Model iP27
The Portable System
For Your iPhone & iPod
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Quick Start.................................................................................................................................................................... 1
Controls and Indicators / iP27 Display .................................................................................................................... 2
Using the iP27........................................................................................................................................................... 3-4
Replacing iP27 Backup Batteries ............................................................................................................................. 5
Install/Replace Batteries for Portable Use .............................................................................................................. 5
Using The Remote Control Unit ............................................................................................................................... 6
A Consumer Guide to Product Safety.........................................................................................................................7
Troubleshooting ...................................................................................................................................................... 8-9
Solucionando problemas .....................................................................................................................................10-11
Warranty Information ................................................................................................................................................12
Maintenance
Maintenance
•
•
Place the unit on a level surface away from sources of direct sunlight or excessive heat.
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should
be placed between it and the furniture.
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzene, thinner
or similar materials can damage the surface of the unit.
•
FCC Information
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits
provide reasonable protection against radio and TV interference in a residential area.
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate
interference you can try one or more of the following corrective measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the radio or TV.
Use outlets on different electrical circuits for the equipment and the radio or TV.
Consult your dealer or an experienced radio/television technician if the problem still exists.
Modifying or tampering with your system’s internal components can cause a malfunction and might invalidate the
system’s warranty and void your FCC authorization to operate it.
This Class B digital apparatus complies with Canadian ICES-003.
Download from Www.Somanuals.com. All Manuals Search And Download.
iP27 Quick start
1: AC power
2: batteries
3: inserts
RESET
R E S T
Select the dock insert for your
iPhone or iPod model from the
table below and place insert in
Attach AC adaptor cable to jack
on back of the iP27 and plug the
other end into a wall socket to
play and charge iPhone/iPod
For portable operation, open
battery compartment on the bottom
of the unit. Insert 4
dock.
Never
dock
an
iPhone/iPod
without
the
“AA” (LR6) batteries as indicated.
proper insert in place.
touch 2G
insert 16
nano 4G
insert 17
iPhone 3G
insert 15
Use this insert
nano 4G
iPod touch
For this iPhone/iPod
3G iPhone
NOTE: If you do not have an insert for your iPhone/iPod, please
to purchase one.
4: iPhone/iPod
Insert an iPhone or iPod into the dock
(iPhone/IPod must not be in a “skin” or
case). iPhone/iPod will charge while
docked. Press the play Button on the
iP27 to play your iPhone/iPod.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Controls and Indicators
Universal Dock
Sleep / Minute Set Button
minute
sleep
time set
Time Set Button
Alarm On-Off
/Set Button
hour
minute
sleep
time set
hour
Hour Set Button
OFF
EXB Button
alm. reset
iPod
snooze/dimmer
Volume Down Button
Volume Up Button
Alarm Reset/
Power Off Button
OFF
snooze
iPod Play/Pause
Power ON Button
Snooze/Dimmer Button
DST Switch
Back of Unit
/off/remote
lock
line in
Line in Jack
DC Jack
Travel Lock/Remote Switch
iP27 Display
Time/Alarm Display
PM Indicator
EXB Indicator
DST Indicator
Alarm Armed
iPod Indicator
Sleep Display
Main Battery Low Indicator
Travel Lock Indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock Backup Battery Low Indicator
2
Using the iP27
Connect iP27 to Power Source
a) For home operation and to charge your iPhone or iPod, plug the AC adaptor cable into the AC Adaptor Jack and the other end
into a standard 120VAC wall socket. Adaptor must be plugged in to charge iPhone/iPod.
b) For portable operation, install 4 “AA” (LR6) batteries, 2 in each compartment on the bottom of the unit. Make sure polarity matches
diagram in compartments.
Setting the Clock
a) Depending on your location and the time of year, move the
(Daylight Saving Time) switch located inside the left battery
compartment on the bottom of the unit to +1 to add one hour (a DST icon will appear on the display) or to -1 to subtract 1 hour.
b) Press and hold the Time Set Button until the display flashes. Press the
Button to toggle between 24 hour (military) and 12
hour (standard) time display modes.
c) Press the Hour Button to adjust the hour setting (a PM indicator appears when time is set to PM; there is no AM indicator)
d) Press the Minute Button to adjust the minute setting. When the correct time is displayed, press the Time Set Button again. Two
beeps will indicate clock setting is complete.
Using the Alarm
Setting the Alarm
a) Press and hold the
is detected).
Button until the alarm time flashes to wake to iPhone/iPod (buzzer alarm sounds if no iPhone or iPod
b) Press the Hour Button to set the desired alarm hour (a PM indicator appears when time is set to PM; there is no AM indicator)
c) Press the Minute Button to set the alarm minute time. When the desired alarm time is displayed, press the
Two beeps will indicate alarm setting is complete. Alarm is now armed, indicated by the alarm clock icon.
Arming and Disarming Alarm (Turn Alarm Function ON and OFF)
Button again.
a) Press the
Button to arm or disarm alarm functions. When armed, the alarm icon appears in the display.
Resetting the Alarm to Come on the Next Day
a) When the alarm is sounding, press the OFF Button to stop the alarm and reset it to come on the following day.
Snooze
a) Press the Snooze Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes later. Snooze can be
pressed several times during the 1 hour alarm cycle.
Sure Alarm
The iP27 has a sure alarm feature: if the backup battery is installed, the buzzer alarm will still sound in the event of power failure.
iPhone/iPod
Playing and charging your iPhone or iPod
a) After selecting and placing the proper insert for your iPhone or iPod model, gently dock iPhone/iPod in Dock. When docked, the
iPhone or iPod will charge until fully charged when the iP27 is connected to an outlet with AC adaptor. Unit will not overcharge
iPhone/iPod.
b) Press the
c) Press or
Button to play iPhone/iPod, and again to pause.
Button to adjust iP27 volume up or down.
e) Press OFF Button to turn iP27 and iPhone/iPod off.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the iP27
Using Sleep Mode
•
Press the Sleep Button while the iPhone/iPod is playing to enter sleep mode, and continue to press to step through the
available sleep times: 90, 60, 30 or 15 minutes. The will appear on the display. The iP27 will play for the number of
minutes set, growing gradually softer until shutting off both the unit and the iPhone/iPod at the set time. Press the Volume
Up or Down controls to set your own sleep volume. Sleep volume setting is separate from your alarm or regular listening
volume selection.
Using the Line-in Jack
•
iP27 Line-in Jack (one end in the device’s line out or headphones jack, the other in the iP27 line in jack). Make sure there is
no iPod docked in the iP27 when using the line-in jack. Press the
iPod Play Button.
Using Dimmer
•
Press the Snooze/Dimmer Button during normal operation to adjust the brightness of LCD display. While operating on AC
current, the switch will toggle between high, medium, low and off settings. In battery mode, the display is off by default. Press
once to activate the display for about 3 seconds.
Using the Travel Lock
•
You can disable the iP27 controls to avoid turning on the device or changing settings while in transit and to save battery life
during extended periods of non-use. To do so, move the Switch (located on the back of the unit) to the Locked icon
position. A Lock Icon will appear on the display indicating the unit is locked and controls are inactive. Move the switch to
the Remote position to restore normal function with remote control capability, or to the Off position to restore function with the
remote disabled.
Using the EXB Button
•
Press the
Button located on the right side of the unit to enable the EXB sound enhancement circuitry. This circuitry is
designed to provide a broader audio image with enhanced low range sound reproduction and UPRO Wide Stereo to bring
added life to compressed MP3 files. The EXB icon will appear in the display when EXB is active. Press switch again to disable
the EXB effect.
UPRO Wide Stereo is based on UPRO technology. UPRO is a Beautiful Enterprise Co Ltd registered
trademark.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing iP27 Backup Battery
Install/Replace Backup Battery
Battery install for
Clock display back up
The iP27 uses a backup battery system to provide continuous alarm operation and
clock settings in the event of a power failure. If the Backup Battery Low Icon located
on the left of the display is flashing, it is time to replace the backup battery. Please
make sure the AC adaptor is connected, otherwise all settings may be lost during
battery replacement.
Open the battery compartment cover located on the bottom of the unit in the left
battery compartment. Insert 1 “CR2032” battery as indicated. Replace battery
compartment covers.
Install/Replace Batteries for Portable Use
The iP27 uses 4 “AA” (LR6) batteries for portable playing. If sound becomes weak
or distorted while operating on batteries, it’s time to replace the batteries.The iP27
will not charge your iPhone or iPod while operating on batteries.
•
•
Open the battery compartment covers located on the bottom of the unit.
Insert 2 AA (LR6) batteries in each compartment as indicated, making sure the
polarity (+ and -) matches the diagram.
•
Replace battery compartment covers.
Batteries information:
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium)
batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using The Remote Control Unit
Install/Replace the Remote Control Battery
The remote control battery is already installed at the factory. When the remote control
stops operating or its range seems reduced, replace the battery with a new one.
1. The battery door is located on the back end of the unit.
2. Slide the battery door to release the battery door latch and remove the battery door.
3. Insert a “CR2032” 3-volt lithium battery. Make sure the polarity (the + and – side of
the battery) is correct.
4. Replace the battery compartment door back in the remote control.
NOTE: PLEASE DISCARD BATTERIES PROPERLY
Operating the remote control
The Remote Control controls basic functions on the iP27 and certain iPhone/iPod functions when the iPhone/iPod is docked
in the iP27. For best results, aim remote control towards the remote sensor by the lower right corner of the display.
Move the
Switch to Remote position to enable the remote control.
alm. reset
OFF
Turns iP27 OFF or resets alarm when alarm is sounding
Volume Buttons raise and lower volume on the unit.
Skip to previous or next track when iPod is playing, or
hold to scan current playing track.
Selects iPhone/iPod and plays track. In play mode, press to pause
sleep
mute
Selects Sleep Time function
Turn EXB sound enhancement ON or OFF
Toggles sound ON or OFF
snooze
Snooze mode when alarm sounds, otherwise dims display
Download from Www.Somanuals.com. All Manuals Search And Download.
6
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions
carefully before installation and use, and keep these instructions handy for future reference. Take special note of all
warnings listed in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also,
it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air
through the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the
unit to where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for
cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any
openings or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent
damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A.
B.
C.
D.
the power supply cable or plug has been damaged.
objects have fallen into or liquid has been spilled into the enclosure.
the unit has been exposed to rain.
the unit has been dropped or the enclosure damaged.
E.
the unit exhibits a marked change in performance or does not operate normally.
12. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the
power cable should be unplugged and batteries removed from the unit to prevent damage or corrosion.
13. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service
personnel.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Possible Problem
Solution
Unit doesn’t respond
(no power)
AC adaptor isn’t plugged into a wall outlet
or the connector is not plugged into the
power supply jack on the back of the unit
Plug the AC adaptor into a wall outlet and plug the
connector into the supply jack on the unit
Wall outlet is not functioning or switched off Plug another device into the same outlet to confirm the outlet
is working. Make sure any associated power switch is ON
Batteries are weak or dead
Replace with new batteries
Make sure the dock insert is the one for for your iPhone/iPod
iPhone/iPod
does not dock
properly
Using no or wrong insert
Remove your iPhone/iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPod. Make sure there is no “skin” or case on the iPod.
Then reseat it in the dock.
iPhone/iPod not docked properly
Battery Low icon
always flashing
Batteries are weak
Replace with new batteries
Batteries were not installed properly
Check to make sure the polarity ( + and – ends) matches
the diagram in the battery compartment
Remove your iPhone/iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPhone/iPod. Then reseat it in the dock.
iPhone/iPod does
not respond to the
unit
iPhone/iPod is not docked properly
Your iPod software is too old
iPhone/iPod is locked up
Upgrade software on your iPod via iTunes
Please make sure your iPod is working properly before
docking into the unit. You may need to reset your
iPhone/iPod. Please refer to your manual for details.
Using 1st or 2nd generation iPod, iPod
shuffle or other devices.
iP27 cannot control those iPod models or other devices.
Buttons/Controls
don’t work
Move Travel Lock to Off or Remote position
Press the Menu button on your iPod
Travel Lock is in Lock position
If your iPod is not used for some time, it
may enter deep sleep mode
iPhone/iPod does not
come on immediately
iPhone/iPod battery is too run down/weak
Charge your iPhone/iPod for about 5 minutes
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Troubleshooting
Symptom
Possible Problem
Solution
Make sure the iP27 is plugged into a working AC outlet to
charge your iPhone or iPod
iPhone/iPod didn’t
charge
Operating iP27 on batteries. The iP27 only
charges iPhone/iPod while operating on AC
power
Remove your iPhone or iPod from the dock and check for
obstruction on the connectors in the dock and on your
iPhone or iPod. Then replace it in the dock.
iPhone or iPod is not docked properly
Please make sure your iPhone or iPod is working properly
before docking into the unit. It may need a reset. Please
refer to your iPhone or iPod manual for details.
iPhone/iPod is locked up/ frozen
iPhone/iPod battery has problem
Volume level is set too high
Sound is distorted
Decrease the volume
If the original sound source (MP3) is of poor quality,
distortion and noise are easily noticed with high-power
speakers. Try a different audio source such as a music CD.
Sound source is distorted
If you are using an external sound source like older
generation of iPod, try reducing the output volume on the
device itself.
Try turning off EXB on the unit or the bass boost OFF on
your iPod/sound source.
Batteries are weak
Replace current batteries with new ones
Remote Control is not pointed toward
the iP27 remote sensor or sensor is
blocked
Remote Control
didn’t work
Point the Remote Control toward the iP27, move within 10
feet of the unit, make sure sensor is unobstructed
Battery weak
Replace current battery with new battery
Move Travel Lock switch to Remote position
Travel Lock is in Lock or Off position
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Solucionando problemas
Síntoma
Causa
Solución
El adaptador de AC no está conectado al
Conecte el adaptador de AC al tomacorriente y también
La unidad no
funciona (no circula
corriente eléctrica)
tomacorriente o el conector no está conectado conecte el conector a la ficha en la parte posterior de la
a la ficha en la parte posterior de la unidad
El tomacorriente no funciona
unidad
Coloque otro aparato en ese mismo tomacorriente para
confirmar si el que no funciona es el tomacorriente
Las baterías están gastadas
Reemplace las baterías
No ha colocado el encastre del iPod, o está
utilizando el encastre incorrecto.
El iPod no encastra
correctamente
Verifique que el encastre sea el apropiado para su iPod
El iPod no encastra correctamente
Quite el iPod del encastre y retire la posible obstrucción
del encastre o de su iPod. Vuelva a colocar el iPod dentro
del encastre.
El ícono de batería
baja está destellando
Las baterías están gastadas
Reemplace las baterías
Las baterías no están instaladas
correctamente
Verifique que la polaridad de las baterías (- y +) se encuentren
de acuerdo al diagrama del compartimiento de baterías.
El iPod no se
comunica con la
unidad
El iPod no está instalado correctamente
Quite el iPod del encastre y verifique posibles
obstrucciones del encastre o de su iPod. Vuelva a colocar
el iPod dentro del encastre.
Su software es obsoleto
Renueve su software. Para mayor información, diríjase a
El iPod no responde
Verifique que su iPod funcione correctamente antes de
conectarlo a la unidad. Refiérase al manual de su iPod
para más detalles.
Usted tiene un iPod de primera o segunda
generación, un nano u otro tipo de aparato
El iP27 no puede controlar estos otros aparatos
Los botones/controles
no funcionan
La Traba de viaje se encuentra en
la posición “ON” (trabada).
Corra la traba a la posición “OFF” (destrabada)
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Solucionando problemas
Síntoma
Causa
Solución
El iPhone/iPod no
carga
El iPhone/iPod no está instalado
correctamente
Quite el iPhone/iPod del encastre y retire la posible
obstrucción del encastre o de su iPhone/iPod. Vuelva a
colocar el iPod dentro del encastre.
El iPhone/iPod está trabado/no responde
Por favor asegúrese de que su iPhone/iPod funcione
correctamente antes de colocarlo en el encastre. Refiérase
al manual de su iPhone/iPod para mayor información.
La batería del iPod podría tener algún
inconveniente
El sonido sale
distorsionado
El volumen se encuentra muy alto
Baje el volumen
El sonido sale distorsionado de la unidad
Si el sonido original de su iPhone/iPod era de pobre calidad,
las distorsiones y ruidos se harán más notables con los
parlantes de alta potencia. Pruebe utilizar otra fuente de
audio como un CD.
Si está utilizando un iPod de primeras generaciones o un
nano, intente bajar el volumen de su aparato. También
intente apagar el amplificador de bajos
El control remoto no
funciona
Las baterías están gastadas
Reemplace las baterías por nuevas
No está apuntando el control remoto
hacia el iP27
Apunte el control remoto hacia el iP27 y manténgase a
una distancia máxima de 10 pies de la unidad.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
|