OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
3/8 in. DRILL
PERCEUSE 10 mm (3/8 po)
TALADRO DE 10 mm (3/8 pulg.)
D46C
Your drill has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Su taladro ha sido diseñada y fabricada de conformidad con las
estrictasnormasparabrindarfiabilidad,facilidaddeusoyseguridad
para el operador. Con el debido cuidado, le brindará muchos años
de sólido y eficiente funcionamiento.
Votreperceuseétéconçueetfabriquéeconformémentànosstrictes
normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.
Correctement entretenue, elle vous donnera des années de
fonctionnement robuste et sans problème.
ADVERTENCIA: Para reducir el riesgo de lesiones,
el usuario debe leer y comprender el manual del operadorantes
de usar este producto.
AVERTISSEMENT : Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre le
manuel d’utilisation avant d’employer ce produit.
Le agradecemos su compra.
Merci de votre achat.
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
Avoid accidental starting. Be sure switch is off
WARNING:
before plugging in. Carrying tools with your finger on
the switch or plugging in tools that have the switch on
invites accidents.
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
TOOL USE AND CARE
ELECTRICAL SAFETY
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your appli-
cation. The correct tool will do the job better and safer
at the rate for which it is designed.
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Double insulation
eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
Do not use tool if switch does not turn it on or off. Any
tool that cannot be controlled with the switch is dangerous
and must be repaired.
Disconnect the plug from power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL SAFETY
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of con-
trol and deterioration of the enclosure plastic.
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
ꢁ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
When servicing a tool, use only identical replacement
SERVICE
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of
shock or injury.
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the cutting
tool “live” and shock the operator.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 16 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 100 feet is not recom-
mended. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT safety
glasses. Following this rule will reduce the risk of serious
personal injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
If the power supply cord is damaged, it must be re-
placed only by the manufacturer or by an authorized
service center to avoid risk.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this product. If
you loan someone this product, loan them these instruc-
tions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
ꢂ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Power
Watt
min
Minutes
Time
Alternating Current
Direct Current
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
n
o
No Load Speed
Class II Construction
Per Minute
.../min
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
To reduce the risk of injury or damage, avoid contact with any hot
surface.
Hot Surface
ꢃ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNING:
CAUTION
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to the nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand com-
pletely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Ryobi customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
ꢄ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-
wire grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” on the cord’s jacket.
The double insulated system is intended to protect the
user from shock resulting from a break in the product’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
NOTE:Servicingofaproductwithdoubleinsulationrequires
extreme care and knowledge of the system and should be
performedonlybyaqualifiedservicetechnician. Forservice,
wesuggestyoureturntheproducttoyournearestauthorized
service center for repair. Always use original factory replace-
ment parts when servicing.
**Ampere rating (on product data plate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
ELECTRICAL CONNECTION
100'
This product has a precision-built electric motor. It should
be connected to a power supply that is 120 volts, AC only
(normal household current), 60 Hz. Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools, or other obstructions while you are working with
a power tool. Failure to do so can result in serious per-
sonal injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use product with a damaged
cord since touching the damaged area could cause elec-
trical shock resulting in serious injury.
ꢅ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Chuck.......................................................................3/8 in.
Switch.............................Variable Speed Reversible (VSR)
Clutch............................................................. 24 Positions
No Load Speed .................................0-1,100 r/min. (RPM)
Input ...................................... 120 V, AC only, 60 Hz, 4.5 A
Net Weight.............................................................. 3.8 lbs.
BIT STORAGE
TORqUE
ADjUSTmENT RING
KEYLESS
CHUCK
DIRECTION OF
ROTATION SELECTOR
(FORWARD/REVERSE)
SWITCH
TRIGGER
LOCK-ON
BUTTON
Fig. 1
KNOW YOUR DRILL
KEYLESS CHUCK
See Figure 1.
The keyless chuck allows you to hand-tighten or release
the drill bit in the chuck jaws.
The safe use of this product requires an understanding of the
information on the product and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
LOCK-ON BUTTON
The lock-on button is convenient for continuous drilling for
extended periods of time.
TORQUE ADJUSTMENT RING
Your drill has a 24-position clutch. The torque adjustment
ring can be turned to select the right amount of torque for
your application.
BIT STORAGE
Bits provided with the drill can be placed in the storage
area, located on the top of the drill.
DIRECTION OF ROTATION SELECTOR
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
with increased trigger pressure and lower speed with
decreased trigger pressure.
(FORWARD/REVERSE)
Your drill has a direction of rotation (forward/reverse) selector
located above the switch trigger for changing the direction
of bit rotation.
ꢆ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
WARNING:
Do not discard the packing material until you have care-
Do not attempt to modify this product or create acces-
sories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Drill
Double Ended Bits (ꢀ)
Operator’s Manual
Case
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
OPERATION
SWITCH TRIGGER
See Figure 2.
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
To turn the drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch delivers higher speed and torque
with increased trigger pressure and lower speed with
decreased trigger pressure.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
NOTE: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned; this is a normal
part of the switch function.
DIRECTION OF
ROTATION SELECTOR
WARNING:
LOCK-ON
BUTTON
FORWARD/REVERSE
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
REVERSE
APPLICATIONS
You may use this product for the purposes listed below:
Drilling in all types of wood products (lumber, plywood,
paneling, composition board, and hardwood)
Drilling in ceramics, plastics, fiberglass, and laminates
Drilling in metals
FORWARD
SWITCH TRIGGER
Mixing paint
Fig. 2
ꢇ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE)
See Figure 2.
UNLOCK
(RELEASE)
CHUCK
jAWS
CHUCK BODY
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch trigger
for drilling. The drilling direction is reversed when the selector
is to the right of the switch trigger.
CAUTION:
To prevent gear damage, always allow the chuck to
come to a complete stop before changing the direction
of rotation.
LOCK
(TIGHTEN)
CHUCK
COLLAR
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
Fig. 3
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
BIT STORAGE
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool the
drill by running it without a load and at full speed.
KEYLESS CHUCK
See Figure 3.
The drill has a keyless chuck that makes it simple to
tighten or release drill bits in the chuck jaws. Grasp and
hold the collar of the chuck with one hand. Rotate the chuck
body with your other hand. The arrows on the chuck indicate
which direction to rotate the chuck body in order to LOCK
(tighten) or UNLOCK (release) the drill bit.
WARNING:
Do not hold the chuck body with one hand and use the
power of the drill to tighten the chuck jaws on the drill
bit. The chuck body could slip in your hand, or your hand
could slip and come in contact with the rotating drill bit.
This could cause an accident resulting in serious personal
injury.
Fig. 4
BIT STORAGE
See Figure 4.
When not in use, bits provided with the drill can be placed
in the storage area located on the top of the drill.
WARNING:
INSTALLING BITS
See Figure 5 - 6.
Always unplug the tool when installing or remov-
ing bits, adjusting settings, or when the tool is
not in use. Failure to unplug the tool may result
in accidental starting and serious personal injury.
Unplug the drill.
Open or close the chuck jaws to a point where the open-
ing is slightly larger than the bit size you intend to use.
Also, raise the front of the drill slightly to keep the bit from
falling out of the chuck jaws.
Insert the drill bit.
10 − English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
UNLOCK
(RELEASE)
WARNING:
CHUCK
jAWS
CHUCK BODY
Make sure to insert the drill bit straight into the chuck
jaws. Do not insert the drill bit into the chuck jaws at
an angle then tighten, as shown infigure 6. This could
cause the drill bit to be thrown from the drill, resulting in
possible serious personal injury or damage to the
chuck.
Tighten the chuck jaws securely on the bit.
DRILL BIT
NOTE: Rotate the chuck body in the direction of the ar-
row marked LOCK to close the chuck jaws. Do not use
a wrench to tighten or loosen the chuck jaws.
LOCK
(TIGHTEN)
REMOVING BITS
See Figure 5.
CHUCK
COLLAR
Unplug the drill.
RIGHT
Fig. 5
Open the chuck jaws.
NOTE: Rotate the chuck body in the direction of the arrow
marked UNLOCK to open the chuck jaws. Do not use a
wrench to tighten or loosen the chuck jaws.
Remove the drill bit.
LOCK-ON BUTTON
See Figure 7.
This drill is equipped with a lock-on feature, which is
convenient for continuous drilling for extended periods of
time. To lock-on:
Depress the switch trigger.
Push in and hold the lock-on button, located on the side
of the handle.
Release the switch trigger.
Release the lock-on button and the drill will continue
WRONG
running.
To release the lock, depress and release the switch trigger.
Fig. 6
If the lock-on feature is engaged during use and the drill
becomes disconnected from the power supply, disengage
the lock-on feature immediately.
DIRECTION OF
ROTATION SELECTOR
(FORWARD/REVERSE)
LOCK-ON
BUTTON
WARNING:
Before connecting the drill to a power supply source,
always check to be sure it is not in lock-on position (de-
press and release the switch trigger). Failure to ensure
that it is not locked-on could result in accidental starting
of the drill resulting in possible serious injury. Do not lock
the switch trigger in applications where the drill may need
to be suddenly stopped.
SWITCH
TRIGGER
Fig. 7
11 − English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ADJUSTABLE TORQUE CLUTCH
TORqUE
ADjUSTmENT RING
See Figure 8.
TO DECREASE
TORqUE
This product is equipped with an adjustable torque
clutch for driving different types of screws into different
materials.Thepropersettingdependsonthetypeofmaterial
and the size of screw you are using.
ADJUSTING TORQUE
See Figure 8.
There are twenty-four torque indicator settings located on
the front of the drill.
Rotate the adjusting ring to the desired setting.
•
•
•
1 - 4
5 - 8
For driving small screws
For driving screws into soft material
TO INCREASE
TORqUE
9 - 12 For driving screws into soft and hard
materials
Fig. 8
•
•
•
13 - 16 For driving screws into hard wood
17 - 23 For driving large screws
For heavy drilling
DRILLING
See Figure 9.
Depress and release the switch trigger to be sure the drill
is in the OFF position before connecting it to a power
supply.
Check the direction of rotation selector for the correct
setting (forward or reverse).
Secure the material to be drilled in a vise or with clamps
to keep it from turning as the drill bit rotates.
Plug the drill into power supply. Hold the drill firmly and
place the bit at the point to be drilled.
Depress the switch trigger to start the drill.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force the drill or
apply side pressure to elongate a hole. Let the tool do
the work.
WARNING:
Be prepared for binding at bit breakthrough. When these
situations occur, the drill has a tendency to grab and kick
in the opposite direction and could cause loss of control
when breaking through material. If not prepared, this loss
of control can result in possible serious injury.
Fig. 9
When drilling hard, smooth surfaces, use a center punch
to mark the desired hole location. This will prevent the
drill bit from slipping off-center as the hole is started.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in the workpiece or if the drill stalls, stop
the tool immediately. Remove the bit from the workpiece
and determine the reason for jamming.
1ꢀ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Electrictoolsusedonfiberglassmaterial,wallboard,spackling
compounds, or plaster are subject to accelerated wear and
possible premature failure because the fiberglass chips and
grindings are highly abrasive to bearings, brushes, commu-
tators, etc. Consequently, we do not recommended using
this product for extended work on these types of materials.
However, if you do work with any of these materials, it is
extremely important to clean the product using compressed
air.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
LUBRICATION
All of the bearings in this product are lubricated with a suf-
ficient amount of high grade lubricant for the life of the unit
under normal operating conditions. Therefore, no further
lubrication is required.
1ꢁ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHUCK REMOVAL
See Figures 10 - 12.
mALLET
The chuck may be removed and replaced with a new one.
Unplug the drill.
Insert a 5/16 in. or larger hex key into the chuck of the
CHUCK
jAWS
drill and tighten the chuck jaws securely.
Tap the hex key sharply with a mallet in a clockwise di-
rection. This will loosen the screw in the chuck for easy
removal.
Open the chuck jaws and remove the hex key. Using a
screwdriver, remove the chuck screw by turning it in a
clockwise direction.
NOTE: The chuck screw has left hand threads.
Insert the hex key into the chuck and tighten the chuck
jaws securely. Tap sharply with a mallet in a counterclock-
wise direction. This will loosen the chuck on the spindle.
It can now be unscrewed by hand.
HEX KEY
KEYLESS
CHUCK
Fig. 10
TO RETIGHTEN A LOOSE CHUCK
The chuck may become loose on the spindle and develop
a wobble. Also, the chuck screw may become loose, caus-
ing the chuck jaws to bind and prevent them from closing.
To tighten:
Unplug the drill.
SCREWDRIVER
Open the chuck jaws.
Insert a hex key into the chuck and tighten chuck jaws
securely. Tap the hex key sharply with a mallet in a
clockwise direction. This will tighten the chuck on the
spindle.
Open the chuck jaws and remove the hex key.
Tighten the chuck screw.
Fig. 11
mALLET
HEX KEY
Fig. 12
1ꢂ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
1ꢃ − English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL / 3/8 in. DRILL
MANUEL D’UTILISATION / PERCEUSE 10 mm (3/8 po)
MANUAL DEL OPERADOR / TALADRO DE 10 mm (3/8 pulg.)
• PaRts anD sERVicE
Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the
product data plate.
D46C
• MODEL nUMBER ____________________
• sERiaL nUMBER ____________________
• HOw tO OBtain REPLacEMEnt PaRts:
Replacement parts can also be obtained at one of our Authorized Service Centers.
• HOw tO LOcatE an aUtHORizED sERVicE cEntER:
Authorized Service Centers can be located online at www.ryobitools.com or by calling 1-800-525-2579.
• HOw tO OBtain cUstOMER OR tEcHnicaL sUPPORt:
To obtain Customer or Technical Support please contact us at 1-800-525-2579.
RYOBI® is a registered trademark of Ryobi Limited used under license.
• PiÈcEs Et sERVicE
Avant de faire la demande de service ou l’achat de pièces de remplacement, veuillez obtenir le numéro de série du modèle à partir
de la plaque de données du produit.
D46C
•
•
nUMÉRO DE MODÈLE _____________________
nUMÉRO DE sÉRiE _____________________
• cOMMEnt OBtEniR LEs PiÈcEs DE REMPLacEMEnt :
Les pièces de remplacement peuvent être achetées en ligne sur le site www.ryobitools.com ou par téléphone au 1-800-525-2579.
Les pièces de remplacement peuvent être obtenues à un de nos centres de service autorisés.
• cOMMEnt tROUVER Un cEntRE DE sERVicE aUtORisÉ :
Les centres de service autorisés peuvent être localisés en ligne au www.ryobitools.com ou en téléphonant au 1-800-525-2579.
• cOMMEnt OBtEniR DE L’aiDE En cOntactant LE sERVicE À La cLiEntÈLE :
Pour contacter le service à la clientèle pour une question technique ou pour tout autre renseignement, veuillez nous téléphoner
au 1-800-525-2579.
Ryobi® est une marque déposée de Ryobi Limited utilisée sous licence.
• PiEzas DE REPUEstO Y sERViciO
Antes de solicitar servicio técnico o comprar piezas de repuesto, obtenga su modelo y número de serie de la placa de datos del
producto.
D46C
• nÚMERO DE MODELO _________________________
• nÚMERO DE sERiE _________________________
• cÓMO OBtEnER PiEzas DE REPUEstO:
Las piezas de repuesto se pueden comprar en nuestro sitio en la red mundial, en la dirección www.ryobitools.com o llamando al
1-800-525-2579. Las piezas de repuesto también se pueden obtener en uno de nuestros Centros de Servicio Autorizados.
• cÓMO LOcaLizaR Un cEntRO DE sERViciO aUtORizaDO:
Puede encontrar los Centros de Servicio Autorizados visitando nuestro sitio en la red mundial, en la dirección www.ryobitools.
com o llamando al 1-800-525-2579.
• cÓMO OBtEnER sERViciO O asistEncia tÉcnica aL cOnsUMiDOR:
Para obtener Servicio o Asistencia Técnica al Consumidor, sírvase comunicarse con nosotros llamando al 1-800-525-2579.
Ryobi® es una marca comercial registrada de Ryobi Limited y es empleada mediante autorización.
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625 • Phone 1-800-525-2579
États-Unis, Téléphone 1-800-525-2579 • USA, Teléfono 1-800-525-2579
983000-808
ꢅ-1ꢆ-0ꢆ (REV:0ꢀ)
Download from Www.Somanuals.com. All Manuals Search And Download.
|