INSTRUCTION MANUAL
HDD/DVD Recorder
DVR-H200UK
Problems with set-up?
Call 0870 240 7475
Calls cost a maximum of 8p per
minute during peak periods,
based on BT rates of April 2004.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1) Read instructions. Read all the safety and operating
instructions before operating the product.
2) Retain instructions. Keep the safety and operating
instructions for future reference.
3) Heed warnings. Adhere to all warnings on the product and in
the operating instructions.
4) Follow instructions. Follow all operating and use
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
instructions.
5) Cleaning - Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
17) Lightning - For added protection of this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
18) Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
lights or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
take extreme care to keep it from touching power lines or
circuits. Contact with them might be fatal.
19) Overloading - Do not overload wall outlets, extension cords,
or integral convenience receptacles. This can result in a risk of
fire or electric shock.
20) Objects and Liquids - Do not push objects of any kind into
this product through openings. They may touch dangerous
voltage points or short out parts, resulting in a fire or electric
shock. Liquids of any kind should not be used on or around
this product.
6) Attachments - Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7) Water and Moisture - Do not use this product near water
for example, near a bathtub, washbowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool.
8) Accessories - Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions and should use a mounting accessory recom-
mended by the manufacturer.
9) CART - A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
10) Ventilation - Slots and openings in the cabinet provide
ventilation, ensure reliable operation of the product, and protect
it from overheating. Do not block or cover these openings. The
openings should never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. Do not place this
product in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
21) Servicing - Do not attempt to service this product yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
22) Damage Requiring Service - Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
11) Power Sources - This product should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer
to the operating instructions.
• When the power supply cord or plug is damaged,
• If liquid has spilled or objects have fallen into the product,
• If the product has been exposed to rain or water,
• If the product does not function properly after following the
operating instructions, contact Customer Service for technical
support.
12) LOCATION - The appliance should be installed in a stable
location.
13) NONUSE PERIODS - The power cord of the appliance
should be unplugged from the outlet when left unused for a
long period of time.
• If the product has been dropped or damaged in any way,
• When the product exhibits a distinct change in performance.
This indicates a need for service.
23) Replacement Parts - When replacement parts are required,
be sure the service technician uses replacement parts
specified by the manufacturer or having the same characteris-
tics as the original part. Unauthorized substitutions may result
in fire, electric shock, or other hazards.
24) Safety Check - Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
25) Wall or Ceiling Mounting - Mount the product to a wall or
ceiling only as recommended by the manufacturer.
26) Heat - Keep this product away from heat sources, such as
radiators, heat registers, stoves, or amplifiers.
27) Battery Usage - Battery leakage may result in bodily injury or
damage to the unit. In order to avoid battery problems, please
follow these instructions.
14) Grounding or Polarization -
• If this product is equipped with a polarized alternating current
line plug (a plug having one blade wider than the other), it will fit
into the outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
• If this product is equipped with a three-wire grounding type plug,
it will only fit into a grounding type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding type plug.
15) Power-Cord Protection - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point
where they exit from the product.
• Install all batteries correctly, with + and - aligned as marked on
the unit.
• Do not mix batteries (old/new, carbon/alkaline, etc.).
• Remove batteries when the unit is not used for a long time.
16) Outdoor Antenna Grounding - If an outside antenna or
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS, CAUTIONS AND OTHERS
IMPORTANT FOR LASER PRODUCTS
1)CLASS 1 LASER PRODUCT
2)DANGER: Visible and invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
3)CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to qualified
service personnel.
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER OF THIS UNIT.
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION!
• CD-R/RW discs recorded using a personal computer or a CD
Recorder may not play if the disc is damaged or dirty, or if there
is dirt or condensation on the player’s lens.
• Unfinalized CD-R/RW discs can be played, but not all time
information (playing time, etc.) will be displayed.
• Check the copyright laws in your country before recording from
DVD VIDEO, SVCD, Video CD, Audio CD, MP3 and JPEG discs.
Recording of copyrighted material may infringe copyright laws.
The lighting flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to humans.
Legal Notices Regarding
Macrovision’s Property Rights
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the appliance.
“U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093;
and 6,516,132.”
“ This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited. “
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT
OPEN THE COVER AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
WARNING:
TOREDUCETHERISKOFFIRE, ELECTRICSHOCKOR
PRODUCTDAMAGE, DONOTEXPOSETHISAPPARATUS
TOMOISTURE ANDENSURETHAT OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED AWAY
FROMTHEAPPARATUS.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems Inc.
This unit complies with the European Directives 89/336/EEC and
73/23/EEC.
The apparatus shall not be exposed to dripping or splashing.
No objects filled with liquids, such as vases, shall be placed on
the apparatus.
CAUTION! –– STANDBY/ON button
Disconnect the main plug to shut the power off
completely. The STANDBY/ON button in any position
does not disconnect the main line. Power can be
controlled from the remote.
PRODUCTS WITH 625P PROGRESSIVE SCAN OUTPUTS
NOTICE REQUIREMENTS
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINI-
TION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS
PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN
THE PICTURE. IN CASE OF 625 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE “STANDARD DEFINITION”
OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV
SET COMPATIBILITY WITH THIS MODEL 625P DVD PLAYER,
PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.”
VIDEO Plus+ and PlusCode are registered trademarks of Gemstar
Development Corporation. The VIDEO Plus+ system is manufac-
tured under license from Gemstar Development Corporation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC INFORMATION
ꢀPlayable Disc types
Disc Types
Logos
Characteristics
This unit can playback DVD-Video discs and the
region code is printed on the rear of the unit.
DVD-VIDEO
DVDЁR, DVDЁRW and DVDЀR, DVDЀRW, discs
DVDЀR/ЀRW
written in the DVD-Video format and finalized.
DVDЁR/ЁRW
Video with CD sound, VHS quality, MPEG-1
MPEG-2 compression technology.
&
Video CD (VCD)
Super Video CD (SVCD)
CD is recorded as a Digital Signal with better audio
quality, less distortion and less deterioration of audio
quality over time.
Audio CD
This unit can play CD-R and CD-RW discs recorded
with Audio CD or Video CD format, or with
JPEG/BMP/MP3 files. Close the sessions or finalize
the disc after recording.
CD-R/RW
(JPEG/BMP/MP3)
ꢀRecordable Disc types
Disc Types
Logos
Characteristics
DVDЀR/ЀRW
DVDЀR disc written in the DVDЀVR format.
DVDЀRW disc written in the DVDЀVR format.
CDЁR/ЁRW
CDЁR/CDЁRW disc written in the MPEG1 or
MPEG2 video format or written in PCM Audio mode.
Note:
ꢀAudio System
Dolby Digital
DTS (Digital Theater Systems)
The DVD-Video/DVD+RW/DVD+R/DVD-R/DVD-RW Logos
are trademarks of the respective companies.
Linear PCM
For best results, use discs with the above logos. The unit
may not playback other discs correctly. Do not use irregular-
shaped discs (e.g. heart-shaped), as these can damage the unit.
It may not be possible to play CD-R, CD-RW, DVD-R, DVD-
RW, DVD+R, DVD+RW in all cases due to the type of disc or
condition of the recording.
ꢀVideo System ( PAL )
This DVD recorder accepts PAL system.
Unplayable disc types
The unit does not play back disc type listed below. If you
try to play back these discs, excessive noise may cause
damage to your speakers.
ꢀAspect Ratio
4:3 (Letter Box) Standard
1) Unfinalized discs from other DVD/CD recorders.
2) DVD AUDIO, PHOTO CD, SACD, HDCD
4:3 Pan & Scan
(When placing an unplayable disc on the disc tray, the DVD
recorder will display “Unknown Disc” on the display panel after
attempts of trying to loading the disc fail.)
16:9 (Wide-Screen)
ꢀRegion code of DVD-Video
ꢀOthers
This unit can play back DVD-VIDEO discs compatible with
the region code printed on the rear of the unit.
Audio : Appears at the beginning of a scene recorded
with multiple audio languages.
Example of playable DVD-VIDEO discs:
Subtitle: Appears at the beginning of a scene recorded
with multiple subtitle languages.
If you try to play any other discs, the message “Invalid
Region Code” will apear on TV screen.s:
Angle : Appears at the beginning of a scene recorded
from multiple angles.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND DISPLAYS
The Remote Control
Remote Control
1) Timer button (TIMER)
2) Open / Close button ( OPEN / CLOSE)
3) VIDEO Plus+ button (VIDEO Plus+)
4) Stop button ( STOP)
Play button ( PLAY)
Pause / Step button (ꢀPAUSE / STEP)
5) REV/ FF buttons (
Skip buttons (
REV /
PREV /
FF)
NEXT)
6) Display button (DISPLAY)
7) Disc Menu button (DISC MENU)
8) Edit button (EDIT)
9) Cursor (ꢀꢁꢂꢃ), Enter buttons (ENTER)
10) Copy button (COPY)
11) Number buttons (1~9,0)
12) Easy Guider Menu button (GUIDER)
Browser button (BROWSER)
Disc Tools button (TOOLS)
Navigation button (NAVI)
13) Audio button (AUDIO)
Angle button (ANGLE)
To install batteries
ꢁ
Open the battery compartment and
insert the batteries. Make sure the
polarities (+ and -) match the marks
indicated inside the remote control.
Zoom button (ZOOM)
Subtitle button (SUBTITLE)
14) Source button (SOURCE)
ꢁ
Do not use rechargeable type
batteries.
15) Power button (
STANDBY/ON)
Remote sensor
16) HDD/DVD button (HDD/DVD)
The remote has a range of
approximately 7M and works
best when pointed directly at
the unit horizontally at angles
up to 30° from the front of the
unit.
17) Record button ( REC)
ꢁ
18) Play List Menu button (PLAY LIST MENU)
19) Record Mode button (REC MODE)
20) Time shift button (TIME SHIFT)
21) CH Up / Down buttons (CH+ / CH-)
22) Setup button (SETUP)
Do not dispose of the batteries in your domestic or any
other waste bin! Instead, bring them to the nearest
collection site, e.g. at your retail dealer or supermarket:
you will find special collection boxes there for used
batteries. All collected batteries will be recycled.
Please help to conserve our environment. Thank you.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND DISPLAYS
Front panel connections
7) DISPLAY Window
Names of parts and controls
1) POWER ON/OFF Button ( /ON)
Operation indicators are displayed here.
8) DV IN Jack
Turns the recorder on and off.
Connects digital video camcorders to this DVD Recorder.
2) DISC TRAY
Holds discs securely during recording or playback.
9) OPEN/CLOSE Button ( OPEN / CLOSE)
Opens or closes the disc tray.
3) RECORD Button ( REC)
ꢁ
Starts recording.
10) PLAY Button ( PLAY)
Plays a disc.
4) DVD Indicator
Lights up when DVD is set as the playback/record
device.
11) STOP Button ( STOP)
Stops playing or recording a disc.
5) HDD Indicator
12) HDD/DVD Button ( HDD/DVD )
Lights up when HDD is set as the playback/record
device.
Press to switch between HDD and DVD.
13) VIDEO IN/AUDIO IN L/R Jacks
6) SOURCE Button (SOURCE)
Connect the output of external equipment.
Selects equipment connected to the line inputs.
Display window
1) Play indicator
2) DVD indicator
3) SVCD indicator
4) VCD indicator
5) CDDA indicator
6) FILE indicator
7) CD indicator
8) DVD+R indicator
9) Pause indicator
10) Record indicator
11) Timer record mode
12) Multi-information window
13) DVD+RW indicator
14) CD-R/DVD-R indicator
15) CD-RW/DVD-RW indicator
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND DISPLAYS
Rear panel connections
Names of parts
1) TUNER(RF OUT/RF IN) Jacks
Antenna cables input and output.
5) COMP OUT Jacks
Component signal output.
Note: DVD signals don’t go through here. Make
proper connections before use.
6) DIGITAL OUT (COAXIAL) Jack
Connect to an amplifier or a receiver having a
digital input jack.
2) SCART IN Jack
Composite/RGB signal input.
7) DIGITAL OUT (OPTICAL) Jack
Connect to an amplifier or a receiver having a
digital input jack.
3) SCART OUT Jack
Composite/RGB/S-Video signal output.
8) AC IN Terminal
4) AV OUTPUT Jacks
Connect the power cord.
Composite signal output.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Before making connections
1) Do not plug the AC power cord into the outlet until all other connections are made.
2) Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the unit to a TV via a VCR may
cause a viewing problem when playing back a copy-protected disc. You may also have a viewing problem when connecting
the unit to an integrated TV/Video system.
Connecting to the antenna outlet and the television
Before using the unit, follow the steps below to connect the unit to the antenna cable and TV.
Connecting to a TV with SCART jack
Use the antenna cable (supplied) to connect the RF IN on the unit to the antenna outlet.
Use the antenna cable (not supplied) to connect the RF OUT on the unit to the RF input on the television.
Use a SCART cable to connect the SCART OUT jack on the unit to the SCART IN jack on the television.
Notes:
1. Do not place this unit on top of other equipment that may generate heat. Excessive heat may cause this unit to
malfunction.
2. For Digital Cable and Satellite TV users please connect your decoder’s output to this unit’s input.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR BETTER VIDEO QUALITY
If your TV has Component Video inputs, you can enjoy superior picture quality.
Connecting to a TV via COMPO OUT
Connecting to a TV with component jacks
Use COMPONENT cable (not supplied) to connect the COMPO OUT on the unit to the COMPONENT input on the television.
Notes:
1. Enter system setup to enable COMPO OUT (refer to the section titled “Quick Setup”).
2. When using COMPO OUT connections, please remove all other video output connections.
3. In this configuration, the Red and White audio connections are required.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR BETTER AUDIO QUALITY
There are two types of audio connections, analog and digital.
Connecting to a stereo audio amplifier or receiver
Use an audio cable to connect the L/R AV OUTPUT on the unit to
the audio inputs on a stereo amplifier or a receiver.
Connecting to a digital audio device
Connect an amplifier with Dolby Digital and DTS decoders to enjoy surround sound.
Digital out optical
Use an optical digital cable (not supplied) to connect
the DIGITAL OUT OPTICAL (digital optical output) on
the unit to the digital optical input on an stereo amplifier
or a receiver.
Digital out coaxial
Use a coaxial digital cable (not supplied) to connect the
DIGITAL OUT COAXIAL (coaxial digital output) on the unit
to the coaxial digital input on an stereo amplifier or a
receiver.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Remote Control & Setup menu
Progressive Scan mode
You can change the video output mode when you press
[SETUP] and select “System-->Video Output-->
Follow the steps below to reset personal preferences for using
the DVD recorder. Confirm that all connections are secured
properly.
Progressive.”
Video output mode:
576i: Interlace video
1. Press [
STANDBY/ON] to turn on the unit.
2. Press [SETUP] to display the system menu.
3. Press [ꢀ] [ꢁ] to select “System,” “Language,”
“Playback,” “Record,” “Audio,” “TV Tuner” or “Exit”
and press [ꢂ ] or [ꢃ] to move to the next or
previous menu.
576p: Progressive video
4. Press [ꢀ ] [ꢁ] to select the item you want to
change.
(Refer to the “GUI operation” section for detailed menu)
5. Press [ENTER] to confirm the setting.
6. Press [SETUP] to exit the setup menu or press [ꢂ]
to return to the previous menu.ot
You must connect the component output on the unit to a
576p compatible television.
Note:
If you accidentally set “Progressive” as the Video Output
when not connecting to a progressive scan-compatible TV,
you may lose the video signal on your TV instantly. To get the
picture back, press [ꢃ(Cursor Right)] and the numbered
buttons “5,” “0,” “2” and “0” on the remote control and then
[ENTER]. In about 8 seconds, you can re-set the video output.
Notes:
1. To record TV programs using the Timer Record feature,
you must set the time accurately.
2. Please see also “ GUI(Graphical User Interface) Operation“
on page 42/43 for further information.
Setting Aspect ratio
Press [SETUP] and select “Playback”-->”Aspect Ratio.”
Setting the date and time
Check that the clock is correctly set before initiating the timer
recording function. If the clock is set incorrectly, Timer Record
results may not be accurate.
Select “4:3” (regular) or “16:9” (widescreen) to suit your
television. If you have a regular 4:3 television, you can also
select how video title on some discs is presented.
4:3 L.Box (4:3 Letter Box)
Select when you connect the unit to a
normal (4:3) TV.
When playing back a DVD-VIDEO disc
recorded in wide picture format, the picture
is shown with black bars at the top and bottom.
Set the date
1. Press [SETUP] and the setup menu will
be displayed.
2. Select “System” using [ꢀ] or [ꢁ] and press [ENTER].
3. Select “Date” using [ꢀ] or [ꢁ] and press [ENTER].
4. Change the day/month/year in the highlighted field using [ꢀ]
or [ꢁ] or the numbered buttons (0~9) on your remote
control and confirm by pressing [ENTER].
5. When all settings are correct, press [ꢂ] to return to the
main menu.
4:3 Pan (4:3 Pan & Scan)
Select when you connect the unit to a
normal (4:3) TV.
When playing back a DVD-VIDEO disc
recorded in wide picture format, the picture
6. To exit the setup menu, press [SETUP].
is zoomed to fill the screen vertically, and
the left and right sides of the image are chopped off. Note,
however, that the picture will be shown in the 4:3 L.Box (4:
3 Letter Box) mode even if you select the 4:3 Pan (4:3 Pan &
Scan) mode depending on the disc.
Set the time
1. Press [SETUP]. The setup menu will appear.
2. Select “System” using [ꢀ] or [ꢁ] and press [ENTER].
3. Select “Time” using [ꢀ] or [ꢁ] and press [ENTER].
4. Change the “hour/minute/second” in the highlighted field
using [ꢀ] or [ꢁ] or the numbered buttons (0~9) on your
remote control.
16:9 Wide (16:9 Wide Screen)
Select when you connect the unit to
a wide-screen (16:9) TV.
5. When all settings are correct, press [ꢂ] until returning to
the main menu.
6. To exit the setup menu, press [SETUP].
Setting Audio
Press [SETUP] and select “Audio.”
Digital Output
Notes:
Setting video output
PCM
Bit Stream
(Enable digital audio output with PCM or encoded data)
DTS Out
1. Press [SETUP] and the setup menu will be displayed.
2. Select “System” using [ꢀ] or [ꢁ] and press [ENTER].
3. Select “Video Output” as “Scart S-Video,” “Scart RGB”
“Component” or “Progressive” using [ꢀ] or [ꢁ] and press
[ENTER]. (Refer to “GUI operation” section for details)
4. When all settings are correct, press [ꢂ] to return to the
main menu.
On / Off
Surround
Stereo
DOLBY
DTS
TV sound Bilingual
Main
MPEG
PCM
Sub
5. To exit the setup menu, press [SETUP].
Bit Stream
Note:
When stereo broadcasting is received, L, R or MONO cannot
be selected for output audio.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TV CHANNEL SETUP
9. The channel scanning starts. This process may
take a few minutes.
10.When all the TV channels have been searched
and stored, press [SETUP] to exit.
TV channel scanning
When the “Scan Channel” function is activated, the TV
channels are searched and stored in a specific order. If the
channel assignment of your TV content provider is changed
or if you are reinstalling this DVD recorder, you may need to
start this procedure again.This will replace the TV channel
stored with the new ones.
Notes:
1. If the available channel number in your residence area
exceeds the maximum receivable channel numbers of this
DVD Recorder, the scan will be discontinued. The maxi
mum receivable channel numbers are:
Before scanning channel, set the “TV Signal” and “Country”
for initiation.
1. Ensure the antennas are securely connected to
the DVD recorder.
2. Switch on the TV set and the DVD recorder.
3. Press [SETUP] to display the setup menu, press
[ꢀ] or [ꢁ] to select the “TV Tuner” icon and
press [ꢃ].
Antenna:
Cable:
Auto:
168 (chs)
104 (chs)
176 (chs)
2. It would take more time for auto channel scanning
depending on the receiving condition of your antenna.
Fine-tuning TV channels manually
4. Press [ꢀ] / [ꢁ] to select “TV Signal” and press
After you have performed the channel scanning, you may like
to fine-tune the TV channel signal manually. Follow the steps
below to complete fine tune.
[ꢃ].
5. Press [ꢀ] / [ꢁ] to select “Cable,” “Antenna” or
“Auto” depending on how you receive your
terrestrial TV channels and press [ENTER]. Press
[ꢂ] to return to the previous menu and save the
setting.
1. Press [SETUP] to display the “Setup”, press
[ꢀ] or [ꢁ] to select the “TV Tuner” icon and
press [ꢃ].
2. Press [ꢀ] or [ꢁ] to select “Fine Tune” and
press [ꢃ].
If you select “Auto,” the unit will automatically scan both
channels available at cable and antenna connections, which
might take longer than needed.
3. Press [ꢀ] or [ꢁ] to fine-tune the channel signal.
4. When complete, press [SETUP] to exit the
setup menu.
6. Press [ꢀ] / [ꢁ] to select “Country” and press
[ꢃ]. Press [ꢀ] / [ꢁ] and [ENTER] to select the
country of your residence from the list . Press [ꢂ]
to return to the previous menu and save the
setting.
Editing TV channels manually
After you have performed channel scanning, you may like to
further edit the TV channels. This function allows manually
adding/deleting channels, swapping channel order, inserting
a channel to a specific order, renaming the channels and so
on.
1. Press [SETUP] to display the “Setup”, press
[ꢀ] or [ꢁ] to select the “TV Tuner” icon and
press [ꢃ].
2. Press [ꢀ] or [ꢁ] to select “Utilities” and press
7. Press [ꢀ] / [ꢁ] to select “Utilities” and press [ꢃ].
[ꢃ].
8. Press [ꢀ] / [ꢁ] to select “Scan Channel” and
press [ENTER] to start channel scanning.
3. Press [ꢀ] or [ꢁ] to select “Edit Channel” and
press [ENTER]. The CHANNEL EDITOR menu will be
displayed.
If you wish to stop scanning, move to “Stop Scan” and press
[ENTER]. The scanning process will be discontinued.
For detailed operation instructions on the “Channel Editor”
menu, refer to the “CHANNEL EDITOR” section.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL EDITOR
To access to the Channel Editor menu, press [SETUP], select
“TV Tuner,” “Utilities,” “Edit Channel” and press [ENTER]. Or,
press [SOURCE] to set “TV” as the input signal source and
press [EDIT]. Either way, the Channel Editor menu will be
displayed.
Swapping TV channels
This function allows you to manually swap the TV channel
order stored in the unit to match the TV channel order stored
in your TV set.
1. Press [ꢀ] [ꢁ] to select a TV Channel and press
Moving up or moving down the TV channel
[ꢃ].
1.Press [ꢀ] [ꢁ] to select one of the TV channels
and press [ꢃ].
2. Press [ꢀ] [ꢁ] to select “Swap With” and press
[ENTER].
2.Press [ꢀ] [ꢁ] to select “Move Up” or “Move
Down” and press [ENTER].
3. Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to enter the “Channel
number,” and press [ENTER] to swap. The order
of the channels will be swapped with the channel
number entered.
4. To swap other TV channels, repeat step 1~3 to
complete the settings.
The order of the TV channel will be changed.
Each time you press [ꢀ] or [ꢁ] and the item changes as
follows:
5. Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNELEDITOR”menu.
3. To move the location of other TV channels, repeat
step 1~2 to complete the settings.
4. Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNELEDITOR”menu.
Inserting TV channels
1. Press [ꢀ] [ꢁ] to select a TV channels and
press [ꢃ].
2. Press [ꢀ] [ꢁ] to select “Insert To” and press
[ENTER].
3. Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to enter the “Channel
number,” and press [ENTER]. The channel will be
moved to the desired location.
Renaming TV channels
1. Press [ꢀ] / [ꢁ] to select a TV channel and press
[ꢃ].
2. Press [ꢀ] [ꢁ] to select “Rename” and press
[ENTER].
The display for
entering a title name
appears.
3. Select the desired
characters from the
keypad. Press
[ENTER] after each
entry.
4. When you finish
entering the title name, press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to
select “Finish” and press [ENTER].
4. To change the locations of other TV channels,
repeat step 1~3 to complete the settings.
5. Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNELEDITOR”menu.
Notes:
1. You can only enter up to 10 characters for a name.
2. If you wish to enter “space”, select a blank on the keypad
and press [ENTER].
13
Download from Www.Somanuals.com. All Manuals Search And Download.
®
CHANNEL EDITOR
Setting up VIDEO Plus+ system
Turning on or turning off TV channels manually
Thanks to this programming system, you no longer need to
tediously enter the date, programme number, start and end
times. All the information needed by the DVD recorder for
After you have performed the channel scanning process, you
may like to add or delete some of the TV channels. This function
allows turning on the channel not found at channel scanning or
turning off the channel found manually.
®
programming is contained in the VIDEO Plus+ programming
number. This 9-digit PlusCode number is found in most TV
listings magazines.
Before setting up, confirm that the all cables are securely
connected.
1. Press [ꢀ] [ꢁ] to select a TV Channel not found at
channel scanning and press [ꢃ].
®
2. Press [ꢀ] [ꢁ] to select “Turn On” and press
[ENTER]. The TV channel selected will be turned
on.
Setting up the VIDEO Plus+ system
1. Press [SOURCE] to set TV as the input signal
source.
To turn off the TV channel, move to “Turn Off” and press
[ENTER]. The TV channel selected will be turned off.
2. Press [EDIT] to display the “CHANNEL EDITOR”
menu.
3. To turn on other TV channels, repeat step 1~2 to
complete the settings.
4. Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNELEDITOR”menu.
3. Press [ꢀ] [ꢁ] to go to a channel and press
[ENTER].
4. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to go to “GCN” and press
[ENTER].
The menu to enter GCN is displayed.
5. Use the numbered buttons (1~9) to enter the
GCN and press [ENTER] when done.
Press [ꢂ] [ꢃ] to go back to advance/return to the previous/
next digit.
6. To set GCN for other channels, repeat step 3~5.
7. When complete, press [ꢀ] / [ꢁ] to go to “Exit”
and press [ENTER] to exit the channel editor
menu.
PDC
“PDC” (program delivery control) are used to control
the start and duration of TV channel recordings. If a TV
program starts earlier or ends later than was
scheduled, the DVD recorder will then turn on and off
at the correct time. Refer to “Timer Record using the
VIDEO Plus+ system” section for details about setting.
Notes:
1. You must enter the start time exactly to the minute. If you
want to program a time that is different from the PDC time,
you must switch off PDC.
2. Only on TV program of a TV channel can be controlled
using “PDC” at a time. If you want to record two or more
TV programs on a TV channel using “PDC,” you need to
program these as two separate recordings.
3. Since the DVD recorder requires a certain lead time for
getting the disc up to speed and positioning the laser before
recording can start, it is possible that the recorder will miss
the first few seconds of a TV show recorded with PDC. In
this case, disable PDC and enter a start time one minute
earlier.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY GUIDER
Easy Guider menu is an unique user interface to
guide you through basic functions of this
recorder. By using the Easy Guider menu, it is
less time-consuming to operate this system.
Users no longer need to go through normal
operations that may require far more steps and
different interfaces.
Playback music files
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Playback” and then
press [ENTER].
3. Press [ꢀ] [ꢁ] to select DVD or HDD and then
press [ENTER].
Playback video files
4. Press [ꢀ] [ꢁ] to select “Music” and press
[ENTER].
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Playback” and then
press [ENTER].
5. The selected file screen appears. Press [ꢀ] [ꢁ]
[ꢂ] [ꢃ] to select a music file to start playback
with and press [ENTER].
3. Press [ꢀ] [ꢁ] to select DVD or HDD and then
press [ENTER].
If you want to go to the next page or to the return previous
page, you can select the [
number icon.
] [
] icon or the page
6. Press [ꢀPAUSE/STEP] to pause playback.
Press [ PLAY] to resume normal playback.
Press [ STOP] to stop playback at a marked stop.
Press [
STOP] twice to bring the playback to a full stop.
Playback picture files
4. Press [ꢀ] [ꢁ] to select “Video” and press
[ENTER].
1. Press [ GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Playback” and then
press [ENTER].
3. Press [ꢀ] [ꢁ] to select DVD or HDD and then
press [ENTER].
4. Press [ꢀ] [ꢁ] to select “Pictures” and press
[ENTER].
5. The selected file screen appears. Press [ꢀ] [ꢁ]
[ꢂ] [ꢃ] to select a video file to start playback
with and press [ENTER].
If you want to go to the next page or return to the previous
page, you can select the [
number icon.
] [
] icon or the page
5. The selected file screen appears. Press [ꢀ] [ꢁ]
[ꢂ] [ꢃ] to select a picture file to start playback
with and press [ENTER].
If you want to go to the next page or return to the previous
page, you can select the [
number icon.
] [
] icon or the page
6. Press [ꢀ PAUSE/STEP] to pause playback.
Press [ PLAY] to resume normal playback.
Press [ STOP] to stop playback at a marked stop.
6. Press [ꢀPAUSE/STEP] to pause playback.
Press [ PLAY] to resume normal playback.
Press [ STOP] to stop playback.
Press [
STOP] twice to bring the playback to a full stop.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY GUIDER
Record on the HDD
Playback pictures with music
1. Press [GUIDER] to display the Easy Guider
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Playback” and then
press [ENTER].
menu.
2. Press [ꢀ] [ꢁ] to select “Record” and then
press [ENTER].
3. Press [ꢀ] [ꢁ] to select DVD or HDD and then
press [ENTER].
4. Press [ꢀ] [ꢁ] to select “Pictures With Music”
and press [ENTER].
3. Press [ꢀ] [ꢁ] to select the Signal- Input ( TV,
AV1-front, AV2-rear, DV-in) and press [ENTER].
If you select “TV,” press [ꢀ] [ꢁ] to select the channel you want
to record and press [ENTER]. Press [ꢀ] [ꢁ] and [ENTER] to set
the PDC mode off.
5. Theselectedfilescreenappears.Press[ꢀ] [ꢁ]
[ꢂ] [ꢃ] to select a picture file to start playback
with and press [ENTER].
4. Press [ꢀ] [ꢁ] to select “HDD” and press
6. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to select a music file to
start playback with and press [ENTER].
Playback will start.
[ENTER].
7. Press [ꢀ]/[ꢁ] to select “Rotate RIGHT” or “Rotate
LEFT” and “Rotate UP” “Rotate down.”
Press [ꢂ] or [ꢃ] to skip the picture.
Press [
MP3 file.
NEXT ] or [
PREV ] to skip the
5. Press [ꢀ] [ꢁ] to select “Recording mode” and
8. Press [ꢀPAUSE/STEP] to pause playback.
Press [ PLAY] to resume normal playback.
Press [ STOP] to stop playback.
then press [ENTER].
Playback the last recorded title (on HDD only)
1. Press [GUIDER] to display the Easy Guider
menu.
If you select “TV” in step 3, press [ꢀ] [ꢁ] to select the desired
2. Press [ꢀ] [ꢁ] to select “Playback” and then
press [ENTER].
TV sound and press [ENTER].
3. Press [ꢀ] [ꢁ] to select HDD and press [ENTER].
4. Press [ꢀ] [ꢁ] to select “Last Record” and press
[ENTER].
Playback of the title last recorded on your HDD will begin.
6. Press [ENTER] to start recording.
Press [ STOP] to stop recording.
Press [ꢀPAUSE/STEP] to pause recording.
Notes:
1. You can press [GUIDER] to exit the Easy Guider menu.
2. Bilingual TV program which input through AV input terminal
is recorded on DVD disc (HDD) as stereo TV program.
When this title is playbacked, the both Main and Sub sound
can be heard from the speakers.
5. Press [ꢀ PAUSE/STEP] to pause playback.
Press [ PLAY] to resume normal playback.
Press [ STOP] to stop playback at a marked stop.
Please choose the desired sound which you want to enjoy
on the TV side.
3. Stereo broadcasting is recorded by stereo and monaural
one is recorded by mono.
Press [
STOP] twice to bring the playback to a full stop.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY GUIDER
Record on DVD
Timer Record (Date/Time Setting)
1. Press [GUIDER] to display the Easy Guider
menu.
Make sure a recordable disc is inserted before recording.
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Timer Record” and
then press [ENTER].
2. Press [ꢀ] [ꢁ] to select “Record” and then
press [ENTER].
3. Press [ꢀ] [ꢁ] to select “Date/Time Setting” and
3. Press [ꢀ] [ꢁ] to select the Signal-Input (TV,
AV1-front, AV2-rear, DV-in) and press [ENTER].
If you select “TV,” press [ꢀ] [ꢁ] to select the channel you want to
record and press [ENTER].
press [ENTER].
4. Press [ꢀ] [ꢁ] to select “DVD” and press
[ENTER].
5. Press [ꢀ] [ꢁ] to select a disc format and press
[ENTER].
4. Press [ꢀ] [ꢁ] to select the Signal-Input ( TV,
AV1-front, AV2-rear, DV-in ) and press [ENTER].
If you select “TV,” press [ꢀ] [ꢁ] to select the channel you want to
record and press [ENTER]. Press [ꢀ] [ꢁ] and [ENTER] to set the
PDC mode on or off.
If you select “TV” in step 3, press [ꢀ] [ꢁ] to select the desired
TV sound and press [ENTER].
If you select “AV1-front or AV2-rear,” press [ꢀ] [ꢁ] to set PDC
mode on or off.
“Go !” is selected.
6. Press [ENTER] to start recording.
Press [ STOP] to stop recording.
Press [ꢀPAUSE/STEP] to pause recording.
5. Press [ꢀ][ꢁ] to select “Once,” “Daily,” or “Weekly.”
Notes:
1. If a new recordable CD-R or a newly erased CD-RW is
used for recording, press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select a
disc format the disc is to be prepared as and press
[ENTER] : SVCD, VCD, Audio CD or Data CD.
2. Stereo broadcasting is recorded by stereo and monaural
one is recorded by mono.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY GUIDER
6. Press [ꢀ][ꢁ] [ꢂ] [ꢃ] or the numbered buttons
Note:
(0~9) to set the date and press [ENTER] when done.
For Timer Record, there are six recording modes avaialbe: HQ,
SP, LP, EP, SLP and Just Fit. When the recording mode is set
to be “Just Fit,” the recording mode will be automatically
adjusted depending on how much recording space is available
on the disc/HDD.
13. Press [ STANDBY/ON] to turn the recorder
off to activate Timer Record function.
Note:
7. Press [ꢀ][ꢁ] [ꢂ] [ꢃ] or the numbered buttons
(0~9) to set the time and press [ENTER] when
done.
When you first play a recordable CD-R disc or an empty CD-RW
disc on the disc tray, select a disc format the disc is to be
prepared as: SVCD, VCD, Audio CD or Data CD. The format
selected determines the recording quality.
8. Press [ꢀ][ꢁ] to set “Length” and then press [ENTER] .
®
Timer Record (VIDEO Plus+ Setting)
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Timer Record” and
then press [ENTER].
3. Press [ꢀ] [ꢁ] to select “VIDEO Plus+” and press
[ENTER].
9. Press [ꢀ][ꢁ] to select “HDD” or “DVD” and then
press [ENTER] .
10. Press [ꢀ][ꢁ] to select a disc format and press
[ENTER]. (For DVD disc only)
11. Press [ꢀ] [ꢁ] to select a recording mode and
press [ENTER].
4. Press [ꢀ] [ꢁ] to select once, daily or weekly
and press [ENTER].
12. Press [ꢀ] [ꢁ] to select the desired TV sound and
press [ENTER].
5. Use the numbered buttons to enter the PlusCode
number and then press [ENTER] . Press [ꢀ][ꢁ] to
set the PDC mode on or off and press [ENTER].
13. The “Timer Record information” will appear and
press [ENTER] to exit the timer record settings.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY GUIDER
6. After entering the PlusCode number, the “GCN”
and “Present Channel” will be displayed.
Press [ENTER] to preset the channel.
3. Press [ꢀ] [ꢁ] to select “HDD to DVD” and
press [ENTER].
The disc preparation process will take place in the background.
This process only takes a few moments.
7. Press [ꢀ][ꢁ] to select “DVD” or “HDD” and then
press [ENTER] .
8. Press [ꢀ] [ꢁ] to select a disc format and then
press [ENTER].
If a CD-R or CD-RW is used for recording, you need to select
SVCD, VCD or Audio CD. If a DVD disc is used for recording,
you need to select “DVD VR” format.
9. Press [ꢀ] [ꢁ] to select “Recording mode” and
then press [ENTER].
4. Press [ꢀ] [ꢁ] to select the type of the file: Video,
Pictures or Music and press [ENTER].
For CD-R/RW, the format selected determines the recording
quality.
5. The selected file screen appears. Press [ꢀ] [ꢁ]
[ꢂ] [ꢃ] to select the file to copy and press
[ENTER].
10.Press [ꢀ] [ꢁ] to select TV audio and press
[ENTER].
6. When complete, go to “Exit” and press [ENTER].
11.The “Timer Record information” will be displayed.
Press [ENTER] to exit the timer record settings for
®
Copy (From DVD to HDD )
VIDEO Plus+ .
Press [
OPEN/CLOSE] to open the disc tray and insert a
disc with recorded contents on it. Press the button again to
close the tray.
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [ꢀ] [ꢁ] to select “Copy” and press
[ENTER].
3. Press [ꢀ] [ꢁ] to select “DVD to HDD” and
12. Press [ STANDBY/ON] to turn the recorder off
to activate Timer Record function.
Note:
press [ENTER].
When you first play a recordable CD-R disc or an empty CD-RW
disc on the disc tray, select a disc format the disc is to be
prepared as: SVCD, VCD, Audio CD or Data CD. The format
selected determines the recording quality.
Copy (From HDD to DVD)
Press [
OPEN/CLOSE] to open the disc tray and insert a
4. Press [ꢀ] [ꢁ] to select the type of the file: Video,
recordable DVD disc. Press the button again to close the tray.
1. Press [GUIDER] to display the Easy Guider
menu.
Music, Pictures or All and press [ENTER].
5. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to select the file to copy and
press [ENTER].
2. Press [ꢀ] [ꢁ] to select “Copy” and press
[ENTER].
6. When complete, go to “Exit” and press [ENTER].
Note:
Notes:
You can only copy picture files (in JPEG or BMP formats), audio
files (in MP3 or WAV format) and recorded video titles.
Reference the “Copy” section for the right disc to use.
1. You can only copy picture files (in JPEG or BMP formats),
audio files (in MP3 or WAV format). Sanyo has no right to
grant such permission. Permission should always be
sought from the copyright owner.
2. The title of DVD-Video cannot be copied from DVD to
HDD.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Note:
Before recording
You can also use the numbered buttons to select a channel.
Cautions:
5.Press [ꢁREC ] to start recording.
When recording is completed it may take a few
moments for the session to close.
1. This DVD recorder records on DVD+R/+RW,CD-R/RW
discs and the built-in HDD. Please use recommended
recordable discs to ensure the best recording quality.
2. DVD+R and CD-R are write-once discs.
3. DVD+RW and CD-RW are a re-writable discs.
4. You cannot add new recording sessions to DVD+R discs
after the discs are finalized.
5. In some cases, you may not be able to add new recording
(s) to a recordable DVD disc that contains contents written
on other DVD recorders.
6. A disc records 49 video titles maximum. A title recorded
on a DVD disc contains 99 chapter marks maximum. And a
disc contains 254 chapter marks totally maximum.
Recording continues until you stop the recording or when the
disc or the HDD is full.
To stop recording
When you press [
STOP] , it may take a few moments for
7. A title recorded on the built-in HDD contains 999 chapter
marks maximum.
recording to stop and the session to close.
Recording television programs
1.Press [ STANDBY/ON] to turn the unit on.
2.Press [HDD/DVD] to set the target device as “HDD”
or “DVD.”
To pause recording
Press [ꢀPAUSE/STEP] to pause recording, and press [ꢀ
PAUSE/STEP] again to resume recording.
If “DVD” is selected as the target device, press [
OPEN/
CLOSE] to open the disc tray and insert a recordable disc.
Press the button again to close the tray.
When you insert a new recordable DVD disc, the DVD recorder
automatically starts the disc preparation process.
When you insert a new recordable CD-R or CD-RW disc, press
[ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the disc format the disc is to be
prepared as.
To change the recording mode before recording:
Press [SETUP] button.
3.Press [REC MODE] continuously to select the
desired recording quality.
To change the TV Audio setting before recording:
HQꢄSPꢄLPꢄEPꢄSLP
Press [SETUP] button.
Press [SOURCE] and press [ꢀ] [ꢁ] to select “TV”
as the signal-input source.
4.Press [ CH + or - ] or press [ꢀ] [ꢁ] to select the
TV channel you want to record.
Note:
The new setting can't change the current recording mode but
will be activated during the next recording session.
To check the disc status while recording
Press [DISPLAY] , the recording information appears.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Adding new recordings
Playback the last recorded title (on HDD only)
Adding new recordings after other recording
sessions.
Press [ꢃPLAY] or [GUIDER] to start the playback
of the last recorded title .
Press [ꢁREC ] to start recording, and press
This function is only available when the desired title resides on
the HDD.
[
STOP] at the point you want to stop.
Using [ꢃPLAY]
1. Press [ꢃPLAY] and the last recorded title will
start playback.
Using[GUIDER]
1. Press [GUIDER] and select the “Playback” icon.
2. Confirm that the playback device is HDD.
Note:
Each new recording session is placed after the previous session
unless a certain recording title is set to be overwritten.
(Reference the “Overwrite” function in the “Editing” section for
additional details.)
3. Press [ꢀ] [ꢁ] to go to the “Last Record” icon
and press [ENTER]. The playback will start.
Change Chapter Intervals
Creating chapters while recording
The DVD recorder can automatically divide a session into
chapters by inserting chapter marks at 5/10/15/20/25/30-minute
interval during the recording process.
1. Press [SETUP] to display the setup menu.
2. Press [ꢀ] [ꢁ] to select “Record” and press
[ꢃ].
3. Press [ꢀ] [ꢁ] to select “Chapter Mark” to set
up the interval time.
Notes:
1. If a power failure occurs, the program you are recording
may be lost.
2. Before you start, please check that the recordable disc or
hard disk has enough available space for the recording.
3. You can not change the recording mode during recording.
4. Before playing a DVD+R, CD-R, CD-RW disc on another
player, you first need to finalize the disc.
4. Press [SETUP] to exit the setup menu.
Notes:
1. During recording, press [EDIT] to add chapter mark(s) in the
recorded session manually.
2. You can also start recording using the “Easy Guider”
Menu. Press [GUIDER], select “Record” and press [ENTER].
Follow the steps to set the recording mode.
3. Before you start, please ensure that the recordable disc or
hard disk has enough available space for the recording
session.
4. You cannot change the channel or recording mode during
recording.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
To start recording
Recording from a VCR or Camcorder
1. Press [HDD/DVD] to set the target device for the
recording.
Before starting to record
This DVD recorder can accept standard CVBS (RCA) analog
audio/video cable or IEEE-1394 cable and record Camcorder
onto DVD in the digital video format of your choice. The unit
functions much like a digital VCR. Examples of use include
archiving videotapes or transferring from a Video Cassette
Recorder or Camcorder to a recordable DVD disc or hard disk
drive. This DVD recorder allows basic DV control with the DVD
Recorder’s remote control when connected via the DV Link.
If “DVD” is set as the target device, press [
OPEN/CLOSE]
to open the disc tray and insert a recordable DVD disc with
the label side facing up.
If a new recordable CD-R or CD-RW is used for recording, press
[ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the disc format and press [ENTER]
.
The front panel and rear panel connection
Connect a Video Cassette Recorder or Camcorder to the unit’s
input terminals.
2. Press [SOURCE] to select the signal-input (TV,
AV1-front, AV2-rear, DV-in).
3. Start to play on the VCR or Camcorder.
4. Press [ꢁREC ] on the DVD recorder to capture
your video/audio signal from the VCR or
Camcorder onto a recordable DVD disc or hard
disk.
5.Press [ STOP] to stop recording.
To pause recording
Press [ꢀPAUSE/STEP] to pause recording. If you want to
restart recording, press [ꢀPAUSE/STEP] to resume
recording.
Note:
When connected to VCR or other external devices, there will
be no outputting S-Video signal from the DVD recorder, if the
DVD recorder is switched off.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
One-touch recording
Use “One-touch recording” to start recording immediately in 30-
minute blocks. Press [ REC ] twice to start a 30-minute
ꢁ
recording session. Press [ REC ] repeatedly to record longer
ꢁ
timed recordings, up to 6 hours in thirty-minute increments.
Pressing [ REC ] when the timed recording exceeds the 6-
ꢁ
hour constraint automatically sets “one-touch recording” off.
For recording on DVD discs, the length of recording depends
on the current recording mode/speed and the amount of time
available on the disc. For recording on the built-in HDD, the
length of recording is 6 hours maximum.
7. Press [ꢀ] [ꢁ] to select “DV” Input, and press
[ENTER] to confirm.
DV recording
Before you start to record DV contents
This DVD recorder allows basic DV control functions with the
remote control. The DVD recorder is equipped with a camcorder
control (Play, Stop, FF or REV) feature via the DV Link
connection. Simply move the screen cursor to the desired
function on the DV input screen and press [ENTER] on the
remote control.
8. Press [ꢀ] [ꢁ] to select a recording mode and
Use “Easy Guider” Menu to record DV signal
press [ENTER]. (For DVD disc or HDD only)
If you are to record DV signals on a disc, press [ OPEN/
CLOSE] to open the disc tray and insert a recordable disc.
If a new recordable CD-R or CD-RW is used for recording, press
[ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the disc format the disc is to be
prepared as and press [ENTER] .
9. “Go!” is selected. Press [ENTER] to start
recording.
Note:
1. Power on your TV and this DVD recorder.
This DVD-Recorder will stay in “Pause” mode when no DV
input signal is detected.
2. Connect the DV cable (IEEE-1394 4-pin to 4-pin
cable) to both the DV Camcorder and the DVD-
Recorder.
10.To pause recording.
Press [ꢀPAUSE/STEP ] on the remote control to pause
recording. Press [ꢀPAUSE/STEP ] again, if you want to
resume recording.
11.To stop recording.
Press [
STOP]
Note:
Before playing a DVD+R disc on another player, you will first
need to finalize the disc. Reference the “finalize” function in
the “Disc Tools” section for additional information.
3. Power on the DV Camcorder. Start “Playback
mode” on the DV Camcorder.
4. “Pause” the DV Camcorder at where you want to
record.
5. Press [GUIDER] on the remote control.
This activates the Easy Guider menu.
6. Press [ꢀ] [ꢁ] to select the “Record” icon, and
press [ENTER] to start recording.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
DV control
DV Recording -- One-Touch Recording
Before you start to record DV contents
After recording is stopped, a DV control bar will appear on the
screen. This allows basic DV control utilizing this DVD
recorder’s remote control.
This unit allows basic DV control on screen. The on screen
functions are accessed using the DVD recorder remote control.
1. Power on your TV and this DVD recorder.
2. Press [HDD/DVD] to set the target device for the
recording.
If “DVD” is set as the target device, press [
OPEN/CLOSE]
to open the disc tray and insert a recordable disc with the
label side facing up.
If a new recordable CD-R or CD-RW is used for recording, press
[ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the disc format. The disc is to be
prepared as and press [ENTER] .
1. Press [ꢂ] [ꢃ] to select “ ” and press [ENTER] to
start the DV Camcorder playing.
2. Press [ꢂ] [ꢃ] to select “
” and press [ENTER]
during playback mode to forward search the DV
Camcorder.
3. Press [ꢂ] [ꢃ] to select “
” and press [ENTER]
3. Connect the DV Cable (IEEE-1394 4-pin to 4-pin
cable) to both the DV Camcorder and this DVD
recorder.
during playback mode to backward search the DV
Camcorder.
4. Press [ꢂ] [ꢃ] to select “ ” and press [ENTER]
during playback mode to stop the DV Camcorder
playing.
4. Power on the DV Camcorder. Set “Playback
mode” on the DV Camcorder.
5. “Pause” the DV Camcorder at where you want to
record.
5. Press [ꢂ] [ꢃ] to select “ ” and press [ENTER]
during playback mode to pause the DV Camcorder
playing.
6. Press [SOURCE] to change the “Signal-Input
source” and select the “DV-in” input.
Notes:
1. The DV-Link input jack on this unit is for use with DV
compatible camcorders only.
2. Only DV signals can be input to the DV-Link jack on this
DVD recorder.
3. Do not connect a MICRO MV format video camcorder to
this DV-Link (IEEE-1394) jack.
7. Resume DV Camcorder playback and press
[ꢁREC ] on the DVD Recorder to start
recording.
8. To pause recording.
Press [ꢀPAUSE/STEP ] on the remote control to pause
recording. Press [ꢀPAUSE/STEP ] again, if you want to
resume recording.
9. To stop recording.
Press [
STOP ] to stop recording.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Record on a CD-R/CD-RW disc
Notes:
1.You can’t perform any record before the CD-R/CD-RW disc is
prepared.
Before starting to record
The DVD recorder can also record video in either VCD/
SVCD or Audio CD format on CD-R/RW discs. Before you
start to record, please use qualified recordable disc to
ensure the best recording quality.
2.Only single format is allowed on a single disc.
3.You can’t change the format of CD-R disc after preparing it.
4.To change the format of the CD-RW disc, you must use the
“Erase” function at the “DISC TOOLS” menu.
5.All contents in the disc will be deleted after erasing it.O
6.You must finalize the disc before you can playback the disc on
other DVD / VCD / SVCD player or DVD-ROM on PC.
Note:
Ensure to prepare the disc in the desired disc format before you
started to record.
6. “Go!” is selected. Press [ENTER] to record your
signal onto the disc.
Creating a correct disc format
1. Press [ OPEN/CLOSE] to open the disc tray and
insert a recordable CD-R or CD-RW disc with the
label side facing up.
2. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the disc format. The
disc is to be prepared as and press [ENTER].
3. The disc preparation process will start. When done,
the disc is ready to be used for recording.
Create the disc format using the Disc Tools menu
1. Press [ TOOLS] to display the “DISC TOOLS” menu,
press [ꢀ] [ꢁ] to select the “Erase” icon and then
press [ENTER].
7. Press [ STOP] to stop recording.
To pause recording
Press [ꢀPAUSE/STEP] to pause recording , and if you want to
restart recording, press [ꢀPAUSE/STEP] again or [ REC].
ꢁ
Audio CD recording
1. Place a well-prepared CD-R / CD-RW disc onto the
tray with the disc’s label face up.
Recording mode (on an empty 700MB disc)
Recording Mode Recording Time (on empty 700MB disc)
2. Press [ GUIDER ] to display the Easy Guider menu,
press [ꢀ] [ꢁ] to select “Record” and then press
[ENTER].
VCD
SVCD
68 minutes
34 minutes
70 minutes
3. Press [ꢀ] [ꢁ] to select the audio signal input (TV,
AV1-front, AV2-rear, DV-in) and press [ENTER].
Audio CD
2. Press [ꢀ] [ꢁ] to select the desired recording
4. Press [ꢀ] [ꢁ] to select “Audio CD” as the desired
format. “Go!” is selected and then press [ENTER].
recording format and then press [ENTER].
3. When the disc is well-prepared, select the “Exit”
icon and press [ENTER] to exit the erase menu.
5. Press [ꢀ] [ꢁ] to select the desired TV Sound and
then press [ENTER].
VCD/SVCD recording
1. Place a prepared CD-R or CD-RW disc onto the tray
with the disc’s label facing up.
6. “Go!” is selected. Press [ENTER] to record your audio
signal into a recordable CD disc.
2. Press [GUIDER ] to display the Easy Guider menu,
press [ꢀ] [ꢁ] to select “Record” and then press
[ENTER].
7. Press [EDIT] to create an new audio track into disc
during recording.
8. Press [ STOP] to stop audio recording.
3. Press [ꢀ] [ꢁ] to select the signal-input ( TV, AV1-
Notes:
front, AV2-rear, DV-in ) and press [ENTER].
1.Single press of [EDIT] key will automatically create an new
audio track by 2 sec interval.
2.Audio source input during these 2 sec will be recorded onto
the beginning of the next track.
3.You must finalize the disc before you can playback the disc on
other Audio CD / DVD / VCD / SVCD player or CD / DVD-ROM on
a PC.
4. Press [ꢀ] [ꢁ] to select VCD or SVCD as the desired
recording format and then press [ENTER].
5. Press [ꢀ] [ꢁ] to select the desired TV Sound and
then press [ENTER].
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORD
8. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Repeat
(Once, Daily or Weekly),” and then press [ENTER]
to bring up the list.
Prior to timer record
Please ensure that the recordable disc or the HDD has enough
available space for the Timer Record function. Before you start
to record, follow the steps to set the date, time, picture quality
and channel of the program or input source manually. You can
set up 16 individual sessions in the Timer Recording function.
If you select “Once,” you need to set the date. Move the cursor
to highlight “date” and press [ENTER]. Use the numbered
buttons (0~9) or [ꢀ] [ꢁ] [ꢂ] [ꢃ] to enter the date.
Setting the timer
1. Press [ STANDBY/ON ] to turn the unit on.
2. Press [TIMER] to display the “TIMER RECORD”
menu.
If you select “Daily,” you do not need to set the date since the
Timer Record is set for each day until the timer recording item is
cancelled or the media is full.
3. Press [ꢀ][ꢁ] to select an item from the timer
setting list and press [ENTER] to activate the
system setup menu for the Timer Record function.
If you select “Weekly,” a weekly calender will display on-
screen for you to select the day. Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] to
move the cursor to highlight the desired day and press
[ENTER] to make your selection. When completed, move the
cursor to “OK” and press [ENTER] to save the desired setting.
4. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Source
(Signal Source),” and then press [ENTER] to
bring up the list.
Press [ꢀ] [ꢁ] and [ENTER] to make your selection.
5. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Channel (TV
Channel),” and then press [ENTER] to bring up
the list. This step only applies when the “TV” is
selected as the source.
Note:
If the mode is set as “Daily” or “Weekly,” press [ꢂ] [ꢃ] [ꢀ]
[ꢁ] to move the highlighted cursor to the “Advanced” icon
and press [ENTER]. You can choose to apply the setting
“Without Restriction” or “With Restriction.” When “With
Restriction” is selected, enter the “Start” date and “End” date
to set the period of time for a valid setting. Move the high-
lighted cursor to “OK” and press [ENTER] to confirm the
setting or to “Cancel” and press [ENTER] for resetting.
Press [ꢀ] [ꢁ] and [ENTER] to make your selection.
6. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “HDD/DVD,”
and then press [ENTER] to bring up the list.
Press [ꢀ] [ꢁ] and [ENTER] to make your selection.
7. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Mode
(Recording Quality),” and then press [ENTER] to
bring up the list.
Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] and [ENTER] to make your selection.
Recording quality for timer recording on DVD discs and
HDD:
HQ <-> EP <->LP<->SP <-> SLP <-> Just Fit
Recording quality for timer recording on CD discs:
Audio CD <-> VCD <-> SVCD
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORD
9. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Start (Start
Time),” and then press [ENTER] .
Use the numbered buttons (0~9) or press [ꢀ] [ꢁ] [ꢂ] [ꢃ] to
enter the start time.
To stop recording during Timer Record
When you press [
the record to stop.
STOP ] , it may take a few seconds for
To check the recording status while Timer Record is
active
Press [DISPLAY] and the Timer Record information appears on-
screen.
Notes:
1. When the Timer Record function is active, the “TIMER
LED” on the DVD Recorder front panel will illuminate.
2. The DVD recorder must be turned off to activate the Timer
Record function.
3. Make sure that a recordable DVD disc or a well-prepared
CD-R/RW disc is placed before the scheduled time,
corresponding to the selected recording quality.
10. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “End (End Time),”
and then press [ENTER].
Use the numbered buttons (0~9) or press [ꢀ] [ꢁ] [ꢂ] [ꢃ] to
enter the end time.
®
Timer Record using the VIDEO Plus+ system
1. Press [ STANDBY/ON] to turn the unit on.
2. Press [TIMER] to display the “TIMER RECORD”
menu.
If you enter a wrong selection
Press [ꢂ] [ꢃ] to re-select the item you want to change.
11. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Sound (TV
Sound BIL)” and then press [ENTER] to bring up
thelist.
12. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select the “PDC” and
then press [ENTER] to set it on or off.
Press [ꢀ] [ꢁ] and [ENTER] to make your selection.
3. Press [ꢀ][ꢁ] to select an item from the timer
setting list and press [ENTER] to activate the
setup menu for the Timer Record function.
13. Press [ꢀ][ꢁ] to select “OK” and press [ENTER]
to save the setting for the timer record item and
go back to the Timer Record list.
Press [ꢂ] to [Reset] if you want to reset the timer record
item.
14. Press [ꢀ] [ꢁ] to go to another item on the list
and press [ENTER] if you want to set up for more
Timer Record programs.
If not, move to the “Exit” icon and press [ENTER] or press
[TIMER] to exit the Timer Record List.
4. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “VIDEO Plus+” and
then press [ENTER] to bring up setup menu.
Or press [VIDEO Plus+] to bring up the VIDEO Plus+ menu.
5. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Repeat (Once,
Daily or Weekly),” and then press [ENTER] to bring
up the list.
Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] and [ENTER] to make your selection.
15. Press [ STANDBY/ON] to turn off the unit and
activate the “Timer Record” function.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMER RECORD
6. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “PlusCode#
(PlusCode number),” and then press [ENTER] to
enter the number.
Use the numbered buttons (0~9) or [ꢀ] [ꢁ] [ꢂ] [ꢃ] to enter
the PlusCode number.
Note:
If the Preset Channel of this GCN is not set, the following
screen will appear. Use the numbered buttons (0~9) or [ꢀ]
[ꢁ] [ꢂ] [ꢃ] to enter the Preset Channel and press [ENTER] to
comfirm.
13. Press [ STANDBY/ON] to turn off the unit and
activate the “Timer Record” function.
Notes:
1. When the Timer Record function is active, the “TIMER
LED” on the DVD Recorder front panel will illuminate.
2. The DVD recorder must be turned off to activate the Timer
Record function.
3. Make sure that a recordable DVD disc or a well-prepared
CD-R/RW disc is placed before the scheduled time,
corresponding to the selected recording quality.
4. When “Once” timer recording is set, it cannot be changed
to “Weekly” timer recording. Select “Weekly” first in case
of “Weekly” timer recording.
7. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “HDD/DVD,” and
then press [ENTER] to bring up the list.
Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] and [ENTER] to make your selection.
If “DVD” is set as the target device, press [ OPEN/CLOSE] to
open the disc tray and insert a recordable DVD disc.
8. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Mode
(Recording Quality),” and then press [ENTER] to
bring up the list.
Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] and [ENTER] to make your selection.
Press [ꢂ] [ꢃ] to re-select the item you want to change.
Recording quality for timer recording on DVD discs and the
HDD:
HQ <-> EP <->LP<->SP <-> SLP <-> Just Fit
Recording quality for timer recording on CD discs:
Audio CD <-> VCD <-> SVCD
9. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “Sound (TV
Sound BIL)” and then press [ENTER] to bring up
the list.
10. Press [ꢂ] [ꢃ] [ꢀ][ꢁ] to select “PDC”and then
press [ENTER] to set it on or off.
Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] and [ENTER] to make your selection.
11. Press [ꢀ][ꢁ] to select “OK”and [ENTER] to save
the setting or the timer record item and go back
to the Timer Record list.
Press [ꢂ] to [Reset] if you want to reset the timer record
item.
12. Press [ꢀ] [ꢁ] to go to another item on the list
and press [ENTER] if you want to set up for more
Timer Record programs.
If not, move to the “Exit” icon and press [ENTER] to exit the
Timer Record List.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME SHIFT
The “Time Shift” feature allows you to “Pause Live TV” and
resume viewing at the point of interruption, at your leisure.
Record and Play
Note: “Pause Live TV” is constrained within 3 hours.
Follow the steps below to start playback of the recorded program/
Timer Record program before the recording is scheduled to end.
Pausing Live TV Broadcast
1. During recording/Timer Record on the HDD, press
[ꢃPLAY].
Playback will start from the beginning of the recorded program.
1.Press [ STANDY/ON] to turn the unit on.
2. Switch on your TV and set the video input to this
recorder.
3.Press [ CH + or -] buttons on the recorder’s remote
control to select the desired channel.
Since the TV’s video input is set to be the recorder, channel
selection HAS to be made with the recorder’s remote control.
To turn the audio volume up and down, use the TV’s remote
control.
2. Press [
FF] or [
REV ] to perform fast-
forward or fast rewind scanning.
Press [ꢀPAUSE/STEP ] to pause playback. Press
[ꢀPAUSE/STEP ] again if you want to resume
viewing.
4. When you choose to leave your TV and must
stop watching, press [TIME SHIFT].
When [TIME SHIFT] is pressed the video broadcast on TV is set in
pause mode. The scene displayed on the TV is the last picture
shown when you press [TIME SHIFT].
Press [
STOP] to stop playback/viewing.
5. When you are back in front of the TV and ready to
resume viewing, press [ꢃPLAY] and the
TV program will begin playing starting from the
interrupted scene.
Note:
If you press [ STOP] again, the recording function will be
turned off.
6.Press [ FF] or [
REV] to perform fast-
3. If you want to stop recording, press [ STOP] for a
second time.
forward or fast rewind scanning (to the point where
[TIME SHIFT] begins).
Press [ꢀPAUSE/STEP ] to pause viewing. Press
[ꢀPAUSE/STEP] again if you want to resume
viewing.
7. Press [TIME SHIFT] to turn the time shift function off
and switch to viewing live TV broadcast.
Note:
Record and Play only functions when the contents are to be
recorded on the HDD.
Note:
Note:
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
DVD/VCD/SVCD video disc playback
Before you begin to enjoy the digital world of audio and video on DVDs, please ensure that you have made the correct settings in the
Setup menus. These settings should correspond to the capabilities of your home system. Having made the correct settings, you are
now ready to use the DVD recorder to enjoy DVDs, Video CDs, and CDs.
Basic playback
Press [ STOP] to stop playback.
Turn on the television and select the appropriate video input
on the television to suit the connections for the player.
At a marked stop, press [ PLAY] to resume playback.
Press [
STOP] twice to bring the playback to a full stop.
Press [ PLAY] to start playback from the beginning of the
disc.
Press [ STANDBY/ON] to turn on the unit.
Press to turn the unit on or off.
Press [ DISPLAY ] to display disc status
during playback.
Press [ OPEN/CLOSE ] to open the disc
tray. Place the disc in the tray, label-side up.
Press [ DISC MENU ] to display the thumbnail
icons menu on the TV screen.
Press [ PLAY ] to start playback.
Press [
FF ] to perform fast forward
Press to return to the DVD’s title or disc root menu for the
current title during playback.
scanning.
Press repeatedly to play the disc forward at 2x, 4x, 8x,or
16x speeds.
VCD
SVCD
Press [0 ,1~9 ] the numbered buttons to select an item of the
title menu.
Press [
scanning.
REV ] to perform fast reverse
DVD
Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] to select an item and press
[ENTER].
Press repeatedly to play the disc reverse at 1x, 2x, 4x, 8x,
or 16x speeds.
Press [
NEXT] to advance to the next
chapter/track.
Press repeatedly to skip to the next chapter during playback.
Press [
PREV] to reverse to the previous
chapter.
Press repeatedly to return to the beginning of previous
chapters during playback.
Press [ꢀPAUSE/STEP] to pause playback.
Press [ꢀPAUSE/STEP] again to start “frame
by frame mode.”
Press repeatedly to advance DVDs and Video CDs frame by
frame during playback in pause mode.
Press [ PLAY] to restart normal playback.
Sample Thumbnail display
Press [BROWSER] to browse the contents
of a DVD disc or the HDD.
Press [ PLAY LIST MENU ] to display the title
menu on the TV screen.
Press [ꢀ] [ꢁ] [ꢂ] [ꢃ] to select an item and press [ENTER].
Press [HDD/DVD] to select HDD or DVD to
playback the contents saved.
Note:
The [PLAY LIST MENU] button only functions while the unit is
in playback mode. Depressing this button during other
operations won’t work on this unit.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Note:
Navigation operation
Moving the cursor left through each menu takes you to the
previous level. Moving the cursor left at the first menu
selection closes the dialog box.
During playback, press [NAVI] to display the “Navigation”
menu.
A-B
Repeating a desired part.
Select “Set Point A” at the beginning of the part
you want to repeat.
Repeat
Select “Set Point B” at the end of the part you
want to repeat.
The unit locates “A” and starts repeat playback
between “A” and “B.”
Select [Cancel]. The A-B repeat mode turns
off, then normal playback continues.
During playback to select a subtitle language
from those available on the current disc. Press
[SUBTITLE] repeatedly during playback to see
the different subtitle languages.
Subtitle
Repeat
Repeat playback. Move the highlighted cursor
to “Repeat” and press [ENTER] repeatedly to
choose a repeat option. Depending on the type of
Disc, you may choose to play the Track, Title,
file or Disc repeatedly.
Note:
For DVD, the repeat options are:
1 TRACK <-> Repeat Off
For VCD and SVCD, the repeat options are:
ALL TRACK <-> Repeat Off
For CDDA (audio CD) and data discs, the repeat options are:
1 TRACK (except for picture files) <-> ALL TRACK
<-> Shuffle Mode <--> Repeat Off
Note:
Some DVDs include subtitles in different languages. If you
want to choose subtitles, follow these steps.
Zoom
Press [ZOOM] during playback or still playback
to activate zoom function. Enables zoom in or
out the selected viewing at 1x, 2x, 3x and 4x.
Press [ꢂ] [ꢃ][ꢀ] [ꢁ] to move the highlighted
cursor to the desired selection on the on-
screen panel and press [ENTER].
Audio
To select a different audio language or
soundtrack during DVD playback. Press
[AUDIO] repeatedly to hear a different audio
languages or audio tracks.
Slow Motion
Enables the selection of a slow-motion speed.
You can choose to play the Disc at 1/2x and
1/4x.
Search
Initiates the search capability for locating a
desired position in the current title or track (time
search).
Note:
Press the numeric buttons (0 to 9) to enter the
desired time or title.
Multiple languages or soundtracks must be available on the
DVD.
Example (for DVD-VIDEO)
Angle
To select a different camera angle during DVD
playback. Press [ANGLE] repeatedly during
playback to select a desired angle.
To playback from
TITLE:CHAPTER : 001/001
or TIME:0 1 : 2 7 : 3 3 (H:M:S)
Example (for SVCD/VCD)
No
To playback from
TIME:0 1 : 2 7 : 3 3
Press [ꢂ] to correct a mistake.
Press [ꢂ] repeatedly to move back to the digit
where you entered a wrong number, and reenter
the correct one.
Press [ENTER] to start playback from the
specified time.
Note:
The Multiple Angles capability must be available on the DVD.
(within the current title) or track for playback.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Information
To enable or disable the DVD/VCD/SVCD disc
information.
TO EXIT NAVIGATION
Press [NAVI] again or repeatedly press [ꢂ] to
exit the “Navi” menu. Or go to “Exit” and press
[ENTER].
5. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to move the highlight to the
file you want to start playback from and press
[ENTER].
Playing back video title ( By Browser )
This unit can play video titles recorded on the HDD or the
recordable DVD disc.
6. Press [ꢀPAUSE/STEP] to pause playback.
Press [ STOP] to stop playback at a market
stop.
1. Place a disc with recorded video titles on the tray
or make sure that the video titles are saved on
the HDD.
Press [
STOP] twice to bring the playback to a full stop.
2.Press [HDD/DVD] to select HDD or DVD.
Note:
The index page numbers shown on the bottom of the browse
menu varies with the number of titles/files saved on the HDD/
DVD disc and do not always follow the numeric order. This is
designed for easier access to each page when there are more
titles/files available.
3. Press [BROWSER] and this will bringup the
browser menu with thumbnails.
If you want to view the text menu, move the cursor to the
“Text View” icon and press [ENTER].
If you want to change the playback device, press [ꢂ] [ꢃ] to
move the highlight to the “HDD” icon or “DVD” icon (depending
what the source is set as) and press [ENTER] to change the
setting.
4. Press [ꢂ] [ꢃ] to move the highlight to the “Video”
icon and press [ENTER] to view the file menu with
thumbnails.
If you want to view the text menu, move the highlight to the “Text
View” icon and press [ENTER].
32
Download from Www.Somanuals.com. All Manuals Search And Download.
MUSIC FILE PLAYBACK, PICTURE FILE PLAYBACK (BY BROWSER)
The unit can play an Audio CD, JPEG/BMP or MP3/WAV files
10. For JPEG files: The previous files of the selected file
on a disc or from the HDD.
cannot be played back.
Playing back music files
Playing back picture files
Playing back JPEG/BMP files.
Playing back MP3/WAV files.
1. Place a music disc on the tray or save the music
files to the HDD. Music files residing on the HDD
can be played from the hard disc.
1.Place a picture disc on the tray or save the
picture files to the HDD. Picture files residing on
the HDD can be played from the hard disk.
2. Press [HDD/DVD] to select HDD or DVD.
2.Press [HDD/DVD] to select HDD or DVD.
3. Press [BROWSER] on the list and this will bring up
the browser menu with thumbnails.
3.Press [BROWSER] on the list and this will bring up
the browser menu with thumbnails.
If you want to change the playback device, press [ꢂ] [ꢃ][ꢀ]
[ꢁ] to move the highlighted cursor to the “HDD” icon or
“DVD” icon (depending which source your desire) and press
[ENTER] to change the setting.
If you want to change the playback device, press [ꢂ] [ꢃ] [ꢀ]
[ꢁ] to move the highlighted cursor to the “HDD” icon or “DVD”
icon (depending what the source is set as) and press [ENTER]
to change the setting.
4. Press [ꢂ] [ꢃ] to move the highlighted cursor to
the “Music” icon and press [ENTER] to view the
file menu with thumbnails.
If you want to view the text menu, move the highlighted cursor to
the “Text View” icon and press [ENTER].
5. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to move the highlighted
cursor to the file you want to start playback from
and press [ENTER].
4.Press [ꢂ] [ꢃ] to move the highlighted cursor to
the “Picture” icon and press [ENTER] to view the
file menu with thumbnails.
Or, use the numbered buttoms and [ENTER] to select the music
file to start playback.
If you want to view the text menu, move the highlighted
cursor to the “Text View” icon and press [ENTER].
6. During playback, press [
NEXT ] or [
PREV] to advance to the next or return to
the previous file.
7. Press [ꢀPAUSE/STEP] to pause playback.
8. Press [ STOP] to stop playback at a market
stop.
5.Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to move the highlighted
cursor to the file you want to start playback from
and press [ENTER].
Press [
STOP] twice to bring the playback to a full stop.
Notes:
6.During playback, press [ꢂ] [ꢃ] to advance to the
next or return to the previous file.
1. If a MP3 file name includes any 2-byte character, the unit
may not display the file name correctly,
2. The unit cannot support ID3 tag.
3. The unit does not support MP3-Pro files.
4. The unit supports discs recorded with multiple sessions.
5. The unit can only playback picture or tracks with the following
file extensions; JPG or jpg, BMP or bmp, MP3 or mp3, WAV or
wav and etc.
6. The time required for reading disc contents may vary for
different discs. This is dependent upon the numbers of groups
(folders) and tracks (files) recorded and etc.
7.Press [ꢀ][ꢁ] to select “Rotate RIGHT” or “Rotate
LEFT” and “Rotate UP” or “Rotate DOWN.”
7. You cannot advance or reverse playback by pressing
[
FF] or [
REV ] during picture file playback.
8. This unit supports MP3 file bitrates of: 32Kbps ~ 320Kbps.
9. Customers should also note that permission is required in
order to download MP3 files and music from internet.
Sanyo has no right to grant such permission. Permission
should always be sought from the copyright owner.
8.Press [ꢀPAUSE/STEP] to pause playback.
9.Press [ STOP] to stop playback.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO CD PLAYBACK, PLAYBACK PICTURES AND MUSIC
Audio CD playback
Playing Audio CDs
8. During playback, press [
NEXT ] or [
PREV] to advance to the next or return to
the previous music file.
1. Place the Audio CD on the tray.
The disc will begin playback automatically.
9. Press [ꢂ] [ꢃ] to go to the next or return to the
previous picture file.
2. Press [
NEXT ] or [
PREV] to
Press [ꢀ][ꢁ] to select “Rotate RIGHT” or
“Rotate LEFT” and “Rotate UP” or “Rotate
DOWN.”
advance to the next track or reverse to the
previous track.
3. Press [ꢀPAUSE/STEP] to pause playback.
10. Press [ꢀPAUSE/STEP] to pause the playback.
Press [ STOP] to stop the playback.
4. Press [ STOP] to stop playback.
5. Enter the numbered button (0~9) to select the
desired audio track, and press [ENTER].
Begin playing from a selected track.
Slide show (Pictures with Music)
Concurrent playing of pictures and music files on the
same disc.
1. Place the disc with the audio and the picture files
on the tray or make sure that the audio and
picture files are saved onto the HDD. The saved
audio and music files can be played from the hard
disk.
2. Press [GUIDER] for the Easy Guider Menu.
3. Press [ꢀ] [ꢁ] to go to the “Playback” icon and
press [ENTER].
4. Press [ꢀ] [ꢁ] to select HDD or DVD to play the
files from and press [ENTER].
Note:
Music and picture files can be played concurrently when these
files are saved onto the same device.
5. Press [ꢀ] [ꢁ] to go to the “Pictures with music”
icon and press [ENTER].
The browser menu of picture files will be displayed first.
6. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to select the picture file to
start playback with and press [ENTER].
The browser menu of audio files will be displayed.
7. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to select the music file to
start playback with and press [ENTER].
Playback will start.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
COPY
This DVD recorder is equipped with “One Touch Copy” feature,
which allows you to copy recorded files from the HDD to DVD or
from DVD to HDD. This function is only applicable to JPEG, BMP,
VOB, MP3 and WAV files and recorded video titles(HDD to DVD
only).
Copying from HDD to DVD
1. Press[ STANDBY/ON]toturntheunitandyourTVon.
2. Press [ OPEN/CLOSE ] to open the disc tray and
place a recordable DVD disc with the label side up.
Make sure to insert a recordable DVD disc.
Note:
As for the audio CD copied on HDD, there are no relations to the
original track number, the music which played back first may be
Press the button again to close the tray.
indicated with “01”.
When you insert a new recordable DVD disc, the DVD recorder
automatically starts the disc preparation process.
When playback musics of audio CD which are copied to HDD;
SHUFFLEplayback
Shuffle playback can only be played back after the selected
3. Press [HDD/DVD] and select “HDD.”
4. Press [BROWSER] to browse the files.
music.
PREVIEW
The previous musics of the selected music cannot be played
back.
5. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to move the highlighted
cursor to the file to be copied and press [COPY].
The file is then copied to the DVD disc.
CopyingfromDVDtoHDD
1. Press[ STANDBY/ON]toturntheunitandyourTVon.
Note:
2. Press [ OPEN/CLOSE ] to open the disc tray and
place the disc with the label side up.
3. Press [HDD/DVD] and select “DVD.”
4. Press [BROWSER] to browse the files.
5. Press [ꢀ] [ꢁ][ꢂ] [ꢃ] to move the highlight
cursor to the file to be copied and press [COPY].
The file is then copied to your HDD.
Notes:
1. Video files with “DVD-Video” in its file
name and the thumbnail below can only be
copied to an emptied/new DVD+R/+RW
disc.
2. Video files with “VCD-Video” in its file
name and the thumbnail above can only be
copied to a CD-R/RW prepared as a VCD disc.
3. Video files with “SVCD-Video” in its file name and the
thumbnail above can only be copied to a CD-R/RW prepared as
a SVCD disc.
4. Before copying other files to a disc, reference the below:
Notes:
1. Contents recorded on a VCD/SVCD disc can not be copied
to the HDD before the disc is finalized.
2. The title of DVD-Video cannot be copied from DVD to HDD.
3. You can’t use the One Touch Copy function to copy a title if
any part of the title is copy-once protected.
4. You may use this product only to reproduce or copy
materials for which you own the copyright or have which
obtained permission to copy from the copyright owner or
for you otherwise have a legal right to reproduce or copy.
Unless you own the copyright or have obtained permission
from the copyright owner or otherwise have a legal right to
reproduce or copy, you may be violating the law, including
copyright law, and may be subject to payment of damages
and other remedies.
*1. Recorded titles are titles with recording quality (HQ, SP, LP, EP,
SLP) information in the browser menu.
*2. CD-R/RW disc prepared in the Audio CD format can only be
used to copy WAV music files. When copying is completed, you
need to first "finalize" the disc before you can play the disc on a
compatible device.
*3. If you copy recorded titles to a blank DVD+R/+RW disc, you can't
use the same disc to copy data files. If you copy data files to a blank
DVD+R/+RW disc, you can't use the same disc to copy recorded
video titles.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
EDIT
Before starting to edit
This section explains the basic editing functions on the unit.
Please finish all the editing before finalizing the disc. You cannot
edit the contents on a finalized disc.
You can perform the editing functions on video titles only.
Notes:
1. For DVD+R discs, after performing editing function of
inserting, renaming or hiding chapter marks to a video title,
the setting will NOT be valid when playing the disc(s) on
another DVD player/recorder.
Protecting a title (HDD and DVD)
You can protect the title from accidental erasure or editing when
you activate the protect function.
When protection is turned “ON,” the title can’t be edited or
erased.
If you do need to edit it, you must first unlock the file.
1.Press [BROWSER] to display the “Browser” menu.
2. Editing functions introduced in this chapter is NOT appli-
cable to video titles recorded on CD-R or CD-RW discs.
2.Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit and then press [EDIT] to go to the edit
screen.
Browser menu
1. Press [ STANDBY/ON] and press [HDD/DVD] to
select the “DVD” or “HDD” to browse from.
3.Press [ꢀ] [ꢁ] to select “Protection” and then
press [ENTER].
2. Press [BROWSER] to display the “BROWSER”
menu.
4.Press [ENTER] to select “On” or “Off.
3. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit, and press [EDIT] to go to the edit screen.
5.Press [ꢀ] [ꢁ] to select “Exit” and then press
[ENTER].
Naming a title (HDD and DVD)
1. Press[ꢀ] [ꢁ] to select “Rename” and then press
Note:
[ENTER].
You CANNOT protect the recorded title(s) on a DVD+R disc
if the disc is finalized.
Overwriting a title (DVD only)
1. Press [HDD/DVD] to select the “DVD.”
2. Press [BROWSER] to display the “Browse” menu.
3. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit and then press [EDIT] to go to the edit
screen.
2. The menu for the title naming is displayed.
4. Press [ꢀ] [ꢁ] to go to“Overwrite” and then
press [ENTER] to set it on or off.
The “Overwrite” mode is set.
3. Press [ꢀ] [ꢁ] to select the “Clear” icon first and
then press [ENTER] before start entering the new
title. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select “Back” to
delete characters.
4. Use [ꢂ] [ꢃ] [ꢀ] [ꢁ] and [ENTER] on the remote
control to select desired characters.
5. Press [ꢀ] [ꢁ] to select “Exit” and then press
5. When you finish entering the title, press [ꢂ] [ꢃ]
[ꢀ] [ꢁ] to select “Finish” and press [ENTER].
Notes:
1. You only can enter up to 30 characters for a name. You
can not leave the title column blank.
[ENTER].
Note:
The “overwrite” function is not applicable to video titles saved
on the HDD or a DVD+R disc that is finalized.
2. If you wish to enter “space”, select a blank on the
keypad and press [ENTER].
36
Download from Www.Somanuals.com. All Manuals Search And Download.
EDIT
Notes:
Splitting a title (HDD or DVD+RW only)
1. For video titles recorded on a DVD+RW disc, you can only
merge the title with its previous/next title and only when the
previous/next title has the same recording quality, TV signal,
audio and video settings. Otherwise, the function will not be
applicable.
2. For video titles recorded on the built-in HDD, you can merge
the title with any of the titles recorded on the HDD with the
same recording quality, TV signal, audio and video setting.
Use this function to divide a title into two distinct sessions. After
splitted, the new title can still be merged again. This function is
only applicable to titles with length longer than 6 seconds.
1. Press [BROWSER] to display the “Browser”
menu.
2. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit and then press [EDIT] to go to the edit
screen.
3. Press [ꢃPLAY] to start the title playback first.
Press [
NEXT] or [
PREV] to advance
Erasing a title (HDD and DVD only)
Use this function to erase a title.
Note that once erased, the title(s) cannot be retrieved.
to the next chapter or the previous chapter.
Press [
FF] or [
REV ] to perform fast
forward or fast rewind scanning.
1. Press [BROWSER] to display the “Browser” menu.
4. Move the highlighted cursor to “Split” and press
[ENTER] for confirmation.
2. Use [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want to
edit and then press [EDIT] to go to the edit screen.
The title is splitted into two titles at where you press [ENTER]
during playback.
3. Press [ꢀ] [ꢁ] to select “Erase”.
5. When complete, the browser menu will be displayed.
4. Press [ENTER] to confirm your setting.
The title selected is erased.
6. To split more titles,
repeat from step 2 to
4. Or press [ꢀ] [ꢁ] to
select “Exit” and then
press [ENTER] to exit
the setting.
Note:
The split function is only
applicable to video titles
longer than 6 seconds.
5. To erase more titles, repeat from step 2 to 4. Or
press [ꢀ] [ꢁ] to select “Exit” and then press
[ENTER] to exit the setting.
Merging two titles into one (HDD or DVD+RW only)
Note:
Use this function to merge two titles into one.
You CANNOT erase recorded title(s) on a DVD+R disc if
the disc is finalized.
After merged, the new title can still be splitted again.
1.Press [BROWSER] to display the “Browser” menu.
2.Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit and then press [EDIT] to go to the edit
screen.
Setting a title thumbnail (HDD and DVD only)
Normally the first picture of a recording is used as the index
picture. However, you can choose any picture from the recording
as the index picture.
3.Press [ꢀ] [ꢁ] to select “Merge with...” and then
press [ENTER].
1.Press [BROWSER] to display the “Browser” menu.
A menu shows all the titles applicable to this function will
display.
2.Use [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want to
edit and then press [EDIT] to go to the edit screen.
4.Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title to merge
and then press [ENTER].
3.Press [ꢃPLAY] to start the title playback first.
Press [
NEXT] or [
PREV] to advance to
the next chapter or the previous chapter.
Press [
FF] or [
REV ] to perform fast
forward or fast rewind scanning.
Press repeatedly to play the title forward or reverse.
5.To merge more titles, repeat from step 2 to 4. Or
press [ꢀ] [ꢁ] to select “Exit” and then press
[ENTER] to exit the setting.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
EDIT
Notes:
1. You CANNOT insert chapter marks to recorded title(s) on a
DVD+R disc if the disc is finalized.
4.Press [ꢀ] [ꢁ] to select “Set Thumbnail.”
2. When not in the EDIT menu, press [EDIT] during normal
recording can add chapter marks in the recorded session(s)
manually.
Erasing Chapter Mark (HDD and DVD only)
During playback you can set and erase chapter mark(s) within a
title.
1. Press [BROWSER] to display the “Browser” menu.
5.Press [ENTER] to select the image during playback
and set it as the video title thumbnail.
2. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit, and then press [EDIT] to go to the edit
screen.
6. To set thumbnails for more titles, repeat from step
2 to 5. Or press [ꢀ] [ꢁ] to select “Exit” and then press
[ENTER] to exit the setting.
Note:
You CANNOT set the thumbnail for the recorded title(s) on
a DVD+R disc if the disc is finalized.
Inserting chapter mark (HDD and DVD only)
During playback you can set and erase chapter mark(s) within a
title.
3. Press [ꢀ] [ꢁ] to select “Remove Chapter Mark”.
1. Press [BROWSER] to display the “Browser” menu.
4. Press [ꢃPLAY] to start the title playback first.
2. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit, and then press [EDIT] to go to the edit
screen.
Press [
NEXT] or [
PREV] to advance
to the next chapter or the previous chapter.
Press [
FF] or [
REV ] to perform fast
forward or fast rewind scanning.
Press repeatedly to play the title forward or reverse.
5. During playback you can press [ENTER] to erase
the chapter mark.
6. To erase chapter marks in more titles, repeat from
step 2 to 5. Or press [ꢀ] [ꢁ] to select “Exit”
and then press [ENTER] to exit the setting.
Notes:
3. Press [ꢀ] [ꢁ] to select “Insert Chapter Mark”.
1. This function is not applicable to files without any chapter
marks.
2. The first chapter mark within a video title can not be erased.
4. Press [ꢃPLAY] to start the title playback first.
Press [
NEXT] or [
PREV] to advance to
the next chapter or the previous chapter.
Press [
FF] or [
REV ] to perform fast
forward or fast rewind scanning.
Press repeatedly to play the title forward or reverse.
5. Press [ENTER] to insert chapter marks at where
you want to during playback.
6. To insert thumbnails in more titles, repeat from
step 2 to 5. Or press [ꢀ] [ꢁ] to select “Exit”
and then press [ENTER] to exit the setting.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
EDIT
Hiding Chapter (HDD and DVD only)
Showing Chapter (HDD and DVD only)
During playback you can set and hide chapters within a title.
During playback you can choose to show chapter(s) cur-
rently hidden within a title.
1. Press [BROWSER] to display the “Browser” menu.
1. During playback, press EDIT to display the Edit
menu.
2. Press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select the title you want
to edit, and then press [EDIT] to go to the edit
screen.
2. On the Edit menu, press[
NEXT] or [
PREV ]
to select the hidden chapter you would like to
show again.
3. Press [ꢀ] [ꢁ] to select “Hide Chapter.”
Notes:
4. Press [ꢃPLAY] to start the title playback first.
1. On the Edit menu, a hidden chapter mark is displayed in a
darker color. A message “Hidden” is also displayed at the
left bottom corner of the PIP window.
Press [
NEXT] or [
PREV ] to advance
to the next chapter or the previous chapter.
Press [
FF] or [
REV ] to perform fast
2. You can press [ꢀPAUSE/STEP] to pause playback before
you go on to step 3 and 4 to show the hidden chapter.
forward or fast rewind scanning.
Press repeatedly to play the title forward or reverse.
3. Select the "Show Chapter" by using cursor button
then press [ENTER] for showing chapter again.
5. During playback you can press [ENTER] to hide a
chapter.
4. To show more chapters within the title, repeat
steps 1 to 3. Or press [ꢀ] [ꢁ] to select “EXIT”,
then press [ENTER] to exit the setting.
6. To show (un-hide) the hidden chapter, press [ꢀ]
[ꢁ] to go to “Show Chapter” and press [ENTER]
during the playback of the hidden chapter.
Press [
NEXT] or [
PREV ] to advance to the next
chapter or the previous chapter.
7. To hide more chapters within the title, repeat from
step 2 to 5. Or press [ꢀ] [ꢁ] to select “Exit”
and then press [ENTER] to exit the setting.ote:
Notes:
1. You CANNOT hide chapters within recorded title(s) on
a DVD+R disc if the disc is finalized.
2. This function is not applicable to titles without chapter
marks.
3. After performing this function, the chapter marks within the
title are hidden only during playback.
4. In Edit mode, a hidden chapter mark is displayed in a darker
color. A message “hidden” is also displayed at the left
bottom corner of the PIP.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC TOOLS
Finalize (make compatible)
Erase
Before you begin erasing any contents on a disc or the HDD,
please ensure that all important contents are safely backed-up.
All contents will be permanently erased.
CAUTIONS:
For DVD+R/CD-R/CD-RW discs:
CAUTIONS:
Finalizing a disc is a necessary step when you want to share
your digital content with others. Once a DVD+R or a CD-R/RW
disc is finalized, it can be played back on other DVD players
or on PCs.
For DVD+RW and CD-RW discs, you can erase the contents
and create a new format with the erase function. You can use
the erase function to empty the HDD as well.
Note:
1. Press [TOOLS] to display the “DISC TOOLS”
Menu.
For DVD+RW discs, finalizing is NOT required.
2. Press [ꢀ] [ꢁ] to select “Erase” and then press
1.Press [TOOLS] to display the “DISC TOOLS” Menu.
[ENTER].
2.Press [ꢀ] [ꢁ] to select the “Finalize” icon and
then press [ENTER].
The finalization process will take place.
3. Press [ꢀ] [ꢁ] to select “DVD” or “HDD” and
press [ENTER].
3.When complete, go to “Exit” and press [ENTER].
4. Press [ENTER] to start erasing.
The erasing process will take place.
5. When complete, go to “Exit” and press [ENTER].
Note:
If a new recordable CD-R or a newly-erased CD-RW is used for
recording, press [ꢂ] [ꢃ] [ꢀ] [ꢁ] to select a disc format the
disc is to be prepared as and press [ENTER] : SVCD, VCD,
Audio CD or Data CD.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC TOOLS
CleanUp Disc (HDD only)
Defragment (HDD only)
1. Press [TOOLS] to display the “DISC TOOLS”
Menu.
The “Defragment” process reorganizes the contents of the HDD
creating continuous blocks of available space.
2. Press [ꢀ] [ꢁ] to select the “Clean Up HDD,” and
1. Press [TOOLS] to display the “DISC TOOLS”
Menu.
then press [ENTER].
2. Press [ꢀ] [ꢁ] to select “Defragment” and
then press [ENTER]. “Go !” is selected and press
[ENTER].
The defragment operation begins.
3. Press [ꢀ] [ꢁ] to select the “Delete Older Files,”
“Delete Larger Files,” “Delete Seldom Played
Files,” “Delete Album” or “Delete All” and then
press [ENTER].
3. When the “Defragment” process is completed,
press [ENTER] to exit the “DISC TOOLS” menu.
Notes:
1. Contents of the HDD will not be lost during this process.
2. Frequent “defragment” operations are recommended to
improveperformance.
3. During the defragment operation, you can press [TOOLS]
or move to “Exit” and press [ENTER] to exit the defragment
menu.
4. The clean up process will take place.
You will be asked to confirm the operation step by step by
pressing [ENTER] to each question.
5. When complete, move the highlighted cursor to
“Exit” and press [ENTER] to exit.
Notes:
1. The “Cleanup” operation will permanently delete the files
selected.
2. It would take more time for the “Cleanup” operation
depending on the recorded condition.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
GUI(GRAPHICAL USER INTERFACE) OPERATION
Language
System
Video Output
Menu Language
Select a menu operating language. The options are :
English, French, German, Italian, Spanish
Switch video output signal.
Component
Scart S-Video
Scart RGB(Default)
Progressive
Audio Language
Select an audio operating language. The options are :
English, French, German, Italian, Spanish
Note: If you are connecting the DVD recorder to the TV via
the SCART OUT jack, set the VIDEO OUTPUT as
either “Scart S-Video” or “Scart-RGB.” If you
are connecting the DVD recorder to the TV via
the COMP OUT jack, set the VIDEO OUTPUT
as “Component.”
Subtitle Language
Select a subtitle operating language. The options are :
English, French, German, Italian, Spanish, Off
Date
Set the date of the system clock.
Time
Set the time of the system clock.
HH:MM:SS
Auto-Sleep
Off/30/60/90/120mins(Default: Off)
Note:
“Auto sleep” sets how long the DVD recorder is switched to
“STANDBY” mode when no operation of the system is
detected (e.g. recording, playback, timer record or editing).
Playback
Restore
---- (Off)
Restore
Aspect Ratio
Settings of audio and video parameters when playing back.
16:9 Wide
4:3 Pan
4:3 L.Box (Default)
Parental Lock
Audio
Digital Out
Set content control for supported DVD.
Set Level (Off , 1~8 ) (Default: off)
Settings of digital audio output.
The parental control levels are:
PCM (Enable digital audio output with PCM data)
1: Kid Safe
4: PG-13
7: NC-17
2: G
3: PG
6: R
Off (Default)
Bit Stream (Enable digital audio output with encode
data)(Default)
5: PG-R
8: Adult
DTS Out
Password
Set a system protect password. Password is needed for the
changing the setting.
Enable/Disable Digital Theater System output.
ON (Enable Digital Theater System mode)
OLD Password (XXXX)
Confirm
NEW Password (XXXX)
OFF (Disable Digital Theater System mode) (Default)
(XXXX)
*(Default:0000)
Surround
Slide Time
Stereo
Dolby(Default)
DTS
Set the slide show interval while playing JPEG files.
Off
VCD PBC
3~99 Seconds (Default: 5)
TV Sound Bilingual
Main(Default)
Sub (Second Audio Program)
Enable/Disable play back control for VCD and SVCD.
ON (Default) OFF
MPEG
PCM (Default)
Bit Stream
42
Download from Www.Somanuals.com. All Manuals Search And Download.
GUI(GRAPHICAL USER INTERFACE) OPERATION
Record
Mode( Record Quality )
Set the default quality of recording.
HQ
EP
SP (Default)
SLP
LP
Chapter Mark
Set the interval of chapter auto-insertion while recording.
Off 5/10/15/20/25/30 mins (Default: 5mins)
1) Press [SETUP] to display the setupmenu.
2) Press [ꢀ] [ꢁ] to select “System,” “Language,”
“Playback,” “Record,” “Audio,” “TV Tuner” or
“Exit” and press [ꢃ] or press [ꢂ] to return to previous
layer.
3) Press [ꢀ] [ꢁ] to select the item and press [ꢃ] or
[ENTER].
4) Press [ꢀ] [ꢁ] to set the option and press [ENTER].
To exit the SETUP menu
Press [SETUP] or press [ꢂ] until you return to the main menu.
TV Tuner
TV Signal ---> Antenna or Cable or Auto
(Select the type of antenna input)
Country ---> Select your location
Utilities ---> Scan channel or Edit channel
(Select to start rescanning channel or edit a channel)
Fine Tune --> -24 ~ -1 0 +1 ~ +24
(Select to fine tune the channel frequency manually)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
DVD+RW
576i/576p
DVD+RW is a recordable and rewritable disc. Recording can be
erasd and you can record on the same disc again for the
maximum of 1,000 times. DVD+RW use a recording format that
is comparable to a DVD-Video format.
Indicates the number of scanning lines and scanning format of
an image signal.
576i indicates 576 scanning lines with interlace format, and
576p indicates 576 scanning lines with progressive format.
Interlace output
Aspect ratio
NTSC, the video signal standard, has 480 interlaced (I) scan
lines, The Interlaced scanning system places lines of the
second half of the picture in-between lines of the first half of the
picture.
Aspect ratio refers to the length to height ratio of TV screens.
The ratio of a standard TV is 4:3, while the ratio of a high-
definition or wide TV is 16:9. The letter box allows you to enjoy
a picture with a wider perspective.
Bitstream
JPEG
The digital form of multi-channel audio data (e.g., 5.1-channel)
before it is decoded into its various channels.
A popular file format for still image compression and storage.
JPEG stands for “Joint Photographic Experts Group”. There are
two sub-types of the JPEG format as follows.
•
•
Baseline JPEG: used for digital cameras, the web, etc.
Lossless JPEG: an old type, rarely used now.
Chapter / Title
Chapter is the smallest division and title is the largest division
on a DVD VIDEO. A chapter is a division of a title and similar to
a track for Video CD or Audio CD.
Linear PCM audio
PCM stands for “Pulse Code Modulation”. Linear PCM is the
usual method for digitally encoding audio without compression,
and is used for the audio tracks on DVD VIDEO discs, Audio
CDs, etc.
Component video
Video signals with three channels of separate information that
makes up the picture. There are some types of component
video, such as R/G/B and Y/Cb(Pb)/Cr(Pr).
MP3
MP3 (MPEG1 audio layer 3) is a compressed audio file format.
Files are recognized by their file extension “.mp3” or “.MP3”.
Composite video
A single video signal commonly used in most consumer video
products that contains all luminance, color, and synchronization
information.
MPEG
MPEG stands for “Motion Picture Experts Group”. This is an
international standard for compression of moving images.
On some DVDs, digital audio has been compressed and
recorded in this format.
Dolby Digital®
A six-channel system consisting of left, center, right, left rear,
right rear and LFE (Low-Frequency Effect channel, for use with a
sub-woofer) channels. It requires a Dolby Digital® decoder,
either in the player or in an external receiver to regenerate the
sound. All processing is done in the digital domain.
Not all Dolby Digital discs contain six (5.1) channels of
information.
NTSC (National Television System Committee)
The initials stand for National Television Standards Committee.
This is the committee that established the standards for
television systems in the United States. The NTSC standard
broadcasts 525 or 480 lines of resolution per second, and 30
frames per second of refresh rate, 60 Hz field frequency. NTSC
TV system is widely used in USA, Canada, Latin America and
Taiwan etc.
DTS® (Digital Theater Systems)
DTS® stands for Digital Theater Systems. DTS® is a Digital
Surround audio encoding format configured with six (5.1)
channels, similar to Dolby Digital®. It requires a DTS® decoder,
either in the player or in an external receiver to regenerate the
sound. All processing is done in the digital domain.
Not all DTS discs contain six (5.1) channels of information.
PAL (Phase Alternation by Line)
PAL (Phase Alteration Line) is the color television broadcast
standard throughout the Western Europe (except in France,
where SECAM is the standard), Australia, China, Singapore and
Malaysia etc. It has 625 lines of vertical resolution per second
and 25 frames per second refresh rate, 50 Hz field frequency.
DVD-R
DVD-R is a recordable disc that is the same size as a DVD-
Video. Contents can be recorded only once to a DVD-R,and will
have the same format as a DVD-Video.
PBC
Playback Control. A special feature on a Video CD or Super
VCD that enables interactive use.
DVD-RW
DVD-RW is a recordable and rewritable disc that is the same
size as a DVD-Video. DVD-RW has two different modes: VR
mode and Video mode.DVD created in video mode has the
same format as a DVD-Video ,while discs created in VR(Video
Recording)mode allow the contents to be programmed or edited
S-Video
A video signal which improves picture quality over standard
composite connections. Used on Super VHS, DVD, high end TV
monitors, etc.
Track
DVD+R
SVCD, VCD, Audio CD discs use tracks to divide up the content
of a disc.
DVD+R is a recordable disc that is the same size as a DVD-
Video. Contents can be recorded only once to a DVD+R,and will
have the same format as a DVD-Video.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
DISC TYPES SUPPORTED (Read Only):
DVD-R/RW, DVD+R/RW, CD-R/RW
AUDIO FORMAT SUPPORDED - Playback
Analog output
Digital output
2channel
coaxial/optical
LPCM
Format supported
Dolby Digital
dts (only digital out)
MPEG
CONTENT FORMAT SUPPORTED :
1) DVD-Video
2) DVD+VR (DVD+VR format is compatible with DVD-Video in
most case)
3) Video CD
4) Super VCD
AUDIOPERFORMANCE
DAConverter
24-bit/96KHZ
24-bit/96KHZ
≥90dB
≥80dB
≥110dB
5) Audio CD
6) VOB/MPG/DAT
ADConverter
7) MP3/WAV
Signal-Noise (1kHz)
Dynamic Range (1kHz)
Cannel Separation (1kHz)
Maximum number of files recognizable : 9999 files
Compression rate : between 32 kbps and 320 kbps
8) JPEG/BMP
Total Harmonic Distortion (1kHz) ≤-65dB
Maximum number of pictures recognizable : 9999 files
TUNER
TVformat
RECORDABLEMEDIASUPPORTED:
PAL-B/G, PAL-D/K, PAL-I/I
or SECAM-L/L
1) Bulit-in HDD
(DVD+VRmode)
(This recorder is designed to record and play back using the
PAL coloring system.)
2) DVD+R/DVD+RW
3) CD-R/CD-RW
( DVD+VR Mode )
( VCD/SVCD mode)
TV sound
Main / Sub
VIDEORECORDINGMODE
Mode
DVD
160GB
HDD
CONNECTIONS
FRONT PANEL
Video Input
Audio L/R Input
DV Input
Cinch (yellow) x1
Cinch (white/red) x1
IEEE 1394 4-pin x1
HQ
1hr
33hrs
66hrs
99hrs
132hrs
198hrs
N/A
SP
2hrs
LP
EP
SLP
Just Fit
3hrs
4hrs
6hrs
REARPANEL
Video Output
Variable
Cinch (yellow) x1
Audio L/R Output
Component /
Progressive Scan Output
Cinch (white/red) x1
Mode
CD-R/CD-RW
Y, Pb
,P (Green/Blue/Red) x1
r
576p output
VCD
68 mins
34 mins
66 mins
SVCD
Audio CD
SCART1
SCART2
CVBS/RGB/S-Video out
CVBS/RGB in
DigitalAudio Output
Coaxial
Optical
x1
x1
VIDEO RECORDING FORMAT
MPEG2: DVD+VR (HQ/SP/LP/EP mode) , SVCD
MPEG1: DVD+VR (SLP mode) , VCD
GENERAL
Power Supply
Power Consumption
AC100~240V 50/60Hz
50W (Operation mode)
Less than 5W (Standby mode)
+5°C to +40°C
AUDIO RECORDING FORMAT
DVD+VR (HQ/SP/LP/EP/SLP mode) : Dolby Digital 2-channel
VCD/SVCD : MPEG1 Layer2
Operating Temperature
Operating Humidity
Dimensions(W/H/D):
Net Weight:
5% to 80% RH
CD-DA : PCM
430 x 66 x 316 mm
Approx. 4.5 kg
VIDEOPERFORMANCE
DAConverter
10-bit / 54MHz
Composite Output
Components Output
1 Vpp 75 Ohm
Y : 1 Vpp 75 Ohm
Pb: 0.7 Vpp 75 Ohm
Pr : 0.7 Vpp 75 Ohm
Note:
The specifications and design of this product are subject to
change without notice.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Picture
No playback on DVD recorder.
--> There’s no recording on the disc. Check the disc first.
--> A unplaybackable disc type is inserted. Check the playable
disc type list.
--> The way you inserted the disc is wrong. Insert the disc
with the label side facing up. If there’s no label on the disc,
check the disc retailer.
--> Wrong region code: The region code on the recorder and
the disc must match.
--> Parental control is on: you have to unlock it first. (default
code of the recorder: 0000)
The image from this unit does not appear on the
television.
--> Make sure that the TV is connected to the AV OUTPUT,
SCART OUT or COMP OUT terminals on this unit. (refer to
“CONNECTIONS” section)
--> Make sure that the television’s input setting is correct.
--> Make sure that a disc is well-placed on the disc tray and is
compatible to the local TV system ( PAL)
--> Check whether the recorder is set to progressive with an
incompatible TV. Reset by pressing [ꢃ], “5,” “0,” “2,” and “0”
on the remote control and then press [ENTER].
--> Check of the cables are secured between the TV set and
the recorder.
Timer Recording
The image from this unit appears with noises.
--> The disc is distorted or flawed.
Timer recording does not work properly
--> The timer program is incorrect. Correct the program.
--> Different timer program times overlap.
--> The clock setting is wrong. Go to setup to set the right time and
date.
--> An already finalized DVD+R has been inserted: change disc.
--> If the picture output signal from the recorder passes through
your VCR to get to your TV, or if you are connected to a
combination T V/VIDEO player, the copy protection signal
applied to some DVD programs could affect picture quality. If
you still experience this problem even when you connect your
recorder to your TV, try connecting your recorder to your TV’s
S-VIDEO output.
The timer program remains even after recording
finishes.
--> The timer program remains if set to daily or weekly.
The image from an external input is distorted.
--> If the video signal from the external component is copy-
protected, you can not connect via the recorder. Connect the
component directly to your TV.
Recording
Can’t record.
--> You haven’t inserted a disc or the disc you inserted cannot be
recorded on. Insert a disc the unit can record onto.
Sound
An alternate audio track cannot be recorded.
--> Second Audio Program (SAP) is not available for all programs.
--> The recorder does not feature “SecondAudio Program (SAP)”
function.
There is no sound
--> Check the audio cable connection.
--> Check if the audio cord is damaged.
Recording does not start immediately after you
--> The input source setting on the amplifier is incorrect.
--> There’s no sound when the picture is paused or during
scanning (even forwards at regular playback speed) or slow
motion play. Press [ꢃPLAY] to resume regular playback.
--> If the audio signal does not come through theDIGITAL OUT
(OPTICAL or COAXIAL) jacks, check the AUDIO OUT settings.
press[ REC].
ꢁ
--> Disc preparation process is taking place and will take a short
while. (applicable to DVD+R/RW discs)
Can’t record on HDD.
--> If there is a power failure or the plug is disconnected from the
householdAC outlet while recording or editing, the HDD may
become unusable. You will have to go to “DISC TOOLS” to
“Erase” the contents on the HDD. Data recovery is NOT
guaranteed.
The sound from this unit is not presented prop-
erly or is distorted.
--> Check the audio cable connection.
--> Check if the audio cord is damaged.
TV channel
--> Make sure that the amplifier/receiver or TV is set to the correct
input and the volume is turned on.
TV channels cannot be changed.
--> Switch the input signal source of the recorder to “TV.”
--> Connect the antenna cables correctly.
--> If the sound is distorted, try cleaning the cable plugs.
Playback
Others
Can’t playback a disc recorded using this re-
corder or another player
The disc does not open/close.
--> Contact your local dealer or local authorized service facility.
--> If the disc was recorded in video mode, make sure that it’s
finalized.
The unit stops at “HELLO” and does not respond
to any other commands.
--> Some players will not play recordable DVD discs when
recorded in video mode and finalized.
--> Discs recorded with copy-once material cannot be played
on non-CPRM compatible players.
--> Turn the unit off and turn it on again. If the unit still does not
respond to any commands, unplug the power cord, reconnect
it and turn it on again. Contact local dealer or authorized
service facility if the unit still does not work.
The recorder starts playing the disc
automatically.
If you forget the password...
--> Please enter "8008" on password setting mode for pass-
word clear.
--> TheDVDVIDEO features an auto playback function.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SANYO Electric Co., Ltd.
P/N: 87819901114--
Download from Www.Somanuals.com. All Manuals Search And Download.
|
RCA Camcorder CC634 User Guide
Rosewill Computer Drive RC218 User Guide
Rotel Stereo Amplifier RA 611 User Guide
Samson Headphones C02 User Guide
Samsung Digital Camera TL210 User Guide
Samsung Telephone SP C700R User Guide
Sanyo Battery Charger HR AUC User Guide
Scag Power Equipment Lawn Mower SW 20KHE User Guide
SECO LARM USA Home Security System VA 1102B WQ User Guide
Senco Air Compressor PC2014 User Guide