Large IR Vandal Dome Cameras
Manual
Model No.
NTSC
Resolution
Lens
# of IR LEDs
EV-2186-NKEQ
EV-2786-NKEQ
420 TV Lines
540 TV Lines
2.8~11mm
2.8~11mm
18
18
PAL
EV-2186-PKEQ
EV-2786-PKEQ
420 TV Lines
540 TV Lines
2.8~11mm
2.8~11mm
18
18
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Download from Www.Somanuals.com. All Manuals Search And Download.
SECO-LARM Large Vandal Dome Cameras
Overview:
Mounting screws
Female BNC
connector
Conduit cap
Set screws
Zoom
Focus
DC plug with
terminal block
DC jack
Important:
Do not cut the DC jack or the female BNC
connector as this will void the warranty.
Adjusting the
Camera Angle
Move the camera along
its 3 axes to adjust the
pan, tilt, or rotation.
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
6. Do not open or disassemble the camera. There are no
field-serviceable parts inside.
2. Use the camera within given temperature and
electrical limits.
7. Do not drop the camera or subject it to strong
vibrations.
3. Do not aim the LEDs directly at the eyes when the LEDs
are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
1Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-Gaussing, which occurs automatically with
many monitors when turning on.
5. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals1.
Installation:
1. Run hidden cables from the video source and 12VDC
power supply and connect to the camera. Do not cut
the DC jack or the female BNC connector as this will
void the warranty. If needed, use the included
SECO-LARM DC plug with terminal block.
If the installation involves surface wiring, remove the
conduit cap using a screwdriver and run wires
through the hole.
6. Mount the mounting base to the wall using the 4
included mounting screws. If necessary, use the
included screw anchors.
2. Test to make sure the voltage from the power supply is
correct. Use only 12VDC.
7. Adjust the camera angle as shown above.
8. Test the video signal.
9. To adjust zoom and focus, loosen the lock knobs by
hand or with a screwdriver. Slide left or right to
adjust. Do not use power tools. Lens damage
may result.
10. Reattach the dome to the camera using the included
allen wrench to tighten the set screws.
11. Do a final test of the video camera and monitor.
3. Undo the 4 set screws on the side of the dome cover
using the included allen wrench and remove the dome
from the base.
4. If mounting outdoors, apply the rubber seal to the base
as shown on page 2, Applying the Rubber Seal.
5. Hold the camera against the wall, ceiling, or other
mounting surface while watching the monitor to find the
best mounting location. Mark that location with a pencil.
SECO-LARM U.S.A., Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECO-LARM Large IR Vandal Dome Cameras
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
Change the position of the camera.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
Check that the correct power supply is in use.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
E-mail: [email protected]
PICSN4
MiEV-2x86-xKEQ_1011.docx
4
SECO-LARM U.S.A., Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|