OPERATOR'S MANUAL
HAMMER DRILL
18 VOLT
HD1800M
2
0
5
Your new hammer drill has been engineered and manufactured to Ryobi's high standard for dependability, ease of
operation, and operator safety. When properly cared for, the hammer drill will give you years of rugged, trouble-free
performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
pack into a tool that has the switch on, invites
accidents.
WARNING:
I
I
I
I
Remove adjusting keys or wrenches before
turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in
personal injury.
Read and understand all instructions. Failure to
follow all instructions listed below, may result in elec-
tric shock, fire and/or serious personal injury.
Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enables better control of the tool in unexpected
situations.
SAVE THESE INSTRUCTIONS
WORK AREA
I
Keep your work area clean and well lit. Cluttered
Use safety equipment. Always wear eye protec-
tion. Dust mask, non-skid safety shoes, hard hat, or
hearing protection must be used for appropriate
conditions.
benches and dark areas invite accidents.
I
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools may create
sparks which may ignite the dust or fumes.
Do not use on a ladder or unstable support.
I
Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
TOOL USE AND CARE
I
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Hold-
ing the work by hand or against your body is unstable
and may lead to loss of control.
ELECTRICAL SAFETY
I
A battery operated tool with integral batteries or
a separate battery pack must be recharged only
with the specified charger for the battery. A
charger that may be suitable for one type of battery
may create a risk of fire when used with another
battery.
I
I
I
Do not force tool. Use the correct tool for your ap-
plication. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is dan-
gerous and must be repaired.
Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or stor-
ing the tool. Such preventive safety measures reduce
risk of starting the tool accidentally.
I
I
I
Use battery operated tool only with specifically
designated battery pack. Use of any other
batteries may create a risk of fire. Use only with
battery pack listed.
Avoid body contact with grounded surfaces,
such as pipes, radiators, ranges, and
refrigerators. There is an increased risk of electric
shock if your body is grounded.
I
I
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Use battery only with charger listed.
BATTERY PACK
1322401/1323303
CHARGER
1423701
PERSONAL SAFETY
I
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
I
I
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cut-
ting edges are less likely to bind and are easier to con-
trol.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the
tool serviced before using. Many accidents are
caused by poorly maintained tools.
I
I
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in
moving parts.
Avoid accidental starting. Be sure switch is off
before inserting the battery pack. Carrying tools
with your finger on the switch or inserting the battery
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
I
I
Use only accessories that are recommended by
SERVICE
the manufacturer for your model. Accessories that
may be suitable for one tool, may create a risk of in-
jury when used on another tool.
I
Tool service must be performed only by qualified
repair personnel. Service or maintenance per-
formed by unqualified personnel could result in a risk
of injury.
Keep the tool and its handle dry, clean, and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean your
I
When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Mainte-
nance section of this manual. Use of unauthorized
parts or failure to follow Maintenance Instructions
may create a risk of shock or injury.
tool.
SPECIFIC SAFETY RULES
I Hold tool by insulated gripping surfaces when performing an operation where the tool may contact hidden
wiring. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
I
I
Do not charge cordless tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
Forbestresults,yourcordlesstoolshouldbecharged
in a location where the temperature is more than
50°F but less than 100°F. Do not store outside or in
vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in con-
tact with your skin, wash immediately with soap
and water, then neutralize with lemon juice or
vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
ADDITIONAL SAFETY RULES
I
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations,
as well as the specific potential hazards related
to this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
I
Always wear safety goggles or safety glasses
with side shields when operating this product.
Failure to do so could result in dust, shavings, or
loose particles being thrown into your eyes, resulting
in possible serious injury.
I
I
I
Protect your lungs. Wear a face mask or dust
mask if the operation is dusty.
Protect your hearing. Wear hearing protection
during extended periods of operation.
ADDITIONAL CORDLESS TOOL RULES
I
Cordless tools do not have to be plugged into an
electrical outlet; therefore, they are always in oper-
atingcondition.Beawareofpossiblehazardswhen
not using your cordless tool or when changing
accessories. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
I
I
I
Do not place cordless tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
Adamagedbatteryissubjecttoexplosion.Toavoid
seriouspersonalinjury,properlydisposeofadamaged
battery.
Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pilot
light. To reduce the risk of serious personal injury,
neveruseanycordlessproductinthepresenceofopen
flame. An exploded battery can propel debris and
chemical. If exposed, flush with water immediately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
I
Do not operate charger with a damaged cord or
CHARGER RULES
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce
theriskofelectricshock,fire,orseriouspersonalinjury.
I
Before using battery charger, read all instructions
and cautionary markings in this manual, on bat-
tery charger, and product using battery charger.
Followingthisrulewillreducetheriskofelectricshock,
fire, or serious personal injury.
I
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
I
To reduce risk of injury, charge only nickel-cad-
mium type rechargeable batteries. Other types of
batteries may burst causing personal injury and
damage. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
I
I
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrectreassemblymayresultinariskofelectric
shock or fire. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
I
I
I
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious per-
sonal injury.
Toreducetheriskofelectricshock,unplugcharger
from outlet before attempting any maintenance or
cleaning. Turning off controls will not reduce this
risk. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a
risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
I
I
I
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious per-
sonal injury.
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
I
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting charger. Following this rule will re-
duce the risk of electric shock, fire, or serious personal
injury.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them these
instructions also. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
I
I
Make sure cord is located so that it will not be
steppedon,trippedover,orotherwisesubjectedto
damage or stress. Following this rule will reduce the
risk of serious personal injury.
WARNING:
Do not abuse the cord. Never carry the charger by
the cord or yank it to disconnect it from the recep-
tacle. Keep the cord from heat, oil, and sharp
edges. Followingthisrulewillreducetheriskofelectric
shock or fire.
Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
I
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
a. That pins on plug of extension cord are the same
number,sizeandshapeasthoseofplugoncharger.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating
of charger as specified below:
Cord Length (Feet) 25'
Cord Size (AWG) 16
50'
16
100'
16
Note: AWG = American Wire Gage
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Hertz
Current
Hz
Frequency (cycles per second)
W
Watt
Power
Time
min
Minutes
Direct Current
Type of current
Type of current
Alternating Current
n
No Load Speed
Rotational speed, at no load
0
.../min
Per Minute
Safety Alert
Revolutions, strokes, surface speed, orbits etc. per minute
Precautions that involve your safety
Eye Protection
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
Wet Conditions Alert
Do not expose to rain or use in damp locations.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
SYMBOL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices that may cause property damage.
Important: Advises you of important information or instructions vital to the operation or maintenance of
the equipment.
Note: Advises you of additional information concerning the operation or maintenance of the equipment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
HAMMER DRILL
Chuck ...................................................................................................................................................................... 1/2 in.
Maximum Torque ...............................................................................................................................................350 in.lbs
Switch....................................................................................................................................................... Variable Speed
Clutch .............................................................................................................................................................24 positions
Motor ................................................................................................................................................................18 Volt DC
Hammer Speed ..................................................................................... Low (0 - 5,200 BPM*) & High (0 - 18,200 BPM*)
No Load Speed .................................................................................................. Low (0 - 400/min) & High (0 - 1400/min)
CHARGER ASSEMBLY
Charger Input ........................................................................................................................... 120 Volts, 60 Hz, AC only
Charger Voltage ..................................................................................................................................................... 18 Volt
Charge Rate........................................................................................................................................................... 1 Hour
* Blows Per Minute
UNPACKING
INSTRUCTIONS
Yourhammerdrillhasbeenshippedcompletelyassembled.
PACKING LIST
Hammer Drill with Auxiliary Handle Assembly
Battery Pack (2)
I Carefully remove the tool and accessories from the
box.
Charger
I Make sure that all items listed in the packing list are
Carrying Case
included.
Operator’s Manual
I Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
WARNING:
I Do not discard the packing material until you have
If any parts are missing do not operate your tool until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
carefully inspected and satisfactorily operated the tool.
I If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
WARNING:
The hammer drill should never be connected to a
power supply when you are assembling parts, making
adjustments, cleaning, performing maintenance, or
when the tool is not in use. Disconnecting the tool will
prevent accidental starting that could cause serious
injury.
APPLICATIONS
You may use the hammer drill for the purposes listed below:
I Hammer drilling in concrete, brick, or other masonry.
I Drilling in wood.
I Drilling in ceramics, plastics, fiberglass, and laminates.
I Drilling in both soft and hard metals.
I Driving screws with screwdriver bits, using driving accessories.
I Mixing paint.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Before using the hammer drill, familiarize yourself with all
operating features and safety requirements. However, do
not let familiarity with the tool make you careless.
ADJUSTABLE TORQUE CLUTCH
The hammer drill is equipped with an adjustable torque
clutch for driving different types of screws into different
materials.
WARNING:
Exercise caution when using the hammer drill. Care-
less actions, for even a fraction of a second, can result
in serious personal injury.
DEPTH GAUGE ROD
A depth gauge rod is installed on the auxiliary handle
assembly to assist you in controlling the depth of drilled
holes.
Your new hammer drill is equipped with the following
features. See Figure 1.
AUXILIARY HANDLE ASSEMBLY
An auxiliary handle is installed on the hammer drill. For
ease of operation, you may use the handle with either the
left hand or the right hand.
SWITCH
Your hammer drill has a conveniently located trigger
switch.
LEVEL DRILLING
TWO-SPEED GEAR TRAIN
Two levels are recessed in the motor housing of the
hammer drill. One is located on top, while the other is
located on the end. They can be used to keep drill bits level
during both horizontal and vertical drilling operations.
The hammer drill has a two-speed gear train designed for
drilling or driving at LO (1) or HI (2) speeds. A slide switch
is located on top of the drill to select either LO (1) or HI (2)
speed. When using the drill in the LO (1) speed range, the
speed decreases and the tool has more power and torque.
When using the drill in the HI (2) speed range, the speed
increases and the tool has less power and torque. Use LO
(1)speedforhighpowerandtorqueapplicationsandHI(2)
speed for fast drilling or driving applications.
BIT STORAGE
When not in use, you can place the bits provided with your
hammer drill in the storage area located on the top of the
drill.
MAG TRAY™
For convenience, your hammer drill has a Mag Tray™ to
place small parts when doing a variety of tasks.
REVERSIBLE
Thishammerdrillallowsyoutoreversethebitrotation.You
can control the direction with the lever located on the top
of the tool.
ERGONOMIC DESIGN
The design of the hammer drill provides for easy handling.
Itisdesignedforcomfortandeaseofgraspwhenoperating
in different positions and at different angles.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
END VIEW OF LEVEL FOR
VERTICAL DRILLING
TOP VIEW OF LEVEL FOR
HORIZONTAL DRILLING
LEVEL
LEVEL
TWO SPEED
GEAR TRAIN (HI-LO)
WING SCREW
AUXILIARY
HANDLE
BIT
STORAGE
AREA
DEPTH
GAGE ROD
5
DIRECTION OF
ROTATION SELECTOR
(FORWARD/REVERSE)
KEYLESS CHUCK
MODE SELECTOR TORQUE
ADJUSTMENT RING
TRIGGER
SWITCH
MAG TRAY™
(SCREW HOLDER)
BATTERY
PACK
Fig. 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
TO
TIGHTEN
KNOB
WARNING:
The hammer drill should never be connected to a
power supply when you are assembling parts, making
adjustments, cleaning, performing maintenance, or
when the tool is not in use. Disconnecting the tool will
prevent accidental starting that could cause serious
injury.
TO
LOOSEN
ADJUSTING THE AUXILIARY HANDLE
ASSEMBLY
See Figure 2.
Followthesestepstoadjusttheauxiliaryhandleassembly.
I
I
I
Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
AUXILIARY
HANDLE
ASSEMBLY
Rotate the auxiliary handle assembly to the desired
location.
Fig. 2
Tighten the auxiliary handle assembly securely by
turning the knob clockwise.
KNOB
ADJUSTING THE DEPTH GAUGE ROD
See Figure 3.
DEPTH GAUGE
ROD
Follow these steps to adjust the depth gauge rod.
I
I
I
Lock the trigger switch by placing the rotation
selector in the center position.
DRILL BIT
8
Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
5
Adjust the depth gauge rod so that the drill bit
extends beyond the end of the rod to the required
drilling depth.
I
Tighten the auxiliary handle assembly by turning the
knob clockwise.
TO INCREASE
DRILLING DEPTH
ADJUSTING THE SPEED
TO DECREASE
DRILLING DEPTH
AUXILIARY
HANDLE
See Figure 4.
The hammer drill has a two-speed gear train that provides
a high speed of approximately 1,400/min and a low speed
of approximately 400/min (stated speeds are with the
trigger switch in the “Full-on” position).
ASSEMBLY
DRILLING
DEPTH
Fig. 3
Follow these steps to adjust the speed.
TWO-SPEED
GEAR TRAIN (HI-LO)
I
For high speed: Slide the two-speed gear train switch
LO
SPEED
to “2.”
I
For low speed: Slide the two-speed gear train switch
to “1.”
1
2
HI
SPEED
Note: If you have difficulty changing from one gear
range to the other, turn the chuck by hand until the
gears engage.
2
0
CAUTION:
5
Never change gears while the tool is running. Failure
to obey this caution could result in serious damage to
the drill.
Fig. 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
ADJUSTING THE TORQUE
See Figure 5.
HAMMER MODE
DRILLING MODE
The hammer drill is equipped with an adjustable torque
clutch for driving different types of screws into different
materials.Adjustthetorqueasnecessary.Werecommend
that you use carbide-tipped bits and select hammer mode
when drilling in hard materials such as brick, tile, concrete,
etc.
TO DECREASE
TORQUE
Follow these steps to adjust the torque.
I
Identify the torque indicator settings located on the
front of the hammer drill.
I
Rotate the adjusting ring to the desired setting.
•
•
•
1 - 4
5 - 8
9 - 12
For driving small screws.
For driving screws into soft material.
TORQUE
TO INCREASE
TORQUE
ADJUSTING RING
For driving screws into soft and hard
materials.
Fig. 5
•
•
•
•
13 - 16 For driving screws in hard wood.
17 - 20 For driving large screws.
FORWARD / REVERSE
REVERSE
SELECTOR
21 -
For heavy drilling.
For hammer drilling.
2 4
CHANGING THE BIT ROTATION
See Figure 6.
The direction of the chuck is controlled by the rotation
selector located above the trigger switch.
5
Follow these steps to change the bit rotation.
I
For forward rotation: Move the rotation selector to the
left.
I
For reverse rotation: Move the rotation selector to the
right.
FORWARD
CENTER POSITION
(LOCK)
Fig. 6
Note: The hammer drill will not run unless the
selector is pushed fully to the left or right.
CAUTION:
The hammer drill is not designed for reverse hammer-
ing. Failure to obey this caution may result in property
damage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
INSERTING BITS
See Figure 7.
UNLOCK
(Release)
DRILL BIT
Follow these steps to insert bits.
I
Lock the trigger switch by placing the rotation
selector in the center position.
I
Position the chuck jaws so that the opening is
slightly larger than the drill bit you intend to use.
Note: To open the chuck jaws, turn the chuck
sleeve counterclockwise. To close the chuck jaws,
turn the chuck sleeve clockwise.
2 0
CHUCK JAWS
I
Raise the front of the drill to keep the drill bit from
falling out of the chuck jaws.
LOCK
(Tighten)
CHUCK SLEEVE
WARNING:
Fig. 7
RIGHT
Do not insert a drill bit into the chuck jaws and tighten
as shown in Figure 8. This could cause the drill bit to
be thrown from the drill resulting possible serious in-
jury or damage to the chuck.
I
Insert the drill bit completely into the chuck.
I
Tighten the chuck jaws securely on the drill bit using
the chuck key provided. Do not use a wrench to
tighten or loosen the chuck jaws.
REMOVING BITS
See Figure 7.
5
Follow these steps to remove bits.
I
I
I
Lock the trigger switch by placing the rotation
selector in the center position.
WRONG
Loosen the chuck jaws using the chuck key pro-
vided.
Fig. 8
Remove the drill bit from the chuck jaws.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Do not place charger in an area of extreme heat or cold.
It will work best at normal room temperature.
WARNING:
Table 1
Always wear safety goggles or safety glasses with side
shields when operating this tool. Failure to do so could
result in dust, shavings, or loose particles being thrown
into your eyes, resulting in possible serious injury.
COLOR
STATUS
Red
Fast Charging Mode
Fully Charged
Control Charge or
Green
Yellow and Green
Defective Battery Pack
WARNING:
RECHARGING HOT BATTERIES
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame.
An exploded battery can propel debris and chemicals.
If exposed, flush with water immediately.
When using your hammer drill continuously, the batteries
in your battery pack become hot. You should let a hot
battery pack cool down for approximately 30 minutes
before attempting to recharge.
Note: This situation occurs when continuous use of your
hammer drill causes the batteries to become hot. It does
not occur under normal circumstances. Refer to
CHARGING BATTERIES for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack
and charger/charging assembly to your nearest Ryobi
Authorized Service Center for electrical check.
CHARGING BATTERIES
See Figures 9 and 10.
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it prior to use.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (cutting followed by
recharging) for them to fully charge.
BATTERY
CHARGER
GREEN LIGHT "ON"
INDICATES FULLY
CHARGED
Follow these directions when charging batteries.
I Charge battery pack only with the charger provided.
I Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
I Connect charger to power supply.
I Place battery pack in charger. Align raised rib on
battery pack with groove in charger.
I Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
When properly connected, red light will turn on. When
your battery pack becomes fully charged, the red light
will turn off and the green light will turn on.
RED LIGHT "ON"
INDICATES FAST
CHARGING MODE
YELLOW AND GREEN LIGHTS "ON"
INDICATES CONTROL CHARGE OR
DEFECTIVE BATTERY PACK
Note: Normally, the yellow and green lights on the charger
will come on. This indicates charger is in control charge
mode and should switch to fast charge mode within 5
minutes. When charger is in fast charge mode the red light
will come on. If after a period of 15 minutes the yellow and
green lights remain on, remove the battery pack, wait 1
minute and reinsert battery pack in charger. If the yellow
and green lights continue to remain on an additional 15
minutes, the battery pack is damaged and will not accept
charge. See Table 1.
Fig. 9
BATTERY
CHARGER
After normal usage, 1 hour of charge time is required to be
fully charged. A minimum charge time of 1 to 1-1/2 hours
is required to recharge a completely discharged tool.
BATTERY
PACK
The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
Fig. 10
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
INSTALLING THE BATTERY PACK
See Figure 11.
Follow these steps to install the battery pack.
I Lock the trigger switch by placing the rotation
selector in the center position.
I Place the battery pack on the tool.
I Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
on the tool before beginning operation.
CAUTION:
BATTERY PACK
When placing the battery pack on the tool, make sure
that the raised rib inside the tool aligns with the groove
on the battery pack and that the latches snap into
place properly. Improper assembly of the battery pack
can cause damage to internal components.
LATCHES
REMOVING THE BATTERY PACK
See Figure 11.
Follow these steps to remove the battery pack.
I Lock the trigger switch by placing the rotation
selector in the center position.
DEPRESS LATCHES TO
RELEASE BATTERY PACK
I Depress the latches on the side of battery pack.
Fig. 11
I Remove the battery pack from the tool.
TURNING ON/OFF THE HAMMER DRILL
See Figure 12.
Follow these steps to turn on/off the hammer drill.
I Turn on the hammer drill: Depress the trigger switch.
I Turn off the hammer drill: Release the trigger switch.
2 4
5
TO TURN ON
Fig. 12
TO TURN OFF
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
USING THE LEVELS
See Figure 13.
Two levels are recessed in the motor housing of the
hammer drill. One is located on top, while the other is
located on the end. They can be used to keep drill bits
TOP VIEW
level during both horizontal and vertical drilling operations.
DRILLING
See Figure 13.
20
LEVEL
Follow these steps to drill.
I Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
I Hold the tool firmly and place the bit at the point to
be drilled.
I Depress the trigger switch to start the tool.
I Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
or apply side pressure to elongate a hole.
WARNING:
Be prepared for binding or breakthrough. When these
situations occur, the drill has a tendency to grab and
kick in the opposite direction and could cause loss of
control when breaking through material. If you are not
prepared, this loss of control could result in possible
serious injury.
LEVEL
HELPFUL TIPS
I When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This prevents
the drill bit from slipping off center as you start the
hole. You may, however, start holes without center
punching if you use the lower speed. To accomplish
this action, simply operate the drill at a lower speed
until the hole is started.
END VIEW
I When drilling metals, use a light oil on the drill to keep
it from overheating. The oil will prolong the life of the
bit and increase the drilling action.
0 2
1 5
I If the bit jams in the workpiece or if the drill stalls, stop
the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
WARNING:
Do not force the tool. Forcing the tool can result in
jamming and loss of balance or footing, which could
result in personal injury.
Fig. 13
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
BATTERY DISPOSAL
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
To preserve natural resources, please recycle or dispose
of the battery properly. Local, state, or federal laws may
prohibit disposal of Nickel-Cadmium batteries in
ordinary trash.
Consultyourlocalwasteauthorityforinformationregarding
available recycling and/or disposal options.
WARNING:
For more information on battery recycling call
1-800-8BATTERY.
The hammer drill should never be connected to a
power supply when you are assembling parts, making
adjustments, cleaning, performing maintenance, or
when the tool is not in use. Disconnecting the tool will
prevent accidental starting that could cause serious
injury.
Y
C
C
E
R R B R C
1
™
7
.
N i C d
8
83
0
0
8
.
.
8
2
2
GENERAL
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
WARNING:
Do not attempt to disassemble the battery pack. Fire or
injury can result.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline, petro-
leum-based products, penetrating oils, etc. come in
contact with plastic parts. They contain chemicals that
can damage, weaken, or destroy plastic.
Upon removal, cover the battery pack's terminals with
heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its compo-
nents. Also, never touch both terminals with metal
objects and/or body parts, as short circuit can result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
BATTERIES
Your tool is equipped with Nickel-Cadmium rechargeable
batteries.Lengthofservicefromeachchargingwilldepend
on the type of work you are doing.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. DO NOT disassemble battery
pack and attempt to replace the batteries. Handling of
thesebatteries,especiallywhenwearingringsandjewelry,
could result in serious burn.
To obtain the longest possible battery life, we suggest the
following:
I Storing or charging the batteries in temperatures
above 100º F or below 50º F will shorten battery life.
I Never store batteries in a discharged condition. Wait
for battery to cool and charge immediately.
I All batteries gradually lose their charge. The higher
the temperature, the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REMOVING THE CHUCK
See Figures 14, 15, and 16.
MALLET
Follow these steps to remove the chuck.
CHUCK JAWS
I Lock the trigger switch by placing the rotation selec-
tor in the center position.
I Insert a 5/16 inch or larger hex key wrench into the
2
0
chuck of the drill and tighten the chuck jaws securely.
5
I Tap the hex key wrench sharply with a mallet in a
clockwise direction. This will loosen the screw in the
chuck for easy removal.
I Open the chuck jaws and remove the hex key
wrench.
KEYLESS
CHUCK
HEX KEY
I Remove the chuck screw by turning it in a clockwise
Fig. 14
direction.
Note: The screw has left-handed threads.
I Insert the hex key wrench in the chuck and tighten
the chuck jaws securely.
SCREWDRIVER
I Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. It can
now be unscrewed by hand.
5
TIGHTENING THE CHUCK
See Figures 14 and 15.
The chuck may become loose on the spindle and begin to
shake when using the drill. Also, the chuck screw may
become loose causing the chuck jaws to bind and prevent
them from closing.
Fig. 15
Follow these steps to tighten the chuck.
I Lock the trigger switch by placing the rotation selec-
tor in center position.
I Open the chuck jaws.
I Insert the hex key wrench into the chuck and tighten
the chuck jaws securely.
I Tap the hex key wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle.
2
0
I Open the chuck jaws and remove the hex key
wrench.
5
I Tighten the chuck screw.
Note: The chuck screw has left-handed threads.
Fig. 16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
HAMMER DRILL
18 VOLT
HD1800M
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest Ryobi authorized service center. Be sure to provide all relevant
information when you call or visit. For the location of the authorized service center nearest you, please call
The model number of this tool is found on a plate attached to the motor housing. Please record the serial
number in the space provided below. When ordering repair parts, always give the following information:
HD1800M
Model No.
Serial No.
RYOBI TECHNOLOGIES INC.
1428 Pearman Dairy Road
Post Office Box 1207
Anderson, SC 29625
Anderson, SC 29622
1-800-525-2579
983000-196
3-03
Download from Www.Somanuals.com. All Manuals Search And Download.
|