Multimedia Projector
MODEL PLV-Z4
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Input Source and System Selection
24
Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
27
Image Adjustment . . . . . . . . . . . . . . . . . . . 28
Image Level Adjustment
28
Picture Adjustment . . . . . . . . . . . . . . . . . . 32
Picture Position and Screen Adjustment
32
33
35
Information . . . . . . . . . . . . . . . . . . . . . . . . . .40
Input Source Information Display
40
41
42
44
45
45
46
47
Cleaning the RGB panels
14
15
16
Connecting the AC Power Cord
Moving the Lens
Connecting to Video Equipment (Component)
48
49
50
52
53
54
55
55
Connecting to a Computer 17
Dimensions
22
Remote Control Operation
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in this owner’s manual is either a trademark or a registered trademark of its
respective corporation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To the Owner
Safety Precaution
Before operating this projector, read this manual thoroughly
and operate the projector properly.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
This projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintain it in better condition for a
considerable time.
– This projector produces intense light from the projection
lens. Do not stare directly into the lens as much as
possible. Eye damage could result. Be especially careful
that children do not stare directly into the beam.
Improper operation may result in not only shortening the
product life, but also malfunctions, fire hazard, or other
accidents.
– Install the projector in a proper position. If not, it may result
in a fire hazard.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section in the end of
this booklet. If the problem still persists, contact the dealer
where you purchased the projector or the service center.
– Provide appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum clearances must be maintained. If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained. Do
not cover the ventilation slot on the projector. Heat build-up
can reduce the service life of your projector, and can also
be dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SIDE and TOP
REAR
1.5' (50 cm)
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
3' (1 m)
1.5' (50 cm)
1.5' (50 cm)
– If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
CAUTION ON HANGING FROM THE CEILING
When hanging the projector from the ceiling,
clean the air intake vents, air filters, and top
of the projector periodically with a vacuum
cleaner. If you leave the projector without
cleaning for a long time, the dust will block
the operation of the cooling function, and it
may cause a breakdown or a disaster.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER’S MANUAL WITH
THIS UNIT.
NOTE: This symbol mark and recycle system are applied only
to EU countries and not applied to the countries in the
other area of the world.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR
SMOKY CONDITIONS SUCH AS IN A KITCHEN TO PREVENT
A BREAKDOWN OR A DISASTER. IF THE PROJECTOR
COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY
BECOME DETERIORATED.
Your SANYO product is designed and
manufactured with high quality
materials and components which can be
recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
CAUTION
Not for use in a computer room as defined in the Standard for
the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
Please dispose of this equipment at your local community
waste collection/recycling centre.
In the European Union there are separate collection
systems for used electrical and electronic products.
Ne peut être utilisé dans une salle d’ordinateurs telle que
définie dans la norme ANSI/NFPA 75 Standard for Protection
of Electronic Computer/Data Processing Equipment.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER
USE.
Please help us to conserve the environment we live in!
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet. This will prevent damage due to
lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b.If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d.If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e.If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance, this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer’s instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen
geleverd.
Wanneer deze leeg zijn, moet u
ze niet weggooien maar inleveren
als KCA.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
NL
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Air Circulation
Installing the Projector in Proper Position
Openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or
covered.
Install the projector properly. Improper Installation may reduce
the lamp lifetime and cause a fire hazard.
20˚
Do not tilt the projector more than 20
CAUTION
degrees from side to side.
20˚
Hot air is exhausted from the exhaust vent. When using or
installing the projector, the following precautions should be
taken.
Do not point the projector down to
project an image.
– Do not put any flammable objects or spray can near the
projector. Hot air is exhausted from the ventilation holes.
– Keep the exhaust vent at least 3’ (1 m) away from any
objects.
NO DOWNWARD
– Do not touch the peripheral part of the exhaust vent,
especially the screws and metallic part. This area will
become hot while the projector is being used.
– Do not put anything on the cabinet. Objects put on the
cabinet will not only get damaged but also cause a fire
hazard by heat.
Do not put the projector on either side
to project an image.
NO SIDEWARD
Cooling fans are provided to cool down the projector. The
fans’ running speed is changed according to the temperature
inside the projector.
Moving the Projector
When moving the projector, make sure that the automatic
slide shutter is closed and retract the adjustable feet to
prevent damage to the lens and cabinet.
When the projector is not in use for an extended period, put it
into a suitable case to protect a projector.
Care must be taken when handling the projector; do not drop,
bump, subject it to strong forces or put other things on the
cabinet.
CAUTION IN CARRYING OR TRANSPORTING
THE PROJECTOR
Exhaust Vent
(Hot air exhaust)
Air Intake Vents
– Do not drop or bump the projector, otherwise damages or
malfunctions may result.
– When carrying the projector, use a suitable carrying case.
– Do not transport the projector by using a courier or transport
service in an unsuitable transport case. This may cause
damage to the projector. To transport the projector through
a courier or transport service, consult your dealer for more
information.
– Do not put the projector in a case before the projector is
cooled enough.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communication Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: PLV-Z4
: Sanyo
: SANYO FISHER COMPANY
: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.
: (818)998-7322
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories
(UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug
will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert
the plug into the outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the
plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus
ASA
. If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required,
ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from
the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over.)
WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET.
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············ Earth
Blue ································· Neutral
Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E
or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
q Exhaust Vent
Front
Air flow
CAUTION
q
Hot air is exhausted from the exhaust vent.
Do not put heat-sensitive objects near this
side.
w Top Controls and Indicators
e Automatic Slide Shutter
r Projection Lens
t Focus Ring
y Zoom Lever
u Infrared Remote Receiver
i Vertical Lens Shift Ring (Up/Down)
o Horizontal Lens Shift Ring (Left/Right)
! Lens Shift Lock
w
e
r
t y
u
i o
!
Back
!
! Terminals and Connectors
! Power Cord Connector
! Main On/Off Switch
! Air Intake Vents/Air Filters
S-VIDEO
VIDEO
COMPONENT1
SERVICEPORT
HDMI
COMPUTER
COMPONENT2
Y
Pb/Cb Pr/Cr
!
!
!
Bottom
!
! Adjustable Feet
! Lamp Cover
! RGB Panel Cleaning Hole Cover
!
!
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Rear Terminal
q
w
e
r
S-VIDEO
COMPONENT1
SERVICEPORT
HDMI
COMPUTER
COMPONENT2
Y
Pb/Cb Pr/Cr
VIDEO
t
y
q COMPUTER
r SERVICE PORT
Connect the computer output, or RGB Scart 21-pin video
output to this connector (p.17).
This jack is used to service the projector.
t
y
HDMI
Connect the HDMI output from video equipment to this
terminal (p.17).
w S-VIDEO
Connect the S-Video output from video equipment to
this jack (p.16).
VIDEO
Connect the composite video output from video
equipment to this jack (p.16).
e COMPONENT 1 or 2
Connect the component video output to these jacks
(p.16).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Top Control
r
e
w
q
t
y
u
i
q POWER ON-OFF button
r LAMP REPLACE indicator
Turn the projector on or off (p.18, 19).
Emits a yellow light when the life of the projection lamp
draws to an end (p.46, 49).
w
POWER indicator
- Lights red while the projector is in stand-by mode.
- Lights green during operations.
- Blinks red during the cooling-off period.
t MENU button
Open or close the On-Screen Menu (p.20).
- Blinks green in the Power management mode (p.37).
y OK button
Execute the item selected or use it to access the sub-
menu items (p.20).
When the automatic slide shutter is closed during
operations, it blinks orange (p.49).
e WARNING indicator
u POINT ed7 8 buttons
Emits a red light when the projector detects an abnormal
condition. It also blinks red when the internal
temperature of the projector exceeds the operating
range (p.41, 49).
Select an item or adjust the setting values in the On-
Screen Menu, or use them to pan the image in the
Normal through mode (p.34).
i INPUT button
Select an input source (p.24).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
q POWER ON-OFF button
Remote Control
Turn the projector on or off (p.18, 19).
w NO SHOW button
Temporarily turn off the image on the screen (p.23).
e LIGHT button
Light up the remote control buttons for about 10 seconds
(p.22).
e
w
q
r LAMP CONTROL button
Select a lamp mode (p.22, 29).
t MENU button
LIGHT
LAMP CONTROL
LAMP
Open or close the On-Screen Menu (p.20).
y POINT ed7 8 buttons
NO
!
!
Select an item or adjust the setting values in the On-Screen
Menu, or use them to pan the image in the Normal through
mode (p.34).
r
t
FREEZE
RESET
SHOW
MENU
u SCREEN button
Select a screen size (p.23, 33).
i BRIGHTNESS button
!
OK
Adjust the brightness of a projected image (p.23, 28).
o LENS IRIS button
y
u
Adjust the lens iris (p.23, 29).
!
!
!
IMAGE
COLOR
SCREEN
! INPUT buttons
IMAGE ADJ.
Select an input source (p.24).
BRIGHTNESS CONTRAST
! IMAGE buttons
Select an image level (p.23, 27).
CONT.
i
o
BRIGHT
! COLOR button
LENS IRIS
IRIS
IMAGE
Adjust the color intensity of a projected image (p.23, 28).
!
PRESET
USER
! CONTRAST button
Adjust the contrast of a projected image (p.23, 28).
COMPONENT 1
C1
VIDEO
HDMI
PC
! IMAGE ADJ. button
Display the Image adj. Menu items one at a time and directly
adjust its image level (p.23, 28).
!
COMPONENT 2
C2
S-VIDEO
! OK button
INPUT
Execute the selected item or access the sub-menu items
(p.20).
! RESET button
Reset to the previous figure.
CXTS
This function is limited to when selecting the Image
Adjustment (p.28 ~ 31), Picture Adjustment (p.32) and the
Keystone function in the Setting (p.35).
! FREEZE button
Freeze the picture on the screen (p.22).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Operating Range
Point the remote control toward the projector (Infrared Remote Receiver) when pressing any buttons. Maximum operating
range for the remote control is about 16.4’ (5 m) and 60 degrees in front of the projector.
16.4’
(5 m)
60°
Remote control
Remote Control Battery Installation
Open the battery
compartment lid.
Install new batteries
into the compartment.
Replace the compartment lid.
1
2
3
Pull up the lid
and open it.
Two AA size batteries
For correct polarity (+ and
–), be sure battery terminals
are in contact with pins in
the compartment.
* When the batteries of the remote control are replaced, the remote
control code automatically returns to the initial code (Code 1) (p.38).
To insure safe operation, please observe the following precautions:
● Use two (2) AA or LR06 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
● Risk of explosion if battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Projector
This projector is designed to project on a flat projection surface having a focus range of 3.9’ (1.2 m) to 30.2’ (9.2 m) at
maximum zoom and 7.9’ (2.4 m) to 30.2’ (9.2 m) at minimum zoom. Refer to the figure and table below for the screen size
and distance between the projector and a screen.
30.2’ (9.2 m)
(Inch Diagonal)
300”
Max. Zoom
15.1’ (4.6 m)
9.8’ (3.0 m)
7.9’ (2.4 m)
150”
150”
75”
Min. Zoom
3.9’ (1.2 m)
40”
100”
50”
80”
40”
(Center)
Screen Size
(W x H) mm
16 : 9 aspect ratio
40”
80”
100”
150”
300”
886 x 498
7.9’ (2.4m)
3.9’ (1.2m)
1771 x 996
16.0’ (4.9 m)
7.9’ (2.4 m)
2214 x 1245
20.0’ (6.1 m)
9.8’ (3.0m)
3321 x 1868
30.2’ (9.2 m)
15.1’ (4.6 m)
6641 x 3736
––-––
Zoom (min)
Zoom (max)
30.2’ (9.2 m)
✔Note:
• The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.
• All measurements are approximate and may vary from the actual sizes.
Adjustable Feet
Projection angle can be adjusted up to 7.7 degrees with the
adjustable feet.
Rotate the adjustable feet and tilt the projector to the proper
height; to raise the feet, rotate the both feet clockwise.
1
To lower or to retract the adjustable feet, rotate the both feet
counterclockwise.
Keystone distortion of the projected image can be corrected
by menu operation (p.35).
2
Adjustable Feet
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-120V or 200-
240V AC and it automatically selects a correct input voltage. It is
designed to work with the single-phase power systems having a
grounded neutral conductor. To reduce the risk of electrical shock,
do not plug into any other type of power system.
S-VIDEO
VIDEO
COMPON
COMPON
HDMI
COMPUTER
If you are not sure of the type of power being supplied, consult
your authorized dealer or service station.
Y
Pb/Cb Pr/Cr
Connect the projector with all peripheral equipment before turning
on the projector. (See pages 16 ~ 17 for connection.)
CAUTION
For safety, unplug the AC power cord when the projector is not
in use.
When the projector is connected to an outlet with the AC power
cord and the Main On/Off switch is on, it is in stand-by mode
and consumes a little electric power. Turn the Main On/Off
switch off when the projector is not in use.
Connect the AC power cord (supplied) to the
projector.
The AC outlet must be near this equipment and must
be easily accessible.
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and a proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC outlet side
For the U.S.A. and Canada For Continental Europe
For the U.K.
Ground
To power cord
connector on your
projector.
To the AC outlet.
(120 V AC)
To the AC outlet.
(200 - 240 V AC)
To the AC outlet.
(200 - 240 V AC)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Moving the Lens
The projection lens can be moved up and down or left and right manually with the Lens Shift Rings, enabling you to adjust
the position of a projected image. After adjusting the position, lock the lens with the Lens Shift Lock.
Horizontal Lens Shift Ring
(Left/Right)
Lens Shift Lock
Move the projection lens to the left or right with the Horizontal
Lens Shift Ring.
Move the projection lens up or down with the Vertical Lens Shift
Ring.
Vertical Lens Shift Ring
(Up/Down)
Horizontal Lens Shift (Left/Right)
1/2W
1/2W
W
W
leftmost
rightmost
Vertical Lens Shift (Up/Down)
V
V
V
V
uppermost
downmost
✔Note:
• The best image is generally obtained at the center axis of the lens shift.
• When moving the projection lens to the left or right to its maximum limit, the vertical lens shift function does not work to its maximum limit; when moving the
projection lens up or down to its maximum limit, the horizontal lens shift function does not work to its maximum limit.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
This projector can be connected up to six equipment at one time. See the figures below for the connections.
Connecting to Video Equipment (Video, S-Video)
Video, S-video
Video Equipment
Use the supplied video cable or a S-video cable (commercially
available).
Composite
Video Output
S-VIDEO
Output
Video Cable
(RCA x 1)
S-video
Cable
VIDEO
S-VIDEO
S-VIDEO
VIDEO
COMPONENT1
COMPONENT2
SERVICEPORT
HDMI
COMPUTER
Y
Pb/Cb Pr/Cr
Connecting to Video Equipment (Component)
Component
Video Equipment
Use a component cable (optional).
Component Video Output
(Y, Pb/Cb, Pr/Cr)
Component
Cable
(RCA x 3)
COMPONENT
S-VIDEO
COMPONENT1
✔Note:
SERVICEPORT
HDMI
COMPUTER
COMPONENT2
• See page 55 for ordering optional cables.
Y
Pb/Cb Pr/Cr
VIDEO
Note:
When connecting cables, the power cords of both the projector and external
equipment should be disconnected from the AC outlet.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment (HDMI, RGB Scart)
HDMI
RGB Scart
Use a HDMI cable (optional) for HDMI output.
Use a Scart-VGA cable (optional).
Video Equipment
Video Equipment
HDMI Video
Output
RGB Scart
21-pin Output
Scart-VGA
Cable
HDMI
Cable
HDMI
COMPUTER
S-VIDEO
S-VIDEO
COMPONENT1
COMPONENT1
COMPONENT2
SERVICEPORT
SERVICEPORT
HDMI
COMPUTER
HDMI
COMPUTER
COMPONENT2
Y
Pb/Cb Pr/Cr
VIDEO
Y
Pb/Cb Pr/Cr
VIDEO
Connecting to a Computer
Computer (Analog)
IBM-compatible or Macintosh computer
Use a VGA cable (commercially available) or a DVI-VGA cable
(commercially available).
Monitor Out
DVI-VGA
Cable
VGA
Cable
COMPUTER
S-VIDEO
COMPONENT1
✔Note:
SERVICEPORT
HDMI
COMPUTER
COMPONENT2
• See page 55 for ordering optional cables.
Y
Pb/Cb Pr/Cr
VIDEO
Note:
When connecting cables, the power cords of both the projector and external
equipment should be disconnected from the AC outlet.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
Complete peripheral connections (with a computer, VCR,
etc.) before turning on the projector.
POWER
ON-OFF
button
1
2
POWER indicator
Connect the projector’s AC power cord into an AC outlet and
turn the Main On/Off switch on. The POWER indicator lights
red.
Press the POWER ON-OFF button on the top control or on
the remote control. The POWER indicator turns green and
the cooling fans start to operate. The automatic slide shutter
opens, and then a preparation display appears on the screen
and the countdown will start.
3
NO
SHOW
FREEZE
Top Control
Remote Control
After the countdown, the input source that was selected the
last time will appear on the screen.
4
Main On/Off switch
✔Note:
• If the automatic slide shutter is half-open, projector will not be turned on and the
POWER indicator will blink orange. In this case, press the POWER ON-OFF button
again.
OFF
ON
• When “Countdown off” or “Off” is selected in the Display function, the countdown
will not be shown on the screen (p.36).
Selected Input Source
• During the countdown period, all operations are invalid.
Automatic Slide Shutter
Use this tab when handling manually.
Do not touch the slide shutter while it is
moving, as this could cause injury or the
projector to malfunction.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning Off the Projector
Press the POWER ON-OFF button on the top control or on
the remote control. “Power off?” appears on the screen.
Press the POWER ON-OFF button again to turn off the
projector.
1
(When the Power off confirmation function is “Off”, the
projector will be turned off without confirmation. (See
“Power off confirmation” in the Setting Menu on page 37.)
The automatic slide shutter closes and the POWER indicator
starts to blink red. The blinking continues for about 60
seconds while the cooling fans are operating.
“Power off?” disappears after 4 seconds.
When the projector has cooled down enough to be turned on
again, the POWER indicator will become red. Then you can
turn the Main On/Off switch off and unplug the AC power
cord.
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
THE PROJECTOR ON, WAIT AT LEAST FIVE (5)
MINUTES BEFORE TURNING IT OFF.
DO NOT UNPLUG THE AC POWER CORD WHILE THE
COOLING FANS ARE RUNNING OR BEFORE THE
POWER INDICATOR STOPS BLINKING. OTHERWISE IT
WILL RESULT IN SHORTENING THE LAMP LIFE.
✔Note:
• If the automatic slide shutter is closed during operation, the projector is automatically
turned off for safety. Be sure to turn off the projector by pressing the POWER ON-
OFF button on the top control or on the remote control after use.
• While the POWER indicator is blinking, the lamp is being cooled down and the
projector can not be turned on. Wait until the POWER indicator becomes red to be
turned on again.
• Do not operate the projector continuously without rest. Continuous use may result in
shortening the lamp life. Turn off the projector and rest it for about an hour in every
24 hours.
• The running speed of cooling fans is changed according to the temperature inside
the projector.
• If the WARNING indicator blinks or emits a red light, see “Warning Indicator” on
page 41.
• Do not put the projector in a case before it is cooled enough.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen Menu. The
menus have a hierarchical structure, with a main menu that is
divided into sub-menus, which are further divided into other sub-
menus. Refer to the following pages regarding each adjustment
and setting procedure.
Top Control
POINT buttons
(Arrows-marked)
Press the MENU button on the top control or on the remote
1
control to display the On-Screen Menu.
OK button
Use the Point ed buttons to highlight or select a main menu
item. Press the Point 8 or OK buttons to access the sub-
menu items. (The selected item is highlighted in ORANGE.)
MENU button
2
Remote Control
Use the Point ed buttons to select the desired sub-menu
item and press the Point 8 or OK buttons to access the
NO
3
FREEZE
LAMP
MENU button
SHOW
selected item.
MENU
RESET
POINT buttons
(Arrows-marked)
Use the Point 7 8 or OK buttons to adjust the setting or
switch between each mode and press the OK or Point 8
buttons to activate it and return to the sub-menu.
4
OK
OK button
Return to the main menu by pressing the Point 7 button. To
exit the On-Screen Menu, press the MENU button again.
IMAGE
SCREEN
5
IMAGE ADJ.
On-Screen Menu (Main Menu)
Point
Right or OK
buttons
The selected item is
highlighted in ORANGE.
On-Screen Menu (Sub-Menu)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu and its Functions
For the detailed menu contents, see the Menu Tree on pages 50 ~ 51.
Main Menu
Sub-Menu
q
w
e
r
t
y
u
i
q Image
Select an image level from among Creative cinema, Pure cinema, Natural, Living, Dynamic, Powerful,
Vivid, User Image 1 ~ 4 (p.27).
w
Image adj.
Adjust Brightness, Contrast, Color, Tint, Color temp., White balance (R/G/B), Sharpness, Lamp control,
Gamma, Progressive, Lens iris, Advanced menu, Reset, Store (p.28 ~ 31).
e Picture adj.
Select Overscan, Horizontal, Vertical, Auto adj., Fine sync and Total dots to adjust the parameters to
match with the input signal format (p.32).
r Screen
Set the screen size from among Full, Full through, Zoom, Caption in, Normal, Normal through, Natural
wide 1, Natural wide 2 (p.33 ~ 34).
t Input
Select an input source from among Video, S-video, Component 1, Component 2, HDMI and Computer.
For Video and S-video input, select a video system from AUTO, PAL, SECAM, NTSC, NTSC4.43, PAL-M,
PAL-N (p.24 ~ 26).
y Setting
Change various settings; Language, Advanced menu, Menu position, Keystone, Mounting, Rear, HDMI
setup, Blue back, Display, Logo, Power off confirmation, Capture, Power management, Remote control,
Shutter demo, Cleaning, Panel adjustment, Lamp counter reset, Factory default (p.35 ~ 39).
u Information
Display Signal, H-sync freq., V-sync freq. of the projected screen and the Lamp Time (p.40).
i Guide
The key operation is displayed.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Zoom and Focus Adjustment
Rotate the Zoom Lever to zoom in and out.
Rotate the Focus Ring to focus the image.
Zoom Lever
Focus Ring
Remote Control Operation
For some frequently used operations, using the remote control is advisable. Just pressing one of the buttons enables you to
make the operation, and no need for calling up the On-Screen Menu.
LIGHT button
Remote Control
Press the LIGHT button to light up the remote control buttons. The
lights will be automatically turned off when no buttons on the
remote control are pressed for 10 seconds.
LIGHT
button
LIGHT
LAMP CONTROL
NO
FREEZE
button
LAMP
CONTROL
button
FREEZE
RESET
LAMP
SHOW
FREEZE button
MENU
Press the FREEZE button to freeze the picture on the screen. To
cancel the Freeze function, press the FREEZE button again or
press any other button.
OK
LAMP CONTROL button
IMAGE
SCREEN
Press the LAMP CONTROL button to select a lamp mode for
changing the brightness of the screen.
IMAGE ADJ.
Normal . . . . . Normal brightness.
✔Note:
• See the next page for other buttons.
Auto 1 . . . . . The brightness according to the input signal.
Auto 2 . . . . . Less bright and lower-sound than Auto 1.
Eco . . . . . . . Lower brightness reduces the lamp power
consumption.
The lamp mode is automatically switched to the Eco mode under
no signal input.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
SCREEN button
Remote Control
LAMP CONTROL
Press the SCREEN button to select the desired screen size. See
page 33 for details.
NO SHOW
button
NO
FREEZE
RESET
LAMP
SHOW
MENU
RESET
button
NO SHOW button
Press the NO SHOW button to black out the image. To restore to
normal, press the NO SHOW button again or press any other
button.
OK
IMAGE
ADJ.
button
SCREEN
button
IMAGE
COLOR
SCREEN
IMAGE ADJ.
CONTRAST
button
RESET button
BRIGHTNESS CONTRAST
BRIGHTNESS
button
Press the RESET button to reset the adjusted data. All
adjustments return to their previous figures. When selecting a
main menu item, its entire sub-menu items will be reset. When
selecting a sub-menu item, only the selected item will be reset.
This function is limited to when selecting the Image Level
Adjustment (p.28 ~ 31), Picture Adjustment (p.32) and the
Keystone function in the Setting (p.35).
CONT.
BRIGHT
COLOR
button
LENS IRIS
IRIS
IMAGE
PRESET
USER
LENS IRIS
button
IMAGE
buttons
✔Note:
• See the previous page for other buttons.
IMAGE ADJ. button
Press the IMAGE ADJ. button to display the Image adj. Menu
items one at a time and directly adjust the selected item. See
page 28 for details.
BRIGHTNESS button
To adjust the brightness, press the BRIGHTNESS button to display
the adjustment bar and use the Point 7 8 buttons to adjust the
brightness. Press the MENU button after adjusting. See page 28
for details.
“No Show” disappears after 4 seconds.
CONTRAST button
To adjust the contrast, press the CONTRAST button to display the
adjustment bar and use the Point 7 8 buttons to adjust the
contrast. Press the MENU button after adjusting. See page 28 for
details.
COLOR button
To adjust the color, press the COLOR button to display the
adjustment bar and use the Point 7 8 buttons to adjust the color.
Press the MENU button after adjusting. See page 28 for details.
LENS IRIS button
To adjust the lens iris, press the LENS IRIS button to display the
adjustment bar and use the Point 7 8 buttons to adjust the lens
iris. Press the MENU button after adjusting. See page 29 for
details.
IMAGE buttons
Press the IMAGE buttons to select the desired image level of the
screen. See page 27 for details.
✔Note:
• If you press the OK button after adjusting each Image adj. Menu item or the
brightness, contrast, color and lens iris, it enters the On-Screen Menu.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Input
Input Source and System Selection
Choose an input source by pressing the INPUT button on the top
control or the INPUT buttons on the remote control.
INPUT button
Video
Top Control
S-video
Component 1
Component 2
HDMI
✔Note:
• Before selecting an input source with these buttons, each input must be set on a
proper signal form via menu operation on pages 25 and 26.
INPUT button
Computer
INPUT buttons
Remote Control
COMPONENT 1
Press the VIDEO, S-VIDEO, C1, C2, HDMI or PC buttons on the
remote control according to the input source.
VIDEO
HDMI
PC
C1
COMPONENT 2
C2
S-VIDEO
VIDEO
S-VIDEO
C1/C2
HDMI
PC
When the video input signal is connected to the
VIDEO jack, select VIDEO.
INPUT
When the video input signal is connected to the S-
VIDEO jack, select S-VIDEO.
CXTS
When the video input signal is connected to the Y-
Pb/Cb-Pr/Cr jacks, select C1 or C2.
INPUT buttons: VIDEO/S-VIDEO/C1/C2/HDMI/PC
When the video input signal is connected to the
HDMI terminal, select HDMI.
When the computer input signal is connected to the
COMPUTER connector, select PC.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Input
Input Menu
Menu Operation
Select the Input Menu with the Point ed buttons and press
the Point 8 or OK buttons to access the sub-menu items.
1
2
Use the the Point ed buttons to select an input source and
press the OK or Point 8 buttons. The selected item will be
check marked.
When selecting Video or S-video, press the Point 8 button to
display the System Menu.
3
4
5
6
Use the Point ed buttons to select the desired system and
press the OK or Point 8 buttons.
The currently set item
is check marked.
When selecting Computer, press the Point 8 button to
display the Source Select Menu.
Use the Point ed buttons to select the desired source and
press the OK or Point 8 buttons.
Video or S-Video
When the video input signal is connected to the VIDEO or S-
VIDEO jacks, select Video or S-video respectively.
Auto
Press the Point 8 button
to display the System
Menu.
Video
Input
The projector automatically detects the incoming video system
and adjusts itself to optimize its performance.
When the video system is PAL-M or PAL-N, select the system
manually.
System Menu (Video/S-Video)
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce a proper video image, select a
specific broadcast signal format from among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Use the Point ed buttons
to select the desired
system and press the OK
or Point 8 buttons.
Component 1 or 2
When the video input signal is connected to the Y-Pb/Cb-Pr/Cr
jacks, select Component 1 or 2.
The projector automatically detects the incoming video signal and
adjusts itself to optimize its performance.
Quit
Exit this menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Input
HDMI
When the video input signal is connected to the HDMI terminal,
select HDMI.
The projector automatically detects the incoming video signal and
adjusts itself to optimize its performance.
If the output signal of video equipment and the input signal of the
projector do not match, you might not get an image with the best
quality.
If the black part of the picture appears unclear (too dark or too
light), try the input signal with “HDMI setup” in the Setting Menu
on page 36.
Computer
When the input signal is connected to the COMPUTER connector,
select Computer.
When the input source is analog coming from a
computer connected to the COMPUTER
connector, select RGB (Analog).
RGB (Analog)
When the input terminal is Scart with a DVD
player connected to the COMPUTER connector,
select RGB (Scart).
RGB (Scart)
This projector automatically tunes to various types of computers
based on VGA, SVGA, XGA or SXGA with its Multi-scan system
and the Auto adj. function (p.32). If Computer is selected as a
signal source, this projector automatically detects the signal
format and tunes to project a proper image without any additional
setting. (The signal formats provided in this projector is shown on
page 52.)
Press the Point 8 button
to display the Source
Select Menu.
Computer
Input
Source Select Menu
Use the Point ed buttons
to select the desired
source and press the OK
or Point 8 buttons.
Quit
Exit this menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Image
Image Level Selection
Image level selection can be made for each input source.
Remote Control
Direct Operation
IMAGE ADJ.
BRIGHTNESS CONTRAST
Select the desired image level among Creative cinema, Pure
cinema, Natural, Living, Dynamic, Powerful, Vivid, User Image 1 ~
4 by pressing the IMAGE buttons (PRESET or USER) on the
remote control.
CONT.
COLOR
USER
BRIGHT
LENS IRIS
IRIS
IMAGE
IMAGE buttons
PRESET
COMPONENT 1
C1
VIDEO
HDMI
Use the PRESET button to select Creative cinema, Pure cinema,
Natural, Living, Dynamic, Powerful and Vivid. Use the USER
button to select User image 1 ~ 4
.
PRESET button
Creative cinema ➜ Pure cinema ➜ Natural ➜
Living ➜ Dynamic ➜ Powerful ➜ Vivid ➜
Menu Operation
• • • • •
Select the Image Menu with the Point ed buttons and
press the Point 8 or OK buttons to access the sub-menu
items.
USER button
1
2
User image 1 ➜ User image 2 ➜ User image 3 ➜
User image 4 ➜
• • • • •
Use the Point ed buttons to select the desired image level
and press the OK or Point 8 buttons. The selected item will
be check marked.
Image Menu
Creative cinema
Suitable for viewing contrasty 3D images in a dark room.
Pure cinema
Suitable for viewing images with quiet tones of color with less
gradation in a dark room.
Natural
Suitable for viewing faithfully reproduced images without any
control by the projector in a dark room.
The selected image level.
Living
Suitable for viewing video sources such as sports or dramas from
TV with clear and contrasty images in a bright room.
Dynamic
Suitable for viewing contrasty images in a bright room.
Powerful
Suitable for viewing with a big screen in a bright room.
Press the Point d button
to move on to the next
items.
Vivid
Suitable for viewing contrasty images to a maximum extent.
User image 1 ~ 4
User preset images in the Image adj. Menu (p.28 ~ 31).
✔Note:
• The Image Menu cannot be operated without an input signal.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
Image Level Adjustment
Image level can be adjusted for each input source and the adjustment is kept until the projector is turned off.
Remote Control
Direct Operation
MENU
RESET
Press the IMAGE ADJ. button on the remote control to display the
Image adj. Menu items one at a time and directly adjust the
selected item.
OK
Use the Point ed buttons to select the desired item and the Point
7 8 buttons to adjust the settings. Press the MENU button after
adjusting.
If you press the OK button after adjusting each item, it enters the
On-Screen Menu.
IMAGE
COLOR
SCREEN
IMAGE ADJ. button
IMAGE ADJ.
BRIGHTNESS CONTRAST
CONT.
BRIGHT
Brightness ➜ Contrast ➜ Color ➜ Tint ➜ Color
temp. ➜ Red ➜ Green ➜ Blue ➜ Sharpness ➜
Lamp control ➜ Gamma ➜ Progressive ➜ Lens
iris ➜ Lamp iris ➜ Auto black stretch➜ Contrast
enhancement ➜ Transient improvement ➜ Gain
Menu Operation
Select the Image adj. Menu with the Point ed buttons and
press the Point 8 or OK buttons to access the sub-menu
items.
1
• • • • •
R/G/B ➜ Offset R/G/B ➜ Gamma R/G/B ➜
Use the Point ed buttons to select the desired item and
press the Point 8 or OK buttons to access the selected item.
The adjustment bar will be displayed.
2
Image adj. Menu
Use the Point 7 8 buttons to adjust the setting values and
press the OK button.
3
Brightness
Press the Point 7 button to decrease the brightness; press the
Point 8 button to increase the brightness. (From -31 to +31.)
Contrast
Press the Point 7 button to decrease the contrast; press the Point
8 button to increase the contrast. (From -31 to +31.)
Color
The selected item.
Press the Point 7 button to decrease the intensity of the color;
press the Point 8 button to increase the intensity of the color.
(From -31 to +31.)
Tint
Use the Point 7 8 buttons to adjust the tint value to obtain a
proper color balance. (From -31 to +31.)
Color temp.
Use the Point 7 8 buttons to select the desired Color temp. level.
(High, Mid, Low1, Low2, or Low3.)
Press the Point 8 or OK
buttons to access the
selected item. The adjust-
ment bar will be displayed.
Use the Point 7 8 buttons
to adjust the setting values
and press the OK button.
If you press the Point
button, the next item can
be selected.
d
✔Note:
• Tint cannot be selected when the video system is PAL, SECAM, PAL-M, or PAL-N
except for 575i.
• The Image adj. Menu cannot be operated without an input signal.
Go on to the next page...
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
White balance (Red)
Press the Point 7 button to lighten red tone; press the Point 8
button to deepen red tone. (From -31 to +31.)
White balance (Green)
Press the Point 7 button to lighten green tone; press the Point 8
button to deepen green tone. (From -31 to +31.)
White balance (Blue)
Press the Point 7 button to lighten blue tone; press the Point 8
button to deepen blue tone. (From -31 to +31.)
Sharpness
Press the Point 7 button to decrease the sharpness of the image;
press the Point 8 button to increase the sharpness of the image.
(From -7 to +7.)
Lamp control
This function allows you to change the brightness of the screen.
Use the Point 7 8 buttons to select the desired lamp mode. You
can also select the lamp mode by pressing the LAMP CONTROL
button on the remote control.
Normal . . . . . Normal brightness.
Auto 1 . . . . . The brightness according to the input signal.
Auto 2 . . . . . Less bright and lower-sound than Auto 1.
Eco . . . . . . . Lower brightness reduces the lamp lower
consumption.
Press the Point 8 or OK
buttons to display the
Advanced menu.
The lamp mode is automatically switched to the Eco mode under
no signal input.
Gamma
Use the Point 7 8 buttons to adjust the gamma value to obtain a
better balance of contrast. (From -7 to +7.)
Progressive
An interlaced video signal can be displayed in progressive. Use the
Point 7 8 buttons to select the desired mode.
Off . . . . . Disabled.
L1 . . . . . Select “L1” for moving pictures.
L2 . . . . . Select “L2” for still pictures.
Film . . . . Select “Film” for watching a film. With this function,
the projector reproduce pictures faithful to the original
film quality; it operates on 3-2 and 2-2 pulldown video
sources.
Press the Point d button
to move on to the next
items.
Lens iris
Use the Point 7 8 buttons to adjust the lens iris. It can be stopped
down from zero. (From 0 to -63.)
Go on to the next page...
✔Note:
• If any of the White balance (Red, Green or Blue) is adjusted, the Color temp. level
will change to “User”.
• Progressive cannot be selected with the computer input and when the video signal
format is 480p, 575p, or 720p.
• The Film mode in the Progressive function cannot be selected when the video signal
format is 1080i. If you select the Film mode when the video signal format is 480i
and then input 1080i signal, it will switch to the L1 mode.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
Advanced menu
This function can be selected only when Advanced menu in the
Setting Menu (p.35) is “On”. You can adjust the following items
through this function.
Lamp iris . . . . . . . . . . . . . Select Auto, Open or Close for the
Lamp iris.
Auto black stretch . . . . . Enhance the black color in a bright
image. Select Off/ L1/L2/L3.
Contrast enhancement . . Adjust the contrast of color in a bright
image. Select Off/ L1/L2/L3.
Transient improvement . . . . Adjust the sharpness of picture
outline. Select Off/ L1/L2/L3.
Color management . . . . . Adjust color level, color phase and
gamma of the selected spot of a
projected image. Exchange the
original color with the adjusted one.
The projector can store up to eight (8)
color management data. For details,
see “COLOR MANAGEMENT”
below.
Press the Point 8 or OK
buttons to access the
selected item. The adjust-
ment bar will be displayed.
Gain R/G/B . . . . . . . . . . . Adjust red, green and blue to get the
desired contrast of color.
(From -15 to +15.)
Offset R/G/B . . . . . . . . . . Adjust red, green and blue to get the
desired brightness of color.
(From -15 to +15.)
Gamma R/G/B . . . . . . . . Adjust red, green and blue to get the
desired neutral color.
Use the Point 7 8 buttons
to adjust the setting values
and press the OK button.
If you press the Point
d
button, the next item can
be selected.
(From -5 to +5.)
COLOR MANAGEMENT LIST
COLOR MANAGEMENT
COLOR MANAGEMENT LIST
Select Color management in the Advanced menu and then
press the OK or Point
8
buttons. The COLOR
MANAGEMENT LIST will appear. You can store up to eight
(8) color management data in the list.
Press the OK button when selecting the following items.
ALL DEL . . . . . Delete all the data in the list.
Press the OK button and the confirmation
box will appear. Select [Yes] and press the
OK or Point 8 buttons.
COLOR M. . . . Go to COLOR SELECTION on the next
page.
EXIT . . . . . . . . Exit the Color management mode and
return to the Advanced menu. To store the
adjusted data, see “Store” in the next
page.
Clear the check mark if you
do not want to apply this
adjusted color data to a
projected image.
Select the DEL box if
you want to delete the
adjusted data. The
confirmation box will
appear.
Press the MENU button when you want to return to the
Advanced menu.
Select [Yes] to delete
the adjusted color data.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Adjustment
COLOR SELECTION
COLOR SELECTION
Press the OK button when selecting COLOR M. in the Color
management list. The Color management list disappears
and the Color management pointer will appear.
Color management pointer
Use the Point ed 7 8 buttons to move
the pointer to a spot where you want to
adjust the color and then press the OK
button. The COLOR SELECTION
window will appear.
Use the Point ed 7 8 buttons to move the pointer to a spot
where you want to adjust the color and then press the OK
button. The image being projected freezes and the COLOR
SELECTION window will appear. (Certain colors may not be
adjusted and in such cases, an exclamation mark will be
displayed.)
Select COLOR LEVEL, COLOR PHASE or GAMMA with the
Point ed buttons and use the Point 7 8 buttons to adjust
them. While adjusting, the changes are reflected in the
projected image accordingly. If you press the MENU button
while operating the color selection, the Color management
pointer will be reset. After adjusting, press the OK button to
go to the Color management list.
COLOR MANAGEMENT LIST (continued)
In the COLOR MANAGEMENT LIST, the adjusted color data
are check marked reflecting the changes in the projected
image. (See the previous page.)
After adjusting Color level,
Color phase and Gamma,
press the OK button.
You can also decide whether or not to apply the adjusted
color data in the list to a projected image. Clear the check
mark if you do not want to apply the adjusted color data;
select the check mark and then press the OK button. The
check mark will disappear.
Go to the Color management list (see the previous
page).
To store the adjusted data,
exit the Color management
mode and move on to
“Store” in the Image adj.
Menu.
If you want to readjust the color, select a color data box in
the list and press the OK button. The COLOR SELECTION
window will appear and you can readjust the color. See
above for color selection.
If you want to delete a particular color data in the list, select
the DEL box of the color data and then press the OK button.
The confirmation box will appear. Select [Yes] and then
press the OK or Point 8 buttons.
Reset
To reset the adjusted data, select Reset and press the Point 8 or
OK buttons. The confirmation box will appear. Select [Yes] and
then press the OK or Point 8 buttons. All adjustments return to
their previous figures. You can also reset the adjusted data with
the RESET button on the remote control.
Press the Point 8 or OK
buttons at this icon to
store the adjusted data.
The Image Level Menu will
appear.
Store
To store the adjusted data, select Store and press the Point 8 or
OK buttons. The Image Level Menu will appear. Choose one of
the four (4) image levels with the Point ed buttons and press the
OK or Point 8 buttons. The confirmation box will appear. Select
[Yes] and then press the OK or Point 8 buttons. To exit the Image
Level Menu, press the OK or Point 8 buttons at the Quit icon.
Choose one of the four (4)
image levels with the Point
ed buttons and press the
OK or Point 8 buttons. The
confirmation box will appear.
Select [Yes] and then press
the OK or Point 8 buttons.
The stored data can be called up by selecting “User image 1 ~ 4”
in the Image Level Selection on page 27.
✔Note:
• If you turn off the POWER without storing adjusted settings, all the adjusted settings
will be reset.
Quit
• When resetting, the adjusted data in Advanced menu will be reset whether or not
Advanced menu in the Setting Menu is “On”. See on page 35.
Press the OK or Point
8
buttons at this icon to close
the dialog box.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment
Picture Position and Screen Adjustment
Some input source employ special signal formats which may not be tuned by the auto-tuning system of this projector.
Picture Adjustment enables you to precisely adjust several parameters manually to match those signal formats. The
parameters manually adjusted will be stored for every input.
Select the Picture adj. Menu with the Point ed buttons and
press the Point 8 or OK buttons to access the sub-menu
items.
1
Picture adj. Menu
Use the Point ed buttons to select the desired item and
press the Point 8 or OK buttons to access the selected item.
The adjustment bar will be displayed.
2
Use the Point 7 8 buttons to adjust the setting values and
press the OK button.
3
Overscan
Use the Point 7 8 buttons to adjust the overscan area. It works
only to decrease the overscanned portion of the screen.
(From 0 to +10.)
The selected item.
Horizontal
Use the Point 7 8 buttons to adjust the horizontal picture position.
(From -100 to +100.)
Vertical
Use the Point 7 8 buttons to adjust the vertical picture position.
(From -100 to +100.)
Auto adj.
Press the Point 8 or OK
buttons to access the
selected item. The adjust-
ment bar will be displayed.
When the input signal is from a computer, select Auto adj. Press
the Point 8 or OK buttons and it automatically adjust Fine sync.
Total dots, Horizontal and Vertical positions to conform to your
computer.
Fine sync
Use the Point 7 8 buttons
to adjust the the setting
values and press the OK
button to return to the sub-
menu.
Eliminate a flicker from the image displayed. Use the Point 7 8
buttons to adjust the value. (From 0 to +31.)
Total dots
Adjusts the number of total dots in one horizontal period. Use the
Point 7 8 buttons to adjust the number to match your PC image.
(From -100 to +100.)
If you press the Point
d
button, the next item can
be selected.
✔Note:
• Overscan can be selected with the video input only.
• The adjusting range for the Horizontal and Vertical positions and Total dots differs
depending on the input signal. When the video signal format is 480i or 575i, the
adjusting range for the Horizontal position will be from -8 to +8.
• The Auto adj. function cannot be operated with the video input, some incompatible
computer input and digital signals.
• Fine sync and Total dots cannot be operated when the video signal format is 480i or
575i and with some incompatible computer input and digital signals.
• The Picture adj. Menu cannot be operated without an input signal.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen
Screen Size Adjustment
This projector has the picture screen resize function which enables you to customize the image size.
Remote Control
Direct Operation
OK
Select a screen size among Full, Full through, Zoom, Caption in,
Normal, Normal through, Natural wide 1 and Natural wide 2 by
pressing the SCREEN button on the remote control.
SCREEN button
IMAGE
COLOR
SCREEN
IMAGE ADJ.
BRIGHTNESS CONTRAST
CONT.
BRIGHT
Full ➜ Full through ➜ Zoom ➜ Caption in ➜
Normal ➜ Normal through ➜ Natural wide 1 ➜
• • • • •
Natural wide 2 ➜
Screen Menu
Menu Operation
Select the Screen Menu with the Point ed buttons and
press the Point 8 or OK buttons to access the sub-menu
items.
1
Use the Point ed buttons to select the desired screen size
and press the OK or Point 8 buttons. The selected item will
be check marked.
2
Full
Fit the image to the screen by expanding the width of the image
uniformly. This function can be used to project a squeezed video
signal at the wide video aspect ratio of 16 : 9.
The selected screen size.
To get a better quality, select the 16 : 9 output mode as well if it is
available on your video equipment (such as DVD players).
Full through
Fit the image to the screen by expanding the width of the image
and project it in the center of the screen at the wide screen ratio
of 16 : 9. (You can enjoy a high-quality image even though the
projected image is smaller.)
Zoom
Full
Fit the image to the screen size (16 : 9 aspect ratio) by expanding
the width and height of the image uniformly.
With the input signals other than 1080i or 720p, this function is
used to project a letterboxed picture (the 4 : 3 aspect ratio picture
with a black bar at the top and bottom) at the wide video aspect
ratio of 16 : 9.
When the input signal is 1080i or 720p, a letterboxed picture in a
16 : 9 screen can be projected by expanding at the wide video
aspect ratio of 16 : 9.
Full through
You can also adjust the display range with the vertical adj. function
in the Zoom mode. See “Vertical adj.” on the next page for details.
Zoom
When the input signal is 1080i or 720p.
✔Note:
• The Screen Menu cannot be operated without an input signal.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen
Caption in
Caption in
Fit the image to the screen size (16 : 9 aspect ratio) by
compressing the image including the captions.
Racing is stimulating!
Let's enjoy it!
Racing is stimulating!
Let's enjoy it!
With the input signals other than 1080i or 720p, this function is
used to project a 4 : 3 picture with captions at the wide video
aspect ratio of 16 : 9.
When the input signal is 1080i or 720p.
When the input signal is 1080i or 720p, a picture with captions in a
16 : 9 screen can be projected by expanding at the wide video
aspect ratio of 16 : 9.
Racing is stimulating!
Let's enjoy it!
Racing is stimulating!
Let's enjoy it!
If a part of the captions is out of the screen, adjust the display
range with the Vertical adj. function. See “Vertical adj.” below for
details.
Normal
Normal
Fit the image to the center of the screen at the normal video
aspect ratio of 4 : 3.
Normal
through
Normal through
Fit the image to the center of the screen without modification.
(You can enjoy a high-quality image even though the projected
image is smaller.)
When the original image size is larger than the screen size (1280 x
720), adjust the display range with the Panning function.
Natural
wide 1
Natural wide 1
Modify a 4 : 3 aspect ratio image to fit the screen size (16 : 9
aspect ratio) by stretching the image to make it look natural.
Natural
wide 2
Natural wide 2
When the signal is 16 : 9, modify a 4 : 3 aspect ratio image to fit
the screen size (16 : 9 aspect ratio) by stretching the image to
make it look natural.
Vertical adj.
When it is in the Zoom or Caption in mode, press the
Point ed buttons to display the Vertical adj. dialog box.
Use the Point ed buttons to adjust the vertical
position. The adjusting range differs depending on the
input signal.
The adjusted value is only effective in the Zoom and
Caption in mode.
The Vertical adj. dialog box cannot be displayed when
the On-Screen Menu is on.
✔Note:
Panning
• When the video signal format is 720p, 1080i, or HDTV, the Screen Menu cannot be
selected except for Full, Zoom, Caption in and Natural wide 2.
• When Normal is selected with a computer input, the image is projected at the
inputted resolution.
When it is in the Normal through mode, press the Point
ed buttons to display the panning dialog box. Use the
Point ed7 8 buttons to pan the image. Only the
displayed direction of arrows are active.
The panning dialog box cannot be displayed when the
On-Screen Menu is on.
• This projector cannot display any resolution higher than 1920 x 1080. If your
computer’s resolution is higher than that, lower the resolution before connecting to
the projector.
• The image data other than the 1280 x 720 resolution is modified to fit the screen
size in initial mode.
• The Vertical adj. function is operated only when Zoom or Caption in is selected.
• The panning function for Normal through is operated only with a computer input.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Setting
The Setting Menu allows you to set up other various functions described below.
Setting Menu
Select the Setting Menu with the Point ed buttons and
press the Point 8 or OK buttons to access the sub-menu
items.
1
Use the Point ed buttons to select the desired item and
press the Point 8 or OK buttons to access the selected item.
2
3
Use the Point ed or OK buttons to adjust the setting.
Language
The language used in the On-Screen Menu is available in English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Finnish, Polish, Hungarian, Romanian, Russian, Chinese, Korean,
or Japanese.
Language
Advanced menu
When this function is “On”, the Advanced menu in the Image
Level Adjustment can be selected. Press the Point 8 or OK
buttons to switch On/Off. See “Image Level Adjustment” on page
30 for details.
Press the Point 8 or OK
buttons to display the
Language Menu.
Menu position
This function is used to change the position of the On-Screen
Menu. Select Menu position and press the Point 8 or OK buttons.
The Menu position screen will appear. Select the desired position
with the Point ed7 8 buttons and press the OK button.
Choose a language and
press the OK or Point
8
buttons. The pointer will
move to this icon. Press
the OK or Point 8 buttons
again to activate it.
Keystone
When the image is distorted vertically, select Keystone and press
the Point 8 or OK buttons. The On-Screen Menu disappears and
the Keystone dialog box will appear. Correct keystone distortion by
pressing the Point ed buttons.
Menu position
Reduce the upper width with
the Point e button.
Reduce the lower width with
the Point d button.
Select Menu position and
press the Point 8 or OK
buttons. The Menu position
screen will appear.
• The arrows are white when there is no correction.
• The arrows disappear at the maximum correction.
• The arrows in the corrected direction will turn orange.
• The Keystone dialog box will disappear when the
Keystone function is not operated for four (4)
seconds.
✔Note:
• If you press the RESET button on the remote control while selecting Keystone, the
adjustment will go back to the factory default setting.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Mounting
Ceiling
This function is used to select the installation methods of the
projector. Press the Point 8 or OK buttons to switch between
each mode.
Off . . . . . Cancel the selected installation method.
Ceiling . . Project the image from the ceiling-mounted
projector. The picture is top/bottom and left/right
reversed.
Wall . . . . Project the image from a wall-hanging projector. The
picture is top/bottom reversed.
Wall
Off (Normal)
Rear
When this function is “On,” the picture is left/right reversed. This
function is used to project the image to a rear projection screen.
Press the Point 8 or OK buttons to switch On/Off.
Rear (On)
HDMI setup
Select L1 or L2 with the Point 8 or OK buttons according to the
output signal of video equipment.
L1 . . . . . When the output of video equipment is set
“STANDARD”.
L2 . . . . . When the output of video equipment is set
“ENHANCED”.
The names for the output setting of video equipment vary from
equipment to equipment. For details, refer to the owner’s manual
of video equipment.
HDMI setup
Blue back
When this function is “On”, the projector produces a blue image
while an input signal is not detected. Press the Point 8 or OK
buttons to switch On/Off.
Display
This function decides whether to display the On-Screen Displays.
Press the Point 8 or OK buttons to switch between each mode.
Press the Point 8 or OK
buttons to select L1 or L2
according to the output
signal of video equipment.
On . . . . . . . . . . . . Show all the On-Screen Displays. Use this
function when you want to project images
after the lamp becomes bright enough. The
factory default setting is this mode.
Countdown Off . . Show the input image instead of the
countdown when turning on the projector.
Use this function when you want to project
the image as early as possible even when
the lamp is not bright enough.
Off . . . . . . . . . . . . Hide the On-Screen Displays except;
● On-Screen Menu
● “Power off?”
● “No signal” for Power management (p.37)
● “Please wait ...”
● Color management operation screen
● Panning dialog box when Normal through
is selected in the Screen Menu (p.34).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Capture
Logo
This function decides on the starting-up display from among the
following options. Press the Point 8 or OK buttons to switch
between each mode.
User . . . . . Show the Image you captured.
Default . . . Show the factory-set logo.
Off . . . . . . . Show the Countdown display only.
Power off confirmation
When this function is “On”, the confirmation dialog box with
“Power off?” is displayed when turning off the projector (p.19).
Press the Point 8 or OK buttons to switch On/Off.
Select [Yes] to capture
the projected image.
Capture
This function enables you to capture an image being projected to
use it for the starting-up display or interval of presentations.
Select Capture and press the Point 8 or OK buttons. The
confirmation box appears and select [Yes] to capture the projected
image.
After capturing the projected image, go to the Logo function and
set it to “User”. Then the captured image will be displayed the
next time the projector is turned on.
Select [Yes] to
stop capturing.
To cancel the Capture function, select [No].
✔Note:
• A signal from a computer can be captured up to XGA (1024 x 768).
• The image that has been adjusted in the Image adj. Menu cannot be captured.
• When capturing the image that has been adjusted by the Keystone function, the
adjusted data is automatically reset and the projector captures an image without
keystone correction.
• If the Capture function fails to capture an image or stops capturing halfway, the On-
Screen Menu returns to the Capture item.
• The Capture function cannot be operated with unsupported signals.
• When starting to capture a new image, the previously stored image is cleared even if
you cancel the capturing.
Power management
Power management
For reducing power consumption as well as maintaining the lamp
life, the Power management function turns off the projection lamp
when the projector is not used for a certain period.
When this function is “On” and if the input signal is interrupted
and no button is pressed for more than 30 seconds, the timer
display with “No signal” appears on the screen. It starts the
countdown until the lamp is turned off. The countdown time is set
to five (5) minutes.
When the countdown time has elapsed, the lamp will be turned
off to cool itself down. The POWER indicator is blinking red during
the cooling-off period. When the lamp has been fully cooled down,
the POWER indicator changes to green blinking. In this condition,
the projection lamp can be turned on when the input signal is
reconnected or any button on the top control or remote control is
pressed.
The time left until
lamp off
Press the Point 8 or OK buttons to switch On/Off.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Remote control
Remote control
Two different remote control codes are assigned to this projector:
the factory-set code (Code 1) and the secondary code (Code 2).
This switching function prevents interference from other remote
controls when several projectors or video equipment next to each
other are used at the same time.
When operating the projector in “Code 2”, the code for both the
projector and the remote control must be switched to “Code 2”.
To change the code of the projector:
Press the Point 8 or OK buttons to switch between Code 1 and
Code 2.
To change the code of the remote control:
Press and hold both MENU and IMAGE button on the remote
control for more than 10 seconds to switch between Code 1 and
Code 2.
After changing the code, make sure the remote control operates
properly.
Shutter demo
✔Note:
• When the batteries of the remote control are replaced, the remote control code
automatically returns to the initial code (Code 1).
Shutter demo
Press the Point 8 or OK buttons to start Shutter demo. The
automatic slide shutter closes once with the lamp being turned on
and will open up again. This is used for checking the operation of
the automatic slide shutter.
Cleaning
This function is used to clean the inside of the projector. Using a
blower as well is more effective. (See page 43.)
Press the Point 8 or OK buttons, then the projected image is
blacked out temporarily regardless of whether or not an input
source is selected. The fan starts to operate automatically to help
blowing the dust.
To cancel the cleaning function, press any other button during
cleaning operations.
✔Note:
• The Power management function cannot be operated during cleaning.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
1. Adjust the bright parts with the Bright dialog box.
Panel adjustment
This function is used to get the best picture reproduction of the R
(red), G (green) and B (blue) LCD panels. If the proper adjustment
is not made, you might get vertical noise lines on the screen.
This function should be made more than 10 minutes after turning
on the projector with or without any signal.
A dark environment helps make more accurate adjustment.
Press the OK button or Point 8 button and the Test pattern
screens will appear in the order of R (red), G (green), B (blue). Use
the Point ed7 8 buttons to adjust each pattern as follows:
2. Adjust the dark parts with the Dark dialog box.
1. Adjust the value in the Bright dialog box to minimize vertical
lines in the bright part of the picture.
2. Adjust the value in the Dark dialog box to minimize vertical
lines in the dark part of the picture.
3. Press the Point ed buttons to move on to the next color.
Repeat step 1 and 2 for each R,G,B panel until the vertical
lines of the picture are minimized.
3. Then adjust the Test pattern G and
Test pattern B in the same way.
4. Press the Point ed buttons to display the Check pattern
screen and check the adjustment.
4. Check the adjustment with Check pattern screen.
5. To close this screen and return to the menu, press the OK or
MENU button.
Lamp counter reset
This function resets the lamp replacement counter. When
replacing the projection lamp, reset the lamp replacement counter
with this function. See page 47 for operation.
Factory default
This function restores all setting values except for the user’s logo
and the lamp counter to the factory default settings.
Factory default
Select Factory default and
press the OK or Point
8
buttons. “Return to Factory
default?” will appear.
Select [Yes] and press
the OK or Point
8
buttons, then another
confirmation box will
appear.
Select [Yes] again to
restore to the factory
default settings.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
Input Source Information Display
This is used for checking the status of the image signal being projected and the operation of the projector.
Information Menu
Signal
A color system of the connected video
signal is displayed from among PAL,
SECAM, NTSC, NTSC4.43, PAL-M, PAL-N.
Video or S-video
Component
HDMI
A system mode of the connected video
signal is displayed from among 480i, 480p,
575i, 575p, 720p, 1080i.
A system mode of the connected video
signal is displayed from among D-VGA, D-
480i, D-480p, D-575i, D-575p, D-720p, D-
1080i.
A resolution of the connected computer
signal is displayed.
PC
When there is no signal input, “- - - -” is
displayed.
No signal
Out of recognition
When the connected input source is out of
recognition, “Unknown” is displayed.
H-sync freq.
The horizontal frequency of the input signal is displayed in KHz, or
“- - - -” when no signal.
V-sync freq.
The vertical frequency of the input signal is displayed in Hz, or
“- - - -” when no signal.
Lamp Time
The cumulative lamp operating time is displayed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Warning Indicator
The WARNING indicator shows the state of the function that protects the projector. Check the state of the WARNING
indicator and the POWER indicator to take proper maintenance.
The projector is shut down and the WARNING indicator is blinking red.
When the temperature inside the projector reaches a certain level,
the projector will be automatically shut down to protect its inside.
The POWER indicator is blinking while the projector is being
cooled down. When the projector has cooled down sufficiently (to
its normal operating temperature), it can be turned on again by
pressing the POWER ON-OFF button.
TOP CONTROL
✔Note:
• The WARNING indicator continues to blink even after the temperature inside the
projector returns to normal. When the projector is turned on again, the WARNING
indicator stops blinking.
WARNING
blinking red
Then check the items below.
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if ventilation
slots are not blocked.
– Is the projector not installed near the ventilation duct of air-
conditioning equipment that may be hot? Install the projector
away from the ventilation duct of air-conditioning equipment.
– Are the air filters clean? Clean the air filters periodically or
replace it with a new one.
The projector is shut down and the WARNING indicator emits a red light.
When the projector detects an abnormal condition, it will be
automatically shut down to protect its inside and the WARNING
indicator will be red. In this case, unplug the AC power cord and
reconnect it, and then turn on the projector once again for check.
If the projector cannot be turned on and the WARNING indicator
emits a red light, unplug the AC power cord and contact the
service station for a checkup and repair.
TOP CONTROL
WARNING
emitting a red light
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE AC
POWER CORD CONNECTED UNDER THE ABNORMAL
CONDITION. IT MAY RESULT IN A FIRE OR ELECTRIC
SHOCK.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning the RGB panels
Blemishes such as dust and dirt on the internal optical components of the projector tend to degrade the brightness of the
screen and are likely to appear as a shadow on the screen, which can lead to deterioration of image quality.
This projector is equipped with the RGB panel cleaning holes on the underside for cleaning of the internal parts (such as
optical components) of the projector. When you use the projector for a lengthy period of time or a shadow of dust appears
on the projected screen, clean the inside of the projector.
Using the supplied air blower and with the Cleaning function in the Setting Menu (p.38), you can remove the dusts from the
projector.
✔Note:
• Dust might not be removed completely with these steps. In that case, contact the dealer where you purchased the projector or service center.
CAUTION IN USING THE AIR BLOWER AND THE NOZZLE
● Turn the projector over when using the blower.
● Use only the supplied air blower and nozzle to keep the projector from being out of oder or
CAUTION
damaged. We could not guarantee the malfunction or breakage caused by other tools.
● Never use a commercially available compressed air duster. It causes the interior of the projector to
malfunction with release of cold liquid propellant.
● Put the projector on a soft cloth to prevent scratching the surface.
● Open the hole cover only when you clean the inside of the projector.
PROHIBITED
● Do not look into the holes. A strong light could damage your eyes. (Do not look into the Air intake
vent and Exhaust vent, either.)
● Use the blower and nozzle only to clean the projector. Do not attempt to use them for other
purposes. Do not use the blower and nozzle against persons (particularly to eyes, mouth or ear, and
so on). Be especially careful to ensure that children do not put the blower and nozzle into their
mouth and swallow them.
● Do not attempt to pull the nozzle out of the blower. If the nozzle happened to be pulled out, put it
back into the blower immediately.
● Do not use the blower supplied with this projector (Z4) to clean the Z3 and Z1X.
In the unlikely event that something goes wrong (smoke, a strange sound, an abnormal odor, and such) while you
are cleaning, turn off and unplug the projector immediately, then call the dealer where you purchased the
projector or service center.
If the nozzle is pulled out ....
Put this end of the
nozzle into the
blower.
The nozzle has the stopper. Put the stopper-side of the nozzle into
the blower. Put the nozzle firmly into the blower until the stopper
becomes invisible.
When putting the nozzle into the blower, hold near the stopper so
that it will not break.
Put the nozzle in
until the stopper
becomes invisible.
Make sure not to attempt to pull the nozzle out of the blower.
Stopper
Hold near the stopper
of the nozzle.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning
Clean by using the Cleaning function in the Setting Menu
Turn the projector on and press the MENU button to display
1
the On-Screen Menu. Select the Setting Menu with the
Point ed buttons. Press the Point 8 or OK buttons to
access the sub-menu items.
Select Cleaning and then press the OK or Point 8 buttons.
The screen is blacked out temporarily.
2
3
4
5
6
7
Turn the projector over. Loosen the screw that secures the
hole cover, and then open the hole cover.
Select Cleaning in the
Setting Menu.
Put the blower’s nozzle into a hole.
Loosen the screw that
secures the hole
cover.
Blow air into the projector with the blower watching the
position of the dust from the screen.
When cleaning is done, pull the blower out of the hole and
replace the hole cover and secure it with the screw.
Set the projector back into the right position, then press any
button on the top control or on the remote control to quit the
Cleaning function.
* Do not open the hole cover except when you clean the inside of the projector to
prevent foreign matters from getting into the projector. If it is open especially while
operating the projector, the optical parts could damage.
The nozzle will go no
further than a certain
point when it is put
into the hole. Do not
attempt to push the
nozzle further in, or it
could break and be
stuck inside of the
projector.
Which hole to put the nozzle in?
When you look at the screen:
● When red spots (dust) are particularly noticeable, put the
nozzle into the R panel cleaning holes.
● When green spots (dust) are particularly noticeable, put
the nozzle into the G panel cleaning holes.
● When blue spots (dust) are particularly noticeable, put the
nozzle into the B panel cleaning holes.
Wave the nozzle back and forth inside of the projector.
(Do not attempt to bend the nozzle.)
Use only the supplied blower and nozzle.
Do not use
a
commercially available
compressed air duster. It causes the interior of
the projector to malfunction with release of cold liquid
propellant. We could not guarantee the malfunction of
breakage by using other tools.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning the Air Filters
The air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air
filters become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in a buildup of internal
heat and adversely affect the life of the projector. Clean the air filters by following the steps below.
Cleaning the Air Filter 1 and 2
Press the latch and release it. Take off the filter covers. Do
not try to pull the delicate filter part.
1
Pull out the air filters.
When taking out the Air Filter 2, put your finger on the air
filter’s tab and pull.
2
Air Filter 1
(Intake Vent)
Remove dust and dirt with a soft brush or a vacuum cleaner.
Be careful not to damage the air filters and do not clean
them with water.
When the Air Filter 1 gets dusty and dirty, replace it with a
new one. For ordering the replacement filter, contact your
sales dealer.
3
4
Air Filter 2
(Intake Vent)
Latch
Put the air filters back into the position and close the filter
covers. Do not push the delicate filter part. Make sure that
the air filters are properly and fully inserted.
Press the latch and take
off the filter covers.
CAUTION
Do not operate the projector with the air filters removed.
Dust may accumulate on the LCD panel degrading the
picture quality of the projection mirror. Do not put
anything into the air intake vents. It may result in
malfunction of the projector.
Pull out the air filters.
RECOMMENDATION
We recommend avoiding dusty/smoky environments when
operating the projector. Usage in these environment may
cause a poor image quality.
When using the projector under dusty or smoky conditions, dust
may accumulate on a lens, LCD panels, or optical elements inside
the projector degrading the quality of a projected image.
When the symptoms above are noticed, contact your authorized
dealer or service station for proper cleaning.
Arrows
Put your finger on the air
filter’s tab and pull.
When putting back this air
filter, make sure that the
arrows on the filter are facing
towards the projector.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning the Projection Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that contains
a small amount of non-abrasive camera lens cleaner, or use a lens
cleaning paper or a commercially available air blower to clean the
lens. Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch the
surface of the lens.
When the projector is not in use, make sure that the automatic
slide shutter is closed.
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a dry soft cloth. When the
cabinet is heavily soiled, apply a small amount of mild detergent
and finish with a dry soft cloth. Avoid using an excessive amount
of cleaner. Abrasive cleaners, solvents, or other harsh chemicals
might scratch the surface of the cabinet.
When the projector is not in use, put it in an appropriate carrying
case to protect it from dust and scratches.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replacement
When the life of the projection lamp of this projector draws to an
end, the LAMP REPLACE indicator emits a yellow light. If this
indicator lights yellow, replace the lamp with a new one promptly.
Top Control
The time when the LAMP REPLACE indicator should light is
depending on the lamp mode.
This indicator lights yellow when
the life of the projection lamp
draws to an end.
CAUTION
Allow the projector to cool, for at least 45 minutes
before you open the lamp cover. The inside of the
projector can become very hot.
CAUTION
For continued safety, replace the lamp with the same
type. Do not drop the lamp or touch the glass bulb! The
glass can shatter and may cause injury.
Screw
Lamp Cover
Follow these steps to replace the lamp.
Turn off the projector and unplug the AC power cord. Allow
the projector to cool for at least 45 minutes.
1
Turn the projector over. Loosen the screw that secures the
lamp cover, and then open the lamp cover.
2
Loosen the two (2) screws that secure the lamp. Lift the
lamp out of the projector by using the built in handle.
3
Replace the lamp with a new one and secure it with the two
(2) screws. Make sure that the lamp is set properly. Replace
the lamp cover and secure it with the screw.
4
Lamp
Handle
Connect the AC power cord to the projector and turn on the
projector.
5
Reset the Lamp replacement counter.
See “Lamp Replacement Counter” on the next page.
6
Screws
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
● Model No. of your projector
:
:
PLV-Z4
● Replacement Lamp Type No.
POA-LMP94
(Service Parts No. 610 323 5998)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replacement Counter
Be sure to reset the lamp replacement counter after the lamp is replaced. When the lamp replacement counter is reset, the
LAMP REPLACE indicator stops lighting.
Lamp counter reset
Turn the projector on and press the MENU button to display
the On-Screen Menu. Select the Setting Menu with the
Point ed buttons. Press the Point 8 button to access the
1
sub-menu items.
Select Lamp counter reset and then press the the OK or
Point 8 buttons. “Lamp replacement counter reset?” will
appear. Select [Yes] and then press the OK or Point 8
2
buttons.
Another confirmation dialog box appears, and select [Yes] to
reset the Lamp replacement counter.
Select Lamp counter reset
and press the OK or Point 8
buttons. “Lamp replacement
counter reset” will appear.
3
✔Note:
• Do not reset the Lamp replacement counter without implementing lamp
replacement. Be sure to reset the Lamp replacement counter only after replacing
the lamp.
Select [Yes] and press
the OK or Point
8
buttons, then another
confirmation box will
appear.
Select [Yes] again to
reset the lamp counter.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of
the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described in “Connecting to Video
Equipment” and “Connecting to a Computer” on pages 16 ~ 17.
– Make sure all equipment is connected to an AC outlet and the power is turned on.
– When you operate the projector with a computer and it does not project an image, restart the computer.
Problem:
– Solutions
No power.
– Plug the power cord of the projector into an AC outlet.
– See if the automatic slide shutter is only half-open. When it is half-open, the
POWER indicator blinks orange and the projector cannot be turned on.
(See page 18.)
– See if the Main On/Off switch is on.
– Wait 60 seconds after the projector is turned off to restart the projector. The
projector can be turned on after the POWER indicator turns red. (See page 19.)
– Check the WARNING indicator. If the WARNING indicator lights red, the
projector cannot be turned on. (See page 41.)
– Check the projection lamp. (See page 46)
– Check if the projector is installed on a flat surface.
Image is out of focus.
– Adjust the focus of the projector. (See page 22.)
– Provide proper distance between the projector and the projection screen.
(See page 13.)
– Check the projection lens to see if it needs cleaning. (See page 45.)
– Moving the projector from a cool to warm place may result in moisture
condensation on the projection lens. In such cases, leave the projector off and
wait until condensation evaporates.
No image.
– Check the connection between your computer or video equipment and the
projector. (See page 16 ~ 17.)
– See if the input signal is correctly output from your computer. For some laptop
computers, the setting for the monitor output needs to to be changed when
connecting to a projector. See your computer’s instruction manual for the
setting.
– It takes about 20 seconds to display an image after turning on the projector.
– See if the selected system is corresponding to your computer or video
equipment. (See page 24 ~ 26.)
– Select a correct input source once again through Menu operation.
(See page 25 ~ 26.)
– Make sure the temperature is not out of the specified Operating
Temperature (41°F ~ 95°F (5°C ~ 35°C)).
Image is Left/Right reversed.
Image is Top/Bottom reversed.
– Check the Mounting/Rear item. (See page 36.)
– Check the Mounting item. (See page 36.)
Some displays are not seen
during operations.
– Check the Display item. (See page 36.)
The Remote Control does not work. – Check the batteries.
– Make sure there is no obstruction between the projector and remote control.
– Make sure you are not too far from the projector when using the remote
control. Maximum operating range is 16.4’ (5 m).
– Make sure the code of the remote control is conformed to that of the
projector. (See page 38.)
WARNING:
High voltages are used to operate this projector. Do not attempt to open the cabinet.
after following all operating instructions,
Give the model number and explain about the problem. We will advise you how to obtain service.
If problems still persist
service center.
contact the dealer where you purchased the projector or
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the indicators for projector’s condition.
Indicators
Projector Condition
POWER
red/green/
orange
LAMP
REPLACE
yellow
WARNING
red
The Main On/Off switch is off or the AC power cord is unplugged.
The projection lamp is being cooled down. The projector cannot be turned on
until cooling is completed.
✽
✽
✽
✽
The projector is ready to be turned on with the POWER ON-OFF button.
The projector is operating normally.
The projector is in the Power management mode.
The temperature inside the projector is abnormally high. The projector
cannot be turned on. When the projector is cooled down enough and the
temperature returns to normal, the POWER indicator emits a red light and
the projector can be turned on. (The WARNING indicator keeps blinking.)
Check and clean the air filters.
✽
✽
✽
The projector has been cooled down enough and the inside temperature
returns to normal. When turning on the projector, the WARNING indicator
stops blinking. Check and clean the air filters.
The projector detects an abnormal condition and cannot be turned on.
Unplug the AC power cord and plug it again to turn on the projector. If the
projector is turned off again, unplug the AC power cord and contact the
dealer or service center for servicing and checkup. Do not leave the
projector on. It may cause an electric shock or a fire hazard.
The lamp does not turn on because malfunction occurs or the lamp life
comes to an end.
The automatic slide shutter is not working properly.
✽
• • • green
• • • red
• • • blinking green
• • • blinking red
• • • blinking orange
• • • blinking yellow
• • • off
* When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator becomes
yellow, replace the projection lamp with a new one promptly. Reset the Lamp replacement counter after replacing the lamp. The
time when the LAMP REPLACE indicator should light is depending on the lamp mode. See pages 46 and 47.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Menu Tree
Input
Video / S-Video
Component 1
Component 2
HDMI
Auto
PAL
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
Quit
Computer
RGB(Analog)
RGB(Scart)
Quit
Creative cinema
Pure cinema
Natural
Living
Dynamic
Image
Image adj.
Brightness
Contrast
Color
Tint
Color temp.
-31 ~ +31
-31 ~ +31
-31 ~ +31
-31 ~ +31
High
Powerful
Mid
Vivid
Low 1
Low 2
Low 3
User
-31 ~ +31
-31 ~ +31
-31 ~ +31
-7 ~ +7
Normal
Auto 1
Auto 2
Eco
User image 1
User image 2
User image 3
User image 4
Red
Green
Blue
Sharpness
Lamp Control
Gamma
Progressive
-7 ~ +7
Off
L1
L2
Film
Lens iris
Advanced menu
-63 ~ 0
Lamp iris
Auto / Open / Close
Auto black stretch
Off / L1 / L2 / L3
Contrast enhancement
Off /L1 / L2 / L3
Transient improvement
Off / L1 / L2 /L3
Color management
Gain R/G/B
-15 ~ +15
Offset R/G/B
-15 ~ +15
Gamma R/G/B
-5 ~ +5
Reset
Store
Yes / No
User image 1
User image 2
User image 3
User image 4
Quit
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Overscan
Horizontal
Vertical
Auto adj.
Fine sync
Total dots
0 ~ +10
-100~ +100
-100~ +100
Picture adj.
Setting
Language
English
German
French
Italian
Spanish
Portuguese
Dutch
❖
0 ~ +31
-100 ~ +100
- - - When 480i / 575i input, -8 ~ +8.
❖
Swedish
Finnish
Polish
Hungarian
Romanian
Russian
Chinese
Korean
Japanese
Quit
On / Off
Full
Full through
Zoom
Caption in
Normal
Normal through
Natural wide 1
Natural wide 2
Screen
Advanced menu
Menu Position
Keystone
Mounting
Off
Signal
PAL
Ceiling
Wall
On / Off
L1
L2
On / Off
On
Information
SECAM
NTSC
NTSC4.43
PAL-M
PAL-N
480i
Rear
HDMI setup
Blue back
Display
480p
575i
Countdown Off
Off
575p
Logo
User
720p
1080i
Default
Off
D-VGA
D-480i
D-480p
D-575i
D-575p
D-720p
D-1080i
Power off confirmation
Capture
Power management
Remote control
On / Off
Yes / No
On / Off
Code 1
Code 2
Start
Shutter demo
Cleaning
Resolution for PC input
- - - -
Unknown
Panel adjustment
Test pattern R
Test pattern G
Test pattern B
Check pattern
Yes / No
H-sync freq.
V-sync freq.
Lamp Time
Lamp counter reset
Factory default
Yes / No
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
PLV-Z4 can basically accept the signal from all computers with V, H-Frequency mentioned below and less than 100 MHz of Dot
Clock.
H-Freq.
(kHz)
V-Freq.
(Hz)
H-Freq.
(kHz)
V-Freq.
(Hz)
System mode
System mode
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 400
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
31.47
37.86
37.85
37.50
43.269
37.861
35.00
37.927
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.60
47.90
32.70
49.72
31.020
48.35
68.677
60.023
56.47
59.88
74.38
72.81
75.00
85.00
85.08
66.67
85.039
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.31
71.92
51.09
74.55
60.00
60.00
84.997
75.03
70.07
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 870
1152 x 900
1152 x 900
720p
60.31
44.00
63.48
62.04
61.00
46.90
58.03
64.20
68.68
61.20
61.85
45.00
33.75
28.12
74.92
54.58
79.35
77.07
75.70
58.20
72.00
70.40
75.06
65.20
66.00
60.00
30.00
1080i
1080i
(Interlace)
25.00
(Interlace)
848 x 480
1024 x 768
1024 x 768
1024 x 768
1024 x 768
When the input signal is digital from the HDMI terminal, refer to the chart below.
System
mode
H-Freq.
(kHz)
V-Freq.
(Hz)
59.94/60
59.94/60
50.00
59.94/60
50.00
System
mode
H-Freq.
V-Freq.
(Hz)
59.94/60
50.00
59.94/60
50.00
RESOLUTION
RESOLUTION
(kHz)
––––––
––––––
640 x 480
720 x 480
720 x 575
720 x 480
720 x 575
D-VGA
D-480i
D-575i
D-480p
D-575p
D-720p
D-720p
D-1080i
D-1080i
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
––––––
––––––
––––––
––––––
––––––
––––––
––––––
✔Note:
• You might be able to project images even when signals other than above are inputted, however the functions of the projector could be limited.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Multimedia Projector
Projector Type
15.04” x 4.99” x 11.98” (382 mm x 126.8 mm x 304.3 mm) (not including raised portions)
10.2 lbs (5.0 kg)
(W x H x D)
Dimensions
Net Weight
0.7” wide TFT Active Matrix type, 3 panels
1280 x 720 dots
LCD Panel System
Panel Resolution
2,764,800 (1280 x 720 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p and 1080i
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 40” to 300”
Number of Pixels
Color System
High Definition TV Signal
Scanning Frequency
Projection Image size
Projection Lens
Throw Distance
(Diagonal)
F 2.0 ~ 3.0 lens with f 21.3 mm ~ 42.6 mm with manual zoom and focus
3.9’ ~ 30.2’ (1.2 m ~ 9.2 m)
145 W
Projection Lamp
RCA Type x 1 (Video), RCA Type x 3 (Y, Pb/Cb, Pr/Cr) x 2 and Mini DIN 4 pin x 1 (S-video)
(VGA) HDB 15 Terminal x 1
Video Input Jacks
Computer Input Terminal
HDMI Input Terminal
Service Port Connector
Feet Adjustment
HDMI terminal 19 pin x 1
Mini DIN 8 pin x 1
0˚ to 7.7˚
Voltage and
Power Consumption
Operating Temperature
AC 100 ~ 120 V (2.4 A Max. Ampere), 50/60 Hz (The U.S.A. and Canada)
AC 200 ~ 240 V (1.3 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Remote Control
Power Source
: AA or LR06 1.5V ALKALINE Type x 2
Operating Range : 16.4’ (5 m) / 30˚
Dimensions
Net Weight
: 1.57” x 1.44” x 5.12” (40 mm x 36.5 mm x 130 mm)
: 3.6 oz (102 g) (including batteries)
Owner’s Manual
AC Power Cord
Accessories
Remote Control and Batteries
Video Cable
Air Blower
● The specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny
fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
This symbol on the nameplate means the product is Listed by Underwriters Laboratories
Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of
fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Pixelworks ICs used.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Dimensions
Unit : inch (mm)
5.23 (132.9)
Lens Shift Center
15.04 (382.0)
2.58 (65.5)
Lens Shift Center
7.7˚ (Max.)
11.98 (304.3)
4.99 (126.8)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configurations of Terminals
Video terminal
Terminal : HDMI
Pin Configuration
1
TMDS Data 2+ Input
Ground (TMDS Data 2)
TMDS Data 2- Input
TMDS Data 1+ Input
Ground (TMDS Data 1)
TMDS Data 1- Input
TMDS Data 0+ Input
Ground (TMDS Data 0)
TMDS Data 0- Input
TMDS Clock+ Input
Ground (TMDS Clock)
TMDS Clock- Input
11
12
13
14
15
16
17
18
19
2
3
1
3
5
7
9
11 13 15 17 19
-----
-----
2
4
6
8
10 12 14 16 18
4
SCL
SDA
5
6
19 Pin Type A
Ground(DDC/CEC)
+5V Power
Plug insert detection
7
8
9
10
Computer terminal
Terminal : VGA
Pin Configuration
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
9
-----
10 Ground (Vert.sync.)
11 Ground / -----
12
13 Horiz. sync. Input/Output (Composite H/V sync.)
14 Vert. sync.
15
2
5
1
4
3
-----
-----
10
9
8
7
6
15
12
11
14
13
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
-----
Optional Parts
The parts listed below are optionally supplied. When ordering those parts, give the name and Type No. to the sales dealer.
● Wall Anchor Kit
Type No. : POA-CH-EX02
Type No. : POA-CA-HDMI
Type No. : POA-CA-COMP10
Type No. : POA-CA-SCART
● HDMI Cable
● Component Cable (32.8’/10m)
● Scart-VGA Cable
(This cable is used for RGB Scart 21-
Pin Video output of video equipment.)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in Japan
Part No. 610 324 5843 (1AA6P1P4961-- M4WA)
SANYO Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|