INSTRUCTION MANUAL
Sterilizer
MOV-112S
MOV-212S
Библиотека Ладовед.
OCR Юрий Войкин 2008г.
MOV-212S
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
1. No part of this manual may be reproduced in any form without the expressed written
permission of SANYO.
2. The contents of this manual are subject to change without notice.
3. Please contact SANYO if any point in this manual is unclear or if there are any
inaccuracies.
SANYO Electric Biomedical Co., Ltd.
All rights reserved.
Printed in Japan.
CONTENTS
PRECAUTIONS FOR SAFE OPERATION
CAUTIONS FOR USAGE
P. 2
P. 6
P. 6
ENVIRONMENTAL CONDITIONS
STERILIZER COMPONENTS
INSTALLATION
P. 7
P. 10
P. 11
BEFORE COMMENCING OPERATION
OPERATING INSTRUCTIONS
ALARM & SAFETY FUNCTIONS
P. 12
P. 17
ROUTINE MAINTENANCE
TROUBLE SHOOTING
DISPOSAL OF UNIT
SPECIFICATIONS
P. 18
P. 19
P. 19
P. 20
PERFORMANCE
P. 20
P. 21
SAFETY CHECK SHEET
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONSFORSAFEOPERATION
WARNING
Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to
rain water.
Only qualified engineers or service personnel should install the unit. The installation by
unqualified personnel may cause electric shock or fire.
Install the unit on a sturdy floor. If the floor is not strong enough or the installation site is not
adequate, this may result in injury from the unit falling or tipping over.
Never install the unit in a humid place or a place where it is likely to be splashed by water.
Deterioration of the insulation may result which could cause current leakage or electric shock.
Never install the unit under the water main or vapor pipe. Deterioration of the insulation may
result which could cause current leakage or electric shock.
( \ j Never install the unit in a flammable or volatile location. This may cause explosion or fire.
Never install the unit where acid or corrosive gases are present as current leakage or electric
shock may result due to corrosion.
Use a dedicated power source as indicated on the rating label attached to the unit.
Remove dust from the power supply plug before inserting in a power source. A dusty plug or
improper insertion may pose a hazard.
Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet
is not grounded (earthed), it will be necessary to install a ground by qualified engineers.
x ~\ Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such
grounding may cause electric shock in the case of an incomplete circuit.
Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet for inner air
0
circulation. This may cause electric shock or injury by accidental contact with moving parts.
( \ j Never store volatile or flammable substances in this unit. This may cause explosion or fire.
Use this unit in a safe area if using poisonous, harmful or radioactive substances. Improper
use may be harmful to your health or the environment.
Disconnect the power supply to the unit prior to any repair or maintenance in order to prevent
electric shock or injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONSFORSAFEOPERATION
!\WARNING
Ensure you do not inhale or consume medication or aerosols from around the unit at the time of
maintenance. These may be harmful to your health.
Never splash water directly onto the unit as this may cause electric shock or short circuit.
Never disassemble, repair, or modify the unit yourself. Any such work carried out by an
unauthorized person may result in fire or injury due to a malfunction.
Disconnect the power supply plug if there is anything wrong with the unit. Continued abnormal
operation may cause electric shock or fire.
If the unit is to be stored unused in an unsupervised area for an extended period, ensure that children
do not have access and that doors cannot be closed completely.
The disposal of the unit should be undertaken by appropriate personnel. Remove doors to
prevent accidents such as suffocation.
Prepare a safety check sheet when you request any repair or maintenance for the safety of service
personnel.
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS FOR SAFE OPERATION
CAUTION
Select a level and sturdy floor for installation. This precaution will prevent the unit from tipping.
Improper installation may result in water spillage or injury from the unit tipping over.
Connect the unit to a power source as indicated on the rating label attached to the unit. Use of
any other voltage or frequency other than that on the rating label may cause fire or electric shock.
tfB Fix the shelves securely. Incomplete installation may cause injury or damage.
When removing the plug from the power supply outlet, grip the power supply plug, not the cord.
Pulling the cord may result in electric shock or fire by short circuit.
Never damage or break the power supply plug or cord. Do not use the supply plug if its cord is
loose. This may cause fire or electric shock.
Do not touch any electrical parts such as the power supply plug or any switches with a wet hand.
This may cause electric shock.
Check the setting when resuming the operation after power failure or switch off. The stocked
materials may be affected if the setting is changed.
Do not put a container with water or heavy articles on the unit. It may cause injury if the articles
fall. Current leakage or electric shock may result form deterioration of insulation by spilled water.
Do not climb onto the unit and do not put articles on the unit. This may cause injury by tipping or
0
damage to the unit.
Never touch the inside chamber, door glass, exhaust vent or inside of the door when the unit is
operating with high temperature setting as it may cause burn.
Ml Hold the handle when closing the door. This will reduce the likelihood of a trapped finger.
Never place your hand on the glass or use excessive force on the glass. Intentional force may
break the glass resulting in injury from the broken glass.
0
Do not lean on the door. This may cause injury, current leakage, or electric shock if the unit tips over
or door becomes detached.
Disconnect the power supply plug before moving the unit. Take care not to damage the power cord.
A damaged cord may cause electric shock or fire.
• В Be careful not to tip over the unit during movement to prevent damage or injury.
^^ Disconnect the power plug when the unit is not used for long periods.
( \ ) Do not put the packing plastic bag within reach of children as suffocation may result.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS FOR USAGE
1. This unit is not explode-proof construction. Never store the materials which cause flammable or volatile
gas and never store the flammable or volatile liquid in the unit.
2. The door glass, inside door panel, and exhaust vent are very hot when the unit is used with high
temperature setting. Never touch such portion directly with the hands.
3. Avoid to open the door when the chamber temperature is more than 100°C as it is dangerous. The
door opening may cause ignition of flammable material or break of equipment resulting from sudden
temperature change.
4. Do not block the air intake vent on the chamber floor by the stocked articles. The blockage can cause
unstable chamber temperature and shorten the heater life.
5. When cleaning, do not use brushes, acids, benzine, thinner, soap, cleaner or hot water. These will
cause discoloring or damage to coated surfaces.
On plastic or rubber parts, they will cause
transformation, discoloration or degeneration. Never apply volatile chemicals (like benzine etc.) on plastic
or rubber parts. When neutral detergent is used, be sure to wipe it up thoroughly with a wet cloth
afterwards. Before cleaning the box, refer to page 18.
6. When placing objects inside, remove traces of water as much as possible.
7. When stacking the unit, always use stacking kit available as an optional component.
ENVIRONMENTAL CONDITIONS
This equipment is designed to be safe under the following conditions (based on the IEC 1010-1):
1.Indoor use;
2. Altitude up to 2000 m;
3. Ambient temperature 5°C to 35°C
4. Maximum relative humidity 80% for temperature up to 31 °C decreasing linearly to 50% relative humidity
at 40°C;
5. Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage;
6. Other supply voltage fluctuations as stated by the manufacturer;
7. Transient overvoltages according to Installation Categories (Overvoltage Categories) II; For mains
supply the minimum and normal category is II;
8. Pollution degree 2 in accordance with IEC 664.
Download from Www.Somanuals.com. All Manuals Search And Download.
STERILIZER COMPONENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
STERILIZER COMPONENTS
1. Door: During use, inner panel of the door becomes extremely hot; Be careful.
2. Observation window: During use, glass and its surrounding become very hot; Be careful.
3. Leveling foot: Made of rubber. Can be adjusted by screws.
4. Fan (inside): Propeller type. To cool down the heat discharge plate and fan motor.
5. Control panel: Refer to page 9.
6. Separation plate: Do not place objects directly on the plate. Especially if the holes are covered, the
proper temperature cannot be obtained.
7. Heater box (inside): The heater is attached under separation plate. The sirocco fan is also attached
in this box.
8. Packing: Be careful not to scratch.
9. Key lock switch: Put the switch to "OFF" when you set the operating condition. After the setting, put
the switch to "ON" to prevent the set condition from changing by accidental contact.
10. Main power switch with circuit breaker: Main switch for all power. When the operation of the unit
is stopped by this circuit breaker, contact with a dealer or a service station after disconnected the power
supply plug.
11. Exhaust air vents: The air inside the oven is exhausted from these vents. Be careful not to block
these vents.
12. Handle: Pull the knob of inside of the handle to open the door.
13. Rack support: This can be adjusted to change the height.
14. Rack: They can be slid forward.
15. Exhaust air vent: The exhaust is controlled by opening/closing the vent. During use, the
temperature of this section is extremely high; Be careful.
16. Temperature sensor (installation position): Be careful not to allow objects to touch the sensor or
scratch it.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
STERILIZER COMPONENTS
Control panel and keypad
1
2
3
4
5
6
7
8
1. Power switch (POWER): Power switch of the control panel.
2. Alarm buzzer stop key (BZ): Press this key to silence the buzzer in the event that the alarm operates
and the buzzer sounds. Press it once again to reactive the buzzer.
3. Timer mode select key (TIMER MODE): By pressing this key, the timer mode is selected. Refer to
the "Timer function" on page 13.
4. Digit shift key ( • • ) : Pressing this key in the setting mode causes the changeable digit to shift.
5. Numerical value shift key (^ ): Pressing this key in the setting mode causes the numerical value to
shift.
6. Call key (CALL): By pressing this key, the unit enters the setting mode, and the digits that can be set
flash, except that only set value display mode is available when unit is running.
7. Delay timer key (DELAY): Pressing this key results in delayed starting of running.
8. Run/Stop key (RUN/STOP): This key is for start/stop the running.
9. Digital temperature/timer indicator (TEMP/TIME): This indicator shows the temperature or the time.
10. Delay timer lamp: This lamp lights when the delay timer is active.
11. Start lamp: This lamp lights when the unit is running.
12. Alarm lamp: This lamp lights when the unit is warning condition.
13. Set value lamp: This lamp lights when setting mode or set value display mode as the unit is running.
14. Timer mode 1 lamp: This lamp lights when timer mode 1 is active.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Installation site
To operate this unit properly and to obtain maximum performance, install the unit in a location with the
following conditions:
1. A location not subjected to direct sunlight or direct air flow from an air conditioner
2. A location with adequate ventilation
Leave at least 30 cm around the unit for ventilation. Poor ventilation will result in a reduction of the
performance.
3. A location away from heat generating sources
Avoid installing the unit near heat-emitting appliances such as gas ranges or stoves.
4. A location with a sturdy and level floor
WARNING
Install the unit on a sturdy floor. If the floor is not strong enough or the installation site is not adequate,
this may result in injury from the unit falling or tipping over.
Select a level and sturdy floor for installation. This precaution will prevent the unit from tipping.
Improper installation may result in water spillage or injury from the unit tipping over.
5. A location without flammable or corrosive gas
WARNING
Never install the unit in a flammable or volatile location. This may cause explosion or fire.
Never install the unit where acid or corrosive gases are present as current leakage or electric shock
may result due to corrosion.
6. A location not prone to high humidity
WARNING
Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to rain
water.
Never install the unit in a humid place or a place where it is likely to be splashed by water.
Deterioration of the insulation may result which could cause current leakage or electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
INSTALLATION
Installation
1. Remove the packaging materials and tapes
Remove all transportation packaging materials and tapes. Open the doors and ventilate the unit. If the
outside panels are dirty, clean them with a neutral detergent and wipe it up with a wet cloth.
2. Adjust the leveling feet
Extend the leveling legs by rotating them counterclockwise so they contact the floor or bench. Ensure the
unit is level.
3. Ground (earth)
WARNING
Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet is
not grounded, it is necessary to install a ground by qualified engineers.
Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such
grounding may cause electric shock in the case of an incomplete circuit.
BEFORE COMMENCING OPERATION
Prerunning
When using the unit for the first time after purchasing, operate the unit without objects inside.
1. Install the racks in the chamber.
2. Set the temperature at 200°C and operate the unit for 20 minutes.
3. Leave the unit as it is until the chamber temperature is cool enough.
4. Ventilate the room when opening the chamber door as the smoke with a strong odor is exhausted.
5. Keep the chamber door opened for a while until the odor is eliminated.
Note:
Some odor may be remained after prerunning. Such residue is eliminated gradually during usage.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Basic operating flow chart of control panel
1. Start of operation when the input of setting is conducted.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
OPERATING INSTRUCTIONS
Timer function
The timer function has two modes as follows:
1. Normal mode: starts immediately after start of the running
2. Timer mode 1: starts when the chamber temperature is 2.0°C lower than the set point.
When conducting the sterilization, always select "Timer mode 1".
On timer mode 1, the timer starts when the chamber temperature is 2.0°C lower than the set point. After
timer starting, the temperature indicator blinks, alarm lamp lights, and intermittent tone sounds if the
chamber temperature is 5.0°C or more lower than set point due to the door opening, etc.
In spite of the alarm condition, the unit continues to run. The timer is reset to initial setting when the
chamber temperature is 2.0°C lower than the set point again.
Set point
Start
Normal mode
Timer mode 1
(For sterilization)
Sterilization
Refer to the table below when setting the sterilization temperature and duration.
Sterilization temperature
135to145°C
Sterilization duration
3 to 5 hours
160to170°C
2 to 4 hours
180to200°C
0.5 to 1 hour
In case of sterilizing a lot of samples, extend the sterilization time for more than an hour.
• When sterilizing the combustibles, such as cotton capped tube and instrument which are covered with
paper, do not put them on the shelves directly. Use the wire basket and upper shelves instead.
• When sterilizing the pipettes or the glass pipes, waterdrop must be dried out clearly, otherwise
sterilization will not be completed.
• Take out the articles in the chamber when the chamber temperature is lower than 50°C.
Note:
Do not open the door during sterilization.
Do not open the door when the chamber temperature is higher than 100°C.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Stable running
Table below shows the basic procedure for setting the chamber temperature. Perform key operations in
the sequence indicated in the table. The example in the table is based on the assumption that the desired
temperature is 50°C and continuous running.
50°C
Time
Basic operation sequence (Example: Chamber temperature; 50 C, Continuous running)
Indication after operation
Key operated
Description of operation
О
О
DELAY
START
О ALARM
О
0
SET VALUE
MODE
d Ь
1
2
3
1
Press the power key.
POWER
(The current chamber temperature is displayed.)
0
•
ALARM
•
DELAY
START
SET VALUE
О
(Delay time reset)
DELAY
0 0
0 0
О MODE 1
Press the delay timer key.
(The fourth digit of the indicator flashes.)
О ALARM
•
О
DELAY
START
•
SET VALUE
Press the delay timer key to reset
the delay time.
DELAY
DELAY
О MODE 1
0 0
E5
0 0
О
О
DELAY
START
О ALARM
SET VALUE
Press the delay timer key and the
current chamber temp, is displayed.
О
4
О MODE 1
О
О
DELAY
START
О ALARM
•
SET VALUE
(Temperature set)
Press the call key.
к
0
CALL
(The third digit of the indicator 1lashes.)
О ALARM
О
О
DELAY
START
Set the temp, to 050 with the digit
shift key and the numeric value
shift key.
•
0
SET VALUE
MODE
6
7
8
1
5 0
0
О ALARM
О
О
DELAY
START
(Time set)
•
0
SET VALUE
MODE
a
о 0 U
CALL
1
Press the call key.
(The fourth digit of the indicator flashes.)
О ALARM
О
О
DELAY
START
Set the time to --:- with the digit
shift key and numeric value shift
key.
•
SET VALUE
—
0 MODE
1
_
-I
- -
0
0
ALARM
SET VALUE
О
•
DELAY
RUN
(Start running)
START
с
E
STOP
О MODE 1
9
Press the run/stop key.
(The unit runs.)
Note:
When the delay time is not set, operation 2, 3, and 4 is not necessary.
-:— of the indicator is displayed by the numerical value shift key at fourth digit flashing.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Stable running with delay time
50°C
Delay time
Basic operation sequence (Example: Chamber temperature; 50°C, Delay time; 1 hour)
Description of operation
Key operated
Indication after operation
О ALARM
О SET VALUE
О MODE 1
О
О
DELAY
START
POWER
E5\
Press the power key.
(The current chamber temperature is displayed.)
О ALARM
•
DELAY
(Delay time reset)
• SET VALUE
О MODE 1
О
START
DELAY
00 00
Press the delay timer key.
(The fourth digit of the indicator flashes.)
Set the time to 01:00 with the digit
shift key and the numeric value
shift key.
О ALARM
•
О
DELAY
START
•
SET VALUE
••
О MODE 1
0 / 00
E\5
О ALARM
О SET VALUE
О
О
DELAY
START
Press the delay timer key and the
current chamber temp, is displayed.
DELAY
CALL
О MODE
1
О ALARM
SET VALUE
О MODE
О
О
DELAY
START
(Temperature set)
Press the call key.
•
0 DO
1
(The third digit of the indicator flashes.)
О ALARM
О
О
DELAY
START
Set the temp, to 050 with the digit
shift key and the numeric value
shift key.
•
SET VALUE
••
О MODE
1
0 5 0
О ALARM
SET VALUE
О MODE 1
О DELAY
START
(Time set)
•
О
0 0 DO
CALL
Press the call key.
(The fourth digit of the indicator flashes.)
О ALARM
О DELAY
Set the time to --:-- with the digit
shift key and numeric value shift
key.
•
SET VALUE
О
START
О MODE
1
••
О ALARM
О SET VALUE
° MODE 1
•
•
DELAY
START
(Start running)
RUN
m
STOP
Press the run/stop key.
(The unit runs.)
Start of operation with no change of setting
Key operated
Indication after operation
Description of operation
О ALARM
О SET VALUE
О MODE 1
О
О
DELAY
START
00 00
Press the power key.
POWER
(The current chamber temp, is displayed.)
О ALARM
• SET VALUE
О
О
DELAY
START
/ BID
Press the call key
CALL
°
MODE
1
(The third digit of the indicator flashes.)
О ALARM
SET VALUE « S T A R T
О MODE 1
О DELAY
RUN
О
5
E
Press the run/stop key.
STOP
(The unit runs.)
Download from Www.Somanuals.com. All Manuals Search And Download.
-IK
OPERATING INSTRUCTIONS
Sterilization with timer mode 1
200°C
2 hours
lours)
Basic operation sequence (Example: Chamber temperature; 180°C, Delay time; 2 I
Key operated
Indication after operation
Description of operation
0 ALARM
SET VALUE
О MODE
О
О
DELAY
START
i
1
iE151
0
Press the power key.
1
POWER
(The current chamber temperature is displayed.)
О ALARM
SET VALUE
0 MODE
•
О
DELAY
START
'
-
~В В ВD
•
(Release of delay set time)
Press the delay timer key.
DELAY
1
2
3
4
(The fourth digit of the indicator flashes.)
О ALARM
• SET VALUE
•
О
DELAY
START
Press the delay timer key to reset
the delay time.
DELAY
DELAY
0 В В 0
О MODE
1
0 ALARM
О SET VALUE
О
О
DELAY
START
Press the delay timer key and the
current chamber temp, is displayed.
E 5
0 MODE
1
0 ALARM
• SET VALUE
О DELAY
.
> В' *-, В D
О
START
(Temperature set)
Press the call key.
CALL
lashes.)
(The third digit of the indicator i
О ALARM
О
О
DELAY
START
1
Set the temp, to 180 with the digit
shift key and the numeric value
shift key.
• SET VALUE
О MODE 1
6
7
••
В п
t
О ALARM
• SET VALUE
О
О
DELAY
START
(Time set)
1
В
0 В
CALL
Press the call key.
(The fourth digit of the indicator flashes.)
0 ALARM
О
0
DELAY
START
Set the time to 02:00 with the digit
shift key and numeric value shift
key.
•
•
SET VALUE
MODE
8
9
••
1
в E 0
t
В
(Timer mode 1 set)
TIMER
MODE
0 В
E В
Press the timer mode select key.
(The timer mode 1 lamp is ighted.)
О ALARM
О SET VALUE
MODE
О
•
DELAY
START
RUN
1
0
(Start of operation)
q
E _7
STOP
•
1
Press the run/stop key.
(The unit runs.)
Download from Www.Somanuals.com. All Manuals Search And Download.
ALARMS & SAFETY FUNCTIONS
This unit has the alarms and safety functions shown in table below, and also self diagnostic functions.
Alarms and safety functions
Alarm &
Buzzer
Safety operation
Indication
Situation
Safety
If the internal temperature
deviates from the set
temperature by +10°C or more
(and if timer mode 1, by -5°C or
more)
Automatic set
temperature
Alarm
Alarm lamp lights.
All digits on the
indicator flash.
—
Intermittent tone
If a key operation is not
performed for about 45 sec. in
each setting mode.
The setting mode
is cancelled.
—
—
Auto return
Normal display mode.
Key input is
disabled.
When the key lock switch is
turned ON.
Key lock switch
Temperature
sensor
abnormality
Alarm lamp lights.
E01 is displayed on
the indicator.
If the temperature sensor goes
open circuit.
Intermittent tone Heater OFF
Alarm lamp lights.
E02 is displayed on
the indicator.
Intermittent tone
Heater OFF
If the triac goes open circuit.
If the triac goes short circuit.
If the relay goes short circuit.
Triac
abnormality
Alarm lamp lights.
E03 is displayed on
the indicator.
Intermittent tone Heater OFF
Alarm lamp lights.
E04 is displayed on
the indicator.
Heater OFF
Intermittent tone
Relay
If the relay goes open circuit or
fan motor and heater goes short
circuit. Or the ambient temp,
of circuit is 65°C or more.
(when unit is not running)
The security circuit is activated
by independent temp, sensor if
the chamber is abnormal over-
heating.
abnormality
Alarm lamp lights.
E05 is displayed on
the indicator.
Intermittent tone Heater OFF
Heater OFF
Without display
change.
forcedly by
Continuous tone
external circuit.
Independent
over-heat
protection
(When unit is running)
Continuous tone
(When the temp,
s decreased,
Alarm lamp lights.
E05 is displayed on
the indicator.
Heater OFF
forcedly by
external circuit.
The security circuit is activated
by independent temp, sensor if
the chamber is abnormal over-
heating.
ntermittent tone)
* The buzzer tone resulting from the independent over-heat protection cannot be stopped with the BUZZER
key. Turn off the main switch.
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTINE MAINTENANCE
LWARNING
Always disconnect the power supply to the unit prior to any repair or maintenance of the unit in
order to prevent electric shock or injury.
Ensure you do not inhale or consume medication or aerosols from around the unit at the time of
maintenance. These may be harmful to your health.
CAUTION
Always put on dry gloves to protect hands at the time of maintenance. Failure to use gloves may
result in cuts or abrasions from any sharp edges or corners.
Note:
Never attempt to directly spray water on the heater box or the inside of the oven as it is very dangerous.
In addition, never use volatile or combustible chemicals to clean the inside.
Cleaning of unit
Cleaning the inside
• Remove all racks from the inside.
• Clean the inside using a soft cloth damped with neutral detergent. Afterwards, wipe off with a cloth
washed in clean water.
• Remove the separation plate at the bottom of the oven and wipe off any particles in the heater box, using
a soft cloth damped with water.
•
Cleaning the frame
• Clean the frame using a soft cloth damped with neutral detergent. Afterwards, wipe it up the detergent
with a wet cloth.
Cleaning the rack
• To clean the rack, place it in a tub of warm water mixed with neutral detergent and wipe with a sponge or
a soft cloth. Racks subject to high temperature will naturally become colored. This is a natural
coloration, acknowledge this.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
TROUBLE SHOOTING
If the unit malfunctions, check out the following before calling for service.
The unit does not operate at all
1. The unit is not plugged correctly into a power outlet.
2. The circuit breaker at the power source is active.
3. A power failure has occurred.
4. A fuse has blown.
The key operation is disabled
1. The key lock function is set in OFF mode.
If the alarm function operates
If the alarm function and the buzzer operates, check the cause using the following procedure.
[At the beginning of operation]
1. The chamber temperature is not equal to the set value.
[During operation]
1. The set temperature value was changed.
2. The door was left open for a long period.
3. A low temperature load was placed inside the unit.
In these case, if the unit is left as it is, the alarm will eventually clear itself.
If the chamber temperature is not equal to the set temperature
1. The temperature in the vicinity is too high.
The ambient temperature must always be at least 5°C less than the set temperature.
2. The unit is installed tilted.
DISPOSAL OF UNIT
AWARNING
If the unit is to be stored unused in an unsupervised area for an extended period ensure that children do
not have access and doors cannot be closed completely.
The disposal of the unit should be undertaken by appropriate personnel. Always remove doors to
prevent accidents such as suffocation.
Download from Www.Somanuals.com. All Manuals Search And Download.
1Q
SPECIFICATIONS
Sterilizer
Name
Model
MOV-112S
MOV-212S
W730 x D645 x H870 (mm)
W600 x D500x H500 (mm)
150 L
External dimensions
Internal dimensions
Effective capacity
Exterior
W580 x D595 x H820 (mm)
W450 x D450x H450 (mm)
90 L
Electrically galvanized steel plate, Acrylic resin painted
Stainless steel plate (SUS 304)
Electrically galvanized steel plate, Acrylic resin painted
Reinforced glass x 3, W150 x H380 mm
Glass wool
Interior
Door
Observation window
Insulation
Rack
Stainless steel plate, Stainless wire (SUS 304)
Sensor K, PID control
Temperature controller
Temperature display
Timer
Digital display
Electronic timer with delay timer
15A
Circuit breaker
Overheat prevention
mechanism
Built-in thermister (electric circuit), Thermal guard
Heater
1.1 kW
1.2 kW
Fan motor
Accessories
Weight
Output 10 W
2 racks, 4 rack supports
50 kg
3 racks, 6 rack supports
66 kg
Note: Design or specifications will be subject to change without notice.
PERFORMANCE
Model
MOV-112S
MOV-212S
Usable environment condition
Extent chamber temperature
Temperature control range
Temperature; 0°C to 35°C
Ambient temperature +5°C to 200°C
±4°C
Time of reaching maximum
Temperature (0°C -» 200°C)
60 minutes
70 minutes
AC110V 60Hz, 1030W
AC115to120V 60Hz, 1130W
AC220 50/60Hz, 1130W
AC110 to 120V 60Hz, 1230W
AC220V 50/60HZ, 1230W
AC230 to 240V 50Hz, 1230W
Power source, Rated power consumption
AC230 to 240V 50Hz, 1130W
Note: The unit with CE mark complies with EC directives 89/336/EEC, 93/68/EEC and 73/23/EEC.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Please fill in this form before servicing.
Hand over this form to the service engineer to keep for his and your safety.
Safety check sheet
1. Refrigerator contents :
•Yes
•Yes
•Yes
•Yes
• No
• No
• No
• No
Risk of infection:
Risk of toxicity:
Risk from radioactive sources:
(List all potentially hazardous materials that have been stored in this unit.)
Notes :
2. Contamination of the unit
Unit interior
•Yes
•Yes
•Yes
•Yes
• No
• No
• No
• No
No contamination
Decontaminated
Contaminated
Others:
3. Instructions for safe repair/maintenance of the unit
a) The unit is safe to work on
DYes
DYes
DNo
DNo
b) There is some danger (see below)
Procedure to be adhered to in order to reduce safety risk indicated in b) below.
Date :
Signature :
Address, Division :
Telephone :
Serial number:
Date of Installation :
Product name :
Sterilizer
Model :
MOV-112S, MOV-212S
Please decontaminate the unit yourself before calling the service engineer.
Download from Www.Somanuals.com. All Manuals Search And Download.
91
|