S E R VO 4 0 6 0 / 4 1 2 0
Q
U
A
D
AMPLIFIER
O W N E R S M A N U A L
®
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Congratulations on purchasing the Samson Servo Quad Amplifier! Although designed for easy
operation, we suggest you first take some time to go through these pages so you can fully understand
how we’ve implemented a number of unique features.
The Servo Quad Amplifier is actually four discrete power amplifiers in a single chassis, optimized for use
in live performance, recording studios, and permanent installations. This manual covers two Servo Quad
Amplifier models, which differ primarily in terms of their power rating: the Servo 4060, which delivers
60 watts per channel into 4 ohms (or, in bridged mode, 120 watts into 8 ohms) and the Servo 4120,
which delivers 120 watts of power per channel into 4 ohms (or, in bridged mode, 240 watts into 8 ohms).
Both models operate over the full frequency spectrum (from 20 Hz to 50 kHz) and include dual bridging
switches, four sets of binding post (banana jack) outputs, and both electronically balanced 1/4" TRS and
unbalanced RCA-type input connectors
Suggested applications for the Servo Quad Amplifier include:
• Bi-amping applications - Because it is actually four amplifiers in one, the Samson Servo Quad
Amplifier is particularly well-suited (in conjunction with appropriate crossover circuitry) to power small
and medium size bi-amped speaker systems.
• Amplification for main or nearfield monitors in both professional and project studios - Its superb audio
specs and whisper-quiet performance (its convection cooling design means there is no fan) make the
Servo Quad Amplifier the perfect complement to any recording studio.
• Home Theatre applications - The sheer flexibility offered by the Servo Quad Amplifier (four discrete
amplifier sections plus two independent bridging switches) makes it the perfect addition to any home
theatre, in conjunction with any DVD player or other surround sound system. For example, use two
channels to drive your front left/right speakers and the other two to drive your satellite rear speakers.
Or use two channels for your front left/right speakers and bridge the remaining two channels to drive
your center channel or subwoofer with power galore—you’re limited only by your imagination!
• As an extension to a home hi-fi system - The Servo Quad Amplifier boasts professional specs which
far exceed that of most consumer products. For a real “studio” experience in your own home, try
connecting your home hi-fi amplifier’s auxiliary outputs to the Servo Quad Amplifier’s inputs (thus
using your hi-fi amp as a preamplifier) and then connect your existing speakers to the Servo Quad
Amplifier’s outputs. If you fall in love with the sound (as we’re sure you will), you might want to sub-
stitute a professional pre-amplifier for your existing hi-fi amp—and, from there, you may well end up
graduating to higher-level speakers. High quality sound is addicting—don’t say we didn’t warn you!
• Powering public address systems in permanent installations - The Servo Quad Amplifier can be used
to effectively drive PA speakers in installations such as classrooms and corporate conference rooms.
• Onstage monitoring - In small and medium-sized onstage areas (such as in clubs, lounges, etc.), the
Servo Quad Amplifier can be used to drive stage monitors, allowing the performers to hear
themselves without having to rely on onstage equipment amplification.
• MIDI rack monitoring - MIDI musicians can easily incorporate the Servo Quad Amplifier into their
existing rack of gear. Combined with a pair of high quality stage or studio monitors, this makes for an
excellent monitoring system that can accurately reproduce the broad range of frequencies typically
output by devices such as synthesizers, samplers, and digital audio workstations.
In these pages, you’ll find a detailed description of the many features of the Servo Quad Amplifier, as
well as a guided tour through its front and rear panels, step-by-step instructions for setting up and using
your Servo Quad Power Amplifier, a description of suggested applications, reference appendices, and
full specifications. You’ll also find a warranty card enclosed—please don’t forget to fill it out and mail it in
so that you can receive online technical support and so we can send you updated information about
these and other Samson products in the future.
SPECIAL NOTE: Should your unit ever require servicing, a Return Authorization number (RA) is
necessary. Without this number, the unit will not be accepted. Please call Samson at 1-800-372-6766
for a Return Authorization number prior to shipping your unit. Please retain the original packing materials
and, if possible, return the unit in its original carton and packing materials.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Se rvo Quad Amplifie r Fe ature s
The Samson Servo Quad Amplifier utilizes the latest technology in professional power amplifier design.
Here are some of its main features:
• Power to spare - Each channel of the Servo 4060 delivers 60 watts into 4 ohms (or, in bridge stereo
mode, 120 watts into 8 ohms). Each channel of the Servo 4120 delivers 120 watts of power into 4
ohms (or, in bridge stereo mode, 240 watts into 8 ohms).
• Clean, crisp sound - Impressive audio specifications such as 0.05% THD, S/N of 95 dB, crosstalk of
-70 dB, and frequency response of 20 Hz to 50 kHz guarantee ultra-clean sound quality in any live or
recording environment.
• Independent input controls for all four channels, with 41-position detents showing attenuation in dB.
• Independent five-segment LED meters for each of the four channels continuously display power
output levels and allow you to correct for overloading (clipping) conditions.
• Front-panel Protection lights show you at a glance overheating or faulty wiring conditions.
• Both electronically balanced 1/4" TRS and unbalanced RCA-type input connector jacks are provided.
• Binding post (banana jack) output connectors.
• Convection cooling (no fan) makes for whisper-quiet operation even in critical listening environments
such as recording studios.
• Unique bipolar circuit design that continuously keeps DC output during idling at or near 0 volts (thus
keeping idle speakers at their 0 point). This serves to minimize heat overload problems by effectively
preventing the Servo Quad Amplifier from applying power when unnecessary.
• Protection relay circuitry (linked to the DC offset circuitry) that prevents “thumps” when powering on
or off. This means that you can use the Servo Quad Amplifier with a single power strip into which a
mixer or other audio devices are connected, without danger of damage to connected speakers.
• Rugged construction (an all-steel chassis with a titanium finish and a lightweight anodized aluminum
heat sink) makes the Servo Quad Amplifier eminently roadworthy.
• Flexible design allows the Servo Quad Amplifier to be used free-standing or, with the use of included
rack ears, mounted in any standard 19" rack (taking just two rack spaces).
• Three-year warranty.
• Last but certainly not least, value. The Samson Servo Quad Amplifier has been designed from the
ground up to deliver excellent yet affordable sound quality.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide d Tour - Front Pane l
4
4
4
5
4
5
2
-20 dB -10 dB -3 dB
0
dB CLIP
70 100%
-20 dB -10 dB -3 dB
0
dB CLIP
70 100%
-20 dB -10 dB -3 dB
0
dB CLIP
70 100%
-20 dB -10 dB -3 dB
0
dB CLIP
70 100%
10
30
50
10
30
50
10
30
50
10
30
50
-16
-16
-16
-16
CH3/4
CH1/2
POWER
S A M S O N
PROTECTION
PROTECTION
SERVO 4120 - 120 WATT X 4 AMPLIFIER
LEVEL
LEVEL
LEVEL
LEVEL
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
3
1
3
3
3
1: Power switch - Use this to power the Servo Quad Amplifier on or off.
2: Power LED - Lit whenever the Servo Quad Amplifier is powered on.
3: Channel input controls (Ch 1 - 4) - These four 41-position knobs allow you to adjust the input level
of the signal arriving at the rear-panel input jacks (see #4 and #5 on the following page). At their fully
counterclockwise position (labeled “∞”), the signal is infinitely attenuated (completely off). At their fully
clockwise position (labeled “0 dB”), the signal is at unity gain (that is, no attenuation). When 0 dBm of
signal arrives at the input jacks and the Channel Input controls are set to their “0 dB” position, the
Servo Quad Amplifier delivers full power output.
4: LED meters (Ch 1 - 4)- These five-segment LED meters continuously monitor the power output level
for that channel. For convenience, the segments are labeled as follows, from left to right: -20 dB / 10%,
-10 dB / 30%, -3 dB / 50%, 0 dB / 70%, and CLIP / 100%. When the left-most (-20 dB / 10%) segment
is lit, the Servo Quad Amplifier is operating at 10% of its power capacity. When the right-most
(CLIP / 100%) segment is lit, signal is being output at full strength. For the best signal-to-noise ratio,
the right-most (CLIP / 100%) segment should light occasionally during peak levels; if it lights frequently,
you may be overloading the Servo Quad Amplifier and a distorted (“clipped”) signal is probably being
output. If this occurs and backing off the Input Level control delivers too low an output level for your
application, consider using bridge stereo mode (see the “Bridge Stereo Mode” section on page 7 in this
manual for more information).
5: Protection LEDs (Ch 1/2, Ch 3/4) - These go on for approximately five seconds whenever the
Servo Quad Amplifier is powered on and fade slowly when the amp is powered off. When lit, 0 volts DC
are provided to all connected speakers, thus muting them and preventing any “thump” from occurring.
For a complete description of the conditions under which this light goes on, see the section entitled
“The Servo Quad Amplifier Protection Circuitry” section on page 6 of this manual.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide d Tour - Re ar Pane l
3
1
3
-
+
+
-
-
+
+
-
SERVO 4120
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
QUAD AMPLIFIER
!
USE CLASS 2 WIRING
SERIAL NUMBER
-
+
+
-
-
+
+
+
-
4Ω 120W
AC
INLET
4Ω 120W
CH4
CH3
USA
&
CANADA 115V
-
60Hz
CH2
CH1
MAX. LOAD
emc
MAX. LOAD
EUROPE
&
UK 230V
-
50Hz
-
+
-
650W MAX.
EUR . USA . JPN
MONO 8Ω
MONO 8Ω
S A M S O N
CAUTION:
ATTENTION:
DISCONNECT SUPPLY CORD
DEBRANCHER AVANT DE
REMPLACER LE FUSIBLE.
UTILISERUN FUSIBLE DE
RECHANGE DE MEM TYPE.
AVIS;
SAMSON TECHNOLOGIES CORP., U.S.A.
RISQUE DE CHOC ELECTRIQUE
BEFORE CHANGING FUSE.
NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
BRIDGE
BRIDGE
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE OF FUSE.
USA
8A/125V (115V)
EUROPE AND UK
&
CANADA
OFF
ON
OFF
ON
T
FUSE
CH4
R
CH2
L
CH3
R
CH1
L
T
6.3A/250V (230V)
4
5
4
5
6
2
6
1: AC input - Connect the supplied standard 3-pin “IEC” plug here.
2: Fuse holder - In the Servo Quad 4060, insert an 6 amp, 125 volt fuse here for 115 volt operation, or
a 3.15 amp, 250 volt fuse for 230 volt operation. In the Servo Quad 4120, insert an 8 amp, 125 volt fuse
here for 115 volt operation, or a 6.3 amp, 250 volt fuse for 230 volt operation. We recommend the use
of normal (as opposed to slow-blow) fuses. WARNING: Fuses should only be replaced with the power
cord disconnected.
3: Binding post (banana jack) output connectors (Ch 1 - 4) - Use these to connect each channel of
the Servo Quad Amplifier to loudspeakers. Be sure to connect the loudspeaker correctly, with the red
(+) terminal normally connected to the positive input of the speaker and the black (-) terminal normally
connected to the negative input of the speaker. See the “Bridge Stereo Mode” section on page 7 in this
manual for speaker connection instructions when using the Servo Quad Amplifier in bridge mode.
4: Balanced Inputs* (Ch 1 - 4) - Connect incoming signal to these electronically balanced 1/4" TRS
(Tip/Ring/Sleeve) jacks, wired as follows: Tip hot, Ring cold, and Sleeve ground. Use balanced three-
conductor cabling and TRS plugs wherever possible (unbalanced two-conductor plugs can also be
inserted into these inputs, but you’ll get better signal quality and less outside noise and hum if you
use balanced lines). Note that the Servo Quad Amplifier balanced inputs are 6 dB higher in gain than
the balanced inputs (see #5 below). The Servo Quad Amplifier accepts input levels of any strength but
needs at least 0 dBm to get maximum power.
5: Unbalanced Inputs* (Ch 1 - 4) - Connect incoming signal to these unbalanced RCA-type jacks.
The Servo Quad Amplifier accepts input levels of any strength but needs at least 0 dBm to achieve
maximum power. Note that the Servo Quad Amplifier unbalanced inputs are 6 dB lower in gain than the
balanced inputs (see #4 above).
6: Bridge switch - For normal operation, place this switch at its left (“OFF”) position. When placed at its
right (“ON”) position, each of the two amplifier sections (channel 1 and channel 2 and/or channel 3 and
channel 4) are bridged, providing full 120 or 240 watt power output, depending upon the Servo Quad
model you’re using. For more information, see the “Bridge Stereo Mode” section on page 7 in this
manual. WARNING: Due to the extremely high power output of the Servo Quad Amplifier when used in
Bridge Stereo mode, be sure to use only 8 ohm loudspeakers sufficiently rated to handle the resultant
wattage.
* If required, both the balanced and unbalanced inputs can be used simultaneously.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Se tting Up and Us ing the Se rvo Quad Amplifie r
Setting up your Servo Quad Amplifier is a simple procedure which takes only a few
minutes:
1. Remove all packing materials (save them in case of need for future service) and
decide where the amplifier is to be physically placed—it can be used free-standing or
mounted in a standard 19" rack, requiring only two rack spaces. When installed,
make sure that there is good ventilation around the entire unit (we recommend
using spacer panels, especially if multiple amplifiers are used in a rack. Before
BRIDGE
rack-mounting, use a Philips screwdriver to attach the included rack ears.
2. Set either or both rear panel Bridge switches as desired (see page 7 in this
manual for more information).
OFF
ON
3. Make the speaker connections, using the binding post (banana plug) output
connectors on the rear panel. It is never a good idea to power up any amplifier that is
not connected to loudspeakers. In normal modes of operation, any loudspeakers
with a minimum impedance load of 4 ohms (that is, 4 ohms or greater) can be used;
however, in Bridge Stereo mode, 8 ohm speakers must be used. Be sure to connect
the loudspeaker correctly. In normal mode, connect them with the red (+) terminal
connected to the positive input of the speaker and the black (-) terminal connected to
the negative input of the speaker. Refer to page 7 in this manual for connection
instructions when using the Servo Quad Amplifier in Bridge Stereo mode. If you are
using the Servo Quad Amplifier for bi-amping applications, refer to the “Bi-amplifica-
tion Applications” section on page 8 in this manual for more information.
Bridge on/off switch
-
+
+
-
-
+
+
-
4Ω 120W
CH2
CH1
MAX. LOAD
+
-
MONO 8Ω
Speaker connectors
4. Next, make the signal input connections, using the electronically balanced 1/4"
and/or the unbalanced RCA-type input connectors on the rear panel. If your mixer or
crossover network has balanced outputs, use the Servo Quad Amplifier’s electroni-
cally balanced inputs (unbalanced two-conductor plugs can also be inserted into
these inputs, but you’ll get better signal quality and less outside noise and hum if you
use balanced lines). If you are using the Servo Quad Amplifier for bi-amping applica-
tions, refer to the “Bi-amplification Applications” section on page 8 in this manual.
CH2
L
CH1
L
Input connectors
5. On the front panel of the Servo Quad Amplifier, turn all four Channel input controls
fully counterclockwise (to their “∞” setting). Then connect the supplied 3-pin “IEC”
cable to the rear panel IEC connector and to any grounded AC socket. Because of
the relay protection circuitry built into the Servo Quad Amplifier, you can even plug it
into the same power strip that other audio devices (such as a mixing console) are
connected to. You can then turn on all devices at once with the single power strip on-
off switch, with no danger of damaging connected speakers by generating “thumps.”
IEC connector
6. Press the front panel Power switch in order to turn on the Servo Amplifier.
The Power LED will light and the two Protection LEDs will go on for approximately
five seconds, and then switch off (you’ll hear a click when they do so).
CH3/4
POWER
PROTECTION
7. Apply an input signal to the amplifier at or about 0 dbM (if sending signal from a
mixer, drive the output meters at approximately 0 vu). While the input signal is
present, slowly raise the Channel input controls until the desired sound level is
achieved. The five-segment LED meters above each Channel input control will show
you the continuous power output of the Servo Quad Amplifier as signal is being
passed. For the best signal-to-noise ratio, the Servo Quad Amplifier should normally
be run with the Channel input controls at or near maximum (fully clockwise, at the
“0 dB” position) and the right-most (CLIP / 100%) segment should light occasionally
(but not frequently) during peak levels. If you are using a mixing board that has a
master output level control (sometimes called “control room level”), use it to attenuate
the signal as necessary to achieve the desired speaker level.
Power switch and
Protection LED
If you encounter difficulty with any aspect of setting up or using your Servo Quad
Amplifier, you can call Samson Technical Support (1-800-372-6766) between
9 AM and 5 PM EST.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The Se rvo Quad Amplifie r Prote ction Circuitry
As noted in the “Guided Tour” section of this manual, the Servo Amplifier's front
panel Protection lights indicate the activity of the relay speaker connection
circuitry. When the Protection lights are lit, this circuitry is inactive, and all
connected speakers are muted (provided with 0 volts DC), thus protecting them
and preventing any audible “thump” from occurring.
CH3/4
PROTECTION
The following conditions will cause the Protection lights to go on:
• Initial power-up: For approximately five seconds after initial power-up, the
relay speaker connection circuitry is deactivated and the speaker output is
muted. If everything is operating normally, you will hear an audible click at the
conclusion of this brief period, as the circuitry is activated and the Servo Quad
Amplifier begins delivering signal to connected speakers. It is normal for the
Protection light to fade gradually after the amplifier is powered off.
WARNING: If a Protection light fails to go out (and you fail to hear the
accompanying audible click) approximately five seconds after power-up,
turn the Servo Quad Amplifier off immediately and check all external
devices and wiring for possible shorts or other defects.
• Overheating: A temperature sensing device in the Servo Quad Amplifier will
cause the relay speaker connection circuitry to be deactivated (and the
Protection light to go on) whenever the operating temperature of the unit rises
above a safe level. To guard against this problem, make sure the Servo Quad
Amplifier receives adequate ventilation on all sides (see page 5 for more
information); in extreme environmental conditions, you may also want to
consider the use of cooling fans.
• Severe overcurrent conditions: This occurs whenever the signal being input to
the Servo Quad Amplifier rises to a level above 20% THD (Total Harmonic
Distortion).
• Shorted speaker cables: This will occur if, due to faulty wiring, the hot and
ground signals being output by the Servo Quad Amplifier short one another.
• Output impedance drops below 2 ohms: This can occur if the Servo Quad
Amplifier is connected to inappropriate speaker systems (see the “Setting Up
and Using the Servo Quad Amplifier” section on page 5 in this manual for more
information).
• DC voltage detected at speaker output: The most likely cause of this is an
internal failure.
In general, any time either or both of the Protection lights go on (other than
during the approximately five seconds following initial power-up), there is reason
to be concerned. If this occurs, turn the Servo Quad Amplifier off immediately
and carefully check all wiring and external devices in order to locate and correct
the condition that caused the light to go on in the first place.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Bridge Ste re o Mode
The Servo Quad Amplifier provides two rear-panel switches that allow it to be
used in a unique bridge stereo mode. When these switches are in their “Off”
(left) position, the Servo Quad Amplifier functions as a true quad amplifier, where
each of the four independent amplifier channels can receive different input signal
and produce independent output signal. However, when either switch is placed
in the “On” (right) position, the pair of amplifier channels (1/2 or 3/4) process only
the signal present at one input, thus producing a monophonic output signal with
a true 120 watt (in the case of the Servo Quad 4060 model) or 240 watt (in the
case of the Servo Quad 4120 model) output into 8 ohms. When both Bridge
switches are placed in the “On” position, the Servo Quad amplifier operates in
bridge stereo mode, acting like a true stereo amplifier, delivering 120 watts of
power per channel (in the case of the Servo Quad 4060 model) or 240 watts of
power per channel (in the case of the Servo Quad 4120 model).
BRIDGE
OFF
ON
WARNING: Bridge stereo mode is to be used only when the
Servo Quad Amplifier is connected to an 8 ohm speaker load.
Use of bridge stereo mode with speaker loads of 4 ohms or less can result
in severe damage to the Servo Quad Amplifier due to excessive heat and
current limiting and will void your warranty!
The illustration on the left shows how this works. In bridge stereo mode, the
polarity (phase) of the channel 1 output signal is reversed relative to that of the
channel 2 output signal (similarly, the channel 4 output signal is reversed relative
to that of channel 3). Channels 1 and 2 then process the signal being input to
channel 2 (and channels 3 and 4 process the signal being input to channel 3),
but the speaker load is connected so that power is derived from both channels.
The effective voltage swing seen by the load is thus doubled so that the power
output is doubled.
INPUT
(CHANNEL 2)
CHANNEL 2
(+) OUTPUT
When using the Servo Quad Amplifier in bridge stereo mode, be sure to connect
each loudspeaker as shown in the illustration below (and as silkscreened on the
rear panel), with the red (+) terminal of channel 2 (and/or channel 3) connected
to the positive input of the speaker and the red (+) terminal of channel 1
(and/or channel 4) connected to the negative input of the speaker.
Do not use the black (-) output terminal of either channel (the speaker load
must “float” away from the amplifier chassis).
CHANNEL 1
(+) OUTPUT
-
+
+
-
-
-
+
+
-
-
SERVO 4120
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
QUAD AMPLIFIER
!
USE CLASS
2
WIRING
-
+
+
SERIAL NUMBER
-
+
+
+
4Ω 120W
4Ω 120W
CH4
CH3
CH2
CH1
AC
INLET
MAX. LOAD
USA
EUROPE
650W MAX.
&
CANADA 115V
-
60Hz
MAX. LOAD
emc
A . JPN
+
-
&
UK 230V
-
50Hz
-
MONO 8Ω
MONO 8Ω
E
U
R .
US
S A M S O N
CAUTION:
DISC NNE T SUPPLY C
BE RE CHANGING FUSE.
R C NTINUED PROTE TIO
AGAINST RISK OF FIRE, REPLAC
NLY WITH SAME TYPE OF FUSE.
ATTENTION:
DEBRANCHER AVANT DE
O
C
O
RD
AVIS;
SAMSON TECHNOLOGIES CORP., U.S.A.
BRIDGE
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
F
O
REMPLAC
UTILISERUN FUSIBLE DE
RE HANGE DE ME TYPE.
ER LE FUSIBLE.
BRIDGE
F
O
O
C
N
DO NOT EXPOSE THIS EQUIPMENT
TO RAIN OR MOISTURE.
E
C
M
O
USA
8A/125V (115V)
EUROPE AND UK
6.3A/250V (230V)
&
CANADA
OFF
ON
OFF
ON
T
FUSE
CH4
R
CH2
L
CH3
R
CH1
L
T
+
-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Bi-amplification Applications
Because the Samson Servo Quad Amplifier actually contains four discrete power
amplifiers in a single chassis, it is particularly well-suited for use with bi-amped
speaker systems. These systems utilize active crossover networks (sometimes
called electronic crossovers) that are specially designed to handle low-wattage
line-level signals. As shown in the illustration on the right, the crossover in such
a system is placed just prior to the power amplifier in the signal chain.
LEFT
RIGHT
INPUT
SIGNAL
INPUT
SIGNAL
ACTIVE CROSSOVER
NETWORK
LEFT
LF HF
RIGHT
LF HF
The circuitry in a two-way active crossover network divides the incoming signal
into its high and low frequency components. Those frequencies above a
specified crossover point are sent to one discrete output and those below the
crossover point are sent to the other. Each output is then connected to a
separate power amplifier channel input. In this way, one amplifier powers the
loudspeaker’s low frequency drivers (“woofers”) and another powers the
loudspeaker’s high frequency drivers (“tweeters”).
OUT OUT
OUT OUT
CH1 CH2
CH3 CH4
IN
IN
IN
IN
SERVO QUAD
AMPLIFIER
The advantage to bi-amping is not only enhanced loudspeaker performance
(since each speaker driver is receiving optimized signal) but also greatly reduced
distortion. This is because most of the energy in musical signals lies in its low
frequency components (next time you’re listening to a piece of popular music,
contrast the level of kick drum and bass guitar to the other instruments). When
both low and high frequencies are present in a signal, these high-energy low
frequency signals can eat up all the available headroom in a power amplifier,
leaving none for the higher frequencies. The end result is nasty clipping
distortion of the high frequency material. The use of an active crossover network
effectively eliminates this problem—in fact, you’ll get cleaner, perceptively louder
signal than if you were to use a single higher-power amplifier instead!
CH1 CH2
OUTOUT
CH3 CH4
OUT OUT
LEFT
LEFT
RIGHT
RIGHT
WOOFER
INPUT
TWEETER WOOFER TWEETER
INPUT
INPUT
INPUT
Of course, with four amplifiers at your disposal, you can use your Samson
Servo Quad Amplifier to bi-amp both the left and right signals in a stereo system.
Simply use a stereo active crossover network and route the two left outputs
(low and high frequency) to the Servo Quad Amp channel inputs 1 and 2
and the two right outputs to channel inputs 3 and 4. You can then use the
front-panel input level controls to adjust the relative levels of each output signal.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appe ndix A: Line arity vs . Fre que ncy Swe e p
AUDIO PRECISION servo 4060/4120 THD +N (%) & LEVEL (W) vs FREQ (Hz)
0dB ref
5.0000
THD
1.000
.9000
.8000
.7000
.6000
.5000
.4000
.3000
.2000
.1000
0.0
Ap
4.0000
3.0000
2.0000
1.0000
0.0
-1.000
-2.000
-3.000
-4.000
-5.000
10
100
1k
10k
50k
Linearity (0 dB Ref) vs. frequency sweep
20 Hz - 50 kHz
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Appe ndix B: Powe r Output vs . THD
AUDIO PRECISION servo 4060/4120 THD +N (%) & LEVEL (W) vs FREQ (Hz)
THD
Watts
.50000
80.000 / 160.000
Ap
.45000
.40000
.35000
.30000
.25000
.20000
.15000
.10000
.05000
73.333 / 146.666
66.667 / 133.333
60.000 / 120.000
53.333 / 106.666
46.667 / 93.333
40.000 / 80.000
33.333 / 66.666
26.667 / 53.333
20.000 / 40.000
13.333 / 26.666
6.666 / 13.333
0.000 / 0.000
0.0
1k
10k 20k
10
100
Power output (Servo 4060 @ 60 W, Servo 4120 @ 120 W) vs. Total Harmonic Distortion
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Spe cifications
1. Rated Output Power, per channel
At 1 kHz, 4 ohm, .<0.05% THD+N
Model 4120
120 W
60 W
Model 4060
At 1 kHz, 4 ohm, 1% THD+N
Model 4120
150 W
80 W
Model 4060
At 1 kHz, 8 ohm, <0.05% THD+N
Model 4120
120 W
60 W
Model 4060
At 1 kHz, 8 ohm, 1% THD+N
Model 4120
130W
64 W
Model 4060
2. Typical Distortion, per channel
THD+N (80 kHz LPF @ 1 kHz, rated output power)
IMD (SMPTE 4:1, 60 Hz & 7 kHz @ rated output power)
.005%
.015%
3. Signal To Noise Ratio
(22 Hz - 22 kHz bandwidth @ dB below rated output power)
95 dB
4. Frequency Response
5. Input Sensitivity
20 Hz - 50 kHz, 0 - 3 dB
+4 dBu to achieve rated power
(Level control set to maximum)
6. Crosstalk (adjacent channels)
7. Output DC Offset Voltage
8. Dimensions (without rack ears)
-70 dB, 1 kHz
0 ± 50 mV, DC Servo Controlled
17.5 in (w) x 10.75 (d) x 3.25 (h)
444 mm (w) x 273 (d) x 82.5 (h)
9. Weight
Model 4120
Model 4060
29.5 lbs • 13.4 kg
25 lbs • 11.3 kg
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Produced by On The Right Wavelength for Samson Technologies Corp.
Copyright 1997, Samson Technologies Corp.
Printed April, 1997
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 516-364-3888
Download from Www.Somanuals.com. All Manuals Search And Download.
|