Installation and User Manual
Infinity 24e
Continuous Flow Water Heater
Important.
Read these instructions carefully before attempting installation or use of
this appliance. All work must be carried out by competent persons.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Rinnai UK Warranty..…………………….. …………………………………………………2
Unpacking Rinnai Water Heater………… …………………………………….…………..4
Installation Instructions…………………… …………………………………………………5
Flue Requirements………………………... …………………………………………………8
Dimensions………………………………… …………………………………………………9
Technical Details..………………………… ……………………………………………….10
Features and Benefits……………………. ……………………………………………….11
Important Information…………………….. ……………………………………………….12
Operation without Remotes……………… ……………………………………………….14
Temperature Controls…………………….. ……………………………………………….15
Testing……………………………………… ……………………………………………….25
Gas Pressure Setting…………………….. ……………………………………………….26
Dip Switch Setting………………………… ……………………………………………….28
Error Messages…………………………… ……………………………………………….30
Restarting the Rinnai Water Heater…….. ……………………………………………….32
Wiring Diagram……………………………. ……………………………………………….33
Diagnostic Points………………………….. ……………………………………………….34
Specification……………………………….. ……………………………………………….35
Service Contact…………………………… ………………………………………………36
Commissioning Check List……………….. ………………………………………………36
3
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING RINNAI WATER HEATER
• After unpacking the appliance check for damage, if the heater is damaged contact
your supplier immediately. Do not install a damaged appliance before checking
with your supplier.
• One remote control and heater accessories pack are inside the carton.
• Check that the appliance supplied is the correct gas type for the installation. Refer
to the data plate located on the left-hand side of the appliance.
• Remove the heater and the accessories from the carton, and check that all the
parts are included . The remote control cable is provided with spade connectors.
Remote Control Parts
Quantity
Diagram
Description
Temperature con-
troller MC-91-1A
1
Cable clamp
Cable Clamp
1
1
5
1
1
Spade connectors
Control cable 20
metres
Clamp screw
Unit Mounting Fasteners
Quantity
Diagram
Description
Screw
5
5
Screw
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
IMPORTANT INFORMATION
1. Gas safety (Installation & Use) regulations 1998 are the ‘Rules in force’. In your
own interest and that of safety, it is law that all gas appliances are installed by
competent persons in accordance with the above regulations. Failure to install
appliances correctly could lead to prosecution. Other persons should NOT attempt to
install this equipment.
2. Unpack the appliance and check it carefully. If it appears to have any defects or
damage DO NOT INSTALL, contact your supplier.
3. This appliance is for normal hot water supply only and should not be used as pool or
spa water heater.
4. The heater must be installed in the vertical position with the gas and water
connections on the underside pointing vertically downward.
5. Installation must be carried out in accordance with the current issue of the following:
Building regulations issued by the Department of the Environment and
Building Standards (Scotland) Regulations.
I.E.E. Wiring regulations for electrical installations.
Gas safety (Installation and Use) Regulations current issue.
BS 5546
BS 5440
BS 6891
BS 5482
BS 6700
Local byelaws
Water regulations
Health and safety at work etc. Act 1974
Such other specifications and regulations that may supersede or complement the
above documents.
Please be sure that you are fully aware of your obligations and responsibilities
under these regulations.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS - POSITIONING
General Installation Information.
External Installations.
The Rinnai Infinity 24e is for external mounting only.
The unit is classed as a Category A3 flueless appliance as described by CEN CR1749.
Although BS 5440 does not relate directly to heaters in this category the rules must be
followed when positioning the appliance, especially with regard to other appliances,
openings, and boundaries. Figure C.1 from BS5440-1:2000 is provided for your
guidance.
The appliance must be mounted on a vertical wall or structure with the water and the gas
connections on the underside pointing towards the ground.
THIS APPLIANCE MUST NOT BE USED AS A DOMESTIC SPA OR SWIMMING
POOL HEATER.
Appliance Location.
The appliance should be placed as close as practicable to the most frequently used hot
water outlet point or points to minimise the delay time for hot water delivery. For
installations where the distance between the unit and hot water outlet points is
considerable, the appliance can also be fitted in a 'flow and return system' which
minimises the waiting time for hot water delivery. Alternatively, multiple appliances can
be strategically placed to service outlet points with minimal delay time. Contact Rinnai
for further information.
Location of the appliance flue terminal must be in accordance with the clearances shown
on page 8. Ensure that the flue terminal and hot water outlet connection cannot be
touched by children. The appliance must be clear of obstructions and shrubbery.
The wall or structure on which it is mounted must be capable of supporting the weight of
the appliance (18 kg) and associated pipework. Ensure that suitable screws or bolts are
used to secure the water heater to the wall. Bracket and fixing hole locations are shown
on page 9. The top bracket has a keyhole slot so that the appliance can be hung on one
screw, and then the other fixings can be added to secure the unit.
The appliance must be in an accessible location. Sufficient clearances shall allow
access to, and removal of, all serviceable components. The appliance should not be
mounted higher than 3.5 metres from the ground or floor level unless the customer can
arrange permanent and safe access or can arrange another means of access, for
example, by means of scissor or boom lifts.
Multiple heater installations can be installed with the heaters manifolded together.
The heater draws combustion air through the casing for the external model.
Heater guards and pipe cover boxes for security and safety are available from Rinnai.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS - CONNECTIONS
Water Supply.
Where the water supply pressure exceeds 12 bar, an approved pressure reducing
device is required at the inlet of the appliance. To achieve the rated flow a minimum
water supply pressure of 1.4 bar is required at the appliance inlet. The unit will operate
at lower supply pressures but the rated flow will not be achieved. Contact Rinnai for
'gravity fed' or 'low pressure' hot water installations.
Water pipe sizing and layout should be designed correctly to ensure the given water
flows from the Rinnai Infinity are available. All hot water pipework should be insulated to
optimise maximum performance and energy efficiency.
Water Connection.
Connect the hot and cold water supply pipes. An approved isolation valve and strainer
MUST be installed in the cold water inlet pipe. An approved isolation valve should be
installed in the hot water outlet pipe. There must be a union or release fitting on the
heater side of the isolation valves. A non return valve is not required unless dictated by
local regulations. A pressure relief valve should be installed in the pipework to
discharge safely into a suitable drain when the system has a flow and return, or tank.
Positions of the cold water inlet, hot water outlet and gas connections are shown on
page 9. All connections are ¾ inch BSP. This is NOT an indication of the pipe sizes
required.
If the heater is in a hard water area a suitable water conditioning device should be in-
stalled to prevent the build up of limescale within the heat exchanger. Heat exchangers
damaged by scaling are not covered by the manufacturers guarantee. Guidelines are
given below. If the local water exceeds these values the heater must be protected.
Total Dissolved
Solids (TDS)
Description
pH
Total Hardness
200 mg/litre
Chlorides
Magnesium
10 mg/litre
Calcium
Sodium
Iron
Maximum Recommended
Levels
6.5 - 9.0
600 mg/litre
300 mg/litre
20 mg/litre
150 mg/litre
1 mg/litre
Gas Connection
Check pipe sizing required for the heater input. The heat input for the Infinity 24e is 52
kW. Refer to BS6891 (Natural Gas) and BS5482 (Propane) for guidance on correct pipe
sizing calculation.
Check that the size of the gas meter and pipework will be sufficient for all appliances on
the main. Sufficient gas must be available at the appliance if correct operation is to be
expected. An approved gas isolation valve must be fitted at the gas inlet. A union or
release fitting should be installed after the isolation valve.
Electrical Connection.
The appliance must be earthed. The appliance is suitable for 230VAC – 50hz mains
only and all wiring must be carried out to the I.E.E regulations latest edition. The heater
electrical supply must be provided with a fused (3A) local isolator with a contact
separation of 3mm minimum on all poles for servicing. Observe polarity and ensure that
wiring is correctly restrained.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FLUE REQUIREMENTS - POSITIONING
Dimension Terminal Position
Distance
A
B
Directly below an opening, air brick, opening windows, etc.
Above an opening, air brick , opening window, etc.
300mm
300mm
C
D
E
F
G
H
I
Horizontally to an opening, air brick , opening window, etc.
Below gutters, soil pipes or drain pipes.
Below eaves.
300mm
75mm
200mm
200mm
150mm
200mm
300mm
600mm
1200mm
Below balconies or car port roof.
From a vertical drain pipe or soil pipe.
From an internal or external corner.
Above ground, roof or balcony level.
From a surface facing the terminal.
From a terminal facing a terminal
J
K
From an opening in a car port. ( e.g. door, window) into a dwell-
ing
L
1200mm
M
N
O
P
Vertically from a terminal on the same wall.
Horizontally from a terminal on the same wall.
From the wall on which the terminal is mounted
From a vertical structure on the roof.
1500mm
300mm
N/A
N/A
Q
Above an intersection with roof.
N/A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DETAILS
Infinity Model
Units
Infinity 24e
Installation
External
0.8
Nat Gas Press Low
Nat Gas Press High
LPG Press Low
LPG Press High
Height
mbar
mbar
mbar
mbar
mm
9.0
1.7
22.6
600
350
170
18
Width
mm
Depth
mm
Weight
kg
Flue System
Temp. Range Controllers
Forced Exhaust
37 - 75
deg C
Temp. Range without
Controllers
37,40,43,50,
55*,65,75
deg C
Direct Electronic
Ignition
Ignition
Gas Consumption Low
Nat Gas
5.8
5.8
kW
LPG
kW
Gas consumption High
Nat Gas
52
52
kW
LPG
kW
Max Flow raised 33C
Min Operation Flow
Water Pressure Nom.
Power Supply
18
L/min
L/min
bar
2.7**
1.4 - 10
230 V / 50 Hz
Elec. Consumption Standby
(with 1 remote connected)
6
Watts
Elec. Consumption Run
55
Watts
Watts
Elec. Consumption
Anti-frost Heaters On
100
* Factory Setting
**Minimum operation flow based on temperature setpoint and inlet conditions.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
FEATURES AND BENEFITS
Congratulations on purchasing the Technologically Advanced, Temperature Controlled,
Rinnai Hot Water System.
• The Rinnai Infinity 24e NEVER RUNS OUT of hot water. As long as electricity,
water, and gas supplies are connected, hot water is available when hot water taps are
open.
• Built into the main micro-processor is the facility to LIMIT THE MAXIMUM
TEMPERATURE of the hot water supplied. The water temperature may be limited to
various maximum temperatures. This is particularly useful when the hot water unit is
installed where young children or the infirm may be using the hot water. The Infinity
24e is delivered with a preset temperature of 550C. If required, the temperature limits
can be changed by an authorised person. For further information, please contact
Rinnai.
• The Rinnai Infinity external unit is a powered flue appliance. This makes it
COMPACT, saving both floor and wall space.
• The temperature of outgoing hot water is CONSTANTLY MONITORED by a BUILT-
IN SENSOR. If the temperature of the outgoing hot water rises to more than 3°C
above the selected temperature the burner is shut OFF and only turned ON again
when the temperature falls to below the selected temperature.
• The burner lights automatically when the hot water tap is opened, and distinguishes
when the tap is closed. IGNITION IS ELECTRONIC, so there is no pilot light. When
the hot water tap is off, no gas is used.
• Up to three temperature controllers can be mounted remotely from the heater. This
offers the following additional features:
Localised temperature setting.
Diagnostic message.
• ‘Deluxe’ Temperature Controllers are an optional extra. These provide functions
including Bath Fill, Voice Prompt, and Clock Setting.
• Temperatures selected at the controllers are retained in the SYSTEM MEMORY.
• Operating NOISE LEVEL IS VERY LOW.
• ERROR MESSAGES ARE DISPLAYED on the Temperature Controllers, assisting
with service.
• FROST PROTECTION device built in as standard.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
IMPORTANT INFORMATION
Excessively hot water is dangerous, especially for young children and the infirm. The
water heater allows you to control the temperature of your hot water to safe levels.
Water temperature over 50ºC can cause severe
burns instantly or even death from scalding.
Children, disabled and the elderly are at the
highest risk of being scalded by excessively hot
water.
Always test the temperature of the water before
bathing or showering.
Burns from hot water taps can result in very
severe injuries to young children.
Hot water at 65°C can severely burn a child in less
than half a second. At 50°C it takes five minutes.
Burns can occur when children are exposed
directly to hot water or when they are placed into a
bath which is too hot.
Do stay with children
whenever they are in the bathroom.
• Consider child—resistant taps
Do take them out of the bathroom if
you need to answer the phone or
door.
or inexpensive tap covers,
both of which prevent a child’s
hand from turning on the tap.
Do test the temperature of the water
with your elbow before placing your
child in the bath.
• Consider reducing the
temperature of the water
supplied to the hot tap to
500C.
Do make sure that the tap is turned
off tightly.
DO
This approach can be extremely
valuable because it requires a
one time action for a long term
reduction in risks of scalds.
This type of automatic protection
is important during times when a
parent or carer has been
distracted.
Do consider setting your Rinnai
Infinity 16e at a maximum
temperature of 500C.
Do install a child proof tap cover
OR,
Do install a child resistant tap.
Do not leave a toddler in the care of
another small child. The older child
may not have safely set the temperature.
DO
NOT
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
IMPORTANT INFORMATION
Always check water temperature before
Hot water may go out without warning at
use.
low water flows.
OFF
Refer to warning about hot water on
page 12 for important safety information.
The Infinity 24e controls the water
temperature automatically. For high
temperatures it may reduce the flow. The
water from the hot tap may be reduced
after the temperature shown on the
remote control is raised. The water flow
may also vary with the temperature of the
incoming water supply.
If freezing temperatures
are expected, turn off the
water and gas, and
drain the water
heater.
1. Water Off
2. Gas Off
3. Drain Water
If the power is left on the
Automatic Frost Protection
will prevent the unit from
Freezing. Frost protection
is standard on the external
units.
Keep flammable materials, trees, shrubs,
chemicals etc. away from the heater.
Do not touch the unit cover or the flue
outlet. Do not insert objects into the flue
outlet.
On cold days steam may be discharged
from the flue outlet. This is normal, do
not be alarmed. It does not indicate a
fault.
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
OPERATION WITHOUT REMOTES
Rinnai Infinity products have no pilot light and when installed without Temperature
Controllers, the appliance will operate automatically as soon as a hot water tap is
opened.
The burner ignites with electronic ignition and the flame extinguishes as soon as water
flowing through the appliance stops.
Turn On by opening the hot water tap
Rinnai Infinity water heaters without controllers are factory pre-set to a temperature limit
of 55°C. Other limits, lower or higher, are available on request for the Infinity range.
Temperature controllers are available that allow precise digital temperature control.
Higher temperatures may be necessary for circulation loop systems.
Controllers can be easily added at any time after installation.OTE
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
TEMPERATURE CONTROLS - GENERAL
When deciding on the best position for the temperature controls, the following points
should be taken into account.
• Fit the controls out of reach of children (suggested height from the floor 1.5m.)
• Avoid positions where the controllers will become hot. Do not fit them near stoves or
ovens, or above radiators or heaters.
• If possible, avoid exposure to direct sunlight or positions where bright lights will make
the digital display difficult to read.
• Position away from areas where the controller will be prone to splashing by cooking
products such as oils and fats.
• The temperature controllers are water resistant, however they should be positioned
away from areas where direct or persistent splashing could occur.
• Refer to the I.E.E electrical wiring regulations current edition for location requirements
in shower and bath areas.
• The cables to the temperature controller carry only 12VDC (extra low voltage.)
• When using more than one temperature controller the signal cable should be run in
parallel. That is, from controller to controller to heater, or from each controller to the
heater. Do not wire the controllers in series.
The installation in every application will vary, therefore the temperature controller cable
has been provided so that you may cut the length accordingly and fit the spade
connectors, ensuring a good connection.
Cables are simply ‘piggy-backed’ at the water heater or at the primary temperature
controller. Polarity is not important when connecting the cables, either colour wire can
be connected to either terminal at both the heater or primary temperature controller. If
more cable is needed any cable with similar specification to the cable supplied with the
controller can be used. Maximum length is 50 metres.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
TEMPERATURE CONTROLS - INSTALLATION
Universal Temperature Controller
MC-91-1A
1. Determine the most suitable position for the
temperature controller.
2. Drill 3 holes in the wall as shown in fig. 1, one
for the cable and two for the securing screws.
Ensure holes are drilled deep enough. Fit wall
plugs if needed. (ensure controller is level.)
3. Run the cable provided through the hole in the
wall ensuring that the end fitted with the
connector is nearest the controller. (fig. 2.)
4. Remove the face plate from the controller using
a flat screwdriver. Take care not to damage the
cover (fig. 3.)
5. Connect the cable to the temperature controller.
6. Fix the controller to the wall and fasten with the
phillips head screws supplied as shown in (fig.
4.)
7. Remove the protective plastic film from the
controller face as shown in fig. 4.
8. Replace the face plate.
NOTE
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
TEMPERATURE CONTROLS - INSTALLATION
Connecting One or Two Controllers
1. Isolate the power supply.
2. Remove the front cover from the Appliance (4
screws) fig. 1.
3. Thread the cable through the cable access hole
at the base of the appliance.
4. Connect the spade connectors to the terminals
marked "Remote Control" on the printed circuit
board (fig.2). Polarity is not important. Either
wire colour can be connected to either terminal.
5. Replace cover of the Appliance. Ensure that the
special earth screw is placed at the bottom right
hand corner for earthing purposes.
Connecting Three Controllers
1. Isolate the power supply.
2. Remove the front cover from the Appliance (4
screws) fig.1.
3. Thread the cables through the cable access
hole at the base of the appliance.
4. Cut the spade connectors from two controller
cables (4 connectors should be cut off) and
discard. Connect the wires and terminate into
two new spade connectors as shown in fig. 3.
5. Thread the 3 cables through the cable access
hole at the base of the appliance. Connect the
4 spade connectors to the terminals marked
“Remote Control" on the printed circuit board
(fig.2). Polarity is not important. Either wire
colour can be connected to either terminal.
6. Replace cover of the Appliance. Ensure that the
special earth screw is placed at the bottom right
hand corner for earthing purposes.
Connecting Four Controllers
1. Isolate the power supply.
2. Remove the front cover from the Appliance (4
screws) fig.1.
3. Cut the spade connectors from all four controller
cables to be connected to the appliance (8
connectors should be cut off) and discard.
Connect the wires from two remotes and
terminate into two new spade connectors as
shown in fig. 3.
4. Repeat for remaining two remotes.
5. Thread the 4 cables through the cable access
hole at the base of the appliance. Connect the 4
spade connectors to the terminals marked
“Remote Control" on the printed circuit board
(fig.2). Polarity is not important. Either wire
colour can be connected to either terminal.
5. Replace cover of the Appliance. Ensure that the
special earth screw is placed at the bottom right
hand corner for earthing purposes.
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
TEMPERATURE CONTROLS
The purpose of a Temperature Controller is to enable the user to have complete control
over the hot water supply. Used correctly, the hot water unit will supply hot water at the
temperature selected, even when the water flow is varied, or when more than one tap is
used. Adjustments to the operation of your hot water unit can be made with any of the
Temperature Controllers. Each Temperature Controller can be individually programmed.
Up to four Universal and Deluxe Temperature Controllers can be fitted with the Infinity
24e. Universal Controllers allow temperature selection only and come as standard with
the water heaters. Deluxe Temperature Controllers are an optional extra. These
controllers have temperature selection, bath fill, voice recognition, and time clock
functions. When more than one Universal Controller is used one may be set as the
Master Controller to allow higher temperatures.
Various water temperatures (°C) can be selected as follows:
Universal Controller:
37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 48, 500C
Master Universal Controller:
37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 48, 50, 55, 60, 65°C
Deluxe Bathroom Controller:
Hot Water Delivery: 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 48, 50°C
Bath fill Delivery: 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48°C
Deluxe Kitchen Controller:
37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 48, 50, 55, 60, 65°C
If a temperature 43°C or higher is selected on any controller and this temperature is then
decreased to below 43°C and increased again whilst the water is running, the maximum
selectable temperature will become 43°C. This provides additional safety for the
consumer.
Suggested temperatures are:
Kitchen 50°C - 65°C*; Shower 39°C - 43°C; Bath fill 39°C - 45°C
* This temperature may not be available on all installations.
These temperatures are suggested starting points for selection. You may find higher or
lower temperatures are more comfortable. Maintaining lower temperatures helps to save
energy. To obtain water temperatures lower than 37°C simply add cold water.
Up to four controllers can be used for one Infinity 24e. When multiple temperature
controllers are used they allow the temperature to be set from various locations by
pushing the transfer button which gives that controller priority over the system. The
temperature selected by the controller with priority will be available to all outlets.
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
TEMPERATURE CONTROLS - OPERATING
Remote temperature controllers are a feature that provides control over the water
temperature. Rinnai Infinity water heaters can be operated with 1, 2, 3, 4 or no
temperature controllers. The Universal controller MC-91-1A comes as standard with all
Infinity water heaters.
NOTE:
Each time a button is pressed, a BEEP will sound.
The BEEP sound can be muted by depressing the Temperature Controller Up and Down
buttons simultaneously for more than 3 seconds.
This can be done for each Temperature Controller.
To return to original settings, repeat this step.
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
TEMPERATURE CONTROLS - OPERATING
Using 1 Universal Temperature Controller.
Press the On/Off button on the temperature controller.
The ON indicator will glow on the Temperature Controller.
This indicates that the heater is ready to supply hot water
when a tap is opened.
Adjusting Temperature
Simply press the Hot Water Temperature Up or Down arrow
button until the desired temperature is displayed on the
digital display.
To operate the heater, simply turn any hot water tap on. This
will automatically light the burner providing hot water. The
red In Use indicator will glow on the temperature controller.
Caution: Always check water temperature before use.
With the hot water tap open and a temperature of 430C or higher selected,
if the temperature is decreased below 430C, and then raised again the
maximum available temperature will be 430C. For safety reasons
temperature ‘priority’ cannot be transferred between controllers when a
hot water tap is open.
Note:
Download from Www.Somanuals.co2m0. All Manuals Search And Download.
TEMPERATURE CONTROLS - OPERATING
Using 2 or more Universal Temperature Controllers.
Switching the system ON.
The hot water system and all controllers can be
switched ON and OFF from any controller by pressing
the On/Off button as shown. When the system is
turned ON the water temperature display will be lit.
During normal operation the system is left ON. Do
not push the On/Off button when water is running.
Using hot water.
Ensure the system is switched On by verifying the
temperature display is lit. Ensure the controller has
priority by verifying the Transfer LED indicator is lit. If
it is not then press the Transfer button once. This
gives the local controller priority of temperature over
the system.
Select the desired temperature using the Hot water
temp. buttons. The selected temperature will be
displayed on all controller displays. This is the water
temperature which will be supplied from the heater.
Bathroom temperatures should be no more than 500C.
Open the hot water tap. The appliance
will be activated and the In Use
indicator will be lit.
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
TEMPERATURE CONTROLS - OPERATING
Using 4 Universal Temperature Controllers.
You will need to activate the fourth controller.
STEP 1:
STEP 2:
On the Master controller press and hold the Transfer and On/Off buttons
simultaneously (see fig 2.) until a “beep” is heard (approx. 5 seconds)
Check that the display on all Four controllers is lit
and displaying a temperature when switched on. If
any ONE of the controllers displays two dashes (see
fig 1.) in the display repeat STEP 1.
Note:
If the master controller is replaced, repeat STEP 1 above for the new controller.
Download from Www.Somanuals.co2m2. All Manuals Search And Download.
TEMPERATURE CONTROLS - OPERATING
Using High Temperature Display Controllers.
You will need to program the Master controller if you want to display and use
temperatures over 500C. Programming only needs to be done on Master universal
controllers; other universal controllers will not allow this, and Deluxe Kitchen Controllers
are supplied already programmed to allow high temperatures. Temperatures in
bathrooms should never exceed 500C.
STEP 1: On the Master controller only press and hold the Transfer and On/Off
buttons simultaneously (see fig 2.) until a “beep” is heard (approx. 5 seconds)
STEP 2: When the Primary controller is switched on it should be possible to select
temperatures higher than 50ºC. If not repeat STEP 1.
Note:
If the master controller is replaced, repeat STEP 1 above for the new controller.
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
TEMPERATURE CONTROLS - OPERATING
To turn off your hot water system.
During normal operation the system is left on.
To turn the system off simply press the On/Off
button on any temperature controller (where
fitted). This will shut the water heater down
completely including the temperature controller
digital display.
The on indicator will go out.
If hot water taps are opened when the Rinnai
Infinity is off, cold water will flow from the taps.
If the system is to be left off over the winter be
sure to drain it down if there is a possibility of
freezing temperatures.
Additional safety features.
Whilst the hot water tap is open, the following
safety features apply:
• Temperature selection cannot be transferred.
• If a temperature of 430C or higher selected,
and the temperature is decreased to below
430C, and then raised again the maximum
available temperature will be 430C.
• Other controllers are unable to change the
delivery temperature of the water.
Note
The temperature of the outgoing water is constantly monitored by a built in
sensor. If the temperature of the outgoing hot water rises to more than 3ºC
above the selected temperature shown on the digital display, or the preset
limit if controllers are not fitted, the burner will automatically go out. The red
operation indicator will also go out. The burner will ignite again once the
outgoing hot water temperature falls to that shown on the digital display (or
the pre-set limit of the Rinnai Infinity heater).
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
TEMPERATURE CONTROLS - INFORMATION
Do not push the On/Off button on the
Master controller after transferring priority
of temperature selection to a Secondary
controller as the system will shut down.
Temperature priority can not be switched
to another controller when the water is
flowing through the water heater.
500C
Do Not Turn OFF
the Master
Controller
Controller 1
in use
Controller 2
cannot take
priority
If a temperature higher than 50ºC has
been selected on the Master controller
and priority of temperature selection is
transferred to another controller (or it is
turned off), then back again (or turned on
again), the temperature on the Master
controller will automatically drop to 50ºC.
If the set point is less than 500C it will not
alter. This is a safety feature.
Do not clean the remote control with
solvents or detergents. Use only a soft
damp cloth.
Master
Another
Master
Controller
Controller
Controller
Depending on the weather conditions
and the length of the pipe between the
heater and the tap in use, there may be a
variation between the temperature dis-
played at the controller and the tempera-
ture at the tap.
If a temperature higher than 420C has
been selected on the Universal control-
ler and priority of temperature selection is
transferred to another controller (or con-
troller is turned OFF), then back again (or
turned ON again), the temperature will
automatically drop to 420C. If the set
point is less than 420C it will not alter.
This is a safety feature.
480C
Universal
Another
Universal
Controller Controller Controller
Download from Www.Somanuals.co2m5. All Manuals Search And Download.
TESTING
1. Purge gas, hot water and cold water supply lines before making the final connection
of the water heater. Swarf in either the gas or water supplies may cause damage.
2. Turn on gas and cold water supplies.
3. Test for water leaks and gas escapes near the unit.
4. Isolate gas and electric supply. Remove test point screw located on the inlet gas
valve connection inside the heater and attach pressure gauge.
5. Turn the power on at the switch and turn on gas. Warning: There are 230V AC live
supplies inside the heater.
6. If remote controllers are fitted, turn the controller on, select the maximum delivery
temperature and open ALL available hot water outlets. If remote controllers are not
fitted, simply open all available hot water outlets. (CAUTION: Ensure building
occupants do not have access to hot water outlets during this procedure).
7. The gas pressure check must be carried out with all other appliances on the same
main operating at maximum capacity to ensure that there is sufficient gas pressure.
8. With all other appliances operating the pressure at the test point on the inlet to the
gas valve should read 20 mbar for Natural Gas. For LPG (Propane) the pressure
should be 37 mbar. If the pressure is lower, the gas supply is inadequate and the
water heater will not operate to specification. Check gas meter, regulator and
pipework for correct operation/sizing and rectify as required. Note that the gas
regulator on the appliance is electronically controlled and factory pre-set. Under
normal circumstances it does not need adjustment during installation.
9. Close hot water outlets.
10.Inspect and clean the strainer and the filter located on the cold water inlet pipe. This
procedure may need to be repeated to ensure the strainer remains clear.
11.If temperature controllers are fitted, it is necessary to test their operation through the
complete range of functions.
12.Confirm the hot water delivery temperature using a thermometer. If controllers are
fitted, compare the measured value to the set point.
13.After testing is completed, explain to the user the functions and operation of the
water heater and temperature controllers.
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
GAS PRESSURE SETTING
The working gas pressure on the water heater is electronically controlled and factory set.
Under normal circumstances it does not require adjustment during installation. Perform
this procedure only if the unit is not operating correctly and all other possible causes for
incorrect operation have been eliminated. Contact Rinnai UK before
attempting to alter the gas pressure. Failure to do so could void
the warranty.
1. Turn 'OFF' the gas supply.
2. Turn 'OFF' 230V power supply.
3. Remove the front cover from the appliance.
4. Check gas type switch no.1 of SW1 (fig. 1) is
in the correct position for the type of gas (Nat.
or LPG) you are using. (SW1 is top set of
switches.)
5. Attach pressure gauge to burner test point. (fig. 2)
(fig 1)
off
on
off
on
SW1
SW1
1
2
3
4
5
6
7
8
-Nat. Gas
1
2
3
4
5
6
7
8
-LPG
6. Turn 'ON' the gas supply.
7. Turn 'ON' 230V power supply.
Forced Low
off on SW2
1
2
3
8. If remote controllers are fitted, turn the unit
'ON' at the master controller, select the
maximum delivery temperature and open a
hot water tap fully. (CAUTION: Ensure
building occupants do not have access
to hot water outlets during this
procedure.)
(fig 3)
9. Set the appliance to 'Forced Low'
combustion by setting No. 2 dipswitch of the
bottom set of dip switches (SW2) to 'ON'. (fig
3)
LEGEND:
Black Section indicates
position of dip switch.
10.Check the burner test point operating
pressure.
OFF ON
OFF
OFF ON
ON
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
GAS PRESSURE SETTING
11.Remove rubber access plug and adjust the
regulator screw on the modulating valve (fig. 4
and 4a) as required to the pressure below.
N.G
0.8 mbar
Propane 1.7 mbar
12.Lock the regulating screw on the modulating
valve.
13.Set the appliance to 'Forced High' combustion
by setting both no. 2 and no. 3 dipswitches of
the bottom set of switches (SW2) to 'ON'.
(fig.5) Ensure maximum water flow.
(fig 4a)
14.Check the burner test point pressure.
Forced High
off on SW2
15.Adjust the high pressure potentiometer on the
Printed Circuit Board below SW2 (fig. 6) to the
pressure shown below. The potentiometer is
very sensitive, turn no more than a few de-
grees at a time; then let the pressure settle
down before turning it more.
1
2
3
(fig 5)
N.G
9.0 mbar
Propane
22.6 mbar
16.IMPORTANT: Set dip switch no. 2 and no. 3
on the bottom set of switches (SW2) to 'OFF'
to return the appliance to 'Normal' combustion.
(fig. 7)
17.Close hot water tap.
(fig 6)
18.Turn OFF the gas supply and 230V power
supply.
Normal
19.Remove pressure gauge, and replace sealing
screw.
off on SW2
1
2
3
20.Turn 'ON' the gas supply and 230V power
supply.
(fig 7)
21.Operate unit and check for gas leaks at test
point.
22.Replace the front cover of the appliance.
CAUTION
Download from Www.Somanuals.co2m8. All Manuals Search And Download.
DIP SWITCH SETTING
Dip Switch Positions Explained
OFF ON SW1
1
2
3
4
5
6
7
8
-
-
-
-
-
-
Gas Type
LEGEND:
Black Section indicates
position of dip switch.
Computer Programming
Computer Programming
Temperature
Temperature
Temperature
OFF ON
OFF
OFF ON
ON
Temperature
Temperature
OFF ON SW2
1
2
3
-
-
-
Computer Programming
Combustion
Combustion
Dip Switches Explained
GAS TYPE
LPG
NAT GAS
OFF ON SW1
OFF ON SW1
1
2
3
4
5
6
7
8
off
1
2
3
4
5
6
7
8
on
COMBUSTION
NORMAL
FORCED LOW
FORCED HIGH
OFF ON SW2
OFF ON SW2
1
OFF ON SW2
1
1
2
3
off
off
2 on
3 off
2 on
3 on
COMPUTER PROGRAMMING
OFF ON SW2
1
2
3
-
Switch is always in the OFF position for the
Infinity 24e
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
DIP SWITCH SETTING
Temperatures - Remotes Connected
off on SWI
off on SWI
off on SWI
off on SWI
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
40 deg C
43 deg C
50 deg C
55 deg C
off on SWI
off on SWI
off on SWI
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
60 deg C
65 deg C
75 deg C
Temperatures - Remotes Not Connected
off on SWI
off on SWI
off on SWI
off on SWI
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
40 deg C
43 deg C
50 deg C
55 deg C
off on SWI
off on SWI
off on SWI
off on SWI
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
4
5
6
7
8
60 deg C
65 deg C
75 deg C
85 deg C
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
ERROR MESSAGES
Rinnai water heaters have the ability to check their own operation continuously. If a fault
occurs, an error code will flash on the Digital Display if you have temperature controllers
installed. This assists with diagnosing the fault, and may enable you to overcome a
problem without a service call. Please quote the code displayed when enquiring about
service. Error codes flash.
Code
Fault
Remedy
Displayed
-
Noticeable reduction in water
flow
Inlet water filter needs to be cleaned.
Not enough combustion air
Check for physical blockages around
air intake or exhaust. Check
combustion fan.
10
No Ignition / Gas supply
Check gas valves, gas supply and
sparker unit.
11
12
Flame failure / Low Gas flow
Check gas valves and gas supply.
Check flame rod.
Check exhaust is clear.
Check remote control.
Remaining flame safety device
Over temperature warning
Service Call
Service Call
Service Call
14
16
32
Outgoing water temperature
sensor faulty
Heat Exchanger Thermistor
Error
Service Call
33
Gas modulating valve faulty
Combustion fan failure
Water Flow Control Device
Micro-processor failure
Flame rod circuit error
Service Call
Service Call
Service Call
Service Call
Service Call
52
61
65
71
72
Fan Failure
Service Call
90
* In all cases, you may be able to clear the Error code by turning the hot water tap OFF,
then ON again. If this does not clear the error, try pushing the On/Off button OFF then
ON again. If the Error Code still remains contact Rinnai or your nearest service agent for
advice.
** Faults caused by insufficient gas/water supply or gas/water quality and installation
errors are not covered by the manufacturer’s guarantee.
Download from Www.Somanuals.co3m1. All Manuals Search And Download.
ERROR MESSAGES
Troubleshooting without controllers
If you have not installed temperature controllers and experience the following
symptoms, please carry out the suggestions below. If symptoms continue, please
contact Rinnai for advice.
Fault
Remedy
Heater does not attempt Check the power is on at the heater.
to start at all.
Check the cold water valve supplying the heater is open.
Heater starts then shuts Check the power is on.
down immediately.
Check the gas valve at the heater and at the gas meter is fully open.
Open the hot water tap fully.
Heater starts then the
water goes cold.
Check the power is on.
Open your hot water tap further or try another hot outlet.
NOTE: Faults caused by insufficient gas/water supply or gas/water quality and
installation errors are not covered by the manufacturer’s guarantee.
Installations with circulation pumps
With temperature controller fitted.
If you have an installation using a secondary circulation pump this must be
switched off so that there is no flow through the heater when starting or after a
power failure. If the pump is running the unit will not operate (no display on the
controller). Isolate pump then start heater before restarting pump. This is a safety
feature.
The pump should also be fitted with a thermostat to prevent the return temperature
reaching the heater set point temperature.
Without temperature controller fitted.
The heater should automatically reset and provide water at the temperature set by
the internal limit switches.
Download from Www.Somanuals.co3m2. All Manuals Search And Download.
RESTARTING THE RINNAI WATER HEATER
Following a power cut the heaters should be restarted in this manner.
Standard system.
Single or multiple water heaters without remote controllers.
The heaters will automatically reset without any user involvement.
Single or multiple water heaters with remote controllers.
The heaters will be required to be switched on using the ON/OFF button on a remote
controller. Ensure that all taps/water outlets are closed and no water is flowing through
heaters.
Hot water system incorporating secondary recirculation pump.
Single or multiple water heaters without remote controllers.
The heater(s) will automatically reset without any user involvement.
Single or multiple water heater(s) with remote controller(s).
To reset the heaters follow the steps.
1. Turn off all hot water taps.
2. Turn off supply to secondary circulating pump or alternatively, if heater and pump
are fed from the same electrical supply, isolate pump flow.
3. Turn on heater at remote control.
4. Select required temperature.
5. Switch on supply to secondary circulating pump or open valve on pump flow.
The heater will now be ready to supply water at the set temperature.
If following the above procedure does not reset the heater switch it on and off at its main
supply, and then go through these steps again. If heater is still not working call your local
service agent or Rinnai for assistance.
Download from Www.Somanuals.co3m3. All Manuals Search And Download.
WIRING DIAGRAM
230 V
Download from Www.Somanuals.co3m4. All Manuals Search And Download.
DIAGNOSTIC POINTS
Diagnostic Points- To be read in conjunction with the wiring diagram.
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
SPECIFICATION
Model………………………………………………..…....………………………..Infinity 24e
Installation…………………………………………...………...……. External location only
Fuel…………………………………………………..….……………...Natural Gas or LPG *
Control………………………………………………….……………...……….…..Modulating
Input……………………………………………………..………….……………....5.8 to 52 kW
Exhaust type………………………………………..……..Forced Draught Direct Exhaust
Ignition………………………………………………...…………….…………...…..Electronic
Burner……………………………………………………...…………………...Stainless steel
Weight…………………………………………………...……….……………..…..………18kg
Water flow rate ………………………………………..……………….…...2.4** to 24L/min
Minimum operating water pressure…………………..……….…………..……….1.4 Bar
Connections
Gas…………………………………………………………...….………………….…….3/4BSP
Water Inlet………………………………………….………...…………………….……3/4BSP
Water outlet…………………………………….………...………………………….…..3/4BSP
Electrical Supply…………………………….…………..……………….230V AC 50Hz 1ph
* Separate models available for Natural gas or LPG fuel.
** Minimum flow rate based on temperature setpoint and inlet conditions.
Rinnai are continually updating and improving products and reserve the right to
alter model specifications without prior notice.
Download from Www.Somanuals.co3m6. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.co3m7. All Manuals Search And Download.
SERVICE CONTACT
Rinnai UK LTD.
9 Christleton Court
Manor Park
Runcorn
Cheshire
WA7 1ST
Tel. 01928 531870
Fax.01928 531880
E-mail. [email protected]
Web.
Download from Www.Somanuals.co3m8. All Manuals Search And Download.
COMMISSIONING CHECK LIST
Download from Www.Somanuals.co3m9. All Manuals Search And Download.
|