Samsung Network Card RIF BT10 User Guide

Bluetooth user manual  
(RIF-BT10)  
Table of Contents  
1. Hardware, & Software ------------------------------------------------------------------ 2  
2. Specifications  
----------------------------------------------------------------- 3  
----------------------------------------------------------------- 4  
----------------------------------------------------------------- 5  
3. System Structure  
4. How to configure  
Attachment 1. Virtual serial port driver installation  
Attachment 2. Virtual serial port setting  
Attachment 3. Dip switch setting  
Attachment 4. Bluetooth slave setting  
Attachment 5. Bluetooth master setting  
Attachment 6. Printer driver installation & Test page printing  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Specifications  
Category  
Specification  
RIF-BTM10  
Model name  
Connection System  
Interface Port  
POS System  
(Printer : SRP-350, SRP-270)  
USB(PC), RS-232C(PC), UART(Printer)  
Hardware(RTS/CTS)  
Flow control  
Transmission speed (bps)  
Power  
19200,9600  
DC 5V/150mA  
(USB port or RS-232C Pin 9 or Printer power)  
Bluetooth Specification  
Service Distance  
V1.0B  
&
V1.1  
Max 100 m (Class 1)  
Network Support  
(Master: Slave)  
Multi-Connection Support = N:7(max N=infinity)  
Simultaneous printing = 1 : n (max. n=7)  
SPP(Serial Port Profile) &  
Printing Profile Support  
Dimensions(W x L x H)  
HCRP(Hardcopy Cable Replacement Profile)  
70 x 45 x 11 mm  
Rx Buffer: 1024 byte  
Tx Buffer: 512 byte  
Rx/Tx Buffer  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. System structure  
Connect Bluetooth master module to the USB port (or Serial) of PC and Bluetooth slave module to the  
printers.  
1) A network between PC (Master) and Printers (Slave) is n : n. The number of PC can be infinite on  
network while printers can be max up to 7.  
2) Master can designate the printer for use after finding all the printers installed around.  
(Refer to Application programmer’s guide for developing Bluetooth application program)  
3) Master can save Bluetooth address of the printers up to 7 and then no need to search for printers  
4) Master can send data to max 7 printers at the same time.  
5) Bluetooth compatible module like PDA also can use the printer.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. How to configure  
1) Virtual serial port driver installation (required only when you use the USB port on the PC)  
- Connect Bluetooth main (master) to USB port of PC (Refer to Attachment 3. Dip switch setting)  
- Found New Hardware Wizard detects new hardware by Plug and Play and select Include this  
location in the search. Then select the folder which contains VirtualCOM_R9032148.  
- When installation completes, Found New Hardware Wizard will detects new hardware once again.  
Then repeat the above setting one more time.  
- Refer to Attachment 1.Virtual serial port driver installation.  
2) Virtual serial port driver setting (required only when you use the USB port on the PC)  
- Check Virtual port and apply the setting as below.  
- Start > Control Panel > System > Hardware > Device Manager  
- Select USB Serial Port under Port (COM x: Port number varies from your PC condition) and change  
the Properties.  
- Port Setting: 19200, 8, none, 1, hardware  
- Advanced Setting: 4096, 4096, 16, 0, 0,  
Check in “Serial Enumerator” and “Serial Printer” .  
(In case of Win 98, You cannot see “miscellaneous option” Just ignore)  
- Make sure not to change COM Port Number (When changes, select the open port)  
- Refer to Attachment 2. Virtual serial port setting  
3) Bluetooth & Printer dip switch setting  
- Set Maser/Slave, Baud rate and handshaking by Dip switch.  
- 19200 bps, DTR/DSR (RTS/CTS) (Be sure that communication condition must be all the same for  
PC, Bluetooth master, Bluetooth slave, Printer)  
- Refer to Attachment 3. Dip switch setting  
4) Bluetooth slave setting  
- Connect Bluetooth main (master/slave) to USB (or Serial) port of PC.  
- Execute BluetoothConfig_V2.x.exe from the downloaded files.  
- Select the virtual port  
a) USB port: Select the virtual port (COM x) of step 2).  
b) Serial (RS-232C): Select the COM x connected.  
- Configure Adapter setting: slave, 19200, hardware  
- Disconnect the Bluetooth main (master/slave) from the PC, assemble it with the Cover_BT, and  
connect it to the printer.  
- Refer to Attachment 4. Bluetooth slave Setting  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
5) Bluetooth master setting  
- Connect Bluetooth main (master/slave) to USB (or Serial) port of PC.  
- Execute BluetoothConfig_V2.x.exe from the downloaded files.  
- Select the port  
a) USB port: Select the virtual port (COM x) of step 2).  
b) Serial (RS-232C): Select the COM x connected.  
- Configure Adapter setting: master, 19200, hardware  
- Register Printer setting: Search the printers around and save the printer address by  
button “Search”. Make sure the printers are all power on mode.  
- Configure Adapter setting: Check in auto connector to printers.  
- Click “ok”.  
- Refer to Attachment 5. Bluetooth master Setting  
6) Printer driver installation & Test page printing  
- Once the setting’s complete, disconnect the Bluetooth master from the PC, reconnect it and initialize  
the system. Turn the printer off and then on to initialize the Bluetooth slave.  
- Wait for approximately 20 seconds for the Bluetooth master and slave are automatically  
reconnected.  
- Install the printer driver (Available at website)  
a) SRP 350: V3.0.5E above  
b) SRP 270: V3.0.3E above  
- You can download the printer driver from the homepage. Make sure that you delete the older version  
driver from the PC before you install the new one(Clean register)  
- Open the printer driver and select a port  
a) USB port: Select the virtual port (COM x) of step 2).  
b) Serial (RS-232C): Select the COM x connected.  
- Set the port settings as below (19200, 8, none, 1, hardware)  
- Test Page Printing.  
- Refer to Attachment 6. Test page printing  
7) Other  
- If you are a POS Application Programmer, refer to the manual below for more information.  
: “Bluetooth control message V1.x  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attachment 1. “Virtual serial port driver installation”  
1. Connect Bluetooth Master to USB port of PC.  
2. Then Found New Hardware will show up and pop up Found New Hardware Wizard. Then select  
Installation from a list specific location (Advanced).  
3. Select the right location of VirtualCOM_R9032148 by “Browse” and go to “Next”.  
4. Found New Hardware (USB Serial Port) will show up again when installation completes. Then install the  
same file again as same as above steps.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attachment 2. Virtual serial port setting  
1. Open Device Manager as the below path:  
: Start > Control Panel > System > Hardware > Device Manager  
2. Select “USB Serial Port (COM x)” that is installed newly. Go to “Properties” by right button of mouse.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Select the conditions as below at “Port Settings” and click “Advanced”  
4. Set as below and apply “OK”  
(Note: Windows 98 dose not have “Serial Enumerator” or “Serial Printer” under “Miscellaneous Option.”)  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attachment 3. “Dip switch setting”  
1. Bluetooth  
Function  
USB Master  
Serial Master  
Slaver  
SW1-1  
SW1-2  
OFF  
ON  
SW1-3  
OFF  
SW1-4  
OFF  
OFF  
ON  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
Firmware  
download  
OFF  
OFF  
OFF  
ON  
2. Printer Baud rate (bps) and Handshaking setting (Default 19200 bps)  
Model  
Baud rate(bps)  
SW1-7  
Off  
Hand shaking  
bps  
19200  
9600  
4800  
2400  
bps  
SW1-8  
Off  
DTR/DSR  
SRP-350  
On  
Off  
(SW1-3 off)  
Off  
On  
On  
On  
SW2-7  
Off  
SW2-8  
Off  
9600  
4800  
2400  
19200  
bps  
DTR/DSR  
SRP-270  
SRP-370  
SRP-500  
On  
Off  
(SW2-3 off)  
Off  
On  
On  
On  
SW1-1  
On  
SW1-2  
On  
115200  
38400  
19200  
9600  
bps  
DTR/DSR  
Off  
On  
(SW1-3 off)  
On  
Off  
Off  
Off  
SW2-7  
On  
SW2-8  
Off  
19200  
9600  
4800  
2400  
DTR/DSR  
Off  
Off  
(SW2-3 on)  
Off  
On  
On  
On  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attachment 4. Bluetooth slave setting  
1. Connect the Bluetooth main (Master/Slave) to the USB (or Serial) port on the PC.  
2. Execute BluetoothConfig_V2.x.exe”  
3. Select the port  
a) USB port: Select the virtual port (COM x) of step 2).  
b) Serial (RS-232C): Select the COM x connected.  
4. Select the same port as you chosen at Virtual COM and click “Configure Adapter”.  
5. Set as below and apply OK. (slave, 19200, hardware)  
6. Disconnect the Bluetooth main (Master/Slave) from the PC, assemble it with the Cover_BT, and connect it  
to the printer.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attachment 5. Bluetooth master setting  
1. Connect the Bluetooth main (Master/Slave) to the USB (or Serial) port on the PC.  
2. Execute BluetoothConfig_V2.x.exe”  
3. Select the port  
a) USB port: Select the virtual port (COM x) of step 2).  
b) Serial (RS-232C): Select the COM x connected.  
4. Select the same port as you chosen at Virtual COM and click “Configure Adapter”.  
5. Set as below and apply OK. (master, 19200, hardware)  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Select “Register Printers”  
7. Select “Search” (The printer should be Power ON)  
8. All Bluetooth Interface found will appear with address automatically. Just apply OK for saving in Bluetooth  
master.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Click “Close” .  
10. Select “Configure Adapter” and check “auto connect to printers”  
11. Click “OK” and then “Quit” to exit.  
12. Disconnect the Bluetooth main (Master/Slave) from the PC.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The below terms explains each item reading at Configure adapter  
1) Bluetooth address  
- Individual address of each Bluetooth module.  
2) Firmware version  
- Bluetooth firmware version.  
3) Role  
- Selection of Master/Slave.  
4) Baud rate  
- Transmission speed setting.  
5) Flow control  
- Handshaking condition setting.  
6) Auto connect to printers  
- Auto connection to the designated Bluetooth slave.  
- Applicable when the designated printer (Bluetooth slave) used.  
- When the multiple printers installed, simultaneous printing becomes available.  
- It ignores the printer in Power off mode.  
- The data transmission stands by when any of the registered printers goes on Busy mode such  
as no paper, cover open, buffer full etc until it recovers.  
- With no use of this option, Application program should send data only after it connected to  
Bluetooth slave by Control message. This can be used when wanted to use the designated  
one out of several printers  
7) Wait for all connected  
- It is available only when Auto connect to printers selected.  
- Under the condition of several Bluetooth slave saved in Bluetooth master, it transmits the data  
thoroughly until the all the registered printers complete the reception.  
8) Printer name  
- You can set the printer name less than 15 letters.  
9) Auto detect  
- It is to read the individual printer name such as SRP-350 etc.  
- It is available only when the printer has the individual name.  
10) Printer location  
- It is to set the location identity of the printer such as Kitchen PRT 1 or Receipt PRT 1 less  
than 12 letters.  
11) Print F/W info  
- Printer prints the firmware data of Bluetooth slave module at printer power on.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attachment 6. Printer driver installation & Test page printing  
1. Once the setting’s complete, disconnect the Bluetooth master from the PC, reconnect it and initialize the  
system. Turn the printer off and then on to initialize the Bluetooth slave.  
2. Wait for approximately 20 seconds for the Bluetooth master and slave are automatically reconnected.  
3. Install the printer driver (Available at website)  
a) SRP 350: V3.0.5E above  
b) SRP 270: V3.0.3E above  
4. Open the printer driver and select a port  
a) USB port: Select the virtual port (COM x) of step 2).  
b) Serial (RS-232C): Select the COM x connected.  
5. Select the port and Click “Apply”.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Set the port settings as below (19200, 8, none, 1, hardware)  
7. Click “OK” and then “Close”.  
8. Open the printer drive again and click “Test Page Print”.  
9. The windows test page prints.  
V1.00  
WWW.SAMSUNGMINIPRINTERS.COM  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Home Security System 49 351 User Guide
RCA Cassette Player BLV552 User Guide
RCA Cassette Player SCT 530 User Guide
Rheem Water Heater RMTG2 53PVNPVPXNXP User Guide
Rolls Games GS76R User Guide
Roper Refrigerator RS22AQXM User Guide
Runco Computer Monitor CW 42i User Guide
Ryobi Trimmer RY28120 User Guide
Sangean Electronics Stereo System SR 2 User Guide
Sanus Systems Clock VMCA9 User Guide