Raymarine Two Way Radio Ray215 User Guide

Ray215

VHF Radio

Ow ner ' s Handbook

Download from Www.Somanuals.com. All Manuals Search And Download.

RAY215

Modular

VHF Radio

Owner’s

Handbook

Document number: R49013_2

Date: March 2002

Download from Www.Somanuals.com. All Manuals Search And Download.

Purpose

This handbook contains very important information on the installation,

operation, and maintenance of your new equipment. To get the best results

in operation and performance, please take the time to read this handbook

thoroughly.

RAY215

Raymarine radios comply with the Federal Communications Commission

(FCC) and Industry Canada requirements that regulate marine VHF radio

usage for the US and Canada, respectively.

Marine VHF radio users in the US must comply with all applicable FCC

rules and regulations, which are described in Section 6. This information

was current at the time this handbook was printed. Up-to-date information,

including licensing requirements, can be obtained on the FCC website at:

www.fcc.gov/wtb/marine

Official FCC forms can be obtained on the FCC website at:

www.fcc.gov/formpage.html

FCC NOTICE

This device complies with Parts 15 and 80 of the FCC Rules. Operation is

subject to the conditions that this device does not cause harmful

interference. Changes or modifications to this equipment not expressly

approved in writing by Raymarine, Incorporated could violate compliance

with FCC rules and void the operator’s authority to operate the equipment.

FCC Licensing

An FCC Ship Radio Station License, Call Sign, and Operator License are

not required for most recreational vessels travelling in US waters. For

specifics on FCC licensing requirements, see Section 6 of this handbook.

Maritime Mobile Service Identity (MMSI)

The RAY215 includes equipment for Digital Selective Calling (DSC). A

nine-digit Maritime Mobile Service Identity (MMSI) number is required to

operate the DSC equipment. You can request an MMSI number from the

FCC when you apply for a Station License. If your vessel does not require

a license, you may obtain an MMSI by contacting either BoatUS

(www.boatus.com) or MariTEL(www.maritelusa.com). Once obtained, you

can program the MMSI number into your RAY215 as described in this

handbook.

Download from Www.Somanuals.com. All Manuals Search And Download.

INDUSTRY CANADA

You do not need a license to operate this radio within sovereign waters of

Canada or the US. You will need a license to operate this radio outside of

Canada or the US. To obtain Industry Canada licensing information, contact

the nearest field or regional office, or write:

Industry Canada

Radio Regulatory Branch

Attention: DOSP

300 Slater Street

Ottawa, Ontario

Canada, KIA OC8

The following information about the radio is required to complete the

license application:

Industry Canada Certification Number

FCC Type Number

FCC Type Accepted

Output Power

4069823229AV

PJ5RAY215

Parts 15 and 80

1 watt (low) & 25 watts (high)

16FE (FM)

Modulation

Frequency Range

156.025-157.425

SAFETY NOTICE

This device is only an aid to navigation. Its performance can be affected

by many factors including equipment failure or defects, environmental

conditions, and improper handling or use. It is the user's responsibility to

exercise common prudence and navigational judgement, and this device

should not be relied upon as a substitute for such prudence and judgement.

Your Raymarine VHF radio generates and radiates radio frequency (RF)

electromagnetic energy (EME). This equipment must be installed and

operated in accordance with the instructions contained in this handbook.

Failure to do so can result in personal injury and/or product malfunction.

Antenna Mounting and EME Exposure

For optimal radio performance and minimal human exposure to radio

frequency electromagnetic energy, make sure the antenna is:

• connected to the radio before transmitting

• properly mounted

• located where it will be away from people

• located at least three feet (91cm) from the RAY215 and the microphone/

handset

Download from Www.Somanuals.com. All Manuals Search And Download.

iii

Safe Compass Difference

Safe Compass Distance is 1 meter for a common mechanical compass;

other compass types may require greater distances. To be sure, you should

locate the radio as far as possible from the compass. Test your compass to

verify proper operation while the radio is also operating.

Adjustments or Repair

Adjustments require specialized service procedures and tools only available

to qualified service technicians – there are no user serviceable parts or

adjustments. The operator should never remove the cover or attempt to

service the equipment.

Raymarine products are supported by a network of Authorized Service

Representatives. For product information you may contact the following

regional centers:

United States

Raymarine, Inc.

22 Cotton Road, Unit D

Nashua, NH 03063-4219

USA

Telephone:

603-881-5200

800-539-5539

603-864-4756

Fax:

Europe

Raymarine Ltd

Anchorage Park

Portsmouth, Hampshire

England PO3 5TD

Telephone:

Fax:

+44 (0) 23 9269 3611

+44 (0) 23 9269 4642

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Section 1 General Description

1.1 Introduction .......................................................................... 1-1

1.2 Equipment Features............................................................... 1-1

1.3 Microphone / Handset Options ............................................ 1-2

Section 2 Installation

2.1 Unpacking and Inspection .................................................... 2-1

2.2 Equipment Supplied .............................................................. 2-1

2.2.1

Optional Accessories............................................... 2-1

2.3 Planning the Installation ....................................................... 2-2

2.3.1

2.3.2

Typical Mounting Methods .................................... 2-2

Flush Mounting....................................................... 2-3

2.4 Electrical Connections........................................................... 2-6

2.4.1

2.4.2

2.4.3

2.4.4

2.4.5

2.4.6

DC Power and External Speaker Connections.......... 2-6

External Speaker Connections ................................. 2-7

NMEA Data ............................................................. 2-8

Antenna Connections ............................................. 2-8

Antenna Mounting Suggestions............................. 2-9

Grounding................................................................ 2-9

Section 3 Operation with Standard Fist Microphone

3.1 Introduction .......................................................................... 3-1

3.1.1

3.1.2

Microphone/Full Function Handset Priority ........... 3-1

Microphone/Handset Connections ......................... 3-2

3.2 Control and LCD Display ...................................................... 3-3

3.2.1

3.2.2

Controls ................................................................... 3-3

LCD Display ............................................................ 3-6

3.3 Operating Procedures............................................................ 3-8

3.3.1

3.3.2

3.3.3

3.3.4

3.3.5

3.3.6

3.3.7

3.3.8

3.3.9

Turning the Power On ............................................. 3-8

Setting the Squelch.................................................. 3-8

Setting the Volume ................................................... 3-8

Setting the Power Output ........................................ 3-8

Setting the Channel ................................................. 3-8

Setting the Frequency Mode ................................... 3-9

Transmitting ............................................................ 3-9

Selecting a Weather Channel ................................... 3-9

Priority Channel ..................................................... 3-10

3.3.10 Desensitized Reception ......................................... 3-10

3.3.11 Channel Memory ................................................... 3-10

Download from Www.Somanuals.com. All Manuals Search And Download.

3.3.12 Resetting Factory Defaults .................................... 3-10

3.3.13 Scan Modes........................................................... 3-11

3.3.14 Monitor Mode ....................................................... 3-12

3.3.15 LCD Backlight Function ........................................ 3-12

3.3.16 NMEA Operation ................................................... 3-13

3.3.17 Digital Selective Calling (DSC).............................. 3-14

3.3.17.1 MMSI Number Setup ...................................... 3-15

3.3.17.2 Individual Ship's Call ...................................... 3-16

3.3.17.3 All Ships Call .................................................. 3-24

3.3.17.4 Group Call ....................................................... 3-25

3.3.17.5 Distress Call .................................................... 3-26

3.3.17.6 Distress Relay Call .......................................... 3-28

Section 4 Operation with Optional Full Function Handset

4.1 Introduction .......................................................................... 4-1

4.1.1

4.1.2

Microphone/Full Function Handset Priority ........... 4-1

Microphone/Handset Connections ......................... 4-2

4.2 Control and LCD Display ...................................................... 4-3

4.2.1

4.2.2

Controls ................................................................... 4-3

LCD Display ............................................................ 4-7

4.3 Radio Functions .................................................................... 4-9

4.4 Operating Procedures.......................................................... 4-10

4.4.1

4.4.2

4.4.3

4.4.4

4.4.5

4.4.6

4.4.7

4.4.8

4.4.9

Setting the Volume ................................................. 4-10

Setting the Squelch................................................ 4-10

Using the Function Key ........................................ 4-11

Setting the Frequency Mode ................................. 4-11

Receiving on the Weather Channels ..................... 4-12

Selecting the Channel ............................................ 4-12

Priority Channel ..................................................... 4-13

Channel Memory ................................................... 4-13

Setting the Transmission Power Output ................ 4-14

4.4.10 Desensitized Reception (Local Mode) ................... 4-14

4.4.11 LCD Backlight Function ........................................ 4-14

4.4.12 Intercom Mode ...................................................... 4-14

4.4.13 Scan Mode ............................................................ 4-16

4.4.14 Monitor Mode ....................................................... 4-17

4.4.15 NMEA Operation ................................................... 4-18

4.4.16 Digital Selective Calling (DSC) .............................. 4-19

4.4.16.1 Individual Ship Call (Ship-to-Ship) ................. 4-20

4.4.16.2 Individual Shore Call (Ship-to-Shore) ............. 4-23

4.4.16.3 Receiving Individual Ship’s Call ..................... 4-25

4.4.16.4 Transmitting a Group Call ............................... 4-26

Download from Www.Somanuals.com. All Manuals Search And Download.

4.4.16.5 Receiving Group Call ...................................... 4-28

4.4.16.6 TransmittingAll Ships Call ............................. 4-29

4.4.16.7 ReceivingAll Ships Call .................................. 4-30

4.4.16.8 Transmitting a Distress Call ............................ 4-30

4.4.16.9 Receiving a Distress Call ................................ 4-34

4.4.16.10 Receiving Distress Relay Call ......................... 4-35

4.4.16.11 Using the DSC Log ......................................... 4-36

4.5 Menu Operation .................................................................. 4-37

4.5.1

4.5.2

4.5.3

Selecting the Menu Operation ............................... 4-37

NAVSTAT Operation ............................................. 4-38

DSC Operation ....................................................... 4-39

4.5.3.1 Selecting Distress Call Type (NATURE) ......... 4-10

4.5.3.2 Manual Entry of Latitude/Longitude

(L/LENT) ........................................................ 4-41

4.5.3.3 Modifying the MMSI Number List

(PHNBOOK) .................................................... 4-43

4.5.3.4 Modifying the MMSI Group Number

(GROUP) ......................................................... 4-48

4.5.4

Setting the MMSI Number .................................... 4-50

Section 5 Maintenance

5.1 How to Contact Raymarine ................................................... 5-1

5.2 Preventive Maintenance ....................................................... 5-3

5.3 Specifications ........................................................................ 5-3

5.4 Drawings ............................................................................... 5-7

Section 6 Appendix

6.1 FCC Licensing Requirements ................................................ 6-1

6.2 Marine VHF Channel Usage Guide ....................................... 6-3

6.3 Marine VHF Channel Frequency Tables ............................. 6-12

Download from Www.Somanuals.com. All Manuals Search And Download.

vii

GLOSSARY OF TERMS

All Scan........................... Scans all channels

Canadian Channels ......... Channel designator as defined by Industry

Canada

Carrier Wave ................... A Radio Frequency on which intelligence is

superimposed.

DSC ................................. Digital Selective Calling

Dual Watch ..................... Monitor the Priority Channel (9 or 16) while

working on another channel

Duplex ............................. Transmit and receive on different frequencies

FCC ................................. Federal Communications Commission

FM .................................. Frequency Modulation

International Channels .... Channel designator as defined by the ITU

ITU .................................. International Telecommunications Union

LCD ................................. Liquid Crystal Display

Memory Scan .................. Scans only user selected memory channels

MMSI.............................. Maritime Mobile Service Identity; a number

issued by each country to identify maritime

stations.

NOAA ............................. National Oceanographic and Atmospheric

Administration

PLL .................................. Phase Locked Loop (a type of frequency

synthesizer)

PTT switch ...................... Microphone push-to-talk switch

RF.................................... Radio Frequency

RTCM.............................. Radio Technical Commission for Maritime

Services

RX ................................... Receiver

Simplex ............................ Transmit and receive on the same frequency

Squelch ........................... A circuit that sets the threshold for cutting off

the receiver when the signal is too weak for

reception of anything but noise

TX ................................... Transmit

Tri-Watch ........................ Monitor the Priority Channel and Weather

Channels while working on another channel

US Channels ................... Channel designations as defined by the FCC

VCO................................. Voltage Controlled Oscillator

VHF ................................. Very High Frequency 30MHz to 300MHz

Weather Channels........... Channels for routine and emergency weather

information broadcast by NOAA

Download from Www.Somanuals.com. All Manuals Search And Download.

viii

Download from Www.Somanuals.com. All Manuals Search And Download.

1-1

General Description

Section 1

General Description

1.1 Introduction

Congratulations on your purchase of Raymarine's RAY215 marine

radiotelephone. This handbook describes the physical and functional

characteristics of the radiotelephone.

The RAY215 is a microprocessor-controlled, digitally synthesized,

compact transceiver that provides reliable simplex and semi-duplex (two-

frequency) communications. The RAY215 provides two-way

communications on Marine channels and reception on 10 separate weather

channels. More importantly, the RAY215 has built-in Digital Selective

Calling (DSC) in accordance with RTCM standard SC-101 for sending

and receiving DSC Distress, All Ships, Individual Ship, and Group calls.

The RAY215 can transmit and receive on all available US, Canadian, and

International Marine VHF radiotelephone channels. There are channels

that are FCC approved but may only be used by authorized stations for

specific purposes, depending on the type of vessel (commercial or non-

commercial). Refer to the of Frequency Tables in Section 6, which list all

marine VHF channels available in your RAY215. You should familiarize

yourself with these tables to ensure proper channel usage.

1.2 Equipment Features

The RAY215 is designed and manufactured to provide ease of operation

with excellent reliability. The important built-in features of the equipment

are listed below.

• Built-in DSC in accordance with RTCM standard SC-101

• Exclusive circuit that automatically selects 16 or 9 as the Priority Channel

when the radio is turned on

• Dedicated key for changing the Priority Channel (16/9)

• Exclusive weather alert feature (when in monitor mode)

• Waterproof to CFR-46 standard for Fist Microphone and Base Station

• Waterproof to JIS-7 standard for Optional Full Function Handset

• Dedicated DISTRESS key on back of handset, with spring loaded

protective cover

• All Scan and Memory Scan features

• Dual/Tri-Watch Monitor modes

• Intercom operation between Fist Microphone and Optional Full Function

Handset (second station)

Download from Www.Somanuals.com. All Manuals Search And Download.

1-2

General Description

• Distant/local mode

• Oversized LCD

• All solid-state circuitry for low current drain and maximum reliability

• Series relay protection on input power circuits to prevent reverse polarity

damage

• High-performance receiver section with optimum selectivity

1.3 Microphone / Handset Options

The RAY215 can be operated with the standard Fist Microphone, an

optional Full Function Handset with additional features, or both. Operation

with both units installed enables intercom capabilities between the two

stations.

The Fist Microphone features up/down channel select keys, Priority

Channel (16 or 9) selection button, plus a quick access DSC Distress key.

The optional Full Function Handset provides you with all the features of

the fist microphone plus a full alphanumeric keypad, expanded LCD

display, volume and squelch level controls, DSC distress calls that describe

the type of distress, dedicated keys for Individual and All Ships DSC

calls, and expanded ship and shore phonebooks for making DSC Individual

calls.

Either unit can be located in a remote location using the optional Handset/

Microphone Relocation Kit.

The Single Station Full Function Handset with cradle (Raymarine part

number E46019) is used in lieu of the Fist Microphone. The Dual Station

Full Function Handset (Raymarine part number E46021), which includes

a cradle and external speaker, is used in conjunction with the Fist

Microphone to enable intercom communications between the two stations.

Note: The RAY215 is designed to have the base station as the priority

unit. Therefore, Raymarine recommends installing the base station in the

radio operating room or the location from which the ship is normally

navigated. If an optional second station Full Function Handset is also

installed, that handset should be installed in the remote location.

See Section 3 for a complete discussion of operation using the Fist

Microphone. Section 4 describes using the RAY215 with the optional

Full Function Handset.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-1

Installation

Section 2

Installation

2.1 Unpacking and Inspection

Use care when unpacking the unit from the shipping carton to prevent

damage to the contents. It is also good practice to save the carton and the

interior packing material in the event you must return the unit to the factory.

2.2 Equipment Supplied

The following is a list of materials supplied with the RAY215:

Description

Part No.

E43003

RAY215 Radiotelephone

Fist Microphone with Cradle & Hardware R49015

Power/Optional Speaker/NMEA Cable

Mounting Yoke

R49017

R49011

R49012

R49013

R49014

Yoke Knob

Handbook, RAY215

Sun Cover

2.2.1 Optional Accessories

The following is a list of options available for the RAY215:

Description

Part No.

E46019

Single Station:

Full Function Handset with Cradle

Second Station:

Full Function Handset with Cradle

E46021

7 meter Handset Extension Cable

External Powered Handset Speaker

Handset/Microphone Relocation Kit

E46026

5m Extension Cable, Full Function Handset E46018

10m Extension Cable, Full Function Handset E46017

3m Extension Cable, External Speaker

External 10W Speaker

E46015

E46006

E46023

M51118E

Flush Mounting Kit

8' Fiberglass VHF Antenna

Download from Www.Somanuals.com. All Manuals Search And Download.

2-2

Installation

2.3 Planning the Installation

When planning the installation of your RAY215, the following conditions

should be considered to ensure dependable and trouble-free operation.

Mount the Base Station Transceiver using the Mounting Template

provided.

The Base Station Transceiver is designed to be mounted horizontally or

vertically on a flat bulkhead. Select a location that is non-metallic, dry,

protected, well-ventilated, and free from high operating temperatures and

excessive vibration. Provide sufficient space behind the transceiver to

allow for proper cable connections to the rear panel connectors. Locate

the transceiver as near as possible to the power source yet as far apart as

possible from any devices that may cause interference such as motors,

generators, and other on board electronics. The transceiver should be

protected from prolonged direct exposure to rain and salt spray.

The transceiver is NOT designed to be mounted in engine compartments.

Do NOT install the transceiver in a location where there may be flammable

vapors (such as in an engine room or compartment, or in a fuel tank bay),

water splash or spray from bilges or hatches, where it is at risk from physical

damage from heavy items (such as hatch covers, tool boxes, etc.), or where

it might be covered by other equipment. Locate the Base Station

Transceiver and Handset at least 3 feet from the antenna.

Safe Compass Distance is 1 meter for a common mechanical compass;

other compass types may require greater distances. To be sure, you should

locate the radio as far as possible from the compass. Test your compass to

verify proper operation while the radio is also operating.

Mount the base station transceiver to allow easy access from the location

where the ship is normally navigated.

2.3.1 Typical Mounting Methods

The RAY215 can be conveniently mounted on a chart table, bulkhead,

overhead, or any other desired location. Refer to Figure 2-1 for typical

mounting methods.

CAUTION

Make sure there are no hidden electrical wires or other items behind

the desired location before proceeding. Check that free access for

mounting and cabling is available.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-3

Installation

Figure 2-1 Typical Mounting Methods

2.3.2 Flush Mounting

In addition to the typical Mounting Methods, the RAY215 may also be

flush mounted using the optional Flush Mount Kit. These kits are available

from your Raymarine dealer or our Customer Service Department.

There are two methods of mounting the radio using the flush mount kit:

from the front or rear of the console. Choose the method that best suits

your console.

1. Select the location for the radio transceiver. A clear, flat area, of

sufficient height having at least 9" of clear depth behind the panel is

required.

CAUTION

Make sure there are no hidden electrical wires or other items behind

the desired location before proceeding. Check that free access for

mounting and cabling is available.

2. Unpack the Flush Mount kit and confirm that all hardware is present.

3. Mark the cutout area using the cutout guide.

4. Drill a pilot hole inside of the cutout guide area.

5. Using an appropriate saw, carefully cut along the cutout line.

6. Remove the yoke knobs and the mounting yoke from the transceiver.

Check that the radio will fit into the cutout area.

Front Mounting

7. Insert the rear of the transceiver through the flush mount bracket such

that the tabs on the bracket point away from the radio’s front bezel.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-4

Installation

8. Continue to push the bracket onto the transceiver until it is flush with

the front bezel.

9. On each side of the transceiver, insert a screw through the bracket tab

and into the threaded holes from which you removed the yoke knobs.

10. Tighten the screws.

11. It is recommended to run a bead of RTV or similar sealant around the

inside edge of the bracket to avoid water entry behind the console.

12. Insert the radio and attached bracket into the cutout.

13. Install four flat head screws through the four countersunk holes in the

front of the bracket and secure into the console.

14. From behind the console, connect the power/optional speaker and

antenna cables.

Rear Mounting

7. It is recommended to run a bead of RTV or similar sealant around the

inside edge of the bezel to avoid water entry behind the console.

8. Insert the radio into the cutout until the front bezel is flush with the

console.

9. From behind the console, push the flush mount bracket over the rear

of the transceiver such that the tabs on the bracket point away from

the radio’s front bezel.

10. Continue to push the bracket onto the transceiver until it is flush with

the console.

11. On each side of the transceiver, insert a screw through the bracket tab

and into the threaded holes from which you removed the yoke knobs

but do not fully tighten at this time.

12. Install four pan head screws through the four holes in the bracket and

secure the bracket into the console.

13. From the front, make sure the transceiver is still flush with the console.

14. From behind the console, fully tighten the screws that secure the bracket

to the radio’s threaded yoke knob holes.

15. Connect the power/optional speaker and antenna cables.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-5

Installation

1 (25)

0.35 (9)

5.47 (139)

6.69 (170)

Figure 2-2 Outline and Mounting Dimensions

All dimensions are shown in inches and (millimeters)

Download from Www.Somanuals.com. All Manuals Search And Download.

2-6

Installation

2.4 Electrical Connections

2.4.1 DC Power and External Speaker Connections

The 6-foot long power cable is a multi-purpose assembly containing three

wire-pairs for connections to DC power, NMEA input, and an optional

speaker. Connections to the 6-pin connector are as follows:

Wire Color Function

Connects to

RED

BLACK

Power +

Power −

Ship's 13.6 VDC power

YELLOW

GREEN

Speaker +

Speaker −

External speaker

BLUE

PURPLE

NMEA +

NMEA −

Input from position source (GPS, etc.)

The RED (+) power wire contains a 10 amp in-line fuse.

Figure 2-3 Power/External Speaker/NMEA Cable and 6 Pin Connector

In most cases the length of the power cable should be adequate enough to

reach the DC power source. If additional wire length is required, the cable

can be extended by adding more cable as necessary. However, for power

cable runs longer than 15 feet, larger wire diameter size should be used to

prevent voltage line loss.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-7

Installation

Figure 2-4 Power Cable Length

Your RAY215 should be connected to the nearest primary source of ship's

DC power. A typical source may be a circuit breaker on the power panel

or a fuse block near the unit. When connecting to either of these sources,

the circuit breaker or other in-line fuse should be rated at 10 amps.

It is recommended that lugs be used to connect the power cable to the DC

supply and the lug connections should be both crimped and soldered.

This is very important in order to ensure adequate current draw to the

equipment. Intermittent operation may result if an insufficient connection

is made to the power source. The connection terminal should be clean,

with no sign of corrosion.

The red (+) wire is connected to the positive terminal of the power source.

The black (-) wire is connected to the negative (ground) of the power

source. Should the power connections be inadvertently reversed, the unit

will not power up but no damage will occur. Check the polarity with a

VOM (Voltage/Ohm Meter) and reconnect observing correct polarity. If

the fuse ever needs replacement, be sure to use the same type and rating.

2.4.2 External Speaker Connections

The yellow (+) wire and green (-) wire are used for connecting the RAY215

to an external speaker (see Figure 2-3), such as Raymarine’s 10W External

Speaker (part number E46006).

Four watts of audio output power are provided for an external 4-ohm

speaker.Asuitable speaker can be purchased from your local marine dealer.

Connect the yellow (+) wire and green (-) wire to the speaker observing

polarity as it is marked on the speaker. When connected, the external

speaker will function simultaneously with the internal speaker.

CAUTION: DO NOT short the green (-) wire to the yellow (+) wire.

DO NOT short the green (-) wire to the black Power (-) wire.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-8

Installation

2.4.3 NMEA Data

The RAY215 accepts NMEA0183 data from a position determining device

(GPS, etc.) to provide the Latitude and Longitude position information

that is transmitted during a DSC Distress Call.

Connect the input(s) of the positioning device to the blue (NMEA+) and

purple (NMEA-) wires in the Power/Optional Speaker/NMEA cable.

An example of how to connect the NMEA cables and power supply using

a suitable connector block is shown in the diagram below. For specific

instructions how to connect your particular GPS, please refer to the

handbook that came with that device.

Note: For non-differential GPS, all return connections (-) must be tied to

a common ground reference.

Red

+12 V

Yellow

+ NMEA Data (blue)

Black

-- NMEA Data (purple)

Figure 2-5 GPS Connections

2.4.4 Antenna Connections

Your coaxial VHF antenna cable connects to the RAY215 antenna cable

on the rear panel using a PL259 VHF type connector. Your VHF antenna

cable length can be critical to performance. If you are uncertain, contact a

professional installer or call Raymarine Product Support department. If a

longer cable length is required, RG-58 (50 ohm) coaxial cable or equivalent

cable can be used for runs up to a maximum of 50 feet. If the distance

required is even greater, Raymarine recommends using low loss RG-213

or equivalent cable for the entire run to avoid excessive losses in power

output.

If the antenna RF connector is likely to be exposed to the marine

environment, a protective coating of grease (Dow Corning DC-4 or similar)

can be applied to the connector before connecting it to the radio. Any

other extensions or adapters in the cable run should also be protected by

silicon grease and then wrapped with a waterproofing tape.

Download from Www.Somanuals.com. All Manuals Search And Download.

2-9

Installation

2.4.5 Antenna Mounting Suggestions

The best radio in the world is useless without a quality antenna and good

location. Mounting the VHF antenna properly is very important because

it will directly affect the performance of your VHF radio. AVHF antenna

designed for marine vessels should be used.

• Since VHF transmission is essentially Line-of-Sight, mount the antenna

at the highest possible location on the vessel and free of obstruction to

obtain maximum range.

• If you must extend the length of the coaxial cable between the antenna

and the radio, use a coaxial cable designed for the least amount of power

loss over the entire cable length.

• Remember to maintain the recommended minimum 3 feet between the

radio and antenna.

2.4.6 Grounding

While special grounding is not generally required for VHF radiotelephone

installations, it is good marine practice to properly ground all electronic

equipment to the ship's earth ground system. The RAY215 can be

connected to ground by attaching a wire to one of the screws on the unit's

rear panel and then to the nearest ship's earth ground connection point.

The recommended wire to be used for such grounding is #10 AWG.

Figure 2-6 Typical Grounding Methods

Download from Www.Somanuals.com. All Manuals Search And Download.

2-10

Installation

Download from Www.Somanuals.com. All Manuals Search And Download.

3-1

Operation with a Fist Microphone

Section 3 Operation with Standard

Fist Microphone

3.1 Introduction

The RAY215 can be operated with the standard Fist Microphone, or an

optional Full Function Handset that enables additional features, or both

units to enable intercom capabilities. This section describes using the

RAY215 with the Fist Microphone. See Section 4 for a discussion of

operation using the Full Function Handset.

3.1.1 Microphone / Full Function Handset Priority

When both a Fist Microphone and Full Function Handset are in use, only

one can have priority to make a call. When the Full Function Handset is

out of its cradle, it has priority over the Fist Microphone and the REMOTE

indicator illuminates on the LCD of the base station. When the Full

Function Handset is in the cradle, the Fist Microphone has priority and

the REMOTE indicator extinguishes.

Overriding the Full Function Handset

In an emergency, the base station can override the Full Function Handset

to make a call even though the handset has priority (is off the cradle). To

override the handset, press and hold the DSC/PRI key on the base station.

The REMOTE indicator flashes and the base station regains priority

control. Make your call as usual using the Fist Microphone. On the Full

Function Handset, OVERRIDE appears on the dot matrix display. In this

mode, all keys are disabled on the handset except for DISTRESS. The

base station retains control until the DSC/PRI key is again pressed and

held.

Note: The RAY215 is designed to have the base station as the priority

unit. You should install the base station and Fist Microphone in the radio

operation room or the location from which the ship is normally navigated.

If an optional second station Full Function Handset is also installed, that

handset is the one that should be installed in the remote location.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-2

Operation with a Fist Microphone

3.1.2 Microphone/Handset Connections

The Fist Microphone can be connected to the port on the front of the base

station (Figure 3-2) or mounted near the base station using the optional

Handset Relocation Kit (part number E46026), which is available from

your authorized Raymarine dealer/distributor. The Relocation Kit must

be connected to the HANDSET/RELOCATION KIT port on the rear of

the base station (Figure 3-1).

If both a Fist Microphone and Second Station Full Function Handset are

to be used, the Fist Microphone must be connected to the front port with

the Full Function Handset connected to the HANDSET/RELOCATION

KIT port on the rear. In this case, the Handset Relocation Kit could not be

used with the Fist Microphone. Once installed, the two stations can

communicate with one another using the Intercom function described in

Section 4.4.12.

Figure 3-1 Rear Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

3-3

Operation with a Fist Microphone

Figure 3-2 Layout of Controls

3.2 Control and LCD Display

3.2.1 Controls

Several of the keys on the front panel of the base station serve multiple

purposes. For the most part, the function indicated on the first line of

the key is accessed by pressing and releasing that key. The function

indicated on the second line of the key is accessed by pressing and

holding the key for two seconds.

CH (Channel Selection) Knob

This knob selects the active channel. Turning the knob clockwise

increments the channel number. Turning the knob counterclockwise

decrements the channel.

The knob is also used to select values and functions in DSC mode.

VOLUME/PWR Knob

This knob switches power on and off and controls the audio volume.

From the OFF position, rotating the knob clockwise until it "clicks"

powers ON the radio. Continuing to turn the knob clockwise, the

volume increases. Rotating the knob counterclockwise, the volume

decreases. Continuing to turn the knob counterclockwise, the unit

"clicks" OFF.

The upper bar graph on the LCD displays the volume level.

SQUELCH Knob

This knob controls the squelch sensitivity level. Rotating the knob

clockwise increases the squelch level. Rotating the knob

counterclockwise decreases the squelch.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-4

Operation with a Fist Microphone

The lower bar graph on the LCD displays the squelch level.

SCAN/ MEM Key

This key starts or stops All Scan and Memory Scan Modes. The key

also places favorite channels into the radio's memory for quick

selection.

Pressing and holding SCAN/MEM for 3 seconds stores into memory

the currently displayed channel and illuminates the MEM indicator

on the LCD. If the current channel has already been stored, pressing

SCAN/MEM removes the channel from memory and extinguishes

the MEM indicator.

Pressing and releasing SCAN/MEM when no channels have been

entered into memory initiates a scan of all available channels. The

SCAN indicator illuminates on the LCD.

When at least one channel has been programmed into memory,

pressing and releasing SCAN/MEM causes the MEM and SCAN

indicators to flash for 3 seconds. If the key is pressed again while

these indicators are flashing, the radio enters All Scan mode.

However, if the 3 seconds expire before pressing the key a second

time, the radio initiates a scan of only those channels programmed

into memory.

Pressing the SCAN/MEM key during All Scan or Memory Scan

terminates the scan.

WX/INT Key

Pressing and releasing WX/INT switches between the Weather

channel and the last used marine channel. Pressing and releasing

WX/INT while in the Dual Watch mode places the unit in Tri-Watch

mode. While in either Weather or Tri-Watch modes, the WX indicator

illuminates on the LCD.

Pressing and holding WX/INT for 2 seconds switches between the

US, Canadian, and International frequency groups. While in the

International Frequency mode, the INT indicator illuminates on the

LCD. While in the Canadian mode, the CAN indicator illuminates.

There is no indicator for US mode.

MON/ 1/25 Key

Pressing and releasing MON/1/25 initiates the Dual-Watch Monitor

mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-5

Operation with a Fist Microphone

Pressing and holding MON/1/25 for 2 seconds toggles the output

power between 1 and 25 watts. While in the 1 Watt mode, the 1W

indicator illuminates on the LCD.

Pressing this key while holding PTT overrides the 1W output setting.

See the Frequency tables in Section 6 for the affected channels.

16/9 Key

Pressing and releasing 16/9 switches the radio between the current

channel and the Priority Channel (9 or 16).

Pressing and holding 16/9 for 2 seconds toggles the Priority Channel

between 16 and 9.

D/L / I.C. Key

Pressing and releasing D/L / I.C. switches receiver sensitivity between

Distant (full) and Local (desensitized) modes.

While in the Local mode, the DESENS indicator is illuminated.

Holding D/L / I.C. for 2 seconds toggles on and off the Intercom

function between the microphone on the base station and an optional

remote Full Function Handset. Press PTT to converse with the other

station.

DSC/ PRI Key

Pressing and releasing the DSC/PRI and D/L / I.C. keys

simultaneously places the radio in DSC mode, which is used to make

Individual Ships Calls, Group Calls, All Ships Calls, and Distress

Calls.

DSC mode may be exited at any time by pressing the 16/9 key.

Pressing and holding DSC/PRI for 2 consecutive seconds returns

Priority control from an optional Second Station Full Function

Handset to the base station. This feature is for immediately taking

radio operation control from the second station in case of an

emergency.

DIM Key

Pressing this key once starts Dimmer mode, which adjusts the

brightness of LCD's backlight.

Each successive press of the DIM key switches the brightness from

Off, to Low, to Medium, to High, then back to Off.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-6

Operation with a Fist Microphone

PTT Key (Fist Microphone)

Pressing the PTT (Push To Talk) key enables the radio's transmitter.

PTT key operation is disabled when the selected channel is either a

Weather channel or a disallowed channel.

The radio is equipped with a 5 minute timeout timer as a safety feature.

After the PTT has been held continuously for 5 minutes, transmission

is discontinued and an alarm sounded until PTT is released.

Trackpad UP Key (Fist Microphone)

This key increments the channel number by 1 each time it is pressed.

If pressed and held, the channel increments at a rate of 10 channels

per second.

Trackpad DOWN Key (Fist Microphone)

This key decrements the channel number by 1 each time it is pressed.

If pressed and held, the channel decrements at a rate of 10 channels

per second.

16/9 Key (Fist Microphone)

Has the same function as the 16/9 key on the front panel controls.

DISTRESS Key (under hinged door on rear of microphone)

The DISTRESS key sends a DSC Distress Call when pressed and

held for 5 seconds.

3.2.2 LCD Display

The following describes the functional characters on the RAY215's LCD.

10 11

Figure 3-2 LCD Display Layout

NMEA indicator

Appears in every operation mode when valid NMEA data is being

received.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-7

Operation with a Fist Microphone

DSC indicator

Appears when the radio is in the DSC mode.

ACK indicator

Appears when receiving an acknowledgement to a DSC Individual

or Distress Call.

INT indicator

Appears when the International frequency group is selected.

CAN indicator

Appears when the Canadian frequency group is selected.

TX indicator

Appears during transmission.

1W indicator

Appears when the current transmission output is set at 1W.

(The indicator is extinguished when the output is set at 25W.)

MEM indicator

Appears when a channel on the display is stored in memory and

during a Memory Scan operation.

SCAN indicator

Appears during a scan operation.

DESENS indicator

Appears when the radio is in the Desensitized (local) mode.

MON indicator

Appears when the radio is in the Dual Watch or Tri-Watch Monitor

mode.

WX indicator

Appears when the radio is in the Weather Channel or Tri-Watch

modes.

REMOTE indicator

Appears when the optional, remote Full Function Handset has the

priority operation.

Channel display (Large)

Displays the current channel number.

Channel display (Small)

Displays the Priority Channel number while the radio is in the Monitor

mode and function indicators during DSC mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-8

Operation with a Fist Microphone

VOL indicator (in bar graph)

Represents the current sound volume level. Alouder volume displays

a larger number of segments in the bar graph.

SQL indicator (in bar graph)

Represents the current squelch level. A deeper squelch displays a

larger number of segments in the bar graph.

3.3 Operating Procedures

3.3.1 Turning the Power On

Rotate the VOLUME/PWR knob clockwise to turn the radio on.

3.3.2 Setting the Squelch

Rotate the SQUELCH knob counterclockwise until audio is heard. Rotate

clockwise until the squelch "quiets".

3.3.3 Setting the Volume

With audio present, rotate the VOLUME knob clockwise for the desired

volume level.

3.3.4 Setting the Power Output

Press the MON/1/25 key for two seconds to toggle between 1 watt output

and 25 watts output. When the 1W indicator is displayed, the output power

is 1 watt. If 1W is extinguished, 25 watts is being output.

The choice of power output is dependent upon the distance of transmission

and transmitting conditions. In certain US harbors and on certain channels,

the FCC requires the power to be limited to 1 Watt. On these "required"

channels, the radio automatically selects 1 watt power output when the

channel is selected.

3.3.5 Setting the Channel

To select the appropriate channel, rotate the CH (Channel Select) Knob

clockwise/counterclockwise or use the Channel UP/DOWN keys on the

microphone.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-9

Operation with a Fist Microphone

3.3.6 Setting the Frequency Mode

The frequency modes available are US, International, and Canadian.

If the CAN and INT indicators are not illuminated, then US channels are

selected.

If in US mode, pressing and holding the WX/INT key for 2 seconds will

select Canadian channels (CAN will illuminate).

If in Canadian mode and WX/INT is pressed for 2 seconds, INT will

display and International channels are selected.

If WX/INT is pressed for 2 seconds while INT is illuminated, INT will

disappear and US channels are selected.

3.3.7 Transmitting

Press the Push-To-Talk key (PTT) and speak into the microphone using a

clear normal voice. If the current channel is a Weather Channel or a TX

prohibited channel, an alarm will sound when PTT is pressed indicating

such a transmission is not permitted.

As per FCC rules, if PTT is pressed and held enabling the transmitter

continuously for 5 minutes, the RAY215 will automatically disable the

transmitter. Once PTT is released, the transmitter will be re-enabled.

3.3.8 Selecting a Weather Channel

The US National Oceanic and Atmospheric Administration (NOAA)

broadcasts continuous weather reports and severe weather alerts, as needed.

The RAY215 is programmed to receive 10 NOAA weather channels and

sound an alarm if a weather alert is received.

The Weather Channels consist of Channel 0 through Channel 9. Press the

WX/INT key once to enter the Weather mode and use either the Channel

Select (CH) knob or Channel UP/DOWN Trackpad on the microphone to

select the desired weather channel. While the Weather Channel is active,

the WX indicator appears in the LCD display.

Note: Weather operation is available only in US frequency mode and

can only be heard in the US and Canada.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-10

Operation with a Fist Microphone

3.3.9 Priority Channel

Either channel 16 or 9 can be programmed as the Priority Channel.

To switch to the currently programmed Priority Channel at any time, press

the 16/9 key once.

To change the Priority Channel , press the 16/9 key once to switch to the

Priority Channel, then press and hold the 16/9 key until a tone is heard.

When the Priority Channel is active, a "P" appears in the small character

display.

3.3.10 Desensitized Reception (Local Mode)

You can set the RAY215 to reduce the receiving sensitivity in high traffic

areas to decrease unwanted reception. This is also known as local mode.

To select this mode, press and release the D/L key. While the desensitize

function (local mode) is active, the DESENS indicator appears in the LCD

display. To return to full receiver sensitivity (distant mode), again press

and release the D/L key.

3.3.11 Channel Memory

The RAY215 can store any US, Canadian, or International Channel. The

stored channels are the ones scanned in the Memory Scan mode.

To store a channel in memory, select the desired channel with the CH

knob and press and hold the SCAN/MEM key for 2 seconds.Atone sounds

and the MEM indicator is displayed. (Weather channels can not be stored

into memory).

To clear a channel from memory, select the memory channel and press

and hold the SCAN/MEM key for 2 seconds. The MEM indicator

extinguishes, indicating that channel is no longer stored in memory.

3.3.12 Resetting Factory Defaults

You can reset many radio settings back to their factory defaults:

• Erase any channels stored in memory for the Memory Scan function

• Erase any MMSI numbers stored in the base station for Individual Ship's

Call

• Turn OFF the backlight on the base station and Full Function Handset

• Return to US channels, if INT or CAN are selected

• Return the Weather Channel to channel 0

• Return the Priority channel to channel 16

Download from Www.Somanuals.com. All Manuals Search And Download.

3-11

Operation with a Fist Microphone

This will NOT erase the Own Ship's MMSI ID number for your vessel

nor will it erase the PHNBOOK entries made with the Full Function

Handset.

To perform the memory reset:

1. Turn the radio OFF.

2. Press and hold the SCAN/MEM key.

3. While continuing to hold the SCAN/MEM key, turn the radio ON.

The LCD remains blank for 2 seconds, CL appears momentarily, then

the unit switches to channel 16.

3.3.13 Scan Modes

The RAY215 is equipped with two types of scan options: All Scan and

Memory Scan. How these options are initiated is dependent upon whether

there are any channels stored in memory. Channel 70 is also monitored

during Scan mode.

All Scan Mode

If no channels are stored in memory when the SCAN/MEM key is pressed,

the radio begins scanning all channels (except weather channels) as long

as no signal is received. If a signal is received, the scan stops on the

receiving channel as long as it is present. If the signal is lost for five

seconds, the radio resumes scanning. SCAN is displayed on the LCD

while the Scan mode is active.

If the SCAN/MEM key is pressed again while SCAN is flashing, the All

Scan Standby state is suspended and the unit returns to the normal state.

To cancel the scan mode, press the SCAN/MEM key once.

Memory Scan Mode

If one or more channels are stored in memory when the SCAN/MEM key

is pressed, SCAN and MEM begin to flash simultaneously on the LCD. If

no other key is pressed within three seconds, SCAN and MEM stop

flashing and the radio begins scanning all channels currently stored in

memory. As with All Scan, if a signal is received, the scan stops on the

receiving channel until the signal is lost for five seconds, then the radio

resumes scanning. To cancel memory scan, press and release SCAN/MEM.

If there are channels stored in memory but All Scan operation is desired,

press SCAN/MEM again within the 3 second period while the SCAN and

MEM indicators are flashing.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-12

Operation with a Fist Microphone

3.3.14 Monitor Mode

The RAY215 is equipped with 2 types of monitor operations: Dual Watch

and Tri-Watch.

Dual Watch Mode

Dual Watch monitors the selected working channel and the programmed

Priority Channel. To initiate Dual Watch, first select the working channel

to be monitored, then press the MON/1/25 key once. The selected working

channel and the Priority channel (16 or 9) are monitored for traffic.

If a signal is received on the working or Priority channel, the radio monitors

that channel as long as a signal is present. Dual Watch will resume if the

signal is lost for 3 seconds. To exit the Dual Watch mode, press the MON/

1/25 key to revert to the last used working channel or the 16/9 key to

revert to the programmed Priority channel.

Tri-Watch Mode

Tri-Watch monitors the selected working channel, the programmed Priority

Channel, and the last used Weather Channel for the Weather Alert Tone.

To initiate Tri-Watch, initiate the Dual Watch mode and press the WX/

INT key. The WX indicator illuminates on the LCD to indicate the Weather

Channel is also being monitored.

Operation is the same as Dual Watch except that if a Weather Alert Tone

is received, the radio simultaneously sounds an alarm tone, WX flashes,

and the NOAA Weather Alert is monitored.

To exit the Tri-Watch mode, press the MON/1/25 key to switch to the last

used working channel or the 16/9 key to switch to the programmed Priority

channel. To revert to Dual Watch mode, press the WX/INT key.

3.3.15 LCD Backlight Function

Pressing this key twice starts Dimmer mode, which adjusts the brightness

of LCD's backlight. Each successive press of the DIM key switches the

brightness from Off, to Low, to Medium, to High, then back to Off.

After the key has not been pressed for 5 consecutive seconds, the currently

selected brightness level is stored in memory.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-13

Operation with a Fist Microphone

3.3.16 NMEA Operation

The RAY215 can receive valid position and time information, which are

transmitted during a DSC Distress call. This data can be communicated

via NMEA 0183 from a GPS, fishfinder, radar, or any device that outputs

GPS sentences. If the radio does not detect the positional data, it provides

different alerts urging you to find and correct the fault. The optional Full

Function Handset enables you to manually input this data using the L/L

ENT function, as described in Section 4.5.3.2.

If a GPS device is not connected via NMEA, the radio emits a 5-second-

long staccato alert tone and flashes the NMEA indicator 2 minutes after

power up. This occurs every time the unit is turned on. The alarm is required

by safety regulations and cannot be disabled.

Operation at Power Up

At power up, the radio monitors the NMEA line for 1 minute. If a signal

is detected on NMEA, the radio determines whether the data is valid. If

valid, the data is input, the NMEA indicator is displayed on handsets, and

the radio enters normal operation mode.

If no GPS signal is detected on NMEA after the 1 minute monitoring

period, a 5-second-long staccato alert tone is emitted and the NMEA

indicator flashes. All the position fields are set to 9’s and the time and

date fields are set to 8’s. The message NO GPS appears in the NAVSTAT

screen, although no positional data is displayed.

If at a later time valid data is received on NMEA, the data is input, the

NMEA indicator is displayed solid (no longer flashing), and the radio

enters normal operation mode.

Operation When the Signal is Lost or Becomes Invalid

If positional data that was previously detected becomes invalid or is no

longer detected, the radio monitors the NMEA line for 1 minute for it to

be restored.

If a signal is restored on the NMEA line and the radio determines the data

is valid, the data is input, the NMEA indicator remains illuminated, and

the radio re-enters normal operation mode.

However, if no signal is detected, the NMEA indicator flashes and a 5-

second-long staccato alert tone is emitted. The last received positional

data is retained in memory and can be viewed in the NAVSTAT screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-14

Operation with a Fist Microphone

The message NO GPS appears in NAVSTAT in the position where the

type of device used to be. The NMEA indicator continues to flash until

valid positional data is received. If valid positional data (from the same

source) is later restored, the NMEA indicator is again displayed solid.

Operation When No Signal Detected for 4 Hours

If no valid positional data is received or input manually within 4 hours of

the previous alert, the NMEA indicator continues to flash and the staccato

alert tone is again emitted. This pattern is repeated every 4 hours if no

positional data has been detected. If no manual input was made during

the previous 23.5 hours, all the position fields are set to 9’s and the time

and date fields are set to 8’s.

3.3.17 Digital Selective Calling (DSC)

The Digital Selective Calling (DSC) protocol is a globally applied system

used to send and receive digital Distress calls as well as Individual and

All Ships calls on channel 70, the dedicated DSC channel for Marine

VHF. For a Distress call transmission, your RAY215 takes the position

and time information from the input NMEA data along with your Maritime

Mobile Station Identifier (MMSI) and converts it into a digital "packet".

When transmitted, this digital information lets other ships and shore

stations know where you are and that you are in a Distress situation.

Communications in DSC mode include the following:

1. Transmitting/Receiving an Individual Call

2. Transmitting/Receiving an All Ships Call

3. Transmitting/Receiving a Distress Call (without designating type)

4. Receiving a Distress Relay Call (without designating type)

Individual, All Ships and Group DSC calls come in three varieties:

ROUTINE for normal calls, SAFETY for advisory alerts, and URGENCY

for assistance when life is not in immediate danger. To enable DSC mode,

press and release the DSC/PRI and D/L/ I.C. keys simultaneously. The

DSC indicator illuminates and a tone sounds. Since the Distress Call

(enabled by pressing and holding the Distress Key for 4 consecutive

seconds) automatically selects the DSC mode, it is not necessary to press

the DSC/PRI and D/L / I.C. to make a distress call.

When a DSC call is received, the radio automatically enters DSC mode if

you are currently on a selected working channel, in the Monitor mode, or

in the Scan mode. You will not receive a DSC call if the radio is transmitting

or receiving a non-DSC call.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-15

Operation with a Fist Microphone

Note: You must program the ship's MMSI number before the radio can

enter the DSC mode. See Section 3.3.17.1 below.

3.3.17.1 MMSI Number Setup

You must enter your Maritime Mobile Service Identity (MMSI) number

in the RAY215 before the DSC system will be operational. You can request

an MMSI number from the FCC when you apply for a radio license.

If your vessel does not require a license, you may obtain an MMSI by

contacting either BoatUS (www.boatus.com) or MariTEL

(www.maritelusa.com).

Once you have received your MMSI number, enter it into the radio as

follows:

1. Press and hold the DSC/PRI and D/L / I.C. keys simultaneously for 2

seconds to enter DSC mode.Atone sounds, the DSC indicator appears,

"0" is displayed in the large character display, and "1" is displayed in

the small character display.

Note: If an MMSI number is already in memory, the MMSI entry

scrolls across the display, one digit at a time.

3. Rotate the Channel Select (CH) knob until the first digit of your MMSI

number appears in the large character display. (Channel UP/DOWN

keys on the microphone are disabled during this process).

4. Press the DSC/PRI key once to accept. The small character display

now shows a "2", designating the second digit in your MMSI number.

5. Rotate the Channel Select (CH) knob until the second digit of your

MMSI number appears in the large channel display.

6. Press the DSC/PRI key once to accept.

7. Enter all 9 digits of the MMSI number in the same way.

Once the 9th digit has been entered and accepted, the RAY215 plays

back the 9 digits (one digit at a time) just entered for proper entry

verification.

Note: Ensure the MMSI number entered is correct with this

verification playback. Once the number is accepted as outlined in

the next step, it cannot be changed except by Raymarine factory

representatives.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-16

Operation with a Fist Microphone

8. If the number is verified as correct, press and hold the DSC/PRI key

for 2 seconds and a tone sounds. Your MMSI number has now been

stored in memory.

If the number is incorrect, press the DSC/PRI key once and release.

The radio will revert to the beginning of the entry process to start over

again. This step can be repeated as many times as required until the

number is entered correctly.

PRESS & HOLD

DSC + D/L

MMSI digit digit position

ROTATE

PRESS & REL

DSC

Select desired digit

Next digit position

Select desired digit

PRESS & REL

DSC

ROTATE

PRESS & REL

DSC

Radio replays all digits...

Continue thru last digit position

Select desired digit

PRESS & HOLD

DSC

MMSI number accepted

Returns to working channel

...through the 9th position

PRESS & REL

DSC

Returns to first digit position

3.3.17.2 Individual Ship's Call

An Individual Ship's Call is a DSC call made to a specific ship identified

by its MMSI number. There are three types: ROUTINE for normal calls,

SAFETY for advisory alerts, and URGENCY for assistance when life is

not in immediate danger.

The RAY215 can receive all three types of Individual calls but can only

transmit ROUTINE Individual calls. As with any DSC operation, the call

is made on channel 70.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-17

Operation with a Fist Microphone

Sending an Individual Ship's Call

The RAY215 can only send a Routine Individual Call. The MMSI number

of the ship to which the Individual Call is to be sent can be input manually

or selected from a phonebook listing in memory. This section includes

instructions for using both methods and for adding numbers to the

phonebook.

Using a manually input MMSI number

1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to

place the unit in DSC mode. "70" appears in the large channel display,

the DSC indicator illuminates, and "in" appears in the small channel

display to designate individual call.

2. Press and release the DSC/PRI key. The DSC indicator appears, "0" is

displayed in the large character display, and "1" is displayed in the

small character display.

3. Rotate the Channel Select (CH) knob until the first digit of your MMSI

number appears in the large character display. (Channel UP/DOWN

keys on the microphone are disabled during this process).

4. Press the DSC/PRI key once to accept. The small character display

now shows a "2", designating the second digit in the other ship’s MMSI

number.

5. Rotate the Channel Select (CH) knob until the second digit of the

other ship’s MMSI number appears in the large channel display.

6. Press the DSC/PRI key once to accept.

7. Enter all 9 digits of the MMSI number in the same way.

8. Once the 9th digit has been entered and accepted, the RAY215 plays

back the 9 digits just entered for proper entry verification.

If the number is incorrect, press the DSC/PRI key once and release.

The radio will revert to the beginning of the entry process to start over

again. This step can be repeated as many times as required until the

number is entered correctly.

9. When the MMSI number is verified as correct, press and hold the

DSC/PRI key for 2 seconds to verify.

Note: The operation is cancelled if the 16/9 key is pressed or if no keys

are pressed for 60 seconds during any part of this process.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-18

Operation with a Fist Microphone

PRESS & REL

DSC + D/L

PRESS & REL

DSC

Radio enters DSC mode

MMSI digit digit position

ROTATE

PRESS & REL

DSC

Select desired digit

Next digit position

Select desired digit

PRESS & RELEASE

PRESS & REL

ROTATE

DSC

Continue thru last digit position

Select desired digit

Radio replays all digits through the 9th position

PRESS & RELEASE

DSC

Process starts over

PRESS & HOLD

DSC

MMSI number accepted

...through the 9th position

Radio replays all digits...

10. After you have selected the other ship's MMSI number, the radio

prompts you for the working channel you wish to communicate on.

The large character display shows the last used channel number and a

"W" appears in the small channel display. Using the Channel Select

(CH) knob on the front panel, select the desired working channel for

the Individual Call.

11. Press the DSC/PRI key once. The TX indicator on the LCD flashes,

indicating the RAY215 is ready to transmit.

12. Press the PTT key to send the digital "packet" of information. The

radio waits for an acknowledgment from the targeted ship or station.

13. If the target station acknowledges, a tone sounds and "ACK" illuminates

on the LCD. After 2 seconds, the RAY215 switches to the previously

selected working channel.

If the call is not acknowledged, exit the DSC mode by pressing the 16/

9 key.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-19

Operation with a Fist Microphone

ROTATE

PRESS & REL

PRESS & HOLD

DSC

[TX] Flashing

Select desired working channel

Returns to last used channel

PRESS

PTT

"ACK" signal received

from the specified ship

2 seconds after receiving ACK,

switches to selected channel

Standby for "ACK"

from specified ship

Using an MMSI number selected from the phonebook:

Using the RAY215 with a fist microphone, you can select from up to ten

other ship's MMSI numbers that have been stored in the phonebook. The

numbers are identified by a single letter that you have assigned to it. You

must note what letter you assigned to the MMSI number because only

that letter appears on the LCD when you are retrieving it.

Note: The operation is cancelled if the 16/9 key is pressed or if no keys

are pressed for 60 seconds during any part of this process.

1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to

place the unit in DSC mode. "70" appears in the large channel display,

the DSC indicator illuminates, and "in" appears in the small channel

display to designate Individual Call.

2. Press and release the SCAN/MEM key. A letter appears in the small

channel display, which is associated with one of the other ship's MMSI

numbers in the phonebook.

3. If you wish to use the use the other ship's MMSI number associated

with this letter, press DSC/PRI.

4. To use a different letter, rotate the Channel Selection Knob until the

desired letter is displayed. Press DSC/PRI to select this letter.

5. After you have selected the other ship's MMSI number, the radio

prompts you for the working channel to communicate on. The large

character display shows the last used channel number and a "W"

appears in the small channel display.

6. Using the Channel Select (CH) knob on the front panel, select the

desired channel, and press the DSC/PRI key once. The TX indicator

on the LCD flashes, indicating the RAY215 is ready to transmit.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-20

Operation with a Fist Microphone

7. Press the PTT key to send the Individual Ship's Call. After the digital

"packet" of information is sent, the radio waits for an acknowledgment

from the targeted ship or station.

8. If the target station acknowledges, a tone sounds and "ACK"

illuminates on the LCD. After 2 seconds, the RAY215 switches to the

previously selected working channel.

If the call is not acknowledged, exit the DSC mode by pressing 16/9.

Note: The operation is cancelled if the 16/9 key is pressed or if no keys

are pressed for 60 seconds during any part of this process.

PRESS & REL

DSC + D/L

PRESS & REL

SCAN

Radio enters DSC mode

PRESS & REL

DSC

ROTATE

Returns to last used channel

Select working channel

Select letter assigned to desired MMSI

PRESS

DSC

PTT

[TX] Flashing

Standby for ACK from specified ship

ACK received from specified ship

2 seconds after receiving ACK,

switches to selected channel

To store an MMSI number in phonebook:

1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to

place the unit in DSC mode. "70" appears in the large channel display,

the DSC indicator illuminates, and "in" appears in the small channel

display to designate individual call.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-21

Operation with a Fist Microphone

2. Press and release the DSC/PRI key. The DSC indicator appears, "0" is

displayed in the large character display, and "1" is displayed in the

small character display.

3. Rotate the Channel Select (CH) knob until the first digit of your MMSI

number appears in the large character display. (Channel UP/DOWN

keys on the microphone are disabled during this process).

4. Press the DSC/PRI key once to accept. The small character display

now shows a "2", designating the second digit in your MMSI number.

5. Rotate the Channel Select (CH) knob until the second digit of your

MMSI number appears in the large channel display.

6. Press the DSC/PRI key once to accept.

7. Enter all 9 digits of the MMSI number in the same way.

Note: The operation is cancelled if the 16/9 key is pressed or if no keys

are pressed for 60 seconds during any part of this process.

8. Once the 9th digit has been entered and accepted, the RAY215 plays

back the 9 digits just entered for proper entry verification.

If the number is incorrect, press the DSC/PRI key once and release.

The radio will revert to the beginning of the entry process to start over

again. This step can be repeated as many times as required until the

number is entered correctly.

9. When the MMSI number is verified as correct, press the SCAN/MEM

key. A letter appears in the small channel display.

10. If you wish to assign this letter to the Other Ship's MMSI, press DSC/

PRI.

11. If you wish to assign a different letter to the Other Ship's MMSI,

rotate the Channel Selection Knob until the desired letter is displayed.

12. Press DSC/PRI to store the MMSI number/letter assignment into the

phonebook.

Up to ten Other Ship's numbers can be stored in the phonebook. The

letters available are as follows:

Download from Www.Somanuals.com. All Manuals Search And Download.

3-22

Operation with a Fist Microphone

You must note what letter you assigned to the MMSI number because

only that letter appears on the LCD when you are retrieving it.

Note: No data is stored in memory when a wrong key operation or an

interruption of power occurs during the entry procedure.The operation

is cancelled if the 16/9 key is pressed or if no keys are pressed for 60

seconds during any part of this process.

PRESS & REL

DSC

DSC + D/L

Radio enters DSC mode

MMSI digit digit position

ROTATE

PRESS & REL

DSC

Select desired digit

Next digit position

Select desired digit

PRESS & RELEASE

PRESS & REL

ROTATE

DSC

Continue thru last digit position

Select desired digit

Radio replays all digits through the 9th position

PRESS & RELEASE

If incorrect, start over

DSC

PRESS & RELEASE

SCAN

If correct, assign letter

...through the 9th position

Radio replays all digits...

ROTATE

PRESS & REL

DSC

Select letter assigned to this MMSI number

MMSI number / letter accepted

To delete an MMSI number from the phonebook:

1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously.

2. Press and release the SCAN/MEM key.

3. Rotate the Channel Selection Knob until the letter representing the

MMSI number to be deleted is displayed.

4. Press and hold D/L/I.C. The selected number is deleted from the

phonebook and the radio switches to channel 16.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-23

Operation with a Fist Microphone

Receiving an Individual Ship's Call

When an Individual Ship's Call is received, the radio automatically enters

DSC mode if you are currently on a selected working channel, in the

Monitor mode, or in the Scan mode.

If a received signal is confirmed to be addressed to your own station, an

acknowledging signal is sent back. If the received signal is not addressed

to your own station, the unit remains in its previous mode without sending

an acknowledging signal.

When receiving Individual Ship's Call

1. If your station is targeted for an Individual Ship's Call, a tone sounds

and the unit automatically switches to DSC mode. TX flashes on the

LCD and one of the following categories of Individual Ship's Calls

flashes in the small number display:

"Ir" for ROUTINE Individual Ship's Call

"IS" for SAFETY Individual Ship's Call

"IU" for URGENCY Individual Ship's Call

2. To acknowledge the incoming Individual Ship's Call, press the PTT

key. The acknowledge is transmitted and your RAY215 automatically

selects the working channel specified by the originating ship or station.

3. If you do not wish to acknowledge the call, press the 16/9 key to exit

the DSC mode.

PRESS & RELEASE

PTT

PRESS & RELEASE

16/9

Acknowleging the call

Receive Individual Ship's Call:

Routine, Safety, or Urgency

Not acknowleging the call

Download from Www.Somanuals.com. All Manuals Search And Download.

3-24

Operation with a Fist Microphone

3.3.17.3 All Ships Call

The All Ships Call is used to send out a message to all ships in range that

you need assistance but the situation is not serious enough for a Distress

Call. This call should only be used if hailing for assistance on channel 9

or 16 fails. There are three types ofAll Ships Calls: ROUTINE for normal

calls, SAFETY for advisory alerts, and URGENCY for assistance when

life is not in immediate danger. The RAY215 can transmit and receive all

three types of these calls. As with any DSC operation, the call is made on

channel 70. Then, after the All Ships Call is sent or received, the radio

automatically selects channel 16.

Sending an All Ships Call

1. Press and release the DSC/PRI and D/L / I.C. keys simultaneously to

enter the DSC mode.

2. Rotate the Channel Select (CH) knob on the front panel to select the

desired type of call. The following appears in the small channel display:

"Ar" for ROUTINE All Ships Call

"AS" for SAFETY All Ships Call

"AU" for URGENCY All Ships Call

3. Press and release the DSC/PRI key and TX begins to flash.

4. Press the PTT key to transmit theAll Ships Call. The radio switches to

Channel 16.

5. Any station responding to your call converses on Channel 16.

PRESS & REL

ROTATE

DSC + D/L

PRESS & REL

DSC

PTT

Download from Www.Somanuals.com. All Manuals Search And Download.

3-25

Operation with a Fist Microphone

Receiving an All Ships Call

If you are currently on a selected working channel, in the Monitor mode,

or in the Scan mode, the radio automatically enters DSC mode when an

All Ships Call is received. The type of call is displayed in the small channel

display and an alarm is sounded.

Press the DSC/PRI key once and the radio automatically selects channel

16. There is no acknowledge required for an All Ships Call. If you do not

wish to accept the call, press the 16/9 key to exit the DSC mode.

PRESS & RELEASE

DSC

Converse on channel 16

Receive All Ships Call:

Routine, Safety, or Urgency

3.3.17.4 Group Call

The Group Call feature sends transmissions that are only received by

radios that share a common Group MMSI number.

The RAY215 requires an optional Full Function Handset to program in

the Group MMSI number. For this reason, a RAY215 equipped with only

a Fist Microphone cannot send or receive Group Calls.

If you have used an optional Full Function Handset to program in the

Group MMSI number, you may use a RAY215 equipped with a Fist

Microphone to receive Group Calls, even if the Full Function Handset is

no longer attached. However, you cannot send Group Calls without the

Full Function Handset.

If you are currently on a selected working channel, in the Monitor mode,

or in the Scan mode when a Group Call is received, the radio automatically

enters DSC mode, sounds an alarm, and displays the type of call as follows:

"Gr" for ROUTINE Group Call

"GS" for SAFETY Group Call

"GU" for URGENCY Group Call

Download from Www.Somanuals.com. All Manuals Search And Download.

3-26

Operation with a Fist Microphone

As with any DSC operation, the call is made on channel 70. If a received

signal is confirmed to be addressed to the group that your station belongs

to, the radio switches to DSC receiving mode and does not send back an

acknowledgment. If the received signal is not addressed to the group that

your station belongs to, the unit returns to the mode before receiving the

Group Call.

After receiving a Group Call, press and release the DSC key to accept the

call. The unit switches to channel 16 and extinguishes the DSC indicator,

indicating the unit has exited the DSC mode.

The large channel display indicates the working channel and the small

channel display is extinguished. If you do not wish to acknowledge the

call, press the 16/9 key to exit the DSC mode.

PRESS & RELEASE

DSC

Call accepted.

Converse on channel 16.

Receive Group Call:

Routine, Safety, or Urgency

3.3.17.5 Distress Call

A Distress Call allows you to send out a digital "packet" of data at high

power that includes your position, time, and MMSI number.All ships and

stations outfitted with the correct type of DSC equipment will be able to

pinpoint your position and either relay the information or respond directly.

Using the Distress key overrides all other functions.

Sending a Distress Call

1. On the back of the microphone, lift the door marked DISTRESS.

2. Press and hold the red Distress key for 5 seconds. After 1 second, the

LCD displays a countdown from four to zero, beeping every second.

3. When the countdown has completed, the radio enters the DSC mode,

sounds a loud alarm, and sends the digital information at high power.

Once transmitted, the radio monitors channel 70 for a Distress

acknowledge but also monitors channel 16 for emergency traffic.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-27

Operation with a Fist Microphone

Note: When a Distress Call is sent, the unit emits a VERY LOUD

distress alarm tone. To mute the alarm without interrupting the Distress

Call, press the DSC/PRI key on the RAY215 base station. The radio

will remain in DSC mode.

4. The Distress Call is automatically re-transmitted every 3.5 to 4 minutes

as long as you remain in DSC mode. The radio continues to transmit

until either an acknowledge is received or the DSC mode is manually

exited by pressing the 16/9 key. The ACK indicator flashes, indicating

the radio is monitoring for an acknowledge.

5. If a receiving station has Distress acknowledge capability and sends

an acknowledge to you, the DSC tone sounds and the ACK indicator

appears solid for 1 second. Next, the radio exits the DSC mode and

switches to channel 16 for voice communications.

PRESS & HOLD

DISTRESS

PRESS & HOLD

DISTRESS

Hold DISTRESS for full 5 seconds

After 1 sec, countdown begins

Distress call transmitted

Acknowledge signal received

Waiting for Acknowledge

Switches to Channel 16

Receiving a Distress Call

When a DSC Distress call is received, the radio automatically enters DSC

mode if you are currently on a selected working channel, in the Monitor

mode, or in the Scan mode. You will not receive a DSC call if the radio is

transmitting or receiving a non-DSC call.

1. When receiving a Distress Call signal, the unit sounds an alarm tone

and enters the DSC mode. A "d" flashes in the small channel display

for Distress.

2. Press the DSC/PRI key. The radio accepts the call, silences the alarm,

and switches to channel 16.

Download from Www.Somanuals.com. All Manuals Search And Download.

3-28

Operation with a Fist Microphone

Note: When a Distress Call is received, the unit emits a VERY LOUD

distress alarm tone. Pressing the DSC/PRI key on the base station

mutes this alarm but does NOT cancel the Distress Call.

3. The RAY215 does not have the ability to acknowledge or relay a DSC

Distress Call so once the Distress Call is received, you should attempt

to contact the vessel in distress on channel 16 and attempt to render

assistance.

PRESS & RELEASE

DSC

Switch to Channel 16

Distress Call received

3.3.17.6 Distress Relay Call

Sometimes a ship’s distress call can be relayed from another ship or a

shore station. The RAY215 can only receive a Relayed Distress call; it

cannot initiate one.

If the radio is active on a working channel, in the Monitor mode or in the

Scan mode when a Distress Relay Call is received, the unit automatically

enters DSC mode and emits an alarm tone. The DSC indicator illuminates,

70 is indicated on the large channel display, and "dr" flashes on the small

channel display.

Press and release DSC/PRI. The unit switches to channel 16. "16" appears

as the working channel on the large channel display while the small channel

display is extinguished. The DSC indicator is also extinguished, indicating

the unit has exited the DSC mode.

Note: When a Distress Call is received, the unit emits a VERY LOUD

distress alarm tone. Pressing the DSC/PRI key on the base station mutes

this alarm but does NOT cancel the Distress Call.

The alert tone continues to sound until DSC/PRI is pressed to accept the

call or 16/9 is pressed to exit the DSC mode.

PRESS & RELEASE

DSC

Switch to Channel 16

Distress Relay Call received

Download from Www.Somanuals.com. All Manuals Search And Download.

4-1

Operation with a Full Function Handset

Section 4 Operation with Optional

Full Function Handset

4.1 Introduction

The RAY215 can be operated with the standard Fist Microphone, or an

optional Full Function Handset that enables additional features, or both

handsets to enable intercom capabilities. This section describes using the

RAY215 with the optional Full Function Handset. See Section 3 for operation

using the standard Fist Microphone.

The Full Function Handset provides you with these additional features:

• Full alphanumeric keypad

• Dedicated keys for Individual andAll Ships DSC calls

• DSC distress calls that describe the type of distress

• Send and receive DSC Group Calls

• Expanded ship and shore phonebooks for making DSC Individual calls

• Manually enter lat/lon and UTC time when GPS input is not available

• DSC Call Log

The Full Function Handset option is available as a Single Station (Raymarine

part number E46019) that replaces the fist microphone or as a Dual Station

(Raymarine part number E46021) that, when used in conjunction with a

Fist Microphone, enables intercom functions between the two stations.

The optional Full Function Handset connects to the port labeled

HANDSET/RELOCATION KIT on the rear of the base station. The handset

will not operate if connected to the microphone port on the front of the

base station. If both a Fist Microphone and Full Function Handset are to

be used, the Fist Microphone must be connected to the front microphone

port and the Full Function Handset connected to the HANDSET/

RELOCATION KIT port on the rear of the base station.

4.1.1 Microphone / Full Function Handset Priority

When both a Fist Microphone and Full Function Handset are in use, only

one can have priority to make a call. When the Full Function Handset is

out of its cradle, it has priority over the Fist Microphone and the REMOTE

indicator illuminates on the LCD of the base station. When the Full Function

Handset is in the cradle, the Fist Microphone has priority and the REMOTE

indicator extinguishes.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-2

Operation with a Full Function Handset

In an emergency, the base station can override the Full Function Handset

to make a call even though the handset has priority (is off the cradle). To

override the handset, press and hold the DSC/PRI key on the base station.

The REMOTE indicator flashes and the base station regains priority control.

Make your call as usual using the Fist Microphone. On the Full Function

Handset, OVERRIDE appears on the dot matrix display. In this mode, all

keys are disabled on the handset except for DISTRESS. The base station

retains control until the DSC/PRI key is again pressed and held.

Note: The RAY215 is designed to have the base station as the priority

unit. You should install the base station and Fist Microphone in the

radio room or the location from which the ship is normally navigated. If

an optional second station Full Function Handset is also installed, that

handset is the one that should be installed in the remote location.

4.1.2 Handset Connections

The Full Function Handset connects to the port labeled HANDSET/

RELOCATION KIT on the rear of the base station (Figure 4-1). The Full

Function Handset will not operate if connected to the port on the front of

the base station.

If both a Fist Microphone and Second Station Full Function Handset are

to be used, the Fist Microphone must be connected to the front port with

the Full Function Handset connected to the HANDSET/RELOCATION

KIT port on the rear. In this case, the Handset Relocation Kit could not be

used with the Fist Microphone. Once installed, the two stations can

communicate with one another using the Intercom function described in

section 4.4.12.

Figure 4-1 Rear Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

4-3

Operation with a Full Function Handset

4.2 Controls and LCD Display

Figure 4-2 Layout of Controls

4.2.1 Controls

This section describes the control buttons and display messages that

appear on the Full Function Handset.

Note: This Full Function Handset is also used with Raymarine radios

that have additional features. As a result, the yellow Function labels

POWER (16/9 key), CELL (3 key), HAIL (* key), and FOG (# key)

represent features that are not available on the RAY215.

INDV key

Switches to the DSC Individual Ships Call mode for initiating selective

calls (ship-to-ship, group calls, etc.) using a specific MMSI number.

Descriptions of these operations appear below in sections 4.4.16.1

and 4.4.16.2.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-4

Operation with a Full Function Handset

Note: An MMSI number is required to operate the DSC equipment in

this radio. You can program the MMSI number yourself one time

only using the Menu Operation described in section 4.5.4 or you

can have your Raymarine dealer program the number for you.

ALL SHIP key

Switches to the All Ships Call mode for Safety and Urgency

transmissions. Descriptions of subsequent operations appear below

in section 4.4.16.6 TransmittingAll Ships Call.

VOL UP/DOWN key

Changes the sound volume of the handset. Pressing the UP ∧∧∧ key

∧∧

increases the volume, while the DOWN ∨∨∨key causes it to decrease.

The number of segments in the VOL bar graph on the LCD display

will increase or decrease accordingly.

SQ UP/DOWN (SCROLL) key

Increases or decreases the squelch sensitivity. Pressing the UP ∧∧∧

key increases the squelch, while the DOWN ∨∨∨key decreases it. The

number of segments in the SQ bar graph on the LCD display will

increase or decrease accordingly. This key is also used as a scroll key

for selecting menu items and other settings, as described below.

16/9 key

Switches between the Working Channel and the Priority Channel.

Pressing and holding the key for 2 seconds alternates the Priority

Channel between channel 9 and channel 16.

Note: The POWER label over this key does not pertain to the RAY215.

MON/TRI key

Starts the Dual-Watch monitor mode. Pressing the FUNC key followed

by the MON/TRI key initiates the Tri-Watch monitor mode.

1/MEM key

This key inputs the number 1. When an alphanumeric response is

appropriate, this key alternates between entering a 1 and a space. If

the channel number indicated on the LCD display is not currently

stored in memory, pressing the FUNC key followed by the 1/MEM

key enters that channel number into memory. If the currently indicated

channel has already been stored, pressing the FUNC key followed by

the 1/MEM key deletes that channel from memory.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-5

Operation with a Full Function Handset

2/SCAN key

This key inputs the number 2. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 2,

A, B, then C. Pressing the FUNC key followed by the 2/SCAN key

toggles Scan mode ON or OFF. Scan mode is described below in

section 4.4.13.

3 key

This key inputs the number 3. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 3,

D, E, then F.

Note: The CELL label over this key does not pertain to the RAY215.

4/INT key

This key inputs the number 4. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 4,

G, H, then I. Pressing the FUNC key followed by the 4/INTkey alternates

the frequency groups from US mode to International mode to Canadian

mode.

5 key

This key inputs the number 5. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 5,

J, K, then L.

6/WX key

This key inputs the number 6. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 6,

M, N, then O. Pressing the FUNC key followed by the 6/WX key

alternates between the Working Channel and the Weather Channel.

7/ D/L key

This key inputs the number 7. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 7,

P, Q, R, then S. Pressing the FUNC key followed by the 7/ D/L key

toggles between full receiver sensitivity (distant mode) and attenuated

receiver sensitivity (local mode). Local mode is used in high traffic

areas to decrease unwanted reception. While in local mode (receiver

is desensitized), the DESENS indicator appears in the LCD display.

8 key

This key inputs the number 8. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 8,

T, U, then V.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-6

Operation with a Full Function Handset

9/ 1/25 key

This key inputs the number 9. When an alphanumeric response is

appropriate, each press of this key alternately inputs the characters 9,

W, X, Y, and then Z. Pressing the FUNC key followed by the 9/ 1/25

key alternates the transmission power between 1W and 25W.

* key

This key inputs an asterisk (*).

Note: The HAIL label over this key does not pertain to the RAY215.

0/IC key

This key inputs the number 0. Pressing the FUNC key followed by the

0/IC key starts Intercom mode, which enables conversation between

the fist microphone connected to the port on the front of the base

station and a Full Function Handset connected to the to the port on

the rear of the base station. Pressing the FUNC key followed by this

key during Intercom mode returns operation to normal mode.

# key

This key inputs the # character.

Note: The FOG label over this key does not pertain to the RAY215.

ENT key

This key performs the Enter function. It is used to confirm and

implement an input action. Pressing the FUNC key followed by the

ENT/MENU key initiates the Menu mode.

CLR key

Depending on when it is used, this key exits the current mode and

reverts to the last used mode or normal operation. This key also can

be used to clear any alphanumeric inputs one at a time in the order

that they were entered. Pressing the FUNC key followed by CLR/LOG

key initiates the Digital Selective Calling (DSC) Log. Pressing the key

during logging returns operation to normal mode.

FUNC key

Initiates the Function mode and activates the FUNC indicator in the

LCD display. The next key pressed determines the function selected.

(See above key descriptions.) Pressing this key twice starts Dimmer

mode, which reduces the brightness of LCD's backlight.

Channel UP/ DOWN key

Pressing this key during normal operation changes the channel number

UP or DOWN.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-7

Operation with a Full Function Handset

PTT (Press-to-Talk) key

Pressing this key during normal operation places the radio in Transmit

mode and displays the TX indicator in the LCD. When the key is

pressed in various function modes, the assigned operation is initiated.

Note: After 5 minutes of continuously holding the PTT key, the radio

will automatically stop transmitting. To begin transmitting again,

release the PTT and depress again.

DISTRESS key

This key is located under the small door labeled DISTRESS on the

back of the handset. Pressing and holding this key for 5 seconds

selects Distress Signal Call mode. Subsequent operations are

described in section 4.4.16.8.

4.2.2 LCD Display

The following describes the functional characters on the RAY215

Handset's LCD.

Figure 4-3 LCD Display Layout

NMEA indicator

Displayed when the radio receives valid NMEA position data. If the

data is invalid or no data is received for a period of time, the indicator

disappears.

FUNC indicator

Displayed when the FUNC key is pressed. Disappears when another

key is pressed, or after no other key is pressed for a period of time.

WX indicator

Displayed while in Weather Channel mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-8

Operation with a Full Function Handset

TX indicator

Displayed while transmitting.

CAN indicator

Displayed when the Canadian frequency group is selected.

US indicator

Displayed when the US frequency group is selected.

INT indicator

Displayed when the International frequency group is selected.

1W indicator

Displayed when the transmission power of 1W is selected with the 9/

1/25 key or when a low power channel is selected.

DESENS indicator

Displayed during the desensitized receiving (local) mode.

MEM indicator

Displayed while the channel stored in memory is displayed. This

indicator flashes before the start of the memory scan operation.

SCAN indicator

Displayed during Scan mode. If channels have been stored in memory,

this indicator will be flashing before the start of Scan mode.

DSC indicator

Displayed when in a Digital Selective Calling (DSC) call mode, DSC

log, or the DSC menu.

VOL indicator (in bar graph)

Represents the current sound volume level of the handset. A louder

volume displays a larger number of segments in the bar graph. This

bar graph is not displayed during Menu mode.

SQL indicator (in bar graph)

Represents the current squelch level. A deeper squelch displays a

larger number of segments in the bar graph.

Three-digit, Seven-segment indicators

Display the channel number or state of the radio.

Nine-digit Dot-matrix display

Displays alphanumeric messages, modes, and functional status of

the radio.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-9

Operation with a Full Function Handset

4.3 Radio Functions

1. Selecting the Frequency Mode

Channel selection is available from among three frequency groups:

US, International, or Canadian.

2. Receiving the Weather Channels

The RAY215 is programmed to receive 10 NOAA weather channels

and will sound an alarm if a WeatherAlert is received.

3. Selecting the Priority Channel

Select Channel 16 or Channel 9 as the Priority Channel.

4. Dimmer Operation

Select from four LCD backlight levels, including OFF.

5. Monitor Operation

Select from Dual-Watch or Tri-Watch mode.

6. Scan Operation

Select fromAll Scan or Memory Scan.

7. Selecting Transmission Power Output

Select either 1W or 25W for the transmission power.

8. Digital Selective Calling (DSC) Operation

Conforms to the SC-101 standard for a VHF DSC radio. These functions

include Individual Ships Call,All Ships Call, Distress Call, Group Call,

and DSC logging capability.

Note: An MMSI number is required to operate the DSC equipment in

this radio. You can program the MMSI number yourself one time

only using the Menu Operation described in section 4.5.4 or you

can have your Raymarine dealer program the number for you.

9. NMEA Receiving Operation

Positional information from external equipment is obtained using the

NMEA 0183 interface.

10. Remote Operation

When both a Fist Microphone and Full Function Handset are

connected, the RAY215 can be controlled by either the handset or

microphone. When the handset is out of its cradle, it has priority over

the microphone. When the handset is in the cradle, the microphone

has priority and BASE appears on the handset’s LCD.

If you need to make a call with the fist microphone while the handset

is out of the cradle, press and hold the DSC/PRI key. The fist

microphone regains priority control and OVERRIDE appears on the

handset’s LCD.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-10

Operation with a Full Function Handset

11. Intercom Function between Handsets

Intercom mode enables conversation between a fist microphone

connected to the front of the base station and a Second Station Full

Function Handset connected to the to the rear of the base station.

12. Reduced Receiving Sensitivity (Local Mode)

This function decreases receiver sensitivity in high traffic areas to

decrease unwanted reception.

4.4 Operating Procedures

With the Full Function Handset, all operations can be made on the Handset

except turning ON/OFF the base station and adjusting the sound volume

of the External Speaker.

4.4.1 Setting the Volume

The sound volume adjustment for the handset has 11 settings. Pressing

and releasing the VOL UP∧∧∧key increases the volume by one level; pressing

and releasing the VOL DOWN ∨∨∨key reduces the volume by one level.

The number of segments in the VOL bar graph on the LCD display will

increase or decrease accordingly. If the VOL UP/DOWN keys are pressed

and held, the volume levels will automatically change every half-second.

Setting the Volume on the External Speaker

The volume knob on the External Speaker controls its sound volume.

Turning the knob clockwise increases the volume; turning it

counterclockwise reduces the volume. Turning the knob fully

counterclockwise until you hear a “click” switches off the speaker

completely.

When a DSC Distress Call is sent or received, an alarm is sounded on the

external speaker at maximum volume regardless of the volume set with the

knob, even if the knob has been rotated all the way OFF.

4.4.2 Setting the Squelch

The squelch adjustment enables you to “quiet” the receiver when no

signal is being received. The squelch adjustment for the handset has 11

∧∧

settings. Pressing and releasing the SQ UP ∧∧∧ key increases the squelch

∨∨

by one level; pressing and releasing the SQ DOWN ∨∨∨key decreases it by

one level. The number of segments in the SQ bar graph on the LCD display

will increase or decrease accordingly. If the SQ UP/DOWN keys are pressed

and held, the squelch levels will automatically change every half-second.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-11

Operation with a Full Function Handset

4.4.3 Using the Function Key

Most of the keys on the handset control multiple operations. Pressing one

of these keys after pressing the FUNC key initiates the operation marked

on the label above that key. When the FUNC key is pressed, the FUNC

indicator is displayed on the LCD display. If no other key is pressed for 5

seconds, the operation is cancelled and the FUNC indicator disappears.

4.4.4 Setting the Frequency Mode

Select the channel frequency group to be used: US, Canadian, or

International. Indicators displayed in the LCD identify the active frequency

group: US for the US frequency group, CAN for the Canadian group, and

INT for the International group.

Pressing the FUNC key followed by the INT key alternates the frequency

groups from US mode to International mode to Canadian mode then back

to US mode. When the radio is powered on, the radio is set to the last

selected Priority Channel (9 or 16) in the last selected frequency group .

When the frequency group is changed, the channel number remains the

same as was selected in the previous group, as long as that number is

present in the new group. If a channel number is absent in the destination

group, the new channel will be the previous number plus 1. When returning

to the previous frequency group, the channel returns to its original number

if the channel has not been changed. If the channel has been changed,

that number is retained when the frequency group is changed.

Example1

CH15 US ⇒ CH15 INT ⇒ CH15 CAN ⇒ CH15 US

When shifting the frequency group, the channel remains the same because

the corresponding channel number exists in the new frequency group.

Example2

CH2 CAN ⇒ CH3 US ⇒ CH2 INT ⇒ CH2 CAN

No corresponding channel exists in the new frequency group, so the

channel is incremented by 1.As long as the channel is not changed further,

it returns to its previous number if the frequency group is again changed.

Example3

CH2 CAN ⇒ CH3 US, then changed to CH5 ⇒ CH5 INT ⇒ CH5 CAN

However, if the channel is changed in the new frequency group, this new

number is retained when the frequency group is changed.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-12

Operation with a Full Function Handset

4.4.5 Receiving on the Weather Channels

The US National Oceanic and Atmospheric Administration (NOAA)

broadcasts continuous weather reports and severe weather alerts, as

needed. The RAY215 is programmed to receive 10 NOAAweather channels

and sound an alarm if a weather alert is received.

The Weather Channels consist of Channel 0 through Channel 9. To switch

between the Working Channel and the current Weather Channel, press the

FUNC key followed by the 6/WX key. While theWeather Channel is active,

the WX indicator appears in the LCD display and the frequency group

indicator disappears.

If the channel number is changed while in the Weather mode, the new

channel number is stored in memory upon exiting Weather mode. To exit

Weather Mode, press CLR, or FUNC followed by 6/WX.

Note: Weather operation is available only in US frequency mode and

can only be heard in the US and Canada.

4.4.6 Selecting the Channel

Two methods are available for selecting the channel: inputting the channel

with the numeric keypad then pressing the ENT key, or using the Channel

UP/DOWN key on the side of the handset. Both methods are applicable to

the three frequency groups on the Working Channel.

Using the Channel UP/DOWN Key

Pressing the Channel UP ∧∧∧key increments the current channel number by

one for each keyclick. When the highest channel number is reached, the

channel scrolls to the lowest number and increments from there. Pressing

∨∨

the Channel DOWN ∨∨∨ key decrements the current channel number by

one for each keyclick. When the lowest channel number is reached, the

channel scrolls to the highest number and decrements from there. Channel

numbers not available in a frequency group are skipped.

If the Channel UP/DOWN key is pressed and held for at least a half second,

channels automatically change every 100 milliseconds.

Using the Numeric Keypad

To select a channel, input the desired number on the keypad. For 5 seconds

the channel number flashes on the LCD display. If the ENT key is pressed

during this 5 second interval, the channel change is implemented.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-13

Operation with a Full Function Handset

If the 5 seconds elapse without pressing another key, the channel change

is implemented anyway. If the CLR key is pressed while the number is

flashing, the channel returns to the previous number.

Note: A leading zero is required for single digit channel numbers.

4.4.7 Priority Channel

The Priority Channel operates on either Channel 16 or Channel 9. Pressing

the 16/9 key during any operation except the Distress Call switches to the

Priority Channel. Pressing and holding the 16/9 key for 2 seconds alternates

the Priority Channel between Channel 16 and Channel 9.

While using the Priority Channel, pressing the 16/9 key or the CLR key

returns operation to the Working Channel.

4.4.8 Channel Memory

Channels that are stored in memory in the same group can be scanned

using the Memory Channel Scan function. Channels can be stored in

memory for each frequency group; when the frequency group is changed,

the radio operates according to the channels stored in memory for that

group.

Storage in memory of Weather Channels or Channel 70 for DSC is disabled.

When storage of these channels is attempted, the registration is terminated

and an error alert tone sounds.

Storing Channels in Memory

From the Working Channel mode, select the channel to be stored. Press

the FUNC key followed by the 1/MEM key. The MEM indicator appears

when the registration is complete.

Deleting Channels from Memory

From the Working Channel mode, select the channel to be deleted. Press

the FUNC key followed by the 1/MEM key. The MEM indicator disappears

when the channel is deleted.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-14

Operation with a Full Function Handset

4.4.9 Setting the Transmission Power Output

The transmission output can be set at either 1W or 25W. When the power

supply is switched on, the output is 25W. Pressing the FUNC key followed

by the 9/1/25 key alternates the transmission between 25W and 1W.

When 1W is selected, the 1W indicator is displayed on the LCD. When

25W is selected the 1W indicator disappears.

4.4.10 Desensitized Reception (Local Mode)

You can set the RAY215 to reduce the receiving sensitivity in high traffic

areas to decrease unwanted reception. This is also known as local mode.

To select this mode, press the FUNC key followed by the 7/D/L key. While

the desensitize function (local mode) is active, the DESENS indicator

appears in the LCD display. To return to full receiver sensitivity (distant

mode), again press the FUNC 7/D/L key combination.

4.4.11 LCD Backlight Function

LCD backlight brightness can be set at four different levels. Press the

FUNC/DIM key two times to enter Dimmer mode. Each successive click of

the FUNC/DIM key alternates the brightness from Off, to Low, to Medium,

to High, then back to Off. As the backlight setting is changed, the dot

matrix indicator displays the following messages: DIM OFF for the Off

setting, DIM LOW for Low, DIM MID for Medium, and DIM HI for High.

When the ENT or CLR keys are pressed or when no other key operation is

made for 5 seconds, the current state is accepted and stored in memory,

and the backlight setting operation is complete. The next time the power

supply is switched on, the state of the backlight is recalled and is applied

to each handset individually.

When selecting the DIM OFF setting or pressing any key while in DIM

OFF mode, the display is lit at the DIM LOW setting for 5 seconds and

then turned off. This is so you can view the display in low light

conditions.

4.4.12 Intercom Mode

Intercom mode enables conversation between a fist microphone connected

to the port on the front of the base station and a Full Function Handset

connected to the port on the rear of the base station.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-15

Operation with a Full Function Handset

Note: Using the Intercom is a simplex operation. You must press PTT to

talk to the other station and release PTT to listen.

Making a Call from the Full Function Handset

1. Press the FUNC key followed by the 0/IC key to enter Intercom mode.

IC appears on the large display. While calling, CALLING BASE appears

on the dot matrix display.

When the other station answers the call, the message CALLING turns

to CONNECT.

Note: If the other station does not respond within 60 seconds, the unit

exits Intercom mode.

2. Press PTT to speak to the other station and release PTT to listen.

3. To exit Intercom mode, again press FUNC followed by 0/IC.

Making a Call from the Base Station

1. Press and hold the D/L/I.C. key to enter Intercom mode. IC appears on

the large channel display. While calling, REMOTE flashes on the small

channel display.

When the other station answers the call, REMOTE stops flashing and

appears solid.

Note: If the other station does not respond within 60 seconds, the unit

exits Intercom mode.

2. Press PTT to speak to the other station and release PTT to listen.

3. To exit Intercom mode, again press and hold the D/L/I.C. key.

Receiving a Call with the Full Function Handset

1. When an Intercom call is received, the handset speaker and external

handset speaker both emit a calling tone. If the handset is on the

cradle, the calling tone is not emitted from the handset speaker.

IC appears on the large display and CALL FROM BASE flashes on the

dot matrix display.

2. To answer the call, press PTT. The calling tone ceases and the dot

matrix display goes blank.

Note: If not answered within 60 seconds after being called, the call

terminates and the display returns to its previous state.

3. Press PTT to speak to the other station and release PTT to listen.

4. To exit Intercom mode, again press FUNC followed by 0/IC.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-16

Operation with a Full Function Handset

Receiving a Call at the Base Station

1. When an Intercom call is received, the base station speaker emits a

calling tone. IC appears on the large channel display and REMOTE

flashes on the small channel display.

2. To answer the call, press PTT. The calling tone ceases and REMOTE

stops flashing and appears solid.

Note: If not answered within 60 seconds after being called, the call

terminates and the display returns to its previous state.

3. Press PTT to speak to the other station and release PTT to listen.

4. To exit Intercom mode, again press and hold the D/L/I.C. key.

4.4.13 Scan Mode

During Scan mode, the RAY215 searches through the channels, stops

when radio traffic is detected, then resumes scanning after the traffic ceases.

Two scan functions are available:All Channel Scan and Memory Channel

Scan. TheAll Channel Scan function searches all channels (except Weather

Channels or Channel 70) within the same frequency group. The Memory

Channel Scan searches only the channels stored in memory in the same

group.

The scan begins from the channel following the one currently indicated.

The scan is suspended when a carrier is detected. Five seconds after the

carrier ceases, the scan resumes with the next channel. If the carrier is

detected again before 5 seconds elapse, the timer is re-initialized. Press the

2/SCAN key to resume the scan from the next channel. To cancel the scan,

press the CLR key or press FUNC followed by 2/SCAN.

Upon reaching Channel 88, the radio scrolls back to Channel 1 and

continues the scan. If the scan stops on a channel with traffic and you

wish to communicate with the other party, press the PTT key to cancel the

scan and remain on that channel.

Note: Both Scan functions exclude Channel 70, which is used exclusively

for receiving and transmitting Digital Selective Calling (DSC) functions.

Using Memory Scan

This function is available only when at least one channel has been stored

in memory. Press the FUNC key followed by the 2/SCAN key. The messages

MEM and SCAN flash for 3 seconds on the LCD. A scan of only the

channels in memory is initiated when the 3 seconds elapse or when you

press the ENT key before the 3 seconds elapse.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-17

Operation with a Full Function Handset

To cancel the scan, press the CLR key or press FUNC followed by 2/

SCAN.

UsingAll Scan

Press the FUNC key followed by the 2/SCAN key The messages MEM

and SCAN flash for 3 seconds on the LCD. Before the 3 seconds elapse,

press the 2/SCAN key again to begin All Scan. If the 3 seconds elapse

before you press the 2/SCAN key, the radio will enter Memory Scan.

To cancel the scan, press the CLR key or press FUNC followed by 2/

SCAN.

4.4.14 Monitor Mode

Monitor operation can be implemented in one of two modes: Dual-Watch

or Tri-Watch.

Dual-Watch

In Dual-Watch Mode, the RAY215 operates on the Working Channel while

constantly monitoring the Priority Channel. The radio locks onto the Priority

Channel or the Working Channel whenever it becomes active, then returns

to Dual-Watch when there is no activity.

To start Dual-Watch Mode, select the desired Working Channel then press

the MON key. The Working Channel is displayed on the 7-segment display

and the Priority Channel appears on the right side of the dot matrix display.

To end Dual-Watch mode at the current channel, press the MON key or

the CLR key. If Dual-Watch mode is initiated at Channel 70, the operation

is cancelled and an error alert sounds.

Tri-Watch

In Tri-Watch Mode, the RAY215 operates on the Working Channel while

constantly monitoring the Priority Channel then the previously selected

Weather Channel for severe weather alert broadcasts. When a signal is

detected on the Working Channel or Priority Channel, that channel becomes

active. When there is no longer any activity on the Working Channel or

Priority Channel, the RAY215 returns to Tri-Watch.

If a weather alert broadcast is detected, the RAY215 emits an alert tone and

the WX indicator blinks. Tri-Watch mode terminates and the radio switches

to the WX channel to monitor the severe weather broadcast.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-18

Operation with a Full Function Handset

To start Tri-Watch mode, select the Working Channel then press the FUNC

key followed by the MON/TRI key. The Working Channel appears on the

7-segment display, the Priority Channel appears on the right-most portion

of the dot matrix display, and the Weather Channel appears on the left-

most portion of the dot matrix display.

To end Tri-Watch mode at the current channel, press the MON key or the

CLR key. If Tri-Watch mode is initiated at Channel 70, the operation is

cancelled and an error alert tone sounds.

4.4.15 NMEA Operation

The RAY215 can receive valid position and time information, which are

transmitted during a DSC Distress call. This data can be communicated via

NMEA0183 from a GPS, fishfinder, radar, or any device that outputs GPS

sentences. If the radio does not detect the positional data, it provides

different alerts urging you to find and correct the fault or manually input

the data using the radio’s L/L ENT function, as described in section 4.5.3.2.

Current valid positional data, whether from external device or manually

input, can be viewed using the NAVSTAT Operation described in section

4.5.2.

If a GPS device is not connected via NMEA, the radio emits a 5-second-

long staccato alert tone and flashes the NMEA indicator 2 minutes after

power up. This occurs every time the unit is turned on. The alarm is required

by safety regulations and cannot be disabled.

Operation at Power Up

At power up, the radio monitors the NMEA line for 1 minute. If a signal is

detected on NMEA, the radio determines whether the data is valid. If valid,

the data is input, the NMEA indicator is displayed on handsets, and the

radio enters normal operation mode.

If no GPS signal is detected on NMEA after the 1 minute monitoring period,

a 5-second-long staccato alert tone is emitted and the NMEA indicator

flashes.All the position fields are set to 9’s and the time and date fields are

set to 8’s. The message NO GPS appears in the NAVSTAT screen, although

no positional data is displayed.

If at a later time valid data is received on NMEA, the data is input, the

NMEA indicator is displayed solid (no longer flashing), and the radio

enters normal operation mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-19

Operation with a Full Function Handset

Operation When the Signal is Lost or Becomes Invalid

If positional data that was previously detected becomes invalid or is no

longer detected, the radio monitors the NMEA line for 1 minute for it to be

restored.

If a signal is restored on the NMEA line and the radio determines the data

is valid, the data is input, the NMEA indicator remains illuminated, and the

radio re-enters normal operation mode.

However, if no signal is detected, the NMEA indicator flashes and a 5-

second-long staccato alert tone is emitted. The last received positional

data is retained in memory and can be viewed in the NAVSTAT screen. The

message NO GPS appears in NAVSTAT in the position where the type of

device used to be. The NMEA indicator continues to flash until valid

positional data is received. If valid positional data (from the same source)

is later restored, the NMEA indicator is again displayed solid.

Operation When No Signal Detected for 4 Hours

If no valid positional data is received or input manually within 4 hours of

the previous alert, the NMEA indicator continues to flash and the staccato

alert tone is again emitted. This pattern is repeated every 4 hours if no

positional data has been detected. If no manual input was made during the

previous 23.5 hours, all the position fields are set to 9’s and the time and

date fields are set to 8’s.

4.4.16 Digital Selective Calling (DSC)

The Digital Selective Calling (DSC) protocol is a globally applied system

used to send and receive digital Distress calls as well as Individual andAll

Ships calls on channel 70, the dedicated DSC channel for Marine VHF. For

a Distress call transmission, your RAY215 takes the position and time

information from the input NMEA data along with your Maritime Mobile

Station Identifier (MMSI) and converts it into a digital “packet”. When

transmitted, this digital information lets other ships and shore stations

know where you are and that you are in a Distress situation.

Communications in DSC mode include the following:

1. Transmitting/Receiving an Individual Call

2. Transmitting/Receiving a Group Call

3. Transmitting/Receiving anAll Ships Call

4. Transmitting/Receiving a Distress Call

5. Receiving a Distress Relay Call

Download from Www.Somanuals.com. All Manuals Search And Download.

4-20

Operation with a Full Function Handset

DSC transmission and reception occurs on Channel 70. When the DSC

signal is received, the unit quickly switches over to Channel 70 and performs

the corresponding operation. You will not receive a DSC call if the radio is

transmitting or receiving a non-DSC call.

Note: An MMSI number is required to operate the DSC equipment in this

radio. You can program the MMSI number yourself one time only using

the Menu Operation described in 4.5.4.2 MMSI Number Set Up. Otherwise,

your Raymarine dealer can program or change the number for you.

Individual,All Ships and Group DSC calls come in three varieties: ROUTINE

for normal calls, SAFETY for advisory alerts, and URGENCY for assistance

when life is not in immediate danger.

4.4.16.1 Individual Call to Another Ship (Ship-to-Ship)

An Individual Ship's Call is a DSC call made to a specific ship identified by

its MMSI number. The RAY215 can receive all three types of Individual

calls but can only transmit ROUTINE Individual calls. As with any DSC

operation, the call is made on channel 70.

Transmitting an Individual Call

To call another ship, you must select the Working Channel and a specific

MMSI number. The MMSI number is selected either manually or from a

Phonebook list of preprogrammed numbers specified using the MENU

function. To cancel the call, press and hold the CLR key for 3 seconds.

Press the INDV key to initiate the call data setup operation. After setting

the call data, press the PTT key to send the call.

To Make an Individual Call to Ship (ship-to-ship):

1. Press the INDV key. Ind appears on the 7-segment display and the DSC

indicator is displayed. Pressing the SQ UP/DOWN key alternates

between SHIP and SHORE.

INDV

Alternates with each click

of the SQ UP/DOWN key

2. Select SHIP and press the ENT key.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-21

Operation with a Full Function Handset

3. Scroll with the SQ UP/DOWN keys to select the method for inputting

the MMSI number, either from the Phonebook or manually. Press ENT.

ENT

Alternates with each click

of the SQ UP/DOWN key

4. Select the MMSI number.

BYPHONEBOOK:

Scroll with the SQ UP/DOWN keys, select the name associated with

the desired MMSI number, and press the ENT key. If the MMSI number

is not listed in phonebook, the display reverts to manual input.

ENT

Use SQ UP/DOWN key

to scroll through list of

MMSI nos./nicknames

Note: The Full Function Handset provides you with a phonebook that

holds entries for up to 20 Ship stations and 20 Shore stations. These are

separate from the 10 phonebook entries stored in the base station using

the fist microphone (see section 3.3.17.2). These 10 entries cannot be

selected with the Full Function Handset.

BYMANUALINPUT:

Input the 9-digit MMSI number with the numeric keypad, then press

the ENT key.

numeric

keypad

ENT

Flashing

5. Specify the Working Channel with the SQ UP/DOWN keys and press

the ENT key.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-22

Operation with a Full Function Handset

Note: The working channel selected for the Individual Call is inserted

as the working channel as long as it is an inter-ship simplex channel.

If it is not, the radio selects the next higher simplex channel to insert

as the working channel.

SQ UP/

ENT

DOWN

6. Press the ENT key again. A prompt appears on the display instructing

you to press the PTT key.

7. Press PTT to transmit.

ENT

MMSI number or

nickname is displayed

Note: Only simplex channels (those channels that transmit and receive

on the same frequency) can be selected for ship to ship Individual Calls.

Pressing the SQ UP/DOWN will scroll you through the simplex channels

usable for this operation.

Response

If a response is received after pressing the PTT key, a receive-confirmation

message is displayed.After 5 seconds have elapsed, the channel is changed

to a communication channel and the Individual Ships Call is completed.

ACK

5 sec

If no response is received for 3 minutes after pressing the PTT key, a

prompt to press the PTT key appears once more. After 15 seconds elapses

without pressing the PTT key following the prompt, operation returns to

the state before the call.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-23

Operation with a Full Function Handset

3 min

NO ACK

PTT

Scrolls every second

4.4.16.2 Individual Call to Shore Station (Ship-to-Shore)

To call a shore station, you must select the specific MMSI number. The

MMSI number can be entered manually or selected from a Phonebook list

of preprogrammed numbers. Channel 16 is automatically assigned for

communications. To cancel the call, press and hold the CLR key for 3

seconds.

To make an Individual Call to Shore Station (ship-to-shore):

1. Select the Shore Station channel.

2. Press the INDV key. Ind appears on the 7-segment display and the DSC

indicator is displayed. Pressing the SQ UP/DOWN key alternates

between SHIP and SHORE.

INDV

ENT

After pressing ENT, the

indication switches to:

PHNBOOK, MANUAL

Alternates with each

click of SQ UP/DOWN

3. Select SHORE and press the ENT key.

4. Scroll with the SQ UP/DOWN keys to select the method for inputting

the MMSI number, either from the phonebook or manually. Press ENT

to input your selection.

5. Select the name by MMSI number from the phonebook by scrolling

with the SQ UP/DOWN keys, and pressing the ENT key.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-24

Operation with a Full Function Handset

SQ UP/

DOWN

ENT

Use SQ UP/DOWN key to scroll through

list of MMSI nicknames. Press ENT when

desired selection is displayed.

ENT

Note: The Full Function Handset provides you with a phonebook that

holds entries for up to 20 Ship stations and 20 Shore stations. These are

separate from the 10 phonebook entries stored in the base station using

the fist microphone (see section 3.3.17.2). These 10 entries cannot be

selected with the Full Function Handset..

Manually input the MMSI number with the numeric keypad, then press

the ENT key.

numeric

keypad

ENT

Flashing

6. Press ENT again. A prompt appears on the display instructing you to

press the PTT key.

7. Press PTT to transmit.

ENT

With manual input, MMSI

number would be displayed

Download from Www.Somanuals.com. All Manuals Search And Download.

4-25

Operation with a Full Function Handset

Response

If a response is received after pressing the PTT key, a receive-confirmation

message is displayed. After 5 seconds have elapsed, the channel is shifted

to a communication channel and the Individual Call is completed.

ACK

5 sec

If no response is received for 3 minutes after pressing the PTT key, a

prompt to press the PTT key appears once more. If the PTT key is not

pressed within 15 seconds after the prompt appears, operation returns to

the state before the call.

3 min

NO ACK

PTT

Scrolls every second

4.4.16.3 Receiving an Individual Call

When an Individual Call is received, the DSC indicator flashes, Ind appears

on the 7-segment display, and the DSC ReceivedAlert is sounded. On the

dot matrix display appears the message RECEIVED IND CALL along with

the type of call: ROUTINE, SAFETY, or URGENCY. If the MMSI number

exists in the Phonebook list, the associated name is also displayed. If no

match is found, the actual numeric value of the MMSI is displayed. Lastly

appears a prompt to press ENT to accept or CLR to log the call. This

sequence scrolls every second.

Until either the ENT key or the CLR key are pressed, the prompt is flashed

at 1-second intervals and is accompanied by an alarm for up to 3 minutes.

If neither ENT nor CLR are pressed during these 3 minutes, the radio

reverts to the operation mode before receiving the Individual Call. The

DSC indicator continues to be flashed on the LCD display until the contents

of the log files can be confirmed.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-26

Operation with a Full Function Handset

If ENT is pressed, the alarm is turned off, and a new prompt appears on the

display, instructing you to press the PTT key. Press PTT to transmit an

acknowledgment (ACK). If PTT is not pressed within 5 seconds of the

prompt appearing, the transmission is done automatically. Pressing the

PTT key causes the channel to change to the communication channel.

Receiving

ENT

After no operation

for 5 seconds

Scrolls

every

second

MMSI number is displayed

if the nickname is not

registered in the list.

If the CLR key is pressed

If the CLR key is pressed, the alarm is turned off, the displays are cleared,

and the received contents are stored in the Log File. The radio then reverts

to the operation mode before receiving the Individual Call.

4.4.16.4 Transmitting a Group Call

You can send and receive DSC calls from groups of stations that share the

same Group MMSI number.

The RAY215 can only transmit ROUTINE Group calls.As with any DSC

operation, the call is made on channel 70.

To make a Group Call:

1. Set up the Group MMSI number as outlined in section 4.5.3.4.

2. Press the INDV key. Ind appears on the 7-segment display, the DSC

indicator is illuminated, and SHIP appears on the dot matrix display.

3. Press the SQ UP/DOWN key to alternate between SHIP, SHORE, and

GROUP. Stop on GROUP. The GROUP message only appears if you

have set up the Group MMSI number as outlined in section 4.5.3.4.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-27

Operation with a Full Function Handset

4. When GROUP appears, press the ENT key. GrP appears on the 7-

segment display and the registered Group MMSI number appears on

the dot matrix display.

INDV

ENT

Group MMSI number

Only appears if Group

MMSI number is set up

via DSC Operation in

Menu Mode

Note: Since only one group MMSI number can be registered at a time,

only one MMSI number can be displayed when GROUP is selected. To

change the group MMSI number, see section 4.5.3.4.

5. Press ENT to accept the MMSI number.

6. Use the SQ UP/DOWN key to select the Working Channel for

communication.

7. When the desired channel number appears, press ENT. The dot matrix

display scrolls between the Working Channel and the Group MMSI

number.

8. If this information is correct, press ENT to accept. A new message

appears, prompting you to press the PTT key.

9. Press PTT. The radio changes over to the selected Working Channel

without waiting for acknowledgment.

ENT

MMSI number

Scrolls between

Working Chanel and

MMSI number

Select Working Chanel

with SQ UP/DOWN key

ENT

PTT

Download from Www.Somanuals.com. All Manuals Search And Download.

4-28

Operation with a Full Function Handset

4.4.16.5 Receiving a Group Call

When a Group Call is received, the DSC indicator flashes, Grp appears on

the 7-segment display, and the DSC ReceivedAlert is sounded. On the dot

matrix display appears the message RECEIVED GRP CALL, along with the

type of call: ROUTINE, SAFETY, or URGENCY. If the MMSI number exists

in the list, the associated name is displayed. If no match is found, the

actual numeric value of the MMSI is displayed. You are then prompted to

press ENT to accept or CLR to log the call.

Until either the ENT key or the CLR key are pressed, the prompt is flashed

at 1-second intervals and is accompanied by an alarm for up to 3 minutes.

If neither ENT nor CLR are pressed during these 3 minutes, the radio

reverts to the operation mode before receiving the Group Call. The DSC

indicator continues to be flashed on the LCD display until the contents of

the log files can be confirmed.

If ENT is pressed, the alarm is turned off, and a new prompt appears on the

display, instructing you to press the PTT key. Press PTT to transmit. If

PTT is not pressed within 5 seconds of the prompt appearing, the

transmission is done automatically. Pressing the PTT key causes the

channel to change to the communication channel.

If the CLR key is pressed, the alarm is turned off, the displays are cleared,

and the received contents are stored in the Log File. The radio then reverts

to the operation mode before receiving the Group Call.

Receiving

ENT

Scrolls

across

display

MMSI number is displayed

if the nickname is not

registered in the list.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-29

Operation with a Full Function Handset

4.4.16.6 Transmitting an All Ships Call

The All Ships Call is used to send out a message to all ships in range that

you need assistance but the situation is not serious enough for a Distress

Call. This call should only be used if hailing for assistance on channel 9 or

16 fails. The RAY215 can transmit and receive all three types ofAll Ships

Calls: ROUTINE, SAFETY, and URGENCY.As with any DSC operation, the

call is made on channel 70. Then, after theAll Ships Call is sent or received,

the radio automatically selects channel 16.

To send anAll Ships Call

1. Press the ALL SHIP key. The message SAFETY appears on the dot

matrix display and the DSC indicator illuminates.

2. Press the SQ UP/DOWN key. The message URGENCYnow appears on

the dot matrix display.

3. Make your selection between SAFETY or URGENCY and press the

ENT key to submit. The prompt RECONFIRM is displayed.

4. Press the ENT key to confirm. A prompt appears on the display,

instructing you to press the PTT key.

5. Press PTT to transmit.

TheAll Ships Call is made on Channel 70.After theAll Ships Call is sent,

the radio automatically switches to channel 16.

ENT

Alternate by pressing the

SQ UP/DOWN key

Download from Www.Somanuals.com. All Manuals Search And Download.

4-30

Operation with a Full Function Handset

4.4.16.7 Receiving an All Ships Call

When anAll Ships Call is received, an alert is sounded. The LCD displays

the type of All Ships call being received, along with the sender's MMSI

number, and a prompt to press ENT to accept or CLR to log the call. The

alert and the displayed message continue until either ENT or CLR is pressed.

If ENT is pressed, the radio switches to Channel 16 and the contents of the

communication are stored in the log. If CLR is pressed, the radio reverts to

the mode before receiving theAll Ships Call and the contents are stored in

the log.

ENT

CLR

If CLR is pressed, the radio

reverts to the mode before

receiving Urgency Call

4.4.16.8 Transmitting a Distress Call

A Distress Call allows you to send out a digital “packet” of data at high

power that includes your position, time, and MMSI number.All ships and

stations outfitted with the correct type of DSC equipment will be able to

pinpoint your position and either relay the information or respond directly.

Using the Distress key overrides all other functions.

Two types of Distress Calls can be made: one that specifies the type of

distress and one that does not.

Unspecified Distress Call

To make a Distress Call without specifying type of distress:

1. Open the door labeled DISTRESS on the back of the handset and press

and hold the DISTRESS key. After one second, dSr flashes on the 7-

segment display and the DSC indicator appears. On the dot matrix

display, countdown message appears prompting you to hold the

DISTRESS key for 4 more seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-31

Operation with a Full Function Handset

2. Continue to hold the DISTRESS key for the duration of the countdown.

An alert tone is sounded at one-second intervals.

press

DISTRESS

Countdown starts 1 second after pressing

DISTRESS key. The types of DISTRESS

can be selected by releasing the key

before the Countdown is completed.

Note: If you fail to hold the key for the full 5 seconds, the DISTRESS

call is cancelled.

3. After the countdown has completed, the message RELEASE appears

on the dot matrix display. Release the DISTRESS key.

The unit switches to channel 16, displays the message AWAIT ACK,

and monitors channel 70 for an acknowledgment.

release

DISTRESS

The unit retransmits the DISTRESS call at random intervals of 3.5 to 4.5

minutes, until a response is received or the call is manually cancelled.

To exit the Distress mode, press the CLR key and hold for 3 seconds. The

unit reverts to the state it was in before the call was initiated.

press and hold

CLR for 3 secs

When a response is received, the DSC indicator flashes and the DSC

Distress alert is sounded. The LCD scrolls a message that the DISTRESS

has been acknowledged, along with the sending station's MMSI number

or nickname. The message and alert are repeated until the CLR key is

pressed.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-32

Operation with a Full Function Handset

CLR

Flashing

When the CLR key is pressed, the unit exits the DSC mode continues

monitoring Channel 16 on high power.

Regardless of the handset state, the DSC Distress alert is sounded at

maximum volume on the external speaker, even if the volume knob has

been rotated all the way OFF.

You can mute the alert tone by pressing the CLR key for one second.

Pressing CLR only turns off the alert sound; it does not interrupt the

Distress call.

Specified Distress Call

You can assign one of eleven distress types to the call to provide the

potential rescuing station additional information if time and circumstances

permit. The Nature of the distress call can be selected using the DISTRESS

key as outlined below or in the system MENU as outlined in section 4.5.3.1.

Below are the messages and their meanings:

Message

FIRE

Meaning

fire

Message

ADRIFT

Meaning

drifting

FLOODNG

COLLISN

AGROUND

LISTING

SINKING

flooding

collision

run aground

listing

UNDESIG

ABNDSHP

PIRACY

undesignated

abandoning ship

piracy

MANONBD man overboard

sinking

Download from Www.Somanuals.com. All Manuals Search And Download.

4-33

Operation with a Full Function Handset

To make a Distress Call specifying the type of distress:

1. Open the door labeled DISTRESS on the back of the handset and press

and release the DISTRESS key on the back of the handset. dSr appears

on the 7-segment display and the DSC indicator illuminates. On the dot

matrix display, the message FIRE appears.

press and

release

DISTRESS

SQ UP/

DOWN

2. If FIRE is the message you wish to attach, press the ENT key.

If FIRE is not the message you wish to attach, scroll through the list

with the SQ UP/DOWN keys. When the appropriate message is

displayed, press the ENT key.

On the dot matrix display, appears the distress type plus a message

prompting you to press and hold the DISTRESS key.

3. To send the distress signal, press and hold the DISTRESS key. After

one second, dSr flashes and a countdown message appears on the dot

matrix display, prompting you to hold the DISTRESS key for 4 more

seconds.

hold

DISTRESS

4. Continue to hold the DISTRESS key for the duration of the countdown.

A tone sounds every second.

Note: If you fail to hold the key for the full 5 seconds, the DISTRESS

call is cancelled.

After the 5 seconds have elapsed, the message RELEASE appears,

prompting you to release the key.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-34

Operation with a Full Function Handset

5. When this prompt appears, release the DISTRESS key. The unit is

switched to Channel 16, displays the message AWAIT ACK, and

monitors channel 70 for an acknowledgment.

release

DISTRESS

dSr stops flashing and the distress alarm sounds continuously. The

unit retransmits the DISTRESS call at random intervals of 3.5 to 4.5

minutes, until a response is received or the call is manually cancelled.

Note: When a Distress Call is sent, the unit emits a VERY LOUD distress

alarm tone. To mute the alarm without interrupting the Distress Call,

press and release CLR. The radio will remain in DSC mode.

To exit the Distress mode, press the CLR key and hold for 3 seconds. The

unit reverts to the state it was in before the call was initiated.

press and hold

CLR for 3 secs

When a response is received, the DSC indicator flashes and the DSC

Distress alert is sounded. The LCD scrolls a message that the DISTRESS

has been acknowledged, along with the sending station's MMSI number.

The message and alert are repeated until the CLR key is pressed.

When the CLR key is pressed, the unit exits the DSC mode continues

monitoring Channel 16 on high power. Regardless of the handset state, the

DSC Distress alert is sounded at maximum volume on the external speaker.

Note: If a Distress Call is transmitted in error, you should notify other

vessels that no real emergency exists. On Channel 16, announce your

name, the vessel's name, and your MMSI number then state that the

Distress call was sent by accident and should be disregarded.

4.4.16.9 Receiving a Distress Call

When a Distress call is received, the DSC indicator flashes, dSr appears

on the 7-segment display, and the DSC Distress alert is sounded. On the

dot matrix display are scrolled RECEIVED, DISTRESS, the type of distress,

the MMSI number, the transmitting time, the latitude, and longitude of the

transmitting station.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-35

Operation with a Full Function Handset

The DSC DistressAlarm and displayed message continue until either ENT

or CLR are pressed. Pressing ENT stores the contents of the call in the log

and switches the radio to Channel 16. Pressing CLR also logs the call but

then reverts the radio to the mode before receiving the Distress call.

ENT

CLR

If CLR is pressed, the radio

reverts to the mode before

receiving Distress Call

4.4.16.10 Receiving a Distress Relay Call

Sometimes a ship’s distress call can be relayed from another ship or a

shore station. The RAY215 can only receive a Relayed Distress call that

has been addressed to All Ships.

When a Relayed Distress call is received, the DSC indicator flashes, dSr

appears on the 7-segment display, and the DSC Distress alert is sounded.

On the dot matrix display are scrolled RECEIVED, RELAY, the MMSI number

of the station making the call, DISTRESS, the type of distress, the MMSI

number of the ship in distress, the latitude and longitude of that ship, and

the time of transmission.

ENT or CLR

MMSI number of transmitting station. If registered

in the list, the nickname appears instead.

MMSI number of ship in distress. If not

known, UNKNOWN appears here instead.

The displayed message continues until either ENT or CLR is pressed. At

that time, the radio switches to Channel 16 in high power and the contents

of the communication are stored in the Log File.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-36

Operation with a Full Function Handset

4.4.16.11

Using the DSC Log

The RAY215 maintains 3 separate logs for storing information about sent

and received DSC calls. The logs are divided by type:

• Individual,All Ships, and Group Calls

• Distress Calls

• Relay Distress Calls

Each log can store up to 10 calls. If more than ten DSC calls of a particular

type are logged, the oldest one is deleted as the new one comes in.

To view a log:

1. Press FUNC followed by LOG/CLR to enter DSC Log mode. LoGappears

on the seven segment display and the log type appears on the dot

matrix display.

2. Press the SQ UP/DOWN keys to scroll through the available logs:

DISTR for Distress calls

I/A/G for Individual/All Ships/and Group Calls

RELAYfor Relay Distress Calls

3. When the desired log appears, press ENT to accept. The log number

appears next to the log type, beginning with 0, the latest entry.

4. Press the SQ UP/DOWN keys to scroll through the entry numbers 0-9

for the particular log. After one second of displaying the log entry

number, the log data for that entry begins scrolling across the dot

matrix display, containing the following information:

•

Type of call

MMSI number

Nature of the call (Routine, Safety, or Urgency), if applicable

CLR-EXIT

ENT-DELETE

If no call exists for a particular log entry number, the data appears as all

dashes (-).

5. Press the CLR key to delete the log entry from memory or press CLR to

exit DSC Log mode without making changes. If an entry is deleted, the

next older entry assumes the deleted entry’s number. For example, if

log 1 is deleted, log 2 becomes log 1, log 3 becomes log 2, and so on.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-37

Operation with a Full Function Handset

4.5

Menu Operation

The menu operation is used for making various settings and confirming

the current state. The operation is roughly divided in three functions as

follows:

Function Purpose

1.NAVSTA Indicates the information input from NMEA.

2. DSC

To register/modify various settings related to DSC.

3. SETTING To program the MMSI number.

4.5.1 Selecting the Menu Operation

To initiate the Menu function:

1. Press the FUNC key followed by the MENU key. Mn appears on the 7-

segment display and NAVSTAT is shown on the dot matrix display.

2. To scroll through these first level menu items, press the SQ UP/DOWN

key. The indicators alternate between NAVSTAT, DSC, and SETTING.

3. Select the desired operation and press the ENT key to enter that

particular menu item.

To exit the Menu operation, press and hold the CLR key for 3 seconds.

FUNC MENU

Download from Www.Somanuals.com. All Manuals Search And Download.

4-38

Operation with a Full Function Handset

4.5.2 NAVSTAT Operation

This operation indicates on the LCD display the position information that

has been input via NMEA or has been manually input using the LL/ENT

function as outlined in section 4.5.3.2.

To view current position information:

1. Press the FUNC key followed by the MENU key to initiate the Menu

operation.

2. Select NAVSTAT and press the ENT key. The following five items are

automatically displayed at 3-second intervals in the following order:

1. Latitude

4. UTC Date (Y/M/D)

2. Longitude

3. UTC Time

5. Position source (GPS, DIFF GPS, NO GPS)

This data is for viewing only and can not be altered.

after 3 seconds elapse

3 secs

To return to the main menu screen, again press FUNC followed by MENU.

To exit the Menu operation, press and hold the CLR key for 3 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-39

Operation with a Full Function Handset

4.5.3 DSC Operation

DSC operation includes the manual entry of latitude/longitude, listing of

other ship’s MMSI numbers for ship-to-ship and ship-to-shore

communications, and listing of Group MMSI number.

To initiate the DSC operation:

1. Press the FUNC key followed by the MENU key to initiate the Menu

operation.

2. Select DSC and press the ENT key. The 7-segment display shows dSC

and the dot matrix display shows L/L ENT.

The DSC Main Menu is made up of NATURE, L/LENT, PHNBOOK, and

GROUP submenus.

SQ UP/DOWN

3. Press the SQ UP/DOWN key until the desired operation is

displayed:

NATURE

L/LENT

PHNBOOK

GROUP

Select type of Distress Call

Manual entry of latitude/longitude

Listing of MMSI number

Listing of Group MMSI number

4. Press the ENT key to submit.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-40

Operation with a Full Function Handset

4.5.3.1 Selecting Distress Call Type (NATURE)

This menu item is used to select the nature of a distress call before the call

is sent. The selected information will be sent along with the distress call.

To select the nature of the distress that will be included with the call:

1. As described in section 4.5.3 DSC Operation above, select the DSC

operation NATURE.

2. Press the ENT key to initiate the process. The 7-segment display shows

nAt and the dot matrix display shows FIRE.

3. Use the SQ UP/DOWN key to select the type of distress.

ENT

Select

with

SQ UP/

DOWN

4. After selecting the desired distress type, press ENT. You are prompted

to press the DISTRESS key.

5. To send the distress call at this time, press and hold the DISTRESS key.

Follow the instructions on the display or the steps described in section

4.4.16.8.

6. To cancel the distress call, press and hold CLR for 3 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-41

Operation with a Full Function Handset

4.5.3.2 Manual Entry of Latitude/Longitude (L/L ENT)

This operation is used to manually enter the latitude/longitude and UTC

time when normal NMEA input of the position information is not available.

The radio will sound a 5-second-long alert tone every four hours to remind

you to update your position.

1. As described in section 4.5.3 DSC Operation above, select the DSC

operation L/L ENT. The 7-segment display shows L L, while the dot

matrix display shows the latest latitude data.

2. Press one of the following keys to initiate the corresponding

operation:

Keys

Action

0 - 9 keys

Changes the flashing numeric value (see step 3), then

advances to the next digit's place.

Advances from Latitude, to Longitude, to UTC.

ENT key

CLR key

SQ UP/

Returns to the previous subject item.

For Latitude, alternates between N and S.

DOWN key For Longitude, alternates between E andW.

For UTC, no effect.

3. The subject items can be changed in the following order. Numeric values

that can be changed are flashing:

1. Degrees of lat at ten’s place

2. Degrees of lat at unit's place

3. Minutes of lat at ten’s place

4. Minutes of lat at unit's place

8. Minutes of lon at ten’s place

9. Minutes of lon at unit's place

10. Hours of UTC at ten’s place

11. Hours of UTC at unit's place

5. Degrees of lon at hundred’s place 12. Minutes of UTC at ten’s place

6. Degrees of lon at ten’s place

13. Minutes of UTC at unit’s place

7. Degrees of lon at unit's place

4. After changing the subject item, the display scrolls from latitude to

longitude to UTC. To submit the change of the position data as shown

in the display, press the ENT key. The unit exits Menu mode and returns

to normal operation.

To exit the Menu operation, press and hold the CLR key for 3 seconds.

The following illustration shows an example of the operation:

Download from Www.Somanuals.com. All Manuals Search And Download.

4-42

Operation with a Full Function Handset

press 1

press ENT

press 5

Flashing

press ENT

press 7

Flashing

press ENT

press 0

press ENT

Flashing

press ENT

press 7

press ENT

Flashing

press 2

press 0

press ENT

Flashing

press ENT

Flashing

press ENT

Download from Www.Somanuals.com. All Manuals Search And Download.

4-43

Operation with a Full Function Handset

4.5.3.3 Modifying the MMSI Number List (PHNBOOK)

This operation is used to modify the “phonebook” lists of MMSI numbers

used for DSC Individual Calls. Two lists are available: one for Ship stations

and one for Shore stations. Each list allows you to register the MMSI

number and nickname for up to 20 Ship and 20 Shore stations.

Note: The 20 Ship stations and 20 Shore stations in this phonebook are

separate from the 10 phonebook entries stored in the base station using

the fist microphone (see section 3.3.17.2). All 50 entries are available for

you to use.

1. As described in section 4.5.3 DSC Operation above, select the DSC

operation PHNBOOK.

2. Press the ENT key to initiate the process. The 7-segment display shows

Phb and the dot matrix display shows SHIP.

ENT

3. Use the SQ UP/DOWN key to select between SHIP or SHORE.

4. Press the ENT key to turn to submit your selection.

Modifying the List of Ship Stations

In this operation, a ship is registered (added) to or deleted from the

phonebook list for ship stations.

1. When SHIP is displayed, press the ENT key. The 7-segment display

shows SHP, while on the dot matrix display shows ENTRY.

2. The list can hold a maximum of 20 entries. If a list is already full or if the

list becomes full during this process, the indicator PHNBOOK IS FULL

is displayed.

3. To delete an item from the list, use the SQ UP/DOWN key to select

DELETE and press the ENT key. If no station has yet been registered,

the message PHNBOOK IS EMPTY is displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-44

Operation with a Full Function Handset

ENT

Note: Pressing and holding the CLR key for 3 seconds during either

ENTRY or DELETE returns operation to the mode before the Menu

operation began.

Adding Ship Stations to the List

To add to the phonebook list for ship stations, input the MMSI number

and nickname of the station.

1. To enter the MMSI number, press the corresponding numeric keys (0

through 9). The currently selected location is indicated by a flashing

“–” character. Pressing a numeric key enters that value then advances

to the next digit's place. To go back by 1 digit, press the CLR key.

2. To enter the nickname, use the numeric keys (0 through 9) to input the

associated alpha or numeric value (refer to section 4.2 Controls and

LCD Display). The currently selected location is indicated by the

flashing “–” character. After inputting the desired letter or numeral,

press the ENT key to submit the entry and proceed to the next place.

To go back by 1 digit, press the CLR key.

If no nickname is to be registered, press the ENT key for all characters

so that they all display a “–”.

3. When the message CONT? Y appears, press the ENT key to submit.

Note: The 0 key will enter only the numeral “0”, while the 1 key will

alternately enter “1” and “space”. The 0 and 1 keys do not have associated

alpha characters.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-45

Operation with a Full Function Handset

ENT

Input remainder

of MMSI number

Flashing

This display is shown only if the list already

has the maximum 20 stations registered

7/PQRS

(twice)

ENT

Flashing

2/ABC

ENT

Input remainder

of MMSI name

Flashing

ENT

Pressing ENT while "Y" is displayed

registers the station and exits Menu

mode.

Pressing ENT while "N" is displayed

exits Menu mode without registering

the station.

Deleting Ship Stations from the List

When the ship station phonebook is selected, the oldest MMSI number or

nickname flashes on the dot matrix display.

1. Press the SQ UP/DOWN key to scroll through the registered stations

until the station to be deleted is displayed.

2. Press the ENT key; the message DEL? Y is displayed.

3. Press the ENT key to process the deletion and exit the Menu operation.

To exit without deleting, press the SQ UP/DOWN key until DEL? N is

displayed. If the list has no stations entered, the message PHNBOOK

IS EMPTY HOLD DOWN CLR KEY is displayed. Press and hold the

CLR key for 3 seconds to exit Menu mode.

ENT

Download from Www.Somanuals.com. All Manuals Search And Download.

4-46

Operation with a Full Function Handset

Modifying the List of Shore Stations

In this operation, a shore (coast) station is registered (added) to or deleted

from the phonebook list.

1. When SHORE is displayed, press the ENT key. SHO appears on the 7-

segment display, while on the dot matrix display shows ENTRY.

2. The ENTRY selection is used to register (add) an item to the list. Press

the ENT key to accept.

The list can hold a maximum of 20 entries. If a list is already full or if the

list becomes full during this process, the indicator PHNBOOK IS FULL

is displayed.

3. To delete an item from the list, use the SQ UP/DOWN key to select

DELETE and press the ENT key. If no station has yet been registered,

the message PHNBOOK IS EMPTY is displayed.

ENT

Note: Pressing and holding the CLR key for 3 seconds during either

ENTRY or DELETE returns operation to the mode before the Menu

operation began.

Adding Shore Stations to the List

To add to the phonebook list for shore stations, input the MMSI number

and nickname of the station.

1. To enter the MMSI number, press the corresponding numeric keys

(0 through 9). The currently selected location is indicated by a flashing

“–” character. Pressing a numeric key enters that value then advances

to the next digit's place. To go back by 1 digit, press the CLR key.

2. To enter the nickname, use the numeric keys (0 through 9) to input their

associated alpha or numeric value (refer to section 4.2 Controls and

LCD Display). The currently selected location is indicated by a flashing

“–” character. After inputting the desired letter or numeral, press the

ENT key to submit the entry and proceed to the next place. To go back

by 1 digit, press the CLR key.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-47

Operation with a Full Function Handset

3. When the message CONT? Y appears, press the ENT key to submit the

registration.

If no nickname is to be registered, press the ENT key for all characters

so that they all display a “–”.

1-8

ENT

Flashing

If the maximum 20 stations are already

registered, this display is shown and the

radio shifts to Delete mode

Input remainder

of MMSI number

To DELETE mode

7/PQRS

(twice)

ENT

Flashing

2/ABC

ENT

Input remainder

of MMSI name

Flashing

ENT

Pressing ENT while "Y" is displayed

registers the station and exits Menu

mode.

Pressing ENT while "N" is displayed

exits Menu mode without registering

the station.

Note: The 0 key will enter only the numeral “0”, while the 1 key will

alternately enter “1” and “space”. The 0 and 1 keys do not have associated

alpha characters.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-48

Operation with a Full Function Handset

Deleting Shore Stations from the List

When the shore station phonebook is selected, the oldest MMSI number

or nickname flashes on the dot matrix display.

1. Press the SQ UP/DOWN key to scroll through the registered stations

until the station to be deleted is displayed.

2. Press the ENT key; the message DEL? Y is displayed.

3. Press the ENT key to process the deletion and exit the Menu operation.

To exit without deleting, press the SQ UP/DOWN key until DEL? N is

displayed. If the list has no stations entered, the message PHNBOOK

IS EMPTY HOLD DOWN CLR KEY is displayed. Press and hold the

CLR key for 3 seconds to exit Menu mode.

SQ UP

/DOWN

ENT

4.5.3.4 Modifying the MMSI Group Number (GROUP)

This operation modifies the MMSI number to be used in receiving a Group

Digital Selective Call.

1. As described in section 4.5.3 DSC Operation above, select the DSC

operation GROUP.

2. Press the ENT key to initiate the process. The 7-segment display shows

GrP and the dot matrix display shows ENTRY.

3. Use the SQ UP/DOWN key to alternate between ENTRYor DELETE.

4. Press the ENT key to turn to submit the desired selection.

ENT

Download from Www.Somanuals.com. All Manuals Search And Download.

3-49

Operation with a Full Function Handset

Entering a Group MMSI Number

To enter a Group MMSI number, select ENTRY then press the ENT key.

Use the numeric keys (0 through 9) to input desired group number. The

currently selected location is indicated by a flashing “–” character. Pressing

a numeric key enters that value then advances to the next place. To go

back by 1 digit, press the CLR key.

After the last position has been filled, the message CONT? Y appears.

Press ENT to register the group and exit the Menu operation. To exit

without registering, press SQ UP/DOWN until DEL? N is displayed. Press

the ENT key and operation returns to mode before the Menu operation

began.

Note: By default, the first digit of the Group MMSI is always “0”.

numeric

ENT

keypad

ENT

Deleting a Group MMSI Number

Use the SQ UP/DOWN key to select DELETE. To delete the contents

indicated, press the ENT key and the message DEL? Y is displayed. Press

the ENT key to process the deletion and exit the Menu operation. To exit

without deleting, press the SQ UP/DOWN key until DEL? N is displayed.

Press the ENT key and operation returns to the mode before the Menu

operation began.

ENT

Download from Www.Somanuals.com. All Manuals Search And Download.

4-50

Operation with a Full Function Handset

4.5.4 Setting the MMSI Number

This operation stores the MMSI number required for DSC communications,

including distress calls. You can request an MMSI number when you

apply for a radio license. If your vessel does not require a license, you may

obtain an MMSI by contacting either BoatUS (www.boatus.com) or

MariTEL(www.maritelusa.com).

Notes:

• This is a one time operation. Once the MMSI number has been

programmed, you will not be able to change it.

• Until the MMSI number is programmed, all DSC functionality is disabled.

Pressing the INDV, ALL SHIP, and DISTRESS buttons will only sound

an error alert.

1. Press the FUNC key followed by the MENU key to initiate the Menu

mode. Mn appears on the 7-segment display and NAVSTAT appears

on the dot matrix display.

2. Press the SQ UP/DOWN key to select SETTING.

3. Press the ENT key. The message SET appears on the 7-segment display

and MY MMSI appears on the dot matrix display.

ENT

4. Press the ENT key to submit. MS appears on the 7-segment display.

If the MMSI number has already been saved to the unit, the dot matrix

display scrolls the programmed MMSI number.

If the MMSI number has not yet been saved to the unit, the dot matrix

display scrolls PLEASE PROGRAM MMSI NO.

5. Press ENT. Nine underscore characters appear, which are placeholders

for the 9 digits of the MMSI number. The first character place to be

input is flashing.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-51

Operation with a Full Function Handset

Pressing the following keys initiate the corresponding operation:

Keys

0 - 9 keys

Action

Changes the flashing numeric value, then advances to the

next digit's place.

ENT key

CLR key

Advances the (flashing) subject item to the next one without

changing the numeric value. Advances to the next screen

after entering the last (ninth) digit.

Returns to the previous subject item. Pressing and holding

for 3 seconds exits the operation and returns to the mode

before the operation began.

6. Input your MMSI number using the numeric keypad.

7. Press the ENT key. The message ENT -ACCEPT, CLR - EXIT scrolls

across the display.

8. Press the ENT key to submit the number. The message ENTER MMSI

NO.AGAIN is displayed.

9. Press ENT. The nine underscore placeholders appear once more.

10. Again input the MMSI number with the numeric keypad.

11. Press ENT to submit. If the second MMSI number you input matches

the first, the message ENT -ACCEPT, CLR - EXIT is again displayed.

Note: If the two MMSI numbers don’t match, the message MMSI NO. NOT

MATCH PRESS ENT scrolls across the display. Press ENT to exit the

Menu mode and try again from step 1.

12. Press ENT to verify. The message ENT - STORE, CLR - EXIT is

displayed.

13. Press ENT one last time to register the MMSI number in memory.

Operation returns to the mode before the Menu mode began.

Download from Www.Somanuals.com. All Manuals Search And Download.

4-52

Operation with a Full Function Handset

To exit without making changes at any time, press and hold CLR for 3

seconds.

ENT

Flashing

Input MMSI

number using

numeric keypad

ENT

Flashing

re-enter

MMSI No.

ENT

Flashing

ENT

Download from Www.Somanuals.com. All Manuals Search And Download.

5-1

Maintenance

Section 5

Maintenance

5.1 How to Contact Raymarine

The RAY215 is designed to provide long periods of trouble-free operation.

It is recognized, however, that environmental and other factors may result

in a need for occasional service.

In the US

Technical Support

1-800-539-5539 ext. 2444, or

1-603-881-5200 ext. 2444

You can reach our Technical Support Department Monday to Friday 4:00

AM to 6:00 PM Eastern Standard Time. Our Technical Support Specialists

are available to answer installation, operation, and troubleshooting

questions about your Raymarine unit.

Accessories and Parts 1-800-539-5539 ext. 2333, or

1-603-881-5200 ext. 2333

Many Raymarine accessory items and parts are available through your

authorized Raymarine dealer. However if you are in need of an item not

available through your retailer feel free to contact our Customer Service

department Monday to Friday 8:15AM to 5:00 PM Eastern Standard Time.

If you are uncertain about what item to choose for your Raymarine unit

please contact our Technical Support Department Prior to placing your

order at 1-800-539-5539 ext. 2065.

In the unlikely event your Raymarine unit should develop a problem please

contact the Raymarine dealer from where the unit was purchased. Your

Raymarine dealer is best equipped to handle your service needs.

Service may also obtained by returning your unit to Raymarine's Product

Repair Center at the address below.

Raymarine, Inc.

Product Repair Center

22 Cotton Road, Unit D

Nashua, NH 03063-4219

In Europe

In Europe, Raymarine support, service and accessories may be obtained

from your authorized dealer, or contact:

Download from Www.Somanuals.com. All Manuals Search And Download.

5-2

Maintenance

Raymarine Limited

Anchorage Park

Portsmouth, Hampshire

England PO3 5TD

Tel +44 (0) 23 9269 3611

Fax +44 (0) 23 9269 4642

Technical Support Tel +44 (0) 23 9269 3611

Fax +44 (0) 23 9269 4642

The Technical Services Department handles inquiries concerning

installation, operation, fault diagnosis and repair.

Accessories and Parts

Raymarine accessory items and parts are available through your authorized

Raymarine dealer. Please refer to the lists of component part numbers and

optional accessories in Section 2.2.1 of this handbook and have the

Raymarine part number ready when speaking with your dealer. If you are

uncertain about what item to choose for your Raymarine unit, please contact

our Customer Services Department prior to placing your order.

Worldwide Support

Please contact the authorized distributor in your country.Alist of worldwide

distributors is supplied with your unit and on the Raymarine website.

On the Internet

You can also reach us on the Raymarine World Wide Web site:

www.raymarine.com

Navigate to the Customer Support page, which provides links for:

•

Finding Factory Service locations and Authorized Dealers near you

Accessing handbooks in Adobe Acrobat format

Searching questions and answers in our solution database by product,

category, keywords, or phrases

•

Submitting a question to our technical support staff, who reply to you

by e-mail

Logging in to check the status of your questions, modify your answer

update notifications, or update your personal profile

Questions can be sent directly to our Technical Support Department on

the Customer Support page by clicking Ask Raymarine.

Download from Www.Somanuals.com. All Manuals Search And Download.

5-3

Maintenance

5.2 Prevent at ive Maint enance

The RAY215 has been constructed to be virtually maintenance free. Your

attention to a few basic points should assure many years of service.

1.Although the unit is waterproof, always keep the unit as dry as possible.

2. Clean the exterior of the unit with a tissue or soft non-abrasive cloth.

CAUTION

Do not use solvents or other chemicals for cleaning this equipment.

3. Inspect the radio case and antenna for any physical damage.

5.3 Specifications

5.3.1 Transmitter

Channels

All available US, International and Canada VHF

Marine band

Frequency Stability

+/- 10PPM (+/- 0.001%)

(-20 °C to +50 °C)

Frequency Range

Channel Spacing

Power Output

156.025 to 157.425MHz

25 kHz Increments

25 Watts switchable to 1 Watt into 50 Ohms at

13.6VDC

Modulation

Frequency modulated 16F3

ModulationAudio Response Shall not vary +1/-3 dB from true 6 dB pre-

emphasis from 300 to 2500Hz, reference 1000Hz.

Audio frequencies 3-20 kHz shall be attenuated

(at 1 kHz by 60 log f/3 dB.Above 20kHz by 50dB)

FMHum&Noiselevel

Audio Distortion

Less than -40dB below audio

Less than 10% at 1kHz for 3kHz deviation

Spurious & Harmonic Attenuated at least 43+10log Po (below rated

radiated carrier Emissions power) per FCC Rules

Part 2 & 80

Antenna Impedance

50Ohm

Transmitter Protection Open and short antenna protection circuit for 10

minute transmission

Download from Www.Somanuals.com. All Manuals Search And Download.

5-4

Maintenance

5.3.2 Receiver

Channels

All available US, International, Canadian VHF

Marine Band

Frequency Range

Frequency Stability

Usable Sensitivity

Threshold

Adjacent Channel Rejection

Spurious Image Rejection

IntermodulationRejection

Audio Output

156.025 to 163.275 MHz in 25 kHz increments

+/- 10 PPM (+/- 0.001%) from -20 °C to +50 °C

0.23µV @ 12dB SINAD

1.0µ full squelch

70dB

2 Watts or more at 10% or less distortion into 4

Ohm load (internal)

Hum&NoiseinAudio

Less than -40dB

5.3.3 Operating Requirement

Input Voltage

Current Required

Transmit

13.6 VDC +/- 15% (11.6 to 15.6 VDC)

Typical 6 amp at 25 Watts

Typical 2 amp at 1 Watt

Operating Temperature -20 °C to +50 °C

Duty Cycle

Continuous, 80% receive, 20% transmit

(max 10 min, @25 °C)

Humidity

100% at 50 °C for 8 hours

5.3.4 Radio Dimensions

Base Station Transceiver

Height

Width

Depth

Weight

3.15 inches (80 mm)

7.68 inches (195 mm)

6.70 inches (170 mm)

Approx. 2.2 lbs (1.0 kg)

Fist Microphone

Height

Width

Depth

Weight

3.54 inches (90 mm)

2.28 inches (53 mm)

1.65 inches (42 mm)

Approx. 0.30 lbs (138 g)

Download from Www.Somanuals.com. All Manuals Search And Download.

5-5

Maintenance

Optional Full Function Handset (FFHS)

Height

6.81 inches (173 mm)

2.25 inches (57 mm)

1.1 inches (28 mm)

Width

Depth

Weight

Approx. 0.30 lbs (138 g)

Optional FFHS Cradle

Height

1.97 inches (50 mm)

Width

2.52 inches (64 mm)

Length

4.02 inches (102.1 mm)

Weight

Approx. 0.15 lbs (70 g) (without cables)

Optional FFHS External Speaker

Height

Width

Depth

Weight

4.48 inches (114 mm)

4.33 inches (110 mm)

1.57 inches (40 mm)

Approx. 0.75 lbs (340 g)

Download from Www.Somanuals.com. All Manuals Search And Download.

5-6

Maintenance

This page intentionally left blank

Download from Www.Somanuals.com. All Manuals Search And Download.

5-7

Maintenance

5.4 Drawings

Assembly Drawing

Download from Www.Somanuals.com. All Manuals Search And Download.

5-8

Maintenance

Block Diagram

RF PCB

Download from Www.Somanuals.com. All Manuals Search And Download.

5-9

Maintenance

Control PCB

Download from Www.Somanuals.com. All Manuals Search And Download.

5-10

Maintenance

Front PCB

Microphone PCB

Download from Www.Somanuals.com. All Manuals Search And Download.

6-1

Appendix

Section 6

Appendix

6.1 FCC Licensing Requirements

Raymarine radios comply with the Federal Communications Commission

(FCC) requirements that regulate marine VHF radio usage for the US.

Marine VHF radio users in the US must comply with all applicable FCC

rules and regulations, some of which are described here. This information

was current at the time this handbook was printed. Up-to-date information,

including licensing requirements, can be obtained on the FCC website at:

www.fcc.gov/wtb/marine

Official FCC forms can be obtained on the FCC website at:

www.fcc.gov/formpage.html

Station License

An FCC Ship Radio Station License and Call Sign are not required for most

recreational vessels travelling in US waters. Examples of radio equipment

that do not require a license include: marine VHF radios, any type of

Emergency Position Indicating Radio Beacon (EPIRB), any type of radar,

GPS or LORAN receivers, depth finders, CB radio, or amateur radio (an

amateur license is required). However, you must obtain a license if: (1) you

are required by law or treaty to carry a radio on your vessel; (2) your vessel

travels to foreign ports; (3) you use marine radio equipment on board your

vessel other than the devices listed above. Ships that use MF/HF single

side-band radio, satellite communications, or telegraphy must be licensed

by the FCC.

If required, you can obtain a Station License by completing FCC Form 605

(available from the FCC website). If no fees are required, mail the completed

form to:

Federal Communications Commission

1270 Fairfield Road

Gettysburg, PA17325-7245

If fees are required, send Form 605 and the required fees to:

Federal Communications Commission

Wireless Bureau Applications

P. O. Box 358130

Pittsburgh, PA15251-5130

Download from Www.Somanuals.com. All Manuals Search And Download.

6-2

Appendix

Operator License

An Operator License is not required to operate a VHF Marine Radio within

US territorial waters. However, a license is required to operate the radio if

you dock in a foreign port (including Canada and Mexico) or leave a foreign

port to dock in a U.S. port. You can request a Restricted Radiotelephone

Operator Permit from the FCC by filing Form 753.

Remember:

• Maintain a radio watch on Channel 16. Channel 16 is used for distress

and safety purposes only.

• VHF Channel 70 is used only for Digital Selective Calling (DSC). It can

not be used for general-purpose calling.

• Your VHF transceiver has a high low power switch. Use low power

whenever feasible. Unnecessary high-power operations can interfere with

other important communications.

• Always use your radio call sign at the beginning and end of each

transmission.

• Be sure only qualified persons operate your radio. You are responsible

for control of your radio. Know the rules.

• Limit calls to other vessels to 30 seconds. If you receive no reply, wait 2

minutes; then try again. Keep communications brief and avoid chit-chat.

• Never transmit false distress messages, and never use profanity on the

air.

Other Reminders:

• You can obtain a station license and call sign by completing FCC Form

605 and mailing it with the required fee (if required) to the FCC.

• You need a radio operator license to operate a VHF Marine Radio only if

you plan to dock in a foreign port or leave a foreign port to dock in a U.S.

port.

• Your radio license is not transferable. If you sell your boat, request the

FCC to cancel your station license.

• If you replace your radio, you do not need to change your license unless

the new radio operates on another frequency band. If you install

equipment to operate on another frequency band, apply for modification

of your license.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-3

Appendix

6.2 Marine VHF Channel Usage Guide

Emergency

Calling

Monitoring

Intership Safety

U.S. Coast Guard

Navigation

Port Operation

Noncommercial

Environmental

Commercial

Marine Operator

State Control

Weather

Download from Www.Somanuals.com. All Manuals Search And Download.

6-4

Appendix

Emergency

Calling

Channel 16, 9, and Working Channel

Channel 16

If:

- you wish to establish

communications with

another station

• Your ship is sinking, or on fire

• Someone has been lost overboard

• There exists grave and imminent And

danger

- you know which working

channel the station is

monitoring

Use this distress procedure:

• Select Channel 16

• Say "Mayday, Mayday, Mayday."

• Give call sign and boat name

• Give location of boat

Then

- initiate the call directly on

that working channel

- you wish to establish

communications with

another station

• Describe emergency

• If no answer, repeat; then try another

channel

And

- you do not know what

working channel the

station may be monitoring

- initiate the call on channel

16. After contact is made

switch to a working

channel.

Then

Caution

Every ship at sea is to obliged to give

absolute priority to radio

communications relating to ships in

distress - it is vital that false distress

calls or messages not be broadcast.

Note: Due to congestion on channel

16 caused by frequent hailing

of other vessels, the FCC has

approved channel 9 as a second

hailing channel.

Avoid excessive calling and radio

checks

Always monitor before transmitting

Never interrupt emergency

communications

Download from Www.Somanuals.com. All Manuals Search And Download.

6-5

Appendix

Monitoring

Intership Safety

Channel 16 and Working Channel

Channel:

Vessels:

Use:

When

- your VHF station is turned

on and it is not being used

to exchange

Any

Communicating

communications

navigational and weather

warnings to other ships

You Must - monitor channel 16

Communicating with U.S. Coast Guard

stations or other vessels during search

and rescue operations

As an operating convenience, many

stations employ a second receiver so

that they can monitor a working

channel and channel 16 simultaneously.

Between: Ship-to-ship only

Comments: Do not use for routine

communications. This is a

safety channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-6

Appendix

U.S. Coast Guard

Navigation

Channel:

Vessels:

Use:

Channel:

Vessels:

Use:

22A

Any

Working channel for

exchange of

Safety Communications

pertaining to the

communications with

stations of the U.S. Coast

Guard.

maneuvering of vessels or

the directing of vessel

movements

Between: Ship to U.S. Coast Guard

ship, coast to aircraft

stations

Ship-to ship and secondarily ship-to-

coast

This is commonly called the Bridge-to-

Bridge channel. Large vessels and

towboats depend on this channel for

their safe navigation. Railway or

highway bridges which open for ship

navigation often operate on this

channel.

Comments: U.S. Coast Guard does not

regularly monitor this

channel. Establish contact

on channel 16 and shift to

channel 22A as directed.

Bridge-to-Bridge stations must reduce

power to one watt for routine

operations.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-7

Appendix

Port Operations

Non commercial (Boat Operations)

Channels: 1A, 5A, 12, 14, 20A, 65A,

66A, 73, 74, 77

Channels: 9, 68, 69, 71, 72, 78A

Vessels:

Any

Vessels:

Use:

Recreational boats and any

others not used primarily

for commercial transport.

Use:

Messages relating to the

operational handling,

movement and safety of

vessels in or near ports,

locks and waterways.

Communications

pertaining to the needs of

the vessel (i.e., fishing,

rendezvous, maneuvers,

berthing, scheduling of

repairs, provisioning, etc.)

Between: Ship-to ship or ship-to-

coast

Between: Ship-to-ship or ship to

limited coast stations

Comments: Channel 77 is limited to

communications to and

Comments: Channel 72 may not be

used for ship to coast

communications. Channel

9 is shared with

from commercial pilots

concerning the movement

and docking of vessels.

Commercial users.

Note:

Channels 11, 12, 13 and 14

are used for vessels traffic

service on the Great Lakes,

St. Lawrence Seaway and

designated major ports.

If you regularly monitor one of these

channels with a second receiver, please

notify frequently-called stations of this

practice. Help reduce congestion on

channel 16.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-8

Appendix

Commercial

Marine Operator

Channels: 7A, 8, 9, 10, 11, 18A, 19A,

67, 79A, 80A, 88A

Channels: 24, 25, 26, 27, 28, 84, 85, 86,

Vessels:

Use:

Those used primarily for

commercial transport of

persons or goods, or

engaged in servicing other

vessels

Vessels:

Use:

Any

Communications

pertaining to the purpose

for which the vessel is

used

To place a telephone call to

any location in the world

or to a vessel outside of

your transmitting range

Between: Commercial transport

vessels (ship-to-ship) or

between commercial

Between: Vessels and public coast

stations

transport vessels and

limited coast stations

Comments: Contact the marine

operator on the channel

assigned to your

Channel 8, 67 and 88A may not be used

for ship-to-coast communications

navigating area. If unable

to determine this channel,

use channel 16.

Recreational boats are not permitted to

use these channels

Be patient. Do not interrupt calls in

progress. Avoid excessive calling if the

operator does not answer - give the

operator a chance to reply.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-9

Appendix

State Control

Environmental

Channel:

Vessels:

Use:

Channel:

State and local government Vessels:

Any (receive only)

Coordination, regulation

and control of boating

activities and the rendering

of assistance to vessels.

Use:

Broadcast of information

concerning the

environmental conditions

in which vessels operate -

weather, sea conditions,

time signals, notices to

mariner, hazards to

navigation

Between: Ship and coast stations

associated with state and

local governments.

Between: One-way broadcast from

coast to ship stations

Note:

Currently used for Class C

EPIRB emergency signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-10

Appendix

Weather

Channels: WX0—WX9

Vessels:

Use:

Any

Continuous weather

information from NOAA

(National Oceanic and

Atmospheric

Administration)

Between: One-way broadcast from

NOAA to any interested

parties

Comments: Receive only. You are not

permitted to transmit on

these frequencies.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-11

Appendix

PHONETICALPHABET:

To help make call letters more clearly understood, and to assist in spelling

out similar sounding or unfamiliar words, radiotelephone users employ the

international phonetic alphabet.

Phonetic Alphabet:

A - ALPHA

B - BRAVO

C - CHARLIE

D - DELTA

E - ECHO

F - FOX-TROT

G - GOLF

H - HOTEL

I - INDIA

J - JULIET

K - KILO

L - LIMA

M - MIKE

N - NOVEMBER

O - OSCAR

P - PAPA

Q - QUEBEC

R - ROMEO

S - SIERRA

T - TANGO

U - UNIFORM

V - VICTOR

W - WHISKEY

X - X-RAY

Y - YANKEE

Z - ZULU

Download from Www.Somanuals.com. All Manuals Search And Download.

6-12

Appendix

6.3

VHF Marine Channels Frequency Tables

International Mode

Note: International VHF frequency usage varies from country to country. Ensure you

are familiar with the channel requirements of the country where you are boating

before using any VHF transceiver.

International Mode

Frequency (MHz)

Channel

Number

Power

Type of Traffic

156.050

156.100

156.150

156.200

156.250

160.650 Public Correspondence (Marine Operator) Hi, Lo

160.700 Public Correspondence (Marine Operator) Hi, Lo

160.750 Public Correspondence (Marine Operator) Hi, Lo

160.800 Public Correspondence (Marine Operator) Hi, Lo

160.850 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

156.300

156.350

156.300

Intership Safety

Hi, Lo

160.950 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

156.400

156.450

156.500

156.550

156.600

156.650

156.700

156.750

156.800

156.850

156.900

156.400

Intership

Hi, Lo

156.450 Intership, Port Operations, Ship Movement Hi, Lo

156.500

156.550

156.600

156.650

156.700

156.750

156.800

156.850

Intership

Hi, Lo

Port Operations, Ship Movement

Intership Navigation, Safety

Port Operations, Ship Movement

On Board Communications, Intership

International Distress, Safety

On Board Communications, Intership

Hi, Lo

15 ¹

Hi, Lo

Lo Only

Hi, Lo

17 ¹

Lo Only

161.500 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

156.950

157.000

157.050

157.100

161.550 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

161.600 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

161.650 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

161.700 Public Correspondence (Marine Operator), Hi, Lo

Port Operations, Ship Movement

Download from Www.Somanuals.com. All Manuals Search And Download.

6-13

Appendix

Frequency (MHz)

Channel

Number

Power

Type of Traffic

157.150

157.200

157.250

157.300

157.350

157.400

156.025

161.750

161.800

161.850

161.900

161.950

162.000

160.625

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

156.075

156.125

156.175

156.225

156.275

156.325

160.675

160.725

160.775

160.825

160.875

160.925

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

Public Correspondence (Marine Operator) Hi, Lo

Port Operations, Ship Movement

156.375

156.425

156.475

156.575

156.625

156.675

156.725

156.875

156.925

156.975

157.025

157.075

157.125

157.175

157.225

157.275

157.325

156.375

156.425

156.475

156.575

156.625

156.675

156.725

156.875

161.525

161.575

161.625

161.675

161.725

161.775

161.825

161.875

161.925

Intership, Port Operations

Hi, Lo

Port Operations, Ship Movement

Intership, Port Operations, Ship Movement Hi, Lo

Port Operations, Ship Movement Hi, Lo

Intership, Port Operations, Ship Movement Hi, Lo

Port Operations, Ship Movement

Hi, Lo

Intership

Public Correspondence, Port Operations

Download from Www.Somanuals.com. All Manuals Search And Download.

6-14

Appendix

Frequency (MHz)

Channel

Number

Type of Traffic

Power

87A

88A

157.375

157.425

157.375

157.425

Public Correspondence, Port Operations Hi, Lo

Notes:

1. For channels 15 and 17, output power is fixed at 1 watt only. Transmission at high

power is not permitted.

2. Channel 70 is used for Digital Selective Calling (DSC) only and is not available

for voice transmissions. Channel 70 does not appear on the display.

Important Notice

The International frequency mode is not legal for use while operating in U.S. waters.

The TX/RX frequencies available in International frequency mode were agreed upon

by the attending countries at the 1968 ITU-International Telecommunication Union

meeting in Geneva, and are legal for use in International waters only.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-15

Appendix

Canadian Mode Frequency Table

Canadian Mode

Frequency (MHz)

Power

Channel

Number

Type of Traffic

156.050

156.100

156.150

156.200

160.650 Public Correspondence (Marine Operator) Hi, Lo

160.700 Public Correspondence (Marine Operator) Hi, Lo

160.750 Public Correspondence (Marine Operator) Hi, Lo

04A

156.200

Pacific Coast: Canadian Coast Guard

East Coast: Commercial Fishing Only

Hi, Lo

05A

156.250

156.300

156.350

156.400

156.450

156.250

156.300

Ship Movement

Intership Safety

Hi, Lo

07A

156.350 Commercial

156.400 Commercial (Intership Safety)

156.450 Boater Calling Channel, Commercial and Hi, Lo

Non-Commercial

156.500

156.500 Ship Movement, Commercial and

Non-Commercial (Intership Safety)

Hi, Lo

156.550

156.600

156.650

156.700

156.750

156.800

156.850

156.900

156.950

157.000

157.050

157.100

156.550 Port Operations, Ship Movement

Hi, Lo

156.600

156.650 Intership Navigation (Bridge to Bridge)

156.700 Port Operations, Ship Movement

156.750 On Board Communications

156.800

Port Operations, Ship Movement

13 ¹

Hi, Lo

Lo Only

15 ²

International Distress, Safety, and Calling Hi, Lo

17 ²

18A

19A

156.850 On Board Communications

Lo Only

Hi, Lo

156.900 Commercial, Towing on Pacific Coast

156.950 Canadian Coast Guard Only

161.600 Port Operation with 1 watt max. power

157.050 Canadian Coast Guard Only

21A

22A

157.100 Communication between Canadian Coast Hi, Lo

Guard and non-Canadian Coast Guard

157.150

161.750 Public Correspondence on Pacific Coast

and Inland Waters of BC and the Yukon

Hi, Lo

157.200

157.250

161.800 Public Correspondence in all areas

Hi, Lo

161.850 Public Correspondence on Pacific Coast

and Lake Winnipeg

157.300

157.350

161.900 Public Correspondence, Safety

Hi, Lo

161.950 Public Correspondence on Pacific Coast,

Atlantic Coast, and Great Lakes

Download from Www.Somanuals.com. All Manuals Search And Download.

6-16

Appendix

Frequency (MHz)

Channel

Number

Type of Traffic

Power

157.400

156.025

156.075

162.000

160.625

156.075

Public Correspondence on Pacific Coast

Public Correspondence

Hi, Lo

61A

Pacific Coast: Canadian Coast Guard

East Coast: Commercial Fishing Only

62A

156.125

Pacific Coast: Canadian Coast Guard

East Coast: Commercial Fishing Only

Hi, Lo

64A

65A

156.225

156.275

156.225 East Coast: Commercial Fishing

Hi, Lo

156.275

Great Lakes: Search & Rescue

Antipollution Operations

Pacific Coast: Towing

St. Lawrence River Area: Port Operations

(restricted to 1 watt)

66A

156.325

156.375

156.325

St. Lawrence River / Great Lakes Areas:

Port Operations Only (restricted to 1W)

Hi, Lo

156.375 Search & Rescue, Antipollution Operations Hi, Lo

East Coast Only: Commercial Fishing

156.425

156.475

156.425

156.475

Non-Commercial, Marinas & Yacht Clubs Hi, Lo

Commercial and Non-Commercial

East Coast Only: Commercial Fishing

Hi, Lo

156.575

156.625

156.675

156.575 Commercial and Non-commercial

156.625 Maritime Support Operation

Hi, Lo

156.675 Search & Rescue, Antipollution Operations Hi, Lo

East Coast Only: Commercial Fishing

77 ²

78A

79A

80A

81A

82A

83A

156.725

156.875

156.925

156.975

157.025

157.075

157.125

157.175

157.225

157.275

157.325

157.375

157.425

156.725

156.875

156.925

156.975

157.025

157.075

157.125

157.175

161.825

161.875

161.925

161.975

162.025

Ship Movement

Hi, Lo

Lo Only

Hi, Lo

Ship Movement, Intership Safety

Commercial

Canadian Coast Guard Only

Public Correspondence (Marine Operator) Hi, Lo

Download from Www.Somanuals.com. All Manuals Search And Download.

6-17

Appendix

Important Notice

The Canadian frequency mode is not legal for use while operating in U.S. waters.

Notes:

1. For channel 13, output power is fixed at 1 watt (low power) by regulation. In an

emergency, you can override to high power by pressing and holding PTT and

then pressing the MON/ 1/25 key on the base station. Output power is increased

to 25 watts while both keys are pressed. After MON/1/25 is released, power

returns to 1 watt.

2. For channels 15, 17, and 77, output power is fixed at 1 watt only. Transmission at

high power is not permitted.

3. Channel 70 is used for Digital Selective Calling (DSC) only and is not available

for voice transmissions. Channel 70 does not appear on the display.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-18

Appendix

US Mode Frequency Table

US MODE

Frequency (MHz)

Channel

Power

Type of Traffic

Number

01A

156.050

Port Operations and Commercial,

VTS in selected areas

Hi, Lo

03A

05A

156.150

156.250

156.300

156.350

156.400

156.450

156.150

US Government and Coast Guard

Hi, Lo

156.250 Port Operations, VTS in selected areas

156.300 Intership Safety

07A

156.350 Commercial

156.400 Commercial (Intership only)

156.450

Boater Calling, Commercial and non-

Commercial

156.500

156.550

156.600

156.650

156.500 Commercial

Hi, Lo

156.550 Commercial, VTS in selected areas

156.600 Port Operations, VTS in selected areas

13 ¹

156.650

Intership Navigational Safety (Bridge to

Bridge)

15 ²

17 ³

18A

19A

20A

21A

22A

156.700

—

156.700 Port Operations, VTS in selected areas

156.750 Environmental (Receive only)

Hi, Lo

—

156.800

156.850

156.900

156.950

157.000

157.050

157.100

156.800

International Distress, Safety, and Calling Hi, Lo

156.850 State Controlled

156.900 Commercial

Lo only

Hi, Lo

156.950 Commercial

157.000 Port Operations

157.050 Coast Guard only

157.100 Coast Guard Liason and Maritime Safety Hi, Lo

Info. Broadcasts announced on CH 16.

23A

157.150

157.200

157.250

157.300

157.350

157.400

156.075

156.175

157.150 Coast Guard only

Hi, Lo

161.800 Public Correspondence (Marine Operator) Hi, Lo

161.850 Public Correspondence (Marine Operator) Hi, Lo

161.900 Public Correspondence (Marine Operator) Hi, Lo

161.950 Public Correspondence (Marine Operator) Hi, Lo

162.000 Public Correspondence (Marine Operator) Hi, Lo

156.075 US Government and Canadian Coast Guard Hi, Lo

61A

63A

156.175 Port Operations and Commercial.

VTS in selected areas.

Hi, Lo

64A

65A

156.225

156.275

156.225 US Government

156.275 Port Operations

Hi, Lo

Download from Www.Somanuals.com. All Manuals Search And Download.

6-19

Appendix

Frequency (MHz)

Channel

Number

Power

Type of Traffic

Port Operations

66A

67 ¹

156.325

156.375

156.425

156.475

156.575

156.625

156.675

156.725

156.875

156.925

156.975

157.025

157.075

156.325

Hi, Lo

156.375 Commercial, Bridge-to-Bridge (Intership) Lo only

156.425

156.475

156.575

156.625

156.675

156.725

156.875

156.925

156.975

157.025

157.075

Non-Commercial

Hi, Lo

Lo only

Hi, Lo

Non-Commercial

Non-Commercial (Intership Only)

Port Operations

77 ³

78A

79A

80A

81A

Port Operations (Intership Only)

Non-Commercial

Commercial

US Government Only: Environmental

Protection Operations

82A

83A

157.125

157.175

157.225

157.275

157.325

157.375

157.425

157.125

157.175

161.825

161.875

161.925

161.975

157.425

US Government Only

US Coast Guard Only

Hi, Lo

Public Correspondence (Marine Operator) Hi, Lo

88A

Commercial (Intership Only)

Hi, Lo

Notes:

1. For channels 13 and 67, output power is fixed at 1 watt (low power) by regulation.

In an emergency, you can override to high power by pressing and holding PTT

and then pressing the MON/1/25 key on the base station. Output power is increased

to 25 watts while both keys are pressed. After MON/1/25 is released, power

returns to 1 watt.

2. Channel 15 is receive only. Transmission is not permitted.

3. For channels 17 and 77, output power is fixed at 1 watt only. Transmission at

high power is not permitted.

4. Channel 70 is used for Digital Selective Calling (DSC) only and is not available

for voice transmissions. Channel 70 does not appear on the display.

Important Notice

Channels 3A, 21A, 23A, 61A, 64A, 81A, 82A, and 83A (shaded) are not for use by the

general public in U.S. waters. These frequencies may be used only under authorization

by the U.S. Coast Guard or under private land mobile license.

Download from Www.Somanuals.com. All Manuals Search And Download.

6-20

Appendix

Weather Channels and Frequencies

RX Frequency

162.550

162.400

162.475

162.425

162.450

162.500

162.525

161.650

161.775

163.275

Type of Traffic

Weather

Transmission Type

Receive only

Important Notice

The US National Oceanic and Atmospheric Administration (NOAA) broadcasts

continuous weather reports and severe weather alerts, as needed. The RAY215 is

programmed to receive 10 NOAA weather channels and sound an alarm if a weather

alert is received.

Weather operation is available only in US frequency mode and can only be heard in

the US and Canada.

Download from Www.Somanuals.com. All Manuals Search And Download.

Raypak Boiler Gas Fired Boiler User Guide
RCA Flat Panel Television 46LA45RQ User Guide
Renesas Computer Hardware H8SX1664 User Guide
ResMed Respiratory Product Bilevels User Guide
Rinnai Water Heater REU V2526W US User Guide
Saeco Coffee Makers Coffeemaker HD8772 User Guide
Samson Headphones SWC99BGT K; SWC99BGT I User Guide
Samsung Projector BP59 00143A 04 User Guide
Seal a Meal Food Saver VSA3 R User Guide
Senco Staple Gun SLS18Mg User Guide