Samson DJ Equipment XP510I User Guide

XP510i Quick Start  
XP510i Quick Start contd  
Specifications*  
System Specifications  
Maximum Output Power  
250 W + 250 W @ 8 Ω  
Unpacking and Setting Up the XP510i  
Using a Line Level Signal  
Crosstalk (at 1 kHz)  
• Unpack all the system components from the shipping carton and save all packing materials in the (unlikely) event  
your unit ever needs to be returned for service.  
• Be sure that the XP510i’s Power switch is set to the OFF position.  
-70 dB between input channels  
-70 dB between input/output channels  
E PEDITION  
• Turn all of the channel VOLUME (VOL) controls fully counterclockwise to the “0position.  
• Connect the power cable to an AC outlet.  
Maximum Output Level (0.5% T.H.D. @ 1kHz)  
+22dBu(MONITOR L/R) @ 10 kΩ  
+14 dBu (REC) @ 10 kΩ  
• Remove the mixer by turning the quarter turn screw counterclockwise towards the RELEASE position.  
PORTABLE PA SYSTEM  
SPEECH/MUSIC  
167 Hz, 3dB/Octave  
XP510i  
LOCK  
• If using channels 1-4, set the MIC/LINE switch to the LINE position.  
T.H.D  
Input Channel Equalization  
HIGH: 10 kHz shelving 15 dB  
LOW: 100 Hz shelving 15 dB  
<0.1% @+14 dB 20 Hz ~ 20 kHz (MONITOR L/R,REC L/R) @ 10 kΩ  
• Using standard 1⁄4-inch cables, connect a line level signal from a keyboard into the XP510i’s LINE INPUTS.  
Frequency Response  
RELEASE  
20 Hz ~ 20 kHz +/-1 dB, 10 kΩ (MONITOR L/R)  
20 Hz ~ 20 kHz +0/-1 dB, 10 kΩ (REC L/R)  
LIMIT/COMP Switch  
DOWN = Comp, UP = Limit (CH1/2)  
Hum and Noise (Input GAIN=Maximum Input sensitivity, MIC)  
-112dBu equivalent input noise ( Rs = 150 Ω )  
Phantom Power  
+15V DC  
• Carefully hold the mixer to remove it from the speaker.  
-90dBu  
-80dBu  
Residual noise (MONITOR L/R) all Levels at Minimum  
MONITOR at nominal level and all channel Levels  
minimum.  
Power Source/Power Consumption  
AC INPUT 100 V~240 V, 50/60 Hz, 600 W MAX.  
Electric Acoustic  
Guitar  
-70dBu  
MONITOR at maximum level and all channel Levels  
minimum.  
Weight  
52.8 Ib (24 Kg)  
Maximum Voltage Gain  
50dB MIC 1/2(XLR,LIMIT Position) IN TO MONITOR L/R  
60dB MIC 3/4(XLR) IN TO MONITOR L/R  
40dB MIC 1/2(PHONE TRS,LIMIT Position) IN TO MONITOR L/R  
50dB MIC 3/4(PHONE TRS) IN TO MONITOR L/R  
14dB CH 1/2 LINE(PHONE TRS,LIMIT Position,MIC/LINE SW IN) IN TO  
MONITOR L/R  
Dimensions  
22.7’’(W) x 12.6’’(D) x 22’’(H)  
577 mm(W) x 320 mm(D) x 560 mm(H)  
Owners Manual  
Where 0 dBu = 0.775 V and 0 dBV = 1 V  
24dB CH 3/4 LINE(PHONE TRS,MIC/LINE SW IN) IN TO MONITOR L/R  
28dB ST LINE IN TO MONITOR L/R  
48dB MIC 3/4(XLR) IN TO REC L/R  
• Remove the accessory compartment cover by turning the quarter turn screw counterclockwise towards the  
RELEASE position, and remove the included speaker cables.  
• Switch the XP510i’s Power switch to the ON position.  
• Play your guitar or keyboard and slowly raise the channel control and the MASTER level control until you have  
reached the desired VOLUME.  
Introduction  
Configuring the XP510i for Transport  
Input Specifications  
Thank you for purchasing the Expedition XP510i PORTABLE PA SYSTEM from Samson! The XP510i features a com-  
pact, 10-channel mixer with 500 watts of onboard power and dual 2-way speakers, making it an ideal solution for  
a variety of small to medium sized PA applications. The XP510i is extremely portable thanks to its lightweight and  
unique “Slide and Lockdesign.  
You can easily carry your sound system using the XP510i’s “Slide and Lockfeature. The “Slide and Lockspeaker  
enclosures allow you to connect both speakers together into a single, easy to carry unit. Follow these steps to  
configure the XP510i for easy transport.  
Input Connector  
Input Impedance  
Nominal Source  
Impedance  
Rated Input Level  
Connector Type  
CH MIC  
3.6 kΩ / 7.5 kΩ  
50 ~ 600 Ω / 600 Ω  
-32 dBu / -22dBu  
XLR Type Balanced  
/ Phone Jack (TRS)  
T=Hot R=Cold  
S=GND  
The 10-channel mixer can be removed from the speaker for tabletop use. It features 4 inputs for connecting micro-  
phones, plus three inputs for connecting stereo signals, like those from a CD player or electronic keyboard. There’s  
also a built-in, 24-bit digital effects processor to add studio quality effects to your voice or instruments. For music  
playback, the XP510i features a convenient iPod dock. The mixer also provides a robust output, with 500 watts of  
total power from the lightweight, Class D amplifier section. The XP510i employs a matched speaker system with  
dual 2-way enclosures that have proprietary 10-inch woofers and 1-inch high frequency drivers. To help project  
the sound to a larger audience, the XP510i speakers can be mounted on standard speaker stands, thanks to the  
integral pole mount receptacles. The XP510i is constructed using durable ABS, high impact plastic, making it super  
road tough, and at the same time, lightweight.  
1. Place one speaker on the floor and set it on its side.  
3. Slide the second speaker into the speaker on the  
floor making certain that the two speakers stay parallel  
to each other.  
• Replace the accessory panel by aligning the bottom of the panel into the slots, make sure the quarter turn screw  
is in the RELEASE position; then close the panel and turn the quarter turn screw clockwise to LOCK.  
CH LINE  
3.6 kΩ / 7.5 kΩ  
50 ~ 600 Ω / 600 Ω  
-6 dBu / +4 dBu  
XLR Type Balanced  
/ Phone Jack (TRS)  
T=Hot R=Cold  
S=GND  
• Position the speakers on the floor or on stands, and using one of the included speaker cables, connect the mixer’s  
LEFT SPEAKER OUT to the left speaker’s input connector. Next, use the second included speaker cable to connect  
the RIGHT SPEAKER OUT to the right speaker’s input connector.  
STEREO INPUT  
STEREO INPUT  
10 kΩ  
10 kΩ  
600 Ω  
600 Ω  
0 dBu  
0 dBu  
Unbalanced Phone  
Jack  
In this manual, you’ll find a detailed description of the features of the XP510i PA system, as well as a description of  
its front and rear panels, step-by-step instructions for its setup and use, and full specifications. You’ll also find a war-  
ranty card enclosed—please don’t forget to fill it out and mail it in so that you can receive online technical support,  
and so we can send you updated information about these and other Samson products in the future. Also, be sure  
RCA pin Jack  
2. Position the second speaker above the first speaker  
and line up the “Slide and Locktracks and grooves so  
that they are parallel to the speaker on the floor.  
4. You will feel a slight click when the two speakers are  
Output Specifications  
Rated Output  
in place.  
Output Connector Output Impedance  
Nominal Load  
Impedance  
Connector type  
Level  
With proper care and adequate air circulation, your XP510i will operate trouble free for many years. We recommend  
you record your serial number in the space provided below for future reference.  
MONITOR L/R  
1 kΩ  
≥10 kΩ  
+4 dBu  
Phone Jack (TRS)  
Impedance bal-  
anced T=hot R=Cold  
S=ground  
Serial number:_______________________________  
Date of purchase:____________________________  
REC OUT  
600 Ω  
≥10 kΩ  
8 Ω  
+4 dBu  
250 W  
RCA pin Jack  
Phone Jack  
Should your unit ever require servicing, a Return Authorization number (RA) must be obtained before shipping  
your unit to Samson. Without this number, the unit will not be accepted. Please call Samson at 1-800-3SAMSON  
(1-800-372-6766) for a Return Authorization number prior to shipping your unit. Please retain the original packing  
materials and if possible, return the unit in the original carton and packing materials. If you purchased your Sam-  
son product outside the United States, please contact your local distributor for warranty information and service.  
SPEAKER OUTPUT  
*Specifications and design subject to change without notice  
Speaker cabinets must be reversed with respect to top and  
bottom.  
Using a Microphone  
• Be sure that the XP510i’s Power switch is set to the OFF position.  
• Turn all of the channel VOLUME (VOL) controls fully counterclockwise to the “0position.  
• If the speakers are not connected, connect the speaker wires as described in the previous section.  
• Next, connect the power cable to an AC outlet.  
Features  
XP510i Wiring Guide  
There are several ways to interface the XP510i to support a variety of applications. The XP510i features balanced  
inputs and outputs, so connecting balanced and unbalanced signals is possible.  
Dimensions  
• The XP510i is a compact PA system with dual 2-way speakers, onboard mixer and 500 watt power amplifier.  
CONNECTING THE XP510i  
301  
320  
• The XP510i is the ultimate in portable design. The lightweight and clever design allow you to connect all the  
pieces together into a single, easy to move case.  
• Using a standard XLR cable, plug a microphone into the XP510i’s Channel 1 MIC INPUT.  
Unbalanced 1/4” Connector  
173  
88  
• The mixer is stored in one of the speaker cabinets; the other cabinet has an accessory compartment for storing  
the speaker cables, microphones, etc.  
• The speakers are 2-way vented enclosures with 10-inch woofers for deep bass, complimented by a 1-inch high  
frequency driver, set in a custom horn with a 60 x 90 degree coverage pattern producing a clean, clear sound.  
• The internal 2 x 250 watt lightweight Class D power amplifier produces a powerful stereo sound.  
Balanced TRS 1/4” Connector  
• The XP510i’s mixer can be removed from the speaker for tabletop use and you can use the kick stand to set the  
mixer at an ergonomically correct angle.  
• The 10-channel mixer features four Mic/Line inputs allowing you to connect microphones or line signals, plus  
three stereo inputs for connecting line signals from keyboards, drum machines and MP3/CD players. You can  
engage the Phantom Power switch if you are using condenser microphones.  
• On each of the mixer’s channel inputs there is a Bass and Treble control allowing you to equalize the tone of the  
individual inputs.  
XLR Balanced Wiring Guide  
• To create a lush sound on any of the microphone channels, you can select from the ten, onboard, 24-bit digital  
effects.  
• Switch the XP510i’s Power switch to the ON position.  
• Set the MIC/LINE switch to the MIC position.  
• The XP510i features a built-in iPod dock allowing you to easily connect most iPod models for seamless music  
playback. You can use the iPod to simply play music, add background tracks, or repeat a commercial message at a  
fair or trade show.  
• Set the Channel 1 VOLUME (VOL) control to about halfway.  
• For added flexibility, the XP510i’s mixer has a Monitor Out on two, 1/4 inch jacks allowing you to connect to exter-  
nal powered monitor speakers.  
• While speaking into the microphone, slowly raise the MASTER level control until you have reached the desired  
level.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ratoc Systems Computer Drive SMA03U User Guide
Raypak Swimming Pool Heater 207A User Guide
Robotis Automobile Electronics RX 28 User Guide
Roland Musical Instrument KR105 User Guide
Rosewill Computer Drive RHUB120 User Guide
Rosewill Computer Drive RNX B100 User Guide
Samsung Cell Phone 010505D5 User Guide
Samsung DVD Player V6500K User Guide
Schumacher Battery Charger 100 Amp User Guide
Seiko Watch 5J22 User Guide