INFORMATION TO USER
PRECAUTIONS
J
J
Safety Guard
In case of problem
Protect from high temperatures
Do not use the camera if smoke or strange odors come from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer or a Sanyo Authorized
Service Center.
Do not install close to stoves, or other heat generating devices,
such as spotlights, etc., or where it could be subject to direct
sunlight, as that could cause deformation, discoloration or other
damage.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels. Install where the
temperature range will stay between -10°C (14°F) and 50°C
(122°F). (no condensation)
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THIS UNIT.
INSTRUCTION MANUAL
(Warranty attached)
VCC-4344
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
J
Do not open or modify
COLOR CCD camera
Do not open the cabinet, as it may be dangerous and cause
damage to the unit. For internal settings and repairs, consult your
dealer or a Sanyo Authorized Service Center.
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
J
Cleaning
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Pour la clientèle canadienne
Cet appareil numerique de la Classe B est conforme a la norme NMB-003
du Canada.
J
Do not put objects inside the unit
Dirt can be removed from the cabinet by wiping it with a soft cloth.
To remove stains, use a soft cloth moistened with a soft detergent
solution and wrung dry, then dry by wiping with a soft dry cloth.
Do not use benzine, thinner or other chemical products on the
cabinet, as they may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes
in contact with the cabinet for extended periods, as that may
cause damage or paint peeling.
Make sure that no metal objects or flammable substances get
inside the camera. If used with a foreign object inside, it could
cause fire, short-circuits or damage. If water or liquid gets inside the
camera, disconnect the power cord immediately, and consult your
dealer or a Sanyo Authorized Service Center. Be careful to protect
the camera from rain, sea water, etc.
This installation should be made by a qualified service person and should
conform to all local codes.
Dimensions: mm
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
136
67
1
126.5
J
Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to strong
shock or vibration.
54
J
Install away from electric or magnetic fields
11
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, or audio speakers, the magnetic field they generate
will distort the image.
1/4”–20 UNC
28
15.4
25.2
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
J
Protect from humidity and dust
To prevent damage to the camera, do not install it where there is
greasy smoke or steam, where the humidity may get too high, or
where there is a lot of dust.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by Sanyo may void the user's
authority to operate this camera.
Depending on the conditions of use, installation and
environment, please be sure to make the appropriate settings
and adjustments. If you need help with installation and/or
settings, please consult your dealer.
Printed on recycled paper
1AC6P1P2705--
L5AN4/US (0307TR-SY)
SANYO Electric Co., Ltd.
Printed in Japan
NAMES AND FUNCTIONS OF PARTS
TROUBLESHOOTING
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your
place of purchase or a Sanyo Authorized Service Center.
SPECIFICATIONS
Scanning system
: NTSC standard TV system
Flange-back adjustment lever
(525 TV lines, 30 frames/sec.)
Flange-back lock screw
Interlace
: PLL 2:1 interlace
Image device
Picture elements
Effective picture
elements
: 1/4 inch solid state image device CCD
: 537 (H) x 505 (V)
: 510 (H) x 492 (V)
Lens cap
Protects the lens from damage.
J
If no image appears
G C B
Camera installation bracket
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly
(with the iris dial)?
The bracket can be secured at the top or bottom of the camera. When
securing the bracket, use the long screws and use the short screws on the
opposite side to seal the openings.
Synchronizing system : Internal sync, Line lock manually switchable
Resolution
: 350 TV lines horizontally (color mode),
380 TV lines horizontally (B/W mode),
350 TV lines vertically
c Short screws: M3 x 4
d Long screws: M3 x 6
Video output level
Video S/N ratio
Minimum required
illumination
: 1.0 Vp-p/75 ohms, composite
: More than 48 dB
: Approx. 0.05 lux with a F 1.2 lens (B/W mode),
Approx. 0.9 lux with a F 1.2 lens (color mode),
e Camera mounting screw hole: 1/4”-20 UNC
Is there adequate illumination?
J
If the image is unclear
Is the lens in focus?
(incandescent lighting) Approx. 0.02 lux with a F 1.2 lens (B/W mode, Gain: HI)
POWER (power indicator)
Lights when the camera power is ON.
When installing the camera support, select a location that can support the
total weight of the camera and accessories.
Day/Night
Control terminal
Backlight
: AUTO/MANUAL (at CONTROL terminal)
: Manual color/black and white setting
: MULTI/OFF switching
Is the lens dirty?
VIDEO OUT (video output terminal: BNC connector)
Connects to the VIDEO IN (video input) terminal on the VCR or monitor.
Dirt or fingerprints on the lens can adversely affect the image.
Gently wipe any dirt or fingerprints off the lens with a soft cloth or
lens cleaning paper and cleaning fluid (commercially available).
Is the monitor adjusted correctly?
Q
Attaching the lens
compensation
CENT/OFF switching
Use a DC type auto-iris lens (sold separately).
CONTROL (Manual color/black and white setting terminal)
G (ground) terminal
(Active when using an auto-iris lens)
Iris function
: EI/AI switching
C (color) terminal
Auto-iris lens output : DC output (variable DC level), 4-pin terminal
Electronic iris range : 0.9 lux to 45000 lux (F 1.2 lens: color mode)
B (black and white) terminal
Do not use a lens if length “L” is more than 5 mm.
Otherwise, it may damage the camera and prevent
proper installation.
When attaching a C mount lens, attach the lens to the
camera after inserting the C mount ring (option).
L
LINE PHASE (Line phase adjustment volume)
When using two cameras or more, the image on the monitor may roll
vertically when switching sources. This rolling can be minimized by turning
this volume.
Flange-back
White balance
Gain up
Lens mount
Environmental
conditions
: 12.5 mm ±0.5 mm
: ATW/Manual switching
SERVICE
The camera is a precision instrument. Handle it carefully and
always follow the safety precautions. If the camera requires service,
never try to repair it yourself or open the casing.
: HI (high)/ NOR (Normal) switching
: CS mount
: Temperature: -10°C – +50°C
Humidity: less than 90% (no condensation)
: 12 – 15 VDC/24 VAC, 60 Hz (±10%)
GND, AC24V, DC12V (ground terminal, 24V AC or 12V DC input
terminal)
1
Remove the lens mount
cap from the camera.
2
Power supply
Camera adjustment/setting panel
Contains camera adjustment dials and setting switches.
2
3
Install the auto-iris lens.
Power consumption : 3.2 W (with auto iris lens)
Weight : Approx. 430 g (without lens)
For servicing, maintenance, or repairs, contact your place of
purchase or a Sanyo Authorized Service Center.
3
1
Connect the lens plug to
the lens iris output
LENS (lens iris output terminal)
Used to connect the lens plug when the lens is attached.
connector (LENS) on the
side of the camera.
Appearance and specifications are subject to change without prior notice.
c Brake coil (-)
e Drive coil (+)
d Brake coil (+)
f Drive coil (-)
CS mount type lens
Download from Www.Somanuals.com. All Manuals Search And Download.
|