|
USER MANUAL
4 CHANNELS NETWORK
DIGITAL VIDEO RECORDER
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Cautions
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of insinuated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instruction in the
literature accompanying the product.
USERS OF THE SYSTEM ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL
FEDERAL, STATE, AND LOCAL LAWS AND STATUTES CONCERNING THE MONITORING AND
RECORDING OF VIDEO AND AUDIO SIGNALS. ULTRAK SHALL NOT BE HELD RESPONSIBLE
FOR THE USE OF THIS SYSTEM IN VIOLATION OF CURRENT LAWS AND STATUTES.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION ------------------------------------------------------------------------------------------
1
1
2
4
4
4
5
5
6
6
7
8
8
9
9
9
9
FEATURE ----------------------------------------------------------------------------------------------------------
CHAPTER 2 HARDWARE OVERVIEW ------------------------------------------------------------------------------
CHAPTER 3 SETUP PROCEDURES ---------------------------------------------------------------------------------
1. MAIN MENU SETUP -----------------------------------------------------------------------------------------
2. SYSTEM SETUP ---------------------------------------------------------------------------------------------
3. CAMERA SETUP ---------------------------------------------------------------------------------------------
4. RECORD SETUP ---------------------------------------------------------------------------------------------
5. SCHDULED RECORD --------------------------------------------------------------------------------------
6. EVENT LIST ----------------------------------------------------------------------------------------------------
7. HDD MANAGEMENT ----------------------------------------------------------------------------------------
8. LOAD DEFAULT ----------------------------------------------------------------------------------------------
9. EXIT --------------------------------------------------------------------------------------------------------------
CHARPTER 4 OPERATION PROCEDURES -----------------------------------------------------------------------
1. GETTING STARTED WITH YOUR MACHINE --------------------------------------------------------
2. RECORDING --------------------------------------------------------------------------------------------------
3. PLAYBACK -----------------------------------------------------------------------------------------------------
4. HARD DISK and CF Card RECOMMEND ------------------------------------------------------------- 10
5. BACKUP -------------------------------------------------------------------------------------------------------- 11
6. ALARM CONTROL ------------------------------------------------------------------------------------------- 12
7. EXTERNAL ALARM CONNECTOR ---------------------------------------------------------------------- 12
8. NETWORK ----------------------------------------------------------------------------------------------------- 13
SPECIFICATIONS ------------------------------------------------------------------------------------------------- 13
CHAPTER 5 RECORDING TIME LENGTH ------------------------------------------------------------------------- 14
CHAPTER 6 HARD DRIVE INSTALLATION PROCEDURES -------------------------------------------------- 15
V1.02 2004/11/04
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU List
SYSTEM SETUP
BUZZER DURATION
VIDEO LOSSALARM
HDD PASSW ORD
SET TIME/DATE
EXIT
3SEC
ON
SETUP MENU
SYSTEM SETUP
CAMERA SETUP
RECORD SETUP
SCHEDULE RECORD
EVENT LIST
CAMERA SETUP
CAMERA SELECT
CAMERA RECORD
M OTION DETECTION
M OTION SENSITIVITY
CH1
ON
ON
5
BRIGHTNESS
CONTRAST
HUE
STANDARD
STANDARD
STANDARD
EXIT
HDD MANAGEMENT
LOAD DEFAULT
EXIT
RECORD SETUP
RECORD MODE
NORMAL RECORD FPS
ALARM RECORD FPS
ALARM REXORD DW ELL 5SEC
RECORD QUALITY HIGH
M OTION EVENT MIGRATION OFF
EXIT
MUX
15P
15P
SCHEDULE RECORD
ˇ
O O O O O O O O O O O O O O O O O -
： ： ： ： ： ：
0 3 6 9 12 15 18 21 24
PRESS[UP，DOW N] TO SELECT
PRESS[ENTER] TO SET，[MENU] TO EXIT
EVENT LIST
MASTER HARD DRIVE
> 01 2003/AUG/25 12:13:16 REC
02 2003/AUG/25 11:14:21 PW R
03 2003/AUG/25 11:14:00 MOT CH3
04 2003/AUG/25 09:35:24 ALM CH1
HDD MANAGEMENT
OVERW RITE MODE
HDD FULL W ARNING
NO
10%
M ASTER HDD CAPACITY 239GB
M ASETR HDD LEFT RATIO 209GB 88%
M ASTER HDD FORMAT
SLAVE HDD CAPACITY
SLAVE HDD LEFT RATIO
SLAVE HDD FORMAT
EXIT
N/A
N/A
v
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INTRODUCTION
This product is 4 cameras input appliance with multiple function which will bring you following features:
z
Device can be performed as VHS system with live display, play back and video recording。
z
Device operates in hardware base with no OS (operating system) necessary for more reliability and
stability。
z
Digitize data storage with M-JPEG compression technology will give you organized video data
management without using mess huge traditional video tape。
z
z
Support various type of camera with real, live mode display。
Multi-speed recording selection on normal recording mode or alarm recording mode, the highest
speed of recording is 30/25 (NTSC/PAL) fields on both mode。
z
z
z
Contrast, hue and brightness are adjustable for each camera individually。
Support up to 2 hard disks (HDD) from 40GB to 250GB compatible。
When external alarm is triggered , correspond cameras number will show up on the monitor with
texts。
z
z
z
z
z
Selectable recording qualities (best/high/medium/low)。
Recording can operate manually or gets activated automatically when alarm is triggered。
Motion detection function available, user can easily adjust sensitive of motion detection。
Playback record can be searched by time or by event list。
Play back mode could not be easier then ever for you to review the video that gets recorded on
reverse (x6) and fast forwarding (×2, ×4, ×6)。
z
z
z
z
z
z
z
z
z
z
Play back mode with pause (field by field) for forward。
Easy operation, setting can be easily modified OSD (on screen display) menu。
Device will overwrites data and notice operator on monitor when the HDD is going full。
HDD capacity status can be display on the screen for better storage management。
System will restore the previous setting and continue camera activity after restart。
Key lock function available to secure your DVR from button pressing accidentally。
Provide 2 Monitor output。
Optional network function
Support compact flash (CF) card for random backup and VCR for fully backup。
Alarm notification could be sent via email when motion or external alarms are triggered.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
Hardware Overview
Front Panel Layout Overview
5
6
7
8
9
10 11 12 13 14 15 16
17
22
23
1
2
3
4
19 18 20 21
Buttons Function List
Function
Part
Label
1
2
3
4
POWER
REC
Power status LED.
Recording status LED.
Playback status LED.
H.D.D LED
PLAY
H.D.D
1.
2.
This View button controls FULL SCREEN display from camera 1.
A password can be setup by the view control button for number 1.
5
6
1
1.
2.
This View button controls FULL SCREEN display from camera 2.
A password can be setup by the view control button for number 2.
2
3
1.
2.
This View button controls FULL SCREEN display from camera 3.
A password can be setup by the view control button for number 3.
7
1.
2.
This View button controls FULL SCREEN display from camera 4.
A password can be setup by the view control button for number 4.
8
4
9
Quad screen: All cameras are displayed.
Press REC to start recording.
Quad
10
REC
11
12
6 times speed fast rewind mode.
Rew Search
STOP
Press Stop to stop playback or recording.
Press Pause to pause (field by field) for forward.
You can easily lock your DVR by press 5 times Pause button under
recording or monitoring mode. When key lock is activated, you can see a
“L” show up on your upper right corner of screen. Press 5 times again to
release your button from key lock mode.
13
Pause
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Press F. Fwd to play video forward at high speed. Press the button again
the speed will be change circulative from ×2,×4, , to the highest ×6.
14
F.Fwd Search
15
16
Press the Play button to into time search and play video forward.
Press MENU to go into or exit menu.
PLAY
MENU
1. Move the cursor upward or decrease the number.
17
▲
2. When it’s not under recording mode, you can use the button to adjust
position of date & time display which appears on OSD.
1. Move the cursor downward or increase the number.
2. When it’s not under recording mode, you can use the button to adjust
position of date & time display which appears on OSD
18
19
20
▼
1. Press ENTER button to make choose or make confirm in MENU
◄ ( ENTER)
► ( ENTER)
system.
2. You can use ENTER key to indicates H.D.D status when system is not
under Menu mode.
3. Make any changes in the selected option or decrease/increase the
number.
21
22
23
COPY
CF Card
CF Card Backup button.
Slot for compact flash (CF) card.
Location of installation for removable HDD.
HDD FRAME
Back Panel Layout Overview
29
27
26
25
24
28
30
31
Back Panel Components Function List
Function
Part
24
25
26
27
28
29
30
Label
ETHERNET
Ethernet network interface.
LED
Network power indicator and network activate indicator.
COM port for RS-485 interfaces which upon to request.
Camera 1-4 video output with BNC connector.
Camera 1-4 video input with BNC connector.
COM PORT
CAMERA OUT
CAMERA IN
MONITOR OUT
ALARM IN / Relay
Composite video output with 2 BNC connectors.
8-Pin Alarm input and Relay output connector.
AC90V~AC260V input.
Power ON/OFF switcher.
31
POWER / POWER SW
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
SETUP PROCEDURES
1. MAIN MENU SETUP
SETUP MENU
Press the MENU button to go into the main menu.
Use the ▲ or ▼ button to select items.
> SYSTEM SETUP
CAMERA SETUP
RECORD SETUP
SCHEDULE RECORD
EVENT LIST
Press the ◄ or ► button to confirm the selection.
Press MENU to escape to exit the set up mode.
HDD MANAGEMENT
LOAD DEFAULT
EXIT
Contents:
c
d
3
4
g
h
i
j
SYSTEM SETUP
System set up
CAMERA SETUP
Camera set up
RECORD SETUP
Recording set up
SCHEDULE RECORD
Schedule Recording set up
EVENT LIST
Event indexing
HDD MANAGEMENT
Hard disk management
LOAD DEFAULT
Return to factory setting
EXIT
Escape from the setup menu
2. SYSTEM SETUP
SYSTEM SETUP
Press the MENU button to go into the main menu.
Use the ▲ or ▼ button to select items.
>
BUZZER DURATION
VIDEO LOSS ALARM
3SEC
ON
Press the ◄ or ► button to confirm the selection.
Press MENU to escape to exit the set up mode.
HDD PASSWORD
SET TIME/DATE
EXIT
Contents:
c
d
e
BUZZER DURATION 3SEC (1-30)
Use ◄ or ► button to adjust the duration time of the buzzer action.
VIDEO LOSS ALARM
On for default
HDD PASSWARD
A password can be setup to protect the hard disk content. It needs to be entered in order
to perform a hard disk format. Initial number is 1111.
Use the view control button on the front panel to input the number.
is “1” ,
is “2” ,
is “3” ,
is “4”
f
g
SET TIME/DATE
Use the ◄ or ► button to select items.
Press the ▲ or ▼ button to increase / decrease the number.
EXIT
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Exit from the SYSTEM SETUP menu
3. CAMERA SETUP
CAMERA SETUP
Press the MENU button to go into the main menu.
Use the ▲ or ▼ button to select items.
> CAMERA SELECT
CAMERA RECORD
MOTION DETECTION ON
MOTION SENSITIVITY
BRIGHTNESS
CONTRAST
HUE
CH1
ON
Press the ◄ or ► button to confirm the selection.
Press MENU to escape to exit the set up mode.
5
STANDARD
STANDARD
STANDARD
EXIT
Contents:
c
2
3
4
CAMERA SELECT
Use ◄ or ► button to select the camera from CAM 1 – CAM 4 to be adjusted.
CAMERA RECORD ON(ON/OFF)
Use ◄ or ► button to select ON/OFF recording.
MOTION DETECTION ON(ON/OFF)
CH1(CH1~CH4)
Use ◄ or ► button to select ON/OFF motion detection.
MOTION SENSITIVITY(1~10)
Use ◄ or ► button to adjust sensitivity of motion detection for selected camera. Initial
number from 1 to 10, default value is 5(STANDARD).
BRIGHTNESS STANDARD(1~10)
Use ◄ or ► button to adjust the brightness of the selected camera. Initial number is 5
(STANDARD).
CONTRAST STANDARD(1~10)
Use ◄ or ► button to adjust the contrast of the selected camera. Initial number is 5
(STANDARD).
HUE STANDARD(1~10)
Use ◄ or ► button to adjust the hue of the selected camera. Initial number is 5
(STANDARD).
EXIT
5
6
7
8
Exit from the CAMERA SETUP menu
4. RECORD SETUP
RECORD SETUP
Press the MENU button to go into the main
menu.
Use the ▲ or ▼ button to select items.
> RECORD MODE
MUX
15P
15P
5SEC
HIGH
NORMAL RECORD FPS
ALARM RECORD FPS
ALARM RECORD DWELL
RECORD QUALITY
Press the ◄ or ► button to confirm the
selection.
Press MENU to escape to exit the set up mode.
MOTION ENENT MIGRATION OFF
EXIT
Contents:
c
RECORD MODE
MUX(MUX/QUAD)
Use ◄ or ► button to select MUX or QUAD recording.
d
NORMAL RECORD FPS 15P (1~5P/7P/10P/15P/30P)
Use ◄ or ► button to select recording speed.
15P means 15 fields per second, 30P is the highest speed, and 1P is the lowest. There are
a total of nine speeds you can choose from. (FPS: Field per second)
Note: PAL: (1~4P/6P/8P/12P/25P) NTSC=15P, PAL=12P on default.
ALARM RECORD FPS 15P (1~5P/7P/10P/15P/30P)
e
Use ◄ or ► button to select alarm recording speed when external alarm or motion
5
Download from Www.Somanuals.com. All Manuals Search And Download.
detection is triggered.
Note: PAL: (1~4P/6P/8P/12P/25P) NTSC=15P, PAL=12P on default.
ALARM RECORD DWELL 5SEC (1-30)
f
g
Use ◄ or ► button to set the dwell time for alarm recording when external alarm or motion
detection is triggered.
When external alarm is triggered and within the dwell period:
-
-
the screen will be switched into 4 format.
The corresponding camera will be marked ID “EXT”
RECORD QUALITY HIGH(BEST/HIGH/MEDIUM/LOW)
Use ◄ or ► button to select the BEST, HIGH, MEDIUM or LOW setting so there is a total
of four levels of recording quality that can be chosen from. The higher the quality, the
higher the amount of storage will be consumed. Thus, this setting should be carefully
chosen as it will affect the usage of hard disk storage.
A table of relationship between quality, record speed and hard disks is attached for
Reference.
h
i
MOTION EVENT MIGRATION OFF
You can decide to include or exclude motion events by turning on or turning off in this
option. The default setting is off.
EXIT
Exit from the RECORD SETUP menu
5. SCHEDULE RECORD
SCHEDULE RECORD
Press the MENU button to go into the
main menu.
ˇ
O O O O O O O O O O O O O O O O O O O O O O O O
Use the ◄ or ► button to select items.
：
0
：
3
：
6
：
：
：
： ：
18 21
：
24
9
12
15
Press the ▲ or ▼ button to confirm the
selection.
PRESS (UP,DOWN) TO SELECT
PRESS (ENTER) TO SET, (MENU) TO EXIT
Press MENU to escape to exit the set
up mode.
Contents:
1
SCHEDULE RECORD
There are 24 circles in the schedule table, which represent 24 hours.
Every circles has 3 options to select:
O : represents “fully record”
X : represents “no record”
A : represents “alarm record”
Use the ◄ or ►button to select items.
Press ▲ or ▼ button to select the O/ X / A (Fully / No / Alarm Record).
6. EVENT LIST
Press ◄ or ► key on “EVENT LIST” than windows will appear as below:
EVENT LIST
MASTER HARD DRIVE
>
01 2004/JUN/25 12:13:16 REC
02 2004/JUN/25 11:14:21 PWR
03 2004/JUN/25 10:03:04 REC
04 2004/JUN/25 09:35:24 ALM CH1
Use “▲ or ▼“ key to select event which needs to be played，location of “ > “ symbol will move up
6
Download from Www.Somanuals.com. All Manuals Search And Download.
and down for indicating current event which been selected.
Press “◄ or ►” key to select events storage from master hard drive or slave hard drive . When once
selection has been made and than press ►PLAY key to start playing records in normal speed.
There are totally 4 different type’s event will be recorded:
1. REC：Event when start recording by press “REC” key.
2. PWR：System will event up from power interruption after restarting.
3. ALM：When external alarm was triggered, event up with alarm number.
4. MOT：When motion detection was triggered, event up with alarm number. Record setup
“MOTION EVENT MIGRATION” must setting on.
7. HDD MANAGEMENT
HDD MANAGEMENT
Press the MENU button to go into the
main menu.
> OVERWRITE MODE
HDD FULL WARNING
MASTER HDD CAPACITY
MASTER HDD LEFT RATIO
MASTER HDD FORMAT
SLAVE HDD CAPACITY
SLAVE HDD LEFT RATIO
SLAVE HDD FORMAT
EXIT
NO
20%
76GB
73GB 97%
Use the ▲ or ▼ button to select items.
Press the “◄ or ►” button to confirm
the selection.
N/A
N/A
Press MENU to escape to exit the set
up mode.
Contents:
1
OVERWRITE MODE YES (NO)
Use “◄ or ►” button to enable or disable overwriting when HDD is full.
When HDD overwrite is enabled, the oldest partition on the HDD will automatically be
reused, that means the oldest images will be overwritten by the current images.
When overwrite mode is disabled, the HDD Full Warning percentage selection will be
appeared and need to be configured.
d
e
HDD FULL WARNING 10% (5% / 10% / 15% / 20%)
Use “◄ or ►” button to select one of the four settings (5% / 10% / 15% / 20%).
The default is 10%. The buzzer will turn on when free space left in the HDD go below the
set value and it will on again when the total free space left go below 5%.
MASTER HDD CAPACITY
The master HDD capacity sign will be indicated in left on the screen, It can’t be revised.
MASTER HDD LEFT RATIO 73GB 97%
76GB
f
g
The master HDD left ratio sign will be indicated in left on the screen, It can’t be revised.
MASTER HDD FORMAT
Use “◄ or ►” button to enter the MASTER HDD FORMAT menu.
PASSWORD INPUT (4) : _ _ _ _
Use the view control button on the front panel to input the number.
is “1” ,
is “2” ,
is “3” ,
is “4”
When you key in the correct password, the screen will be displayed the following
message:
PASSWORD CORRECT!
HARD DISK FORMATTED
Otherwise, the following error message will be displayed on the screen:
PASSWORD INCORRECT!
7
Download from Www.Somanuals.com. All Manuals Search And Download.
h
SLAVE HDD CAPACITY
N/A
The slave HDD capacity sign will be indicated in left on the screen, It can’t be revised.
HDD N/A is with no HDD.
7
SLAVE HDD LEFT RATIO
N/A
The slave HDD left ratio sign will be indicated in left on the screen, It can’t be revised.
HDD N/A is with no HDD.
SLAVE HDD FORMAT
Same with MASTER HDD FORMAT.
EXIT
8
9
Escape from the HDD MANAGEMENT menu.
8. LOAD DEFAULT
Use the “◄ or ►” button to return to the factory default. This will clear all the user settings and
replace it with the original default parameters (The HDD Password and Schedule Record can’t be
defaulted here).
9. EXIT
Exit from the SETUP MENU.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
OPERATION PROCEDURES
1
Getting Started with your machine
Please assure the following instructions before you switch on the machine:
1.1 Voltage check: Before power cable is connected, please check the voltage of this appliance
against the supply.
Input voltage range 90~260V, frequency range 57-63Hz.
CAUTION - Damage would be caused if incorrect power voltage applied.
1.2 Hard Disk connection: Make sure the 40-Pin Hard Disk Data cable and the 4-Pin power
connectors are properly connected.
2
Recording
Press the REC key to enter the Recording Mode. And press the ꢀSTOP key to stop recording.
z “REC[M]” or “REC[Q]” sign will be indicated in top left corner on the screen, It mean you
select MUX or QUAD recording.
z “15P” sign will be indicated in top right corner on the screen, It mean the recording speed you
selected. 15P means 15 fields per second.
z “O” sign will be indicated in center corner on the screen, It mean the marked channel be
recorded.
™
™
For more information on Setting up Recording Mode, refer to Chapter 3 Record Setup
In Recording Mode, if there is a power failure or power lost for any reasons that cause a shut down
of this machine, it will be back to the Recording Mode automatically when power restored.
3
Playback
Press the ►PLAY button to into time search.
The following message will be displayed on the screen (The list of MASTER HARD DRIVE means
the time it start and end be recorded at this HDD).
TIME SEARCH
Use the ◄ or ► button to select items.
> MASTER HARD DRIVE
2004/JUN/30 10:12:03
Press the ▲ or ▼ button to decrease /
increase the number.
Press MENU to escape to exit the set
START TIME：2004/JUN/30 08:16:55
up mode.
END TIME：2004/JUL/09 12:09:09
Press ►PLAY button to play video forward.
z “PLAY” sign will be indicated in top left corner on the screen.
z “MUX or QUAD” sign will be indicated in top right corner on the screen, It mean the recording
mode you selected.
Press
Press
Rew Search button to play video reverse at 6 times speed fast rewind mode.
F.Fwd Search button to play video forward at high speed. Press the button again the
speed will be change circulative from ×2, ×4, to the highest ×6.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
z “REW” or “FF*2/4/6” sign will be indicated in top left corner on the screen.
Press
Pause button to pause (field by field) for forward. This function can be used in full
screen and quad mode (If you choose QUAD in recording mode than it can’t playback in full
screen).
z “PAUSE” sign will be indicated in top left corner on the screen.
Press the ꢀSTOP button to leave playback mode and resume the Live Mode.
When overwrite mode is enabled with 2 hard drives, drive which is overwriting will cause recording
time being divided to 2 periods as picture below:
TIME SEARCH
> MASTER HARD DRIVE
2004/JUN/13 04:12:03
RECORD SEGMENT 1
START TIME : 2004/JUN/21 07:51:13
END TIME : 2004/JUN/22 21:59:03
RECORD SEGMENT 2
START TIME : 2004/JUN/24 23:18:42
END TIME : 2004/JUN/25 12:15:50
PRESS[UP,DOWN,ENTER] TO SET
PRESS[PLAY] TO PLAY,[MENU] TO EXIT
There will be 2 periods of time as RECORD SEGMENT 1 and RECORD SEGMENT 2 in master
drive which means the oldest data and newest data both existing on the same hard drive.
Above rules will also apply to slave hard drive.
4
Hard disk and CF Card recommend
Maximum 2 pieces and at lease one hard disk should be connect, the capacity of hard disk from
40GB to 250GB for each.
When you restart the power of this appliance after install or replace new hard disk it will be format
automatically, we been tested the follow model of hard disk and recommend you use when you
install by yourself.
Brand
Model
Capacity
120GB
80GB
120GB
160GB
160GB
250GB
Speed (rpm)
7200 rpm
7200 rpm
7200 rpm
7200 rpm
7200 rpm
7200 rpm
Seagate
Seagate
Maxtor
Maxtor
Seagate
Maxtor
ST3120023A
ST380020A
6Y120L0
6Y160P0
ST3160023A
7Y250P0-A
We DO NOT suggest Samsung hard drive base on technical examination
CF Card Brand
Capacity
San Disk
San Disk
Transcend
128M
256M
128M
We DO NOT suggest Hagiwara CF Card
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Backup
The DVR support 2 methods for backing up:
1. VCR Backup
The DVR Provides composite signal output for back-up use. You can keep the Image data, and
simply just connected BNC connector, at the Back Panel of, with MONITOR OUT Connector. Press
VCR REC button, after decided what recording data need to keep, during Play-Back Mode.
2. Compact Flash (CF) Card Backup
After the insertion of CF card, network function will be temporary suspended. Please press
“Refresh” button to re-enable network function after CF card backup is done.
CF card backup is attached function of DVR network adapter; please ensure your DVR comes with
network function before using CF card backup.
You will only able to make CF card backup under single channel full screen playback mode if the
DVR recording in multiplexer mode.
You will only able to make CF card backup under quad playback mode if the DVR recording in quad
mode.
It could be 2 file formats for CF card backup c Single picture JPEG file d Video clip AVI file
It takes awhile on DVR system to be ready after CF card insertion. A CF mark will show up on
middle left screen under playback mode which indicates DVR system is ready for CF backup.
c. Single picture JPEG file
Run the DVR under playback mode and switch to the channel you are going to backup (you are not
allowed to perform CF card backup on single channel mode if your DVR recoding in quad mode) If
you press “COPY” key under multiplexer recording mode with quad playback the screen will shows
up PLEASE TURN TO FULL SCREEN MODE to remind you to switch to single channel
mode.
Press “PAUSE” button then press “COPY” key to back a single image into JPEG file on a CF card.
The screen will first shows up CF CARD TESTING PLEASE WAIT which indicates the DVR is
initializing and perform CF card testing for CF card backup and It takes around 1 second. Message
BACKUP TO CF CARD PLAESE STOP ANY UNNECESSARY JOBS will appear next in
the middle of the screen and message example 23MB/121MB 81% will appear in the bottom of
the screen which indicates 23M mage byte out of 121 mage byte are used and about 81% free
space left in the CF card. The single image CF card backup has been done successfully when all
messages are disappeared.
d. Video clip AVI file
Run the DVR under playback mode and switch to the channel you are going to backup (you are not
allowed to perform CF card backup on single channel mode if your DVR recoding in quad mode) If
you press “COPY” key under multiplexer recording mode with quad playback the screen will shows
up PLEASE TURN TO FULL SCREEN MODE to remind you to switch to single channel
mode.
Press “COPY” key to start backup a video clip images into AVI file under full screen normal speed
11
Download from Www.Somanuals.com. All Manuals Search And Download.
playback mode. The screen will start showing BACKUP TO CF CARD AVI FILE on top of the screen
for around 1 second and then appear AVI message in the left bottom screen which is indicating
DVR system is currently backing up video into buffer. Press “COPY” key again to terminated video
backup on your ideal period, the screen will show up CF CARD PROCESSING PLEASE WAIT .. .
It takes around 1 min to save AVI file into CF card, it depend on how big the file will be.
If the backup procedure has been done successfully, the message “CF CARD PROCESSING
PLEASE WAIT ….” will disappear and the message SAVE OK showing up.
If the backup action is failed, screen will show SAVE FAIL PLEASE CHECK CF CARD It could be
2 possibilities.
a. DVR causes internal error on buffer, please wait for 30 seconds and redo backup
procedure again.
b. Improper CF card insertion or connection shortage, please unplug your CF card and put
it back into CF card slot again.
Any CF card removal will trigger internal buzzer and message CF CARD REMOVED will shows up
on the screen.
When insufficient capacity occurred then message WARNING CF CARD INSUFFICIENT
CAPACITY will shows up, please busing your PC to free up some space on the CF card before
backup.
Using CF card reader to read images backup on a CF card as procedure below:
Hook up CF card USB adapter to the USB port on PC.
Follow the on CD instruction and install necessary driver files into your PC.
Insert the CF card into the card reader.
6
Alarm control
There are three types of alarms that the system can be configured to handle. They are 1.external
alarm, 2.video lost alarm and alarm of 3.motion detection.
When 1 and 3 types of alarm were triggered, it changes recording speed as alarm recording speed.
Video Lost alarm is enabled as default and cannot be changed. The buzzer will action and “V.LOSS”
sign will be indicated on the screen.
7
External alarm connector
External alarm functions only when DVR been set under recording mode. 4 input ports to receive
signals from external alarm and GND port for termination. When external alarm is triggered,
currents will be grounded through GND port to activate the external alarm.
a. Texts “ALM” will be displayed on OSD corresponding channel.
b. Relay action.
c. Recording speed will be switch from normal mode to alarm mode (refer to chapter 4 about
recording setting).
d. If setting “A” has been set in schedule recording, will only perform recording when alarm is
12
Download from Www.Somanuals.com. All Manuals Search And Download.
triggered during schedule “A” period.
Terminal connector：
Pin 1-4
GND
N.C
----- ALARM1-ALARM4，Camera alarm input.
----- GND
----- Relay N.C，Alarm output N.C
----- Relay COM
COM
N.O
----- Relay N.O，Alarm output N.O
8
Network
Network function is optional, please ensure that you have proper DVR model for network installation.
Network setup in this DVR can be done only by TCP/IP network remote computer. With network
function the DVR will support remote recording and remote surveillance. Please refer to network
setup manual for instructions.
SPCIFICATIONS
Image System
NTSC
PAL
Display
Record
720×480
640×224
BNC × 4
BNC × 4
BNC × 2
720×576
640×272
Resolution
Video Input
Video Looping output
Video Output
Display Frame
4 × 30 fields/sec
Max 30 fps
4 × 25 fields/sec
Max 25 fps
Recording Frame Rate (QUAD)
Recording Frame Rate (MUX)
Storage Media
Max 30 / 4 fps
Max 25 / 4 fps
Max 2 IDE Hard Disks
Image Format
M-JPEG
Low：8K bytes/field
High：15K bytes/field
Medium：10K bytes/field
Compress Rate
Recording Mode
Playback Speed
Best：20K bytes/field
Manual / Alarm / Schedule
Fast Forward ×2 ×4 ×6 / Fast Reverse ×6
Frame by Frame Forward Playback
On Screen Display & Setup
Alarm Input
Time/Date/Setup Menu
×4
Relay Output
Password Control
Event List
NO or NC Programmable Contact ×1
One for HDD format
Max. 63 records/H.D.D
Motion Detection
Buzzer
Yes
Yes
Video loss
Yes
Key Lock
Yes
Network Function
Backup
Optional
CF Card
Power Input
Dimensions
AC 90-260 V Input ( 60/50 Hz )
55mm (H) × 432mm (W) × 321mm (D)
4.5kg (w/o H.D)
Weight kg
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
RECORDING TIME LENGTH
Recording time length is related to recording speed and recording quality. Tables below are offered for
your reference.
Record Mode=MUX
Record Mode=QUAD
Recording length under quad mode will shorter than multiplex mode and PAL will shorter than NTSC.
80GB H.D.D Record Mode=MUX
NTSC Field/Sec
30/FS 15/FS 10/FS 7/FS
5/FS
4/FS
3/FS
2/FS
1/FS
maximum 38 hr
76 hr 114 hr 160hr 228hr 285hr 380 hr 570 hr 1140hr
57 hr 114Hr 171hr 240hr 342hr 428hr 570 hr 855 hr 1710hr
71 hr 142hr 213hr 298hr 426hr 532hr 710 hr 1065hr 2130hr
100hr 200hr 300hr 420hr 600hr 750hr 1000hr 1500hr 3000hr
high
medium
low
Recording
Quality
80GB H.D.D Record Mode=QUAD
NTSC Field/Sec
30/FS 15/FS 10/FS
7/FS
80 hr 114hr 142hr 190hr 285hr 570 hr
87 hr 120hr 171hr 214hr 285hr 426hr 870 hr
5/FS
4/FS
3/FS
2/FS
1/FS
maximum 19 hr
38 hr
57 Hr
57 hr
high
medium
low
29 hr
35 hr
Recording
Quality
70 hr 105 hr 148hr 213hr 266hr 350hr 532hr 1050hr
50 hr 100 hr 150 hr 208hr 300hr 375hr 500hr 750hr 1500hr
80GB H.D.D Record Mode=MUX
PAL Field/Sec
25/FS
12/FS
8/FS
6/FS
4/FS
3/FS
2/FS
1/FS
maximum
high
35 hr
72 hr
110 hr
145 hr
218 hr
291 hr
437 hr
875 hr
46 hr
67 hr
98 hr
95 hr
139 hr
204 hr
144 hr
209 hr
306 hr
190 hr
278 hr
408 hr
287 hr
418 hr
612 hr
383 hr
558 hr
816 hr
575 hr
837 hr
1225hr
1150 hr
1675 hr
2450hr
Recording
Quality
medium
low
80GB H.D.D Record Mode=QUAD
PAL Field/Sec
25/FS
12 hr
16 hr
23 hr
34 hr
12/FS
25 hr
33 hr
48 hr
70 hr
8/FS
37 hr
50 hr
72 hr
106 hr
6/FS
50 hr
66 hr
95 hr
141 hr
4/FS
75 hr
3/FS
2/FS
1/FS
maximum
high
100 hr
133 hr
191 hr
283 hr
150 hr
200 hr
287 hr
425 hr
300 hr
400 hr
575 hr
850 hr
100 hr
143 hr
212 hr
Recording
Quality
medium
low
CF Card Backup time
Capacity=128M
Single Image file size
Single picture JPEG file
3100 fields
Video clip AVI file
25 minute
40K
50K
60K
2500 fields
2000 fields
20 minute
16 minute
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6
HARD DRIVE INSTALLATION PROCEDURES
1. Hard drive jumpers need to be set properly in order to make DVR function correctly.
2. Instructions below are for second hard drive installation. If you prefer to have only one drive, please
ignore instruction below. Remove DVR top cover by taking out screws from location shown below:
①
.
②
③
④
⑤
⑥
3. Below picture indicates DVR which one without a H.D.D installed.
4. Please refer to the instruction from hard drive manufactory for correct jumper setting on (master
/slave) mode of the hard drive, mounting the hard drive over DVR base by facing IDE interface to
DVR main board. Match screw holes from bottom to bottom of hard drive and the DVR. Turn over
the DVR from top to bottom side and then mounting up the hard drive by using screws from attached
accessory pack as picture below:
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Hooking up IDE cable and power cable to the hard drive as picture below, please take a note on
that the red line on IDE cable must be next to power cable in order to have correct instillation.
6. This DVR supports maxima 2 hard drives, please take a note on cable length that you use to hook
up with the hard drive.
7. Restore top cover then hook up with power and monitor a hard drive status message will appear if
it’s been installed successful.
Attentions：
1. Hard drive master and slave mode must be set correctly.
2. Primary hard drive must be set as master and slave for secondary.
3. Make sure power cable is unplugged before hard drive installation starts.
4. IDE cable and power cable must be hooking up correctly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|