INSTALLATION/OPERATION MANUAL
Q-750d Series
LED Home Theater Projector
and Digital High Definition (DHD™) Controller/Scaler/Processor
Q-750d
Q-750d/CineWide™
Q-750d/CineWide with AutoScope™
Download from Www.Somanuals.com. All Manuals Search And Download.
RuncoCare™ Standard Two Year Limited
Warranty
Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years
of unparalleled video performance.
This RuncoCare Standard Limited Warranty is provided free of charge by Runco International with the purchase of a covered
Runco product. The following sets forth Runco’s Standard Limited Warranty applicable to all Runco projectors, processors,
1
LCD and plasma display products, with the exception of the following models: XP-103DHD, SC-1, SC-1a and VW-100HD .
The following terms and conditions of the RuncoCare Standard Limited Warranty represent a contract between us, Runco
International and you, the customer who has purchased a Runco product. This contract applies to purchases of covered
Runco products occurring on or after September 1, 2008. Runco reserves the right to change the terms of this contract, and
such changes shall apply to purchases of covered Runco products that occur on or after any future effective date.
RuncoCare Standard Features
• Two-year protection from defects in material and workmanship
• Access to 24x7 phone support
• Complimentary, second-day one-way shipping
Warranty Coverage
Runco warrants its products to be free from defects in material and workmanship during the warranty period provided below.
If, in Runco’s determination, a product proves to be defective in material or workmanship during the warranty period, Runco
will repair the product, replace the product with a similar new or like new product, or refund a prorata share of the purchase
2
price (calculated based on the remainder of the warranty period and the thencurrent MSRP of a similar product), if repair or
replacement of the product is determined by Runco to not be feasible.
Length of Warranty
Runco products are warranted for two (2) years from the date of shipment from Runco. Lamps are warranted six (6) months
from the date of shipment or 1000 hours, whichever comes first. All other accessories, which includes, but is not limited to,
cables, remotes, carrying cases, lens cap and other peripherals sold with the Runco product, are warranted for ninety (90)
days from the date of shipment. Repaired product or replacement lamp is subsequently warranted for the remaining portion (if
any) of the original warranty term or 90 days from the date the product was shipped to you, whichever is longer.
Eligibility
This RuncoCare Standard Limited Warranty is valid only for the first customer who purchases the covered product from an
authorized Runco dealer or distributor. This warranty is not transferable. You may be required to provide proof of purchase in
order to receive warranty services.
1. Runco may update this list of products excluded from this warranty from time to time at Runco’s sole discretion, but updates to
the list of covered products will not apply on a retroactive basis.
2. MSRP is defined as the most recent product price listed on Runco’s price list.
Q-750d Series Installation/Operation Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
RuncoCare Claim Procedure
In the event of a product defect, please follow the warranty claim procedure provided below:
1. The Customer is required to contact a Runco dealer or Runco Technical Support via email at support@runco.com or via
in Europe for product service.
2. Be prepared to provide the date of purchase, the place of purchase, serial number, product model number, description of
the problem and troubleshooting steps already attempted.
3. Runco Technical Support staff will attempt to correct any minor issues that may be causing the problem. If Runco is
unable to fix the problem to the customer’s satisfaction, Runco will issue a Return Material Authorization (RMA) if it is
determined that the claim was made within the coverage period of the Standard Limited Warranty.
4. The customer will need to return the defective product to the Runco repair depot location specified by the Runco technical
support representative. The customer will need to properly package the defective product, consisting of the product only,
and not include any accessories (e.g., cables, remotes, carrying cases, lens, lens cap and other peripherals) and return it
to the Runco repair depot specified by the technical support representative. It is the customer’s responsibility to properly
package the hardware, include all appropriate materials, and return it to the location specified by the Runco technical
support department. The customer will need to address and resolve any shipping damage claims directly with the shipping
company.
5. The customer is responsible for providing a suitable box to ship the defective product to an authorized Runco repair depot.
Boxes may be purchased from a Runco technical support representative.
6. The customer is responsible for paying freight charges to ship the defective product to an authorized Runco repair depot.
7. Runco will pay freight charges to return the repaired/replacement product to the customer from the Runco repair depot.
8. Once an RMA has been created, the customer may contact serviceorders@runco.com for followup questions or
confirmation status of the claim process.
Warranty Exclusions
This RuncoCare Standard Limited Warranty does not include or is limited by the following:
1. Products not purchased from an authorized Runco dealer
2. Rental costs incurred by the customer in the event of product defect or failure
3. Any product with a defaced, modified, or removed serial number
4. Damage, deterioration, or malfunction resulting from:
a Accident, abuse, misuse, neglect, improper ventilation, fire, water, disaster, lightning, or other acts of nature, smoke
exposure (cigarette or otherwise), unauthorized product modification (including use of an unauthorized mount), or failure
to follow instructions supplied with the product
b Repair or attempted repair by anyone not authorized by Runco
c Any damage to the product due to shipment
d Removal or installation of the product
e Causes external to the product, such as electric power fluctuations or failure
f Use of supplies or parts not meeting Runco’s specifications
g Normal wear and tear
h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed
i
Customer caused defects, including but not limited to, scratched/defaced/altered plastics
iv
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
j
Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for
regular cleaning of the product
k Opening the product and/or tampering with internal circuitry
Products lost, stolen or discarded
l
m Any damage or dissatisfaction associated with latent images, “burnin,” or any other damage determined by Runco to be
the result of customer use patterns
n Any other cause, which does not relate to a product defect in material or workmanship
5. Removal, installation, and setup service charges are excluded from this Standard Limited warranty
6. Runco’s warranty does not cover black uniformity issues or other LCD issues associated with usage outside the Runco
recommended guidelines and specifications for the product
7. Second day shipment delivery time and availability may vary based on origin and destination and Runco is unable to deliver
to PO Box and FPO Box addresses
Extended Service Options
Runco offers extended and expanded service plans. For information on additional product protection, please email
serviceorders@runco.com or call (toll free) 800-23RUNCO (800-237-8626).
Online Product Registration
Limitation of Implied Warranties
RUNCO PROVIDES NO WARRANTIES, EXPRESS OR IMPLIED, EXCEPT THOSE EXPRESSLY PROVIDED HEREIN. RUNCO
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
Q-750d Series Installation/Operation Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Exclusion of Damages
RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT.
1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS,
LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR
OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
2. RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR OTHERWISE.
3. RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of Local Law
This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities
do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the
above limitations and exclusions may not apply to you.
COPYRIGHT AND TRADEMARKS:
© Copyright 2009 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright,
trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of Runco.
The trademarks reporduced in this Runco Owner’s Manual and used on the Runco Products are either owned by Runco or are
licensed by Runco. You may not reproduce or use the trademarks without the prior written consent of Runco.
Runco Products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents
Pending.
vi
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Thank you for your purchase of this quality Runco video product! For best performance, please read this manual carefully as it
is your guide through the menus and operation.
WARNING
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.
11. Only use the attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. The +12V trigger only outputs 12Vdc signal for triggering. Do not connect to any other power input or output. This could
cause damage to this unit.
16. Keep the packing material in case the equipment should ever need to be shipped.
17. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to
removing the lamp assembly for replacement.
18. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond rated life could cause them to
explode in rare occasions.
Q-750d Series Installation/Operation Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Never look directly into the lens when the lamp is on.
Compliance Information
DECLARATION OF CONFORMITY:
Manufacturer’s Name: Runco International, LLC
Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992
hereby declares that the Products’ Model Numbers:
Q-750d, Q-750d/CineWide and Q-750d/CineWide with AutoScope
conform with the provisions of:
Council Directive 2004/108/EC on Electromagnetic Compatibility;
EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment”
1998;
EN 55024 “Limits and methods of measurements of immunity characteristics of information technology equipment” 1998;
Including:
• EN 61000-4-2 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 2:
Electrostatic discharge immunity test”
• EN 61000-4-3 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 3: Radiated,
Radio-Frequency, Electromagnetic Field Immunity Test”
• EN 61000-4-4 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 4: Electrical
fast transient/burst immunity test”
• EN 61000-4-5 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 5: Surge
immunity test"
• EN 61000-4-6 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 6: Conducted
disturbances induced by radio-frequency fields immunity test"
• EN 61000-4-8 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 8: Conducted
disturbances induced by power frequency magnetic fields immunity test"
• EN 61000-4-11 "Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 11: Voltage
dips, short interruptions and voltage variations immunity tests"
And:
• EN 61000-3-2 "Electromagnetic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment
input current up to and including 16 A per phase)" 2000;
• EN 61000-3-3 "Electromagnetic compatibility (EMC) Part 3, Section 3: Limitations of voltage changes, voltage
fluctuations and flicker in public low-voltage supply systems, for equipment with rated current up to and including 16 A
and not subject to conditional connection" 1995;
Council Directive 2006/95/EC and amended by M1 and C1 on Low Voltage Equipment Safety;
EN 60950 “Safety of information technology equipment, including electrical business equipment”
The Technical Construction file required by this Directive is maintained at the corporate headquarters of Runco International,
LLC, located at 1195 NW Compton Drive, Beaverton, OR 97006-1992.
Date of Declaration: November 2009
viii
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC PART 15:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA (ICES-003):
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PRODUCT DISPOSAL:
The Product contains small amounts of tin, lead and/or mercury. Disposal of these materials may be regulated due to
environmental considerations.
IMPORTANT RECYCLE INSTRUCTIONS
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be
hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws.
DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European
Union and other European countries with separate collection programs)
This symbol found on your product or on its packaging, indicates that this product should not be treated as
household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences to the environment and human health, which could
otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve
natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please
contact your local authorities or dealer and ask for the correct method of disposal.
Q-750d Series Installation/Operation Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
x
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Table of Contents
RuncoCare™ Standard Two Year Limited Warranty ...................................................iii
Compliance Information .............................................................................................. viii
1. Introduction ...............................................................................................................1
About This Manual .......................................................................................................1
If You Have Comments About This Manual.............................................................1
2. Controls and Functions ............................................................................................5
Q-750d Rear Panel ......................................................................................................6
DHD Controller Front Panel ..........................................................................................7
3. Installation ...............................................................................................................13
Notes on Batteries................................................................................................13
Notes on Remote Control Operation.....................................................................13
Quick Setup ...............................................................................................................14
Installation Type....................................................................................................15
Q-750d Series Installation/Operation Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Other Considerations............................................................................................21
Connections to the Q-750d and DHD Controller ........................................................29
RS-232 Controller Connection..............................................................................36
Adjusting the Picture Orientation ................................................................................40
Anamorphic Lens Installation and Adjustment.......................................................41
4. Operation .................................................................................................................47
Using the On-Screen Menus ......................................................................................47
Input Source.........................................................................................................49
Aspect Ratio.........................................................................................................49
Picture..................................................................................................................52
Memory Presets ..................................................................................................58
5. Maintenance and Troubleshooting ........................................................................71
xii
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
6. External Control ......................................................................................................73
RS-232 Connection and Port Configuration..........................................................73
Using Discrete IR Codes ............................................................................................78
7. Specifications ..........................................................................................................81
DHD Controller Specifications ....................................................................................83
Q-750d Series Installation/Operation Manual
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Notes:
xiv
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1List of Figures
2-4. DHD Controller Rear Panel...........................................................................................8
3-1. Estimating Throw Distance.........................................................................................16
3-2. Projector Placement...................................................................................................18
3-3. Vertical Lens Shift (EXAMPLE ONLY)..........................................................................18
3-5. Folded Optics.............................................................................................................20
3-9. Q-750d/CineWide with Anamorphic Lens Base Plate and Ceiling Mounting Rails -
3-11. RS-232 Connection from the DHD Controller to the Q-750d ....................................30
3-12. HDMI Source Connections.......................................................................................31
3-16. S-Video and Composite Video Source Connections.................................................35
4-3. Typical Gray Bar Pattern for Adjusting Contrast..........................................................53
4-6. Overscan Modes........................................................................................................57
Q-750d Series Installation/Operation Manual
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
7-1. Overall Dimensions – Q-750d.....................................................................................84
xvi
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
This Owner’s Manual describes how to install, set up and operate the Runco Q-750d
Series LED Home Theater Projector and DHD Controller.
1.1
About This Manual
Throughout this manual, the Runco Q-750d Series LED Home Theater Projector and DHD
Controller are referred to collectively as the “Q-750d.”
Runco has prepared this manual to help home theater installers and end users get the
most out of the Q-750d.
Target Audience
Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
other Runco product manuals on-line, at www.runco.com.
If You Have Comments
About This Manual...
Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:
Textual and Graphic
Conventions
• Remote and built-in keypad button identifiers are set in upper-case bold type; for
example, “Press EXIT to return to the previous menu.”
• Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Letterbox, type LETTERBOX <Enter>.”
• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc>
and <Tab>.
• <Enter> indicates that you may press either the RETURN or ENTER key on your
keyboard if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:
A carriage return must be used after each command or string.
Note
Q-750d Series Installation/Operation Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
Tip
NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.
Note
CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.
Caution
WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.
WARNING
DANGER!
DANGER appears when a given action can cause severe injury or
death.
Use the following table to locate the specific information you need in this manual.
1.2
Using This Manual
If you need...
... Turn to page:
Information about obtaining service
General information about the Q-750d Series LED
Home Theater Projector and DHD Controller
Installation instructions
First-time configuration instructions
Advanced configuration instructions
Troubleshooting tips
Product specifications
2
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Integrating Runco's award-winning controller/processor technology for flawless images
from any source, the Q-750d sets new standards in projection with Runco's
game-changing InfiniLight™ LED lampless technology, Personal Color Equalizer and
Runco SmartColor.
1.3
Description, Features
and Benefits
Runco's revolutionary QuantumColor™ projectors pair energy-saving LED technology
with proprietary Runco engineering to create unsurpassed performance and unrivaled
customization. The Runco QuantumColor Q-750d maximizes the benefits of Runco's new
InfiniLight™ lampless LED illumination technology to provide an infinite light source that
creates an energy-efficient projector with the widest color gamut ever available in home
theater projection.
The Q-750d comes with an external, all-digital signal processor/controller/scaler featuring
advanced Vivix III™ video processing, superb scaling (up to 1080p) and aspect ratio
control. The Q-750d is enhanced further by significant horizontal and vertical lens shift
capability for maximum installation flexibility.
But simply creating a projector platform with lampless technology and the largest color
gamut isn't enough. Harnessing its incredible color options, Runco introduces its
revolutionary new Personal Color Equalizer™, which allows color adjustment that includes
those exactly defined by the cinematographer and the color preferences of each individual
viewer for each source. Proprietary Runco Smart Color (RSC™) provides a hue
compensation curve and gamut mapping that allows for lifelike, accurate flesh tones while
increasing color saturation, without sacrificing the purity of other colors.
In addition to Runco's proprietary InfiniLight, Personal Color Equalizer and Runco Smart
Color, the Q-750d can also be paired with Runco’s award-winning CineWide™ and
CineWide with AutoScope™ technology. CineWide provides uncompromised widescreen
reproduction of movies originally filmed in the CinemaScope™ 2:35:1 format. It maintains
constant vertical height on the screen just as in a movie theater. When a viewer transitions
from 1.78:1 (16:9) program material to superwide 2.35:1, the image simply gets wider
while full screen height is maintained, eliminating useless black bars on the top and
bottom of the screen.
Runco CineWide is achieved through Runco's ingenious combination of software,
electronics and precision anamorphic optics. With Runco CineWide, the projection
system is able to use the full pixel array, thereby producing a 2.35:1 image with enhanced
resolution and increased brightness. No resolution or image area is lost to those black
bars that contain no picture information. CineWide with AutoScope provides a motorized,
remote-controlled anamorphic lens mechanism.
CineWide requires the use of a 2.35:1 or similar aspect ratio superwide
format screen.
Note
Discrete IR and RS-232 control make custom installation seamless, while discrete source
and aspect ratio selection accommodate any automation control system.
Q-750d Series Installation/Operation Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Features and Benefits
The Q-750d offers these key features and benefits:
➤
• Full-HD Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio)
• InfiniLight™ lampless LED illumination technology provides an infinite, energy-efficient
light source
• Two HDMI Inputs (on DHD Controller) with High-bandwidth Digital Content Protection
(HDCP)
• HDTV Compatible
• ConstantContrast™ provides automatic, real-time LED drive adjustment, maximizing
contrast ratio and dynamic range especially in dark scenes
Parts List
Your Q-750d is shipped with the following items. If any items are missing or damaged,
please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.
➤
• Q-750d Series LED Home Theater Projector and DHD Controller
• Remote Control Unit and two (2), AAA-size batteries
• AC Power Cords (North America, Europe, United Kingdom), 8.2 feet (2.5 meters)
• Serial Port Adapter, RJ-11 Female to DB-9 Male
• RJ-11 Telephone Cable, 50 feet (15.24 meters)
• 5.0-mm Hex wrench (for lens shift adjustment)
• Rack-mount hardware for the DHD Controller
• Q-750d Series Installation/Operation Manual (this document)
• Runco Q-750d Quick Setup Guide
Optional Accessories:
• CineWide™ technology (fixed, secondary anamorphic lens)
• CineWide™ with AutoScope™ system (secondary anamorphic lens and motorized
mount)
• Ceiling mount kit (part number 956-0074-00)
• Short-throw primary lens, 1.56:1-1.86:1
• HDMI-to-HDMI Cable, length specified at time of order:
• 16.4 feet (5.0 meters) (part number 903-1010-00)
• 24.6 feet (7.5 meters) (part number 903-1011-00)
• 32.8 feet (10.0 meters) (part number 903-1012-00)
• 49.2 feet (15.0 meters) (part number 903-1013-00)
• 65.6 feet (20.0 meters) (part number 903-1014-00)
4
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Controls and Functions
Figure 2-1 shows the key Q-750d components.
Top IR Sensor
2.1
Q-750d at a Glance
Intake Vent
(on side)
Runco Logo
Focus Ring
Projection Lens
Front Bezel
Retaining
Screw
Zoom Ring
Front IR Sensor
Exhaust Vent
Status LED
Figure 2-1. Q-750d Front/Bottom/Side/Top Views
• TOP IR SENSOR
Receives infrared signals from the remote control unit.
• INTAKE VENT
Internal fans draw cool air into the projector through this vent.
• RUNCO LOGO
The logo can be rotated to match the projector orientation: inverted (ceiling-mounted)
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and
rotate it 180 degrees.
• FOCUS RING
Rotate this to focus the projected image.
• PROJECTION LENS
Available in two versions: standard throw range (1.85:1 to 2.40:1) and short throw
range (1.56:1 to 1.86:1).
• FRONT BEZEL RETAINING SCREW
Loosen this screw to allow removal of the decorative front bezel, which provides
access to the lens shift controls (refer to Lens Shift on page 34).
• ZOOM RING
Rotate this to change the projected image size.
Q-750d Series Installation/Operation Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• FRONT IR SENSOR
Receives infrared signals from the remote control unit.
• EXHAUST VENT
Warm air exits the projector through this vent. Ensure that it is not blocked.
• STATUS LED
Indicates projector status as follows:
• Solid green = AC power present, ready to turn on.
• Flashing green = Projector is initializing; keypad functions not allowed.
• Off = Normal operation.
• Flashing red = Over temperature, user intervention (clear vents, turn on AC) may fix
problem
• Solid red = Error that requires servicing (fan failure, Power-on Self-Test (POST)
failure).
Figure 2-2 shows the Q-750d rear panel.
2.2
Q-750d Rear Panel
RS-232
R S - 2 3 2
AC
A C
DHD INPUT
D H D I N P U T
1
2
3
Figure 2-2. Q-750d Rear Panel
1. RS-232C INPUT (9-pin, female D-Sub)
2. DHD INPUT
An HDCP-compliant digital video input for connecting the HDMI output from the DHD
Controller.
3. POWER INPUT (100 to 240 VAC)
Connect the Q-750d to power here.
6
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-3 shows the controls and indicators on the DHD Controller front panel; the
paragraphs that follow describe them.
2.3
DHD Controller Front
Panel
11 10
9
3
standby
Q-750d
m
e
HDMI 1
p
n
u
16:9
1080i/60
1
2
3
4
5
6
7
8
Figure 2-3. DHD Controller Front Panel
1. RUNCO ICON
Lights blue to indicate that the controller is on or powering up.
2. IR SENSOR
Receives IR commands from the remote control.
3. VACUUM FLUORESCENT DISPLAY
Can be used instead of the On-Screen Display (OSD). Displays currently-selected
menu or – if no menu is selected – the connected display device model, current
source, input resolution and aspect ratio.
4. ON/STANDBY BUTTON
Press once to toggle from standby mode to on mode. Press it again to return to
standby mode. For a discrete on or off command, you can use the direct access
buttons on the remote control.
5. LEFT BUTTON
Used to direct-select inputs or move the menu cursor left in the OSD. When no menu
is present on-screen, the LEFT button toggles through the different sources, in this
order:
HDMI 2 - HDMI 1 - SCART - HD 2 - HD 1 - Component - S-Video 2 - S-Video 1 -
Composite Video
6. DOWN BUTTON
Use to direct-select aspect ratios or move the menu cursor down in the OSD. When
no menu is present on-screen, this button toggles through the different aspect ratios,
in this order:
16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema - Native
Virtual Cinema is available only on the Q-750d/CineWide or
Q-750d/CineWide with AutoScope. For more information about
Note
Q-750d Series Installation/Operation Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. RIGHT BUTTON
Used to direct-select inputs or move the menu cursor right in the OSD. When no
menus are present on-screen, the RIGHT button toggles through the different
sources, in this order:
Composite Video - S-Video 1 - S-Video 2 - Component - HD 1 - HD 2 - SCART -
HDMI 1 - HDMI 2
8. MENU BUTTON
Press the MENU button to bring up the main menu, or to exit the current menu and
return to the previous one.
9. UP BUTTON
Use to direct-select aspect ratios or move the menu cursor up in the OSD. When no
menus are present on-screen, the UP button toggles through aspect ratios in the
following order:
Native - Virtual Cinema - Cinema - VirtualWide - Letterbox - 4:3 - 16:9
10. ENTER BUTTON
When an item is highlighted on the OSD, the ENTER button selects the item.
11. STANDBY LED
Lights amber when the DHD Controller is in standby mode; otherwise it is off.
Figure 2-4 shows the rear connector panel on the DHD Controller.
2.4
DHD Controller Rear
Panel
13
12
3
11
2
10
5
6
7
8
9
14
1
4
Figure 2-4. DHD Controller Rear Panel
8
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. HDMI Out
Outputs
2. Display Control
Connect this to the RS-232 input on the Q-750d, using the provided communication
cable.
3. TRIGGERS
Connection for up to three (3), 12-volt trigger-controlled devices such as retractable
screens, screen masks or a CineWide with AutoScope system. Output current is
limited to 250 milliamperes (mA).
4. USB
Inputs
A standard, USB Series “B” connection to a personal computer. (For future use.)
5. HDMI 1 / HDMI 2 (Digital)
HDCP-compliant digital video inputs for connecting an HDMI or DVI source.
6. HD1 / HD2 (5 x Analog BNCs)
Two inputs (five BNCs per input) for connecting standard-definition (SD = 480i/576i),
enhanced-definition (ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p)
component video sources, or RGBHV sources such as personal computers.
7. Component / SCART (5 x RCA connectors)
SD/HD input for connecting SDTV, EDTV or HDTV component video sources, or
RGBHV sources. Also provides RGB input for SCART RGBS sources.
8. Video
Standard, composite video input for connecting a VCR, camcorder or other
composite video source. Also provides composite sync input for SCART RGBS
sources.
9. S-Video 1 / S-Video 2
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super
VHS (S-VHS) VCR.
10. IR
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system. It is a
3.5-mm, mini phono jack, wired as follows:
Ring = No connection
Tip = IR Input
Sleeve = Ground
11. RS-232 / RS-485
A female, 9-pin D-sub connector for interfacing with a PC or automation/control
system. (Currently, only RS-232 interface is supported.)
12. MAIN AC FUSE
This is the main AC input fuse (5mm x 20mm, 500 mA, 250V slow-blow).
13. MAIN POWER SWITCH
Disconnects or applies power to the DHD Controller.
14. POWER INPUT (100 to 240 VAC)
Connect the DHD Controller to power here.
Q-750d Series Installation/Operation Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-5 shows the Q-750d remote control, and the paragraphs that follow describe its
functionality.
2.5
Q-750d Remote
Control Unit
2
1
3
4
(not available on
some models)
RETURN
5
7
EXIT
6
8
9
16 : 9
4 : 3
11
12
13
10
HDMI
1
HDMI
2
14
CUST
1
CUST
2
SVC
Figure 2-5. DHD Controller/Q-750d Remote Control
10
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. IR OUTPUT INDICATOR
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2. ON / OFF
Press to turn the projector on or off.
3. ENTER
Press to select a highlighted menu item or confirm a changed setting.
4. Cursor Buttons ( ,
,
,
)
Use these buttons to select items or settings, adjust settings or switch display
patterns.
When no menu is present on-screen, the UP and DOWN buttons toggle through the
available aspect ratios, in this order:
UP Button = Native - Virtual Cinema - Cinema - VirtualWide - Letterbox - 4:3 - 16:9
DOWN Button = 16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema -
Native
Virtual Cinema is available only on the Q-750d/CineWide. For more
information about aspect ratios, refer to Table 4-1.
Note
Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in
this order:
LEFT Button = HDMI 2 - HDMI 1 - SCART - HD 2 - HD 1 - Component - S-Video 2 -
S-Video 1 - Composite Video
RIGHT Button = Composite Video - S-Video 1 - S-Video 2 - Component - HD 1 -
HD 2 - SCART - HDMI 1 - HDMI 2
5. RETURN / EXIT
Press this button to exit the current menu and return to the previous one.
Not all remote control units have this button. If yours does not, use
the MENU button (see below) to exit the current menu.
Note
6. LIGHT
Press to illuminate the buttons.
7. MENU
Press this button to access the OSD controls, or to exit the current menu and return
to the previous one.
8. VIDEO (1)
Press to select Composite video input as the source or to enter the numeric
character “1.”
9. COMP (Component) (2)
Press to select Component/SCART video input as the source or to enter the numeric
character “2.”
Q-750d Series Installation/Operation Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Aspect Ratio Selection Buttons
Use the red buttons to select an aspect ratio directly or to enter numeric characters,
as follows:
16:9 (3)
For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.
4:3 (6)
Scales the input signal to fit 4:3 display mode in the center of the screen.
LETBOX (Letterbox) (9)
For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.
V-WIDE (VirtualWide)
Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.
CINEMA
For viewing 2.35:1 source material.
SVC (CineWide-equipped projectors only)
Selects the Virtual Cinema aspect ratio, used for viewing 16:9 source material on a
2.35:1 screen.
11. S-VID 1 (4) / S-VID 2 (5) (S-Video)
Press to select an S-Video input or to enter the numeric character “4” or “5.”
12. HD 1 (7) / HD 2 (8)
Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric
character “7” or “8.”
13. HDMI 1 / HDMI 2 (0)
Press to select a Digital Video input. Press HDMI 2 to enter the numeric character
“0.”
14. Memory Preset Buttons:
ISF NIGHT
Press to recall settings for the current input from the “ISF Night” memory preset.
ISF DAY
Press to recall settings for the current input from the “ISF Day” memory preset.
CUST 1
Press to recall settings for the current input from the “Custom 1” memory preset.
CUST 2
Press to recall settings for the current input from the “Custom 2” memory preset.
12
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installation
Installation must be performed by a qualified custom video
installation specialist.
Note
To install batteries in the remote control,
press up on the battery cover retainer clip
and lift off the cover. Install the two AAA
batteries with the correct polarity and then
replace the cover.
3.1
Remote Control
• Make sure that the battery polarities are correct when installing the batteries.
• Do not mix an old battery with a new one or different types of batteries.
Notes on Batteries
• If you will not use the remote control for a long time, remove the batteries to avoid
damage from battery leakage.
• Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the projector.
Notes on Remote Control
Operation
• If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the projector, and repeat the operation.
Q-750d Series Installation/Operation Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1 gives a quick overview of the Q-750d installation process. The sections
following this one provide detailed instructions.
3.2
Quick Setup
Table 3-1. Installation Overview
For Details, Refer to
page...
Step
Procedure
Choose a location for the projector
1
2
Install CineWide lens mounting assembly (stationary base
plate or AutoScope lens motor – optional)
Mount the projector
3
4
5
6
Connect the DHD Controller to the projector
Connect signal sources to the DHD Controller
Connect external controller to RS-232 port (optional)
Connect 12-volt trigger outputs to AutoScope lens motor
and/or other equipment (optional)
7
8
9
Connect projector, DHD Controller and lens motor (if
present) to AC power and power up
Primary lens adjustments: projected image size (zoom),
position (shift) and focus
For rear-screen and/or ceiling-mount installations, select
the proper picture orientation
10
11
12
Install CineWide anamorphic lens (optional)
CineWide lens adjustments: position, pitch (angle),
geometry and focus
Display calibration: adjust the following for each input and
display mode (resolution and frame rate); save settings
when finished:
• Aspect ratio
• Brightness
• Contrast
13
• Color level
• Tint
• Sharpness
• White Balance
14
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation of your projector will ensure the quality of your display. Whether you are
installing a projector temporarily or permanently, you should take the following into
account to ensure your projector performs optimally.
3.3
Installation
Considerations
Choose the installation type that best suits your needs: front or rear screen, floor mount or
Installation Type
Table 3-2. Projector Installation Options
Advantages
Front Screen, Floor Mount Installation
• Shares floor space with audience
Considerations
• Easy to set up
• Can be moved or changed quickly
• Easy to access
Front Screen, Inverted Mount (ceiling) Installation
• Does not take up audience space
• Projector is unobtrusive
• Installation is more permanent
• Projector access is more difficult
• Projector cannot be accidentally moved
Rear Screen, Floor Mount Installation
• Projector is completely hidden
• Projector is easily accessed
• Requires separate room
• Installation cost is usually higher
• Usually good ambient light rejection
Rear Screen, Inverted Mount (ceiling) Installation
• Projector is completely hidden
• Requires separate room
• Usually good ambient light rejection
• Installation cost is usually higher
Rear Screen, Floor Mount with Mirror
• Projector is completely hidden
• Usually good ambient light rejection
• Requires less space behind screen than
other rear screen installations
• Requires separate room
• Installation cost is usually higher
Q-750d Series Installation/Operation Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ambient Light
In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your
images will be noticeably reduced if light directly strikes the screen, such as when a shaft
of light from a window or floodlight falls on the image. Images may then appear washed
out and less vibrant.
➤
➤
Throw Distance
Throw distance is the distance measured from the front of the projector to the screen.
This is an important calculation in any projector installation as it determines whether or not
you have enough room to install your projector with a desired screen size and if your
image will be the right size for your screen.
You can quickly estimate the throw distance by taking the width of the screen and
roughly how far back the projector should be positioned from the screen in order to
project a focused image large enough to fill the screen.
Estimating Throw Distance
Throw Distance (TD) = Screen Width (w) x Lens Throw Ratio
Scr
een w
idth (w)
TD
Figure 3-1. Estimating Throw Distance
16
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-3 lists the available lens options for the Q-750d and their associated throw ratios.
Table 3-3. Throw Ratios for the Q-750d Series
Throw Range in
inches, with
72.6x40.8-inch
(1.78:1) Screen
ThrowRatio
with
Primary
Lens and
Anamorphic
Lens
Throw Range in
inches, with
96x40.8-inch (2.35:1)
Screen
Throw
Ratio with
Primary
Projector Model
Lens Only
Minimum Maximum
Minimum Maximum
Standard Q-750d
1.85 – 2.40
1.56 – 1.86
134.31
113.26
174.24
135.03
(n/a)
Standard Q-750d
with Optik A
(n/a)
Primary Lens
Q-750d/CineWide
(Rainier II
Anamorphic Lens)
(n/a)
134.31
(n/a)
1.52 – 1.80
1.52 – 1.80
1.39 – 1.80
1.17 – 1.40
145.92
145.92
133.44
112.32
172.80
172.80
172.80
134.40
Q-750d/CineWide
with AutoScope
(Rainier II
1.85 – 2.40
174.24
Anamorphic Lens)
Q-750d/CineWide
(McKinley
Anamorphic Lens)
Q-750d/CineWide
(Optik A Primary
Lens and McKinley
Anamorphic Lens)
(n/a)
Q-750d/CineWide
with AutoScope
(McKinley
1.85 – 2.40
1.56 – 1.86
134.31
113.26
174.24
135.03
1.39 – 1.80
1.17 – 1.40
133.44
112.32
172.80
134.40
Anamorphic Lens)
Q-750d/CineWide
with AutoScope
(Optik A Primary
Lens and McKinley
Anamorphic Lens)
Q-750d Series Installation/Operation Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical and Horizontal
Proper placement of the projector relative to the screen will yield a rectangular,
perfectly-centered image that completely fills the screen.
➤
Position
Ideally, the projector should be positioned perpendicular to the screen and in such a way
that the lens center is aligned with either the top or bottom edge of the screen area, and
centered horizontally. See Figure 3-2.
Ceiling Installation
Ceiling
Height
Projection Distance
x
Lens Center
Lens Center
Screen
Floor Installation
Screen
Lens Center
Height
Lens Center
x
Projection Distance
Floor
Figure 3-2. Projector Placement
Vertical and Horizontal
Lens Shift
You can use the lens shift controls to center the image on the screen. Lens shift is
generally expressed as a percentage of the screen height or width, as shown in Figure 3-3
➤
Screen Center
0%
50% Height
Lens Shift
(0.5 x H)
Base plate
to lens center =
approx. 5-6" (depending
on the amount of lens shift)
100% Height
Lens Shift
(1.0 x H)
Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular
lens or projector is used in this example.
Figure 3-3. Vertical Lens Shift (EXAMPLE ONLY)
18
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
100% Width Lens Shift
(1.0 x W)
50% Width Lens Shift
(0.5 x W)
Screen Center
0%
Screen Width (W)
Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular
lens or projector is used in this example.
Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY)
Vertical Lens Shift (Standard Q-750d): The Q-750d provides up to 60% of vertical
lens shift up or down. For example, with a 100 x 56 inch (1.78:1) screen, you can shift
the image up to 33.60 inches (0.85 meters) above or below the screen center.
Vertical Lens Shift (Q-750d/CineWide or Q-750d/CineWide with AutoScope): The
Q-750d provides up to 25% of upward vertical lens shift and up to 60% of
downward vertical lens shift. For example, with a 100 x 56 inch (1.78:1) screen, you
can shift the image up to 14.00 inches (0.36 meters) above or 33.60 inches (0.85 meters)
below the screen center.
Vertical lens shift figures are for ceiling mount
configurations. For floor installations (where the projector is
Note
upright), reverse the up/down vertical lens shift percentages.
Horizontal Lens Shift: The Q-750d provides up to 12.5% of horizontal lens shift
left or right. For example, with a 100 x 56 inch (1.78:1) screen, you can shift the image
up to 12.50 inches (0.32 meters) left or right of the screen center.
Q-750d Series Installation/Operation Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Folded Optics
In rear screen applications where space behind the projector is limited, a mirror may be
mirror must be accurately set. If you are considering this type of installation, contact your
dealer for assistance.
➤
Screen
Mirror
Figure 3-5. Folded Optics
Audio/Video
Synchronization Issues
Due to its extraordinarily high level of video processing performance, the DHD Controller
may distribute video signals with a perceptible level of audio latency. In order to easily
solve this issue, Runco recommends using the DHD Controller with a high-quality audio
receiver that has the ability to effectively synchronize audio and video signals.
➤
Most mainstream audio receiver/switchers have the ability to synchronize the audio and
video to the Advanced Television Systems Committee (ATSC) prescribed tolerances.
According to the ATSC, the sound program should never lead the video program by more
than 15 milliseconds, and should never lag behind the video program by more than 45
milliseconds.
In addition, many video displays and A/V receivers introduce additional latency that needs
audio latency given different signal input timings.
Table 3-4. Possible Audio Latency for Various Input Timings
Input Timing
480i
Possible Audio Latency (milliseconds)
133
83
480p
576i
160
100
100
83
576p
720p/50
720p/60
1080i/25
1080i/30
1080p/24
1080p/50
1080p/60
160
133
125
80
67
20
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Other considerations and tips that can help improve your installation:
Other Considerations
• Keep the ambient temperature constant and below 35°C (95°F). Keep the projector
away from heating and/or air conditioning vents. Changes in temperature may cause
drifts in the projector circuitry, which may affect performance.
• Keep the projector away from devices that radiate electromagnetic energy such as
motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers and elevators.
If you are installing a standard (non-CineWide) Q-750d, skip this step and proceed with
3.4
Installing the Optional
CineWide/AutoScope
Lens Mount
If you are installing a Q-750d/CineWide, proceed with Installing the Fixed CineWide
If you are installing a Q-750d/CineWide with AutoScope, proceed as follows to install the
AutoScope lens motor.
1. Do not install the CineWide lens yet, only the fixed CineWide
Note
base plate or AutoScope lens motor. You will install the
CineWide lens after you install the projector and adjust the
primary lens.
2. Some components shipped with your projector may differ slightly
from what is shown in these instructions.
Q-750d Series Installation/Operation Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the AutoScope
Lens Motor
Figure 3-6 shows the Q-750d/CineWide with AutoScope motor assembly.
➤
(Q-750d/CineWide with
AutoScope)
CineWide with AutoScope
Ceiling Mt. Adapter/
3
Projector Stand, Right
Screw, Phillips
Pan-Head,
2
M6-1.0 x 12mm (14x)
4
CineWide with
AutoScope
Ceiling Mt. Adapter/
Projector Stand, Left
1
AutoScope
Lens
Motor
Figure 3-6. Q-750d/CineWide with AutoScope Motor Assembly – Exploded View
22
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove Projector Front Feet:
Remove
Place the projector upside down on a
blanket or other soft surface. Loosen
and remove the two front feet on the
projector.
Install Ceiling Mount Adapters/Projector Stands: For ceiling installations, these
brackets bring the mounting points for the projector mounting plate (included with the
projector ceiling mount kit) from the bottom of the projector up and around the AutoScope
lens motor housing. For floor installations (where the projector is upright), the adapters
allow the projector to lie flat on the mounting surface.
Using six (6) each of the supplied, M6 x 12mm Pan-Head Phillips screws (item #2), attach
the AutoScope Ceiling Mount Adapters/Projector Stands (items #3 and #4) to the
projector as shown in Figure 3-7.
Q-750d Series Installation/Operation Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3-7. Q-750d with Ceiling Mount Adapters/Projector Stands
DO NOT OVER-TIGHTEN THE SCREWS.
Caution
Install Lens Motor:
2. Line up the mounting holes on the lens motor housing with those on the underside of
the projector.
24
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Secure the motor to the projector with the eight (8) remaining M6 x 12mm Pan-Head
Phillips screws.
Figure 3-8. AutoScope Lens Motor Installation
After you have installed the AutoScope lens motor, proceed with Mounting the Q-750d
(page 28).
Q-750d Series Installation/Operation Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Fixed
Figure 3-9 shows the anamorphic lens base plate assembly for a Q-750d/CineWide.
➤
CineWide Base Plate
(Q-750d/CineWide)
Ceiling Mount
Rails (part of
Ceiling Mount
Kit)
1
Screw,
Phillips
Pan-Head,
M6 x 1.0 x
12mm (6x)
2
Anamorphic
Lens Base Plate
Figure 3-9. Q-750d/CineWide with Anamorphic Lens Base Plate and Ceiling
Mounting Rails - Exploded View
26
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
To install the fixed CineWide base plate on a Q-750d/CineWide:
1. Place the projector upside down on a blanket or other soft surface.
2. Place the CineWide base plate on the bottom of the projector.
3. If you are mounting the projector on a ceiling: Line up the three holes on the left
and right mounting rails (included with the projector ceiling mount kit) with those on
the projector and base plate.
4. Secure the CineWide base plate (and ceiling mounting rails, if needed) to the projector
with the Pan-Head Phillips screws provided with the CineWide lens base plate.
1. Do not use the mounting screws provided with the ceiling
mounting kit. Use only the hardware provided with the CineWide
Caution
lens base plate.
2. DO NOT OVER-TIGHTEN THE SCREWS.
Q-750d Series Installation/Operation Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
There are several methods for mounting the projector. Depending on your chosen
installation, one method may be more suitable than another.
3.5
Mounting the Q-750d
Floor Mounting (Upright)
In typical front and rear screen installations, the projector can be mounted to a secure and
level surface such as a table or cart. Carts are useful when moving a projector during a
presentation or from site to site. If possible, lock the wheels when it’s in position to prevent
it from being moved during a presentation.
➤
Ceiling Mounting
(Inverted)
For fixed installations, and for those that want the projector out of sight or have a limited
space for projector and audience, you can invert the Q-750d and suspend it from the
ceiling using a specially-designed ceiling mount fixture.
➤
Use only the Runco-approved ceiling mount kit designed for your
projector. Install the mount kit according to the instructions
provided with it.
Note
The projector can also be inverted and placed in an enclosure above and behind the
viewing area. Install four feet on the inside bottom surface of the enclosure on which the
projector can rest. A variety of materials can be used for this purpose (for example, rubber
crutch tips or turntable feet).
Adjusting the Projection
Angle
If the Q-750d is ceiling-mounted and the screen is significantly lower than the projector,
you can tilt the projector at a slight angle by adjusting the ceiling mount.
➤
If you do this, you may need to shift the image using the on-screen display (OSD) controls,
28
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proceed as follows to connect the DHD Controller to the Q-750d, your video sources,
external controller(s) – if present – and AC power.
3.6
Connections to the
Q-750d and DHD
Controller
When connecting your equipment:
• Turn off all equipment before making any connections.
• Use the correct signal cables for each source.
• Ensure that the cables are securely connected. Tighten the thumbscrews on
connectors that have them.
To access the connector panel, pull
firmly on the cable access cover to
open it.
Connector Panel Access
Digital Video Connection: Connect the HDMI Output of the DHD Controller to the DHD
Connecting the DHD
Controller to the Q-750d
RS-232
R S - 2 3 2
AC
A C
DHD INPUT
D H D I N P U T
HDMI
OUT
RS-232
OUT
Figure 3-10. Connecting the Q-750d to the DHD Controller
Q-750d Series Installation/Operation Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Connection: Connect the Display Control output from the DHD Controller to
the RS-232 input on the Q-750d. Use a standard, modular telephone cable with RJ11
plugs at both ends. On the Q-750d end, use the provided RJ11-to-DB9 adapter. This
RS-232
XMT DATA
RCV DATA
RCV DATA
XMT DATA
R S - 2 3 2
3
2
5
4
3
To/From
DHD
Controller
SIG GND
2
1, 4, 6,
7, 8, 9
1, 5, 6
NO CONNECTION
6-position
RJ-11 Male
DB-9 Male
6
1
6
1
Figure 3-11. RS-232 Connection from the DHD Controller to the Q-750d
30
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect your video sources to the DHD Controller as shown and described in the
sections that follow.
Connecting Source
Components to the DHD
Controller
Use the HDMI inputs whenever possible. This ensures the highest
Tip
video quality because the signal is carried in the digital domain
throughout the entire signal path, from source component output
into the projector.
You can also connect computers with DVI output to these inputs.
input signals.
Note
HDMI
AV OUT
HDMI
AV OUT
HDMI sources (BD, DVD, DTV Set-Top Box etc.)
Figure 3-12. HDMI Source Connections
Q-750d Series Installation/Operation Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Component Video Source Connections: Connect your component video sources to
RCA-to-BNC
adapter
COMPONENT
VIDEO OUT
Y
PB
PR
DTV-Set-Top Box
(DTV-STB)
BD/DVD
Figure 3-13. Component Video Source Connections
32 Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SCART RGBS Source Connections: Connect the green, blue and red outputs from
your SCART source to the Component/SCART input on the DHD Controller. Connect the
sync output from your SCART source to the Video input on the DHD Controller. See
VCR
SCART-to-RGBS
adapter
Green
DVD/DTV STB
Blue
Red
Sync
Gaming Console
Figure 3-15. SCART RGBS Source Connections
34
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Controller
Connection
Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation
system (if present) to the RS-232 port on the DHD Controller; see Figure 3-17.
➤
5
4
3
1
2
6
9
8
7
2 Receive Data
3 Transmit Data
5 Ground
to Automation/
Control System
or PC
(none of the other pins are used)
Figure 3-17. RS-232 Control System Connection
36
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
If your Q-750d is equipped with a CineWide with AutoScope system, connect the
Connecting 12-volt
Trigger Outputs to
External Equipment
Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or
screen masks) to the other trigger outputs.
AutoScope Lens Motor
Power
Switch
AC Input
3.5-mm
mini plug
Retractable Screen or other
12-volt trigger-activated
device
Sleeve = Ground
Tip = +12V
Figure 3-18. Connecting 12-volt Trigger Outputs
Q-750d Series Installation/Operation Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an External IR
Receiver to the DHD
Controller
If infrared signals from the remote control cannot reach the DHD Controller due to
excessive distance or obstructions such as walls or cabinet doors, you can connect an
external IR receiver to the DHD Controller to extend the range of the remote control. See
➤
Remote Control
IR Sensor
IR Repeater
(3.5-mm, mini
phono plug)
Figure 3-19. External IR Receiver Connection
38
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector/DHD Controller: Plug the female end of one power cord into the AC
receptacle on the rear of the Q-750d (AC 100V ~ 240V). Then, connect the other end to
your AC power source.
Connecting to AC Power
Similarly connect the DHD Controller to a nearby AC outlet.
AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power
cord is provided for the lens motor. Plug the female end of the AC power cord into the AC
input on the rear of the lens motor assembly. Connect the other end to your AC power
source.
1. Turn on your source components.
3.7
Turning on the Power
2. Turn on the main power switch at the rear of the DHD Controller.
3. If this is an AutoScope-equipped projector, turn on the main power switch at the rear
of the AutoScope lens motor. The lens motor power switch is located next to the AC
input.
4. Press the ON button on the remote control (or the ON/STANDBY ( ) button on
DHD Controller front panel) to turn on the system. The vacuum fluorescent display on
the DHD Controller front panel briefly displays “Initializing System,” followed by
“Starting Q-750d.” On the projector, the LED flashes green to indicate that it is
warming up.
5. When the projector is ready for use, the LED turns off. On the DHD Controller, the
fluorescent display indicates the active source, input resolution/frame rate and aspect
ratio; for example:
Current
Source
Q-750d
16:9
HDMI 1
1080i/60
Aspect Ratio
Input Resolution/Frame Rate
Q-750d Series Installation/Operation Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
The Q-750d gives you a great deal of control over the picture size, position and focus.
3.8
Primary Lens
Adjustments
Focus and Zoom
To focus the projected image, grasp the lens by
the outer ring and rotate it.
➤
Zoom
out
Zoom
in
To make the picture smaller (zoom out) or larger
(zoom in), move the zoom tab in the appropriate
direction.
Focus
Lens Shift
To access the lens shift controls, loosen the Phillips screw at the bottom of the decorative
bezel on the front of the projector (see w). Then, remove the bezel.
➤
Vertical Lens Shift: To shift the
projected image vertically, insert the
provided hex wrench into the vertical
lens shift adjuster at the top of the
projector (directly above the lens).
Then, turn the wrench as shown to
shift the lens in the desired direction.
Horizontal
Lens Shift
Vertical
Lens Shift
Horizontal Lens Shift: To shift the
projected image horizontally, insert
the provided hex wrench into the
horizontal lens shift adjuster at the
top of the projector. Then, turn the
wrench as shown to shift the lens in
the desired direction.
Lens
When you have finished adjusting the lens position, re-install the front bezel.
By default, the Q-750d is configured for a “floor/front” installation, in which the projector is
installed upright and in front of the screen. If it is installed behind the screen and/or
mounted on a ceiling, you must change the picture orientation. To do this:
3.9
Adjusting the Picture
Orientation
1. On the DHD Controller remote control or front panel, press MENU.
2. Select Service from the Main Menu and enter the Service Menu passcode.
You must enter a passcode to access the Service menu.
Note
3. Select Display Device from the Service Menu.
4. Select Configure from the Display Device menu, then select Installation.
40
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select Orientation, then choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match
the installation method. Or, for front-projection installations, use the Auto setting to
have the projector automatically determine the orientation (floor or ceiling) using an
internal sensor.
If you are installing a Q-750d/CineWide or Q-750d/CineWide with AutoScope, proceed as
follows to install and adjust the anamorphic lens.
3.10
Installing and
Adjusting the
CineWide Anamorphic
Lens
It is extremely important that the primary lens is properly
Note
adjusted before you install the anamorphic lens. Ensure that
the image from the primary lens is perfectly centered on the
screen.
Some components shipped with your projector may differ slightly from what is shown in
these instructions. If any items are missing or damaged, please contact your Runco dealer
or Runco Customer Service at (800) 23-RUNCO.
Anamorphic Lens
Installation and
Adjustment
Lens Adapter Ring and
1
Mounting Screws (3x)
Anamorphic Lens
10
Set Screw
Pitch Adjustment
T-Nut (2x)
9
Pitch Adjustment Yoke for Lens
2
Height/Y Adjustment
T-Screw and Washer
(2x)
3
4
Pitch Adjustment
T-Screw and
Washer (2x)
Anamorphic Lens
Holder
5
Yaw/X Adjustment
Lever (2x)
8
1/4-20 Hex Bolt (2x)
and Washer (2x)
6
7
AutoScope Carriage Plate or
Fixed CineWide Base Plate
Figure 3-20. Anamorphic Lens Mounting Assembly - Exploded View
Q-750d Series Installation/Operation Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Lens Mounting Assembly to Lens Motor Carriage Plate or Fixed CineWide
Base Plate:
1. Remove the two Yaw/X Adjustment Levers (item #8) from the bottom of the
Anamorphic Lens Holder (item #5).
2. Place the Anamorphic Lens Holder on top of the AutoScope Carriage Plate or Fixed
CineWide Base Plate (item #7). Position the bracket so that the long slot at the bottom
of the lens holder is perpendicular to the corresponding slots on the plate.
3. Secure the Anamorphic Lens Holder to the plate using the Hex Bolts/Washers
(item #6) and Yaw/X Adjustment Levers that you removed in Step 1.
4. Use the Lens Mounting Screws to attach the Lens Adapter Ring (item #1) to the Pitch
yoke.)
5. Use the Height/Y Adjustment T-Screws/Washers (item #3), Pitch Adjustment
T-Screws/Washers (item #4) and T-Nuts (item #9) to attach the Pitch Adjustment
Yoke and Lens Adapter Ring to the Anamorphic Lens Holder. The Yoke should be
as close to the primary lens as possible.
6. Attach the lens to the Lens Adapter Ring by threading it clockwise.
Lens threads into ring
Figure 3-21. Attaching the Anamorphic Lens to the Lens Ring
42
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Lens Motor Trigger (Q-750d/CineWide with AutoScope only): CineWide
with AutoScope maintains constant image height independent of the aspect ratio, while
using the full display resolution of the projector. It accomplishes this by moving the
anamorphic lens in front of the primary lens when widescreen material is being viewed.
When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens
moves out of the light path.
To configure the lens motor trigger on the DHD Controller for proper AutoScope
operation:
1. Project a 2.35:1 aspect ratio test pattern or other image on the screen.
2. On the DHD Controller remote control or front panel, press MENU.
3. Select Service from the Main Menu and enter the Service Menu passcode.
You must enter a passcode to access the Service menu for the first
time after turning on the system.
Note
4. Select Triggers from the Service menu.
5. Assign the trigger output to which the lens motor is connected to the Cinema and
Virtual Cinema aspect ratios. This enables the lens motor to move the anamorphic
lens into position (in front of the primary lens) when either aspect ratio is selected.
6. Select the Cinema aspect ratio to move the anamorphic lens into position, if it isn’t
or press
or
repeatedly with no menus visible on-screen.
Adjusting the Horizontal (X) Lens Position:
1. Project a white field on the screen.
2. Loosen the Yaw/X-Adjustment Levers underneath the lens.
3. Slowly move the anamorphic lens into place (from right to left or vice versa) so that
there are no shadows on either side of the screen:
Too Far Left
Correct position
Too Far Right
4. When the horizontal position is properly set, tighten the Yaw/X-Adjustment Levers to
secure the lens in place.
Q-750d Series Installation/Operation Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Height (Y): With the white field still on-screen, loosen the
Height/Y Adjustment T-Screws on either side of the lens. Then, slowly move the
anamorphic lens into place so that there are no shadows on the top or bottom of the
screen:
Too Low
Correct position
Too High
When the height is properly set, tighten the Height Adjustment T-Screws to secure the
lens in place.
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom
pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below
the Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely.
Then, adjust the anamorphic lens angle so that the projected image is rectangular:
Correct Lens Angle
Incorrect Lens Angle
The anamorphic lens will almost always be angled with respect to the projector; this is
normal.
Once the proper lens angle has been set, firmly tighten the Pitch Adjustment T-Screws to
secure the lens in place.
There may be some pincushion distortion even after the lens is
Note
properly adjusted, especially at shorter throw distances. If this is the
case, Runco recommends that you slightly over-scan the image
into the screen frame area to mask the distortion.
44
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Yaw: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely
from side to side. Then, angle the lens to even out any left-right pincushion distortion:
Anamorphic Lens (Top View)
Correct Position
Wrong Position
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to
secure the lens in place.
Q-750d Series Installation/Operation Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Geometry:
1. Input an anamorphic cross-hatch test pattern to the projector.
2. Unscrew the Anamorphic Lens just enough to allow it to rotate freely.
3. Grasp the lens by the center ring and rotate the lens until the image is properly
anamorphic:
Wrong Position
Correct Position
4. When the image geometry appears correct, tighten the
Anamorphic Lens Set Screw (item #10) to secure the lens in place.
(When viewed from the front, the rear opening on the anamorphic
lens should appear as a tall, narrow oval.)
Focus: Finally, rotate the Focus Ring on the anamorphic
lens to fine-tune the optical focus.
46
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation
DHD Controller front panel (Figure 2-3).
4.1
Using the On-Screen
Menus
To select a menu item, use the and buttons on the remote control or DHD Controller
front panel to highlight it. Then, to confirm your selection, press ENTER on the remote
control or DHD Controller front panel.
Depending on the selected input source and signal characteristics, some menu options
may not be available.
Composite
S-Video 1
S-Video 2
Component
HD1
Gain
-100, -99... 0 ... 99, 100
(Red, Green, Blue)
Offset
Gamma
1.8, 2.0, 2.2, 2.35 or 2.5
Simple
(5500K, 6500K, 7500K or
9300K)
Color Temp
SatCo
Input Source
HD2
On or Off
SCART
ConstantContrast
Low, Medium, High or Off
HDMI 1
HDMI 2
16:9
Auto, REC709, SMPTE-C,
EBU, Native, DCI or PCE
Color Gamut
Display Color
Hue (Red / Yellow / Green /
Cyan / Blue / Magenta)
4:3
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
Saturation (Red / Yellow /
Green / Cyan / Blue /
Magenta)
Aspect Ratio
Picture
PCE
Level (Red / Yellow / Green
/ Cyan / Blue / Magenta)
Runco Smart Color (RSC)
(On or Off)
Brightness
Contrast
Color
White Balance (Red / Green
/ Blue Gain)
Tint
Brightness
Contrast
Color
Sharpness
Noise Filter
Left/Right
Up/Down
Width
Input Image
Input Color
-50, -49 ... 0 ... 49, 50
Calibration
Tint
Sharpness
Gain
-32, -31... 0 ... 31, 32
(HD 1, HD 2 and
Component inputs only)
Height
Offset
Overscan
0, 1, 2 ... 7
(S-Video 1, S-Video 2 and
Composite inputs only)
Overscan Mode
(Zoom/Crop)
Input Position
Chroma Delay
Phase
Noise Filter
0, 1, 2 ... 63
(RGB/Component/SCART signals
only)
Save ISF Night
Save ISF Day
Back / Confirm
Tracking
(RGB/Component/SCART signals
only)
Copy Settings
Paste Settings
Left/Right
Copy/Paste
Recall ISF Night
-50, -49 ... 0 ... 49, 50
Recall ISF Day
Up/Down
Memory
Presets
Output Shift
Recall/Save Custom 1
Recall/Save Custom 2
Width
-50, -49, 48 ... 0
Height
Reset Custom 1 and Custom 2 to
Factory Default
Owner Name
ISF Calibrated
ISF Other
Off, 30 Minutes, 60 Minutes, 90
Minutes, 2 Hours or 4 Hours
Sleep Timer
Information
Splash Configure
OSD Position
Splash Timer
Splash Enable
Hor. / Ver.
5, 6, 7 ... 15 ... 59, 60
On/Off
Signal
System
0, 1, 2 ... 100
Field Service
Manufacturing
Note: Default settings appear in bold type.
Figure 4-1. DHD Controller OSD Menu Structure for Q-750d
Q-750d Series Installation/Operation Manual 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Bars 1
Color Bars 2
Focus
Test Video
Grey Bars
Input Names
Rename/Restore
Remote Code
COMP Key Source
00, 01, 02 ... 17 ... 31
Remote Control
Component or SCART
Picture Orientation: Auto, Floor Front,
Ceiling Front, Floor Rear or Ceiling Rear
Installation
Display Device - Configure
White, Red, Green, Blue, Yellow, Cyan,
Magenta
Diagnostics
Altitude
Auto / High
Auto, REC601, REC709,
RGB-PC or RGB-Video
(Not available on S-Video or Composite
video inputs)
Color Space
Triggers
1 / 2 / 3
English, Français, Deutsch, Italiano.
Español, Svenska, Traditional Chinese,
Simplified Chinese, Português or
Russian
Language
Service
OSD Timer
0 (no timeout) or 5, 6, 7 ... 15 ... 60 sec.
OSD Messages
Blank Screen Color
Sidebar Color
On / Off
Miscellaneous
Red/Green/Blue = 0, 1, 2, 3 ... 255
Film Mode
(SD sources only)
On / Off
On / Off
CUE
(Chroma Upsampling Error)
(HD 1, HD 2 and Component inputs
only)
Sync Threshold
0, 1, 2 ... 15
HDMI EDID Extension
HDMI 1 / HDMI 2
Logo LED
Standby LED
LCD
On / Off
0 (off), 1, 2 ... 31
On / Off
Front Panel Brightness
0 (off), 1, 2, 3 or 4
On / Off
Enable
Auto Power Off
System Reset
Hours
1, 2, 3, 4, ... 8 ... 23, 24
Main Menu
The Main Menu is the starting point for accessing all DHD Controller functions.
(You must enter a passcode to access the Calibration and Service menus.)
➤
Runco Video
Input Source
Aspect Ratio
Picture
Input Position
Memory Presets
Information
Calibration
Service
48
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Main Menu, select Input Source to choose a video signal source.
Input Source
Input Source
The active source is indicated by an arrow (Î) to its left; in this example, Composite is the
active source.
Î
Composite
S-Video 1
S-Video 2
Component
HD1
HD2
SCART
HDMI 1
HDMI 2
To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio
from the Main Menu and press ENTER. Select the appropriate aspect ratio for your
screen size and the type of program material being viewed; refer to Table 4-1.
Aspect Ratio
Aspect Ratio
16:9
7
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
The currently-selected aspect ratio is indicated by a “7” to its left; in this example, 16:9 is
4:3
selected.
Letterbox
VirtualWide
Cinema
Virtual Cinema
Native
Note that some aspect ratios are unavailable and/or not useful with certain types of
source material. The optimal setting depends on a number of factors, such as:
• The aspect ratio of the source material, as broadcast or encoded on the playback
medium.
• The “display type” (16:9 or 4:3) and output resolution settings at the source
component. Most modern DVD/BD players and set-top boxes have such controls.
• Viewer preference (original aspect ratio with “black bars,” or a full-screen presentation
with some distortion or cropping).
The aspect ratio selection is automatically saved for each input and
resolution.
Note
Q-750d Series Installation/Operation Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings
Remote
Aspect Ratio Control
Key
Description
16:9
16:9
Select 16:9 to view 16:9 DVDs
and HDTV programs in their
native aspect ratio.
16:9 Image on
16:9 Screen (Display)
4:3 images are stretched
horizontally to fit a 16:9 screen.
4:3 Image, stretched to fill
16:9 Screen (Display)
4:3
4:3
Standard 4:3 scales the input
signal to fit in the center of the
16:9 screen. 4:3 is the aspect
ratio used by computer
monitors, standard television
programming and most VHS
video cassettes.
4:3 Image on
16:9 Screen (Display)
Letterbox
LBOX
Letterbox mode scales (zooms
in on) a 4:3 image linearly (by the
same amount on all sides) to fill
a 16:9 display.
Letterbox is best suited for
viewing LaserDisc movies or
non-anamorphic DVDs on a
16:9 screen.
4:3 Image on
16:9 Display
(Letterbox aspect ratio)
VirtualWide
VWIDE
VirtualWide scales a 4:3 image
NON-linearly (more on the sides
than in the center) to fit a 16:9
screen.
4:3 Image on
16:9 Screen (Display)
4:3 Image on
16:9 Screen
with VirtualWide
On a 2.35:1 screen, the image is
centered between black bars on
either side.
4:3 Image on
2.35:1 Screen
with VirtualWide
50
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Remote
Aspect Ratio Control
Key
Description
Cinema
CINEMA
Select Cinema to view 2.35
source material in its native
aspect ratio.
With a 16:9 screen and a
non-CineWide projector (no
anamorphic lens), the upper and
lower portions of the screen are
masked, but the geometry of the
active image area is unchanged.
2.35:1 Image on
16:9 Screen
(Cinema aspect ratio / no CineWide)
With a 2.35:1 screen and a
CineWide-equipped projector,
the DHD Controller scales the
2.35:1 image so that the active
image area fills the 16:9 chip
surface, eliminating the black
bars. The secondary,
2.35:1 Image on
2.35:1 Screen
(Cinema aspect ratio / CineWide)
anamorphic lens then restores
the proper geometry to the
2.35:1 image.
Virtual Cinema
SVC
A 16:9 image is scaled
NON-linearly (more on the sides
than in the center) to fit a 2.35:1
screen.
2.35:1 Screen
16:9 Image on
Virtual Cinema is available only
on CineWide-equipped
projectors.
16:9 Image on
2.35:1 Screen with
Virtual Cinema
Native
(none)
Select Native to display the
source signal in its native
resolution, centered in the
display area with no re-sizing or
overscan.
1080i HDTV Image
This means, for example, that
720p HDTV programs will
display with unused pixels on all
sides: 320 on the left and right
sides and 180 above and below.
720p HDTV Image
With SDTV and EDTV sources,
the DHD Controller scales the
image horizontally to achieve a
16:9 aspect ratio.
Q-750d Series Installation/Operation Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
Use the controls in the Picture Menu to calibrate each DHD Controller input to achieve
optimum picture quality.
➤
Picture
The DHD Controller has been designed to incorporate setup and calibration standards
established by the Imaging Science Foundation (ISF). The ISF has developed carefully
crafted, industry-recognized standards for optimal video performance and has
implemented a training program for technicians and installers to use these standards to
obtain optimal picture quality from Runco video display devices. Accordingly, Runco
recommends that setup and calibration be performed by an ISF certified installation
technician.
Brightness
Contrast
Color
Tint
Sharpness
Noise Filter
All signal types require separate processing. Therefore, you need to calibrate each DHD
Controller input separately.
1. When you change a picture quality setting, save the change to a
Note
preset afterwards. Otherwise, the change will be lost when a
different input is selected. (Picture quality settings are saved for
each input separately.) For information about saving settings,
2. For best results, Runco recommends that you set
ConstantContrast to Off before adjusting Brightness, Contrast
and other image quality settings in this menu (refer to
ConstantContrast on page 62). After you have completed the
initial calibration, set ConstantContrast to On if desired.
Although it may be possible to obtain satisfactory picture quality using the naked eye and
regular program material, Runco recommends using an external test pattern source
(Ovation Multimedia, Digital Video Essentials or AVIA test DVD or equivalent) for best
results.
Connect your test pattern source to the input that you are calibrating and proceed as
follows. Perform the adjustments in the order listed here.
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an
pattern.
Below Black
Above Black
Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness
52
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUGE patterns vary but generally consist of some combination of black, white and gray
areas against a black background. The example above includes two vertical bars and four
shaded boxes.
Select Brightness from the Picture menu and press ENTER. Adjust the brightness so that:
• The darkest black bars disappear into the background.
• The dark gray areas are barely visible.
• The lighter gray areas are clearly visible.
• The white areas are a comfortable level of true white.
• The image contains only black, gray and white (no color).
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the
one shown in Figure 4-3.
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast and press ENTER. Adjust the contrast to a point just below which the
white rectangle starts to increase in size.
Brightness and contrast controls are interactive. A change to one
may require a subtle change to the other in order to achieve the
optimum setting.
Note
Q-750d Series Installation/Operation Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Saturation: On your external test pattern source, select a color bar pattern like the
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
1. Press the MENU button on the remote control or DHD Controller front panel.
5. Press ENTER again to select Configure.
color channel.
8. Press RETURN (or MENU) repeatedly to return to the Main Menu.
54
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
11.Adjust the color saturation level until the outermost (gray and blue) color bars appear to
be a single shade of blue:
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image.
When tint is decreased, the image appears redder; when it is increased the image
appears greener.
and magenta color bars (on either side of the green bar) appear to be a single shade of
blue.
Like the brightness and contrast controls, the color and tint controls
are interactive. A change to one may require a subtle change to the
other in order to achieve the optimum setting.
Note
Q-750d Series Installation/Operation Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust
sharpness, select Sharpness from the Picture menu and press ENTER. On your external
looking for white edges around the transitions from black to gray and differently-sized lines
in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate
them.
Figure 4-5. Typical Test Pattern for Adjusting Sharpness
Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Picture
menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.
Use the left- or right-arrow buttons to select the desired amount of noise reduction,
keeping in mind that higher settings (which reduce high frequencies) may also “soften” the
image.
Input Position
Use the controls in the Input Position Menu to fine-tune the aspect ratio and image
position for the current source.
➤
Input Position
Left/Right
Up/Down
Width
The input position settings are automatically saved for each input
and resolution.
Note
Height
Left/Right: Select Left/Right from the Input Position menu to shift the projected image
horizontally. Press to shift the image to the right; press to shift it to the left.
Overscan
Overscan Mode
Phase
Up/Down: Select Up/Down from the Input Position menu to shift the projected image
vertically. Press to shift the image upward; press to shift it downward.
Tracking
Width: Select Width from the Input Position menu to change the projected image width.
Press to increase the width; press to decrease it.
Height: Select Height from the Input Position menu to change the projected image
height. Press
to increase the height; press
to decrease it.
56
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Overscan/Overscan Mode: Overscan pushes the outside edge of the active picture
area of the video signal out beyond the edge of the display area.
Some television programs are produced based on the assumption that older television
sets may not display the outer edges of the broadcast picture area. Overscan effectively
trims away these inactive, outer edges and enlarges the remaining portion of the image to
fill the display area.
For HDTV, DVDs and other video sources, Overscan is generally not necessary or
desirable.
This control defines the amount of overscan applied to the image. The range is from
0 to 20. There are two overscan modes:
• In Crop mode, each increment adds a mask at the top, bottom, left and right edges of
the source image equal to 0.5% of the displayed horizontal resolution (1% total). A
setting of 10, for example, crops the image 5% on all sides or 10% total.
• In Zoom mode, each increment adds a factor to the scaling of the source image so
that the vertical and horizontal resolutions are 100% plus 1% increments of the size
determined by the aspect ratio function. A setting of 10, for example, zooms in on the
image 5% on all sides or 10% total.
Figure 4-6 illustrates the effect of each overscan mode setting.
No Overscan
Crop
Zoom
4:3
16:9
= Source Image Area
= Mask (Crop) Area
= Screen (16:9)
Figure 4-6. Overscan Modes
Q-750d Series Installation/Operation Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Phase (RGB, Component or SCART sources): This control adjusts the phase of the
pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB,
Component or SCART image still shows shimmer or “noise” after Tracking has been
optimized.
Adjust the Phase after adjusting Tracking (see below).
Tip
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image. Adjust the
slidebar until the image stabilizes and each pixel is clearly defined. You may notice that
you can stabilize the image at more than one point. Use either setting in such cases.
Tracking (RGB, Component or SCART sources): Tracking determines the frequency
of the pixel sampling clock, indicated by the number of incoming pixels per line, so that all
pixels generated by a particular source are sampled.
Steady flickering or several soft vertical stripes or bands across the entire image indicates
poor pixel tracking. Proper pixel tracking helps ensure that the image quality is consistent
across the screen, that aspect ratio is maintained and that pixel phase (see above) can be
optimized.
Memory Presets
For each input, the DHD Controller lets you save image quality settings as presets that you
can recall at a later time. You can create up to four presets per input and display mode
(resolution and frame rate).
➤
Memory Presets
ISF Night
Î
The DHD Controller stores the following display modes in each memory preset:
ISF Day
• 480i
Custom 1
Custom 2
Save
Save
Reset
Reset
• 480p
• 576i
• 576p
• 720p/24 Hz
• 720p/25 Hz
• 720p/30 Hz
• 720p/50 Hz
• 720p/60 Hz
• 1080i/50 Hz
• 1080i/50 Hz (Australia)
• 1080i/60 Hz
• 1080p/24 Hz
• 1080p/25 Hz
• 1080p/30 Hz
• 1080p/50 Hz
• 1080p/60 Hz
Use the Memory Presets menu to recall saved image presets, or to save image settings in
the “Custom 1” or “Custom 2” memory location. The currently-selected preset is indicated
by a “Δ to its left; in the example shown here, ISF Night is selected.
58
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
You should save changes to any of the following settings to a preset; otherwise they will
be lost when a new input source or resolution is selected:
• Brightness
• Contrast
• Color saturation
• Tint
• Sharpness
• Gamma
• Color temperature and white balance
To select a memory preset, press
or
to highlight it and press ENTER.
To save the settings for the current input and display mode to the Custom 1 or Custom 2
memory preset, select it, press or to highlight Save and press ENTER.
To save the settings for the current input and display mode to the
ISF Night or ISF Day memory preset, select Save ISF Night or Save
ISF Day from the Calibration menu (refer to Save ISF Night/Save
Note
To reset the Custom 1 or Custom 2 memory preset to its factory-default state, select it,
press or to highlight Reset and press ENTER.
Press or to select Off, 30 Minutes, 60 Minutes, 90 Minutes, 2 Hours or 4 Hours.
Then, press ENTER.
Î
Off
30 Minutes
60 Minutes
90 Minutes
2 Hours
4 Hours
Q-750d Series Installation/Operation Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
Signal / System: Select Information from the Main Menu, then choose either Signal or
System to display information about the current input signal (resolution, frequency, type et
cetera) and installed firmware versions, as well as other information that uniquely identifies
your DHD Controller and display device.
➤
Information
Signal
System
Should you ever need to contact Runco Technical Support, this information will help them
answer your questions or resolve product performance issues.
Field Service
Manufacturing
System
DHD3
Q-750d
Signal
Model
Input Source
Signal Format
HDMI 1
Display Name
1080p/60
1920x1080
59.94 Hz
67.500 kHz
148.500 MHz
REC709
Output Resolution 1920x1080
Input Resolution
Vertical Freq
Horizontal Freq
Pixel Clock
Serial Number
Boot Version
00000000
3.0
Firmware Version 3.4
Micro Version 3.3
Color Space
Sync Type
Separate
Memory Preset
ISF Night
Field Service / Manufacturing: The Field Service and Manufacturing menus are
password-protected and intended for use only by Runco service personnel and factory
technicians.
Calibration
Use the Calibration menu to perform advanced picture quality adjustments. This menu
should be used by ISF-certified technicians only.
➤
Calibration
You must enter a passcode to access the Calibration menu.
ISF Settings
Display Color
Input Image
Note
Input Color
To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the
Save ISF Night
Save ISF Day
Copy/Paste
Display Color: Use the Display Color settings to adjust the color balance at the DHD
Controller output. These settings are saved independently for each input and display
mode.
Output Shift
Splash Configure
OSD Position
• Gain: Use the Gain controls to correct color imbalances in the bright areas of the
image. A good way to do this is to use a test pattern consisting mostly of solid white
areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red (Pr),
green (Y) or blue (Pr), decrease the Gain for that color.
• Offset: Use the Offset controls to correct color imbalances in the dark areas of the
image. A good way to do this is to use a test pattern consisting mostly of dark gray
areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red (Pr),
green (Y) or blue (Pr), decrease the Offset for that color.
• Gamma: Select Gamma from the Display Color menu to choose a DLP de-gamma
curve. The available settings are 1.8, 2.0, 2.2, 2.35 and 2.5.
Used correctly, the Gamma control can improve contrast while maintaining good
details for blacks and whites.
60
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
If excess ambient light washes out the image and it becomes difficult or impossible to
see details in dark areas, lower the gamma setting to compensate. This improves
contrast while maintaining good details for blacks. Conversely, if the image is washed
out and unnatural, with excessive detail in black areas, increase the setting.
• Color Temp: Select Color Temp from the Display Color menu to adjust the color
temperature. Color temperature establishes the “color of gray” by adjusting the 75%
white point to various color points.
What are “color points?” A “color point” is an x/y coordinate pair that defines a
stands for “Commission Internationale de l’Éclairage” (International Commission on
Illumination), the organization responsible for color measurement and management
standards.)
1.0
y
0.9
0.8
0.7
0.6
0.5
0.4
D50
D65
D93
0.3
0.2
0.1
0.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
x
1.0
Figure 4-7. CIE 1931 Chromaticity Diagram
• Simple: Select Simple mode from the Color Temp menu (with the Q-750d, this is
the only choice) to choose one of four color temperature presets: 5500K, 6500K,
7500K and 9300K. The default setting, 6500K, is appropriate for most situations.
Higher settings produce a “bluer” picture; lower ones impart a reddish hue to the
image.
Q-750d Series Installation/Operation Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-2 lists the x- and y-coordinates for each color temperature preset.
Table 4-2. Color Temperature Presets and Associated Color Points
Associated x/y Values
Color Temperature Preset
x
y
5500K
6500K
7500K
9300K
0.332
0.313
0.299
0.284
0.348
0.329
0.315
0.298
• ConstantContrast: Select ConstantContrast from the Display Color menu to enable
(Low/Medium/High) or disable (Off) ConstantContrast in the optical engine.
ConstantContrast uses a dynamic iris that modulates light to the DMD based on the
actual content of the video material. Runco recommends that you disable
ConstantContrast before adjusting Brightness, Contrast or other image settings.
gamut (range) that may be different from the default color gamut.
Each setting defines the precise hue of each primary (red, green and blue) and
secondary (yellow, cyan and magenta) color component used to generate the millions
of colors produced in displays. Changing this setting relocates the “triangle” for
moves the color closer to either orange or violet, which in turn affects all displayed
colors having a red component.
modes on a given input.
Note
• Auto automatically chooses the appropriate color gamut:
• SMPTE-C for NTSC, 480i and 480p sources.
• EBU for PAL, SECAM, 576i and 576p sources.
• REC709 for all other sources.
• REC709 chooses the REC709 color gamut.
• Select SMPTE-C to use the color gamut defined in SMPTE 170M-1999.
• Select EBU to use the color gamut defined in EBU Tech. 3213-E.
• Select Native for Runco's recommended Personal Color Equalizer preset for typical
video sources. It displays the fully saturated LED color gamut with appropriate color
brightness, hue, and Runco Smart Color settings.
• Select DCI to use the color gamut defined in Digital Cinema System Specification
Version 1.2.
• Select PCE to use the Personal Color Equalizer feature of the Q-750d. PCE lets you
do this.
62
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-3 lists the x- and y-coordinates for each primary and secondary color component.
Table 4-3. x/y Color Gamut Values
Color Gamut Settings and Associated x/y Values
Primary
Color
REC709
SMPTE “C”
EBU
DCI
x
y
x
y
x
y
x
y
Red
0.640
0.419
0.300
0.225
0.150
0.321
0.330
0.505
0.600
0.329
0.060
0.154
0.635
0.421
0.305
0.228
0.155
0.318
0.340
0.506
0.595
0.326
0.070
0.162
0.640
0.418
0.290
0.220
0.150
0.328
0.330
0.502
0.600
0.329
0.060
0.158
0.680
0.425
0.265
0.205
0.150
0.342
0.320
0.548
0.690
0.360
0.060
0.154
Yellow
Green
Cyan
Blue
Magenta
• PCE: To use the Personal Color Equalizer to define a custom color gamut, choose the
a given input.
Note
Q-750d Series Installation/Operation Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
• Hue/Saturation/Level: PCE provides the ability to define a custom color gamut in
terms of primary (red, green and blue) and secondary (yellow, cyan and magenta)
color hues, saturation and level (brightness).
Each control operates only on the color specified. Surrounding colors are linearly
interpolated based on their distance from each of these colors. In the CIE 1931 Yxy
white point, Saturation adjusts the coordinate's distance from white and Level
adjusts the luminance (Y) of the color relative to white.
Hue
Saturation Controls
• RSC™ (Runco Smart Color): Set RSC to On to to improve the accuracy of flesh
tones and increase color saturation, without sacrificing the purity of other colors.
• White Balance: To precisely adjust the white point associated with the custom
color gamut, choose White Balance from the PCE sub-menu. These controls
64
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
passcode.
The Input Image settings establish the “zero point” for the Picture
Note
menu settings, whose values represent offsets from the Input
Image settings. For example, if you set Brightness to 10 in this
actual setting value of 20 (10+10).
Input Color: The Input Color controls are similar to those in the Display Color menu (see
above), but adjust the color balance of the incoming signal. These settings are also saved
independently for each input and display mode.
• Gain/Offset (HD1, HD2 and Component/SCART inputs only): These controls
the Y, Pb and Pr signal components rather than the red, green and blue channels.
• Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a
Composite or S-Video source. Chroma delay in an image causes color shifts to occur
to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect.
If necessary, adjust this setting to eliminate them.
• Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the
Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i
video sources.
Use the left- or right-arrow buttons to select the desired amount of noise reduction,
keeping in mind that higher settings (which reduce high frequencies) may also “soften”
the image.
Save ISF Night/Save ISF Day: Whenever you make a change to the ISF settings, you
should always save it. Select Save ISF Night or Save ISF Day from the Calibration menu to
do this.
Copy/Paste: You can copy and paste settings from one memory location to another.
This gives you a convenient starting point for creating a new preset based on an existing
one, to make the calibration process less time-consuming.
Copy/Paste
Copy Settings
Paste Settings
For example, you can use the Copy/Paste feature to:
• Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
• Calibrate an input for 720p source signals, then use those settings for 1080i sources.
Copied From:
Input Source
Signal Format
Memory Preset
HDMI 1
• Duplicate ISF Night settings for a given source and signal format and save them in the
Custom 1 memory preset.
1080p/60
ISF Night
To use this feature, select Copy/Paste from the Calibration menu.
• Copy Settings: Select Copy Settings from the Copy/Paste menu to place the settings
for the current input source, signal format (resolution and frame rate) and memory
preset onto a “clipboard,” which is a temporary memory location. When you do, the
message “Settings Copied” briefly appears on-screen. The Copy/Paste menu then
re-appears, indicating the source of the copied settings.
Copied settings are not retained after a power cycle.
Note
Q-750d Series Installation/Operation Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
• Paste Settings: To apply the settings on the clipboard to a different input source,
signal format and/or memory preset, do any or all of the following:
• Switch to another DHD Controller input (for example, from HD1 to HD2).
• Change the output signal format at the source (for example, from 720p/60 to
1080i/60).
• Switch to another Memory Preset (for example, from ISF Night to Custom 1).
Then, select Paste Settings from the Copy/Paste menu. If you want to keep these
Position menu, except that they change the characteristics of the output signal. These
settings are saved independently for each aspect ratio.
Splash Configure: Use the Splash Configure menu to control the appearance and
behavior of the “splash” screen that appears on the display upon power-up.
• Owner Name/ISF Calibrated/ISF Other: You can have the Q-750d display the
owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up to
30 characters in length.
Use the up or down cursor button to select a character. Use the right and left cursor
buttons to change the cursor position. Press MENU when you have finished entering
text.
• Splash Timer: When you turn on the Q-750d, it projects a welcome screen with the
Runco and ISF logos, along with the personalized information you enter as described
above. Select Splash Timer from the Splash Configure menu to set the amount of time
for which this screen appears. The range is from 5 to 60 seconds, in one-second
increments. Press
or
to set the timer, then press MENU.
• Splash Enable: When you have finished customizing the splash screen, select Splash
Enable from the Splash Configure menu. Then, select On and press ENTER.
OSD Position: To adjust the position of the OSD, select OSD Position from the
Calibration menu and press ENTER.
Press
or
to select “Hor.” or “Ver.” Then, press
or
to change the position.
Service
Use the Service menu to access advanced projector configuration settings. This menu
should be used by ISF-certified technicians only.
➤
Service
Test Video
You must enter a passcode to access the Service menu.
Note
Input Names
Remote Control
Display Device
Color Space
Test Video: Select Test Video from the Service Menu to access the internal test patterns
on the DHD Controller. Four patterns are available: Horizontal Ramp, Vertical Ramp, Color
Bars 1 (solid bars) and Color Bars 2 (SMPTE “checkerboard” pattern).
Triggers
Miscellaneous
Sync Threshold
HDMI EDID Extension
Front Panel Brightness
System Reset
Press MENU to exit test pattern mode.
66
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Input Names: You can give each DHD Controller input a descriptive name. For example,
you may want to change the default input name to the type of source component
connected to it: “VCR,” “DVD,” “Laptop” et cetera. Input names can be up to 12
characters long.
Input Names
Restore
C o m p o s i t e
Composite
S-Video 1
S-Video 2
Component
HD 1
S - V i d e o
S - V i d e o
1
2
To edit an input name, select Input Names from the Service menu. Press or to select
an input and press ENTER. Use the
or
press ENTER or MENU.
or
buttons to change a character; press
to select a character to change. When you have finished editing the input name,
C o m p o n e n t
H D
H D
1
2
HD 2
To restore the default input name, press
repeatedly to highlight that input name in the
S C A R T
H D M I
SCART
“Restore” column. Then, press ENTER.
1
2
HDMI 1
H D M I
HDMI 2
Remote Control: Select Remote Control from the Service menu to change the following
settings related to remote control operation.
• Remote Code: Select Remote Code from the Remote Control menu to set the
infrared (IR) code set to which the DHD Controller will respond. By default, it is set to
17. You can change this setting if either:
• Another device in the theater (a DVD player, for example) is responding to
unpredictable or undesirable.
• You have multiple DHD Controllers and want to control them independently, as
opposed to broadcasting commands from a single remote to all of them. In this
scenario, you can use multiple remotes programmed to use different IR codes. Or,
you can use a single remote and change the IR code as needed to address a
specific DHD Controller.
Use the DHD Controller front-panel keypad to change the IR code to
which the controller will respond. Then, change the code sent by the
remote to match as described below.
Tip
When you change a remote code on the DHD Controller, you must re-program the
DHD Controller remote control to send that same code. To do this:
1. Press and hold the LIGHT button on the
remote control for approximately three
seconds, or until the LED on the remote lights
solid red.
RETURN
EXIT
2. Enter a new two-digit code between 00 and 31
inclusive. Include a leading zero for single-digit
codes; for example, enter 9 as “09.”
3. The LED turns off to confirm the code change. If you enter an invalid code, the LED
flashes for three or four seconds. Try again, entering a valid code.
• COMP Key Source: Select COMP Key Source from the Remote Control menu to
assign the COMP remote control button to either the Component or SCART input.
Q-750d Series Installation/Operation Manual
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Device - Configure: The options in the Display Device - Configure menu allow
you to change the picture orientation, perform lens adjustments or access other,
display-device specific functions.
• Installation – Orientation: Select Installation from the Display Device - Configure
menu, then select Orientation to change the picture orientation to suit the method of
installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear). Or, for
front-projection installations, use the Auto setting to have the projector automatically
determine the orientation (floor or ceiling) using an internal sensor.
• Diagnostics: Select Diagnostics from the Display Device - Configure menu, then
select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color channel
(simulating a filter of that color). This can be useful for calibration or measurement
purposes.
To restore the normal picture (all colors), select White.
• Altitude: Select Altitude from the Display Device - Configure menu to control the
operation of the projector’s cooling fan.
In most cases, the default setting (Auto) maintains the correct operating temperature. If
the projector frequently turns off due to overheating, or in certain high-altitude operating
environments, you may need to change this setting to High.
Color Space: Select Color Space from the Service menu to choose the color space of
the source signal for HDMI, RGB, and component connections.
• The default setting, Auto, functions as follows:
• HDMI: If the Auxiliary Video Information (AVI) infoframe contains color space and/or
range data, the DHD Controller uses that information. Otherwise, for RGB sources,
the DHD Controller uses the RGB-Video color space. For component SDTV and
EDTV resolutions, REC601 is used. For other component video resolutions,
REC709 is used.
• RGB: If Hsync or Vsync signals are present, the DHD Controller uses the RGB-PC
color space. Otherwise, REC601 is used for SDTV and EDTV sources, and REC709
for all other sources.
• Component: For SDTV and EDTV resolutions, the DHD Controller uses the
REC601 color space. For all other resolutions, REC709 is used.
In most cases, the Auto setting determines the correct color space to use. If it does not,
you can force the DHD Controller to use a specific color space. Choose one of the
following:
• REC709 sets the color space matrix to that defined in ITU-R BT.709.
• REC601 sets the color space matrix to that defined in ITU-R BT.601.
• RGB-PC uses RGB color space and sets black at 0,0,0 RGB and white at
255,255,255 RGB, assuming an 8-bit image.
• RGB-Video uses RGB color space and sets black at 16,16,16 RGB and white at
235,235,235, assuming an 8-bit image, to correspond to the luminance values defined
in digital component standards.
Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs.
You can assign one or more trigger outputs to each aspect ratio. Those triggers are then
activated by selecting that aspect ratio.
With a Q-750d/CineWide with AutoScope, assign at least one trigger output (the same
one to which the lens motor is connected) to the Cinema and Virtual Cinema aspect
ratios.
68
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous: Select Miscellaneous from the Service menu to set the following options:
• Language: Select Language from the Miscellaneous menu and press the up- or
down-arrows to select the OSD Language (English, Français, Deutsch, Italiano,
Español, Svenska, Traditional Chinese, Simplified Chinese, Português or Russian).
• OSD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD Timer,
which controls how long the menus remain on-screen after selecting them. Select from
5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want
the menus to remain on-screen indefinitely.
• OSD Messages: When you select a new aspect ratio, input source or memory preset,
the DHD Controller briefly displays an on-screen message confirming your new
selection. To prevent the display of these messages, select OSD Messages from the
Miscellaneous menu to and set it to Off.
• Blank Screen Color: Select Blank Screen Color from the Miscellaneous menu to
select the color that appears when no incoming signal is present. The range is from 0
to 255 inclusive for each color component (red, green and blue).
• Sidebar Color: Select Sidebar Color from the Miscellaneous menu to change the
color of the inactive image area. The range is from 0 to 255 inclusive for each color
component (red, green and blue). The inactive image area is on either side of the active
image area when using the 4:3 aspect ratio.
• Film Mode: Use Film Mode to smooth out moving images from interlaced,
standard-definition (SD) sources. In most cases, the DHD Controller detects the proper
“pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing
you may want to enable Film Mode to ensure stable processing for that source.
• CUE (Chroma Upsampling Error) Correction: Some DVD players use MPEG
decoders that do not correctly “upsample” the 4:2:0 format chroma information on the
DVD to the 4:2:2 or 4:4:4 format required by the video encoder of the display device.
This so-called “chroma bug” sometimes causes streaky or spiky horizontal lines
running through the chroma channel. It is most noticeable in static, interlaced scenes
and on diagonal edges (especially red ones). Set CUE to On to correct this issue.
Sync Threshold: Select Sync Threshold to adjust the threshold at which negative pulses
on the component video green/luma channel are interpreted to be sync pulses.
Sync Threshold adjustment is occasionally necessary when a DVD player or HDTV source
signal drops “below black” (for example, during scenes with explosions or when subtitles
are present) and causes the projector to temporarily lose sync. If the sync level from the
source is persistently too low, the display device won’t sync with the source at all.
The range is from 0 (approximately 60 millivolts (mV)) to 15 (approximately 256 mV).
HDMI EDID Extension: Extended display identification data (EDID) is a data structure
provided by a display device to describe its capabilities to a graphics card. It is what
enables a modern personal computer to know what kind of monitor is connected.
Some modern display devices provide more information via EDID than others, in the form
of “extensions.” Some computer graphics cards do recognize or properly interpret this
extended EDID information.
Select HDMI EDID Extension from the Service menu to specify whether or not the EDID
extensions from the display device are passed through to the sources connected to the
HDMI 1 or HDMI 2 inputs. By default, the extensions are on. Change these settings only if
HDMI EDID incompatibility issues arise.
Q-750d Series Installation/Operation Manual
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Brightness: Select Front Panel Brightness from the Service menu to adjust
the brightness of the front-panel LED and LCD status indicators.
Standby LED
LCD
Logo LED
• Logo LED: Select Logo LED from the Front Panel Brightness menu to adjust the
brightness of the large, illuminated logo on the left side of the display. The range is from
0 (off) to 31.
• Standby LED: Select Standby LED from the Front Panel Brightness menu to change
the behavior of the front-panel STANDBY indicator LED. When set to ON, the LED
lights amber when the system is in standby mode; otherwise, it is off. When set to OFF,
the LED is always off.
• LCD: Select LCD from the Front Panel Brightness menu to adjust the brightness of the
front-panel LCD. The range is from 0 (off) to 4.
itself off after a period of inactivity (no source signal present).
Auto Power Off sub-menu and set it to On.
System Reset: To reset ALL controller settings (including image settings) back to their
factory defaults, choose System Reset from the Service menu.
A confirmation message appears. Select Yes to continue with the reset or select No to
cancel.
This action is not undoable. Proceed with caution! Before you
perform a System Reset, save your “Custom” Memory Presets
Caution
70
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Maintenance and Troubleshooting
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the Q-750d. If you encounter an issue not described here, please contact
Runco Technical Support.
5.1
Troubleshooting Tips
Table 5-1. Troubleshooting Chart
Symptom
Possible Cause(s)
Solution
Neither the DHD Controller
nor the projector turns on.
Both front-panel LEDs on the
DHD Controller are off (see
• The DHD Controller is not
plugged in or the AC outlet
is not active.
• Ensure that the DHD
Controller is plugged in
and that the AC outlet is
active.
• Set the switch to the “on”
position.
• The main power switch at
the rear of the DHD
Controller (see Figure 2-4)
is set to the “off” position.
Neither the DHD Controller
nor the projector turns on. On
the DHD Controller, the
Runco icon LED is off and the
standby LED is on.
• The batteries in the remote
control are dead or
• Press the ON/STANDBY
(
) button on the DHD
installed incorrectly.
Controller front panel. If
the controller turns on,
verify that the batteries in
the remote control are
good and properly
installed (refer to Remote
The DHD Controller turns on,
but the projector does not.
• The DHD Controller is
connected to the Q-750d
incorrectly or not at all.
• Verify the RS-232 cable
connection from the DHD
Controller to the Q-750d
• The Q-750d is not plugged
in or the AC outlet is not
active.
• Ensure that the Q-750d is
plugged in and that the AC
outlet is active.
The projector and DHD Con-
troller are both on and menus
appear, but there is no video
image on-screen.
• Incorrect source selection.
• Source component is not
turned on.
• Select the correct source.
• Turn on the source
component.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high.
• Brightness is set too high.
• Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Lower the brightness
setting.
Q-750d Series Installation/Operation Manual
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. Troubleshooting Chart (continued)
Symptom
Possible Cause(s)
Solution
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
• The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
DHD Controller.
• Ensure that the source
outputs are connected to
the correct DHD Controller
input.
Image geometry is incorrect.
• Incorrect aspect ratio
selection.
• Select the aspect ratio that
best matches the source
image and screen size
(refer to Table 4-1).
72
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. External Control
In addition to using the DHD Controller front-panel keypad or remote control unit, there
are two methods of controlling the Q-750d and DHD Controller externally:
• Using a serial (RS-232) link to send ASCII commands and receive responses to those
commands.
• Using discrete infrared (IR) codes to program a third-party remote control unit.
The following sections describe both of these methods.
The DHD Controller uses a simple text-based control protocol to take requests from
control devices and to provide responses to such devices. This section describes how to
send control messages over a serial link between the DHD Controller and an
automation/control system or a PC running terminal emulation software.
6.1
Serial Communications
To interface the Q-750d with an automation/control system or a PC running terminal
emulation software, connect it to the Display Control output of the DHD Controller as
input of the DHD Controller as shown in Figure 3-17.
RS-232 Connection and
Port Configuration
Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop
bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller
RS-232 port.
Serial commands to the DHD Controller take the following form:
• Commands are not case-sensitive.
Serial Command Syntax
• For a single command that takes no parameters, type the command followed by a
carriage return; for example, to set the aspect ratio to Letterbox, type
LETTERBOX <Enter>.
• For a single command that takes a parameter, type the command, a space or a
comma and the desired value followed by a carriage return; for example, to set the
brightness to -10, type BRIGHTNESS -10 <Enter> or
BRIGHTNESS,-10 <Enter>.
• You can also send a string of multiple commands on a single line, separated by
commas. For example, COMPOSITE,BRIGHTNESS 50,16:9 <Enter> switches to
the Composite video input, sets the brightness to 50 and sets the aspect ratio to 16:9.
Command strings can be up to 255 characters long.
Avoid combining the ONor POWER 1commands with other commands
Note
on a single line. After sending ONor POWER 1, allow at least five (5)
seconds for the DHD Controller to power up. If you have enabled the
seconds for the DHD Controller to power up.
Once it does, it will accept and properly execute multiple serial
commands.
Q-750d Series Installation/Operation Manual
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1 lists the RS-232 command set. The “Parameter (min/max)” column shows the
valid parameter ranges, or “NA” for commands that take no parameters.
When you enter a valid command, the DHD Controller executes it and acknowledges it
with a plus sign on the command line (+ >). When you enter an invalid command – one
that is misspelled or followed by values outside the valid range for that command – the
DHD Controller ignores it and returns a minus sign (- >).
Table 6-1. Serial Commands
Parameter
(min/max)
Value
Stored?
Command
Description
Power On/Off Commands
OFF
ON
NA
NA
0/1
NA
NA
NA
NA
NA
Turns projector off
Turns projector on
POWER
Turns projector on and off
Returns power status
POWER?
Input Selection Commands
COMPONENT
COMPOSITE
HDMI1
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
YES
YES
YES
YES
YES
YES
NA
Selects the Component input
Selects the Composite video input
Selects the HDMI 1 input
Selects the HDMI 2 input
Selects the RGB HD 1 input
Selects the RGB HD 2 input
Returns active input
HDMI2
HD1
HD2
INPUT?
SCART
YES
YES
YES
Selects the SCART input
Selects the S-Video 1 input
Selects the S-Video 2 input
SVIDEO1
SVIDEO2
74
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Aspect Ratio Commands
16:9
4:3
NA
NA
NA
NA
NA
NA
NA
NA
YES
YES
NA
Selects the 16:9 aspect ratio
Selects the 4:3 aspect ratio
ASPECT?
Returns current aspect ratio
CINEMA
YES
YES
YES
YES
YES
Selects the Cinema aspect ratio
Selects the Letterbox aspect ratio
Selects the Native aspect ratio
Selects the VirtualWide aspect ratio
Selects the Virtual Cinema aspect ratio
LETTERBOX
NATIVE
VIRTUALWIDE
VIRTUALCINEMA
Picture Adjust Commands
BRIGHTNESS
BRIGHTNESS?
CHROMADELAY
CHROMADELAY?
COLOR
-50/50
NA
YES
NA
Sets a value for brightness
Returns brightness setting value
Sets a value for input color chroma delay
Returns input color chroma delay setting
Sets a value for color
-7/7
NA
YES
NA
-50/50
NA
YES
NA
COLOR?
Returns color setting value
CONTRAST
CONTRAST?
FILMMODE
-50/50
NA
YES
NA
Sets a value for contrast
Returns contrast setting value
Sets Film Mode off (0) or on (1)
0/1
YES
NA
FILMMODE?
NA
Returns Film Mode setting
(0 = off; 1 = on)
FILTER
0/10
NA
YES
NA
Sets a value for input color noise filter
Returns input color noise filter setting
Adjusts phase
FILTER?
PHASE
0/31
NA
YES
NA
PHASE?
SHARPNESS
SHARPNESS?
TINT
Returns phase setting value
Sets a value for sharpness
Returns sharpness setting value
Sets a value for tint
-50/50
NA
YES
NA
-50/50
NA
YES
NA
TINT?
Returns tint setting value
Q-750d Series Installation/Operation Manual
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Image Preset Commands
CUSTOM1
NA
NA
NA
NA
NA
YES
YES
YES
YES
NA
Loads “Custom 1” image preset
Loads “Custom 2” image preset
Loads “ISF Day” image preset
Loads “ISF Night” image preset
CUSTOM2
DAY
NIGHT
PRESET?
Returns currently-selected preset
(ISF Day, ISF Night, Custom 1 or Cus-
tom 2)
Input Position Commands
IHEIGHT
0/20
NA
YES
NA
Sets the value for input height
IHEIGHT?
IHPOS
Returns input height value
-50/50
NA
YES
NA
Sets a value for horizontal input position
Returns input horizontal position value
Sets a value for vertical input position
Returns input vertical position value
Sets the value for input width
IHPOS?
IVPOS
-50/50
NA
YES
NA
IVPOS?
IWIDTH
0/50
NA
YES
NA
IWIDTH?
Returns input horizontal width value
Sets the overscan percentage
OVERSCAN
OVERSCAN?
OVERSCANMODE
0/20
NA
YES
NA
Returns overscan percentage
0/1
YES
Sets the overscan mode (0=zoom;
1=crop)
OVERSCANMODE?
NA
NA
Returns the overscan mode (0=zoom;
1=crop)
Output Shift Commands
OHEIGHT
OHEIGHT?
OHPOS
-50/50
NA
YES
NA
Sets the value for output height
Returns output height value
-50/50
YES
Sets the value for output horizontal posi-
tion
OHPOS?
OVPOS
NA
NA
Returns output horizontal position value
Sets the value for output vertical position
Returns output vertical position value
Sets the value for output width
-50/50
NA
YES
NA
OVPOS?
OWIDTH
OWIDTH?
-50/50
NA
YES
NA
Returns output horizontal width value
76
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Parameter
(min/max)
Value
Stored?
Command
Description
Sleep Timer Commands
SLEEPTMR?
NA
NA
NA
NA
NA
NA
NA
NA
Returns sleep timer setting
STOFF
YES
YES
YES
YES
YES
YES
Sets the sleep timer to Off
ST30MIN
ST60MIN
ST90MIN
ST2HRS
ST4HRS
Sets the sleep timer to 30 minutes
Sets the sleep timer to 60 minutes
Sets the sleep timer to 90 minutes
Sets the sleep timer to 2 hours
Sets the sleep timer to 4 hours
Miscellaneous Commands
DISPLAY?
NA
NA
Returns display device input source
value, as follows:
1 = Auto
43 = Q-750d
INRES?
NA
NA
NA
NA
NA
0/4
NA
NA
NA
NA
NA
NA
Returns input resolution
MODEL?
OUTRES?
SERNUM?
SWVER?
SYSSTATE?
Returns product model name
Returns output resolution
Returns DHD Controller serial number
Returns software version number
Returns current system state
0 = Off
1 = Initializing
2 = On
3 = Powering Down
4 = Error
TRIGGER
1/3
YES
Assigns trigger to currently-selected
aspect ratio
The following serial commands are meant to emulate buttons on the remote control or DHD Con-
troller front panel. Each button has its own serial command, so effectively it is as if you were using
the IR remote only you’ll be doing so via serial commands. These commands provide active OSD
responses just like the IR remote.
DOWN
ENTER
EXIT
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
NA
Down-Arrow ( ) key
ENTER key
EXIT (RETURN) key
Left-Arrow ( ) key
MENU
LEFT
MENU
RIGHT
UP
Right-Arrow ( ) key
Up-Arrow ( ) key
Q-750d Series Installation/Operation Manual
77
Download from Www.Somanuals.com. All Manuals Search And Download.
The DHD Controller accepts commands in the form of IR signals that conform to the
Phillips RC5 protocol. Each DHD Controller remote control button has an RC5 control
code associated with it.
6.2
Using Discrete IR
Codes
You can use these codes to program a third-party, “universal” remote control unit to work
with the DHD Controller. These third-party products usually come with a computer
software application for this purpose. For more information, consult the documentation
provided with the remote control unit.
IR Command Protocol
The IR control codes have the following characteristics:
• Each code consists of 14 bits:
➤
• Two (2) start bits (always 1);
• A toggle bit. This bit is inverted every time a key is released and pressed again. This
enables the DHD Controller to distinguish between a button that remains down and
one that is pressed repeatedly.
• Five (5) address bits. The default address is 17 (binary 10001). To change it, select
• Six (6) data bits.
• The carrier frequency is 36 kHz, with the modulated pulses having a 25% duty cycle.
• Commands are sent at a maximum rate of 9 Hz.
For example, here is the RC5 control code for the ON button on the DHD Controller
remote control unit (assuming the default address is used):
With Toggle Bit = 0
Hex
3
3
4
4
4
1
1
Binary
1
1
1
1
0
1
1
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
1
1
With Toggle Bit = 1
Hex
C
Binary
1
0
0
0
Start
Bits
Toggle
Bit
Function
Address
Command
78
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6-1 shows the pulse train for this command (with the toggle bit set to zero).
Data
Word
S1 S2 TB A4 A3 A2 A1 A0 C5 C4 C3 C2 C1 C0
Address Bits
Command Bits
Start Bits Toggle Bit
Encoded
Data
Word
1
1
0
1
0
0
0
1
0
0
0
0
0
1
1.78 ms
Modulated
Carrier
Zoom In
of Carrier
tp
27.8 µs
3tp
First Packet
Repeated Packet
RC5 Packet
Transmission
14 cycles, 24.9 ms
64 cycles, 113.8 ms
Figure 6-1. RC5 Message Format
Table 6-2 lists the RC5 control codes for the DHD Controller.
IR Command List
Table 6-2. RC5 Control Codes for the DHD Controller
RC5 Data
RC5 Data
from
Remote Control
Button Name
with Toggle
Bit = 1
Remote
Control
(Note)
Description
(Note)
(none)
0x346E
0x3457
0x3449
0x344A
0x346C
0x344E
0x3C6E
0x3C57
0x3C49
0x3C4A
0x3C6C
0x3C4E
Native aspect ratio
(none)
16:9
SCART video input
16:9 aspect ratio
4:3
4:3 aspect ratio
CINEMA
COMP
Cinema aspect ratio
Component video input
Note: These codes assume that the default address of 17 is used. If you change it to something
other than 17, you will need to modify these codes accordingly.
Q-750d Series Installation/Operation Manual
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-2. RC5 Control Codes for the DHD Controller (continued)
RC5 Data
RC5 Data
from
Remote Control
Button Name
with Toggle
Bit = 1
Remote
Control
(Note)
Description
(Note)
CUST 1
0x3472
0x3473
0x3446
0x3444
0x3474
0x3451
0x3452
0x3453
0x3454
0x3471
0x3470
0x3447
0x344B
0x3443
0x3442
0x3441
0x3448
0x346D
0x344F
0x3450
0x3445
0x344D
0x344C
0x3C72
0x3C73
0x3C46
0x3C44
0x3C74
0x3C51
0x3C52
0x3C53
0x3C54
0x3C71
0x3C70
0x3C47
0x3C4B
0x3C43
0x3C42
0x3C41
0x3C48
0x3C6D
0x3C4F
0x3C50
0x3C45
0x3C4D
0x3C4C
Custom 1 memory preset
Custom 2 memory preset
CUST 2
DOWN
ENTER
EXIT
Down-Arrow (
)
ENTER
EXIT (RETURN)
HD 1
HD1 video input
HD 2
HD2 video input
HDMI 1
HDMI 2
ISF DAY
ISF NIGHT
LEFT
HDMI1 video input
HDMI2 video input
ISF Day memory preset
ISF Night memory preset
Left-Arrow (
)
LET BOX
MENU
OFF
Letterbox aspect ratio
MENU
Power off
ON
Power on
RIGHT
SVC
Right-Arrow (
)
Virtual Cinema aspect ratio
S-Video 1 video input
S-Video 2 video input
S-VID 1
S-VID 2
UP
Up-Arrow (
)
VIDEO
V-WIDE
Composite video input
VirtualWide aspect ratio
Note: These codes assume that the default address of 17 is used. If you change it to something
other than 17, you will need to modify these codes accordingly.
80
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Specifications
Table 7-1 lists the Q-750d specifications.
7.1
Q-750d Specifications
Table 7-1. Q-750d Specifications
Projector Type:
Illumination:
Digital Light Processing™ (DLP™),Single-Chip, 16:9
SuperOnyx™ DMD™ with InfiniLight Illumination
TM
TM
RGB InfiniLight LEDs for 135% NTSC color gamut with
TM
TM
Runco Smart Color and Personal Color Equalizer
Native Resolution:
Aspect Ratios:
Full HD, 1920 x 1080 (16:9)
Refer to Table 7-2
Video Standards:
Refer to Table 7-2
Video Compatibility:
Picture Size (16:9 Screen):
480i, 480p, 576i, 576p, 720p, 1080i 50/60, 1080p 24/50/60
Recommended Width: 72 in. (1.83 m) to 92 in. (2.34 m)
Maximum Width: 108 in. (2.74 m)
Throw Distance
Refer to Table 3-3
(Factor x Screen Width):
Vertical Offset:
Standard Q-750d - 60% of screen height above or below
lens center (120% of one half of the screen height)
Q-750d/CineWide or Q-750d/CineWide with AutoScope
- 25% of screen height (50% of one half of the screen height)
above or 60% of screen height (120% of one half of the screen
height) below lens center, when projector is inverted
Horizontal Offset:
12.5% of screen width left or right of lens center (25% of one
half of the screen width)
Inputs
(from DHD Controller):
(1) HDMI with HDCP
(1) RS-232
Q-750d Series Installation/Operation Manual
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-1. Q-750d Specifications (continued)
Brightness and Contrast:
Cinema Standards Measurement System (CSMS)
Specifications
-
-
Brightness: 29 foot-Lamberts (fL)
Contrast Ratio: 330:1
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to
ANSI/NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface. The
Society of Motion Picture and Television Engineers (SMPTE) specifies
16 fL as the target image brightness for film-based projectors using an
open gate (without film in the projector). More importantly, today
SMPTE specifies 12 fL as the target image brightness in Digital
Cinema theaters. The foot-Lambert measurement is dependent on
screen size, screen gain and projector light output.
Home Theater Calibration Specifications
-
-
Light Output: 450 ANSI Lumens
Contrast Ratio: 330:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
-
-
Light Output: 700 ANSI Lumens
Contrast Ratio: 3 settings (Infinity:1, 20,000:1, 10,000:1
(sequential))
ColorContrast™
Colors have up to 50% higher contrast than Mercury or Xenon
lamp systems.
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with other
manufacturers’ projectors. These measurements are typically taken at
9,000K to 13,000K to get expected performance data when the
projector is used in professional, commercial and industrial displays.
Power Requirements:
Operating Environment:
Dimensions:
100 to 240 VAC (auto-sensing), 50/60 Hz, 140 Watts typical
(477.8 BTUs/hour)
50°F to 104°F (10°C to 40°C), 0% to 85% humidity
(non-condensing)
Q-750d/CineWide with AutoScope: See Figure 7-2
Weight (including lens):
Regulatory Approvals:
49.4 lbs. (22.4 kg)
FCC Part 15 Class B, CE Class B, UL, cUL, CB, RoHS,
WEEE, local conformances as required
Limited Warranty:
Two (2) years parts and labor from the date of delivery to the
end user.
Maintenance:
Zero maintenance, solid state optical path.
Specifications are subject to change without notice.
82
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-2 lists the DHD Controller specifications.
7.2
DHD Controller
Specifications
Table 7-2. DHD Controller Specifications
Aspect Ratios:
4:3, Letterbox, 16:9, VirtualWide, Cinema, Virtual Cinema,
Native
Video Standards:
Inputs:
NTSC, PAL
(1) Composite
(2) S-Video
(1) Component/RGBHV/SCART (5 x RCA)
(2) Component/RGBHV (5 x BNC)
(2) HDMI with HDCP
Output:
HDMI 1.3 with HDCP
Control Options:
-
-
-
Discrete infrared remote
Serial commands via RS-232
Front-panel controls
RS-232 Communication
Parameters:
19200 bps, no parity, 8 data bits, 1 stop bit, no flow control
Trigger Outputs:
(3) +12 VDC, each rated at 250 mA and thermal
fuse-protected
Bandwidth:
150 Mega Samples per Second (MSPS)
Power Requirements:
Operating Environment:
100 to 240 VAC (auto-sensing), 50/60 Hz, 160 watts
41°F to 95°F (5°C to 35°C), 0% to 90% humidity
(non-condensing)
Dimensions:
Width = 17.50 inches (444.5 mm)
Depth = 11.19 inches (284.1 mm)
Height = 3.75 inches (95.3 mm)
Weight:
13.0 lbs. (5.90 kg)
Regulatory Approvals:
Limited Warranty:
Complies with FCC, CE C-Tick
Two (2) years parts and labor from the date of delivery to the
end user.
Specifications are subject to change without notice.
Q-750d Series Installation/Operation Manual
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-1 shows the Q-750d dimensions (all dimensions are in millimeters and [inches]).
7.3
Overall Dimensions –
Q-750d
Figure 7-1. Overall Dimensions – Q-750d
84
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-2 shows the Q-750d/CineWide with AutoScope dimensions (all dimensions are in
millimeters and [inches]).
7.4
Overall Dimensions –
Q-750d/CineWide with
AutoScope
Figure 7-2. Overall Dimensions – Q-750d/CineWide with AutoScope
Q-750d Series Installation/Operation Manual
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-3 lists the signal types supported by each input on the DHD Controller.
7.5
Supported Timings
Table 7-3. Supported Signal Timings by Input
Supported? (√ = Yes, – = No)
Horizontal
Refresh
Rate (Hz)
PixelFrequency
(MHz)
Format
640x480
800x600
Resolution
Frequency
(kHz)
60.00
66.59
72.00
75.00
85.00
60.00
72.00
75.00
85.00
74.54
47.95
60.00
60.00
70.00
75.00
85.00
75.00
47.95
60.00
60.00
75.00
85.00
60.00
85.00
31.469
35.892
37.861
37.500
43.269
37.879
48.077
46.875
53.674
52.849
25.270
31.020
48.363
56.476
60.023
68.677
67.500
37.833
47.396
47.776
60.289
68.633
60.000
85.938
25.175
29.862
31.500
31.500
36.000
40.000
50.000
49.500
56.250
60.036
27.089
33.750
65.000
75.000
78.750
94.500
108.000
64.769
68.250
79.500
102.250
117.500
108.000
148.500
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
640x480
800x600
832x624
848x480
832x624
848x480
1024x768
1024x768
1152x864
1280x720
1152x864
1280x720
1280x768
1280x960
1280x768
1280x960
86
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-3. Supported Signal Timings by Input (continued)
Supported? (√ = Yes, – = No)
Horizontal
Frequency
(kHz)
Refresh
Rate (Hz)
PixelFrequency
(MHz)
Format
Resolution
60.00
75.00
85.00
60.00
60.00
60.00
75.00
60.00
60.00
47.95
60.00
63.981
79.976
91.146
47.712
64.744
65.317
82.278
75.000
64.674
56.821
74.038
108.000
135.000
157.500
85.500
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1280x1024 1280x1024
1360x768
1360x768
101.000
121.750
156.000
162.000
119.000
150.007
154.000
1400x1050 1400x1050
1600x1200 1600x1200
1680x1050 1680x1050
1920x1080 1920x1080
1920x1200 1920x1200
SCART
–
50.00
–
–
–
–
–
√
–
–
RGBS
480/60i
480/60p
576/50i
720x487
720x483
720x576
720x576
59.94
59.94
50.00
50.00
15.734
31.469
15.625
31.250
13.500
27.000
14.750
29.000
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
√
√
√
√
√
√
√
√
√
√
√
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
√
√
√
–
–
–
–
–
–
–
–
–
–
–
–
–
–
√
√
√
576/50p
720/24p
720/25p
720/30p
720/50p
720/60p
1080/50i
1080/60i
1280x720 23.98/24.00 17.982/18.000 59.341/59.400
1280x720 25.00 18.750 74.250
1280x720 29.97/30.00 22.478/22.500 74.175/74.250
1280x720
1280x720
1920x1080
50.00
60.00
50.00
37.500
45.000
75.250
74.250
28.125/31.250 74.250/72.000
1920x1080 59.94/60.00 33.716/33.750 74.175/74.250
1080/24p 1920x1080 23.98/24.00 26.978/27.000 74.175/74.250
1080/50p 1920x1080 50.00 56.250 148.500
1080/60p 1920x1080 59.94/60.00 67.433/67.500 148.350/148.500
NTSC 3.58
NTSC 4.43
PAL-B/G/H/I
–
–
–
59.94/60.00 15.734/15.750
59.94/60.00 15.734/15.750
3.580
4.430
4.430
50.00
15.625
Q-750d Series Installation/Operation Manual
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-3. Supported Signal Timings by Input (continued)
Supported? (√ = Yes, – = No)
Horizontal
Frequency
(kHz)
Refresh
Rate (Hz)
PixelFrequency
(MHz)
Format
Resolution
PAL-M
PAL-N
SECAM
–
–
–
59.94/60.00 15.734/15.750
3.580
3.580
–
–
–
–
–
–
–
–
–
–
–
√
√
√
√
√
√
√
50.00
50.00
15.625
15.625
13.500
88
Q-750d Series Installation/Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
020-0997-00 Rev. A
November 2009
Runco International • (800) 23RUNCO • Fax (503) 748-8161 • www.runco.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Raritan Computer Switch TR361 User Guide
RCA Car Satellite TV System ANT3020X User Guide
Roland Computer Keyboard EM 15 OR User Guide
Saleen Window 10 8002 C12167A User Guide
Samsung Computer Monitor XL20 User Guide
Samsung DVR SVS 5R User Guide
Samsung Home Security System SSA C100 User Guide
Samsung Speaker System HW E450 User Guide
Sanyo Cell Phone SCP 7300 User Guide
Sanyo Projector PLV Z4 User Guide