “Speech”)
that are preset at the factory. You can activate any of them by making a selection from the
on-screen menu. Or, you can select “Custom,” which automatically recalls your personalized
sound settings.
1
Press the MENU button to
display the menu.
Press the CHꢀ button
once to select the
“Sound” menu.
2
Press the VOL - or VOL +
button repeatedly to
select the “Standard,”
“Music,” “Movie,”
“Speech” or “Custom”
sound settings.
•
•
•
•
•
Choose Standard for the standard factory settings.
Choose Music when watching music videos or concerts.
Choose Movies when watching movies.
Choose Speech when watching a show that is mostly dialogue (i.e., news).
Choose Custom to recall your personalized settings.
3.16
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
Setting The On/ Off Melody
You can hear clear melody sound when the TV is powered on or Off.
1
Press the MENU button to
display the menu.
Press the CH ꢀꢀbutton to
select the “Sound” menu.
2
Press the VOL - or VOL +
button repeatedly, until
the word “Custom” is
selected. (When Custom
is selected, the words
“Adjust” will appear on
the screen.
3
Press the CH ꢀꢀbutton to
select “Adjust”, then
press the VOL+ button.
4
Press the CH ꢀ button to
select “Melody”, then
press the VOL+ or VOL–
button to select “On” or
“Off”.
Press the MENU button
three times to exit.
CHAPTER THREE: TV OPERATION
3.17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIO N
View ing a VCR or Cam corder Tape
You must select the appropriate mode in order to view the VCR or
Camcorder signal on the TV.
1
Press the MENU button to
display the menu.
Press the CH ꢀ button
twice to select
“Channel”, then press the
VOL+ button.
2
Press the CH ꢀ button
twice to select “TV/AV”.
3
Press the VOL+ or VOL-
button.
You will switch between
viewing the signals com-
ing from equipment con-
nected to the TV’s A/V
jacks, and the TV signal.
3.18
CHAPTER THREE: TV OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r Fo u r
SPECIAL FEATURES
Custom izing Your Rem ote Control
(For m odels TXL2791F/ TXM3292F)
Your TV comes equipped with a “universal” remote control. In addition to
controlling the TV, the universal remote can also operate a VCR and a cable box (even if your
VCR and cable box are made by manufacturers other than Samsung).
Setting Up Your Rem ote Control to Operate Your VCR
1
Turn off your VCR.
2
On your Samsung remote control, press the SET button.
The remote control has three
“modes”: “TV,” “VCR”, and “Cable”
Press the “VCR” button to switch the
3
Press the VCR button on the top right of your remote control.
remote control to the “VCR” mode.
Make sure you enter both digits of
the code, even if the first digit is a “0.”
If more than one code listed, try the
first one.
4
Enter both digits of the VCR code listed on the next page for
your brand of VCR.
If your VCR does not turn on,
repeat steps 2, 3, and 4, but try one
of the other codes listed for the
brand of your particular VCR.
If no other codes are listed, try each
code, 000 through 72.
5
Press the POWER button on the remote control. Your VCR
should turn on. If your VCR turns on, your remote control is
now set correctly.
When your remote control is in
the “VCR” mode, the volume buttons
still control your TV’s volume.
6
Once your remote control is set up, press the VCR button
any time you want to use the remote to operate your VCR.
When your remote is in the “TV”
mode, the VCR control buttons (PLAY,
PAUSE, etc.) will still operate your
VCR.
CHAPTER FOUR: SPECIAL FEATURES
4.1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
VCR Codes
4.2
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Setting Up Your Rem ote Control to Operate Your Cable Box
1
Turn off your cable box.
2
On your Samsung remote control, press the SET button.
The remote control has three
“modes”: “TV,” “VCR,” and
“CABLE”.
3
Press the CABLE button on the top right of your remote
control.
Press the “CABLE” button to switch
the remote control to the “Cable”
mode.
Make sure you enter both digits
of the code, even if the first digit is a
“0.” (If more than one code listed,
try the first one.)
4
Enter both digits of the cable box code listed below for your
brand of cable box.
If your cable box does not turn
on, repeat steps 2, 3, and 4, but try
one of the other codes listed for your
particular brand of cable box. (If no
other codes are listed, try each cable
box code, 00 through 35.)
5
Press the POWER button. Your cable box should turn on. If your
cable box turns on, your remote control is now “set up” correct-
ly.
When your remote control is
in the “CABLE” mode, the volume
buttons still control your TV’s vol-
ume. Also, the VCR control buttons
(PLAY, PAUSE, etc.) will still operate
your VCR.
6
Once your remote control is set up, press the CABLE button
any time you want to use the remote to operate your cable
box.
Cable Box
Codes
CHAPTER FOUR: SPECIAL FEATURES
4.3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Fine Tuning Channels
Use fine tuning to manually adjust a particular channel for optional reception.
1
Select the appropriate
channel.
Press the MENU button to
display the menu.
Press the CH ▼ button
twice to select the
“Channel” menu.
2
Press the VOL+ button to
select Channel menu.
Press the CH ▼ button
three times to select “Fine
tune”.
After you adjust the fine tuning,
3
“*” will appear when you press DIS-
PLAY while watching this channel.
Press the VOL+ and VOL-
button to adjust the fine
tuning.
Press the MENU button to
resume normal viewing.
4
To store the fine tuning
setting in the TV’s memo-
ry, press the CH ▼▼button.
( “*” will appear).
To reset the fine tuning to
“oo”, press CH ▼.
4.4
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate the Digital
Noise Reduction feature to help reduce any static and ghosting that may appear on
the screen.
1
Press the MENU button to
display the menu.
Press the VOL + button to
select the “Picture” menu.
2
Press the CH ▼▼button
three times to select
"Digital NR."
Pressing VOL- or VOL+ will
alternate between “On” and “Off”.
3
Press the VOL + or VOL -
button to select Digital
NR “On”.
Press the MENU button
twice to exit.
CHAPTER FOUR: SPECIAL FEATURES
4.5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Tilt
Due to the Earth’s magnetic field there may be same minor image tilt depending on the
TV’s location. When this occurs, follow the steps below.
1
Press the MENU button to
display the menu.
Press the VOL + button to
select the Picture menu.
2
Press the CH ▼▼button
five times to select
“Setup.”
Press the VOL + button.
3
Press the VOL– or VOL+
buttons to adjust the Tilt.
Press the Menu button to
exit.
4.6
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Changing the Screen Size
1
Press the MENU button to
display the menu.
Press the VOL + button to
select the “Picture” menu.
2
Press the CH ▼ button
twice to select "Size."
3
Press the VOL + or VOL -
button repeatedly to
select “Normal”, “Zoom”,
or “Wide”
Press the MENU button
twice to exit.
•
•
•
Normal : Sets the picture to 4:3 normal mode. This is a standard TV screen size.
Zoom : Magnifies the size of the picture on-screen.
Wide : Sets the picture to 16:9 wide mode.
Note:
TXL2791F/TXM2790F: Normal ▼ Zoom ▼▼Wide.
TXM3292F: Normal ▼▼Wide.
CHAPTER FOUR: SPECIAL FEATURES
4.7
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Using the R.Surf Feature
This feature allows you to set the TV to return to a particular channel after a certain
amount of time. For example, you may be watching a channel when commercials
start. You can set the R.Surf to “5 minutes”, then switch channels. After 5 minutes,
the TV will return to the original channel. To use the R.Surf:
1
While you are watching
the channel to which you
want to return, press the
R.SURF button. The on-
screen display will read
“Surf off”.
2
Press the R.SURF button
again to set the timer in
thirty second intervals, up
to five minutes.
3
The time you set will begin counting down on the screen.
When the time runs out, the TV will return to the channel
you were watching when you set the timer.
4.8
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Setting the On/ Off Tim er
Before using the timer, you must
set the TV’s clock. (See “Setting the
Clock” on page 3.10).
1
Press the MENU button to
display the menu.
When any of the timers are set, the
“Timer” LED will illuminate (front
panel of TV.)
Press the CH ▼ button
three times to select
"Function" menu.
2
Press the VOL+ button to
select the “Function” sub-
menu.
Press the CH ▼ button
three times to select
"Time".
Press the VOL+ button.
When you set the hours, make
sure the correct time of day (AM or
PM) appears to the left of the hour.
3
Press the CH ▼ button to
select "On time".
Press the VOL+ button to
select the “On time”
hours.
(The hours digits will be
highlighted.)
Press the CH ▼ or CH ▼
button repeatedly to
select the appropriate
hours (i.e., the hour when
the TV will turn on.)
4
Press the VOL+ button to
select the “On time” min-
utes.
(The minutes digits will be
highlighted.)
Press the CH ▼ or CH ▼
button to select the appro-
priate minutes.
CHAPTER FOUR: SPECIAL FEATURES
4.9
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
To deactivate the “On time,”
select “Off” during this step.
5
Press the VOL + button to
select “On/Off.”
Press the CH ▼ (or CH ▼)
button to turn the on-
timer “On.” (Repeatedly
pressing the CH ▼ or
CH ▼▼button will alternate
between on and off.)
6
When finished, press the
VOL + button.
If no function buttons
(including remote control buttons or
front panel buttons) are operated for
three hours after the TV is turned on
with the “On time” feature, the TV
will be automatically turned off.
7
To set the Off time, press
the CH ▼▼button to select
“Off time.”
Press the VOL + button
and set the hours and
minutes. (Follow the same
procedure as in steps 1~6
above.)
8
When finished setting the timer, press the MENU button
three times to exit.
Setting the Sleep Tim er
The sleep timer automatically shuts off the TV after a preset time
(from 10 to 180 minutes).
After about 5 seconds, the sleep
display will disappear from the
screen, and the time interval will be
set.
1
Press the SLEEP button on the remote control.
2
Press the SLEEP button repeatedly until the appropriate time
interval appears (any of the preset values from “Off” to “180”).
4.10
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Sound Features
Choosing a Multi-Channel Sound (MTS) Soundtrack
Depending on the particular program being broadcast, you can listen to Stereo, Mono,
or a Separate Audio Program. (SAP audio is usually a foreign-language translation.
Sometimes SAP has unrelated information like news or weather.)
1
Press the MENU button to
display the menu.
Press the CH▼ button
once to select the
“Sound” menu.
2
Press the VOL + button to
select the Sound menu.
Press the CH▼▼button five
times to select “MTS”.
The text at the bottom of the
menu tells you if the incoming
audio is Stereo, SAP, or Mono.
3
Press the VOL + button
repeatedly to select
“Mono,” “SAP,” or
“Stereo.”
Press the MENU button
twice to exit
•
•
Choose Stereo for channels that are broadcasting in stereo.
Choose Mono for channels that are broadcasting in mono, or if you are
having difficulty receiving a stereo signal.
•
Choose SAP to listen to the Separate Audio Program, which is usually a
foreign-language translation.
You can also change the MTS setting by pressing the “MTS” button on the remote
control. (When you change channels, MTS is set to “Stereo” automatically.
To listen in ‘SAP’ or ‘Mono,’ change the MTS setting.)
CHAPTER FOUR: SPECIAL FEATURES
4.11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Extra sound settings (Turbo Sound, Surround, or Auto Volum e)
• Turbo Sound
Turbo sound emphasizes the bass and treble frequencies to add fullness to the sound.
• Surround
Your Samsung TV can create a "surround" effect such that the sound seems to come
from all directions. Once the “Surround” is set to “On”, the setting applies to sound
effects such as Standard, Music, Movie and Speech.
• Auto Volume
Each broadcasting station has its own signal conditions, which can make it necessary
to adjust the volume every time the channel is changed. “Auto volume” lets you
automat-ically adjust the volume of the desired channel by lowering the sound output
when the modulation signal is high or by raising the sound output when the modula-
tion sig-nal is low.
1
Press the MENU button to
display the menu.
Press the CH▼ button
once to select the
“Sound” menu.
2
Press the VOL + button to
select the Sound menu.
Press the CH▼ button
twice to select “Turbo
sound”.
3
Press the VOL + button to
select “On”.
Press the MENU button
twice to exit
You can set Surround and Auto volume in the same way as setting Turbo
sound.
4.12
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
View ing Closed Captions
Your TV decodes and displays the closed captions that are broadcast with certain TV shows.
These captions are usually subtitles for the hearing impaired or foreign-language trans-
lations. All VCRs record the closed caption signal from television programs, so home-record-
ed video tapes also provide closed captions. Most pre-recorded commercial video tapes pro-
vide closed captions as well. Check for the closed caption symbol in your television schedule
and on the tape’s packaging:
.
1
Press the MENU button to
display the menu.
Press the CH ▼▼button
three times to select the
“Function” menu.
Press the VOL+ button.
2
Press the CH ▼ button
twice times to select the
“Caption” menu.
Press the VOL+ button to
open the Caption menu.
Misspellings and unusual
characters sometimes occur during
closed caption transmissions, especial-
ly those of live events. There may be a
small delay before captions appear
when you change channels. These are
not malfunctions of the TV.
3
Press the VOL+ or VOL –
button to turn closed cap-
tioning on/off.
In caption mode, captions
appear at the bottom of the screen,
and they usually cover only a small
portion of the picture.
4
Press the CH ▼ button to
highlight “Mode.”
In text mode, information unrelated
to the program, such as news or
weather, is displayed. Text often
covers a large portion of the screen.
Press the VOL – or VOL +
button to select “Caption”
or “Text.”
Different channels and fields
display different information: Field 2
carries additional information that
supplements the information in
Field 1. (For example, Channel 1
may have subtitles in English, while
Channel 2 has subtitles in Spanish.)
5
Depending on the particular broadcast, it might be necessary to
make changes to “Channels” and “Field”:
Use the CH ▼, CH ▼, VOL + and VOL - buttons to make the
changes. (Follow the same procedure as in steps 3~4 above.)
Press the MENU button three times to exit.
CHAPTER FOUR: SPECIAL FEATURES
4.13
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
Using the V-Chip (Only USA)
The V-Chip feature automatically locks out programming that is deemed inappropriate for
children. The user must first enter a PIN (personal ID number) before any of the V-Chip
restrictions can be set up or changed.
Note : When the V-chip feature is active, channel-auto program features do not function.
Setting Up Your Personal ID Num ber (PIN)
1
Press the MENU button to
display the menu.
Press the CH ▼▼three
times to select the
“Function” menu.
Press the VOL + button.
2
Press the CH ▼▼button
five times to select the
“V-chip” menu.
Press the VOL+ button.
The “Enter pin” screen will appear. Enter your 4-digit PIN
number. Note: The default PIN number for a new TV set is
“0-0-0-0.”
3
After entering a valid PIN
number, the “V-chip”
screen will appear.
Press the CH ▼ button
three times and highlight
“Change pin.”
Note: If you forget the PIN,
press the remote-control keys in the
following sequence, which resets the
pin to 0-0-0-0:
4
While the “Change pin”
field is selected, press the
VOL+ button. The Change
pin screen will appear.
Choose any 4-digits for
your PIN and enter them.
POWER OFF ▼▼MUTE ▼▼8 ▼▼2 ▼
4 ▼▼POWER ON.
As soon as the 4 digits are entered, the “Confirm new pin”
screen appears. Re-enter the same 4 digits. When the
Confirm screen disappears, your PIN has been memorized.
Press the MENU button three times to exit.
4.14
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
How to Enable/ Disable the V-Chip
1
Press the MENU button to
display the menu.
Press the CH ▼▼button
three times to select the
“Function” menu.
Press the VOL + button.
2
Press the CH ▼▼button
five times to highlight the
“V-chip” menu.
Press the VOL+ button.
The “Enter pin” screen
will appear. Enter your 4-
digit PIN number.
3
The “V-Chip” screen will
appear, and “V-Chip lock”
will be selected (turns
blue color).
To enable the V-Chip fea-
ture, press the VOL+ but-
ton so that the “V-Chip
lock” field is Yes.
(Pressing the VOL+ button
will alternate between Yes
and No.)
How to Set up Restrictions Using the “TV guidelines”
First, set up a personal identification number (PIN), and enable the V-Chip. (See previous
section.) Parental restrictions can be set up using either of two methods: The TV guide-
lines or the MPAA rating.
1
Press the MENU button to
display the menu.
Press the CH ▼▼button
three times to select the
“Function” menu.
Press the VOL + button.
CHAPTER FOUR: SPECIAL FEATURES
4.15
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
2
Press the CH ▼▼button
five times to select the “V-
chip” menu.
Press the VOL+ button.
The “Enter pin” screen
will appear. Enter your 4-
digit PIN number.
3
The “V-chip” screen will
appear. Press the CH ▼
button, and highlight the
field for “TV guidelines.”
Note: These categories consist of
two separate groups: TV-Y and TV-Y7
(young children through age 7), and
TV-G through TV-MA (everybody
else).
4
Press VOL+. The “TV
guidelines” screen will
appear. Press the CH ▼,
CH ▼▼buttons to highlight
one of the six age-based
categories:
The restrictions for these two groups
work independently: If a household
includes very young children as well
as young adults, the TV guidelines
must be set up separately for each age
group. (See next step.)
TV-Y
TV-Y7
Young children
Children 7 and over
--------------------------------------
TV-G General audience
TV-PG Parent guidance
TV-14 Viewers 14 and over
TV-MA Mature audience
5
At this point, one of the TV-Ratings is highlighted (blue color).
Press the VOL+ button: Depending on your existing setup, a letter “U” or “B” will start blinking.
(U= Unblocked, B= Blocked)
While the “U” or ”B” is red, press the CH ▼ or CH ▼ button to block or unblock the category.
Press MENU once to save the TV guidelines. A TV-Rating will be highlighted (BLUE), and no letters will blink.
To exit this screen, press the MENU button again. To select a different TV-Rating, press the CH ▼ or CH ▼ button
and then repeat the process.
Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to change
any of the following sub-ratings:
FV: Fantasy violence
D: Dialog
L: L
S: Sexual situation
V: Violence
Note 2: The V-Chip will automatically block certain categories that are “more restrictive.” For example, if you block
“TV-Y” category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the
categories in the “young adult” group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V)
work together similarly. (See next section.)
4.16
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
6
How to set the FV, D, L, S and V sub-ratings:
First, highlight one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous page).
Next, while the TV-Rating is highlighted (BLUE), repeatedly press the VOL+ button. This will cycle through
the available sub-ratings (FV,L, S, D or V).
A blinking letter (“U” or “B”) will be displayed for each sub-rating. While the “U” or “B” is blinking, press
CH ▼ or CH ▼ to change the sub-rating.
Press MENU once to save the TV guidelines. A TV-Rating will be highlighted (BLUE), and no letters will blink.
To exit this screen, press MENU again. To select a different TV-Rating, press CH ▼ or CH ▼ and then repeat
the process.
Note: The V-chip will automatically block certain categories that are “More restrictive”. For example, if you
block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TV-MA will automatically be blocked.
7
Press the MENU button three times to clear all the screens. (Or proceed to the next section, and set up
additional restrictions based on the MPAA codes).
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-
13, R, NC-17, X
The MPAA rating system uses the Motion Picture Association of America (MPAA) system,
and its main application is for movies. (Eventually, movie videocassettes will be encoded
with MPAA ratings.) When the V-Chip lock is on, the TV will automatically block any
programs that are coded with objectionable ratings (either MPAA or TV-Ratings).
1
Press the MENU button to
display the menu.
Press the CH ▼▼button
three times to select the
“Function” menu.
Press the VOL + button.
2
Press the CH ▼▼button
five times to select the “V-
chip” menu.
Press the VOL+ button.
The “Enter pin” screen
will appear. Enter your 4-
digit PIN number.
CHAPTER FOUR: SPECIAL FEATURES
4.17
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL FEATURES
3
The “V-chip” screen will
appear. Press the CH ▼
button twice, and select
“MPAA rating.”
4
While “MPAA rating” is
selected, press the VOL+
button. The “MPAA rat-
ing” screen will appear.
G
General audience (no restrictions).
Parental guidance suggested.
5
PG
Repeatedly press the CH
▼▼button to select a
particular MPAA catego-
ry. (When a category is
selected, its color
PG-13 PG-13 (Parents strongly cautioned).
R
R (Restricted. Children under 17 should
be accompanied by an adult).
NC-17 No children under age 17.
changes to blue.)
X
X (Adults only).
Not rated.
Pressing the CH ▼ button
will cycle through the
MPAA categories:
NR
While a particular category is selected, press the VOL+ button to activate it.
A letter (“U” or “B”) will be displayed. Press the CH ▼▼or CH ▼▼button to select “U” or”B”.
Press the MENU button four times to save the settings and to clear all screens.
Note: The V-Chip will automatically block any category that is “more restrictive.” For example, if you
block the “PG-13” category, then “R,” “NC-17,” and “X” will automatically be blocked also.
How to Reset the TV after the V-Chip Blocks a Channel
(“Em ergency Escape”)
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following mes-
sage will appear: “Excessive rating.”
To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions
(depending on the rating of the local TV programs) the V-Chip might lock out all the channels. In this case, use
the V-Chip function for an “emergency escape”:
Press the MENU button to display the menu. Press CH ▼▼three times to select the “Function” menu and press
the VOL + button.
Press the CH ▼button five times to highlight the “V-chip” menu and press the VOL + button. Enter your PIN num-
ber, and press the VOL+ button to temporarily disable the V-Chip Lock.
4.18
CHAPTER FOUR: SPECIAL FEATURES
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch a p t e r Fiv e
TRO UBLESHO O TING
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, then call your nearest service center.
Identifying Problem s
Problem
Possible Solution
Poor picture
Try another channel.
Adjust the antenna.
Check all wire connections.
Poor sound quality.
No picture or sound.
Try another channel.
Adjust the antenna.
Try another channel.
Press the TV/VIDEO button.
Make sure the TV is plugged in.
Check the antenna connections.
No color, wrong colors or tints.
Make sure the program is broadcast in color.
Adjust the picture settings.
If the set is moved or turned in a different
direction, the power should be OFF for at least
30 minutes.
Picture rolls vertically.
The TV operates erratically
The TV won’t turn on.
Adjust the antenna.
Check all wire connections.
Unplug the TV for 30 seconds, then try
operating it again.
Make sure the wall outlet is working.
CHAPTER FIVE: TROUBLESHOOTING
5.1
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Cleaning and Maintaining Your TV
With proper care, your TV unit will give you many years of service. Please follow these
guidelines to get the maximum performance from your TV.
Placem ent
•
•
Do not place the TV near extremely hot, cold, humid or dusty places.
Do not place the TV near appliances with electric motors that create magnetic fields,
such as vacuum cleaners.
•
Keep the ventilation openings clear; do not place the TV on a soft surface, such as
cloth or paper.
•
Place the TV in a vertical position only.
Liquids
•
Do not handle liquids near or on the TV. Liquids that spill into it can cause serious
damage.
Cabinet
•
•
Never open the cabinet or touch the parts inside.
Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or
chemicals.
•
Do not put heavy objects on top of the cabinet.
Tem perature
•
If your TV is suddenly moved from a cold to a warm place, unplug the power cord,
and allow at least two hours for moisture that may have formed inside the unit to dry
completely.
Using Your TV in Another Country
If you plan to take your TV with you to a foreign country, please be aware of the different
television systems that are in use around the world. A TV designed for one system may
not work properly with another system due to differences in the TV channel frequencies
Specifications
TXL2791F / TXM2790F / TXM3292F
Model
AC 120V
60Hz
Voltage
Frequency of Operation
Power Consumption
140 Watts / 140 Watts / 156 Watts
A.1
APPENDIX
Download from Www.Somanuals.com. All Manuals Search And Download.
|